drm/edid: fix kernel-doc parameter name mismatches

Fix the below drm/edid kernel-doc warnings:

drivers/gpu/drm/drm_edid.c:1589: warning: Function parameter or member '_edid' not described in 'drm_edid_header_is_valid'
drivers/gpu/drm/drm_edid.c:1589: warning: Excess function parameter 'raw_edid' description in 'drm_edid_header_is_valid'
drivers/gpu/drm/drm_edid.c:1737: warning: Function parameter or member '_block' not described in 'drm_edid_block_valid'
drivers/gpu/drm/drm_edid.c:1737: warning: Excess function parameter 'raw_edid' description in 'drm_edid_block_valid'
drivers/gpu/drm/drm_edid.c:2136: warning: Function parameter or member 'read_block' not described in 'drm_do_get_edid'
drivers/gpu/drm/drm_edid.c:2136: warning: Function parameter or member 'context' not described in 'drm_do_get_edid'
drivers/gpu/drm/drm_edid.c:2136: warning: Excess function parameter 'get_edid_block' description in 'drm_do_get_edid'
drivers/gpu/drm/drm_edid.c:2136: warning: Excess function parameter 'data' description in 'drm_do_get_edid'

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
References: https://lore.kernel.org/r/20220406154431.567414c3@canb.auug.org.au
References: https://lore.kernel.org/r/20220420162431.2b28ddea@canb.auug.org.au
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20220426091913.1339941-1-jani.nikula@intel.com

drm/display: Select DP helper for DRM_DP_AUX_CHARDEV and DRM_DP_CEC

The DRM_DP_AUX_CHARDEV and DRM_DP_CEC Kconfig symbols enable code that use
DP helper functions, that are only present if CONFIG_DRM_DISPLAY_DP_HELPER
is also enabled.

But these don't select the DRM_DISPLAY_DP_HELPER symbol, meaning that it
is possible to enable any of them without CONFIG_DRM_DISPLAY_DP_HELPER.

That will lead to the following linking errors with the mentioned config:

  LD      vmlinux.o
  MODPOST vmlinux.symvers
  MODINFO modules.builtin.modinfo
  GEN     modules.builtin
  LD      .tmp_vmlinux.kallsyms1
  KSYMS   .tmp_vmlinux.kallsyms1.S
  AS      .tmp_vmlinux.kallsyms1.S
  LD      .tmp_vmlinux.kallsyms2
  KSYMS   .tmp_vmlinux.kallsyms2.S
  AS      .tmp_vmlinux.kallsyms2.S
  LD      vmlinux
  SYSMAP  System.map
  SORTTAB vmlinux
  OBJCOPY arch/arm64/boot/Image
  MODPOST modules-only.symvers
ERROR: modpost: "drm_dp_dpcd_write" [drivers/gpu/drm/display/drm_display_helper.ko] undefined!
ERROR: modpost: "drm_dp_read_desc" [drivers/gpu/drm/display/drm_display_helper.ko] undefined!
ERROR: modpost: "drm_dp_dpcd_read" [drivers/gpu/drm/display/drm_display_helper.ko] undefined!
make[1]: *** [scripts/Makefile.modpost:134: modules-only.symvers] Error 1
make[1]: *** Deleting file 'modules-only.symvers'
make: *** [Makefile:1749: modules] Error 2

Besides making these symbols to select CONFIG_DRM_DISPLAY_DP_HELPER, make
them to depend on DRM_DISPLAY_HELPER, since can't be enabled without it.

Note: It seems this has been an issue for a long time but was made easier
to reproduce after the commit 1e0f66420b13 ("drm/display: Introduce a DRM
display-helper module"). Adding a Fixes: tag just to make sure that this
fix will be picked for stable once the mentioned change also lands there.

Fixes: 1e0f66420b13 ("drm/display: Introduce a DRM display-helper module")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220428082244.390859-1-javierm@redhat.com

drm/dp_mst: Lower down debug info level when receive NAK

[Why]
It's reasonable that we receive NAK while doing DP_REMOTE_DPCD_READ.
Downstream device might reply NAK with the reason and source should
react accordingly.

e.g.
1. When downstream device can't handle corresponding message in time,
it then replies NAK as reason been set as DEFER.
2. When multi-function branch-sink device doesn't enumerate virtual
DP peer devices for those multi-function down facing ports. Without
virtual DPCD, branch device might reply NAK with reason as BAD_PARAM
indicating this port can't do aux DPCD read.

It's expected result. Not an error.

[How]
Use drm_dbg_kms() to replace drm_err() when receive NAK.

Changes since v1:
* drm_dp_mst_topology.c file path changed. Folder was rename from
 'dp' to 'display'

Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
[fixed some indenting issues]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220428124944.1683680-1-Wayne.Lin@amd.com

drm/plane: Move range check for format_count earlier

While the check for format_count > 64 in __drm_universal_plane_init()
shouldn't be hit (it's a WARN_ON), in its current position it will then
leak the plane->format_types array and fail to call
drm_mode_object_unregister() leaking the modeset identifier. Move it to
the start of the function to avoid allocating those resources in the
first place.

Signed-off-by: Steven Price <steven.price@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://lore.kernel.org/dri-devel/20211203102815.38624-1-steven.price@arm.com/

malidp: Fix NULL vs IS_ERR() checking

The get_sg_table() function does not return NULL.
It returns error pointers.

Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://lore.kernel.org/dri-devel/20211213072115.18098-1-linmq006@gmail.com/

drm/format-helper: Add RGB565-to-XRGB8888 conversion

Add a format helper that converts RGB565 to XRGB8888. Use this
function in drm_fb_blit_toio(). Fixes simpledrm output for this
combination of formats.

