Sangsu Park [Fri, 16 Mar 2012 06:40:53 +0000 (15:40 +0900)]
ASoC: Samsung: Added to support mono recording
The dma size will be changed by requested number of
channel(mono/stereo) from platform. For mono recording,
channels_min value should be 1.
Signed-off-by: Sangsu Park <sangsu4u.park@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 14 Mar 2012 20:18:49 +0000 (20:18 +0000)]
ASoC: core: Fix obscure leak of runtime array
We're currently not freeing card->rtd in cases where the card is
unregistered before being instantiated - convert it to devm_kzalloc() to
make sure that happens.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Wed, 14 Mar 2012 18:38:28 +0000 (18:38 +0000)]
ASoC: wm8996: Add 44.1kHz support
The WM8996 specification has been updated to specify 44.1kHz as a supported
sample rate. Update the driver to accept this configuration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fabio Estevam [Mon, 12 Mar 2012 22:48:49 +0000 (19:48 -0300)]
ASoC: mx27vis-aic32x4: Convert it to platform driver
Convert mx27vis-aic32x4 to platform driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lars-Peter Clausen [Mon, 5 Mar 2012 13:02:15 +0000 (14:02 +0100)]
ASoC: ep93xx-pcm: Use dmaengine PCM helper functions
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mika Westerberg [Mon, 5 Mar 2012 13:02:14 +0000 (14:02 +0100)]
ASoC: dmaengine_pcm: Reset pointer position when starting a stream
Otherwise a wrong position will be reported after restarting a stream and the
first few samples might be skipped.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Mon, 12 Mar 2012 16:31:50 +0000 (16:31 +0000)]
ASoC: wm8994: Prevent ABBA deadlock with CODEC and accdet mutexes
Currently we can the accdet mutex from within DAPM when updating the device
state which means we take accdet then the CODEC mutex but we also do the
locking the other way around when responding to the jackdet IRQ. Move all
the jackdet use of the CODEC mutex out of the accdet lock to avoid this.
Since all the DAPM interactions depend only on a single threaded IRQ this
is still serialised.
The locking improvements in 3.5 allow a better solution there.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Mon, 12 Mar 2012 10:33:34 +0000 (10:33 +0000)]
ASoC: Revert widget I/O locking for 3.4
The widget locking depends on some of the other locking changes which
are queued up for 3.5 not 3.4 so revert the locking changes and reapply
them in 3.5.
This reverts commit
66bf93212f19548f5ed221356b2d70189cc18254 and
96acc357bedad69fbc94d1b923a960af5a411c6f.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Ashish Chavan [Fri, 9 Mar 2012 08:21:30 +0000 (13:51 +0530)]
ASoC: da7210: Remove extra registers from defaults list
This patch removes following registers from reg map defaults,
- Registers which are currently not used by driver
- Non existing registers
- Volatile registers
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Shawn Guo [Thu, 8 Mar 2012 16:59:46 +0000 (00:59 +0800)]
ASoC: fsl: check property 'compatible' for the machine name
Check /compatible rather than /model to determine the machine name.
The p1022ds older device trees get a different /model from the new
ones, while /compatible is consistent there, so checking /compatible
will save the bother of detecting older p1022ds device trees.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Thu, 8 Mar 2012 17:00:57 +0000 (17:00 +0000)]
ASoC: wm8996: Remove separate output stage enable step
Marginally improve performance during startup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Thu, 8 Mar 2012 15:59:50 +0000 (15:59 +0000)]
ASoC: wm8996: Remove some volatile regisers from the defaults table
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Shawn Guo [Thu, 8 Mar 2012 16:59:40 +0000 (00:59 +0800)]
ASoC: core: missing set_fmt should not be complaint
Not having a DAI link set_fmt operation is perfectly normal and
should not be complaint.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ashish Chavan [Thu, 8 Mar 2012 13:34:56 +0000 (19:04 +0530)]
ASoC: da7210: Update for using I2C regmap
Current DA7210 driver has I2C support using older register cache
methods. This patch updates it for latest regmap framework.
