Aleksei Mamlin [Thu, 22 Oct 2015 10:38:56 +0000 (13:38 +0300)]
ARM: dts: sun4i: Enable audio codec on Marsboard A10.
Enable on-chip audio codec on the Marsboard A10.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Tue, 20 Oct 2015 22:04:29 +0000 (00:04 +0200)]
ARM: dts: sun4i: Add dts file for the pov protab2-ips9 tablet
The Point of View protab2-ips9 is a tablet with a 9" ips 1024x768 lcd screen,
microsd slot, headphones, mini hdmi, mini usb b and power barrel connectors.
It uses a rtl8188cus usb wifi chip and a RDA 5875Y bluetooth chip attached
to uart2. It has a bma250 accelerometer attached to i2c1 addr 0x18, this
only works when ldo3 is set to 2.8 volt, otherwise i2c1 gets stuck, so
for now we mark i2c1 as failed.
It has a pixcir,pixcir_tangoc compatible touchscreen attached to i2c2 addr
0x5c. This is not enabled in this dts, because this variant of the
pixcir_tangoc has separate wakeup and enable pins both of which need
to be driven low before the touchscreen will work. Before we can enable
this the pixcir driver and devicetree-bindings need to be extended to
support these pins.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Thu, 22 Oct 2015 04:30:26 +0000 (12:30 +0800)]
ARM: sun4i: Enable cubieboard audio codec
The cubieboard uses the internal codec to output sound to its mini-jack.
Enable it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 28 Jul 2015 08:37:01 +0000 (10:37 +0200)]
ARM: sun5i: chip: Enable the audio codec
The CHIP v0.2 has a composite output on a mini-jack connector, the audio
part being provided by the on-SoC codec. Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Marcus Cooper [Wed, 10 Jun 2015 14:31:01 +0000 (16:31 +0200)]
ARM: sun4i: Enable audio-codec on Mele A1000
Enable the audio-codec on the Mele A1000 top-set box.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Maxime Ripard [Fri, 1 May 2015 20:39:45 +0000 (22:39 +0200)]
ARM: sun7i: Enable cubieboard2 audio codec
The cubieboard2 uses the internal codec to output sound to its mini-jack.
Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Emilio López [Mon, 18 Aug 2014 04:10:05 +0000 (01:10 -0300)]
ARM: sun7i: dt: enable audio codec on Cubietruck
This commit enables the on-chip audio codec present on the A20 SoC
for the Cubietruck.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Emilio López [Mon, 18 Aug 2014 04:07:55 +0000 (01:07 -0300)]
ARM: sun7i: Add sunxi codec device node
The A20 SoC includes the Allwinner audio codec, capable of both 24-bit
playback and capture. This commit adds a device node for it.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Maxime Ripard [Mon, 27 Jul 2015 14:50:21 +0000 (16:50 +0200)]
ARM: sun5i: Add the Audio codec DT node
The A13 and A10s also have the audio codec present. List it in the device
tree.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Marcus Cooper [Tue, 22 Jul 2014 11:06:48 +0000 (13:06 +0200)]
ARM: sun4i: Add sunxi codec device node
The A10 SoC includes the Allwinner audio codec, capable of both 24-bit
playback and capture. This commit adds a device node for it.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Maxime Ripard [Mon, 12 Oct 2015 20:28:46 +0000 (22:28 +0200)]
ARM: sun7i: Add audio codec clock
The audio codec functional clock is a child of PLL2 and is used to control
the audio rate, enable it in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Maxime Ripard [Mon, 12 Oct 2015 20:28:46 +0000 (22:28 +0200)]
ARM: sun5i: Add audio codec clock
The audio codec functional clock is a child of PLL2 and is used to control
the audio rate, enable it in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Maxime Ripard [Mon, 12 Oct 2015 20:28:46 +0000 (22:28 +0200)]
ARM: sun4i: Add audio codec clock
The audio codec functional clock is a child of PLL2 and is used to control
the audio rate, enable it in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Maxime Ripard [Mon, 12 Oct 2015 20:21:49 +0000 (22:21 +0200)]
ARM: sun7i: Add audio PLL
The A20 uses the PLL2 as the audio PLL, which is the parent of all the
other audio clocks in the system (i2s, codec, etc.). Add it to the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Maxime Ripard [Mon, 12 Oct 2015 20:21:49 +0000 (22:21 +0200)]
ARM: sun5i: Add audio PLL
The A13 uses the PLL2 as the audio PLL, which is the parent of all the
other audio clocks in the system (i2s, codec, etc.). However, it has a
different divider configuration than the A10, hence the difference
compatible.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Maxime Ripard [Mon, 12 Oct 2015 20:21:49 +0000 (22:21 +0200)]
ARM: sun4i: Add audio PLL
The A10 uses the PLL2 as the audio PLL, which is the parent of all the
other audio clocks in the system (i2s, codec, etc.). Add it to the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Adam Sampson [Sat, 17 Oct 2015 22:08:29 +0000 (23:08 +0100)]
ARM: dts: sun7i: Enable USB DRC on pcDuino v3 Nano
The OTG arrangement on the LinkSprite pcDuino v3 Nano is the same as the
pcDuino 1/2/3: the OTG port's 5V line is connected directly to the 5V
bus (it's not switchable), and the OTG port's ID pin is connected to PH4
on the A20.
