Michal Simek [Mon, 21 Nov 2016 09:43:37 +0000 (10:43 +0100)]
ARM: zynq: Remove spi-max-frequency
spi-max-frequency for spi bus depends on devices which are
connected to it. Remove this parameter from dtsi file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 27 Jul 2016 12:44:30 +0000 (14:44 +0200)]
ARM: zynq: Remove CONFIG_BOOTP_SERVERIP
Do the same change which was done in ZynqMP by:
"ARM64: zynqmp: Remove CONFIG_BOOTP_SERVERIP"
(sha1:
a8b6a156c0f7fb99502229e454bc9c3b38645280)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 16 Dec 2016 10:57:17 +0000 (11:57 +0100)]
ARM: zynq: Move CONFIG_SYS_TEXT_BASE to Kconfig
Enable CONFIG_SYS_TEXT_BASE via Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 16 Dec 2016 09:01:45 +0000 (10:01 +0100)]
fpga: zynqmp: Remove empty functions
Xilinx core files will take care about it.
There is no need to have these functions because they do nothing.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Siva Durga Prasad Paladugu [Fri, 18 Nov 2016 04:57:48 +0000 (10:27 +0530)]
ARM64: zynqmp: Add support to save env to FAT
Add support to save environment as a file of FAT filesystem
on to SD card. The file will be saved with name uEnv.txt.
This environment will be retrieved during boot.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Siva Durga Prasad Paladugu [Fri, 18 Nov 2016 04:57:47 +0000 (10:27 +0530)]
ARM64: zynqmp: Increase environment size to 32K
Increase environment size to 32K as the current default
environment itself is greater than 4K.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 10 May 2016 11:11:19 +0000 (13:11 +0200)]
microblaze: Enable option to overwrite default variables
Enable overwriting variables out of main config file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 16 Dec 2016 08:12:10 +0000 (09:12 +0100)]
microblaze: Remove hardcoded IP address from config
IP addresses shouldn't be hardcoded in board config.
This patch removes them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Sai Pavan Boddu [Tue, 16 Aug 2016 11:42:05 +0000 (17:12 +0530)]
microblaze: Make the board configuration name user definable
Add a prompt for editing in menuconfig
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 12 Dec 2016 08:47:26 +0000 (09:47 +0100)]
net: gem: Use wait_for_bit() instead of private mdio_wait()
Using generic wait_for_bit() implementation instead of
using private wait function.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 12 Dec 2016 08:46:09 +0000 (09:46 +0100)]
lib: Add WATCHDOG_RESET to wait_bit.h
wait_for_bit() is missing reset watchdog in case watchdog
is configured.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 9 Jan 2017 16:57:05 +0000 (11:57 -0500)]
Prepare v2017.01
Signed-off-by: Tom Rini <trini@konsulko.com>
Ladislav Michl [Mon, 9 Jan 2017 10:33:28 +0000 (11:33 +0100)]
lib: gitignore *.elf and *.so generated by efi_loader
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tom Rini [Mon, 9 Jan 2017 01:16:00 +0000 (20:16 -0500)]
scripts/config_whitelist.txt: Resync
Signed-off-by: Tom Rini <trini@konsulko.com>
Jagan Teki [Thu, 5 Jan 2017 14:32:50 +0000 (15:32 +0100)]
mx6ullevk: Add missing MAINTAINERS for mx6ull_14x14_evk_plugin_defconfig
Add 'Peng Fan' as MAINTAINERS of configs/mx6ull_14x14_evk_plugin_defconfig
which is missing in below commit
"imx: mx6ull_14x14_evk: add plugin defconfig"
(sha1:
b90ebf49bb8f74afe68f696f59a0e24cc79f2031)
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Andrew F. Davis [Fri, 6 Jan 2017 22:32:12 +0000 (16:32 -0600)]
am335x: configs: Use ISW_ENTRY_ADDR to set SPL_TEXT_BASE
The SPL load address changes based on boot type in HS devices,
ISW_ENTRY_ADDR is used to set this address for AM43xx based SoCs
for similar reasons. Add this same logic for AM33xx devices.
Also make the default value for ISW_ENTRY_ADDR correct for GP
devices based on SoC, HS devices already pick the correct
value in their defconfig.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Andrew F. Davis [Fri, 6 Jan 2017 22:20:02 +0000 (16:20 -0600)]
arm: mach-omap2: Fix secure file generation
When TI_SECURE_DEV_PKG is not defined we warn that the file '*_HS' was
not generated but generate an unsigned one anyway, first fix this
warning to say that it was generated but not secured.