This has been tested on DA7210 EVB with Samsung SMDK6410 board.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Qiao Zhou [Thu, 8 Mar 2012 02:02:36 +0000 (10:02 +0800)]
ASoC: add more sample rate for pxa-ssp
add more sample rate for pxa-ssp, which are supported, such as 32KHz,
64KHz.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fabio Estevam [Wed, 7 Mar 2012 18:19:57 +0000 (15:19 -0300)]
ASoC: imx: imx-audmux: Fix section mismatch
Fix the following section mismatch warning:
WARNING: vmlinux.o(.data+0x35be8): Section mismatch in reference from the variable imx_audmux_driver to the function .init.text:imx_audmux_probe()
The variable imx_audmux_driver references
the function __init imx_audmux_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 6 Mar 2012 23:58:22 +0000 (23:58 +0000)]
ASoC: dapm: Only lock CODEC for I/O if not using regmap
If we do use regmap then regmap will take care of things for us. We
actually already have this check at a higher level for the current
users but this makes sure we do the right thing in the future too if
we need to.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Liam Girdwood [Tue, 6 Mar 2012 18:16:19 +0000 (18:16 +0000)]
ASoC: DAPM: Make sure DAPM widget IO ops hold the component mutex
Currently not all DAPM widget IO ops are holding their component mutex
(codec or platform). Make sure this is now held for DAPM widget IO operations.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Liam Girdwood [Tue, 6 Mar 2012 18:16:18 +0000 (18:16 +0000)]
ASoC: core: Add platform component mutex
Add mutex support for platform IO operations. e.g. can be used
for platform DAPM widget IO ops.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Tue, 6 Mar 2012 19:13:07 +0000 (12:13 -0700)]
ASoC: tegra: Remove unused variable
Fixes the following warning:
sound/soc/tegra/tegra_alc5632.c: In function 'tegra_alc5632_asoc_init':
sound/soc/tegra/tegra_alc5632.c:118:6: warning: unused variable 'ret' [-Wunused-variable]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Liam Girdwood [Tue, 6 Mar 2012 18:13:25 +0000 (18:13 +0000)]
ASoC: dapm: Use dev_warn for debugfs warning message
Remove printk(KERN_WARNING) and use dev_warn() instead.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Takashi Iwai [Tue, 6 Mar 2012 13:04:16 +0000 (14:04 +0100)]
Merge tag 'asoc-3.4' of git://git./linux/kernel/git/broonie/sound into topic/asoc
A few more ASoC updates, the main one is the move of the audmux driver
from arch/arm into sound/soc. There's also some general driver specific
tweaks and fixes.
Richard Zhao [Mon, 5 Mar 2012 14:31:04 +0000 (22:31 +0800)]
ASoC: fsl: add dt support for imx-audmux
It adds device tree probe support for imx-audmux driver.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Tue, 6 Mar 2012 07:06:53 +0000 (15:06 +0800)]
ASoC: Add missing regmap_init_i2c in wm8804_i2c_probe
commit 891271c "ASoC: Convert wm8804 to direct regmap API usage"
only converts wm8804_spi_probe to use regmap_init_spi.
This patch adds missing regmap_init_i2c in wm8804_i2c_probe.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 6 Mar 2012 00:25:28 +0000 (00:25 +0000)]
ASoC: wm8962: Remove defaults for volatile registers
Save a little RAM.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Thu, 23 Feb 2012 21:50:03 +0000 (21:50 +0000)]
ASoC: wm8962: Remove unneeded pm_runtime_set_active()
The default pm_runtime status is enabled which is what we want.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sun, 4 Mar 2012 02:16:01 +0000 (02:16 +0000)]
ASoC: wm8994: Use audio mode for jack detection when system is active
When we are out of system sleep always use audio mode for jack detection
in order to avoid potential performance issues handing off between modes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Shawn Guo [Mon, 5 Mar 2012 14:30:56 +0000 (22:30 +0800)]
ASoC: imx: add an explicit Kconfig option for imx-ssi driver
Currently ASoC:imx uses menuconfig option SND_IMX_SOC selects imx-ssi
driver, and it works because all the machine driver covered by the
menuconfig need to build imx-ssi driver in. However, it will not work
any more if we have a imx based machine driver going into the menuconfig
while working with fsl_ssi driver (sound/soc/fsl/fsl_ssi.c) rather than
imx-ssi one.
