David S. Miller [Tue, 10 Aug 2010 07:06:58 +0000 (00:06 -0700)]
farsync: Fix compile warnings.
drivers/net/wan/farsync.c: In function 'fst_intr_rx':
drivers/net/wan/farsync.c:1312: warning: cast to pointer from integer of different size
drivers/net/wan/farsync.c: In function 'do_bottom_half_tx':
drivers/net/wan/farsync.c:1407: warning: cast to pointer from integer of different size
The "skb" and "mem" arguments being passed here are DMA addresses
being programmed into the hardware registers, so pass them as the type
that they actually are. And use the correct printf formatting in
debug logging statements for these things to match the type change.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher [Sun, 8 Aug 2010 15:54:31 +0000 (15:54 +0000)]
igbvf.txt: Add igbvf Documentation
Adds documentation for the igbvf (igb virtual function driver).
v2:
- Removed trailing white space
- Removed Ethtool version info
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher [Sun, 8 Aug 2010 15:54:11 +0000 (15:54 +0000)]
igb.txt: Add igb documentation
Add documentation for the igb networking driver.
v2:
- Removed trailing white space
- Removed Ethtool version info
- Removed LRO kernel version info
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher [Sun, 8 Aug 2010 16:02:31 +0000 (16:02 +0000)]
e100/e1000*/igb*/ixgb*: Add missing read memory barrier
Based on patches from Sonny Rao and Milton Miller...
Combined the patches to fix up clean_tx_irq and clean_rx_irq.
The PowerPC architecture does not require loads to independent bytes
to be ordered without adding an explicit barrier.
In ixgbe_clean_rx_irq we load the status bit then load the packet data.
With packet split disabled if these loads go out of order we get a
stale packet, but we will notice the bad sequence numbers and drop it.
The problem occurs with packet split enabled where the TCP/IP header
and data are in different descriptors. If the reads go out of order
we may have data that doesn't match the TCP/IP header. Since we use
hardware checksumming this bad data is never verified and it makes it
all the way to the application.
This bug was found during stress testing and adding this barrier has
been shown to fix it. The bug can manifest as a data integrity issue
(bad payload data) or as a BUG in skb_pull().
This was a nasty bug to hunt down, if people agree with the fix I think
it's a candidate for stable.
Previously Submitted to e1000-devel only for ixgbe
http://marc.info/?l=e1000-devel&m=
126593062701537&w=3
We've now seen this problem hit with other device drivers (e1000e mostly)
So I'm resubmitting with fixes for other Intel Device Drivers with
similar issues.
CC: Milton Miller <miltonm@bga.com>
CC: Anton Blanchard <anton@samba.org>
CC: Sonny Rao <sonnyrao@us.ibm.com>
CC: stable <stable@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Sun, 8 Aug 2010 15:46:15 +0000 (15:46 +0000)]
ixgbe: fix build error with FCOE_CONFIG without DCB_CONFIG
Building ixgbe without DCB_CONFIG and FCOE_CONFIG will cause
a build error. This resolves the build error by wrapping
the fcoe.up in CONFIG_IXGBE_DCB ifdefs.
Also frames were being priority VLAN tagged even without DCB
enabled. This fixes this so that 8021Q priority tags are
only added with DCB actually enabled.
Reported-by: divya <dipraksh@linux.vnet.ibm.com>
Reported-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Kumar Salecha [Sun, 8 Aug 2010 06:05:23 +0000 (23:05 -0700)]
netxen: protect tx timeout recovery by rtnl lock
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 5 Aug 2010 22:21:26 +0000 (22:21 +0000)]
isdn: gigaset: use after free
I moved the kfree(cb) below the dereferences.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 5 Aug 2010 22:23:23 +0000 (22:23 +0000)]
isdn: gigaset: add missing unlock
We should unlock here. This is the only place where we return from the
function with the lock held. The caller isn't expecting it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Woodhouse [Sun, 8 Aug 2010 06:02:59 +0000 (23:02 -0700)]
solos-pci: Fix race condition in tasklet RX handling
We were seeing faults in the solos-pci receive tasklet when packets
arrived for a VCC which was currently being closed:
[18842.727906] EIP: [<
e082f490>] br2684_push+0x19/0x234 [br2684] SS:ESP 0068:
dfb89d14
[18845.090712] [<
c13ecff3>] ? do_page_fault+0x0/0x2e1
[18845.120042] [<
e082f490>] ? br2684_push+0x19/0x234 [br2684]
[18845.153530] [<
e084fa13>] solos_bh+0x28b/0x7c8 [solos_pci]
[18845.186488] [<
e084f711>] ? solos_irq+0x2d/0x51 [solos_pci]
[18845.219960] [<
c100387b>] ? handle_irq+0x3b/0x48
[18845.247732] [<
c10265cb>] ? irq_exit+0x34/0x57
[18845.274437] [<
c1025720>] tasklet_action+0x42/0x69
[18845.303247] [<
c102643f>] __do_softirq+0x8e/0x129
[18845.331540] [<
c10264ff>] do_softirq+0x25/0x2a
[18845.358274] [<
c102664c>] _local_bh_enable_ip+0x5e/0x6a
[18845.389677] [<
c102666d>] local_bh_enable+0xb/0xe
[18845.417944] [<
e08490a8>] ppp_unregister_channel+0x32/0xbb [ppp_generic]
[18845.458193] [<
e08731ad>] pppox_unbind_sock+0x18/0x1f [pppox]
This patch uses an RCU-inspired approach to fix it. In the RX tasklet's
find_vcc() function we first refuse to use a VCC which already has the
ATM_VF_READY bit cleared. And in the VCC close function, we synchronise
with the tasklet to ensure that it can't still be using the VCC before
we continue and allow the VCC to be destroyed.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Nathan Williams <nathan@traverse.com.au>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Fri, 6 Aug 2010 00:22:35 +0000 (00:22 +0000)]
pkt_sched: Fix sch_sfq vs tcf_bind_filter oops
Since there was added ->tcf_chain() method without ->bind_tcf() to
sch_sfq class options, there is oops when a filter is added with
the classid parameter.
Fixes commit
7d2681a6ff4f9ab5e48d02550b4c6338f1638998
netdev thread: null pointer at cls_api.c
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Reported-by: Franchoze Eric <franchoze@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changli Gao [Sun, 8 Aug 2010 03:35:43 +0000 (20:35 -0700)]
net: disable preemption before call smp_processor_id()
Although netif_rx() isn't expected to be called in process context with
preemption enabled, it'd better handle this case. And this is why get_cpu()
is used in the non-RPS #ifdef branch. If tree RCU is selected,
rcu_read_lock() won't disable preemption, so preempt_disable() should be
called explictly.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Popov [Sun, 8 Aug 2010 03:24:28 +0000 (20:24 -0700)]
tcp: no md5sig option size check bug
tcp_parse_md5sig_option doesn't check md5sig option (TCPOPT_MD5SIG)
length, but tcp_v[46]_inbound_md5_hash assume that it's at least 16
bytes long.
