wifi: mwifiex: add extra delay for firmware ready

commit 1c5d463c0770c6fa2037511a24fb17966fd07d97 upstream.

For SDIO IW416, due to a bug, FW may return ready before complete full
initialization. Command timeout may occur at driver load after reboot.
Workaround by adding 100ms delay at checking FW status.

Signed-off-by: David Lin <yu-hao.lin@nxp.com>
Cc: stable@vger.kernel.org
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # Verdin AM62 (IW416)
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231208234029.2197-1-yu-hao.lin@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wifi: rtlwifi: Convert LNKCTL change to PCIe cap RMW accessors

commit 5894d0089cbc146063dcc0239a78ede0a8142efb upstream.

The rtlwifi driver comes with custom code to write into PCIe Link
Control register. RMW access for the Link Control register requires
locking that is already provided by the standard PCIe capability
accessors.

Convert the custom RMW code writing into LNKCTL register to standard
RMW capability accessors. The accesses are changed to cover the full
LNKCTL register instead of touching just a single byte of the register.

Fixes: 0c8173385e54 ("rtl8192ce: Add new driver")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124084725.12738-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wifi: rtlwifi: Remove bogus and dangerous ASPM disable/enable code

commit b3943b3c2971444364e03224cfc828c5789deada upstream.

Ever since introduction in the commit 0c8173385e54 ("rtl8192ce: Add new
driver") the rtlwifi code has, according to comments, attempted to
disable/enable ASPM of the upstream bridge by writing into its LNKCTL
register. However, the code has never been correct because it performs
the writes to the device instead of the upstream bridge.

Worse yet, the offset where the PCIe capabilities reside is derived
from the offset of the upstream bridge. As a result, the write will use
an offset on the device that does not relate to the LNKCTL register
making the ASPM disable/enable code outright dangerous.

Because of those problems, there is no indication that the driver needs
disable/enable ASPM on the upstream bridge. As the Capabilities offset
is not correctly calculated for the write to target device's LNKCTL
register, the code is not disabling/enabling device's ASPM either.
Therefore, just remove the upstream bridge related ASPM disable/enable
code entirely.

The upstream bridge related ASPM code was the only user of the struct
mp_adapter members num4bytes, pcibridge_pciehdr_offset, and
pcibridge_linkctrlreg so those are removed as well.

Note: This change does not remove the code related to changing the
device's ASPM on purpose (which is independent of this flawed code
related to upstream bridge's ASPM).

Suggested-by: Bjorn Helgaas <bhelgaas@kernel.org>
Fixes: 0c8173385e54 ("rtl8192ce: Add new driver")
Fixes: 886e14b65a8f ("rtlwifi: Eliminate raw reads and writes from PCIe portion")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124084725.12738-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wifi: mt76: fix broken precal loading from MTD for mt7915

commit e874a79250b39447765ac13272b67ac36ccf2a75 upstream.

Commit 495184ac91bb ("mt76: mt7915: add support for applying
pre-calibration data") was fundamentally broken and never worked.

The idea (before NVMEM support) was to expand the MTD function and pass
an additional offset. For normal EEPROM load the offset would always be
0. For the purpose of precal loading, an offset was passed that was
internally the size of EEPROM, since precal data is right after the
EEPROM.

Problem is that the offset value passed is never handled and is actually
overwrite by

offset = be32_to_cpup(list);
ret = mtd_read(mtd, offset, len, &retlen, eep);

resulting in the passed offset value always ingnored. (and even passing
garbage data as precal as the start of the EEPROM is getting read)

Fix this by adding to the current offset value, the offset from DT to
correctly read the piece of data at the requested location.

Cc: stable@vger.kernel.org
Fixes: 495184ac91bb ("mt76: mt7915: add support for applying pre-calibration data")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu/dma: Trace bounce buffer usage when mapping buffers

commit a63c357b9fd56ad5fe64616f5b22835252c6a76a upstream.

When commit 82612d66d51d ("iommu: Allow the dma-iommu api to
use bounce buffers") was introduced, it did not add the logic
for tracing the bounce buffer usage from iommu_dma_map_page().

All of the users of swiotlb_tbl_map_single() trace their bounce
buffer usage, except iommu_dma_map_page(). This makes it difficult
to track SWIOTLB usage from that function. Thus, trace bounce buffer
usage from iommu_dma_map_page().

Fixes: 82612d66d51d ("iommu: Allow the dma-iommu api to use bounce buffers")
Cc: stable@vger.kernel.org # v5.15+
Cc: Tom Murphy <murphyt7@tcd.ie>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Saravana Kannan <saravanak@google.com>
Signed-off-by: Isaac J. Manjarres <isaacmanjarres@google.com>
Link: https://lore.kernel.org/r/20231208234141.2356157-1-isaacmanjarres@google.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu/arm-smmu-qcom: Add missing GMU entry to match table

commit afc95681c3068956fed1241a1ff1612c066c75ac upstream.

In some cases the firmware expects cbndx 1 to be assigned to the GMU,
so we also want the default domain for the GMU to be an identy domain.
This way it does not get a context bank assigned.  Without this, both
of_dma_configure() and drm/msm's iommu_domain_attach() will trigger
allocating and configuring a context bank.  So GMU ends up attached to
both cbndx 1 and later cbndx 2.  This arrangement seemingly confounds
and surprises the firmware if the GPU later triggers a translation
fault, resulting (on sc8280xp / lenovo x13s, at least) in the SMMU
getting wedged and the GPU stuck without memory access.

Cc: stable@vger.kernel.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20231210180655.75542-1-robdclark@gmail.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bpf: Fix re-attachment branch in bpf_tracing_prog_attach

commit 715d82ba636cb3629a6e18a33bb9dbe53f9936ee upstream.

The following case can cause a crash due to missing attach_btf:

1) load rawtp program
2) load fentry program with rawtp as target_fd
3) create tracing link for fentry program with target_fd = 0
4) repeat 3

In the end we have:

- prog->aux->dst_trampoline == NULL
- tgt_prog == NULL (because we did not provide target_fd to link_create)
- prog->aux->attach_btf == NULL (the program was loaded with attach_prog_fd=X)
- the program was loaded for tgt_prog but we have no way to find out which one

    BUG: kernel NULL pointer dereference, address: 0000000000000058
    Call Trace:
     <TASK>
     ? __die+0x20/0x70
     ? page_fault_oops+0x15b/0x430
     ? fixup_exception+0x22/0x330
     ? exc_page_fault+0x6f/0x170
     ? asm_exc_page_fault+0x22/0x30
     ? bpf_tracing_prog_attach+0x279/0x560
     ? btf_obj_id+0x5/0x10
     bpf_tracing_prog_attach+0x439/0x560
     __sys_bpf+0x1cf4/0x2de0
     __x64_sys_bpf+0x1c/0x30
     do_syscall_64+0x41/0xf0
     entry_SYSCALL_64_after_hwframe+0x6e/0x76

Return -EINVAL in this situation.

Fixes: f3a95075549e0 ("bpf: Allow trampoline re-attach for tracing and lsm programs")
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Olsa <olsajiri@gmail.com>
Acked-by: Jiri Olsa <olsajiri@gmail.com>
Acked-by: Song Liu <song@kernel.org>
Signed-off-by: Dmitrii Dolgov <9erthalion6@gmail.com>
Link: https://lore.kernel.org/r/20240103190559.14750-4-9erthalion6@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: Fix atomicity violation in {min,max}_key_size_set

commit da9065caa594d19b26e1a030fd0cc27bd365d685 upstream.

In min_key_size_set():
    if (val > hdev->le_max_key_size || val < SMP_MIN_ENC_KEY_SIZE)
        return -EINVAL;
    hci_dev_lock(hdev);
    hdev->le_min_key_size = val;
    hci_dev_unlock(hdev);

In max_key_size_set():
    if (val > SMP_MAX_ENC_KEY_SIZE || val < hdev->le_min_key_size)
        return -EINVAL;
    hci_dev_lock(hdev);
    hdev->le_max_key_size = val;
    hci_dev_unlock(hdev);

The atomicity violation occurs due to concurrent execution of set_min and
set_max funcs.Consider a scenario where setmin writes a new, valid 'min'
value, and concurrently, setmax writes a value that is greater than the
old 'min' but smaller than the new 'min'. In this case, setmax might check
against the old 'min' value (before acquiring the lock) but write its
value after the 'min' has been updated by setmin. This leads to a
situation where the 'max' value ends up being smaller than the 'min'
value, which is an inconsistency.

This possible bug is found by an experimental static analysis tool
developed by our team, BassCheck[1]. This tool analyzes the locking APIs
to extract function pairs that can be concurrently executed, and then
analyzes the instructions in the paired functions to identify possible
concurrency bugs including data races and atomicity violations. The above
possible bug is reported when our tool analyzes the source code of
Linux 5.17.

To resolve this issue, it is suggested to encompass the validity checks
within the locked sections in both set_min and set_max funcs. The
modification ensures that the validation of 'val' against the
current min/max values is atomic, thus maintaining the integrity of the
settings. With this patch applied, our tool no longer reports the bug,
with the kernel configuration allyesconfig for x86_64. Due to the lack of
associated hardware, we cannot test the patch in runtime testing, and just
verify it according to the code logic.

[1] https://sites.google.com/view/basscheck/

Fixes: 18f81241b74f ("Bluetooth: Move {min,max}_key_size debugfs ...")
Cc: stable@vger.kernel.org
Signed-off-by: Gui-Dong Han <2045gemini@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rootfs: Fix support for rootfstype= when root= is given

commit 21528c69a0d8483f7c6345b1a0bc8d8975e9a172 upstream.

Documentation/filesystems/ramfs-rootfs-initramfs.rst states:

  If CONFIG_TMPFS is enabled, rootfs will use tmpfs instead of ramfs by
  default.  To force ramfs, add "rootfstype=ramfs" to the kernel command
  line.

This currently does not work when root= is provided since then
saved_root_name contains a string and rootfstype= is ignored. Therefore,
ramfs is currently always chosen when root= is provided.

The current behavior for rootfs's filesystem is:

   root=       | rootfstype= | chosen rootfs filesystem
   ------------+-------------+--------------------------
   unspecified | unspecified | tmpfs
   unspecified | tmpfs       | tmpfs
   unspecified | ramfs       | ramfs
    provided   | ignored     | ramfs

rootfstype= should be respected regardless whether root= is given,
as shown below:

   root=       | rootfstype= | chosen rootfs filesystem
   ------------+-------------+--------------------------
   unspecified | unspecified | tmpfs  (as before)
   unspecified | tmpfs       | tmpfs  (as before)
   unspecified | ramfs       | ramfs  (as before)
    provided   | unspecified | ramfs  (compatibility with before)
    provided   | tmpfs       | tmpfs  (new)
    provided   | ramfs       | ramfs  (new)

This table represents the new behavior.

Fixes: 6e19eded3684 ("initmpfs: use initramfs if rootfstype= or root= specified")
Cc: <stable@vger.kernel.org>
Signed-off-by: Rob Landley <rob@landley.net>
Link: https://lore.kernel.org/lkml/8244c75f-445e-b15b-9dbf-266e7ca666e2@landley.net/
Reviewed-and-Tested-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Link: https://lore.kernel.org/r/20231120011248.396012-1-stefanb@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md/raid1: Use blk_opf_t for read and write operations

commit 7dab24554dedd4e6f408af8eb2d25c89997a6a1f upstream.

