drm/nouveau/tmr: fix corruption of the pending list when rescheduling an alarm

commit 9fc64667ee48c9a25e7dca1a6bcb6906fec5bcc5 upstream.

At least therm/fantog "attempts" to work around this issue, which could
lead to corruption of the pending alarm list.

Fix it properly by not updating the timestamp without the lock held, or
trying to add an already pending alarm to the pending alarm list....

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/nouveau/tmr: ack interrupt before processing alarms

commit 3733bd8b407211739e72d051e5f30ad82a52c4bc upstream.

Fixes a race where we can miss an alarm that triggers while we're already
processing previous alarms.

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/nouveau/therm: remove ineffective workarounds for alarm bugs

commit e4311ee51d1e2676001b2d8fcefd92bdd79aad85 upstream.

These were ineffective due to touching the list without the alarm lock,
but should no longer be required.

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: Add missing lb_vblank_lead_lines setup to DCE-6 path.

commit effaf848b957fbf72a3b6a1ad87f5e031eda0b75 upstream.

This apparently got lost when implementing the new DCE-6 support
and would cause failures in pageflip scheduling and timestamping.

Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: Avoid overflows/divide-by-zero in latency_watermark calculations.

commit e190ed1ea7458e446230de4113cc5d53b8dc4ec8 upstream.

At dot clocks > approx. 250 Mhz, some of these calcs will overflow and
cause miscalculation of latency watermarks, and for some overflows also
divide-by-zero driver crash ("divide error: 0000 [#1] PREEMPT SMP" in
"dce_v10_0_latency_watermark+0x12d/0x190").

This zero-divide happened, e.g., on AMD Tonga Pro under DCE-10,
on a Displayport panel when trying to set a video mode of 2560x1440
at 165 Hz vrefresh with a dot clock of 635.540 Mhz.

Refine calculations to avoid the overflows.

Tested for DCE-10 with R9 380 Tonga + ASUS ROG PG279 panel.

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: Make display watermark calculations more accurate

commit d63c277dc672e0c568481af043359420fa9d4736 upstream.

Avoid big roundoff errors in scanline/hactive durations for
high pixel clocks, especially for >= 500 Mhz, and thereby
program more accurate display fifo watermarks.

Implemented here for DCE 6,8,10,11.
Successfully tested on DCE 10 with AMD R9 380 Tonga.

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ath9k_htc: fix NULL-deref at probe

commit ebeb36670ecac36c179b5fb5d5c88ff03ba191ec upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.

Fixes: 36bcce430657 ("ath9k_htc: Handle storage devices")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ath9k_htc: Add support of AirTies 1eda:2315 AR9271 device

commit 16ff1fb0e32f76a5d285a6f23b82d21aa52813c6 upstream.

T:  Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#=  7 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs=  1
P:  Vendor=1eda ProdID=2315 Rev=01.08
S:  Manufacturer=ATHEROS
S:  Product=USB2.0 WLAN
S:  SerialNumber=12345
C:  #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 6 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/cputime: fix incorrect system time

commit 07a63cbe8bcb6ba72fb989dcab1ec55ec6c36c7e upstream.

git commit c5328901aa1db134 "[S390] entry[64].S improvements" removed
the update of the exit_timer lowcore field from the critical section
cleanup of the .Lsysc_restore/.Lsysc_done and .Lio_restore/.Lio_done
blocks. If the PSW is updated by the critical section cleanup to point to
user space again, the interrupt entry code will do a vtime calculation
after the cleanup completed with an exit_timer value which has *not* been
updated. Due to this incorrect system time deltas are calculated.

If an interrupt occured with an old PSW between .Lsysc_restore/.Lsysc_done
or .Lio_restore/.Lio_done update __LC_EXIT_TIMER with the system entry
time of the interrupt.

Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/kdump: Add final note

commit dcc00b79fc3d076832f7240de8870f492629b171 upstream.

Since linux v3.14 with commit 38dfac843cb6d7be1 ("vmcore: prevent PT_NOTE
p_memsz overflow during header update") on s390 we get the following
message in the kdump kernel:

  Warning: Exceeded p_memsz, dropping PT_NOTE entry n_namesz=0x6b6b6b6b,
  n_descsz=0x6b6b6b6b

The reason for this is that we don't create a final zero note in
the ELF header which the proc/vmcore code uses to find out the end
of the notes section (see also kernel/kexec_core.c:final_note()).

It still worked on s390 by chance because we (most of the time?) have the
byte pattern 0x6b6b6b6b after the notes section which also makes the notes
parsing code stop in update_note_header_size_elf64() because 0x6b6b6b6b is
interpreded as note size:

  if ((real_sz + sz) > max_sz) {
          pr_warn("Warning: Exceeded p_memsz, dropping P ...);
          break;
  }

So fix this and add the missing final note to the ELF header.
We don't have to adjust the memory size for ELF header ("alloc_size")
because the new ELF note still fits into the 0x1000 base memory.

Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

regulator: tps65023: Fix inverted core enable logic.

commit c90722b54a4f5e21ac59301ed9a6dbaa439bdb16 upstream.

Commit 43530b69d758328d3ffe6ab98fd640463e8e3667 ("regulator: Use
regmap_read/write(), regmap_update_bits functions directly") intended
to replace working inline helper functions with standard regmap
calls.  However, it also inverted the set/clear logic of the "CORE ADJ
Allowed" bit.  That patch was clearly never tested, since without that
bit cleared, the core VDCDC1 voltage output does not react to I2C
configuration changes.

This patch fixes the issue by clearing the bit as in the original,
correct implementation.  Note for stable back porting that, due to
subsequent driver churn, this patch will not apply on every kernel
version.

Fixes: 43530b69d758 ("regulator: Use regmap_read/write(), regmap_update_bits functions directly")
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

regulator: rk808: Fix RK818 LDO2

commit 75f88115391156b3f0fecbbae76bf870c89bcab8 upstream.

Set the correct voltage select register for LDO2.

Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86: fix 32-bit case of __get_user_asm_u64()

commit 33c9e9729033387ef0521324c62e7eba529294af upstream.

The code to fetch a 64-bit value from user space was entirely buggered,
and has been since the code was merged in early 2016 in commit
b2f680380ddf ("x86/mm/32: Add support for 64-bit __get_user() on 32-bit
kernels").

Happily the buggered routine is almost certainly entirely unused, since
the normal way to access user space memory is just with the non-inlined
"get_user()", and the inlined version didn't even historically exist.

The normal "get_user()" case is handled by external hand-written asm in
arch/x86/lib/getuser.S that doesn't have either of these issues.

There were two independent bugs in __get_user_asm_u64():

 - it still did the STAC/CLAC user space access marking, even though
   that is now done by the wrapper macros, see commit 11f1a4b9755f
   ("x86: reorganize SMAP handling in user space accesses").

   This didn't result in a semantic error, it just means that the
   inlined optimized version was hugely less efficient than the
   allegedly slower standard version, since the CLAC/STAC overhead is
   quite high on modern Intel CPU's.

 - the double register %eax/%edx was marked as an output, but the %eax
   part of it was touched early in the asm, and could thus clobber other
   inputs to the asm that gcc didn't expect it to touch.

   In particular, that meant that the generated code could look like
   this:

        mov    (%eax),%eax
        mov    0x4(%eax),%edx

   where the load of %edx obviously was _supposed_ to be from the 32-bit
   word that followed the source of %eax, but because %eax was
   overwritten by the first instruction, the source of %edx was
   basically random garbage.

The fixes are trivial: remove the extraneous STAC/CLAC entries, and mark
the 64-bit output as early-clobber to let gcc know that no inputs should
alias with the output register.

Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: X86: Fix read out-of-bounds vulnerability in kvm pio emulation

commit cbfc6c9184ce71b52df4b1d82af5afc81a709178 upstream.

Huawei folks reported a read out-of-bounds vulnerability in kvm pio emulation.

- "inb" instruction to access PIT Mod/Command register (ioport 0x43, write only,
  a read should be ignored) in guest can get a random number.
- "rep insb" instruction to access PIT register port 0x43 can control memcpy()
  in emulator_pio_in_emulated() to copy max 0x400 bytes but only read 1 bytes,
  which will disclose the unimportant kernel memory in host but no crash.

The similar test program below can reproduce the read out-of-bounds vulnerability:

void hexdump(void *mem, unsigned int len)
{
        unsigned int i, j;

        for(i = 0; i < len + ((len % HEXDUMP_COLS) ? (HEXDUMP_COLS - len % HEXDUMP_COLS) : 0); i++)
        {
                /* print offset */
                if(i % HEXDUMP_COLS == 0)
                {
                        printf("0x%06x: ", i);
                }

                /* print hex data */
                if(i < len)
                {
                        printf("%02x ", 0xFF & ((char*)mem)[i]);
                }
                else /* end of block, just aligning for ASCII dump */
                {
                        printf("   ");
                }

                /* print ASCII dump */
                if(i % HEXDUMP_COLS == (HEXDUMP_COLS - 1))
                {
                        for(j = i - (HEXDUMP_COLS - 1); j <= i; j++)
                        {
                                if(j >= len) /* end of block, not really printing */
                                {
                                        putchar(' ');
                                }
                                else if(isprint(((char*)mem)[j])) /* printable char */
                                {
                                        putchar(0xFF & ((char*)mem)[j]);
                                }
                                else /* other char */
                                {
                                        putchar('.');
                                }
                        }
                        putchar('\n');
                }
        }
}

int main(void)
{
int i;
if (iopl(3))
{
err(1, "set iopl unsuccessfully\n");
return -1;
}
static char buf[0x40];

/* test ioport 0x40,0x41,0x42,0x43,0x44,0x45 */

memset(buf, 0xab, sizeof(buf));

asm volatile("push %rdi;");
asm volatile("mov %0, %%rdi;"::"q"(buf));

asm volatile ("mov $0x40, %rdx;");
asm volatile ("in %dx,%al;");
asm volatile ("stosb;");

asm volatile ("mov $0x41, %rdx;");
asm volatile ("in %dx,%al;");
asm volatile ("stosb;");

asm volatile ("mov $0x42, %rdx;");
asm volatile ("in %dx,%al;");
asm volatile ("stosb;");

asm volatile ("mov $0x43, %rdx;");
asm volatile ("in %dx,%al;");
asm volatile ("stosb;");

asm volatile ("mov $0x44, %rdx;");
asm volatile ("in %dx,%al;");
asm volatile ("stosb;");

asm volatile ("mov $0x45, %rdx;");
asm volatile ("in %dx,%al;");
asm volatile ("stosb;");

asm volatile ("pop %rdi;");
hexdump(buf, 0x40);

printf("\n");

/* ins port 0x40 */

memset(buf, 0xab, sizeof(buf));

asm volatile("push %rdi;");
asm volatile("mov %0, %%rdi;"::"q"(buf));

asm volatile ("mov $0x20, %rcx;");
asm volatile ("mov $0x40, %rdx;");
asm volatile ("rep insb;");

asm volatile ("pop %rdi;");
hexdump(buf, 0x40);

printf("\n");

/* ins port 0x43 */

memset(buf, 0xab, sizeof(buf));

asm volatile("push %rdi;");
asm volatile("mov %0, %%rdi;"::"q"(buf));

asm volatile ("mov $0x20, %rcx;");
asm volatile ("mov $0x43, %rdx;");
asm volatile ("rep insb;");

asm volatile ("pop %rdi;");
hexdump(buf, 0x40);

printf("\n");
return 0;
}

The vcpu->arch.pio_data buffer is used by both in/out instrutions emulation
w/o clear after using which results in some random datas are left over in
the buffer. Guest reads port 0x43 will be ignored since it is write only,
however, the function kernel_pio() can't distigush this ignore from successfully
reads data from device's ioport. There is no new data fill the buffer from
port 0x43, however, emulator_pio_in_emulated() will copy the stale data in
the buffer to the guest unconditionally. This patch fixes it by clearing the
buffer before in instruction emulation to avoid to grant guest the stale data
in the buffer.

In addition, string I/O is not supported for in kernel device. So there is no
iteration to read ioport %RCX times for string I/O. The function kernel_pio()
just reads one round, and then copy the io size * %RCX to the guest unconditionally,
actually it copies the one round ioport data w/ other random datas which are left
over in the vcpu->arch.pio_data buffer to the guest. This patch fixes it by
introducing the string I/O support for in kernel device in order to grant the right
ioport datas to the guest.