The patch adds an explicit Kconfig option SND_SOC_IMX_SSI for imx-ssi
driver, so that it can be selected independently from the menuconfig
option SND_IMX_SOC.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Shawn Guo [Mon, 5 Mar 2012 14:30:55 +0000 (22:30 +0800)]
ASoC: imx: separate imx-pcm bits from imx-ssi driver
Currently the imx-ssi.c[h] accommodates the imx-pcm common bits which
are shared between imx-pcm-dma-mx2 and imx-pcm-fiq drivers. It assumes
that imx-pcm-dma-mx2 and imx-pcm-fiq will always be used together with
imx-ssi driver. However this becomes untrue when we see that driver
sound/soc/fsl/fsl_ssi could possibly work with imx-pcm-dma-mx2 too.
The patch moves the imx-pcm common bits from imx-ssi.c[h] into new
files imx-pcm.c[h], and let imx-pcm-dma-mx2 and imx-pcm-fiq drivers
build it in, so that imx-pcm-dma-mx2 can work with no dependency on
imx-ssi driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Shawn Guo [Mon, 5 Mar 2012 14:30:54 +0000 (22:30 +0800)]
ASoC: imx: rename audmux prefix mxc to imx
It renames the legacy name mxc used in audmux function and macro
to imx.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Shawn Guo [Mon, 5 Mar 2012 14:30:53 +0000 (22:30 +0800)]
ASoC: imx: move audmux driver into sound/soc/imx
As audmux becomes a platform driver and its callers are all ASoC
machine drivers, there is no reason to keep it in arch folder, so
move it to sound/soc/imx.
One bonus point would be those ASoC machine drivers stop including
mach/audmux.h, since it's been moved to sound/soc/imx/imx-audmux.h.
This should be a move to the right direction in terms of single kernel
image goal.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Richard Zhao [Mon, 5 Mar 2012 14:30:52 +0000 (22:30 +0800)]
ARM: imx: convert audmux to a platform driver
It coverts audmux to a platform driver, so that it can be moved into
sound/soc/imx and adopt device tree support later.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Shawn Guo [Mon, 5 Mar 2012 14:30:51 +0000 (22:30 +0800)]
ARM: imx: merge audmux-v1 and audmux-v2
It merges audmux-v1 and audmux-v2 under arch/arm/plat-mxc into one.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Shawn Guo [Mon, 5 Mar 2012 14:30:50 +0000 (22:30 +0800)]
ASoC: imx: move phycore audmux call into ASoC machine driver
It moves phycore audmux configuration call from board file into ASoC
machine driver phycore-ac97 to ease converting audmux into a platform
driver later.
It moves phycore audmux configuration call from board file into ASoC
machine driver phycore-ac97, so that it gets aligned with wm1133-ev1
and mx27vis-aic32x4, and more importantly it will ease the moving of
audmux into sound/soc/imx as a platform driver later.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Shawn Guo [Mon, 5 Mar 2012 14:30:49 +0000 (22:30 +0800)]
ASoC: imx: move eukrea audmux call into ASoC machine driver
It moves eukrea audmux configuration call from board file into ASoC
machine driver eukrea-tlv320, so that it gets aligned wm1133-ev1 and
mx27vis-aic32x4, and more importantly it will ease the moving of audmux
into sound/soc/imx as a platform driver later.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sat, 3 Mar 2012 18:01:01 +0000 (18:01 +0000)]
ASoC: dapm: Show if widgets are forced in debugfs
The information was not otherwise visible.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Takashi Iwai [Mon, 5 Mar 2012 14:07:33 +0000 (15:07 +0100)]
Merge tag 'asoc-3.4' of git://git./linux/kernel/git/broonie/sound into topic/asoc
This has been a very active release for ASoC, as well as the usual raft
of bugfixes and driver updates there's quite a few framework enhancements.
