ASoC: mediatek: mt8173: fix device_node leak

[ Upstream commit 493433785df0075afc0c106ab65f10a605d0b35d ]

Fixes the device_node leak.

Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20211224064719.2031210-2-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

phy: phy-mtk-tphy: add support efuse setting

[ Upstream commit 6f2b033cb883f64ad084a75f13634242c7e179a6 ]

Due to some SoCs have a bit shift issue that will drop a bit for usb3
phy or pcie phy, fix it by adding software efuse reading and setting,
but only support it optionally for version 2/3.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20211218082802.5256-2-chunfeng.yun@mediatek.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: mediatek: mt8192-mt6359: fix device_node leak

[ Upstream commit 4e28491a7a198c668437f2be8a91a76aa52f20eb ]

The of_parse_phandle() document:
    >>> Use of_node_put() on it when done.

The driver didn't call of_node_put().  Fixes the leak.

Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20211214040028.2992627-1-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: mpi3mr: Fixes around reply request queues

[ Upstream commit 243bcc8efdb1f44b1a1d415e6821a246714c68ce ]

Set reply queue depth of 1K for B0 and 4K for A0.

While freeing the segmented request queues use the actual queue depth that
is used while creating them.

Link: https://lore.kernel.org/r/20211220141159.16117-25-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: sr: Don't use GFP_DMA

[ Upstream commit d94d94969a4ba07a43d62429c60372320519c391 ]

The allocated buffers are used as a command payload, for which the block
layer and/or DMA API do the proper bounce buffering if needed.

Link: https://lore.kernel.org/r/20211222090842.920724-1-hch@lst.de
Reported-by: Baoquan He <bhe@redhat.com>
Reviewed-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

MIPS: Octeon: Fix build errors using clang

[ Upstream commit 95339b70677dc6f9a2d669c4716058e71b8dc1c7 ]

A large number of the following errors is reported when compiling
with clang:

  cvmx-bootinfo.h:326:3: error: adding 'int' to a string does not append to the string [-Werror,-Wstring-plus-int]
                  ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_NULL)
                  ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  cvmx-bootinfo.h:321:20: note: expanded from macro 'ENUM_BRD_TYPE_CASE'
          case x: return(#x + 16);        /* Skip CVMX_BOARD_TYPE_ */
                         ~~~^~~~
  cvmx-bootinfo.h:326:3: note: use array indexing to silence this warning
  cvmx-bootinfo.h:321:20: note: expanded from macro 'ENUM_BRD_TYPE_CASE'
          case x: return(#x + 16);        /* Skip CVMX_BOARD_TYPE_ */
                          ^

Follow the prompts to use the address operator '&' to fix this error.

Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests/powerpc: Add a test of sigreturning to the kernel

[ Upstream commit a8968521cfdc3e339fe69473d6632e0aa8d7202a ]

We have a general signal fuzzer, sigfuz, which can modify the MSR & NIP
before sigreturn. But the chance of it hitting a kernel address and also
clearing MSR_PR is fairly slim.

So add a specific test of sigreturn to a kernel address, both with and
without attempting to clear MSR_PR (which the kernel must block).

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211209115944.4062384-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>

i2c: designware-pci: Fix to change data types of hcnt and lcnt parameters

[ Upstream commit d52097010078c1844348dc0e467305e5f90fd317 ]

The data type of hcnt and lcnt in the struct dw_i2c_dev is of type u16.
It's better to have same data type in struct dw_scl_sda_cfg as well.

Reported-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

irqchip/gic-v4: Disable redistributors' view of the VPE table at boot time

[ Upstream commit 79a7f77b9b154d572bd9d2f1eecf58c4d018d8e2 ]

Jay Chen reported that using a kdump kernel on a GICv4.1 system
results in a RAS error being delivered when the secondary kernel
configures the ITS's view of the new VPE table.

As it turns out, that's because each RD still has a pointer to
the previous instance of the VPE table, and that particular
implementation is very upset by seeing two bits of the HW that
should point to the same table with different values.

To solve this, let's invalidate any reference that any RD has to
the VPE table when discovering the RDs. The ITS can then be
programmed as expected.

Reported-by: Jay Chen <jkchen@linux.alibaba.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20211214064716.21407-1-jkchen@linux.alibaba.com
Link: https://lore.kernel.org/r/20211216144804.1578566-1-maz@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

MIPS: OCTEON: add put_device() after of_find_device_by_node()

[ Upstream commit 858779df1c0787d3fec827fb705708df9ebdb15b ]

This was found by coccicheck:
./arch/mips/cavium-octeon/octeon-platform.c, 332, 1-7, ERROR missing
put_device; call of_find_device_by_node on line 324, but without a
corresponding object release within this function.
./arch/mips/cavium-octeon/octeon-platform.c, 395, 1-7, ERROR missing
put_device; call of_find_device_by_node on line 387, but without a
corresponding object release within this function.
./arch/mips/cavium-octeon/octeon-usb.c, 512, 3-9, ERROR missing
put_device; call of_find_device_by_node on line 515, but without a
corresponding object release within this function.
./arch/mips/cavium-octeon/octeon-usb.c, 543, 1-7, ERROR missing
put_device; call of_find_device_by_node on line 515, but without a
corresponding object release within this function.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

udf: Fix error handling in udf_new_inode()

[ Upstream commit f05f2429eec60851b98bdde213de31dab697c01b ]

When memory allocation of iinfo or block allocation fails, already
allocated struct udf_inode_info gets freed with iput() and
udf_evict_inode() may look at inode fields which are not properly
initialized. Fix it by marking inode bad before dropping reference to it
in udf_new_inode().

Reported-by: syzbot+9ca499bb57a2b9e4c652@syzkaller.appspotmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/fadump: Fix inaccurate CPU state info in vmcore generated with panic

[ Upstream commit 06e629c25daa519be620a8c17359ae8fc7a2e903 ]

In panic path, fadump is triggered via a panic notifier function.
Before calling panic notifier functions, smp_send_stop() gets called,
which stops all CPUs except the panic'ing CPU. Commit 8389b37dffdc
("powerpc: stop_this_cpu: remove the cpu from the online map.") and
again commit bab26238bbd4 ("powerpc: Offline CPU in stop_this_cpu()")
started marking CPUs as offline while stopping them. So, if a kernel
has either of the above commits, vmcore captured with fadump via panic
path would not process register data for all CPUs except the panic'ing
CPU. Sample output of crash-utility with such vmcore:

  # crash vmlinux vmcore
  ...
        KERNEL: vmlinux
      DUMPFILE: vmcore  [PARTIAL DUMP]
          CPUS: 1
          DATE: Wed Nov 10 09:56:34 EST 2021
        UPTIME: 00:00:42
  LOAD AVERAGE: 2.27, 0.69, 0.24
         TASKS: 183
      NODENAME: XXXXXXXXX
       RELEASE: 5.15.0+
       VERSION: #974 SMP Wed Nov 10 04:18:19 CST 2021
       MACHINE: ppc64le  (2500 Mhz)
        MEMORY: 8 GB
         PANIC: "Kernel panic - not syncing: sysrq triggered crash"
           PID: 3394
       COMMAND: "bash"
          TASK: c0000000150a5f80  [THREAD_INFO: c0000000150a5f80]
           CPU: 1
         STATE: TASK_RUNNING (PANIC)

  crash> p -x __cpu_online_mask
  __cpu_online_mask = $1 = {
    bits = {0x2, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0}
  }
  crash>
  crash>
  crash> p -x __cpu_active_mask
  __cpu_active_mask = $2 = {
    bits = {0xff, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0}
  }
  crash>

While this has been the case since fadump was introduced, the issue
was not identified for two probable reasons:

  - In general, the bulk of the vmcores analyzed were from crash
    due to exception.

  - The above did change since commit 8341f2f222d7 ("sysrq: Use
    panic() to force a crash") started using panic() instead of
    deferencing NULL pointer to force a kernel crash. But then
    commit de6e5d38417e ("powerpc: smp_send_stop do not offline
    stopped CPUs") stopped marking CPUs as offline till kernel
    commit bab26238bbd4 ("powerpc: Offline CPU in stop_this_cpu()")
    reverted that change.

To ensure post processing register data of all other CPUs happens
as intended, let panic() function take the crash friendly path (read
crash_smp_send_stop()) with the help of crash_kexec_post_notifiers
option. Also, as register data for all CPUs is captured by f/w, skip
IPI callbacks here for fadump, to avoid any complications in finding
the right backtraces.

Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211207103719.91117-2-hbathini@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc: handle kdump appropriately with crash_kexec_post_notifiers option

[ Upstream commit 219572d2fc4135b5ce65c735d881787d48b10e71 ]

Kdump can be triggered after panic_notifers since commit f06e5153f4ae2
("kernel/panic.c: add "crash_kexec_post_notifiers" option for kdump
after panic_notifers") introduced crash_kexec_post_notifiers option.
But using this option would mean smp_send_stop(), that marks all other
CPUs as offline, gets called before kdump is triggered. As a result,
kdump routines fail to save other CPUs' registers. To fix this, kdump
friendly crash_smp_send_stop() function was introduced with kernel
commit 0ee59413c967 ("x86/panic: replace smp_send_stop() with kdump
friendly version in panic path"). Override this kdump friendly weak
function to handle crash_kexec_post_notifiers option appropriately
on powerpc.