Before the patch:

0x000000: fe 38 93 93 ff ff ab ab .8......
0x000008: ab ab ab ab ab ab ab ab ........
0x000010: ab ab ab ab ab ab ab ab ........
0x000018: ab ab ab ab ab ab ab ab ........
0x000020: ab ab ab ab ab ab ab ab ........
0x000028: ab ab ab ab ab ab ab ab ........
0x000030: ab ab ab ab ab ab ab ab ........
0x000038: ab ab ab ab ab ab ab ab ........

0x000000: f6 00 00 00 00 00 00 00 ........
0x000008: 00 00 00 00 00 00 00 00 ........
0x000010: 00 00 00 00 4d 51 30 30 ....MQ00
0x000018: 30 30 20 33 20 20 20 20 00 3
0x000020: ab ab ab ab ab ab ab ab ........
0x000028: ab ab ab ab ab ab ab ab ........
0x000030: ab ab ab ab ab ab ab ab ........
0x000038: ab ab ab ab ab ab ab ab ........

0x000000: f6 00 00 00 00 00 00 00 ........
0x000008: 00 00 00 00 00 00 00 00 ........
0x000010: 00 00 00 00 4d 51 30 30 ....MQ00
0x000018: 30 30 20 33 20 20 20 20 00 3
0x000020: ab ab ab ab ab ab ab ab ........
0x000028: ab ab ab ab ab ab ab ab ........
0x000030: ab ab ab ab ab ab ab ab ........
0x000038: ab ab ab ab ab ab ab ab ........

After the patch:

0x000000: 1e 02 f8 00 ff ff ab ab ........
0x000008: ab ab ab ab ab ab ab ab ........
0x000010: ab ab ab ab ab ab ab ab ........
0x000018: ab ab ab ab ab ab ab ab ........
0x000020: ab ab ab ab ab ab ab ab ........
0x000028: ab ab ab ab ab ab ab ab ........
0x000030: ab ab ab ab ab ab ab ab ........
0x000038: ab ab ab ab ab ab ab ab ........

0x000000: d2 e2 d2 df d2 db d2 d7 ........
0x000008: d2 d3 d2 cf d2 cb d2 c7 ........
0x000010: d2 c4 d2 c0 d2 bc d2 b8 ........
0x000018: d2 b4 d2 b0 d2 ac d2 a8 ........
0x000020: ab ab ab ab ab ab ab ab ........
0x000028: ab ab ab ab ab ab ab ab ........
0x000030: ab ab ab ab ab ab ab ab ........
0x000038: ab ab ab ab ab ab ab ab ........

0x000000: 00 00 00 00 00 00 00 00 ........
0x000008: 00 00 00 00 00 00 00 00 ........
0x000010: 00 00 00 00 00 00 00 00 ........
0x000018: 00 00 00 00 00 00 00 00 ........
0x000020: ab ab ab ab ab ab ab ab ........
0x000028: ab ab ab ab ab ab ab ab ........
0x000030: ab ab ab ab ab ab ab ab ........
0x000038: ab ab ab ab ab ab ab ab ........

Reported-by: Moguofang <moguofang@huawei.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Moguofang <moguofang@huawei.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: Fix potential preemption when get the current kvmclock timestamp

commit e2c2206a18993bc9f62393d49c7b2066c3845b25 upstream.

 BUG: using __this_cpu_read() in preemptible [00000000] code: qemu-system-x86/2809
 caller is __this_cpu_preempt_check+0x13/0x20
 CPU: 2 PID: 2809 Comm: qemu-system-x86 Not tainted 4.11.0+ #13
 Call Trace:
  dump_stack+0x99/0xce
  check_preemption_disabled+0xf5/0x100
  __this_cpu_preempt_check+0x13/0x20
  get_kvmclock_ns+0x6f/0x110 [kvm]
  get_time_ref_counter+0x5d/0x80 [kvm]
  kvm_hv_process_stimers+0x2a1/0x8a0 [kvm]
  ? kvm_hv_process_stimers+0x2a1/0x8a0 [kvm]
  ? kvm_arch_vcpu_ioctl_run+0xac9/0x1ce0 [kvm]
  kvm_arch_vcpu_ioctl_run+0x5bf/0x1ce0 [kvm]
  kvm_vcpu_ioctl+0x384/0x7b0 [kvm]
  ? kvm_vcpu_ioctl+0x384/0x7b0 [kvm]
  ? __fget+0xf3/0x210
  do_vfs_ioctl+0xa4/0x700
  ? __fget+0x114/0x210
  SyS_ioctl+0x79/0x90
  entry_SYSCALL_64_fastpath+0x23/0xc2
 RIP: 0033:0x7f9d164ed357
  ? __this_cpu_preempt_check+0x13/0x20

This can be reproduced by run kvm-unit-tests/hyperv_stimer.flat w/
CONFIG_PREEMPT and CONFIG_DEBUG_PREEMPT enabled.

Safe access to per-CPU data requires a couple of constraints, though: the
thread working with the data cannot be preempted and it cannot be migrated
while it manipulates per-CPU variables. If the thread is preempted, the
thread that replaces it could try to work with the same variables; migration
to another CPU could also cause confusion. However there is no preemption
disable when reads host per-CPU tsc rate to calculate the current kvmclock
timestamp.

This patch fixes it by utilizing get_cpu/put_cpu pair to guarantee both
__this_cpu_read() and rdtsc() are not preempted.

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: Fix load damaged SSEx MXCSR register

commit a575813bfe4bc15aba511a5e91e61d242bff8b9d upstream.

Reported by syzkaller:

   BUG: unable to handle kernel paging request at ffffffffc07f6a2e
   IP: report_bug+0x94/0x120
   PGD 348e12067
   P4D 348e12067
   PUD 348e14067
   PMD 3cbd84067
   PTE 80000003f7e87161

   Oops: 0003 [#1] SMP
   CPU: 2 PID: 7091 Comm: kvm_load_guest_ Tainted: G           OE   4.11.0+ #8
   task: ffff92fdfb525400 task.stack: ffffbda6c3d04000
   RIP: 0010:report_bug+0x94/0x120
   RSP: 0018:ffffbda6c3d07b20 EFLAGS: 00010202
    do_trap+0x156/0x170
    do_error_trap+0xa3/0x170
    ? kvm_load_guest_fpu.part.175+0x12a/0x170 [kvm]
    ? mark_held_locks+0x79/0xa0
    ? retint_kernel+0x10/0x10
    ? trace_hardirqs_off_thunk+0x1a/0x1c
    do_invalid_op+0x20/0x30
    invalid_op+0x1e/0x30
   RIP: 0010:kvm_load_guest_fpu.part.175+0x12a/0x170 [kvm]
    ? kvm_load_guest_fpu.part.175+0x1c/0x170 [kvm]
    kvm_arch_vcpu_ioctl_run+0xed6/0x1b70 [kvm]
    kvm_vcpu_ioctl+0x384/0x780 [kvm]
    ? kvm_vcpu_ioctl+0x384/0x780 [kvm]
    ? sched_clock+0x13/0x20
    ? __do_page_fault+0x2a0/0x550
    do_vfs_ioctl+0xa4/0x700
    ? up_read+0x1f/0x40
    ? __do_page_fault+0x2a0/0x550
    SyS_ioctl+0x79/0x90
    entry_SYSCALL_64_fastpath+0x23/0xc2

SDM mentioned that "The MXCSR has several reserved bits, and attempting to write
a 1 to any of these bits will cause a general-protection exception(#GP) to be
generated". The syzkaller forks' testcase overrides xsave area w/ random values
and steps on the reserved bits of MXCSR register. The damaged MXCSR register
values of guest will be restored to SSEx MXCSR register before vmentry. This
patch fixes it by catching userspace override MXCSR register reserved bits w/
random values and bails out immediately.

Reported-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ima: accept previously set IMA_NEW_FILE

commit 1ac202e978e18f045006d75bd549612620c6ec3a upstream.

Modifying the attributes of a file makes ima_inode_post_setattr reset
the IMA cache flags. So if the file, which has just been created,
is opened a second time before the first file descriptor is closed,
verification fails since the security.ima xattr has not been written
yet. We therefore have to look at the IMA_NEW_FILE even if the file
already existed.

With this patch there should no longer be an error when cat tries to
open testfile:

$ rm -f testfile
$ ( echo test >&3 ; touch testfile ; cat testfile ) 3>testfile

A file being new is no reason to accept that it is missing a digital
signature demanded by the policy.

Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mwifiex: pcie: fix cmd_buf use-after-free in remove/reset

commit 3c8cb9ad032d737b874e402c59eb51e3c991a144 upstream.

Command buffers (skb's) are allocated by the main driver, and freed upon
the last use. That last use is often in mwifiex_free_cmd_buffer(). In
the meantime, if the command buffer gets used by the PCI driver, we map
it as DMA-able, and store the mapping information in the 'cb' memory.

However, if a command was in-flight when resetting the device (and
therefore was still mapped), we don't get a chance to unmap this memory
until after the core has cleaned up its command handling.

Let's keep a refcount within the PCI driver, so we ensure the memory
only gets freed after we've finished unmapping it.

Noticed by KASAN when forcing a reset via:

  echo 1 > /sys/bus/pci/.../reset

The same code path can presumably be exercised in remove() and
shutdown().

[  205.390377] mwifiex_pcie 0000:01:00.0: info: shutdown mwifiex...
[  205.400393] ==================================================================
[  205.407719] BUG: KASAN: use-after-free in mwifiex_unmap_pci_memory.isra.14+0x4c/0x100 [mwifiex_pcie] at addr ffffffc0ad471b28
[  205.419040] Read of size 16 by task bash/1913
[  205.423421] =============================================================================
[  205.431625] BUG skbuff_head_cache (Tainted: G    B          ): kasan: bad access detected
[  205.439815] -----------------------------------------------------------------------------
[  205.439815]
[  205.449534] INFO: Allocated in __build_skb+0x48/0x114 age=1311 cpu=4 pid=1913
[  205.456709]  alloc_debug_processing+0x124/0x178
[  205.461282]  ___slab_alloc.constprop.58+0x528/0x608
[  205.466196]  __slab_alloc.isra.54.constprop.57+0x44/0x54
[  205.471542]  kmem_cache_alloc+0xcc/0x278
[  205.475497]  __build_skb+0x48/0x114
[  205.479019]  __netdev_alloc_skb+0xe0/0x170
[  205.483244]  mwifiex_alloc_cmd_buffer+0x68/0xdc [mwifiex]
[  205.488759]  mwifiex_init_fw+0x40/0x6cc [mwifiex]
[  205.493584]  _mwifiex_fw_dpc+0x158/0x520 [mwifiex]
[  205.498491]  mwifiex_reinit_sw+0x2c4/0x398 [mwifiex]
[  205.503510]  mwifiex_pcie_reset_notify+0x114/0x15c [mwifiex_pcie]
[  205.509643]  pci_reset_notify+0x5c/0x6c
[  205.513519]  pci_reset_function+0x6c/0x7c
[  205.517567]  reset_store+0x68/0x98
[  205.521003]  dev_attr_store+0x54/0x60
[  205.524705]  sysfs_kf_write+0x9c/0xb0
[  205.528413] INFO: Freed in __kfree_skb+0xb0/0xbc age=131 cpu=4 pid=1913
[  205.535064]  free_debug_processing+0x264/0x370
[  205.539550]  __slab_free+0x84/0x40c
[  205.543075]  kmem_cache_free+0x1c8/0x2a0
[  205.547030]  __kfree_skb+0xb0/0xbc
[  205.550465]  consume_skb+0x164/0x178
[  205.554079]  __dev_kfree_skb_any+0x58/0x64
[  205.558304]  mwifiex_free_cmd_buffer+0xa0/0x158 [mwifiex]
[  205.563817]  mwifiex_shutdown_drv+0x578/0x5c4 [mwifiex]
[  205.569164]  mwifiex_shutdown_sw+0x178/0x310 [mwifiex]
[  205.574353]  mwifiex_pcie_reset_notify+0xd4/0x15c [mwifiex_pcie]
[  205.580398]  pci_reset_notify+0x5c/0x6c
[  205.584274]  pci_dev_save_and_disable+0x24/0x6c
[  205.588837]  pci_reset_function+0x30/0x7c
[  205.592885]  reset_store+0x68/0x98
[  205.596324]  dev_attr_store+0x54/0x60
[  205.600017]  sysfs_kf_write+0x9c/0xb0
...
[  205.800488] Call trace:
[  205.802980] [<ffffffc00020a69c>] dump_backtrace+0x0/0x190
[  205.808415] [<ffffffc00020a96c>] show_stack+0x20/0x28
[  205.813506] [<ffffffc0005d020c>] dump_stack+0xa4/0xcc
[  205.818598] [<ffffffc0003be44c>] print_trailer+0x158/0x168
[  205.824120] [<ffffffc0003be5f0>] object_err+0x4c/0x5c
[  205.829210] [<ffffffc0003c45bc>] kasan_report+0x334/0x500
[  205.834641] [<ffffffc0003c3994>] check_memory_region+0x20/0x14c
[  205.840593] [<ffffffc0003c3b14>] __asan_loadN+0x14/0x1c
[  205.845879] [<ffffffbffc46171c>] mwifiex_unmap_pci_memory.isra.14+0x4c/0x100 [mwifiex_pcie]
[  205.854282] [<ffffffbffc461864>] mwifiex_pcie_delete_cmdrsp_buf+0x94/0xa8 [mwifiex_pcie]
[  205.862421] [<ffffffbffc462028>] mwifiex_pcie_free_buffers+0x11c/0x158 [mwifiex_pcie]
[  205.870302] [<ffffffbffc4620d4>] mwifiex_pcie_down_dev+0x70/0x80 [mwifiex_pcie]
[  205.877736] [<ffffffbffc1397a8>] mwifiex_shutdown_sw+0x190/0x310 [mwifiex]
[  205.884658] [<ffffffbffc4606b4>] mwifiex_pcie_reset_notify+0xd4/0x15c [mwifiex_pcie]
[  205.892446] [<ffffffc000635f54>] pci_reset_notify+0x5c/0x6c
[  205.898048] [<ffffffc00063a044>] pci_dev_save_and_disable+0x24/0x6c
[  205.904350] [<ffffffc00063cf0c>] pci_reset_function+0x30/0x7c
[  205.910134] [<ffffffc000641118>] reset_store+0x68/0x98
[  205.915312] [<ffffffc000771588>] dev_attr_store+0x54/0x60
[  205.920750] [<ffffffc00046f53c>] sysfs_kf_write+0x9c/0xb0
[  205.926182] [<ffffffc00046dfb0>] kernfs_fop_write+0x184/0x1f8
[  205.931963] [<ffffffc0003d64f4>] __vfs_write+0x6c/0x17c
[  205.937221] [<ffffffc0003d7164>] vfs_write+0xf0/0x1c4
[  205.942310] [<ffffffc0003d7da0>] SyS_write+0x78/0xd8
[  205.947312] [<ffffffc000204634>] el0_svc_naked+0x24/0x28
...
[  205.998268] ==================================================================