Use the type blk_opf_t for read and write operations instead of int. This
patch does not affect the generated code but fixes the following sparse
warning:

drivers/md/raid1.c:1993:60: sparse: sparse: incorrect type in argument 5 (different base types)
     expected restricted blk_opf_t [usertype] opf
     got int rw

Cc: Song Liu <song@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Fixes: 3c5e514db58f ("md/raid1: Use the new blk_opf_t type")
Cc: stable@vger.kernel.org # v6.0+
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401080657.UjFnvQgX-lkp@intel.com/
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240108001223.23835-1-bvanassche@acm.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pwm: Fix out-of-bounds access in of_pwm_single_xlate()

commit a297d07b9a1e4fb8cda25a4a2363a507d294b7c9 upstream.

With args->args_count == 2 args->args[2] is not defined. Actually the
flags are contained in args->args[1].

Fixes: 3ab7b6ac5d82 ("pwm: Introduce single-PWM of_xlate function")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/243908750d306e018a3d4bf2eb745d53ab50f663.1704835845.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pwm: jz4740: Don't use dev_err_probe() in .request()

commit 9320fc509b87b4d795fb37112931e2f4f8b5c55f upstream.

dev_err_probe() is only supposed to be used in probe functions. While it
probably doesn't hurt, both the EPROBE_DEFER handling and calling
device_set_deferred_probe_reason() are conceptually wrong in the request
callback. So replace the call by dev_err() and a separate return
statement.

This effectively reverts commit c0bfe9606e03 ("pwm: jz4740: Simplify
with dev_err_probe()").

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240106141302.1253365-2-u.kleine-koenig@pengutronix.de
Fixes: c0bfe9606e03 ("pwm: jz4740: Simplify with dev_err_probe()")
Cc: stable@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: nf_tables: check if catch-all set element is active in next generation

commit b1db244ffd041a49ecc9618e8feb6b5c1afcdaa7 upstream.

When deactivating the catch-all set element, check the state in the next
generation that represents this transaction.

This bug uncovered after the recent removal of the element busy mark
a2dd0233cbc4 ("netfilter: nf_tables: remove busy mark and gc batch API").

Fixes: aaa31047a6d2 ("netfilter: nftables: add catch-all set element support")
Cc: stable@vger.kernel.org
Reported-by: lonial con <kongln9170@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block: Fix iterating over an empty bio with bio_for_each_folio_all

commit 7bed6f3d08b7af27b7015da8dc3acf2b9c1f21d7 upstream.

If the bio contains no data, bio_first_folio() calls page_folio() on a
NULL pointer and oopses.  Move the test that we've reached the end of
the bio from bio_next_folio() to bio_first_folio().

Reported-by: syzbot+8b23309d5788a79d3eea@syzkaller.appspotmail.com
Reported-by: syzbot+004c1e0fced2b4bc3dcc@syzkaller.appspotmail.com
Fixes: 640d1930bef4 ("block: Add bio_for_each_folio_all()")
Cc: stable@vger.kernel.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Link: https://lore.kernel.org/r/20240116212959.3413014-1-willy@infradead.org
[axboe: add unlikely() to error case]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block: Remove special-casing of compound pages

commit 1b151e2435fc3a9b10c8946c6aebe9f3e1938c55 upstream.

The special casing was originally added in pre-git history; reproducing
the commit log here:

> commit a318a92567d77
> Author: Andrew Morton <akpm@osdl.org>
> Date:   Sun Sep 21 01:42:22 2003 -0700
>
>     [PATCH] Speed up direct-io hugetlbpage handling
>
>     This patch short-circuits all the direct-io page dirtying logic for
>     higher-order pages.  Without this, we pointlessly bounce BIOs up to
>     keventd all the time.

In the last twenty years, compound pages have become used for more than
just hugetlb.  Rewrite these functions to operate on folios instead
of pages and remove the special case for hugetlbfs; I don't think
it's needed any more (and if it is, we can put it back in as a call
to folio_test_hugetlb()).

This was found by inspection; as far as I can tell, this bug can lead
to pages used as the destination of a direct I/O read not being marked
as dirty.  If those pages are then reclaimed by the MM without being
dirtied for some other reason, they won't be written out.  Then when
they're faulted back in, they will not contain the data they should.
It'll take a pretty unusual setup to produce this problem with several
races all going the wrong way.

This problem predates the folio work; it could for example have been
triggered by mmaping a THP in tmpfs and using that as the target of an
O_DIRECT read.

Fixes: 800d8c63b2e98 ("shmem: add huge pages support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block: add check that partition length needs to be aligned with block size

commit 6f64f866aa1ae6975c95d805ed51d7e9433a0016 upstream.

Before calling add partition or resize partition, there is no check
on whether the length is aligned with the logical block size.
If the logical block size of the disk is larger than 512 bytes,
then the partition size maybe not the multiple of the logical block size,
and when the last sector is read, bio_truncate() will adjust the bio size,
resulting in an IO error if the size of the read command is smaller than
the logical block size.If integrity data is supported, this will also
result in a null pointer dereference when calling bio_integrity_free.

Cc: <stable@vger.kernel.org>
Signed-off-by: Min Li <min15.li@samsung.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230629142517.121241-1-min15.li@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amd: Enable PCIe PME from D3

commit bd1f6a31e7762ebc99b97f3eda5e5ea3708fa792 upstream.

When dGPU is put into BOCO it may be in D3cold but still able send
PME on display hotplug event. For this to work it must be enabled
as wake source from D3.

When runpm is enabled use pci_wake_from_d3() to mark wakeup as
enabled by default.

Cc: stable@vger.kernel.org # 6.1+
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: mpi3mr: Block PEL Enable Command on Controller Reset and Unrecoverable State

commit f8fb3f39148e8010479e4b2003ba4728818ec661 upstream.

If a controller reset is underway or the controller is in an unrecoverable
state, the PEL enable management command will be returned as EAGAIN or
EFAULT.

Cc: <stable@vger.kernel.org> # v6.1+
Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Chandrakanth patil <chandrakanth.patil@broadcom.com>
Link: https://lore.kernel.org/r/20231126053134.10133-4-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: mpi3mr: Clean up block devices post controller reset

commit c01d515687e358b22aa8414d6dac60d7defa6eb9 upstream.

After a controller reset, if the firmware changes the state of devices to
"hide", then remove those devices from the OS.

Cc: <stable@vger.kernel.org> # v6.6+
Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Chandrakanth patil <chandrakanth.patil@broadcom.com>
Link: https://lore.kernel.org/r/20231126053134.10133-3-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: mpi3mr: Refresh sdev queue depth after controller reset

commit e5aab848dfdf7996d20ece4d28d2733c732c5e5a upstream.

After a controller reset, the firmware may modify the device queue depth.
Therefore, update the device queue depth accordingly.

Cc: <stable@vger.kernel.org> # v5.15+
Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Chandrakanth patil <chandrakanth.patil@broadcom.com>
Link: https://lore.kernel.org/r/20231126053134.10133-2-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: target: core: add missing file_{start,end}_write()

commit 0db1d53937fafa8bb96e077375691e16902f4899 upstream.

The callers of vfs_iter_write() are required to hold file_start_write().
file_start_write() is a no-op for the S_ISBLK() case, but it is really
needed when the backing file is a regular file.

We are going to move file_{start,end}_write() into vfs_iter_write(), but
we need to fix this first, so that the fix could be backported to stable
kernels.

Suggested-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/ZV8ETIpM+wZa33B5@infradead.org/
Cc: <stable@vger.kernel.org>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Link: https://lore.kernel.org/r/20231123092000.2665902-1-amir73il@gmail.com
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: ufs: core: Simplify power management during async scan

commit daf7795406bf307997366f694888bd317ae5b5fa upstream.

ufshcd_init() calls pm_runtime_get_sync() before it calls
async_schedule(). ufshcd_async_scan() calls pm_runtime_put_sync() directly
or indirectly from ufshcd_add_lus(). Simplify ufshcd_async_scan() by always
calling pm_runtime_put_sync() from ufshcd_async_scan().

Cc: <stable@vger.kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20231218225229.2542156-2-bvanassche@acm.org
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fbdev: flush deferred IO before closing

commit 33cd6ea9c0673517cdb06ad5c915c6f22e9615fc upstream.

When framebuffer gets closed, the queued deferred IO gets cancelled. This
can cause some last display data to vanish. This is problematic for users
who send a still image to the framebuffer, then close the file: the image
may never appear.

To ensure none of display data get lost, flush the queued deferred IO
first before closing.

Another possible solution is to delete the cancel_delayed_work_sync()
instead. The difference is that the display may appear some time after
closing. However, the clearing of page mapping after this needs to be
removed too, because the page mapping is used by the deferred work. It is
not completely obvious whether it is okay to not clear the page mapping.
For a patch intended for stable trees, go with the simple and obvious
solution.

Fixes: 60b59beafba8 ("fbdev: mm: Deferred IO support")
Cc: stable@vger.kernel.org
Signed-off-by: Nam Cao <namcao@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fbdev: flush deferred work in fb_deferred_io_fsync()

commit 15e4c1f462279b4e128f27de48133e0debe9e0df upstream.

The driver's fsync() is supposed to flush any pending operation to
hardware. It is implemented in this driver by cancelling the queued
deferred IO first, then schedule it for "immediate execution" by calling
schedule_delayed_work() again with delay=0. However, setting delay=0
only means the work is scheduled immediately, it does not mean the work
is executed immediately. There is no guarantee that the work is finished
after schedule_delayed_work() returns. After this driver's fsync()
returns, there can still be pending work. Furthermore, if close() is
called by users immediately after fsync(), the pending work gets
cancelled and fsync() may do nothing.

To ensure that the deferred IO completes, use flush_delayed_work()
instead. Write operations to this driver either write to the device
directly, or invoke schedule_delayed_work(); so by flushing the
workqueue, it can be guaranteed that all previous writes make it to the
device.

Fixes: 5e841b88d23d ("fb: fsync() method for deferred I/O flush.")
Cc: stable@vger.kernel.org
Signed-off-by: Nam Cao <namcao@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fbdev/acornfb: Fix name of fb_ops initializer macro

commit b48807788e7a2bd93044fe84cfe8ff64b85ec15e upstream.

Fix build by using the correct name for the initializer macro
for struct fb_ops.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 9037afde8b9d ("fbdev/acornfb: Use fbdev I/O helpers")
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: <stable@vger.kernel.org> # v6.6+
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231127131655.4020-2-tzimmermann@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

io_uring: ensure local task_work is run on wait timeout

commit 6ff1407e24e6fdfa4a16ba9ba551e3d253a26391 upstream.

A previous commit added an earlier break condition here, which is fine if
we're using non-local task_work as it'll be run on return to userspace.
However, if DEFER_TASKRUN is used, then we could be leaving local
task_work that is ready to process in the ctx list until next time that
we enter the kernel to wait for events.

Move the break condition to _after_ we have run task_work.

Cc: stable@vger.kernel.org
Fixes: 846072f16eed ("io_uring: mimimise io_cqring_wait_schedule")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

io_uring/rw: ensure io->bytes_done is always initialized

commit 0a535eddbe0dc1de4386046ab849f08aeb2f8faf upstream.

If IOSQE_ASYNC is set and we fail importing an iovec for a readv or
writev request, then we leave ->bytes_done uninitialized and hence the
eventual failure CQE posted can potentially have a random res value
rather than the expected -EINVAL.

