review.tizen.org Git - platform/kernel/linux-rpi.git/log

net: enetc: workaround for unresponsive pMAC after receiving express traffic

I have observed an issue where the RX direction of the LS1028A ENETC pMAC
seems unresponsive. The minimal procedure to reproduce the issue is:

1. Connect ENETC port 0 with a loopback RJ45 cable to one of the Felix
   switch ports (0).

2. Bring the ports up (MAC Merge layer is not enabled on either end).

3. Send a large quantity of unidirectional (express) traffic from Felix
   to ENETC. I tried altering frame size and frame count, and it doesn't
   appear to be specific to either of them, but rather, to the quantity
   of octets received. Lowering the frame count, the minimum quantity of
   packets to reproduce relatively consistently seems to be around 37000
   frames at 1514 octets (w/o FCS) each.

4. Using ethtool --set-mm, enable the pMAC in the Felix and in the ENETC
   ports, in both RX and TX directions, and with verification on both
   ends.

5. Wait for verification to complete on both sides.

6. Configure a traffic class as preemptible on both ends.

7. Send some packets again.

The issue is at step 5, where the verification process of ENETC ends
(meaning that Felix responds with an SMD-R and ENETC sees the response),
but the verification process of Felix never ends (it remains VERIFYING).

If step 3 is skipped or if ENETC receives less traffic than
approximately that threshold, the test runs all the way through
(verification succeeds on both ends, preemptible traffic passes fine).

If, between step 4 and 5, the step below is also introduced:

4.1. Disable and re-enable PM0_COMMAND_CONFIG bit RX_EN

then again, the sequence of steps runs all the way through, and
verification succeeds, even if there was the previous RX traffic
injected into ENETC.

Traffic sent *by* the ENETC port prior to enabling the MAC Merge layer
does not seem to influence the verification result, only received
traffic does.

The LS1028A manual does not mention any relationship between
PM0_COMMAND_CONFIG and MMCSR, and the hardware people don't seem to
know for now either.

The bit that is toggled to work around the issue is also toggled
by enetc_mac_enable(), called from phylink's mac_link_down() and
mac_link_up() methods - which is how the workaround was found:
verification would work after a link down/up.

Fixes: c7b9e8086902 ("net: enetc: add support for MAC Merge layer")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230411192645.1896048-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

sctp: fix a potential overflow in sctp_ifwdtsn_skip

Currently, when traversing ifwdtsn skips with _sctp_walk_ifwdtsn, it only
checks the pos against the end of the chunk. However, the data left for
the last pos may be < sizeof(struct sctp_ifwdtsn_skip), and dereference
it as struct sctp_ifwdtsn_skip may cause coverflow.

This patch fixes it by checking the pos against "the end of the chunk -
sizeof(struct sctp_ifwdtsn_skip)" in sctp_ifwdtsn_skip, similar to
sctp_fwdtsn_skip.

Fixes: 0fc2ea922c8a ("sctp: implement validate_ftsn for sctp_stream_interleave")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/2a71bffcd80b4f2c61fac6d344bb2f11c8fd74f7.1681155810.git.lucien.xin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: qrtr: Fix an uninit variable access bug in qrtr_tx_resume()

Syzbot reported a bug as following:

=====================================================
BUG: KMSAN: uninit-value in qrtr_tx_resume+0x185/0x1f0 net/qrtr/af_qrtr.c:230
qrtr_tx_resume+0x185/0x1f0 net/qrtr/af_qrtr.c:230
qrtr_endpoint_post+0xf85/0x11b0 net/qrtr/af_qrtr.c:519
qrtr_tun_write_iter+0x270/0x400 net/qrtr/tun.c:108
call_write_iter include/linux/fs.h:2189 [inline]
aio_write+0x63a/0x950 fs/aio.c:1600
io_submit_one+0x1d1c/0x3bf0 fs/aio.c:2019
__do_sys_io_submit fs/aio.c:2078 [inline]
__se_sys_io_submit+0x293/0x770 fs/aio.c:2048
__x64_sys_io_submit+0x92/0xd0 fs/aio.c:2048
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

Uninit was created at:
slab_post_alloc_hook mm/slab.h:766 [inline]
slab_alloc_node mm/slub.c:3452 [inline]
__kmem_cache_alloc_node+0x71f/0xce0 mm/slub.c:3491
__do_kmalloc_node mm/slab_common.c:967 [inline]
__kmalloc_node_track_caller+0x114/0x3b0 mm/slab_common.c:988
kmalloc_reserve net/core/skbuff.c:492 [inline]
__alloc_skb+0x3af/0x8f0 net/core/skbuff.c:565
__netdev_alloc_skb+0x120/0x7d0 net/core/skbuff.c:630
qrtr_endpoint_post+0xbd/0x11b0 net/qrtr/af_qrtr.c:446
qrtr_tun_write_iter+0x270/0x400 net/qrtr/tun.c:108
call_write_iter include/linux/fs.h:2189 [inline]
aio_write+0x63a/0x950 fs/aio.c:1600
io_submit_one+0x1d1c/0x3bf0 fs/aio.c:2019
__do_sys_io_submit fs/aio.c:2078 [inline]
__se_sys_io_submit+0x293/0x770 fs/aio.c:2048
__x64_sys_io_submit+0x92/0xd0 fs/aio.c:2048
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

It is because that skb->len requires at least sizeof(struct qrtr_ctrl_pkt)
in qrtr_tx_resume(). And skb->len equals to size in qrtr_endpoint_post().
But size is less than sizeof(struct qrtr_ctrl_pkt) when qrtr_cb->type
equals to QRTR_TYPE_RESUME_TX in qrtr_endpoint_post() under the syzbot
scenario. This triggers the uninit variable access bug.

Add size check when qrtr_cb->type equals to QRTR_TYPE_RESUME_TX in
qrtr_endpoint_post() to fix the bug.

Fixes: 5fdeb0d372ab ("net: qrtr: Implement outgoing flow control")
Reported-by: syzbot+4436c9630a45820fda76@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=c14607f0963d27d5a3d5f4c8639b500909e43540
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230410012352.3997823-1-william.xuanziyang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

rtnetlink: Restore RTM_NEW/DELLINK notification behavior

The commits referenced below allows userspace to use the NLM_F_ECHO flag
for RTM_NEW/DELLINK operations to receive unicast notifications for the
affected link. Prior to these changes, applications may have relied on
multicast notifications to learn the same information without specifying
the NLM_F_ECHO flag.

For such applications, the mentioned commits changed the behavior for
requests not using NLM_F_ECHO. Multicast notifications are still received,
but now use the portid of the requester and the sequence number of the
request instead of zero values used previously. For the application, this
message may be unexpected and likely handled as a response to the
NLM_F_ACKed request, especially if it uses the same socket to handle
requests and notifications.

To fix existing applications relying on the old notification behavior,
set the portid and sequence number in the notification only if the
request included the NLM_F_ECHO flag. This restores the old behavior
for applications not using it, but allows unicasted notifications for
others.

Fixes: f3a63cce1b4f ("rtnetlink: Honour NLM_F_ECHO flag in rtnl_delete_link")
Fixes: d88e136cab37 ("rtnetlink: Honour NLM_F_ECHO flag in rtnl_newlink_create")
Signed-off-by: Martin Willi <martin@strongswan.org>
Acked-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20230411074319.24133-1-martin@strongswan.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: ti/cpsw: Add explicit platform_device.h and of_platform.h includes

TI CPSW uses of_platform_* functions which are declared in of_platform.h.
of_platform.h gets implicitly included by of_device.h, but that is going
to be removed soon. Nothing else depends on of_device.h so it can be
dropped. of_platform.h also implicitly includes platform_device.h, so
add an explicit include for it, too.

Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: wwan: iosm: Fix error handling path in ipc_pcie_probe()

Smatch reports:
drivers/net/wwan/iosm/iosm_ipc_pcie.c:298 ipc_pcie_probe()
warn: missing unwind goto?

When dma_set_mask fails it directly returns without disabling pci
device and freeing ipc_pcie. Fix this my calling a correct goto label

As dma_set_mask returns either 0 or -EIO, we can use a goto label, as
it finally returns -EIO.

Add a set_mask_fail goto label which stands consistent with other goto
labels in this function..

Fixes: 035e3befc191 ("net: wwan: iosm: fix driver not working with INTEL_IOMMU disabled")
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

smc: Fix use-after-free in tcp_write_timer_handler().

With Eric's ref tracker, syzbot finally found a repro for
use-after-free in tcp_write_timer_handler() by kernel TCP
sockets. [0]

If SMC creates a kernel socket in __smc_create(), the kernel
socket is supposed to be freed in smc_clcsock_release() by
calling sock_release() when we close() the parent SMC socket.

However, at the end of smc_clcsock_release(), the kernel
socket's sk_state might not be TCP_CLOSE. This means that
we have not called inet_csk_destroy_sock() in __tcp_close()
and have not stopped the TCP timers.

The kernel socket's TCP timers can be fired later, so we
need to hold a refcnt for net as we do for MPTCP subflows
in mptcp_subflow_create_socket().

[0]:
leaked reference.
sk_alloc (./include/net/net_namespace.h:335 net/core/sock.c:2108)
inet_create (net/ipv4/af_inet.c:319 net/ipv4/af_inet.c:244)
__sock_create (net/socket.c:1546)
smc_create (net/smc/af_smc.c:3269 net/smc/af_smc.c:3284)
__sock_create (net/socket.c:1546)
__sys_socket (net/socket.c:1634 net/socket.c:1618 net/socket.c:1661)
__x64_sys_socket (net/socket.c:1672)
do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120)
==================================================================
BUG: KASAN: slab-use-after-free in tcp_write_timer_handler (net/ipv4/tcp_timer.c:378 net/ipv4/tcp_timer.c:624 net/ipv4/tcp_timer.c:594)
Read of size 1 at addr ffff888052b65e0d by task syzrepro/18091

CPU: 0 PID: 18091 Comm: syzrepro Tainted: G W 6.3.0-rc4-01174-gb5d54eb5899a #7
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-1.amzn2022.0.1 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl (lib/dump_stack.c:107)
print_report (mm/kasan/report.c:320 mm/kasan/report.c:430)
kasan_report (mm/kasan/report.c:538)
tcp_write_timer_handler (net/ipv4/tcp_timer.c:378 net/ipv4/tcp_timer.c:624 net/ipv4/tcp_timer.c:594)
tcp_write_timer (./include/linux/spinlock.h:390 net/ipv4/tcp_timer.c:643)
call_timer_fn (./arch/x86/include/asm/jump_label.h:27 ./include/linux/jump_label.h:207 ./include/trace/events/timer.h:127 kernel/time/timer.c:1701)
__run_timers.part.0 (kernel/time/timer.c:1752 kernel/time/timer.c:2022)
run_timer_softirq (kernel/time/timer.c:2037)
__do_softirq (./arch/x86/include/asm/jump_label.h:27 ./include/linux/jump_label.h:207 ./include/trace/events/irq.h:142 kernel/softirq.c:572)
__irq_exit_rcu (kernel/softirq.c:445 kernel/softirq.c:650)
irq_exit_rcu (kernel/softirq.c:664)
sysvec_apic_timer_interrupt (arch/x86/kernel/apic/apic.c:1107 (discriminator 14))
</IRQ>

Fixes: ac7138746e14 ("smc: establish new socket family")
Reported-by: syzbot+7e1e1bdb852961150198@syzkaller.appspotmail.com
Link: https://lore.kernel.org/netdev/000000000000a3f51805f8bcc43a@google.com/
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: check pci_reset_function result

Static code analyzer complains to unchecked return value.
The result of pci_reset_function() is unchecked.
Despite, the issue is on the FLR supported code path and in that
case reset can be done with pcie_flr(), the patch uses less invasive
approach by adding the result check of pci_reset_function().

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: 7e2cf4feba05 ("qlcnic: change driver hardware interface mechanism")
Signed-off-by: Denis Plotnikov <den-plotnikov@yandex-team.ru>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch '40GbE' of git://git./linux/kernel/git/tnguy/net-queue

Tony Nguyen says:

====================
iavf: fix racing in VLANs

Ahmed Zaki says:

This patchset mainly fixes a racing issue in the iavf where the number of
VLANs in the vlan_filter_list might be more than the PF limit. To fix that,
we get rid of the cvlans and svlans bitmaps and keep all the required info
in the list.

The second patch adds two new states that are needed so that we keep the
VLAN info while the interface goes DOWN:
    -- DISABLE    (notify PF, but keep the filter in the list)
    -- INACTIVE   (dev is DOWN, filter is removed from PF)

Finally, the current code keeps each state in a separate bit field, which
is error prone. The first patch refactors that by replacing all bits with
a single enum. The changes are minimal where each bit change is replaced
with the new state value.

* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
  iavf: remove active_cvlans and active_svlans bitmaps
  iavf: refactor VLAN filter states
====================

Link: https://lore.kernel.org/r/20230407210730.3046149-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'for-net-2023-04-10' of git://git./linux/kernel/git/bluetooth/bluetooth

Luiz Augusto von Dentz says:

====================
bluetooth pull request for net:

- Fix not setting Dath Path for broadcast sink
- Fix not cleaning up on LE Connection failure
- SCO: Fix possible circular locking dependency
- L2CAP: Fix use-after-free in l2cap_disconnect_{req,rsp}
- Fix race condition in hidp_session_thread
- btbcm: Fix logic error in forming the board name
- btbcm: Fix use after free in btsdio_remove

* tag 'for-net-2023-04-10' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
  Bluetooth: L2CAP: Fix use-after-free in l2cap_disconnect_{req,rsp}
  Bluetooth: Set ISO Data Path on broadcast sink
  Bluetooth: hci_conn: Fix possible UAF
  Bluetooth: SCO: Fix possible circular locking dependency sco_sock_getsockopt
  Bluetooth: SCO: Fix possible circular locking dependency on sco_connect_cfm
  bluetooth: btbcm: Fix logic error in forming the board name.
  Bluetooth: btsdio: fix use after free bug in btsdio_remove due to race condition
  Bluetooth: Fix race condition in hidp_session_thread
  Bluetooth: Fix printing errors if LE Connection times out
  Bluetooth: hci_conn: Fix not cleaning up on LE Connection failure
====================

Link: https://lore.kernel.org/r/20230410172718.4067798-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: phy: nxp-c45-tja11xx: add remove callback

Unregister PTP clock when the driver is removed.
Purge the RX and TX skb queues.

Fixes: 514def5dd339 ("phy: nxp-c45-tja11xx: add timestamping support")
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Radu Pirea (OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230406095904.75456-1-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Bluetooth: L2CAP: Fix use-after-free in l2cap_disconnect_{req,rsp}

Similar to commit d0be8347c623 ("Bluetooth: L2CAP: Fix use-after-free
caused by l2cap_chan_put"), just use l2cap_chan_hold_unless_zero to
prevent referencing a channel that is about to be destroyed.

Cc: stable@kernel.org
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Min Li <lm0963hack@gmail.com>

Bluetooth: Set ISO Data Path on broadcast sink

This patch enables ISO data rx on broadcast sink.