This bug has been around in different forms for a while. It was sort of
noticed in commit 955ab095c51a ("mwifiex: Do not kfree cmd buf while
unregistering PCIe"), but it just fixed the double-free, without
acknowledging the potential for use-after-free.

Fixes: fc3314609047 ("mwifiex: use pci_alloc/free_consistent APIs for PCIe")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mwifiex: MAC randomization should not be persistent

commit 7e2f18f06408ff56d7f75e68de8064777137b319 upstream.

nl80211 provides the NL80211_SCAN_FLAG_RANDOM_ADDR for every scan
request that should be randomized; the absence of such a flag means we
should not randomize. However, mwifiex was stashing the latest
randomization request and *always* using it for future scans, even those
that didn't set the flag.

Let's zero out the randomization info whenever we get a scan request
without NL80211_SCAN_FLAG_RANDOM_ADDR. I'd prefer to remove
priv->random_mac entirely (and plumb the randomization MAC properly
through the call sequence), but the spaghetti is a little difficult to
unravel here for me.

Fixes: c2a8f0ff9c6c ("mwifiex: support random MAC address for scanning")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8821ae: setup 8812ae RFE according to device type

commit 46cfa2148e7371c537efff1a1c693e58f523089d upstream.

Current channel switch implementation sets 8812ae RFE reg value assuming
that device always has type 2.

Extend possible RFE types set and write corresponding reg values.

Source for new code is
http://dlcdnet.asus.com/pub/ASUS/wireless/PCE-AC51/DR_PCE_AC51_20232801152016.zip

Signed-off-by: Maxim Samoylov <max7255@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md: MD_CLOSING needs to be cleared after called md_set_readonly or do_md_stop

commit 065e519e71b2c1f41936cce75b46b5ab34adb588 upstream.

if called md_set_readonly and set MD_CLOSING bit, the mddev cannot
be opened any more due to the MD_CLOING bit wasn't cleared. Thus it
needs to be cleared in md_ioctl after any call to md_set_readonly()
or do_md_stop().

Signed-off-by: NeilBrown <neilb@suse.com>
Fixes: af8d8e6f0315 ("md: changes for MD_STILL_CLOSED flag")
Signed-off-by: Zhilong Liu <zlliu@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md: update slab_cache before releasing new stripes when stripes resizing

commit 583da48e388f472e8818d9bb60ef6a1d40ee9f9d upstream.

When growing raid5 device on machine with small memory, there is chance that
mdadm will be killed and the following bug report can be observed. The same
bug could also be reproduced in linux-4.10.6.

[57600.075774] BUG: unable to handle kernel NULL pointer dereference at           (null)
[57600.083796] IP: [<ffffffff81a6aa87>] _raw_spin_lock+0x7/0x20
[57600.110378] PGD 421cf067 PUD 4442d067 PMD 0
[57600.114678] Oops: 0002 [#1] SMP
[57600.180799] CPU: 1 PID: 25990 Comm: mdadm Tainted: P           O    4.2.8 #1
[57600.187849] Hardware name: To be filled by O.E.M. To be filled by O.E.M./MAHOBAY, BIOS QV05AR66 03/06/2013
[57600.197490] task: ffff880044e47240 ti: ffff880043070000 task.ti: ffff880043070000
[57600.204963] RIP: 0010:[<ffffffff81a6aa87>]  [<ffffffff81a6aa87>] _raw_spin_lock+0x7/0x20
[57600.213057] RSP: 0018:ffff880043073810  EFLAGS: 00010046
[57600.218359] RAX: 0000000000000000 RBX: 000000000000000c RCX: ffff88011e296dd0
[57600.225486] RDX: 0000000000000001 RSI: ffffe8ffffcb46c0 RDI: 0000000000000000
[57600.232613] RBP: ffff880043073878 R08: ffff88011e5f8170 R09: 0000000000000282
[57600.239739] R10: 0000000000000005 R11: 28f5c28f5c28f5c3 R12: ffff880043073838
[57600.246872] R13: ffffe8ffffcb46c0 R14: 0000000000000000 R15: ffff8800b9706a00
[57600.253999] FS:  00007f576106c700(0000) GS:ffff88011e280000(0000) knlGS:0000000000000000
[57600.262078] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[57600.267817] CR2: 0000000000000000 CR3: 00000000428fe000 CR4: 00000000001406e0
[57600.274942] Stack:
[57600.276949]  ffffffff8114ee35 ffff880043073868 0000000000000282 000000000000eb3f
[57600.284383]  ffffffff81119043 ffff880043073838 ffff880043073838 ffff88003e197b98
[57600.291820]  ffffe8ffffcb46c0 ffff88003e197360 0000000000000286 ffff880043073968
[57600.299254] Call Trace:
[57600.301698]  [<ffffffff8114ee35>] ? cache_flusharray+0x35/0xe0
[57600.307523]  [<ffffffff81119043>] ? __page_cache_release+0x23/0x110
[57600.313779]  [<ffffffff8114eb53>] kmem_cache_free+0x63/0xc0
[57600.319344]  [<ffffffff81579942>] drop_one_stripe+0x62/0x90
[57600.324915]  [<ffffffff81579b5b>] raid5_cache_scan+0x8b/0xb0
[57600.330563]  [<ffffffff8111b98a>] shrink_slab.part.36+0x19a/0x250
[57600.336650]  [<ffffffff8111e38c>] shrink_zone+0x23c/0x250
[57600.342039]  [<ffffffff8111e4f3>] do_try_to_free_pages+0x153/0x420
[57600.348210]  [<ffffffff8111e851>] try_to_free_pages+0x91/0xa0
[57600.353959]  [<ffffffff811145b1>] __alloc_pages_nodemask+0x4d1/0x8b0
[57600.360303]  [<ffffffff8157a30b>] check_reshape+0x62b/0x770
[57600.365866]  [<ffffffff8157a4a5>] raid5_check_reshape+0x55/0xa0
[57600.371778]  [<ffffffff81583df7>] update_raid_disks+0xc7/0x110
[57600.377604]  [<ffffffff81592b73>] md_ioctl+0xd83/0x1b10
[57600.382827]  [<ffffffff81385380>] blkdev_ioctl+0x170/0x690
[57600.388307]  [<ffffffff81195238>] block_ioctl+0x38/0x40
[57600.393525]  [<ffffffff811731c5>] do_vfs_ioctl+0x2b5/0x480
[57600.399010]  [<ffffffff8115e07b>] ? vfs_write+0x14b/0x1f0
[57600.404400]  [<ffffffff811733cc>] SyS_ioctl+0x3c/0x70
[57600.409447]  [<ffffffff81a6ad97>] entry_SYSCALL_64_fastpath+0x12/0x6a
[57600.415875] Code: 00 00 00 00 55 48 89 e5 8b 07 85 c0 74 04 31 c0 5d c3 ba 01 00 00 00 f0 0f b1 17 85 c0 75 ef b0 01 5d c3 90 31 c0 ba 01 00 00 00 <f0> 0f b1 17 85 c0 75 01 c3 55 89 c6 48 89 e5 e8 85 d1 63 ff 5d
[57600.435460] RIP  [<ffffffff81a6aa87>] _raw_spin_lock+0x7/0x20
[57600.441208]  RSP <ffff880043073810>
[57600.444690] CR2: 0000000000000000
[57600.448000] ---[ end trace cbc6b5cc4bf9831d ]---

The problem is that resize_stripes() releases new stripe_heads before assigning new
slab cache to conf->slab_cache. If the shrinker function raid5_cache_scan() gets called
after resize_stripes() starting releasing new stripes but right before new slab cache
being assigned, it is possible that these new stripe_heads will be freed with the old
slab_cache which was already been destoryed and that triggers this bug.

Signed-off-by: Dennis Yang <dennisyang@qnap.com>
Fixes: edbe83ab4c27 ("md/raid5: allow the stripe_cache to grow and shrink.")
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm space map disk: fix some book keeping in the disk space map

commit 0377a07c7a035e0d033cd8b29f0cb15244c0916a upstream.

When decrementing the reference count for a block, the free count wasn't
being updated if the reference count went to zero.

Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm thin metadata: call precommit before saving the roots

commit 91bcdb92d39711d1adb40c26b653b7978d93eb98 upstream.

These calls were the wrong way round in __write_initial_superblock.

Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm bufio: make the parameter "retain_bytes" unsigned long

commit 13840d38016203f0095cd547b90352812d24b787 upstream.

Change the type of the parameter "retain_bytes" from unsigned to
unsigned long, so that on 64-bit machines the user can set more than
4GiB of data to be retained.

Also, change the type of the variable "count" in the function
"__evict_old_buffers" to unsigned long.  The assignment
"count = c->n_buffers[LIST_CLEAN] + c->n_buffers[LIST_DIRTY];"
could result in unsigned long to unsigned overflow and that could result
in buffers not being freed when they should.

While at it, avoid division in get_retain_buffers().  Division is slow,
we can change it to shift because we have precalculated the log2 of
block size.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm cache metadata: fail operations if fail_io mode has been established

commit 10add84e276432d9dd8044679a1028dd4084117e upstream.

Otherwise it is possible to trigger crashes due to the metadata being
inaccessible yet these methods don't safely account for that possibility
without these checks.

Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm mpath: split and rename activate_path() to prepare for its expanded use

commit 89bfce763e43fa4897e0d3af6b29ed909df64cfd upstream.

activate_path() is renamed to activate_path_work() which now calls
activate_or_offline_path().  activate_or_offline_path() will be used
by the next commit.

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm bufio: check new buffer allocation watermark every 30 seconds

commit 390020ad2af9ca04844c4f3b1f299ad8746d84c8 upstream.

dm-bufio checks a watermark when it allocates a new buffer in
__bufio_new().  However, it doesn't check the watermark when the user
changes /sys/module/dm_bufio/parameters/max_cache_size_bytes.