Setup ->bytes_done before potentially failing, so we have a consistent
value if we fail the request early.

Cc: stable@vger.kernel.org
Reported-by: xingwei lee <xrivendell7@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

io_uring: don't check iopoll if request completes

commit 9b43ef3d52532a0175ed6654618f7db61d390d2e upstream.

IOPOLL request should never return IOU_OK, so the following iopoll
queueing check in io_issue_sqe() after getting IOU_OK doesn't make any
sense as would never turn true. Let's optimise on that and return a bit
earlier. It's also much more resilient to potential bugs from
mischieving iopoll implementations.

Cc: <stable@vger.kernel.org>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/2f8690e2fa5213a2ff292fac29a7143c036cdd60.1701390926.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

LoongArch: Fix and simplify fcsr initialization on execve()

commit c2396651309eba291c15e32db8fbe44c738b5921 upstream.

There has been a lingering bug in LoongArch Linux systems causing some
GCC tests to intermittently fail (see Closes link).  I've made a minimal
reproducer:

    zsh% cat measure.s
    .align 4
    .globl _start
    _start:
        movfcsr2gr  $a0, $fcsr0
        bstrpick.w  $a0, $a0, 16, 16
        beqz        $a0, .ok
        break       0
    .ok:
        li.w        $a7, 93
        syscall     0
    zsh% cc mesaure.s -o measure -nostdlib
    zsh% echo $((1.0/3))
    0.33333333333333331
    zsh% while ./measure; do ; done

This while loop should not stop as POSIX is clear that execve must set
fenv to the default, where FCSR should be zero.  But in fact it will
just stop after running for a while (normally less than 30 seconds).
Note that "$((1.0/3))" is needed to reproduce this issue because it
raises FE_INVALID and makes fcsr0 non-zero.

The problem is we are currently relying on SET_PERSONALITY2() to reset
current->thread.fpu.fcsr.  But SET_PERSONALITY2() is executed before
start_thread which calls lose_fpu(0).  We can see if kernel preempt is
enabled, we may switch to another thread after SET_PERSONALITY2() but
before lose_fpu(0).  Then bad thing happens: during the thread switch
the value of the fcsr0 register is stored into current->thread.fpu.fcsr,
making it dirty again.

The issue can be fixed by setting current->thread.fpu.fcsr after
lose_fpu(0) because lose_fpu() clears TIF_USEDFPU, then the thread
switch won't touch current->thread.fpu.fcsr.

The only other architecture setting FCSR in SET_PERSONALITY2() is MIPS.
I've ran a similar test on MIPS with mainline kernel and it turns out
MIPS is buggy, too.  Anyway MIPS do this for supporting different FP
flavors (NaN encodings, etc.) which do not exist on LoongArch.  So for
LoongArch, we can simply remove the current->thread.fpu.fcsr setting
from SET_PERSONALITY2() and do it in start_thread(), after lose_fpu(0).

The while loop failing with the mainline kernel has survived one hour
after this change on LoongArch.

Fixes: 803b0fc5c3f2baa ("LoongArch: Add process management")
Closes: https://github.com/loongson-community/discussions/issues/7
Link: https://lore.kernel.org/linux-mips/7a6aa1bbdbbe2e63ae96ff163fab0349f58f1b9e.camel@xry111.site/
Cc: stable@vger.kernel.org
Signed-off-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ceph: select FS_ENCRYPTION_ALGS if FS_ENCRYPTION

commit 9c896d6bc3dfef86659a6a1fb25ccdea5dbef6a3 upstream.

The kconfig options for filesystems that support FS_ENCRYPTION are
supposed to select FS_ENCRYPTION_ALGS.  This is needed to ensure that
required crypto algorithms get enabled as loadable modules or builtin as
is appropriate for the set of enabled filesystems.  Do this for CEPH_FS
so that there aren't any missing algorithms if someone happens to have
CEPH_FS as their only enabled filesystem that supports encryption.

Cc: stable@vger.kernel.org
Fixes: f061feda6c54 ("ceph: add fscrypt ioctls and ceph.fscrypt.auth vxattr")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ksmbd: only v2 leases handle the directory

commit 77bebd186442a7d703b796784db7495129cc3e70 upstream.

When smb2 leases is disable, ksmbd can send oplock break notification
and cause wait oplock break ack timeout. It may appear like hang when
accessing a directory. This patch make only v2 leases handle the
directory.

Cc: stable@vger.kernel.org
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ksmbd: fix UAF issue in ksmbd_tcp_new_connection()

commit 38d20c62903d669693a1869aa68c4dd5674e2544 upstream.

The race is between the handling of a new TCP connection and
its disconnection. It leads to UAF on `struct tcp_transport` in
ksmbd_tcp_new_connection() function.

Cc: stable@vger.kernel.org
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-22991
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ksmbd: validate mech token in session setup

commit 92e470163d96df8db6c4fa0f484e4a229edb903d upstream.

If client send invalid mech token in session setup request, ksmbd
validate and make the error if it is invalid.

Cc: stable@vger.kernel.org
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-22890
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek: Enable headset mic on Lenovo M70 Gen5

commit fb3c007fde80d9d3b4207943e74c150c9116cead upstream.

Lenovo M70 Gen5 is equipped with ALC623, and it needs
ALC283_FIXUP_HEADSET_MIC quirk to make its headset mic work.

Signed-off-by: Bin Li <bin.li@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240117154123.21578-1-bin.li@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek: Enable mute/micmute LEDs and limit mic boost on HP ZBook

commit b018cee7369896c7a15bfdbe88f168f3dbd8ba27 upstream.

On some HP ZBooks, the audio LEDs can be enabled by
ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF. So use it accordingly.

Signed-off-by: Yo-Jung Lin <leo.lin@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240116020722.27236-1-leo.lin@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/relatek: Enable Mute LED on HP Laptop 15s-fq2xxx

commit bc7863d18677df66b2c7a0e172c91296ff380f11 upstream.

This HP Laptop uses ALC236 codec with COEF 0x07 idx 1 controlling
the mute LED. This patch enables the already existing quirk for
this device.

Signed-off-by: Çağhan Demir <caghandemir@marun.edu.tr>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240115172303.4718-1-caghandemir@marun.edu.tr
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: oxygen: Fix right channel of capture volume mixer

commit a03cfad512ac24a35184d7d87ec0d5489e1cb763 upstream.

There was a typo in oxygen mixer code that didn't update the right
channel value properly for the capture volume.  Let's fix it.

This trivial fix was originally reported on Bugzilla.

Fixes: a3601560496d ("[ALSA] oxygen: add front panel controls")
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=156561
Link: https://lore.kernel.org/r/20240112111023.6208-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: omap: do not override settings for RS485 support

commit 51f93776b84dee23e44a7be880736669a01cec2b upstream.

The drivers RS485 support is deactivated if there is no RTS GPIO available.
This is done by nullifying the ports rs485_supported struct. After that
however the settings in serial_omap_rs485_supported are assigned to the
same structure unconditionally, which results in an unintended reactivation
of RS485 support.

Fix this by moving the assignment to the beginning of
serial_omap_probe_rs485() and thus before uart_get_rs485_mode() gets
called.

Also replace the assignment of rs485_config() to have the complete RS485
setup in one function.

Fixes: e2752ae3cfc9 ("serial: omap: Disallow RS-485 if rts-gpio is not specified")
Cc: <stable@vger.kernel.org>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240103061818.564-7-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_exar: Set missing rs485_supported flag

commit 0c2a5f471ce58bca8f8ab5fcb911aff91eaaa5eb upstream.

The UART supports an auto-RTS mode in which the RTS pin is automatically
activated during transmission. So mark this mode as being supported even
if RTS is not controlled by the driver but the UART.

Also the serial core expects now at least one of both modes rts-on-send or
rts-after-send to be supported. This is since during sanitization
unsupported flags are deleted from a RS485 configuration set by userspace.
However if the configuration ends up with both flags unset, the core prints
a warning since it considers such a configuration invalid (see
uart_sanitize_serial_rs485()).

Cc: <stable@vger.kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-8-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: imx: Ensure that imx_uart_rs485_config() is called with enabled clock

commit 7c45eaa813476bd195ac1227a64b52f9cf2e2030 upstream.

There are register accesses in the function imx_uart_rs485_config(). The
clock must be enabled for these accesses. This was ensured by calling it
via the function uart_rs485_config() in the probe() function within the
range where the clock is enabled. With the commit 7c7f9bc986e6 ("serial:
Deassert Transmit Enable on probe in driver-specific way") it was removed
from the probe() function and is now only called through the function
uart_add_one_port() which is located at the end of the probe() function.
But the clock is already switched off in this area. To ensure that the
clock is enabled during register access, move the disabling of the clock
to the very end of the probe() function. To avoid leaking enabled clocks
on error also add an error path for exiting with disabling the clock.

Fixes: 7c7f9bc986e6 ("serial: Deassert Transmit Enable on probe in driver-specific way")
Cc: stable <stable@kernel.org>
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20231226113647.39376-1-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: core, imx: do not set RS485 enabled if it is not supported

commit 74eab89b26ac433ad857292f4707b43c1a8f0209 upstream.

If the imx driver cannot support RS485 it nullifies the ports
rs485_supported structure. But it still calls uart_get_rs485_mode() which
may set the RS485_ENABLED flag nevertheless.

This may lead to an attempt to configure RS485 even if it is not supported
when the flag is evaluated in uart_configure_port() at port startup.

Avoid this by bailing out of uart_get_rs485_mode() if the RS485_ENABLED
flag is not supported by the caller.

With this fix a check for RTS availability is now obsolete in the imx
driver, since it can not evaluate to true any more. So remove this check.

Furthermore the explicit nullifcation of rs485_supported is not needed,
since the memory has already been set to zeros at allocation. So remove
this, too.

Fixes: 00d7a00e2a6f ("serial: imx: Fill in rs485_supported")
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <stable@vger.kernel.org>
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240103061818.564-6-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_bcm2835aux: Restore clock error handling

commit 83e571f054cd742eb9a46d46ef05193904adf53f upstream.

The commit fcc446c8aa63 ("serial: 8250_bcm2835aux: Add ACPI support")
dropped the error handling for clock acquiring. But even an optional
clock needs this.

Fixes: fcc446c8aa63 ("serial: 8250_bcm2835aux: Add ACPI support")
Cc: stable <stable@kernel.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231220114334.4712-1-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: core: make sure RS485 cannot be enabled when it is not supported

commit c73986913fa47e71e0b1ad7f039f6444915e8810 upstream.

Some uart drivers specify a rs485_config() function and then decide later
to disable RS485 support for some reason (e.g. imx and ar933).

In these cases userspace may be able to activate RS485 via TIOCSRS485
nevertheless, since in uart_set_rs485_config() an existing rs485_config()
function indicates that RS485 is supported.

Make sure that this is not longer possible by checking the uarts
rs485_supported.flags instead and bailing out if SER_RS485_ENABLED is not
set.

Furthermore instead of returning an empty structure return -ENOTTY if the
RS485 configuration is requested via TIOCGRS485 but RS485 is not supported.
This has a small impact on userspace visibility but it is consistent with
the -ENOTTY error for TIOCGRS485.

Fixes: e849145e1fdd ("serial: ar933x: Fill in rs485_supported")
Fixes: 55e18c6b6d42 ("serial: imx: Remove serial_rs485 sanitization")
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <stable@vger.kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-5-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: core: fix sanitizing check for RTS settings

commit 4afeced55baa391490b61ed9164867e2927353ed upstream.