Tested successfully in both host and device modes.
Signed-off-by: Adam Sampson <ats@offog.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Sat, 17 Oct 2015 16:04:09 +0000 (00:04 +0800)]
ARM: dts: sun6i: Add support for Sinlinx A31s SDK board
The Sinlinx A31s SDK is a A31s based module/baseboard development kit.
The core module has the SoC, PMIC, DRAM, eMMC and supporting components.
There are also pads for UART0, JTAG and I2S.
The baseboard has 100 Mbps Ethernet, 5x USB 2.0 host ports via a USB 2.0
hub chip, MMC, HDMI, SPDIF, CIR, audio jacks, 2 tablet-like volume
buttons, RS232 style UART and USB OTG (though VBUS is not connected).
Various headers are available for other addon modules, such as SDIO
WiFi, LCD display, camera sensor, UARTs, I2C, SPI and GPIOs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Thu, 15 Oct 2015 14:28:47 +0000 (16:28 +0200)]
ARM: dts: sun6i: Add a dts file for the Sinovoip BPI-M2 board
The Sinovoip BPI-M2 is a SBC board based on the A31s SoC it features
1G RAM, a microsd slot, Gbit ethernet, 4 usb-a USB-2 ports, ir receiver,
stereo headphone jack and hdmi video output.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Thu, 15 Oct 2015 14:28:46 +0000 (16:28 +0200)]
ARM: dts: sun6i: Add mmc2_pins_a pinmux setting to sun6i-a31.dtsi
Add a pinmux setting for using mmc2 in regular 4 bit mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Thu, 15 Oct 2015 14:28:45 +0000 (16:28 +0200)]
ARM: dts: sunxi: Fix interrupt-cells for [r]pio on A23/A31/A33/A80
When the gpio interrupt bindings where changed to add a bank to the
specifier list, the r_pio nodes of A23/A31/A33 where not updated to
match and neither was the pio node of the A80, this fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Wed, 14 Oct 2015 16:32:21 +0000 (00:32 +0800)]
ARM: dts: sun8i: Add NMI interrupt controller node
The NMI interrupt controller is in charge of the NMI pin exposed by
the SoC to the PMIC. The PMIC signals interrupts through this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Sat, 10 Oct 2015 14:48:59 +0000 (22:48 +0800)]
ARM: dts: sun6i: hummingbird: Enable AXP221 DC5LDO regulator as "vdd-cpus"
The DC5LDO regulator supplies VDD-CPUS, which is for the embedded
controller in the A31 SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Sat, 10 Oct 2015 14:48:58 +0000 (22:48 +0800)]
ARM: dts: sun6i: hummingbird: Use axp22x.dtsi for AXP221 regulators
Now that we have axp22x.dtsi describing common axp22x hardware, use
it and reference the nodes instead of declaring the whole tree.
Also drop the "always-on" from the vdd-gpu regulator, since we don't
support the GPU anyway.
And add a regulator reference for cpu0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Sat, 10 Oct 2015 14:48:56 +0000 (22:48 +0800)]
ARM: dts: sun6i: hummingbird: Fix VDD-CPU and VDD-GPU regulator names
The VDD-CPU and VDD-GPU regulators were incorrectly swapped.
Fixes: bab03561224ba ("ARM: dts: sun6i: hummingbird: Add AXP221 regulator
nodes")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Adam Sampson [Sat, 10 Oct 2015 20:15:21 +0000 (21:15 +0100)]
ARM: dts: sun7i: Add regulator configuration for pcDuino v3 Nano
The power configuration on this board is the same as the pcDuino v3.
This will enable frequency/voltage scaling over the standard A20
operating points from 144 MHz to 960 MHz.
Tested using cpufreq-ljt-stress-test on two pcDuino v3 Nano boards; also
tested successfully with voltages reduced by 0.025 V.
Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Tue, 13 Oct 2015 12:37:45 +0000 (14:37 +0200)]
ARM: dts: sun6i: Turn on gmac on Colombus
We've everything we need to support the gmac on Colombus, turn it on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Tue, 13 Oct 2015 12:35:48 +0000 (14:35 +0200)]
ARM: dts: sun8i: Make et-q8-v1.6.dts a symlink to q8-tablet.dts
A33 Q8 tablets with the et-q8-v1.6 pcb will work fine with the
generic q8-tablet.dts and given the many variants of PCBs found in
Q8 tablets using such a specific dts name was a mistake in hindsight.
