rtw88: coex: Change antenna setting to enhance free-run performance

While the mechanism goes to 2G_free_run or WL5G_BT2G,
set BT to hardware PTA mode to get a more efficiently performance.

Add a flag to indicate antenna switch is supported or not so
that the IC serials which has different antenna structure can
set antenna correctly.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-8-pkshih@realtek.com

rtw88: coex: update the TDMA parameter when leave LPS

The updated parameter and original parameter all means TDMA-OFF.
The original setting write 0x8 to firmware, but it only works for
some old IC series.
To avoid the confusing, update a proper parameter.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-7-pkshih@realtek.com

rtw88: coex: add the mechanism for RF4CE

Add the related coexistence mechanism about RF4CE and WLAN connected
flag to decide control packet is whether higher or normal priority.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-6-pkshih@realtek.com

rtw88: coex: Add force flag for coexistence table function

Because sometimes hardware action may be unpredictable.
(Ex: after WLAN LPS...etc)
Add a check mechanism if the action is triggered by
some concerned case, it can force to write the table again.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-5-pkshih@realtek.com

rtw88: coex: add write scoreboard action when WLAN in critical procedure

When WLAN in critical procedure, such as connecting, scan and so on,
coexistence will notify BT by scoreboard.
While BT firmware received the scoreboard interrupt, it will adjust
BT page priority lower to avoid WLAN critical procedure suffering impact.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-4-pkshih@realtek.com

rtw88: coex: remove unnecessary feature/function

Because the WLAN RSSI report feature had been implemented at WLAN link info
update function, it is redundant to update WLAN RSSI while BT is updating
link info, so remove the update WLAN RSSI part.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-3-pkshih@realtek.com

rtw88: coex: update TDMA settings for different beacon interval

Add considering for different WLAN beacon interval in coexistence
mechanism.
Because the WLAN beacon period may be not 100 ms, so it's necessary
to consider any beacon period and set timer according to the interval.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-2-pkshih@realtek.com

rtw88: add CCK_PD debug log

In order to help debugging in field, we add some log messages.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109090123.9254-2-pkshih@realtek.com

rtw88: 8723d: add cck pd seetings

CCK PD can reduce the number of false alarm of the CCK rates.
It dynamically adjusts the power threshold and CS ratio.
The values are compared to the values of the previous level, if
the level is changed, set new values of power threshold and CS
ratio.

Implement rtw_chip_ops::cck_pd_set() for 8723d.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109090123.9254-1-pkshih@realtek.com

rtw88: coex: simplify the setting and condition about WLAN TX limitation

Life time related setting is related to WLAN active port number,
not its mode. The original setting may cause poor WLAN performance.

In most case, WLAN TX limitation is helpful for BT in coexistence
scenario, especially for A2DP quality.
So this is necessary to fix the setting and constraint it.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-12-pkshih@realtek.com

rtw88: coex: add debug message

Since coexistence issue is related to WL/BT and each digital/analog/rf,
and these issues are often critical with low failure rate, add more
debugging information is helpful to clarify issues.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-11-pkshih@realtek.com

rtw88: coex: update WLAN 5G AFH parameter for 8822b

Adaptive Frequency Hopping(AFH) is a method of transmitting
radio signals by rapidly changing the carrier frequency among
many distinct frequencies, which can avoid interference.
Add this feature to update AFH parameter for 8822b.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-10-pkshih@realtek.com

rtw88: coex: change the parameter for A2DP when WLAN connecting

The original mechanism may cause A2DP glitch during WiFi connecting AP.
Because the original TDMA may decrease too much A2DP slot.
This patch add a timer and variable to let the case A2DP + WL_Connecting
performed more well.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-9-pkshih@realtek.com

rtw88: coex: modified for BT info notify

Add counter to count BT info C2H command for debug usage.
It could present the C2H channel situation.

Fix BT IQK state decision condition for counting.
The original condition is wrong, it would cause coexistence mechanism
going to the wrong strategy.

New format supports getting TDMA parameter from WL firmware, since
coexistence needs current TDMA parameter to decide strategy.

Remove unnecessary operations about scoreboard, it is not a must for
current version.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-8-pkshih@realtek.com

rtw88: coex: add separate flag for manual control

The original stop_dm flag is shared with the wifi and coexistence
mechanism internal usage, which represent two meanings, and makes
developers hard to debug.
Add a new flag manual_control for coexistence mechanism usage only.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-7-pkshih@realtek.com

rtw88: coex: Modify the timing of set_ant_path/set_rf_para

To make sure the related ANT/RF_PARA setting will be expected result in COEX.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-6-pkshih@realtek.com

rtw88: coex: coding style adjustment

Adjust space and comments, and fix "line over 80 characters" warnings
reported by checkpatch.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-5-pkshih@realtek.com

rtw88: coex: reduce magic number

Use macro definition to replace magic number.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-4-pkshih@realtek.com

rtw88: coex: update coex parameter to improve A2DP quality

Update COEX parameters and logic to enhance WL/BT performance
while WL_Busy + A2DP in a less interference environment.
It can avoid the interference comes cross from each other
and earned more performance.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-3-pkshih@realtek.com

rtw88: coex: fixed some wrong register definition and setting

Some register definition and bit definition were incorrect.
e.g. REG_BT_COEX_V2 should be word alignment to meet the coding style.
e.g. set REG_BT_TDMA_TIME[5:0]=0x5,
But the original is to set REG_BT_TDMA_TIME[7:0]=0x5.
This will cause unexpected hardware behavior.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-2-pkshih@realtek.com

rtlwifi: fix spelling typo of workaround

workarould -> workaround

Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604738439-24794-1-git-send-email-wangqing@vivo.com

rsi: Clean up loop in the interrupt handler

The inner do { ... } while loop is completely useless, all it does
is iterate over a switch-case statement, one bit at a time. This
can easily be replaced by simple if (status & bit) { ... } tests
for each bit. No functional change.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103180941.443528-2-marex@denx.de

rsi: Move card interrupt handling to RX thread

The interrupt handling of the RS911x is particularly heavy. For each RX
packet, the card does three SDIO transactions, one to read interrupt
status register, one to RX buffer length, one to read the RX packet(s).
This translates to ~330 uS per one cycle of interrupt handler. In case
there is more incoming traffic, this will be more.

The drivers/mmc/core/sdio_irq.c has the following comment, quote "Just
like traditional hard IRQ handlers, we expect SDIO IRQ handlers to be
quick and to the point, so that the holding of the host lock does not
cover too much work that doesn't require that lock to be held."

The RS911x interrupt handler does not fit that. This patch therefore
changes it such that the entire IRQ handler is moved to the RX thread
instead, and the interrupt handler only wakes the RX thread.

This is OK, because the interrupt handler only does things which can
also be done in the RX thread, that is, it checks for firmware loading
error(s), it checks buffer status, it checks whether a packet arrived
and if so, reads out the packet and passes it to network stack.

Moreover, this change permits removal of a code which allocated an
skbuff only to get 4-byte-aligned buffer, read up to 8kiB of data
into the skbuff, queue this skbuff into local private queue, then in
RX thread, this buffer is dequeued, the data in the skbuff as passed
to the RSI driver core, and the skbuff is deallocated. All this is
replaced by directly calling the RSI driver core with local buffer.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103180941.443528-1-marex@denx.de

mwifiex: pcie: skip cancel_work_sync() on reset failure path

If a reset is performed, but even the reset fails for some reasons (e.g.,
on Surface devices, the fw reset requires another quirks),
cancel_work_sync() hangs in mwifiex_cleanup_pcie().

