Madalin Bucur [Mon, 19 Dec 2016 20:42:43 +0000 (22:42 +0200)]
fsl/fman: fix 1G support for QSGMII interfaces
QSGMII ports were not advertising 1G speed.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 20 Dec 2016 18:50:51 +0000 (13:50 -0500)]
Merge branch 'phy-broken-modes'
Jerome Brunet says:
====================
phy: Fix integration of eee-broken-modes
The purpose of this series is to fix the integration of the ethernet phy
property "eee-broken-modes" [0]
The v3 of this series has been merged, missing a fix (error reported by
kbuild robot) available in the v4 [1]
More importantly, Florian opposed adding a DT property mapping a device
register this directly [2]. The concern was that the property could be
abused to implement platform configuration policy. After discussing it,
I think we agreed that such information about the HW (defect) should appear
in the platform DT. However, the preferred way is to add a boolean property
for each EEE broken mode.
[0]: http://lkml.kernel.org/r/
1480326409-25419-1-git-send-email-jbrunet@baylibre.com
[1]: http://lkml.kernel.org/r/
1480348229-25672-1-git-send-email-jbrunet@baylibre.com
[2]: http://lkml.kernel.org/r/
e14a3b0c-dc34-be14-48b3-
518a0ad0c080@gmail.com
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
jbrunet [Mon, 19 Dec 2016 15:05:38 +0000 (16:05 +0100)]
dt: bindings: net: use boolean dt properties for eee broken modes
The patches regarding eee-broken-modes was merged before all people
involved could find an agreement on the best way to move forward.
While we agreed on having a DT property to mark particular modes as broken,
the value used for eee-broken-modes mapped the phy register in very direct
way. Because of this, the concern is that it could be used to implement
configuration policies instead of describing a broken HW.
In the end, having a boolean property for each mode seems to be preferred
over one bit field value mapping the register (too) directly.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
jbrunet [Mon, 19 Dec 2016 15:05:37 +0000 (16:05 +0100)]
net: phy: use boolean dt properties for eee broken modes
The patches regarding eee-broken-modes was merged before all people
involved could find an agreement on the best way to move forward.
While we agreed on having a DT property to mark particular modes as broken,
the value used for eee-broken-modes mapped the phy register in very direct
way. Because of this, the concern is that it could be used to implement
configuration policies instead of describing a broken HW.
In the end, having a boolean property for each mode seems to be preferred
over one bit field value mapping the register (too) directly.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
jbrunet [Mon, 19 Dec 2016 15:05:36 +0000 (16:05 +0100)]
net: phy: fix sign type error in genphy_config_eee_advert
In genphy_config_eee_advert, the return value of phy_read_mmd_indirect is
checked to know if the register could be accessed but the result is
assigned to a 'u32'.
Changing to 'int' to correctly get errors from phy_read_mmd_indirect.
Fixes: d853d145ea3e ("net: phy: add an option to disable EEE advertisement")
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
zheng li [Mon, 12 Dec 2016 01:56:05 +0000 (09:56 +0800)]
ipv4: Should use consistent conditional judgement for ip fragment in __ip_append_data and ip_finish_output
There is an inconsistent conditional judgement in __ip_append_data and
ip_finish_output functions, the variable length in __ip_append_data just
include the length of application's payload and udp header, don't include
the length of ip header, but in ip_finish_output use
(skb->len > ip_skb_dst_mtu(skb)) as judgement, and skb->len include the
length of ip header.
That causes some particular application's udp payload whose length is
between (MTU - IP Header) and MTU were fragmented by ip_fragment even
though the rst->dev support UFO feature.
Add the length of ip header to length in __ip_append_data to keep
consistent conditional judgement as ip_finish_output for ip fragment.
Signed-off-by: Zheng Li <james.z.li@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Machek [Sun, 18 Dec 2016 20:38:12 +0000 (21:38 +0100)]
stmmac: fix memory barriers
Fix up memory barriers in stmmac driver. They are meant to protect
against DMA engine, so smp_ variants are certainly wrong, and dma_
variants are preferable.
Signed-off-by: Pavel Machek <pavel@denx.de>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arvind Yadav [Wed, 14 Dec 2016 19:03:30 +0000 (00:33 +0530)]
net: ethernet: cavium: octeon: octeon_mgmt: Handle return NULL error from devm_ioremap
Here, If devm_ioremap will fail. It will return NULL.
Kernel can run into a NULL-pointer dereference.
This error check will avoid NULL pointer dereference.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 18 Dec 2016 04:17:04 +0000 (20:17 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes and cleanups from David Miller:
1) Revert bogus nla_ok() change, from Alexey Dobriyan.
2) Various bpf validator fixes from Daniel Borkmann.
3) Add some necessary SET_NETDEV_DEV() calls to hsis_femac and hip04
drivers, from Dongpo Li.
4) Several ethtool ksettings conversions from Philippe Reynes.
5) Fix bugs in inet port management wrt. soreuseport, from Tom Herbert.
6) XDP support for virtio_net, from John Fastabend.
7) Fix NAT handling within a vrf, from David Ahern.
8) Endianness fixes in dpaa_eth driver, from Claudiu Manoil
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (63 commits)
net: mv643xx_eth: fix build failure
isdn: Constify some function parameters
mlxsw: spectrum: Mark split ports as such
cgroup: Fix CGROUP_BPF config
qed: fix old-style function definition
net: ipv6: check route protocol when deleting routes
r6040: move spinlock in r6040_close as SOFTIRQ-unsafe lock order detected
irda: w83977af_ir: cleanup an indent issue
net: sfc: use new api ethtool_{get|set}_link_ksettings
net: davicom: dm9000: use new api ethtool_{get|set}_link_ksettings
net: cirrus: ep93xx: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb3: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb2: use new api ethtool_{get|set}_link_ksettings
bpf: fix mark_reg_unknown_value for spilled regs on map value marking
bpf: fix overflow in prog accounting
bpf: dynamically allocate digest scratch buffer
gtp: Fix initialization of Flags octet in GTPv1 header
gtp: gtp_check_src_ms_ipv4() always return success
net/x25: use designated initializers
isdn: use designated initializers
...
Linus Torvalds [Sun, 18 Dec 2016 03:16:12 +0000 (19:16 -0800)]
Merge uncontroversial parts of branch 'readlink' of git://git./linux/kernel/git/mszeredi/vfs
Pull partial readlink cleanups from Miklos Szeredi.
This is the uncontroversial part of the readlink cleanup patch-set that
simplifies the default readlink handling.
Miklos and Al are still discussing the rest of the series.
* git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
vfs: make generic_readlink() static
vfs: remove ".readlink = generic_readlink" assignments
vfs: default to generic_readlink()
vfs: replace calling i_op->readlink with vfs_readlink()
proc/self: use generic_readlink
ecryptfs: use vfs_get_link()
bad_inode: add missing i_op initializers
Sudip Mukherjee [Sat, 17 Dec 2016 00:45:05 +0000 (00:45 +0000)]
net: mv643xx_eth: fix build failure
The build of sparc allmodconfig fails with the error:
"of_irq_to_resource" [drivers/net/ethernet/marvell/mv643xx_eth.ko]
undefined!
of_irq_to_resource() is defined when CONFIG_OF_IRQ is defined. And also
CONFIG_OF_IRQ can only be defined if CONFIG_IRQ is defined. So we can
safely use #if defined(CONFIG_OF_IRQ) in the code.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emese Revfy [Fri, 16 Dec 2016 21:40:47 +0000 (13:40 -0800)]
isdn: Constify some function parameters
The coming initify gcc plugin expects const pointer types, and caught
some __printf arguments that weren't const yet. This fixes those.
Signed-off-by: Emese Revfy <re.emese@gmail.com>
[kees: expanded commit message]
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 16 Dec 2016 18:29:03 +0000 (19:29 +0100)]
mlxsw: spectrum: Mark split ports as such
When a port is split we should mark it as such, as otherwise the split
ports aren't renamed correctly (e.g. sw1p3 -> sw1p3s1) and the unsplit
operation fails:
$ devlink port split sw1p3 count 4
$ devlink port unsplit eth0
devlink answers: Invalid argument
[ 598.565307] mlxsw_spectrum 0000:03:00.0 eth0: Port wasn't split
Fixes: 67963a33b4fd ("mlxsw: Make devlink port instances independent of spectrum/switchx2 port instances")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Tamir Winetroub <tamirw@mellanox.com>
Reviewed-by: Elad Raz <eladr@mellanox.com>
Tested-by: Tamir Winetroub <tamirw@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 18 Dec 2016 02:44:00 +0000 (18:44 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull more vfs updates from Al Viro:
"In this pile:
- autofs-namespace series
- dedupe stuff
- more struct path constification"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (40 commits)
ocfs2: implement the VFS clone_range, copy_range, and dedupe_range features
ocfs2: charge quota for reflinked blocks
ocfs2: fix bad pointer cast
ocfs2: always unlock when completing dio writes
ocfs2: don't eat io errors during _dio_end_io_write
ocfs2: budget for extent tree splits when adding refcount flag
ocfs2: prohibit refcounted swapfiles
ocfs2: add newlines to some error messages
ocfs2: convert inode refcount test to a helper
simple_write_end(): don't zero in short copy into uptodate
exofs: don't mess with simple_write_{begin,end}
9p: saner ->write_end() on failing copy into non-uptodate page
fix gfs2_stuffed_write_end() on short copies
fix ceph_write_end()
nfs_write_end(): fix handling of short copies
vfs: refactor clone/dedupe_file_range common functions
fs: try to clone files first in vfs_copy_file_range
vfs: misc struct path constification
namespace.c: constify struct path passed to a bunch of primitives
quota: constify struct path in quota_on
...
Andy Lutomirski [Fri, 16 Dec 2016 16:33:45 +0000 (08:33 -0800)]
cgroup: Fix CGROUP_BPF config
CGROUP_BPF depended on SOCK_CGROUP_DATA which can't be manually
enabled, making it rather challenging to turn CGROUP_BPF on.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 18 Dec 2016 02:41:33 +0000 (21:41 -0500)]
Merge tag 'mac80211-for-davem-2016-12-16' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Three fixes:
* avoid a WARN_ON() when trying to use WEP with AP_VLANs
* ensure enough headroom on mesh forwarding packets
* don't report unknown/invalid rates to userspace
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 16 Dec 2016 08:47:41 +0000 (09:47 +0100)]
qed: fix old-style function definition
The newly added file causes a harmless warning, with "make W=1":
drivers/net/ethernet/qlogic/qed/qed_iscsi.c: In function 'qed_get_iscsi_ops':
drivers/net/ethernet/qlogic/qed/qed_iscsi.c:1268:29: warning: old-style function definition [-Wold-style-definition]
This makes it a proper prototype.
Fixes: fc831825f99e ("qed: Add support for hardware offloaded iSCSI.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mantas M [Fri, 16 Dec 2016 08:30:59 +0000 (10:30 +0200)]
net: ipv6: check route protocol when deleting routes
The protocol field is checked when deleting IPv4 routes, but ignored for
IPv6, which causes problems with routing daemons accidentally deleting
externally set routes (observed by multiple bird6 users).
This can be verified using `ip -6 route del <prefix> proto something`.
Signed-off-by: Mantas Mikulėnas <grawity@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manuel Bessler [Fri, 16 Dec 2016 03:55:00 +0000 (22:55 -0500)]
r6040: move spinlock in r6040_close as SOFTIRQ-unsafe lock order detected
'ifconfig eth0 down' makes r6040_close() trigger:
INFO: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected
Fixed by moving calls to phy_stop(), napi_disable(), netif_stop_queue()
to outside of the module's private spin_lock_irq block.