This may result in a problem - if the watermark is high enough so that
all possible buffers are allocated and if the user lowers the value of
"max_cache_size_bytes", the watermark will never be checked against the
new value because no new buffer would be allocated.

To fix this, change __evict_old_buffers() so that it checks the
watermark.  __evict_old_buffers() is called every 30 seconds, so if the
user reduces "max_cache_size_bytes", dm-bufio will react to this change
within 30 seconds and decrease memory consumption.

Depends-on: 1b0fb5a5b2 ("dm bufio: avoid a possible ABBA deadlock")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm bufio: avoid a possible ABBA deadlock

commit 1b0fb5a5b2dc0dddcfa575060441a7176ba7ac37 upstream.

__get_memory_limit() tests if dm_bufio_cache_size changed and calls
__cache_size_refresh() if it did.  It takes dm_bufio_clients_lock while
it already holds the client lock.  However, lock ordering is violated
because in cleanup_old_buffers() dm_bufio_clients_lock is taken before
the client lock.

This results in a possible deadlock and lockdep engine warning.

Fix this deadlock by changing mutex_lock() to mutex_trylock().  If the
lock can't be taken, it will be re-checked next time when a new buffer
is allocated.

Also add "unlikely" to the if condition, so that the optimizer assumes
that the condition is false.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm raid: select the Kconfig option CONFIG_MD_RAID0

commit 7b81ef8b14f80033e4a4168d199a0f5fd79b9426 upstream.

Since the commit 0cf4503174c1 ("dm raid: add support for the MD RAID0
personality"), the dm-raid subsystem can activate a RAID-0 array.
Therefore, add MD_RAID0 to the dependencies of DM_RAID, so that MD_RAID0
will be selected when DM_RAID is selected.

Fixes: 0cf4503174c1 ("dm raid: add support for the MD RAID0 personality")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm btree: fix for dm_btree_find_lowest_key()

commit 7d1fedb6e96a960aa91e4ff70714c3fb09195a5a upstream.

dm_btree_find_lowest_key() is giving incorrect results.  find_key()
traverses the btree correctly for finding the highest key, but there is
an error in the way it traverses the btree for retrieving the lowest
key.  dm_btree_find_lowest_key() fetches the first key of the rightmost
block of the btree instead of fetching the first key from the leftmost
block.

Fix this by conditionally passing the correct parameter to value64()
based on the @find_highest flag.

Signed-off-by: Erez Zadok <ezk@fsl.cs.sunysb.edu>
Signed-off-by: Vinothkumar Raja <vinraja@cs.stonybrook.edu>
Signed-off-by: Nidhi Panpalia <npanpalia@cs.stonybrook.edu>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

infiniband: call ipv6 route lookup via the stub interface

commit eea40b8f624f25cbc02d55f2d93203f60cee9341 upstream.

The infiniband address handle can be triggered to resolve an ipv6
address in response to MAD packets, regardless of the ipv6
module being disabled via the kernel command line argument.

That will cause a call into the ipv6 routing code, which is not
initialized, and a conseguent oops.

This commit addresses the above issue replacing the direct lookup
call with an indirect one via the ipv6 stub, which is properly
initialized according to the ipv6 status (e.g. if ipv6 is
disabled, the routing lookup fails gracefully)

Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mlx5: Fix mlx5_ib_map_mr_sg mr length

commit 0a49f2c31c3efbeb0de3e4b5598764887f629be2 upstream.

In case we got an initial sg_offset, we need to
account for it in the mr length.

Fixes: ff2ba9936591 ("IB/core: Add passing an offset into the SG to ib_map_mr_sg")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Tested-by: Israel Rukshin <israelr@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: cs4271: configure reset GPIO as output

commit 49b2e27ab9f66b0a22c21980ad8118a4038324ae upstream.

During reset "refactoring" the output configuration was lost.
This commit repairs sound on EDB93XX boards.

Fixes: 9a397f4 ("ASoC: cs4271: add regulator consumer support")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tpm_crb: check for bad response size

commit 8569defde8057258835c51ce01a33de82e14b148 upstream.

Make sure size of response buffer is at least 6 bytes, or
we will underflow and pass large size_t to memcpy_fromio().
This was encountered while testing earlier version of
locality patchset.

Fixes: 30fc8d138e912 ("tpm: TPM 2.0 CRB Interface")
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tpm: add sleep only for retry in i2c_nuvoton_write_status()

commit 0afb7118ae021e80ecf70f5a3336e0935505518a upstream.

Currently, there is an unnecessary 1 msec delay added in
i2c_nuvoton_write_status() for the successful case. This
function is called multiple times during send() and recv(),
which implies adding multiple extra delays for every TPM
operation.

This patch calls usleep_range() only if retry is to be done.

Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tpm: msleep() delays - replace with usleep_range() in i2c nuvoton driver

commit a233a0289cf9a96ef9b42c730a7621ccbf9a6f98 upstream.

Commit 500462a9de65 "timers: Switch to a non-cascading wheel" replaced
the 'classic' timer wheel, which aimed for near 'exact' expiry of the
timers.  Their analysis was that the vast majority of timeout timers
are used as safeguards, not as real timers, and are cancelled or
rearmed before expiration.  The only exception noted to this were
networking timers with a small expiry time.

Not included in the analysis was the TPM polling timer, which resulted
in a longer normal delay and, every so often, a very long delay.  The
non-cascading wheel delay is based on CONFIG_HZ.  For a description of
the different rings and their delays, refer to the comments in
kernel/time/timer.c.

Below are the delays given for rings 0 - 2, which explains the longer
"normal" delays and the very, long delays as seen on systems with
CONFIG_HZ 250.

* HZ 1000 steps
 * Level Offset  Granularity            Range
 *  0      0         1 ms                0 ms - 63 ms
 *  1     64         8 ms               64 ms - 511 ms
 *  2    128        64 ms              512 ms - 4095 ms (512ms - ~4s)

* HZ  250
 * Level Offset  Granularity            Range
 *  0      0         4 ms                0 ms - 255 ms
 *  1     64        32 ms              256 ms - 2047 ms (256ms - ~2s)
 *  2    128       256 ms             2048 ms - 16383 ms (~2s - ~16s)

Below is a comparison of extending the TPM with 1000 measurements,
using msleep() vs. usleep_delay() when configured for 1000 hz vs. 250
hz, before and after commit 500462a9de65.

linux-4.7 | msleep() usleep_range()
1000 hz: 0m44.628s | 1m34.497s 29.243s
250 hz: 1m28.510s | 4m49.269s 32.386s

linux-4.7  | min-max (msleep)  min-max (usleep_range)
1000 hz: 0:017 - 2:760s | 0:015 - 3:967s    0:014 - 0:418s
250 hz: 0:028 - 1:954s | 0:040 - 4:096s    0:016 - 0:816s

This patch replaces the msleep() with usleep_range() calls in the
i2c nuvoton driver with a consistent max range value.

Signed-of-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tpm_tis_spi: Add small delay after last transfer

commit 5cc0101d1f88500f8901d01b035af743215d4c3a upstream.

Testing the implementation with a Raspberry Pi 2 showed that under some
circumstances its SPI master erroneously releases the CS line before the
transfer is complete, i.e. before the end of the last clock. In this case
the TPM ignores the transfer and misses for example the GO command. The
driver is unable to detect this communication problem and will wait for a
command response that is never going to arrive, timing out eventually.

As a workaround, the small delay ensures that the CS line is held long
enough, even with a faulty SPI master. Other SPI masters are not affected,
except for a negligible performance penalty.

Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tpm_tis_spi: Remove limitation of transfers to MAX_SPI_FRAMESIZE bytes

commit 591e48c26ced7c455751eef27fb5963e902c2137 upstream.

Limiting transfers to MAX_SPI_FRAMESIZE was not expected by the upper
layers, as tpm_tis has no such limitation. Add a loop to hide that
limitation.

v2: Moved scope of spi_message to the top as requested by Jarkko
Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tpm_tis_spi: Check correct byte for wait state indicator

commit e110cc69dc2ad679d6d478df636b99b14e6fbbc9 upstream.

Wait states are signaled in the last byte received from the TPM in
response to the header, not the first byte. Check rx_buf[3] instead of
rx_buf[0].

Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tpm_tis_spi: Abort transfer when too many wait states are signaled

commit 975094ddc369a32f27210248bdd9bbd153061b00 upstream.

Abort the transfer with ETIMEDOUT when the TPM signals more than
TPM_RETRY wait states. Continuing with the transfer in this state
will only lead to arbitrary failures in other parts of the code.

Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tpm_tis_spi: Use single function to transfer data

commit f848f2143ae42dc0918400039257a893835254d1 upstream.

The algorithm for sending data to the TPM is mostly identical to the
algorithm for receiving data from the TPM, so a single function is
sufficient to handle both cases.

This is a prequisite for all the other fixes, so we don't have to fix
everything twice (send/receive)

v2: u16 instead of u8 for the length.
Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fanotify: don't expose EOPENSTALE to userspace

commit 4ff33aafd32e084f5ee7faa54ba06e95f8b1b8af upstream.

When delivering an event to userspace for a file on an NFS share,
if the file is deleted on server side before user reads the event,
user will not get the event.

If the event queue contained several events, the stale event is
quietly dropped and read() returns to user with events read so far
in the buffer.

If the event queue contains a single stale event or if the stale
event is a permission event, read() returns to user with the kernel
internal error code 518 (EOPENSTALE), which is not a POSIX error code.

Check the internal return value -EOPENSTALE in fanotify_read(), just
the same as it is checked in path_openat() and drop the event in the
cases that it is not already dropped.

This is a reproducer from Marko Rauhamaa:

Just take the example program listed under "man fanotify" ("fantest")
and follow these steps:

    ==============================================================
    NFS Server    NFS Client(1)     NFS Client(2)
    ==============================================================
    # echo foo >/nfsshare/bar.txt
                  # cat /nfsshare/bar.txt
                  foo
                                    # ./fantest /nfsshare
                                    Press enter key to terminate.
                                    Listening for events.
    # rm -f /nfsshare/bar.txt
                  # cat /nfsshare/bar.txt
                                    read: Unknown error 518
                  cat: /nfsshare/bar.txt: Operation not permitted
    ==============================================================

where NFS Client (1) and (2) are two terminal sessions on a single NFS
Client machine.

Reported-by: Marko Rauhamaa <marko.rauhamaa@f-secure.com>
Tested-by: Marko Rauhamaa <marko.rauhamaa@f-secure.com>
Cc: <linux-api@vger.kernel.org>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: tegra: paz00: Mark panel regulator as enabled on boot

commit 0c18927f51f4d390abdcf385bff5f995407ee732 upstream.

Current U-Boot enables the display already. Marking the regulator as
enabled on boot fixes sporadic panel initialization failures.

Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Tested-by: Misha Komarovskiy <zombah@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda: Fix cpu lockup when stopping the cmd dmas

commit 960013762df0a214b57f2fce655422fb52bdfd2c upstream.

Using jiffies in hdac_wait_for_cmd_dmas() to determine when to time out
when interrupts are off (snd_hdac_bus_stop_cmd_io()/spin_lock_irq())
causes hard lockup so unlock while waiting using jiffies.

