Jiri Pirko [Thu, 26 Mar 2009 00:23:38 +0000 (17:23 -0700)]
bonding: select current active slave when enslaving device for mode tlb and alb
I've hit an issue on my system when I've been using RealTek RTL8139D cards in
bonding interface in mode balancing-alb. When I enslave a card, the current
active slave (bond->curr_active_slave) is not set and the link is therefore
not functional.
----
# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.5.0 (November 4, 2008)
Bonding Mode: adaptive load balancing
Primary Slave: None
Currently Active Slave: None
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
Slave Interface: eth1
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:1f:1f:01:2f:22
----
The thing that gets it right is when I unplug the cable and then I put it back
into the NIC. Then the current active slave is set to eth1 and link is working
just fine. Here is dmesg log with bonding DEBUG messages turned on:
----
ADDRCONF(NETDEV_UP): bond0: link is not ready
event_dev: bond0, event: 1
IFF_MASTER
event_dev: bond0, event: 8
IFF_MASTER
bond_ioctl: master=bond0, cmd=35216
slave_dev=
cac5d800:
slave_dev->name=eth1:
eth1: ! NETIF_F_VLAN_CHALLENGED
event_dev: eth1, event: 8
eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1
event_dev: eth1, event: 1
event_dev: eth1, event: 8
IFF_SLAVE
Initial state of slave_dev is BOND_LINK_UP
bonding: bond0: enslaving eth1 as an active interface with an up link.
ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
event_dev: bond0, event: 4
IFF_MASTER
bond0: no IPv6 routers present
<<<<cable unplug>>>>
eth1: link down
event_dev: eth1, event: 4
IFF_SLAVE
bonding: bond0: link status definitely down for interface eth1, disabling it
event_dev: bond0, event: 4
IFF_MASTER
<<<<cable plug>>>>
eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1
event_dev: eth1, event: 4
IFF_SLAVE
bonding: bond0: link status definitely up for interface eth1.
bonding: bond0: making interface eth1 the new active one.
event_dev: eth1, event: 8
IFF_SLAVE
event_dev: eth1, event: 8
IFF_SLAVE
bonding: bond0: first active interface up!
event_dev: bond0, event: 4
IFF_MASTER
----
The current active slave is set by calling bond_select_active_slave() function
from bond_miimon_commit() function when the slave (eth1) link goes to state up.
I also tested this on other machine with Broadcom NetXtreme II BCM5708
1000Base-T NIC and there all works fine. The thing is that this adapter is down
and goes up after few seconds after it is enslaved.
This patch calls bond_select_active_slave() in bond_enslave() function for modes
alb and tlb and makes sure that the current active slave is set up properly even
when the slave state is already up. Tested on both systems, works fine.
Notice: The same problem can maybe also occrur in mode 8023AD but I'm unable to
test that.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Li Yang [Tue, 24 Mar 2009 23:15:33 +0000 (23:15 +0000)]
gianfar: reallocate skb when headroom is not enough for fcb
Gianfar uses a hardware header FCB for offloading. However when used
with bridging or IP forwarding, TX skb might not have enough headroom
for the FCB. Reallocate skb for such cases.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 24 Mar 2009 23:34:38 +0000 (23:34 +0000)]
Bump release date to 25Mar2009 and version to 0.22
This patch bumps the driver release date to March 25th 2009
and release version to 0.22.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 24 Mar 2009 23:34:35 +0000 (23:34 +0000)]
r6040: Fix second PHY address
This patch fixes the second PHY address which is strapped
to be at PHY address 3 instead of 2.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiko Carstens [Tue, 24 Mar 2009 20:57:19 +0000 (20:57 +0000)]
qeth: fix wait_event_timeout handling
wait_event_timeout just takes the numnber of jiffies to wait as
an argument. That value does not include jiffies itself.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Tue, 24 Mar 2009 20:57:18 +0000 (20:57 +0000)]
qeth: check for completion of a running recovery
When a recovery is started for a qeth device, additional invocations
to change a mac address, to configure a VLAN interface on top, or to
add multicast addresses should wait till recovery is finished,
otherwise recovery might fail.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Klaus-Dieter Wacker [Tue, 24 Mar 2009 20:57:17 +0000 (20:57 +0000)]
qeth: unregister MAC addresses during recovery.