Found on a Versalogic Tomcat SBC with a Vortex86 SoC
s1660e_5150:~# sudo ifconfig eth0 down
[ 61.306415] ======================================================
[ 61.306415] [ INFO: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected ]
[ 61.306415]
4.9.0-gb898d2d-manuel #1 Not tainted
[ 61.306415] ------------------------------------------------------
[ 61.306415] ifconfig/449 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
[ 61.306415] (&dev->lock){+.+...}, at: [<
c1336276>] phy_stop+0x16/0x80
[ 61.306415] and this task is already holding:
[ 61.306415] (&(&lp->lock)->rlock){+.-...}, at: [<
d0934c84>] r6040_close+0x24/0x230 [r6040]
which would create a new lock dependency:
[ 61.306415] (&(&lp->lock)->rlock){+.-...} -> (&dev->lock){+.+...}
[ 61.306415] but this new dependency connects a SOFTIRQ-irq-safe lock:
[ 61.306415] (&(&lp->lock)->rlock){+.-...}
[ 61.306415] ... which became SOFTIRQ-irq-safe at:
[ 61.306415] [ 61.306415] [<
c1075bc5>] __lock_acquire+0x555/0x1770
[ 61.306415] [ 61.306415] [<
c107717c>] lock_acquire+0x7c/0x150
[ 61.306415] [ 61.306415] [<
c14bb334>] _raw_spin_lock_irqsave+0x24/0x40
[ 61.306415] [ 61.306415] [<
d0934ac0>] r6040_start_xmit+0x30/0x1d0 [r6040]
[ 61.306415] [ 61.306415] [<
c13a7d4d>] dev_hard_start_xmit+0x9d/0x2d0
[ 61.306415] [ 61.306415] [<
c13c8a38>] sch_direct_xmit+0xa8/0x140
[ 61.306415] [ 61.306415] [<
c13a8436>] __dev_queue_xmit+0x416/0x780
[ 61.306415] [ 61.306415] [<
c13a87aa>] dev_queue_xmit+0xa/0x10
[ 61.306415] [ 61.306415] [<
c13b4837>] neigh_resolve_output+0x147/0x220
[ 61.306415] [ 61.306415] [<
c144541b>] ip6_finish_output2+0x2fb/0x910
[ 61.306415] [ 61.306415] [<
c14494e6>] ip6_finish_output+0xa6/0x1a0
[ 61.306415] [ 61.306415] [<
c1449635>] ip6_output+0x55/0x320
[ 61.306415] [ 61.306415] [<
c146f4d2>] mld_sendpack+0x352/0x560
[ 61.306415] [ 61.306415] [<
c146fe55>] mld_ifc_timer_expire+0x155/0x280
[ 61.306415] [ 61.306415] [<
c108b081>] call_timer_fn+0x81/0x270
[ 61.306415] [ 61.306415] [<
c108b331>] expire_timers+0xc1/0x180
[ 61.306415] [ 61.306415] [<
c108b4f7>] run_timer_softirq+0x77/0x150
[ 61.306415] [ 61.306415] [<
c1043d04>] __do_softirq+0xb4/0x3d0
[ 61.306415] [ 61.306415] [<
c101a15c>] do_softirq_own_stack+0x1c/0x30
[ 61.306415] [ 61.306415] [<
c104416e>] irq_exit+0x8e/0xa0
[ 61.306415] [ 61.306415] [<
c1019d31>] do_IRQ+0x51/0x100
[ 61.306415] [ 61.306415] [<
c14bc176>] common_interrupt+0x36/0x40
[ 61.306415] [ 61.306415] [<
c1134928>] set_root+0x68/0xf0
[ 61.306415] [ 61.306415] [<
c1136120>] path_init+0x400/0x640
[ 61.306415] [ 61.306415] [<
c11386bf>] path_lookupat+0xf/0xe0
[ 61.306415] [ 61.306415] [<
c1139ebc>] filename_lookup+0x6c/0x100
[ 61.306415] [ 61.306415] [<
c1139fd5>] user_path_at_empty+0x25/0x30
[ 61.306415] [ 61.306415] [<
c11298c6>] SyS_faccessat+0x86/0x1e0
[ 61.306415] [ 61.306415] [<
c1129a30>] SyS_access+0x10/0x20
[ 61.306415] [ 61.306415] [<
c100179f>] do_int80_syscall_32+0x3f/0x110
[ 61.306415] [ 61.306415] [<
c14bba3f>] restore_all+0x0/0x61
[ 61.306415]
[ 61.306415] to a SOFTIRQ-irq-unsafe lock:
[ 61.306415] (&dev->lock){+.+...}
[ 61.306415] ... which became SOFTIRQ-irq-unsafe at:
[ 61.306415] ...[ 61.306415]
[ 61.306415] [<
c1075c0c>] __lock_acquire+0x59c/0x1770
[ 61.306415] [ 61.306415] [<
c107717c>] lock_acquire+0x7c/0x150
[ 61.306415] [ 61.306415] [<
c14b7add>] mutex_lock_nested+0x2d/0x4a0
[ 61.306415] [ 61.306415] [<
c133747d>] phy_probe+0x4d/0xc0
[ 61.306415] [ 61.306415] [<
c1338afe>] phy_attach_direct+0xbe/0x190
[ 61.306415] [ 61.306415] [<
c1338ca7>] phy_connect_direct+0x17/0x60
[ 61.306415] [ 61.306415] [<
c1338d23>] phy_connect+0x33/0x70
[ 61.306415] [ 61.306415] [<
d09357a0>] r6040_init_one+0x3a0/0x500 [r6040]
[ 61.306415] [ 61.306415] [<
c12a78c7>] pci_device_probe+0x77/0xd0
[ 61.306415] [ 61.306415] [<
c12f5e15>] driver_probe_device+0x145/0x280
[ 61.306415] [ 61.306415] [<
c12f5fd9>] __driver_attach+0x89/0x90
[ 61.306415] [ 61.306415] [<
c12f43ef>] bus_for_each_dev+0x4f/0x80
[ 61.306415] [ 61.306415] [<
c12f5954>] driver_attach+0x14/0x20
[ 61.306415] [ 61.306415] [<
c12f55b7>] bus_add_driver+0x197/0x210
[ 61.306415] [ 61.306415] [<
c12f6a21>] driver_register+0x51/0xd0
[ 61.306415] [ 61.306415] [<
c12a6955>] __pci_register_driver+0x45/0x50
[ 61.306415] [ 61.306415] [<
d0938017>] 0xd0938017
[ 61.306415] [ 61.306415] [<
c100043f>] do_one_initcall+0x2f/0x140
[ 61.306415] [ 61.306415] [<
c10e48c0>] do_init_module+0x4a/0x19b
[ 61.306415] [ 61.306415] [<
c10a680e>] load_module+0x1b2e/0x2070
[ 61.306415] [ 61.306415] [<
c10a6eb9>] SyS_finit_module+0x69/0x80
[ 61.306415] [ 61.306415] [<
c100179f>] do_int80_syscall_32+0x3f/0x110
[ 61.306415] [ 61.306415] [<
c14bba3f>] restore_all+0x0/0x61
[ 61.306415]
[ 61.306415] other info that might help us debug this:
[ 61.306415]
[ 61.306415] Possible interrupt unsafe locking scenario:
[ 61.306415]
[ 61.306415] CPU0 CPU1
[ 61.306415] ---- ----
[ 61.306415] lock(&dev->lock);
[ 61.306415] local_irq_disable();
[ 61.306415] lock(&(&lp->lock)->rlock);
[ 61.306415] lock(&dev->lock);
[ 61.306415] <Interrupt>
[ 61.306415] lock(&(&lp->lock)->rlock);
[ 61.306415]
[ 61.306415] *** DEADLOCK ***
[ 61.306415]
[ 61.306415] 2 locks held by ifconfig/449:
[ 61.306415] #0: (rtnl_mutex){+.+.+.}, at: [<
c13b68ef>] rtnl_lock+0xf/0x20
[ 61.306415] #1: (&(&lp->lock)->rlock){+.-...}, at: [<
d0934c84>] r6040_close+0x24/0x230 [r6040]
[ 61.306415]
[ 61.306415] the dependencies between SOFTIRQ-irq-safe lock and the holding lock:
[ 61.306415] -> (&(&lp->lock)->rlock){+.-...} ops: 3049 {
[ 61.306415] HARDIRQ-ON-W at:
[ 61.306415] [ 61.306415] [<
c1075be7>] __lock_acquire+0x577/0x1770
[ 61.306415] [ 61.306415] [<
c107717c>] lock_acquire+0x7c/0x150
[ 61.306415] [ 61.306415] [<
c14bb21b>] _raw_spin_lock+0x1b/0x30
[ 61.306415] [ 61.306415] [<
d09343cc>] r6040_poll+0x2c/0x330 [r6040]
[ 61.306415] [ 61.306415] [<
c13a5577>] net_rx_action+0x197/0x340
[ 61.306415] [ 61.306415] [<
c1043d04>] __do_softirq+0xb4/0x3d0
[ 61.306415] [ 61.306415] [<
c1044037>] run_ksoftirqd+0x17/0x40
[ 61.306415] [ 61.306415] [<
c105fe91>] smpboot_thread_fn+0x141/0x180
[ 61.306415] [ 61.306415] [<
c105c84e>] kthread+0xde/0x110
[ 61.306415] [ 61.306415] [<
c14bb949>] ret_from_fork+0x19/0x30
[ 61.306415] IN-SOFTIRQ-W at:
[ 61.306415] [ 61.306415] [<
c1075bc5>] __lock_acquire+0x555/0x1770
[ 61.306415] [ 61.306415] [<
c107717c>] lock_acquire+0x7c/0x150
[ 61.306415] [ 61.306415] [<
c14bb334>] _raw_spin_lock_irqsave+0x24/0x40
[ 61.306415] [ 61.306415] [<
d0934ac0>] r6040_start_xmit+0x30/0x1d0 [r6040]
[ 61.306415] [ 61.306415] [<
c13a7d4d>] dev_hard_start_xmit+0x9d/0x2d0
[ 61.306415] [ 61.306415] [<
c13c8a38>] sch_direct_xmit+0xa8/0x140
[ 61.306415] [ 61.306415] [<
c13a8436>] __dev_queue_xmit+0x416/0x780
[ 61.306415] [ 61.306415] [<
c13a87aa>] dev_queue_xmit+0xa/0x10
[ 61.306415] [ 61.306415] [<
c13b4837>] neigh_resolve_output+0x147/0x220
[ 61.306415] [ 61.306415] [<
c144541b>] ip6_finish_output2+0x2fb/0x910
[ 61.306415] [ 61.306415] [<
c14494e6>] ip6_finish_output+0xa6/0x1a0
[ 61.306415] [ 61.306415] [<
c1449635>] ip6_output+0x55/0x320
[ 61.306415] [ 61.306415] [<
c146f4d2>] mld_sendpack+0x352/0x560
[ 61.306415] [ 61.306415] [<
c146fe55>] mld_ifc_timer_expire+0x155/0x280
[ 61.306415] [ 61.306415] [<
c108b081>] call_timer_fn+0x81/0x270
[ 61.306415] [ 61.306415] [<
c108b331>] expire_timers+0xc1/0x180
[ 61.306415] [ 61.306415] [<
c108b4f7>] run_timer_softirq+0x77/0x150
[ 61.306415] [ 61.306415] [<
c1043d04>] __do_softirq+0xb4/0x3d0
[ 61.306415] [ 61.306415] [<
c101a15c>] do_softirq_own_stack+0x1c/0x30
[ 61.306415] [ 61.306415] [<
c104416e>] irq_exit+0x8e/0xa0
[ 61.306415] [ 61.306415] [<
c1019d31>] do_IRQ+0x51/0x100
[ 61.306415] [ 61.306415] [<
c14bc176>] common_interrupt+0x36/0x40
[ 61.306415] [ 61.306415] [<
c1134928>] set_root+0x68/0xf0
[ 61.306415] [ 61.306415] [<
c1136120>] path_init+0x400/0x640
[ 61.306415] [ 61.306415] [<
c11386bf>] path_lookupat+0xf/0xe0
[ 61.306415] [ 61.306415] [<
c1139ebc>] filename_lookup+0x6c/0x100
[ 61.306415] [ 61.306415] [<
c1139fd5>] user_path_at_empty+0x25/0x30
[ 61.306415] [ 61.306415] [<
c11298c6>] SyS_faccessat+0x86/0x1e0
[ 61.306415] [ 61.306415] [<
c1129a30>] SyS_access+0x10/0x20
[ 61.306415] [ 61.306415] [<
c100179f>] do_int80_syscall_32+0x3f/0x110
[ 61.306415] [ 61.306415] [<
c14bba3f>] restore_all+0x0/0x61
[ 61.306415] INITIAL USE at:
[ 61.306415] [ 61.306415] [<
c107586e>] __lock_acquire+0x1fe/0x1770
[ 61.306415] [ 61.306415] [<
c107717c>] lock_acquire+0x7c/0x150
[ 61.306415] [ 61.306415] [<
c14bb334>] _raw_spin_lock_irqsave+0x24/0x40
[ 61.306415] [ 61.306415] [<
d093474e>] r6040_get_stats+0x1e/0x60 [r6040]
[ 61.306415] [ 61.306415] [<
c139fb16>] dev_get_stats+0x96/0xc0
[ 61.306415] [ 61.306415] [<
c14b416e>] rtnl_fill_stats+0x36/0xfd
[ 61.306415] [ 61.306415] [<
c13b7b3c>] rtnl_fill_ifinfo+0x47c/0xce0
[ 61.306415] [ 61.306415] [<
