Arnd Bergmann [Mon, 19 Sep 2016 15:38:38 +0000 (17:38 +0200)]
Merge tag 'davinci-for-v4.9/dts-p2' of git://git./linux/kernel/git/nsekhar/linux-davinci into next/dt
Pull "DaVinci DTS updates for v4.9 (part 2)" from Sekhar Nori:
This pull request adds NAND support to
DA850 based LCDK board.
* tag 'davinci-for-v4.9/dts-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-lcdk: Add NAND to DT
Arnd Bergmann [Mon, 19 Sep 2016 15:37:07 +0000 (17:37 +0200)]
Merge tag 'sti-dt-for-v4.9-3' of git://git./linux/kernel/git/pchotard/sti into next/dt
Pull "STi clock improvement for video playback" from Patrice Chotard:
This serie allows to increase video resolutions and make audio
adjustment during a video playback for STiH407 family socs.
* tag 'sti-dt-for-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: STiH410: clock configuration to address 720p and 1080p
ARM: dts: STi: STiH407: clock configuration to address 720p and 1080p
ARM: dts: STiH418: Enable synchronous clock mode for video clocks
ARM: dts: STiH410: Enable synchronous clock mode for video clocks
ARM: dts: STiH407: Enable synchronous clock mode for video clocks
ARM: dts: STiH418: Enable clock propagation for audio clocks
ARM: dts: STiH410: Enable clock propagation for audio clocks
ARM: dts: STiH407: Enable clock propagation for audio clocks
ARM: dts: STiH4xx: Simplify clock binding of STiH4xx platforms
Arnd Bergmann [Mon, 19 Sep 2016 15:35:33 +0000 (17:35 +0200)]
Merge tag 'sti-dt-for-v4.9-2' of git://git./linux/kernel/git/pchotard/sti into next/dt
Pull "STi dts update" from Patrice Chotard:
Update gpio-cells and gpio specifier for STiH415/416
Add PWM capture support for STiH416 and STiH407 family
Add USB3 support for B2260
Add HVA support for STiH410
Add clk_ignore_unused in bootargs of B2260
Add Flexible Direct Memory Access (FDMA) support for STiH407 family
Add internal audio codec IP spport for STiH407 family
Add uniperif player/reader IP blocks for STiH407 family
* tag 'sti-dt-for-v4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti: (22 commits)
ARM: DT: STi: stihxxx-b2120: Add DT nodes for STi audio card
ARM: STi: DT: STiH407: Add uniperif reader dt nodes
ARM: STi: DT: STiH407: Add uniperif player dt nodes
ARM: STi: DT: STiH407: Add sti-sasg-codec dt node
ARM: DT: STiH407: Add spdif_out pinctrl config
ARM: DT: STiH407: Add i2s_in pinctrl configuration
ARM: DT: STiH407: Add i2s_out pinctrl configuration
ARM: STi: DT: STiH407: Add FDMA driver dt nodes.
ARM: dts: STiH410: Add hva dt nodes
ARM: dts: STiH410-b2260: add clk_ignore_unused in bootargs
ARM: dts: STiH410-b2260: add USB3 node
ARM: dts: STiH416: Define the number of PWM Capture channels
ARM: dts: STiH416: Define PWM Capture clock
ARM: dts: STiH416: Declare PWM Capture data lines via Pinctrl
ARM: dts: STiH416: Supply PWM Capture IRQs
ARM: dts: STiH407: Declare PWM Capture data lines via Pinctrl
ARM: dts: STiH407: Supply PWM Capture IRQ
ARM: dts: STiH416-b2020e: update gpio specifier
ARM: dts: STiH41x-b2000: update gpio specifier
ARM: dts: STiHxxx-b2120: update gpio specifier
...
Arnd Bergmann [Mon, 19 Sep 2016 15:31:45 +0000 (17:31 +0200)]
Merge tag 'amlogic-dt' of git://git./linux/kernel/git/khilman/linux-amlogic into next/dt
Pull "Amlogic DT updates for v4.9" from Kevin Hilman:
- add PWM support
* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson8b: Add Meson8b PWM Controller nodes
Arnd Bergmann [Mon, 19 Sep 2016 15:30:06 +0000 (17:30 +0200)]
Merge tag 'mvebu-dt-4.9-2' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt for 4.9 (part 2)" from Gregory CLEMENT:
- convert orion5x based SoC Netgear WNR854T to devicetree
- remove obsolete orion-gpio binding description
* tag 'mvebu-dt-4.9-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: orion5x: Configure WNR854T ethernet PHY LEDs
ARM: dts: orion5x: Add description for Netgear WNR854T
ARM: dts: arm: orion5x: Add DT include for mv88f5181
dt-bindings: arm: add DT binding for Marvell Orion5x SoC family
ARM: dts: orion5x: Add required properties for orion-wdt to DT node
dt-binding: mrvl-gpio: remove orion-gpio description
Arnd Bergmann [Mon, 19 Sep 2016 15:28:09 +0000 (17:28 +0200)]
Merge tag 'at91-ab-4.9-dt1' of git://git./linux/kernel/git/abelloni/linux into next/dt
Pull "DT Changes for 4.9" from Alexandre Belloni:
- add ETM and ETB nodes on sama5d2
* tag 'at91-ab-4.9-dt1' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: sama5d2: add ETM and ETB nodes
Gabriel Fernandez [Mon, 29 Aug 2016 12:27:00 +0000 (14:27 +0200)]
ARM: dts: STiH410: clock configuration to address 720p and 1080p
It is necessary to properly configure these clocks in order
to address 720p and 1080p HDMI resolution.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Gabriel Fernandez [Mon, 29 Aug 2016 12:27:00 +0000 (14:27 +0200)]
ARM: dts: STi: STiH407: clock configuration to address 720p and 1080p
It is necessary to properly configure these clocks in order
to address 720p and 1080p HDMI resolution.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Gabriel Fernandez [Mon, 29 Aug 2016 12:27:00 +0000 (14:27 +0200)]
ARM: dts: STiH418: Enable synchronous clock mode for video clocks
This patch enables the synchronous clock mode for video clocks
on STiH418 board.
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Gabriel Fernandez [Mon, 29 Aug 2016 12:27:00 +0000 (14:27 +0200)]
ARM: dts: STiH410: Enable synchronous clock mode for video clocks
This patch enables the synchronous clock mode for video clocks
on STiH410 board.
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Gabriel Fernandez [Mon, 29 Aug 2016 12:27:00 +0000 (14:27 +0200)]
ARM: dts: STiH407: Enable synchronous clock mode for video clocks
This patch enables the synchronous clock mode for video clocks
on STiH407 board.