---<-snip->---
<0>[ 1211.603046] NMI watchdog: Watchdog detected hard LOCKUP on cpu 3
<4>[ 1211.603047] Modules linked in: snd_hda_intel i915 vgem
<4>[ 1211.603053] irq event stamp: 13366
<4>[ 1211.603053] hardirqs last  enabled at (13365):
...
<4>[ 1211.603059] Call Trace:
<4>[ 1211.603059]  ? delay_tsc+0x3d/0xc0
<4>[ 1211.603059]  __delay+0xa/0x10
<4>[ 1211.603060]  __const_udelay+0x31/0x40
<4>[ 1211.603060]  snd_hdac_bus_stop_cmd_io+0x96/0xe0 [snd_hda_core]
<4>[ 1211.603060]  ? azx_dev_disconnect+0x20/0x20 [snd_hda_intel]
<4>[ 1211.603061]  snd_hdac_bus_stop_chip+0xb1/0x100 [snd_hda_core]
<4>[ 1211.603061]  azx_stop_chip+0x9/0x10 [snd_hda_codec]
<4>[ 1211.603061]  azx_suspend+0x72/0x220 [snd_hda_intel]
<4>[ 1211.603061]  pci_pm_suspend+0x71/0x140
<4>[ 1211.603062]  dpm_run_callback+0x6f/0x330
<4>[ 1211.603062]  ? pci_pm_freeze+0xe0/0xe0
<4>[ 1211.603062]  __device_suspend+0xf9/0x370
<4>[ 1211.603062]  ? dpm_watchdog_set+0x60/0x60
<4>[ 1211.603063]  async_suspend+0x1a/0x90
<4>[ 1211.603063]  async_run_entry_fn+0x34/0x160
<4>[ 1211.603063]  process_one_work+0x1f4/0x6d0
<4>[ 1211.603063]  ? process_one_work+0x16e/0x6d0
<4>[ 1211.603064]  worker_thread+0x49/0x4a0
<4>[ 1211.603064]  kthread+0x107/0x140
<4>[ 1211.603064]  ? process_one_work+0x6d0/0x6d0
<4>[ 1211.603065]  ? kthread_create_on_node+0x40/0x40
<4>[ 1211.603065]  ret_from_fork+0x2e/0x40

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100419
Fixes: 38b19ed7f81ec ("ALSA: hda: fix to wait for RIRB & CORB DMA to set")
Reported-by: Marta Lofstedt <marta.lofstedt@intel.com>
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tpm_tis_core: Choose appropriate timeout for reading burstcount

commit 302a6ad7fc77146191126a1f3e2c5d724fd72416 upstream.

TIS v1.3 for TPM 1.2 and PTP for TPM 2.0 disagree about which timeout
value applies to reading a valid burstcount. It is TIMEOUT_D according to
TIS, but TIMEOUT_A according to PTP, so choose the appropriate value
depending on whether we deal with a TPM 1.2 or a TPM 2.0.

This is important since according to the PTP TIMEOUT_D is much smaller
than TIMEOUT_A. So the previous implementation could run into timeouts
with a TPM 2.0, even though the TPM was behaving perfectly fine.

During tpm2_probe TIMEOUT_D will be used even with a TPM 2.0, because
TPM_CHIP_FLAG_TPM2 is not yet set. This is fine, since the timeout values
will only be changed afterwards by tpm_get_timeouts. Until then
TIS_TIMEOUT_D_MAX applies, which is large enough.

Fixes: aec04cbdf723 ("tpm: TPM 2.0 FIFO Interface")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: core: replace %p with %pK

commit 2f964780c03b73de269b08d12aff96a9618d13f3 upstream.

Format specifier %p can leak kernel addresses while not valuing the
kptr_restrict system settings. When kptr_restrict is set to (1), kernel
pointers printed using the %pK format specifier will be replaced with
Zeros. Debugging Note : &pK prints only Zeros as address. If you need
actual address information, write 0 to kptr_restrict.

echo 0 > /proc/sys/kernel/kptr_restrict

[Found by poking around in a random vendor kernel tree, it would be nice
if someone would actually send these types of patches upstream - gkh]

Signed-off-by: Vamsi Krishna Samavedam <vskrishn@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

char: lp: fix possible integer overflow in lp_setup()

commit 3e21f4af170bebf47c187c1ff8bf155583c9f3b1 upstream.

The lp_setup() code doesn't apply any bounds checking when passing
"lp=none", and only in this case, resulting in an overflow of the
parport_nr[] array. All versions in Git history are affected.

Reported-By: Roee Hay <roee.hay@hcl.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

watchdog: pcwd_usb: fix NULL-deref at probe

commit 46c319b848268dab3f0e7c4a5b6e9146d3bca8a4 upstream.

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: ene_usb6250: fix DMA to the stack

commit 628c2893d44876ddd11602400c70606ade62e129 upstream.

The ene_usb6250 sub-driver in usb-storage does USB I/O to buffers on
the stack, which doesn't work with vmapped stacks.  This patch fixes
the problem by allocating a separate 512-byte buffer at probe time and
using it for all of the offending I/O operations.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: misc: legousbtower: Fix memory leak

commit 0bd193d62b4270a2a7a09da43ad1034c7ca5b3d3 upstream.

get_version_reply is not freed if function returns with success.

Fixes: 942a48730faf ("usb: misc: legousbtower: Fix buffers on stack")
Reported-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: misc: legousbtower: Fix buffers on stack

commit 942a48730faf149ccbf3e12ac718aee120bb3529 upstream.

Allocate buffers on HEAP instead of STACK for local structures
that are to be received using usb_control_msg().

Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Tested-by: Alfredo Rafael Vicente Boix <alviboi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.9.29

pstore: Shut down worker when unregistering

commit 6330d5534786d5315d56d558aa6d20740f97d80a upstream.

When built as a module and running with update_ms >= 0, pstore will Oops
during module unload since the work timer is still running. This makes sure
the worker is stopped before unloading.

Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pstore: Fix flags to enable dumps on powerpc

commit 041939c1ec54208b42f5cd819209173d52a29d34 upstream.

After commit c950fd6f201a kernel registers pstore write based on flag set.
Pstore write for powerpc is broken as flags(PSTORE_FLAGS_DMESG) is not set for
powerpc architecture. On panic, kernel doesn't write message to
/fs/pstore/dmesg*(Entry doesn't gets created at all).

This patch enables pstore write for powerpc architecture by setting
PSTORE_FLAGS_DMESG flag.

Fixes: c950fd6f201a ("pstore: Split pstore fragile flags")
Signed-off-by: Ankit Kumar <ankit@linux.vnet.ibm.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

libnvdimm, pfn: fix 'npfns' vs section alignment

commit d5483feda85a8f39ee2e940e279547c686aac30c upstream.

Fix failures to create namespaces due to the vmem_altmap not advertising
enough free space to store the memmap.

 WARNING: CPU: 15 PID: 8022 at arch/x86/mm/init_64.c:656 arch_add_memory+0xde/0xf0
 [..]
 Call Trace:
  dump_stack+0x63/0x83
  __warn+0xcb/0xf0
  warn_slowpath_null+0x1d/0x20
  arch_add_memory+0xde/0xf0
  devm_memremap_pages+0x244/0x440
  pmem_attach_disk+0x37e/0x490 [nd_pmem]
  nd_pmem_probe+0x7e/0xa0 [nd_pmem]
  nvdimm_bus_probe+0x71/0x120 [libnvdimm]
  driver_probe_device+0x2bb/0x460
  bind_store+0x114/0x160
  drv_attr_store+0x25/0x30

In commit 658922e57b84 "libnvdimm, pfn: fix memmap reservation sizing"
we arranged for the capacity to be allocated, but failed to also update
the 'npfns' parameter. This leads to cases where there is enough
capacity reserved to hold all the allocated sections, but
vmemmap_populate_hugepages() still encounters -ENOMEM from
altmap_alloc_block_buf().

This fix is a stop-gap until we can teach the core memory hotplug
implementation to permit sub-section hotplug.

Fixes: 658922e57b84 ("libnvdimm, pfn: fix memmap reservation sizing")
Reported-by: Anisha Allada <anisha.allada@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

libnvdimm, pmem: fix a NULL pointer BUG in nd_pmem_notify

commit b2518c78ce76896f0f8f7940bf02104b227e1709 upstream.

The following BUG was observed when nd_pmem_notify() was called
for a BTT device.  The use of a pmem_device pointer is not valid
with BTT.

 BUG: unable to handle kernel NULL pointer dereference at 0000000000000030
 IP: nd_pmem_notify+0x30/0xf0 [nd_pmem]
 Call Trace:
  nd_device_notify+0x40/0x50
  child_notify+0x10/0x20
  device_for_each_child+0x50/0x90
  nd_region_notify+0x20/0x30
  nd_device_notify+0x40/0x50
  nvdimm_region_notify+0x27/0x30
  acpi_nfit_scrub+0x341/0x590 [nfit]
  process_one_work+0x197/0x450
  worker_thread+0x4e/0x4a0
  kthread+0x109/0x140

Fix nd_pmem_notify() by setting nd_region and badblocks pointers
properly for BTT.

Cc: Vishal Verma <vishal.l.verma@intel.com>
Fixes: 719994660c24 ("libnvdimm: async notification support")
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

libnvdimm, region: fix flush hint detection crash

commit bc042fdfbb92b5b13421316b4548e2d6e98eed37 upstream.

In the case where a dimm does not have any associated flush hints the
ndrd->flush_wpq array may be uninitialized leading to crashes with the
following signature:

 BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
 IP: region_visible+0x10f/0x160 [libnvdimm]

 Call Trace:
  internal_create_group+0xbe/0x2f0
  sysfs_create_groups+0x40/0x80
  device_add+0x2d8/0x650
  nd_async_device_register+0x12/0x40 [libnvdimm]
  async_run_entry_fn+0x39/0x170
  process_one_work+0x212/0x6c0
  ? process_one_work+0x197/0x6c0
  worker_thread+0x4e/0x4a0
  kthread+0x10c/0x140
  ? process_one_work+0x6c0/0x6c0
  ? kthread_create_on_node+0x60/0x60
  ret_from_fork+0x31/0x40

Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Fixes: f284a4f23752 ("libnvdimm: introduce nvdimm_flush() and nvdimm_has_flush()")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipmi: Fix kernel panic at ipmi_ssif_thread()

commit 6de65fcfdb51835789b245203d1bfc8d14cb1e06 upstream.

msg_written_handler() may set ssif_info->multi_data to NULL
when using ipmitool to write fru.

Before setting ssif_info->multi_data to NULL, add new local
pointer "data_to_send" and store correct i2c data pointer to
it to fix NULL pointer kernel panic and incorrect ssif_info->multi_pos.

Signed-off-by: Joeseph Chang <joechang@codeaurora.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: hci_intel: add missing tty-device sanity check

commit dcb9cfaa5ea9aa0ec08aeb92582ccfe3e4c719a9 upstream.

Make sure to check the tty-device pointer before looking up the sibling
platform device to avoid dereferencing a NULL-pointer when the tty is
one end of a Unix98 pty.

Fixes: 74cdad37cd24 ("Bluetooth: hci_intel: Add runtime PM support")
Fixes: 1ab1f239bf17 ("Bluetooth: hci_intel: Add support for platform driver")
Cc: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: hci_bcm: add missing tty-device sanity check

commit 95065a61e9bf25fb85295127fba893200c2bbbd8 upstream.

Make sure to check the tty-device pointer before looking up the sibling
platform device to avoid dereferencing a NULL-pointer when the tty is
one end of a Unix98 pty.

Fixes: 0395ffc1ee05 ("Bluetooth: hci_bcm: Add PM for BCM devices")
Cc: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: Fix user channel for 32bit userspace on 64bit kernel

commit ab89f0bdd63a3721f7cd3f064f39fc4ac7ca14d4 upstream.

Running 32bit userspace on 64bit kernel results in MSG_CMSG_COMPAT being
defined as 0x80000000. This results in sendmsg failure if used from 32bit
userspace running on 64bit kernel. Fix this by accounting for MSG_CMSG_COMPAT
in flags check in hci_sock_sendmsg.

Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marko Kiiskila <marko@runtime.io>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: pty: Fix ldisc flush after userspace become aware of the data already

commit 77dae6134440420bac334581a3ccee94cee1c054 upstream.

While using emacs, cat or others' commands in konsole with recent
kernels, I have met many times that CTRL-C freeze konsole. After
konsole freeze I can't type anything, then I have to open a new one,
it is very annoying.

See bug report:
https://bugs.kde.org/show_bug.cgi?id=175283

The platform in that bug report is Solaris, but now the pty in linux
has the same problem or the same behavior as Solaris :)

It has high possibility to trigger the problem follow steps below:
Note: In my test, BigFile is a text file whose size is bigger than 1G
1:open konsole
1:cat BigFile
2:CTRL-C

After some digging, I find out the reason is that commit 1d1d14da12e7
("pty: Fix buffer flush deadlock") changes the behavior of pty_flush_buffer.

Thread A                                 Thread B
--------                                 --------
1:n_tty_poll return POLLIN
                                         2:CTRL-C trigger pty_flush_buffer
                                             tty_buffer_flush
                                               n_tty_flush_buffer
3:attempt to check count of chars:
  ioctl(fd, TIOCINQ, &available)
  available is equal to 0

4:read(fd, buffer, avaiable)
  return 0

5:konsole close fd

Yes, I know we could use the same patch included in the BUG report as
a workaround for linux platform too. But I think the data in ldisc is
belong to application of another side, we shouldn't clear it when we
want to flush write buffer of this side in pty_flush_buffer. So I think
it is better to disable ldisc flush in pty_flush_buffer, because its new
hehavior bring no benefit except that it mess up the behavior between
POLLIN, and TIOCINQ or FIONREAD.