c13bc08e>] rtmsg_ifinfo_build_skb+0x4e/0xd0
[ 61.306415] [ 61.306415] [<
c13bc120>] rtmsg_ifinfo.part.20+0x10/0x40
[ 61.306415] [ 61.306415] [<
c13bc16b>] rtmsg_ifinfo+0x1b/0x20
[ 61.306415] [ 61.306415] [<
c13a9d19>] register_netdevice+0x409/0x550
[ 61.306415] [ 61.306415] [<
c13a9e72>] register_netdev+0x12/0x20
[ 61.306415] [ 61.306415] [<
d09357e8>] r6040_init_one+0x3e8/0x500 [r6040]
[ 61.306415] [ 61.306415] [<
c12a78c7>] pci_device_probe+0x77/0xd0
[ 61.306415] [ 61.306415] [<
c12f5e15>] driver_probe_device+0x145/0x280
[ 61.306415] [ 61.306415] [<
c12f5fd9>] __driver_attach+0x89/0x90
[ 61.306415] [ 61.306415] [<
c12f43ef>] bus_for_each_dev+0x4f/0x80
[ 61.306415] [ 61.306415] [<
c12f5954>] driver_attach+0x14/0x20
[ 61.306415] [ 61.306415] [<
c12f55b7>] bus_add_driver+0x197/0x210
[ 61.306415] [ 61.306415] [<
c12f6a21>] driver_register+0x51/0xd0
[ 61.306415] [ 61.306415] [<
c12a6955>] __pci_register_driver+0x45/0x50
[ 61.306415] [ 61.306415] [<
d0938017>] 0xd0938017
[ 61.306415] [ 61.306415] [<
c100043f>] do_one_initcall+0x2f/0x140
[ 61.306415] [ 61.306415] [<
c10e48c0>] do_init_module+0x4a/0x19b
[ 61.306415] [ 61.306415] [<
c10a680e>] load_module+0x1b2e/0x2070
[ 61.306415] [ 61.306415] [<
c10a6eb9>] SyS_finit_module+0x69/0x80
[ 61.306415] [ 61.306415] [<
c100179f>] do_int80_syscall_32+0x3f/0x110
[ 61.306415] [ 61.306415] [<
c14bba3f>] restore_all+0x0/0x61
[ 61.306415] }
[ 61.306415] ... key at: [<
d0936280>] __key.45893+0x0/0xfffff739 [r6040]
[ 61.306415] ... acquired at:
[ 61.306415] [ 61.306415] [<
c1074a32>] check_irq_usage+0x42/0xb0
[ 61.306415] [ 61.306415] [<
c107677c>] __lock_acquire+0x110c/0x1770
[ 61.306415] [ 61.306415] [<
c107717c>] lock_acquire+0x7c/0x150
[ 61.306415] [ 61.306415] [<
c14b7add>] mutex_lock_nested+0x2d/0x4a0
[ 61.306415] [ 61.306415] [<
c1336276>] phy_stop+0x16/0x80
[ 61.306415] [ 61.306415] [<
d0934ce9>] r6040_close+0x89/0x230 [r6040]
[ 61.306415] [ 61.306415] [<
c13a0a91>] __dev_close_many+0x61/0xa0
[ 61.306415] [ 61.306415] [<
c13a0bbf>] __dev_close+0x1f/0x30
[ 61.306415] [ 61.306415] [<
c13a9127>] __dev_change_flags+0x87/0x150
[ 61.306415] [ 61.306415] [<
c13a9213>] dev_change_flags+0x23/0x60
[ 61.306415] [ 61.306415] [<
c1416238>] devinet_ioctl+0x5f8/0x6f0
[ 61.306415] [ 61.306415] [<
c1417f75>] inet_ioctl+0x65/0x90
[ 61.306415] [ 61.306415] [<
c1389b54>] sock_ioctl+0x124/0x2b0
[ 61.306415] [ 61.306415] [<
c113cf7c>] do_vfs_ioctl+0x7c/0x790
[ 61.306415] [ 61.306415] [<
c113d6b8>] SyS_ioctl+0x28/0x50
[ 61.306415] [ 61.306415] [<
c100179f>] do_int80_syscall_32+0x3f/0x110
[ 61.306415] [ 61.306415] [<
c14bba3f>] restore_all+0x0/0x61
[ 61.306415]
[ 61.306415]
the dependencies between the lock to be acquired[ 61.306415] and SOFTIRQ-irq-unsafe lock:
[ 61.306415] -> (&dev->lock){+.+...} ops: 56 {
[ 61.306415] HARDIRQ-ON-W at:
[ 61.306415] [ 61.306415] [<
c1075be7>] __lock_acquire+0x577/0x1770
[ 61.306415] [ 61.306415] [<
c107717c>] lock_acquire+0x7c/0x150
[ 61.306415] [ 61.306415] [<
c14b7add>] mutex_lock_nested+0x2d/0x4a0
[ 61.306415] [ 61.306415] [<
c133747d>] phy_probe+0x4d/0xc0
[ 61.306415] [ 61.306415] [<
c1338afe>] phy_attach_direct+0xbe/0x190
[ 61.306415] [ 61.306415] [<
c1338ca7>] phy_connect_direct+0x17/0x60
[ 61.306415] [ 61.306415] [<
c1338d23>] phy_connect+0x33/0x70
[ 61.306415] [ 61.306415] [<
d09357a0>] r6040_init_one+0x3a0/0x500 [r6040]
[ 61.306415] [ 61.306415] [<
c12a78c7>] pci_device_probe+0x77/0xd0
[ 61.306415] [ 61.306415] [<
c12f5e15>] driver_probe_device+0x145/0x280
[ 61.306415] [ 61.306415] [<
c12f5fd9>] __driver_attach+0x89/0x90
[ 61.306415] [ 61.306415] [<
c12f43ef>] bus_for_each_dev+0x4f/0x80
[ 61.306415] [ 61.306415] [<
c12f5954>] driver_attach+0x14/0x20
[ 61.306415] [ 61.306415] [<
c12f55b7>] bus_add_driver+0x197/0x210
[ 61.306415] [ 61.306415] [<
c12f6a21>] driver_register+0x51/0xd0
[ 61.306415] [ 61.306415] [<
c12a6955>] __pci_register_driver+0x45/0x50
[ 61.306415] [ 61.306415] [<
d0938017>] 0xd0938017
[ 61.306415] [ 61.306415] [<
c100043f>] do_one_initcall+0x2f/0x140
[ 61.306415] [ 61.306415] [<
c10e48c0>] do_init_module+0x4a/0x19b
[ 61.306415] [ 61.306415] [<
c10a680e>] load_module+0x1b2e/0x2070
[ 61.306415] [ 61.306415] [<
c10a6eb9>] SyS_finit_module+0x69/0x80
[ 61.306415] [ 61.306415] [<
c100179f>] do_int80_syscall_32+0x3f/0x110
[ 61.306415] [ 61.306415] [<
c14bba3f>] restore_all+0x0/0x61
[ 61.306415] SOFTIRQ-ON-W at:
[ 61.306415] [ 61.306415] [<
c1075c0c>] __lock_acquire+0x59c/0x1770
[ 61.306415] [ 61.306415] [<
c107717c>] lock_acquire+0x7c/0x150
[ 61.306415] [ 61.306415] [<
c14b7add>] mutex_lock_nested+0x2d/0x4a0
[ 61.306415] [ 61.306415] [<
c133747d>] phy_probe+0x4d/0xc0
[ 61.306415] [ 61.306415] [<
c1338afe>] phy_attach_direct+0xbe/0x190
[ 61.306415] [ 61.306415] [<
c1338ca7>] phy_connect_direct+0x17/0x60
[ 61.306415] [ 61.306415] [<
c1338d23>] phy_connect+0x33/0x70
[ 61.306415] [ 61.306415] [<
d09357a0>] r6040_init_one+0x3a0/0x500 [r6040]
[ 61.306415] [ 61.306415] [<
c12a78c7>] pci_device_probe+0x77/0xd0
[ 61.306415] [ 61.306415] [<
c12f5e15>] driver_probe_device+0x145/0x280
[ 61.306415] [ 61.306415] [<
c12f5fd9>] __driver_attach+0x89/0x90
[ 61.306415] [ 61.306415] [<
c12f43ef>] bus_for_each_dev+0x4f/0x80
[ 61.306415] [ 61.306415] [<
c12f5954>] driver_attach+0x14/0x20
[ 61.306415] [ 61.306415] [<
c12f55b7>] bus_add_driver+0x197/0x210
[ 61.306415] [ 61.306415] [<
c12f6a21>] driver_register+0x51/0xd0
[ 61.306415] [ 61.306415] [<
c12a6955>] __pci_register_driver+0x45/0x50
[ 61.306415] [ 61.306415] [<
d0938017>] 0xd0938017
[ 61.306415] [ 61.306415] [<
c100043f>] do_one_initcall+0x2f/0x140
[ 61.306415] [ 61.306415] [<
c10e48c0>] do_init_module+0x4a/0x19b
[ 61.306415] [ 61.306415] [<
c10a680e>] load_module+0x1b2e/0x2070
[ 61.306415] [ 61.306415] [<
c10a6eb9>] SyS_finit_module+0x69/0x80
[ 61.306415] [ 61.306415] [<
c100179f>] do_int80_syscall_32+0x3f/0x110
[ 61.306415] [ 61.306415] [<
c14bba3f>] restore_all+0x0/0x61
[ 61.306415] INITIAL USE at:
[ 61.306415] [ 61.306415] [<
c107586e>] __lock_acquire+0x1fe/0x1770
[ 61.306415] [ 61.306415] [<
c107717c>] lock_acquire+0x7c/0x150
[ 61.306415] [ 61.306415] [<
c14b7add>] mutex_lock_nested+0x2d/0x4a0
[ 61.306415] [ 61.306415] [<
c133747d>] phy_probe+0x4d/0xc0
[ 61.306415] [ 61.306415] [<
c1338afe>] phy_attach_direct+0xbe/0x190
[ 61.306415] [ 61.306415] [<
c1338ca7>] phy_connect_direct+0x17/0x60
[ 61.306415] [ 61.306415] [<
c1338d23>] phy_connect+0x33/0x70
[ 61.306415] [ 61.306415] [<
d09357a0>] r6040_init_one+0x3a0/0x500 [r6040]
[ 61.306415] [ 61.306415] [<
c12a78c7>] pci_device_probe+0x77/0xd0
[ 61.306415] [ 61.306415] [<
c12f5e15>] driver_probe_device+0x145/0x280
[ 61.306415] [ 61.306415] [<
c12f5fd9>] __driver_attach+0x89/0x90
[ 61.306415] [ 61.306415] [<
c12f43ef>] bus_for_each_dev+0x4f/0x80
[ 61.306415] [ 61.306415] [<
c12f5954>] driver_attach+0x14/0x20
[ 61.306415] [ 61.306415] [<
c12f55b7>] bus_add_driver+0x197/0x210
[ 61.306415] [ 61.306415] [<
c12f6a21>] driver_register+0x51/0xd0
[ 61.306415] [ 61.306415] [<
c12a6955>] __pci_register_driver+0x45/0x50
[ 61.306415] [ 61.306415] [<
d0938017>] 0xd0938017
[ 61.306415] [ 61.306415] [<
c100043f>] do_one_initcall+0x2f/0x140
[ 61.306415] [ 61.306415] [<
c10e48c0>] do_init_module+0x4a/0x19b
[ 61.306415] [ 61.306415] [<
c10a680e>] load_module+0x1b2e/0x2070
[ 61.306415] [ 61.306415] [<
c10a6eb9>] SyS_finit_module+0x69/0x80
[ 61.306415] [ 61.306415] [<
c100179f>] do_int80_syscall_32+0x3f/0x110
[ 61.306415] [ 61.306415] [<
c14bba3f>] restore_all+0x0/0x61
[ 61.306415] }
[ 61.306415] ... key at: [<
c1f28f39>] __key.43998+0x0/0x8
[ 61.306415] ... acquired at:
[ 61.306415] [ 61.306415] [<
c1074a32>] check_irq_usage+0x42/0xb0
[ 61.306415] [ 61.306415] [<
c107677c>] __lock_acquire+0x110c/0x1770
[ 61.306415] [ 61.306415] [<
c107717c>] lock_acquire+0x7c/0x150
[ 61.306415] [ 61.306415] [<
c14b7add>] mutex_lock_nested+0x2d/0x4a0
[ 61.306415] [ 61.306415] [<
c1336276>] phy_stop+0x16/0x80
[ 61.306415] [ 61.306415] [<
d0934ce9>] r6040_close+0x89/0x230 [r6040]
[ 61.306415] [ 61.306415] [<
c13a0a91>] __dev_close_many+0x61/0xa0
[ 61.306415] [ 61.306415] [<
c13a0bbf>] __dev_close+0x1f/0x30
[ 61.306415] [ 61.306415] [<
c13a9127>] __dev_change_flags+0x87/0x150
[ 61.306415] [ 61.306415] [<
c13a9213>] dev_change_flags+0x23/0x60
[ 61.306415] [ 61.306415] [<
c1416238>] devinet_ioctl+0x5f8/0x6f0
[ 61.306415] [ 61.306415] [<
c1417f75>] inet_ioctl+0x65/0x90
[ 61.306415] [ 61.306415] [<
c1389b54>] sock_ioctl+0x124/0x2b0
[ 61.306415] [ 61.306415] [<
c113cf7c>] do_vfs_ioctl+0x7c/0x790
[ 61.306415] [ 61.306415] [<
c113d6b8>] SyS_ioctl+0x28/0x50
[ 61.306415] [ 61.306415] [<
c100179f>] do_int80_syscall_32+0x3f/0x110
[ 61.306415] [ 61.306415] [<
c14bba3f>] restore_all+0x0/0x61
[ 61.306415]
[ 61.306415]
[ 61.306415] stack backtrace:
[ 61.306415] CPU: 0 PID: 449 Comm: ifconfig Not tainted
4.9.0-gb898d2d-manuel #1
[ 61.306415] Call Trace:
[ 61.306415] dump_stack+0x16/0x19