Signed-off-by: Dmitry Popov <dp@highloadlab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 6 Aug 2010 20:30:43 +0000 (13:30 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6
Johannes Berg [Fri, 6 Aug 2010 14:17:53 +0000 (16:17 +0200)]
iwlwifi: fix locking assertions
spin_is_locked() can return zero on some (UP?)
configurations because locks don't exist, and
that causes an endless amount of warnings. Use
lockdep_assert_held() instead, which has two
advantages:
1) it verifies the current task is holding
the lock or mutex
2) it compiles away completely when lockdep
is not enabled
Cc: stable@kernel.org [2.6.34+, maybe only parts of patch]
Reported-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 6 Aug 2010 14:00:48 +0000 (16:00 +0200)]
iwlwifi: fix TX tracer
The TX tracing code copies with the wrong length,
which will typically copy too little data. Fix
this by using the correct length variable.
Cc: stable@kernel.org [2.6.32+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Wed, 4 Aug 2010 23:38:06 +0000 (23:38 +0000)]
isdn: fix information leak
The main motivation of this patch changing strcpy() to strlcpy().
We strcpy() to copy a 48 byte buffers into a 49 byte buffers. So at
best the last byte has leaked information, or maybe there is an
overflow? Anyway, this patch closes the information leaks by zeroing
the memory and the calls to strlcpy() prevent overflows.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Thu, 5 Aug 2010 01:19:11 +0000 (01:19 +0000)]
net: Fix napi_gro_frags vs netpoll path
The netpoll_rx_on() check in __napi_gro_receive() skips part of the
"common" GRO_NORMAL path, especially "pull:" in dev_gro_receive(),
where at least eth header should be copied for entirely paged skbs.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christian Samsel [Wed, 4 Aug 2010 22:14:36 +0000 (22:14 +0000)]
usbnet: remove noisy and hardly useful printk
With turned on hspa modem (Dell 5530 internal card) and activated usb auto
suspend, my system gets up 100 "usbnet_resume has delayed data" per
minute. I didnt noticed any pathological behaviour, so just drop
this message. if any objections, please at least change it to _DEBUG.
Signed-off-by: Christian Samsel <christian.samsel@rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville [Thu, 5 Aug 2010 17:46:27 +0000 (13:46 -0400)]
rtl8180: avoid potential NULL deref in rtl8180_beacon_work
ieee80211_beacon_get can return NULL...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: stable@kernel.org
Sujith [Fri, 30 Jul 2010 06:31:17 +0000 (12:01 +0530)]
ath9k: Remove myself from the MAINTAINERS list
So long.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Williams [Wed, 4 Aug 2010 05:43:47 +0000 (00:43 -0500)]
libertas: scan before assocation if no BSSID was given
Fix this leftover TODO from the cfg80211 conversion by doing a scan
if cfg80211 didn't pass in the BSSID for us. Since the scan code
uses so much of the cfg80211_scan_request structure to build up the
firmware command, we just fake one when the scan request is triggered
internally. But we need to make sure that internal 'fake' cfg82011
scan request does not get back to cfg82011 via cfg80211_scan_done().
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Williams [Fri, 30 Jul 2010 06:16:01 +0000 (23:16 -0700)]
libertas: fix association with some APs by using extended rates
Some APs get pissy if you don't send the firmware the extended rates
in the association request's rates TLV. Found this on a Linksys
WRT54G v2; it denies association with status code 18 unless you
add the extended rates too. The old driver did this, but it got
lost in the cfg80211 conversion.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Williams [Fri, 30 Jul 2010 06:11:30 +0000 (23:11 -0700)]
libertas: get the right # of scanned BSSes
Let's actually check the right field in the command response; and
if there aren't any reported BSSes, exit early with success.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Thu, 5 Aug 2010 19:54:28 +0000 (15:54 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/holtmann/bluetooth-next-2.6
Rusty Russell [Wed, 4 Aug 2010 17:32:05 +0000 (17:32 +0000)]
virtio_net: implements ethtool_ops.get_drvinfo
I often use "ethtool -i" command to check what driver controls the
ehternet device. But because current virtio_net driver doesn't
support "ethtool -i", it becomes the following:
# ethtool -i eth3
Cannot get driver information: Operation not supported
This patch simply adds the "ethtool -i" support. The following is the
result when using the virtio_net driver with my patch applied to.
# ethtool -i eth3
driver: virtio_net
version: N/A
firmware-version: N/A
bus-info: virtio0
Personally, "-i" is one of the most frequently-used option, and most
network drivers support "ethtool -i", so I think virtio_net also
should do.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (use ARRAY_SIZE)
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Wed, 4 Aug 2010 07:34:36 +0000 (07:34 +0000)]
ppp: make channel_ops const
The PPP channel ops structure should be const.
Cleanup the declarations to use standard C99 format.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Wed, 4 Aug 2010 02:34:17 +0000 (02:34 +0000)]
RxRPC: Fix a potential deadlock between the call resend_timer and state_lock
RxRPC can potentially deadlock as rxrpc_resend_time_expired() wants to get
call->state_lock so that it can alter the state of an RxRPC call. However, its
caller (call_timer_fn()) has an apparent lock on the timer struct.
The problem is that rxrpc_resend_time_expired() isn't permitted to lock
call->state_lock as this could cause a deadlock against rxrpc_send_abort() as
that takes state_lock and then attempts to delete the resend timer by calling
del_timer_sync().
The deadlock can occur because del_timer_sync() will sit there forever waiting
for rxrpc_resend_time_expired() to return, but the latter may then wait for
call->state_lock, which rxrpc_send_abort() holds around del_timer_sync()...
This leads to a warning appearing in the kernel log that looks something like
the attached.
It should be sufficient to simply dispense with the locks. It doesn't matter
if we set the resend timer expired event bit and queue the event processor
whilst we're changing state to one where the resend timer is irrelevant as the
event can just be ignored by the processor thereafter.