    # firmware went into a bad state
    [...]
    [ 1608.281690] mwifiex_pcie 0000:03:00.0: info: shutdown mwifiex...
    [ 1608.282724] mwifiex_pcie 0000:03:00.0: rx_pending=0, tx_pending=1, cmd_pending=0
    [ 1608.292400] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
    [ 1608.292405] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
    # reset performed after firmware went into a bad state
    [ 1609.394320] mwifiex_pcie 0000:03:00.0: WLAN FW already running! Skip FW dnld
    [ 1609.394335] mwifiex_pcie 0000:03:00.0: WLAN FW is active
    # but even the reset failed
    [ 1619.499049] mwifiex_pcie 0000:03:00.0: mwifiex_cmd_timeout_func: Timeout cmd id = 0xfa, act = 0xe000
    [ 1619.499094] mwifiex_pcie 0000:03:00.0: num_data_h2c_failure = 0
    [ 1619.499103] mwifiex_pcie 0000:03:00.0: num_cmd_h2c_failure = 0
    [ 1619.499110] mwifiex_pcie 0000:03:00.0: is_cmd_timedout = 1
    [ 1619.499117] mwifiex_pcie 0000:03:00.0: num_tx_timeout = 0
    [ 1619.499124] mwifiex_pcie 0000:03:00.0: last_cmd_index = 0
    [ 1619.499133] mwifiex_pcie 0000:03:00.0: last_cmd_id: fa 00 07 01 07 01 07 01 07 01
    [ 1619.499140] mwifiex_pcie 0000:03:00.0: last_cmd_act: 00 e0 00 00 00 00 00 00 00 00
    [ 1619.499147] mwifiex_pcie 0000:03:00.0: last_cmd_resp_index = 3
    [ 1619.499155] mwifiex_pcie 0000:03:00.0: last_cmd_resp_id: 07 81 07 81 07 81 07 81 07 81
    [ 1619.499162] mwifiex_pcie 0000:03:00.0: last_event_index = 2
    [ 1619.499169] mwifiex_pcie 0000:03:00.0: last_event: 58 00 58 00 58 00 58 00 58 00
    [ 1619.499177] mwifiex_pcie 0000:03:00.0: data_sent=0 cmd_sent=1
    [ 1619.499185] mwifiex_pcie 0000:03:00.0: ps_mode=0 ps_state=0
    [ 1619.499215] mwifiex_pcie 0000:03:00.0: info: _mwifiex_fw_dpc: unregister device
    # mwifiex_pcie_work hang happening
    [ 1823.233923] INFO: task kworker/3:1:44 blocked for more than 122 seconds.
    [ 1823.233932]       Tainted: G        WC OE     5.10.0-rc1-1-mainline #1
    [ 1823.233935] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
    [ 1823.233940] task:kworker/3:1     state:D stack:    0 pid:   44 ppid:     2 flags:0x00004000
    [ 1823.233960] Workqueue: events mwifiex_pcie_work [mwifiex_pcie]
    [ 1823.233965] Call Trace:
    [ 1823.233981]  __schedule+0x292/0x820
    [ 1823.233990]  schedule+0x45/0xe0
    [ 1823.233995]  schedule_timeout+0x11c/0x160
    [ 1823.234003]  wait_for_completion+0x9e/0x100
    [ 1823.234012]  __flush_work.isra.0+0x156/0x210
    [ 1823.234018]  ? flush_workqueue_prep_pwqs+0x130/0x130
    [ 1823.234026]  __cancel_work_timer+0x11e/0x1a0
    [ 1823.234035]  mwifiex_cleanup_pcie+0x28/0xd0 [mwifiex_pcie]
    [ 1823.234049]  mwifiex_free_adapter+0x24/0xe0 [mwifiex]
    [ 1823.234060]  _mwifiex_fw_dpc+0x294/0x560 [mwifiex]
    [ 1823.234074]  mwifiex_reinit_sw+0x15d/0x300 [mwifiex]
    [ 1823.234080]  mwifiex_pcie_reset_done+0x50/0x80 [mwifiex_pcie]
    [ 1823.234087]  pci_try_reset_function+0x5c/0x90
    [ 1823.234094]  process_one_work+0x1d6/0x3a0
    [ 1823.234100]  worker_thread+0x4d/0x3d0
    [ 1823.234107]  ? rescuer_thread+0x410/0x410
    [ 1823.234112]  kthread+0x142/0x160
    [ 1823.234117]  ? __kthread_bind_mask+0x60/0x60
    [ 1823.234124]  ret_from_fork+0x22/0x30
    [...]

This is a deadlock caused by calling cancel_work_sync() in
mwifiex_cleanup_pcie():

- Device resets are done via mwifiex_pcie_card_reset()
- which schedules card->work to call mwifiex_pcie_card_reset_work()
- which calls pci_try_reset_function().
- This leads to mwifiex_pcie_reset_done() be called on the same workqueue,
  which in turn calls
- mwifiex_reinit_sw() and that calls
- _mwifiex_fw_dpc().

The problem is now that _mwifiex_fw_dpc() calls mwifiex_free_adapter()
in case firmware initialization fails. That ends up calling
mwifiex_cleanup_pcie().

Note that all those calls are still running on the workqueue. So when
mwifiex_cleanup_pcie() now calls cancel_work_sync(), it's really waiting
on itself to complete, causing a deadlock.

This commit fixes the deadlock by skipping cancel_work_sync() on a reset
failure path.

After this commit, when reset fails, the following output is
expected to be shown:

    kernel: mwifiex_pcie 0000:03:00.0: info: _mwifiex_fw_dpc: unregister device
    kernel: mwifiex: Failed to bring up adapter: -5
    kernel: mwifiex_pcie 0000:03:00.0: reinit failed: -5

To reproduce this issue, for example, try putting the root port of wifi
into D3 (replace "00:1d.3" with your setup).

    # put into D3 (root port)
    sudo setpci -v -s 00:1d.3 CAP_PM+4.b=0b

Cc: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201028142346.18355-1-kitakar@gmail.com

mwifiex: update comment for shutdown_sw()/reinit_sw() to reflect current state

The functions mwifiex_shutdown_sw() and mwifiex_reinit_sw() can be used
for more general purposes than the PCIe function level reset. Also, these
are even not PCIe-specific.

So, let's update the comments at the top of each function accordingly.

Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201028142110.18144-3-kitakar@gmail.com

mwifiex: fix mwifiex_shutdown_sw() causing sw reset failure

When a PCIe function level reset (FLR) is performed but without fw reset for
some reasons (e.g., on Microsoft Surface devices, fw reset requires other
quirks), it fails to reset wifi properly. You can trigger the issue on such
devices via debugfs entry for reset:

    $ echo 1 | sudo tee /sys/kernel/debug/mwifiex/mlan0/reset

and the resulting dmesg log:

    [   45.740508] mwifiex_pcie 0000:03:00.0: Resetting per request
    [   45.742937] mwifiex_pcie 0000:03:00.0: info: successfully disconnected from [BSSID]: reason code 3
    [   45.744666] mwifiex_pcie 0000:03:00.0: info: shutdown mwifiex...
    [   45.751530] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
    [   45.751539] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
    [   45.771691] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
    [   45.771695] mwifiex_pcie 0000:03:00.0: deleting the crypto keys
    [   45.771697] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
    [   45.771698] mwifiex_pcie 0000:03:00.0: deleting the crypto keys
    [   45.771699] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
    [   45.771701] mwifiex_pcie 0000:03:00.0: deleting the crypto keys
    [   45.771702] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
    [   45.771703] mwifiex_pcie 0000:03:00.0: deleting the crypto keys
    [   45.771704] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
    [   45.771705] mwifiex_pcie 0000:03:00.0: deleting the crypto keys
    [   45.771707] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
    [   45.771708] mwifiex_pcie 0000:03:00.0: deleting the crypto keys
    [   53.099343] mwifiex_pcie 0000:03:00.0: info: trying to associate to '[SSID]' bssid [BSSID]
    [   53.241870] mwifiex_pcie 0000:03:00.0: info: associated to bssid [BSSID] successfully
    [   75.377942] mwifiex_pcie 0000:03:00.0: cmd_wait_q terminated: -110
    [   85.385491] mwifiex_pcie 0000:03:00.0: info: successfully disconnected from [BSSID]: reason code 15
    [   87.539408] mwifiex_pcie 0000:03:00.0: cmd_wait_q terminated: -110
    [   87.539412] mwifiex_pcie 0000:03:00.0: deleting the crypto keys
    [   99.699917] mwifiex_pcie 0000:03:00.0: cmd_wait_q terminated: -110
    [   99.699925] mwifiex_pcie 0000:03:00.0: deleting the crypto keys
    [  111.859802] mwifiex_pcie 0000:03:00.0: cmd_wait_q terminated: -110
    [  111.859808] mwifiex_pcie 0000:03:00.0: deleting the crypto keys
    [...]

When comparing mwifiex_shutdown_sw() with mwifiex_pcie_remove(), it
lacks mwifiex_init_shutdown_fw().

This commit fixes mwifiex_shutdown_sw() by adding the missing
mwifiex_init_shutdown_fw().

Fixes: 4c5dae59d2e9 ("mwifiex: add PCIe function level reset support")
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201028142110.18144-2-kitakar@gmail.com

brcmfmac: Fix memory leak for unpaired brcmf_{alloc/free}

There are missig brcmf_free() for brcmf_alloc(). Fix memory leak
by adding missed brcmf_free().

Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Fixes: a1f5aac1765a ("brcmfmac: don't realloc wiphy during PCIe reset")
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1603849967-22817-1-git-send-email-sw0312.kim@samsung.com

rtlwifi: rtl8821ae: Place braces around empty if() body

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c: In function ‘_rtl8812ae_phy_get_txpower_limit’:
 drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c:2453:3: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]

Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-35-lee.jones@linaro.org

rtlwifi: rtl8821ae: phy: Remove a couple of unused variables

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c: In function ‘rtl8821ae_phy_switch_wirelessband’:
 drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c:597:14: warning: variable ‘rxpath’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c:597:6: warning: variable ‘txpath’ set but not used [-Wunused-but-set-variable]

Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-34-lee.jones@linaro.org

rtlwifi: rtl8723be: Remove set but unused variable 'cck_highpwr'

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/realtek/rtlwifi/rtl8723be/trx.c: In function ‘_rtl8723be_query_rxphystatus’:
 drivers/net/wireless/realtek/rtlwifi/rtl8723be/trx.c:53:6: warning: variable ‘cck_highpwr’ set but not used [-Wunused-but-set-variable]

Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-33-lee.jones@linaro.org

rtlwifi: halbtc8821a2ant: Remove a bunch of unused variables

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c: In function ‘btc8821a2ant_action_bt_inquiry’:
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:1451:40: warning: variable ‘bt_rssi_state’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:1451:22: warning: variable ‘wifi_rssi_state1’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:1451:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c: In function ‘btc8821a2ant_action_wifi_idle_process’:
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:1519:40: warning: variable ‘bt_rssi_state’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:1519:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c: In function ‘btc8821a2ant_action_pan_hs’:
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:2990:22: warning: variable ‘wifi_rssi_state1’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c: In function ‘btc8821a2ant_action_hid_a2dp’:
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:3277:22: warning: variable ‘wifi_rssi_state1’ set but not used [-Wunused-but-set-variable]

Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-31-lee.jones@linaro.org

rtlwifi: rtl8188ee: Remove set but unused variable 'reg_ea4'

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c: In function ‘_rtl88e_phy_path_a_iqk’:
 drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c:1351:33: warning: variable ‘reg_ea4’ set but not used [-Wunused-but-set-variable]

Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-30-lee.jones@linaro.org

rtlwifi: rtl8723be: Remove set but unused variable 'lc_cal'

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c: In function ‘_rtl8723be_phy_lc_calibrate’:
 drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c:2181:36: warning: variable ‘lc_cal’ set but not used [-Wunused-but-set-variable]

Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-29-lee.jones@linaro.org

rtlwifi: halbtc8821a1ant: Remove set but unused variable 'wifi_rssi_state'

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a1ant.c: In function ‘btc8821a1ant_run_coexist_mechanism’:
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a1ant.c:1904:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]

Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-28-lee.jones@linaro.org

rtlwifi: phy: Remove set but unused variable 'bbvalue'

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/realtek/rtlwifi/rtl8723ae/phy.c: In function ‘_rtl8723e_phy_iq_calibrate’:
 drivers/net/wireless/realtek/rtlwifi/rtl8723ae/phy.c:1150:6: warning: variable ‘bbvalue’ set but not used [-Wunused-but-set-variable]

Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-27-lee.jones@linaro.org

rtlwifi: halbtc8723b2ant: Remove a bunch of set but unused variables

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_wifi_idle_process’:
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:1631:40: warning: variable ‘bt_rssi_state’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:1631:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_sco’:
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2767:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_hid’:
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2810:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_a2dp’:
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2855:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_a2dp_pan_hs’:
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2929:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_pan_edr’:
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2976:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_pan_hs’:
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3028:22: warning: variable ‘wifi_rssi_state1’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3028:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_pan_edr_a2dp’:
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3066:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_pan_edr_hid’:
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3121:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_hid_a2dp_pan_edr’:
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3185:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_hid_a2dp’:
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3244:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]

Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-26-lee.jones@linaro.org

rtlwifi: rtl8192cu: trx: Demote clear abuse of kernel-doc format

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:455: warning: Function parameter or member 'txdesc' not described in '_rtl_tx_desc_checksum'

Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-6-lee.jones@linaro.org

rtlwifi: rtl8192cu: mac: Fix some missing/ill-documented function parameters

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/realtek/rtlwifi/rtl8192cu/mac.c:124: warning: Function parameter or member 'hw' not described in 'rtl92c_llt_write'
 drivers/net/wireless/realtek/rtlwifi/rtl8192cu/mac.c:124: warning: Excess function parameter 'io' description in 'rtl92c_llt_write'
 drivers/net/wireless/realtek/rtlwifi/rtl8192cu/mac.c:155: warning: Function parameter or member 'hw' not described in 'rtl92c_init_llt_table'
 drivers/net/wireless/realtek/rtlwifi/rtl8192cu/mac.c:155: warning: Excess function parameter 'io' description in 'rtl92c_init_llt_table'

Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-4-lee.jones@linaro.org

rtw88: rtw8822c: Remove unused variable 'corr_val'

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/realtek/rtw88/rtw8822c.c: In function ‘rtw8822c_dpk_dc_corr_check’:
 drivers/net/wireless/realtek/rtw88/rtw8822c.c:2445:5: warning: variable ‘corr_val’ set but not used [-Wunused-but-set-variable]

Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-39-lee.jones@linaro.org
Link: https://lore.kernel.org/r/20201102112410.1049272-39-lee.jones@linaro.org

wlcore: spi: Demote a non-compliant function header, fix another

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/ti/wlcore/spi.c:403: warning: Function parameter or member 'child' not described in 'wl12xx_spi_set_block_size'
 drivers/net/wireless/ti/wlcore/spi.c:403: warning: Function parameter or member 'blksz' not described in 'wl12xx_spi_set_block_size'
 drivers/net/wireless/ti/wlcore/spi.c:440: warning: Excess function parameter 'res' description in 'wlcore_probe_of'

Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Luciano Coelho <luciano.coelho@nokia.com>
Cc: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-36-lee.jones@linaro.org
Link: https://lore.kernel.org/r/20201102112410.1049272-37-lee.jones@linaro.org

mwifiex: pcie: Remove a couple of unchecked 'ret's

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/marvell/mwifiex/pcie.c: In function ‘mwifiex_pcie_remove’:
 drivers/net/wireless/marvell/mwifiex/pcie.c:432:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
 drivers/net/wireless/marvell/mwifiex/pcie.c: In function ‘mwifiex_cleanup_pcie’:
 drivers/net/wireless/marvell/mwifiex/pcie.c:3142:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]

Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Cc: Xinming Hu <huxinming820@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-32-lee.jones@linaro.org

wl3501_cs: Fix misspelling and provide missing documentation

Fixes the following W=1 kernel build warning(s):

 In file included from drivers/net/wireless/wl3501_cs.c:57:
 drivers/net/wireless/wl3501_cs.c:143: warning: Function parameter or member 'reg_domain' not described in 'iw_valid_channel'
 drivers/net/wireless/wl3501_cs.c:143: warning: Excess function parameter 'reg_comain' description in 'iw_valid_channel'
 drivers/net/wireless/wl3501_cs.c:469: warning: Function parameter or member 'data' not described in 'wl3501_send_pkt'
 drivers/net/wireless/wl3501_cs.c:469: warning: Function parameter or member 'len' not described in 'wl3501_send_pkt'

Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Fox Chen <mhchen@golf.ccl.itri.org.tw>
Cc: de Melo <acme@conectiva.com.br>
Cc: Gustavo Niemeyer <niemeyer@conectiva.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-25-lee.jones@linaro.org

prism54: isl_ioctl: Fix one function header and demote another

Fixes the following W=1 kernel build warning(s):

 from drivers/net/wireless/intersil/prism54/isl_ioctl.c:22:
 inlined from ‘prism54_get_name’ at drivers/net/wireless/intersil/prism54/isl_ioctl.c:283:2:
 drivers/net/wireless/intersil/prism54/isl_ioctl.c:68: warning: Function parameter or member 'priv' not described in 'prism54_mib_mode_helper'
 drivers/net/wireless/intersil/prism54/isl_ioctl.c:68: warning: Excess function parameter 'mib' description in 'prism54_mib_mode_helper'
 drivers/net/wireless/intersil/prism54/isl_ioctl.c:127: warning: Function parameter or member 'priv' not described in 'prism54_mib_init'

Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Aurelien Alleaume <slts@free.fr>
Cc: Valerio Riedel <hvr@gnu.org>
Cc: "Luis R. Rodriguez" <mcgrof@ruslug.rutgers.edu>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-15-lee.jones@linaro.org

wl1251: cmd: Rename 'len' to 'buf_len' in the documentation

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/ti/wl1251/cmd.c:70: warning: Function parameter or member 'buf_len' not described in 'wl1251_cmd_test'
 drivers/net/wireless/ti/wl1251/cmd.c:70: warning: Excess function parameter 'len' description in 'wl1251_cmd_test'

Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-10-lee.jones@linaro.org

brcmfmac: fweh: Add missing description for 'gfp'

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:394: warning: Function parameter or member 'gfp' not described in 'brcmf_fweh_process_event'

Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-19-lee.jones@linaro.org

brcmfmac: pcie: Provide description for missing function parameter 'devinfo'

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c:766: warning: Function parameter or member 'devinfo' not described in 'brcmf_pcie_bus_console_read'

Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-8-lee.jones@linaro.org

brcmfmac: bcmsdh: Fix description for function parameter 'pktlist'

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c:380: warning: Function parameter or member 'pktlist' not described in 'brcmf_sdiod_sglist_rw'
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c:380: warning: Excess function parameter 'pkt' description in 'brcmf_sdiod_sglist_rw'

Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-7-lee.jones@linaro.org

rsi: rsi_91x_usb_ops: Source file headers are not good candidates for kernel-doc

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/rsi/rsi_91x_usb_ops.c:22: warning: Incorrect use of kernel-doc format:  * rsi_usb_rx_thread() - This is a kernel thread to receive the packets from
 drivers/net/wireless/rsi/rsi_91x_usb_ops.c:29: warning: Function parameter or member 'common' not described in 'rsi_usb_rx_thread'

Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-5-lee.jones@linaro.org

rsi: rsi_91x_usb: Fix some basic kernel-doc issues

Fixes the following W=1 kernel build warning(s):

 drivers/net/wireless/rsi/rsi_91x_usb.c:26: warning: cannot understand function prototype: 'u16 dev_oper_mode = DEV_OPMODE_STA_BT_DUAL; '
 drivers/net/wireless/rsi/rsi_91x_usb.c:88: warning: Function parameter or member 'endpoint' not described in 'rsi_write_multiple'
 drivers/net/wireless/rsi/rsi_91x_usb.c:88: warning: Excess function parameter 'addr' description in 'rsi_write_multiple'
 drivers/net/wireless/rsi/rsi_91x_usb.c:320: warning: Function parameter or member 'ep_num' not described in 'rsi_rx_urb_submit'
 drivers/net/wireless/rsi/rsi_91x_usb.c:320: warning: Function parameter or member 'mem_flags' not described in 'rsi_rx_urb_submit'

Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-3-lee.jones@linaro.org

rt2x00: save survey for every channel visited

rt2800 only gives you survey for current channel.

Survey-based ACS algorithms are failing to perform their job when working
with rt2800.

Make rt2800 save survey for every channel visited and be able to give away
that information.

There is a bug registered https://dev.archive.openwrt.org/ticket/19081 and
this patch solves the issue.

Signed-off-by: Markov Mikhail <markov.mikhail@itmh.ru>
sgruszka: remove unused variable
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201104142524.94375-1-stf_xl@wp.pl

rtlwifi: Remove in_interrupt() usage in halbtc_send_bt_mp_operation()

halbtc_send_bt_mp_operation() uses in_interrupt() to determine if it is
safe to invoke wait_for_completion().

The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.

Aside of that in_interrupt() is not correct as it does not catch preempt
disabled regions which neither can sleep.

halbtc_send_bt_mp_operation() is called from:

 rtl_watchdog_wq_callback()
   rtl_btc_periodical()
     halbtc_get()
       case BTC_GET_U4_BT_PATCH_VER:
         halbtc_get_bt_patch_version()

 which is preemtible context.

   rtl_c2h_content_parsing()
     btc_ops->btc_btinfo_notify()
       rtl_btc_btinfo_notify()
         exhalbtc_bt_info_notify()
           ex_btc8723b1ant_bt_info_notify()
   ex_btc8821a1ant_bt_info_notify()
   ex_btc8821a2ant_bt_info_notify()
             btcoexist->btc_set_bt_reg()
               halbtc_set_bt_reg()

   rtl_c2h_content_parsing() is in turn called from:

   rtl_c2hcmd_wq_callback()
     rtl_c2hcmd_launcher()

   which is preemptible context and from:

   _rtl_pci_rx_interrupt
     rtl_c2hcmd_enqueue()

   which is obviously not preemptible but limited to C2H_BT_MP commands
   which does invoke rtl_c2h_content_parsing().