[ 61.306415] check_usage+0x3f6/0x550
[ 61.306415] ? check_usage+0x4d/0x550
[ 61.306415] check_irq_usage+0x42/0xb0
[ 61.306415] __lock_acquire+0x110c/0x1770
[ 61.306415] lock_acquire+0x7c/0x150
[ 61.306415] ? phy_stop+0x16/0x80
[ 61.306415] mutex_lock_nested+0x2d/0x4a0
[ 61.306415] ? phy_stop+0x16/0x80
[ 61.306415] ? r6040_close+0x24/0x230 [r6040]
[ 61.306415] ? __delay+0x9/0x10
[ 61.306415] phy_stop+0x16/0x80
[ 61.306415] r6040_close+0x89/0x230 [r6040]
[ 61.306415] __dev_close_many+0x61/0xa0
[ 61.306415] __dev_close+0x1f/0x30
[ 61.306415] __dev_change_flags+0x87/0x150
[ 61.306415] dev_change_flags+0x23/0x60
[ 61.306415] devinet_ioctl+0x5f8/0x6f0
[ 61.306415] inet_ioctl+0x65/0x90
[ 61.306415] sock_ioctl+0x124/0x2b0
[ 61.306415] ? dlci_ioctl_set+0x30/0x30
[ 61.306415] do_vfs_ioctl+0x7c/0x790
[ 61.306415] ? trace_hardirqs_on+0xb/0x10
[ 61.306415] ? call_rcu_sched+0xd/0x10
[ 61.306415] ? __put_cred+0x32/0x50
[ 61.306415] ? SyS_faccessat+0x178/0x1e0
[ 61.306415] SyS_ioctl+0x28/0x50
[ 61.306415] do_int80_syscall_32+0x3f/0x110
[ 61.306415] entry_INT80_32+0x2f/0x2f
[ 61.306415] EIP: 0xb764d364
[ 61.306415] EFLAGS:
00000286 CPU: 0
[ 61.306415] EAX:
ffffffda EBX:
00000004 ECX:
00008914 EDX:
bfa99d7c
[ 61.306415] ESI:
bfa99e4c EDI:
fffffffe EBP:
00000004 ESP:
bfa99d58
[ 61.306415] DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 007b
[ 63.836607] r6040 0000:00:08.0 eth0: Link is Down
Signed-off-by: Manuel Bessler <manuel.bessler@sensus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Mon, 12 Dec 2016 11:21:34 +0000 (14:21 +0300)]
irda: w83977af_ir: cleanup an indent issue
In commit
99d8d2159d7c ("irda: w83977af_ir: Neaten logging"), we
accidentally added an extra tab to these lines.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Wed, 14 Dec 2016 23:12:53 +0000 (00:12 +0100)]
net: sfc: use new api ethtool_{get|set}_link_ksettings
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Bert Kenward <bkenward@solarflare.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Wed, 14 Dec 2016 09:01:58 +0000 (10:01 +0100)]
net: davicom: dm9000: use new api ethtool_{get|set}_link_ksettings
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Mon, 12 Dec 2016 22:28:33 +0000 (23:28 +0100)]
net: cirrus: ep93xx: use new api ethtool_{get|set}_link_ksettings
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Sun, 11 Dec 2016 23:27:49 +0000 (00:27 +0100)]
net: chelsio: cxgb3: use new api ethtool_{get|set}_link_ksettings
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Sun, 11 Dec 2016 21:47:50 +0000 (22:47 +0100)]
net: chelsio: cxgb2: use new api ethtool_{get|set}_link_ksettings
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 18 Dec 2016 02:27:45 +0000 (21:27 -0500)]
Merge branch 'bpf-fixes'
Daniel Borkmann says:
====================
Couple of BPF fixes
This set contains three BPF fixes for net, one that addresses the
complaint from Geert wrt static allocations, and the other is a fix
wrt mem accounting that I found recently during testing and there's
still one more fix on the map value marking.
Thanks!
v1 -> v2:
- Patch 1 as is.
- Fixed kbuild bot issue by letting charging helpers stay in the
syscall.c, since there locked_vm is valid and only export the
ones needed by bpf_prog_realloc(). Add empty stubs in case the
bpf syscall is not enabled.
- Added patch 3 that addresses one more issue in map val marking.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sun, 18 Dec 2016 00:52:59 +0000 (01:52 +0100)]
bpf: fix mark_reg_unknown_value for spilled regs on map value marking
Martin reported a verifier issue that hit the BUG_ON() for his
test case in the mark_reg_unknown_value() function:
[ 202.861380] kernel BUG at kernel/bpf/verifier.c:467!
[...]
[ 203.291109] Call Trace:
[ 203.296501] [<
ffffffff811364d5>] mark_map_reg+0x45/0x50
[ 203.308225] [<
ffffffff81136558>] mark_map_regs+0x78/0x90
[ 203.320140] [<
ffffffff8113938d>] do_check+0x226d/0x2c90
[ 203.331865] [<
ffffffff8113a6ab>] bpf_check+0x48b/0x780
[ 203.343403] [<
ffffffff81134c8e>] bpf_prog_load+0x27e/0x440
[ 203.355705] [<
ffffffff8118a38f>] ? handle_mm_fault+0x11af/0x1230
[ 203.369158] [<
ffffffff812d8188>] ? security_capable+0x48/0x60
[ 203.382035] [<
ffffffff811351a4>] SyS_bpf+0x124/0x960
[ 203.393185] [<
ffffffff810515f6>] ? __do_page_fault+0x276/0x490
[ 203.406258] [<
ffffffff816db320>] entry_SYSCALL_64_fastpath+0x13/0x94
This issue got uncovered after the fix in
a08dd0da5307 ("bpf: fix
regression on verifier pruning wrt map lookups"). The reason why it
wasn't noticed before was, because as mentioned in
a08dd0da5307,
mark_map_regs() was doing the id matching incorrectly based on the
uncached regs[regno].id. So, in the first loop, we walked all regs
and as soon as we found regno == i, then this reg's id was cleared
when calling mark_reg_unknown_value() thus that every subsequent
register was probed against id of 0 (which, in combination with the
PTR_TO_MAP_VALUE_OR_NULL type is an invalid condition that no other
register state can hold), and therefore wasn't type transitioned such
as in the spilled register case for the second loop.
Now since that got fixed, it turned out that
57a09bf0a416 ("bpf:
Detect identical PTR_TO_MAP_VALUE_OR_NULL registers") used
mark_reg_unknown_value() incorrectly for the spilled regs, and thus
hitting the BUG_ON() in some cases due to regno >= MAX_BPF_REG.
Although spilled regs have the same type as the non-spilled regs
for the verifier state, that is, struct bpf_reg_state, they are
semantically different from the non-spilled regs. In other words,
there can be up to 64 (MAX_BPF_STACK / BPF_REG_SIZE) spilled regs
in the stack, for example, register R<x> could have been spilled by
the program to stack location X, Y, Z, and in mark_map_regs() we
need to scan these stack slots of type STACK_SPILL for potential
registers that we have to transition from PTR_TO_MAP_VALUE_OR_NULL.
Therefore, depending on the location, the spilled_regs regno can
be a lot higher than just MAX_BPF_REG's value since we operate on
stack instead. The reset in mark_reg_unknown_value() itself is
just fine, only that the BUG_ON() was inappropriate for this. Fix
it by making a __mark_reg_unknown_value() version that can be
called from mark_map_reg() generically; we know for the non-spilled
case that the regno is always < MAX_BPF_REG anyway.
Fixes: 57a09bf0a416 ("bpf: Detect identical PTR_TO_MAP_VALUE_OR_NULL registers")
Reported-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sun, 18 Dec 2016 00:52:58 +0000 (01:52 +0100)]
bpf: fix overflow in prog accounting
Commit
aaac3ba95e4c ("bpf: charge user for creation of BPF maps and
programs") made a wrong assumption of charging against prog->pages.
Unlike map->pages, prog->pages are still subject to change when we
need to expand the program through bpf_prog_realloc().
This can for example happen during verification stage when we need to
expand and rewrite parts of the program. Should the required space
cross a page boundary, then prog->pages is not the same anymore as
its original value that we used to bpf_prog_charge_memlock() on. Thus,
we'll hit a wrap-around during bpf_prog_uncharge_memlock() when prog
is freed eventually. I noticed this that despite having unlimited
memlock, programs suddenly refused to load with EPERM error due to
insufficient memlock.
There are two ways to fix this issue. One would be to add a cached
variable to struct bpf_prog that takes a snapshot of prog->pages at the
time of charging. The other approach is to also account for resizes. I
chose to go with the latter for a couple of reasons: i) We want accounting
rather to be more accurate instead of further fooling limits, ii) adding
yet another page counter on struct bpf_prog would also be a waste just
for this purpose. We also do want to charge as early as possible to
avoid going into the verifier just to find out later on that we crossed
limits. The only place that needs to be fixed is bpf_prog_realloc(),
since only here we expand the program, so we try to account for the
needed delta and should we fail, call-sites check for outcome anyway.
On cBPF to eBPF migrations, we don't grab a reference to the user as
they are charged differently. With that in place, my test case worked
fine.
Fixes: aaac3ba95e4c ("bpf: charge user for creation of BPF maps and programs")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sun, 18 Dec 2016 00:52:57 +0000 (01:52 +0100)]
bpf: dynamically allocate digest scratch buffer
Geert rightfully complained that
7bd509e311f4 ("bpf: add prog_digest
and expose it via fdinfo/netlink") added a too large allocation of
variable 'raw' from bss section, and should instead be done dynamically:
# ./scripts/bloat-o-meter kernel/bpf/core.o.1 kernel/bpf/core.o.2
add/remove: 3/0 grow/shrink: 0/0 up/down: 33291/0 (33291)
function old new delta
raw - 32832 +32832
[...]
