Heiner Kallweit [Thu, 5 Aug 2021 19:08:22 +0000 (21:08 +0200)]
ethtool: return error from ethnl_ops_begin if dev is NULL
Julian reported that after
d43c65b05b84 Coverity complains about a
missing check whether dev is NULL in ethnl_ops_complete().
There doesn't seem to be any valid case where dev could be NULL when
calling ethnl_ops_begin(), therefore return an error if dev is NULL.
Fixes:
d43c65b05b84 ("ethtool: runtime-resume netdev parent in ethnl_ops_begin")
Reported-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leon Romanovsky [Thu, 5 Aug 2021 14:34:28 +0000 (17:34 +0300)]
netdevsim: Protect both reload_down and reload_up paths
Don't progress with adding and deleting ports as long as devlink
reload is running.
Fixes:
23809a726c0d ("netdevsim: Forbid devlink reload when adding or deleting ports")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 6 Aug 2021 09:26:55 +0000 (10:26 +0100)]
Merge branch 'cpsw-emac-skb_put_padto'
Grygorii Strashko says:
====================
net: ethernet: ti: cpsw/emac: switch to use skb_put_padto()
Now frame padding in TI TI CPSW/EMAC is implemented in a bit of entangled way as
frame SKB padded in drivers (without skb->len) while frame length fixed in CPDMA.
Things became even more confusing hence CPSW switcdev driver need to perform min
TX frame length correction in switch mode [1].
To avoid further confusion, make xmit path more clear and linear, and avoid
updating CPDMA configuration interface for min TX frame length correction
(which is not CPDMA job in general) this series switches TI CPSW/EMAC
drivers to skb_put_padto() instead of skb_padto() in their xmit path, so
skb->len also got updated properly and then removes TX frame length
fixup from CPDMA code.
[1] https://patchwork.kernel.org/project/netdevbpf/patch/
20210611132732.10690-1-grygorii.strashko@ti.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko [Thu, 5 Aug 2021 14:55:55 +0000 (17:55 +0300)]
net: ethernet: ti: davinci_cpdma: drop frame padding
Hence all users of davinci_cpdma switched to skb_put_padto() the frame
padding can be removed from it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko [Thu, 5 Aug 2021 14:55:54 +0000 (17:55 +0300)]
net: ethernet: ti: davinci_emac: switch to use skb_put_padto()
Use skb_put_padto() instead of skb_padto() so skb->len also got updated, as
preparation for further removing frame padding from cpdma.
It also makes xmit path more clear and linear.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko [Thu, 5 Aug 2021 14:55:53 +0000 (17:55 +0300)]
net: ethernet: ti: cpsw: switch to use skb_put_padto()
Use skb_put_padto() instead of skb_padto() so skb->len also got updated, as
preparation for further removing frame padding from cpdma.
It also makes xmit path more clear and linear.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 5 Aug 2021 21:59:40 +0000 (14:59 -0700)]
Merge git://git./linux/kernel/git/netdev/net
Build failure in drivers/net/wwan/mhi_wwan_mbim.c:
add missing parameter (0, assuming we don't want buffer pre-alloc).
Conflict in drivers/net/dsa/sja1105/sja1105_main.c between:
589918df9322 ("net: dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
0fac6aa098ed ("net: dsa: sja1105: delete the best_effort_vlan_filtering mode")
Follow the instructions from the commit message of the former commit
- removed the if conditions. When looking at commit
589918df9322 ("net:
dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
note that the mask_iotag fields get removed by the following patch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Thu, 5 Aug 2021 19:26:00 +0000 (12:26 -0700)]
Merge tag 'net-5.14-rc5' of git://git./linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from ipsec.
Current release - regressions:
- sched: taprio: fix init procedure to avoid inf loop when dumping
- sctp: move the active_key update after sh_keys is added
Current release - new code bugs:
- sparx5: fix build with old GCC & bitmask on 32-bit targets
Previous releases - regressions:
- xfrm: redo the PREEMPT_RT RCU vs hash_resize_mutex deadlock fix
- xfrm: fixes for the compat netlink attribute translator
- phy: micrel: Fix detection of ksz87xx switch
Previous releases - always broken:
- gro: set inner transport header offset in tcp/udp GRO hook to avoid
crashes when such packets reach GSO
- vsock: handle VIRTIO_VSOCK_OP_CREDIT_REQUEST, as required by spec
- dsa: sja1105: fix static FDB entries on SJA1105P/Q/R/S and SJA1110
- bridge: validate the NUD_PERMANENT bit when adding an extern_learn
FDB entry
- usb: lan78xx: don't modify phy_device state concurrently
- usb: pegasus: check for errors of IO routines"
* tag 'net-5.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (48 commits)
net: vxge: fix use-after-free in vxge_device_unregister
net: fec: fix use-after-free in fec_drv_remove
net: pegasus: fix uninit-value in get_interrupt_interval
net: ethernet: ti: am65-cpsw: fix crash in am65_cpsw_port_offload_fwd_mark_update()
bnx2x: fix an error code in bnx2x_nic_load()
net: wwan: iosm: fix recursive lock acquire in unregister
net: wwan: iosm: correct data protocol mask bit
net: wwan: iosm: endianness type correction
net: wwan: iosm: fix lkp buildbot warning
net: usb: lan78xx: don't modify phy_device state concurrently
docs: networking: netdevsim rules
net: usb: pegasus: Remove the changelog and DRIVER_VERSION.
net: usb: pegasus: Check the return value of get_geristers() and friends;
net/prestera: Fix devlink groups leakage in error flow
net: sched: fix lockdep_set_class() typo error for sch->seqlock
net: dsa: qca: ar9331: reorder MDIO write sequence
VSOCK: handle VIRTIO_VSOCK_OP_CREDIT_REQUEST
mptcp: drop unused rcu member in mptcp_pm_addr_entry
net: ipv6: fix returned variable type in ip6_skb_dst_mtu
nfp: update ethtool reporting of pauseframe control
...
Tetsuo Handa [Wed, 4 Aug 2021 10:26:56 +0000 (19:26 +0900)]
Bluetooth: defer cleanup of resources in hci_unregister_dev()
syzbot is hitting might_sleep() warning at hci_sock_dev_event() due to
calling lock_sock() with rw spinlock held [1].
It seems that history of this locking problem is a trial and error.
Commit
b40df5743ee8 ("[PATCH] bluetooth: fix socket locking in
hci_sock_dev_event()") in 2.6.21-rc4 changed bh_lock_sock() to
lock_sock() as an attempt to fix lockdep warning.
Then, commit
4ce61d1c7a8e ("[BLUETOOTH]: Fix locking in
hci_sock_dev_event().") in 2.6.22-rc2 changed lock_sock() to
local_bh_disable() + bh_lock_sock_nested() as an attempt to fix the
sleep in atomic context warning.
Then, commit
4b5dd696f81b ("Bluetooth: Remove local_bh_disable() from
hci_sock.c") in 3.3-rc1 removed local_bh_disable().
Then, commit
e305509e678b ("Bluetooth: use correct lock to prevent UAF
of hdev object") in 5.13-rc5 again changed bh_lock_sock_nested() to
lock_sock() as an attempt to fix CVE-2021-3573.
This difficulty comes from current implementation that
hci_sock_dev_event(HCI_DEV_UNREG) is responsible for dropping all
references from sockets because hci_unregister_dev() immediately
reclaims resources as soon as returning from
hci_sock_dev_event(HCI_DEV_UNREG).
But the history suggests that hci_sock_dev_event(HCI_DEV_UNREG) was not
doing what it should do.
Therefore, instead of trying to detach sockets from device, let's accept
not detaching sockets from device at hci_sock_dev_event(HCI_DEV_UNREG),
by moving actual cleanup of resources from hci_unregister_dev() to
hci_cleanup_dev() which is called by bt_host_release() when all
references to this unregistered device (which is a kobject) are gone.
Since hci_sock_dev_event(HCI_DEV_UNREG) no longer resets
hci_pi(sk)->hdev, we need to check whether this device was unregistered
and return an error based on HCI_UNREGISTER flag. There might be subtle
behavioral difference in "monitor the hdev" functionality; please report
if you found something went wrong due to this patch.
Link: https://syzkaller.appspot.com/bug?extid=a5df189917e79d5e59c9
Reported-by: syzbot <syzbot+a5df189917e79d5e59c9@syzkaller.appspotmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes:
e305509e678b ("Bluetooth: use correct lock to prevent UAF of hdev object")
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 5 Aug 2021 19:06:31 +0000 (12:06 -0700)]
Merge tag 'selinux-pr-
20210805' of git://git./linux/kernel/git/pcmoore/selinux
Pull selinux fix from Paul Moore:
"One small SELinux fix for a problem where an error code was not being
propagated back up to userspace when a bogus SELinux policy is loaded
into the kernel"
* tag 'selinux-pr-
20210805' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: correct the return value when loads initial sids
Linus Torvalds [Thu, 5 Aug 2021 19:00:00 +0000 (12:00 -0700)]
Merge branch 'for-v5.14' of git://git./linux/kernel/git/ebiederm/user-namespace
Pull ucounts fix from Eric Biederman:
"Fix a subtle locking versus reference counting bug in the ucount
changes, found by syzbot"
* 'for-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ucounts: Fix race condition between alloc_ucounts and put_ucounts
Linus Torvalds [Thu, 5 Aug 2021 18:53:34 +0000 (11:53 -0700)]
Merge tag 'trace-v5.14-rc4' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Various tracing fixes:
- Fix NULL pointer dereference caused by an error path
- Give histogram calculation fields a size, otherwise it breaks
synthetic creation based on them.
- Reject strings being used for number calculations.
- Fix recordmcount.pl warning on llvm building RISC-V allmodconfig
- Fix the draw_functrace.py script to handle the new trace output
- Fix warning of smp_processor_id() in preemptible code"
* tag 'trace-v5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Quiet smp_processor_id() use in preemptable warning in hwlat
scripts/tracing: fix the bug that can't parse raw_trace_func
scripts/recordmcount.pl: Remove check_objcopy() and $can_use_local
tracing: Reject string operand in the histogram expression
tracing / histogram: Give calculation hist_fields a size
tracing: Fix NULL pointer dereference in start_creating
Linus Torvalds [Thu, 5 Aug 2021 18:46:24 +0000 (11:46 -0700)]
Merge tag 's390-5.14-4' of git://git./linux/kernel/git/s390/linux
Pull s390 fixes from Heiko Carstens:
- fix zstd build for -march=z900 (undefined reference to __clzdi2)
- add missing .got.plts to vdso linker scripts to fix kpatch build
errors
- update defconfigs
* tag 's390-5.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: update defconfigs
s390/boot: fix zstd build for -march=z900
s390/vdso: add .got.plt in vdso linker script
Linus Torvalds [Thu, 5 Aug 2021 18:23:09 +0000 (11:23 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Mostly bugfixes; plus, support for XMM arguments to Hyper-V hypercalls
now obeys KVM_CAP_HYPERV_ENFORCE_CPUID.