Among other things uart_sanitize_serial_rs485() tests the sanity of the RTS
settings in a RS485 configuration that has been passed by userspace.
If RTS-on-send and RTS-after-send are both set or unset the configuration
is adjusted and RTS-after-send is disabled and RTS-on-send enabled.

This however makes only sense if both RTS modes are actually supported by
the driver.

With commit be2e2cb1d281 ("serial: Sanitize rs485_struct") the code does
take the driver support into account but only checks if one of both RTS
modes are supported. This may lead to the errorneous result of RTS-on-send
being set even if only RTS-after-send is supported.

Fix this by changing the implemented logic: First clear all unsupported
flags in the RS485 configuration, then adjust an invalid RTS setting by
taking into account which RTS mode is supported.

Cc: <stable@vger.kernel.org>
Fixes: be2e2cb1d281 ("serial: Sanitize rs485_struct")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-4-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: phy: qcom,sc8280xp-qmp-usb43dp-phy: fix path to header

commit 21a1d02579ae75fd45555b84d20ba55632a14a19 upstream.

Fix the path to bindings header in description.

Fixes: e1c4c5436b4a ("dt-bindings: phy: qcom,qmp-usb3-dp: fix sc8280xp binding")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20231218130553.45893-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: mon: Fix atomicity violation in mon_bin_vma_fault

commit 2dd23cc4d0e6aa55cf9fb3b05f2f4165b01de81c upstream.

In mon_bin_vma_fault():
    offset = vmf->pgoff << PAGE_SHIFT;
    if (offset >= rp->b_size)
        return VM_FAULT_SIGBUS;
    chunk_idx = offset / CHUNK_SIZE;
    pageptr = rp->b_vec[chunk_idx].pg;
The code is executed without holding any lock.

In mon_bin_vma_close():
    spin_lock_irqsave(&rp->b_lock, flags);
    rp->mmap_active--;
    spin_unlock_irqrestore(&rp->b_lock, flags);

In mon_bin_ioctl():
    spin_lock_irqsave(&rp->b_lock, flags);
    if (rp->mmap_active) {
        ...
    } else {
        ...
        kfree(rp->b_vec);
        rp->b_vec  = vec;
        rp->b_size = size;
        ...
    }
    spin_unlock_irqrestore(&rp->b_lock, flags);

Concurrent execution of mon_bin_vma_fault() with mon_bin_vma_close() and
mon_bin_ioctl() could lead to atomicity violations. mon_bin_vma_fault()
accesses rp->b_size and rp->b_vec without locking, risking array
out-of-bounds access or use-after-free bugs due to possible modifications
in mon_bin_ioctl().

This possible bug is found by an experimental static analysis tool
developed by our team, BassCheck[1]. This tool analyzes the locking APIs
to extract function pairs that can be concurrently executed, and then
analyzes the instructions in the paired functions to identify possible
concurrency bugs including data races and atomicity violations. The above
possible bug is reported when our tool analyzes the source code of
Linux 6.2.

To address this issue, it is proposed to add a spin lock pair in
mon_bin_vma_fault() to ensure atomicity. With this patch applied, our tool
never reports the possible bug, with the kernel configuration allyesconfig
for x86_64. Due to the lack of associated hardware, we cannot test the
patch in runtime testing, and just verify it according to the code logic.

[1] https://sites.google.com/view/basscheck/

Fixes: 19e6317d24c2 ("usb: mon: Fix a deadlock in usbmon between ...")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gui-Dong Han <2045gemini@gmail.com>
Link: https://lore.kernel.org/r/20240105052412.9377-1-2045gemini@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: class: fix typec_altmode_put_partner to put plugs

commit 5962ded777d689cd8bf04454273e32228d7fb71f upstream.

When typec_altmode_put_partner is called by a plug altmode upon release,
the port altmode the plug belongs to will not remove its reference to the
plug. The check to see if the altmode being released is a plug evaluates
against the released altmode's partner instead of the calling altmode, so
change adev in typec_altmode_put_partner to properly refer to the altmode
being released.

Because typec_altmode_set_partner calls get_device() on the port altmode,
add partner_adev that points to the port altmode in typec_put_partner to
call put_device() on. typec_altmode_set_partner is not called for port
altmodes, so add a check in typec_altmode_release to prevent
typec_altmode_put_partner() calls on port altmode release.

Fixes: 8a37d87d72f0 ("usb: typec: Bus type for alternate modes")
Cc: <stable@vger.kernel.org>
Co-developed-by: Christian A. Ehrhardt <lk@c--e.de>
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Tested-by: Christian A. Ehrhardt <lk@c--e.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240103181754.2492492-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "usb: typec: class: fix typec_altmode_put_partner to put plugs"

commit 9c6b789e954fae73c548f39332bcc56bdf0d4373 upstream.

This reverts commit b17b7fe6dd5c6ff74b38b0758ca799cdbb79e26e.

That commit messed up the reference counting, so it needs to
be rethought.

Fixes: b17b7fe6dd5c ("usb: typec: class: fix typec_altmode_put_partner to put plugs")
Cc: <stable@vger.kernel.org>
Cc: RD Babiera <rdbabiera@google.com>
Reported-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Closes: https://lore.kernel.org/lkml/CAP-bSRb3SXpgo_BEdqZB-p1K5625fMegRZ17ZkPE1J8ZYgEHDg@mail.gmail.com/
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240102091142.2136472-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: cdns3: Fix uvc fail when DMA cross 4k boundery since sg enabled

commit 40c304109e866a7dc123661a5c8ca72f6b5e14e0 upstream.

Supposed DMA cross 4k bounder problem should be fixed at DEV_VER_V2, but
still met problem when do ISO transfer if sg enabled.

Data pattern likes below when sg enabled, package size is 1k and mult is 2
[UVC Header(8B) ] [data(3k - 8)] ...

The received data at offset 0xd000 will get 0xc000 data, len 0x70. Error
happen position as below pattern:
0xd000: wrong
0xe000: wrong
0xf000: correct
0x10000: wrong
0x11000: wrong
0x12000: correct
...

To avoid DMA cross 4k bounder at ISO transfer, reduce burst len according
to start DMA address's alignment.

Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-4-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: cdns3: fix iso transfer error when mult is not zero

commit 92f02efa1d86d7dcaef7f38a5fe3396c4e88a93c upstream.

ISO basic transfer is
ITP(SOF) Package_0 Package_1 ... Package_n

CDNS3 DMA start dma transfer from memmory to internal FIFO when get SOF,
controller will transfer data to usb bus from internal FIFO when get IN
token.

According USB spec defination:
Maximum number of packets = (bMaxBurst + 1) * (Mult + 1)

Internal memory should be the same as (bMaxBurst + 1) * (Mult + 1). DMA
don't fetch data advance when ISO transfer, so only reserve
(bMaxBurst + 1) * (Mult + 1) internal memory for ISO transfer.

Need save Mult and bMaxBurst information and set it into EP_CFG register,
otherwise only 1 package is sent by controller, other package will be
lost.

Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-3-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: cdns3: fix uvc failure work since sg support enabled

commit 1b8be5ecff26201bafb0a554c74e91571299fb94 upstream.

When IP version >= DEV_VER_V2, gadget:sg_supported is true. So uvc gadget
function driver will use sg to equeue data, first is 8bytes header, the
second is 1016bytes data.

    cdns3_prepare_trb: ep2in: trb 0000000000ac755f, dma buf: 0xbf455000, size: 8, burst: 128 ctrl: 0x00000415 (C=1, T=0, ISP, CHAIN, Normal)
    cdns3_prepare_trb: ep2in: trb 00000000a574e693, dma buf: 0xc0200fe0, size: 1016, burst: 128 ctrl: 0x00000405 (C=1, T=0, ISP, Normal)

But cdns3_ep_run_transfer() can't correctly handle this case, which only
support one TRB for ISO transfer.

The controller requires duplicate the TD for each SOF if priv_ep->interval
is not 1. DMA will read data from DDR to internal FIFO when get SOF. Send
data to bus when receive IN token. DMA always refill FIFO when get SOF
regardless host send IN token or not. If host send IN token later, some
frames data will be lost.

Fixed it by below major steps:

1. Calculate numembers of TRB base on sg_nums and priv_ep->interval.
2. Remove CHAIN flags for each end TRB of TD when duplicate TD.
3. The controller requires LINK TRB must be first TRB of TD. When check
there are not enough TRBs lefts, just fill LINK TRB for left TRBs.

.... CHAIN_TRB DATA_TRB, CHAIN_TRB DATA_TRB,  LINK_TRB ... LINK_TRB
                                                           ^End of TRB List

Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: chipidea: wait controller resume finished for wakeup irq

commit 128d849074d05545becf86e713715ce7676fc074 upstream.

After the chipidea driver introduce extcon for id and vbus, it's able
to wakeup from another irq source, in case the system with extcon ID
cable, wakeup from usb ID cable and device removal, the usb device
disconnect irq may come firstly before the extcon notifier while system
resume, so we will get 2 "wakeup" irq, one for usb device disconnect;
and one for extcon ID cable change(real wakeup event), current driver
treat them as 2 successive wakeup irq so can't handle it correctly, then
finally the usb irq can't be enabled. This patch adds a check to bypass
further usb events before controller resume finished to fix it.

Fixes: 1f874edcb731 ("usb: chipidea: add runtime power management support")
cc:  <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20231228110753.1755756-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "usb: dwc3: don't reset device side if dwc3 was configured as host-only"

commit afe28cd686aeb77e8d9140d50fb1cf06a7ecb731 upstream.

This reverts commit e835c0a4e23c38531dcee5ef77e8d1cf462658c7.

Don't omit soft-reset. During initialization, the driver may need to
perform a soft reset to ensure the phy is ready when the controller
updates the GCTL.PRTCAPDIR or other settings by issuing phy soft-reset.
Many platforms often have access to DCTL register for soft-reset despite
being host-only. If there are actual reported issues from the platforms
that don't expose DCTL registers, then we will need to revisit (perhaps
to teach dwc3 to perform xhci's soft-reset USBCMD.HCRST).

Cc: <stable@vger.kernel.org>
Fixes: e835c0a4e23c ("usb: dwc3: don't reset device side if dwc3 was configured as host-only")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/7668ab11a48f260820825274976eb41fec7f54d1.1703282469.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "usb: dwc3: Soft reset phy on probe for host"

commit 7059fbebcb00554c3f31e5b5d93ef6d2d96dc7b4 upstream.

This reverts commit 8bea147dfdf823eaa8d3baeccc7aeb041b41944b.

The phy soft reset GUSB2PHYCFG.PHYSOFTRST only applies to UTMI phy, not
ULPI. This fix is incomplete.

Cc: <stable@vger.kernel.org>
Fixes: 8bea147dfdf8 ("usb: dwc3: Soft reset phy on probe for host")
Reported-by: Köry Maincent <kory.maincent@bootlin.com>
Closes: https://lore.kernel.org/linux-usb/20231205151959.5236c231@kmaincent-XPS-13-7390
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/29a26593a60eba727de872a3e580a674807b3339.1703282469.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: gadget: Queue PM runtime idle on disconnect event

commit 3c7af52c7616c3aa6dacd2336ec748d4a65df8f4 upstream.