When the user then exports TI_SECURE_DEV_PKG after getting this warning,
and tries to re-build, 'make' will detect the build artifacts as
unchanged and so assume they do not need to be re-generated. This causes
it to fail to sign the files and it will pack unsigned files into the
final image, even though TI_SECURE_DEV_PKG is now correctly defined and
working.
Fix this by using FORCE on the targets causes them to be re-run even if
the dependent files have not changed.
This then causes another issue. We currently rename the signed dtb files
to overwrite the non-signed ones. We do this so the 'mkimage' tool gives
the packaged dtb sections the correct name. If we do not rename the files
then SPL will not find them during boot.
Fix this by renaming the dtb files by appending _HS to the end of the
filename, after the ".dtb", this causes them to still be named correctly
in the FIT blob.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tom Rini [Thu, 5 Jan 2017 00:41:50 +0000 (19:41 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-tegra
Tom Rini [Thu, 5 Jan 2017 00:41:23 +0000 (19:41 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-spi
York Sun [Wed, 28 Dec 2016 16:43:50 +0000 (08:43 -0800)]
powerpc: mpc85xx: Move macro CONFIG_SYS_PPC64 to Kconfig
Use Kconfig option SYS_PPC64 instead.
Signed-off-by: York Sun <york.sun@nxp.com>
York Sun [Wed, 28 Dec 2016 16:43:49 +0000 (08:43 -0800)]
powerpc: mpc85xx: Move CONFIG_SYS_FSL_QORIQ_CHASSIS* to Kconfig
Use Kconfig option to select chassis version.
Signed-off-by: York Sun <york.sun@nxp.com>
York Sun [Wed, 28 Dec 2016 16:43:48 +0000 (08:43 -0800)]
powerpc: E6500: Move macro CONFIG_E6500 to Kconfig
Use Kconfig option E6500 and clean up existing usage.
Signed-off-by: York Sun <york.sun@nxp.com>
York Sun [Wed, 28 Dec 2016 16:43:47 +0000 (08:43 -0800)]
powerpc: mpc85xx: Remove unused ifdef in config header
After most config options are moved to Kconfig, the unused ifdef
or elif can be removed.
Signed-off-by: York Sun <york.sun@nxp.com>
York Sun [Wed, 28 Dec 2016 16:43:46 +0000 (08:43 -0800)]
ddr: fsl: Move CONFIG_SYS_FSL_DDR_VER to Kconfig
Use Kconfig to select DDR version instead of using config header.
Signed-off-by: York Sun <york.sun@nxp.com>
York Sun [Wed, 28 Dec 2016 16:43:45 +0000 (08:43 -0800)]
ddr: fsl: Merge macro CONFIG_NUM_DDR_CONTROLLERS and CONFIG_SYS_NUM_DDR_CTRLS
These two macros are used for the same thing, the total number of DDR
controllers for a given SoC. Use SYS_NUM_DDR_CTRLS in Kconfig and
merge existing usage.
Signed-off-by: York Sun <york.sun@nxp.com>
York Sun [Wed, 28 Dec 2016 16:43:44 +0000 (08:43 -0800)]
ddr: fsl: Move macro CONFIG_NUM_DDR_CONTROLLERS to Kconfig
Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing
usage in ls102xa and fsl-layerscape. Remove all powerpc macros in
config header and board header files.
Signed-off-by: York Sun <york.sun@nxp.com>
York Sun [Wed, 28 Dec 2016 16:43:43 +0000 (08:43 -0800)]
powerpc: mpc85xx: Move CONFIG_SYS_FSL_ERRATUM_* to Kconfig
Use Kconfig to select errata workaround.
Signed-off-by: York Sun <york.sun@nxp.com>
York Sun [Wed, 28 Dec 2016 16:43:42 +0000 (08:43 -0800)]
mmc: move CONFIG_SYS_FSL_ERRATUM_ESDHC* to Kconfig
Add option SYS_FSL_ERRATUM_ESDHC111, SYS_FSL_ERRATUM_ESDHC13,
SYS_FSL_ERRATUM_ESDHC135, SYS_FSL_ERRATUM_ESDHC_A001 to mmc Kconfig.
Move existing macros to related Kconfig.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate bk4r1]
Signed-off-by: Tom Rini <trini@konsulko.com>
York Sun [Wed, 28 Dec 2016 16:43:41 +0000 (08:43 -0800)]
arm: layerscape: Move CONFIG_SYS_FSL_ERRATUM_* to Kconfig
Use Kconfig to select errata workaround.