Aside of that it can be reached from:

     halbtc_get()
       case BTC_GET_U4_SUPPORTED_FEATURE:
         halbtc_get_bt_coex_supported_feature()
       case BTC_GET_U4_BT_FORBIDDEN_SLOT_VAL:
         halbtc_get_bt_forbidden_slot_val()
       case BTC_GET_U4_BT_DEVICE_INFO:
         halbtc_get_bt_device_info()
       case BTC_GET_U4_SUPPORTED_VERSION:
         halbtc_get_bt_coex_supported_version()
       case BTC_GET_U4_SUPPORTED_FEATURE:
         halbtc_get_bt_coex_supported_feature()

   btcoexist->btc_get_bt_afh_map_from_bt()
     halbtc_get_bt_afh_map_from_bt()

   btcoexist->btc_get_ble_scan_para_from_bt()
     halbtc_get_ble_scan_para_from_bt()

   btcoexist->btc_get_ble_scan_type_from_bt()
     halbtc_get_ble_scan_type_from_bt()

   btcoexist->btc_get_ant_det_val_from_bt()
     halbtc_get_ant_det_val_from_bt()

   btcoexist->btc_get_bt_coex_supported_version()
     halbtc_get_bt_coex_supported_version()

   btcoexist->btc_get_bt_coex_supported_feature()
     halbtc_get_bt_coex_supported_feature()

None of these have a caller. Welcome to the wonderful world of HALs and
onion layers.

Remove in_interrupt() check.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-9-bigeasy@linutronix.de

rtlwifi: Remove in_interrupt() usage in is_any_client_connect_to_ap().

is_any_client_connect_to_ap() is using in_interrupt() to determine whether
it should acquire the lock prior accessing the list.

The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.

The function is called from:

    - halbtc_get()

    - halbtc_get()
        halbtc_get_wifi_link_status()

    - halbtc_display_dbg_msg()
halbtc_display_wifi_status()
          halbtc_get_wifi_link_status()

All top level callers are part of the btc_coexist callback inferface and
are never invoked from a context which can hold the lock already.

The contexts which hold the lock are either protecting list add/del
operations or list walks which never call into any of the btc_coexist
interfaces.

In fact the conditional is outright dangerous because if this function
would be invoked from a BH disabled context the check would avoid taking
the lock while on another CPU the list could be manipulated under the lock.

Remove the in_interrupt() check and always acquire the lock.

To simplify the code further use list_empty() instead of walking the list
and counting the entries just to check the count for > 0 at the end.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-8-bigeasy@linutronix.de

zd1211rw: Remove in_atomic() usage.

The usage of in_atomic() in driver code is deprecated as it can not
always detect all states where it is not allowed to sleep.

All callers are in premptible thread context and all functions invoke core
functions which have checks for invalid calling contexts already.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-7-bigeasy@linutronix.de

hostap: Remove in_atomic() check.

hostap_get_wireless_stats() is the iw_handler_if::get_wireless_stats()
callback of this driver. This callback was not allowed to sleep until
commit a160ee69c6a46 ("wext: let get_wireless_stats() sleep") in v2.6.32.

Remove the therefore pointless in_atomic() check.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Jouni Malinen <j@w1.fi>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-6-bigeasy@linutronix.de

airo: Replace in_atomic() usage.

issuecommand() is using in_atomic() to decide if it is safe to invoke
schedule() while waiting for the command to be accepted.

Usage of in_atomic() for this is only half correct as it can not detect all
condition where it is not allowed to schedule(). Also Linus clearly
requested that code which changes behaviour depending on context should
either be seperated or the context be conveyed in an argument passed by the
caller, which usually knows the context.

Add an may_sleep argument to issuecommand() indicating when it is save to
sleep and change schedule() to cond_resched() because it's pointless to
invoke schedule() if there is no request to reschedule.

Pass the may_sleep condition through the various call chains leading to
issuecommand().

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-5-bigeasy@linutronix.de

airo: Always use JOB_STATS and JOB_EVENT

issuecommand() is using in_atomic() to decide if it is safe to invoke
schedule() while waiting for the command to be accepted.

Usage of in_atomic() for this is only half correct as it can not detect all
condition where it is not allowed to schedule(). Also Linus clearly
requested that code which changes behaviour depending on context should
either be seperated or the context be conveyed in an argument passed by the
caller, which usually knows the context.

Chasing the call chains leading up to issuecommand() is straight forward,
but airo_link() and airo_get_stats() would require to pass the context
through a quite large amount of functions.

As this is ancient hardware, avoid the churn and enforce the invocation of
those functions through the JOB machinery.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-4-bigeasy@linutronix.de

airo: Invoke airo_read_wireless_stats() directly

airo_get_wireless_stats() is the iw_handler_if::get_wireless_stats()
callback of this driver. This callback was not allowed to sleep until
commit a160ee69c6a46 ("wext: let get_wireless_stats() sleep") in v2.6.32.

airo still delegates the readout to a thread, which is not longer
necessary.

Invoke airo_read_wireless_stats() directly from the callback and remove
the now unused JOB_WSTATS handling.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-3-bigeasy@linutronix.de

orinoco: Remove BUG_ON(in_interrupt/irq())

The usage of in_irq()/in_interrupt() in drivers is phased out and the
BUG_ON()'s based on those are not covering all contexts in which these
functions cannot be called.

Aside of that BUG_ON() should only be used as last resort, which is clearly
not the case here.

A broad variety of checks in the invoked functions (always enabled or debug
option dependent) cover these conditions already, so the BUG_ON()'s do not
really provide additional value.

Just remove them.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-2-bigeasy@linutronix.de

rtl8xxxu: Add Buffalo WI-U3-866D to list of supported devices

Buffalo WI-U3-866D is supported by the rtl8812au driver.
Also RTL8812AU software supports the product RTL8192EU also.
So add Buffalo WI-U3-866D with the RTL8192EU driver info.

Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101173236.7851-1-ikegami.t@gmail.com

rtw88: decide lps deep mode from firmware feature.

This patch checks the supported lps deep mode from firmware feature,
and allows different firmware have different deep power mode.
Original module parameter rtw_fw_lps_deep_mode is replaced with
rtw_disable_lps_deep_mode for user to disable lps deep mode.

Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030084826.9034-5-tehuang@realtek.com

rtw88: add C2H response for checking firmware leave lps

Originally driver checks if firmware has left lps via reading the setting
of REG_TCR register. But this way may fail when firmware is frequently
changing power state. Therefore, firmware provides a safer option for
driver. When firmware leaves lps successfully, it sends a C2H response
to inform driver.

Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030084826.9034-4-tehuang@realtek.com

rtw88: store firmware feature in firmware header

Some functions need the support of firmware with special version.
In order to get the feature of current firmware, we store the information
in firmware header and parse after firmware is loaded. The current feature
list in firmware header includes checking leave lps via C2H and
supported lps deep mode.

Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030084826.9034-3-tehuang@realtek.com

rtw88: sync the power state between driver and firmware

In current flow, driver issues power requests to firmware for entering or
leaving deep power mode. But driver does not wait for an ack from firmware
via reading CPWM register when driver requests to enter deep power mode.
The behavior will lead to unsynchronized state between firmware and driver.
Furthermore, consecutive same power requests may confuse firmware and leads
to unexpected value of CPWM register. This patch ensures that the power
request will wait for an ack from firmware and only send one power request
each time.

Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030084826.9034-2-tehuang@realtek.com

rtw88: coex: separate BLE HID profile from BLE profile

BT firmware will report BLE-HID and BLE-RCU in different profile.
We can distinguish the two profile from BT info now.

Add the coexistence for BLE-HID coexistence,
it can make BLE HID work more smoothly.

BLE-HID need to Tx/Rx packet more frequently to respond
user operation, but RCU doesn't.

In the case of RCU coexistence, it will make Wi-Fi have a
higher priority to earn more Wi-Fi throughput.

If BLE-HID go for the same case,
it will make user feel mouse is lagging.

Desired BT firmware BT-COEX version: 0x1c
Desired WL firmware version: 9.9

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030055506.6560-1-pkshih@realtek.com

rtlwifi: Fix non-canonical address access issues

During realtek USB wireless NIC initialization, it's unexpected
disconnection will cause urb sumbmit fail. On the one hand,
_rtl_usb_cleanup_rx will be called to clean up rx stuff, especially for
rtl_wq. On the other hand, disconnection will cause rtl_usb_disconnect
and _rtl_usb_cleanup_rx to be called. So, rtl_wq will be flush/destroy
twice, which will cause non-canonical address 0xdead000000000122 access
and general protection fault.

Fixed this issue by remove _rtl_usb_cleanup_rx when urb sumbmit fail.

Signed-off-by: WeitaoWangoc <WeitaoWang-oc@zhaoxin.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1603768580-2798-1-git-send-email-WeitaoWang-oc@zhaoxin.com

brcmfmac: fix SDIO access for big-endian host

These full-mac chips use little-endian byte ordering. This patch
adds a few missing conversions to/from little-endian so that the
driver may be used with a big-endian host.

Signed-off-by: Remi Depommier <rde@setrix.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201020174639.28892-1-rde@setrix.com

rtw88: remove extraneous 'const' qualifier

clang -Wextra warns about functions returning a 'const' integer:

drivers/net/wireless/realtek/rtw88/rtw8822b.c:90:8: warning: 'const' type qualifier on return type has no effect [-Wignored-qualifiers]
static const u8 rtw8822b_get_swing_index(struct rtw_dev *rtwdev)

Remove the extra qualifier here.

Fixes: c97ee3e0bea2 ("rtw88: add power tracking support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201026213040.3889546-7-arnd@kernel.org

rtlwifi: fix -Wpointer-sign warning

There are thousands of warnings in a W=2 build from just one file:

drivers/net/wireless/realtek/rtlwifi/rtl8821ae/table.c:3788:15: warning: pointer targets in initialization of 'u8 *' {aka 'unsigned char *'} from 'char *' differ in signedness [-Wpointer-sign]

Change the types to consistently use 'const char *' for the
strings.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201026213040.3889546-6-arnd@kernel.org

net: hostap: fix function cast warning

gcc -Wextra complains about the function type cast:

drivers/net/wireless/intersil/hostap/hostap_hw.c:3173:48: warning: cast between incompatible function types from ‘void (*)(struct tasklet_struct *)’ to ‘void (*)(long unsigned int)’ [-Wcast-function-type]

Avoid this by just using the regular tasklet_setup() function instead
of the incorrect homegrown version.

Fixes: 7433c9690318 ("intersil: convert tasklets to use new tasklet_setup() API")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201026213040.3889546-2-arnd@kernel.org

wireless: remove unneeded break

A break is not needed if it is preceded by a return

Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201020125841.26791-1-trix@redhat.com

rsi: Fix TX EAPOL packet handling against iwlwifi AP

In case RSI9116 SDIO WiFi operates in STA mode against Intel 9260 in AP mode,
the association fails. The former is using wpa_supplicant during association,
the later is set up using hostapd:

iwl$ cat hostapd.conf
interface=wlp1s0
ssid=test
country_code=DE
hw_mode=g
channel=1
wpa=2
wpa_passphrase=test
wpa_key_mgmt=WPA-PSK
iwl$ hostapd -d hostapd.conf

rsi$ wpa_supplicant -i wlan0 -c <(wpa_passphrase test test)

The problem is that the TX EAPOL data descriptor RSI_DESC_REQUIRE_CFM_TO_HOST
flag and extended descriptor EAPOL4_CONFIRM frame type are not set in case the
AP is iwlwifi, because in that case the TX EAPOL packet is 2 bytes shorter.

The downstream vendor driver has this change in place already [1], however
there is no explanation for it, neither is there any commit history from which
such explanation could be obtained.

[1] https://github.com/SiliconLabs/RS911X-nLink-OSD/blob/master/rsi/rsi_91x_hal.c#L238

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201015111616.429220-1-marex@denx.de

wlcore: Use fallthrough pseudo-keyword

In order to enable -Wimplicit-fallthrough for Clang[1], replace the
existing /* fall-through */ comments with the new pseudo-keyword
macro fallthrough[2].

[1] https://git.kernel.org/linus/e2079e93f562c7f7a030eb7642017ee5eabaaa10
[2] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201008220905.GA8040@embeddedor

ray_cs: Use fallthrough pseudo-keyword

In order to enable -Wimplicit-fallthrough for Clang[1], replace the
existing /* fall through */ comments with the new pseudo-keyword
macro fallthrough[2].

[1] https://git.kernel.org/linus/e2079e93f562c7f7a030eb7642017ee5eabaaa10
[2] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201008220422.GA6926@embeddedor

wireless: mt7601u: convert tasklets to use new tasklet_setup() API

In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.

Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201007103309.363737-3-allen.lkml@gmail.com

Linux 5.10-rc1

treewide: Convert macro and uses of __section(foo) to __section("foo")

Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.

Remove the quote operator # from compiler_attributes.h __section macro.

Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.

Conversion done using the script at:

    https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.pl

Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/sys.c: fix prototype of prctl_get_tid_address()

tid_addr is not a "pointer to (pointer to int in userspace)"; it is in
fact a "pointer to (pointer to int in userspace) in userspace".  So
sparse rightfully complains about passing a kernel pointer to
put_user().

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: remove kzfree() compatibility definition

Commit 453431a54934 ("mm, treewide: rename kzfree() to
kfree_sensitive()") renamed kzfree() to kfree_sensitive(),
but it left a compatibility definition of kzfree() to avoid
being too disruptive.

Since then a few more instances of kzfree() have slipped in.

Just get rid of them and remove the compatibility definition
once and for all.

Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: enable GIT_DIR environment use to set git repository location

If set, use the environment variable GIT_DIR to change the default .git
location of the kernel git tree.

If GIT_DIR is unset, keep using the current ".git" default.

Link: https://lkml.kernel.org/r/c5e23b45562373d632fccb8bc04e563abba4dd1d.camel@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'timers-urgent-2020-10-25' of git://git./linux/kernel/git/tip/tip

Pull timer fixes from Thomas Gleixner:
 "A time namespace fix and a matching selftest. The futex absolute
  timeouts which are based on CLOCK_MONOTONIC require time namespace
  corrected. This was missed in the original time namesapce support"

* tag 'timers-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  selftests/timens: Add a test for futex()
  futex: Adjust absolute futex timeouts with per time namespace offset

Merge tag 'sched-urgent-2020-10-25' of git://git./linux/kernel/git/tip/tip

Pull scheduler fixes from Thomas Gleixner:
 "Two scheduler fixes:

   - A trivial build fix for sched_feat() to compile correctly with
     CONFIG_JUMP_LABEL=n

   - Replace a zero lenght array with a flexible array"

* tag 'sched-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/features: Fix !CONFIG_JUMP_LABEL case
  sched: Replace zero-length array with flexible-array

Merge tag 'perf-urgent-2020-10-25' of git://git./linux/kernel/git/tip/tip

Pull perf fix from Thomas Gleixner:
 "A single fix to compute the field offset of the SNOOPX bit in the data
  source bitmask of perf events correctly"

* tag 'perf-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: correct SNOOPX field offset

Merge tag 'locking-urgent-2020-10-25' of git://git./linux/kernel/git/tip/tip

Pull locking fix from Thomas Gleixner:
 "Just a trivial fix for kernel-doc warnings"

* tag 'locking-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/seqlocks: Fix kernel-doc warnings

Merge tag 'ntb-5.10' of git://github.com/jonmason/ntb

Pull NTB fixes from Jon Mason.