UEFI and/or Grub will usually set 32-bit output in XRGB8888 format.
The issue can be reproduced by enabling simpledrm and requesting a
console framebuffer of different format on the kernel command line;
for example

  nomodeset video=1024x768-16

In this case, conversion helpers will display nothing on the console.
The patch makes this work by implementing the rsp conversion helpers.
It also enables odd userspace configurations, such as running Xorg
with 16-bit color depth on a 32-bit output buffer.

v2:
* use helpers for struct drm_rect (Javier)
* improve commit message (Javier)

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220425075939.30450-4-tzimmermann@suse.de

drm/format-helper: Add RGB888-to-XRGB8888 conversion

Add a format helper that converts RGB888 to XRGB8888. Use this
function in drm_fb_blit_toio(). Fixes simpledrm output for this
combination of formats.

UEFI and/or Grub will usually set 32-bit output in XRGB8888 format.
The issue can be reproduced by enabling simpledrm and requesting a
console framebuffer of different format on the kernel command line;
for example

  nomodeset video=1024x768-24

In this case, conversion helpers will display nothing on the console.
The patch makes this work by implementing the rsp conversion helpers.
It also enables odd userspace configurations, such as running Xorg
with 24-bit color depth on a 32-bit output buffer.

v2:
* use helpers for struct drm_rect (Javier)
* improve commit message (Javier)

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220425075939.30450-3-tzimmermann@suse.de

drm/format-helper: Print warning on missing format conversion

Not all possible format conversions are supported yet. Print a
warning on unsupported combinations.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220425075939.30450-2-tzimmermann@suse.de

drm/sched: use __string in tracepoints

Otherwise, ring names are marked [UNSAFE-MEMORY].

Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Cc: Rob Clark <robdclark@chromium.org>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220412204809.824491-2-olvaffe@gmail.com

drm/sched: use DECLARE_EVENT_CLASS

drm_sched_job and drm_run_job have the same prototype.

v2: rename the class from drm_sched_job_entity to drm_sched_job (Andrey)

Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Cc: Rob Clark <robdclark@chromium.org>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220412204809.824491-1-olvaffe@gmail.com

drm/nouveau/devinit/nva3-: fix returnvar.cocci warning

Fix the following coccicheck warning:
drivers/gpu/drm/nouveau/nvkm/subdev/devinit/gt215.c:71:5-12:
Unneeded variable: "disable". Return "0ULL" on line 85.

Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220425114701.7182-1-guozhengkui@vivo.com

drm/nouveau/disp/gv100: make gv100_disp_wndw and gv100_disp_wndw_mthd static

Sparse reports these issues
wndwgv100.c:120:1: warning: symbol 'gv100_disp_wndw_mthd' was not declared. Should it be static?
wndwgv100.c:140:1: warning: symbol 'gv100_disp_wndw' was not declared. Should it be static?

These variable are only used in wndwgv100.c.  Single file variables should be static.
So use static as their storage-class specifiers.

Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220425131308.158635-1-trix@redhat.com

drm/nouveau/disp/gv100: make gv100_disp_wimm static

Sparse reports this issue
wimmgv100.c:39:1: warning: symbol 'gv100_disp_wimm' was not declared. Should it be static?

This variable is only used in wimmgv100.c.  Single file variables should be static.
So use static as its storage-class specifier.

Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220425130050.1643103-1-trix@redhat.com

drm/nouveau/kms/gv100: use static for gv100_disp_core_mthd_[base|sor]

Sparse reports these issues
coregv100.c:27:1: warning: symbol 'gv100_disp_core_mthd_base' was not declared. Should it be static?
coregv100.c:43:1: warning: symbol 'gv100_disp_core_mthd_sor' was not declared. Should it be static?

These variables are only used in coregv100.c.  Single file use
variables should be static, so add static to their storage-class specifier.

Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220422185132.3163248-1-trix@redhat.com

drm/v3d: Fix null pointer dereference of pointer perfmon

In the unlikely event that pointer perfmon is null the WARN_ON return path
occurs after the pointer has already been deferenced. Fix this by only
dereferencing perfmon after it has been null checked.

Fixes: 26a4dc29b74a ("drm/v3d: Expose performance counters to userspace")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Juan A. Suarez <jasuarez@igalia.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424183512.1365683-1-colin.i.king@gmail.com

drm/sun4i: Add compatible for D1 display engine

Now that the various blocks in the D1 display engine pipeline are
supported, we can enable the overall engine.

Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-15-samuel@sholland.org

drm/sun4i: Add support for D1 TCONs

D1 has a TCON TOP, so its quirks are similar to those for the R40 TCONs.
While there are some register changes, the part of the TCON TV supported
by the driver matches the R40 quirks, so that quirks structure can be
reused. D1 has the first supported TCON LCD with a TCON TOP, so the TCON
LCD needs a new quirks structure.

D1's TCON LCD hardware supports LVDS; in fact it provides dual-link LVDS
from a single TCON. However, it comes with a brand new LVDS PHY. Since
this PHY has not been tested, leave out LVDS driver support for now.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-14-samuel@sholland.org

drm/sun4i: Add support for D1 TCON TOP

D1 has a TCON TOP with TCON TV0 and DSI, but no TCON TV1. This puts the
DSI clock name at index 1 in clock-output-names. Support this by only
incrementing the index for clocks that are actually supported.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-13-samuel@sholland.org

drm/sun4i: Add support for D1 mixers

D1 has a display engine with the usual pair of mixers, albeit with
relatively few layers. In fact, D1 appears to be the first SoC to have
a mixer without any UI layers. Add support for these new variants.

Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-12-samuel@sholland.org

drm/sun4i: csc: Add support for the new MMIO layout

D1 changes the MMIO offsets for the CSC blocks in the first mixer. The
mixers' ccsc property is used as an index into the ccsc_base array. Use
an enumeration to describe this index, and add the new set of offsets.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-11-samuel@sholland.org

drm/sun4i: Allow VI layers to be primary planes

D1's mixer 1 has no UI layers, only a single VI layer. That means the
mixer can only be used if the primary plane comes from this VI layer.
Add the code to handle this case.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-10-samuel@sholland.org

sun4i/drm: sun8i: use mode_set engine callback

Newly introduced mode_set callback in engine structure is a much better
place for setting mixer output size and interlace mode for the following
reasons:
1. Aforementioned properties change only when mode changes, so it's
   enough to be set only once per mode set. Currently it's done whenever
   properties of primary plane are changed.
2. It's assumed that primary plane will always cover whole screen. While
   this is true most of the time, it's not always. DE2/3 planes are
   universal and mostly equal in functionality. There is no reason to
   add artificial limitation to primary planes.
3. The current code only works for UI layers, but some mixers do not
   have any UI layers.

Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
[Samuel: update commit message]
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-9-samuel@sholland.org

sun4i/drm: backend: use mode_set engine callback

Newly introduced mode_set callback in engine structure is a much better
place for setting backend output size and interlace mode for following
reasons:
1. Aforementioned properties change only when mode changes, so it's
   enough to be set only once per mode set. Currently it's done whenever
   properties of primary plane are changed.
2. It's assumed that primary plane will always cover whole screen. While
   this is true most of the time, it's not always. Planes are universal.
   There is no reason to add artificial limitation to primary plane.

Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
[Samuel: drop unused 'interlaced' variable]
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-8-samuel@sholland.org

sun4i/drm: engine: Add mode_set callback

This optional callback is useful for setting properties which depends
only on current mode. Such properties are width, height and interlaced
output.

These properties are currently set in update layer callback for primary
plane which is less than ideal. More about that in follow up patches,
which will migrate that code to this newly defined callback.

Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-7-samuel@sholland.org

drm/sun4i: Allow building the driver on RISC-V

Allwinner D1 is a RISC-V SoC which contains a DE 2.0 engine. Let's
remove the dependency on a specific CPU architecture, so the driver can
be built wherever ARCH_SUNXI is selected.

Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-6-samuel@sholland.org

drm/sun4i: hdmi: Use more portable I/O helpers

readsb/writesb are unavailable on some architectures. In preparation for
removing the Kconfig architecture dependency, switch to the equivalent
but more portable ioread/write8_rep helpers.

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-5-samuel@sholland.org

dt-bindings: display: Add D1 display engine compatibles

Allwinner D1 contains a display engine 2.0. It features two mixers, a
TCON TOP (with DSI and HDMI), one TCON LCD, and one TCON TV.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-3-samuel@sholland.org

dt-bindings: display: Separate clock item lists by compatible

So far, the binding and driver have relied on the fact that the H6
clocks are both a prefix and a subset of the R40 clocks. This allows
them to share the clocks/clock-names items and the clock-output-names
order between the hardware variants.

However, the D1 hardware has TCON TV0 and DSI, but no TCON TV1. This
cannot be supported by the existing scheme because it puts a gap in the
middle of the item lists. To prepare for adding D1 support, use separate
lists for variants with different combinations of clocks.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-2-samuel@sholland.org

drm/bridge: tc358762: drop connector field

The tc358762.connector field is unused. Remove it to save space.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220426011359.2861224-1-dmitry.baryshkov@linaro.org

drm/ssd130x: Make ssd130x_remove() return void

This function returns zero unconditionally, so there isn't any benefit
of returning a value. Make it return void to be able to see at a glance
that the return value of ssd130x_i2c_remove() is always zero.

This patch is a preparation for making i2c remove callbacks return void.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220425192306.59800-1-u.kleine-koenig@pengutronix.de

drm: mxsfb: Obtain bus flags from bridge state

In case the MXSFB is connected to a bridge, attempt to obtain bus flags
from that bridge state too. The bus flags may specify e.g. the DE signal
polarity.

Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexander Stein <alexander.stein@ew.tq-group.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Robby Cai <robby.cai@nxp.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stefan Agner <stefan@agner.ch>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220417021011.337066-1-marex@denx.de

drm: mxsfb: Reorder mxsfb_crtc_mode_set_nofb()

Reorder mxsfb_crtc_mode_set_nofb() such that all functions which perform
register IO are called from one single location in this function. This is
a clean up. No functional change.

Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexander Stein <alexander.stein@ew.tq-group.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Robby Cai <robby.cai@nxp.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stefan Agner <stefan@agner.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220417020800.336675-4-marex@denx.de

drm: mxsfb: Factor out mxsfb_set_mode()

Pull mode registers programming from mxsfb_enable_controller() into
dedicated function mxsfb_set_mode(). This is a clean up. No functional
change.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexander Stein <alexander.stein@ew.tq-group.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Robby Cai <robby.cai@nxp.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stefan Agner <stefan@agner.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220417020800.336675-3-marex@denx.de

drm: mxsfb: Replace mxsfb_get_fb_paddr() with drm_fb_cma_get_gem_addr()

Replace mxsfb_get_fb_paddr() with drm_fb_cma_get_gem_addr() to correctly handle
FB offset.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexander Stein <alexander.stein@ew.tq-group.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Robby Cai <robby.cai@nxp.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stefan Agner <stefan@agner.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220417020800.336675-2-marex@denx.de

drm: mxsfb: Wrap FIFO reset and comments into mxsfb_reset_block()

Wrap FIFO reset and comments into mxsfb_reset_block(), this is a clean up.
No functional change.

Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexander Stein <alexander.stein@ew.tq-group.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Robby Cai <robby.cai@nxp.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stefan Agner <stefan@agner.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220417020800.336675-1-marex@denx.de

drm/display: Move SCDC helpers into display-helper library

SCDC is the Status and Control Data Channel for HDMI. Move the SCDC
helpers into display/ and split the header into files for core and
helpers. Update all affected drivers. No functional changes.

To avoid the proliferation of Kconfig options, SCDC is part of DRM's
support for HDMI. If necessary, a new option could make SCDC an
independent feature.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-9-tzimmermann@suse.de

drm/display: Move HDMI helpers into display-helper module

Move DRM's HMDI helpers into the display/ subdirectoy and add it
to DRM's display helpers. Update all affected drivers. No functional
changes.