Both the XMM arguments feature and KVM_CAP_HYPERV_ENFORCE_CPUID are
new in 5.14, and each did not know of the other"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86/mmu: Fix per-cpu counter corruption on 32-bit builds
KVM: selftests: fix hyperv_clock test
KVM: SVM: improve the code readability for ASID management
KVM: SVM: Fix off-by-one indexing when nullifying last used SEV VMCB
KVM: Do not leak memory for duplicate debugfs directories
KVM: selftests: Test access to XMM fast hypercalls
KVM: x86: hyper-v: Check if guest is allowed to use XMM registers for hypercall input
KVM: x86: Introduce trace_kvm_hv_hypercall_done()
KVM: x86: hyper-v: Check access to hypercall before reading XMM registers
KVM: x86: accept userspace interrupt only if no event is injected
Linus Torvalds [Thu, 5 Aug 2021 18:16:02 +0000 (11:16 -0700)]
Merge branch 'pcmcia-next' of git://git./linux/kernel/git/brodo/linux
Pull pcmcia fix from Dominik Brodowski:
"Zheyu Ma found and fixed a null pointer dereference bug in the device
driver for the i82092 card reader"
* 'pcmcia-next' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux:
pcmcia: i82092: fix a null pointer dereference bug
Alex Xu (Hello71) [Thu, 5 Aug 2021 14:40:47 +0000 (10:40 -0400)]
pipe: increase minimum default pipe size to 2 pages
This program always prints 4096 and hangs before the patch, and always
prints 8192 and exits successfully after:
int main()
{
int pipefd[2];
for (int i = 0; i < 1025; i++)
if (pipe(pipefd) == -1)
return 1;
size_t bufsz = fcntl(pipefd[1], F_GETPIPE_SZ);
printf("%zd\n", bufsz);
char *buf = calloc(bufsz, 1);
write(pipefd[1], buf, bufsz);
read(pipefd[0], buf, bufsz-1);
write(pipefd[1], buf, 1);
}
Note that you may need to increase your RLIMIT_NOFILE before running the
program.
Fixes:
759c01142a ("pipe: limit the per-user amount of pages allocated in pipes")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/lkml/1628086770.5rn8p04n6j.none@localhost/
Link: https://lore.kernel.org/lkml/1628127094.lxxn016tj7.none@localhost/
Signed-off-by: Alex Xu (Hello71) <alex_y_xu@yahoo.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jakub Kicinski [Thu, 5 Aug 2021 14:29:55 +0000 (07:29 -0700)]
Merge branch 'net-fix-use-after-free-bugs'
Pavel Skripkin says:
====================
net: fix use-after-free bugs
I've added new checker to smatch yesterday. It warns about using
netdev_priv() pointer after free_{netdev,candev}() call. I hope, it will
get into next smatch release.
Some of the reported bugs are fixed and upstreamed already, but Dan ran new
smatch with allmodconfig and found 2 more. Big thanks to Dan for doing it,
because I totally forgot to do it.
====================
Link: https://lore.kernel.org/r/cover.1628091954.git.paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pavel Skripkin [Wed, 4 Aug 2021 15:52:20 +0000 (18:52 +0300)]
net: vxge: fix use-after-free in vxge_device_unregister
Smatch says:
drivers/net/ethernet/neterion/vxge/vxge-main.c:3518 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3518 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3520 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3520 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
Since vdev pointer is netdev private data accessing it after free_netdev()
call can cause use-after-free bug. Fix it by moving free_netdev() call at
the end of the function
Fixes:
6cca200362b4 ("vxge: cleanup probe error paths")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pavel Skripkin [Wed, 4 Aug 2021 15:51:51 +0000 (18:51 +0300)]
net: fec: fix use-after-free in fec_drv_remove
Smatch says:
drivers/net/ethernet/freescale/fec_main.c:3994 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
drivers/net/ethernet/freescale/fec_main.c:3995 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
Since fep pointer is netdev private data, accessing it after free_netdev()
call can cause use-after-free bug. Fix it by moving free_netdev() call at
the end of the function
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes:
a31eda65ba21 ("net: fec: fix clock count mis-match")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pavel Skripkin [Wed, 4 Aug 2021 14:30:05 +0000 (17:30 +0300)]
net: pegasus: fix uninit-value in get_interrupt_interval
Syzbot reported uninit value pegasus_probe(). The problem was in missing
error handling.
get_interrupt_interval() internally calls read_eprom_word() which can
fail in some cases. For example: failed to receive usb control message.
These cases should be handled to prevent uninit value bug, since
read_eprom_word() will not initialize passed stack variable in case of
internal failure.
Fail log:
BUG: KMSAN: uninit-value in get_interrupt_interval drivers/net/usb/pegasus.c:746 [inline]
BUG: KMSAN: uninit-value in pegasus_probe+0x10e7/0x4080 drivers/net/usb/pegasus.c:1152
CPU: 1 PID: 825 Comm: kworker/1:1 Not tainted 5.12.0-rc6-syzkaller #0
...
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x24c/0x2e0 lib/dump_stack.c:120
kmsan_report+0xfb/0x1e0 mm/kmsan/kmsan_report.c:118
__msan_warning+0x5c/0xa0 mm/kmsan/kmsan_instr.c:197
get_interrupt_interval drivers/net/usb/pegasus.c:746 [inline]
pegasus_probe+0x10e7/0x4080 drivers/net/usb/pegasus.c:1152
....
Local variable ----data.i@pegasus_probe created at:
get_interrupt_interval drivers/net/usb/pegasus.c:1151 [inline]
pegasus_probe+0xe57/0x4080 drivers/net/usb/pegasus.c:1152
get_interrupt_interval drivers/net/usb/pegasus.c:1151 [inline]
pegasus_probe+0xe57/0x4080 drivers/net/usb/pegasus.c:1152
Reported-and-tested-by: syzbot+02c9f70f3afae308464a@syzkaller.appspotmail.com
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20210804143005.439-1-paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Steven Rostedt (VMware) [Wed, 4 Aug 2021 18:18:48 +0000 (14:18 -0400)]
tracing: Quiet smp_processor_id() use in preemptable warning in hwlat
The hardware latency detector (hwlat) has a mode that it runs one thread
across CPUs. The logic to move from the currently running CPU to the next
one in the list does a smp_processor_id() to find where it currently is.
Unfortunately, it's done with preemption enabled, and this triggers a
warning for using smp_processor_id() in a preempt enabled section.
As it is only using smp_processor_id() to get information on where it
currently is in order to simply move it to the next CPU, it doesn't really
care if it got moved in the mean time. It will simply balance out later if
such a case arises.
Switch smp_processor_id() to raw_smp_processor_id() to quiet that warning.
Link: https://lkml.kernel.org/r/20210804141848.79edadc0@oasis.local.home
Acked-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Fixes:
8fa826b7344d ("trace/hwlat: Implement the mode config option")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Grygorii Strashko [Thu, 5 Aug 2021 10:14:09 +0000 (13:14 +0300)]
net: ethernet: ti: am65-cpsw: fix crash in am65_cpsw_port_offload_fwd_mark_update()
The am65_cpsw_port_offload_fwd_mark_update() causes NULL exception crash
when there is at least one disabled port and any other port added to the
bridge first time.
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000858
pc : am65_cpsw_port_offload_fwd_mark_update+0x54/0x68
lr : am65_cpsw_netdevice_event+0x8c/0xf0
Call trace:
am65_cpsw_port_offload_fwd_mark_update+0x54/0x68
notifier_call_chain+0x54/0x98
raw_notifier_call_chain+0x14/0x20
call_netdevice_notifiers_info+0x34/0x78
__netdev_upper_dev_link+0x1c8/0x290
netdev_master_upper_dev_link+0x1c/0x28
br_add_if+0x3f0/0x6d0 [bridge]
Fix it by adding proper check for port->ndev != NULL.
Fixes:
2934db9bcb30 ("net: ti: am65-cpsw-nuss: Add netdevice notifiers")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 5 Aug 2021 10:38:26 +0000 (13:38 +0300)]
bnx2x: fix an error code in bnx2x_nic_load()
Set the error code if bnx2x_alloc_fw_stats_mem() fails. The current
code returns success.
Fixes:
ad5afc89365e ("bnx2x: Separate VF and PF logic")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leon Romanovsky [Thu, 5 Aug 2021 11:02:45 +0000 (14:02 +0300)]
netdevsim: Forbid devlink reload when adding or deleting ports
In order to remove complexity in devlink core related to
devlink_reload_enable/disable, let's rewrite new_port/del_port
logic to rely on internal to netdevsim lcok.
We should protect only reload_down flow because it destroys nsim_dev,
which is needed for nsim_dev_port_add/nsim_dev_port_del to hold
port_list_lock.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 5 Aug 2021 11:36:12 +0000 (14:36 +0300)]
net: dsa: tag_sja1105: optionally build as module when switch driver is module if PTP is enabled
TX timestamps are sent by SJA1110 as Ethernet packets containing
metadata, so they are received by the tagging driver but must be
processed by the switch driver - the one that is stateful since it
keeps the TX timestamp queue.
This means that there is an sja1110_process_meta_tstamp() symbol
exported by the switch driver which is called by the tagging driver.
There is a shim definition for that function when the switch driver is
not compiled, which does nothing, but that shim is not effective when
the tagging protocol driver is built-in and the switch driver is a
module, because built-in code cannot call symbols exported by modules.
So add an optional dependency between the tagger and the switch driver,
if PTP support is enabled in the switch driver. If PTP is not enabled,
sja1110_process_meta_tstamp() will translate into the shim "do nothing
with these meta frames" function.
Fixes:
566b18c8b752 ("net: dsa: sja1105: implement TX timestamping for SJA1110")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yajun Deng [Thu, 5 Aug 2021 11:54:34 +0000 (19:54 +0800)]
netdevice: add the case if dev is NULL
Add the case if dev is NULL in dev_{put, hold}, so the caller doesn't
need to care whether dev is NULL or not.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yajun Deng [Thu, 5 Aug 2021 11:55:27 +0000 (19:55 +0800)]
net: Remove redundant if statements
The 'if (dev)' statement already move into dev_{put , hold}, so remove
redundant if statements.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 5 Aug 2021 12:23:29 +0000 (13:23 +0100)]
Revert "wwan: mhi: Fix build."
This reverts commit
ab996c420508761f3313c15c5f72d06ca7dc1a5b.
Only aplicable when net is merged into net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 5 Aug 2021 12:14:09 +0000 (13:14 +0100)]
Merge branch 'GRO-Toeplitz-selftests'
Coco Li says:
====================
GRO and Toeplitz hash selftests
This patch contains two selftests in net, as well as respective
scripts to run the tests on a single machine in loopback mode.
GRO: tests the Linux kernel GRO behavior
Toeplitz: tests the toeplitz hash implementation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Coco Li [Thu, 5 Aug 2021 07:36:41 +0000 (07:36 +0000)]
selftests/net: toeplitz test
To verify that this hash implements the Toeplitz hash function.
Additionally, provide a script toeplitz.sh to run the test in loopback mode
on a networking device of choice (see setup_loopback.sh). Since the
script modifies the NIC setup, it will not be run by selftests
automatically.
Tested:
./toeplitz.sh -i eth0 -irq_prefix <eth0_pattern> -t -6
carrier ready
rxq 0: cpu 14
rxq 1: cpu 20
rxq 2: cpu 17
rxq 3: cpu 23
cpu 14: rx_hash 0x69103ebc [saddr fda8::2 daddr fda8::1 sport 58938 dport 8000] OK rxq 0 (cpu 14)
...
cpu 20: rx_hash 0x257118b9 [saddr fda8::2 daddr fda8::1 sport 59258 dport 8000] OK rxq 1 (cpu 20)
count: pass=111 nohash=0 fail=0
Test Succeeded!
Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coco Li [Thu, 5 Aug 2021 07:36:40 +0000 (07:36 +0000)]
selftests/net: GRO coalesce test
Implement a GRO testsuite that expects Linux kernel GRO behavior.
All tests pass with the kernel software GRO stack. Run against a device
with hardware GRO to verify that it matches the software stack.
gro.c generates packets and sends them out through a packet socket. The
receiver in gro.c (run separately) receives the packets on a packet
socket, filters them by destination ports using BPF and checks the
packet geometry to see whether GRO was applied.
gro.sh provides a wrapper to run the gro.c in NIC loopback mode.
It is not included in continuous testing because it modifies network
configuration around a physical NIC: gro.sh sets the NIC in loopback
mode, creates macvlan devices on the physical device in separate
namespaces, and sends traffic generated by gro.c between the two
namespaces to observe coalescing behavior.