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
[Fixed signature of crash_stop_this_cpu() - reported by lkp@intel.com]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211207103719.91117-1-hbathini@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests/powerpc/spectre_v2: Return skip code when miss_percent is high

[ Upstream commit 3c42e9542050d49610077e083c7c3f5fd5e26820 ]

A mis-match between reported and actual mitigation is not restricted to the
Vulnerable case. The guest might also report the mitigation as "Software
count cache flush" and the host will still mitigate with branch cache
disabled.

So, instead of skipping depending on the detected mitigation, simply skip
whenever the detected miss_percent is the expected one for a fully
mitigated system, that is, above 95%.

Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211207130557.40566-1-cascardo@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/40x: Map 32Mbytes of memory at startup

[ Upstream commit 06e7cbc29e97b4713b4ea6def04ae8501a7d1a59 ]

As reported by Carlo, 16Mbytes is not enough with modern kernels
that tend to be a bit big, so map another 16M page at boot.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/89b5f974a7fa5011206682cd092e2c905530ff46.1632755552.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>

MIPS: Loongson64: Use three arguments for slti

[ Upstream commit f2c6c22fa83ab2577619009057b3ebcb5305bb03 ]

LLVM's integrated assembler does not support 'slti <reg>, <imm>':

<instantiation>:16:12: error: invalid operand for instruction
 slti $12, (0x6300 | 0x0008)
           ^
arch/mips/kernel/head.S:86:2: note: while in macro instantiation
 kernel_entry_setup # cpu specific setup
 ^
<instantiation>:16:12: error: invalid operand for instruction
 slti $12, (0x6300 | 0x0008)
           ^
arch/mips/kernel/head.S:150:2: note: while in macro instantiation
 smp_slave_setup
 ^

To increase compatibility with LLVM's integrated assembler, use the full
form of 'slti <reg>, <reg>, <imm>', which matches the rest of
arch/mips/. This does not result in any change for GNU as.

Link: https://github.com/ClangBuiltLinux/linux/issues/1526
Reported-by: Ryutaroh Matsumoto <ryutaroh@ict.e.titech.ac.jp>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: seq: Set upper limit of processed events

[ Upstream commit 6fadb494a638d8b8a55864ecc6ac58194f03f327 ]

Currently ALSA sequencer core tries to process the queued events as
much as possible when they become dispatchable.  If applications try
to queue too massive events to be processed at the very same timing,
the sequencer core would still try to process such all events, either
in the interrupt context or via some notifier; in either away, it
might be a cause of RCU stall or such problems.

As a potential workaround for those problems, this patch adds the
upper limit of the amount of events to be processed.  The remaining
events are processed in the next batch, so they won't be lost.

For the time being, it's limited up to 1000 events per queue, which
should be high enough for any normal usages.

Reported-by: Zqiang <qiang.zhang1211@gmail.com>
Reported-by: syzbot+bb950e68b400ab4f65f8@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20211102033222.3849-1-qiang.zhang1211@gmail.com
Link: https://lore.kernel.org/r/20211207165146.2888-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: lpfc: Trigger SLI4 firmware dump before doing driver cleanup

[ Upstream commit 7dd2e2a923173d637c272e483966be8e96a72b64 ]

Extraneous teardown routines are present in the firmware dump path causing
altered states in firmware captures.

When a firmware dump is requested via sysfs, trigger the dump immediately
without tearing down structures and changing adapter state.

The driver shall rely on pre-existing firmware error state clean up
handlers to restore the adapter.

Link: https://lore.kernel.org/r/20211204002644.116455-6-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: lpfc: Fix leaked lpfc_dmabuf mbox allocations with NPIV

[ Upstream commit f0d3919697492950f57a26a1093aee53880d669d ]

During rmmod testing, messages appeared indicating lpfc_mbuf_pool entries
were still busy. This situation was only seen doing rmmod after at least 1
vport (NPIV) instance was created and destroyed. The number of messages
scaled with the number of vports created.

When a vport is created, it can receive a PLOGI from another initiator
Nport.  When this happens, the driver prepares to ack the PLOGI and
prepares an RPI for registration (via mbx cmd) which includes an mbuf
allocation. During the unsolicited PLOGI processing and after the RPI
preparation, the driver recognizes it is one of the vport instances and
decides to reject the PLOGI. During the LS_RJT preparation for the PLOGI,
the mailbox struct allocated for RPI registration is freed, but the mbuf
that was also allocated is not released.

Fix by freeing the mbuf with the mailbox struct in the LS_RJT path.

As part of the code review to figure the issue out a couple of other areas
where found that also would not have released the mbuf. Those are cleaned
up as well.

Link: https://lore.kernel.org/r/20211204002644.116455-2-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: ufs: Fix a kernel crash during shutdown

[ Upstream commit 3489c34bd02b73a72646037d673a122a53cee174 ]

Fix the following kernel crash:

Unable to handle kernel paging request at virtual address ffffffc91e735000
Call trace:
 __queue_work+0x26c/0x624
 queue_work_on+0x6c/0xf0
 ufshcd_hold+0x12c/0x210
 __ufshcd_wl_suspend+0xc0/0x400
 ufshcd_wl_shutdown+0xb8/0xcc
 device_shutdown+0x184/0x224
 kernel_restart+0x4c/0x124
 __arm64_sys_reboot+0x194/0x264
 el0_svc_common+0xc8/0x1d4
 do_el0_svc+0x30/0x8c
 el0_svc+0x20/0x30
 el0_sync_handler+0x84/0xe4
 el0_sync+0x1bc/0x1c0

Fix this crash by ungating the clock before destroying the work queue on
which clock gating work is queued.

Link: https://lore.kernel.org/r/20211203231950.193369-15-bvanassche@acm.org
Tested-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

interconnect: qcom: rpm: Prevent integer overflow in rate

[ Upstream commit a7d9436a6c85fcb8843c910fd323dcd7f839bf63 ]

Using icc-rpm on ARM32 currently results in clk_set_rate() errors during
boot, e.g. "bus clk_set_rate error: -22". This is very similar to commit
7381e27b1e56 ("interconnect: qcom: msm8974: Prevent integer overflow in rate")
where the u64 is converted to a signed long during clock rate rounding,
resulting in an overflow on 32-bit platforms.

Let's fix it similarly by making sure that the rate does not exceed
LONG_MAX. Such high clock rates will surely result in the maximum
frequency of the bus anyway.

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20211206114542.45325-1-stephan@gerhold.net
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dm: fix alloc_dax error handling in alloc_dev

[ Upstream commit d751939235b9b7bc4af15f90a3e99288a8b844a7 ]

Make sure ->dax_dev is NULL on error so that the cleanup path doesn't
trip over an ERR_PTR.

Reported-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20211129102203.2243509-2-hch@lst.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvmem: core: set size for sysfs bin file

[ Upstream commit 86192251033308bb42f1e9813c962989d8ed07ec ]

For some reason we never set the size for nvmem sysfs binary file.
Set this.

Reported-by: Gilles BULOZ <gilles.buloz@kontron.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211130133909.6154-1-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

w1: Misuse of get_user()/put_user() reported by sparse

[ Upstream commit 33dc3e3e99e626ce51f462d883b05856c6c30b1d ]

sparse warnings: (new ones prefixed by >>)
>> drivers/w1/slaves/w1_ds28e04.c:342:13: sparse: sparse: incorrect type in initializer (different address spaces) @@     expected char [noderef] __user *_pu_addr @@     got char *buf @@
   drivers/w1/slaves/w1_ds28e04.c:342:13: sparse:     expected char [noderef] __user *_pu_addr
   drivers/w1/slaves/w1_ds28e04.c:342:13: sparse:     got char *buf
>> drivers/w1/slaves/w1_ds28e04.c:356:13: sparse: sparse: incorrect type in initializer (different address spaces) @@     expected char const [noderef] __user *_gu_addr @@     got char const *buf @@
   drivers/w1/slaves/w1_ds28e04.c:356:13: sparse:     expected char const [noderef] __user *_gu_addr
   drivers/w1/slaves/w1_ds28e04.c:356:13: sparse:     got char const *buf

The buffer buf is a failsafe buffer in kernel space, it's not user
memory hence doesn't deserve the use of get_user() or put_user().

Access 'buf' content directly.

Link: https://lore.kernel.org/lkml/202111190526.K5vb7NWC-lkp@intel.com/T/
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/d14ed8d71ad4372e6839ae427f91441d3ba0e94d.1637946316.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: PPC: Book3S: Suppress failed alloc warning in H_COPY_TOFROM_GUEST

[ Upstream commit 792020907b11c6f9246c21977cab3bad985ae4b6 ]

H_COPY_TOFROM_GUEST is an hcall for an upper level VM to access its nested
VMs memory. The userspace can trigger WARN_ON_ONCE(!(gfp & __GFP_NOWARN))
in __alloc_pages() by constructing a tiny VM which only does
H_COPY_TOFROM_GUEST with a too big GPR9 (number of bytes to copy).

This silences the warning by adding __GFP_NOWARN.

Spotted by syzkaller.

Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210901084550.1658699-1-aik@ozlabs.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: PPC: Book3S: Suppress warnings when allocating too big memory slots

[ Upstream commit 511d25d6b789fffcb20a3eb71899cf974a31bd9d ]

The userspace can trigger "vmalloc size %lu allocation failure: exceeds
total pages" via the KVM_SET_USER_MEMORY_REGION ioctl.

This silences the warning by checking the limit before calling vzalloc()
and returns ENOMEM if failed.

This does not call underlying valloc helpers as __vmalloc_node() is only
exported when CONFIG_TEST_VMALLOC_MODULE and __vmalloc_node_range() is
not exported at all.

Spotted by syzkaller.

Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[mpe: Use 'size' for the variable rather than 'cb']
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210901084512.1658628-1-aik@ozlabs.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/powermac: Add missing lockdep_register_key()

[ Upstream commit df1f679d19edb9eeb67cc2f96b29375f21991945 ]

KeyWest i2c @0xf8001003 irq 42 /uni-n@f8000000/i2c@f8001000
BUG: key c2d00cbc has not been registered!
------------[ cut here ]------------
DEBUG_LOCKS_WARN_ON(1)
WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:4801 lockdep_init_map_type+0x4c0/0xb4c
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.15.5-gentoo-PowerMacG4 #9
NIP:  c01a9428 LR: c01a9428 CTR: 00000000
REGS: e1033cf0 TRAP: 0700   Not tainted  (5.15.5-gentoo-PowerMacG4)
MSR:  00029032 <EE,ME,IR,DR,RI>  CR: 24002002  XER: 00000000

GPR00: c01a9428 e1033db0 c2d1cf20 00000016 00000004 00000001 c01c0630 e1033a73
GPR08: 00000000 00000000 00000000 e1033db0 24002004 00000000 f8729377 00000003
GPR16: c1829a9c 00000000 18305357 c1416fc0 c1416f80 c006ac60 c2d00ca8 c1416f00
GPR24: 00000000 c21586f0 c2160000 00000000 c2d00cbc c2170000 c216e1a0 c2160000
NIP [c01a9428] lockdep_init_map_type+0x4c0/0xb4c
LR [c01a9428] lockdep_init_map_type+0x4c0/0xb4c
Call Trace:
[e1033db0] [c01a9428] lockdep_init_map_type+0x4c0/0xb4c (unreliable)
[e1033df0] [c1c177b8] kw_i2c_add+0x334/0x424
[e1033e20] [c1c18294] pmac_i2c_init+0x9ec/0xa9c
[e1033e80] [c1c1a790] smp_core99_probe+0xbc/0x35c
[e1033eb0] [c1c03cb0] kernel_init_freeable+0x190/0x5a4
[e1033f10] [c000946c] kernel_init+0x28/0x154
[e1033f30] [c0035148] ret_from_kernel_thread+0x14/0x1c

Add missing lockdep_register_key()

Reported-by: Erhard Furtner <erhard_f@mailbox.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/69e4f55565bb45ebb0843977801b245af0c666fe.1638264741.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: meson: gxbb: Fix the SDM_EN bit for MPLL0 on GXBB

[ Upstream commit ff54938dd190d85f740b9bf9dde59b550936b621 ]

There are reports that 48kHz audio does not work on the WeTek Play 2
(which uses a GXBB SoC), while 44.1kHz audio works fine on the same
board. There are also reports of 48kHz audio working fine on GXL and
GXM SoCs, which are using an (almost) identical AIU (audio controller).

Experimenting has shown that MPLL0 is causing this problem. In the .dts
we have by default:
assigned-clocks = <&clkc CLKID_MPLL0>,
  <&clkc CLKID_MPLL1>,
  <&clkc CLKID_MPLL2>;
assigned-clock-rates = <294912000>,
       <270950400>,
       <393216000>;
The MPLL0 rate is divisible by 48kHz without remainder and the MPLL1
rate is divisible by 44.1kHz without remainder. Swapping these two clock
rates "fixes" 48kHz audio but breaks 44.1kHz audio.

Everything looks normal when looking at the info provided by the common
clock framework while playing 48kHz audio (via I2S with mclk-fs = 256):
        mpll_prediv                 1        1        0  2000000000
           mpll0_div                1        1        0   294909641
              mpll0                 1        1        0   294909641
                 cts_amclk_sel       1        1        0   294909641
                    cts_amclk_div       1        1        0    12287902
                       cts_amclk       1        1        0    12287902

meson-clk-msr however shows that the actual MPLL0 clock is off by more
than 38MHz:
        mp0_out               333322917    +/-10416Hz

The rate seen by meson-clk-msr is very close to what we would get when
SDM (the fractional part) was ignored:
  (2000000000Hz * 16384) / ((16384 * 6) = 333.33MHz
If SDM was considered the we should get close to:
  (2000000000Hz * 16384) / ((16384 * 6) + 12808) = 294.9MHz

Further experimenting shows that HHI_MPLL_CNTL7[15] does not have any
effect on the rate of MPLL0 as seen my meson-clk-msr (regardless of
whether that bit is zero or one the rate is always the same according to
meson-clk-msr). Using HHI_MPLL_CNTL[25] on the other hand as SDM_EN
results in SDM being considered for the rate output by the hardware. The
rate - as seen by meson-clk-msr - matches with what we expect when
SDM_EN is enabled (fractional part is being considered, resulting in a
294.9MHz output) or disable (fractional part being ignored, resulting in
a 333.33MHz output).

Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20211031135006.1508796-1-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

i2c: mpc: Correct I2C reset procedure

[ Upstream commit ebe82cf92cd4825c3029434cabfcd2f1780e64be ]

Current I2C reset procedure is broken in two ways:
1) It only generate 1 START instead of 9 STARTs and STOP.
2) It leaves the bus Busy so every I2C xfer after the first
   fixup calls the reset routine again, for every xfer there after.

This fixes both errors.

Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/smp: Move setup_profiling_timer() under CONFIG_PROFILING

[ Upstream commit a4ac0d249a5db80e79d573db9e4ad29354b643a8 ]

setup_profiling_timer() is only needed when CONFIG_PROFILING is enabled.

Fixes the following W=1 warning when CONFIG_PROFILING=n:
  linux/arch/powerpc/kernel/smp.c:1638:5: error: no previous prototype for ‘setup_profiling_timer’

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211124093254.1054750-5-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>

i2c: i801: Don't silently correct invalid transfer size

[ Upstream commit effa453168a7eeb8a562ff4edc1dbf9067360a61 ]

If an invalid block size is provided, reject it instead of silently
changing it to a supported value. Especially critical I see the case of
a write transfer with block length 0. In this case we have no guarantee
that the byte we would write is valid. When silently reducing a read to
32 bytes then we don't return an error and the caller may falsely
assume that we returned the full requested data.

If this change should break any (broken) caller, then I think we should
fix the caller.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: imx-hdmi: add put_device() after of_find_device_by_node()

[ Upstream commit f670b274f7f6f4b2722d7f08d0fddf606a727e92 ]

This was found by coccicheck:
./sound/soc/fsl/imx-hdmi.c,209,1-7,ERROR  missing put_device; call
of_find_device_by_node on line 119, but without a corresponding object
release within this function.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Link: https://lore.kernel.org/r/20211110002910.134915-1-ye.guojin@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/watchdog: Fix missed watchdog reset due to memory ordering race

[ Upstream commit 5dad4ba68a2483fc80d70b9dc90bbe16e1f27263 ]

It is possible for all CPUs to miss the pending cpumask becoming clear,
and then nobody resetting it, which will cause the lockup detector to
stop working. It will eventually expire, but watchdog_smp_panic will
avoid doing anything if the pending mask is clear and it will never be
reset.

Order the cpumask clear vs the subsequent test to close this race.

Add an extra check for an empty pending mask when the watchdog fires and
finds its bit still clear, to try to catch any other possible races or
bugs here and keep the watchdog working. The extra test in
arch_touch_nmi_watchdog is required to prevent the new warning from
firing off.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Laurent Dufour <ldufour@linux.ibm.com>
Debugged-by: Laurent Dufour <ldufour@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211110025056.2084347-2-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/btext: add missing of_node_put

[ Upstream commit a1d2b210ffa52d60acabbf7b6af3ef7e1e69cda0 ]

for_each_node_by_type performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.

A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):

// <smpl>
@@
local idexpression n;
expression e;
@@

 for_each_node_by_type(n,...) {
   ...
(
   of_node_put(n);
|
   e = n
|
+  of_node_put(n);
?  break;
)
   ...
 }
... when != n
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1448051604-25256-6-git-send-email-Julia.Lawall@lip6.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/cell: add missing of_node_put

[ Upstream commit a841fd009e51c8c0a8f07c942e9ab6bb48da8858 ]

for_each_node_by_name performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.

A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):

// <smpl>
@@
expression e,e1;
local idexpression n;
@@

 for_each_node_by_name(n, e1) {
   ... when != of_node_put(n)
       when != e = n
(
   return n;
|
+  of_node_put(n);
?  return ...;
)
   ...
 }
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1448051604-25256-7-git-send-email-Julia.Lawall@lip6.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/powernv: add missing of_node_put

[ Upstream commit 7d405a939ca960162eb30c1475759cb2fdf38f8c ]

for_each_compatible_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.

A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):

// <smpl>
@@
local idexpression n;
expression e;
@@

 for_each_compatible_node(n,...) {
   ...
(
   of_node_put(n);
|
   e = n
|
+  of_node_put(n);
?  break;
)
   ...
 }
... when != n
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1448051604-25256-4-git-send-email-Julia.Lawall@lip6.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/6xx: add missing of_node_put

[ Upstream commit f6e82647ff71d427d4148964b71f239fba9d7937 ]

for_each_compatible_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.

A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):

// <smpl>
@@
expression e;
local idexpression n;
@@

@@
local idexpression n;
expression e;
@@

 for_each_compatible_node(n,...) {
   ...
(
   of_node_put(n);
|
   e = n
|
+  of_node_put(n);
?  break;
)
   ...
 }
... when != n
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1448051604-25256-2-git-send-email-Julia.Lawall@lip6.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/kbuild: Enable CONFIG_KALLSYMS_ALL=y in the defconfigs

[ Upstream commit b6aa86cff44cf099299d3a5e66348cb709cd7964 ]

Most distro kernels have this option enabled, to improve debug output.