Most are either small or are laying the groundwork for user visible
features (especially dynamic PCM), the most directly visible change is
the dmaengine library. There's also a bunch of regmap API enhancements
pulled into the tree so that either the framework or drivers can take
advantage of the new features.
Changes include:
- Support for widgets not associated with a CODEC, an important part of
the dynamic PCM framework.
- A library factoring out the common code shared by dmaengine based DMA
drivers contributed by Lars-Peter Clausen. This will save a lot of
code and make it much easier to deploy enhancements to dmaengine.
- Support for binary controls, used for providing runtime configuration
of algorithm coefficients.
- A new DAPM widget type for regulator supplies allowing drivers for
devices that can power down unused supplies while active to do without
any per-driver code.
- DAPM widgets for DAIs, initially giving a speed boost for playback
startup and shutdown and also the basis for CODEC<->CODEC DAI link
support.
- Support for specifying the number of significant bits on audio
interfaces, useful for allowing applications to know how much effort to
put into generating data for a larger sample format.
- Conversion of the FSI driver used on some SH processors to DMAEngine.
- New CODEC drivers for Maxim MAX9768 and Wolfson Microelectronics WM2200.
Denis 'GNUtoo' Carikli [Sun, 26 Feb 2012 18:21:53 +0000 (19:21 +0100)]
ASoC: wm8753: fix initialization
Without that fix the wm8753 SPI initialization fails, and then produces
a kernel panic during boot with the following call trace:
Unable to handle kernel paging request at virtual address
37386d9b
[<
c01ccafc>] (regmap_get_val_bytes+0x0/0x14) from [<
c0243dfc>] (snd_soc_codec_set_cache_io+0x9c/0xcc)
[<
c0243dfc>] (snd_soc_codec_set_cache_io+0x9c/0xcc) from [<
c0244a4c>] (wm8753_probe+0x5c/0x1c4)
[<
c0244a4c>] (wm8753_probe+0x5c/0x1c4) from [<
c023bb24>] (soc_probe_codec+0x174/0x284)
[<
c023bb24>] (soc_probe_codec+0x174/0x284) from [<
c023c2c0>] (snd_soc_instantiate_cards+0x68c/0xe28)
[<
c023c2c0>] (snd_soc_instantiate_cards+0x68c/0xe28) from [<
c023d278>] (snd_soc_register_card+0x240/0x2d4)
[<
c023d278>] (snd_soc_register_card+0x240/0x2d4) from [<
c023d330>] (soc_probe+0x24/0x40)
[<
c023d330>] (soc_probe+0x24/0x40) from [<
c01c3900>] (platform_drv_probe+0x14/0x18)
[...]
The commit
d3398ff05907167f463e119421b053ce043741d1
( ASoC: Convert WM8753 to direct regmap API usage ) introduced
the problem.
Thanks to Lars-Peter Clausen for helping me a bit during the debugging.
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Fri, 2 Mar 2012 16:18:30 +0000 (16:18 +0000)]
ASoC: core: Split the union for CODEC/platform in the DAI
There's now core code which falls back to global CODEC operations for
DAI calls that needs to be able to tell if it's dealing with a CPU or
CODEC DAI and given the small number of DAIs in a typical system and
overall memory usage pattern saving a pointer per DAI is really not
worth the effort.
Reported-by: Ian Lartey <ian@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Shawn Guo [Sat, 3 Mar 2012 15:20:00 +0000 (23:20 +0800)]
ASoC: sgtl5000: rename device tree binding document
It moves and renames sgtl5000 device tree binding document to make
it aligned with other codecs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Shawn Guo [Sat, 3 Mar 2012 15:19:48 +0000 (23:19 +0800)]
ASoC: imx: move SND_SOC_AC97_BUS selection down to machine driver
SND_SOC_AC97_BUS is selected to enable the AC97 support in soc-core.