GRO coalescing is time sensitive.
Some tests may prove flaky on some hardware.
Note that this test suite tests for software GRO unless hardware GRO is
enabled (ethtool -K $DEV rx-gro-hw on).
To test, run ./gro.sh.
The wrapper will output success or failed test names, and generate
log.txt and stderr.
Sample log.txt result:
...
pure data packet of same size: Test succeeded
large data packets followed by a smaller one: Test succeeded
small data packets followed by a larger one: Test succeeded
...
Sample stderr result:
...
carrier ready
running test ipv4 data
Expected {200 }, Total 1 packets
Received {200 }, Total 1 packets.
...
Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 5 Aug 2021 12:10:50 +0000 (13:10 +0100)]
wwan: mhi: Fix build.
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gustavo A. R. Silva [Wed, 4 Aug 2021 21:43:52 +0000 (16:43 -0500)]
net/ipv6/mcast: Use struct_size() helper
Replace IP6_SFLSIZE() with struct_size() helper in order to avoid any
potential type mistakes or integer overflows that, in the worst
scenario, could lead to heap overflows.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gustavo A. R. Silva [Wed, 4 Aug 2021 21:18:50 +0000 (16:18 -0500)]
net/ipv4/igmp: Use struct_size() helper
Replace IP_SFLSIZE() with struct_size() helper in order to avoid any
potential type mistakes or integer overflows that, in the worst
scenario, could lead to heap overflows.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gustavo A. R. Silva [Wed, 4 Aug 2021 20:45:36 +0000 (15:45 -0500)]
net/ipv4/ipv6: Replace one-element arraya with flexible-array members
There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
Use an anonymous union with a couple of anonymous structs in order to
keep userspace unchanged and refactor the related code accordingly:
$ pahole -C group_filter net/ipv4/ip_sockglue.o
struct group_filter {
union {
struct {
__u32 gf_interface_aux; /* 0 4 */
/* XXX 4 bytes hole, try to pack */
struct __kernel_sockaddr_storage gf_group_aux; /* 8 128 */
/* --- cacheline 2 boundary (128 bytes) was 8 bytes ago --- */
__u32 gf_fmode_aux; /* 136 4 */
__u32 gf_numsrc_aux; /* 140 4 */
struct __kernel_sockaddr_storage gf_slist[1]; /* 144 128 */
}; /* 0 272 */
struct {
__u32 gf_interface; /* 0 4 */
/* XXX 4 bytes hole, try to pack */
struct __kernel_sockaddr_storage gf_group; /* 8 128 */
/* --- cacheline 2 boundary (128 bytes) was 8 bytes ago --- */
__u32 gf_fmode; /* 136 4 */
__u32 gf_numsrc; /* 140 4 */
struct __kernel_sockaddr_storage gf_slist_flex[0]; /* 144 0 */
}; /* 0 144 */
}; /* 0 272 */
/* size: 272, cachelines: 5, members: 1 */
/* last cacheline: 16 bytes */
};
$ pahole -C compat_group_filter net/ipv4/ip_sockglue.o
struct compat_group_filter {
union {
struct {
__u32 gf_interface_aux; /* 0 4 */
struct __kernel_sockaddr_storage gf_group_aux __attribute__((__aligned__(4))); /* 4 128 */
/* --- cacheline 2 boundary (128 bytes) was 4 bytes ago --- */
__u32 gf_fmode_aux; /* 132 4 */
__u32 gf_numsrc_aux; /* 136 4 */
struct __kernel_sockaddr_storage gf_slist[1] __attribute__((__aligned__(4))); /* 140 128 */
} __attribute__((__packed__)) __attribute__((__aligned__(4))); /* 0 268 */
struct {
__u32 gf_interface; /* 0 4 */
struct __kernel_sockaddr_storage gf_group __attribute__((__aligned__(4))); /* 4 128 */
/* --- cacheline 2 boundary (128 bytes) was 4 bytes ago --- */
__u32 gf_fmode; /* 132 4 */
__u32 gf_numsrc; /* 136 4 */
struct __kernel_sockaddr_storage gf_slist_flex[0] __attribute__((__aligned__(4))); /* 140 0 */
} __attribute__((__packed__)) __attribute__((__aligned__(4))); /* 0 140 */
} __attribute__((__aligned__(1))); /* 0 268 */
/* size: 268, cachelines: 5, members: 1 */
/* forced alignments: 1 */
/* last cacheline: 12 bytes */
} __attribute__((__packed__));
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.10/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/109
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 5 Aug 2021 10:36:59 +0000 (11:36 +0100)]
Merge branch 'bridge-ioctl-fixes'
Nikolay Aleksandrov says:
====================
net: bridge: fix recent ioctl changes
These are three fixes for the recent bridge removal of ndo_do_ioctl
done by commit
ad2f99aedf8f ("net: bridge: move bridge ioctls out of
.ndo_do_ioctl"). Patch 01 fixes a deadlock of the new bridge ioctl
hook lock and rtnl by taking a netdev reference and always taking the
bridge ioctl lock first then rtnl from within the bridge hook.
Patch 02 fixes old_deviceless() bridge calls device name argument, and
patch 03 checks in dev_ifsioc()'s SIOCBRADD/DELIF cases if the netdevice is
actually a bridge before interpreting its private ptr as net_bridge.
Patch 01 was tested by running old bridge-utils commands with lockdep
enabled. Patch 02 was tested again by using bridge-utils and using the
respective ioctl calls on a "up" bridge device. Patch 03 was tested by
using the addif ioctl on a non-bridge device (e.g. loopback).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Thu, 5 Aug 2021 08:29:03 +0000 (11:29 +0300)]
net: core: don't call SIOCBRADD/DELIF for non-bridge devices
Commit
ad2f99aedf8f ("net: bridge: move bridge ioctls out of .ndo_do_ioctl")
changed SIOCBRADD/DELIF to use bridge's ioctl hook (br_ioctl_hook)
without checking if the target netdevice is actually a bridge which can
cause crashes and generally interpreting other devices' private pointers
as net_bridge pointers.
Crash example (lo - loopback):
$ brctl addif lo ens16
BUG: kernel NULL pointer dereference, address:
000000000000059898
#PF: supervisor read access in kernel modede
#PF: error_code(0x0000) - not-present pagege
PGD 0 P4D 0 ^Ac
Oops: 0000 [#1] SMP NOPTI
CPU: 2 PID: 1376 Comm: brctl Kdump: loaded Tainted: G W 5.14.0-rc3+ #405
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/01/2014
RIP: 0010:add_del_if+0x1f/0x7c [bridge]
Code: 80 bf 1b a0 41 5c e9 c0 3c 03 e1 0f 1f 44 00 00 41 55 41 54 41 89 f4 be 0c 00 00 00 55 48 89 fd 53 48 8b 87 88 00 00 00 89 d3 <4c> 8b a8 98 05 00 00 49 8b bd d0 00 00 00 e8 17 d7 f3 e0 84 c0 74
RSP: 0018:
ffff888109d97cb0 EFLAGS:
00010202^Ac
RAX:
0000000000000000 RBX:
0000000000000000 RCX:
0000000000000000
RDX:
0000000000000000 RSI:
000000000000000c RDI:
ffff888101239bc0
RBP:
ffff888101239bc0 R08:
0000000000000001 R09:
0000000000000000
R10:
ffff888109d97cd8 R11:
00000000000000a3 R12:
0000000000000012
R13:
0000000000000000 R14:
ffff888101239bc0 R15:
ffff888109d97e10
FS:
00007fc1e365b540(0000) GS:
ffff88822be80000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000000000598 CR3:
0000000106506000 CR4:
00000000000006e0
Call Trace:
br_ioctl_stub+0x7c/0x441 [bridge]
br_ioctl_call+0x6d/0x8a
dev_ifsioc+0x325/0x4e8
dev_ioctl+0x46b/0x4e1
sock_do_ioctl+0x7b/0xad
sock_ioctl+0x2de/0x2f2
vfs_ioctl+0x1e/0x2b
__do_sys_ioctl+0x63/0x86
do_syscall_64+0xcb/0xf2
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7fc1e3589427
Code: 00 00 90 48 8b 05 69 aa 0c 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 39 aa 0c 00 f7 d8 64 89 01 48
RSP: 002b:
00007ffc8d501d38 EFLAGS:
00000202 ORIG_RAX:
000000000000001010
RAX:
ffffffffffffffda RBX:
0000000000000012 RCX:
00007fc1e3589427
RDX:
00007ffc8d501d60 RSI:
00000000000089a3 RDI:
0000000000000003
RBP:
00007ffc8d501d60 R08:
0000000000000000 R09:
fefefeff77686d74
R10:
fffffffffffff8f9 R11:
0000000000000202 R12:
00007ffc8d502e06
R13:
00007ffc8d502e06 R14:
0000000000000000 R15:
0000000000000000
Modules linked in: bridge stp llc bonding ipv6 virtio_net [last unloaded: llc]^Ac
CR2:
0000000000000598
Reported-by: syzbot+79f4a8692e267bdb7227@syzkaller.appspotmail.com
Fixes:
ad2f99aedf8f ("net: bridge: move bridge ioctls out of .ndo_do_ioctl")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Thu, 5 Aug 2021 08:29:02 +0000 (11:29 +0300)]
net: bridge: fix ioctl old_deviceless bridge argument
Commit
ad2f99aedf8f ("net: bridge: move bridge ioctls out of .ndo_do_ioctl")
changed the source of the argument copy in bridge's old_deviceless() from
args[1] (user ptr to device name) to uarg (ptr to ioctl arguments) causing
wrong device name to be used.
Example (broken, bridge exists but is up):
$ brctl delbr bridge
bridge bridge doesn't exist; can't delete it
Example (working):
$ brctl delbr bridge
bridge bridge is still up; can't delete it
Fixes:
ad2f99aedf8f ("net: bridge: move bridge ioctls out of .ndo_do_ioctl")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Thu, 5 Aug 2021 08:29:01 +0000 (11:29 +0300)]
net: bridge: fix ioctl locking
Before commit
ad2f99aedf8f ("net: bridge: move bridge ioctls out of
.ndo_do_ioctl") the bridge ioctl calls were divided in two parts:
one was deviceless called by sock_ioctl and didn't expect rtnl to be held,
the other was with a device called by dev_ifsioc() and expected rtnl to be
held. After the commit above they were united in a single ioctl stub, but
it didn't take care of the locking expectations.
For sock_ioctl now we acquire (1) br_ioctl_mutex, (2) rtnl
and for dev_ifsioc we acquire (1) rtnl, (2) br_ioctl_mutex
The fix is to get a refcnt on the netdev for dev_ifsioc calls and drop rtnl
then to reacquire it in the bridge ioctl stub after br_ioctl_mutex has
been acquired. That will avoid playing locking games and make the rules
straight-forward: we always take br_ioctl_mutex first, and then rtnl.
Reported-by: syzbot+34fe5894623c4ab1b379@syzkaller.appspotmail.com
Fixes:
ad2f99aedf8f ("net: bridge: move bridge ioctls out of .ndo_do_ioctl")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gustavo A. R. Silva [Wed, 4 Aug 2021 18:23:25 +0000 (13:23 -0500)]
net/ipv4: Revert use of struct_size() helper
Revert the use of structr_size() and stay with IP_MSFILTER_SIZE() for
now, as in this case, the size of struct ip_msfilter didn't change with
the addition of the flexible array imsf_slist_flex[]. So, if we use
struct_size() we will be allocating and calculating the size of
struct ip_msfilter with one too many items for imsf_slist_flex[].
We might use struct_size() in the future, but for now let's stay
with IP_MSFILTER_SIZE().
Fixes:
2d3e5caf96b9 ("net/ipv4: Replace one-element array with flexible-array member")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 4 Aug 2021 19:07:00 +0000 (21:07 +0200)]
net: fix GRO skb truesize update
commit
5e10da5385d2 ("skbuff: allow 'slow_gro' for skb carring sock
reference") introduces a serious regression at the GRO layer setting
the wrong truesize for stolen-head skbs.