Fixes: eca0ae4aea66 ("Bluetooth: Add initial implementation of BIS connections")
Signed-off-by: Claudia Draghicescu <claudia.rosu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Fix possible UAF

This fixes the following trace:

==================================================================
BUG: KASAN: slab-use-after-free in hci_conn_del+0xba/0x3a0
Write of size 8 at addr ffff88800208e9c8 by task iso-tester/31

CPU: 0 PID: 31 Comm: iso-tester Not tainted 6.3.0-rc2-g991aa4a69a47
#4716
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.1-2.fc36
04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x1d/0x70
print_report+0xce/0x610
? __virt_addr_valid+0xd4/0x150
? hci_conn_del+0xba/0x3a0
kasan_report+0xdd/0x110
? hci_conn_del+0xba/0x3a0
hci_conn_del+0xba/0x3a0
hci_conn_hash_flush+0xf2/0x120
hci_dev_close_sync+0x388/0x920
hci_unregister_dev+0x122/0x260
vhci_release+0x4f/0x90
__fput+0x102/0x430
task_work_run+0xf1/0x160
? __pfx_task_work_run+0x10/0x10
? mark_held_locks+0x24/0x90
exit_to_user_mode_prepare+0x170/0x180
syscall_exit_to_user_mode+0x19/0x50
do_syscall_64+0x4e/0x90
entry_SYSCALL_64_after_hwframe+0x70/0xda

Fixes: 0f00cd322d22 ("Bluetooth: Free potentially unfreed SCO connection")
Link: https://syzkaller.appspot.com/bug?extid=8bb72f86fc823817bc5d
Cc: <stable@vger.kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: SCO: Fix possible circular locking dependency sco_sock_getsockopt

This attempts to fix the following trace:

======================================================
WARNING: possible circular locking dependency detected
6.3.0-rc2-g68fcb3a7bf97 #4706 Not tainted
------------------------------------------------------
sco-tester/31 is trying to acquire lock:
ffff8880025b8070 (&hdev->lock){+.+.}-{3:3}, at:
sco_sock_getsockopt+0x1fc/0xa90

but task is already holding lock:
ffff888001eeb130 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0}, at:
sco_sock_getsockopt+0x104/0xa90

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #2 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0}:
       lock_sock_nested+0x32/0x80
       sco_connect_cfm+0x118/0x4a0
       hci_sync_conn_complete_evt+0x1e6/0x3d0
       hci_event_packet+0x55c/0x7c0
       hci_rx_work+0x34c/0xa00
       process_one_work+0x575/0x910
       worker_thread+0x89/0x6f0
       kthread+0x14e/0x180
       ret_from_fork+0x2b/0x50

-> #1 (hci_cb_list_lock){+.+.}-{3:3}:
       __mutex_lock+0x13b/0xcc0
       hci_sync_conn_complete_evt+0x1ad/0x3d0
       hci_event_packet+0x55c/0x7c0
       hci_rx_work+0x34c/0xa00
       process_one_work+0x575/0x910
       worker_thread+0x89/0x6f0
       kthread+0x14e/0x180
       ret_from_fork+0x2b/0x50

-> #0 (&hdev->lock){+.+.}-{3:3}:
       __lock_acquire+0x18cc/0x3740
       lock_acquire+0x151/0x3a0
       __mutex_lock+0x13b/0xcc0
       sco_sock_getsockopt+0x1fc/0xa90
       __sys_getsockopt+0xe9/0x190
       __x64_sys_getsockopt+0x5b/0x70
       do_syscall_64+0x42/0x90
       entry_SYSCALL_64_after_hwframe+0x70/0xda

other info that might help us debug this:

Chain exists of:
  &hdev->lock --> hci_cb_list_lock --> sk_lock-AF_BLUETOOTH-BTPROTO_SCO

Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(sk_lock-AF_BLUETOOTH-BTPROTO_SCO);
                               lock(hci_cb_list_lock);
                               lock(sk_lock-AF_BLUETOOTH-BTPROTO_SCO);
  lock(&hdev->lock);

*** DEADLOCK ***

1 lock held by sco-tester/31:
#0: ffff888001eeb130 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0},
at: sco_sock_getsockopt+0x104/0xa90

Fixes: 248733e87d50 ("Bluetooth: Allow querying of supported offload codecs over SCO socket")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: SCO: Fix possible circular locking dependency on sco_connect_cfm

This attempts to fix the following trace:

======================================================
WARNING: possible circular locking dependency detected
6.3.0-rc2-g0b93eeba4454 #4703 Not tainted
------------------------------------------------------
kworker/u3:0/46 is trying to acquire lock:
ffff888001fd9130 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0}, at:
sco_connect_cfm+0x118/0x4a0

but task is already holding lock:
ffffffff831e3340 (hci_cb_list_lock){+.+.}-{3:3}, at:
hci_sync_conn_complete_evt+0x1ad/0x3d0

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #2 (hci_cb_list_lock){+.+.}-{3:3}:
       __mutex_lock+0x13b/0xcc0
       hci_sync_conn_complete_evt+0x1ad/0x3d0
       hci_event_packet+0x55c/0x7c0
       hci_rx_work+0x34c/0xa00
       process_one_work+0x575/0x910
       worker_thread+0x89/0x6f0
       kthread+0x14e/0x180
       ret_from_fork+0x2b/0x50

-> #1 (&hdev->lock){+.+.}-{3:3}:
       __mutex_lock+0x13b/0xcc0
       sco_sock_connect+0xfc/0x630
       __sys_connect+0x197/0x1b0
       __x64_sys_connect+0x37/0x50
       do_syscall_64+0x42/0x90
       entry_SYSCALL_64_after_hwframe+0x70/0xda

-> #0 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0}:
       __lock_acquire+0x18cc/0x3740
       lock_acquire+0x151/0x3a0
       lock_sock_nested+0x32/0x80
       sco_connect_cfm+0x118/0x4a0
       hci_sync_conn_complete_evt+0x1e6/0x3d0
       hci_event_packet+0x55c/0x7c0
       hci_rx_work+0x34c/0xa00
       process_one_work+0x575/0x910
       worker_thread+0x89/0x6f0
       kthread+0x14e/0x180
       ret_from_fork+0x2b/0x50

other info that might help us debug this:

Chain exists of:
  sk_lock-AF_BLUETOOTH-BTPROTO_SCO --> &hdev->lock --> hci_cb_list_lock

Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(hci_cb_list_lock);
                               lock(&hdev->lock);
                               lock(hci_cb_list_lock);
  lock(sk_lock-AF_BLUETOOTH-BTPROTO_SCO);

*** DEADLOCK ***

4 locks held by kworker/u3:0/46:
#0: ffff8880028d1130 ((wq_completion)hci0#2){+.+.}-{0:0}, at:
process_one_work+0x4c0/0x910
#1: ffff8880013dfde0 ((work_completion)(&hdev->rx_work)){+.+.}-{0:0},
at: process_one_work+0x4c0/0x910
#2: ffff8880025d8070 (&hdev->lock){+.+.}-{3:3}, at:
hci_sync_conn_complete_evt+0xa6/0x3d0
#3: ffffffffb79e3340 (hci_cb_list_lock){+.+.}-{3:3}, at:
hci_sync_conn_complete_evt+0x1ad/0x3d0

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

bluetooth: btbcm: Fix logic error in forming the board name.

This patch fixes an incorrect loop exit condition in code that replaces
'/' symbols in the board name. There might also be a memory corruption
issue here, but it is unlikely to be a real problem.

Cc: <stable@vger.kernel.org>
Signed-off-by: Sasha Finkelstein <fnkl.kernel@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: btsdio: fix use after free bug in btsdio_remove due to race condition

In btsdio_probe, the data->work is bound with btsdio_work. It will be
started in btsdio_send_frame.

If the btsdio_remove runs with a unfinished work, there may be a race
condition that hdev is freed but used in btsdio_work. Fix it by
canceling the work before do cleanup in btsdio_remove.

Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Fix race condition in hidp_session_thread

There is a potential race condition in hidp_session_thread that may
lead to use-after-free. For instance, the timer is active while
hidp_del_timer is called in hidp_session_thread(). After hidp_session_put,
then 'session' will be freed, causing kernel panic when hidp_idle_timeout
is running.

The solution is to use del_timer_sync instead of del_timer.

Here is the call trace:

? hidp_session_probe+0x780/0x780
call_timer_fn+0x2d/0x1e0
__run_timers.part.0+0x569/0x940
hidp_session_probe+0x780/0x780
call_timer_fn+0x1e0/0x1e0
ktime_get+0x5c/0xf0
lapic_next_deadline+0x2c/0x40
clockevents_program_event+0x205/0x320
run_timer_softirq+0xa9/0x1b0
__do_softirq+0x1b9/0x641
__irq_exit_rcu+0xdc/0x190
irq_exit_rcu+0xe/0x20
sysvec_apic_timer_interrupt+0xa1/0xc0

Cc: stable@vger.kernel.org
Signed-off-by: Min Li <lm0963hack@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Fix printing errors if LE Connection times out

This fixes errors like bellow when LE Connection times out since that
is actually not a controller error:

Bluetooth: hci0: Opcode 0x200d failed: -110
Bluetooth: hci0: request failed to create LE connection: err -110

Instead the code shall properly detect if -ETIMEDOUT is returned and
send HCI_OP_LE_CREATE_CONN_CANCEL to give up on the connection.

Link: https://github.com/bluez/bluez/issues/340
Fixes: 8e8b92ee60de ("Bluetooth: hci_sync: Add hci_le_create_conn_sync")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_conn: Fix not cleaning up on LE Connection failure

hci_connect_le_scan_cleanup shall always be invoked to cleanup the
states and re-enable passive scanning if necessary, otherwise it may
cause the pending action to stay active causing multiple attempts to
connect.

Fixes: 9b3628d79b46 ("Bluetooth: hci_sync: Cleanup hci_conn if it cannot be aborted")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Merge branch 'sfp-eeprom'

Ivan Bornyakov says:

====================
net: fix EEPROM read of absent SFP module

The patchset is to improve EEPROM read requests when SFP module is
absent.

ChangeLog:
v1:
https://lore.kernel.org/netdev/20230405153900.747-1-i.bornyakov@metrotek.ru/
v2:
  * reword commit message of "net: sfp: initialize sfp->i2c_block_size
    at sfp allocation"
  * add second patch to eliminate excessive I2C transfers in
    sfp_module_eeprom() and sfp_module_eeprom_by_page()
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: avoid EEPROM read of absent SFP module

If SFP module is not present, it is sensible to fail sfp_module_eeprom()
and sfp_module_eeprom_by_page() early to avoid excessive I2C transfers
which are garanteed to fail.

Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sfp: initialize sfp->i2c_block_size at sfp allocation

sfp->i2c_block_size is initialized at SFP module insertion in
sfp_sm_mod_probe(). Because of that, if SFP module was never inserted
since boot, sfp_read() call will lead to zero-length I2C read attempt,
and not all I2C controllers are happy with zero-length reads.

One way to issue sfp_read() on empty SFP cage is to execute ethtool -m.
If SFP module was never plugged since boot, there will be a zero-length
I2C read attempt.

  # ethtool -m xge0
  i2c i2c-3: adapter quirk: no zero length (addr 0x0050, size 0, read)
  Cannot get Module EEPROM data: Operation not supported

If SFP module was plugged then removed at least once,
sfp->i2c_block_size will be initialized and ethtool -m will fail with
different exit code and without I2C error

  # ethtool -m xge0
  Cannot get Module EEPROM data: Remote I/O error

Fix this by initializing sfp->i2_block_size at struct sfp allocation
stage so no wild sfp_read() could issue zero-length I2C read.

Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Fixes: 0d035bed2a4a ("net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 workaround")
Cc: stable@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8152: Add __GFP_NOWARN to big allocations

When memory is a little tight on my system, it's pretty easy to see
warnings that look like this.

  ksoftirqd/0: page allocation failure: order:3, mode:0x40a20(GFP_ATOMIC|__GFP_COMP), nodemask=(null),cpuset=/,mems_allowed=0
  ...
  Call trace:
   dump_backtrace+0x0/0x1e8
   show_stack+0x20/0x2c
   dump_stack_lvl+0x60/0x78
   dump_stack+0x18/0x38
   warn_alloc+0x104/0x174
   __alloc_pages+0x588/0x67c
   alloc_rx_agg+0xa0/0x190 [r8152 ...]
   r8152_poll+0x270/0x760 [r8152 ...]
   __napi_poll+0x44/0x1ec
   net_rx_action+0x100/0x300
   __do_softirq+0xec/0x38c
   run_ksoftirqd+0x38/0xec
   smpboot_thread_fn+0xb8/0x248
   kthread+0x134/0x154
   ret_from_fork+0x10/0x20

On a fragmented system it's normal that order 3 allocations will
sometimes fail, especially atomic ones. The driver handles these
failures fine and the WARN just creates spam in the logs for this
case. The __GFP_NOWARN flag is exactly for this situation, so add it
to the allocation.

NOTE: my testing is on a 5.15 system, but there should be no reason
that this would be fundamentally different on a mainline kernel.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230406171411.1.I84dbef45786af440fd269b71e9436a96a8e7a152@changeid
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: phy: nxp-c45-tja11xx: fix unsigned long multiplication overflow

Any multiplication between GENMASK(31, 0) and a number bigger than 1
will be truncated because of the overflow, if the size of unsigned long
is 32 bits.

Replaced GENMASK with GENMASK_ULL to make sure that multiplication will
be between 64 bits values.

Cc: <stable@vger.kernel.org> # 5.15+
Fixes: 514def5dd339 ("phy: nxp-c45-tja11xx: add timestamping support")
Signed-off-by: Radu Pirea (OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230406095953.75622-1-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: openvswitch: fix race on port output

assume the following setup on a single machine:
1. An openvswitch instance with one bridge and default flows
2. two network namespaces "server" and "client"
3. two ovs interfaces "server" and "client" on the bridge
4. for each ovs interface a veth pair with a matching name and 32 rx and
   tx queues
5. move the ends of the veth pairs to the respective network namespaces
6. assign ip addresses to each of the veth ends in the namespaces (needs
   to be the same subnet)
7. start some http server on the server network namespace
8. test if a client in the client namespace can reach the http server

when following the actions below the host has a chance of getting a cpu
stuck in a infinite loop:
1. send a large amount of parallel requests to the http server (around
   3000 curls should work)
2. in parallel delete the network namespace (do not delete interfaces or
   stop the server, just kill the namespace)

there is a low chance that this will cause the below kernel cpu stuck
message. If this does not happen just retry.
Below there is also the output of bpftrace for the functions mentioned
in the output.

The series of events happening here is:
1. the network namespace is deleted calling
   `unregister_netdevice_many_notify` somewhere in the process
2. this sets first `NETREG_UNREGISTERING` on both ends of the veth and
   then runs `synchronize_net`
3. it then calls `call_netdevice_notifiers` with `NETDEV_UNREGISTER`
4. this is then handled by `dp_device_event` which calls
   `ovs_netdev_detach_dev` (if a vport is found, which is the case for
   the veth interface attached to ovs)
5. this removes the rx_handlers of the device but does not prevent
   packages to be sent to the device
6. `dp_device_event` then queues the vport deletion to work in
   background as a ovs_lock is needed that we do not hold in the
   unregistration path
7. `unregister_netdevice_many_notify` continues to call
   `netdev_unregister_kobject` which sets `real_num_tx_queues` to 0
8. port deletion continues (but details are not relevant for this issue)
9. at some future point the background task deletes the vport

If after 7. but before 9. a packet is send to the ovs vport (which is
not deleted at this point in time) which forwards it to the
`dev_queue_xmit` flow even though the device is unregistering.
In `skb_tx_hash` (which is called in the `dev_queue_xmit`) path there is
a while loop (if the packet has a rx_queue recorded) that is infinite if
`dev->real_num_tx_queues` is zero.

To prevent this from happening we update `do_output` to handle devices
without carrier the same as if the device is not found (which would
be the code path after 9. is done).