* tag 'ntb-5.10' of git://github.com/jonmason/ntb:
  NTB: Use struct_size() helper in devm_kzalloc()
  ntb: intel: Fix memleak in intel_ntb_pci_probe
  NTB: hw: amd: fix an issue about leak system resources

Merge branch 'i2c/for-5.10' of git://git./linux/kernel/git/wsa/linux

Pull i2c fix from Wolfram Sang:
 "Regression fix for rc1 and stable kernels as well"

* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: core: Restore acpi_walk_dep_device_list() getting called after registering the ACPI i2c devs

Merge tag '5.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6

Pull more cifs updates from Steve French:
 "Add support for stat of various special file types (WSL reparse points
  for char, block, fifo)"

* tag '5.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module version number
  smb3: add some missing definitions from MS-FSCC
  smb3: remove two unused variables
  smb3: add support for stat of WSL reparse points for special file types

Merge branch 'parisc-5.10-2' of git://git./linux/kernel/git/deller/parisc-linux

Pull more parisc updates from Helge Deller:

 - During this merge window O_NONBLOCK was changed to become 000200000,
   but we missed that the syscalls timerfd_create(), signalfd4(),
   eventfd2(), pipe2(), inotify_init1() and userfaultfd() do a strict
   bit-wise check of the flags parameter.

   To provide backward compatibility with existing userspace we
   introduce parisc specific wrappers for those syscalls which filter
   out the old O_NONBLOCK value and replaces it with the new one.

 - Prevent HIL bus driver to get stuck when keyboard or mouse isn't
   attached

 - Improve error return codes when setting rtc time

 - Minor documentation fix in pata_ns87415.c

* 'parisc-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  ata: pata_ns87415.c: Document support on parisc with superio chip
  parisc: Add wrapper syscalls to fix O_NONBLOCK flag usage
  hil/parisc: Disable HIL driver when it gets stuck
  parisc: Improve error return codes when setting rtc time

Merge tag 'for-linus-5.10b-rc1c-tag' of git://git./linux/kernel/git/xen/tip

Pull more xen updates from Juergen Gross:

 - a series for the Xen pv block drivers adding module parameters for
   better control of resource usge

 - a cleanup series for the Xen event driver

* tag 'for-linus-5.10b-rc1c-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  Documentation: add xen.fifo_events kernel parameter description
  xen/events: unmask a fifo event channel only if it was masked
  xen/events: only register debug interrupt for 2-level events
  xen/events: make struct irq_info private to events_base.c
  xen: remove no longer used functions
  xen-blkfront: Apply changed parameter name to the document
  xen-blkfront: add a parameter for disabling of persistent grants
  xen-blkback: add a parameter for disabling of persistent grants

Merge tag 'safesetid-5.10' of git://github.com/micah-morton/linux

Pull SafeSetID updates from Micah Morton:
 "The changes are mostly contained to within the SafeSetID LSM, with the
  exception of a few 1-line changes to change some ns_capable() calls to
  ns_capable_setid() -- causing a flag (CAP_OPT_INSETID) to be set that
  is examined by SafeSetID code and nothing else in the kernel.

  The changes to SafeSetID internally allow for setting up GID
  transition security policies, as already existed for UIDs"

* tag 'safesetid-5.10' of git://github.com/micah-morton/linux:
  LSM: SafeSetID: Fix warnings reported by test bot
  LSM: SafeSetID: Add GID security policy handling
  LSM: Signal to SafeSetID when setting group IDs

Merge tag '20201024-v4-5.10' of git://git./linux/kernel/git/wtarreau/prandom

Pull random32 updates from Willy Tarreau:
 "Make prandom_u32() less predictable.

  This is the cleanup of the latest series of prandom_u32
  experimentations consisting in using SipHash instead of Tausworthe to
  produce the randoms used by the network stack.

  The changes to the files were kept minimal, and the controversial
  commit that used to take noise from the fast_pool (f227e3ec3b5c) was
  reverted. Instead, a dedicated "net_rand_noise" per_cpu variable is
  fed from various sources of activities (networking, scheduling) to
  perturb the SipHash state using fast, non-trivially predictable data,
  instead of keeping it fully deterministic. The goal is essentially to
  make any occasional memory leakage or brute-force attempt useless.

  The resulting code was verified to be very slightly faster on x86_64
  than what is was with the controversial commit above, though this
  remains barely above measurement noise. It was also tested on i386 and
  arm, and build- tested only on arm64"

Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
* tag '20201024-v4-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wtarreau/prandom:
  random32: add a selftest for the prandom32 code
  random32: add noise from network and scheduling activity
  random32: make prandom_u32() output unpredictable

i2c: core: Restore acpi_walk_dep_device_list() getting called after registering the ACPI i2c devs

Commit 21653a4181ff ("i2c: core: Call i2c_acpi_install_space_handler()
before i2c_acpi_register_devices()")'s intention was to only move the
acpi_install_address_space_handler() call to the point before where
the ACPI declared i2c-children of the adapter where instantiated by
i2c_acpi_register_devices().

But i2c_acpi_install_space_handler() had a call to
acpi_walk_dep_device_list() hidden (that is I missed it) at the end
of it, so as an unwanted side-effect now acpi_walk_dep_device_list()
was also being called before i2c_acpi_register_devices().

Move the acpi_walk_dep_device_list() call to the end of
i2c_acpi_register_devices(), so that it is once again called *after*
the i2c_client-s hanging of the adapter have been created.

This fixes the Microsoft Surface Go 2 hanging at boot.

Fixes: 21653a4181ff ("i2c: core: Call i2c_acpi_install_space_handler() before i2c_acpi_register_devices()")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209627
Reported-by: Rainer Finke <rainer@finke.cc>
Reported-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Suggested-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Merge tag 'block-5.10-2020-10-24' of git://git.kernel.dk/linux-block

Pull block fixes from Jens Axboe:

 - NVMe pull request from Christoph
     - rdma error handling fixes (Chao Leng)
     - fc error handling and reconnect fixes (James Smart)
     - fix the qid displace when tracing ioctl command (Keith Busch)
     - don't use BLK_MQ_REQ_NOWAIT for passthru (Chaitanya Kulkarni)
     - fix MTDT for passthru (Logan Gunthorpe)
     - blacklist Write Same on more devices (Kai-Heng Feng)
     - fix an uninitialized work struct (zhenwei pi)"

 - lightnvm out-of-bounds fix (Colin)

 - SG allocation leak fix (Doug)

 - rnbd fixes (Gioh, Guoqing, Jack)

 - zone error translation fixes (Keith)

 - kerneldoc markup fix (Mauro)

 - zram lockdep fix (Peter)

 - Kill unused io_context members (Yufen)

 - NUMA memory allocation cleanup (Xianting)

 - NBD config wakeup fix (Xiubo)