Lockdep also selects it.

Enable this in the defconfig kernel as well, to make it more
representative of what people are using on x86.

Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/YdTn7gssoMVDMgMw@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: flexcan: add more quirks to describe RX path capabilities

[ Upstream commit c5c88591040ee7d84d037328eed9019d3ffab821 ]

Most flexcan IP cores support 2 RX modes:
- FIFO
- mailbox

Some IP core versions cannot receive CAN RTR messages via mailboxes.
This patch adds quirks to document this.

This information will be used in a later patch to switch from FIFO to
more performant mailbox mode at the expense of losing the ability to
receive RTR messages. This trade off is beneficial in certain use
cases.

Link: https://lore.kernel.org/all/20220107193105.1699523-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: flexcan: rename RX modes

[ Upstream commit 34ea4e1c99f1f177f87e4ae7896caef238dd741a ]

Most flexcan IP cores support 2 RX modes:
- FIFO
- mailbox

The names for these modes were chosen to reflect the name of the
rx-offload mode they are using.

The name of the RX modes should better reflect their difference with
regards the flexcan IP core. So this patch renames the various
occurrences of OFF_FIFO to RX_FIFO and OFF_TIMESTAMP to RX_MAILBOX:

| FLEXCAN_TX_MB_RESERVED_OFF_FIFO -> FLEXCAN_TX_MB_RESERVED_RX_FIFO
| FLEXCAN_TX_MB_RESERVED_OFF_TIMESTAMP -> FLEXCAN_TX_MB_RESERVED_RX_MAILBOX
| FLEXCAN_QUIRK_USE_OFF_TIMESTAMP -> FLEXCAN_QUIRK_USE_RX_MAILBOX

Link: https://lore.kernel.org/all/20220107193105.1699523-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: flexcan: allow to change quirks at runtime

[ Upstream commit 01bb4dccd92b4dc21f6af3312e5696924e371111 ]

This is a preparation patch for the upcoming support to change the
rx-rtr capability via the ethtool API.

Link: https://lore.kernel.org/all/20220107193105.1699523-3-mkl@pengutronix.de
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

parisc: Avoid calling faulthandler_disabled() twice

[ Upstream commit 9e9d4b460f23bab61672eae397417d03917d116c ]

In handle_interruption(), we call faulthandler_disabled() to check whether the
fault handler is not disabled. If the fault handler is disabled, we immediately
call do_page_fault(). It then calls faulthandler_disabled(). If disabled,
do_page_fault() attempts to fixup the exception by jumping to no_context:

no_context:

        if (!user_mode(regs) && fixup_exception(regs)) {
                return;
        }

        parisc_terminate("Bad Address (null pointer deref?)", regs, code, address);

Apart from the error messages, the two blocks of code perform the same
function.

We can avoid two calls to faulthandler_disabled() by a simple revision
to the code in handle_interruption().

Note: I didn't try to fix the formatting of this code block.

Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5e: Unblock setting vid 0 for VF in case PF isn't eswitch manager

[ Upstream commit 7846665d3504812acaebf920d1141851379a7f37 ]

When using libvirt to passthrough VF to VM it will always set the VF vlan
to 0 even if user didn’t request it, this will cause libvirt to fail to
boot in case the PF isn't eswitch owner.

Example of such case is the DPU host PF which isn't eswitch manager, so
any attempt to passthrough VF of it using libvirt will fail.

Fix it by not returning error in case set VF vlan is called with vid 0.

Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5: Update log_max_qp value to FW max capability

[ Upstream commit f79a609ea6bf54ad2d2c24e4de4524288b221666 ]

log_max_qp in driver's default profile #2 was set to 18, but FW actually
supports 17 at the most - a situation that led to the concerning print
when the driver is loaded:
"log_max_qp value in current profile is 18, changing to HCA capabaility
limit (17)"

The expected behavior from mlx5_profile #2 is to match the maximum FW
capability in regards to log_max_qp. Thus, log_max_qp in profile #2 is
initialized to a defined static value (0xff) - which basically means that
when loading this profile, log_max_qp value  will be what the currently
installed FW supports at most.

Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

random: do not throw away excess input to crng_fast_load

[ Upstream commit 73c7733f122e8d0107f88655a12011f68f69e74b ]

When crng_fast_load() is called by add_hwgenerator_randomness(), we
currently will advance to crng_init==1 once we've acquired 64 bytes, and
then throw away the rest of the buffer. Usually, that is not a problem:
When add_hwgenerator_randomness() gets called via EFI or DT during
setup_arch(), there won't be any IRQ randomness. Therefore, the 64 bytes
passed by EFI exactly matches what is needed to advance to crng_init==1.
Usually, DT seems to pass 64 bytes as well -- with one notable exception
being kexec, which hands over 128 bytes of entropy to the kexec'd kernel.
In that case, we'll advance to crng_init==1 once 64 of those bytes are
consumed by crng_fast_load(), but won't continue onward feeding in bytes
to progress to crng_init==2. This commit fixes the issue by feeding
any leftover bytes into the next phase in add_hwgenerator_randomness().

[linux@dominikbrodowski.net: rewrite commit message]
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

serial: core: Keep mctrl register state and cached copy in sync

[ Upstream commit 93a770b7e16772530196674ffc79bb13fa927dc6 ]

struct uart_port contains a cached copy of the Modem Control signals.
It is used to skip register writes in uart_update_mctrl() if the new
signal state equals the old signal state.  It also avoids a register
read to obtain the current state of output signals.

When a uart_port is registered, uart_configure_port() changes signal
state but neglects to keep the cached copy in sync.  That may cause
a subsequent register write to be incorrectly skipped.  Fix it before
it trips somebody up.

This behavior has been present ever since the serial core was introduced
in 2002:
https://git.kernel.org/history/history/c/33c0d1b0c3eb

So far it was never an issue because the cached copy is initialized to 0
by kzalloc() and when uart_configure_port() is executed, at most DTR has
been set by uart_set_options() or sunsu_console_setup().  Therefore,
a stable designation seems unnecessary.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/bceeaba030b028ed810272d55d5fc6f3656ddddb.1641129752.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

serial: pl011: Drop CR register reset on set_termios

[ Upstream commit e368cc656fd6d0075f1c3ab9676e2001451e3e04 ]

pl011_set_termios() briefly resets the CR register to zero, thereby
glitching DTR/RTS signals.  With rs485 this may result in the bus being
occupied for no reason.

Where does this register write originate from?

The PL011 driver was forked from the PL010 driver in 2004:
https://git.kernel.org/history/history/c/157c0342e591

Until this commit, the PL010 driver's IRQ handler ambauart_int()
modified the CR register without holding the port spinlock.

ambauart_set_termios() also modified that register.  To prevent
concurrent read-modify-writes by the IRQ handler and to prevent
transmission while changing baudrate, ambauart_set_termios() had to
disable interrupts.  On the PL010, that is achieved by writing zero to
the CR register.

However, on the PL011, interrupts are disabled in the IMSC register,
not in the CR register.

Additionally, the commit amended both the PL010 and PL011 driver to
acquire the port spinlock in the IRQ handler, obviating the need to
disable interrupts in ->set_termios().

So the CR register write is obsolete for two reasons.  Drop it.

Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/f49f945375f5ccb979893c49f1129f51651ac738.1641129062.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

serial: pl010: Drop CR register reset on set_termios

[ Upstream commit 08a0c6dff91c965e39905cf200d22db989203ccb ]

pl010_set_termios() briefly resets the CR register to zero.

Where does this register write come from?

The PL010 driver's IRQ handler ambauart_int() originally modified the CR
register without holding the port spinlock.  ambauart_set_termios() also
modified that register.  To prevent concurrent read-modify-writes by the
IRQ handler and to prevent transmission while changing baudrate,
ambauart_set_termios() had to disable interrupts.  That is achieved by
writing zero to the CR register.

However in 2004 the PL010 driver was amended to acquire the port
spinlock in the IRQ handler, obviating the need to disable interrupts in
->set_termios():
https://git.kernel.org/history/history/c/157c0342e591

That rendered the CR register write obsolete.  Drop it.

Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/fcaff16e5b1abb4cc3da5a2879ac13f278b99ed0.1641128728.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

regulator: qcom_smd: Align probe function with rpmh-regulator

[ Upstream commit 14e2976fbabdacb01335d7f91eeebbc89c67ddb1 ]

The RPMh regulator driver is much newer and gets more attention, which in
consequence makes it do a few things better. Update qcom_smd-regulator's
probe function to mimic what rpmh-regulator does to address a couple of
issues:

- Probe defer now works correctly, before it used to, well,
  kinda just die.. This fixes reliable probing on (at least) PM8994,
  because Linux apparently cannot deal with supply map dependencies yet..

- Regulator data is now matched more sanely: regulator data is matched
  against each individual regulator node name and throwing an -EINVAL if
  data is missing, instead of just assuming everything is fine and
  iterating over all subsequent array members.

- status = "disabled" will now work for disabling individual regulators in
  DT. Previously it didn't seem to do much if anything at all.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20211230023442.1123424-1-konrad.dybcio@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: gemini: allow any RGMII interface mode

[ Upstream commit 4e4f325a0a55907b14f579e6b1a38c53755e3de2 ]

The four RGMII interface modes take care of the required RGMII delay
configuration at the PHY and should not be limited by the network MAC
driver. Sadly, gemini was only permitting RGMII mode with no delays,
which would require the required delay to be inserted via PCB tracking
or by the MAC.