Signed-off-by: York Sun <york.sun@nxp.com>
York Sun [Wed, 28 Dec 2016 16:43:40 +0000 (08:43 -0800)]
fsl_ddr: Move DDR config options to driver Kconfig
Create driver/ddr/fsl/Kconfig and move existing options. Clean up
existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s]
Signed-off-by: Tom Rini <trini@konsulko.com>
York Sun [Wed, 28 Dec 2016 16:43:39 +0000 (08:43 -0800)]
powerpc: T104xQDS: Remove macro CONFIG_T104xD4QDS
Remove this macro. It was added by
e622d9ed but actually wasn't used.
Signed-off-by: York Sun <york.sun@nxp.com>
York Sun [Wed, 28 Dec 2016 16:43:38 +0000 (08:43 -0800)]
powerpc: T2081QDS: Remove macro T2081QDS
Use TARGET_T2081QDS from Kconfig instead.
Signed-off-by: York Sun <york.sun@nxp.com>
York Sun [Wed, 28 Dec 2016 16:43:37 +0000 (08:43 -0800)]
powerpc: T2080RDB: Remove macro CONFIG_T2080RDB
Use TARGET_T2080RDB from Kconfig instead.
Signed-off-by: York Sun <york.sun@nxp.com>
York Sun [Wed, 28 Dec 2016 16:43:36 +0000 (08:43 -0800)]
powerpc: T2080QDS: Remove macro T2080QDS
Use TARGET_T2080QDS from Kconfig instead.
Signed-off-by: York Sun <york.sun@nxp.com>
York Sun [Wed, 28 Dec 2016 16:43:35 +0000 (08:43 -0800)]
powerpc: T1040QDS: Remove macro CONFIG_T1040QDS
Use TARGET_T1040QDS from Kconfig instead.
Signed-off-by: York Sun <york.sun@nxp.com>
York Sun [Wed, 28 Dec 2016 16:43:34 +0000 (08:43 -0800)]
powerpc: T1024RDB: Remove macro CONFIG_T1024RDB
Use TARGET_T1024RDB from Kconfig instead.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Get missing hunk in board/freescale/t102xrdb/ddr.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
York Sun [Wed, 28 Dec 2016 16:43:33 +0000 (08:43 -0800)]
powerpc: T1023RDB: Remove macro CONFIG_T1023RDB
Use TARGET_T1023RDB from Kconfig instead.
Signed-off-by: York Sun <york.sun@nxp.com>
York Sun [Wed, 28 Dec 2016 16:43:32 +0000 (08:43 -0800)]
powerpc: mpc85xx: Remove variant SoCs T1020/T1022/T1013/T1014
Remove these SoCs from Kconfig because they don't have individual
configuration. Clean up existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
York Sun [Wed, 28 Dec 2016 16:43:31 +0000 (08:43 -0800)]
crypto: Move CONFIG_SYS_FSL_SEC_LE and _BE to Kconfig
Use Kconfig option to set little- or big-endian access to secure
boot and trust architecture.
Signed-off-by: York Sun <york.sun@nxp.com>
York Sun [Wed, 28 Dec 2016 16:43:30 +0000 (08:43 -0800)]
crypto: Move SYS_FSL_SEC_COMPAT into driver Kconfig
Instead of define CONFIG_SYS_FSL_SEC_COMPAT in header files for PowerPC
and ARM SoCs, move it to Kconfig under the driver.
Signed-off-by: York Sun <york.sun@nxp.com>
York Sun [Wed, 28 Dec 2016 16:43:29 +0000 (08:43 -0800)]
powerpc: mpc85xx: Move CONFIG_SYS_PPC_E500_DEBUG_TLB to Kconfig
Use Kconfig SYS_PPC_E500_DEBUG_TLB and clean up existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate 8572]
Signed-off-by: Tom Rini <trini@konsulko.com>
York Sun [Wed, 28 Dec 2016 16:43:28 +0000 (08:43 -0800)]
powerpc: mpc85xx: Move CONFIG_SYS_NUM_TLBCAMS to Kconfig
Use Kconfig option for SYS_NUM_TLBCAMS and clean up existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
York Sun [Wed, 28 Dec 2016 16:43:27 +0000 (08:43 -0800)]
powerpc: E500: Move CONFIG_E500 and CONFIG_E500MC to Kconfig
Use Kconfig option for E500 and E500MC macros.
Signed-off-by: York Sun <york.sun@nxp.com>
Jagan Teki [Mon, 2 Jan 2017 23:24:36 +0000 (00:24 +0100)]
mtd: nand: mxs_nand_spl: Fix to remove twise 'NAND' print
SPL from nand will print 'NAND' in boot_from_devices based on
the image_loader name, remove the extra 'NAND ' in mxs_nand_spl driver.