Restore the correct truesize: SKB_DATA_ALIGN(...) instead of
SKB_TRUESIZE(...)
Reported-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Fixes:
5e10da5385d2 ("skbuff: allow 'slow_gro' for skb carring sock reference")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 5 Aug 2021 10:28:56 +0000 (11:28 +0100)]
Merge branch 'eean-iosm-fixes'
M Chetan Kumar says:
====================
net: wwan: iosm: fixes
This patch series contains IOSM Driver fixes. Below is the patch
series breakdown.
PATCH1:
* Correct the td buffer type casting & format specifier to fix lkp buildbot
warning.
PATCH2:
* Endianness type correction for nr_of_bytes. This field is exchanged
as part of host-device protocol communication.
PATCH3:
* Correct ul/dl data protocol mask bit to know which protocol capability
does device implement.
PATCH4:
* Calling unregister_netdevice() inside wwan del link is trying to
acquire the held lock in ndo_stop_cb(). Instead, queue net dev to
be unregistered later.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
M Chetan Kumar [Wed, 4 Aug 2021 16:09:52 +0000 (21:39 +0530)]
net: wwan: iosm: fix recursive lock acquire in unregister
Calling unregister_netdevice() inside wwan del link is trying to
acquire the held lock in ndo_stop_cb(). Instead, queue net dev to
be unregistered later.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
M Chetan Kumar [Wed, 4 Aug 2021 16:09:51 +0000 (21:39 +0530)]
net: wwan: iosm: correct data protocol mask bit
Correct ul/dl data protocol mask bit to know which protocol capability
does device implement.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
M Chetan Kumar [Wed, 4 Aug 2021 16:09:50 +0000 (21:39 +0530)]
net: wwan: iosm: endianness type correction
Endianness type correction for nr_of_bytes. This field is exchanged
as part of host-device protocol communication.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
M Chetan Kumar [Wed, 4 Aug 2021 16:09:49 +0000 (21:39 +0530)]
net: wwan: iosm: fix lkp buildbot warning
Correct td buffer type casting & format specifier to fix lkp buildbot
warning.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 5 Aug 2021 10:27:05 +0000 (11:27 +0100)]
Merge branch 'ipa-runtime-pm'
Alex Elder says:
====================
net: ipa: more work toward runtime PM
The first two patches in this series are basically bug fixes, but in
practice I don't think we've seen the problems they might cause.
The third patch moves clock and interconnect related error messages
around a bit, reporting better information and doing so in the
functions where they are enabled or disabled (rather than those
functions' callers).
The last three patches move power-related code into "ipa_clock.c",
as a step toward generalizing the purpose of that source file.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Wed, 4 Aug 2021 15:36:26 +0000 (10:36 -0500)]
net: ipa: move IPA flags field
The ipa->flags field is only ever used in "ipa_clock.c", related to
suspend/resume activity.
Move the definition of the ipa_flag enumerated type to "ipa_clock.c".
And move the flags field from the ipa structure and to the ipa_clock
structure. Rename the type and its values to include "power" or
"POWER" in the name.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Wed, 4 Aug 2021 15:36:25 +0000 (10:36 -0500)]
net: ipa: move ipa_suspend_handler()
Move ipa_suspend_handler() into "ipa_clock.c" from "ipa_main.c", to
group with the reset of the suspend/resume code. This IPA interrupt
is triggered if an IPA RX endpoint is suspended but has a packet to
be delivered.
Introduce ipa_power_setup() and ipa_power_teardown() to add and
remove the handler for the IPA SUSPEND interrupt at the same place
as before, while allowing the handler to remain private.
The "power" naming convention will be adopted elsewhere in this
file as well (soon).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Wed, 4 Aug 2021 15:36:24 +0000 (10:36 -0500)]
net: ipa: move IPA power operations to ipa_clock.c
Move ipa_suspend() and ipa_resume(), as well as the definition of
the ipa_pm_ops structure into "ipa_clock.c". Make ipa_pm_ops public
and declare it as extern in "ipa_clock.h".
This is part of centralizing IPA power management functionality into
"ipa_clock.c" (the file will eventually get a name change).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Wed, 4 Aug 2021 15:36:23 +0000 (10:36 -0500)]
net: ipa: improve IPA clock error messages
Rearrange messages reported when errors occur in the IPA clock code,
so that the specific interconnect is identified when an error occurs
enabling or disabling it, or the core clock is indicated when an
error occurs enabling it.
Have ipa_interconnect_disable() return zero or the negative error
value returned by the first interconnect that produced an error
when disabled. For now, the callers ignore the returned value.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Wed, 4 Aug 2021 15:36:22 +0000 (10:36 -0500)]
net: ipa: reorder netdev pointer assignments
Assign the ipa->modem_netdev and endpoint->netdev pointers *before*
registering the network device. As soon as the device is
registered it can be opened, and by that time we'll want those
pointers valid.
Similarly, don't make those pointers NULL until *after* the modem
network device is unregistered in ipa_modem_stop().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Wed, 4 Aug 2021 15:36:21 +0000 (10:36 -0500)]
net: ipa: don't suspend/resume modem if not up
The modem network device is set up by ipa_modem_start(). But its
TX queue is not actually started and endpoints enabled until it is
opened.
So avoid stopping the modem network device TX queue and disabling
endpoints on suspend or stop unless the netdev is marked UP. And
skip attempting to resume unless it is UP.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 5 Aug 2021 10:05:48 +0000 (11:05 +0100)]
Merge branch 'sja1105-H'
Vladimir Oltean says:
====================
NXP SJA1105 driver support for "H" switch topologies
Changes in v3:
Preserve the behavior of dsa_tree_setup_default_cpu() which is to pick
the first CPU port and not the last.
Changes in v2:
Send as non-RFC, drop the patches for discarding DSA-tagged packets on
user ports and DSA-untagged packets on DSA and CPU ports for now.
NXP builds boards like the Bluebox 3 where there are multiple SJA1110
switches connected to an LX2160A, but they are also connected to each
other. I call this topology an "H" tree because of the lateral
connection between switches. A piece extracted from a non-upstream
device tree looks like this:
&spi_bridge {
/* SW1 */
ethernet-switch@0 {
compatible = "nxp,sja1110a";
reg = <0>;
dsa,member = <0 0>;
ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
/* SW1_P1 */
port@1 {
reg = <1>;
label = "con_2x20";
phy-mode = "sgmii";
fixed-link {
speed = <1000>;
full-duplex;
};
};
port@2 {
reg = <2>;
ethernet = <&dpmac17>;
phy-mode = "rgmii-id";
fixed-link {
speed = <1000>;
full-duplex;
};
};
port@3 {
reg = <3>;
label = "1ge_p1";
phy-mode = "rgmii-id";
phy-handle = <&sw1_mii3_phy>;
};
sw1p4: port@4 {
reg = <4>;
link = <&sw2p1>;
phy-mode = "sgmii";
fixed-link {
speed = <1000>;
full-duplex;
};
};
port@5 {
reg = <5>;
label = "trx1";
phy-mode = "internal";
phy-handle = <&sw1_port5_base_t1_phy>;
};
port@6 {
reg = <6>;
label = "trx2";
phy-mode = "internal";
phy-handle = <&sw1_port6_base_t1_phy>;
};
port@7 {
reg = <7>;
label = "trx3";
phy-mode = "internal";
phy-handle = <&sw1_port7_base_t1_phy>;
};
port@8 {
reg = <8>;
label = "trx4";
phy-mode = "internal";
phy-handle = <&sw1_port8_base_t1_phy>;
};
port@9 {
reg = <9>;
label = "trx5";
phy-mode = "internal";
phy-handle = <&sw1_port9_base_t1_phy>;
};
port@a {
reg = <10>;
label = "trx6";
phy-mode = "internal";
phy-handle = <&sw1_port10_base_t1_phy>;
};
};
};
/* SW2 */
ethernet-switch@2 {
compatible = "nxp,sja1110a";
reg = <2>;
dsa,member = <0 1>;
ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
sw2p1: port@1 {
reg = <1>;
link = <&sw1p4>;
phy-mode = "sgmii";
fixed-link {
speed = <1000>;
full-duplex;
};
};
port@2 {
reg = <2>;
ethernet = <&dpmac18>;
phy-mode = "rgmii-id";
fixed-link {
speed = <1000>;
full-duplex;
};
};
port@3 {
reg = <3>;
label = "1ge_p2";
phy-mode = "rgmii-id";
phy-handle = <&sw2_mii3_phy>;
};
port@4 {
reg = <4>;
label = "to_sw3";
phy-mode = "2500base-x";
fixed-link {
speed = <2500>;
full-duplex;
};
};
port@5 {
reg = <5>;
label = "trx7";
phy-mode = "internal";
phy-handle = <&sw2_port5_base_t1_phy>;
};
port@6 {
reg = <6>;
label = "trx8";
phy-mode = "internal";
phy-handle = <&sw2_port6_base_t1_phy>;
};
port@7 {
reg = <7>;
label = "trx9";
phy-mode = "internal";
phy-handle = <&sw2_port7_base_t1_phy>;
};
port@8 {
reg = <8>;
label = "trx10";
phy-mode = "internal";
phy-handle = <&sw2_port8_base_t1_phy>;
};
port@9 {
reg = <9>;
label = "trx11";
phy-mode = "internal";
phy-handle = <&sw2_port9_base_t1_phy>;
};
port@a {
reg = <10>;
label = "trx12";
phy-mode = "internal";
phy-handle = <&sw2_port10_base_t1_phy>;
};
};
};
};
Basically it is a single DSA tree with 2 "ethernet" properties, i.e. a
multi-CPU-port system. There is also a DSA link between the switches,
but it is not a daisy chain topology, i.e. there is no "upstream" and
"downstream" switch, the DSA link is only to be used for the bridge data
plane (autonomous forwarding between switches, between the RJ-45 ports
and the automotive Ethernet ports), otherwise all traffic that should
reach the host should do so through the dedicated CPU port of the switch.
Of course, plain forwarding in this topology is bound to create packet
loops. I have thought long and hard about strategies to cut forwarding
in such a way as to prevent loops but also not impede normal operation
of the network on such a system, and I believe I have found a solution
that does work as expected. This relies heavily on DSA's recent ability
to perform RX filtering towards the host by installing MAC addresses as
static FDB entries. Since we have 2 distinct DSA masters, we have 2
distinct MAC addresses, and if the bridge is configured to have its own
MAC address that makes it 3 distinct MAC addresses. The bridge core,
plus the switchdev_handle_fdb_add_to_device() extension, handle each MAC
address by replicating it to each port of the DSA switch tree. So the
end result is that both switch 1 and switch 2 will have static FDB
entries towards their respective CPU ports for the 3 MAC addresses
corresponding to the DSA masters and to the bridge net device (and of
course, towards any station learned on a foreign interface).
So I think the basic design works, and it is basically just as fragile
as any other multi-CPU-port system is bound to be in terms of reliance
on static FDB entries towards the host (if hardware address learning on
the CPU port is to be used, MAC addresses would randomly bounce between
one CPU port and the other otherwise). In fact, I think it is even
better to start DSA's support of multi-CPU-port systems with something
small like the NXP Bluebox 3, because we allow some time for the code
paths like dsa_switch_host_address_match(), which were specifically
designed for it, to break in, and this board needs no user space
configuration of CPU ports, like static assignments between user and CPU
ports, or bonding between the CPU ports/DSA masters.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Wed, 4 Aug 2021 13:54:36 +0000 (16:54 +0300)]
net: dsa: sja1105: enable address learning on cascade ports
Right now, address learning is disabled on DSA ports, which means that a
packet received over a DSA port from a cross-chip switch will be flooded
to unrelated ports.