However, there are designs that require the PHY to add the delay, which
is impossible without Gemini permitting the other three PHY interface
modes. Fix the driver to allow these.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Link: https://lore.kernel.org/r/E1n4mpT-002PLd-Ha@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: phy: marvell: configure RGMII delays for 88E1118

[ Upstream commit f22725c95ececb703c3f741e8f946d23705630b7 ]

Corentin Labbe reports that the SSI 1328 does not work when allowing
the PHY to operate at gigabit speeds, but does work with the generic
PHY driver.

This appears to be because m88e1118_config_init() writes a fixed value
to the MSCR register, claiming that this is to enable 1G speeds.
However, this always sets bits 4 and 5, enabling RGMII transmit and
receive delays. The suspicion is that the original board this was
added for required the delays to make 1G speeds work.

Add the necessary configuration for RGMII delays for the 88E1118 to
bring this into line with the requirements for RGMII support, and thus
make the SSI 1328 work.

Corentin Labbe has tested this on gemini-ssi1328 and gemini-ns2502.

Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mlxsw: pci: Avoid flow control for EMAD packets

[ Upstream commit d43e4271747ace01a27a49a97a397cb4219f6487 ]

Locally generated packets ingress the device through its CPU port. When
the CPU port is congested and there are not enough credits in its
headroom buffer, packets can be dropped.

While this might be acceptable for data packets that traverse the
network, configuration packets exchanged between the host and the device
(EMADs) should not be subjected to this flow control.

The "sdq_lp" bit in the SDQ (Send Descriptor Queue) context allows the
host to instruct the device to treat packets sent on this queue as
"local processing" and always process them, regardless of the state of
the CPU port's headroom.

Add the definition of this bit and set it for the dedicated SDQ reserved
for the transmission of EMAD packets. This makes the "local processing"
bit in the WQE (Work Queue Element) redundant, so clear it.

Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf/selftests: Fix namespace mount setup in tc_redirect

[ Upstream commit 5e22dd18626726028a93ff1350a8a71a00fd843d ]

The tc_redirect umounts /sys in the new namespace, which can be
mounted as shared and cause global umount. The lazy umount also
takes down mounted trees under /sys like debugfs, which won't be
available after sysfs mounts again and could cause fails in other
tests.

  # cat /proc/self/mountinfo | grep debugfs
  34 23 0:7 / /sys/kernel/debug rw,nosuid,nodev,noexec,relatime shared:14 - debugfs debugfs rw
  # cat /proc/self/mountinfo | grep sysfs
  23 86 0:22 / /sys rw,nosuid,nodev,noexec,relatime shared:2 - sysfs sysfs rw
  # mount | grep debugfs
  debugfs on /sys/kernel/debug type debugfs (rw,nosuid,nodev,noexec,relatime)

  # ./test_progs -t tc_redirect
  #164 tc_redirect:OK
  Summary: 1/4 PASSED, 0 SKIPPED, 0 FAILED

  # mount | grep debugfs
  # cat /proc/self/mountinfo | grep debugfs
  # cat /proc/self/mountinfo | grep sysfs
  25 86 0:22 / /sys rw,relatime shared:2 - sysfs sysfs rw

Making the sysfs private under the new namespace so the umount won't
trigger the global sysfs umount.

Reported-by: Hangbin Liu <haliu@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jussi Maki <joamaki@gmail.com>
Link: https://lore.kernel.org/bpf/20220104121030.138216-1-jolsa@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

dm space map common: add bounds check to sm_ll_lookup_bitmap()

[ Upstream commit cba23ac158db7f3cd48a923d6861bee2eb7a2978 ]

Corrupted metadata could warrant returning error from sm_ll_lookup_bitmap().

Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dm btree: add a defensive bounds check to insert_at()

[ Upstream commit 85bca3c05b6cca31625437eedf2060e846c4bbad ]

Corrupt metadata could trigger an out of bounds write.

Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mac80211: allow non-standard VHT MCS-10/11

[ Upstream commit 04be6d337d37400ad5b3d5f27ca87645ee5a18a3 ]

Some AP can possibly try non-standard VHT rate and mac80211 warns and drops
packets, and leads low TCP throughput.

    Rate marked as a VHT rate but data is invalid: MCS: 10, NSS: 2
    WARNING: CPU: 1 PID: 7817 at net/mac80211/rx.c:4856 ieee80211_rx_list+0x223/0x2f0 [mac8021

Since commit c27aa56a72b8 ("cfg80211: add VHT rate entries for MCS-10 and MCS-11")
has added, mac80211 adds this support as well.

After this patch, throughput is good and iw can get the bitrate:
    rx bitrate: 975.1 MBit/s VHT-MCS 10 80MHz short GI VHT-NSS 2
or
    rx bitrate: 1083.3 MBit/s VHT-MCS 11 80MHz short GI VHT-NSS 2

Buglink: https://bugzilla.suse.com/show_bug.cgi?id=1192891
Reported-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20220103013623.17052-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: mdio: Demote probed message to debug print

[ Upstream commit 7590fc6f80ac2cbf23e6b42b668bbeded070850b ]

On systems with large numbers of MDIO bus/muxes the message indicating
that a given MDIO bus has been successfully probed is repeated for as
many buses we have, which can eat up substantial boot time for no
reason, demote to a debug print.

Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220103194024.2620-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

btrfs: remove BUG_ON(!eie) in find_parent_nodes

[ Upstream commit 9f05c09d6baef789726346397438cca4ec43c3ee ]

If we're looking for leafs that point to a data extent we want to record
the extent items that point at our bytenr.  At this point we have the
reference and we know for a fact that this leaf should have a reference
to our bytenr.  However if there's some sort of corruption we may not
find any references to our leaf, and thus could end up with eie == NULL.
Replace this BUG_ON() with an ASSERT() and then return -EUCLEAN for the
mortals.

Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

btrfs: remove BUG_ON() in find_parent_nodes()

[ Upstream commit fcba0120edf88328524a4878d1d6f4ad39f2ec81 ]

We search for an extent entry with .offset = -1, which shouldn't be a
thing, but corruption happens.  Add an ASSERT() for the developers,
return -EUCLEAN for mortals.

Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ACPI: CPPC: Check present CPUs for determining _CPC is valid

[ Upstream commit 2aeca6bd02776d7f56a49a32be0dd184f204d888 ]

As this is a static check, it should be based upon what is currently
present on the system. This makes probeing more deterministic.

While local APIC flags field (lapic_flags) of cpu core in MADT table is
0, then the cpu core won't be enabled. In this case, _CPC won't be found
in this core, and return back to _CPC invalid with walking through
possible cpus (include disable cpus). This is not expected, so switch to
check present CPUs instead.

Reported-by: Jinzhou Su <Jinzhou.Su@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ACPI: battery: Add the ThinkPad "Not Charging" quirk

[ Upstream commit e96c1197aca628f7d2480a1cc3214912b40b3414 ]

The EC/ACPI firmware on Lenovo ThinkPads used to report a status
of "Unknown" when the battery is between the charge start and
charge stop thresholds. On Windows, it reports "Not Charging"
so the quirk has been added to also report correctly.

Now the "status" attribute returns "Not Charging" when the
battery on ThinkPads is not physicaly charging.

Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

amdgpu/pm: Make sysfs pm attributes as read-only for VFs

[ Upstream commit 11c9cc95f818f0f187e9b579a7f136f532b42445 ]

== Description ==
Setting values of pm attributes through sysfs
should not be allowed in SRIOV mode.
These calls will not be processed by FW anyway,
but error handling on sysfs level should be improved.

== Changes ==
This patch prohibits performing of all set commands
in SRIOV mode on sysfs level.
It offers better error handling as calls that are
not allowed will not be propagated further.

== Test ==
Writing to any sysfs file in passthrough mode will succeed.
Writing to any sysfs file in ONEVF mode will yield error:
"calling process does not have sufficient permission to execute a command".

Signed-off-by: Marina Nikolic <Marina.Nikolic@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu: fixup bad vram size on gmc v8

[ Upstream commit 11544d77e3974924c5a9c8a8320b996a3e9b2f8b ]

Some boards(like RX550) seem to have garbage in the upper
16 bits of the vram size register.  Check for
this and clamp the size properly.  Fixes
boards reporting bogus amounts of vram.

after add this patch,the maximum GPU VRAM size is 64GB,
otherwise only 64GB vram size will be used.

Signed-off-by: Zongmin Zhou<zhouzongmin@kylinos.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mmc: mtk-sd: Use readl_poll_timeout instead of open-coded polling

[ Upstream commit ffaea6ebfe9ce06ebb3a54811a47688f2b0893cd ]

Replace all instances of open-coded while loops for polling registers
with calls to readl_poll_timeout() and, while at it, also fix some
possible infinite loop instances.

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20211216125748.179602-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ACPICA: Hardware: Do not flush CPU cache when entering S4 and S5

[ Upstream commit 1d4e0b3abb168b2ee1eca99c527cffa1b80b6161 ]

ACPICA commit 3dd7e1f3996456ef81bfe14cba29860e8d42949e

According to ACPI 6.4, Section 16.2, the CPU cache flushing is
required on entering to S1, S2, and S3, but the ACPICA code
flushes the CPU cache regardless of the sleep state.

Blind cache flush on entering S5 causes problems for TDX.

Flushing happens with WBINVD that is not supported in the TDX
environment.

TDX only supports S5 and adjusting ACPICA code to conform to the
spec more strictly fixes the issue.