Original behaviour:
-------------------
U-Boot SPL 2017.01-rc2-gf84dd8b (Jan 02 2017 - 22:24:19)
Trying to boot from NANDNAND : 512 MiB
After the fix:
-------------
U-Boot SPL 2017.01-rc2-gf84dd8b-dirty (Jan 02 2017 - 23:17:00)
Trying to boot from NAND: 512 MiB
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Vignesh R [Wed, 21 Dec 2016 05:12:33 +0000 (10:42 +0530)]
spi: cadence_qspi_apb: Use 32 bit indirect read transaction when possible
According to Section 11.15.4.9.1 Indirect Read Controller of K2G SoC
TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit
data interface reads until the last word of an indirect transfer
So, make sure that QSPI indirect reads are 32 bit sized except for the
final read. If the rxbuf is unaligned then use bounce buffer, so that
readsl() can be used instead of readsb() to avoid non 32-bit accesses.
[1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Vignesh R [Wed, 21 Dec 2016 05:12:32 +0000 (10:42 +0530)]
spi: cadence_qspi_apb: Use 32 bit indirect write transaction when possible
According to Section 11.15.4.9.2 Indirect Write Controller of K2G SoC
TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit
data interface writes until the last word of an indirect transfer
otherwise indirect writes is known to fails sometimes. So, make sure
that QSPI indirect writes are 32 bit sized except for the last write. If
the txbuf is unaligned then use bounce buffer to avoid data aborts.
So, now that the driver uses bounce_buffer, enable CONFIG_BOUNCE_BUFFER
for all boards that use Cadence QSPI driver.
[1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Misha Komarovskiy [Sun, 11 Dec 2016 19:28:12 +0000 (22:28 +0300)]
ARM: dts: tegra: Sync paz00 with Linux 4.8
Sync with Linux 4.8 dts plus vdd_bl regulator
to fix backlight start, display timings and USB
controller aliases fix.
Signed-off-by: Misha Komarovskiy <zombah@gmail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Marcel Ziswiler [Mon, 19 Dec 2016 14:38:07 +0000 (15:38 +0100)]
colibri_t20: fix ulpi reset polarity
Fix ULPI reset polarity which caused a hard hang on Colibri T20 upon
attempting to start the USB subsystem:
This fixes my late commit
d5a24d8b53d350364bd429b7104ec369b817e4b8
(colibri_t20: fix usb operation and controller order) inadvertently
having overwritten Stephen's previous commit
2f6a7e8ce5df8b99d84bfd486c6f99d92322ce04 (ARM: tegra: fix USB ULPI PHY
reset signal inversion confusion).
While at it also fix comment about on-module USB port.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Marcel Ziswiler [Mon, 19 Dec 2016 14:38:06 +0000 (15:38 +0100)]
apalis_t30: comment about disabled pcie nodes
Add a comment about the disabled PCIe port nodes.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Marcel Ziswiler [Mon, 19 Dec 2016 14:38:05 +0000 (15:38 +0100)]
pci: kconfig: fix spelling in description
Fix 'driver model' rather than 'driver mode' in description.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Marcel Ziswiler [Mon, 19 Dec 2016 14:38:04 +0000 (15:38 +0100)]
video: tegra: fix spelling in comment
Get rid of spurious 'are' in the comment.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Fri, 2 Dec 2016 19:26:42 +0000 (12:26 -0700)]
ARM: tegra: allow passing cboot DTB to the kernel
Some users may wish to pass the cboot-supplied DTB to the booted kernel
rather than having U-Boot load the DTB itself. To allow this, expose the
address of the cboot-supplied DTB in environment variable $fdt_addr. At
least when using extlinux.conf, if the user doesn't explicitly specify
which DTB to pass to the kernel, U-Boot passes the DTB referred to by
this variable.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tom Rini [Tue, 3 Jan 2017 01:00:55 +0000 (20:00 -0500)]
Prepare v2017.01-rc3
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 2 Jan 2017 21:32:05 +0000 (16:32 -0500)]
Merge branch 'master' of git://denx.de/git/u-boot-imx
Fabio Estevam [Mon, 2 Jan 2017 10:44:04 +0000 (08:44 -0200)]
udoo: neo: Fix indentation
The standard way is to put ifdef/endif in the very first column.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Jagan Teki [Wed, 21 Dec 2016 21:14:46 +0000 (22:14 +0100)]
imx6ul: geam6ul: Enable I2C support
Enable I2C support for Engicam GEAM6UL NAND module.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 21 Dec 2016 11:02:13 +0000 (12:02 +0100)]
imx6ul: geam6ul: Add MAINTAINERS for nand_defconfig
Add Jagan as MAINTAINERS of configs/imx6ul_geam_nand_defconfig
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 21 Dec 2016 11:00:29 +0000 (12:00 +0100)]
configs: engicam: Add fitboot env support
Add FIT image booting from MMC device, during MMC bootcmd
u-boot env script look for bootscript, else fit image or else
finally look for legacy image uImage.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 21 Dec 2016 11:00:28 +0000 (12:00 +0100)]
configs: engicam: Cleanup on mmcboot env
- Add tab space
- remove exctra 'mmc dev ${mmcdev}'
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 21 Dec 2016 11:00:27 +0000 (12:00 +0100)]
configs: engicam: Enable CONFIG_IMAGE_FORMAT_LEGACY
Enabling FIT along with Signature will make bootm to
not-understanding u-boot legacy image formats like uImage, etc.