It is desirable to eliminate that, but for that we need a breakdown of
the possibilities for the sja1105 driver. A DSA port can be:
- a downstream-facing cascade port. This is simple because it will
always receive packets from a downstream switch, and there should be
no other route to reach that downstream switch in the first place,
which means it should be safe to learn that MAC address towards that
switch.
- an upstream-facing cascade port. This receives packets either:
* autonomously forwarded by an upstream switch (and therefore these
packets belong to the data plane of a bridge, so address learning
should be ok), or
* injected from the CPU. This deserves further discussion, as normally,
an upstream-facing cascade port is no different than the CPU port
itself. But with "H" topologies (a DSA link towards a switch that
has its own CPU port), these are more "laterally-facing" cascade
ports than they are "upstream-facing". Here, there is a risk that
the port might learn the host addresses on the wrong port (on the
DSA port instead of on its own CPU port), but this is solved by
DSA's RX filtering infrastructure, which installs the host addresses
as static FDB entries on the CPU port of all switches in a "H" tree.
So even if there will be an attempt from the switch to migrate the
FDB entry from the CPU port to the laterally-facing cascade port, it
will fail to do that, because the FDB entry that already exists is
static and cannot migrate. So address learning should be safe for
this configuration too.
Ok, so what about other MAC addresses coming from the host, not
necessarily the bridge local FDB entries? What about MAC addresses
dynamically learned on foreign interfaces, isn't there a risk that
cascade ports will learn these entries dynamically when they are
supposed to be delivered towards the CPU port? Well, that is correct,
and this is why we also need to enable the assisted learning feature, to
snoop for these addresses and write them to hardware as static FDB
entries towards the CPU, to make the switch's learning process on the
cascade ports ineffective for them. With assisted learning enabled, the
hardware learning on the CPU port must be disabled.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Wed, 4 Aug 2021 13:54:35 +0000 (16:54 +0300)]
net: dsa: sja1105: suppress TX packets from looping back in "H" topologies
H topologies like this one have a problem:
eth0 eth1
| |
CPU port CPU port
| DSA link |
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4 -------- sw1p4 sw1p3 sw1p2 sw1p1 sw1p0
| | | | | |
user user user user user user
port port port port port port
Basically any packet sent by the eth0 DSA master can be flooded on the
interconnecting DSA link sw0p4 <-> sw1p4 and it will be received by the
eth1 DSA master too. Basically we are talking to ourselves.
In VLAN-unaware mode, these packets are encoded using a tag_8021q TX
VLAN, which dsa_8021q_rcv() rightfully cannot decode and complains.
Whereas in VLAN-aware mode, the packets are encoded with a bridge VLAN
which _can_ be decoded by the tagger running on eth1, so it will attempt
to reinject that packet into the network stack (the bridge, if there is
any port under eth1 that is under a bridge). In the case where the ports
under eth1 are under the same cross-chip bridge as the ports under eth0,
the TX packets will even be learned as RX packets. The only thing that
will prevent loops with the software bridging path, and therefore
disaster, is that the source port and the destination port are in the
same hardware domain, and the bridge will receive packets from the
driver with skb->offload_fwd_mark = true and will not forward between
the two.
The proper solution to this problem is to detect H topologies and
enforce that all packets are received through the local switch and we do
not attempt to receive packets on our CPU port from switches that have
their own. This is a viable solution which works thanks to the fact that
MAC addresses which should be filtered towards the host are installed by
DSA as static MAC addresses towards the CPU port of each switch.
TX from a CPU port towards the DSA port continues to be allowed, this is
because sja1105 supports bridge TX forwarding offload, and the skb->dev
used initially for xmit does not have any direct correlation with where
the station that will respond to that packet is connected. It may very
well happen that when we send a ping through a br0 interface that spans
all switch ports, the xmit packet will exit the system through a DSA
switch interface under eth1 (say sw1p2), but the destination station is
connected to a switch port under eth0, like sw0p0. So the switch under
eth1 needs to communicate on TX with the switch under eth0. The
response, however, will not follow the same path, but instead, this
patch enforces that the response is sent by the first switch directly to
its DSA master which is eth0.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Wed, 4 Aug 2021 13:54:34 +0000 (16:54 +0300)]
net: dsa: sja1105: increase MTU to account for VLAN header on DSA ports
Since all packets are transmitted as VLAN-tagged over a DSA link (this
VLAN tag represents the tag_8021q header), we need to increase the MTU
of these interfaces to account for the possibility that we are already
transporting a user-visible VLAN header.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Wed, 4 Aug 2021 13:54:33 +0000 (16:54 +0300)]
net: dsa: sja1105: manage VLANs on cascade ports
Since commit
ed040abca4c1 ("net: dsa: sja1105: use 4095 as the private
VLAN for untagged traffic"), this driver uses a reserved value as pvid
for the host port (DSA CPU port). Control packets which are sent as
untagged get classified to this VLAN, and all ports are members of it
(this is to be expected for control packets).
Manage all cascade ports in the same way and allow control packets to
egress everywhere.
Also, all VLANs need to be sent as egress-tagged on all cascade ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Wed, 4 Aug 2021 13:54:32 +0000 (16:54 +0300)]
net: dsa: sja1105: manage the forwarding domain towards DSA ports
Manage DSA links towards other switches, be they host ports or cascade
ports, the same as the CPU port, i.e. allow forwarding and flooding
unconditionally from all user ports.
We send packets as always VLAN-tagged on a DSA port, and we rely on the
cross-chip notifiers from tag_8021q to install the RX VLAN of a switch
port only on the proper remote ports of another switch (the ports that
are in the same bridging domain). So if there is no cross-chip bridging
in the system, the flooded packets will be sent on the DSA ports too,
but they will be dropped by the remote switches due to either
(a) a lack of the RX VLAN in the VLAN table of the ingress DSA port, or
(b) a lack of valid destinations for those packets, due to a lack of the
RX VLAN on the user ports of the switch
Note that switches which only transport packets in a cross-chip bridge,
but have no user ports of their own as part of that bridge, such as
switch 1 in this case:
DSA link DSA link
sw0p0 sw0p1 sw0p2 -------- sw1p0 sw1p2 sw1p3 -------- sw2p0 sw2p2 sw2p3
ip link set sw0p0 master br0
ip link set sw2p3 master br0
will still work, because the tag_8021q cross-chip notifiers keep the RX
VLANs installed on all DSA ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Wed, 4 Aug 2021 13:54:31 +0000 (16:54 +0300)]
net: dsa: sja1105: configure the cascade ports based on topology
The sja1105 switch family has a feature called "cascade ports" which can
be used in topologies where multiple SJA1105/SJA1110 switches are daisy
chained. Upstream switches set this bit for the DSA link towards the
downstream switches. This is used when the upstream switch receives a
control packet (PTP, STP) from a downstream switch, because if the
source port for a control packet is marked as a cascade port, then the
source port, switch ID and RX timestamp will not be taken again on the
upstream switch, it is assumed that this has already been done by the
downstream switch (the leaf port in the tree) and that the CPU has
everything it needs to decode the information from this packet.
We need to distinguish between an upstream-facing DSA link and a
downstream-facing DSA link, because the upstream-facing DSA links are
"host ports" for the SJA1105/SJA1110 switches, and the downstream-facing
DSA links are "cascade ports".
Note that SJA1105 supports a single cascade port, so only daisy chain
topologies work. With SJA1110, there can be more complex topologies such
as:
eth0
|
host port
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
| | | |
cascade cascade user user
port port port port
| |
| |
| |
| host
| port
| |
| sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
| | | | |
| user user user user
host port port port port
port
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
| | | |
user user user user
port port port port
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Wed, 4 Aug 2021 13:54:30 +0000 (16:54 +0300)]
net: dsa: give preference to local CPU ports
Be there an "H" switch topology, where there are 2 switches connected as
follows:
eth0 eth1
| |
CPU port CPU port
| DSA link |
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4 -------- sw1p4 sw1p3 sw1p2 sw1p1 sw1p0
| | | | | |
user user user user user user
port port port port port port
basically one where each switch has its own CPU port for termination,
but there is also a DSA link in case packets need to be forwarded in
hardware between one switch and another.
DSA insists to see this as a daisy chain topology, basically registering
all network interfaces as sw0p0@eth0, ... sw1p0@eth0 and disregarding
eth1 as a valid DSA master.
This is only half the story, since when asked using dsa_port_is_cpu(),
DSA will respond that sw1p1 is a CPU port, however one which has no
dp->cpu_dp pointing to it. So sw1p1 is enabled, but not used.
Furthermore, be there a driver for switches which support only one
upstream port. This driver iterates through its ports and checks using
dsa_is_upstream_port() whether the current port is an upstream one.
For switch 1, two ports pass the "is upstream port" checks:
- sw1p4 is an upstream port because it is a routing port towards the
dedicated CPU port assigned using dsa_tree_setup_default_cpu()
- sw1p1 is also an upstream port because it is a CPU port, albeit one
that is disabled. This is because dsa_upstream_port() returns:
if (!cpu_dp)
return port;
which means that if @dp does not have a ->cpu_dp pointer (which is a
characteristic of CPU ports themselves as well as unused ports), then
@dp is its own upstream port.
So the driver for switch 1 rightfully says: I have two upstream ports,
but I don't support multiple upstream ports! So let me error out, I
don't know which one to choose and what to do with the other one.
Generally I am against enforcing any default policy in the kernel in
terms of user to CPU port assignment (like round robin or such) but this
case is different. To solve the conundrum, one would have to:
- Disable sw1p1 in the device tree or mark it as "not a CPU port" in
order to comply with DSA's view of this topology as a daisy chain,
where the termination traffic from switch 1 must pass through switch 0.
This is counter-productive because it wastes 1Gbps of termination
throughput in switch 1.
- Disable the DSA link between sw0p4 and sw1p4 and do software
forwarding between switch 0 and 1, and basically treat the switches as
part of disjoint switch trees. This is counter-productive because it
wastes 1Gbps of autonomous forwarding throughput between switch 0 and 1.
- Treat sw0p4 and sw1p4 as user ports instead of DSA links. This could
work, but it makes cross-chip bridging impossible. In this setup we
would need to have 2 separate bridges, br0 spanning the ports of
switch 0, and br1 spanning the ports of switch 1, and the "DSA links
treated as user ports" sw0p4 (part of br0) and sw1p4 (part of br1) are
the gateway ports between one bridge and another. This is hard to
manage from a user's perspective, who wants to have a unified view of
the switching fabric and the ability to transparently add ports to the
same bridge. VLANs would also need to be explicitly managed by the
user on these gateway ports.
So it seems that the only reasonable thing to do is to make DSA prefer
CPU ports that are local to the switch. Meaning that by default, the
user and DSA ports of switch 0 will get assigned to the CPU port from
switch 0 (sw0p1) and the user and DSA ports of switch 1 will get
assigned to the CPU port from switch 1.
The way this solves the problem is that sw1p4 is no longer an upstream
port as far as switch 1 is concerned (it no longer views sw0p1 as its
dedicated CPU port).
So here we are, the first multi-CPU port that DSA supports is also
perhaps the most uneventful one: the individual switches don't support
multiple CPUs, however the DSA switch tree as a whole does have multiple
CPU ports. No user space assignment of user ports to CPU ports is
desirable, necessary, or possible.