Since this is only relevant during program creation path, which can be
considered slow-path anyway, lets allocate that dynamically and be not
implicitly dependent on verifier mutex. Move bpf_prog_calc_digest() at
the beginning of replace_map_fd_with_map_ptr() and also error handling
stays straight forward.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 18 Dec 2016 01:05:49 +0000 (17:05 -0800)]
Merge git://git./linux/kernel/git/cmetcalf/linux-tile
Pull arch/tile updates from Chris Metcalf:
"Another grab-bag of miscellaneous changes"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: use __ro_after_init instead of tile-specific __write_once
tile: migrate exception table users off module.h and onto extable.h
tile: remove #pragma unroll from finv_buffer_remote()
tile-module: Rename jump labels in module_alloc()
tile-module: Use kmalloc_array() in module_alloc()
tile/pci_gx: fix spelling mistake: "delievered" -> "delivered"
Linus Torvalds [Sun, 18 Dec 2016 00:47:31 +0000 (16:47 -0800)]
Merge tag 'kvmgt-vfio-mdev-for-v4.10-rc1' of git://github.com/01org/gvt-linux
Pull i915/gvt KVMGT updates from Zhenyu Wang:
"KVMGT support depending on the VFIO/mdev framework"
* tag 'kvmgt-vfio-mdev-for-v4.10-rc1' of git://github.com/01org/gvt-linux:
drm/i915/gvt/kvmgt: add vfio/mdev support to KVMGT
drm/i915/gvt/kvmgt: read/write GPA via KVM API
drm/i915/gvt/kvmgt: replace kmalloc() by kzalloc()
Linus Torvalds [Sun, 18 Dec 2016 00:45:00 +0000 (16:45 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input subsystem updates from Dmitry Torokhov:
- updated support for Synaptics RMI4 devices, including support for
SMBus controllers, firmware update support, sensor tuning, and PS/2
guest support
- ALPS driver now supports tracksticks on SS5 controllers
- i8042 now uses chassis info to skip selftest on Asus laptops as list
of individual models became too unwieldy
- miscellaneous fixes to other drivers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (67 commits)
Input: imx6ul_tsc - generalize the averaging property
Input: drv260x - use generic device properties
Input: drv260x - use temporary for &client->dev
Input: drv260x - fix input device's parent assignment
Input: synaptics-rmi4 - add support for F34 V7 bootloader
Input: drv260x - fix initializing overdrive voltage
Input: ALPS - fix protcol -> protocol
Input: i8042 - comment #else/#endif of CONFIG_PNP
Input: lpc32xx-keys - fix invalid error handling of a requested irq
Input: synaptics-rmi4 - fix debug for sensor clip
Input: synaptics-rmi4 - store the attn data in the driver
Input: synaptics-rmi4 - allow to add attention data
Input: synaptics-rmi4 - f03 - grab data passed by transport device
Input: synaptics-rmi4 - add support for F03
Input: imx6ul_tsc - convert int to u32
Input: imx6ul_tsc - add mask when set REG_ADC_CFG
Input: synaptics-rmi4 - have only one struct platform data
Input: synaptics-rmi4 - remove EXPORT_SYMBOL_GPL for internal functions
Input: synaptics-rmi4 - remove mutex calls while updating the firmware
Input: drv2667 - fix misuse of regmap_update_bits
...
Linus Torvalds [Sun, 18 Dec 2016 00:41:10 +0000 (16:41 -0800)]
Merge tag 'for-linus-
20161216' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"Nothing enormous here, though notably we have some of the first work
of a few new maintainers. I think for now I'll still be sending pull
requests, but that's open to change in the future. Summary:
Core:
- dynamic BDI object allocation (resolves some problems when built as
a module)
- cleanups in the ooblayout handling
NAND:
- new tango NAND controller driver
- new ox820 NAND controller driver
- addition of a new full-ID entry in the nand_ids table
- rework of the s3c240 driver to support DT
- extension of the nand_sdr_timings to expose tCCS, tPROG and tR
- addition of a new flag to ask the core to wait for tCCS when
sending a RNDIN/RNDOUT command
- addition of a new flag to ask the core to let the controller driver
send the READ/PROGPAGE command
Minor fixes/cleanup/cosmetic changes:
- properly support 512 ECC step size in the sunxi driver
- improve the error messages in the PXA probe path
- fix module autoload in the omap2 driver
- cleanup of several nand drivers to return nand_scan{_tail}() error
code instead of returning -EIO
- various cleanups in the denali driver
- fix an error check in nandsim
SPI NOR:
- new flash IDs
- wait for Spansion flash to be ready after quad-enable
- error handling fixes for Candence QSPI
- constify some structures in Freescale QSPI driver"
* tag 'for-linus-
20161216' of git://git.infradead.org/linux-mtd: (71 commits)
mtd: Allocate bdi objects dynamically
mtd: nand: tango: Add standard legalese header
mtd: maps: add missing iounmap() in error path
mtd: spi-nor: constify fsl_qspi_devtype_data
mtd: spi-nor: Add support for mr25h40
mtd: spi-nor: Add support for N25Q016A
mtd: spi-nor: Add at25df321 spi-nor flash support
mtd: spi-nor: Fix some error codes in cqspi_setup_flash()
mtd: spi-nor: Off by one in cqspi_setup_flash()
mtd: spi-nor: add support for s25fl208k
mtd: spi-nor: fix flags for s25fl128s
mtd: spi-nor: fix spansion quad enable
mtd: spi-nor: add Macronix mx25u25635f to list of known devices.
mtd: mtdswap: fix spelling mistake "erassure" -> "erasure"
mtd: bcm47xxpart: fix parsing first block after aligned TRX
mtd: nand: tango: Use nand_to_mtd() instead of directly accessing chip->mtd
mtd: remove unneeded initializer in mtd_ooblayout_count_bytes()
mtd: use min_t() to refactor mtd_ooblayout_{get, set}_bytes()
mtd: remove unneeded initializer in mtd_ooblayout_{get, set}_bytes()
mtd: nand: nandsim: fix error check
...
Linus Torvalds [Sun, 18 Dec 2016 00:32:27 +0000 (16:32 -0800)]
Merge branch 'misc' of git://git./linux/kernel/git/mmarek/kbuild
Pull kbuild misc updates from Michal Marek:
- one new coccinelle check and improvements to irqf_oneshot.cocci
- 'make rpm' POSIX compatibility fix
- 'make deb-pkg' arm64 cross-compiling fix. I forgot to send this one
during the v4.9 rc-phase, therefor the pull request is based on -rc6
and not -rc1
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
Coccinelle: misc: Add support for devm variant in all modes
Coccinelle: misc: Improve the result given by context mode
Coccinelle: misc: Improve the matching of rules
kbuild/mkspec: avoid using brace expansion
Coccinelle: Add misc/boolconv.cocci
builddeb: fix cross-building to arm64 producing host-arch debs
Linus Torvalds [Sun, 18 Dec 2016 00:30:24 +0000 (16:30 -0800)]
Merge branch 'kconfig' of git://git./linux/kernel/git/mmarek/kbuild
Pull kconfig updates from Michal Marek:
- 'make xconfig' gui fixes
- 'make nconfig' fix for options with long prompts
- fix 'make nconfig' warning when pkg-config forces -D_GNU_SOURCE
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
xconfig: fix missing suboption and help panels on first run
xconfig: fix 'Show Debug' functionality
kconfig/nconf: Fix hang when editing symbol with a long prompt
Scripts: kconfig: nconf: fix _GNU_SOURCE redefined warning
Linus Torvalds [Sun, 18 Dec 2016 00:24:13 +0000 (16:24 -0800)]
Merge branch 'kbuild' of git://git./linux/kernel/git/mmarek/kbuild
Pull kbuild updates from Michal Marek:
- prototypes for x86 asm-exported symbols (Adam Borowski) and a warning
about missing CRCs (Nick Piggin)
- asm-exports fix for LTO (Nicolas Pitre)
- thin archives improvements (Nick Piggin)
- linker script fix for CONFIG_LD_DEAD_CODE_DATA_ELIMINATION (Nick
Piggin)
- genksyms support for __builtin_va_list keyword
- misc minor fixes
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
x86/kbuild: enable modversions for symbols exported from asm
kbuild: fix scripts/adjust_autoksyms.sh* for the no modules case
scripts/kallsyms: remove last remnants of --page-offset option
make use of make variable CURDIR instead of calling pwd
kbuild: cmd_export_list: tighten the sed script
kbuild: minor improvement for thin archives build
kbuild: modpost warn if export version crc is missing
kbuild: keep data tables through dead code elimination
kbuild: improve linker compatibility with lib-ksyms.o build
genksyms: Regenerate parser
kbuild/genksyms: handle va_list type
kbuild: thin archives for multi-y targets
kbuild: kallsyms allow 3-pass generation if symbols size has changed
Linus Torvalds [Sun, 18 Dec 2016 00:00:34 +0000 (16:00 -0800)]
Merge tag 'docs-4.10-2' of git://git.lwn.net/linux
Pull more documentation updates from Jonathan Corbet:
"This converts the crypto DocBook to Sphinx"
* tag 'docs-4.10-2' of git://git.lwn.net/linux:
crypto: doc - optimize compilation
crypto: doc - clarify AEAD memory structure
crypto: doc - remove crypto_alloc_ablkcipher
crypto: doc - add KPP documentation
crypto: doc - fix separation of cipher / req API
crypto: doc - fix source comments for Sphinx
crypto: doc - remove crypto API DocBook
crypto: doc - convert crypto API documentation to Sphinx
David S. Miller [Sat, 17 Dec 2016 17:00:26 +0000 (12:00 -0500)]
Merge branch 'gtp-fixes'
Pablo Neira Ayuso says:
====================
GTP tunneling fixes for net
The following patchset contains two GTP tunneling fixes for your net
tree, they are:
1) Offset to IPv4 header in gtp_check_src_ms_ipv4() is incorrect, thus
this function always succeeds and therefore this defeats this sanity
check. This allows packets that have no PDP to go though, patch from
Lionel Gauthier.
2) According to Note 0 of Figure 2 in Section 6 of 3GPP TS 29.060 v13.5.0
Release 13, always set GTPv1 reserved bit to zero. This may cause
interoperability problems, patch from Harald Welte.
Please, apply, thanks a lot!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Harald Welte [Thu, 15 Dec 2016 21:35:53 +0000 (22:35 +0100)]
gtp: Fix initialization of Flags octet in GTPv1 header
When generating a GTPv1 header in gtp1_push_header(), initialize the
'reserved' bit to zero. All 3GPP specifications for GTPv1 from Release
99 through Release 13 agree that a transmitter shall set this bit to
zero, see e.g. Note 0 of Figure 2 in Section 6 of 3GPP TS 29.060 v13.5.0
Release 13, available from
http://www.etsi.org/deliver/etsi_ts/129000_129099/129060/13.05.00_60/ts_129060v130500p.pdf
Signed-off-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lionel Gauthier [Thu, 15 Dec 2016 21:35:52 +0000 (22:35 +0100)]
gtp: gtp_check_src_ms_ipv4() always return success
gtp_check_src_ms_ipv4() did not find the PDP context matching with the
UE IP address because the memory location is not right, but the result
is inverted by the Boolean "not" operator. So whatever is the PDP
context, any call to this function is successful.
Signed-off-by: Lionel Gauthier <Lionel.Gauthier@eurecom.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kees Cook [Sat, 17 Dec 2016 01:03:39 +0000 (17:03 -0800)]
net/x25: use designated initializers
Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. These were identified during
allyesconfig builds of x86, arm, and arm64, with most initializer fixes
extracted from grsecurity.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kees Cook [Sat, 17 Dec 2016 01:01:42 +0000 (17:01 -0800)]
isdn: use designated initializers
Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. These were identified during
allyesconfig builds of x86, arm, and arm64, with most initializer fixes
extracted from grsecurity.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kees Cook [Sat, 17 Dec 2016 01:00:54 +0000 (17:00 -0800)]
bna: use designated initializers
Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. These were identified during
allyesconfig builds of x86, arm, and arm64, with most initializer fixes
extracted from grsecurity.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kees Cook [Sat, 17 Dec 2016 00:59:18 +0000 (16:59 -0800)]
WAN: use designated initializers
Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. These were identified during
allyesconfig builds of x86, arm, and arm64, with most initializer fixes
extracted from grsecurity.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kees Cook [Sat, 17 Dec 2016 00:58:58 +0000 (16:58 -0800)]
net: use designated initializers
Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. These were identified during
allyesconfig builds of x86, arm, and arm64, with most initializer fixes
extracted from grsecurity.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kees Cook [Sat, 17 Dec 2016 00:58:43 +0000 (16:58 -0800)]
ATM: use designated initializers
Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. These were identified during
allyesconfig builds of x86, arm, and arm64, with most initializer fixes
extracted from grsecurity.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kees Cook [Sat, 17 Dec 2016 00:58:06 +0000 (16:58 -0800)]
isdn/gigaset: use designated initializers
Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. These were identified during
allyesconfig builds of x86, arm, and arm64, with most initializer fixes
extracted from grsecurity.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 17 Dec 2016 16:48:56 +0000 (11:48 -0500)]
Merge branch 'virtio_net-XDP'
John Fastabend says:
====================
XDP for virtio_net
This implements virtio_net for the mergeable buffers and big_packet
modes. I tested this with vhost_net running on qemu and did not see
any issues. For testing num_buf > 1 I added a hack to vhost driver
to only but 100 bytes per buffer.