qeth: Unregister MAC addresses from device (layer 2) during
recovery cycle. When the device is set online the MAC
addresses are registered again on the device.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Blaschka [Tue, 24 Mar 2009 20:57:16 +0000 (20:57 +0000)]
qeth: remove EDDP
Performance measurements showed EDDP does not lower CPU costs but increase
them. So we dump out EDDP code from qeth driver.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Blaschka [Tue, 24 Mar 2009 20:57:15 +0000 (20:57 +0000)]
qeth: add statistics for tx csum
Add statistics counter for software tx checksumming.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kay Sievers [Tue, 24 Mar 2009 20:57:14 +0000 (20:57 +0000)]
qeth: struct device - replace bus_id with dev_name(), dev_set_name()
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 25 Mar 2009 07:03:16 +0000 (00:03 -0700)]
rndis_wlan: Fix build with netdev_ops compat disabled.
Instead of storing a private ->set_multicast_list, just
have a private netdev ops.
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Mack [Wed, 25 Mar 2009 06:32:03 +0000 (23:32 -0700)]
ax88796: Add method to take MAC from platform data
Implement a way to provide the MAC address for ax88796 devices from
their platform data. Boards might decide to set the address
programmatically, taken from boot tags or other sources.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Mack [Wed, 25 Mar 2009 06:31:22 +0000 (23:31 -0700)]
drivers/net/ax88796.c: take IRQ flags from platform_device
This patch adds support to the ax88796 ethernet driver to take IRQ flags
given by the platform_device definition.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 25 Mar 2009 06:28:02 +0000 (23:28 -0700)]
e1000e: add support for 82574 device ID 0x10F6
Add device ID for a new variant of the 82574 adapter.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Acked-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Tue, 24 Mar 2009 16:24:51 +0000 (16:24 +0000)]
ipv6: Fix conflict resolutions during ipv6 binding
The ipv6 version of bind_conflict code calls ipv6_rcv_saddr_equal()
which at times wrongly identified intersections between addresses.
It particularly broke down under a few instances and caused erroneous
bind conflicts.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Tue, 24 Mar 2009 16:24:50 +0000 (16:24 +0000)]
ipv6: Make v4-mapped bindings consistent with IPv4
Binding to a v4-mapped address on an AF_INET6 socket should
produce the same result as binding to an IPv4 address on
AF_INET socket. The two are interchangable as v4-mapped
address is really a portability aid.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Tue, 24 Mar 2009 16:24:49 +0000 (16:24 +0000)]
ipv6: Allow ipv4 wildcard binds after ipv6 address binds
The IPv4 wildcard (0.0.0.0) address does not intersect
in any way with explicit IPv6 addresses. These two should
be permitted, but the IPv4 conflict code checks the ipv6only
bit as part of the test. Since binding to an explicit IPv6
address restricts the socket to only that IPv6 address, the
side-effect is that the socket behaves as v6-only. By
explicitely setting ipv6only in this case, allows the 2 binds
to succeed.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Tue, 24 Mar 2009 16:24:48 +0000 (16:24 +0000)]
ipv6: Disallow binding to v4-mapped address on v6-only socket.
A socket marked v6-only, can not receive or send traffic to v4-mapped
addresses. Thus allowing binding to v4-mapped address on such a
socket makes no sense.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Tue, 24 Mar 2009 23:40:13 +0000 (16:40 -0700)]
be2net: cleanup rx/tx rate calculations
Hi, Pls accept this patch to cleanup rx/tx rate calculations as follows:
- check for jiffies wraparound
- remove typecast of a denominator
- do rate calculation only in workqueue context periodically
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Tue, 24 Mar 2009 23:37:55 +0000 (16:37 -0700)]
netlink: add NETLINK_NO_ENOBUFS socket flag
This patch adds the NETLINK_NO_ENOBUFS socket flag. This flag can
be used by unicast and broadcast listeners to avoid receiving
ENOBUFS errors.