We cannot just drop the et-q8-v1.6.dtb as existing u-boot configs
may very well point to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Tue, 13 Oct 2015 12:35:47 +0000 (14:35 +0200)]
ARM: dts: sun8i: Make ippo-q8h-v*.dts a symlink to q8-tablet.dts
A23 Q8 tablets with the ippo-q8h-v* pcb will work fine with the
generic q8-tablet.dts and given the many variants of PCBs found in
Q8 tablets using such a specific dts name was a mistake in hindsight.
We cannot just drop the ippo-q8h-v*.dtb as existing u-boot configs
may very well point to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Tue, 13 Oct 2015 12:35:46 +0000 (14:35 +0200)]
ARM: dts: sun8i: Add sun8i-a23-q8-tablet.dts file
This is a generic dts file for A23 based q8 formfactor tablets,
this is intended to replace both sun8i-a23-ippo-q8h-v5.dts and
sun8i-a23-ippo-q8h-v1.2.dts (these can be fully dropped after a
transition period).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 11 Oct 2015 09:55:08 +0000 (11:55 +0200)]
ARM: dts: sun5i: Add backlight node to sun5i-q8-common.dtsi
All A13 based q8 formfactor tablets use the same backlight setup, add
a backlight devicetree node for controlling the backlight on these devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Sun, 11 Oct 2015 09:55:07 +0000 (11:55 +0200)]
ARM: dts: sunxi: Enable PWM controller on Q8 format tablets
Q8 format tablets use channel 0 of the PWM controller for backlight dimming.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 11 Oct 2015 09:55:06 +0000 (11:55 +0200)]
ARM: dts: sun5i: Add PWM channel 0 pinmux setting for A13/A10s
Add a pinmux setting for the first pwm channel. This is often used for
backlight dimming on tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 11 Oct 2015 09:55:05 +0000 (11:55 +0200)]
ARM: dts: sun5i: Add PWM controller node for A13 / A10s
Add dts nodes for the PWM controller on the A13 / A10s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 9 Jun 2015 17:38:43 +0000 (19:38 +0200)]
ARM: sun5i: Add C.H.I.P DTS
The C.H.I.P. is a small SBC with an Allwinner R8, 8GB of NAND, 512MB of
RAM, USB host and OTG, a wifi / bluetooth combo chip, an audio/video jack
and two connectors to plug additional boards on top of it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Chen-Yu Tsai [Sat, 10 Oct 2015 14:48:57 +0000 (22:48 +0800)]
ARM: dts: sunxi: Add dtsi for AXP22x PMIC
The AXP22x family of PMIC is used with some Allwinner SoCs. This
includes the AXP221, AXP221s and AXP223. They differ in the host
interface, maximum supply current for DCDC1 regulator, and default
voltage and state for various LDO regulators. Also, the AXP221s
does not support fine calibration of the battery fuel gauge.
This patch adds a dtsi file for all the common bindings for these
PMICs. Currently this is just listing all the regulator nodes. The
regulators are initialized based on their device node names.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Adam Sampson [Sat, 10 Oct 2015 12:52:52 +0000 (13:52 +0100)]
ARM: dts: sun7i: Correct USB regulators on pcDuino v3 Nano
The LinkSprite pcDuino v3 Nano's two USB host ports are powered by a
single RT9701GB regulator, which has its enable input tied to the A20's
PD2 pin, pulled up to 3v3 via a 10k resistor.
However, the script.bin that shipped with the device listed PH11 and PH3
as Vbus control pins for the two USB ports. Neither of these are
actually connected to anything.
Siarhei Siamashka spotted this problem while reviewing the other
LinkSprite boards. This patch fixes it by only defining a single
regulator, controlled by PD2. Testing shows that the USB ports are now
(correctly) only powered up once the USB PHY driver is loaded.
Reported-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Adam Sampson <ats@offog.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Mon, 22 Jun 2015 10:00:30 +0000 (12:00 +0200)]
ARM: sun5i: dt: Add UART3 CTS and RTS pins
Add a separate pinctrl node for the UART3 CTS and RTS pins shared between
the A10s and A13.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Maxime Ripard [Mon, 22 Jun 2015 09:56:09 +0000 (11:56 +0200)]
ARM: sun5i: dt: Move uart3 pinctrl node to common DTSI
The uart3 pins are shared between the A10s and A13, move the pinctrl node
to the common DTSI to avoid duplication.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Maxime Ripard [Fri, 18 Sep 2015 07:09:34 +0000 (09:09 +0200)]
ARM: sun5i: Add R8 DTSI
The R8 is very close to the A13, but it still has a few differences,
notably a composite output, which the A13 lacks.