Also I find no flush_buffer function in others' tty driver has the
same behavior as current pty_flush_buffer.

Fixes: 1d1d14da12e7 ("pty: Fix buffer flush deadlock")
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: omap: suspend device on probe errors

commit 77e6fe7fd2b7cba0bf2f2dc8cde51d7b9a35bf74 upstream.

Make sure to actually suspend the device before returning after a failed
(or deferred) probe.

Note that autosuspend must be disabled before runtime pm is disabled in
order to balance the usage count due to a negative autosuspend delay as
well as to make the final put suspend the device synchronously.

Fixes: 388bc2622680 ("omap-serial: Fix the error handling in the omap_serial probe")
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: omap: fix runtime-pm handling on unbind

commit 099bd73dc17ed77aa8c98323e043613b6e8f54fc upstream.

An unbalanced and misplaced synchronous put was used to suspend the
device on driver unbind, something which with a likewise misplaced
pm_runtime_disable leads to external aborts when an open port is being
removed.

Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa024010
...
[<c046e760>] (serial_omap_set_mctrl) from [<c046a064>] (uart_update_mctrl+0x50/0x60)
[<c046a064>] (uart_update_mctrl) from [<c046a400>] (uart_shutdown+0xbc/0x138)
[<c046a400>] (uart_shutdown) from [<c046bd2c>] (uart_hangup+0x94/0x190)
[<c046bd2c>] (uart_hangup) from [<c045b760>] (__tty_hangup+0x404/0x41c)
[<c045b760>] (__tty_hangup) from [<c045b794>] (tty_vhangup+0x1c/0x20)
[<c045b794>] (tty_vhangup) from [<c046ccc8>] (uart_remove_one_port+0xec/0x260)
[<c046ccc8>] (uart_remove_one_port) from [<c046ef4c>] (serial_omap_remove+0x40/0x60)
[<c046ef4c>] (serial_omap_remove) from [<c04845e8>] (platform_drv_remove+0x34/0x4c)

Fix this up by resuming the device before deregistering the port and by
suspending and disabling runtime pm only after the port has been
removed.

Also make sure to disable autosuspend before disabling runtime pm so
that the usage count is balanced and device actually suspended before
returning.

Note that due to a negative autosuspend delay being set in probe, the
unbalanced put would actually suspend the device on first driver unbind,
while rebinding and again unbinding would result in a negative
power.usage_count.

Fixes: 7e9c8e7dbf3b ("serial: omap: make sure to suspend device before remove")
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: samsung: Use right device for DMA-mapping calls

commit 768d64f491a530062ddad50e016fb27125f8bd7c upstream.

Driver should provide its own struct device for all DMA-mapping calls instead
of extracting device pointer from DMA engine channel. Although this is harmless
from the driver operation perspective on ARM architecture, it is always good
to use the DMA mapping API in a proper way. This patch fixes following DMA API
debug warning:

WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:1241 check_sync+0x520/0x9f4
samsung-uart 12c20000.serial: DMA-API: device driver tries to sync DMA memory it has not allocated [device address=0x000000006df0f580] [size=64 bytes]
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.11.0-rc1-00137-g07ca963 #51
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c011aaa4>] (unwind_backtrace) from [<c01127c0>] (show_stack+0x20/0x24)
[<c01127c0>] (show_stack) from [<c06ba5d8>] (dump_stack+0x84/0xa0)
[<c06ba5d8>] (dump_stack) from [<c0139528>] (__warn+0x14c/0x180)
[<c0139528>] (__warn) from [<c01395a4>] (warn_slowpath_fmt+0x48/0x50)
[<c01395a4>] (warn_slowpath_fmt) from [<c0729058>] (check_sync+0x520/0x9f4)
[<c0729058>] (check_sync) from [<c072967c>] (debug_dma_sync_single_for_device+0x88/0xc8)
[<c072967c>] (debug_dma_sync_single_for_device) from [<c0803c10>] (s3c24xx_serial_start_tx_dma+0x100/0x2f8)
[<c0803c10>] (s3c24xx_serial_start_tx_dma) from [<c0804338>] (s3c24xx_serial_tx_chars+0x198/0x33c)

Reported-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Fixes: 62c37eedb74c8 ("serial: samsung: add dma reqest/release functions")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fscrypt: fix context consistency check when key(s) unavailable

commit 272f98f6846277378e1758a49a49d7bf39343c02 upstream.

To mitigate some types of offline attacks, filesystem encryption is
designed to enforce that all files in an encrypted directory tree use
the same encryption policy (i.e. the same encryption context excluding
the nonce).  However, the fscrypt_has_permitted_context() function which
enforces this relies on comparing struct fscrypt_info's, which are only
available when we have the encryption keys.  This can cause two
incorrect behaviors:

1. If we have the parent directory's key but not the child's key, or
   vice versa, then fscrypt_has_permitted_context() returned false,
   causing applications to see EPERM or ENOKEY.  This is incorrect if
   the encryption contexts are in fact consistent.  Although we'd
   normally have either both keys or neither key in that case since the
   master_key_descriptors would be the same, this is not guaranteed
   because keys can be added or removed from keyrings at any time.

2. If we have neither the parent's key nor the child's key, then
   fscrypt_has_permitted_context() returned true, causing applications
   to see no error (or else an error for some other reason).  This is
   incorrect if the encryption contexts are in fact inconsistent, since
   in that case we should deny access.

To fix this, retrieve and compare the fscrypt_contexts if we are unable
to set up both fscrypt_infos.

While this slightly hurts performance when accessing an encrypted
directory tree without the key, this isn't a case we really need to be
optimizing for; access *with* the key is much more important.
Furthermore, the performance hit is barely noticeable given that we are
already retrieving the fscrypt_context and doing two keyring searches in
fscrypt_get_encryption_info().  If we ever actually wanted to optimize
this case we might start by caching the fscrypt_contexts.

Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

device-dax: fix cdev leak

commit ed01e50acdd3e4a640cf9ebd28a7e810c3ceca97 upstream.

If device_add() fails, cleanup the cdev. Otherwise, we leak a kobj_map()
with a stale device number.

As Jason points out, there is a small possibility that userspace has
opened and mapped the device in the time between cdev_add() and the
device_add() failure. We need a new kill_dax_dev() helper to invalidate
any established mappings.

Fixes: ba09c01d2fa8 ("dax: convert to the cdev api")
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

padata: free correct variable

commit 07a77929ba672d93642a56dc2255dd21e6e2290b upstream.

The author meant to free the variable that was just allocated, instead
of the one that failed to be allocated, but made a simple typo. This
patch rectifies that.

Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

CIFS: add misssing SFM mapping for doublequote

commit 85435d7a15294f9f7ef23469e6aaf7c5dfcc54f0 upstream.

SFM is mapping doublequote to 0xF020

Without this patch creating files with doublequote fails to Windows/Mac

Signed-off-by: Bjoern Jacke <bjacke@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: fix CIFS_IOC_GET_MNT_INFO oops

commit d8a6e505d6bba2250852fbc1c1c86fe68aaf9af3 upstream.

An open directory may have a NULL private_data pointer prior to readdir.

Fixes: 0de1f4c6f6c0 ("Add way to query server fs info for smb3")
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

CIFS: fix oplock break deadlocks

commit 3998e6b87d4258a70df358296d6f1c7234012bfe upstream.

When the final cifsFileInfo_put() is called from cifsiod and an oplock
break work is queued, lockdep complains loudly:

 =============================================
 [ INFO: possible recursive locking detected ]
 4.11.0+ #21 Not tainted
 ---------------------------------------------
 kworker/0:2/78 is trying to acquire lock:
  ("cifsiod"){++++.+}, at: flush_work+0x215/0x350

 but task is already holding lock:
  ("cifsiod"){++++.+}, at: process_one_work+0x255/0x8e0

 other info that might help us debug this:
  Possible unsafe locking scenario:

        CPU0
        ----
   lock("cifsiod");
   lock("cifsiod");

  *** DEADLOCK ***

  May be due to missing lock nesting notation

 2 locks held by kworker/0:2/78:
  #0:  ("cifsiod"){++++.+}, at: process_one_work+0x255/0x8e0
  #1:  ((&wdata->work)){+.+...}, at: process_one_work+0x255/0x8e0

 stack backtrace:
 CPU: 0 PID: 78 Comm: kworker/0:2 Not tainted 4.11.0+ #21
 Workqueue: cifsiod cifs_writev_complete
 Call Trace:
  dump_stack+0x85/0xc2
  __lock_acquire+0x17dd/0x2260
  ? match_held_lock+0x20/0x2b0
  ? trace_hardirqs_off_caller+0x86/0x130
  ? mark_lock+0xa6/0x920
  lock_acquire+0xcc/0x260
  ? lock_acquire+0xcc/0x260
  ? flush_work+0x215/0x350
  flush_work+0x236/0x350
  ? flush_work+0x215/0x350
  ? destroy_worker+0x170/0x170
  __cancel_work_timer+0x17d/0x210
  ? ___preempt_schedule+0x16/0x18
  cancel_work_sync+0x10/0x20
  cifsFileInfo_put+0x338/0x7f0
  cifs_writedata_release+0x2a/0x40
  ? cifs_writedata_release+0x2a/0x40
  cifs_writev_complete+0x29d/0x850
  ? preempt_count_sub+0x18/0xd0
  process_one_work+0x304/0x8e0
  worker_thread+0x9b/0x6a0
  kthread+0x1b2/0x200
  ? process_one_work+0x8e0/0x8e0
  ? kthread_create_on_node+0x40/0x40
  ret_from_fork+0x31/0x40

This is a real warning.  Since the oplock is queued on the same
workqueue this can deadlock if there is only one worker thread active
for the workqueue (which will be the case during memory pressure when
the rescuer thread is handling it).

Furthermore, there is at least one other kind of hang possible due to
the oplock break handling if there is only worker.  (This can be
reproduced without introducing memory pressure by having passing 1 for
the max_active parameter of cifsiod.) cifs_oplock_break() can wait
indefintely in the filemap_fdatawait() while the cifs_writev_complete()
work is blocked:

 sysrq: SysRq : Show Blocked State
   task                        PC stack   pid father
 kworker/0:1     D    0    16      2 0x00000000
 Workqueue: cifsiod cifs_oplock_break
 Call Trace:
  __schedule+0x562/0xf40
  ? mark_held_locks+0x4a/0xb0
  schedule+0x57/0xe0
  io_schedule+0x21/0x50
  wait_on_page_bit+0x143/0x190
  ? add_to_page_cache_lru+0x150/0x150
  __filemap_fdatawait_range+0x134/0x190
  ? do_writepages+0x51/0x70
  filemap_fdatawait_range+0x14/0x30
  filemap_fdatawait+0x3b/0x40
  cifs_oplock_break+0x651/0x710
  ? preempt_count_sub+0x18/0xd0
  process_one_work+0x304/0x8e0
  worker_thread+0x9b/0x6a0
  kthread+0x1b2/0x200
  ? process_one_work+0x8e0/0x8e0
  ? kthread_create_on_node+0x40/0x40
  ret_from_fork+0x31/0x40
 dd              D    0   683    171 0x00000000
 Call Trace:
  __schedule+0x562/0xf40
  ? mark_held_locks+0x29/0xb0
  schedule+0x57/0xe0
  io_schedule+0x21/0x50
  wait_on_page_bit+0x143/0x190
  ? add_to_page_cache_lru+0x150/0x150
  __filemap_fdatawait_range+0x134/0x190
  ? do_writepages+0x51/0x70
  filemap_fdatawait_range+0x14/0x30
  filemap_fdatawait+0x3b/0x40
  filemap_write_and_wait+0x4e/0x70
  cifs_flush+0x6a/0xb0
  filp_close+0x52/0xa0
  __close_fd+0xdc/0x150
  SyS_close+0x33/0x60
  entry_SYSCALL_64_fastpath+0x1f/0xbe

 Showing all locks held in the system:
 2 locks held by kworker/0:1/16:
  #0:  ("cifsiod"){.+.+.+}, at: process_one_work+0x255/0x8e0
  #1:  ((&cfile->oplock_break)){+.+.+.}, at: process_one_work+0x255/0x8e0

 Showing busy workqueues and worker pools:
 workqueue cifsiod: flags=0xc
   pwq 0: cpus=0 node=0 flags=0x0 nice=0 active=1/1
     in-flight: 16:cifs_oplock_break
     delayed: cifs_writev_complete, cifs_echo_request
 pool 0: cpus=0 node=0 flags=0x0 nice=0 hung=0s workers=3 idle: 750 3

Fix these problems by creating a a new workqueue (with a rescuer) for
the oplock break work.