Additionally we now produce a warning in `skb_tx_hash` if we will hit
the infinite loop.

bpftrace (first word is function name):

__dev_queue_xmit server: real_num_tx_queues: 1, cpu: 2, pid: 28024, tid: 28024, skb_addr: 0xffff9edb6f207000, reg_state: 1
netdev_core_pick_tx server: addr: 0xffff9f0a46d4a000 real_num_tx_queues: 1, cpu: 2, pid: 28024, tid: 28024, skb_addr: 0xffff9edb6f207000, reg_state: 1
dp_device_event server: real_num_tx_queues: 1 cpu 9, pid: 21024, tid: 21024, event 2, reg_state: 1
synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024
synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024
synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024
synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024
dp_device_event server: real_num_tx_queues: 1 cpu 9, pid: 21024, tid: 21024, event 6, reg_state: 2
ovs_netdev_detach_dev server: real_num_tx_queues: 1 cpu 9, pid: 21024, tid: 21024, reg_state: 2
netdev_rx_handler_unregister server: real_num_tx_queues: 1, cpu: 9, pid: 21024, tid: 21024, reg_state: 2
synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024
netdev_rx_handler_unregister ret server: real_num_tx_queues: 1, cpu: 9, pid: 21024, tid: 21024, reg_state: 2
dp_device_event server: real_num_tx_queues: 1 cpu 9, pid: 21024, tid: 21024, event 27, reg_state: 2
dp_device_event server: real_num_tx_queues: 1 cpu 9, pid: 21024, tid: 21024, event 22, reg_state: 2
dp_device_event server: real_num_tx_queues: 1 cpu 9, pid: 21024, tid: 21024, event 18, reg_state: 2
netdev_unregister_kobject: real_num_tx_queues: 1, cpu: 9, pid: 21024, tid: 21024
synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024
ovs_vport_send server: real_num_tx_queues: 0, cpu: 2, pid: 28024, tid: 28024, skb_addr: 0xffff9edb6f207000, reg_state: 2
__dev_queue_xmit server: real_num_tx_queues: 0, cpu: 2, pid: 28024, tid: 28024, skb_addr: 0xffff9edb6f207000, reg_state: 2
netdev_core_pick_tx server: addr: 0xffff9f0a46d4a000 real_num_tx_queues: 0, cpu: 2, pid: 28024, tid: 28024, skb_addr: 0xffff9edb6f207000, reg_state: 2
broken device server: real_num_tx_queues: 0, cpu: 2, pid: 28024, tid: 28024
ovs_dp_detach_port server: real_num_tx_queues: 0 cpu 9, pid: 9124, tid: 9124, reg_state: 2
synchronize_rcu_expedited: cpu 9, pid: 33604, tid: 33604

stuck message:

watchdog: BUG: soft lockup - CPU#5 stuck for 26s! [curl:1929279]
Modules linked in: veth pktgen bridge stp llc ip_set_hash_net nft_counter xt_set nft_compat nf_tables ip_set_hash_ip ip_set nfnetlink_cttimeout nfnetlink openvswitch nsh nf_conncount nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 tls binfmt_misc nls_iso8859_1 input_leds joydev serio_raw dm_multipath scsi_dh_rdac scsi_dh_emc scsi_dh_alua sch_fq_codel drm efi_pstore virtio_rng ip_tables x_tables autofs4 btrfs blake2b_generic zstd_compress raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c raid1 raid0 multipath linear hid_generic usbhid hid crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel virtio_net ahci net_failover crypto_simd cryptd psmouse libahci virtio_blk failover
CPU: 5 PID: 1929279 Comm: curl Not tainted 5.15.0-67-generic #74-Ubuntu
Hardware name: OpenStack Foundation OpenStack Nova, BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
RIP: 0010:netdev_pick_tx+0xf1/0x320
Code: 00 00 8d 48 ff 0f b7 c1 66 39 ca 0f 86 e9 01 00 00 45 0f b7 ff 41 39 c7 0f 87 5b 01 00 00 44 29 f8 41 39 c7 0f 87 4f 01 00 00 <eb> f2 0f 1f 44 00 00 49 8b 94 24 28 04 00 00 48 85 d2 0f 84 53 01
RSP: 0018:ffffb78b40298820 EFLAGS: 00000246
RAX: 0000000000000000 RBX: ffff9c8773adc2e0 RCX: 000000000000083f
RDX: 0000000000000000 RSI: ffff9c8773adc2e0 RDI: ffff9c870a25e000
RBP: ffffb78b40298858 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff9c870a25e000
R13: ffff9c870a25e000 R14: ffff9c87fe043480 R15: 0000000000000000
FS:  00007f7b80008f00(0000) GS:ffff9c8e5f740000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f7b80f6a0b0 CR3: 0000000329d66000 CR4: 0000000000350ee0
Call Trace:
<IRQ>
netdev_core_pick_tx+0xa4/0xb0
__dev_queue_xmit+0xf8/0x510
? __bpf_prog_exit+0x1e/0x30
dev_queue_xmit+0x10/0x20
ovs_vport_send+0xad/0x170 [openvswitch]
do_output+0x59/0x180 [openvswitch]
do_execute_actions+0xa80/0xaa0 [openvswitch]
? kfree+0x1/0x250
? kfree+0x1/0x250
? kprobe_perf_func+0x4f/0x2b0
? flow_lookup.constprop.0+0x5c/0x110 [openvswitch]
ovs_execute_actions+0x4c/0x120 [openvswitch]
ovs_dp_process_packet+0xa1/0x200 [openvswitch]
? ovs_ct_update_key.isra.0+0xa8/0x120 [openvswitch]
? ovs_ct_fill_key+0x1d/0x30 [openvswitch]
? ovs_flow_key_extract+0x2db/0x350 [openvswitch]
ovs_vport_receive+0x77/0xd0 [openvswitch]
? __htab_map_lookup_elem+0x4e/0x60
? bpf_prog_680e8aff8547aec1_kfree+0x3b/0x714
? trace_call_bpf+0xc8/0x150
? kfree+0x1/0x250
? kfree+0x1/0x250
? kprobe_perf_func+0x4f/0x2b0
? kprobe_perf_func+0x4f/0x2b0
? __mod_memcg_lruvec_state+0x63/0xe0
netdev_port_receive+0xc4/0x180 [openvswitch]
? netdev_port_receive+0x180/0x180 [openvswitch]
netdev_frame_hook+0x1f/0x40 [openvswitch]
__netif_receive_skb_core.constprop.0+0x23d/0xf00
__netif_receive_skb_one_core+0x3f/0xa0
__netif_receive_skb+0x15/0x60
process_backlog+0x9e/0x170
__napi_poll+0x33/0x180
net_rx_action+0x126/0x280
? ttwu_do_activate+0x72/0xf0
__do_softirq+0xd9/0x2e7
? rcu_report_exp_cpu_mult+0x1b0/0x1b0
do_softirq+0x7d/0xb0
</IRQ>
<TASK>
__local_bh_enable_ip+0x54/0x60
ip_finish_output2+0x191/0x460
__ip_finish_output+0xb7/0x180
ip_finish_output+0x2e/0xc0
ip_output+0x78/0x100
? __ip_finish_output+0x180/0x180
ip_local_out+0x5e/0x70
__ip_queue_xmit+0x184/0x440
? tcp_syn_options+0x1f9/0x300
ip_queue_xmit+0x15/0x20
__tcp_transmit_skb+0x910/0x9c0
? __mod_memcg_state+0x44/0xa0
tcp_connect+0x437/0x4e0
? ktime_get_with_offset+0x60/0xf0
tcp_v4_connect+0x436/0x530
__inet_stream_connect+0xd4/0x3a0
? kprobe_perf_func+0x4f/0x2b0
? aa_sk_perm+0x43/0x1c0
inet_stream_connect+0x3b/0x60
__sys_connect_file+0x63/0x70
__sys_connect+0xa6/0xd0
? setfl+0x108/0x170
? do_fcntl+0xe8/0x5a0
__x64_sys_connect+0x18/0x20
do_syscall_64+0x5c/0xc0
? __x64_sys_fcntl+0xa9/0xd0
? exit_to_user_mode_prepare+0x37/0xb0
? syscall_exit_to_user_mode+0x27/0x50
? do_syscall_64+0x69/0xc0
? __sys_setsockopt+0xea/0x1e0
? exit_to_user_mode_prepare+0x37/0xb0
? syscall_exit_to_user_mode+0x27/0x50
? __x64_sys_setsockopt+0x1f/0x30
? do_syscall_64+0x69/0xc0
? irqentry_exit+0x1d/0x30
? exc_page_fault+0x89/0x170
entry_SYSCALL_64_after_hwframe+0x61/0xcb
RIP: 0033:0x7f7b8101c6a7
Code: 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 2a 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 18 89 54 24 0c 48 89 34 24 89
RSP: 002b:00007ffffd6b2198 EFLAGS: 00000246 ORIG_RAX: 000000000000002a
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f7b8101c6a7
RDX: 0000000000000010 RSI: 00007ffffd6b2360 RDI: 0000000000000005
RBP: 0000561f1370d560 R08: 00002795ad21d1ac R09: 0030312e302e302e
R10: 00007ffffd73f080 R11: 0000000000000246 R12: 0000561f1370c410
R13: 0000000000000000 R14: 0000000000000005 R15: 0000000000000000
</TASK>

Fixes: 7f8a436eaa2c ("openvswitch: Add conntrack action")
Co-developed-by: Luca Czesla <luca.czesla@mail.schwarz>
Signed-off-by: Luca Czesla <luca.czesla@mail.schwarz>
Signed-off-by: Felix Huettner <felix.huettner@mail.schwarz>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/ZC0pBXBAgh7c76CA@kernel-bug-kernel-bug
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'for-netdev' of https://git./linux/kernel/git/bpf/bpf

Daniel Borkmann says:

====================
pull-request: bpf 2023-04-08

We've added 4 non-merge commits during the last 11 day(s) which contain
a total of 5 files changed, 39 insertions(+), 6 deletions(-).

The main changes are:

1) Fix BPF TCP socket iterator to use correct helper for dropping
   socket's refcount, that is, sock_gen_put instead of sock_put,
   from Martin KaFai Lau.

2) Fix a BTI exception splat in BPF trampoline-generated code on arm64,
   from Xu Kuohai.

3) Fix a LongArch JIT error from missing BPF_NOSPEC no-op, from George Guo.

4) Fix dynamic XDP feature detection of veth in xdp_redirect selftest,
   from Lorenzo Bianconi.

* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
  selftests/bpf: fix xdp_redirect xdp-features selftest for veth driver
  bpf, arm64: Fixed a BTI error on returning to patched function
  LoongArch, bpf: Fix jit to skip speculation barrier opcode
  bpf: tcp: Use sock_gen_put instead of sock_put in bpf_iter_tcp
====================

Link: https://lore.kernel.org/r/20230407224642.30906-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

iavf: remove active_cvlans and active_svlans bitmaps

The VLAN filters info is currently being held in a list and 2 bitmaps
(active_cvlans and active_svlans). We are experiencing some racing where
data is not in sync in the list and bitmaps. For example, the VLAN is
initially added to the list but only when the PF replies, it is added to
the bitmap. If a user adds many V2 VLANS before the PF responds:

    while [ $((i++)) ]
        ip l add l eth0 name eth0.$i type vlan id $i

we might end up with more VLAN list entries than the designated limit.
Also, The "ip link show" will show more links added than the PF limit.

On the other and, the bitmaps are only used to check the number of VLAN
filters and to re-enable the filters when the interface goes from DOWN to
UP.

This patch gets rid of the bitmaps and uses the list only. To do that,
the states of the VLAN filter are modified:
1 - IAVF_VLAN_REMOVE: the entry needs to be totally removed after informing
  the PF. This is the "ip link del eth0.$i" path.
2 - IAVF_VLAN_DISABLE: (new) the netdev went down. The filter needs to be
  removed from the PF and then marked INACTIVE.
3 - IAVF_VLAN_INACTIVE: (new) no PF filter exists, but the user did not
  delete the VLAN.

Fixes: 48ccc43ecf10 ("iavf: Add support VIRTCHNL_VF_OFFLOAD_VLAN_V2 during netdev config")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf: refactor VLAN filter states

The VLAN filter states are currently being saved as individual bits.
This is error prone as multiple bits might be mistakenly set.

Fix by replacing the bits with a single state enum. Also, add an
"ACTIVE" state for filters that are accepted by the PF.

Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Merge branch 'bonding-ns-validation-fixes'

Hangbin Liu says:

====================
bonding: fix ns validation on backup slaves

The first patch fixed a ns validation issue on backup slaves. The second
patch re-format the bond option test and add a test lib file. The third
patch add the arp validate regression test for the kernel patch.

Here is the new bonding option test without the kernel fix:

]# ./bond_options.sh
TEST: prio (active-backup miimon primary_reselect 0)           [ OK ]
TEST: prio (active-backup miimon primary_reselect 1)           [ OK ]
TEST: prio (active-backup miimon primary_reselect 2)           [ OK ]
TEST: prio (active-backup arp_ip_target primary_reselect 0)    [ OK ]
TEST: prio (active-backup arp_ip_target primary_reselect 1)    [ OK ]
TEST: prio (active-backup arp_ip_target primary_reselect 2)    [ OK ]
TEST: prio (active-backup ns_ip6_target primary_reselect 0)    [ OK ]
TEST: prio (active-backup ns_ip6_target primary_reselect 1)    [ OK ]
TEST: prio (active-backup ns_ip6_target primary_reselect 2)    [ OK ]
TEST: prio (balance-tlb miimon primary_reselect 0)             [ OK ]
TEST: prio (balance-tlb miimon primary_reselect 1)             [ OK ]
TEST: prio (balance-tlb miimon primary_reselect 2)             [ OK ]
TEST: prio (balance-tlb arp_ip_target primary_reselect 0)      [ OK ]
TEST: prio (balance-tlb arp_ip_target primary_reselect 1)      [ OK ]
TEST: prio (balance-tlb arp_ip_target primary_reselect 2)      [ OK ]
TEST: prio (balance-tlb ns_ip6_target primary_reselect 0)      [ OK ]
TEST: prio (balance-tlb ns_ip6_target primary_reselect 1)      [ OK ]
TEST: prio (balance-tlb ns_ip6_target primary_reselect 2)      [ OK ]
TEST: prio (balance-alb miimon primary_reselect 0)             [ OK ]
TEST: prio (balance-alb miimon primary_reselect 1)             [ OK ]
TEST: prio (balance-alb miimon primary_reselect 2)             [ OK ]
TEST: prio (balance-alb arp_ip_target primary_reselect 0)      [ OK ]
TEST: prio (balance-alb arp_ip_target primary_reselect 1)      [ OK ]
TEST: prio (balance-alb arp_ip_target primary_reselect 2)      [ OK ]
TEST: prio (balance-alb ns_ip6_target primary_reselect 0)      [ OK ]
TEST: prio (balance-alb ns_ip6_target primary_reselect 1)      [ OK ]
TEST: prio (balance-alb ns_ip6_target primary_reselect 2)      [ OK ]
TEST: arp_validate (active-backup arp_ip_target arp_validate 0)  [ OK ]
TEST: arp_validate (active-backup arp_ip_target arp_validate 1)  [ OK ]
TEST: arp_validate (active-backup arp_ip_target arp_validate 2)  [ OK ]
TEST: arp_validate (active-backup arp_ip_target arp_validate 3)  [ OK ]
TEST: arp_validate (active-backup arp_ip_target arp_validate 4)  [ OK ]
TEST: arp_validate (active-backup arp_ip_target arp_validate 5)  [ OK ]
TEST: arp_validate (active-backup arp_ip_target arp_validate 6)  [ OK ]
TEST: arp_validate (active-backup ns_ip6_target arp_validate 0)  [ OK ]
TEST: arp_validate (active-backup ns_ip6_target arp_validate 1)  [ OK ]
TEST: arp_validate (interface eth1 mii_status DOWN)                 [FAIL]
TEST: arp_validate (interface eth2 mii_status DOWN)                 [FAIL]
TEST: arp_validate (active-backup ns_ip6_target arp_validate 2)  [FAIL]
TEST: arp_validate (interface eth1 mii_status DOWN)                 [FAIL]
TEST: arp_validate (interface eth2 mii_status DOWN)                 [FAIL]
TEST: arp_validate (active-backup ns_ip6_target arp_validate 3)  [FAIL]
TEST: arp_validate (active-backup ns_ip6_target arp_validate 4)  [ OK ]
TEST: arp_validate (active-backup ns_ip6_target arp_validate 5)  [ OK ]
TEST: arp_validate (interface eth1 mii_status DOWN)                 [FAIL]
TEST: arp_validate (interface eth2 mii_status DOWN)                 [FAIL]
TEST: arp_validate (active-backup ns_ip6_target arp_validate 6)  [FAIL]

Here is the test result after the kernel fix:
TEST: arp_validate (active-backup arp_ip_target arp_validate 0)  [ OK ]
TEST: arp_validate (active-backup arp_ip_target arp_validate 1)  [ OK ]
TEST: arp_validate (active-backup arp_ip_target arp_validate 2)  [ OK ]
TEST: arp_validate (active-backup arp_ip_target arp_validate 3)  [ OK ]
TEST: arp_validate (active-backup arp_ip_target arp_validate 4)  [ OK ]
TEST: arp_validate (active-backup arp_ip_target arp_validate 5)  [ OK ]
TEST: arp_validate (active-backup arp_ip_target arp_validate 6)  [ OK ]
TEST: arp_validate (active-backup ns_ip6_target arp_validate 0)  [ OK ]
TEST: arp_validate (active-backup ns_ip6_target arp_validate 1)  [ OK ]
TEST: arp_validate (active-backup ns_ip6_target arp_validate 2)  [ OK ]
TEST: arp_validate (active-backup ns_ip6_target arp_validate 3)  [ OK ]
TEST: arp_validate (active-backup ns_ip6_target arp_validate 4)  [ OK ]
TEST: arp_validate (active-backup ns_ip6_target arp_validate 5)  [ OK ]
TEST: arp_validate (active-backup ns_ip6_target arp_validate 6)  [ OK ]
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: bonding: add arp validate test

This patch add bonding arp validate tests with mode active backup,
monitor arp_ip_target and ns_ip6_target. It also checks mii_status
to make sure all slaves are UP.

Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: bonding: re-format bond option tests

To improve the testing process for bond options, A new bond topology lib
is added to our testing setup. The current option_prio.sh file will be
renamed to bond_options.sh so that all bonding options can be tested here.
Specifically, for priority testing, we will run all tests using modes
1, 5, and 6. These changes will help us streamline the testing process
and ensure that our bond options are rigorously evaluated.

Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: fix ns validation on backup slaves

When arp_validate is set to 2, 3, or 6, validation is performed for
backup slaves as well. As stated in the bond documentation, validation
involves checking the broadcast ARP request sent out via the active
slave. This helps determine which slaves are more likely to function in
the event of an active slave failure.

However, when the target is an IPv6 address, the NS message sent from
the active interface is not checked on backup slaves. Additionally,
based on the bond_arp_rcv() rule b, we must reverse the saddr and daddr
when checking the NS message.

Note that when checking the NS message, the destination address is a
multicast address. Therefore, we must convert the target address to
solicited multicast in the bond_get_targets_ip6() function.

Prior to the fix, the backup slaves had a mii status of "down", but
after the fix, all of the slaves' mii status was updated to "UP".

Fixes: 4e24be018eb9 ("bonding: add new parameter ns_targets")
Reviewed-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: restrict net.ipv4.tcp_app_win

UBSAN: shift-out-of-bounds in net/ipv4/tcp_input.c:555:23
shift exponent 255 is too large for 32-bit type 'int'
CPU: 1 PID: 7907 Comm: ssh Not tainted 6.3.0-rc4-00161-g62bad54b26db-dirty #206
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x136/0x150
__ubsan_handle_shift_out_of_bounds+0x21f/0x5a0
tcp_init_transfer.cold+0x3a/0xb9
tcp_finish_connect+0x1d0/0x620
tcp_rcv_state_process+0xd78/0x4d60
tcp_v4_do_rcv+0x33d/0x9d0
__release_sock+0x133/0x3b0
release_sock+0x58/0x1b0

'maxwin' is int, shifting int for 32 or more bits is undefined behaviour.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

niu: Fix missing unwind goto in niu_alloc_channels()

Smatch reports: drivers/net/ethernet/sun/niu.c:4525
niu_alloc_channels() warn: missing unwind goto?

If niu_rbr_fill() fails, then we are directly returning 'err' without
freeing the channels.

Fix this by changing direct return to a goto 'out_err'.

Fixes: a3138df9f20e ("[NIU]: Add Sun Neptune ethernet driver.")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'net-6.3-rc6-2' of git://git./linux/kernel/git/netdev/net

Pull networking fixes from Jakub Kicinski:
"Including fixes from wireless and can.

  Current release - regressions:

   - wifi: mac80211:
      - fix potential null pointer dereference
      - fix receiving mesh packets in forwarding=0 networks
      - fix mesh forwarding

  Current release - new code bugs:

   - virtio/vsock: fix leaks due to missing skb owner

  Previous releases - regressions:

   - raw: fix NULL deref in raw_get_next().

   - sctp: check send stream number after wait_for_sndbuf

   - qrtr:
      - fix a refcount bug in qrtr_recvmsg()
      - do not do DEL_SERVER broadcast after DEL_CLIENT

   - wifi: brcmfmac: fix SDIO suspend/resume regression

   - wifi: mt76: fix use-after-free in fw features query.

   - can: fix race between isotp_sendsmg() and isotp_release()

   - eth: mtk_eth_soc: fix remaining throughput regression

   - eth: ice: reset FDIR counter in FDIR init stage

  Previous releases - always broken:

   - core: don't let netpoll invoke NAPI if in xmit context

   - icmp: guard against too small mtu

   - ipv6: fix an uninit variable access bug in __ip6_make_skb()

   - wifi: mac80211: fix the size calculation of
     ieee80211_ie_len_eht_cap()

   - can: fix poll() to not report false EPOLLOUT events

   - eth: gve: secure enough bytes in the first TX desc for all TCP
     pkts"

* tag 'net-6.3-rc6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (47 commits)
  net: stmmac: check fwnode for phy device before scanning for phy
  net: stmmac: Add queue reset into stmmac_xdp_open() function
  selftests: net: rps_default_mask.sh: delete veth link specifically
  net: fec: make use of MDIO C45 quirk
  can: isotp: fix race between isotp_sendsmg() and isotp_release()
  can: isotp: isotp_ops: fix poll() to not report false EPOLLOUT events
  can: isotp: isotp_recvmsg(): use sock_recv_cmsgs() to get SOCK_RXQ_OVFL infos
  can: j1939: j1939_tp_tx_dat_new(): fix out-of-bounds memory access
  gve: Secure enough bytes in the first TX desc for all TCP pkts
  netlink: annotate lockless accesses to nlk->max_recvmsg_len
  ethtool: reset #lanes when lanes is omitted
  ping: Fix potentail NULL deref for /proc/net/icmp.
  raw: Fix NULL deref in raw_get_next().
  ice: Reset FDIR counter in FDIR init stage
  ice: fix wrong fallback logic for FDIR
  net: stmmac: fix up RX flow hash indirection table when setting channels
  net: ethernet: ti: am65-cpsw: Fix mdio cleanup in probe
  wifi: mt76: ignore key disable commands
  wifi: ath11k: reduce the MHI timeout to 20s
  ipv6: Fix an uninit variable access bug in __ip6_make_skb()
  ...

Merge tag 'linux-kselftest-fixes-6.3-rc6' of git://git./linux/kernel/git/shuah/linux-kselftest

Pull Kselftest fixes from Shuah Khan:
"One single fix to mount_setattr_test build failure"

* tag 'linux-kselftest-fixes-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests mount: Fix mount_setattr_test builds failed

Merge tag 'for-linus-iommufd' of git://git./linux/kernel/git/jgg/iommufd

Pull iommufd fixes from Jason Gunthorpe:

- An invalid VA range can be be put in a pages and eventually trigger
   WARN_ON, reject it early

- Use of the wrong start index value when doing the complex batch carry
   scheme

- Wrong store ordering resulting in corrupting data used in a later
   calculation that corrupted the batch structure during carry

* tag 'for-linus-iommufd' of git://git.kernel.org/pub/scm/linux/kernel/git/jgg/iommufd:
  iommufd: Do not corrupt the pfn list when doing batch carry
  iommufd: Fix unpinning of pages when an access is present
  iommufd: Check for uptr overflow

Merge tag 'pwm/for-6.3-rc6' of git://git./linux/kernel/git/thierry.reding/linux-pwm

Pull pwm fixes from Thierry Reding:
"These are some fixes to make sure the PWM state structure is always
  initialized to a known state.

  Prior to this it could happen in some situations that random data from
  the stack would leak into the data structure and cause subtle bugs"

* tag 'pwm/for-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
  pwm: Zero-initialize the pwm_state passed to driver's .get_state()
  pwm: meson: Explicitly set .polarity in .get_state()
  pwm: sprd: Explicitly set .polarity in .get_state()
  pwm: iqs620a: Explicitly set .polarity in .get_state()
  pwm: cros-ec: Explicitly set .polarity in .get_state()
  pwm: hibvt: Explicitly set .polarity in .get_state()

Merge tag 'drm-fixes-2023-04-06' of git://anongit.freedesktop.org/drm/drm

Pull drm fixes from Daniel Vetter:
"Mostly i915 fixes: dp mst for compression/dsc, perf ioctl uaf, ctx rpm
  accounting, gt reset vs huc loading.

  And a few individual driver fixes: ivpu dma fence&suspend, panfrost
  mmap, nouveau color depth"

* tag 'drm-fixes-2023-04-06' of git://anongit.freedesktop.org/drm/drm:
  accel/ivpu: Fix S3 system suspend when not idle
  accel/ivpu: Add dma fence to command buffers only
  drm/i915: Fix context runtime accounting
  drm/i915: fix race condition UAF in i915_perf_add_config_ioctl
  drm/i915: Use compressed bpp when calculating m/n value for DP MST DSC
  drm/i915/huc: Cancel HuC delayed load timer on reset.
  drm/i915/ttm: fix sparse warning
  drm/panfrost: Fix the panfrost_mmu_map_fault_addr() error path
  drm/nouveau/disp: Support more modes by checking with lower bpc

Merge tag 'sound-6.3-rc6' of git://git./linux/kernel/git/tiwai/sound

Pull sound fixes from Takashi Iwai:
"The majority of changes here are various fixes for Intel drivers,
  and there is a change in ASoC PCM core for the format constraints.

  In addition, a workaround for HD-audio HDMI regressions and usual
  HD-audio quirks are found"

* tag 'sound-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/hdmi: Preserve the previous PCM device upon re-enablement
  ALSA: hda/realtek: Add quirk for Clevo X370SNW
  ALSA: hda/realtek: fix mute/micmute LEDs for a HP ProBook
  ASoC: SOF: avoid a NULL dereference with unsupported widgets
  ASoC: da7213.c: add missing pm_runtime_disable()
  ASoC: hdac_hdmi: use set_stream() instead of set_tdm_slots()
  ASoC: codecs: lpass: fix the order or clks turn off during suspend
  ASoC: Intel: bytcr_rt5640: Add quirk for the Acer Iconia One 7 B1-750
  ASoC: SOF: ipc4: Ensure DSP is in D0I0 during sof_ipc4_set_get_data()
  ASoC: amd: yc: Add DMI entries to support Victus by HP Laptop 16-e1xxx (8A22)
  ASoC: soc-pcm: fix hw->formats cleared by soc_pcm_hw_init() for dpcm
  ASoC: Intel: soc-acpi: add table for Intel 'Rooks County' NUC M15
  ASOC: Intel: sof_sdw: add quirk for Intel 'Rooks County' NUC M15

Merge tag 'platform-drivers-x86-v6.3-5' of git://git./linux/kernel/git/pdx86/platform-drivers-x86

Pull x86 platform driver fixes from Hans de Goede:

-  more think-lmi fixes

-  one DMI quirk addition

* tag 'platform-drivers-x86-v6.3-5' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
  platform/x86: thinkpad_acpi: Add missing T14s Gen1 type to s2idle quirk list
  platform/x86: think-lmi: Clean up display of current_value on Thinkstation
  platform/x86: think-lmi: Fix memory leaks when parsing ThinkStation WMI strings
  platform/x86: think-lmi: Fix memory leak when showing current settings

Merge tag 'asm-generic-fixes-6.3' of git://git./linux/kernel/git/arnd/asm-generic

Pull asm-generic fixes from Arnd Bergmann:
"These are minor fixes to address false-positive build warnings:

  Some of the less common I/O accessors are missing __force casts and
  cause sparse warnings for their implied byteswap, and a recent change
  to __generic_cmpxchg_local() causes a warning about constant integer
  truncation"

* tag 'asm-generic-fixes-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
  asm-generic: avoid __generic_cmpxchg_local warnings
  asm-generic/io.h: suppress endianness warnings for relaxed accessors
  asm-generic/io.h: suppress endianness warnings for readq() and writeq()

selftests/bpf: fix xdp_redirect xdp-features selftest for veth driver

xdp-features supported by veth driver are no more static, but they
depends on veth configuration (e.g. if GRO is enabled/disabled or
TX/RX queue configuration). Take it into account in xdp_redirect
xdp-features selftest for veth driver.

Fixes: fccca038f300 ("veth: take into account device reconfiguration for xdp_features flag")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/bc35455cfbb1d4f7f52536955ded81ad47d8dc54.1680777371.git.lorenzo@kernel.org
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>

net: stmmac: check fwnode for phy device before scanning for phy

Some DT devices already have phy device configured in the DT/ACPI.
Current implementation scans for a phy unconditionally even though
there is a phy listed in the DT/ACPI and already attached.

We should check the fwnode if there is any phy device listed in
fwnode and decide whether to scan for a phy to attach to.

Fixes: fe2cfbc96803 ("net: stmmac: check if MAC needs to attach to a PHY")
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/lkml/20230403212434.296975-1-martin.blumenstingl@googlemail.com/
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Shahab Vahedi <shahab@synopsys.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Link: https://lore.kernel.org/r/20230406024541.3556305-1-michael.wei.hong.sit@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: stmmac: Add queue reset into stmmac_xdp_open() function

Queue reset was moved out from __init_dma_rx_desc_rings() and
__init_dma_tx_desc_rings() functions. Thus, the driver fails to transmit
and receive packet after XDP prog setup.

This commit adds the missing queue reset into stmmac_xdp_open() function.

Fixes: f9ec5723c3db ("net: ethernet: stmicro: stmmac: move queue reset to dedicated functions")
Cc: <stable@vger.kernel.org> # 6.0+
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://lore.kernel.org/r/20230404044823.3226144-1-yoong.siang.song@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

selftests: net: rps_default_mask.sh: delete veth link specifically

When deleting the netns and recreating a new one while re-adding the
veth interface, there is a small window of time during which the old
veth interface has not yet been removed. This can cause the new addition
to fail. To resolve this issue, we can either wait for a short while to
ensure that the old veth interface is deleted, or we can specifically
remove the veth interface.

Before this patch:
  # ./rps_default_mask.sh
  empty rps_default_mask                                      [ ok ]
  changing rps_default_mask dont affect existing devices      [ ok ]
  changing rps_default_mask dont affect existing netns        [ ok ]
  changing rps_default_mask affect newly created devices      [ ok ]
  changing rps_default_mask don't affect newly child netns[II][ ok ]
  rps_default_mask is 0 by default in child netns             [ ok ]
  RTNETLINK answers: File exists
  changing rps_default_mask in child ns don't affect the main one[ ok ]
  cat: /sys/class/net/vethC11an1/queues/rx-0/rps_cpus: No such file or directory
  changing rps_default_mask in child ns affects new childns devices./rps_default_mask.sh: line 36: [: -eq: unary operator expected
  [fail] expected 1 found
  changing rps_default_mask in child ns don't affect existing devices[ ok ]

After this patch:
  # ./rps_default_mask.sh
  empty rps_default_mask                                      [ ok ]
  changing rps_default_mask dont affect existing devices      [ ok ]
  changing rps_default_mask dont affect existing netns        [ ok ]
  changing rps_default_mask affect newly created devices      [ ok ]
  changing rps_default_mask don't affect newly child netns[II][ ok ]
  rps_default_mask is 0 by default in child netns             [ ok ]
  changing rps_default_mask in child ns don't affect the main one[ ok ]
  changing rps_default_mask in child ns affects new childns devices[ ok ]
  changing rps_default_mask in child ns don't affect existing devices[ ok ]

Fixes: 3a7d84eae03b ("self-tests: more rps self tests")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20230404072411.879476-1-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: fec: make use of MDIO C45 quirk

Not all fec MDIO bus drivers support C45 mode transactions. The older fec
hardware block in many ColdFire SoCs does not appear to support them, at
least according to most of the different ColdFire SoC reference manuals.
The bits used to generate C45 access on the iMX parts, in the OP field
of the MMFR register, are documented as generating non-compliant MII
frames (it is not documented as to exactly how they are non-compliant).