* tag 'block-5.10-2020-10-24' of git://git.kernel.dk/linux-block: (27 commits)
  block: blk-mq: fix a kernel-doc markup
  nvme-fc: shorten reconnect delay if possible for FC
  nvme-fc: wait for queues to freeze before calling update_hr_hw_queues
  nvme-fc: fix error loop in create_hw_io_queues
  nvme-fc: fix io timeout to abort I/O
  null_blk: use zone status for max active/open
  nvmet: don't use BLK_MQ_REQ_NOWAIT for passthru
  nvmet: cleanup nvmet_passthru_map_sg()
  nvmet: limit passthru MTDS by BIO_MAX_PAGES
  nvmet: fix uninitialized work for zero kato
  nvme-pci: disable Write Zeroes on Sandisk Skyhawk
  nvme: use queuedata for nvme_req_qid
  nvme-rdma: fix crash due to incorrect cqe
  nvme-rdma: fix crash when connect rejected
  block: remove unused members for io_context
  blk-mq: remove the calling of local_memory_node()
  zram: Fix __zram_bvec_{read,write}() locking order
  skd_main: remove unused including <linux/version.h>
  sgl_alloc_order: fix memory leak
  lightnvm: fix out-of-bounds write to array devices->info[]
  ...

Merge tag 'io_uring-5.10-2020-10-24' of git://git.kernel.dk/linux-block

Pull io_uring fixes from Jens Axboe:

 - fsize was missed in previous unification of work flags

 - Few fixes cleaning up the flags unification creds cases (Pavel)

 - Fix NUMA affinities for completely unplugged/replugged node for io-wq

 - Two fallout fixes from the set_fs changes. One local to io_uring, one
   for the splice entry point that io_uring uses.

 - Linked timeout fixes (Pavel)

 - Removal of ->flush() ->files work-around that we don't need anymore
   with referenced files (Pavel)

 - Various cleanups (Pavel)

* tag 'io_uring-5.10-2020-10-24' of git://git.kernel.dk/linux-block:
  splice: change exported internal do_splice() helper to take kernel offset
  io_uring: make loop_rw_iter() use original user supplied pointers
  io_uring: remove req cancel in ->flush()
  io-wq: re-set NUMA node affinities if CPUs come online
  io_uring: don't reuse linked_timeout
  io_uring: unify fsize with def->work_flags
  io_uring: fix racy REQ_F_LINK_TIMEOUT clearing
  io_uring: do poll's hash_node init in common code
  io_uring: inline io_poll_task_handler()
  io_uring: remove extra ->file check in poll prep
  io_uring: make cached_cq_overflow non atomic_t
  io_uring: inline io_fail_links()
  io_uring: kill ref get/drop in personality init
  io_uring: flags-based creds init in queue

Merge tag 'libata-5.10-2020-10-24' of git://git.kernel.dk/linux-block

Pull libata fixes from Jens Axboe:
 "Two minor libata fixes:

   - Fix a DMA boundary mask regression for sata_rcar (Geert)

   - kerneldoc markup fix (Mauro)"

* tag 'libata-5.10-2020-10-24' of git://git.kernel.dk/linux-block:
  ata: fix some kernel-doc markups
  ata: sata_rcar: Fix DMA boundary mask

Merge branch 'work.misc' of git://git./linux/kernel/git/viro/vfs

Pull misc vfs updates from Al Viro:
 "Assorted stuff all over the place (the largest group here is
  Christoph's stat cleanups)"

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: remove KSTAT_QUERY_FLAGS
  fs: remove vfs_stat_set_lookup_flags
  fs: move vfs_fstatat out of line
  fs: implement vfs_stat and vfs_lstat in terms of vfs_fstatat
  fs: remove vfs_statx_fd
  fs: omfs: use kmemdup() rather than kmalloc+memcpy
  [PATCH] reduce boilerplate in fsid handling
  fs: Remove duplicated flag O_NDELAY occurring twice in VALID_OPEN_FLAGS
  selftests: mount: add nosymfollow tests
  Add a "nosymfollow" mount option.

Merge tag 'dma-mapping-5.10-1' of git://git.infradead.org/users/hch/dma-mapping

Pull dma-mapping fixes from Christoph Hellwig:

 - document the new dma_{alloc,free}_pages() API

 - two fixups for the dma-mapping.h split

* tag 'dma-mapping-5.10-1' of git://git.infradead.org/users/hch/dma-mapping:
  dma-mapping: document dma_{alloc,free}_pages
  dma-mapping: move more functions to dma-map-ops.h
  ARM/sa1111: add a missing include of dma-map-ops.h

Merge tag 'for-linus' of git://git./virt/kvm/kvm

Pull KVM fixes from Paolo Bonzini:
 "Two fixes for this merge window, and an unrelated bugfix for a host
  hang"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: ioapic: break infinite recursion on lazy EOI
  KVM: vmx: rename pi_init to avoid conflict with paride
  KVM: x86/mmu: Avoid modulo operator on 64-bit value to fix i386 build

Merge tag 'x86_seves_fixes_for_v5.10_rc1' of git://git./linux/kernel/git/tip/tip

Pull x86 SEV-ES fixes from Borislav Petkov:
 "Three fixes to SEV-ES to correct setting up the new early pagetable on
  5-level paging machines, to always map boot_params and the kernel
  cmdline, and disable stack protector for ../compressed/head{32,64}.c.
  (Arvind Sankar)"

* tag 'x86_seves_fixes_for_v5.10_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot/64: Explicitly map boot_params and command line
  x86/head/64: Disable stack protection for head$(BITS).o
  x86/boot/64: Initialize 5-level paging variables earlier

random32: add a selftest for the prandom32 code

Given that this code is new, let's add a selftest for it as well.
It doesn't rely on fixed sets, instead it picks 1024 numbers and
verifies that they're not more correlated than desired.

Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
Cc: George Spelvin <lkml@sdf.org>
Cc: Amit Klein <aksecurity@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: tytso@mit.edu
Cc: Florian Westphal <fw@strlen.de>
Cc: Marc Plumb <lkml.mplumb@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>

random32: add noise from network and scheduling activity

With the removal of the interrupt perturbations in previous random32
change (random32: make prandom_u32() output unpredictable), the PRNG
has become 100% deterministic again. While SipHash is expected to be
way more robust against brute force than the previous Tausworthe LFSR,
there's still the risk that whoever has even one temporary access to
the PRNG's internal state is able to predict all subsequent draws till
the next reseed (roughly every minute). This may happen through a side
channel attack or any data leak.

This patch restores the spirit of commit f227e3ec3b5c ("random32: update
the net random state on interrupt and activity") in that it will perturb
the internal PRNG's statee using externally collected noise, except that
it will not pick that noise from the random pool's bits nor upon
interrupt, but will rather combine a few elements along the Tx path
that are collectively hard to predict, such as dev, skb and txq
pointers, packet length and jiffies values. These ones are combined
using a single round of SipHash into a single long variable that is
mixed with the net_rand_state upon each invocation.

The operation was inlined because it produces very small and efficient
code, typically 3 xor, 2 add and 2 rol. The performance was measured
to be the same (even very slightly better) than before the switch to
SipHash; on a 6-core 12-thread Core i7-8700k equipped with a 40G NIC
(i40e), the connection rate dropped from 556k/s to 555k/s while the
SYN cookie rate grew from 5.38 Mpps to 5.45 Mpps.

Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
Cc: George Spelvin <lkml@sdf.org>
Cc: Amit Klein <aksecurity@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: tytso@mit.edu
Cc: Florian Westphal <fw@strlen.de>
Cc: Marc Plumb <lkml.mplumb@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>