Rather than selecting the option under SND_IMX_SOC, it's better to
leave the selection to individual machine driver which knows if AC97
support is needed or not.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Shawn Guo [Sat, 3 Mar 2012 15:19:49 +0000 (23:19 +0800)]
ASoC: imx: initialize dma_params burstsize just in imx-ssi
It's not necessary for imx-pcm-dma-mx2 to access imx_ssi.dma_params
for burstsize initialization. Instead, it can just be done in imx-ssi
probe function once.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sat, 3 Mar 2012 20:02:49 +0000 (20:02 +0000)]
ASoC: wm8994: Factor out WM1811A detection mode setting
Push everything through one function for active use cases, should be
no practical effect.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sat, 3 Mar 2012 00:10:02 +0000 (00:10 +0000)]
ASoC: wm8994: Don't bother updating the jackdet mode needlessly
If we're not doing jackdet it's not needed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sat, 3 Mar 2012 18:46:36 +0000 (18:46 +0000)]
ASoC: wm8994: Disable JACKDET when disabling detecton
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sat, 3 Mar 2012 18:46:06 +0000 (18:46 +0000)]
ASoC: wm8994: Make sure we sync DAPM on WM8958 detection mode changes
Normally this will have no effect as we set detection up at system startup
before DAPM syncs take effect, this will only be useful if the system
enables and disables detection at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 29 Feb 2012 16:40:08 +0000 (16:40 +0000)]
ASoC: wm_hubs: Disable cache of the DC servo calibration for WM1811
The WM1811 DC servo is able to run much faster than previous devices so
the benefit of skipping calibration is not useful.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sat, 3 Mar 2012 15:33:23 +0000 (15:33 +0000)]
ASoC: wm8994: Suppress noop updates of FLL K
Using snd_soc_write() means we always write to the register even if it
already contains the newly calculated value.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sat, 3 Mar 2012 23:24:39 +0000 (23:24 +0000)]
ASoC: wm8994: Push wm8994 private data allocation out into device probe
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Fri, 2 Mar 2012 13:07:41 +0000 (13:07 +0000)]
ASoC: core: Log a warning when machines use soc-audio
snd_soc_register_card() has been available and strongly preferred since
2.6.38 but we're still seeing new drivers using it and the conversion rate
for older machines has been low. Help address both issues by logging a
warning when the soc-audio device probes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Liam Girdwood [Fri, 2 Mar 2012 16:13:44 +0000 (16:13 +0000)]
ASoC: core: cleanup platform debugfs on probe failure.
Make sure we cleanup the platform debugfs when probe fails.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lars-Peter Clausen [Wed, 22 Feb 2012 09:49:10 +0000 (10:49 +0100)]
ASoC: mxs-pcm: Use dmaengine PCM helper functions
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lars-Peter Clausen [Wed, 22 Feb 2012 09:49:09 +0000 (10:49 +0100)]
ASoC: imx-pcm-dma: Use dmaengine PCM helper functions
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lars-Peter Clausen [Wed, 22 Feb 2012 09:49:08 +0000 (10:49 +0100)]
ASoC: Add dmaengine PCM helper functions
This patch adds a set of functions which are intended to be used when
implementing a dmaengine based sound PCM driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Thu, 1 Mar 2012 16:40:51 +0000 (16:40 +0000)]
ASoC: wm8962: Run the headphone in class G mode when sidetone is enabled
Class W mode with sidetone is not fully supported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Thu, 1 Mar 2012 19:01:43 +0000 (19:01 +0000)]
ASoC: wm8994: Disable debounce of jack detection on inserted jack
Don't debounce jack detection for inserted jacks, giving improved
responsiveness.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Thu, 1 Mar 2012 12:07:15 +0000 (12:07 +0000)]
ASoC: wm8962: Remove register default for PLL2
The initial value can be changed depending on system configuration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jaswinder Singh [Sat, 25 Feb 2012 10:54:36 +0000 (16:24 +0530)]
ASoC: Samsung: Update email id of the author
I moved on from a great employer and the email-id no longer exists.