Commit 8d03ad1ab0b0 ("net: fec: Separate C22 and C45 transactions")
means the fec driver will always register c45 MDIO read and write
methods. During probe these will always be accessed now generating
non-compliant MII accesses on ColdFire based devices.

Add a quirk define, FEC_QUIRK_HAS_MDIO_C45, that can be used to
distinguish silicon that supports MDIO C45 framing or not. Add this to
all the existing iMX quirks, so they will be behave as they do now (*).

(*) it seems that some iMX parts may not support C45 transactions either.
The iMX25 and iMX50 Reference Manuals contain similar wording to
the ColdFire Reference Manuals on this.

Fixes: 8d03ad1ab0b0 ("net: fec: Separate C22 and C45 transactions")
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230404052207.3064861-1-gerg@linux-m68k.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'wireless-2023-04-05' of git://git./linux/kernel/git/wireless/wireless

Kalle Valo says:

====================
wireless fixes for v6.3

mt76 has a fix for leaking cleartext frames on a certain scenario and
two firmware file handling related fixes. For brcmfmac we have a fix
for an older SDIO suspend regression and for ath11k avoiding a kernel
crash during hibernation with SUSE kernels.

* tag 'wireless-2023-04-05' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
  wifi: mt76: ignore key disable commands
  wifi: ath11k: reduce the MHI timeout to 20s
  wifi: mt76: mt7921: fix fw used for offload check for mt7922
  wifi: mt76: mt7921: Fix use-after-free in fw features query.
  wifi: brcmfmac: Fix SDIO suspend/resume regression
====================

Link: https://lore.kernel.org/r/20230405105536.4E946C433D2@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'linux-can-fixes-for-6.3-20230405' of git://git./linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2023-04-05

The first patch is by Oleksij Rempel and fixes a out-of-bounds memory
access in the j1939 protocol.

The remaining 3 patches target the ISOTP protocol. Oliver Hartkopp
fixes the ISOTP protocol to pass information about dropped PDUs to the
user space via control messages. Michal Sojka's patch fixes poll() to
not forward false EPOLLOUT events. And Oliver Hartkopp fixes a race
condition between isotp_sendsmg() and isotp_release().

* tag 'linux-can-fixes-for-6.3-20230405' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
  can: isotp: fix race between isotp_sendsmg() and isotp_release()
  can: isotp: isotp_ops: fix poll() to not report false EPOLLOUT events
  can: isotp: isotp_recvmsg(): use sock_recv_cmsgs() to get SOCK_RXQ_OVFL infos
  can: j1939: j1939_tp_tx_dat_new(): fix out-of-bounds memory access
====================

Link: https://lore.kernel.org/r/20230405092444.1802340-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch '100GbE' of git://git./linux/kernel/git/tnguy/net-queue

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2023-04-04 (ice)

This series contains updates to ice driver only.

Simei adjusts error path on adding VF Flow Director filters that were
not releasing all resources.

Lingyu adds setting/resetting of VF Flow Director filters counters
during initialization.

* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Reset FDIR counter in FDIR init stage
ice: fix wrong fallback logic for FDIR
====================

Link: https://lore.kernel.org/r/20230404172306.450880-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'drm-misc-fixes-2023-04-05' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes

Short summary of fixes pull:

* ivpu: DMA fence and suspend fixes
* nouveau: Color-depth fixes
* panfrost: Fix mmap error handling

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230405182855.GA1551@linux-uq9g

Merge tag 'trace-v6.3-rc5' of git://git./linux/kernel/git/trace/linux-trace

Pull tracing fixes from Steven Rostedt:

- Fix timerlat notification, as it was not triggering the notify to
   users when a new max latency was hit.

- Do not trigger max latency if the tracing is off.

   When tracing is off, the ring buffer is not updated, it does not make
   sense to notify when there's a new max latency detected by the
   tracer, as why that latency happened is not available. The tracing
   logic still runs when the ring buffer is disabled, but it should not
   be triggering notifications.

- Fix race on freeing the synthetic event "last_cmd" variable by adding
   a mutex around it.

- Fix race between reader and writer of the ring buffer by adding
   memory barriers. When the writer is still on the reader page it must
   have its content visible on the buffer before it moves the commit
   index that the reader uses to know how much content is on the page.

- Make get_lock_parent_ip() always inlined, as it uses _THIS_IP_ and
   _RET_IP_, which gets broken if it is not inlined.

- Make __field(int, arr[5]) in a TRACE_EVENT() macro fail to build.

   The field formats of trace events are calculated by using
   sizeof(type) and other means by what is passed into the structure
   macros like __field(). The __field() macro is only meant for atom
   types like int, long, short, pointer, etc. It is not meant for
   arrays.

   The code will currently compile with arrays, but then the format
   produced will be inaccurate, and user space parsing tools will break.

   Two bugs have already been fixed, now add code that will make the
   kernel fail to build if another trace event includes this buggy field
   format.

- Fix boot up snapshot code:

   Boot snapshots were triggering when not even asked for on the kernel
   command line. This was caused by two bugs:

    1) It would trigger a snapshot on any instance if one was created
       from the kernel command line.

    2) The error handling would only affect the top level instance.
       So the fact that a snapshot was done on a instance that didn't
       allocate a buffer triggered a warning written into the top level
       buffer, and worse yet, disabled the top level buffer.

- Fix memory leak that was caused when an error was logged in a trace
   buffer instance, and then the buffer instance was removed.

   The allocated error log messages still needed to be freed.

* tag 'trace-v6.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  tracing: Free error logs of tracing instances
  tracing: Fix ftrace_boot_snapshot command line logic
  tracing: Have tracing_snapshot_instance_cond() write errors to the appropriate instance
  tracing: Error if a trace event has an array for a __field()
  tracing/osnoise: Fix notify new tracing_max_latency
  tracing/timerlat: Notify new max thread latency
  ftrace: Mark get_lock_parent_ip() __always_inline
  ring-buffer: Fix race while reader and writer are on the same page
  tracing/synthetic: Fix races on freeing last_cmd

tracing: Free error logs of tracing instances

When a tracing instance is removed, the error messages that hold errors
that occurred in the instance needs to be freed. The following reports a
memory leak:

# cd /sys/kernel/tracing
# mkdir instances/foo
# echo 'hist:keys=x' > instances/foo/events/sched/sched_switch/trigger
# cat instances/foo/error_log
[  117.404795] hist:sched:sched_switch: error: Couldn't find field
   Command: hist:keys=x
                      ^
# rmdir instances/foo

Then check for memory leaks:

# echo scan > /sys/kernel/debug/kmemleak
# cat /sys/kernel/debug/kmemleak
unreferenced object 0xffff88810d8ec700 (size 192):
  comm "bash", pid 869, jiffies 4294950577 (age 215.752s)
  hex dump (first 32 bytes):
    60 dd 68 61 81 88 ff ff 60 dd 68 61 81 88 ff ff  `.ha....`.ha....
    a0 30 8c 83 ff ff ff ff 26 00 0a 00 00 00 00 00  .0......&.......
  backtrace:
    [<00000000dae26536>] kmalloc_trace+0x2a/0xa0
    [<00000000b2938940>] tracing_log_err+0x277/0x2e0
    [<000000004a0e1b07>] parse_atom+0x966/0xb40
    [<0000000023b24337>] parse_expr+0x5f3/0xdb0
    [<00000000594ad074>] event_hist_trigger_parse+0x27f8/0x3560
    [<00000000293a9645>] trigger_process_regex+0x135/0x1a0
    [<000000005c22b4f2>] event_trigger_write+0x87/0xf0
    [<000000002cadc509>] vfs_write+0x162/0x670
    [<0000000059c3b9be>] ksys_write+0xca/0x170
    [<00000000f1cddc00>] do_syscall_64+0x3e/0xc0
    [<00000000868ac68c>] entry_SYSCALL_64_after_hwframe+0x72/0xdc
unreferenced object 0xffff888170c35a00 (size 32):
  comm "bash", pid 869, jiffies 4294950577 (age 215.752s)
  hex dump (first 32 bytes):
    0a 20 20 43 6f 6d 6d 61 6e 64 3a 20 68 69 73 74  .  Command: hist
    3a 6b 65 79 73 3d 78 0a 00 00 00 00 00 00 00 00  :keys=x.........
  backtrace:
    [<000000006a747de5>] __kmalloc+0x4d/0x160
    [<000000000039df5f>] tracing_log_err+0x29b/0x2e0
    [<000000004a0e1b07>] parse_atom+0x966/0xb40
    [<0000000023b24337>] parse_expr+0x5f3/0xdb0
    [<00000000594ad074>] event_hist_trigger_parse+0x27f8/0x3560
    [<00000000293a9645>] trigger_process_regex+0x135/0x1a0
    [<000000005c22b4f2>] event_trigger_write+0x87/0xf0
    [<000000002cadc509>] vfs_write+0x162/0x670
    [<0000000059c3b9be>] ksys_write+0xca/0x170
    [<00000000f1cddc00>] do_syscall_64+0x3e/0xc0
    [<00000000868ac68c>] entry_SYSCALL_64_after_hwframe+0x72/0xdc

The problem is that the error log needs to be freed when the instance is
removed.

Link: https://lore.kernel.org/lkml/76134d9f-a5ba-6a0d-37b3-28310b4a1e91@alu.unizg.hr/
Link: https://lore.kernel.org/linux-trace-kernel/20230404194504.5790b95f@gandalf.local.home
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Eric Biggers <ebiggers@kernel.org>
Fixes: 2f754e771b1a6 ("tracing: Have the error logs show up in the proper instances")
Reported-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>

can: isotp: fix race between isotp_sendsmg() and isotp_release()

As discussed with Dae R. Jeong and Hillf Danton here [1] the sendmsg()
function in isotp.c might get into a race condition when restoring the
former tx.state from the old_state.

Remove the old_state concept and implement proper locking for the
ISOTP_IDLE transitions in isotp_sendmsg(), inspired by a
simplification idea from Hillf Danton.

Introduce a new tx.state ISOTP_SHUTDOWN and use the same locking
mechanism from isotp_release() which resolves a potential race between
isotp_sendsmg() and isotp_release().

[1] https://lore.kernel.org/linux-can/ZB%2F93xJxq%2FBUqAgG@dragonet

v1: https://lore.kernel.org/all/20230331102114.15164-1-socketcan@hartkopp.net
v2: https://lore.kernel.org/all/20230331123600.3550-1-socketcan@hartkopp.net
    take care of signal interrupts for wait_event_interruptible() in
    isotp_release()
v3: https://lore.kernel.org/all/20230331130654.9886-1-socketcan@hartkopp.net
    take care of signal interrupts for wait_event_interruptible() in
    isotp_sendmsg() in the wait_tx_done case
v4: https://lore.kernel.org/all/20230331131935.21465-1-socketcan@hartkopp.net
    take care of signal interrupts for wait_event_interruptible() in
    isotp_sendmsg() in ALL cases

Cc: Dae R. Jeong <threeearcat@gmail.com>
Cc: Hillf Danton <hdanton@sina.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Fixes: 4f027cba8216 ("can: isotp: split tx timer into transmission and timeout")
Link: https://lore.kernel.org/all/20230331131935.21465-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org
[mkl: rephrase commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Merge tag 'drm-intel-fixes-2023-04-05' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

drm/i915 fixes for v6.3-rc6:
- Fix DP MST DSC M/N calculation to use compressed bpp
- Fix racy use-after-free in perf ioctl
- Fix context runtime accounting
- Fix handling of GT reset during HuC loading
- Fix use of unsigned vm_fault_t for error values

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87zg7mzomz.fsf@intel.com

can: isotp: isotp_ops: fix poll() to not report false EPOLLOUT events

When using select()/poll()/epoll() with a non-blocking ISOTP socket to
wait for when non-blocking write is possible, a false EPOLLOUT event
is sometimes returned. This can happen at least after sending a
message which must be split to multiple CAN frames.

The reason is that isotp_sendmsg() returns -EAGAIN when tx.state is
not equal to ISOTP_IDLE and this behavior is not reflected in
datagram_poll(), which is used in isotp_ops.

This is fixed by introducing ISOTP-specific poll function, which
suppresses the EPOLLOUT events in that case.

v2: https://lore.kernel.org/all/20230302092812.320643-1-michal.sojka@cvut.cz
v1: https://lore.kernel.org/all/20230224010659.48420-1-michal.sojka@cvut.cz
https://lore.kernel.org/all/b53a04a2-ba1f-3858-84c1-d3eb3301ae15@hartkopp.net

Signed-off-by: Michal Sojka <michal.sojka@cvut.cz>
Reported-by: Jakub Jira <jirajak2@fel.cvut.cz>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Fixes: e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol")
Link: https://lore.kernel.org/all/20230331125511.372783-1-michal.sojka@cvut.cz
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

can: isotp: isotp_recvmsg(): use sock_recv_cmsgs() to get SOCK_RXQ_OVFL infos

isotp.c was still using sock_recv_timestamp() which does not provide
control messages to detect dropped PDUs in the receive path.

Fixes: e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol")
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230330170248.62342-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

can: j1939: j1939_tp_tx_dat_new(): fix out-of-bounds memory access

In the j1939_tp_tx_dat_new() function, an out-of-bounds memory access
could occur during the memcpy() operation if the size of skb->cb is
larger than the size of struct j1939_sk_buff_cb. This is because the
memcpy() operation uses the size of skb->cb, leading to a read beyond
the struct j1939_sk_buff_cb.

Updated the memcpy() operation to use the size of struct
j1939_sk_buff_cb instead of the size of skb->cb. This ensures that the
memcpy() operation only reads the memory within the bounds of struct
j1939_sk_buff_cb, preventing out-of-bounds memory access.

Additionally, add a BUILD_BUG_ON() to check that the size of skb->cb
is greater than or equal to the size of struct j1939_sk_buff_cb. This
ensures that the skb->cb buffer is large enough to hold the
j1939_sk_buff_cb structure.

Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Reported-by: Shuangpeng Bai <sjb7183@psu.edu>
Tested-by: Shuangpeng Bai <sjb7183@psu.edu>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://groups.google.com/g/syzkaller/c/G_LL-C3plRs/m/-8xCi6dCAgAJ
Link: https://lore.kernel.org/all/20230404073128.3173900-1-o.rempel@pengutronix.de
Cc: stable@vger.kernel.org
[mkl: rephrase commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

accel/ivpu: Fix S3 system suspend when not idle

Wait for VPU to be idle in ivpu_pm_suspend_cb() before powering off
the device, so jobs are not lost and TDRs are not triggered after
resume.

Fixes: 852be13f3bd3 ("accel/ivpu: Add PM support")
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230331113603.2802515-3-stanislaw.gruszka@linux.intel.com

accel/ivpu: Add dma fence to command buffers only

Currently job->done_fence is added to every BO handle within a job. If job
handle (command buffer) is shared between multiple submits, KMD will add
the fence in each of them. Then bo_wait_ioctl() executed on command buffer
will exit only when all jobs containing that handle are done.

This creates deadlock scenario for user mode driver in case when job handle
is added as dependency of another job, because bo_wait_ioctl() of first job
will wait until second job finishes, and second job can not finish before
first one.

Having fences added only to job buffer handle allows user space to execute
bo_wait_ioctl() on the job even if it's handle is submitted with other job.

Fixes: cd7272215c44 ("accel/ivpu: Add command buffer submission logic")
Signed-off-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230331113603.2802515-2-stanislaw.gruszka@linux.intel.com

tracing: Fix ftrace_boot_snapshot command line logic

The kernel command line ftrace_boot_snapshot by itself is supposed to
trigger a snapshot at the end of boot up of the main top level trace
buffer. A ftrace_boot_snapshot=foo will do the same for an instance called
foo that was created by trace_instance=foo,...

The logic was broken where if ftrace_boot_snapshot was by itself, it would
trigger a snapshot for all instances that had tracing enabled, regardless
if it asked for a snapshot or not.