Generally speaking, ENOBUFS errors are useful to notify two things
to the listener:
a) You may increase the receiver buffer size via setsockopt().
b) You have lost messages, you may be out of sync.
In some cases, ignoring ENOBUFS errors can be useful. For example:
a) nfnetlink_queue: this subsystem does not have any sort of resync
method and you can decide to ignore ENOBUFS once you have set a
given buffer size.
b) ctnetlink: you can use this together with the socket flag
NETLINK_BROADCAST_SEND_ERROR to stop getting ENOBUFS errors as
you do not need to resync (packets whose event are not delivered
are drop to provide reliable logging and state-synchronization).
Moreover, the use of NETLINK_NO_ENOBUFS also reduces a "go up, go down"
effect in terms of performance which is due to the netlink congestion
control when the listener cannot back off. The effect is the following:
1) throughput rate goes up and netlink messages are inserted in the
receiver buffer.
2) Then, netlink buffer fills and overruns (set on nlk->state bit 0).
3) While the listener empties the receiver buffer, netlink keeps
dropping messages. Thus, throughput goes dramatically down.
4) Then, once the listener has emptied the buffer (nlk->state
bit 0 is set off), goto step 1.
This effect is easy to trigger with netlink broadcast under heavy
load, and it is more noticeable when using a big receiver buffer.
You can find some results in [1] that show this problem.
[1] http://1984.lsi.us.es/linux/netlink/
This patch also includes the use of sk_drop to account the number of
netlink messages drop due to overrun. This value is shown in
/proc/net/netlink.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Brice Goglin [Tue, 24 Mar 2009 23:32:13 +0000 (16:32 -0700)]
myri10ge: update firmware headers to 1.4.41
Update myri10ge firmware headers to firmware version 1.4.41.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vibi sreenivasan [Tue, 24 Mar 2009 23:30:20 +0000 (16:30 -0700)]
macb: fix warning "warning: unused variable `dev' "
Removed unused variable dev
Signed-off-by: vibi sreenivasan <vibi_sreenivasan@cms.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joakim Tjernlund [Fri, 20 Mar 2009 20:09:14 +0000 (21:09 +0100)]
ucc_geth: Convert to net_device_ops
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew H. Richter [Tue, 24 Mar 2009 03:27:51 +0000 (03:27 +0000)]
claw: fix minor findings from code analysis tool
This patch fixes two problems in the claw driver identified by
static code analysis:
o Change in case differentiation of received sense codes
o Use correct data length in claw hard_start_xmit routine
Signed-off-by: Andrew H. Richter <richtera@us.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joel A. Fowler [Tue, 24 Mar 2009 03:27:49 +0000 (03:27 +0000)]
ctcm: fix minor findings from code analysis tool
From: Ursula Braun <ursula.braun@de.ibm.com>
This patch fixes problems in the ctcm driver identified by
static code analysis:
o remove an unnecessary always true condition in ctcm_unpack_skb
o remove duplicate assignment in ctc_mpc_alloc_channel
o remove an unnecessary always true condition in ctcmpc_send_sweep_resp
o remove duplicate initialization in ctcmpc_unpack_skb
o shorten if condition in mpc_action_go_inop
o remove INOP event if mpc group is undefined in mpc_action_doxid7
Signed-off-by: Joel A. Fowler <fowlerja@us.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin [Tue, 24 Mar 2009 03:27:48 +0000 (03:27 +0000)]
ctcm: avoid wraparound in length of incoming data
Since the receive code should tolerate any incoming garbage, it
should be protected against a potential wraparound when manipulating
length values within incoming data.