There is a scenario where DWC3 runtime suspend is blocked due to the
dwc->connected flag still being true while PM usage_count is zero after
DWC3 giveback is completed and the USB gadget session is being terminated.
This leads to a case where nothing schedules a PM runtime idle for the
device.

The exact condition is seen with the following sequence:
  1.  USB bus reset is issued by the host
  2.  Shortly after, or concurrently, a USB PD DR SWAP request is received
      (sink->source)
  3.  USB bus reset event handler runs and issues
      dwc3_stop_active_transfers(), and pending transfer are stopped
  4.  DWC3 usage_count decremented to 0, and runtime idle occurs while
      dwc->connected == true, returns -EBUSY
  5.  DWC3 disconnect event seen, dwc->connected set to false due to DR
      swap handling
  6.  No runtime idle after this point

Address this by issuing an asynchronous PM runtime idle call after the
disconnect event is completed, as it modifies the dwc->connected flag,
which is what blocks the initial runtime idle.

Fixes: fc8bb91bc83e ("usb: dwc3: implement runtime PM")
Cc: <stable@vger.kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240103214946.2596-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: gadget: Handle EP0 request dequeuing properly

commit 730e12fbec53ab59dd807d981a204258a4cfb29a upstream.

Current EP0 dequeue path will share the same as other EPs.  However, there
are some special considerations that need to be made for EP0 transfers:

  - EP0 transfers never transition into the started_list
  - EP0 only has one active request at a time

In case there is a vendor specific control message for a function over USB
FFS, then there is no guarantee on the timeline which the DATA/STATUS stage
is responded to.  While this occurs, any attempt to end transfers on
non-control EPs will end up having the DWC3_EP_DELAY_STOP flag set, and
defer issuing of the end transfer command.  If the USB FFS application
decides to timeout the control transfer, or if USB FFS AIO path exits, the
USB FFS driver will issue a call to usb_ep_dequeue() for the ep0 request.

In case of the AIO exit path, the AIO FS blocks until all pending USB
requests utilizing the AIO path is completed.  However, since the dequeue
of ep0 req does not happen properly, all non-control EPs with the
DWC3_EP_DELAY_STOP flag set will not be handled, and the AIO exit path will
be stuck waiting for the USB FFS data endpoints to receive a completion
callback.

Fix is to utilize dwc3_ep0_reset_state() in the dequeue API to ensure EP0
is brought back to the SETUP state, and ensures that any deferred end
transfer commands are handled.  This also will end any active transfers
on EP0, compared to the previous implementation which directly called
giveback only.

Fixes: fcd2def66392 ("usb: dwc3: gadget: Refactor dwc3_gadget_ep_dequeue")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20231206201814.32664-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc: ep0: Update request status in dwc3_ep0_stall_restart

commit e9d40b215e38480fd94c66b06d79045717a59e9c upstream.

Current implementation blocks the running operations when Plug-out and
Plug-In is performed continuously, process gets stuck in
dwc3_thread_interrupt().

Code Flow:

CPU1

->Gadget_start
->dwc3_interrupt
->dwc3_thread_interrupt
->dwc3_process_event_buf
->dwc3_process_event_entry
->dwc3_endpoint_interrupt
->dwc3_ep0_interrupt
->dwc3_ep0_inspect_setup
->dwc3_ep0_stall_and_restart

By this time if pending_list is not empty, it will get the next request
on the given list and calls dwc3_gadget_giveback which will unmap request
and call its complete() callback to notify upper layers that it has
completed. Currently dwc3_gadget_giveback status is set to -ECONNRESET,
whereas it should be -ESHUTDOWN based on condition if not dwc->connected
is true.

Cc: <stable@vger.kernel.org>
Fixes: d742220b3577 ("usb: dwc3: ep0: giveback requests on stall_and_restart")
Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com>
Link: https://lore.kernel.org/r/20231222094704.20276-1-quic_uaggarwa@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: phy: mxs: remove CONFIG_USB_OTG condition for mxs_phy_is_otg_host()

commit ff2b89de471da942a4d853443688113a44fd35ed upstream.

When CONFIG_USB_OTG is not set, mxs_phy_is_otg_host() will always return
false. This behaviour is wrong. Since phy.last_event will always be set
for either host or device mode. Therefore, CONFIG_USB_OTG condition
can be removed.

Fixes: 5eda42aebb76 ("usb: phy: mxs: fix getting wrong state with mxs_phy_is_otg_host()")
cc:  <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20231228110753.1755756-3-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "usb: gadget: f_uvc: change endpoint allocation in uvc_function_bind()"

commit 895ee5aefb7e24203de5dffae7ce9a02d78fa3d1 upstream.

This reverts commit 3c5b006f3ee800b4bd9ed37b3a8f271b8560126e.

gadget_is_{super|dual}speed() API check UDC controller capitblity. It
should pass down highest speed endpoint descriptor to UDC controller. So
UDC controller driver can reserve enough resource at check_config(),
especially mult and maxburst. So UDC driver (such as cdns3) can know need
at least (mult + 1) * (maxburst + 1) * wMaxPacketSize internal memory for
this uvc functions.

Cc: <stable@vger.kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-5-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug

commit 71fee48fb772ac4f6cfa63dbebc5629de8b4cc09 upstream.

When offlining and onlining CPUs the overall reported idle and iowait
times as reported by /proc/stat jump backward and forward:

cpu  132 0 176 225249 47 6 6 21 0 0
cpu0 80 0 115 112575 33 3 4 18 0 0
cpu1 52 0 60 112673 13 3 1 2 0 0

cpu  133 0 177 226681 47 6 6 21 0 0
cpu0 80 0 116 113387 33 3 4 18 0 0

cpu  133 0 178 114431 33 6 6 21 0 0 <---- jump backward
cpu0 80 0 116 114247 33 3 4 18 0 0
cpu1 52 0 61 183 0 3 1 2 0 0        <---- idle + iowait start with 0

cpu  133 0 178 228956 47 6 6 21 0 0 <---- jump forward
cpu0 81 0 117 114929 33 3 4 18 0 0

Reason for this is that get_idle_time() in fs/proc/stat.c has different
sources for both values depending on if a CPU is online or offline:

- if a CPU is online the values may be taken from its per cpu
  tick_cpu_sched structure

- if a CPU is offline the values are taken from its per cpu cpustat
  structure

The problem is that the per cpu tick_cpu_sched structure is set to zero on
CPU offline. See tick_cancel_sched_timer() in kernel/time/tick-sched.c.

Therefore when a CPU is brought offline and online afterwards both its idle
and iowait sleeptime will be zero, causing a jump backward in total system
idle and iowait sleeptime. In a similar way if a CPU is then brought
offline again the total idle and iowait sleeptimes will jump forward.

It looks like this behavior was introduced with commit 4b0c0f294f60
("tick: Cleanup NOHZ per cpu data on cpu down").

This was only noticed now on s390, since we switched to generic idle time
reporting with commit be76ea614460 ("s390/idle: remove arch_cpu_idle_time()
and corresponding code").

Fix this by preserving the values of idle_sleeptime and iowait_sleeptime
members of the per-cpu tick_sched structure on CPU hotplug.

Fixes: 4b0c0f294f60 ("tick: Cleanup NOHZ per cpu data on cpu down")
Reported-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20240115163555.1004144-1-hca@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64s: Increase default stack size to 32KB

commit 18f14afe281648e31ed35c9ad2fcb724c4838ad9 upstream.

There are reports of kernels crashing due to stack overflow while
running OpenShift (Kubernetes). The primary contributor to the stack
usage seems to be openvswitch, which is used by OVN-Kubernetes (based on
OVN (Open Virtual Network)), but NFS also contributes in some stack
traces.

There may be some opportunities to reduce stack usage in the openvswitch
code, but doing so potentially require tradeoffs vs performance, and
also requires testing across architectures.

Looking at stack usage across the kernel (using -fstack-usage), shows
that ppc64le stack frames are on average 50-100% larger than the
equivalent function built for x86-64. Which is not surprising given the
minimum stack frame size is 32 bytes on ppc64le vs 16 bytes on x86-64.

So increase the default stack size to 32KB for the modern 64-bit Book3S
platforms, ie. pseries (virtualised) and powernv (bare metal). That
leaves the older systems like G5s, and the AmigaOne (pasemi) with a 16KB
stack which should be sufficient on those machines.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Aneesh Kumar K.V (IBM) <aneesh.kumar@kernel.org>
Link: https://msgid.link/20231215124449.317597-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clocksource/drivers/timer-ti-dm: Fix make W=n kerneldoc warnings

commit b99a212a7697c542b460adaa15d4a98abf8223f0 upstream.

Kernel test robot reports of kerneldoc related warnings that happen with
make W=n for "parameter or member not described".

These were caused by changes to function parameter names with
earlier commits where the kerneldoc parts were not updated.

Fixes: 49cd16bb573e ("clocksource/drivers/timer-ti-dm: Simplify register writes with dmtimer_write()")
Fixes: a6e543f61531 ("clocksource/drivers/timer-ti-dm: Move struct omap_dm_timer fields to driver")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202311040403.DzIiBuwU-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202311040606.XL5OcR9O-lkp@intel.com/
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20231114072930.40615-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

binder: fix race between mmput() and do_exit()

commit 9a9ab0d963621d9d12199df9817e66982582d5a5 upstream.

Task A calls binder_update_page_range() to allocate and insert pages on
a remote address space from Task B. For this, Task A pins the remote mm
via mmget_not_zero() first. This can race with Task B do_exit() and the
final mmput() refcount decrement will come from Task A.

  Task A            | Task B
  ------------------+------------------
  mmget_not_zero()  |
                    |  do_exit()
                    |    exit_mm()
                    |      mmput()
  mmput()           |
    exit_mmap()     |
      remove_vma()  |
        fput()      |

In this case, the work of ____fput() from Task B is queued up in Task A
as TWA_RESUME. So in theory, Task A returns to userspace and the cleanup
work gets executed. However, Task A instead sleep, waiting for a reply
from Task B that never comes (it's dead).

This means the binder_deferred_release() is blocked until an unrelated
binder event forces Task A to go back to userspace. All the associated
death notifications will also be delayed until then.

In order to fix this use mmput_async() that will schedule the work in
the corresponding mm->async_put_work WQ instead of Task A.

Fixes: 457b9a6f09f0 ("Staging: android: add binder driver")
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Link: https://lore.kernel.org/r/20231201172212.1813387-4-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen-netback: don't produce zero-size SKB frags

commit c7ec4f2d684e17d69bbdd7c4324db0ef5daac26a upstream.

While frontends may submit zero-size requests (wasting a precious slot),
core networking code as of at least 3ece782693c4b ("sock: skb_copy_ubufs
support for compound pages") can't deal with SKBs when they have all
zero-size fragments. Respond to empty requests right when populating
fragments; all further processing is fragment based and hence won't
encounter these empty requests anymore.

In a way this should have been that way from the beginning: When no data
is to be transferred for a particular request, there's not even a point
in validating the respective grant ref. That's no different from e.g.
passing NULL into memcpy() when at the same time the size is 0.

This is XSA-448 / CVE-2023-46838.

Cc: stable@vger.kernel.org
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "drm/amdkfd: Relocate TBA/TMA to opposite side of VM hole"

commit 0f35b0a7b8fa402adbffa2565047cdcc4c480153 upstream.

That commit causes NULL pointer dereferences in dmesgs when
running applications using ROCm, including clinfo, blender,
and PyTorch, since v6.6.1. Revert it to fix blender again.