When a snapshot is requested for a buffer, the buffer's
tr->allocated_snapshot is set to true. Use that to know if a trace buffer
wants a snapshot at boot up or not.

Since the top level buffer is part of the ftrace_trace_arrays list,
there's no reason to treat it differently than the other buffers. Just
iterate the list if ftrace_boot_snapshot was specified.

Link: https://lkml.kernel.org/r/20230405022341.895334039@goodmis.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ross Zwisler <zwisler@google.com>
Fixes: 9c1c251d670bc ("tracing: Allow boot instances to have snapshot buffers")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>

tracing: Have tracing_snapshot_instance_cond() write errors to the appropriate instance

If a trace instance has a failure with its snapshot code, the error
message is to be written to that instance's buffer. But currently, the
message is written to the top level buffer. Worse yet, it may also disable
the top level buffer and not the instance that had the issue.

Link: https://lkml.kernel.org/r/20230405022341.688730321@goodmis.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ross Zwisler <zwisler@google.com>
Fixes: 2824f50332486 ("tracing: Make the snapshot trigger work with instances")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>

gve: Secure enough bytes in the first TX desc for all TCP pkts

Non-GSO TCP packets whose SKBs' linear portion did not include the
entire TCP header were not populating the first Tx descriptor with
as many bytes as the vNIC expected. This change ensures that all
TCP packets populate the first descriptor with the correct number of
bytes.

Fixes: 893ce44df565 ("gve: Add basic driver framework for Compute Engine Virtual NIC")
Signed-off-by: Shailend Chand <shailend@google.com>
Link: https://lore.kernel.org/r/20230403172809.2939306-1-shailend@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

netlink: annotate lockless accesses to nlk->max_recvmsg_len

syzbot reported a data-race in data-race in netlink_recvmsg() [1]

Indeed, netlink_recvmsg() can be run concurrently,
and netlink_dump() also needs protection.

[1]
BUG: KCSAN: data-race in netlink_recvmsg / netlink_recvmsg

read to 0xffff888141840b38 of 8 bytes by task 23057 on cpu 0:
netlink_recvmsg+0xea/0x730 net/netlink/af_netlink.c:1988
sock_recvmsg_nosec net/socket.c:1017 [inline]
sock_recvmsg net/socket.c:1038 [inline]
__sys_recvfrom+0x1ee/0x2e0 net/socket.c:2194
__do_sys_recvfrom net/socket.c:2212 [inline]
__se_sys_recvfrom net/socket.c:2208 [inline]
__x64_sys_recvfrom+0x78/0x90 net/socket.c:2208
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

write to 0xffff888141840b38 of 8 bytes by task 23037 on cpu 1:
netlink_recvmsg+0x114/0x730 net/netlink/af_netlink.c:1989
sock_recvmsg_nosec net/socket.c:1017 [inline]
sock_recvmsg net/socket.c:1038 [inline]
____sys_recvmsg+0x156/0x310 net/socket.c:2720
___sys_recvmsg net/socket.c:2762 [inline]
do_recvmmsg+0x2e5/0x710 net/socket.c:2856
__sys_recvmmsg net/socket.c:2935 [inline]
__do_sys_recvmmsg net/socket.c:2958 [inline]
__se_sys_recvmmsg net/socket.c:2951 [inline]
__x64_sys_recvmmsg+0xe2/0x160 net/socket.c:2951
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

value changed: 0x0000000000000000 -> 0x0000000000001000

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 23037 Comm: syz-executor.2 Not tainted 6.3.0-rc4-syzkaller-00195-g5a57b48fdfcb #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/02/2023

Fixes: 9063e21fb026 ("netlink: autosize skb lengthes")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230403214643.768555-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ethtool: reset #lanes when lanes is omitted

If the number of lanes was forced and then subsequently the user
omits this parameter, the ksettings->lanes is reset. The driver
should then reset the number of lanes to the device's default
for the specified speed.

However, although the ksettings->lanes is set to 0, the mod variable
is not set to true to indicate the driver and userspace should be
notified of the changes.

The consequence is that the same ethtool operation will produce
different results based on the initial state.

If the initial state is:
$ ethtool swp1 | grep -A 3 'Speed: '
        Speed: 500000Mb/s
        Lanes: 2
        Duplex: Full
        Auto-negotiation: on

then executing 'ethtool -s swp1 speed 50000 autoneg off' will yield:
$ ethtool swp1 | grep -A 3 'Speed: '
        Speed: 500000Mb/s
        Lanes: 2
        Duplex: Full
        Auto-negotiation: off

While if the initial state is:
$ ethtool swp1 | grep -A 3 'Speed: '
        Speed: 500000Mb/s
        Lanes: 1
        Duplex: Full
        Auto-negotiation: off

executing the same 'ethtool -s swp1 speed 50000 autoneg off' results in:
$ ethtool swp1 | grep -A 3 'Speed: '
        Speed: 500000Mb/s
        Lanes: 1
        Duplex: Full
        Auto-negotiation: off

This patch fixes this behavior. Omitting lanes will always results in
the driver choosing the default lane width for the chosen speed. In this
scenario, regardless of the initial state, the end state will be, e.g.,

$ ethtool swp1 | grep -A 3 'Speed: '
        Speed: 500000Mb/s
        Lanes: 2
        Duplex: Full
        Auto-negotiation: off

Fixes: 012ce4dd3102 ("ethtool: Extend link modes settings uAPI with lanes")
Signed-off-by: Andy Roulin <aroulin@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/ac238d6b-8726-8156-3810-6471291dbc7f@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'raw-ping-fix-locking-in-proc-net-raw-icmp'

Kuniyuki Iwashima says:

====================
raw/ping: Fix locking in /proc/net/{raw,icmp}.

The first patch fixes a NULL deref for /proc/net/raw and second one fixes
the same issue for ping sockets.

The first patch also converts hlist_nulls to hlist, but this is because
the current code uses sk_nulls_for_each() for lockless readers, instead
of sk_nulls_for_each_rcu() which adds memory barrier, but raw sockets
does not use the nulls marker nor SLAB_TYPESAFE_BY_RCU in the first place.

OTOH, the ping sockets already uses sk_nulls_for_each_rcu(), and such
conversion can be posted later for net-next.
====================

Link: https://lore.kernel.org/r/20230403194959.48928-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ping: Fix potentail NULL deref for /proc/net/icmp.

After commit dbca1596bbb0 ("ping: convert to RCU lookups, get rid
of rwlock"), we use RCU for ping sockets, but we should use spinlock
for /proc/net/icmp to avoid a potential NULL deref mentioned in
the previous patch.

Let's go back to using spinlock there.

Note we can convert ping sockets to use hlist instead of hlist_nulls
because we do not use SLAB_TYPESAFE_BY_RCU for ping sockets.

Fixes: dbca1596bbb0 ("ping: convert to RCU lookups, get rid of rwlock")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

raw: Fix NULL deref in raw_get_next().

Dae R. Jeong reported a NULL deref in raw_get_next() [0].

It seems that the repro was running these sequences in parallel so
that one thread was iterating on a socket that was being freed in
another netns.

  unshare(0x40060200)
  r0 = syz_open_procfs(0x0, &(0x7f0000002080)='net/raw\x00')
  socket$inet_icmp_raw(0x2, 0x3, 0x1)
  pread64(r0, &(0x7f0000000000)=""/10, 0xa, 0x10000000007f)

After commit 0daf07e52709 ("raw: convert raw sockets to RCU"), we
use RCU and hlist_nulls_for_each_entry() to iterate over SOCK_RAW
sockets.  However, we should use spinlock for slow paths to avoid
the NULL deref.

Also, SOCK_RAW does not use SLAB_TYPESAFE_BY_RCU, and the slab object
is not reused during iteration in the grace period.  In fact, the
lockless readers do not check the nulls marker with get_nulls_value().
So, SOCK_RAW should use hlist instead of hlist_nulls.

Instead of adding an unnecessary barrier by sk_nulls_for_each_rcu(),
let's convert hlist_nulls to hlist and use sk_for_each_rcu() for
fast paths and sk_for_each() and spinlock for /proc/net/raw.

[0]:
general protection fault, probably for non-canonical address 0xdffffc0000000005: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f]
CPU: 2 PID: 20952 Comm: syz-executor.0 Not tainted 6.2.0-g048ec869bafd-dirty #7
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
RIP: 0010:read_pnet include/net/net_namespace.h:383 [inline]
RIP: 0010:sock_net include/net/sock.h:649 [inline]
RIP: 0010:raw_get_next net/ipv4/raw.c:974 [inline]
RIP: 0010:raw_get_idx net/ipv4/raw.c:986 [inline]
RIP: 0010:raw_seq_start+0x431/0x800 net/ipv4/raw.c:995
Code: ef e8 33 3d 94 f7 49 8b 6d 00 4c 89 ef e8 b7 65 5f f7 49 89 ed 49 83 c5 98 0f 84 9a 00 00 00 48 83 c5 c8 48 89 e8 48 c1 e8 03 <42> 80 3c 30 00 74 08 48 89 ef e8 00 3d 94 f7 4c 8b 7d 00 48 89 ef
RSP: 0018:ffffc9001154f9b0 EFLAGS: 00010206
RAX: 0000000000000005 RBX: 1ffff1100302c8fd RCX: 0000000000000000
RDX: 0000000000000028 RSI: ffffc9001154f988 RDI: ffffc9000f77a338
RBP: 0000000000000029 R08: ffffffff8a50ffb4 R09: fffffbfff24b6bd9
R10: fffffbfff24b6bd9 R11: 0000000000000000 R12: ffff88801db73b78
R13: fffffffffffffff9 R14: dffffc0000000000 R15: 0000000000000030
FS:  00007f843ae8e700(0000) GS:ffff888063700000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055bb9614b35f CR3: 000000003c672000 CR4: 00000000003506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
seq_read_iter+0x4c6/0x10f0 fs/seq_file.c:225
seq_read+0x224/0x320 fs/seq_file.c:162
pde_read fs/proc/inode.c:316 [inline]
proc_reg_read+0x23f/0x330 fs/proc/inode.c:328
vfs_read+0x31e/0xd30 fs/read_write.c:468
ksys_pread64 fs/read_write.c:665 [inline]
__do_sys_pread64 fs/read_write.c:675 [inline]
__se_sys_pread64 fs/read_write.c:672 [inline]
__x64_sys_pread64+0x1e9/0x280 fs/read_write.c:672
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x4e/0xa0 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x478d29
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f843ae8dbe8 EFLAGS: 00000246 ORIG_RAX: 0000000000000011
RAX: ffffffffffffffda RBX: 0000000000791408 RCX: 0000000000478d29
RDX: 000000000000000a RSI: 0000000020000000 RDI: 0000000000000003
RBP: 00000000f477909a R08: 0000000000000000 R09: 0000000000000000
R10: 000010000000007f R11: 0000000000000246 R12: 0000000000791740
R13: 0000000000791414 R14: 0000000000791408 R15: 00007ffc2eb48a50
</TASK>
Modules linked in:
---[ end trace 0000000000000000 ]---
RIP: 0010:read_pnet include/net/net_namespace.h:383 [inline]
RIP: 0010:sock_net include/net/sock.h:649 [inline]
RIP: 0010:raw_get_next net/ipv4/raw.c:974 [inline]
RIP: 0010:raw_get_idx net/ipv4/raw.c:986 [inline]
RIP: 0010:raw_seq_start+0x431/0x800 net/ipv4/raw.c:995
Code: ef e8 33 3d 94 f7 49 8b 6d 00 4c 89 ef e8 b7 65 5f f7 49 89 ed 49 83 c5 98 0f 84 9a 00 00 00 48 83 c5 c8 48 89 e8 48 c1 e8 03 <42> 80 3c 30 00 74 08 48 89 ef e8 00 3d 94 f7 4c 8b 7d 00 48 89 ef
RSP: 0018:ffffc9001154f9b0 EFLAGS: 00010206
RAX: 0000000000000005 RBX: 1ffff1100302c8fd RCX: 0000000000000000
RDX: 0000000000000028 RSI: ffffc9001154f988 RDI: ffffc9000f77a338
RBP: 0000000000000029 R08: ffffffff8a50ffb4 R09: fffffbfff24b6bd9
R10: fffffbfff24b6bd9 R11: 0000000000000000 R12: ffff88801db73b78
R13: fffffffffffffff9 R14: dffffc0000000000 R15: 0000000000000030
FS:  00007f843ae8e700(0000) GS:ffff888063700000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f92ff166000 CR3: 000000003c672000 CR4: 00000000003506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400

Fixes: 0daf07e52709 ("raw: convert raw sockets to RCU")
Reported-by: syzbot <syzkaller@googlegroups.com>
Reported-by: Dae R. Jeong <threeearcat@gmail.com>
Link: https://lore.kernel.org/netdev/ZCA2mGV_cmq7lIfV@dragonet/
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'for-linus' of git://git./virt/kvm/kvm

Pull kvm fixes from Paolo Bonzini:
"PPC:
   - Hide KVM_CAP_IRQFD_RESAMPLE if XIVE is enabled

  s390:
   - Fix handling of external interrupts in protected guests

  x86:
   - Resample the pending state of IOAPIC interrupts when unmasking them

   - Fix usage of Hyper-V "enlightened TLB" on AMD

   - Small fixes to real mode exceptions

   - Suppress pending MMIO write exits if emulator detects exception

  Documentation:
   - Fix rST syntax"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  docs: kvm: x86: Fix broken field list
  KVM: PPC: Make KVM_CAP_IRQFD_RESAMPLE platform dependent
  KVM: s390: pv: fix external interruption loop not always detected
  KVM: nVMX: Do not report error code when synthesizing VM-Exit from Real Mode
  KVM: x86: Clear "has_error_code", not "error_code", for RM exception injection
  KVM: x86: Suppress pending MMIO write exits if emulator detects exception
  KVM: x86/ioapic: Resample the pending state of an IRQ when unmasking
  KVM: irqfd: Make resampler_list an RCU list
  KVM: SVM: Flush Hyper-V TLB when required

Merge tag 'nfsd-6.3-5' of git://git./linux/kernel/git/cel/linux

Pull nfsd fixes from Chuck Lever:

- Fix a crash and a resource leak in NFSv4 COMPOUND processing

- Fix issues with AUTH_SYS credential handling

- Try again to address an NFS/NFSD/SUNRPC build dependency regression

* tag 'nfsd-6.3-5' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
  NFSD: callback request does not use correct credential for AUTH_SYS
  NFS: Remove "select RPCSEC_GSS_KRB5
  sunrpc: only free unix grouplist after RCU settles
  nfsd: call op_release, even when op_func returns an error
  NFSD: Avoid calling OPDESC() with ops->opnum == OP_ILLEGAL

docs: kvm: x86: Fix broken field list

Add a missing ":" to fix a broken field list.

Signed-off-by: Takahiro Itazuri <itazur@amazon.com>
Fixes: ba7bb663f554 ("KVM: x86: Provide per VM capability for disabling PMU virtualization")
Message-Id: <20230331093116.99820-1-itazur@amazon.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

asm-generic: avoid __generic_cmpxchg_local warnings

Code that passes a 32-bit constant into cmpxchg() produces a harmless
sparse warning because of the truncation in the branch that is not taken:

fs/erofs/zdata.c: note: in included file (through /home/arnd/arm-soc/arch/arm/include/asm/cmpxchg.h, /home/arnd/arm-soc/arch/arm/include/asm/atomic.h, /home/arnd/arm-soc/include/linux/atomic.h, ...):
include/asm-generic/cmpxchg-local.h:29:33: warning: cast truncates bits from constant value (5f0ecafe becomes fe)
include/asm-generic/cmpxchg-local.h:33:34: warning: cast truncates bits from constant value (5f0ecafe becomes cafe)
include/asm-generic/cmpxchg-local.h:29:33: warning: cast truncates bits from constant value (5f0ecafe becomes fe)
include/asm-generic/cmpxchg-local.h:30:42: warning: cast truncates bits from constant value (5f0edead becomes ad)
include/asm-generic/cmpxchg-local.h:33:34: warning: cast truncates bits from constant value (5f0ecafe becomes cafe)
include/asm-generic/cmpxchg-local.h:34:44: warning: cast truncates bits from constant value (5f0edead becomes dead)

This was reported as a regression to Matt's recent __generic_cmpxchg_local
patch, though this patch only added more warnings on top of the ones
that were already there.