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.35-rc3-cachefs+ #115
-------------------------------------------------------
swapper/0 is trying to acquire lock:
(&call->state_lock){++--..}, at: [<
ffffffffa00200d4>] rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
but task is already holding lock:
(&call->resend_timer){+.-...}, at: [<
ffffffff8103b675>] run_timer_softirq+0x182/0x2a5
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&call->resend_timer){+.-...}:
[<
ffffffff810560bc>] __lock_acquire+0x889/0x8fa
[<
ffffffff81056184>] lock_acquire+0x57/0x6d
[<
ffffffff8103bb9c>] del_timer_sync+0x3c/0x86
[<
ffffffffa002bb7a>] rxrpc_send_abort+0x50/0x97 [af_rxrpc]
[<
ffffffffa002bdd9>] rxrpc_kernel_abort_call+0xa1/0xdd [af_rxrpc]
[<
ffffffffa0061588>] afs_deliver_to_call+0x129/0x368 [kafs]
[<
ffffffffa006181b>] afs_process_async_call+0x54/0xff [kafs]
[<
ffffffff8104261d>] worker_thread+0x1ef/0x2e2
[<
ffffffff81045f47>] kthread+0x7a/0x82
[<
ffffffff81002cd4>] kernel_thread_helper+0x4/0x10
-> #0 (&call->state_lock){++--..}:
[<
ffffffff81055237>] validate_chain+0x727/0xd23
[<
ffffffff810560bc>] __lock_acquire+0x889/0x8fa
[<
ffffffff81056184>] lock_acquire+0x57/0x6d
[<
ffffffff813e6b69>] _raw_read_lock_bh+0x34/0x43
[<
ffffffffa00200d4>] rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
[<
ffffffff8103b6e6>] run_timer_softirq+0x1f3/0x2a5
[<
ffffffff81036828>] __do_softirq+0xa2/0x13e
[<
ffffffff81002dcc>] call_softirq+0x1c/0x28
[<
ffffffff810049f0>] do_softirq+0x38/0x80
[<
ffffffff810361a2>] irq_exit+0x45/0x47
[<
ffffffff81018fb3>] smp_apic_timer_interrupt+0x88/0x96
[<
ffffffff81002893>] apic_timer_interrupt+0x13/0x20
[<
ffffffff810011ac>] cpu_idle+0x4d/0x83
[<
ffffffff813e06f3>] start_secondary+0x1bd/0x1c1
other info that might help us debug this:
1 lock held by swapper/0:
#0: (&call->resend_timer){+.-...}, at: [<
ffffffff8103b675>] run_timer_softirq+0x182/0x2a5
stack backtrace:
Pid: 0, comm: swapper Not tainted 2.6.35-rc3-cachefs+ #115
Call Trace:
<IRQ> [<
ffffffff81054414>] print_circular_bug+0xae/0xbd
[<
ffffffff81055237>] validate_chain+0x727/0xd23
[<
ffffffff810560bc>] __lock_acquire+0x889/0x8fa
[<
ffffffff810539a7>] ? mark_lock+0x42f/0x51f
[<
ffffffff81056184>] lock_acquire+0x57/0x6d
[<
ffffffffa00200d4>] ? rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
[<
ffffffff813e6b69>] _raw_read_lock_bh+0x34/0x43
[<
ffffffffa00200d4>] ? rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
[<
ffffffffa00200d4>] rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
[<
ffffffff8103b6e6>] run_timer_softirq+0x1f3/0x2a5
[<
ffffffff8103b675>] ? run_timer_softirq+0x182/0x2a5
[<
ffffffffa002007e>] ? rxrpc_resend_time_expired+0x0/0x96 [af_rxrpc]
[<
ffffffff810367ef>] ? __do_softirq+0x69/0x13e
[<
ffffffff81036828>] __do_softirq+0xa2/0x13e
[<
ffffffff81002dcc>] call_softirq+0x1c/0x28
[<
ffffffff810049f0>] do_softirq+0x38/0x80
[<
ffffffff810361a2>] irq_exit+0x45/0x47
[<
ffffffff81018fb3>] smp_apic_timer_interrupt+0x88/0x96
[<
ffffffff81002893>] apic_timer_interrupt+0x13/0x20
<EOI> [<
ffffffff81049de1>] ? __atomic_notifier_call_chain+0x0/0x86
[<
ffffffff8100955b>] ? mwait_idle+0x6e/0x78
[<
ffffffff81009552>] ? mwait_idle+0x65/0x78
[<
ffffffff810011ac>] cpu_idle+0x4d/0x83
[<
ffffffff813e06f3>] start_secondary+0x1bd/0x1c1
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changli Gao [Wed, 4 Aug 2010 04:58:59 +0000 (04:58 +0000)]
sch_sfq: add sanity check for the packet length
The packet length should be checked before the packet data is dereferenced.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changli Gao [Wed, 4 Aug 2010 04:55:40 +0000 (04:55 +0000)]
cls_rsvp: add sanity check for the packet length
The packet length should be checked before the packet data is dereferenced.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changli Gao [Wed, 4 Aug 2010 04:48:12 +0000 (04:48 +0000)]
cls_flow: add sanity check for the packet length
The packet length should be checked before the packet data is dereferenced.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changli Gao [Wed, 4 Aug 2010 04:43:44 +0000 (04:43 +0000)]
sk_buff: introduce pskb_network_may_pull()
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changli Gao [Tue, 3 Aug 2010 17:39:18 +0000 (17:39 +0000)]
act_nat: fix on the TX path
On the TX path, skb->data points to the ethernet header, not the network
header. So when validating the packet length for accessing we should
take the ethernet header into account.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Tue, 3 Aug 2010 09:32:24 +0000 (09:32 +0000)]
drivers/net/enic: Use %pUB to format a UUID
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Weil [Tue, 3 Aug 2010 08:53:45 +0000 (08:53 +0000)]
davinci_emac: Fix use after free in davinci_emac_remove
free_netdev finally calls kfree which makes the contents
of ndev and priv (private data contained in ndev) invalid.
So iounmap should be called before free_netdev.
Cc: David S. Miller <davem@davemloft.net>
Cc: Chaithrika U S <chaithrika@ti.com>
Cc: Sriramakrishnan <srk@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kulikov Vasiliy [Tue, 3 Aug 2010 05:43:18 +0000 (05:43 +0000)]
via-velocity: do not use PCI resources before pci_enable_device()
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kulikov Vasiliy [Tue, 3 Aug 2010 05:43:15 +0000 (05:43 +0000)]
cxgb4vf: do not use PCI resources before pci_enable_device()
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kulikov Vasiliy [Tue, 3 Aug 2010 05:43:11 +0000 (05:43 +0000)]
cxgb3: do not use PCI resources before pci_enable_device()
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 4 Aug 2010 22:31:02 +0000 (15:31 -0700)]
Merge branch 'for-next' of git://git./linux/kernel/git/jikos/trivial
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (48 commits)
Documentation: update broken web addresses.
fix comment typo "choosed" -> "chosen"
hostap:hostap_hw.c Fix typo in comment
Fix spelling contorller -> controller in comments
Kconfig.debug: FAIL_IO_TIMEOUT: typo Faul -> Fault
fs/Kconfig: Fix typo Userpace -> Userspace
Removing dead MACH_U300_BS26
drivers/infiniband: Remove unnecessary casts of private_data
fs/ocfs2: Remove unnecessary casts of private_data
libfc: use ARRAY_SIZE
scsi: bfa: use ARRAY_SIZE
drm: i915: use ARRAY_SIZE
drm: drm_edid: use ARRAY_SIZE
synclink: use ARRAY_SIZE
block: cciss: use ARRAY_SIZE
comment typo fixes: charater => character
fix comment typos concerning "challenge"
arm: plat-spear: fix typo in kerneldoc
reiserfs: typo comment fix
update email address
...
Linus Torvalds [Wed, 4 Aug 2010 22:23:49 +0000 (15:23 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (30 commits)
Revert "HID: add support for the Wacom Intuos 4 wireless"
HID: fix up Kconfig entry for ACRUX driver
HID: add ACRUX game controller force feedback support
HID: Force input registration for "VEC footpedal"
HID: add HID_QUIRK_HIDINPUT_FORCE
HID: hid-input.c: indentation fixes
HID: hiddev: use usb_find_interface, get rid of BKL
HID: ignore digitizer usage Undefined (0x00)
HID: Add support for Conceptronic CLLRCMCE
HID: hid-ids.h: Whitespace fixup, align using TABs
HID: picolcd: implement refcounting of framebuffer
HID: picolcd: do not reallocate memory on depth change
HID: picolcd: Add minimal palette required by fbcon on 8bpp
HID: magicmouse: Correct parsing of large X and Y motions.