So this patch enabling legacy image format for backward compatibility.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 21 Dec 2016 11:00:26 +0000 (12:00 +0100)]
defconfigs: imx6: engicam: Enable FIT
Enable Flattened Image Tree support for all Engicam boards.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 21 Dec 2016 11:00:25 +0000 (12:00 +0100)]
imx6: engicam: Add nandboot env support
Add config options for booting Linux from NAND in UBI format.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 21 Dec 2016 11:00:24 +0000 (12:00 +0100)]
defconfigs: engicam: Enable UBI commands
Create ubifs.img:
$ mkfs.ubifs -q -r /rootfs -m 4096 -e 253952 -c 7936 -o ubifs.img
Write ubifs.img:
---------------
icorem6qdl> nand erase.part rootfs
icorem6qdl> ubi part rootfs
icorem6qdl> ubi create rootfs
icorem6qdl> ext4load mmc 0:2 ${loadaddr} ubifs.img
166592512 bytes read in 8091 ms (19.6 MiB/s)
icorem6qdl> ubi write ${loadaddr} rootfs ${filesize}
166592512 bytes written to volume rootfs
icorem6qdl> ubifsmount ubi0:rootfs
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 21 Dec 2016 11:00:23 +0000 (12:00 +0100)]
defconfigs: engicam: Enable MMC commands in nand
For writing Linux or rootfs on to NAND, the best suitable way
is to use MMC commands since MMC driver by default enabled by
mx6_common.h, hence enabled MMC commands in nand defconfigs.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 21 Dec 2016 11:00:22 +0000 (12:00 +0100)]
configs: engicam: Rename nand with gpmi-name in mtdparts
gpmi-nand is the proper name used in nand driver from Linux for all
imx related nand boards, so rename mtdparts name as gpmi-nand instead
of nand, this will eventually reflects all nand info to Linux from
u-boot like mtdparts.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 21 Dec 2016 11:00:21 +0000 (12:00 +0100)]
imx6: engicam: Use bootm instead of bootz
Boot Linux with uImage instead of zImage, so update
bootz with bootm.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 21 Dec 2016 11:00:20 +0000 (12:00 +0100)]
configs: engicam: Increase nand kernel partition size
Increase the nand kernel partition size, for supporting
large uImage files, maximum 8MiB.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Uri Mashiach [Wed, 28 Dec 2016 16:28:36 +0000 (18:28 +0200)]
arm: am57xx: cl-som-am57x: update default env
Modify U-Boot default env settings.
Boot sequence:
1. SD card boot script
2. SD card boot no script
3. SATA boot script
4. SATA boot no script
5. eMMC boot script
6. eMMC boot no script
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Dmitry Lifshitz [Wed, 28 Dec 2016 16:28:35 +0000 (18:28 +0200)]
arm: am57xx: cl-som-am57x: add ETH support
Add MAC support.
Use PHY, connected to RGMII1 as a default Eth adapter,
by appropriate setting of 'cpsw_data.active_slave'.
'cpsw_phy' env variable can override this setting.
Set the MAC addresses in the U-Boot environment.
The addresses are retrieved from the on-board EEPROM or from the SOC's
MAC fuses.
Set the following PHYs RGMII clock delays:
- Enable RX delay
- Disable TX delay
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
[uri.mashiach@compulab.co.il: add RGMII clock delays]
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Dmitry Lifshitz [Wed, 28 Dec 2016 16:28:34 +0000 (18:28 +0200)]
arm: am57xx: cl-som-am57x: fetch board rev from EEPROM
Add PCB revision message.
Implement board revision get_board_rev API.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Commit description update.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Dmitry Lifshitz [Wed, 28 Dec 2016 16:28:33 +0000 (18:28 +0200)]
arm: am57xx: cl-som-am57x: add initial board support
Features supported :
* Serial console
* SPI Flash
* MMC/SD Card
* eMMC storage
* SATA
* PCA9555 - GPIO expander over I2C5 bus
* USB
Use spl alternate boot device feature to define fallback to
the main boot device as it is defined by hardware.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
[uri.mashiach@compulab.co.il: Adjust to v2016.11]
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Emmanuel Vadot [Tue, 27 Dec 2016 21:36:08 +0000 (22:36 +0100)]
tools: binman: Use /usr/bin/env to find python executable
Some OS (all BSD and probably others) do not have python in /usr/bin
but in another directory.