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Gabriel Fernandez [Mon, 29 Aug 2016 12:27:00 +0000 (14:27 +0200)]
ARM: dts: STiH418: Enable clock propagation for audio clocks
This patch is used in the clock driver to apply a clock propagation
flag on the audio clocks of STiH418
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Gabriel Fernandez [Mon, 29 Aug 2016 12:27:00 +0000 (14:27 +0200)]
ARM: dts: STiH410: Enable clock propagation for audio clocks
This patch is used in the clock driver to apply a clock propagation
flag on the audio clocks of STiH410
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Gabriel Fernandez [Mon, 29 Aug 2016 12:26:00 +0000 (14:26 +0200)]
ARM: dts: STiH407: Enable clock propagation for audio clocks
This patch is used in the clock driver to apply a clock propagation
flag on the audio clocks of STiH407
Signed-off-by: Olivier Bideau <olivier.bideau@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Gabriel Fernandez [Mon, 29 Aug 2016 12:26:00 +0000 (14:26 +0200)]
ARM: dts: STiH4xx: Simplify clock binding of STiH4xx platforms
This patch simplifies the clock binding because we had too much detail.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Karl Beldan [Thu, 8 Sep 2016 18:33:24 +0000 (11:33 -0700)]
ARM: dts: da850-lcdk: Add NAND to DT
This adds DT support for the NAND connected to the SoC AEMIF.
Passed torture hashing a 40MB file on top of UBIFS using subpages.
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
[khilman: add back default partitions from an earlier patch]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Arnd Bergmann [Thu, 15 Sep 2016 09:44:02 +0000 (11:44 +0200)]
Merge tag 'davinci-for-v4.9/dts' of git://git./linux/kernel/git/nsekhar/linux-davinci into next/dt
Pull "DaVinci DA850 device-tree enhancements include" from Sekhar Nori:
- Support for new board OMAP-L138 LCDK
- Add AEMIF node on DA850 EVM and use it for NAND
- Audio support for LCDK
- Cleanups for PWM and UART
* tag 'davinci-for-v4.9/dts' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-lcdk: Audio support via simple-card
ARM: dts: da850,da850-evm: Add an aemif node and use it for the NAND
ARM: dts: da850: Add basic DTS for the LCDK
ARM: dts: da850: Add missing pin muxing for the UARTs
ARM: dts: da850: Add new ECAP and EPWM bindings
Arnd Bergmann [Wed, 14 Sep 2016 22:44:55 +0000 (00:44 +0200)]
Merge tag 'arm-soc/for-4.9/devicetree' of github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.9" from Florian Fainelli:
This pull request contains Broadcom ARM-based Device Tree changes for v4.9,
please pull the following:
- Jon adds support for the Ethernet MAC DT nodes (AMAC) and provides the
following updates for Broadcom references boards:
* New Northstar Plus reference boards added: BCM958525er, BCM958522er,
BCM988312hr, BCM958623hr and BCM958622hr
* Add SATA nodes to the BCM958625hr and XMC boards
* Add I2C nodes to the XMC board
* Fixes the amount of RAM on BCM958625HR, BCM958625K and BCM958525XMC boards
* Add the GPIO reboot method for BCM958625hr and XMC boards
- Dhanajay adds PWM nodes for the Northstar Plus SoCs
- Rafal adds the USB 2.0 PHY to the BCM5301x Device Tree file include
- Stefan adds a missing USB clock to the BCM283x DT files, adds a DTSI file for
the USB host mode on BCM283x and finally documents and adds support for the
Raspberry Pi Zero
- Florian adds support for the Northstar Plus Switch Register Access block which
enables the integrated switch on these SoCs and enables the switch ports on the
BCM958625HR reference board
* tag 'arm-soc/for-4.9/devicetree' of http://github.com/Broadcom/stblinux: (22 commits)
ARM: dts: bcm2835: Add Raspberry Pi Zero
DT: bindings: bcm: Add Raspberry Pi Zero
ARM: dts: bcm283x: Add dtsi for USB host mode
ARM: dts: bcm283x: Add missing USB clock
ARM: dts: NSP: Add new DT file for bcm958622hr
ARM: dts: NSP: Add new DT file for bcm958623hr
ARM: dts: NSP: Add new DT file for bcm988312hr
ARM: dts: NSP: Add new DT file for bcm958522er
ARM: dts: NSP: Add new DT file for bcm958525er
ARM: dts: NSP: Add GPIO reboot method to bcm958625xmc DTS file
ARM: dts: NSP: Add GPIO reboot method to bcm958625hr DTS file
ARM: dts: NSP: Specify RAM amount for BCM958525XMC board
ARM: dts: NSP: Specify RAM amount for BCM958625K board
ARM: dts: NSP: Enable SATA and add i2c devices on XMC
ARM: dts: NSP: Enable SATA on bcm958625hr
ARM: dts: NSP: Correct RAM amount for BCM958625HR board
ARM: dts: NSP: Add PWM Support to DT
ARM: BCM5301X: Specify PHY of USB 2.0 in DT
ARM: dts: NSP: Add BCM958625HR switch ports
ARM: dts: NSP: Add Switch Register Access Block node
...
Jamie Lentin [Sat, 6 Aug 2016 10:10:13 +0000 (11:10 +0100)]
ARM: dts: orion5x: Configure WNR854T ethernet PHY LEDs
The default PHY configuration disables most of the LEDs. The following
configures the ethernet activity LEDs as Netgear intended.
[gregory.clement@free-electrons.com: fix commit title]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Jamie Lentin [Wed, 14 Sep 2016 14:47:26 +0000 (16:47 +0200)]
ARM: dts: orion5x: Add description for Netgear WNR854T
This is a router based on the mv88f5181 chipset.
http://www.netgear.com/support/product/WNR854T.aspx
http://wiki.openwrt.org/toh/netgear/wnr854t
[gregory.clement@free-electrons.com:
- extract dt part from "arm: orion5x: Add DT-based support for Netgear
WNR854T"
- squashed "arm: orion5x: Alias uart0 to serial0 for all orion5x" into
this commit and move serial0 alias from dtsi to dts]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Jamie Lentin [Thu, 19 May 2016 21:43:36 +0000 (22:43 +0100)]
ARM: dts: arm: orion5x: Add DT include for mv88f5181
Common definitions for the SoC for board definitions to use.