block_len is unsigned, so a too large subtraction will cause a
wraparound.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Tue, 24 Mar 2009 03:27:47 +0000 (03:27 +0000)]
ctcm: invalid return code from hard_start_xmit
Avoid kernel warning by using the correct hard_start_xmit return
code NETDEV_TX_BUSY for skb requeuing.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Tue, 24 Mar 2009 03:27:46 +0000 (03:27 +0000)]
claw: invalid return codes from hard_start_xmit
Avoid kernel warnings by using the correct hard_start_xmit return
code NETDEV_TX_BUSY for skb requeuing.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Tue, 24 Mar 2009 03:27:45 +0000 (03:27 +0000)]
netiucv: invalid return code from hard_start_xmit
Avoid kernel warning by using the correct hard_start_xmit return
code NETDEV_TX_BUSY for skb requeuing.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Klaus-Dieter Wacker [Tue, 24 Mar 2009 03:27:44 +0000 (03:27 +0000)]
lcs: invalid return codes from hard_start_xmit.
Lcs hard_start_xmit routine issued return codes other than
defined for this interface. Now lcs returns only either
NETDEV_TX_OK or NETDEV_TX_BUSY.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Klaus-Dieter Wacker [Tue, 24 Mar 2009 03:27:43 +0000 (03:27 +0000)]
Use kthread instead of kernel_thread
Lcs uses low-level kernel_thread implementation.
All drivers should use <linux/kthread.h> API instead.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Josh Stone [Tue, 24 Mar 2009 09:44:28 +0000 (09:44 +0000)]
net: Add dependent headers to trace/skb.h
The tracing header needs to include definitions for the macros used and
the types referenced. This lets automated tracing tools like SystemTap
make use of the tracepoint without any specific knowledge of its
meaning (leaving that to the user).
Signed-off-by: Josh Stone <jistone@redhat.com>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 24 Mar 2009 21:15:22 +0000 (14:15 -0700)]
arp_tables: ifname_compare() can assume 16bit alignment
Arches without efficient unaligned access can still perform a loop
assuming 16bit alignment in ifname_compare()
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Engelhardt [Tue, 24 Mar 2009 20:35:27 +0000 (13:35 -0700)]
netfilter: trivial Kconfig spelling fixes
Supplements commit
67c0d57930ff9a24c6c34abee1b01f7716a9b0e2.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 24 Mar 2009 20:24:36 +0000 (13:24 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/kaber/nf-next-2.6
Anton Vorontsov [Tue, 24 Mar 2009 19:06:46 +0000 (12:06 -0700)]
ucc_geth: Fix build breakage caused by a merge
This patch fixes following build error:
CC ucc_geth.o
ucc_geth.c: In function 'ucc_geth_probe':
ucc_geth.c:3644: error: implicit declaration of function 'uec_mdio_bus_name'
make[2]: *** [ucc_geth.o] Error 1
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 24 Mar 2009 13:26:50 +0000 (14:26 +0100)]
netfilter: nf_conntrack: Reduce conntrack count in nf_conntrack_free()
We use RCU to defer freeing of conntrack structures. In DOS situation, RCU might
accumulate about 10.000 elements per CPU in its internal queues. To get accurate
conntrack counts (at the expense of slightly more RAM used), we might consider
conntrack counter not taking into account "about to be freed elements, waiting
in RCU queues". We thus decrement it in nf_conntrack_free(), not in the RCU
callback.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Tested-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
David S. Miller [Mon, 23 Mar 2009 23:21:16 +0000 (16:21 -0700)]
ucc_geth: Fix merge error.