Signed-off-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: fix CIFS_ENUMERATE_SNAPSHOTS oops

commit 6026685de33b0db5b2b6b0e9b41b3a1a3261033c upstream.

As with 618763958b22, an open directory may have a NULL private_data
pointer prior to readdir. CIFS_ENUMERATE_SNAPSHOTS must check for this
before dereference.

Fixes: 834170c85978 ("Enable previous version support")
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: fix leak in FSCTL_ENUM_SNAPS response handling

commit 0e5c795592930d51fd30d53a2e7b73cba022a29b upstream.

The server may respond with success, and an output buffer less than
sizeof(struct smb_snapshot_array) in length. Do not leak the output
buffer in this case.

Fixes: 834170c85978 ("Enable previous version support")
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

CIFS: fix mapping of SFM_SPACE and SFM_PERIOD

commit b704e70b7cf48f9b67c07d585168e102dfa30bb4 upstream.

- trailing space maps to 0xF028
- trailing period maps to 0xF029

This fix corrects the mapping of file names which have a trailing character
that would otherwise be illegal (period or space) but is allowed by POSIX.

Signed-off-by: Bjoern Jacke <bjacke@samba.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SMB3: Work around mount failure when using SMB3 dialect to Macs

commit 7db0a6efdc3e990cdfd4b24820d010e9eb7890ad upstream.

Macs send the maximum buffer size in response on ioctl to validate
negotiate security information, which causes us to fail the mount
as the response buffer is larger than the expected response.

Changed ioctl response processing to allow for padding of validate
negotiate ioctl response and limit the maximum response size to
maximum buffer size.

Signed-off-by: Steve French <steve.french@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Set unicode flag on cifs echo request to avoid Mac error

commit 26c9cb668c7fbf9830516b75d8bee70b699ed449 upstream.

Mac requires the unicode flag to be set for cifs, even for the smb
echo request (which doesn't have strings).

Without this Mac rejects the periodic echo requests (when mounting
with cifs) that we use to check if server is down

Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix match_prepath()

commit cd8c42968ee651b69e00f8661caff32b0086e82d upstream.

Incorrect return value for shares not using the prefix path means that
we will never match superblocks for these shares.

Fixes: commit c1d8b24d1819 ("Compare prepaths when comparing superblocks")
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm: prevent potential recursive reclaim due to clearing PF_MEMALLOC

commit 62be1511b1db8066220b18b7d4da2e6b9fdc69fb upstream.

Patch series "more robust PF_MEMALLOC handling"

This series aims to unify the setting and clearing of PF_MEMALLOC, which
prevents recursive reclaim.  There are some places that clear the flag
unconditionally from current->flags, which may result in clearing a
pre-existing flag.  This already resulted in a bug report that Patch 1
fixes (without the new helpers, to make backporting easier).  Patch 2
introduces the new helpers, modelled after existing memalloc_noio_* and
memalloc_nofs_* helpers, and converts mm core to use them.  Patches 3
and 4 convert non-mm code.

This patch (of 4):

__alloc_pages_direct_compact() sets PF_MEMALLOC to prevent deadlock
during page migration by lock_page() (see the comment in
__unmap_and_move()).  Then it unconditionally clears the flag, which can
clear a pre-existing PF_MEMALLOC flag and result in recursive reclaim.
This was not a problem until commit a8161d1ed609 ("mm, page_alloc:
restructure direct compaction handling in slowpath"), because direct
compation was called only after direct reclaim, which was skipped when
PF_MEMALLOC flag was set.

Even now it's only a theoretical issue, as the new callsite of
__alloc_pages_direct_compact() is reached only for costly orders and
when gfp_pfmemalloc_allowed() is true, which means either
__GFP_NOMEMALLOC is in gfp_flags or in_interrupt() is true.  There is no
such known context, but let's play it safe and make
__alloc_pages_direct_compact() robust for cases where PF_MEMALLOC is
already set.

Fixes: a8161d1ed609 ("mm, page_alloc: restructure direct compaction handling in slowpath")
Link: http://lkml.kernel.org/r/20170405074700.29871-2-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Chris Leech <cleech@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fs/block_dev: always invalidate cleancache in invalidate_bdev()

commit a5f6a6a9c72eac38a7fadd1a038532bc8516337c upstream.

invalidate_bdev() calls cleancache_invalidate_inode() iff ->nrpages != 0
which doen't make any sense.

Make sure that invalidate_bdev() always calls cleancache_invalidate_inode()
regardless of mapping->nrpages value.

Fixes: c515e1fd361c ("mm/fs: add hooks to support cleancache")
Link: http://lkml.kernel.org/r/20170424164135.22350-3-aryabinin@virtuozzo.com
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Alexey Kuznetsov <kuznet@virtuozzo.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Nikolay Borisov <n.borisov.lkml@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ceph: fix memory leak in __ceph_setxattr()

commit eeca958dce0a9231d1969f86196653eb50fcc9b3 upstream.

The ceph_inode_xattr needs to be released when removing an xattr.  Easily
reproducible running the 'generic/020' test from xfstests or simply by
doing:

  attr -s attr0 -V 0 /mnt/test && attr -r attr0 /mnt/test

While there, also fix the error path.

Here's the kmemleak splat:

unreferenced object 0xffff88001f86fbc0 (size 64):
  comm "attr", pid 244, jiffies 4294904246 (age 98.464s)
  hex dump (first 32 bytes):
    40 fa 86 1f 00 88 ff ff 80 32 38 1f 00 88 ff ff  @........28.....
    00 01 00 00 00 00 ad de 00 02 00 00 00 00 ad de  ................
  backtrace:
    [<ffffffff81560199>] kmemleak_alloc+0x49/0xa0
    [<ffffffff810f3e5b>] kmem_cache_alloc+0x9b/0xf0
    [<ffffffff812b157e>] __ceph_setxattr+0x17e/0x820
    [<ffffffff812b1c57>] ceph_set_xattr_handler+0x37/0x40
    [<ffffffff8111fb4b>] __vfs_removexattr+0x4b/0x60
    [<ffffffff8111fd37>] vfs_removexattr+0x77/0xd0
    [<ffffffff8111fdd1>] removexattr+0x41/0x60
    [<ffffffff8111fe65>] path_removexattr+0x75/0xa0
    [<ffffffff81120aeb>] SyS_lremovexattr+0xb/0x10
    [<ffffffff81564b20>] entry_SYSCALL_64_fastpath+0x13/0x94
    [<ffffffffffffffff>] 0xffffffffffffffff

Signed-off-by: Luis Henriques <lhenriques@suse.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fs/xattr.c: zero out memory copied to userspace in getxattr

commit 81be3dee96346fbe08c31be5ef74f03f6b63cf68 upstream.

getxattr uses vmalloc to allocate memory if kzalloc fails.  This is
filled by vfs_getxattr and then copied to the userspace.  vmalloc,
however, doesn't zero out the memory so if the specific implementation
of the xattr handler is sloppy we can theoretically expose a kernel
memory.  There is no real sign this is really the case but let's make
sure this will not happen and use vzalloc instead.

Fixes: 779302e67835 ("fs/xattr.c:getxattr(): improve handling of allocation failures")
Link: http://lkml.kernel.org/r/20170306103327.2766-1-mhocko@kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

orangefs: do not check possibly stale size on truncate

commit 53950ef541675df48c219a8d665111a0e68dfc2f upstream.

Let the server figure this out because our size might be out of date or
not present.

The bug was that

xfs_io -f -t -c "pread -v 0 100" /mnt/foo
echo "Test" > /mnt/foo
xfs_io -f -t -c "pread -v 0 100" /mnt/foo

fails because the second truncate did not happen if nothing had
requested the size after the write in echo.  Thus i_size was zero (not
present) and the orangefs_setattr though i_size was zero and there was
nothing to do.

Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

orangefs: do not set getattr_time on orangefs_lookup

commit 17930b252cd6f31163c259eaa99dd8aa630fb9ba upstream.

Since orangefs_lookup calls orangefs_iget which calls
orangefs_inode_getattr, getattr_time will get set.

Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

orangefs: clean up oversize xattr validation

commit e675c5ec51fe2554719a7b6bcdbef0a770f2c19b upstream.

Also don't check flags as this has been validated by the VFS already.

Fix an off-by-one error in the max size checking.

Stop logging just because userspace wants to write attributes which do
not fit.

This and the previous commit fix xfstests generic/020.

Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

orangefs: fix bounds check for listxattr

commit a956af337b9ff25822d9ce1a59c6ed0c09fc14b9 upstream.

Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: evict inline data when writing to memory map

commit 7b4cc9787fe35b3ee2dfb1c35e22eafc32e00c33 upstream.

Currently the case of writing via mmap to a file with inline data is not
handled.  This is maybe a rare case since it requires a writable memory
map of a very small file, but it is trivial to trigger with on
inline_data filesystem, and it causes the
'BUG_ON(ext4_test_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA));' in
ext4_writepages() to be hit:

    mkfs.ext4 -O inline_data /dev/vdb
    mount /dev/vdb /mnt
    xfs_io -f /mnt/file \
-c 'pwrite 0 1' \
-c 'mmap -w 0 1m' \
-c 'mwrite 0 1' \
-c 'fsync'

kernel BUG at fs/ext4/inode.c:2723!
invalid opcode: 0000 [#1] SMP
CPU: 1 PID: 2532 Comm: xfs_io Not tainted 4.11.0-rc1-xfstests-00301-g071d9acf3d1f #633
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-20170228_101828-anatol 04/01/2014
task: ffff88003d3a8040 task.stack: ffffc90000300000
RIP: 0010:ext4_writepages+0xc89/0xf8a
RSP: 0018:ffffc90000303ca0 EFLAGS: 00010283
RAX: 0000028410000000 RBX: ffff8800383fa3b0 RCX: ffffffff812afcdc
RDX: 00000a9d00000246 RSI: ffffffff81e660e0 RDI: 0000000000000246
RBP: ffffc90000303dc0 R08: 0000000000000002 R09: 869618e8f99b4fa5
R10: 00000000852287a2 R11: 00000000a03b49f4 R12: ffff88003808e698
R13: 0000000000000000 R14: 7fffffffffffffff R15: 7fffffffffffffff
FS:  00007fd3e53094c0(0000) GS:ffff88003e400000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fd3e4c51000 CR3: 000000003d554000 CR4: 00000000003406e0
Call Trace:
 ? _raw_spin_unlock+0x27/0x2a
 ? kvm_clock_read+0x1e/0x20
 do_writepages+0x23/0x2c
 ? do_writepages+0x23/0x2c
 __filemap_fdatawrite_range+0x80/0x87
 filemap_write_and_wait_range+0x67/0x8c
 ext4_sync_file+0x20e/0x472
 vfs_fsync_range+0x8e/0x9f
 ? syscall_trace_enter+0x25b/0x2d0
 vfs_fsync+0x1c/0x1e
 do_fsync+0x31/0x4a
 SyS_fsync+0x10/0x14
 do_syscall_64+0x69/0x131
 entry_SYSCALL64_slow_path+0x25/0x25

We could try to be smart and keep the inline data in this case, or at
least support delayed allocation when allocating the block, but these
solutions would be more complicated and don't seem worthwhile given how
rare this case seems to be.  So just fix the bug by calling
ext4_convert_inline_data() when we're asked to make a page writable, so
that any inline data gets evicted, with the block allocated immediately.

Reported-by: Nick Alcock <nick.alcock@oracle.com>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf auxtrace: Fix no_size logic in addr_filter__resolve_kernel_syms()

commit c3a0bbc7ad7598dec5a204868bdf8a2b1b51df14 upstream.

Address filtering with kernel symbols incorrectly resulted in the error
"Cannot determine size of symbol" because the no_size logic was the wrong
way around.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/1490357752-27942-1-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/hfi1: Prevent kernel QP post send hard lockups

commit b6eac931b9bb2bce4db7032c35b41e5e34ec22a5 upstream.

The driver progress routines can call cond_resched() when
a timeslice is exhausted and irqs are enabled.

If the ULP had been holding a spin lock without disabling irqs and
the post send directly called the progress routine, the cond_resched()
could yield allowing another thread from the same ULP to deadlock
on that same lock.