Update email-id to a personal one, assuming I don't move on from
myself anytime soon. And when I do, people don't get the eulogies
bounced.
Signed-off-by: Jaswinder Singh <jassisinghbrar@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jassi Brar [Sat, 25 Feb 2012 11:12:34 +0000 (16:42 +0530)]
ASoC: Samsung: Merge two identical if-else clauses
Saves two lines and a hell of a lot of embarrassment looking at the code.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 29 Feb 2012 15:26:54 +0000 (15:26 +0000)]
ASoC: wm8994: Remove stub of register access code
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 29 Feb 2012 15:39:56 +0000 (15:39 +0000)]
ASoC: wm_hubs: Bomb out if we can't read back the DC servo result
Should have no practical impact but it's safer than trying to soldier on.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 29 Feb 2012 17:28:39 +0000 (17:28 +0000)]
ASoC: wm8996: Remove stub register cache
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 29 Feb 2012 17:45:12 +0000 (17:45 +0000)]
ASoC: wm8996: Fix /RESET bounce ordering
We want to leave the device out of rather than in reset.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 28 Feb 2012 19:03:37 +0000 (19:03 +0000)]
ASoC: wm8994: Make sure we don't have MICBIAS on during jackdet mode
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Leon Romanovsky [Mon, 27 Feb 2012 19:18:19 +0000 (21:18 +0200)]
ASoC: DT: Update digital microphone binding documentation to PAZ00 board.
This patch updates device tree binding documentation to add digital
microphone to PAZ00 board.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Shawn Guo [Fri, 24 Feb 2012 14:09:38 +0000 (22:09 +0800)]
ASoC: Remove unnecessary -codec from cs4270 driver name
Similar to what commit 1e3ad57 (ASoC: Remove redundant -codec from
WM8776 driver name) does for wm8776 driver, this patch does the same
thing for cs4270 driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Shawn Guo [Fri, 24 Feb 2012 14:09:37 +0000 (22:09 +0800)]
ASoC: fsl: align mpc8610_hpcd with p1022_ds on getting codec node
Align mpc8610_hpcd with p1022_ds on getting codec node by just calling
of_parse_phandle. The bonus point of doing that is we can save
exporting get_node_by_phandle_name() when we consolidate the common
bits between mpc8610_hpcd and p1022_ds into a module, which can be
shared by more machine drivers added later.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Shawn Guo [Fri, 24 Feb 2012 14:09:36 +0000 (22:09 +0800)]
ASoC: fsl: correct get_dma_channel parameter name
The second parameter of function get_dma_channel is actually a property
name rather than a compatible string, so rename it for less confusing.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Mon, 27 Feb 2012 15:24:10 +0000 (15:24 +0000)]
ASoC: wm8753: Convert to devm_kzalloc()
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Paul Gortmaker [Sat, 25 Feb 2012 21:12:30 +0000 (16:12 -0500)]
ASoC: fix trivial build error in mpc5200_dma.c
Add the obvious header to fix this:
sound/soc/fsl/mpc5200_dma.c:301: error: implicit declaration of function 'DMA_BIT_MASK'
sound/soc/fsl/mpc5200_dma.c:301: error: initializer element is not constant
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Shawn Guo [Wed, 22 Feb 2012 08:40:26 +0000 (16:40 +0800)]
ASoC: imx: let SND_MXC_SOC_FIQ select FIQ
CONFIG_FIQ is only needed when CONFIG_SND_MXC_SOC_FIQ is selected to
build imx-pcm-fiq.c, so let SND_MXC_SOC_FIQ select FIQ.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Viresh Kumar [Fri, 24 Feb 2012 10:55:49 +0000 (16:25 +0530)]
ASoC: core: Don't overwrite .poweroff in snd_soc_pm_ops
SET_SYSTEM_SLEEP_PM_OPS writes .poweroff = *_resume once. Then we overwrite it
again explicitly as .poweroff = snd_soc_poweroff. Even though it works, as the
second one overwrites the first one, this is not the correct way. Fix this by
expanding SET_SYSTEM_SLEEP_PM_OPS in our structure.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Thu, 23 Feb 2012 21:49:37 +0000 (21:49 +0000)]