I left a merge failure unresolved, noticed by Stephen
Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Vorontsov [Thu, 19 Mar 2009 06:48:08 +0000 (06:48 +0000)]
fsl_pq_mdio: Use proper address translation
Currently the driver just read "reg" property for constructing MDIO
bus IDs, but this won't work when we'll start using "ranges = <>" in
the device tree, so this will pop up:
Freescale PowerQUICC MII Bus: probed
sysfs: duplicate filename 'mdio@520' can not be created
------------[ cut here ]------------
Badness at
c00cb6b8 [verbose debug info unavailable]
NIP:
c00cb6b8 LR:
c00cb6b8 CTR:
c001271c
REGS:
cf82fc10 TRAP: 0700 Not tainted (2.6.29-rc7-03702-g7ccd10f)
MSR:
00029032 <EE,ME,CE,IR,DR> CR:
42044022 XER:
20000000
TASK =
cf81fbd0[1] 'swapper' THREAD:
cf82e000
GPR00:
c00cb6b8 cf82fcc0 cf81fbd0 0000003b 00000e42 ffffffff 00004000 00000e42
GPR08:
c03cb0fc c03bfbdc 00000e42 c03cac50 22044022 1006a2bc 0ffcb000 00000000
GPR16:
0ffc04b0 0ffc5a40 00000000 0ffc79a8 0f7863a8 00000004 00000000 00000000
GPR24:
c033a6a8 d1014520 cf85e840 cf82fd08 cf87cf2c cf82fcd8 cf85dea8 ffffffef
NIP [
c00cb6b8] sysfs_add_one+0x4c/0x54
LR [
c00cb6b8] sysfs_add_one+0x4c/0x54
Call Trace:
[
cf82fcc0] [
c00cb6b8] sysfs_add_one+0x4c/0x54 (unreliable)
[
cf82fcd0] [
c00cbc18] create_dir+0x58/0xc0
[
cf82fd00] [
c00cbcc0] sysfs_create_dir+0x40/0x70
[
cf82fd20] [
c0159388] create_dir+0x28/0x78
[
cf82fd30] [
c0159824] kobject_add_internal+0x98/0x13c
[
cf82fd50] [
c0159e98] kobject_add+0x60/0x98
[
cf82fd80] [
c018a480] device_add+0x98/0x2ac
[
cf82fda0] [
c01a2380] mdiobus_register+0xbc/0x1c0
[
cf82fdc0] [
c019f31c] fsl_pq_mdio_probe+0x284/0x2a0
[
cf82fe00] [
c0223814] of_platform_device_probe+0x5c/0x84
...
This patch fixes the issue by translating the "reg" property to a full
address, and thus avoids the duplicate names.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 23 Mar 2009 21:42:09 +0000 (14:42 -0700)]
spider_net: Add missing .ndo_validate_addr
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 23 Mar 2009 21:29:24 +0000 (14:29 -0700)]
myri_sbus/sunbmac/sunlance/sunqe: Add missing net_device_ops entries.
Noticed by Stephen Hemminger.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 23 Mar 2009 20:35:04 +0000 (13:35 -0700)]
Merge branch 'master' of /linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/ucc_geth.c
David S. Miller [Mon, 23 Mar 2009 20:33:37 +0000 (13:33 -0700)]
sunqe: Convert to net_device_ops.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 23 Mar 2009 20:33:28 +0000 (13:33 -0700)]
sunlance: Convert to net_device_ops.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 23 Mar 2009 20:33:21 +0000 (13:33 -0700)]
sunbmac: Convert to net_device_ops.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 23 Mar 2009 20:33:11 +0000 (13:33 -0700)]
myri_sbus: Convert to net_device_ops.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Mon, 23 Mar 2009 12:21:06 +0000 (13:21 +0100)]
nefilter: nfnetlink: add nfnetlink_set_err and use it in ctnetlink
This patch adds nfnetlink_set_err() to propagate the error to netlink
broadcast listener in case of memory allocation errors in the
message building.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Eric Leblond [Mon, 23 Mar 2009 12:16:53 +0000 (13:16 +0100)]
netfilter: sysctl support of logger choice
This patchs adds support of modification of the used logger via sysctl.
It can be used to change the logger to module that can not use the bind
operation (ipt_LOG and ipt_ULOG). For this purpose, it creates a
directory /proc/sys/net/netfilter/nf_log which contains a file
per-protocol. The content of the file is the name current logger (NONE if
not set) and a logger can be setup by simply echoing its name to the file.
By echoing "NONE" to a /proc/sys/net/netfilter/nf_log/PROTO file, the
logger corresponding to this PROTO is set to NULL.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Huang Weiyi [Mon, 23 Mar 2009 08:18:58 +0000 (01:18 -0700)]
atl1c: remove duplicated #include
Remove duplicated #include in drivers/net/atl1c/atl1c.h.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 23 Mar 2009 08:03:04 +0000 (01:03 -0700)]
spider_net: Fix build.