[gregory.clement@free-electrons.com: fix commit title]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Jamie Lentin [Thu, 19 May 2016 21:36:29 +0000 (22:36 +0100)]
dt-bindings: arm: add DT binding for Marvell Orion5x SoC family
Copy the format for kirkwood/dove to orion5x
[gregory.clement@free-electrons.com: fix commit title]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Jamie Lentin [Thu, 19 May 2016 21:34:03 +0000 (22:34 +0100)]
ARM: dts: orion5x: Add required properties for orion-wdt to DT node
orion-wdt refuses to start without these properties defined, so lift
definitions out of kirkwood/dove.dtsi
[gregory.clement@free-electrons.com: fix commit title]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Baruch Siach [Mon, 5 Sep 2016 19:00:10 +0000 (22:00 +0300)]
dt-binding: mrvl-gpio: remove orion-gpio description
The Orion GPIO controller binding description in mrvl-gpio.txt is obsolete, and
duplicates the description in gpio-mvebu.txt.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Peter Griffin [Mon, 5 Sep 2016 13:16:00 +0000 (15:16 +0200)]
ARM: DT: STi: stihxxx-b2120: Add DT nodes for STi audio card
This patch enables the uniperif players 2 & 3 for b2120 boards
and also adds the "simple-audio-card" device node to interconnect
the SoC sound device and the codec.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Peter Griffin [Mon, 5 Sep 2016 13:16:00 +0000 (15:16 +0200)]
ARM: STi: DT: STiH407: Add uniperif reader dt nodes
This patch adds the DT node for the uniperif reader
IP block found on STiH407 family silicon.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Peter Griffin [Mon, 5 Sep 2016 13:16:00 +0000 (15:16 +0200)]
ARM: STi: DT: STiH407: Add uniperif player dt nodes
This patch adds the DT nodes for the uniperif player
IP blocks found on STiH407 family silicon.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Peter Griffin [Mon, 5 Sep 2016 13:16:00 +0000 (15:16 +0200)]
ARM: STi: DT: STiH407: Add sti-sasg-codec dt node
This patch adds the dt node for the internal audio
codec IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Peter Griffin [Mon, 5 Sep 2016 13:16:00 +0000 (15:16 +0200)]
ARM: DT: STiH407: Add spdif_out pinctrl config
This patch adds the pinctrl config for the spidf out
pins used by the sasg codec IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Peter Griffin [Mon, 5 Sep 2016 13:16:00 +0000 (15:16 +0200)]
ARM: DT: STiH407: Add i2s_in pinctrl configuration
This patch adds the pinctrl config for the i2s_in pins
used by the uniperif reader IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Peter Griffin [Mon, 5 Sep 2016 13:16:00 +0000 (15:16 +0200)]
ARM: DT: STiH407: Add i2s_out pinctrl configuration
This patch adds the pinctrl config for the i2s_out pins
used by the uniperif player IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Peter Griffin [Mon, 5 Sep 2016 13:16:00 +0000 (15:16 +0200)]
ARM: STi: DT: STiH407: Add FDMA driver dt nodes.
These nodes are required to get the fdma driver working
on STiH407 based silicon.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Arnd Bergmann [Tue, 13 Sep 2016 15:43:48 +0000 (17:43 +0200)]
Merge tag 'clcd-nomadik' of git://git./linux/kernel/git/linusw/linux-nomadik into next/dt
Pull "CLCD graphics on the Nomadik NHK15" from Linus Walleij:
* tag 'clcd-nomadik' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: add the CLCD LCD display to the NHK15
ARM: dts: add PMU to the NHK15 device tree
ARM: nomadik: select MFD_SYSCON
dt-bindings: Add TPO TPG110 binding
dt-bindings: add vendor TPO
ARM: dts: add STMPE PWM to the NHK15 device tree
Arnd Bergmann [Tue, 13 Sep 2016 15:42:20 +0000 (17:42 +0200)]
Merge tag 'imx-dt-4.9' of git://git./linux/kernel/git/shawnguo/linux into next/dt
Pull "i.MX device tree changes for 4.9" from Shawn Guo:
- Add SoC support for i.MX7 Solo which is a reduced version of i.MX7
Dual.
- New board support: Gateworks Ventana i.MX6Q/DL GW553x, Inverse Path
i.MX53 USB armory, i.MX6Q/DL TS-4900 from Technologic Systems,
i.MX6UL GEA M6UL modules from Engicam, i.MX7 Solo Warp7 board.
- Add DMA and IPU CSI devices for i.MX53 SoC support.
- Refine i.MX7 Dual SoC DTS as a preparation of i.MX7 Solo support.
- Use of_graph dt nodes to describe the panel for vf610-colibri and
ls1021a-twr boards.
- Add gpio-ranges property to i.MX6 GPIO controllers, which will be
useful when GPIO driver is changed to request pad configuration as
GPIO function.
- Random device additions or small changes for various board support.
* tag 'imx-dt-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (41 commits)
ARM: dts: add gpio-ranges property to iMX GPIO controllers
ARM: dts: imx35: add iim module to imx35.dtsi
ARM: dts: vf610-colibri: use of_graph dt nodes to describe the panel
ARM: dts: ls1021a: Add of_graph dt nodes to describe the panel
ARM: dts: imx53: add support for USB armory board
devicetree: Add vendor prefix for Inverse Path
ARM: dts: imx7s-warp: Add Bluetooth support
ARM: dts: imx7s-warp: Add User Button support
ARM: dts: imx7s-warp: Enable I2C2 device support
ARM: dts: imx6ul-geam: Add Engicam IMX6UL GEA M6UL initial support
ARM: dts: imx6ul iomuxc syscon is compatible to imx6q
ARM: dts: imx7-colibri: add Audio support
ARM: dts: imx7-colibri: add basic supply regulators
ARM: dts: imx7-colibri: move SD-card to module level
ARM: dts: imx6sx: Add GPU bindings
ARM: dts: imx7s-warp: Let the codec control MCLK pinctrl
ARM: dts: imx6ul-pico-hobbit: Use WDOG_B pin reset
ARM: dts: imx6q-bx50v3: configure unused pca953x pins
ARM: dts: imx6sx: document SION necessity of ENET1_REF_CLK1
ARM: dts: imx7s-warp: Use WDOG_B pin reset
...
Arnd Bergmann [Tue, 13 Sep 2016 15:41:15 +0000 (17:41 +0200)]
Merge tag 'realview-dts-split' of git://git./linux/kernel/git/linusw/linux-integrator into next/dt
Pull "RealView DTS file fixup and split" from Linus Walleij:
Fix the ethernet issue on revision D of the RealView EB
Split the DTS files in per-revision variants
* tag 'realview-dts-split' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: add RealView EB rev D A9 MPCore variant
ARM: dts: split RealView EB 11MPCore variants
ARM: dts: add device tree for the RealView EB Rev D
ARM: dts: fix RealView EB SMSC ethernet version
Arnd Bergmann [Tue, 13 Sep 2016 15:40:17 +0000 (17:40 +0200)]
Merge tag 'tegra-for-4.9-arm-dt' of git://git./linux/kernel/git/tegra/linux into next/dt
Pull "ARM: tegra: Device tree changes for v4.9-rc1" from Thierry Reding:
Contains a couple of cleanups for Tegra114 device trees.
* tag 'tegra-for-4.9-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Correct polarity for Tegra114 PMIC interrupt
ARM: tegra: Fix Tegra114 USB compatible values
Arnd Bergmann [Tue, 13 Sep 2016 15:38:34 +0000 (17:38 +0200)]
Merge tag 'v4.9-rockchip-dts32-1' of git://git./linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "Rockchip dts32 changes for 4.9" from Heiko Stübner:
32bit Rockchip devicetree changes containing two new rk3288 boards (Fennec
and Firefly-reload), display support for the rk3288-evb, support for the
recently added firmware reboot-flag support and some housekeeping cleanups.