HID: magicmouse: report last touch up
HID: picolcd: fix deferred_io init/cleanup to fb ordering
HID: hid-ids.h: keep vendor ids in alphabetical order
HID: add proper support for Elecom BM084 bluetooth mouse
HID: magicmouse: enable horizontal scrolling
HID: magicmouse: add param for scroll speed
...
Linus Torvalds [Wed, 4 Aug 2010 22:23:14 +0000 (15:23 -0700)]
Merge git://git./linux/kernel/git/herbert/crypto-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (39 commits)
random: Reorder struct entropy_store to remove padding on 64bits
padata: update API documentation
padata: Remove padata_get_cpumask
crypto: pcrypt - Update pcrypt cpumask according to the padata cpumask notifier
crypto: pcrypt - Rename pcrypt_instance
padata: Pass the padata cpumasks to the cpumask_change_notifier chain
padata: Rearrange set_cpumask functions
padata: Rename padata_alloc functions
crypto: pcrypt - Dont calulate a callback cpu on empty callback cpumask
padata: Check for valid cpumasks
padata: Allocate cpumask dependend recources in any case
padata: Fix cpu index counting
crypto: geode_aes - Convert pci_table entries to PCI_VDEVICE (if PCI_ANY_ID is used)
pcrypt: Added sysfs interface to pcrypt
padata: Added sysfs primitives to padata subsystem
padata: Make two separate cpumasks
padata: update documentation
padata: simplify serialization mechanism
padata: make padata_do_parallel to return zero on success
padata: Handle empty padata cpumasks
...
Linus Torvalds [Wed, 4 Aug 2010 22:17:52 +0000 (15:17 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tj/percpu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: allow limited allocation before slab is online
percpu: make @dyn_size always mean min dyn_size in first chunk init functions
Linus Torvalds [Wed, 4 Aug 2010 22:15:15 +0000 (15:15 -0700)]
Merge git://git./linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (276 commits)
[SCSI] zfcp: Trigger logging in the FCP channel on qdio error conditions
[SCSI] zfcp: Introduce experimental support for DIF/DIX
[SCSI] zfcp: Enable data division support for FCP devices
[SCSI] zfcp: Prevent access on uninitialized memory.
[SCSI] zfcp: Post events through FC transport class
[SCSI] zfcp: Cleanup QDIO attachment and improve processing.
[SCSI] zfcp: Cleanup function parameters for sbal value.
[SCSI] zfcp: Use correct width for timer_interval field
[SCSI] zfcp: Remove SCSI device when removing unit
[SCSI] zfcp: Use memdup_user and kstrdup
[SCSI] zfcp: Fix retry after failed "open port" erp action
[SCSI] zfcp: Fail erp after timeout
[SCSI] zfcp: Use forced_reopen in terminate_rport_io callback
[SCSI] zfcp: Register SCSI devices after successful fc_remote_port_add
[SCSI] zfcp: Do not try "forced close" when port is already closed
[SCSI] zfcp: Do not unblock rport from REOPEN_PORT_FORCED
[SCSI] sd: add support for runtime PM
[SCSI] implement runtime Power Management
[SCSI] convert to the new PM framework
[SCSI] Unify SAM_ and SAM_STAT_ macros
...
Andy Lutomirski [Sun, 25 Jul 2010 17:14:29 +0000 (13:14 -0400)]
iwlagn: Improve aggregation failure error messages
82ca9341763107615a15da6e59b9535d49eb91c3 added scary looking
but harmless error messages. Make them clearer and make the
actual failure message show up with the same severity as the
harmless one.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kulikov Vasiliy [Tue, 3 Aug 2010 15:43:22 +0000 (19:43 +0400)]
rt2x00: do not use PCI resources before pci_enable_device()
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Tue, 3 Aug 2010 05:22:25 +0000 (08:22 +0300)]
mac80211: Fix compilation warning when CONFIG_INET is not set
The warning is:
net/mac80211/main.c:688: warning: label ‘fail_ifa’ defined but not used
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christoph Fritz [Tue, 3 Aug 2010 10:54:20 +0000 (12:54 +0200)]
wireless: ipw2100: check result of kzalloc()
If kzalloc() fails return with -ENOMEM from ipw2100_net_init() which is
called by register_netdev.
CC: Dan Carpenter <error27@gmail.com>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jan Friedrich [Mon, 2 Aug 2010 21:55:50 +0000 (23:55 +0200)]
ath9k: fix erased ieee80211_rx_status.mactime
ath9k_rx_skb_preprocess nulls rxs and the mactime is never set again -
mactime is always 0. This causes problems in IBSS mode.
ieee80211_rx_bss_info uses mactime to decide if an IBSS merge is needed.
Without this patch the merge is triggered by each beacon received.
This can be recognized by the "beacon TSF higher than local TSF - IBSS
merge with BSSID" log message accompanying each beacon.
This problem was not completely fixed in commit
a6d2055b02dde1067075795274672720baadd3ca and is not a stable kernel fix.
It is solely intended for wireless-testing.
Signed-off-by: Jan Friedrich <jft@dev2day.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sun, 1 Aug 2010 20:40:04 +0000 (15:40 -0500)]
p54pci: Add PCI ID for SMC2802W
The SMC2802W appears to work with p54pci.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: David Cozatt <olbrannon@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lorenzo Bianconi [Sun, 1 Aug 2010 13:47:32 +0000 (15:47 +0200)]
ath9k: fix an issue in ath_atx_tid paused flag management
I noticed a possible issue in the paused flag management of the
ath_atx_tid data structure. In particular, in a noisy environment and
under heavy load, I observed that the AGGR session establishment could
fail several times consecutively causing values of the paused flag
greater than one for this TID (ath_tx_pause_tid is called more than
once from ath_tx_aggr_start).
Considering that the session for this TID can not be established also
after the mac80211 stack calls the ieee80211_agg_tx_operational() since
the ath_tx_aggr_resume() lowers the paused flag only by one.
This patch also replaces some BUG_ON calls with WARN_ON, as even if
these unlikely conditions happen, it's not fatal enough to justify a
BUG_ON.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Sun, 1 Aug 2010 06:25:16 +0000 (02:25 -0400)]
ath9k_hw: Fix regulatory CTL index usage for AR9003
AR9003 was not relying on the CTL indexes from the EEPROM for capping the
max output power. The CTL indexes from the EEPROM provide calibrated
limits for output power for each tested and supported frequency. Without
this the device operates at a power level which only conforms to the
transmit spectrum mask as specified by IEEE Annex I.2.3.
The regulatory limit by CRDA is always used but does not provide
calibrated values for optimal performance, specially on band edges.