Rewording the truncation to use an explicit bitmask instead of a cast
to a smaller type avoids the warning but otherwise leaves the code
unchanged.

I had another look at why the cast is even needed for atomic_cmpxchg(),
and as Matt describes the problem here is that atomic_t contains a
signed 'int', but cmpxchg() takes an 'unsigned long' argument, and
converting between the two leads to a 64-bit sign-extension of
negative 32-bit atomics.

I checked the other implementations of arch_cmpxchg() and did not find
any others that run into the same problem as __generic_cmpxchg_local(),
but it's easy to be on the safe side here and always convert the
signed int into an unsigned int when calling arch_cmpxchg(), as this
will work even when any of the arch_cmpxchg() implementations run
into the same problem.

Fixes: 624654152284 ("locking/atomic: cmpxchg: Make __generic_cmpxchg_local compare against zero-extended 'old' value")
Reviewed-by: Matt Evans <mev@rivosinc.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

asm-generic/io.h: suppress endianness warnings for relaxed accessors

Copy the forced type casts from the normal MMIO accessors to suppress
the sparse warnings that point out __raw_readl() returns a native endian
word (just like readl()).

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

asm-generic/io.h: suppress endianness warnings for readq() and writeq()

Commit c1d55d50139b ("asm-generic/io.h: Fix sparse warnings on
big-endian architectures") missed fixing the 64-bit accessors.

Arnd explains in the attached link why the casts are necessary, even if
__raw_readq() and __raw_writeq() do not take endian-specific types.

Link: https://lore.kernel.org/lkml/9105d6fc-880b-4734-857d-e3d30b87ccf6@app.fastmail.com/
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

ice: Reset FDIR counter in FDIR init stage

Reset the FDIR counters when FDIR inits. Without this patch,
when VF initializes or resets, all the FDIR counters are not
cleaned, which may cause unexpected behaviors for future FDIR
rule create (e.g., rule conflict).

Fixes: 1f7ea1cd6a37 ("ice: Enable FDIR Configure for AVF")
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Signed-off-by: Lingyu Liu <lingyu.liu@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice: fix wrong fallback logic for FDIR

When adding a FDIR filter, if ice_vc_fdir_set_irq_ctx returns failure,
the inserted fdir entry will not be removed and if ice_vc_fdir_write_fltr
returns failure, the fdir context info for irq handler will not be cleared
which may lead to inconsistent or memory leak issue. This patch refines
failure cases to resolve this issue.

Fixes: 1f7ea1cd6a37 ("ice: Enable FDIR Configure for AVF")
Signed-off-by: Simei Su <simei.su@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

NFSD: callback request does not use correct credential for AUTH_SYS

Currently callback request does not use the credential specified in
CREATE_SESSION if the security flavor for the back channel is AUTH_SYS.

Problem was discovered by pynfs 4.1 DELEG5 and DELEG7 test with error:
DELEG5 st_delegation.testCBSecParms : FAILURE
expected callback with uid, gid == 17, 19, got 0, 0

Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Fixes: 8276c902bbe9 ("SUNRPC: remove uid and gid from struct auth_cred")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>

NFS: Remove "select RPCSEC_GSS_KRB5

If CONFIG_CRYPTO=n (e.g. arm/shmobile_defconfig):

   WARNING: unmet direct dependencies detected for RPCSEC_GSS_KRB5
     Depends on [n]: NETWORK_FILESYSTEMS [=y] && SUNRPC [=y] && CRYPTO [=n]
     Selected by [y]:
     - NFS_V4 [=y] && NETWORK_FILESYSTEMS [=y] && NFS_FS [=y]

As NFSv4 can work without crypto enabled, remove the RPCSEC_GSS_KRB5
dependency altogether.

Trond says:
> It is possible to use the NFSv4.1 client with just AUTH_SYS, and
> in fact there are plenty of people out there using only that. The
> fact that RFC5661 gets its knickers in a twist about RPCSEC_GSS
> support is largely irrelevant to those people.
>
> The other issue is that ’select’ enforces the strict dependency
> that if the NFS client is compiled into the kernel, then the
> RPCSEC_GSS and kerberos code needs to be compiled in as well: they
> cannot exist as modules.

Fixes: e57d06527738 ("NFS & NFSD: Update GSS dependencies")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Suggested-by: Trond Myklebust <trondmy@hammerspace.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>

sunrpc: only free unix grouplist after RCU settles

While the unix_gid object is rcu-freed, the group_info list that it
contains is not. Ensure that we only put the group list reference once
we are really freeing the unix_gid object.

Reported-by: Zhi Li <yieli@redhat.com>
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2183056
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Fixes: fd5d2f78261b ("SUNRPC: Make server side AUTH_UNIX use lockless lookups")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>

net: stmmac: fix up RX flow hash indirection table when setting channels

stmmac_reinit_queues() fails to fix up the RX hash.  Even if the number
of channels gets restricted, the output of `ethtool -x' indicates that
all RX queues are used:

  $ ethtool -l enp0s29f2
  Channel parameters for enp0s29f2:
  Pre-set maximums:
  RX: 8
  TX: 8
  Other: n/a
  Combined: n/a
  Current hardware settings:
  RX: 8
  TX: 8
  Other: n/a
  Combined: n/a
  $ ethtool -x enp0s29f2
  RX flow hash indirection table for enp0s29f2 with 8 RX ring(s):
      0:      0     1     2     3     4     5     6     7
      8:      0     1     2     3     4     5     6     7
  [...]
  $ ethtool -L enp0s29f2 rx 3
  $ ethtool -x enp0s29f2
  RX flow hash indirection table for enp0s29f2 with 3 RX ring(s):
      0:      0     1     2     3     4     5     6     7
      8:      0     1     2     3     4     5     6     7
  [...]

Fix this by setting the indirection table according to the number
of specified queues.  The result is now as expected:

  $ ethtool -L enp0s29f2 rx 3
  $ ethtool -x enp0s29f2
  RX flow hash indirection table for enp0s29f2 with 3 RX ring(s):
      0:      0     1     2     0     1     2     0     1
      8:      2     0     1     2     0     1     2     0
  [...]

Tested on Intel Elkhart Lake.

Fixes: 0366f7e06a6b ("net: stmmac: add ethtool support for get/set channels")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Link: https://lore.kernel.org/r/20230403121120.489138-1-vinschen@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

iommufd: Do not corrupt the pfn list when doing batch carry

If batch->end is 0 then setting npfns[0] before computing the new value of
pfns will fail to adjust the pfn and result in various page accounting
corruptions. It should be ordered after.

This seems to result in various kinds of page meta-data corruption related
failures:

  WARNING: CPU: 1 PID: 527 at mm/gup.c:75 try_grab_folio+0x503/0x740
  Modules linked in:
  CPU: 1 PID: 527 Comm: repro Not tainted 6.3.0-rc2-eeac8ede1755+ #1
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
  RIP: 0010:try_grab_folio+0x503/0x740
  Code: e3 01 48 89 de e8 6d c1 dd ff 48 85 db 0f 84 7c fe ff ff e8 4f bf dd ff 49 8d 47 ff 48 89 45 d0 e9 73 fe ff ff e8 3d bf dd ff <0f> 0b 31 db e9 d0 fc ff ff e8 2f bf dd ff 48 8b 5d c8 31 ff 48 89
  RSP: 0018:ffffc90000f37908 EFLAGS: 00010046
  RAX: 0000000000000000 RBX: 00000000fffffc02 RCX: ffffffff81504c26
  RDX: 0000000000000000 RSI: ffff88800d030000 RDI: 0000000000000002
  RBP: ffffc90000f37948 R08: 000000000003ca24 R09: 0000000000000008
  R10: 000000000003ca00 R11: 0000000000000023 R12: ffffea000035d540
  R13: 0000000000000001 R14: 0000000000000000 R15: ffffea000035d540
  FS:  00007fecbf659740(0000) GS:ffff88807dd00000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00000000200011c3 CR3: 000000000ef66006 CR4: 0000000000770ee0
  PKRU: 55555554
  Call Trace:
   <TASK>
   internal_get_user_pages_fast+0xd32/0x2200
   pin_user_pages_fast+0x65/0x90
   pfn_reader_user_pin+0x376/0x390
   pfn_reader_next+0x14a/0x7b0
   pfn_reader_first+0x140/0x1b0
   iopt_area_fill_domain+0x74/0x210
   iopt_table_add_domain+0x30e/0x6e0
   iommufd_device_selftest_attach+0x7f/0x140
   iommufd_test+0x10ff/0x16f0
   iommufd_fops_ioctl+0x206/0x330
   __x64_sys_ioctl+0x10e/0x160
   do_syscall_64+0x3b/0x90
   entry_SYSCALL_64_after_hwframe+0x72/0xdc

Cc: <stable@vger.kernel.org>
Fixes: f394576eb11d ("iommufd: PFN handling for iopt_pages")
Link: https://lore.kernel.org/r/3-v1-ceab6a4d7d7a+94-iommufd_syz_jgg@nvidia.com
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>

iommufd: Fix unpinning of pages when an access is present

syzkaller found that the calculation of batch_last_index should use
'start_index' since at input to this function the batch is either empty or
it has already been adjusted to cross any accesses so it will start at the
point we are unmapping from.

Getting this wrong causes the unmap to run over the end of the pages
which corrupts pages that were never mapped. In most cases this triggers
the num pinned debugging:

  WARNING: CPU: 0 PID: 557 at drivers/iommu/iommufd/pages.c:294 __iopt_area_unfill_domain+0x152/0x560
  Modules linked in:
  CPU: 0 PID: 557 Comm: repro Not tainted 6.3.0-rc2-eeac8ede1755 #1
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
  RIP: 0010:__iopt_area_unfill_domain+0x152/0x560
  Code: d2 0f ff 44 8b 64 24 54 48 8b 44 24 48 31 ff 44 89 e6 48 89 44 24 38 e8 fc d3 0f ff 45 85 e4 0f 85 eb 01 00 00 e8 0e d2 0f ff <0f> 0b e8 07 d2 0f ff 48 8b 44 24 38 89 5c 24 58 89 18 8b 44 24 54
  RSP: 0018:ffffc9000108baf0 EFLAGS: 00010246
  RAX: 0000000000000000 RBX: 00000000ffffffff RCX: ffffffff821e3f85
  RDX: 0000000000000000 RSI: ffff88800faf0000 RDI: 0000000000000002
  RBP: ffffc9000108bd18 R08: 000000000003ca25 R09: 0000000000000014
  R10: 000000000003ca00 R11: 0000000000000024 R12: 0000000000000004
  R13: 0000000000000801 R14: 00000000000007ff R15: 0000000000000800
  FS:  00007f3499ce1740(0000) GS:ffff88807dc00000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000000020000243 CR3: 00000000179c2001 CR4: 0000000000770ef0
  PKRU: 55555554
  Call Trace:
   <TASK>
   iopt_area_unfill_domain+0x32/0x40
   iopt_table_remove_domain+0x23f/0x4c0
   iommufd_device_selftest_detach+0x3a/0x90
   iommufd_selftest_destroy+0x55/0x70
   iommufd_object_destroy_user+0xce/0x130
   iommufd_destroy+0xa2/0xc0
   iommufd_fops_ioctl+0x206/0x330
   __x64_sys_ioctl+0x10e/0x160
   do_syscall_64+0x3b/0x90
   entry_SYSCALL_64_after_hwframe+0x72/0xdc

Also add some useful WARN_ON sanity checks.

Cc: <stable@vger.kernel.org>
Fixes: 8d160cd4d506 ("iommufd: Algorithms for PFN storage")
Link: https://lore.kernel.org/r/2-v1-ceab6a4d7d7a+94-iommufd_syz_jgg@nvidia.com
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>

iommufd: Check for uptr overflow

syzkaller found that setting up a map with a user VA that wraps past zero
can trigger WARN_ONs, particularly from pin_user_pages weirdly returning 0
due to invalid arguments.

Prevent creating a pages with a uptr and size that would math overflow.

  WARNING: CPU: 0 PID: 518 at drivers/iommu/iommufd/pages.c:793 pfn_reader_user_pin+0x2e6/0x390
  Modules linked in:
  CPU: 0 PID: 518 Comm: repro Not tainted 6.3.0-rc2-eeac8ede1755+ #1
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
  RIP: 0010:pfn_reader_user_pin+0x2e6/0x390
  Code: b1 11 e9 25 fe ff ff e8 28 e4 0f ff 31 ff 48 89 de e8 2e e6 0f ff 48 85 db 74 0a e8 14 e4 0f ff e9 4d ff ff ff e8 0a e4 0f ff <0f> 0b bb f2 ff ff ff e9 3c ff ff ff e8 f9 e3 0f ff ba 01 00 00 00
  RSP: 0018:ffffc90000f9fa30 EFLAGS: 00010246
  RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffff821e2b72
  RDX: 0000000000000000 RSI: ffff888014184680 RDI: 0000000000000002
  RBP: ffffc90000f9fa78 R08: 00000000000000ff R09: 0000000079de6f4e
  R10: ffffc90000f9f790 R11: ffff888014185418 R12: ffffc90000f9fc60
  R13: 0000000000000002 R14: ffff888007879800 R15: 0000000000000000
  FS:  00007f4227555740(0000) GS:ffff88807dc00000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000000020000043 CR3: 000000000e748005 CR4: 0000000000770ef0
  PKRU: 55555554
  Call Trace:
   <TASK>
   pfn_reader_next+0x14a/0x7b0
   ? interval_tree_double_span_iter_update+0x11a/0x140
   pfn_reader_first+0x140/0x1b0
   iopt_pages_rw_slow+0x71/0x280
   ? __this_cpu_preempt_check+0x20/0x30
   iopt_pages_rw_access+0x2b2/0x5b0
   iommufd_access_rw+0x19f/0x2f0
   iommufd_test+0xd11/0x16f0
   ? write_comp_data+0x2f/0x90
   iommufd_fops_ioctl+0x206/0x330
   __x64_sys_ioctl+0x10e/0x160
   ? __pfx_iommufd_fops_ioctl+0x10/0x10
   do_syscall_64+0x3b/0x90
   entry_SYSCALL_64_after_hwframe+0x72/0xdc

Cc: <stable@vger.kernel.org>
Fixes: 8d160cd4d506 ("iommufd: Algorithms for PFN storage")
Link: https://lore.kernel.org/r/1-v1-ceab6a4d7d7a+94-iommufd_syz_jgg@nvidia.com
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>

net: ethernet: ti: am65-cpsw: Fix mdio cleanup in probe

In the am65_cpsw_nuss_probe() function's cleanup path, the call to
of_platform_device_destroy() for the common->mdio_dev device is invoked
unconditionally. It is possible that either the MDIO node is not present
in the device-tree, or the MDIO node is disabled in the device-tree. In
both these cases, the MDIO device is not created, resulting in a NULL
pointer dereference when the of_platform_device_destroy() function is
invoked on the common->mdio_dev device on the cleanup path.

Fix this by ensuring that the common->mdio_dev device exists, before
attempting to invoke of_platform_device_destroy().

Fixes: a45cfcc69a25 ("net: ethernet: ti: am65-cpsw-nuss: use of_platform_device_create() for mdio")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230403090321.835877-1-s-vadapalli@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Merge tag 'vfs.misc.fixes.v6.3-rc6' of git://git./linux/kernel/git/vfs/idmapping

Pull vfs fix from Christian Brauner:
"When a mount or mount tree is made shared the vfs allocates new peer
  group ids for all mounts that have no peer group id set. Only mounts
  that aren't marked with MNT_SHARED are relevant here as MNT_SHARED
  indicates that the mount has fully transitioned to a shared mount. The
  peer group id handling is done with namespace lock held.