* tag 'v4.9-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add sensor-supplies on PopMetal-RK3288 board
ARM: dts: rockchip: fix L3G4200D i2c address on PopMetal-RK3288 board
ARM: dts: rockchip: enable usbotg for Popemtal-rk3288 board
ARM: dts: rockchip: add missing regulators for firefly reload board
ARM: dts: rockchip: remove excess sd properties from firefly reload
ARM: dts: rockchip: add syscon-reboot-mode DT node
soc: rockchip: add reboot-mode header
ARM: dts: rockchip: move rk3288 usbphy under the GRF node
ARM: dts: rockchip: add rk3288-firefly-reload
ARM: dts: rockchip: add dts for RK3288-Fennec boards
ARM: dts: rockchip: add the panel power supply for rk3288-evb board with rk808 pmu
ARM: dts: rockchip: add the panel power supply for rk3288-evb board with act8846 pmu
ARM: dts: rockchip: add eDP/panel display device nodes for rk3288-evb
Arnd Bergmann [Tue, 13 Sep 2016 15:36:04 +0000 (17:36 +0200)]
Merge tag 'sunxi-dt-for-4.9' of https://git./linux/kernel/git/mripard/linux into next/dt
Pull "Allwinner DT changes for 4.9" from Maxime Ripard:
Business as usual on our side, with a mix of new boards and new IPs enabled
on boards:
- Support for the GPIO found on the AXP PMIC
- ESP8089 on the relevant boards
- More boards converted to the reference design and q8 designs
- New boards: Orange Pi PC Plus, Orange Pi 2, Orange Pi Plus 2E, Orange
Pi Lite, Olimex A33-Olinuxino, Empire Electronix M712, inet-d978_rev2,
Nano Pi Neo
* tag 'sunxi-dt-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (31 commits)
devicetree: Add vendor prefix for FriendlyARM
ARM: dts: sun8i: Add dts file for the NanoPi NEO SBC
ARM: dts: sun8i-q8-common: Add support for SDIO wifi controllers
ARM: dts: sun8i: Add dts file for the Orange Pi Plus2E SBC
ARM: dts: sun8i: Orange Pi Plus dts is for the Plus and Plus 2
ARM: dts: sun8i: Add PWM controller node in H3
ARM: dts: sun8i: Add dts file for inet-d978_rev2 tablets
ARM: dts: sun9i: Add missing #interrupt-cells to R_PIO pinctrl device node
ARM: dts: sun8i: Rename reference-design-tablet touchscreen node
ARM: dts: sun5i: Add dts file for the Empire Electronix M712 tablet
ARM: dts: sun5i: Convert inet-98v-rev2 dts to use reference-design-tablet.dtsi
ARM: dts: sun4i: Disable ohci1 on ba10-tv-box
ARM: dts: sun8i: Add dt node for esp8089 wifi chip on polaroid-mid2809
ARM: dts: sun8i: Add dt node for esp8089 wifi chip on polaroid-mid2407
ARM: dts: sun8i: add NAND controller node for A23/A33
ARM: dts: sun6i: Add new dts file for tablets using the inet-q972 PCB
ARM: dts: sun6i: Add sun6i-reference-design-tablet.dtsi
ARM: dts: sun6i: colorfly-e708-q1: Remove unused mma8452_int_e708_q1 node
ARM: dts: sun9i: Switch to the AC100 RTC clock outputs for osc32k
ARM: dts: sun9i: cubieboard4: Add device node for AC100
...
Arnd Bergmann [Tue, 13 Sep 2016 15:34:49 +0000 (17:34 +0200)]
Merge tag 'renesas-dt2-for-v4.9' of git://git./linux/kernel/git/horms/renesas into next/dt
Pull "Second Round of Renesas ARM Based SoC DT Updates for v4.9" from Simon Horman:
Fixes (for v4.9):
* Correct PWM clock parent on r8a7794 SoC
Clean-up:
* Remove obsolete vsp1 properties from r8a779[01] SoCs
New boards:
* Add r8a7792/wheat and r7s72100/rskrza1 boards
Enablement:
* Enable LEDs, DU, SDHI on r8a7792/blanche board
* Enable MMCIF and SDHI on r8a7794/alt board
* Add SPI and VSP1 to r8a7792 SoC
* Add ethernet to r7s72100 SoC
* tag 'renesas-dt2-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (26 commits)
ARM: dts: wheat: add support for tactile switches
ARM: dts: wheat: add QSPI support
ARM: dts: r8a7792: add QSPI support
ARM: dts: r8a7792: add QSPI clock
ARM: dts: wheat: add SDHI0 support
ARM: dts: wheat: add CAN support
ARM: dts: r8a7794: fix PWM clock parent
ARM: dts: rskrza1: add ethernet DT support
ARM: dts: r7s72100: add ethernet to device tree
ARM: dts: r7s72100: add ethernet clock to device tree
ARM: dts: rskrza1: initial device tree
ARM: dts: Add RSKRZA1 DT bindings documentation
ARM: dts: wheat: add Ethernet support
ARM: dts: wheat: initial device tree
ARM: dts: document Wheat board
ARM: dts: blanche: add support for general purpose LEDs
ARM: dts: r8a7792: add VSP1V support
ARM: dts: r8a7792: add VSP1V clocks
ARM: dts: blanche: add DU support
ARM: dts: blanche: add SDHI0 support
...
Arnd Bergmann [Tue, 13 Sep 2016 15:32:51 +0000 (17:32 +0200)]
Merge tag 'lpc18xx_dts_for_4.9_part2' of https://github.com/manabian/linux-lpc into next/dt
Pull "Device Tree clean up for LPC18xx platform" from Joachim Eastwood:
* Removal of skeleton.dtsi from the common armv7-m dtsi together
with lpc18xx and efm32 platforms.
* Fix for unit address warnings from the dtc on lpc18xx/efm32.
That is made possible with skeleton.dtsi gone.