Using the calibrated data from the EEPROM ensures the device
operates at optimal output power while still ensuring proper
regulatory compliance. The device uses the minimum of these tree
values, the value from CRDA, the calibrated value from CTL indexex,
and the value to conform to the IEEE transmit spectrum mask.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kulikov Vasiliy [Sat, 31 Jul 2010 16:33:59 +0000 (20:33 +0400)]
net: wl12xx: do not use kfree'd memory
wl1271_dump() uses cmd after kfree(cmd). Move kfree() just after
wl1271_dump().
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Sat, 31 Jul 2010 15:34:12 +0000 (08:34 -0700)]
iwlagn: fix typo in ucode_bt_stats_read debugfs
small typo fix in ucode_bt_stats_read debugfs file
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Sat, 31 Jul 2010 15:34:11 +0000 (08:34 -0700)]
iwlwifi: BA scd_flow not match condition detected
It is a uCode bug which cause the tx queue id not match scd_flow
in compressed block ack frame, and it need to be addressed in uCode.
Currently, driver will log the information when it happen.
Since it is possible happen very often and we do not want to fill the syslog,
so don't enable the logging by default.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sat, 31 Jul 2010 15:34:09 +0000 (08:34 -0700)]
iwlwifi: fix compile warning
When iwlwifi is compiled w/o debug, we get
this warning:
iwl-agn.c: In function ‘iwlagn_load_firmware’:
iwl-agn.c:2014: warning: passing argument 3 of ‘iwl_print_hex_dump’ discards qualifiers from pointer target type
iwl-debug.h:73: note: expected ‘void *’ but argument is of type ‘const u8 *’
because the const qualifier is missing in the
inline stub. Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 30 Jul 2010 22:12:01 +0000 (00:12 +0200)]
ath9k_hw: fix a noise floor calibration related race condition
On AR5008-AR9002, other forms of calibration must not be started while
the noise floor calibration is running, as this can create invalid
readings which were sometimes not even recoverable by any further
calibration attempts.
This patch also ensures that the result of noise floor measurements
are processed faster and also allows the result of the initial
calibration on reset to make it into the NF history buffer
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 30 Jul 2010 22:12:00 +0000 (00:12 +0200)]
ath9k_hw: clean up per-channel calibration data
The noise floor history buffer is currently not kept per channel, which
can lead to problems when changing channels from a clean channel to a
noisy one. Also when switching from HT20 to HT40, the noise floor
history buffer is full of measurements, but none of them contain data
for the extension channel, which it needs quite a bit of time to recover
from.
This patch puts all the per-channel calibration data into a single data
structure, and gives the the driver control over whether that is used
per-channel or even not used for some channels.
For ath9k_htc, I decided to keep this per-channel in order to avoid
creating regressions.
For ath9k, the data is kept only for the operating channel, which saves
some space. ath9k_hw takes care of wiping old data when the operating
channel or its channel flags change.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 30 Jul 2010 22:11:59 +0000 (00:11 +0200)]
ath9k: prevent calibration during off-channel activity
Previously the software scan callback was used to indicate to the hardware,
when it was safe to calibrate. This didn't really work properly, because it
depends on a specific order of software scan callbacks vs. channel changes.
Also, software scans are not the only thing that triggers off-channel
activity, so it's better to use the newly added indication from mac80211 for
this and not use the software scan callback for anything calibration related.
This fixes at least some of the invalid noise floor readings that I've seen
in AP mode on AR9160
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 30 Jul 2010 19:02:12 +0000 (21:02 +0200)]
ath9k_hw: fix analog shift register writes on AR9003
Writes to the analog shift registers, which are issues by the initval
programming function, require a 100 usec delay (similar to AR9002,
but in a different register range).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 30 Jul 2010 19:02:11 +0000 (21:02 +0200)]
ath9k: fix a crash in the PA predistortion apply function
When updating the PAPRD table in hardware, PAPRD itself needs to be
disabled first, otherwise the hardware can throw a data bus error,
which upsets at least some platforms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 30 Jul 2010 19:02:10 +0000 (21:02 +0200)]
ath9k_hw: fix periodic noise floor calibration on AR9003
The periodic noise floor calibration is broken on this chip family, because
it keeps triggering a software-filtered noise floor calibration, but never
reads the result before uploading the history buffer value to the hardware.
Fix this with a call to ath9k_hw_getnf(), just like on AR9002.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 30 Jul 2010 19:02:09 +0000 (21:02 +0200)]
ath9k_hw: clean up and fix initial noise floor calibration
On AR9003 the initial noise floor calibration is currently triggered
at the end of the reset without allowing the hardware to update the
baseband settings. This could potentially make scans in noisy
environments a bit more unreliable, so use the same calibration
sequence that is used on AR9002.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 30 Jul 2010 11:30:47 +0000 (13:30 +0200)]
mac80211: fix scan locking wrt. hw scan
Releasing the scan mutex while starting scans
can lead to unexpected things happening, so
we shouldn't do that. Fix that and hold the
mutex across the scan triggering.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 30 Jul 2010 11:30:46 +0000 (13:30 +0200)]
iwlwifi: fix possible recursive locking deadlock
commit
f84b29ec0a1ab767679d3f2428877b65f94bc3ff
Author: Johannes Berg <johannes.berg@intel.com>
Date: Tue May 18 02:29:13 2010 -0700
iwlwifi: queue user-initiated scan when doing internal scan
introduced a potential deadlock because it calls
ieee80211_scan_completed() with the priv->mutex
held, but mac80211 may call back into iwlwifi
which would lead to recursive locking. Move this
out from under the mutex.
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Linus Torvalds [Wed, 4 Aug 2010 18:47:58 +0000 (11:47 -0700)]
Merge git://git./linux/kernel/git/davem/net-next-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1443 commits)
phy/marvell: add 88ec048 support
igb: Program MDICNFG register prior to PHY init
e1000e: correct MAC-PHY interconnect register offset for 82579
hso: Add new product ID
can: Add driver for esd CAN-USB/2 device
l2tp: fix export of header file for userspace
can-raw: Fix skb_orphan_try handling
Revert "net: remove zap_completion_queue"
net: cleanup inclusion
phy/marvell: add 88e1121 interface mode support
u32: negative offset fix
net: Fix a typo from "dev" to "ndev"
igb: Use irq_synchronize per vector when using MSI-X
ixgbevf: fix null pointer dereference due to filter being set for VLAN 0
e1000e: Fix irq_synchronize in MSI-X case
e1000e: register pm_qos request on hardware activation
ip_fragment: fix subtracting PPPOE_SES_HLEN from mtu twice
net: Add getsockopt support for TCP thin-streams
cxgb4: update driver version
cxgb4: add new PCI IDs
...
Manually fix up conflicts in:
- drivers/net/e1000e/netdev.c: due to pm_qos registration
infrastructure changes
- drivers/net/phy/marvell.c: conflict between adding 88ec048 support
and cleaning up the IDs
- drivers/net/wireless/ipw2x00/ipw2100.c: trivial ipw2100_pm_qos_req
conflict (registration change vs marking it static)
Linus Torvalds [Wed, 4 Aug 2010 18:25:58 +0000 (11:25 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/konrad/ibft-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibft-2.6:
ibft: Use IBFT_SIGN instead of open-coding the search string.
ibft: convert iscsi_ibft module to iscsi boot lib
ibft: separate ibft parsing from sysfs interface
ibft: For UEFI machines actually do scan ACPI for iBFT.
ibft: Update iBFT handling for v1.03 of the spec.