Based upon a report by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
John Dykstra [Mon, 23 Mar 2009 04:49:57 +0000 (21:49 -0700)]
tcp: Discard segments that ack data not yet sent
Discard incoming packets whose ack field iincludes data not yet sent.
This is consistent with RFC 793 Section 3.9.
Change tcp_ack() to distinguish between too-small and too-large ack
field values. Keep segments with too-large ack fields out of the fast
path, and change slow path to discard them.
Reported-by: Oliver Zheng <mailinglists+netdev@oliverzheng.com>
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Vorontsov [Mon, 23 Mar 2009 04:30:52 +0000 (21:30 -0700)]
ucc_geth: Fix oops when using fixed-link support
commit
b1c4a9dddf09fe99b8f88252718ac5b357363dc4 ("ucc_geth: Change
uec phy id to the same format as gianfar's") introduced a regression
in the ucc_geth driver that causes this oops when fixed-link is used:
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc0151270
Oops: Kernel access of bad area, sig: 11 [#1]
TMCUTU
NIP:
c0151270 LR:
c0151270 CTR:
c0017760
REGS:
cf81fa60 TRAP: 0300 Not tainted (2.6.29-rc8)
MSR:
00009032 <EE,ME,IR,DR> CR:
24024042 XER:
20000000
DAR:
00000000, DSISR:
20000000
TASK =
cf81cba0[1] 'swapper' THREAD:
cf81e000
GPR00:
c0151270 cf81fb10 cf81cba0 00000000 c0272e20 c025f354 00001e80
cf86b08c
GPR08:
d1068200 cffffb74 06000000 d106c200 42024042 10085148 0fffd000
0ffc81a0
GPR16:
00000001 00000001 00000000 007ffeb0 00000000 0000c000 cf83f36c
cf83f000
GPR24:
00000030 cf83f360 cf81fb20 00000000 d106c200 20000000 00001e80
cf83f360
NIP [
c0151270] ucc_geth_open+0x330/0x1efc
LR [
c0151270] ucc_geth_open+0x330/0x1efc
Call Trace:
[
cf81fb10] [
c0151270] ucc_geth_open+0x330/0x1efc (unreliable)
[
cf81fba0] [
c0187638] dev_open+0xbc/0x12c
[
cf81fbc0] [
c0187e38] dev_change_flags+0x8c/0x1b0
This patch fixes the issue by removing offending (and somewhat
duplicate) code from init_phy() routine, and changes _probe()
function to use uec_mdio_bus_name().
Also, since we fully construct phy_bus_id in the _probe() routine,
we no longer need ->phy_address and ->mdio_bus fields in
ucc_geth_info structure.
I wish the patch would be a bit shorter, but it seems like the only
way to fix the issue in a sane way. Luckily, the patch has been
tested with real PHYs and fixed-link, so no further regressions
expected.
Reported-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Brownell [Mon, 23 Mar 2009 04:28:39 +0000 (21:28 -0700)]
dm9000: locking bugfix
This fixes a locking bug in the dm9000 driver. It calls
request_irq() without setting IRQF_DISABLED ... which is
correct for handlers that support IRQ sharing, since that
behavior is not guaranteed for shared IRQs. However, its
IRQ handler then wrongly assumes that IRQs are blocked.
So the fix just uses the right spinlock primitives in the
IRQ handler.