* tag 'lpc18xx_dts_for_4.9_part2' of https://github.com/manabian/linux-lpc:
ARM: dts: efm32: remove skeleton.dtsi include and fix unit address warnings
ARM: dts: lpc18xx: remove skeleton.dtsi include and fix unit address warnings
ARM: dts: armv7-m: remove skeleton.dtsi include
Arnd Bergmann [Tue, 13 Sep 2016 15:31:16 +0000 (17:31 +0200)]
Merge tag 'mvebu-dt-4.9-1' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt for 4.9 (part 1)" from Gregory CLEMENT:
- update for Armada XP/38x allowing using direct access SPI
- various improvement for Armada 39x platforms
- add pinctrl information for NANd on Armada 38x
- fix the kirkwood based Openblock A6 external GPIO pins
* tag 'mvebu-dt-4.9-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: mvebu: fix reference to a390 spi controller
ARM: dts: armada-38x: Add NAND pinctrl information
ARM: dts: kirkwood: Fix Openblock A6 external GPIO pins
ARM: dts: mvebu: armada-395-gp: add support for the Armada 395 GP Board
ARM: dts: mvebu: armada-390-db: add support for the Armada 390 DB board
ARM: dts: mvebu: armada-398-db: enable supported usb interfaces
ARM: dts: mvebu: armada-398: update the dtsi about missing interfaces
ARM: dts: mvebu: armada-395: add support for the Armada 395 SoC family
ARM: dts: mvebu: armada-39x: enable rtc for all Armada-39x SoCs
ARM: dts: mvebu: armada-39x: add missing nodes describing GPIO's
ARM: dts: mvebu: armada-39x: enable watchdog for all Armada-39x SoCs
ARM: dts: mvebu: armada-39x: enable the thermal sensor in Armada-39x SoCs
ARM: dts: mvebu: armada-39x: enable PMU, CA9 SoC Controller and Coherency fabric
ARM: dts: mvebu: armada-39x: update the SDHCI node on Armada 39x
ARM: dts: mvebu: armada-390: add missing compatibility string and bracket
ARM: dts: mvebu: a385-db-ap: add default partition description for NAND
ARM: dts: mvebu: a385-db-ap: enable USB (orion-ehci) port
ARM: dts: mvebu: armada-370-xp: Add MBus mappings for all SPI devices
ARM: dts: mvebu: A37x/XP/38x/39x: Move SPI controller nodes into 'soc' node
ARM: dts: mvebu: Add SPI1 pinctrl defines for Armada XP
Arnd Bergmann [Tue, 13 Sep 2016 15:29:08 +0000 (17:29 +0200)]
Merge tag 'qcom-dts-for-4.9' of git://git./linux/kernel/git/agross/linux into next/dt
Pull "Qualcomm Device Tree Changes for v4.9" from Andy Gross:
* Rework dr_mode on APQ8064 and Nexus7
* Add MSM8974 BLSP1 UART1 port
* Add AP148 SATA mapping
* Add support for LG Nexus 5 (Hammerhead)
* Fixup MSM8660/MSM8064 SPMI/MPP IRQs
* Add Nexus7 IMEM/reboot reason
* Add Honami touchscreen support
* Add TSENS support on MSM8974, APQ8064, and APQ8084
* Add APQ8060 Dragonboard PM8058 LEDs
* Rework VPH PWR REG for MSM8974
* tag 'qcom-dts-for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: dts: msm8974: Move vreg_boost node from the honami to msm8974
ARM: dts: qcom: msm8974: Add fixed regulator node for vph-pwr-reg
ARM: dts: add PM8058 LEDs to the APQ8060 Dragonboard
arm: dts: apq8084: Add thermal zones, tsens and qfprom nodes
arm: dts: apq8064: Add thermal zones, tsens and qfprom nodes
arm: dts: msm8974: Add thermal zones, tsens and qfprom nodes
ARM: dts: msm8974: honami: Add touchscreen
device-tree: nexus7: Add IMEM syscon and reboot reason support
ARM: dts: MSM8660 remove flags from SPMI/MPP IRQs
ARM: dts: MSM8064 remove flags from SPMI/MPP IRQs
ARM: dts: msm8974-hammerhead: Introduce gpio-keys nodes
ARM: dts: msm8974-hammerhead: Add regulator nodes for hammerhead
ARM: dts: qcom: Add initial DTS for LG Nexus 5 Phone
ipq8064: dts: force AP148 SATA port mapping
ARM: dts: msm8974: Add nodes for blsp1_uart1 serial port
device-tree: aqp8064.dtsi: Remove usb phy dr_mode = "host"
device-tree: nexus7: Set phy mode to otg instead of host
Mark Rutland [Fri, 2 Sep 2016 16:34:50 +0000 (17:34 +0100)]
ARM: dts: explicitly mark skeleton.dtsi as deprecated
As noted in commit
3ebee5a2e141496b ("arm64: dts: kill skeleton.dtsi"),
there are a number of problems with skeleton.dtsi, and it would be
prefereable to remove it entirely. As there are a large number of
existing users, fixing these up will take a while.
This patch adds a note to arm's skeleton.dtsi noting that this is the
case, to make this more obvious and hopefully minimize new uptake of
skeleton.dtsi in the mean time.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 13 Sep 2016 15:24:24 +0000 (17:24 +0200)]
Merge tag 'sti-dt-for-v4.9-1' of git://git./linux/kernel/git/pchotard/sti into next/dt
Pull "STi dts fixes and new STi 96board support" from Patrice Chotard:
Add thermal node for STiH407 family boards
Add specific nodes for STMicroelectronics 96Board
Add new B2260 STi board file = 96Board
Fix ahci issue on STiH407 family
Fix debugfs/pinctrl kernel warning
Update gpio-cells and gpio specifier
* tag 'sti-dt-for-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: STiH41x-b2020: Update gpio specifier
ARM: dts: STiH418-B2199: Update gpio specifier
ARM: dts: STiH407-pinctrl: Update gpio-cells to 2
ARM: dts: STi: Introduce B2260 board
ARM: dts: STiH407-family: Add ports-implemented property in sata nodes
ARM: dts: STiH407-pinctrl: Add pinctrl_rgmii1_mdio_1 node
ARM: dts: STiH407: Move non-removable property to board file
ARM: dts: STiH407-pinctrl: Add i2c2_alt2_1 node
ARM: dts: STiH410: Add thermal node
ARM: dts: STiH407: Move pio20 node to fix kernel warning
Arnd Bergmann [Tue, 13 Sep 2016 14:27:42 +0000 (16:27 +0200)]
Merge tag 'omap-for-v4.9/dt-pt1-signed' of git://git./linux/kernel/git/tmlind/linux-omap into next/dt
Merge "DTS related changes for omaps for v4.9 merge window" from Tony Lindgren:
- Update elm phandle for am335x
- Fix overo NAND gpmc ranges, this has always been broken so it can
wait for the merge window
- Fix NAND and use NAND ready pin for logicpd gpmc, this can wait too
as it's been using the older configration since the dts got added
- A series of dtc warning fixes for unit names
- Keep dcdc3, 5 and 6 enabled during suspend on am347x boards
- Disable DDR regulator during rtc-only/poweroff mode for am437x boards
- Remove redundant regulator compatibles for am437x boards
- Increas QSPI max frequency for dra7 boards
- Enable QSPI for am57xx-idk-common
- Enable am335x-wega audio support
- Workaround for i845 for dra7
- Update binding for logicpd boards
- Add gpio-decoder nodes for am335x-icev2 board
- Add linux,pci-domain property for dra7
- Fix dra7 clock data gmac_gmii_ref_clk_div and related clock tree
entries, these can wait for merge window as Ethernet works on dra7
- A series of changes to drop skeleton.dtsi because of dtc warnings
* tag 'omap-for-v4.9/dt-pt1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (54 commits)
ARM: dts: dra7: Add missing unit name to memory nodes
ARM: dts: dra62x: Add missing unit name to memory nodes
ARM: dts: dm8168: Add missing unit name to memory nodes
ARM: dts: dm8148: Add missing unit name to memory nodes
ARM: dts: am572x: Add missing unit name to memory nodes
ARM: dts: am4372: Add missing unit name to memory nodes
ARM: dts: am3517: Add missing unit name to memory nodes
ARM: dts: am335x: Add missing unit name to memory nodes
ARM: dts: omap5: Add missing unit name to memory nodes
ARM: dts: omap4: Add missing unit name to memory nodes
ARM: dts: omap3: Add missing unit name to memory nodes
ARM: dts: omap2: Add missing unit name to memory nodes
ARM: dts: am4372: Remove skeleton.dtsi usage
ARM: dts: dra7: Remove skeleton.dtsi usage
ARM: dts: dm816x: Remove skeleton.dtsi usage
ARM: dts: dm814x: Remove skeleton.dtsi usage
ARM: dts: am33xx: Remove skeleton.dtsi usage
ARM: dts: omap5: Remove skeleton.dtsi usage
ARM: dts: omap4: Remove skeleton.dtsi usage
ARM: dts: omap3: Remove skeleton.dtsi usage
...