There are some restrictions for XDP to be enabled and work well
(see patch 3) for more details.
1. GUEST_TSO{4|6} must be off
2. MTU must be less than PAGE_SIZE
3. queues must be available to dedicate to XDP
4. num_bufs received in mergeable buffers must be 1
5. big_packet mode must have all data on single page
To test this I used pktgen in the hypervisor and ran the XDP sample
programs xdp1 and xdp2 from ./samples/bpf in the host. The default
mode that is used with these patches with Linux guest and QEMU/Linux
hypervisor is the mergeable buffers mode. I tested this mode for 2+
days running xdp2 without issues. Additionally I did a series of
driver unload/load tests to check the allocate/release paths.
To test the big_packets path I applied the following simple patch against
the virtio driver forcing big_packets mode,
--- a/drivers/net/virtio_net.c
+++ b/drivers/net/virtio_net.c
@@ -2242,7 +2242,7 @@ static int virtnet_probe(struct virtio_device *vdev)
vi->big_packets = true;
if (virtio_has_feature(vdev, VIRTIO_NET_F_MRG_RXBUF))
- vi->mergeable_rx_bufs = true;
+ vi->mergeable_rx_bufs = false;
if (virtio_has_feature(vdev, VIRTIO_NET_F_MRG_RXBUF) ||
virtio_has_feature(vdev, VIRTIO_F_VERSION_1))
I then repeated the tests with xdp1 and xdp2. After letting them run
for a few hours I called it good enough.
Testing the unexpected case where virtio receives a packet across
multiple buffers required patching the hypervisor vhost driver to
convince it to send these unexpected packets. Then I used ping with
the -s option to trigger the case with multiple buffers. This mode
is not expected to be used but as MST pointed out per spec it is
not strictly speaking illegal to generate multi-buffer packets so we
need someway to handle these. The following patch can be used to
generate multiple buffers,
--- a/drivers/vhost/vhost.c
+++ b/drivers/vhost/vhost.c
@@ -1777,7 +1777,8 @@ static int translate_desc(struct vhost_virtqueue
*vq, u64
_iov = iov + ret;
size = node->size - addr + node->start;
- _iov->iov_len = min((u64)len - s, size);
+ printk("%s: build 100 length headers!\n", __func__);
+ _iov->iov_len = min((u64)len - s, (u64)100);//size);
_iov->iov_base = (void __user *)(unsigned long)
(node->userspace_addr + addr - node->start);
s += size;
The qemu command I most frequently used for testing (although I did test
various other combinations of devices) is the following,
./x86_64-softmmu/qemu-system-x86_64 \
-hda /var/lib/libvirt/images/Fedora-test0.img \
-m 4096 -enable-kvm -smp 2 \
-netdev tap,id=hn0,queues=4,vhost=on \
-device virtio-net-pci,netdev=hn0,mq=on,vectors=9,guest_tso4=off,guest_tso6=off \
-serial stdio
The options 'guest_tso4=off,guest_tso6=off' are required because we
do not support LRO with XDP at the moment.
Please review any comments/feedback welcome as always.
====================
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Thu, 15 Dec 2016 20:14:36 +0000 (12:14 -0800)]
virtio_net: xdp, add slowpath case for non contiguous buffers
virtio_net XDP support expects receive buffers to be contiguous.
If this is not the case we enable a slowpath to allow connectivity
to continue but at a significan performance overhead associated with
linearizing data. To make it painfully aware to users that XDP is
running in a degraded mode we throw an xdp buffer error.
To linearize packets we allocate a page and copy the segments of
the data, including the header, into it. After this the page can be
handled by XDP code flow as normal.
Then depending on the return code the page is either freed or sent
to the XDP xmit path. There is no attempt to optimize this path.
This case is being handled simple as a precaution in case some
unknown backend were to generate packets in this form. To test this
I had to hack qemu and force it to generate these packets. I do not
expect this case to be generated by "real" backends.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Thu, 15 Dec 2016 20:14:13 +0000 (12:14 -0800)]
virtio_net: add XDP_TX support
This adds support for the XDP_TX action to virtio_net. When an XDP
program is run and returns the XDP_TX action the virtio_net XDP
implementation will transmit the packet on a TX queue that aligns
with the current CPU that the XDP packet was processed on.
Before sending the packet the header is zeroed. Also XDP is expected
to handle checksum correctly so no checksum offload support is
provided.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Thu, 15 Dec 2016 20:13:49 +0000 (12:13 -0800)]
virtio_net: add dedicated XDP transmit queues
XDP requires using isolated transmit queues to avoid interference
with normal networking stack (BQL, NETDEV_TX_BUSY, etc). This patch
adds a XDP queue per cpu when a XDP program is loaded and does not
expose the queues to the OS via the normal API call to
netif_set_real_num_tx_queues(). This way the stack will never push
an skb to these queues.
However virtio/vhost/qemu implementation only allows for creating
TX/RX queue pairs at this time so creating only TX queues was not
possible. And because the associated RX queues are being created I
went ahead and exposed these to the stack and let the backend use
them. This creates more RX queues visible to the network stack than
TX queues which is worth mentioning but does not cause any issues as
far as I can tell.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Thu, 15 Dec 2016 20:13:24 +0000 (12:13 -0800)]
virtio_net: Add XDP support
This adds XDP support to virtio_net. Some requirements must be
met for XDP to be enabled depending on the mode. First it will
only be supported with LRO disabled so that data is not pushed
across multiple buffers. Second the MTU must be less than a page
size to avoid having to handle XDP across multiple pages.
If mergeable receive is enabled this patch only supports the case
where header and data are in the same buf which we can check when
a packet is received by looking at num_buf. If the num_buf is
greater than 1 and a XDP program is loaded the packet is dropped
and a warning is thrown. When any_header_sg is set this does not
happen and both header and data is put in a single buffer as expected
so we check this when XDP programs are loaded. Subsequent patches
will process the packet in a degraded mode to ensure connectivity
and correctness is not lost even if backend pushes packets into
multiple buffers.
If big packets mode is enabled and MTU/LRO conditions above are
met then XDP is allowed.
This patch was tested with qemu with vhost=on and vhost=off where
mergeable and big_packet modes were forced via hard coding feature
negotiation. Multiple buffers per packet was forced via a small
test patch to vhost.c in the vhost=on qemu mode.
Suggested-by: Shrijeet Mukherjee <shrijeet@gmail.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Thu, 15 Dec 2016 20:12:54 +0000 (12:12 -0800)]
net: xdp: add invalid buffer warning
This adds a warning for drivers to use when encountering an invalid
buffer for XDP. For normal cases this should not happen but to catch
this in virtual/qemu setups that I may not have expected from the
emulation layer having a standard warning is useful.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Thu, 15 Dec 2016 15:05:52 +0000 (23:05 +0800)]
sctp: sctp_transport_lookup_process should rcu_read_unlock when transport is null
Prior to this patch, sctp_transport_lookup_process didn't rcu_read_unlock
when it failed to find a transport by sctp_addrs_lookup_transport.
This patch is to fix it by moving up rcu_read_unlock right before checking
transport and also to remove the out path.
Fixes: 1cceda784980 ("sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Thu, 15 Dec 2016 15:00:55 +0000 (23:00 +0800)]
sctp: sctp_epaddr_lookup_transport should be protected by rcu_read_lock
Since commit
7fda702f9315 ("sctp: use new rhlist interface on sctp transport
rhashtable"), sctp has changed to use rhlist_lookup to look up transport, but
rhlist_lookup doesn't call rcu_read_lock inside, unlike rhashtable_lookup_fast.
It is called in sctp_epaddr_lookup_transport and sctp_addrs_lookup_transport.
sctp_addrs_lookup_transport is always in the protection of rcu_read_lock(),
as __sctp_lookup_association is called in rx path or sctp_lookup_association
which are in the protection of rcu_read_lock() already.
But sctp_epaddr_lookup_transport is called by sctp_endpoint_lookup_assoc, it
doesn't call rcu_read_lock, which may cause "suspicious rcu_dereference_check
usage' in __rhashtable_lookup.
This patch is to fix it by adding rcu_read_lock in sctp_endpoint_lookup_assoc
before calling sctp_epaddr_lookup_transport.
Fixes: 7fda702f9315 ("sctp: use new rhlist interface on sctp transport rhashtable")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 17 Dec 2016 16:43:05 +0000 (11:43 -0500)]
Merge branch 'dpaa_eth-fixes'
Madalin Bucur says:
====================
dpaa_eth: a couple of fixes
This patch set introduces big endian accessors in the dpaa_eth driver
making sure accesses to the QBMan HW are correct on little endian
platforms. Removing a redundant Kconfig dependency on FSL_SOC.
Adding myself as maintainer of the dpaa_eth driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Thu, 15 Dec 2016 13:13:06 +0000 (15:13 +0200)]
MAINTAINERS: net: add entry for Freescale QorIQ DPAA Ethernet driver
Add record for Freescale QORIQ DPAA Ethernet driver adding myself as
maintainer.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Thu, 15 Dec 2016 13:13:05 +0000 (15:13 +0200)]
dpaa_eth: remove redundant dependency on FSL_SOC
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Thu, 15 Dec 2016 13:13:04 +0000 (15:13 +0200)]
dpaa_eth: use big endian accessors
Ensure correct access to the big endian QMan HW through proper
accessors.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LABBE Corentin [Thu, 15 Dec 2016 10:42:50 +0000 (11:42 +0100)]
irda: irnet: add member name to the miscdevice declaration
Since the struct miscdevice have many members, it is dangerous to init
it without members name relying only on member order.
This patch add member name to the init declaration.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LABBE Corentin [Thu, 15 Dec 2016 10:42:49 +0000 (11:42 +0100)]
irda: irnet: Remove unused IRNET_MAJOR define
The IRNET_MAJOR define is not used, so this patch remove it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LABBE Corentin [Thu, 15 Dec 2016 10:42:48 +0000 (11:42 +0100)]
irnet: ppp: move IRNET_MINOR to include/linux/miscdevice.h
This patch move the define for IRNET_MINOR to include/linux/miscdevice.h
It is better that all minor number definitions are in the same place.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
LABBE Corentin [Thu, 15 Dec 2016 10:42:47 +0000 (11:42 +0100)]
irda: irnet: Move linux/miscdevice.h include
The only use of miscdevice is irda_ppp so no need to include
linux/miscdevice.h for all irda files.
This patch move the linux/miscdevice.h include to irnet_ppp.h
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LABBE Corentin [Thu, 15 Dec 2016 10:42:46 +0000 (11:42 +0100)]
irda: irproc.c: Remove unneeded linux/miscdevice.h include
irproc.c does not use any miscdevice so this patch remove this
unnecessary inclusion.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Mack [Thu, 15 Dec 2016 09:53:21 +0000 (10:53 +0100)]
bpf: cgroup: annotate pointers in struct cgroup_bpf with __rcu
The member 'effective' in 'struct cgroup_bpf' is protected by RCU.
Annotate it accordingly to squelch a sparse warning.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 17 Dec 2016 16:13:20 +0000 (11:13 -0500)]
Merge branch 'inet_csk_get_port-and-soreusport-fixes'
Tom Herbert says:
====================
inet: Fixes for inet_csk_get_port and soreusport
This patch set fixes a couple of issues I noticed while debugging our
softlockup issue in inet_csk_get_port.
- Don't allow jump into port scan in inet_csk_get_port if function
was called with non-zero port number (looking up explicit port
number).
- When inet_csk_get_port is called with zero port number (ie. perform
scan) an reuseport is set on the socket, don't match sockets that
also have reuseport set. The intent from the user should be
to get a new port number and then explictly bind other
sockets to that number using soreuseport.
Tested:
Ran first patch on production workload with no ill effect.
For second patch, ran a little listener application and first
demonstrated that unbound sockets with soreuseport can indeed
be bound to unrelated soreuseport sockets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Thu, 15 Dec 2016 00:54:16 +0000 (16:54 -0800)]
inet: Fix get port to handle zero port number with soreuseport set
A user may call listen with binding an explicit port with the intent
that the kernel will assign an available port to the socket. In this
case inet_csk_get_port does a port scan. For such sockets, the user may
also set soreuseport with the intent a creating more sockets for the
port that is selected. The problem is that the initial socket being
opened could inadvertently choose an existing and unreleated port
number that was already created with soreuseport.