NOTE: this is a classic example of the type of bug which
lockdep currently masks by forcibly setting IRQF_DISABLED
on IRQ handlers that did not request that flag.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Mon, 23 Mar 2009 04:24:19 +0000 (21:24 -0700)]
bnx2x: Adding licensing to bnx2x_init_values.h
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Rothwell [Mon, 23 Mar 2009 04:22:48 +0000 (21:22 -0700)]
net: update dnet.c for bus_id removal
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:44 +0000 (19:36 +0000)]
netdev: expose net_device_ops compat as config option
Now that most network device drivers in (all but one in x86_64 allmodconfig)
support net_device_ops. Expose it as a configuration parameter. Still
need to address even older 32 bit drivers, and other arch before
compatiablity can be scheduled for removal in some future release.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:43 +0000 (19:36 +0000)]
hostap: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:42 +0000 (19:36 +0000)]
hostap: convert to internal net_device_stats
Use pre-existing net_device_stats in network_device struct.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:41 +0000 (19:36 +0000)]
ipw2200: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:40 +0000 (19:36 +0000)]
ipw2100: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:39 +0000 (19:36 +0000)]
ipw2x00: convert infrastructure for use by net_device_ops
Expose routines so drivers can hook. Only set ptrs in netdev
if using old compat code.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:38 +0000 (19:36 +0000)]
ipw2x00: convert to internal net_device_stats
Replace struct in ieee with current net_device_stats, so no longer
need get_stats hook
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:37 +0000 (19:36 +0000)]
libertas: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:36 +0000 (19:36 +0000)]
libertas: convert to internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:35 +0000 (19:36 +0000)]
prism54: convert to internal net_device_stats
Also, make ethtool_ops const as it should be, and get rid
of useless cast.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:34 +0000 (19:36 +0000)]
prism54: convert to net_device_ops
Also, make ethtool_ops const as it should be, and get rid
of useless cast.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:33 +0000 (19:36 +0000)]
mac80211_hwsim: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:32 +0000 (19:36 +0000)]
zd1201: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:31 +0000 (19:36 +0000)]
zd1201: convert to internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:30 +0000 (19:36 +0000)]
wl3501: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:29 +0000 (19:36 +0000)]
wl3501: convert to internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:28 +0000 (19:36 +0000)]
raylan: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:27 +0000 (19:36 +0000)]
atmel: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:26 +0000 (19:36 +0000)]
airo: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:25 +0000 (19:36 +0000)]
wavelan: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:24 +0000 (19:36 +0000)]
wavelan: convert to internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:23 +0000 (19:36 +0000)]
strip: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:22 +0000 (19:36 +0000)]
netwave: convert to net_device_ops
Also get rid of unneeded cast
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:21 +0000 (19:36 +0000)]
netwave: convert to internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:20 +0000 (19:36 +0000)]
sbni: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:19 +0000 (19:36 +0000)]
sbni: use internal net_device_stats
Convert to use existing net_device_stats.
This driver,
has bad style,
of using commas,
when brackets should be used...
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:18 +0000 (19:36 +0000)]
labether: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:17 +0000 (19:36 +0000)]
lapbether: convert to internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:16 +0000 (19:36 +0000)]
cycx: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:15 +0000 (19:36 +0000)]
dlci: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:14 +0000 (19:36 +0000)]
dlci: convert to internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:13 +0000 (19:36 +0000)]
x25_asy: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:12 +0000 (19:36 +0000)]
x25_asy: convert to internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:11 +0000 (19:36 +0000)]
axnet: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:10 +0000 (19:36 +0000)]
smc91c92: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:09 +0000 (19:36 +0000)]
smc91c92: convert to internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:08 +0000 (19:36 +0000)]
xirc2ps: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:07 +0000 (19:36 +0000)]
xir2cps: convert to internal net_device stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:06 +0000 (19:36 +0000)]
pcnet: convert driver to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:05 +0000 (19:36 +0000)]
pcmcia: convert nmclan driver to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:04 +0000 (19:36 +0000)]
pcmcia: convert fmvj18x driver to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:03 +0000 (19:36 +0000)]
pcmcia: convert fmvj18x driver to internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:02 +0000 (19:36 +0000)]
pcmcia: convert 3c574 to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:01 +0000 (19:36 +0000)]
pcmcia: convert 3c589 to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 20 Mar 2009 19:36:00 +0000 (19:36 +0000)]
usbnet: convert rndis driver to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / platform / kernel / linux-stable.git / log