The HDMI helpers were implemented in the EDID and connector code, but
are actually unrelated. With the move to the display-helper library, we
can remove the dependency on drm_edid.{c,h} in some driver's HDMI source
files.

Several of the HDMI helpers remain in EDID code because both share parts
of their implementation internally. With better refractoring of the EDID
code, those HDMI helpers could be moved into the display-helper library
as well.

v3:
* fix Kconfig dependencies (Javier)
v2:
* reduce HDMI helpers to avoid exporting functions (Jani)
* fix include statements (Jani, Javier)
* update Kconfig symbols

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-8-tzimmermann@suse.de

drm/display: Move HDCP helpers into display-helper module

Move DRM's HDCP helper library into the display/ subdirectory and add
it to DRM's display helpers. Split the header file into core and helpers.
Update all affected drivers. No functional changes.

v3:
* fix Kconfig dependencies
v2:
* fix include statements (Jani, Javier)
* update Kconfig symbols

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-7-tzimmermann@suse.de

drm/display: Move DSC header and helpers into display-helper module

DSC is the Display Stream Compression standard for DisplayPort. Move
the DSC code into display/ and split the header into files for protocol
core and DRM helpers. Adapt all users of the code. No functional
changes.

To avoid the proliferation of Kconfig options, DSC is part of DRM's
support for DisplayPort. If necessary, a new option could make DSC an
independent feature.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-6-tzimmermann@suse.de

drm/display: Split DisplayPort header into core and helper

Move DisplayPort protocol constants and structures into the new
header drm_dp.h, which can be used by DRM core components. The
existing header drm_dp_helper.h now only contains helper code for
graphics drivers. No functional changes.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-5-tzimmermann@suse.de

drm/display: Introduce a DRM display-helper module

Replace the DP-helper module with a display-helper module. The
support for DisplayPort becomes an internal option that drivers
have to select. Update all related Kconfig and Makefile rules.

Besides the existing code for DisplayPort, the new module will
contain helpers for other video-output standards, such as HDMI.
Drivers will have to select their required video-output helpers.

Linking all display-related code into a single module avoids the
proliferation of small kernel modules.

The module parameters drm_dp_cec_unregister_delay, dp_aux_i2c_speed_khz,
and dp_aux_i2c_transfer_size are moving from the drm_dp_helper namespace
to drm_display_helper.

v2:
* mention module parameters in commit message (Javier)
* distiguish between display module and DP support in Kconfig
* update Makefile rules for DP helpers
* move Kconfig rules into separate file under display/

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-4-tzimmermann@suse.de

drm: Rename dp/ to display/

Rename dp/ to display/ to account for additional display-related
helpers, such as HDMI. Update all related include statements. No
functional changes.

Various drivers, such as i915 and amdgpu, use similar naming scheme
by putting code for video-output standards into a local display/
directory. The new directory's name is aligned with this convention.

v2:
* update commit message (Javier)

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-3-tzimmermann@suse.de

drm: Put related statements next to each other in Makefile

Give the Makefile a bit more structure by putting rules for core,
helpers, drivers, etc next to each other.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-2-tzimmermann@suse.de

drm/tilcdc: fix typos in comment

Fix typos in comment.

Signed-off-by: Chunguang Xu <brookxu@tencent.com>
Signed-off-by: Jyri Sarha <jyri.sarha@iki.fi>
Link: https://patchwork.freedesktop.org/patch/msgid/1650625751-32137-1-git-send-email-brookxu.cn@gmail.com

drm/panel: simple: Add missing bus flags for Innolux G070Y2-L01

The DE signal is active high on this display, fill in the missing bus_flags.
This aligns panel_desc with its display_timing .

Fixes: a5d2ade627dca ("drm/panel: simple: Add support for Innolux G070Y2-L01")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Fritz <chf.fritz@googlemail.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220406093627.18011-1-marex@denx.de

drm/panel: lvds: Drop now redundant width-mm and height-mm check

The check for mandatory DT properties width-mm and height-mm is now
part of of_get_drm_panel_display_mode(), drop the redundant check
from this driver.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dmitry Osipenko <digetx@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220411004728.68203-2-marex@denx.de

drm/modes: Make width-mm/height-mm check in of_get_drm_panel_display_mode() mandatory

All users of this function require width-mm/height-mm DT property to be
present per their DT bindings, make width-mm/height-mm check mandatory.
It is generally a good idea to specify panel dimensions, so userspace
can configure e.g. scaling accordingly.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dmitry Osipenko <digetx@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220411004728.68203-1-marex@denx.de

drm/panel: simple: Add DataImage FG040346DSSWBG04 panel support

Add DataImage FG040346DSSWBG04 4.3" 480x272 TFT LCD 24bit DPI panel
support.

Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220422102242.18959-2-marex@denx.de

dt-bindings: display: simple: Add DataImage FG040346DSSWBG04 compatible string

Add DataImage FG040346DSSWBG04 4.3" 480x272 TFT LCD 24bit DPI panel
compatible string.

Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: devicetree@vger.kernel.org
To: dri-devel@lists.freedesktop.org
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220422102242.18959-1-marex@denx.de

drm/vmwgfx: Reserve fence slots on buffer objects in cotables

The buffer objects created by cotables were missing fence reservations.
They are created from vmw_validation_res_validate which makes them miss
the ttm_eu_reserve_buffers which is called from vmw_validation_bo_reserve.

Cotables are the only resources which create a buffer object in the
create callback so make sure the code also reserves the slots.