It is a common usage to use /usr/bin/env python as shebang for python
scripts so use this for binman.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Adam Ford [Sat, 31 Dec 2016 12:33:46 +0000 (06:33 -0600)]
OMAP3: omap3_logic: Remove display parameter
The display is done in the device tree now, and there is no need
to pass 'display' kernel parameter any longer.
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Sat, 31 Dec 2016 11:51:27 +0000 (05:51 -0600)]
ARM: OMAP3_LOGIC: Remove ONENAND config options
These boards do not and never have had ONENAND support, so let's remove it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Robert P. J. Day [Thu, 29 Dec 2016 10:23:19 +0000 (05:23 -0500)]
doc/README.cfi: Update code snippet, and add example.
First, update the code snippet referenced in the README file. And
since there are only two boards that override flash_cmd_reset(),
might as well show them both.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Robert P. J. Day [Thu, 29 Dec 2016 10:06:41 +0000 (05:06 -0500)]
digsy_mtc.c: Minor spelling/grammar fixes.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Fabio Estevam [Tue, 27 Dec 2016 01:04:41 +0000 (23:04 -0200)]
mx6qsabreauto: Fix the EIM clock for the mx6qp variant
On the MX6Q the aclk_eim_slow_podf field is '1' after POR, while on the
MX6DQP it is '3'.
This makes the EIM clock to be only 66MHz on the mx6qp variant, instead of
132 MHz.
Instead of relying on the POR values for the CSMR1 register, make sure to
manually configure the clk_eim_slow_sel field as '00' so that EIM clock is
derived from AXI clock and the aclk_eim_slow_podf field as '1' so that EIM
clock can be AXI clock divided by 2.
This way a consistent EIM clock frequency is configured for all the mx6
variants.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Kevin Hilman [Fri, 16 Dec 2016 21:08:10 +0000 (13:08 -0800)]
ARM: imx7s-warp: enable USB gadget ethernet
Enable USB gadget ethernet by default to have networking capabilities.
Tested using DHCP and TFTP to transfer kernel, DT, ramdisk.
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Fabio Estevam [Thu, 15 Dec 2016 22:10:08 +0000 (20:10 -0200)]
udoo_neo: Use 'fdtfile' variable name
'fdtfile' is the preferred name for the variable that contains the
device tree blob according to the README file.
It also makes it consistent with other i.MX boards that use config_distro,
so change it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Peng Fan [Fri, 2 Dec 2016 05:43:03 +0000 (13:43 +0800)]
imx: thermal: Kconfig: add MX7
The thermal drivers support i.MX6 and i.MX7, add MX7 in Kconfig file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Sven Ebenfeld [Sun, 6 Nov 2016 15:37:58 +0000 (16:37 +0100)]
Makefile: preserve output for images that can contain HAB Blocks
To being able to sign created binaries, we need to know the HAB Blocks
for that image. Especially for the imximage type the HAB Blocks are
only available during creation of the image. We want to preserve the
information until we get to sign the files.
In the verbose case we still get them printed out instead of writing
to log files.
Cc: sbabic@denx.de
v2-Changes:
- No usage of MKIMAGEOUTPUT_$(@F) macro.
- Predefine default value /dev/null in every involved Makefile.
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Sven Ebenfeld [Sun, 6 Nov 2016 15:37:57 +0000 (16:37 +0100)]
doc: imx6: add section for secure boot with SPL
Cc: sbabic@denx.de
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Sven Ebenfeld [Sun, 6 Nov 2016 15:37:56 +0000 (16:37 +0100)]
tools: mkimage: add firmware-ivt image type for HAB verification
When we want to use Secure Boot with HAB from SPL over U-Boot.img,
we need to append the IVT to the image and leave space for the CSF.
Images generated as firmware_ivt can directly be signed using the
Freescale code signing tool. For creation of a CSF, mkimage outputs
the correct HAB Blocks for the image.
The changes to the usual firmware image class are quite small,
that is why I implemented that directly into the default_image.
Cc: sbabic@denx.de
v2-Changes: None
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Sven Ebenfeld [Sun, 6 Nov 2016 15:37:55 +0000 (16:37 +0100)]
arm: imx: add HAB authentication of image to SPL boot
When using HAB as secure boot mechanism on Wandboard, the chain of
trust breaks immediately after the SPL. As this is not checking
the authenticity of the loaded image before jumping to it.