Linus Torvalds [Wed, 4 Aug 2010 18:23:59 +0000 (11:23 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/bp/bp
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
amd64_edac: Minor formatting fix
amd64_edac: Fix operator precendence error
edac, mc: Improve scrub rate handling
amd64_edac: Correct scrub rate setting
amd64_edac: Fix DCT base address selector
amd64_edac: Remove polling mechanism
x86, mce: Notify about corrected events too
amd64_edac: Remove unneeded defines
edac: Remove EDAC_DEBUG_VERBOSE
amd64_edac: Sanitize syndrome extraction
David Howells [Wed, 4 Aug 2010 15:59:14 +0000 (16:59 +0100)]
CRED: Fix RCU warning due to previous patch fixing __task_cred()'s checks
Commit
8f92054e7ca1 ("CRED: Fix __task_cred()'s lockdep check and banner
comment") fixed the lockdep checks on __task_cred(). This has shown up
a place in the signalling code where a lock should be held - namely that
check_kill_permission() requires its callers to hold the RCU lock.
Fix group_send_sig_info() to get the RCU read lock around its call to
check_kill_permission().
Without this patch, the following warning can occur:
===================================================
[ INFO: suspicious rcu_dereference_check() usage. ]
---------------------------------------------------
kernel/signal.c:660 invoked rcu_dereference_check() without protection!
...
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tejun Heo [Wed, 4 Aug 2010 15:59:39 +0000 (17:59 +0200)]
block_dev: always serialize exclusive open attempts
bd_prepare_to_claim() incorrectly allowed multiple attempts for
exclusive open to progress in parallel if the attempting holders are
identical. This triggered BUG_ON() as reported in the following bug.
https://bugzilla.kernel.org/show_bug.cgi?id=16393
__bd_abort_claiming() is used to finish claiming blocks and doesn't
work if multiple openers are inside a claiming block. Allowing
multiple parallel open attempts to continue doesn't gain anything as
those are serialized down in the call chain anyway. Fix it by always
allowing only single open attempt in a claiming block.
This problem can easily be reproduced by adding a delay after
bd_prepare_to_claim() and attempting to mount two partitions of a
disk.
stable: only applicable to v2.6.35
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kyle McMartin [Wed, 4 Aug 2010 00:38:08 +0000 (20:38 -0400)]
parisc: pass through '\t' to early (iodc) console
The firmware handles '\t' internally, so stop trying to emulate it
(which, incidentally, had a bug in it.)
Fixes a really weird hang at bootup in rcu_bootup_announce, which,
as far as I can tell, is the first printk in the core kernel to use
a tab as the first character.
Cc: stable@kernel.org
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 4 Aug 2010 18:14:36 +0000 (11:14 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/rafael/suspend-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM / Runtime: Add runtime PM statistics (v3)
PM / Runtime: Make runtime_status attribute not debug-only (v. 2)
PM: Do not use dynamically allocated objects in pm_wakeup_event()
PM / Suspend: Fix ordering of calls in suspend error paths
PM / Hibernate: Fix snapshot error code path
PM / Hibernate: Fix hibernation_platform_enter()
pm_qos: Get rid of the allocation in pm_qos_add_request()
pm_qos: Reimplement using plists
plist: Add plist_last
PM: Make it possible to avoid races between wakeup and system sleep
PNPACPI: Add support for remote wakeup
PM: describe kernel policy regarding wakeup defaults (v. 2)
PM / Hibernate: Fix typos in comments in kernel/power/swap.c
Linus Torvalds [Wed, 4 Aug 2010 18:13:36 +0000 (11:13 -0700)]
Merge branch 'next' of git://git./linux/kernel/git/davej/cpufreq
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Remove pointless printk from p4-clockmod.
[CPUFREQ] Fix section mismatch for powernow_cpu_init in powernow-k7.c
[CPUFREQ] Fix section mismatch for longhaul_cpu_init.
[CPUFREQ] Fix section mismatch for longrun_cpu_init.
[CPUFREQ] powernow-k8: Fix misleading variable naming
[CPUFREQ] Convert pci_table entries to PCI_VDEVICE (if PCI_ANY_ID is used)
[CPUFREQ] arch/x86/kernel/cpu/cpufreq: use for_each_pci_dev()
[CPUFREQ] fix brace coding style issue.
[CPUFREQ] x86 cpufreq: Make trace_power_frequency cpufreq driver independent
[CPUFREQ] acpi-cpufreq: Fix CPU_ANY CPUFREQ_{PRE,POST}CHANGE notification
[CPUFREQ] ondemand: don't synchronize sample rate unless multiple cpus present
[CPUFREQ] unexport (un)lock_policy_rwsem* functions
[CPUFREQ] ondemand: Refactor frequency increase code
[CPUFREQ] powernow-k8: On load failure, remind the user to enable support in BIOS setup
[CPUFREQ] powernow-k8: Limit Pstate transition latency check
[CPUFREQ] Fix PCC driver error path
[CPUFREQ] fix double freeing in error path of pcc-cpufreq
[CPUFREQ] pcc driver should check for pcch method before calling _OSC
[CPUFREQ] fix memory leak in cpufreq_add_dev
[CPUFREQ] revert "[CPUFREQ] remove rwsem lock from CPUFREQ_GOV_STOP call (second call site)"
Manually fix up non-data merge conflict introduced by new calling
conventions for trace_power_start() in commit
6f4f2723d085 ("x86
cpufreq: Make trace_power_frequency cpufreq driver independent"), which
didn't update the intel_idle native hardware cpuidle driver.
Linus Torvalds [Wed, 4 Aug 2010 17:44:06 +0000 (10:44 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/mjg59/platform-drivers-x86
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (88 commits)
ips driver: make it less chatty
intel_scu_ipc: fix size field for intel_scu_ipc_command
intel_scu_ipc: return -EIO for error condition in busy_loop
intel_scu_ipc: fix data packing of PMIC command on Moorestown
Clean up command packing on MRST.
zero the stack buffer before giving random garbage to the SCU
Fix stack buffer size for IPC writev messages
intel_scu_ipc: Use the new cpu identification function
intel_scu_ipc: tidy up unused bits
Remove indirect read write api support.
intel_scu_ipc: Support Medfield processors
intel_scu_ipc: detect CPU type automatically
x86 plat: limit x86 platform driver menu to X86
acpi ec_sys: Be more cautious about ec write access
acpi ec: Fix possible double io port registration
hp-wmi: acpi_drivers.h is already included through acpi.h two lines below
hp-wmi: Fix mixing up of and/or directive
dell-laptop: make dell_laptop_i8042_filter() static
asus-laptop: fix asus_input_init error path
msi-wmi: make needlessly global symbols static
...