Signed-off-by: Zack Rusin <zackr@vmware.com>
Co-developed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Fixes: c8d4c18bfbc4 ("dma-buf/drivers: make reserving a shared slot mandatory v4")
Link: https://patchwork.freedesktop.org/patch/msgid/20220422161342.1142584-1-zack@kde.org

drm/nouveau/gsp: change gv100_gsp from global to static

Smatch reports this issue
gv100.c:46:1: warning: symbol 'gv100_gsp' was not declared. Should it be static?

gv100_gsp is only used in gv100.c so change its
storage-class specifier to static.

Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421133028.724954-1-trix@redhat.com

drm/bridge: Fix it6505 Kconfig DRM_DP_AUX_BUS dependency

it6505 depends on DRM_DP_AUX_BUS, the kconfig for it6505 should
reflect this dependency using 'select'.

Fixes: b5c84a9edcd4 ("drm/bridge: add it6505 driver")
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421131415.1289469-1-robert.foss@linaro.org

drm/doc: Add sections about tiny drivers and external refs to intro page

Learning about the DRM subsystem could be quite overwhelming for newcomers
but there are lots of useful talks, slides and articles available that can
help to understand the needed concepts and ease the learning curve.

There are also simple DRM drivers that can be used as example about how a
DRM driver should look like.

Add sections to the introduction page, that contains references to these.

Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220420072411.15104-1-javierm@redhat.com

drm/sun4i: hdmi: Replace drm_detect_hdmi_monitor() with is_hdmi

Once EDID is parsed, the monitor HDMI support information is available
through drm_display_info.is_hdmi.

This driver calls drm_detect_hdmi_monitor() to receive the same
information and stores its own cached value, which is less efficient.

Avoid calling drm_detect_hdmi_monitor() and use drm_display_info.is_hdmi
instead and also remove sun4i_hdmi.hdmi_monitor as it is no longer
necessary.

Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421170725.903361-6-jose.exposito89@gmail.com

drm: bridge: dw_hdmi: Audio: fix returnvar.cocci warnings

drivers/gpu/drm/bridge/synopsys/dw-hdmi-gp-audio.c:80:5-8: Unneeded variable: "ret". Return "0" on line 94
drivers/gpu/drm/bridge/synopsys/dw-hdmi-gp-audio.c:105:5-8: Unneeded variable: "ret". Return "0" on line 112

 Remove unneeded variable used to store return value.

Generated by: scripts/coccinelle/misc/returnvar.cocci

CC: Sandor Yu <Sandor.yu@nxp.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Reviewed-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YmFzutFV/iDyEQF2@dd18de969aa6

drm/ttm: use kvcalloc() instead of kvmalloc_array() in ttm_tt v2

simplify programming with existing functions.

v2 (chk): minimal coding style cleanup

Signed-off-by: Yang Wang <KevinYang.Wang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421123442.1834102-1-KevinYang.Wang@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>

drm/bridge: Fix error handling in analogix_dp_probe

In the error handling path, the clk_prepare_enable() function
call should be balanced by a corresponding 'clk_disable_unprepare()'
call, as already done in the remove function.

Fixes: 3424e3a4f844 ("drm: bridge: analogix/dp: split exynos dp driver to bridge directory")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220420011644.25730-1-linmq006@gmail.com

drm/amdgpu: remove pointless ttm_eu usage from DM

We just need to reserve one BO here, no need for using ttm_eu to reserve
multiple BOs.

Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419141915.122157-2-christian.koenig@amd.com

drm/amdgpu: remove pointless ttm_eu usage from vkms

We just need to reserve one BO here, no need for using ttm_eu to reserve
multiple BOs.

Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419141915.122157-1-christian.koenig@amd.com

drm/vc4: hdmi: Remove vc4_hdmi_encoder

The vc4_hdmi_encoder struct was used exclusively to cache the value
returned by drm_detect_hdmi_monitor() in order to avoid calling it
multiple times.

Now that drm_detect_hdmi_monitor() has been replaced with
drm_display_info.is_hdmi, there is no need to have an extra struct.

Remove vc4_hdmi_encoder.

Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220420114500.187664-3-jose.exposito89@gmail.com

drm/vc4: hdmi: Replace drm_detect_hdmi_monitor() with is_hdmi

Once EDID is parsed, the monitor HDMI support information is cached in
drm_display_info.is_hdmi by drm_parse_hdmi_vsdb_video().

This driver calls drm_detect_hdmi_monitor() to receive the same
information and stores its own cached value in
vc4_hdmi_encoder.hdmi_monitor, which is less efficient.

Avoid calling drm_detect_hdmi_monitor() and use drm_display_info.is_hdmi
instead. This also allows to remove vc4_hdmi_encoder.hdmi_monitor.

drm_detect_hdmi_monitor() is called in vc4_hdmi_connector_detect() and
vc4_hdmi_connector_get_modes(). In both cases it is safe to rely on
drm_display_info.is_hdmi as shown by ftrace:

$ sudo trace-cmd record -p function_graph -l "vc4_hdmi_*" -l "drm_*"

vc4_hdmi_connector_detect:

    vc4_hdmi_connector_detect() {
      drm_get_edid() {
        drm_connector_update_edid_property() {
          drm_add_display_info() {
            drm_reset_display_info();
            drm_for_each_detailed_block.part.0();
            drm_parse_cea_ext() {
              drm_find_cea_extension();
              drm_parse_hdmi_vsdb_video();
              /* drm_display_info.is_hdmi is cached here */
            }
          }
        }
      }
      /* drm_display_info.is_hdmi is used here */
    }

vc4_hdmi_connector_get_modes:

    vc4_hdmi_connector_get_modes() {
      drm_get_edid() {
        drm_connector_update_edid_property() {
          drm_add_display_info() {
            drm_reset_display_info();
            drm_for_each_detailed_block.part.0();
            drm_parse_cea_ext() {
              drm_find_cea_extension();
              drm_parse_hdmi_vsdb_video();
              /* drm_display_info.is_hdmi is cached here */
            }
          }
        }
      }
      /* drm_display_info.is_hdmi is used here */
      drm_connector_update_edid_property();
    }

Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220420114500.187664-2-jose.exposito89@gmail.com

drm/radeon: Use TTM builtin resource manager debugfs code

Switch to using the TTM resource manager debugfs helpers. The
functionality is largely the same.
The TTM resource managers need to stay valid for as long as the
drm debugfs_root is valid.