Arnd Bergmann [Tue, 13 Sep 2016 14:21:02 +0000 (16:21 +0200)]
Merge tag 'keystone_dts_for_4.9' of git://git./linux/kernel/git/ssantosh/linux-keystone into next/dt
Merge "ARM: dts: Keystone DTS for 4.9" from Santosh Shilimkar
Add K2G nodes for GPIO, IRQ and Message Manager
* tag 'keystone_dts_for_4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone-k2g: Add Message Manager node
ARM: dts: keystone-k2g: Add DSP GPIO controller node
ARM: dts: keystone-k2g: Add keystone IRQ controller node
ARM: dts: keystone-k2g: Add device state controller node
ARM: dts: keystone: specify usb mode explicitly
Arnd Bergmann [Tue, 13 Sep 2016 14:11:51 +0000 (16:11 +0200)]
Merge tag 'uniphier-dt-v4.9' of git://git./linux/kernel/git/masahiroy/linux-uniphier into next/dt
Merge "UniPhier ARM SoC DT updates for v4.9" from Masahiro Yamada:
* Match DT names other projects and documents
* Switch over to PSCI
* Use clock/reset drivers
* Misc
* tag 'uniphier-dt-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: add specific compatible to SoC-Glue node
ARM: dts: uniphier: use clock/reset controllers
ARM: dts: uniphier: switch over to PSCI
ARM: dts: uniphier: match DT names to other projects and documents
ARM: dts: uniphier: remove a whitespace after tabs
Arnd Bergmann [Tue, 13 Sep 2016 14:09:10 +0000 (16:09 +0200)]
Merge tag 'samsung-dt-4.9' of git://git./linux/kernel/git/krzk/linux into next/dt
Merge "Samsung DeviceTree update for v4.9" from Krzysztof Kozlowski:
1. Set chosen serial bitrate which allows proper serial output when
bootloader does pass all the data in command line.
2. Cleanup.
* tag 'samsung-dt-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Use 'hpd-gpios' instead of 'hpd-gpio'
ARM: dts: exynos: Use stdout non-deprecated property and add serial options to Odroid XU/XU3/XU4
Arnd Bergmann [Tue, 13 Sep 2016 14:06:41 +0000 (16:06 +0200)]
Merge tag 'lpc18xx_dts_for_4.9' of https://github.com/manabian/linux-lpc into next/dt
Merge "Device Tree additions for LPC18xx platform" from Joachim Eastwood:
Small fix for the compatible string for the NXP SE97 I2C chip on the
Hitex Eval board from Guenter and a couple of additional DT properties
for the DWMAC that is need for correct operation.
* tag 'lpc18xx_dts_for_4.9' of https://github.com/manabian/linux-lpc:
ARM: dts: lpc18xx: configure dwmac properly
ARM: dts: lpc4350-hitex-eval: fix binding for SE97 i2c device
Lars Persson [Tue, 23 Aug 2016 14:00:52 +0000 (16:00 +0200)]
ARM: dts: artpec: set irq affinity on pmu interrupts
The irq affinity is required for pmu interrupts.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Lars Persson [Tue, 23 Aug 2016 14:00:51 +0000 (16:00 +0200)]
ARM: dts: artpec: use optimized pl310 settings
Use the cache settings that were determined to give best performance
on artpec-6 typical workloads.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Lars Persson [Tue, 23 Aug 2016 14:00:50 +0000 (16:00 +0200)]
ARM: dts: artpec: use clock binding header
Use defines from the clock binding header as clock indexes.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 13 Sep 2016 14:01:12 +0000 (16:01 +0200)]
Merge tag 'renesas-dt-for-v4.9' of git://git./linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v4.9" from Simon Horman:
* Add DU, VIN, I2C, SDHI, EtherAVB, GPIO support to r8a7792
* Enable CAN0 on r8a7792/blanche
* Enable sound on r8a7794/silk
* Correct SDHI register size on r8a7794
* tag 'renesas-dt-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (26 commits)
ARM: dts: r8a7792: add DU support
ARM: dts: r8a7792: add DU clocks
ARM: dts: r8a7792: fix misindented line
ARM: dts: silk: add sound support
ARM: dts: r8a7794: add sound support
ARM: dts: r8a7794: add Audio-DMAC support
ARM: dts: r8a7794: add MSTP10 clocks
ARM: dts: r8a7794: add MSTP5 clocks
ARM: dts: r8a7794: add audio clocks
ARM: dts: r8a7792: add VIN support
ARM: dts: r8a7792: add VIN clocks
ARM: dts: r8a7792: add I2C support
ARM: dts: r8a7792: add I2C clocks
ARM: dts: r8a7792: add SDHI support
ARM: dts: r8a7792: add SD clocks
ARM: dts: r8a7794: Correct SDHI register size
ARM: dts: blanche: add CAN0 support
ARM: dts: r8a7792: add CAN support
ARM: dts: r8a7792: add CAN clocks
ARM: dts: r8a7792: add EtherAVB support
...
Linus Walleij [Wed, 27 Jan 2016 21:03:23 +0000 (22:03 +0100)]
ARM: dts: add the CLCD LCD display to the NHK15
This adds the TPG110 TDO43MTEA2 24-bit RGB LCD panel and sets
up the Nomadik device tree to activate the CLCD and connect it
to this panel.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Sun, 10 Jan 2016 21:32:43 +0000 (22:32 +0100)]
ARM: dts: add PMU to the NHK15 device tree
The so-called Nomadik Power Mangament Unit is actually a set
of some power management registers and some miscellaneous
system control stuff like muxing of entire hardware units.
Add this as a system controller.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Sun, 10 Jan 2016 21:34:07 +0000 (22:34 +0100)]
ARM: nomadik: select MFD_SYSCON
Since the Power Management Unit is using syscon to access a
set of necessary hardware muxing, let's select MFD_SYSCON for
the Nomadik subarchitecture.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Wed, 27 Jan 2016 21:35:43 +0000 (22:35 +0100)]
dt-bindings: Add TPO TPG110 binding
This adds device tree bindings for the TPO TPG110 panel found
mounted in the Nomadik NHK8815.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Sat, 9 Jan 2016 22:09:21 +0000 (23:09 +0100)]
dt-bindings: add vendor TPO
TPO was a merger on June 5 2006 of Toppoly Optoelectronics and
Philips Mobile Display Systems. They manufactured small and medium
mobile displays.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Wed, 10 Feb 2016 08:34:32 +0000 (09:34 +0100)]
ARM: dts: add STMPE PWM to the NHK15 device tree
This adds the STMPE PWM to the NHK15 device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Thu, 8 Sep 2016 20:50:39 +0000 (22:50 +0200)]
ARM: dts: add RealView EB rev D A9 MPCore variant
The Cortex A9 MPCore tile can be mounted on top of the revision
D variant of the RealView EB, so create another variant of the
DTS file for this.
arm-realview-eb-a9mp = mounted on pre-revision D baseboard
arm-realview-eb-a9mp-bbrevd = mounted on the revision D baseboard
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Thu, 8 Sep 2016 15:00:45 +0000 (17:00 +0200)]
ARM: dts: split RealView EB 11MPCore variants
There used to be two versions of the RealView EB 11MPCore:
- arm-realview-eb-11mp.dts: the most common variant supported by
QEMU with the revision C core tile
- arm-realview-eb-revb.dts: for the variant with the elder revision
B core tile.