This reverts commit 96c211f1f9ef82183493f4ceed4e347b52849149.

Closes: https://github.com/ROCm/ROCm/issues/2596
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2991
Reviewed-by: Jay Cornwall <jay.cornwall@amd.com>
Signed-off-by: Kaibo Ma <ent3rm4n@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rust: Ignore preserve-most functions

commit bad098d76835c1379e1cf6afc935f8a7e050f83c upstream.

Neither bindgen nor Rust know about the preserve-most calling
convention, and Clang describes it as unstable. Since we aren't using
functions with this calling convention from Rust, blocklist them.

These functions are only added to the build when list hardening is
enabled, which is likely why others didn't notice this yet.

Signed-off-by: Matthew Maurer <mmaurer@google.com>
Reviewed-by: Martin Rodriguez Reboredo <yakoyoku@gmail.com>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Link: https://lore.kernel.org/r/20231031201945.1412345-1-mmaurer@google.com
[ Used Markdown for consistency with the other comments in the file. ]
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: atkbd - use ab83 as id when skipping the getid command

commit 58f65f9db7e0de366a5a115c2e2c0703858bba69 upstream.

Barnabás reported that the change to skip the getid command
when the controller is in translated mode on laptops caused
the Version field of his "AT Translated Set 2 keyboard"
input device to change from ab83 to abba, breaking a custom
hwdb entry for this keyboard.

Use the standard ab83 id for keyboards when getid is skipped
(rather then that getid fails) to avoid reporting a different
Version to userspace then before skipping the getid.

Fixes: 936e4d49ecbc ("Input: atkbd - skip ATKBD_CMD_GETID in translated mode")
Reported-by: Barnabás Pőcze <pobrn@protonmail.com>
Closes: https://lore.kernel.org/linux-input/W1ydwoG2fYv85Z3C3yfDOJcVpilEvGge6UGa9kZh8zI2-qkHXp7WLnl2hSkFz63j-c7WupUWI5TLL6n7Lt8DjRuU-yJBwLYWrreb1hbnd6A=@protonmail.com/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240116204325.7719-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mips/smp: Call rcutree_report_cpu_starting() earlier

commit 55702ec9603ebeffb15e6f7b113623fe1d8872f4 upstream.

rcutree_report_cpu_starting() must be called before
clockevents_register_device() to avoid the following lockdep splat triggered by
calling list_add() when CONFIG_PROVE_RCU_LIST=y:

  WARNING: suspicious RCU usage
  ...
  -----------------------------
  kernel/locking/lockdep.c:3680 RCU-list traversed in non-reader section!!

  other info that might help us debug this:

  RCU used illegally from offline CPU!
  rcu_scheduler_active = 1, debug_locks = 1
  no locks held by swapper/1/0.
  ...
  Call Trace:
  [<ffffffff8012a434>] show_stack+0x64/0x158
  [<ffffffff80a93d98>] dump_stack_lvl+0x90/0xc4
  [<ffffffff801c9e9c>] __lock_acquire+0x1404/0x2940
  [<ffffffff801cbf3c>] lock_acquire+0x14c/0x448
  [<ffffffff80aa4260>] _raw_spin_lock_irqsave+0x50/0x88
  [<ffffffff8021e0c8>] clockevents_register_device+0x60/0x1e8
  [<ffffffff80130ff0>] r4k_clockevent_init+0x220/0x3a0
  [<ffffffff801339d0>] start_secondary+0x50/0x3b8

raw_smp_processor_id() is required in order to avoid calling into lockdep
before RCU has declared the CPU to be watched for readers.

See also commit 29368e093921 ("x86/smpboot:  Move rcu_cpu_starting() earlier"),
commit de5d9dae150c ("s390/smp: move rcu_cpu_starting() earlier") and commit
99f070b62322 ("powerpc/smp: Call rcu_cpu_starting() earlier").

Signed-off-by: Stefan Wiehler <stefan.wiehler@nokia.com>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

binder: fix unused alloc->free_async_space

commit c6d05e0762ab276102246d24affd1e116a46aa0c upstream.

Each transaction is associated with a 'struct binder_buffer' that stores
the metadata about its buffer area. Since commit 74310e06be4d ("android:
binder: Move buffer out of area shared with user space") this struct is
no longer embedded within the buffer itself but is instead allocated on
the heap to prevent userspace access to this driver-exclusive info.

Unfortunately, the space of this struct is still being accounted for in
the total buffer size calculation, specifically for async transactions.
This results in an additional 104 bytes added to every async buffer
request, and this area is never used.

This wasted space can be substantial. If we consider the maximum mmap
buffer space of SZ_4M, the driver will reserve half of it for async
transactions, or 0x200000. This area should, in theory, accommodate up
to 262,144 buffers of the minimum 8-byte size. However, after adding
the extra 'sizeof(struct binder_buffer)', the total number of buffers
drops to only 18,724, which is a sad 7.14% of the actual capacity.

This patch fixes the buffer size calculation to enable the utilization
of the entire async buffer space. This is expected to reduce the number
of -ENOSPC errors that are seen on the field.

Fixes: 74310e06be4d ("android: binder: Move buffer out of area shared with user space")
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Link: https://lore.kernel.org/r/20231201172212.1813387-6-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

binder: fix async space check for 0-sized buffers

commit 3091c21d3e9322428691ce0b7a0cfa9c0b239eeb upstream.

Move the padding of 0-sized buffers to an earlier stage to account for
this round up during the alloc->free_async_space check.

Fixes: 74310e06be4d ("android: binder: Move buffer out of area shared with user space")
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Link: https://lore.kernel.org/r/20231201172212.1813387-5-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

keys, dns: Fix size check of V1 server-list header

commit acc657692aed438e9931438f8c923b2b107aebf9 upstream.

Fix the size check added to dns_resolver_preparse() for the V1 server-list
header so that it doesn't give EINVAL if the size supplied is the same as
the size of the header struct (which should be valid).

This can be tested with:

        echo -n -e '\0\0\01\xff\0\0' | keyctl padd dns_resolver desc @p

which will give "add_key: Invalid argument" without this fix.

Fixes: 1997b3cb4217 ("keys, dns: Fix missing size check of V1 server-list header")
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Link: https://lore.kernel.org/r/ZZ4fyY4r3rqgZL+4@xpf.sh.intel.com/
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests/bpf: Add assert for user stacks in test_task_stack

commit 727a92d62fd6a382b4c5972008e45667e707b0e4 upstream.

This is a follow up to:
commit b8e3a87a627b ("bpf: Add crosstask check to __bpf_get_stack").

This test ensures that the task iterator only gets a single
user stack (for the current task).

Signed-off-by: Jordan Rome <linux@jordanrome.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20231112023010.144675-1-linux@jordanrome.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "kernfs: convert kernfs_idr_lock to an irq safe raw spinlock"

commit e3977e0609a07d86406029fceea0fd40d7849368 upstream.

This reverts commit dad3fb67ca1cbef87ce700e83a55835e5921ce8a.

The commit converted kernfs_idr_lock to an IRQ-safe raw_spinlock because it
could be acquired while holding an rq lock through bpf_cgroup_from_id().
However, kernfs_idr_lock is held while doing GPF_NOWAIT allocations which
involves acquiring an non-IRQ-safe and non-raw lock leading to the following
lockdep warning:

  =============================
  [ BUG: Invalid wait context ]
  6.7.0-rc5-kzm9g-00251-g655022a45b1c #578 Not tainted
  -----------------------------
  swapper/0/0 is trying to lock:
  dfbcd488 (&c->lock){....}-{3:3}, at: local_lock_acquire+0x0/0xa4
  other info that might help us debug this:
  context-{5:5}
  2 locks held by swapper/0/0:
   #0: dfbc9c60 (lock){+.+.}-{3:3}, at: local_lock_acquire+0x0/0xa4
   #1: c0c012a8 (kernfs_idr_lock){....}-{2:2}, at: __kernfs_new_node.constprop.0+0x68/0x258
  stack backtrace:
  CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.7.0-rc5-kzm9g-00251-g655022a45b1c #578
  Hardware name: Generic SH73A0 (Flattened Device Tree)
   unwind_backtrace from show_stack+0x10/0x14
   show_stack from dump_stack_lvl+0x68/0x90
   dump_stack_lvl from __lock_acquire+0x3cc/0x168c
   __lock_acquire from lock_acquire+0x274/0x30c
   lock_acquire from local_lock_acquire+0x28/0xa4
   local_lock_acquire from ___slab_alloc+0x234/0x8a8
   ___slab_alloc from __slab_alloc.constprop.0+0x30/0x44
   __slab_alloc.constprop.0 from kmem_cache_alloc+0x7c/0x148
   kmem_cache_alloc from radix_tree_node_alloc.constprop.0+0x44/0xdc
   radix_tree_node_alloc.constprop.0 from idr_get_free+0x110/0x2b8
   idr_get_free from idr_alloc_u32+0x9c/0x108
   idr_alloc_u32 from idr_alloc_cyclic+0x50/0xb8
   idr_alloc_cyclic from __kernfs_new_node.constprop.0+0x88/0x258
   __kernfs_new_node.constprop.0 from kernfs_create_root+0xbc/0x154
   kernfs_create_root from sysfs_init+0x18/0x5c
   sysfs_init from mnt_init+0xc4/0x220
   mnt_init from vfs_caches_init+0x6c/0x88
   vfs_caches_init from start_kernel+0x474/0x528
   start_kernel from 0x0

Let's rever the commit. It's undesirable to spread out raw spinlock usage
anyway and the problem can be solved by protecting the lookup path with RCU
instead.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Andrea Righi <andrea.righi@canonical.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: http://lkml.kernel.org/r/CAMuHMdV=AKt+mwY7svEq5gFPx41LoSQZ_USME5_MEdWQze13ww@mail.gmail.com
Link: https://lore.kernel.org/r/20240109214828.252092-2-tj@kernel.org
Tested-by: Andrea Righi <andrea.righi@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kernfs: convert kernfs_idr_lock to an irq safe raw spinlock

commit c312828c37a72fe2d033a961c47c227b0767e9f8 upstream.

bpf_cgroup_from_id() is basically a wrapper to cgroup_get_from_id(),
that is relying on kernfs to determine the right cgroup associated to
the target id.

As a kfunc, it has the potential to be attached to any function through
BPF, particularly in contexts where certain locks are held.

However, kernfs is not using an irq safe spinlock for kernfs_idr_lock,
that means any kernfs function that is acquiring this lock can be
interrupted and potentially hit bpf_cgroup_from_id() in the process,
triggering a deadlock.