Add a DTSI based on the A13's to hold those differences.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Siarhei Siamashka [Fri, 9 Oct 2015 11:09:39 +0000 (14:09 +0300)]
ARM: dts: sun4i: Enable USB DRC on pcDuino1/2
Enable the otg/drc usb controller on the pcDuino1/2 board. Note
that the pcDuino1 FEX file from the vendor contains the following
information in the [usbc0] section:
usb_id_gpio = port:PH04<0><1><default><default>
usb_det_vbus_gpio = port:PH05<0><0><default><default>
usb_drv_vbus_gpio = port:PB09<1><0><default><0>
While the pcDuino2 FEX has:
usb_id_gpio = port:PH04<0><1><default><default>
usb_det_vbus_gpio = port:PH05<0><0><default><default>
usb_drv_vbus_gpio = port:PD02<1><0><default><0>
The ID pin is indeed PH4. The PD2 pin can be used to switch power
on/off for the USB Type A receptacle on pcDuino2, but it has nothing
to do with the MicroUSB OTG receptacle. The VBUS pin of the MicroUSB
receptacle is always connected to 5V according to the schematics
(both pcDuino1 and pcDuino2) and confirmed by doing some tests on
pcDuino2. The PH5 pin is just one of the pins on the J8 expansion
header and has nothing to do with USB OTG. The PB9 pin is pulled
up and connected to the N_VBUSEN pin of AXP209 PMIC, while the
VBUS pin of AXP209 only has a capacitor between it and the
ground (this pin is not used for anything else).
To sum it up. Only the ID pin (PH4) has a real use. And 5V voltage
is always served to the MicroUSB OTG receptacle no matter what is
the state of the PB9/PD2 pins.
This patch has been tested on pcDuino2 to work fine in a host role
with a USB keyboard connected via an OTG cable. It also works fine
in a device role (cdc_ether) with a regular Micro-B cable connected
to a desktop PC.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Siarhei Siamashka [Fri, 9 Oct 2015 11:09:38 +0000 (14:09 +0300)]
ARM: sun4i: dt: Add new LinkSprite pcDuino2 board
The LinkSprite pcDuino2 board is almost identical to the older
LinkSprite pcDuino1 board according to the schematic pdf files.
So we just include the existing "sun4i-a10-pcduino.dts" file and
make the necessary adjustments.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Siarhei Siamashka [Fri, 9 Oct 2015 11:09:37 +0000 (14:09 +0300)]
ARM: dts: sun4i: Allow to use the PH6 pin for GPIO on pcDuino1/2
The pcDuino1 board does not use any power switches at all for its
two USB host ports and the VBUS pins are always connected to 5V.
The pcDuino2 board uses the RT9701GB power switch for its single
USB host port, but the USB_EN pin (PD2) is pulled up with a 10K
resistor. So that the USB power is still enabled by default,
resulting in the same behaviour as pcDuino1 if nobody touches
the PD2 pin. This minor difference is going to be handled in a
follow-up patch, introducing a separate dts file for pcDuino2.
The primary reason for this fix is that the current dts file
unnecessarily meddles with the PH3 and PH6 pins. But the PH6 pin
is available on the Arduino-compatible expansion header and may
have a better use for other purposes. This patch fixes the
problem and now the PH6 pin can be used with the GPIO sysfs
interface. Tested on a pcDuino2 board with a multimeter:
echo 230 > /sys/class/gpio/export
echo "out" > /sys/class/gpio/gpio230/direction
echo 0 > /sys/class/gpio/gpio230/value
echo 1 > /sys/class/gpio/gpio230/value
USB still works as expected too.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Tue, 22 Sep 2015 13:36:01 +0000 (15:36 +0200)]
ARM: dts: sun7i: Enable USB DRC on Bananapi
Enable the otg/drc usb controller on the Bananapi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Timo Sigurdsson [Wed, 7 Oct 2015 22:18:36 +0000 (00:18 +0200)]
ARM: dts: sunxi: Add regulators for LeMaker BananaPi
sun7i-a20-bananapi.dts doesn't contain regulator nodes for the AXP209 PMU
driver, so add them to allow for voltage-scaling with cpufreq-dt. Also
add board-specific OPP to use slightly higher voltages at lower
frequencies since Kevin Hilman reported that not all BananaPi boards run
stable at the default voltages inherited by sun7i-a20.dtsi.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Wed, 30 Sep 2015 06:39:47 +0000 (14:39 +0800)]
ARM: dts: sun6i: hummingbird: Drop AXP221 DC1SW and DC5LDO supplies
"dcdc1-supply" and "dcdc5-supply" have been dropped, as they are
internally connected and should not be represented in the device
tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Thu, 1 Oct 2015 11:57:51 +0000 (19:57 +0800)]
ARM: dts: sun8i: sinlinx-sina33: Enable Reduced Serial Bus controller
The Reduced Serial Bus controller is used to talk to the onboard PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Thu, 1 Oct 2015 11:57:50 +0000 (19:57 +0800)]
ARM: dts: sun8i: q8-common: Enable RSB controller for A23/A33 Q8 tablets
The Reduced Serial Bus controller is used to talk to the onboard PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Thu, 1 Oct 2015 11:57:49 +0000 (19:57 +0800)]
ARM: dts: sun8i: Add Reduced Serial Bus controller device node to A23/A33 dtsi
This patch adds a device node for the Reduced Serial Bus (RSB)
controller and the defacto pinmux setting to the A23/A33 dtsi.