Signed-off-by: Zack Rusin <zackr@vmware.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20220412033526.369115-6-zack@kde.org
Reviewed-by: Christian König <christian.koenig@amd.com>

drm/qxl: Use TTM builtin resource manager debugfs code

Switch to using the TTM resource manager debugfs helpers. The
functionality is largely the same.
The TTM resource managers need to stay valid for as long as the
drm debugfs_root is valid.

Signed-off-by: Zack Rusin <zackr@vmware.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: virtualization@lists.linux-foundation.org
Cc: spice-devel@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20220412033526.369115-5-zack@kde.org
Reviewed-by: Christian König <christian.koenig@amd.com>

drm/amdgpu: Use TTM builtin resource manager debugfs code

Switch to using the TTM resource manager debugfs helpers. It's
exactly the same functionality but the debugfs code is shared with
other drivers.

The TTM resource managers need to stay valid for as long as the
drm debugfs_root is valid.

Signed-off-by: Zack Rusin <zackr@vmware.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Nirmoy Das <nirmoy.das@amd.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: amd-gfx@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20220412033526.369115-4-zack@kde.org
Reviewed-by: Christian König <christian.koenig@amd.com>

drm/vmwgfx: Add debugfs entries for various ttm resource managers

Use the newly added TTM's ability to automatically create debugfs entries
for specified placements. This creates debugfs files that can be read to
get information about various TTM resource managers which are used by
vmwgfx.

Signed-off-by: Zack Rusin <zackr@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220412033526.369115-3-zack@kde.org
Reviewed-by: Christian König <christian.koenig@amd.com>

drm/ttm: Add common debugfs code for resource managers

Drivers duplicate the code required to add debugfs entries for various
ttm resource managers. To fix it add common TTM resource manager debugfs
code that each driver can reuse.

Specific resource managers can overwrite
ttm_resource_manager_func::debug to get more information from those
debugfs entries.

Signed-off-by: Zack Rusin <zackr@vmware.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220412033526.369115-2-zack@kde.org
Reviewed-by: Christian König <christian.koenig@amd.com>

drm/solomon: Add SSD130x OLED displays SPI support

The ssd130x driver only provides the core support for these devices but it
does not have any bus transport logic. Add a driver to interface over SPI.

There is a difference in the communication protocol when using 4-wire SPI
instead of I2C. For the latter, a control byte that contains a D/C# field
has to be sent. This field tells the controller whether the data has to be
written to the command register or to the graphics display data memory.

But for 4-wire SPI that control byte is not used, instead a real D/C# line
must be pulled HIGH for commands data and LOW for graphics display data.

For this reason the standard SPI regmap can't be used and a custom .write
bus handler is needed.

Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419214824.335075-6-javierm@redhat.com

drm/solomon: Move device info from ssd130x-i2c to the core driver

These are declared in the ssd130x-i2c transport driver but the information
is not I2C specific, and could be used by other SSD130x transport drivers.

Move them to the ssd130x core driver and just set the OF device entries to
an ID that could be used to lookup the correct device info from an array.

While being there, also move the SSD130X_DATA and SSD130X_COMMAND control
bytes. Since even though they are used by the I2C interface, they could
also be useful for other transport protocols such as SPI.

Suggested-by: Chen-Yu Tsai <wens@kernel.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419214824.335075-5-javierm@redhat.com

drm/solomon: Add ssd130x new compatible strings and deprecate old ones.

The current compatible strings for SSD130x I2C controllers contain an "fb"
and "-i2c" suffixes. These have been deprecated and more correct ones were
added, that don't encode a subsystem or bus used to interface the devices.

Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419214824.335075-4-javierm@redhat.com

dt-bindings: display: ssd1307fb: Extend schema for SPI controllers

The Solomon SSD130x OLED displays can either have an I2C or SPI interface,
add to the schema the properties and examples for OLED devices under SPI.

Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419214824.335075-3-javierm@redhat.com

dt-bindings: display: ssd1307fb: Deprecate "-i2c" compatible strings

The current compatible strings for SSD130x I2C controllers contain both an
"fb" and "-i2c" suffixes. It seems to indicate that are for a fbdev driver
and also that are for devices that can be accessed over an I2C bus.

But a DT is supposed to describe the hardware and not Linux implementation
details. So let's deprecate those compatible strings and add new ones that
only contain the vendor and device name, without any of these suffixes.

These will just describe the device and can be matched by both I2C and SPI
DRM drivers. The required properties should still be enforced for old ones.

While being there, just drop the "sinowealth,sh1106-i2c" compatible string
since that was never present in a released Linux version.

Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419214824.335075-2-javierm@redhat.com

fbdev: Warn in hot-unplug workaround for framebuffers without device

A workaround makes fbdev hot-unplugging work for framebuffers without
device. The only user for this feature was offb. As each OF framebuffer
now has an associated platform device, the workaround hould no longer
be triggered. Update it with a warning and rewrite the comment. Fbdev
drivers that trigger the hot-unplug workaround really need to be fixed.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Suggested-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419100405.12600-3-tzimmermann@suse.de

of: Create platform devices for OF framebuffers

Create a platform device for each OF-declared framebuffer and have
offb bind to these devices. Allows for real hot-unplugging and other
drivers besides offb.

Originally, offb created framebuffer devices while initializing its
module by parsing the OF device tree. No actual Linux device was set
up. This tied OF framebuffers to offb and makes writing other drivers
for the OF framebuffers complicated. The absence of a Linux device
further prevented real hot-unplugging. Adding a distinct platform
device for each OF framebuffer solves both problems. Specifically, a
DRM driver can now provide graphics output for modern userspace.