As it turns out that there are also a few variants of the
baseboard, unrelated to the coretile, and that these can of
course be mounted on top of each other in all permutations, we
create:
- arm-realview-eb-11mp.dts: the most common variant supported by
QEMU with the pre-revision D baseboard and the revision C core
tile.
- arm-realview-eb-11mp-bbrevd.dts: the revision D baseboard
with the common revision C core tile.
- arm-realview-eb-11mp-ctrevb.dts: the pre-revision D baseboard
with the revision B core tile.
- arm-realview-eb-11mp-bbrevd-ctrevb.dts: the revision D baseboard
with the revision B core time.
Or as a table:
| Core tile: C | Core tile: B
-----------+----------------------------+-----------------------------------
Baseboard: | |
pre-D |arm-realvie-eb-11mp | arm-realview-eb-11mp-ctrevb
-----------+----------------------------+-----------------------------------
Baseboard: | |
D |arm-realview-eb-11mp-bbrevd | arm-realview-eb-11mp-bbrevd-ctrevb
-----------+----------------------------+-----------------------------------
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Thu, 8 Sep 2016 09:17:14 +0000 (11:17 +0200)]
ARM: dts: add device tree for the RealView EB Rev D
The RealView EB baseboard revision D is a special case as it appears
to be undocumented in ARM official documents, while the Linux kernel
still contains special code for handling it.
commit
be4f3c8691492934c8ee03dbecb3a3a865ac6cd6
"Add RealView/EB support for the LAN9118 Ethernet chip"
adds support for the SMSC LAN9118 chip used on the D revision of
the baseboard, but no other traces of hardware deviations for this
variant can be found.
This creates a separate top-level .dts file especially for this
board version, so that it gets registered with the right type
of ethernet controller. The ethernet controller modifications
are then put into a separate .dtsi file so it can be overlaid
on other EB variants using the revision D baseboard.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Thu, 8 Sep 2016 08:48:38 +0000 (10:48 +0200)]
ARM: dts: fix RealView EB SMSC ethernet version
The ethernet version in the earlier RealView EB variants is
LAN91C111 and not LAN9118 according to ARM DUI 0303E
"RealView Emulation Baseboard User Guide" page 3-57.
Make sure that this is used for the base variant of the board.
As the DT bindings for LAN91C111 does not specify any power
supplies, these need to be deleted from the DTS file.
Fixes:
2440d29d2ae2 ("ARM: dts: realview: support all the RealView EB board variants")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Jean-Christophe Trotin [Mon, 25 Jul 2016 07:57:30 +0000 (09:57 +0200)]
ARM: dts: STiH410: Add hva dt nodes
Add the hva (multi-format video encoder for STMicroelectronics SoC)
dt nodes for the hva device, defining register address, interrupt
and clock.
Signed-off-by: Jean-Christophe TROTIN <jean-christophe.trotin@st.com>
Vladimir Zapolskiy [Fri, 9 Sep 2016 02:02:36 +0000 (05:02 +0300)]
ARM: dts: add gpio-ranges property to iMX GPIO controllers
To establish a connection between GPIO controllers and pin multiplexor
controller add gpio-ranges properties to all GPIO controllers found
on iMX50, iMX6Q/D, iMX6DL/S, iMX6SL, iMX6SX, iMX6UL and iMX7D/S
SoCs. The change was done after human parsing of output from
% gawk -n '{ sub(/.*__/, ""); if ($1 ~ "^GPIO") print $1, $2/4}' imxXX-pinfunc.h | sort -n
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Uwe Kleine-König [Thu, 8 Sep 2016 09:28:15 +0000 (11:28 +0200)]
ARM: dts: imx35: add iim module to imx35.dtsi
This is a prerequisite to remove the static mappings for imx35 devicetree
based machines.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Tue, 6 Sep 2016 18:46:57 +0000 (11:46 -0700)]
ARM: dts: vf610-colibri: use of_graph dt nodes to describe the panel
The fsl,panel property is deprecated and we should use the new
of_graph dt bindings to describe the relationship between the DCU
controller and the panel.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Meng Yi [Tue, 6 Sep 2016 09:45:34 +0000 (17:45 +0800)]
ARM: dts: ls1021a: Add of_graph dt nodes to describe the panel
add of_graph dt nodes to describe the panel, and removed
"fsl,panel" property
Signed-off-by: Meng Yi <meng.yi@nxp.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrej Rosano [Mon, 5 Sep 2016 10:11:17 +0000 (12:11 +0200)]
ARM: dts: imx53: add support for USB armory board
Add support for Inverse Path USB armory board, an open source
flash-drive sized computer based on NXP i.MX53 SoC.
https://inversepath.com/usbarmory
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrej Rosano [Mon, 5 Sep 2016 10:11:16 +0000 (12:11 +0200)]
devicetree: Add vendor prefix for Inverse Path
Inverse Path is an information security consulting company:
https://inversepath.com
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Patrice Chotard [Thu, 8 Sep 2016 07:36:19 +0000 (09:36 +0200)]
ARM: dts: STiH410-b2260: add clk_ignore_unused in bootargs
This allows to make the board boot even if clock handling
by all drivers is not properly done.
Reported-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Neil Armstrong [Mon, 22 Aug 2016 15:36:33 +0000 (17:36 +0200)]
ARM: dts: meson8b: Add Meson8b PWM Controller nodes
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Patrice Chotard [Wed, 7 Sep 2016 09:22:57 +0000 (11:22 +0200)]
ARM: dts: STiH410-b2260: add USB3 node
Allow to use the mico USB port which is driven by USB3 IP
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Sergei Shtylyov [Mon, 5 Sep 2016 21:33:05 +0000 (00:33 +0300)]
ARM: dts: wheat: add support for tactile switches
Add support for the tactile switches SW2/3 (on the debug board) as a
virtual keyboard like it was done with the Blanche board).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sergei Shtylyov [Fri, 2 Sep 2016 22:09:26 +0000 (01:09 +0300)]
ARM: dts: wheat: add QSPI support
Define the Wheat board dependent part of the QSPI device node.