Link: https://github.com/acpica/acpica/commit/3dd7e1f3
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ACPICA: Fix wrong interpretation of PCC address

[ Upstream commit 9a3b8655db1ada31c82189ae13f40eb25da48c35 ]

ACPICA commit 41be6afacfdaec2dba3a5ed368736babc2a7aa5c

With the PCC Opregion in the firmware and we are hitting below kernel crash:

-->8
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
 Workqueue: pm pm_runtime_work
 pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
 pc : __memcpy+0x54/0x260
 lr : acpi_ex_write_data_to_field+0xb8/0x194
 Call trace:
  __memcpy+0x54/0x260
  acpi_ex_store_object_to_node+0xa4/0x1d4
  acpi_ex_store+0x44/0x164
  acpi_ex_opcode_1A_1T_1R+0x25c/0x508
  acpi_ds_exec_end_op+0x1b4/0x44c
  acpi_ps_parse_loop+0x3a8/0x614
  acpi_ps_parse_aml+0x90/0x2f4
  acpi_ps_execute_method+0x11c/0x19c
  acpi_ns_evaluate+0x1ec/0x2b0
  acpi_evaluate_object+0x170/0x2b0
  acpi_device_set_power+0x118/0x310
  acpi_dev_suspend+0xd4/0x180
  acpi_subsys_runtime_suspend+0x28/0x38
  __rpm_callback+0x74/0x328
  rpm_suspend+0x2d8/0x624
  pm_runtime_work+0xa4/0xb8
  process_one_work+0x194/0x25c
  worker_thread+0x260/0x49c
  kthread+0x14c/0x30c
  ret_from_fork+0x10/0x20
 Code: f9000006 f81f80a7 d65f03c0 361000c2 (b9400026)
 ---[ end trace 24d8a032fa77b68a ]---

The reason for the crash is that the PCC channel index passed via region.address
in acpi_ex_store_object_to_node is interpreted as the channel subtype
incorrectly.

Assuming the PCC op_region support is not used by any other type, let us
remove the subtype check as the AML has no access to the subtype information.
Once we remove it, the kernel crash disappears and correctly complains about
missing PCC Opregion handler.

ACPI Error: No handler for Region [PFRM] ((____ptrval____)) [PCC] (20210730/evregion-130)
ACPI Error: Region PCC (ID=10) has no handler (20210730/exfldio-261)
ACPI Error: Aborting method \_SB.ETH0._PS3 due to previous error (AE_NOT_EXIST) (20210730/psparse-531)

Link: https://github.com/acpica/acpica/commit/41be6afa
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ACPICA: Executer: Fix the REFCLASS_REFOF case in acpi_ex_opcode_1A_0T_1R()

[ Upstream commit 24ea5f90ec9548044a6209685c5010edd66ffe8f ]

ACPICA commit d984f12041392fa4156b52e2f7e5c5e7bc38ad9e

If Operand[0] is a reference of the ACPI_REFCLASS_REFOF class,
acpi_ex_opcode_1A_0T_1R () calls acpi_ns_get_attached_object () to
obtain return_desc which may require additional resolution with
the help of acpi_ex_read_data_from_field (). If the latter fails,
the reference counter of the original return_desc is decremented
which is incorrect, because acpi_ns_get_attached_object () does not
increment the reference counter of the object returned by it.

This issue may lead to premature deletion of the attached object
while it is still attached and a use-after-free and crash in the
host OS.  For example, this may happen when on evaluation of ref_of()
a local region field where there is no registered handler for the
given Operation Region.

Fix it by making acpi_ex_opcode_1A_0T_1R () return Status right away
after a acpi_ex_read_data_from_field () failure.

Link: https://github.com/acpica/acpica/commit/d984f120
Link: https://github.com/acpica/acpica/pull/685
Reported-by: Lenny Szubowicz <lszubowi@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ACPICA: Utilities: Avoid deleting the same object twice in a row

[ Upstream commit 1cdfe9e346b4c5509ffe19ccde880fd259d9f7a3 ]

ACPICA commit c11af67d8f7e3d381068ce7771322f2b5324d687

If original_count is 0 in acpi_ut_update_ref_count (),
acpi_ut_delete_internal_obj () is invoked for the target object, which is
incorrect, because that object has been deleted once already and the
memory allocated to store it may have been reclaimed and allocated
for a different purpose by the host OS.  Moreover, a confusing debug
message following the "Reference Count is already zero, cannot
decrement" warning is printed in that case.

To fix this issue, make acpi_ut_update_ref_count () return after finding
that original_count is 0 and printing the above warning.

Link: https://github.com/acpica/acpica/commit/c11af67d
Link: https://github.com/acpica/acpica/pull/652
Reported-by: Mark Asselstine <mark.asselstine@windriver.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ACPICA: actypes.h: Expand the ACPI_ACCESS_ definitions

[ Upstream commit f81bdeaf816142e0729eea0cc84c395ec9673151 ]

ACPICA commit bc02c76d518135531483dfc276ed28b7ee632ce1

The current ACPI_ACCESS_*_WIDTH defines do not provide a way to
test that size is small enough to not cause an overflow when
applied to a 32-bit integer.

Rather than adding more magic numbers, add ACPI_ACCESS_*_SHIFT,
ACPI_ACCESS_*_MAX, and ACPI_ACCESS_*_DEFAULT #defines and
redefine ACPI_ACCESS_*_WIDTH in terms of the new #defines.

This was inititally reported on Linux where a size of 102 in
ACPI_ACCESS_BIT_WIDTH caused an overflow error in the SPCR
initialization code.

Link: https://github.com/acpica/acpica/commit/bc02c76d
Signed-off-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

jffs2: GC deadlock reading a page that is used in jffs2_write_begin()

[ Upstream commit aa39cc675799bc92da153af9a13d6f969c348e82 ]

GC task can deadlock in read_cache_page() because it may attempt
to release a page that is actually allocated by another task in
jffs2_write_begin().
The reason is that in jffs2_write_begin() there is a small window
a cache page is allocated for use but not set Uptodate yet.

This ends up with a deadlock between two tasks:
1) A task (e.g. file copy)
   - jffs2_write_begin() locks a cache page
   - jffs2_write_end() tries to lock "alloc_sem" from
 jffs2_reserve_space() <-- STUCK
2) GC task (jffs2_gcd_mtd3)
   - jffs2_garbage_collect_pass() locks "alloc_sem"
   - try to lock the same cache page in read_cache_page() <-- STUCK

So to avoid this deadlock, hold "alloc_sem" in jffs2_write_begin()
while reading data in a cache page.

Signed-off-by: Kyeong Yoo <kyeong.yoo@alliedtelesis.co.nz>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/etnaviv: consider completed fence seqno in hang check

[ Upstream commit cdd156955f946beaa5f3a00d8ccf90e5a197becc ]

Some GPU heavy test programs manage to trigger the hangcheck quite often.
If there are no other GPU users in the system and the test program
exhibits a very regular structure in the commandstreams that are being
submitted, we can end up with two distinct submits managing to trigger
the hangcheck with the FE in a very similar address range. This leads
the hangcheck to believe that the GPU is stuck, while in reality the GPU
is already busy working on a different job. To avoid those spurious
GPU resets, also remember and consider the last completed fence seqno
in the hang check.

Reported-by: Joerg Albert <joerg.albert@iav.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

xfrm: rate limit SA mapping change message to user space

[ Upstream commit 4e484b3e969b52effd95c17f7a86f39208b2ccf4 ]

Kernel generates mapping change message, XFRM_MSG_MAPPING,
when a source port chage is detected on a input state with UDP
encapsulation set.  Kernel generates a message for each IPsec packet
with new source port.  For a high speed flow per packet mapping change
message can be excessive, and can overload the user space listener.

Introduce rate limiting for XFRM_MSG_MAPPING message to the user space.

The rate limiting is configurable via netlink, when adding a new SA or
updating it. Use the new attribute XFRMA_MTIMER_THRESH in seconds.

v1->v2 change:
update xfrm_sa_len()

v2->v3 changes:
use u32 insted unsigned long to reduce size of struct xfrm_state
fix xfrm_ompat size Reported-by: kernel test robot <lkp@intel.com>
accept XFRM_MSG_MAPPING only when XFRMA_ENCAP is present

Co-developed-by: Thomas Egerer <thomas.egerer@secunet.com>
Signed-off-by: Thomas Egerer <thomas.egerer@secunet.com>
Signed-off-by: Antony Antony <antony.antony@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: vhci: Set HCI_QUIRK_VALID_LE_STATES

[ Upstream commit cfb4c313be670fd4bd09650216620fa4514cdb93 ]

This set HCI_QUIRK_VALID_LE_STATES quirk which is required for the likes
of experimental LE simultaneous roles.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: btintel: Add missing quirks and msft ext for legacy bootloader

[ Upstream commit 3547a008c8962df2175db1e78b80f27e027ec549 ]

This patch add missing HCI quirks and MSFT extension for legacy
bootloader when it is running in the operational firmware.

Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ath11k: Fix napi related hang

[ Upstream commit d943fdad7589653065be0e20aadc6dff37725ed4 ]

Similar to the same bug in ath10k, a napi disable w/out it being enabled
will hang forever.  I believe I saw this while trying rmmod after driver
had some failure on startup.  Fix it by keeping state on whether napi is
enabled or not.

And, remove un-used napi pointer in ath11k driver base struct.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20200903195254.29379-1-greearb@candelatech.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

um: registers: Rename function names to avoid conflicts and build problems

[ Upstream commit 077b7320942b64b0da182aefd83c374462a65535 ]

The function names init_registers() and restore_registers() are used
in several net/ethernet/ and gpu/drm/ drivers for other purposes (not
calls to UML functions), so rename them.