This patch adds a boolean parameter to inet_bind_conflict that indicates
rather soreuseport is allowed for the check (in addition to
sk->sk_reuseport). In calls to inet_bind_conflict from inet_csk_get_port
the argument is set to true if an explicit port is being looked up (snum
argument is nonzero), and is false if port scan is done.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Thu, 15 Dec 2016 00:54:15 +0000 (16:54 -0800)]
inet: Don't go into port scan when looking for specific bind port
inet_csk_get_port is called with port number (snum argument) that may be
zero or nonzero. If it is zero, then the intent is to find an available
ephemeral port number to bind to. If snum is non-zero then the caller
is asking to allocate a specific port number. In the latter case we
never want to perform the scan in ephemeral port range. It is
conceivable that this can happen if the "goto again" in "tb_found:"
is done. This patch adds a check that snum is zero before doing
the "goto again".
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 15 Dec 2016 00:39:10 +0000 (01:39 +0100)]
bpf, test_verifier: fix a test case error result on unprivileged
Running ./test_verifier as unprivileged lets 1 out of 98 tests fail:
[...]
#71 unpriv: check that printk is disallowed FAIL
Unexpected error message!
0: (7a) *(u64 *)(r10 -8) = 0
1: (bf) r1 = r10
2: (07) r1 += -8
3: (b7) r2 = 8
4: (bf) r3 = r1
5: (85) call bpf_trace_printk#6
unknown func bpf_trace_printk#6
[...]
The test case is correct, just that the error outcome changed with
ebb676daa1a3 ("bpf: Print function name in addition to function id").
Same as with
e00c7b216f34 ("bpf: fix multiple issues in selftest suite
and samples") issue 2), so just fix up the function name.
Fixes: ebb676daa1a3 ("bpf: Print function name in addition to function id")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 15 Dec 2016 00:30:06 +0000 (01:30 +0100)]
bpf: fix regression on verifier pruning wrt map lookups
Commit
57a09bf0a416 ("bpf: Detect identical PTR_TO_MAP_VALUE_OR_NULL
registers") introduced a regression where existing programs stopped
loading due to reaching the verifier's maximum complexity limit,
whereas prior to this commit they were loading just fine; the affected
program has roughly 2k instructions.
What was found is that state pruning couldn't be performed effectively
anymore due to mismatches of the verifier's register state, in particular
in the id tracking. It doesn't mean that
57a09bf0a416 is incorrect per
se, but rather that verifier needs to perform a lot more work for the
same program with regards to involved map lookups.
Since commit
57a09bf0a416 is only about tracking registers with type
PTR_TO_MAP_VALUE_OR_NULL, the id is only needed to follow registers
until they are promoted through pattern matching with a NULL check to
either PTR_TO_MAP_VALUE or UNKNOWN_VALUE type. After that point, the
id becomes irrelevant for the transitioned types.
For UNKNOWN_VALUE, id is already reset to 0 via mark_reg_unknown_value(),
but not so for PTR_TO_MAP_VALUE where id is becoming stale. It's even
transferred further into other types that don't make use of it. Among
others, one example is where UNKNOWN_VALUE is set on function call
return with RET_INTEGER return type.
states_equal() will then fall through the memcmp() on register state;
note that the second memcmp() uses offsetofend(), so the id is part of
that since
d2a4dd37f6b4 ("bpf: fix state equivalence"). But the bisect
pointed already to
57a09bf0a416, where we really reach beyond complexity
limit. What I found was that states_equal() often failed in this
case due to id mismatches in spilled regs with registers in type
PTR_TO_MAP_VALUE. Unlike non-spilled regs, spilled regs just perform
a memcmp() on their reg state and don't have any other optimizations
in place, therefore also id was relevant in this case for making a
pruning decision.
We can safely reset id to 0 as well when converting to PTR_TO_MAP_VALUE.
For the affected program, it resulted in a ~17 fold reduction of
complexity and let the program load fine again. Selftest suite also
runs fine. The only other place where env->id_gen is used currently is
through direct packet access, but for these cases id is long living, thus
a different scenario.
Also, the current logic in mark_map_regs() is not fully correct when
marking NULL branch with UNKNOWN_VALUE. We need to cache the destination
reg's id in any case. Otherwise, once we marked that reg as UNKNOWN_VALUE,
it's id is reset and any subsequent registers that hold the original id
and are of type PTR_TO_MAP_VALUE_OR_NULL won't be marked UNKNOWN_VALUE
anymore, since mark_map_reg() reuses the uncached regs[regno].id that
was just overridden. Note, we don't need to cache it outside of
mark_map_regs(), since it's called once on this_branch and the other
time on other_branch, which are both two independent verifier states.
A test case for this is added here, too.
Fixes: 57a09bf0a416 ("bpf: Detect identical PTR_TO_MAP_VALUE_OR_NULL registers")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 14 Dec 2016 22:31:11 +0000 (14:31 -0800)]
net: vrf: Drop conntrack data after pass through VRF device on Tx
Locally originated traffic in a VRF fails in the presence of a POSTROUTING
rule. For example,
$ iptables -t nat -A POSTROUTING -s 11.1.1.0/24 -j MASQUERADE
$ ping -I red -c1 11.1.1.3
ping: Warning: source address might be selected on device other than red.
PING 11.1.1.3 (11.1.1.3) from 11.1.1.2 red: 56(84) bytes of data.
ping: sendmsg: Operation not permitted
Worse, the above causes random corruption resulting in a panic in random
places (I have not seen a consistent backtrace).
Call nf_reset to drop the conntrack info following the pass through the
VRF device. The nf_reset is needed on Tx but not Rx because of the order
in which NF_HOOK's are hit: on Rx the VRF device is after the real ingress
device and on Tx it is is before the real egress device. Connection
tracking should be tied to the real egress device and not the VRF device.
Fixes: 8f58336d3f78a ("net: Add ethernet header for pass through VRF device")
Fixes: 35402e3136634 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 14 Dec 2016 19:06:18 +0000 (11:06 -0800)]
net: vrf: Fix NAT within a VRF
Connection tracking with VRF is broken because the pass through the VRF
device drops the connection tracking info. Removing the call to nf_reset
allows DNAT and MASQUERADE to work across interfaces within a VRF.
Fixes: 73e20b761acf ("net: vrf: Add support for PREROUTING rules on vrf device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 17 Dec 2016 15:44:42 +0000 (10:44 -0500)]
Merge branch 'cls_flower-mask'
Paul Blakey says:
====================
net/sched: cls_flower: Fix mask handling
The series fix how the mask is being handled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey [Wed, 14 Dec 2016 17:00:58 +0000 (19:00 +0200)]
net/sched: cls_flower: Use masked key when calling HW offloads
Zero bits on the mask signify a "don't care" on the corresponding bits
in key. Some HWs require those bits on the key to be zero. Since these
bits are masked anyway, it's okay to provide the masked key to all
drivers.
Fixes: 5b33f48842fa ('net/flower: Introduce hardware offload support')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey [Wed, 14 Dec 2016 17:00:57 +0000 (19:00 +0200)]
net/sched: cls_flower: Use mask for addr_type
When addr_type is set, mask should also be set.
Fixes: 66530bdf85eb ('sched,cls_flower: set key address type when present')
Fixes: bc3103f1ed40 ('net/sched: cls_flower: Classify packet in ip tunnels')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bartosz Folta [Wed, 14 Dec 2016 06:39:15 +0000 (06:39 +0000)]
net: macb: Added PCI wrapper for Platform Driver.
There are hardware PCI implementations of Cadence GEM network
controller. This patch will allow to use such hardware with reuse of
existing Platform Driver.
Signed-off-by: Bartosz Folta <bfolta@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Wed, 14 Dec 2016 00:15:09 +0000 (18:15 -0600)]
ibmveth: calculate gso_segs for large packets
Include calculations to compute the number of segments
that comprise an aggregated large packet.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jonathan Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi [Tue, 13 Dec 2016 23:49:02 +0000 (17:49 -0600)]
net: qcom/emac: don't try to claim clocks on ACPI systems
On ACPI systems, clocks are not available to drivers directly. They are
handled exclusively by ACPI and/or firmware, so there is no clock driver.
Calls to clk_get() always fail, so we should not even attempt to claim
any clocks on ACPI systems.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro [Fri, 16 Dec 2016 21:34:52 +0000 (16:34 -0500)]
Merge branch 'work.autofs' into for-linus
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Fri, 16 Dec 2016 21:21:05 +0000 (16:21 -0500)]
Merge remote-tracking branch 'djwong/ocfs2-vfs-reflink-6' into for-linus
Al Viro [Fri, 16 Dec 2016 21:19:49 +0000 (16:19 -0500)]
Merge branch 'work.write_end' into for-linus
Chris Metcalf [Mon, 7 Nov 2016 19:19:10 +0000 (14:19 -0500)]
tile: use __ro_after_init instead of tile-specific __write_once
The semantics of the old tile __write_once are the same as the
newer generic __ro_after_init, so rename them all and get rid
of the tile-specific version.
This does not enable actual support for __ro_after_init,
which had been dropped from the tile architecture before the
initial upstreaming was done, since we had at that time switched
to using 16MB huge pages to map the kernel.
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Paul Gortmaker [Mon, 19 Sep 2016 21:34:39 +0000 (17:34 -0400)]
tile: migrate exception table users off module.h and onto extable.h
These files were only including module.h for exception table
related functions. We've now separated that content out into its
own file "extable.h" so now move over to that and avoid all the
extra header content in module.h that we don't really need to compile
these files.
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Chris Metcalf [Tue, 6 Sep 2016 19:56:15 +0000 (15:56 -0400)]
tile: remove #pragma unroll from finv_buffer_remote()
This directive was put in the kernel source before the "pragma
unroll" support for tilegx gcc was upstreamed. Remove it for
now, and we can put it back later if/when the compiler support
is upstreamed. This avoids a warning when building the kernel.
This routine is not on a hot path in any case, so the extra
optimization here was mostly just for its own sake.
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Markus Elfring [Sat, 3 Sep 2016 18:45:20 +0000 (20:45 +0200)]
tile-module: Rename jump labels in module_alloc()
Adjust jump labels according to the current Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Markus Elfring [Sat, 3 Sep 2016 18:40:57 +0000 (20:40 +0200)]
tile-module: Use kmalloc_array() in module_alloc()
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
* Replace the specification of a data type by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Colin Ian King [Thu, 18 Aug 2016 15:42:01 +0000 (16:42 +0100)]
tile/pci_gx: fix spelling mistake: "delievered" -> "delivered"
trivial fix to spelling mistake in pr_warn message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Linus Torvalds [Fri, 16 Dec 2016 19:23:34 +0000 (11:23 -0800)]
Merge tag 'ceph-for-4.10-rc1' of git://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"A varied set of changes:
- a large rework of cephx auth code to cope with CONFIG_VMAP_STACK
(myself). Also fixed a deadlock caused by a bogus allocation on the
writeback path and authorize reply verification.
- a fix for long stalls during fsync (Jeff Layton). The client now
has a way to force the MDS log flush, leading to ~100x speedups in
some synthetic tests.
- a new [no]require_active_mds mount option (Zheng Yan).
On mount, we will now check whether any of the MDSes are available
and bail rather than block if none are. This check can be avoided
by specifying the "no" option.
- a couple of MDS cap handling fixes and a few assorted patches
throughout"
* tag 'ceph-for-4.10-rc1' of git://github.com/ceph/ceph-client: (32 commits)
libceph: remove now unused finish_request() wrapper
libceph: always signal completion when done
ceph: avoid creating orphan object when checking pool permission
ceph: properly set issue_seq for cap release
ceph: add flags parameter to send_cap_msg
ceph: update cap message struct version to 10
ceph: define new argument structure for send_cap_msg
ceph: move xattr initialzation before the encoding past the ceph_mds_caps
ceph: fix minor typo in unsafe_request_wait
ceph: record truncate size/seq for snap data writeback
ceph: check availability of mds cluster on mount
ceph: fix splice read for no Fc capability case
ceph: try getting buffer capability for readahead/fadvise
ceph: fix scheduler warning due to nested blocking
ceph: fix printing wrong return variable in ceph_direct_read_write()
crush: include mapper.h in mapper.c
rbd: silence bogus -Wmaybe-uninitialized warning
libceph: no need to drop con->mutex for ->get_authorizer()
libceph: drop len argument of *verify_authorizer_reply()
libceph: verify authorize reply on connect
...