Some of the offb init code is now located in the OF initialization.
There's now also an implementation of of_platform_default_populate_init(),
which was missing before. The OF side creates different devices for
either OF display nodes or BootX displays as they require different
handling by the driver. The offb drivers picks up each type of device
and runs the appropriate fbdev initialization.

Tested with OF display nodes on qemu's ppc64le target.

v3:
* declare variable 'node' with function scope (Rob)
v2:
* run PPC code as part of existing initialization (Rob)
* add a few more error warnings (Javier)

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419100405.12600-2-tzimmermann@suse.de

drm/gma500: fix a potential repeat execution in psb_driver_load

Instead of exiting the loop as expected when an entry is found, the
list_for_each_entry() continues until the traversal is complete. To
avoid potential executing 'ret = gma_backlight_init(dev);' repeatly,
goto outside the loop when found entry by replacing switch/case with
if statement.

Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
[Fixed indentation]
Link: https://patchwork.freedesktop.org/patch/msgid/20220413051105.5612-1-xiam0nd.tong@gmail.com

drm: bridge: icn6211: Add DSI lane count DT property parsing

The driver currently hard-codes DSI lane count to two, however the chip
is capable of operating in 1..4 DSI lanes mode. Parse 'data-lanes' DT
property and program the result into DSI_CTRL register.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220407185617.179573-2-marex@denx.de

dt-bindings: display: bridge: icn6211: Document DSI data-lanes property

It is necessary to specify the number of connected/used DSI data lanes when
using the DSI input port of this bridge. Document the 'data-lanes' property
of the DSI input port.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: devicetree@vger.kernel.org
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220407185617.179573-1-marex@denx.de

drm/bridge: anx7625: Use uint8 for lane-swing arrays

As defined in the anx7625 dt-binding, the analogix,lane0-swing and
analogix,lane1-swing properties are uint8 arrays. Yet, the driver was
reading the array as if it were of uint32 and masking to 8-bit before
writing to the registers. This means that a devicetree written in
accordance to the dt-binding would have its values incorrectly parsed.

Fix the issue by reading the array as uint8 and storing them as uint8
internally, so that we can also drop the masking when writing the
registers.

Fixes: fd0310b6fe7d ("drm/bridge: anx7625: add MIPI DPI input feature")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220408013034.673418-1-nfraprado@collabora.com

drm: bridge: dw_hdmi: Audio: Add General Parallel Audio (GPA) driver

General Parallel Audio (GPA) interface is one of the supported
audio interface for synopsys HDMI module, which has verified for
i.MX8MPlus platform.
This is initial version for GPA.

Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/f21ba3e8c4d9d028ac74c6f3c588ddbffe739399.1649989179.git.Sandor.yu@nxp.com

drm: bridge: dw_hdmi: add reset function for PHY GEN1

PHY reset register(MC_PHYRSTZ) active high reset control for PHY GEN2,
and active low reset control for PHY GEN1.

Rename function dw_hdmi_phy_reset to dw_hdmi_phy_gen2_reset.
Add dw_hdmi_phy_gen1_reset function for PHY GEN1.

Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/e0b3be2d63fe3e95246fb8b8b0dcd57415b29e04.1649989179.git.Sandor.yu@nxp.com

drm: bridge: dw_hdmi: Enable GCP only for Deep Color

HDMI1.4b specification section 6.5.3:
Source shall only send GCPs with non-zero CD to sinks
that indicate support for Deep Color.

DW HDMI GCP default enabled, but only transmit CD
and do not handle AVMUTE, PP norDefault_Phase (yet).
Disable Auto GCP when 24-bit color for sinks that not support Deep Color.

Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/78fa41e4fb3d3d53354034bc221fcf870dbac617.1649989179.git.Sandor.yu@nxp.com

drm: bridge: dw_hdmi: default enable workaround to clear the overflow

i.MX8MPlus (v2.13a) has verified need the workaround to clear the
overflow with one iteration.
Only i.MX6Q(v1.30a) need the workaround with 4 iterations,
the others versions later than v1.3a have been identified as needing
the workaround with a single iteration.

Default enable the workaround with one iteration for all versions
later than v1.30a.

Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/561951005a85574dcdd108e5d6a3a87df930ea3d.1649989179.git.Sandor.yu@nxp.com

drm: bridge: panel: Register connector if DRM device is already registered

If panel_bridge_attach() happens after DRM device registration, the
created connector will not be registered by the DRM core anymore. Fix
this by registering it explicitly in such case.

This fixes the following issue observed on Samsung Exynos4210-based Trats
board with a DSI panel (the panel driver is registered after the Exynos DRM
component device is bound):

$ ./modetest -c -Mexynos
could not get connector 56: No such file or directory
Segmentation fault

While touching this, move the connector reset() call also under the DRM
device registered check, because otherwise it is not really needed.

Fixes: 934aef885f9d ("drm: bridge: panel: Reset the connector state pointer")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419091422.4255-1-m.szyprowski@samsung.com

drm: bridge: adv7511: Enable DRM_BRIDGE_OP_HPD based on HPD interrupt

Connector detection using poll method won't work in case of bridge
attached to the encoder with the flag DRM_BRIDGE_ATTACH_NO_CONNECTOR, as
the code defaults to HPD.

Enable DRM_BRIDGE_OP_HPD based on HPD interrupt availability, so that
it will fall back to polling, if HPD is not available.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419142453.48839-1-biju.das.jz@bp.renesas.com

drm/bridge: lt9211: Add Lontium LT9211 bridge driver

Add driver for Lontium LT9211 Single/Dual-Link DSI/LVDS or Single DPI to
Single-link/Dual-Link DSI/LVDS or Single DPI bridge. This chip is highly
capable at converting formats, but sadly it is also highly undocumented.

This driver is written without any documentation from Lontium and based
only on shreds of information available in various obscure example codes,
hence long runs of unknown register patches and lengthy delays in various
places. Whichever register meaning could be divined from its behavior has
at least a comment around it.