This fixes multiple build errors.

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: linux-um@lists.infradead.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>

block: check minor range in device_add_disk()

[ Upstream commit e338924bd05d6e71574bc13e310c89e10e49a8a5 ]

ioctl(fd, LOOP_CTL_ADD, 1048576) causes

  sysfs: cannot create duplicate filename '/dev/block/7:0'

message because such request is treated as if ioctl(fd, LOOP_CTL_ADD, 0)
due to MINORMASK == 1048575. Verify that all minor numbers for that device
fit in the minor range.

Reported-by: wangyangbo <wangyangbo@uniontech.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/b1b19379-23ee-5379-0eb5-94bf5f79f1b4@i-love.sakura.ne.jp
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mmc: sdhci-pci-gli: GL9755: Support for CD/WP inversion on OF platforms

[ Upstream commit 189f1d9bc3a5ea3e442e119e4a5deda63da8c462 ]

This is required on some Apple ARM64 laptops using this controller.
As is typical on DT platforms, pull these quirks from the device tree
using the standard mmc bindings.

See Documentation/devicetree/bindings/mmc/mmc-controller.yaml

Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20211215161045.38843-2-marcan@marcan.st
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: pcie: make sure prph_info is set when treating wakeup IRQ

[ Upstream commit 459fc0f2c6b0f6e280bfa0f230c100c9dfe3a199 ]

In some rare cases when the HW is in a bad state, we may get this
interrupt when prph_info is not set yet.  Then we will try to
dereference it to check the sleep_notif element, which will cause an
oops.

Fix that by ignoring the interrupt if prph_info is not set yet.

Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211219132536.0537aa562313.I183bb336345b9b3da196ba9e596a6f189fbcbd09@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: mvm: fix AUX ROC removal

[ Upstream commit f0337cb48f3bf5f0bbccc985d8a0a8c4aa4934b7 ]

When IWL_UCODE_TLV_CAPA_SESSION_PROT_CMD is set, removing a time event
always tries to cancel session protection. However, AUX ROC does
not use session protection so it was never removed. As a result,
if the driver tries to allocate another AUX ROC event right after
cancelling the first one, it will fail with a warning.
In addition, the time event data passed to iwl_mvm_remove_aux_roc_te()
is incorrect. Fix it.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211219132536.915e1f69f062.Id837e917f1c2beaca7c1eb33333d622548918a76@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: mvm: Fix calculation of frame length

[ Upstream commit 40a0b38d7a7f91a6027287e0df54f5f547e8d27e ]

The RADA might include in the Rx frame the MIC and CRC bytes.
These bytes should be removed for non monitor interfaces and
should not be passed to mac80211.

Fix the Rx processing to remove the extra bytes on non monitor
cases.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211219121514.098be12c801e.I1d81733d8a75b84c3b20eb6e0d14ab3405ca6a86@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: remove module loading failure message

[ Upstream commit 6518f83ffa51131daaf439b66094f684da3fb0ae ]

When CONFIG_DEBUG_TEST_DRIVER_REMOVE is set, iwlwifi crashes
when the opmode module cannot be loaded, due to completing
the completion before using drv->dev, which can then already
be freed.

Fix this by removing the (fairly useless) message. Moving the
completion later causes a deadlock instead, so that's not an
option.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20211210091245.289008-2-luca@coelho.fi
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: fix leaks/bad data after failed firmware load

[ Upstream commit ab07506b0454bea606095951e19e72c282bfbb42 ]

If firmware load fails after having loaded some parts of the
firmware, e.g. the IML image, then this would leak. For the
host command list we'd end up running into a WARN on the next
attempt to load another firmware image.

Fix this by calling iwl_dealloc_ucode() on failures, and make
that also clear the data so we start fresh on the next round.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211210110539.1f742f0eb58a.I1315f22f6aa632d94ae2069f85e1bca5e734dce0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PM: AVS: qcom-cpr: Use div64_ul instead of do_div

[ Upstream commit 92c550f9ffd2884bb5def52b5c0485a35e452784 ]

do_div() does a 64-by-32 division. Here the divisor is an unsigned long
which on some platforms is 64 bit wide. So use div64_ul instead of do_div
to avoid a possible truncation.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211125014311.45942-1-deng.changcheng@zte.com.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtw88: 8822c: update rx settings to prevent potential hw deadlock

[ Upstream commit c1afb26727d9e507d3e17a9890e7aaf7fc85cd55 ]

These settings enables mac to detect and recover when rx fifo
circuit deadlock occurs. Previous version missed this, so we fix it.

Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211217012708.8623-1-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

ath9k: Fix out-of-bound memcpy in ath9k_hif_usb_rx_stream

[ Upstream commit 6ce708f54cc8d73beca213cec66ede5ce100a781 ]

Large pkt_len can lead to out-out-bound memcpy. Current
ath9k_hif_usb_rx_stream allows combining the content of two urb
inputs to one pkt. The first input can indicate the size of the
pkt. Any remaining size is saved in hif_dev->rx_remain_len.
While processing the next input, memcpy is used with rx_remain_len.

4-byte pkt_len can go up to 0xffff, while a single input is 0x4000
maximum in size (MAX_RX_BUF_SIZE). Thus, the patch adds a check for
pkt_len which must not exceed 2 * MAX_RX_BUG_SIZE.

BUG: KASAN: slab-out-of-bounds in ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
Read of size 46393 at addr ffff888018798000 by task kworker/0:1/23

CPU: 0 PID: 23 Comm: kworker/0:1 Not tainted 5.6.0 #63
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS rel-1.10.2-0-g5f4c7b1-prebuilt.qemu-project.org 04/01/2014
Workqueue: events request_firmware_work_func
Call Trace:
 <IRQ>
 dump_stack+0x76/0xa0
 print_address_description.constprop.0+0x16/0x200
 ? ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
 ? ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
 __kasan_report.cold+0x37/0x7c
 ? ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
 kasan_report+0xe/0x20
 check_memory_region+0x15a/0x1d0
 memcpy+0x20/0x50
 ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
 ? hif_usb_mgmt_cb+0x2d9/0x2d9 [ath9k_htc]
 ? _raw_spin_lock_irqsave+0x7b/0xd0
 ? _raw_spin_trylock_bh+0x120/0x120
 ? __usb_unanchor_urb+0x12f/0x210
 __usb_hcd_giveback_urb+0x1e4/0x380
 usb_giveback_urb_bh+0x241/0x4f0
 ? __hrtimer_run_queues+0x316/0x740
 ? __usb_hcd_giveback_urb+0x380/0x380
 tasklet_action_common.isra.0+0x135/0x330
 __do_softirq+0x18c/0x634
 irq_exit+0x114/0x140
 smp_apic_timer_interrupt+0xde/0x380
 apic_timer_interrupt+0xf/0x20

I found the bug using a custome USBFuzz port. It's a research work
to fuzz USB stack/drivers. I modified it to fuzz ath9k driver only,
providing hand-crafted usb descriptors to QEMU.

After fixing the value of pkt_tag to ATH_USB_RX_STREAM_MODE_TAG in QEMU
emulation, I found the KASAN report. The bug is triggerable whenever
pkt_len is above two MAX_RX_BUG_SIZE. I used the same input that crashes
to test the driver works when applying the patch.

Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/YXsidrRuK6zBJicZ@10-18-43-117.dynapool.wireless.nyu.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>

ath9k_htc: fix NULL pointer dereference at ath9k_htc_tx_get_packet()

[ Upstream commit 8b3046abc99eefe11438090bcc4ec3a3994b55d0 ]

syzbot is reporting lockdep warning at ath9k_wmi_event_tasklet() followed
by kernel panic at get_htc_epid_queue() from ath9k_htc_tx_get_packet() from
ath9k_htc_txstatus() [1], for ath9k_wmi_event_tasklet(WMI_TXSTATUS_EVENTID)
depends on spin_lock_init() from ath9k_init_priv() being already completed.

Since ath9k_wmi_event_tasklet() is set by ath9k_init_wmi() from
ath9k_htc_probe_device(), it is possible that ath9k_wmi_event_tasklet() is
called via tasklet interrupt before spin_lock_init() from ath9k_init_priv()
 from ath9k_init_device() from ath9k_htc_probe_device() is called.

Let's hold ath9k_wmi_event_tasklet(WMI_TXSTATUS_EVENTID) no-op until
ath9k_tx_init() completes.

Link: https://syzkaller.appspot.com/bug?extid=31d54c60c5b254d6f75b
Reported-by: syzbot <syzbot+31d54c60c5b254d6f75b@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: syzbot <syzbot+31d54c60c5b254d6f75b@syzkaller.appspotmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/77b76ac8-2bee-6444-d26c-8c30858b8daa@i-love.sakura.ne.jp
Signed-off-by: Sasha Levin <sashal@kernel.org>

ath9k_htc: fix NULL pointer dereference at ath9k_htc_rxep()

[ Upstream commit b0ec7e55fce65f125bd1d7f02e2dc4de62abee34 ]

syzbot is reporting lockdep warning followed by kernel panic at
ath9k_htc_rxep() [1], for ath9k_htc_rxep() depends on ath9k_rx_init()
being already completed.

Since ath9k_htc_rxep() is set by ath9k_htc_connect_svc(WMI_BEACON_SVC)
 from ath9k_init_htc_services(), it is possible that ath9k_htc_rxep() is
called via timer interrupt before ath9k_rx_init() from ath9k_init_device()
is called.