Linus Torvalds [Fri, 16 Dec 2016 18:58:12 +0000 (10:58 -0800)]
Merge branch 'overlayfs-linus' of git://git./linux/kernel/git/mszeredi/vfs
Pull overlayfs updates from Miklos Szeredi:
"This update contains:
- try to clone on copy-up
- allow renaming a directory
- split source into managable chunks
- misc cleanups and fixes
It does not contain the read-only fd data inconsistency fix, which Al
didn't like. I'll leave that to the next year..."
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs: (36 commits)
ovl: fix reStructuredText syntax errors in documentation
ovl: fix return value of ovl_fill_super
ovl: clean up kstat usage
ovl: fold ovl_copy_up_truncate() into ovl_copy_up()
ovl: create directories inside merged parent opaque
ovl: opaque cleanup
ovl: show redirect_dir mount option
ovl: allow setting max size of redirect
ovl: allow redirect_dir to default to "on"
ovl: check for emptiness of redirect dir
ovl: redirect on rename-dir
ovl: lookup redirects
ovl: consolidate lookup for underlying layers
ovl: fix nested overlayfs mount
ovl: check namelen
ovl: split super.c
ovl: use d_is_dir()
ovl: simplify lookup
ovl: check lower existence of rename target
ovl: rename: simplify handling of lower/merged directory
...
Linus Torvalds [Fri, 16 Dec 2016 18:53:01 +0000 (10:53 -0800)]
Merge branch 'for-linus-4.10' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs updates from Chris Mason:
"Jeff Mahoney and Dave Sterba have a really nice set of cleanups in
here, and Christoph pitched in corrections/improvements to make btrfs
use proper helpers for bio walking instead of doing it by hand.
There are some key fixes as well, including some long standing bugs
that took forever to track down in btrfs_drop_extents and during
balance"
* 'for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (77 commits)
btrfs: limit async_work allocation and worker func duration
Revert "Btrfs: adjust len of writes if following a preallocated extent"
Btrfs: don't WARN() in btrfs_transaction_abort() for IO errors
btrfs: opencode chunk locking, remove helpers
btrfs: remove root parameter from transaction commit/end routines
btrfs: split btrfs_wait_marked_extents into normal and tree log functions
btrfs: take an fs_info directly when the root is not used otherwise
btrfs: simplify btrfs_wait_cache_io prototype
btrfs: convert extent-tree tracepoints to use fs_info
btrfs: root->fs_info cleanup, access fs_info->delayed_root directly
btrfs: root->fs_info cleanup, add fs_info convenience variables
btrfs: root->fs_info cleanup, update_block_group{,flags}
btrfs: root->fs_info cleanup, lock/unlock_chunks
btrfs: root->fs_info cleanup, btrfs_calc_{trans,trunc}_metadata_size
btrfs: pull node/sector/stripe sizes out of root and into fs_info
btrfs: root->fs_info cleanup, io_ctl_init
btrfs: root->fs_info cleanup, use fs_info->dev_root everywhere
btrfs: struct reada_control.root -> reada_control.fs_info
btrfs: struct btrfsic_state->root should be an fs_info
btrfs: alloc_reserved_file_extent trace point should use extent_root
...
Linus Torvalds [Fri, 16 Dec 2016 18:48:28 +0000 (10:48 -0800)]
Merge tag 'nfsd-4.10' of git://linux-nfs.org/~bfields/linux
Pull nfsd updates from Bruce Fields:
"The one new feature is support for a new NFSv4.2 mode_umask attribute
that makes ACL inheritance a little more useful in environments that
default to restrictive umasks. Requires client-side support, also on
its way for 4.10.
Other than that, miscellaneous smaller fixes and cleanup, especially
to the server rdma code"
[ The client side of the umask attribute was merged yesterday ]
* tag 'nfsd-4.10' of git://linux-nfs.org/~bfields/linux:
nfsd: add support for the umask attribute
sunrpc: use DEFINE_SPINLOCK()
svcrdma: Further clean-up of svc_rdma_get_inv_rkey()
svcrdma: Break up dprintk format in svc_rdma_accept()
svcrdma: Remove unused variable in rdma_copy_tail()
svcrdma: Remove unused variables in xprt_rdma_bc_allocate()
svcrdma: Remove svc_rdma_op_ctxt::wc_status
svcrdma: Remove DMA map accounting
svcrdma: Remove BH-disabled spin locking in svc_rdma_send()
svcrdma: Renovate sendto chunk list parsing
svcauth_gss: Close connection when dropping an incoming message
svcrdma: Clear xpt_bc_xps in xprt_setup_rdma_bc() error exit arm
nfsd: constify reply_cache_stats_operations structure
nfsd: update workqueue creation
sunrpc: GFP_KERNEL should be GFP_NOFS in crypto code
nfsd: catch errors in decode_fattr earlier
nfsd: clean up supported attribute handling
nfsd: fix error handling for clients that fail to return the layout
nfsd: more robust allocation failure handling in nfsd_reply_cache_init
Jeroen De Wachter [Mon, 12 Dec 2016 13:29:09 +0000 (14:29 +0100)]
encx24j600: Fix some checkstyle warnings
Signed-off-by: Jeroen De Wachter <jeroen.de_wachter.ext@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeroen De Wachter [Mon, 12 Dec 2016 13:29:08 +0000 (14:29 +0100)]
encx24j600: bugfix - always move ERXTAIL to next packet in encx24j600_rx_packets
Before, encx24j600_rx_packets did not update encx24j600_priv's next_packet
member when an error occurred during packet handling (either because the
packet's RSV header indicates an error or because the encx24j600_receive_packet
method can't allocate an sk_buff).
If the next_packet member is not updated, the ERXTAIL register will be set to
the same value it had before, which means the bad packet remains in the
component's memory and its RSV header will be read again when a new packet
arrives. If the RSV header indicates a bad packet or if sk_buff allocation
continues to fail, new packets will be stored in the component's memory until
that memory is full, after which packets will be dropped.
The SETPKTDEC command is always executed though, so the encx24j600 hardware has
an incorrect count of the packets in its memory.
To prevent this, the next_packet member should always be updated, allowing the
packet to be skipped (either because it's bad, as indicated in its RSV header,
or because allocating an sk_buff failed). In the allocation failure case, this
does mean dropping a valid packet, but dropping the oldest packet to keep as
much memory as possible available for new packets seems preferable to keeping
old (but valid) packets around while dropping new ones.
Signed-off-by: Jeroen De Wachter <jeroen.de_wachter.ext@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 16 Dec 2016 18:29:42 +0000 (13:29 -0500)]
Merge branch 'hisilicon-netdev-dev'
Dongpo Li says:
====================
net: ethernet: hisilicon: set dev->dev.parent before PHY connect
This patch series builds atop:
ec988ad78ed6d184a7f4ca6b8e962b0e8f1de461 ("phy: Don't increment MDIO bus
refcount unless it's a different owner")
I have checked all the hisilicon ethernet driver and found only two drivers
need to be fixed to make sure set dev->dev.parent before PHY connect.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dongpo Li [Mon, 12 Dec 2016 12:03:43 +0000 (20:03 +0800)]
net: ethernet: hip04: Call SET_NETDEV_DEV()
The hip04 driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.
Fixes: ec988ad78ed6 ("phy: Don't increment MDIO bus refcount unless it's a different owner")
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dongpo Li [Mon, 12 Dec 2016 12:03:42 +0000 (20:03 +0800)]
net: ethernet: hisi_femac: Call SET_NETDEV_DEV()
The hisi_femac driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.
Fixes: ec988ad78ed6 ("phy: Don't increment MDIO bus refcount unless it's a different owner")
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 11 Dec 2016 20:07:19 +0000 (21:07 +0100)]
net: dsa: mv88e6xxx: Fix opps when adding vlan bridge
A port is not necessarily assigned to a netdev. And a port does not
need to be a member of a bridge. So when iterating over all ports,
check before using the netdev and bridge_dev for a port. Otherwise we
dereference a NULL pointer.
Fixes: da9c359e19f0 ("net: dsa: mv88e6xxx: check hardware VLAN in use")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Gleixner [Sun, 11 Dec 2016 17:31:22 +0000 (18:31 +0100)]
net/3com/3c515: Fix timer handling, prevent leaks and crashes
The timer handling in this driver is broken in several ways:
- corkscrew_open() initializes and arms a timer before requesting the
device interrupt. If the request fails the timer stays armed.
A second call to corkscrew_open will unconditionally reinitialize the
quued timer and arm it again. Also a immediate device removal will leave
the timer queued because close() is not called (open() failed) and
therefore nothing issues del_timer().
The reinitialization corrupts the link chain in the timer wheel hash
bucket and causes a NULL pointer dereference when the timer wheel tries
to operate on that hash bucket. Immediate device removal lets the link
chain poke into freed and possibly reused memory.
Solution: Arm the timer after the successful irq request.
- corkscrew_close() uses del_timer()
On close the timer is disarmed with del_timer() which lets the following
code race against a concurrent timer expiry function.
Solution: Use del_timer_sync() instead
- corkscrew_close() calls del_timer() unconditionally
del_timer() is invoked even if the timer was never initialized. This
works by chance because the struct containing the timer is zeroed at
allocation time.
Solution: Move the setup of the timer into corkscrew_setup().
Reported-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 16 Dec 2016 18:24:44 +0000 (10:24 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull vfs updates from Al Viro:
- more ->d_init() stuff (work.dcache)
- pathname resolution cleanups (work.namei)
- a few missing iov_iter primitives - copy_from_iter_full() and
friends. Either copy the full requested amount, advance the iterator
and return true, or fail, return false and do _not_ advance the
iterator. Quite a few open-coded callers converted (and became more
readable and harder to fuck up that way) (work.iov_iter)
- several assorted patches, the big one being logfs removal
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
logfs: remove from tree
vfs: fix put_compat_statfs64() does not handle errors
namei: fold should_follow_link() with the step into not-followed link
namei: pass both WALK_GET and WALK_MORE to should_follow_link()
namei: invert WALK_PUT logics
namei: shift interpretation of LOOKUP_FOLLOW inside should_follow_link()
namei: saner calling conventions for mountpoint_last()
namei.c: get rid of user_path_parent()
switch getfrag callbacks to ..._full() primitives
make skb_add_data,{_nocache}() and skb_copy_to_page_nocache() advance only on success
[iov_iter] new primitives - copy_from_iter_full() and friends
don't open-code file_inode()
ceph: switch to use of ->d_init()
ceph: unify dentry_operations instances
lustre: switch to use of ->d_init()
Linus Torvalds [Fri, 16 Dec 2016 17:39:16 +0000 (09:39 -0800)]
Merge tag 'media/v4.10-1' of git://git./linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new Mediatek drivers: mtk-mdp and mtk-vcodec
- some additions at the media documentation
- the CEC core and drivers were promoted from staging to mainstream
- some cleanups at the DVB core
- the LIRC serial driver got promoted from staging to mainstream
- added a driver for Renesas R-Car FDP1 driver
- add DVBv5 statistics support to mn88473 driver
- several fixes related to printk continuation lines
- add support for HSV encoding formats
- lots of other cleanups, fixups and driver improvements.
* tag 'media/v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (496 commits)
[media] v4l: tvp5150: Add missing break in set control handler
[media] v4l: tvp5150: Don't inline the tvp5150_selmux() function
[media] v4l: tvp5150: Compile tvp5150_link_setup out if !CONFIG_MEDIA_CONTROLLER
[media] em28xx: don't store usb_device at struct em28xx
[media] em28xx: use usb_interface for dev_foo() calls
[media] em28xx: don't change the device's name
[media] mn88472: fix chip id check on probe
[media] mn88473: fix chip id check on probe
[media] lirc: fix error paths in lirc_cdev_add()
[media] s5p-mfc: Add support for MFC v8 available in Exynos 5433 SoCs
[media] s5p-mfc: Rework clock handling
[media] s5p-mfc: Don't keep clock prepared all the time
[media] s5p-mfc: Kill all IS_ERR_OR_NULL in clocks management code
[media] s5p-mfc: Remove dead conditional code
[media] s5p-mfc: Ensure that clock is disabled before turning power off
[media] s5p-mfc: Remove special clock rate management
[media] s5p-mfc: Use printk_ratelimited for reporting ioctl errors
[media] s5p-mfc: Set DMA_ATTR_ALLOC_SINGLE_PAGES
[media] vivid: Set color_enc on HSV formats
[media] v4l2-tpg: Init hv_enc field with a valid value
...
projects / platform / kernel / linux-starfive.git / log