Since there is only one possible pinmux setting for RSB, just
set it in the dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Siarhei Siamashka [Sun, 4 Oct 2015 18:58:48 +0000 (21:58 +0300)]
ARM: dts: sun4i: Add AXP209 PMU regulators for pcDuino1/2
This allows voltage-scaling with cpufreq-dt. The reliability of
voltage-scaling has been checked by reducing the voltage of all
operating points by 0.025V (for extra safety headroom) and running
libjpeg-turbo decoding tests on 5 pcDuino2 boards. It means that
the standard sun4i voltages should be perfectly fine too.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Marcus Cooper [Wed, 30 Sep 2015 17:34:39 +0000 (19:34 +0200)]
ARM: sun7i: dt: Add new Olimex A20 EVB device
The A20-SOM-EVB is a reference design of a 2-layer board for the
A20-SOM.
It expands the features of A20-SOM by adding VGA connector, HDMI
connector, audio In/Out, LCD connector, 2 Mpix camera, gigabit
Ethernet, SATA, USB-OTG and 2 USB hosts.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Thu, 1 Oct 2015 12:48:29 +0000 (20:48 +0800)]
ARM: dts: sun6i: hummingbird: Add aliases for rtc devices
The hummingbird A31 has 2 rtc devices available: one in the SoC,
and a pcf8563 external rtc on i2c2.
For some unknown reason, the onboard backup battery alone can not
supply enough power to the internal rtc. When external power is
removed, the internal rtc would reset. Hence we want to use the
external one by default.
Add aliases for the rtc devices with the external one as rtc0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Jelle de Jong [Tue, 22 Sep 2015 13:36:05 +0000 (15:36 +0200)]
ARM: dts: sun7i: Add dts file for Wits Pro A20 DKT
The Wits Pro A20 DKT is an A20 Development KiT with 1G RAM, 4G NAND,
sdio wifi, 1Gbit ethernet, 1024x768 lcd screen with ft5x_ts touchscreen
and a ton of IO connectors.
Note there seem to be multiple sdcard slots on the board (4 in total), but
other then mmc0 none of these are hooked up by default, there is a ton of
dip-switches which likely allow hooking some of these up, but the
documentation of the board only describes the use of a fraction of them,
so for now we only support mmc0.
Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl>
[hdegoede@redhat.com: Use pwrseq instead of a regulator for the wifi-en pin]
[hdegoede@redhat.com: Add support for OOB irq for the sdio wifi]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Aleksei Mamlin [Tue, 22 Sep 2015 13:36:04 +0000 (15:36 +0200)]
ARM: dts: sun7i: Enable USB DRC on Wexler TAB7200
Enable the otg/drc usb controller on the Wexler TAB7200 tablet.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reinder de Haan [Tue, 22 Sep 2015 13:36:03 +0000 (15:36 +0200)]
ARM: dts: sun7i: Enable USB DRC on the Orange pi
Add usb otg support for Orange pi, based on Orange pi mini.
Signed-off-by: Reinder de Haan <patchesrdh@mveas.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Tue, 22 Sep 2015 13:36:02 +0000 (15:36 +0200)]
ARM: dts: sun7i: Enable USB DRC on orangepi-mini
Enable the otg/drc usb controller on the orangepi-mini.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Tue, 22 Sep 2015 13:36:00 +0000 (15:36 +0200)]
ARM: dts: axp209: Add usb_power_supply child node to the ax209 node
Add a node representing the usb power supply part of the axp209 pmic, note
that the usb power supply and the (to be added later) ac power supply will
each have their own child-node, so that they can be separately specified
as power-supply for other nodes using a power-supply property with a
phandle pointing to the right axp209 child-node.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Thu, 24 Sep 2015 15:23:54 +0000 (17:23 +0200)]
ARM: dts: sun8i: Make ippo-q8h-v1.2.dts a symlink to q8-tablet.dts
A33 Q8 tablets with the ippo-q8h-v1.2 pcb will work fine with the
generic q8-tablet.dts and given the many variants of PCBs found in
Q8 tablets using such a specific dts name was a mistake in hindsight.