Correct by replacing the current hfi1_do_send() calldown with a unique
one for post send and adding an argument to hfi1_do_send() to indicate
that the send engine is running in a thread.   If the routine is not
running in a thread, avoid calling cond_resched().

Fixes: Commit 831464ce4b74 ("IB/hfi1: Don't call cond_resched in atomic mode when sending packets")
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx4: Reduce SRIOV multicast cleanup warning message to debug level

commit fb7a91746af18b2ebf596778b38a709cdbc488d3 upstream.

A warning message during SRIOV multicast cleanup should have actually been
a debug level message. The condition generating the warning does no harm
and can fill the message log.

In some cases, during testing, some tests were so intense as to swamp the
message log with these warning messages, causing a stall in the console
message log output task. This stall caused an NMI to be sent to all CPUs
(so that they all dumped their stacks into the message log).
Aside from the message flood causing an NMI, the tests all passed.

Once the message flood which caused the NMI is removed (by reducing the
warning message to debug level), the NMI no longer occurs.

Sample message log (console log) output illustrating the flood and
resultant NMI (snippets with comments and modified with ... instead
of hex digits, to satisfy checkpatch.pl):

 <mlx4_ib> _mlx4_ib_mcg_port_cleanup: ... WARNING: group refcount 1!!!...
 *** About 4000 almost identical lines in less than one second ***
 <mlx4_ib> _mlx4_ib_mcg_port_cleanup: ... WARNING: group refcount 1!!!...
 INFO: rcu_sched detected stalls on CPUs/tasks: { 17} (...)
 *** { 17} above indicates that CPU 17 was the one that stalled ***
 sending NMI to all CPUs:
 ...
 NMI backtrace for cpu 17
 CPU: 17 PID: 45909 Comm: kworker/17:2
 Hardware name: HP ProLiant DL360p Gen8, BIOS P71 09/08/2013
 Workqueue: events fb_flashcursor
 task: ffff880478...... ti: ffff88064e...... task.ti: ffff88064e......
 RIP: 0010:[ffffffff81......]  [ffffffff81......] io_serial_in+0x15/0x20
 RSP: 0018:ffff88064e257cb0  EFLAGS: 00000002
 RAX: 0000000000...... RBX: ffffffff81...... RCX: 0000000000......
 RDX: 0000000000...... RSI: 0000000000...... RDI: ffffffff81......
 RBP: ffff88064e...... R08: ffffffff81...... R09: 0000000000......
 R10: 0000000000...... R11: ffff88064e...... R12: 0000000000......
 R13: 0000000000...... R14: ffffffff81...... R15: 0000000000......
 FS:  0000000000......(0000) GS:ffff8804af......(0000) knlGS:000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080......
 CR2: 00007f2a2f...... CR3: 0000000001...... CR4: 0000000000......
 DR0: 0000000000...... DR1: 0000000000...... DR2: 0000000000......
 DR3: 0000000000...... DR6: 00000000ff...... DR7: 0000000000......
 Stack:
 ffff88064e...... ffffffff81...... ffffffff81...... 0000000000......
 ffffffff81...... ffff88064e...... ffffffff81...... ffffffff81......
 ffffffff81...... ffff88064e...... ffffffff81...... 0000000000......
 Call Trace:
[<ffffffff813d099b>] wait_for_xmitr+0x3b/0xa0
[<ffffffff813d0b5c>] serial8250_console_putchar+0x1c/0x30
[<ffffffff813d0b40>] ? serial8250_console_write+0x140/0x140
[<ffffffff813cb5fa>] uart_console_write+0x3a/0x80
[<ffffffff813d0aae>] serial8250_console_write+0xae/0x140
[<ffffffff8107c4d1>] call_console_drivers.constprop.15+0x91/0xf0
[<ffffffff8107d6cf>] console_unlock+0x3bf/0x400
[<ffffffff813503cd>] fb_flashcursor+0x5d/0x140
[<ffffffff81355c30>] ? bit_clear+0x120/0x120
[<ffffffff8109d5fb>] process_one_work+0x17b/0x470
[<ffffffff8109e3cb>] worker_thread+0x11b/0x400
[<ffffffff8109e2b0>] ? rescuer_thread+0x400/0x400
[<ffffffff810a5aef>] kthread+0xcf/0xe0
[<ffffffff810a5a20>] ? kthread_create_on_node+0x140/0x140
[<ffffffff81645858>] ret_from_fork+0x58/0x90
[<ffffffff810a5a20>] ? kthread_create_on_node+0x140/0x140
Code: 48 89 e5 d3 e6 48 63 f6 48 03 77 10 8b 06 5d c3 66 0f 1f 44 00 00 66 66 66 6

As indicated in the stack trace above, the console output task got swamped.

Fixes: b9c5d6a64358 ("IB/mlx4: Add multicast group (MCG) paravirtualization for SR-IOV")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx4: Fix ib device initialization error flow

commit 99e68909d5aba1861897fe7afc3306c3c81b6de0 upstream.

In mlx4_ib_add, procedure mlx4_ib_alloc_eqs is called to allocate EQs.

However, in the mlx4_ib_add error flow, procedure mlx4_ib_free_eqs is not
called to free the allocated EQs.

Fixes: e605b743f33d ("IB/mlx4: Increase the number of vectors (EQs) available for ULPs")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/IPoIB: ibX: failed to create mcg debug file

commit 771a52584096c45e4565e8aabb596eece9d73d61 upstream.

When udev renames the netdev devices, ipoib debugfs entries does not
get renamed. As a result, if subsequent probe of ipoib device reuse the
name then creating a debugfs entry for the new device would fail.

Also, moved ipoib_create_debug_files and ipoib_delete_debug_files as part
of ipoib event handling in order to avoid any race condition between these.

Fixes: 1732b0ef3b3a ([IPoIB] add path record information in debugfs)
Signed-off-by: Vijay Kumar <vijay.ac.kumar@oracle.com>
Signed-off-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/core: For multicast functions, verify that LIDs are multicast LIDs

commit 8561eae60ff9417a50fa1fb2b83ae950dc5c1e21 upstream.

The Infiniband spec defines "A multicast address is defined by a
MGID and a MLID" (section 10.5).  Currently the MLID value is not
validated.

Add check to verify that the MLID value is in the correct address
range.

Fixes: 0c33aeedb2cf ("[IB] Add checks to multicast attach and detach")
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/core: Fix sysfs registration error flow

commit b312be3d87e4c80872cbea869e569175c5eb0f9a upstream.

The kernel commit cited below restructured ib device management
so that the device kobject is initialized in ib_alloc_device.

As part of the restructuring, the kobject is now initialized in
procedure ib_alloc_device, and is later added to the device hierarchy
in the ib_register_device call stack, in procedure
ib_device_register_sysfs (which calls device_add).

However, in the ib_device_register_sysfs error flow, if an error
occurs following the call to device_add, the cleanup procedure
device_unregister is called. This call results in the device object
being deleted -- which results in various use-after-free crashes.

The correct cleanup call is device_del -- which undoes device_add
without deleting the device object.

The device object will then (correctly) be deleted in the
ib_register_device caller's error cleanup flow, when the caller invokes
ib_dealloc_device.

Fixes: 55aeed06544f6 ("IB/core: Make ib_alloc_device init the kobject")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iov_iter: don't revert iov buffer if csum error

commit a6a5993243550b09f620941dea741b7421fdf79c upstream.

The patch 327868212381 (make skb_copy_datagram_msg() et.al. preserve
->msg_iter on error) will revert the iov buffer if copy to iter
failed, but it didn't copy any datagram if the skb_checksum_complete
error, so no need to revert any data at this place.

v2: Sabrina notice that return -EFAULT when checksum error is not correct
    here, it would confuse the caller about the return value, so fix it.

Fixes: 327868212381 ("make skb_copy_datagram_msg() et.al. preserve->msg_iter on error")
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vfio/type1: Remove locked page accounting workqueue

commit 0cfef2b7410b64d7a430947e0b533314c4f97153 upstream.

If the mmap_sem is contented then the vfio type1 IOMMU backend will
defer locked page accounting updates to a workqueue task.  This has a
few problems and depending on which side the user tries to play, they
might be over-penalized for unmaps that haven't yet been accounted or
race the workqueue to enter more mappings than they're allowed.  The
original intent of this workqueue mechanism seems to be focused on
reducing latency through the ioctl, but we cannot do so at the cost
of correctness.  Remove this workqueue mechanism and update the
callers to allow for failure.  We can also now recheck the limit under
write lock to make sure we don't exceed it.

vfio_pin_pages_remote() also now necessarily includes an unwind path
which we can jump to directly if the consecutive page pinning finds
that we're exceeding the user's memory limits.  This avoids the
current lazy approach which does accounting and mapping up to the
fault, only to return an error on the next iteration to unwind the
entire vfio_dma.

Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Kirti Wankhede <kwankhede@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm thin: fix a memory leak when passing discard bio down

commit 948f581a53b704b984aa20df009f0a2b4cf7f907 upstream.

dm-thin does not free the discard_parent bio after all chained sub
bios finished. The following kmemleak report could be observed after
pool with discard_passdown option processes discard bios in
linux v4.11-rc7. To fix this, we drop the discard_parent bio reference
when its endio (passdown_endio) called.

unreferenced object 0xffff8803d6b29700 (size 256):
  comm "kworker/u8:0", pid 30349, jiffies 4379504020 (age 143002.776s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    01 00 00 00 00 00 00 f0 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff81a5efd9>] kmemleak_alloc+0x49/0xa0
    [<ffffffff8114ec34>] kmem_cache_alloc+0xb4/0x100
    [<ffffffff8110eec0>] mempool_alloc_slab+0x10/0x20
    [<ffffffff8110efa5>] mempool_alloc+0x55/0x150
    [<ffffffff81374939>] bio_alloc_bioset+0xb9/0x260
    [<ffffffffa018fd20>] process_prepared_discard_passdown_pt1+0x40/0x1c0 [dm_thin_pool]
    [<ffffffffa018b409>] break_up_discard_bio+0x1a9/0x200 [dm_thin_pool]
    [<ffffffffa018b484>] process_discard_cell_passdown+0x24/0x40 [dm_thin_pool]
    [<ffffffffa018b24d>] process_discard_bio+0xdd/0xf0 [dm_thin_pool]
    [<ffffffffa018ecf6>] do_worker+0xa76/0xd50 [dm_thin_pool]
    [<ffffffff81086239>] process_one_work+0x139/0x370
    [<ffffffff810867b1>] worker_thread+0x61/0x450
    [<ffffffff8108b316>] kthread+0xd6/0xf0
    [<ffffffff81a6cd1f>] ret_from_fork+0x3f/0x70
    [<ffffffffffffffff>] 0xffffffffffffffff

Signed-off-by: Dennis Yang <dennisyang@qnap.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm rq: check blk_mq_register_dev() return value in dm_mq_init_request_queue()

commit 23a601248958fa4142d49294352fe8d1fdf3e509 upstream.

Otherwise the request-based DM blk-mq request_queue will be put into
service without being properly exported via sysfs.

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm era: save spacemap metadata root after the pre-commit

commit 117aceb030307dcd431fdcff87ce988d3016c34a upstream.

When committing era metadata to disk, it doesn't always save the latest
spacemap metadata root in superblock. Due to this, metadata is getting
corrupted sometimes when reopening the device. The correct order of update
should be, pre-commit (shadows spacemap root), save the spacemap root
(newly shadowed block) to in-core superblock and then the final commit.

Signed-off-by: Somasundaram Krishnasamy <somasundaram.krishnasamy@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: ccp - Change ISR handler method for a v5 CCP

commit 6263b51eb3190d30351360fd168959af7e3a49a9 upstream.

The CCP has the ability to perform several operations simultaneously,
but only one interrupt.  When implemented as a PCI device and using
MSI-X/MSI interrupts, use a tasklet model to service interrupts. By
disabling and enabling interrupts from the CCP, coupled with the
queuing that tasklets provide, we can ensure that all events
(occurring on the device) are recognized and serviced.

This change fixes a problem wherein 2 or more busy queues can cause
notification bits to change state while a (CCP) interrupt is being
serviced, but after the queue state has been evaluated. This results
in the event being 'lost' and the queue hanging, waiting to be
serviced. Since the status bits are never fully de-asserted, the
CCP never generates another interrupt (all bits zero -> one or more
bits one), and no further CCP operations will be executed.

Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>