Linus Torvalds [Wed, 4 Aug 2010 17:43:01 +0000 (10:43 -0700)]
Merge branch 'kvm-updates/2.6.36' of git://git./virt/kvm/kvm
* 'kvm-updates/2.6.36' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (198 commits)
KVM: VMX: Fix host GDT.LIMIT corruption
KVM: MMU: using __xchg_spte more smarter
KVM: MMU: cleanup spte set and accssed/dirty tracking
KVM: MMU: don't atomicly set spte if it's not present
KVM: MMU: fix page dirty tracking lost while sync page
KVM: MMU: fix broken page accessed tracking with ept enabled
KVM: MMU: add missing reserved bits check in speculative path
KVM: MMU: fix mmu notifier invalidate handler for huge spte
KVM: x86 emulator: fix xchg instruction emulation
KVM: x86: Call mask notifiers from pic
KVM: x86: never re-execute instruction with enabled tdp
KVM: Document KVM_GET_SUPPORTED_CPUID2 ioctl
KVM: x86: emulator: inc/dec can have lock prefix
KVM: MMU: Eliminate redundant temporaries in FNAME(fetch)
KVM: MMU: Validate all gptes during fetch, not just those used for new pages
KVM: MMU: Simplify spte fetch() function
KVM: MMU: Add gpte_valid() helper
KVM: MMU: Add validate_direct_spte() helper
KVM: MMU: Add drop_large_spte() helper
KVM: MMU: Use __set_spte to link shadow pages
...
Linus Torvalds [Wed, 4 Aug 2010 17:41:52 +0000 (10:41 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
Input: adp5588-keypad - fix NULL dereference in adp5588_gpio_add()
Input: cy8ctmg110 - capacitive touchscreen support
Input: keyboard - also match braille-only keyboards
Input: adp5588-keys - export unused GPIO pins
Input: xpad - add product ID for Hori Fighting Stick EX2
Input: adxl34x - fix leak and use after free
Input: samsung-keypad - Add samsung keypad driver
Input: i8042 - reset keyboard controller wehen resuming from S2R
Input: synaptics - set min/max for finger width
Input: synaptics - only report width on hardware that supports it
Input: evdev - signal that device is writable in evdev_poll()
Input: mousedev - signal that device is writable in mousedev_poll()
Input: change input handlers to use bool when possible
Input: document the MT event slot protocol
Input: introduce MT event slots
Input: usbtouchscreen - implement reset_resume
Input: usbtouchscreen - implement runtime power management
Input: usbtouchscreen - implement basic suspend/resume
Input: Add ATMEL QT602240 touchscreen driver
Input: fix signedness warning in input_set_keycode()
...
Linus Torvalds [Wed, 4 Aug 2010 17:38:08 +0000 (10:38 -0700)]
Merge branch 'v4l_for_2.6.35' of git://git./linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (243 commits)
V4L/DVB: sms: Convert IR support to use the Remote Controller core
V4L/DVB: sms: properly initialize IR phys and IR name
V4L/DVB: standardize names at rc-dib0700 tables
V4L/DVB: smsusb: enable IR port for Hauppauge WinTV MiniStick
V4L/DVB: dib0700: Fix RC protocol logic to properly handle NEC/NECx and RC-5
V4L/DVB: dib0700: properly implement IR change_protocol
V4L/DVB: dib0700: break keytable into NEC and RC-5 variants
V4L/DVB: dib0700: avoid bad repeat
V4L/DVB: Port dib0700 to rc-core
V4L/DVB: Add a keymap file with dib0700 table
V4L/DVB: dvb-usb: add support for rc-core mode
V4L/DVB: dvb-usb: prepare drivers for using rc-core
V4L/DVB: dvb-usb: get rid of struct dvb_usb_rc_key
V4L/DVB: rj54n1cb0c: fix a comment in the driver
V4L/DVB: V4L2: sh_vou: VOU does support the full PAL resolution too
V4L/DVB: V4L2: sh_mobile_camera_ceu: add support for CSI2
V4L/DVB: V4L2: soc-camera: add a MIPI CSI-2 driver for SH-Mobile platforms
V4L/DVB: V4L2: soc-camera: export soc-camera bus type for notifications
V4L/DVB: V4L2: mediabus: add 12-bit Bayer and YUV420 pixel formats
V4L/DVB: mediabus: fix ambiguous pixel code names
...
Linus Torvalds [Wed, 4 Aug 2010 17:36:39 +0000 (10:36 -0700)]
Merge branch 'stable/swiotlb-0.8.3' of git://git./linux/kernel/git/konrad/swiotlb-2.6
* 'stable/swiotlb-0.8.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb-2.6:
swiotlb: Make swiotlb bookkeeping functions visible in the header file.
swiotlb: search and replace "int dir" with "enum dma_data_direction dir"
swiotlb: Make internal bookkeeping functions have 'swiotlb_tbl' prefix.
swiotlb: add the swiotlb initialization function with iotlb memory
swiotlb: add swiotlb_tbl_map_single library function
Linus Torvalds [Wed, 4 Aug 2010 17:28:39 +0000 (10:28 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (90 commits)
AppArmor: fix build warnings for non-const use of get_task_cred
selinux: convert the policy type_attr_map to flex_array
AppArmor: Enable configuring and building of the AppArmor security module
TOMOYO: Use pathname specified by policy rather than execve()
AppArmor: update path_truncate method to latest version
AppArmor: core policy routines
AppArmor: policy routines for loading and unpacking policy
AppArmor: mediation of non file objects
AppArmor: LSM interface, and security module initialization
AppArmor: Enable configuring and building of the AppArmor security module
AppArmor: update Maintainer and Documentation
AppArmor: functions for domain transitions
AppArmor: file enforcement routines
AppArmor: userspace interfaces
AppArmor: dfa match engine
AppArmor: contexts used in attaching policy to system objects
AppArmor: basic auditing infrastructure.
AppArmor: misc. base functions and defines
TOMOYO: Update version to 2.3.0
TOMOYO: Fix quota check.
...
Ville Tervo [Wed, 4 Aug 2010 06:43:33 +0000 (09:43 +0300)]
Bluetooth: Check result code of L2CAP information response
Check result code of L2CAP information response. Otherwise
it would read invalid feature mask and access invalid memory.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Gustavo F. Padovan [Wed, 4 Aug 2010 02:49:29 +0000 (23:49 -0300)]
Bluetooth: Don't send RFC for Basic Mode if only it is supported
If the remote side doesn't support Enhanced Retransmission Mode neither
Streaming Mode, we shall not send the RFC option.