Add device nodes for Spansion S25FL512S SPI flash and MTD partitions on it.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Joachim Eastwood [Mon, 29 Aug 2016 21:58:29 +0000 (23:58 +0200)]
ARM: dts: efm32: remove skeleton.dtsi include and fix unit address warnings
Removale of skeleton.dtsi allows us also to fix the following
warning from the dts compiler:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
by adding proper unit addresses to the memory nodes. Also add missing
device_type to the memory node while at it.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Joachim Eastwood [Mon, 29 Aug 2016 21:37:24 +0000 (23:37 +0200)]
ARM: dts: lpc18xx: remove skeleton.dtsi include and fix unit address warnings
Removale of skeleton.dtsi allows us also to fix the following
warning from the dts compiler:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
by adding proper unit addresses to the memory nodes.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Joachim Eastwood [Mon, 29 Aug 2016 21:33:56 +0000 (23:33 +0200)]
ARM: dts: armv7-m: remove skeleton.dtsi include
Remove skeleton.dtsi from the common ARM Cortex-M dtsi. This will allow
us to remove skeleton.dtsi on a per platform basis and get rid of the
unit address warning on the memory nodes without getting duplicate memory
nodes.
See
3ebee5a2e141 ("arm64: dts: kill skeleton.dtsi") for additional
reasons not to use the skeleton.dtsi.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Lee Jones [Tue, 16 Aug 2016 09:34:00 +0000 (11:34 +0200)]
ARM: dts: STiH416: Define the number of PWM Capture channels
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Lee Jones [Tue, 16 Aug 2016 09:34:00 +0000 (11:34 +0200)]
ARM: dts: STiH416: Define PWM Capture clock
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Lee Jones [Tue, 16 Aug 2016 09:34:00 +0000 (11:34 +0200)]
ARM: dts: STiH416: Declare PWM Capture data lines via Pinctrl
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Lee Jones [Tue, 16 Aug 2016 09:34:00 +0000 (11:34 +0200)]
ARM: dts: STiH416: Supply PWM Capture IRQs
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Lee Jones [Tue, 16 Aug 2016 09:34:00 +0000 (11:34 +0200)]
ARM: dts: STiH407: Declare PWM Capture data lines via Pinctrl
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Lee Jones [Tue, 16 Aug 2016 09:34:00 +0000 (11:34 +0200)]
ARM: dts: STiH407: Supply PWM Capture IRQ
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Patrice Chotard [Thu, 4 Aug 2016 09:52:01 +0000 (11:52 +0200)]
ARM: dts: STiH416-b2020e: update gpio specifier
Remove useless gpio-cells
Add second parameter to indicate if gpio is active high
or low.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Patrice Chotard [Thu, 4 Aug 2016 09:50:21 +0000 (11:50 +0200)]
ARM: dts: STiH41x-b2000: update gpio specifier
Remove useless gpio-cells
Add second parameter to indicate if gpio is active high
or low.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Patrice Chotard [Thu, 4 Aug 2016 09:44:32 +0000 (11:44 +0200)]
ARM: dts: STiHxxx-b2120: update gpio specifier
Remove useless gpio-cells
Add second parameter to indicate if gpio is active high
or low.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Patrice Chotard [Thu, 4 Aug 2016 09:51:17 +0000 (11:51 +0200)]
ARM: dts: STiH416-pinctrl: update gpio-cells to 2
This patch allows to use second parameter to the gpio
specifier, which is used to specify whether the gpio is
active high or low.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Patrice Chotard [Thu, 4 Aug 2016 09:52:24 +0000 (11:52 +0200)]
ARM: dts: STiH415-pinctrl: update gpio-cells to 2
This patch allows to use second parameter to the gpio
specifier, which is used to specify whether the gpio is
active high or low.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
James Pettigrew [Mon, 5 Sep 2016 22:15:57 +0000 (08:15 +1000)]
devicetree: Add vendor prefix for FriendlyARM
Guangzhou FriendlyARM Computer Tech Co., Ltd is a Chinese ARM board vendor.
Signed-off-by: James Pettigrew <james@innovum.com.au>
Reviewed-by: Rask Ingemann Lambertsen <ccc94453@vip.cybercity.dk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
James Pettigrew [Mon, 5 Sep 2016 22:15:56 +0000 (08:15 +1000)]
ARM: dts: sun8i: Add dts file for the NanoPi NEO SBC
The NanoPi NEO is a minimal H3 based SBC. It comes with 256/512M RAM, a
micro SD slot, 10/100Mbit ethernet and a single USB-A port.
Signed-off-by: James Pettigrew <james@innovum.com.au>
Reviewed-by: Rask Ingemann Lambertsen <ccc94453@vip.cybercity.dk>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Fri, 26 Aug 2016 14:52:36 +0000 (16:52 +0200)]
ARM: dts: sun8i-q8-common: Add support for SDIO wifi controllers
Most of the sun8i q8 boards have an SDIO wifi controller, on the
variants which use an USB wifi controller, this will result in a
couple of error msg-s in dmesg when proving the sdio bus and
an used mmc controller.
The best way to deal with wifi on this boards really is to simply
let the kernel auto-detect usb or sdio wifi controllers, so we
will just have to live with the few errors in dmesg.
This has been tested on a23 based q8 tablets with ESP8089, RTL8703AS and
RTL8189FTV wifi controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Sergei Shtylyov [Fri, 2 Sep 2016 22:08:45 +0000 (01:08 +0300)]
ARM: dts: r8a7792: add QSPI support
Define the generic R8A7792 part of the QSPI device node.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sergei Shtylyov [Fri, 2 Sep 2016 22:07:28 +0000 (01:07 +0300)]
ARM: dts: r8a7792: add QSPI clock
Describe the QSPI clock in the R8A7792 device tree.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sergei Shtylyov [Tue, 30 Aug 2016 22:24:41 +0000 (01:24 +0300)]
ARM: dts: wheat: add SDHI0 support
Define the Wheat board dependent part of the SDHI0 (connected to the
micro-SD slot) device node along with the necessary voltage regulator.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sergei Shtylyov [Mon, 29 Aug 2016 20:11:26 +0000 (23:11 +0300)]
ARM: dts: wheat: add CAN support
Define the Wheat board dependent part of the CAN0/1 device nodes...
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sergei Shtylyov [Sun, 4 Sep 2016 19:55:37 +0000 (22:55 +0300)]
ARM: dts: r8a7794: fix PWM clock parent
When removing the non-existing thermal clock I forgot to remove its
parent from the node's "clocks" property -- this led to a wrong PWM
clock's parent clock.
Fixes:
2a29f9d6fea8 ("ARM: dts: r8a7794: add MSTP5 clocks")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Chris Brandt [Fri, 2 Sep 2016 01:40:12 +0000 (21:40 -0400)]
ARM: dts: rskrza1: add ethernet DT support
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Chris Brandt [Fri, 2 Sep 2016 01:40:11 +0000 (21:40 -0400)]
ARM: dts: r7s72100: add ethernet to device tree
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Chris Brandt [Fri, 2 Sep 2016 01:40:10 +0000 (21:40 -0400)]
ARM: dts: r7s72100: add ethernet clock to device tree
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>