Ports that do not have a local CPU port (say there was an extra switch
hanging off of sw0p0) default to the standard implementation of getting
assigned to the first CPU port of the DSA switch tree. Is that good
enough? Probably not (if the downstream switch was hanging off of switch
1, we would most certainly prefer its CPU port to be sw1p1), but in
order to support that use case too, we would need to traverse the
dst->rtable in search of an optimum dedicated CPU port, one that has the
smallest number of hops between dp->ds and dp->cpu_dp->ds. At the
moment, the DSA routing table structure does not keep the number of hops
between dl->dp and dl->link_dp, and while it is probably deducible,
there is zero justification to write that code now. Let's hope DSA will
never have to support that use case.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Wed, 4 Aug 2021 13:54:29 +0000 (16:54 +0300)]
net: dsa: rename teardown_default_cpu to teardown_cpu_ports
There is nothing specific to having a default CPU port to what
dsa_tree_teardown_default_cpu() does. Even with multiple CPU ports,
it would do the same thing: iterate through the ports of this switch
tree and reset the ->cpu_dp pointer to NULL. So rename it accordingly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Wed, 4 Aug 2021 13:54:07 +0000 (08:54 -0500)]
net: ipa: fix IPA v4.9 interconnects
Three interconnects are defined for IPA version 4.9, but there
should only be two. They should also use names that match what's
used for other platforms (and specified in the Device Tree binding).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Wed, 4 Aug 2021 12:15:30 +0000 (13:15 +0100)]
mctp: remove duplicated assignment of pointer hdr
The pointer hdr is being initialized and also re-assigned with the
same value from the call to function mctp_hdr. Static analysis reports
that the initializated value is unused. The second assignment is
duplicated and can be removed.
Addresses-Coverity: ("Unused value").
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Christopherson [Wed, 4 Aug 2021 21:46:09 +0000 (14:46 -0700)]
KVM: x86/mmu: Fix per-cpu counter corruption on 32-bit builds
Take a signed 'long' instead of an 'unsigned long' for the number of
pages to add/subtract to the total number of pages used by the MMU. This
fixes a zero-extension bug on 32-bit kernels that effectively corrupts
the per-cpu counter used by the shrinker.
Per-cpu counters take a signed 64-bit value on both 32-bit and 64-bit
kernels, whereas kvm_mod_used_mmu_pages() takes an unsigned long and thus
an unsigned 32-bit value on 32-bit kernels. As a result, the value used
to adjust the per-cpu counter is zero-extended (unsigned -> signed), not
sign-extended (signed -> signed), and so KVM's intended -1 gets morphed to
4294967295 and effectively corrupts the counter.
This was found by a staggering amount of sheer dumb luck when running
kvm-unit-tests on a 32-bit KVM build. The shrinker just happened to kick
in while running tests and do_shrink_slab() logged an error about trying
to free a negative number of objects. The truly lucky part is that the
kernel just happened to be a slightly stale build, as the shrinker no
longer yells about negative objects as of commit
18bb473e5031 ("mm:
vmscan: shrink deferred objects proportional to priority").
vmscan: shrink_slab: mmu_shrink_scan+0x0/0x210 [kvm] negative objects to delete nr=-
858993460
Fixes:
bc8a3d8925a8 ("kvm: mmu: Fix overflow on kvm mmu page limit calculation")
Cc: stable@vger.kernel.org
Cc: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <
20210804214609.1096003-1-seanjc@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Hui Su [Fri, 11 Jun 2021 02:21:07 +0000 (10:21 +0800)]
scripts/tracing: fix the bug that can't parse raw_trace_func
Since commit
77271ce4b2c0 ("tracing: Add irq, preempt-count and need resched info
to default trace output"), the default trace output format has been changed to:
<idle>-0 [009] d.h. 22420.068695: _raw_spin_lock_irqsave <-hrtimer_interrupt
<idle>-0 [000] ..s. 22420.068695: _nohz_idle_balance <-run_rebalance_domains
<idle>-0 [011] d.h. 22420.068695: account_process_tick <-update_process_times
origin trace output format:(before v3.2.0)
# tracer: nop
#
# TASK-PID CPU# TIMESTAMP FUNCTION
# | | | | |
migration/0-6 [000] 50.025810: rcu_note_context_switch <-__schedule
migration/0-6 [000] 50.025812: trace_rcu_utilization <-rcu_note_context_switch
migration/0-6 [000] 50.025813: rcu_sched_qs <-rcu_note_context_switch
migration/0-6 [000] 50.025815: rcu_preempt_qs <-rcu_note_context_switch
migration/0-6 [000] 50.025817: trace_rcu_utilization <-rcu_note_context_switch
migration/0-6 [000] 50.025818: debug_lockdep_rcu_enabled <-__schedule
migration/0-6 [000] 50.025820: debug_lockdep_rcu_enabled <-__schedule
The draw_functrace.py(introduced in v2.6.28) can't parse the new version format trace_func,
So we need modify draw_functrace.py to adapt the new version trace output format.
Link: https://lkml.kernel.org/r/20210611022107.608787-1-suhui@zeku.com
Cc: stable@vger.kernel.org
Fixes:
77271ce4b2c0 tracing: Add irq, preempt-count and need resched info to default trace output
Signed-off-by: Hui Su <suhui@zeku.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Nathan Chancellor [Mon, 2 Aug 2021 21:03:07 +0000 (14:03 -0700)]
scripts/recordmcount.pl: Remove check_objcopy() and $can_use_local
When building ARCH=riscv allmodconfig with llvm-objcopy, the objcopy
version warning from this script appears:
WARNING: could not find objcopy version or version is less than 2.17.
Local function references are disabled.
The check_objcopy() function in scripts/recordmcount.pl is set up to
parse GNU objcopy's version string, not llvm-objcopy's, which triggers
the warning.
Commit
799c43415442 ("kbuild: thin archives make default for all archs")
made binutils 2.20 mandatory and commit
ba64beb17493 ("kbuild: check the
minimum assembler version in Kconfig") enforces this at configuration
time so just remove check_objcopy() and $can_use_local instead, assuming
--globalize-symbol is always available.
llvm-objcopy has supported --globalize-symbol since LLVM 7.0.0 in 2018
and the minimum version for building the kernel with LLVM is 10.0.1 so
there is no issue introduced:
Link: https://github.com/llvm/llvm-project/commit/ee5be798dae30d5f9414b01f76ff807edbc881aa
Link: https://lkml.kernel.org/r/20210802210307.3202472-1-nathan@kernel.org
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Masami Hiramatsu [Tue, 27 Jul 2021 22:55:43 +0000 (07:55 +0900)]
tracing: Reject string operand in the histogram expression
Since the string type can not be the target of the addition / subtraction
operation, it must be rejected. Without this fix, the string type silently
converted to digits.
Link: https://lkml.kernel.org/r/162742654278.290973.1523000673366456634.stgit@devnote2
Cc: stable@vger.kernel.org
Fixes:
100719dcef447 ("tracing: Add simple expression support to hist triggers")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Steven Rostedt (VMware) [Fri, 30 Jul 2021 21:19:51 +0000 (17:19 -0400)]
tracing / histogram: Give calculation hist_fields a size
When working on my user space applications, I found a bug in the synthetic
event code where the automated synthetic event field was not matching the
event field calculation it was attached to. Looking deeper into it, it was
because the calculation hist_field was not given a size.
The synthetic event fields are matched to their hist_fields either by
having the field have an identical string type, or if that does not match,
then the size and signed values are used to match the fields.
The problem arose when I tried to match a calculation where the fields
were "unsigned int". My tool created a synthetic event of type "u32". But
it failed to match. The string was:
diff=field1-field2:onmatch(event).trace(synth,$diff)
Adding debugging into the kernel, I found that the size of "diff" was 0.
And since it was given "unsigned int" as a type, the histogram fallback
code used size and signed. The signed matched, but the size of u32 (4) did
not match zero, and the event failed to be created.
This can be worse if the field you want to match is not one of the
acceptable fields for a synthetic event. As event fields can have any type
that is supported in Linux, this can cause an issue. For example, if a
type is an enum. Then there's no way to use that with any calculations.
Have the calculation field simply take on the size of what it is
calculating.
Link: https://lkml.kernel.org/r/20210730171951.59c7743f@oasis.local.home
Cc: Tom Zanussi <zanussi@kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@vger.kernel.org
Fixes:
100719dcef447 ("tracing: Add simple expression support to hist triggers")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Sebastian Andrzej Siewior [Tue, 3 Aug 2021 14:16:06 +0000 (16:16 +0200)]
net: Replace deprecated CPU-hotplug functions.
The functions get_online_cpus() and put_online_cpus() have been
deprecated during the CPU hotplug rework. They map directly to
cpus_read_lock() and cpus_read_unlock().
Replace deprecated CPU-hotplug functions with the official version.
The behavior remains unchanged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sebastian Andrzej Siewior [Tue, 3 Aug 2021 14:16:04 +0000 (16:16 +0200)]
virtio_net: Replace deprecated CPU-hotplug functions.
The functions get_online_cpus() and put_online_cpus() have been
deprecated during the CPU hotplug rework. They map directly to
cpus_read_lock() and cpus_read_unlock().
Replace deprecated CPU-hotplug functions with the official version.
The behavior remains unchanged.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Wed, 4 Aug 2021 19:41:30 +0000 (12:41 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Seven fixes, five in drivers.
The two core changes are a trivial warning removal in scsi_scan.c and
a change to rescan for capacity when a device makes a user induced
(via a write to the state variable) offline->running transition to fix
issues with device mapper"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: Fix capacity set to zero after offlinining device
scsi: sr: Return correct event when media event code is 3
scsi: ibmvfc: Fix command state accounting and stale response detection
scsi: core: Avoid printing an error if target_alloc() returns -ENXIO
scsi: scsi_dh_rdac: Avoid crash during rdac_bus_attach()
scsi: megaraid_mm: Fix end of loop tests for list_for_each_entry()
scsi: pm80xx: Fix TMF task completion race condition
Linus Torvalds [Wed, 4 Aug 2021 19:31:53 +0000 (12:31 -0700)]
Merge tag 'gpio-updates-for-v5.14-rc5' of git://git./linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- revert a patch intruducing breakage in interrupt handling in
gpio-mpc8xxx
- correctly handle missing IRQs in gpio-tqmx86 by really making them
optional
* tag 'gpio-updates-for-v5.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: tqmx86: really make IRQ optional
Revert "gpio: mpc8xxx: change the gpio interrupt flags."
Maxim Levitsky [Wed, 4 Aug 2021 11:20:57 +0000 (14:20 +0300)]
KVM: selftests: fix hyperv_clock test
The test was mistakenly using addr_gpa2hva on a gva and that happened
to work accidentally. Commit
106a2e766eae ("KVM: selftests: Lower the
min virtual address for misc page allocations") revealed this bug.
Fixes:
2c7f76b4c42b ("selftests: kvm: Add basic Hyper-V clocksources tests", 2021-03-18)
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <
20210804112057.409498-1-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Mingwei Zhang [Mon, 2 Aug 2021 18:09:03 +0000 (11:09 -0700)]
KVM: SVM: improve the code readability for ASID management
KVM SEV code uses bitmaps to manage ASID states. ASID 0 was always skipped
because it is never used by VM. Thus, in existing code, ASID value and its
bitmap postion always has an 'offset-by-1' relationship.
Both SEV and SEV-ES shares the ASID space, thus KVM uses a dynamic range
[min_asid, max_asid] to handle SEV and SEV-ES ASIDs separately.
Existing code mixes the usage of ASID value and its bitmap position by
using the same variable called 'min_asid'.
Fix the min_asid usage: ensure that its usage is consistent with its name;
allocate extra size for ASID 0 to ensure that each ASID has the same value
with its bitmap position. Add comments on ASID bitmap allocation to clarify
the size change.
Signed-off-by: Mingwei Zhang <mizhang@google.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Marc Orr <marcorr@google.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Alper Gun <alpergun@google.com>
Cc: Dionna Glaze <dionnaglaze@google.com>
Cc: Sean Christopherson <seanjc@google.com>
Cc: Vipin Sharma <vipinsh@google.com>
Cc: Peter Gonda <pgonda@google.com>
Cc: Joerg Roedel <joro@8bytes.org>
Message-Id: <
20210802180903.159381-1-mizhang@google.com>
[Fix up sev_asid_free to also index by ASID, as suggested by Sean
Christopherson, and use nr_asids in sev_cpu_init. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Nick Richardson [Tue, 3 Aug 2021 16:27:35 +0000 (16:27 +0000)]
pktgen: Remove redundant clone_skb override
When the netif_receive xmit_mode is set, a line is supposed to set
clone_skb to a default 0 value. This line is made redundant due to a
preceding line that checks if clone_skb is more than zero and returns
-ENOTSUPP.