Currently the only mode tested is Single-link DSI to Single-link LVDS.
Dual-link LVDS might work as well, the register programming is in place,
but is untested.

Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419143958.94873-2-marex@denx.de

dt-bindings: display: bridge: lt9211: Add Lontium LT9211 bridge driver

Add bindings for Lontium LT9211 Single/Dual-Link DSI/LVDS or Single DPI to
Single-link/Dual-Link DSI/LVDS or Single DPI bridge. This chip is highly
capable at converting formats, but sadly it is also highly undocumented.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: devicetree@vger.kernel.org
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419143958.94873-1-marex@denx.de

drm/bridge: anx7625: Fill in empty ELD when no connector

Speaker may share I2S with DP and .get_eld callback will be called when
speaker is playing. When HDMI wans't connected, the connector will be
null. Instead of return an error, fill in empty ELD.

Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414090003.1806535-1-hsinyi@chromium.org

drm/tidss: Soft Reset DISPC on startup

Soft reset the display subsystem controller on startup and wait for
the reset to complete. This helps the scenario where display was
already in use by some other core before the linux was booted.

Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220314113739.18000-1-devarsht@ti.com

Merge drm/drm-next into drm-misc-next

drm/drm-next has a build fix for the NewVision NV3052C panel
(drivers/gpu/drm/panel/panel-newvision-nv3052c.c), which needs to be
merged back to drm-misc-next, as it was failing to build there.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>

drm/nouveau/gr/gf100-: change gf108_gr_fwif from global to static

Smatch reports this issue
gf108.c:147:1: warning: symbol 'gf108_gr_fwif'
  was not declared. Should it be static?

gf108_gr_fwif is only used in gf108.c.  Single
file variables should not be global so change
gf108_gr_fwif's storage-class specifier to static.

Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220418152810.3280502-1-trix@redhat.com

drm/nouveau: change base917c_format from global to static

Smatch reports this issue
base917c.c:26:1: warning: symbol 'base917c_format'
  was not declared. Should it be static?

base917c_format is only used in base917.c.  Single
file variables should not be global so change
base917c_format's storage-class specifier to static.

Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220418141842.296386-1-trix@redhat.com

Revert "video: fbdev: fbmem: fix pointer reference to null device field"

This reverts commit d6cd978f7e6b6f6895f8d0c4ce6e5d2c8e979afe.
It has been solved differently already.

Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220210065824.368355-1-zhouzhouyi@gmail.com

video: fbdev: fbmem: fix pointer reference to null device field

In function do_remove_conflicting_framebuffers, if device is NULL, there
will be null pointer reference. The patch add a check to the if expression.

Signed-off-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220210065824.368355-1-zhouzhouyi@gmail.com

fbcon: replace snprintf in show functions with sysfs_emit

Use sysfs_emit instead of scnprintf or sprintf.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Guang <yang.guang5@zte.com.cn>
Signed-off-by: Helge Deller <deller@gmx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/0cb7ca73d9cd7162988a22a24cd18bbcd3d8bb27.1638156341.git.yang.guang5@zte.com.cn

drm/dp: Factor out a function to probe a DPCD address

Factor out from drm_dp_dpcd_read() a function to probe a DPCD address
with a 1-byte read access. This will be needed by the next patch doing a
read from an LTTPR address, which must happen without the preceding
wake-up read in drm_dp_dpcd_read().

While at it add tracing for the 1 byte read even if the read was
successful.

v2: Add a probe function instead of exporting drm_dp_dpcd_access(). (Jani)
v3: Add tracing for the 1-byte read even if the read was successful. (Khaled)

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220411132539.984647-1-imre.deak@intel.com

drm/edid: add EDID block count and size helpers

Add some helpers to figure out the EDID extension block count, block
count, size, pointers to blocks.

Unfortunately, we'll need to cast away the const in a few places where
we actually need to access the data.

v3: fix (!edid_extension_block_count(edid) == 0) (kernel test robot)

v2: fix s/j/i/ introduced in a rebase

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/dc7b0850293d837439fb3914c8a9d81e39018b4b.1649685475.git.jani.nikula@intel.com

drm/edid: add single point of return to drm_do_get_edid()

This will be useful in the future. Use fail label for fail exit.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8e564e9415baa4dc9dc3127e4200b2618a8a3ba0.1649685475.git.jani.nikula@intel.com

drm/edid: drop extra local var

We don't need override as a variable for anything.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/4d249173b34758e1d6c4a74eb98518d180f0a8ae.1649685475.git.jani.nikula@intel.com

drm/edid: convert extension block read to EDID block read helper

Use the EDID block read helper also for extension block reads, making
edid_block_read() the only place with the read retry logic.

Note: We observe that drm_do_get_edid() does not use invalid extension
blocks to flag the EDID as corrupt.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a6328b898db40235b85ad4635374bc0768b5a970.1649685475.git.jani.nikula@intel.com

drm/edid: use EDID block read helper in drm_do_get_edid()

Convert drm_do_get_edit() from the base block read helper to the generic
block read helper. There's quite a bit going on here, as the corrupt and
null EDID information is moved back to the caller. As we see, they were
not all that clear to begin with, and this change underlines that.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3bcf98453770757ee93386da0cfbc6552d42a312.1649685475.git.jani.nikula@intel.com

drm/edid: abstract an EDID block read helper

We have an abstraction for the EDID base block read, yet duplicating the
retries and error handling for extension block reads. Introduce a more
generic EDID block read helper.

Switch to the helper piecemeal, starting with drm_edid_get_panel_id(),
which doesn't need or have access to the connector anyway.

The subtle change is switching from drm_edid_block_valid() to
edid_block_check(). We also status print once, not for every attempt.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/47560f7530e4a7b32b56cb9038178244fe30a4af.1649685475.git.jani.nikula@intel.com