Since we can't call ath9k_init_device() before ath9k_init_htc_services(),
let's hold ath9k_htc_rxep() no-op until ath9k_rx_init() completes.

Link: https://syzkaller.appspot.com/bug?extid=4d2d56175b934b9a7bf9
Reported-by: syzbot <syzbot+4d2d56175b934b9a7bf9@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: syzbot <syzbot+4d2d56175b934b9a7bf9@syzkaller.appspotmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/2b88f416-b2cb-7a18-d688-951e6dc3fe92@i-love.sakura.ne.jp
Signed-off-by: Sasha Levin <sashal@kernel.org>

mt76: mt7615: improve wmm index allocation

[ Upstream commit 70fb028707c8871ef9e56b3ffa3d895e14956cc4 ]

Typically all AP interfaces on a PHY will share the same WMM settings, while
sta/mesh interfaces will usually inherit the settings from a remote device.
In order minimize the likelihood of conflicting WMM settings, make all AP
interfaces share one slot, and all non-AP interfaces another one.

This also fixes running multiple AP interfaces on MT7613, which only has 3
WMM slots.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mt76: do not pass the received frame with decryption error

[ Upstream commit dd28dea52ad9376d2b243a8981726646e1f60b1a ]

MAC80211 doesn't care any decryption error in 802.3 path, so received
frame will be dropped if HW tell us that the cipher configuration is not
matched as well as the header has been translated to 802.3. This case only
appears when IEEE80211_FCTL_PROTECTED is 0 and cipher suit is not none in
the corresponding HW entry.

The received frame is only reported to monitor interface if HW decryption
block tell us there is ICV error or CCMP/BIP/WPI MIC error. Note in this
case the reported frame is decrypted 802.11 frame and the payload may be
malformed due to mismatched key.

Signed-off-by: Xing Song <xing.song@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mt76: mt7615: fix possible deadlock while mt7615_register_ext_phy()

[ Upstream commit 8c55516de3f9b76b9d9444e7890682ec2efc809f ]

ieee80211_register_hw() is called with rtnl_lock held, and this could be
caused lockdep from a work item that's on a workqueue that is flushed
with the rtnl held.

Move mt7615_register_ext_phy() outside the init_work().

Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: hub: Add delay for SuperSpeed hub resume to let links transit to U0

[ Upstream commit 00558586382891540c59c9febc671062425a6e47 ]

When a new USB device gets plugged to nested hubs, the affected hub,
which connects to usb 2-1.4-port2, doesn't report there's any change,
hence the nested hubs go back to runtime suspend like nothing happened:
[  281.032951] usb usb2: usb wakeup-resume
[  281.032959] usb usb2: usb auto-resume
[  281.032974] hub 2-0:1.0: hub_resume
[  281.033011] usb usb2-port1: status 0263 change 0000
[  281.033077] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[  281.049797] usb 2-1: usb wakeup-resume
[  281.069800] usb 2-1: Waited 0ms for CONNECT
[  281.069810] usb 2-1: finish resume
[  281.070026] hub 2-1:1.0: hub_resume
[  281.070250] usb 2-1-port4: status 0203 change 0000
[  281.070272] usb usb2-port1: resume, status 0
[  281.070282] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[  281.089813] usb 2-1.4: usb wakeup-resume
[  281.109792] usb 2-1.4: Waited 0ms for CONNECT
[  281.109801] usb 2-1.4: finish resume
[  281.109991] hub 2-1.4:1.0: hub_resume
[  281.110147] usb 2-1.4-port2: status 0263 change 0000
[  281.110234] usb 2-1-port4: resume, status 0
[  281.110239] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[  281.110266] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[  281.110426] hub 2-1.4:1.0: hub_suspend
[  281.110565] usb 2-1.4: usb auto-suspend, wakeup 1
[  281.130998] hub 2-1:1.0: hub_suspend
[  281.137788] usb 2-1: usb auto-suspend, wakeup 1
[  281.142935] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[  281.177828] usb 2-1: usb wakeup-resume
[  281.197839] usb 2-1: Waited 0ms for CONNECT
[  281.197850] usb 2-1: finish resume
[  281.197984] hub 2-1:1.0: hub_resume
[  281.198203] usb 2-1-port4: status 0203 change 0000
[  281.198228] usb usb2-port1: resume, status 0
[  281.198237] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[  281.217835] usb 2-1.4: usb wakeup-resume
[  281.237834] usb 2-1.4: Waited 0ms for CONNECT
[  281.237845] usb 2-1.4: finish resume
[  281.237990] hub 2-1.4:1.0: hub_resume
[  281.238067] usb 2-1.4-port2: status 0263 change 0000
[  281.238148] usb 2-1-port4: resume, status 0
[  281.238152] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[  281.238166] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[  281.238385] hub 2-1.4:1.0: hub_suspend
[  281.238523] usb 2-1.4: usb auto-suspend, wakeup 1
[  281.258076] hub 2-1:1.0: hub_suspend
[  281.265744] usb 2-1: usb auto-suspend, wakeup 1
[  281.285976] hub 2-0:1.0: hub_suspend
[  281.285988] usb usb2: bus auto-suspend, wakeup 1

USB 3.2 spec, 9.2.5.4 "Changing Function Suspend State" says that "If
the link is in a non-U0 state, then the device must transition the link
to U0 prior to sending the remote wake message", but the hub only
transits the link to U0 after signaling remote wakeup.

So be more forgiving and use a 20ms delay to let the link transit to U0
for remote wakeup.

Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20211215120108.336597-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

cpufreq: Fix initialization of min and max frequency QoS requests

[ Upstream commit 521223d8b3ec078f670c7c35a1a04b1b2af07966 ]

The min and max frequency QoS requests in the cpufreq core are
initialized to whatever the current min and max frequency values are
at the init time, but if any of these values change later (for
example, cpuinfo.max_freq is updated by the driver), these initial
request values will be limiting the CPU frequency unnecessarily
unless they are changed by user space via sysfs.

To address this, initialize min_freq_req and max_freq_req to
FREQ_QOS_MIN_DEFAULT_VALUE and FREQ_QOS_MAX_DEFAULT_VALUE,
respectively, so they don't really limit anything until user
space updates them.

Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PM: runtime: Add safety net to supplier device release

[ Upstream commit d1579e61192e0e686faa4208500ef4c3b529b16c ]

Because refcount_dec_not_one() returns true if the target refcount
becomes saturated, it is generally unsafe to use its return value as
a loop termination condition, but that is what happens when a device
link's supplier device is released during runtime PM suspend
operations and on device link removal.

To address this, introduce pm_runtime_release_supplier() to be used
in the above cases which will check the supplier device's runtime
PM usage counter in addition to the refcount_dec_not_one() return
value, so the loop can be terminated in case the rpm_active refcount
value becomes invalid, and update the code in question to use it as
appropriate.

This change is not expected to have any visible functional impact.

Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

crypto: hisilicon/hpre - fix memory leak in hpre_curve25519_src_init()

[ Upstream commit 51fa916b81e5f406a74f14a31a3a228c3cc060ad ]

hpre_curve25519_src_init() allocates memory for 'ptr' before calling
memcmp(). If memcmp() returns 0, the function will return '-EINVAL'
without freeing memory.

Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

crypto: ccp - Move SEV_INIT retry for corrupted data

[ Upstream commit e423b9d75e779d921e6adf5ac3d0b59400d6ba7e ]

Move the data corrupted retry of SEV_INIT into the
__sev_platform_init_locked() function. This is for upcoming INIT_EX
support as well as helping direct callers of
__sev_platform_init_locked() which currently do not support the
retry.

Signed-off-by: Peter Gonda <pgonda@google.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Marc Orr <marcorr@google.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Rientjes <rientjes@google.com>
Cc: John Allen <john.allen@amd.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: tegra: Adjust length of CCPLEX cluster MMIO region

[ Upstream commit 2b14cbd643feea5fc17c6e8bead4e71088c69acd ]

The Tegra186 CCPLEX cluster register region is 4 MiB is length, not 4
MiB - 1. This was likely presumed to be the "limit" rather than length.
Fix it up.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: ls1028a-qds: move rtc node to the correct i2c bus

[ Upstream commit cbe9d948eadfe352ad45495a7cc5bf20a1b29d90 ]

The i2c rtc is on i2c2 bus not i2c1 bus, so fix it in dts.

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Li Yang <leoyang.lil@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

audit: ensure userspace is penalized the same as the kernel when under pressure

[ Upstream commit 8f110f530635af44fff1f4ee100ecef0bac62510 ]

Due to the audit control mutex necessary for serializing audit
userspace messages we haven't been able to block/penalize userspace
processes that attempt to send audit records while the system is
under audit pressure.  The result is that privileged userspace
applications have a priority boost with respect to audit as they are
not bound by the same audit queue throttling as the other tasks on
the system.

This patch attempts to restore some balance to the system when under
audit pressure by blocking these privileged userspace tasks after
they have finished their audit processing, and dropped the audit
control mutex, but before they return to userspace.

Reported-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Tested-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/amdgpu: fix gmc bo pin count leak in SRIOV

[ Upstream commit 948e7ce01413b71395723aaf846015062aea3a43 ]

[Why]
gmc bo will be pinned during loading amdgpu and reset in SRIOV while
only unpinned in unload amdgpu

[How]
add amdgpu_in_reset and sriov judgement to skip pin bo

v2: fix wrong judgement

Signed-off-by: Jingwen Chen <Jingwen.Chen2@amd.com>
Reviewed-by: Horace Chen <horace.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>