ASoC: wm8962: Convert interrupt handler to direct regmap usage
Avoids potential locking issues with anything that needs the CODEC lock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 22 Feb 2012 20:23:01 +0000 (20:23 +0000)]
ASoC: wm8962: Remove mistakenly committed debug logging
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Fri, 17 Feb 2012 20:14:18 +0000 (12:14 -0800)]
ASoC: ak4104: Convert to direct regmap API usage
Since the cache is currently open coded this is more of a win than for
most devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Mark Brown [Fri, 17 Feb 2012 20:05:51 +0000 (12:05 -0800)]
ASoC: ak4104: Use snd_soc_write() rather than internal write function
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Mark Brown [Fri, 17 Feb 2012 20:04:41 +0000 (12:04 -0800)]
ASoC: ak4104: Use snd_soc_update_bits() for read/modify/write
Don't use the internal I/O functions directly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Lars-Peter Clausen [Wed, 22 Feb 2012 09:49:07 +0000 (10:49 +0100)]
ASoC: mxs-pcm: Request DMA channel early
Request the DMA channel in the PCM open callback instead of the hwparams
callback, this allows us to let open fail if no dma channel is available. This
also fixes a bug where the channel will be requested multiple times if hwparams
is called multiple times.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lars-Peter Clausen [Wed, 22 Feb 2012 09:49:06 +0000 (10:49 +0100)]
ASoC: imx-pcm: Request DMA channel early
Request the DMA channel in the pcm open callback. This allows us to let open
fail if there is no dma channel available.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lars-Peter Clausen [Wed, 22 Feb 2012 09:49:05 +0000 (10:49 +0100)]
ASoC: imx-ssi: Set dma data early
Move the call to snd_soc_dai_set_dma_data from the hw_params callback to the
startup callback. This allows us to use the dma data in the pcm driver's open
callback.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 21 Feb 2012 16:24:00 +0000 (16:24 +0000)]
ASoC: wm8994: Move wm_hubs callback before we start ramping VMID
Allows the generic code to set up for that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Fri, 17 Feb 2012 21:02:48 +0000 (13:02 -0800)]
ASoC: wm8996: Convert to use DAPM routes for stream connections
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Mon, 10 Oct 2011 17:31:44 +0000 (18:31 +0100)]
ASoC: wm5100: Implement DRC coefficient configuration
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 21 Feb 2012 19:13:10 +0000 (19:13 +0000)]
ASoC: wm8996: Implement DRC coefficient configuration
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sat, 18 Feb 2012 00:20:33 +0000 (16:20 -0800)]
ASoC: core: Add support for masking out parts of coefficient blocks
Chip designers frequently include things like the enable and disable
controls for algorithms in the register blocks which also hold the
coefficients. Since it's desirable to split out the enable/disable
control from userspace the plain SND_SOC_BYTES() isn't optimal for
these devices.
Add a SND_SOC_BYTES_MASK() which allows a bitmask from the first word
of the block to be excluded from the control. This supports the needs
of devices I've looked at and lets us have a reasonably simple API.
Further controls can be added in future if that's needed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Mon, 10 Oct 2011 17:31:26 +0000 (18:31 +0100)]
ASoC: core: Add SND_SOC_BYTES control for coefficient blocks
Allow devices to export blocks of registers to the application layer,
intended for use for reading and writing coefficient data which can't
usefully be worked with by the kernel at runtime (for example, due to
requiring complex and expensive calculations or being the results of
callibration procedures). Currently drivers are using platform data to
provide configurations for coefficient blocks which isn't at all
convenient for runtime management or configuration development.