Overriding clone_skb to 0 does not make any difference to the behavior
because if it was positive we return error. So it can be either 0 or
negative, and in both cases the behavior is the same.
Remove redundant line that sets clone_skb to zero.
Signed-off-by: Nick Richardson <richardsonnick@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathan Lemon [Wed, 4 Aug 2021 03:33:27 +0000 (20:33 -0700)]
ptp: ocp: Expose various resources on the timecard.
The OpenCompute timecard driver has additional functionality besides
a clock. Make the following resources available:
- The external timestamp channels (ts0/ts1)
- devlink support for flashing and health reporting
- GPS and MAC serial ports
- board serial number (obtained from i2c device)
Also add watchdog functionality for when GNSS goes into holdover.
The resources are collected under a timecard class directory:
[jlemon@timecard ~]$ ls -g /sys/class/timecard/ocp1/
total 0
-r--r--r--. 1 root 4096 Aug 3 19:49 available_clock_sources
-rw-r--r--. 1 root 4096 Aug 3 19:49 clock_source
lrwxrwxrwx. 1 root 0 Aug 3 19:49 device -> ../../../0000:04:00.0/
-r--r--r--. 1 root 4096 Aug 3 19:49 gps_sync
lrwxrwxrwx. 1 root 0 Aug 3 19:49 i2c -> ../../xiic-i2c.1024/i2c-2/
drwxr-xr-x. 2 root 0 Aug 3 19:49 power/
lrwxrwxrwx. 1 root 0 Aug 3 19:49 pps ->
../../../../../virtual/pps/pps1/
lrwxrwxrwx. 1 root 0 Aug 3 19:49 ptp -> ../../ptp/ptp2/
-r--r--r--. 1 root 4096 Aug 3 19:49 serialnum
lrwxrwxrwx. 1 root 0 Aug 3 19:49 subsystem ->
../../../../../../class/timecard/
lrwxrwxrwx. 1 root 0 Aug 3 19:49 ttyGPS -> ../../tty/ttyS7/
lrwxrwxrwx. 1 root 0 Aug 3 19:49 ttyMAC -> ../../tty/ttyS8/
-rw-r--r--. 1 root 4096 Aug 3 19:39 uevent
The labeling is needed at the minimum, in order to tell the serial
devices apart.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Tikhomirov [Wed, 4 Aug 2021 07:55:56 +0000 (10:55 +0300)]
sock: allow reading and changing sk_userlocks with setsockopt
SOCK_SNDBUF_LOCK and SOCK_RCVBUF_LOCK flags disable automatic socket
buffers adjustment done by kernel (see tcp_fixup_rcvbuf() and
tcp_sndbuf_expand()). If we've just created a new socket this adjustment
is enabled on it, but if one changes the socket buffer size by
setsockopt(SO_{SND,RCV}BUF*) it becomes disabled.
CRIU needs to call setsockopt(SO_{SND,RCV}BUF*) on each socket on
restore as it first needs to increase buffer sizes for packet queues
restore and second it needs to restore back original buffer sizes. So
after CRIU restore all sockets become non-auto-adjustable, which can
decrease network performance of restored applications significantly.
CRIU need to be able to restore sockets with enabled/disabled adjustment
to the same state it was before dump, so let's add special setsockopt
for it.
Let's also export SOCK_SNDBUF_LOCK and SOCK_RCVBUF_LOCK flags to uAPI so
that using these interface one can reenable automatic socket buffer
adjustment on their sockets.
Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan T. Ivanov [Wed, 4 Aug 2021 08:13:39 +0000 (11:13 +0300)]
net: usb: lan78xx: don't modify phy_device state concurrently
Currently phy_device state could be left in inconsistent state shown
by following alert message[1]. This is because phy_read_status could
be called concurrently from lan78xx_delayedwork, phy_state_machine and
__ethtool_get_link. Fix this by making sure that phy_device state is
updated atomically.
[1] lan78xx 1-1.1.1:1.0 eth0: No phy led trigger registered for speed(-1)
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 3 Aug 2021 23:14:15 +0000 (16:14 -0700)]
docs: networking: netdevsim rules
There are aspects of netdevsim which are commonly
misunderstood and pointed out in review. Cong
suggest we document them.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peilin Ye [Tue, 3 Aug 2021 22:16:59 +0000 (15:16 -0700)]
tc-testing: Add control-plane selftests for sch_mq
Recently we added multi-queue support to netdevsim in commit
d4861fc6be58
("netdevsim: Add multi-queue support"); add a few control-plane selftests
for sch_mq using this new feature.
Use nsPlugin.py to avoid network interface name collisions.
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 3 Aug 2021 20:34:09 +0000 (23:34 +0300)]
Revert "net: build all switchdev drivers as modules when the bridge is a module"
This reverts commit
b0e81817629a496854ff1799f6cbd89597db65fd. Explicit
driver dependency on the bridge is no longer needed since
switchdev_bridge_port_{,un}offload() is no longer implemented by the
bridge driver but by switchdev.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 3 Aug 2021 20:34:08 +0000 (23:34 +0300)]
net: make switchdev_bridge_port_{,unoffload} loosely coupled with the bridge
With the introduction of explicit offloading API in switchdev in commit
2f5dc00f7a3e ("net: bridge: switchdev: let drivers inform which bridge
ports are offloaded"), we started having Ethernet switch drivers calling
directly into a function exported by net/bridge/br_switchdev.c, which is
a function exported by the bridge driver.
This means that drivers that did not have an explicit dependency on the
bridge before, like cpsw and am65-cpsw, now do - otherwise it is not
possible to call a symbol exported by a driver that can be built as
module unless you are a module too.
There was an attempt to solve the dependency issue in the form of commit
b0e81817629a ("net: build all switchdev drivers as modules when the
bridge is a module"). Grygorii Strashko, however, says about it:
| In my opinion, the problem is a bit bigger here than just fixing the
| build :(
|
| In case, of ^cpsw the switchdev mode is kinda optional and in many
| cases (especially for testing purposes, NFS) the multi-mac mode is
| still preferable mode.
|
| There were no such tight dependency between switchdev drivers and
| bridge core before and switchdev serviced as independent, notification
| based layer between them, so ^cpsw still can be "Y" and bridge can be
| "M". Now for mostly every kernel build configuration the CONFIG_BRIDGE
| will need to be set as "Y", or we will have to update drivers to
| support build with BRIDGE=n and maintain separate builds for
| networking vs non-networking testing. But is this enough? Wouldn't
| it cause 'chain reaction' required to add more and more "Y" options
| (like CONFIG_VLAN_8021Q)?
|
| PS. Just to be sure we on the same page - ARM builds will be forced
| (with this patch) to have CONFIG_TI_CPSW_SWITCHDEV=m and so all our
| automation testing will just fail with omap2plus_defconfig.
In the light of this, it would be desirable for some configurations to
avoid dependencies between switchdev drivers and the bridge, and have
the switchdev mode as completely optional within the driver.
Arnd Bergmann also tried to write a patch which better expressed the
build time dependency for Ethernet switch drivers where the switchdev
support is optional, like cpsw/am65-cpsw, and this made the drivers
follow the bridge (compile as module if the bridge is a module) only if
the optional switchdev support in the driver was enabled in the first
place:
https://patchwork.kernel.org/project/netdevbpf/patch/
20210802144813.1152762-1-arnd@kernel.org/
but this still did not solve the fact that cpsw and am65-cpsw now must
be built as modules when the bridge is a module - it just expressed
correctly that optional dependency. But the new behavior is an apparent
regression from Grygorii's perspective.
So to support the use case where the Ethernet driver is built-in,
NET_SWITCHDEV (a bool option) is enabled, and the bridge is a module, we
need a framework that can handle the possible absence of the bridge from
the running system, i.e. runtime bloatware as opposed to build-time
bloatware.
Luckily we already have this framework, since switchdev has been using
it extensively. Events from the bridge side are transmitted to the
driver side using notifier chains - this was originally done so that
unrelated drivers could snoop for events emitted by the bridge towards
ports that are implemented by other drivers (think of a switch driver
with LAG offload that listens for switchdev events on a bonding/team
interface that it offloads).
There are also events which are transmitted from the driver side to the
bridge side, which again are modeled using notifiers.
SWITCHDEV_FDB_ADD_TO_BRIDGE is an example of this, and deals with
notifying the bridge that a MAC address has been dynamically learned.
So there is a precedent we can use for modeling the new framework.
The difference compared to SWITCHDEV_FDB_ADD_TO_BRIDGE is that the work
that the bridge needs to do when a port becomes offloaded is blocking in
its nature: replay VLANs, MDBs etc. The calling context is indeed
blocking (we are under rtnl_mutex), but the existing switchdev
notification chain that the bridge is subscribed to is only the atomic
one. So we need to subscribe the bridge to the blocking switchdev
notification chain too.
This patch:
- keeps the driver-side perception of the switchdev_bridge_port_{,un}offload
unchanged
- moves the implementation of switchdev_bridge_port_{,un}offload from
the bridge module into the switchdev module.
- makes everybody that is subscribed to the switchdev blocking notifier
chain "hear" offload & unoffload events
- makes the bridge driver subscribe and handle those events
- moves the bridge driver's handling of those events into 2 new
functions called br_switchdev_port_{,un}offload. These functions
contain in fact the core of the logic that was previously in
switchdev_bridge_port_{,un}offload, just that now we go through an
extra indirection layer to reach them.
Unlike all the other switchdev notification structures, the structure
used to carry the bridge port information, struct
switchdev_notifier_brport_info, does not contain a "bool handled".
This is because in the current usage pattern, we always know that a
switchdev bridge port offloading event will be handled by the bridge,
because the switchdev_bridge_port_offload() call was initiated by a
NETDEV_CHANGEUPPER event in the first place, where info->upper_dev is a
bridge. So if the bridge wasn't loaded, then the CHANGEUPPER event
couldn't have happened.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 4 Aug 2021 10:30:09 +0000 (11:30 +0100)]
Merge tag 'linux-can-next-for-5.15-
20210804' of git://git./linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2021-08-04
this is a pull request of 5 patches for net-next/master.
The first patch is by me and fixes a typo in a comment in the CAN
J1939 protocol.
The next 2 patches are by Oleksij Rempel and update the CAN J1939
protocol to send RX status updates via the error queue mechanism.
The next patch is by me and adds a missing variable initialization to
the flexcan driver (the problem was introduced in the current net-next
cycle).
The last patch is by Aswath Govindraju and adds power-domains to the
Bosch m_can DT binding documentation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Aswath Govindraju [Mon, 2 Aug 2021 09:18:22 +0000 (14:48 +0530)]
dt-bindings: net: can: Document power-domains property
Document power-domains property for adding the Power domain provider.
Link: https://lore.kernel.org/r/20210802091822.16407-1-a-govindraju@ti.com
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 28 Jul 2021 07:51:42 +0000 (09:51 +0200)]
can: flexcan: flexcan_clks_enable(): add missing variable initialization
This patch adds the missing initialization of the "err" variable in
the flexcan_clks_enable() function.
Fixes:
d9cead75b1c6 ("can: flexcan: add mcf5441x support")
Link: https://lore.kernel.org/r/20210728075428.1493568-1-mkl@pengutronix.de
Reported-by: kernel test robot <lkp@intel.com>
Cc: Angelo Dureghello <angelo@kernel-space.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oleksij Rempel [Wed, 7 Jul 2021 09:48:54 +0000 (11:48 +0200)]
can: j1939: extend UAPI to notify about RX status
To be able to create applications with user friendly feedback, we need be
able to provide receive status information.