We cannot just drop the ippo-q8h-v1.2.dtb as existing u-boot configs
may very well point to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Thu, 24 Sep 2015 15:23:53 +0000 (17:23 +0200)]
ARM: dts: sun8i: Add sun8i-a33-q8-tablet.dts file
This is a generic dts file for A33 based q8 formfactor tablets,
this is intended to replace both sun8i-a33-ippo-q8h-v1.2.dts and
sun8i-a33-et-q8-v1.6.dts (these can be fully dropped after a
transition period).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Lawrence Yu [Tue, 22 Sep 2015 15:50:50 +0000 (08:50 -0700)]
ARM: dts: sun6i: Add support for Yones Toptech bs1078v2 tablets
The bs1078v2 is a pcb found in 10.1" tablets with an A31 soc, 1G RAM
and 8G NAND, rtl8723as usb wifi, 1 micro USB OTG port, 1 USB HOST port
This commit adds a dts for v2 of the bs1078 pcb.
Signed-off-by: Lawrence Yu <lyu@micile.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Aleksei Mamlin [Thu, 24 Sep 2015 07:33:46 +0000 (10:33 +0300)]
ARM: dts: sun4i: Enable USB DRC on the Marsboard A10
Enable the otg/drc usb controller on the Marsboard A10.
Similar to Cubieboard, the 5V of the otg is directly connected to the
general 5V, so we only use the id pin.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Priit Laes [Wed, 23 Sep 2015 07:38:31 +0000 (10:38 +0300)]
ARM: dts: sun4i: gemei-g9: Add accelerometer (bma250) IRQ
Add IRQ configuration for bma250 accelerometer.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Wed, 23 Sep 2015 04:34:39 +0000 (12:34 +0800)]
ARM: dts: sun8i-a33: Add security system crypto engine clock and device nodes
A33 has the same "Security System" crypto engine as A10/A20, but with a
separate reset control.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Sun, 20 Sep 2015 12:30:50 +0000 (08:30 -0400)]
ARM: dts: sun8i: Add pwm-backlight device for A23/A33 Q8 format tablets
The LCD backlight on the A23/A33 Q8 format tablets is enabled
with a GPIO controlled regulator, and brightness controlled with
the SoC's PWM controller.
The backlight is powered from the AXP223 PMIC's DC1SW output,
which is not supported yet. A proper bootloader is required
to enable it.
The brightness levels are arbitrary. The FEX files do not have
such information. As such, actual brightness levels may differ
from device to device.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 18 Aug 2015 17:36:18 +0000 (19:36 +0200)]
ARM: sun8i: A23: Add missing msgbox gate
Even though it's not mentionned in the A23 user manual, the A23 has a gate
for the AHB1 clock to the msgbox IP. Add it to the clock-indices.
Reported-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 18 Aug 2015 17:34:06 +0000 (19:34 +0200)]
ARM: sun8i: Move A23 AHB1 gates out of common DTSI
The AHB1 gates were assumed to be identical between the A23 and the A33,
which turned out to be wrong. Move the A23 gates definition to the A23
DTSI.
Reported-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 18 Aug 2015 17:32:56 +0000 (19:32 +0200)]
ARM: sun8i: Add the A33 AHB1 gates clock driver
The A33 has a different gates array than the A23, add the node to the DT.
Reported-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sat, 5 Sep 2015 14:55:53 +0000 (16:55 +0200)]
ARM: dts: sun5i: Add dts file for q8 formfactor a13 based tablets
This commits adds a generic dts file for q8 formfactor a13 based tablets.
The tablets ship in many variants, with the difference mainly being the
touchscreen controller / accelerometer / wifi chip used.
The wifi is USB based, and thus not listed in devicetree.
The touchscreen controller / accelerometer may turn out to be a problem
once we add support for those. We can either do something with devicetree
overlays, or add sun5i-a13-<touchscreen>-<accelerometer>.dts files. The
latter is what the android mod community is doing with firmware images.
This dts was tested with an a13 q8 tablet with a pcb labelled: "94V-0",
silead gsl1680 touchscreen controller and a mc32x0 accelerometer.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sat, 5 Sep 2015 14:55:52 +0000 (16:55 +0200)]
ARM: dts: sun5i: Add sun5i-q8-common.dtsi
This is the sun5i / a13 version of sun8i-q8-common.dtsi for use in dts
files for a13 q8 based tablets. Compared to sun8i this uses uart1 for the
serial console, and PG0 for card-detect for mmc0.
This also adds pmic and otg support, which both use the same config on
all known q8 a13 devices. This is not present in sun5i-q8-common.dtsi
because pmic / otg support for sun8i has not yet been merged.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Fri, 18 Sep 2015 07:35:37 +0000 (15:35 +0800)]
ARM: dts: sun8i: Add PWM channel 0 pinmux setting for A23/A33
The PWM controller has 2 outputs, with one usable pin for each.
Add a pinmux setting for the first channel. This is often used
for backlight dimming on tablets.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Fri, 18 Sep 2015 07:35:36 +0000 (15:35 +0800)]
ARM: dts: sun8i: Add PWM controller node for A23/A33
A23/A33 have a PWM controller that is compatible to the one on the A20.