The HAB status output will not be implemented in SPL as it adds
a lot of strings that are only required in debug cases. With those
it exceeds the maximum size of the available OCRAM (69 KiB).
The SPL MISC driver support must be enabled, so that the driver can use OTP fuse
to check if HAB is enabled.
Cc: sbabic@denx.de
v2-Changes: None
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Sven Ebenfeld [Sun, 6 Nov 2016 15:37:54 +0000 (16:37 +0100)]
arm: imx: remove bmode , hdmidet and dek commands from SPL
These files are blowing up the SPL and should not be required
there as the SPL delivers no command console. Because building fails
for mx27 and mx31 machines with SPL build, we remove the linker flag
for them from the Makefile. Nothing is built for them to be linked
in that directory.
Cc: sbabic@denx.de
v2 Changes:
- Remove mx27 and mx31 from Makefile during SPL build as nothing is built for
them in that directory. And removing the commands with the libs-y directive
lead to linker failures. e.g. "armv5te-ld.bfd: cannot find arch/arm/imx-common/built-in.o: No such file or directory)"
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Fabio Estevam [Fri, 16 Dec 2016 13:18:32 +0000 (11:18 -0200)]
udoo_neo: Remove USDHC3 entry
Commit
c94981efa20cc58 ("udoo_neo: Remove USDHC3 support") removed
the SDHC3 support, but missed to remove the entry from the usdhc_cfg
structure, so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Masahiro Yamada [Wed, 7 Dec 2016 13:10:30 +0000 (22:10 +0900)]
mmc: move MMC_SDHCI_IO_ACCESSORS to Kconfig
This is a user-unconfigurable option that is selected by the
drivers that need to overwrite SDHCI IO memory accessors.
(BCM2835 SDHCI seems the only driver that needs to do so.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Masahiro Yamada [Wed, 7 Dec 2016 13:10:29 +0000 (22:10 +0900)]
mmc: move some SDHCI related options to Kconfig
While I moved the options, I also renamed them so that they are all
prefixed with MMC_SDHCI_.
This commit was created in the following steps.
[1] Rename with the following command
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_MMC_SDMA/CONFIG_MMC_SDHCI_SDMA/g
s/CONFIG_BCM2835_SDHCI/CONFIG_MMC_SDHCI_BCM2835/g
s/CONFIG_KONA_SDHCI/CONFIG_MMC_SDHCI_KONA/g
s/CONFIG_MV_SDHCI/CONFIG_MMC_SDHCI_MV/g
s/CONFIG_S5P_SDHCI/CONFIG_MMC_SDHCI_S5P/g
s/CONFIG_SPEAR_SDHCI/CONFIG_MMC_SDHCI_SPEAR/g
'
[2] create the Kconfig entries in drivers/mmc/Kconfig
[3] Move the options by the following command
tools/moveconfig.py -y MMC_SDHCI_SDMA MMC_SDHCI_BCM2835 \
MMC_SDHCI_KONA MMC_SDHCI_MV MMC_SDHCI_S5P MMC_SDHCI_SPEAR
[4] Sort drivers/mmc/Makefile for readability
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Masahiro Yamada [Wed, 7 Dec 2016 13:10:28 +0000 (22:10 +0900)]
mmc: move CONFIG_SDHCI to Kconfig, renaming to CONFIG_MMC_SDHCI
Move CONFIG_SDHCI to Kconfig and rename it to CONFIG_MMC_SDHCI.
My motivation for the rename is, ultimately, to make all the MMC
options prefixed with MMC_ and SDHCI options with MMC_SDHCI_,
like Linux.
This commit was created as follows:
[1] Rename the config option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_SDHCI/CONFIG_MMC_SDHCI/g'
[2] create the entry for MMC_SDHCI in drivers/mmc/Kconfig
[3] run "tools/moveconfig.py -y MMC_SDHCI"
[4] add "depends on MMC_SDHCI" to existing SDHCI driver entries
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Masahiro Yamada [Wed, 7 Dec 2016 13:10:27 +0000 (22:10 +0900)]
mmc: make MMC driver entries dependent on MMC
Currently, CONFIG_MMC is not related to any other options by
"depends on" or "select". One of big advantages of using Kconfig
is automatic dependency tracking, but the current state is lacking
it. As the first step, make the existing MMC driver entries depend
on MMC.