For example, it is really easy to trigger a lockdep splat between
kernfs_idr_lock and rq->_lock, attaching a small BPF program to
__set_cpus_allowed_ptr_locked() that just calls bpf_cgroup_from_id():

 =====================================================
 WARNING: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected
 6.7.0-rc7-virtme #5 Not tainted
 -----------------------------------------------------
 repro/131 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
 ffffffffb2dc4578 (kernfs_idr_lock){+.+.}-{2:2}, at: kernfs_find_and_get_node_by_id+0x1d/0x80

 and this task is already holding:
 ffff911cbecaf218 (&rq->__lock){-.-.}-{2:2}, at: task_rq_lock+0x50/0xc0
 which would create a new lock dependency:
  (&rq->__lock){-.-.}-{2:2} -> (kernfs_idr_lock){+.+.}-{2:2}

 but this new dependency connects a HARDIRQ-irq-safe lock:
  (&rq->__lock){-.-.}-{2:2}

 ... which became HARDIRQ-irq-safe at:
   lock_acquire+0xbf/0x2b0
   _raw_spin_lock_nested+0x2e/0x40
   scheduler_tick+0x5d/0x170
   update_process_times+0x9c/0xb0
   tick_periodic+0x27/0xe0
   tick_handle_periodic+0x24/0x70
   __sysvec_apic_timer_interrupt+0x64/0x1a0
   sysvec_apic_timer_interrupt+0x6f/0x80
   asm_sysvec_apic_timer_interrupt+0x1a/0x20
   memcpy+0xc/0x20
   arch_dup_task_struct+0x15/0x30
   copy_process+0x1ce/0x1eb0
   kernel_clone+0xac/0x390
   kernel_thread+0x6f/0xa0
   kthreadd+0x199/0x230
   ret_from_fork+0x31/0x50
   ret_from_fork_asm+0x1b/0x30

 to a HARDIRQ-irq-unsafe lock:
  (kernfs_idr_lock){+.+.}-{2:2}

 ... which became HARDIRQ-irq-unsafe at:
 ...
   lock_acquire+0xbf/0x2b0
   _raw_spin_lock+0x30/0x40
   __kernfs_new_node.isra.0+0x83/0x280
   kernfs_create_root+0xf6/0x1d0
   sysfs_init+0x1b/0x70
   mnt_init+0xd9/0x2a0
   vfs_caches_init+0xcf/0xe0
   start_kernel+0x58a/0x6a0
   x86_64_start_reservations+0x18/0x30
   x86_64_start_kernel+0xc5/0xe0
   secondary_startup_64_no_verify+0x178/0x17b

 other info that might help us debug this:

  Possible interrupt unsafe locking scenario:

        CPU0                    CPU1
        ----                    ----
   lock(kernfs_idr_lock);
                                local_irq_disable();
                                lock(&rq->__lock);
                                lock(kernfs_idr_lock);
   <Interrupt>
     lock(&rq->__lock);

  *** DEADLOCK ***

Prevent this deadlock condition converting kernfs_idr_lock to a raw irq
safe spinlock.

The performance impact of this change should be negligible and it also
helps to prevent similar deadlock conditions with any other subsystems
that may depend on kernfs.

Fixes: 332ea1f697be ("bpf: Add bpf_cgroup_from_id() kfunc")
Cc: stable <stable@kernel.org>
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20231229074916.53547-1-andrea.righi@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

class: fix use-after-free in class_register()

commit 93ec4a3b76404bce01bd5c9032bef5df6feb1d62 upstream.

The lock_class_key is still registered and can be found in
lock_keys_hash hlist after subsys_private is freed in error
handler path.A task who iterate over the lock_keys_hash
later may cause use-after-free.So fix that up and unregister
the lock_class_key before kfree(cp).

On our platform, a driver fails to kset_register because of
creating duplicate filename '/class/xxx'.With Kasan enabled,
it prints a invalid-access bug report.

KASAN bug report:

BUG: KASAN: invalid-access in lockdep_register_key+0x19c/0x1bc
Write of size 8 at addr 15ffff808b8c0368 by task modprobe/252
Pointer tag: [15], memory tag: [fe]

CPU: 7 PID: 252 Comm: modprobe Tainted: G        W
 6.6.0-mainline-maybe-dirty #1

Call trace:
dump_backtrace+0x1b0/0x1e4
show_stack+0x2c/0x40
dump_stack_lvl+0xac/0xe0
print_report+0x18c/0x4d8
kasan_report+0xe8/0x148
__hwasan_store8_noabort+0x88/0x98
lockdep_register_key+0x19c/0x1bc
class_register+0x94/0x1ec
init_module+0xbc/0xf48 [rfkill]
do_one_initcall+0x17c/0x72c
do_init_module+0x19c/0x3f8
...
Memory state around the buggy address:
ffffff808b8c0100: 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a
ffffff808b8c0200: 8a 8a 8a 8a 8a 8a 8a 8a fe fe fe fe fe fe fe fe
>ffffff808b8c0300: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
                                     ^
ffffff808b8c0400: 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03

As CONFIG_KASAN_GENERIC is not set, Kasan reports invalid-access
not use-after-free here.In this case, modprobe is manipulating
the corrupted lock_keys_hash hlish where lock_class_key is already
freed before.

It's worth noting that this only can happen if lockdep is enabled,
which is not true for normal system.

Fixes: dcfbb67e48a2 ("driver core: class: use lock_class_key already present in struct subsys_private")
Cc: stable <stable@kernel.org>
Signed-off-by: Jing Xia <jing.xia@unisoc.com>
Signed-off-by: Xuewen Yan <xuewen.yan@unisoc.com>
Link: https://lore.kernel.org/r/20231220024603.186078-1-jing.xia@unisoc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

of: unittest: Fix of_count_phandle_with_args() expected value message

[ Upstream commit 716089b417cf98d01f0dc1b39f9c47e1d7b4c965 ]

The expected result value for the call to of_count_phandle_with_args()
was updated from 7 to 8, but the accompanying error message was
forgotten.

Fixes: 4dde83569832f937 ("of: Fix double free in of_parse_phandle_with_args_map")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240111085025.2073894-1-geert+renesas@glider.be
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fbdev: imxfb: fix left margin setting

[ Upstream commit 5758844105f7dd9a0a04990cd92499a1a593dd36 ]

The previous setting did not take into account the CSTN mode.
For the H_WAIT_2 bitfield (bits 0-7) of the LCDC Horizontal Configuration
Register (LCDCR), the IMX25RM manual states that:

In TFT mode, it specifies the number of SCLK periods between the end of
HSYNC and the beginning of OE signal, and the total delay time equals
(H_WAIT_2 + 3) of SCLK periods.
In CSTN mode, it specifies the number of SCLK periods between the end of
HSYNC and the first display data in each line, and the total delay time
equals (H_WAIT_2 + 2) of SCLK periods.

The patch handles both cases.

Fixes: 4e47382fbca9 ("fbdev: imxfb: warn about invalid left/right margin")
Fixes: 7e8549bcee00 ("imxfb: Fix margin settings")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

of: Fix double free in of_parse_phandle_with_args_map

[ Upstream commit 4dde83569832f9377362e50f7748463340c5db6b ]

In of_parse_phandle_with_args_map() the inner loop that
iterates through the map entries calls of_node_put(new)
to free the reference acquired by the previous iteration
of the inner loop. This assumes that the value of "new" is
NULL on the first iteration of the inner loop.

Make sure that this is true in all iterations of the outer
loop by setting "new" to NULL after its value is assigned to "cur".

Extend the unittest to detect the double free and add an additional
test case that actually triggers this path.

Fixes: bd6f2fd5a1 ("of: Support parsing phandle argument lists through a nexus node")
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Link: https://lore.kernel.org/r/20231229105411.1603434-1-lk@c--e.de
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ksmbd: validate the zero field of packet header

[ Upstream commit 516b3eb8c8065f7465f87608d37a7ed08298c7a5 ]

The SMB2 Protocol requires that "The first byte of the Direct TCP
transport packet header MUST be zero (0x00)"[1]. Commit 1c1bcf2d3ea0
("ksmbd: validate smb request protocol id") removed the validation of
this 1-byte zero. Add the validation back now.

[1]: [MS-SMB2] - v20230227, page 30.
https://winprotocoldoc.blob.core.windows.net/productionwindowsarchives/MS-SMB2/%5bMS-SMB2%5d-230227.pdf

Fixes: 1c1bcf2d3ea0 ("ksmbd: validate smb request protocol id")
Signed-off-by: Li Nan <linan122@huawei.com>
Acked-by: Tom Talpey <tom@talpey.com>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

kselftest/alsa - conf: Stringify the printed errno in sysfs_get()

[ Upstream commit fd38dd6abda589a8771e7872e4dea28c99c6a6ef ]

GCC 13.2.0 reported the warning of the print format specifier:

conf.c: In function ‘sysfs_get’:
conf.c:181:72: warning: format ‘%s’ expects argument of type ‘char *’, \
but argument 3 has type ‘int’ [-Wformat=]
  181 |                 ksft_exit_fail_msg("sysfs: unable to read value '%s': %s\n",
      |                                                                       ~^
      |                                                                        |
      |                                                                        char *
      |                                                                       %d

The fix passes strerror(errno) as it was intended, like in the sibling error
exit message.

Fixes: aba51cd0949ae ("selftests: alsa - add PCM test")
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: linux-sound@vger.kernel.org
Cc: linux-kselftest@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240107173704.937824-5-mirsad.todorovac@alu.unizg.hr
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

kselftest/alsa - mixer-test: Fix the print format specifier warning

[ Upstream commit 3f47c1ebe5ca9c5883e596c7888dec4bec0176d8 ]

The GCC 13.2.0 compiler issued the following warning:

mixer-test.c: In function ‘ctl_value_index_valid’:
mixer-test.c:322:79: warning: format ‘%lld’ expects argument of type ‘long long int’, \
      but argument 5 has type ‘long int’ [-Wformat=]
  322 |                         ksft_print_msg("%s.%d value %lld more than maximum %lld\n",
      |                                                                            ~~~^
      |                                                                               |
      |                                                                               long long int
      |                                                                            %ld
  323 |                                        ctl->name, index, int64_val,
  324 |                                        snd_ctl_elem_info_get_max(ctl->info));
      |                                        ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
      |                                        |
      |                                        long int

Fixing the format specifier as advised by the compiler suggestion removes the
warning.

Fixes: 3f48b137d88e7 ("kselftest: alsa: Factor out check that values meet constraints")
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: linux-sound@vger.kernel.org
Cc: linux-kselftest@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240107173704.937824-3-mirsad.todorovac@alu.unizg.hr
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

kselftest/alsa - mixer-test: fix the number of parameters to ksft_exit_fail_msg()

[ Upstream commit 8c51c13dc63d46e754c44215eabc0890a8bd9bfb ]

Minor fix in the number of arguments to error reporting function in the
test program as reported by GCC 13.2.0 warning.

mixer-test.c: In function ‘find_controls’:
mixer-test.c:169:44: warning: too many arguments for format [-Wformat-extra-args]
  169 |                         ksft_exit_fail_msg("snd_ctl_poll_descriptors() failed for %d\n",
      |                                            ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

The number of arguments in call to ksft_exit_fail_msg() doesn't correspond
to the format specifiers, so this is adjusted resembling the sibling calls
to the error function.

Fixes: b1446bda56456 ("kselftest: alsa: Check for event generation when we write to controls")
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: linux-sound@vger.kernel.org
Cc: linux-kselftest@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240107173704.937824-2-mirsad.todorovac@alu.unizg.hr
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: avoid stringop-overflow warnings for dp_decide_lane_settings()

[ Upstream commit c966dc0e9d96dc44423c404a2628236f1200c24e ]

gcc prints a warning about a possible array overflow for a couple of
callers of dp_decide_lane_settings() after commit 1b56c90018f0 ("Makefile:
Enable -Wstringop-overflow globally"):

drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_training_fixed_vs_pe_retimer.c: In function 'dp_perform_fixed_vs_pe_training_sequence_legacy':
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_training_fixed_vs_pe_retimer.c:426:25: error: 'dp_decide_lane_settings' accessing 4 bytes in a region of size 1 [-Werror=stringop-overflow=]
  426 |                         dp_decide_lane_settings(lt_settings, dpcd_lane_adjust,
      |                         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  427 |                                         lt_settings->hw_lane_settings, lt_settings->dpcd_lane_settings);
      |                                         ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_training_fixed_vs_pe_retimer.c:426:25: note: referencing argument 4 of type 'union dpcd_training_lane[4]'

I'm not entirely sure what caused this, but changing the prototype to expect
a pointer instead of an array avoids the warnings.