Add a device node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Yassin Jaffer [Tue, 15 Sep 2015 14:05:54 +0000 (00:05 +1000)]
ARM: dts: sun7i: Add keypad clk node
This patch add support to the keypad clock on sun7i
Signed-off-by: Yassin Jaffer <yassinjaffer@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Sander Vermin [Sun, 13 Sep 2015 18:26:01 +0000 (20:26 +0200)]
ARM: dts: sun6i: Add accelerometer on Columbus A31
Add mma8452 accelerometer to sun6i-a31-colombus.dts.
Signed-off-by: Sander Vermin <sander@vermin.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Jelle van der Waa [Thu, 10 Sep 2015 13:05:59 +0000 (15:05 +0200)]
ARM: dts: sun5i: Add dts file for the Wobo i5 top set box
The Wobo i5 top set box is a somewhat curious A10s based top set box,
it uses an AXP209 rather then the AXP152 usually used in combination
with the A10s. It has an ethernet phy connected to PORTD rather then
PORTA, and its built-in usb wifi is connected via the otg controller.
This commit adds a dts file adding support for this top set box.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Jelle van der Waa [Thu, 10 Sep 2015 13:05:58 +0000 (15:05 +0200)]
ARM: dts: sun5i: Add emac_pins_b definition
The emac pins on an A10s can also be routed to the outside through
PORTD rather then through PORTA, add a pinctrl node for this.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Olliver Schinagl [Thu, 10 Sep 2015 08:31:21 +0000 (10:31 +0200)]
dts: sunxi: add eeprom to A20 OLinuXino micro board
The Olimex A20 OLinuXino Micro features an eeprom that is always on the
board. This patch adds it to the dts.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Olliver Schinagl [Thu, 10 Sep 2015 08:31:20 +0000 (10:31 +0200)]
dts: sunxi: add eeprom to A20 OLinuXino Lime2 board
The Olimex A20 OLinuXino Lime2 features an eeprom that is always on the
board. This patch adds it to the dts.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Olliver Schinagl [Thu, 10 Sep 2015 08:31:19 +0000 (10:31 +0200)]
dts: sunxi: add eeprom to A20 OLinuXino Lime board
The Olimex A20 OLinuXino Lime features an eeprom that is always on the
board. This patch adds it to the dts.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Olliver Schinagl [Thu, 10 Sep 2015 08:31:18 +0000 (10:31 +0200)]
dts: sunxi: correct vendor prefix on OLinuXino a10s micro
The OLinuXino A10S micro features an eeprom. According to the eeprom.txt
binding document, we should use the manufacturer and 'at' is not the
proper manufacturer id according to the vendor-prefixes.
This patch takes the proper vendor-prefix and uses it for the eeprom
node.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Olliver Schinagl [Thu, 10 Sep 2015 08:31:17 +0000 (10:31 +0200)]
dts: sunxi: add eeprom to A10 OLinuXino Lime board
The Olimex A10 OLinuXino Lime features an eeprom that is always on the
board. This patch adds it to the dts.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Wed, 9 Sep 2015 08:23:24 +0000 (10:23 +0200)]
ARM: dts: sun4i: Add dts file for iNet-1 based tablets
The iNet-tek iNet-1 PCB is a PCB found in various generic 10.1" 1024x600
A10 based tablets such as the Point of View Protab2 XXL and the
Cherry M1007.
This patch has been tested on both rev2 and rev5 of this board / these
tablets.
It comes with a rtl8188cus usb wifi connected to ehci1, focal ft5406ee8
touchscreen connected to i2c2 addr 0x38, bosch bma 250 accelerometer
connected to i2c1 addr 0x18 and the usual connectors: headphone,
mini hdmi, power-barrel, mini-usb and a micro-sd slot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Wed, 9 Sep 2015 08:23:23 +0000 (10:23 +0200)]
ARM: dts: sun4i: Add dts file inet9f-rev03 based tablets
The inet9f-rev03 pcb is specially designed for gaming tablets, such as
the qware tb-g100 tablet.
These 7" tablets feature a dpad, firebuttons and 2 joysticks on the sides
of the screen.
Besides this they have the usual connectors: power-barrel, mini usb,
mini hdmi, headphone and micro-sd slot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sat, 5 Sep 2015 14:55:51 +0000 (16:55 +0200)]
ARM: dts: sunxi: Add sun?i-q8-common.dtsi files for q8 tablets
Cheap allwinner based devices in the q8 enclosure come in many variants,
all sharing the case and a number of other basic features.
They differ in the display, touchscreen, accelerometer and wifi chips
used.