Typical ETP transfer may take seconds or even hours. To give user some
clue or show a progress bar, the stack should push status updates.
Same as for the TX information, the socket error queue will be used with
following new signals:
- J1939_EE_INFO_RX_RTS - received and accepted request to send signal.
- J1939_EE_INFO_RX_DPO - received data package offset signal
- J1939_EE_INFO_RX_ABORT - RX session was aborted
Instead of completion signal, user will get data package.
To activate this signals, application should set
SOF_TIMESTAMPING_RX_SOFTWARE to the SO_TIMESTAMPING socket option. This
will avoid unpredictable application behavior for the old software.
Link: https://lore.kernel.org/r/20210707094854.30781-3-o.rempel@pengutronix.de
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oleksij Rempel [Wed, 7 Jul 2021 09:48:53 +0000 (11:48 +0200)]
can: j1939: rename J1939_ERRQUEUE_* to J1939_ERRQUEUE_TX_*
Prepare the world for the J1939_ERRQUEUE_RX_ version
Link: https://lore.kernel.org/r/20210707094854.30781-2-o.rempel@pengutronix.de
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sean Christopherson [Tue, 3 Aug 2021 16:27:46 +0000 (09:27 -0700)]
KVM: SVM: Fix off-by-one indexing when nullifying last used SEV VMCB
Use the raw ASID, not ASID-1, when nullifying the last used VMCB when
freeing an SEV ASID. The consumer, pre_sev_run(), indexes the array by
the raw ASID, thus KVM could get a false negative when checking for a
different VMCB if KVM manages to reallocate the same ASID+VMCB combo for
a new VM.
Note, this cannot cause a functional issue _in the current code_, as
pre_sev_run() also checks which pCPU last did VMRUN for the vCPU, and
last_vmentry_cpu is initialized to -1 during vCPU creation, i.e. is
guaranteed to mismatch on the first VMRUN. However, prior to commit
8a14fe4f0c54 ("kvm: x86: Move last_cpu into kvm_vcpu_arch as
last_vmentry_cpu"), SVM tracked pCPU on its own and zero-initialized the
last_cpu variable. Thus it's theoretically possible that older versions
of KVM could miss a TLB flush if the first VMRUN is on pCPU0 and the ASID
and VMCB exactly match those of a prior VM.
Fixes:
70cd94e60c73 ("KVM: SVM: VMRUN should use associated ASID when SEV is enabled")
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Wed, 4 Aug 2021 09:28:52 +0000 (05:28 -0400)]
KVM: Do not leak memory for duplicate debugfs directories
KVM creates a debugfs directory for each VM in order to store statistics
about the virtual machine. The directory name is built from the process
pid and a VM fd. While generally unique, it is possible to keep a
file descriptor alive in a way that causes duplicate directories, which
manifests as these messages:
[ 471.846235] debugfs: Directory '20245-4' with parent 'kvm' already present!
Even though this should not happen in practice, it is more or less
expected in the case of KVM for testcases that call KVM_CREATE_VM and
close the resulting file descriptor repeatedly and in parallel.
When this happens, debugfs_create_dir() returns an error but
kvm_create_vm_debugfs() goes on to allocate stat data structs which are
later leaked. The slow memory leak was spotted by syzkaller, where it
caused OOM reports.
Since the issue only affects debugfs, do a lookup before calling
debugfs_create_dir, so that the message is downgraded and rate-limited.
While at it, ensure kvm->debugfs_dentry is NULL rather than an error
if it is not created. This fixes kvm_destroy_vm_debugfs, which was not
checking IS_ERR_OR_NULL correctly.
Cc: stable@vger.kernel.org
Fixes:
536a6f88c49d ("KVM: Create debugfs dir and stat files for each VM")
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
David S. Miller [Wed, 4 Aug 2021 09:45:41 +0000 (10:45 +0100)]
Merge branch 'master' of git://git./linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2021-08-04
1) Fix a sysbot reported memory leak in xfrm_user_rcv_msg.
From Pavel Skripkin.
2) Revert "xfrm: policy: Read seqcount outside of rcu-read side
in xfrm_policy_lookup_bytype". This commit tried to fix a
lockin bug, but only cured some of the symptoms. A proper
fix is applied on top of this revert.
3) Fix a locking bug on xfrm state hash resize. A recent change
on sequence counters accidentally repaced a spinlock by a mutex.
Fix from Frederic Weisbecker.
4) Fix possible user-memory-access in xfrm_user_rcv_msg_compat().
From Dmitry Safonov.
5) Add initialiation sefltest fot xfrm_spdattr_type_t.
From Dmitry Safonov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 4 Aug 2021 09:38:42 +0000 (10:38 +0100)]
Merge branch 'pegasus-errors'
Petko Manolov says:
====================
net: usb: pegasus: better error checking and DRIVER_VERSION removal
v3:
Pavel Skripkin again: make sure -ETIMEDOUT is returned by __mii_op() on timeout
condition;
v2:
Special thanks to Pavel Skripkin for the review and who caught a few bugs.
setup_pegasus_II() would not print an erroneous message on the success path.
v1:
Add error checking for get_registers() and derivatives. If the usb transfer
fail then just don't use the buffer where the legal data should have been
returned.
Remove DRIVER_VERSION per Greg KH request.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petko Manolov [Tue, 3 Aug 2021 17:25:24 +0000 (20:25 +0300)]
net: usb: pegasus: Remove the changelog and DRIVER_VERSION.
These are now deemed redundant.
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petko Manolov [Tue, 3 Aug 2021 17:25:23 +0000 (20:25 +0300)]
net: usb: pegasus: Check the return value of get_geristers() and friends;
Certain call sites of get_geristers() did not do proper error handling. This
could be a problem as get_geristers() typically return the data via pointer to a
buffer. If an error occurred the code is carelessly manipulating the wrong data.
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Reviewed-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 3 Aug 2021 15:31:05 +0000 (08:31 -0700)]
ipv6: exthdrs: get rid of indirect calls in ip6_parse_tlv()
As presented last month in our "BIG TCP" talk at netdev 0x15,
we plan using IPv6 jumbograms.
One of the minor problem we talked about is the fact that
ip6_parse_tlv() is currently using tables to list known tlvs,
thus using potentially expensive indirect calls.
While we could mitigate this cost using macros from
indirect_call_wrapper.h, we also can get rid of the tables
and let the compiler emit optimized code.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Justin Iurman <justin.iurman@uliege.be>
Cc: Coco Li <lixiaoyan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 4 Aug 2021 09:30:00 +0000 (10:30 +0100)]
Merge branch 'm7530-sw-fallback'
DENG Qingfang says:
====================
mt7530 software fallback bridging fix
DSA core has gained software fallback support since commit
2f5dc00f7a3e,
but it does not work properly on mt7530. This patch series fixes the
issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
DENG Qingfang [Tue, 3 Aug 2021 16:04:04 +0000 (00:04 +0800)]
net: dsa: mt7530: always install FDB entries with IVL and FID 1
This reverts commit
7e777021780e ("mt7530 mt7530_fdb_write only set ivl
bit vid larger than 1").
Before this series, the default value of all ports' PVID is 1, which is
copied into the FDB entry, even if the ports are VLAN unaware. So
`bridge fdb show` will show entries like `dev swp0 vlan 1 self` even on
a VLAN-unaware bridge.
The blamed commit does not solve that issue completely, instead it may
cause a new issue that FDB is inaccessible in a VLAN-aware bridge with
PVID 1.
This series sets PVID to 0 on VLAN-unaware ports, so `bridge fdb show`
will no longer print `vlan 1` on VLAN-unaware bridges, and that special
case in fdb_write is not required anymore.
Set FDB entries' filter ID to 1 to match the VLAN table.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DENG Qingfang [Tue, 3 Aug 2021 16:04:03 +0000 (00:04 +0800)]
net: dsa: mt7530: set STP state on filter ID 1
As filter ID 1 is the only one used for bridges, set STP state on it.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DENG Qingfang [Tue, 3 Aug 2021 16:04:02 +0000 (00:04 +0800)]
net: dsa: mt7530: use independent VLAN learning on VLAN-unaware bridges
Consider the following bridge configuration, where bond0 is not
offloaded:
+-- br0 --+
/ / | \
/ / | \
/ | | bond0
/ | | / \
swp0 swp1 swp2 swp3 swp4
. . .
. . .
A B C
Ideally, when the switch receives a packet from swp3 or swp4, it should
forward the packet to the CPU, according to the port matrix and unknown
unicast flood settings.
But packet loss will happen if the destination address is at one of the
offloaded ports (swp0~2). For example, when client C sends a packet to
A, the FDB lookup will indicate that it should be forwarded to swp0, but
the port matrix of swp3 and swp4 is configured to only allow the CPU to
be its destination, so it is dropped.
However, this issue does not happen if the bridge is VLAN-aware. That is
because VLAN-aware bridges use independent VLAN learning, i.e. use VID
for FDB lookup, on offloaded ports. As swp3 and swp4 are not offloaded,
shared VLAN learning with default filter ID of 0 is used instead. So the
lookup for A with filter ID 0 never hits and the packet can be forwarded
to the CPU.
In the current code, only two combinations were used to toggle user
ports' VLAN awareness: one is PCR.PORT_VLAN set to port matrix mode with
PVC.VLAN_ATTR set to transparent port, the other is PCR.PORT_VLAN set to
security mode with PVC.VLAN_ATTR set to user port.
It turns out that only PVC.VLAN_ATTR contributes to VLAN awareness, and
port matrix mode just skips the VLAN table lookup. The reference manual
is somehow misleading when describing PORT_VLAN modes. It states that
PORT_MEM (VLAN port member) is used for destination if the VLAN table
lookup hits, but actually **PORT_MEM & PORT_MATRIX** (bitwise AND of
VLAN port member and port matrix) is used instead, which means we can
have two or more separate VLAN-aware bridges with the same PVID and
traffic won't leak between them.
Therefore, to solve this, enable independent VLAN learning with PVID 0
on VLAN-unaware bridges, by setting their PCR.PORT_VLAN to fallback
mode, while leaving standalone ports in port matrix mode. The CPU port
is always set to fallback mode to serve those bridges.
During testing, it is found that FDB lookup with filter ID of 0 will
also hit entries with VID 0 even with independent VLAN learning. To
avoid that, install all VLANs with filter ID of 1.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DENG Qingfang [Tue, 3 Aug 2021 16:04:01 +0000 (00:04 +0800)]
net: dsa: mt7530: enable assisted learning on CPU port
Consider the following bridge configuration, where bond0 is not
offloaded:
+-- br0 --+
/ / | \
/ / | \
/ | | bond0
/ | | / \
swp0 swp1 swp2 swp3 swp4
. . .
. . .
A B C
Address learning is enabled on offloaded ports (swp0~2) and the CPU
port, so when client A sends a packet to C, the following will happen:
1. The switch learns that client A can be reached at swp0.
2. The switch probably already knows that client C can be reached at the
CPU port, so it forwards the packet to the CPU.
3. The bridge core knows client C can be reached at bond0, so it
forwards the packet back to the switch.
4. The switch learns that client A can be reached at the CPU port.
5. The switch forwards the packet to either swp3 or swp4, according to
the packet's tag.
That makes client A's MAC address flap between swp0 and the CPU port. If
client B sends a packet to A, it is possible that the packet is
forwarded to the CPU. With offload_fwd_mark = 1, the bridge core won't
forward it back to the switch, resulting in packet loss.
As we have the assisted_learning_on_cpu_port in DSA core now, enable
that and disable hardware learning on the CPU port.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <oltean@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / platform / kernel / linux-starfive.git / log