Fixes: 7727e7b60f82 ("drm/amd/display: Improve robustness of FIXED_VS link training at DP1 rates")
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/pm/smu7: fix a memleak in smu7_hwmgr_backend_init

[ Upstream commit 2f3be3ca779b11c332441b10e00443a2510f4d7b ]

The hwmgr->backend, (i.e. data) allocated by kzalloc is not freed in
the error-handling paths of smu7_get_evv_voltages and
smu7_update_edc_leakage_table. However, it did be freed in the
error-handling of phm_initializa_dynamic_state_adjustment_rule_settings,
by smu7_hwmgr_backend_fini. So the lack of free in smu7_get_evv_voltages
and smu7_update_edc_leakage_table is considered a memleak in this patch.

Fixes: 599a7e9fe1b6 ("drm/amd/powerplay: implement smu7 hwmgr to manager asics with smu ip version 7.")
Fixes: 8f0804c6b7d0 ("drm/amd/pm: add edc leakage controller setting")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdkfd: Confirm list is non-empty before utilizing list_first_entry in kfd_topology.c

[ Upstream commit 499839eca34ad62d43025ec0b46b80e77065f6d8 ]

Before using list_first_entry, make sure to check that list is not
empty, if list is empty return -ENODATA.

Fixes the below:
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_topology.c:1347 kfd_create_indirect_link_prop() warn: can 'gpu_link' even be NULL?
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_topology.c:1428 kfd_add_peer_prop() warn: can 'iolink1' even be NULL?
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_topology.c:1433 kfd_add_peer_prop() warn: can 'iolink2' even be NULL?

Fixes: 0f28cca87e9a ("drm/amdkfd: Extend KFD device topology to surface peer-to-peer links")
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Suggested-by: Felix Kuehling <Felix.Kuehling@amd.com>
Suggested-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

IB/iser: Prevent invalidating wrong MR

[ Upstream commit 2f1888281e67205bd80d3e8f54dbd519a9653f26 ]

The iser_reg_resources structure has two pointers to MR but only one
mr_valid field. The implementation assumes that we use only *sig_mr when
pi_enable is true. Otherwise, we use only *mr. However, it is only
sometimes correct. Read commands without protection information occur even
when pi_enble is true. For example, the following SCSI commands have a
Data-In buffer but never have protection information: READ CAPACITY (16),
INQUIRY, MODE SENSE(6), MAINTENANCE IN. So, we use
*sig_mr for some SCSI commands and *mr for the other SCSI commands.

In most cases, it works fine because the remote invalidation is applied.
However, there are two cases when the remote invalidation is not
applicable.
 1. Small write commands when all data is sent as an immediate.
 2. The target does not support the remote invalidation feature.

The lazy invalidation is used if the remote invalidation is impossible.
Since, at the lazy invalidation, we always invalidate the MR we want to
use, the wrong MR may be invalidated.

To fix the issue, we need a field per MR that indicates the MR needs
invalidation. Since the ib_mr structure already has such a field, let's
use ib_mr.need_inval instead of iser_reg_resources.mr_valid.

Fixes: b76a439982f8 ("IB/iser: Use IB_WR_REG_MR_INTEGRITY for PI handover")
Link: https://lore.kernel.org/r/20231219072311.40989-1-sergeygo@nvidia.com
Acked-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Sergey Gorenko <sergeygo@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpio: sysfs: drop the mention of gpiochip_find() from sysfs code

[ Upstream commit e404b0cc9f0b0b551f3276a814d38abf1f26d98f ]

We have removed all callers of gpiochip_find() so don't mention it in
gpiolib-sysfs.c.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Stable-dep-of: 48e1b4d369cf ("gpiolib: remove the GPIO device from the list when it's unregistered")
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpiolib: provide gpio_device_find()

[ Upstream commit cfe102f63308c8c8e01199a682868a64b83f653e ]

gpiochip_find() is wrong and its kernel doc is misleading as the
function doesn't return a reference to the gpio_chip but just a raw
pointer. The chip itself is not guaranteed to stay alive, in fact it can
be deleted at any point. Also: other than GPIO drivers themselves,
nobody else has any business accessing gpio_chip structs.

Provide a new gpio_device_find() function that returns a real reference
to the opaque gpio_device structure that is guaranteed to stay alive for
as long as there are active users of it.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Stable-dep-of: 48e1b4d369cf ("gpiolib: remove the GPIO device from the list when it's unregistered")
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpiolib: make gpio_device_get() and gpio_device_put() public

[ Upstream commit 36aa129f221c9070afd8dff03154ab49702a5b1b ]

In order to start migrating away from accessing struct gpio_chip by
users other than their owners, let's first make the reference management
functions for the opaque struct gpio_device public in the driver.h
header.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Stable-dep-of: 48e1b4d369cf ("gpiolib: remove the GPIO device from the list when it's unregistered")
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdkfd: Fix type of 'dbg_flags' in 'struct kfd_process'

[ Upstream commit 217e85f97031791fb48a2d374c7bdcf439365b21 ]

dbg_flags looks to be defined with incorrect data type; to process
multiple debug flag options, and hence defined dbg_flags as u32.

Fixes the below:

drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_packet_manager_v9.c:117 pm_map_process_aldebaran() warn: maybe use && instead of &

Fixes: 0de4ec9a0353 ("drm/amdgpu: prepare map process for multi-process debug devices")
Suggested-by: Lijo Lazar <lijo.lazar@amd.com>
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mmc: sdhci_omap: Fix TI SoC dependencies

[ Upstream commit 09f164d393a6671e5ff8342ba6b3cb7fe3f20208 ]

The sdhci_omap is specific to  older TI SoCs, update the
dependencies for those SoCs and compile testing. While we're
at it update the text to reflect the wider range of
supported TI SoCS the driver now supports.

Fixes: 7d326930d352 ("mmc: sdhci-omap: Add OMAP SDHCI driver")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20231220135950.433588-2-pbrobinson@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mmc: sdhci_am654: Fix TI SoC dependencies

[ Upstream commit cb052da7f031b0d2309a4895ca236afb3b4bbf50 ]

The sdhci_am654 is specific to recent TI SoCs, update the
dependencies for those SoCs and compile testing. While we're
at it update the text to reflect the wider range of
supported TI SoCS the driver now supports.

Fixes: 41fd4caeb00b ("mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20231220135950.433588-1-pbrobinson@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: scarlett2: Add clamp() in scarlett2_mixer_ctl_put()

[ Upstream commit 04f8f053252b86c7583895c962d66747ecdc61b7 ]

Ensure the value passed to scarlett2_mixer_ctl_put() is between 0 and
SCARLETT2_MIXER_MAX_VALUE so we don't attempt to access outside
scarlett2_mixer_values[].

Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Fixes: 9e4d5c1be21f ("ALSA: usb-audio: Scarlett Gen 2 mixer interface")
Link: https://lore.kernel.org/r/3b19fb3da641b587749b85fe1daa1b4e696c0c1b.1703001053.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: scarlett2: Add missing error checks to *_ctl_get()

[ Upstream commit 50603a67daef161c78c814580d57f7f0be57167e ]

The *_ctl_get() functions which call scarlett2_update_*() were not
checking the return value. Fix to check the return value and pass to
the caller.

Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Fixes: 9e4d5c1be21f ("ALSA: usb-audio: Scarlett Gen 2 mixer interface")
Link: https://lore.kernel.org/r/32a5fdc83b05fa74e0fcdd672fbf71d75c5f0a6d.1703001053.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: scarlett2: Allow passing any output to line_out_remap()

[ Upstream commit 2190b9aea4eb92ccf3176e35c17c959e40f1a81b ]

Line outputs 3 & 4 on the Gen 3 18i8 are internally the analogue 7 and
8 outputs, and this renumbering is hidden from the user by
line_out_remap(). By allowing higher values (representing non-analogue
outputs) to be passed to line_out_remap(), repeated code from
scarlett2_mux_src_enum_ctl_get() and scarlett2_mux_src_enum_ctl_put()
can be removed.

Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/3b70267931f5994628ab27306c73cddd17b93c8f.1698342632.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: 50603a67daef ("ALSA: scarlett2: Add missing error checks to *_ctl_get()")
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: scarlett2: Add missing error check to scarlett2_usb_set_config()

[ Upstream commit ca459dfa7d4ed9098fcf13e410963be6ae9b6bf3 ]

scarlett2_usb_set_config() calls scarlett2_usb_get() but was not
checking the result. Return the error if it fails rather than
continuing with an invalid value.

Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Fixes: 9e15fae6c51a ("ALSA: usb-audio: scarlett2: Allow bit-level access to config")
Link: https://lore.kernel.org/r/def110c5c31dbdf0a7414d258838a0a31c0fab67.1703001053.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: scarlett2: Add missing error check to scarlett2_config_save()

[ Upstream commit 5f6ff6931a1c0065a55448108940371e1ac8075f ]

scarlett2_config_save() was ignoring the return value from
scarlett2_usb(). As this function is not called from user-space we
can't return the error, so call usb_audio_err() instead.

Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Fixes: 9e4d5c1be21f ("ALSA: usb-audio: Scarlett Gen 2 mixer interface")
Link: https://lore.kernel.org/r/bf0a15332d852d7825fa6da87d2a0d9c0b702053.1703001053.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: rt5645: Drop double EF20 entry from dmi_platform_data[]

[ Upstream commit 51add1687f39292af626ac3c2046f49241713273 ]

dmi_platform_data[] first contains a DMI entry matching:

   DMI_MATCH(DMI_PRODUCT_NAME, "EF20"),

and then contains an identical entry except for the match being:

   DMI_MATCH(DMI_PRODUCT_NAME, "EF20EA"),

Since these are partial (non exact) DMI matches the first match
will also match any board with "EF20EA" in their DMI product-name,
drop the second, redundant, entry.

Fixes: a4dae468cfdd ("ASoC: rt5645: Add ACPI-defined GPIO for ECS EF20 series")
Cc: Chris Chiu <chiu@endlessos.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://msgid.link/r/20231126214024.300505-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pwm: stm32: Fix enable count for clk in .probe()

[ Upstream commit 19f1016ea9600ed89bc24247c36ff5934ad94fbb ]

Make the driver take over hardware state without disabling in .probe()
and enable the clock for each enabled channel.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[ukleinek: split off from a patch that also implemented .get_state()]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 7edf7369205b ("pwm: Add driver for STM32 plaftorm")
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pwm: stm32: Use hweight32 in stm32_pwm_detect_channels

[ Upstream commit 41fa8f57c0d269243fe3bde2bce71e82c884b9ad ]

Use hweight32() to count the CCxE bits in stm32_pwm_detect_channels().
Since the return value is assigned to chip.npwm, change it to unsigned
int as well.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Stable-dep-of: 19f1016ea960 ("pwm: stm32: Fix enable count for clk in .probe()")
Signed-off-by: Sasha Levin <sashal@kernel.org>