This commit adds 2 dtsi files defining the shared features of all the
q8 tablets. sunxi-q8-common.dtsi defines features shared amongst all
q8 tablets, sun8i-q8-common.dtsi defines features shared amongst all
a23 / a33 based q8 tablets, but not with a13 q8 based tablets.
a13 based tablets use a different card-detect pin for the mmc, and
use uart1 instead of the r_uart for the serial console.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Fri, 28 Aug 2015 13:15:17 +0000 (15:15 +0200)]
ARM: dts: sun5i: Add dts file for inet98v_rev2 based tablets
The inet98v_rev2 is a pcb used in generic A13 based tablets. It features
volume buttons, a power barrel, micro-usb otg, headphone connector and
a power button.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Fri, 28 Aug 2015 09:54:37 +0000 (17:54 +0800)]
ARM: dts: sun6i: Add mmc2 pins for 8 bit emmc
This also includes the reset pin for emmc.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Fri, 28 Aug 2015 09:54:34 +0000 (17:54 +0800)]
ARM: dts: sun6i: Add lradc node
sun6i also has the LRADC for tablet buttons.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 23 Aug 2015 22:37:26 +0000 (00:37 +0200)]
ARM: dts: sun4i: inet97fv2: Enable i2c1 and i2c2 controllers
Enable i2c1 and i2c2 controllers, these are used for the touchscreen resp.
the accelerometer.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 23 Aug 2015 22:37:25 +0000 (00:37 +0200)]
ARM: dts: sun4i: inet97fv2: Enable support for tablet keys
Enable support for the tablet keys which are connected via the lradc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 23 Aug 2015 22:37:24 +0000 (00:37 +0200)]
ARM: dts: sun4i: inet97fv2: Enable otg controller
Enable the otg controller on the inet97fv2 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 23 Aug 2015 22:37:23 +0000 (00:37 +0200)]
ARM: dts: sun4i: inet97fv2: Add regulator nodes
Use axp209.dtsi and add regulator nodes for the regulators used on the
inet97fv2 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Sun, 23 Aug 2015 22:37:22 +0000 (00:37 +0200)]
ARM: dts: sun4i: inet97fv2: Disable unused usb controllers
The inet97fv2 tablet only has a usb-2 wifi device connected to the second
ehci controller, disable the first ehci controller and both ohci
controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Fri, 7 Aug 2015 15:22:33 +0000 (17:22 +0200)]
ARM: dts: sun5i: Add support for the Auxtek-T003 HDMI stick
The Auxtek-T003 HDMI stick is an A10s based HDMI stick with USB wifi,
and composite video out support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Wed, 19 Aug 2015 08:57:22 +0000 (16:57 +0800)]
ARM: dts: sun6i: hummingbird: Add missing pinmux setting for gmac phy reset
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Ralph Benadski [Fri, 14 Aug 2015 14:44:36 +0000 (16:44 +0200)]
ARM: dts: sun7i: Enable USB DRC on cubieboard2
Enable the otg/drc usb controller on the cubieboard2.
Note this board has the otg-vbus connected directly to the 5v-dcc of
the board, so there is no vbus0 regulator, nor vbus0-det.
Signed-off-by: Ralph Benadski <benadski@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Jelle van der Waa [Fri, 14 Aug 2015 14:44:35 +0000 (16:44 +0200)]
ARM: dts: sun7i: Enable USB DRC on pcDuino 3
Enable the otg/drc usb controller on the pcDuino 3.
Note this board has the otg-vbus connected directly to the 5v-dcc of
the board, so there is no vbus0 regulator, nor vbus0-det.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Fri, 14 Aug 2015 14:44:37 +0000 (16:44 +0200)]
ARM: dts: sun8i: Add support for qt90h-v4 tablets
The gt90h is a pcb found in generic 9" tablets with an A23 soc, 1G RAM
and 8G nand, rtl8723as usb wifi, 1 micro usb port and 1 micro sd slot.
This commit adds a dts for v4 of the gt90h pcb.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Jelle van der Waa [Fri, 14 Aug 2015 14:44:34 +0000 (16:44 +0200)]
ARM: dts: sun7i: Add regulator configuration to the pcduino3 dts file
Add regulator configuration to the pcduino3 dts file.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Removed usb_power_supply node that isn't defined in the DTSI]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Fri, 14 Aug 2015 14:44:32 +0000 (16:44 +0200)]
ARM: dts: sun5i: Add simplefb node for tvencoder output
Add a simplefb node for tvencoder / composite-video output, such as found
on the Auxtek-T003 and the CHIP.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Fri, 7 Aug 2015 15:22:35 +0000 (17:22 +0200)]
ARM: dts: sun6i: Columbus: Add i2c controller for communicating with the LCD
The Colombus development kit uses an optional 2048x1536 edp panel using
an anx9804 parallel lcd to edp converter. The anx9804 chip is controlled
via an i2c bus which is connected to 2 regular gpio pins.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Olliver Schinagl [Sun, 9 Aug 2015 18:22:58 +0000 (20:22 +0200)]
ARM: dts: sunxi: enable otg port on the sun7i-a20-olinuxino-lime2
This patch enables the musb-otg USB controller on the Lime2. The Lime2
differs from the Lime1 series in pins used for usb0 power.
Tested on a OlinuXino Lime2-4GB.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
projects / platform / kernel / linux-exynos.git / log