Currently only devices using regmap are supported, an error will be
generated for any attempt to work with a byte control on a non-regmap
device. There's no fundamental block to other devices so support could
be added if required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Fri, 17 Feb 2012 22:33:29 +0000 (14:33 -0800)]
ASoC: io: Retrieve val_bytes from the regmap API
Allow us to build infrastructure which needs to know the size of a value
without requiring regmap based drivers to supply this information to both
ASoC and regmap by asking regmap for the value.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Tue, 21 Feb 2012 19:34:01 +0000 (19:34 +0000)]
Merge tag 'topic/introspection' of git://git./linux/kernel/git/broonie/regmap into HEAD
New interfaces to allow other subsystems to gather information about the
regmap, allowing them to build further subsystem specific generic
features on top of the regmap.
Merged into ASoC in order to allow us to implement SND_SOC_BYTES_MASK()
controls which need to know the word size of the underlying registers.
Lars-Peter Clausen [Tue, 21 Feb 2012 16:47:57 +0000 (17:47 +0100)]
ASoC: mxs-pcm: Remove unused fields from struct mxs_pcm_runtime_data
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lars-Peter Clausen [Tue, 21 Feb 2012 16:47:56 +0000 (17:47 +0100)]
ASoC: imx-pcm: Remove unused fields from imx_pcm_runtime_data struct
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lars-Peter Clausen [Tue, 21 Feb 2012 16:47:55 +0000 (17:47 +0100)]
ASoC: imx-pcm: Remove empty prepare callback
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 21 Feb 2012 16:23:35 +0000 (16:23 +0000)]
ASoC: wm8994: Support external capacitors on MICBIAS2 with jack detection
When an external capacitor is connected to MICBIAS2 on devices with
jack detection (which is not required but may be done in some systems)
then the loading may mean that better performance is obtained when
the microphone bias is enabled normally rather than using the low power
mode. Provide platform data allowing systems to indicate if they require
this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 21 Feb 2012 13:45:53 +0000 (13:45 +0000)]
ASoC: wm8994: Actively discharge idle MICBIAS with jack detect
This minimises the chance of any external capacitors that are fitted
being discharged into headphones as they insert.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 21 Feb 2012 10:50:50 +0000 (10:50 +0000)]
ASoC: wm8994: Enable headphone startup mode 1 for WM1811 and WM8958
The latest recommendation for optimal performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Peter Ujfalusi [Tue, 21 Feb 2012 07:34:20 +0000 (09:34 +0200)]
ASoC: twl4030: Debug code cleanup
Replace the printk(KERN_ERR* instances with dev_err in the driver.
While we are here clean up some of the debug messages as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 21 Feb 2012 09:36:49 +0000 (09:36 +0000)]
ASoC: wm_hubs: Convert headphone driver to output driver widget
Mostly for neatness, though it may help with sequencing in some
situations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 21 Feb 2012 09:12:25 +0000 (09:12 +0000)]
ASoC: wm8776: Add WM8775 device ID to the WM8776
The WM8775 is register compatible with the WM8776 so can be supported with
the same driver though it is an ADC only part. Add the device ID to the
WM8776 driver, further updates will be added in the future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Fri, 17 Feb 2012 06:50:35 +0000 (22:50 -0800)]
ASoC: ak4104: Convert to module_spi_driver()
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Fri, 17 Feb 2012 06:50:18 +0000 (22:50 -0800)]
ASoC: ak4104: Remove uninformative print on probe()
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Fri, 17 Feb 2012 22:20:14 +0000 (14:20 -0800)]
regmap: Allow users to query the size of register values
Generic infrastructure based on top of regmap may want to operate on
blocks of data and therefore find it useful to find the size of the
register values. Provide an accessor operation for this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>