Some devices that only supports Basic Mode do not understanding the RFC
option. This patch fixes the regression found with these devices.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jiri Kosina [Wed, 4 Aug 2010 13:31:24 +0000 (15:31 +0200)]
Merge branch 'bkl' into for-linus
Jiri Kosina [Wed, 4 Aug 2010 13:31:13 +0000 (15:31 +0200)]
Merge branches 'magicmouse', 'roccat' and 'vec-pedal' into for-linus
Conflicts:
drivers/hid/hid-ids.h
Jiri Kosina [Wed, 4 Aug 2010 13:29:35 +0000 (15:29 +0200)]
Merge branch 'acrux' into for-linus
Conflicts:
drivers/hid/hid-ids.h
Jiri Kosina [Wed, 4 Aug 2010 13:27:54 +0000 (15:27 +0200)]
Merge branch 'upstream-fixes' into for-linus
Conflicts:
drivers/hid/hid-ids.h
Jiri Kosina [Wed, 4 Aug 2010 13:26:15 +0000 (15:26 +0200)]
Merge branch 'upstream' into for-linus
Conflicts:
drivers/hid/hid-ids.h
Justin P. Mattock [Sat, 24 Jul 2010 03:51:24 +0000 (20:51 -0700)]
Documentation: update broken web addresses.
Below you will find an updated version from the original series bunching all patches into one big patch
updating broken web addresses that are located in Documentation/*
Some of the addresses date as far far back as 1995 etc... so searching became a bit difficult,
the best way to deal with these is to use web.archive.org to locate these addresses that are outdated.
Now there are also some addresses pointing to .spec files some are located, but some(after searching
on the companies site)where still no where to be found. In this case I just changed the address
to the company site this way the users can contact the company and they can locate them for the users.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Cc: Paulo Marques <pmarques@grupopie.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Michael Neuling <mikey@neuling.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jiri Kosina [Wed, 4 Aug 2010 13:14:38 +0000 (15:14 +0200)]
Merge branch 'master' into for-next
Uwe Kleine-König [Fri, 30 Jul 2010 19:02:47 +0000 (21:02 +0200)]
fix comment typo "choosed" -> "chosen"
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Justin P. Mattock [Mon, 2 Aug 2010 20:50:43 +0000 (13:50 -0700)]
hostap:hostap_hw.c Fix typo in comment
The patch below fixes a typo in a comment.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Stefan Weil [Tue, 3 Aug 2010 17:44:52 +0000 (19:44 +0200)]
Fix spelling contorller -> controller in comments
Cc: Jiri Kosina <trivial@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Borislav Petkov [Tue, 3 Aug 2010 15:25:18 +0000 (17:25 +0200)]
amd64_edac: Minor formatting fix
EDAC MC3: CE page 0xc32281, offset 0x8a0, grain 0, syndrome 0x1, row 2, channel 1, label "": amd64_edac
EDAC MC3: CE - no information available: amd64_edacError Overflow
Add the missing space before "Error Overflow" on the second line.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Tue, 3 Aug 2010 14:51:28 +0000 (16:51 +0200)]
amd64_edac: Fix operator precendence error
The bitwise AND is of higher precedence, make that explicit.
Cc: <stable@kernel.org> # 34.x
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cyril Chemparathy [Wed, 4 Aug 2010 02:36:06 +0000 (19:36 -0700)]
phy/marvell: add 88ec048 support
Marvell 88ec048 is a derivative of its 88e1121r device. From the programmer's
perspective, the one major difference is the addition of an additional control
bit in Page 2 Register 16 - used to control the padding of odd nibble
preambles.
This patch adds support for this new device, while inheriting as much code as
possible from the existing 88e1121r implementation.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Tue, 3 Aug 2010 11:50:08 +0000 (11:50 +0000)]
igb: Program MDICNFG register prior to PHY init
This patch addresses an issue seen on 82580 in which the MDICNFG
register will be reset during a single function reset and as a
result we will be unable to communicate with the PHY. To correct
the issue, added a call to reset_mdicnfg just prior to the first
access of the MDICNFG register in sgnii_uses_mdio.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Tue, 3 Aug 2010 11:48:35 +0000 (11:48 +0000)]
e1000e: correct MAC-PHY interconnect register offset for 82579
The MAC-PHY interconnect register set on ICH/PCH parts is accessed through
a peephole mechanism by writing an offset to a CSR register. The offset
for the interconnect's half-duplex control register (which is used in a
jumbo frame workaround for 82579) is incorrect.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filip Aben [Tue, 3 Aug 2010 05:36:41 +0000 (05:36 +0000)]
hso: Add new product ID
This patch adds a new product ID to the hso driver.
Signed-off-by: Filip Aben <f.aben@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matthias Fuchs [Tue, 3 Aug 2010 02:55:23 +0000 (02:55 +0000)]
can: Add driver for esd CAN-USB/2 device
This patch adds a driver for esd's USB high speed
CAN interface. The driver supports devices with
multiple CAN interfaces.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 3 Aug 2010 21:40:10 +0000 (14:40 -0700)]
Merge git://git./linux/kernel/git/steve/gfs2-2.6-nmw
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-nmw:
GFS2: Fix recovery stuck bug (try #2)
GFS2: Fix typo in stuffed file data copy handling
Revert "GFS2: recovery stuck on transaction lock"
GFS2: Make "try" lock not try quite so hard
GFS2: remove dependency on __GFP_NOFAIL
GFS2: Simplify gfs2_write_alloc_required
GFS2: Wait for journal id on mount if not specified on mount command line
GFS2: Use nobh_writepage
Linus Torvalds [Tue, 3 Aug 2010 21:37:26 +0000 (14:37 -0700)]
Merge branch 'linux-next' of git://git.infradead.org/ubi-2.6
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: do not warn unnecessarily
UBI: do not print message about corruptes PEBs if we have none of them
UBI: improve delete-compatible volumes handling
UBI: fix error message and compilation warnings
UBI: generate random image_seq when formatting MTD devices
UBI: improve ECC error message
UBI: improve corrupted flash handling
UBI: introduce eraseblock counter variables
UBI: introduce a new IO return code
UBI: simplify IO error codes
Linus Torvalds [Tue, 3 Aug 2010 21:37:02 +0000 (14:37 -0700)]
Merge branch 'linux-next' of git://git.infradead.org/ubifs-2.6
* 'linux-next' of git://git.infradead.org/ubifs-2.6:
UBIFS: fix a memory leak on error path.
UBIFS: fix GC LEB recovery
UBIFS: use ERR_CAST
UBIFS: check return code
Linus Torvalds [Tue, 3 Aug 2010 21:36:16 +0000 (14:36 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ericvh/v9fs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs: (22 commits)
9p: fix sparse warnings in new xattr code
fs/9p: remove sparse warning in vfs_inode
fs/9p: destroy fid on failed remove
fs/9p: Prevent parallel rename when doing fid_lookup
fs/9p: Add support user. xattr
net/9p: Implement TXATTRCREATE 9p call
net/9p: Implement attrwalk 9p call
9p: Implement LOPEN
fs/9p: This patch implements TLCREATE for 9p2000.L protocol.
9p: Implement TMKDIR
9p: Implement TMKNOD
9p: Define and implement TSYMLINK for 9P2000.L
9p: Define and implement TLINK for 9P2000.L
9p: Define and implement TLINK for 9P2000.L
9p: Implement client side of setattr for 9P2000.L protocol.
9p: getattr client implementation for 9P2000.L protocol.
fs/9p: Pass the correct user credentials during attach
net/9p: Handle the server returned error properly
9p: readdir implementation for 9p2000.L
9p: Make use of iounit for read/write
...