  On failure, the peer group id settings of mounts for which a new peer
  group id was allocated need to be reverted and the allocated peer
  group id freed. The cleanup_group_ids() helper can identify the mounts
  to cleanup by checking whether a given mount has a peer group id set
  but isn't marked MNT_SHARED. The deallocation always needs to happen
  with namespace lock held to protect against concurrent modifications
  of the propagation settings.

  This fixes the one place where the namespace lock was dropped before
  calling cleanup_group_ids()"

* tag 'vfs.misc.fixes.v6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/idmapping:
  fs: drop peer group ids under namespace lock

Merge tag 'hyperv-fixes-signed-20230402' of git://git./linux/kernel/git/hyperv/linux

Pull hyperv fixes from Wei Liu:

- Fix a bug in channel allocation for VMbus (Mohammed Gamal)

- Do not allow root partition functionality in CVM (Michael Kelley)

* tag 'hyperv-fixes-signed-20230402' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
x86/hyperv: Block root partition functionality in a Confidential VM
Drivers: vmbus: Check for channel allocation before looking up relids

tracing: Error if a trace event has an array for a __field()

A __field() in the TRACE_EVENT() macro is used to set up the fields of the
trace event data. It is for single storage units (word, char, int,
pointer, etc) and not for complex structures or arrays. Unfortunately,
there's nothing preventing the build from accepting:

__field(int, arr[5]);

from building. It will turn into a array value. This use to work fine, as
the offset and size use to be determined by the macro using the field name,
but things have changed and the offset and size are now determined by the
type. So the above would only be size 4, and the next field will be
located 4 bytes from it (instead of 20).

The proper way to declare static arrays is to use the __array() macro.

Instead of __field(int, arr[5]) it should be __array(int, arr, 5).

Add some macro tricks to the building of a trace event from the
TRACE_EVENT() macro such that __field(int, arr[5]) will fail to build. A
comment by the failure will explain why the build failed.

Link: https://lore.kernel.org/lkml/20230306122549.236561-1-douglas.raillard@arm.com/
Link: https://lore.kernel.org/linux-trace-kernel/20230309221302.642e82d9@gandalf.local.home
Reported-by: Douglas RAILLARD <douglas.raillard@arm.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>

tracing/osnoise: Fix notify new tracing_max_latency

osnoise/timerlat tracers are reporting new max latency on instances
where the tracing is off, creating inconsistencies between the max
reported values in the trace and in the tracing_max_latency. Thus
only report new tracing_max_latency on active tracing instances.

Link: https://lkml.kernel.org/r/ecd109fde4a0c24ab0f00ba1e9a144ac19a91322.1680104184.git.bristot@kernel.org
Cc: stable@vger.kernel.org
Fixes: dae181349f1e ("tracing/osnoise: Support a list of trace_array *tr")
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>

tracing/timerlat: Notify new max thread latency

timerlat is not reporting a new tracing_max_latency for the thread
latency. The reason is that it is not calling notify_new_max_latency()
function after the new thread latency is sampled.

Call notify_new_max_latency() after computing the thread latency.

Link: https://lkml.kernel.org/r/16e18d61d69073d0192ace07bf61e405cca96e9c.1680104184.git.bristot@kernel.org
Cc: stable@vger.kernel.org
Fixes: dae181349f1e ("tracing/osnoise: Support a list of trace_array *tr")
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>

ftrace: Mark get_lock_parent_ip() __always_inline

If the compiler decides not to inline this function then preemption
tracing will always show an IP inside the preemption disabling path and
never the function actually calling preempt_{enable,disable}.

Link: https://lore.kernel.org/linux-trace-kernel/20230327173647.1690849-1-john@metanate.com
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: stable@vger.kernel.org
Fixes: f904f58263e1d ("sched/debug: Fix preempt_disable_ip recording for preempt_disable()")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>

ring-buffer: Fix race while reader and writer are on the same page

When user reads file 'trace_pipe', kernel keeps printing following logs
that warn at "cpu_buffer->reader_page->read > rb_page_size(reader)" in
rb_get_reader_page(). It just looks like there's an infinite loop in
tracing_read_pipe(). This problem occurs several times on arm64 platform
when testing v5.10 and below.

  Call trace:
   rb_get_reader_page+0x248/0x1300
   rb_buffer_peek+0x34/0x160
   ring_buffer_peek+0xbc/0x224
   peek_next_entry+0x98/0xbc
   __find_next_entry+0xc4/0x1c0
   trace_find_next_entry_inc+0x30/0x94
   tracing_read_pipe+0x198/0x304
   vfs_read+0xb4/0x1e0
   ksys_read+0x74/0x100
   __arm64_sys_read+0x24/0x30
   el0_svc_common.constprop.0+0x7c/0x1bc
   do_el0_svc+0x2c/0x94
   el0_svc+0x20/0x30
   el0_sync_handler+0xb0/0xb4
   el0_sync+0x160/0x180

Then I dump the vmcore and look into the problematic per_cpu ring_buffer,
I found that tail_page/commit_page/reader_page are on the same page while
reader_page->read is obviously abnormal:
  tail_page == commit_page == reader_page == {
    .write = 0x100d20,
    .read = 0x8f9f4805,  // Far greater than 0xd20, obviously abnormal!!!
    .entries = 0x10004c,
    .real_end = 0x0,
    .page = {
      .time_stamp = 0x857257416af0,
      .commit = 0xd20,  // This page hasn't been full filled.
      // .data[0...0xd20] seems normal.
    }
}

The root cause is most likely the race that reader and writer are on the
same page while reader saw an event that not fully committed by writer.

To fix this, add memory barriers to make sure the reader can see the
content of what is committed. Since commit a0fcaaed0c46 ("ring-buffer: Fix
race between reset page and reading page") has added the read barrier in
rb_get_reader_page(), here we just need to add the write barrier.

Link: https://lore.kernel.org/linux-trace-kernel/20230325021247.2923907-1-zhengyejian1@huawei.com
Cc: stable@vger.kernel.org
Fixes: 77ae365eca89 ("ring-buffer: make lockless")
Suggested-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Zheng Yejian <zhengyejian1@huawei.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>

tracing/synthetic: Fix races on freeing last_cmd

Currently, the "last_cmd" variable can be accessed by multiple processes
asynchronously when multiple users manipulate synthetic_events node
at the same time, it could lead to use-after-free or double-free.

This patch add "lastcmd_mutex" to prevent "last_cmd" from being accessed
asynchronously.

================================================================

It's easy to reproduce in the KASAN environment by running the two
scripts below in different shells.

script 1:
        while :
        do
                echo -n -e '\x88' > /sys/kernel/tracing/synthetic_events
        done

script 2:
        while :
        do
                echo -n -e '\xb0' > /sys/kernel/tracing/synthetic_events
        done

================================================================
double-free scenario:

    process A                       process B
-------------------               ---------------
1.kstrdup last_cmd
                                  2.free last_cmd
3.free last_cmd(double-free)

================================================================
use-after-free scenario:

    process A                       process B
-------------------               ---------------
1.kstrdup last_cmd
                                  2.free last_cmd
3.tracing_log_err(use-after-free)

================================================================

Appendix 1. KASAN report double-free:

BUG: KASAN: double-free in kfree+0xdc/0x1d4
Free of addr ***** by task sh/4879
Call trace:
        ...
        kfree+0xdc/0x1d4
        create_or_delete_synth_event+0x60/0x1e8
        trace_parse_run_command+0x2bc/0x4b8
        synth_events_write+0x20/0x30
        vfs_write+0x200/0x830
        ...

Allocated by task 4879:
        ...
        kstrdup+0x5c/0x98
        create_or_delete_synth_event+0x6c/0x1e8
        trace_parse_run_command+0x2bc/0x4b8
        synth_events_write+0x20/0x30
        vfs_write+0x200/0x830
        ...

Freed by task 5464:
        ...
        kfree+0xdc/0x1d4
        create_or_delete_synth_event+0x60/0x1e8
        trace_parse_run_command+0x2bc/0x4b8
        synth_events_write+0x20/0x30
        vfs_write+0x200/0x830
        ...

================================================================
Appendix 2. KASAN report use-after-free:

BUG: KASAN: use-after-free in strlen+0x5c/0x7c
Read of size 1 at addr ***** by task sh/5483
sh: CPU: 7 PID: 5483 Comm: sh
        ...
        __asan_report_load1_noabort+0x34/0x44
        strlen+0x5c/0x7c
        tracing_log_err+0x60/0x444
        create_or_delete_synth_event+0xc4/0x204
        trace_parse_run_command+0x2bc/0x4b8
        synth_events_write+0x20/0x30
        vfs_write+0x200/0x830
        ...

Allocated by task 5483:
        ...
        kstrdup+0x5c/0x98
        create_or_delete_synth_event+0x80/0x204
        trace_parse_run_command+0x2bc/0x4b8
        synth_events_write+0x20/0x30
        vfs_write+0x200/0x830
        ...

Freed by task 5480:
        ...
        kfree+0xdc/0x1d4
        create_or_delete_synth_event+0x74/0x204
        trace_parse_run_command+0x2bc/0x4b8
        synth_events_write+0x20/0x30
        vfs_write+0x200/0x830
        ...

Link: https://lore.kernel.org/linux-trace-kernel/20230321110444.1587-1-Tze-nan.Wu@mediatek.com
Fixes: 27c888da9867 ("tracing: Remove size restriction on synthetic event cmd error logging")
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: "Tom Zanussi" <zanussi@kernel.org>
Signed-off-by: Tze-nan Wu <Tze-nan.Wu@mediatek.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>

bpf, arm64: Fixed a BTI error on returning to patched function

When BPF_TRAMP_F_CALL_ORIG is set, BPF trampoline uses BLR to jump
back to the instruction next to call site to call the patched function.
For BTI-enabled kernel, the instruction next to call site is usually
PACIASP, in this case, it's safe to jump back with BLR. But when
the call site is not followed by a PACIASP or bti, a BTI exception
is triggered.

Here is a fault log:

Unhandled 64-bit el1h sync exception on CPU0, ESR 0x0000000034000002 -- BTI
CPU: 0 PID: 263 Comm: test_progs Tainted: GF
Hardware name: linux,dummy-virt (DT)
pstate: 40400805 (nZcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=-c)
pc : bpf_fentry_test1+0xc/0x30
lr : bpf_trampoline_6442573892_0+0x48/0x1000
sp : ffff80000c0c3a50
x29: ffff80000c0c3a90 x28: ffff0000c2e6c080 x27: 0000000000000000
x26: 0000000000000000 x25: 0000000000000000 x24: 0000000000000050
x23: 0000000000000000 x22: 0000ffffcfd2a7f0 x21: 000000000000000a
x20: 0000ffffcfd2a7f0 x19: 0000000000000000 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 0000ffffcfd2a7f0
x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
x11: 0000000000000000 x10: ffff80000914f5e4 x9 : ffff8000082a1528
x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0101010101010101
x5 : 0000000000000000 x4 : 00000000fffffff2 x3 : 0000000000000001
x2 : ffff8001f4b82000 x1 : 0000000000000000 x0 : 0000000000000001
Kernel panic - not syncing: Unhandled exception
CPU: 0 PID: 263 Comm: test_progs Tainted: GF
Hardware name: linux,dummy-virt (DT)
Call trace:
  dump_backtrace+0xec/0x144
  show_stack+0x24/0x7c
  dump_stack_lvl+0x8c/0xb8
  dump_stack+0x18/0x34
  panic+0x1cc/0x3ec
  __el0_error_handler_common+0x0/0x130
  el1h_64_sync_handler+0x60/0xd0
  el1h_64_sync+0x78/0x7c
  bpf_fentry_test1+0xc/0x30
  bpf_fentry_test1+0xc/0x30
  bpf_prog_test_run_tracing+0xdc/0x2a0
  __sys_bpf+0x438/0x22a0
  __arm64_sys_bpf+0x30/0x54
  invoke_syscall+0x78/0x110
  el0_svc_common.constprop.0+0x6c/0x1d0
  do_el0_svc+0x38/0xe0
  el0_svc+0x30/0xd0
  el0t_64_sync_handler+0x1ac/0x1b0
  el0t_64_sync+0x1a0/0x1a4
Kernel Offset: disabled
CPU features: 0x0000,00034c24,f994fdab
Memory Limit: none

And the instruction next to call site of bpf_fentry_test1 is ADD,
not PACIASP:

<bpf_fentry_test1>:
bti     c
nop
nop
add     w0, w0, #0x1
paciasp

For BPF prog, JIT always puts a PACIASP after call site for BTI-enabled
kernel, so there is no problem. To fix it, replace BLR with RET to bypass
the branch target check.

Fixes: efc9909fdce0 ("bpf, arm64: Add bpf trampoline for arm64")
Reported-by: Florent Revest <revest@chromium.org>
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Florent Revest <revest@chromium.org>
Acked-by: Florent Revest <revest@chromium.org>
Link: https://lore.kernel.org/bpf/20230401234144.3719742-1-xukuohai@huaweicloud.com

wifi: mt76: ignore key disable commands

This helps avoid cleartext leakage of already queued or powersave buffered
packets, when a reassoc triggers the key deletion.

Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230330091259.61378-1-nbd@nbd.name

wifi: ath11k: reduce the MHI timeout to 20s

Currently ath11k breaks after hibernation, the reason being that ath11k expects
that the wireless device will have power during suspend and the firmware will
continue running. But of course during hibernation the power from the device is
cut off and firmware is not running when resuming, so ath11k will fail.

(The reason why ath11k needs the firmware running is the interaction between
mac80211 and MHI stack, it's a long story and more info in the bugzilla report.)

In SUSE kernels the watchdog timeout is reduced from the default 120 to 60 seconds:

CONFIG_DPM_WATCHDOG_TIMEOUT=60

But as the ath11k MHI timeout is 90 seconds the kernel will crash before will
ath11k will recover in resume callback. To avoid the crash reduce the MHI
timeout to just 20 seconds.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.9

Link: https://bugzilla.kernel.org/show_bug.cgi?id=214649
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230329162038.8637-1-kvalo@kernel.org

platform/x86: thinkpad_acpi: Add missing T14s Gen1 type to s2idle quirk list

From the commit message adding the first s2idle quirks:

> Lenovo laptops that contain NVME SSDs across a variety of generations have
> trouble resuming from suspend to idle when the IOMMU translation layer is
> active for the NVME storage device.
>
> This generally manifests as a large resume delay or page faults. These
> delays and page faults occur as a result of a Lenovo BIOS specific SMI
> that runs during the D3->D0 transition on NVME devices.

Add the DMI ids for another variant of the T14s Gen1, which also needs
the s2idle quirk.

Link: https://lore.kernel.org/all/20220503183420.348-1-mario.limonciello@amd.com/
Link: https://bbs.archlinux.org/viewtopic.php?pid=2084655#p2084655
Signed-off-by: Benjamin Asbach <asbachb.kernel@impl.it>
Tested-by: Benjamin Asbach <asbachb.kernel@impl.it>
Link: https://lore.kernel.org/r/20230331232447.37204-1-asbachb.kernel@impl.it
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

platform/x86: think-lmi: Clean up display of current_value on Thinkstation

On ThinkStations on retrieving the attribute value the BIOS appends the
possible values to the string.
Clean up the display in the current_value_show function so the options
part is not displayed.

Fixes: a40cd7ef22fb ("platform/x86: think-lmi: Add WMI interface support on Lenovo platforms")
Reported by Mario Limoncello <Mario.Limonciello@amd.com>
Link: https://github.com/fwupd/fwupd/issues/5077#issuecomment-1488730526
Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20230403013120.2105-2-mpearson-lenovo@squebb.ca
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

platform/x86: think-lmi: Fix memory leaks when parsing ThinkStation WMI strings

My previous commit introduced a memory leak where the item allocated
from tlmi_setting was not freed.
This commit also renames it to avoid confusion with the similarly name
variable in the same function.

Fixes: 8a02d70679fc ("platform/x86: think-lmi: Add possible_values for ThinkStation")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Link: https://lore.kernel.org/lkml/df26ff45-8933-f2b3-25f4-6ee51ccda7d8@gmx.de/T/
Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20230403013120.2105-1-mpearson-lenovo@squebb.ca
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>