This commit was created by the following steps:
[1] Run the following script:
--------------------8<--------------------
rm -f tmp.txt
for d in $(find . -path './configs/*_defconfig')
do
if grep -q -e 'CONFIG_MSM_SDHCI=y' $d ||
grep -q -e 'CONFIG_ATMEL_SDHCI=y' $d ||
grep -q -e 'CONFIG_ROCKCHIP_DWMMC=y' $d ||
grep -q -e 'CONFIG_SH_SDHI=y' $d ||
grep -q -e 'CONFIG_PIC32_SDHCI=y' $d ||
grep -q -e 'CONFIG_ZYNQ_SDHCI=y' $d ||
grep -q -e 'CONFIG_ROCKCHIP_SDHCI=y' $d ||
grep -q -e 'CONFIG_MMC_UNIPHIER=y' $d ||
grep -q -e 'CONFIG_SANDBOX_MMC=y' $d
then
echo CONFIG_MMC=y >> $d
echo ${d#./configs/} >> tmp.txt
fi
done
tools/moveconfig.py -y -s -d tmp.txt
rm tmp.txt
--------------------8<--------------------
[2] surround MMC driver entries with "if MMC" and "endif"
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Masahiro Yamada [Wed, 7 Dec 2016 13:10:26 +0000 (22:10 +0900)]
mmc: complete unfinished move of CONFIG_MMC
Commit
7a777f6d6f35 ("mmc: Add generic Kconfig option") created
a Kconfig entry for this option without any actual moves, then
commit
44c798799f66 ("sunxi: Use Kconfig CONFIG_MMC") moved
instances only for SUNXI.
We generally do not like such partial moves. This kind of work
is automated by tools/moveconfig.py, so it is pretty easy to
complete this move.
I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
This shortens the configs and will ease new board porting.
This commit was created as follows:
[1] Edit Kconfig (remove the "depends on", add the "default",
copy the prompt and help message from Linux)
[2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Masahiro Yamada [Wed, 7 Dec 2016 13:10:25 +0000 (22:10 +0900)]
Sync defconfig files by savedefconfig
Generated by "tools/moveconfig -s".
This will make config moves easier.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Peng Fan [Tue, 27 Dec 2016 12:19:07 +0000 (20:19 +0800)]
imx: mx6sllevk: add MAINTAINERS file
add MAINTAINERS files
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Jaehoon Chung [Tue, 27 Dec 2016 11:08:13 +0000 (20:08 +0900)]
board: samsung: update the MAINTAINERS file
Update the maintainer from Przemyslaw and Lukasz to me.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Baruch Siach [Tue, 27 Dec 2016 09:03:29 +0000 (11:03 +0200)]
cmd: net: fix function name in comment
In commit
7044c6bb6 (net: cosmetic: Clean up DHCP variables and functions)
BootpCopyNetParams() was renamed to store_net_params(). Update the reference in
comment.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Stefan Brüns [Tue, 27 Dec 2016 01:35:08 +0000 (02:35 +0100)]
fs/ext4: Initialize group descriptor size for revision level 0 filesystems
genext2fs creates revision level 0 filesystems, which are not readable
by u-boot due to the initialized group descriptor size field.
f798b1dda1c5de818b806189e523d1b75db7e72d
Reported-by: Kever Yang <kever.yang@rock-chips.com>
Reported-by: FrostyBytes@protonmail.com
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Jean-Jacques Hiblot [Fri, 23 Dec 2016 09:45:43 +0000 (10:45 +0100)]
disk: Fixed capacity message
With capacities getting bigger, we can see see messages with negative
numbers like "Capacity: 1907729.0 MB = 1863.0 GB (-
387938128 x 512)".
Here the printed LBA is -
387938128 when it should have been
3907029168.
To fix this, use the right format when displaying the unsigned integers.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reported-by: Yan Liu <yan-liu@ti.com>
Ajay Bhargav [Wed, 21 Dec 2016 07:58:06 +0000 (13:28 +0530)]
Update Maintainer and Author's email address
I am not longer using my old email address
"ajay.bhargav@einfochips.com". For U-Boot development email address is
now updated to contact@8051projects.net
Signed-off-by: Ajay Bhargav <contact@8051projects.net>
Michal Simek [Tue, 20 Dec 2016 08:58:31 +0000 (09:58 +0100)]
tools: mkimage: Call fclose in error path
This patch is fixing missing fclose() calls
in error patch introduced by:
"tools: mkimage: Use fstat instead of stat to avoid malicious hacks"
(sha1:
ebe0f53f48e8f9ecc823e533a85b05c13638c350)
Reported-by: Coverity (CID: 155064, 155065)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Mon, 19 Dec 2016 10:31:04 +0000 (19:31 +0900)]
README: remove description about CONFIG_USE_ARCH_MEMCPY/SET
These options are now described in the Kconfig help. We do not want
to maintain duplicated documentation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>