Yuri Tikhonov [Fri, 15 Aug 2008 13:42:09 +0000 (15:42 +0200)]
RX 8025 RTC: analyze 12/24-hour mode flag in rtc_get().
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Stefan Roese [Fri, 5 Sep 2008 08:47:46 +0000 (10:47 +0200)]
devices: Use list_add_tail() instead of list_add() to register a device
This patch fixes a problem spotted on Glacier/Canyonlands (and most
likely lots of other board ports), that no serial output was seen
after console initialization in console_init_r(). This is because the
last added console device was used instead of the first added.
This patch fixes this problem by using list_add_tail() instead of
list_add() to register a device. This way the first added console
is used again.
Signed-off-by: Stefan Roese <sr@denx.de>
Wolfgang Denk [Wed, 3 Sep 2008 21:44:42 +0000 (23:44 +0200)]
Merge branch 'master' of ssh://10.10.0.7/home/wd/git/u-boot/master
Wolfgang Denk [Wed, 3 Sep 2008 21:44:18 +0000 (23:44 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx
Nick Spence [Tue, 2 Sep 2008 20:21:16 +0000 (15:21 -0500)]
mpc83xx: fix mpc8313 in-tree building with NAND
and add mpc8313 NAND build to MAKEALL
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Wolfgang Denk [Wed, 3 Sep 2008 21:07:41 +0000 (23:07 +0200)]
Merge branch 'master' of ssh://10.10.0.7/home/wd/git/u-boot/master
Nick Spence [Thu, 28 Aug 2008 21:09:25 +0000 (14:09 -0700)]
mpc83xx: clean up cache operations and unlock_ram_in_cache() functions
Cleans up some latent issues with the data cache control so that
dcache_enable() and dcache_disable() will work reliably (after
unlock_ram_in_cache() has been called)
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Nick Spence [Thu, 28 Aug 2008 21:09:19 +0000 (14:09 -0700)]
mpc83xx: Store and display Arbiter Event Register values
Record the Arbiter Event Register values and optionally display them.
The Arbiter Event Register can record the type and effective address of
an arbiter error, even through an HRESET. This patch stores the values in
the global data structure.
Display of the Arbiter Event registers immediately after the RSR value
can be enabled with defines. The Arbiter values will only be displayed
if an arbiter event has occured since the last Power On Reset, and either
of the following defines exist:
#define CONFIG_DISPLAY_AER_BRIEF - display only the arbiter address and
and type register values
#define CONFIG_DISPLAY_AER_FULL - display and interpret the arbiter
event register values
Address Only transactions are one of the trapped events that can register
as an arbiter event. They occur with some cache manipulation instructions
if the HID0_ABE (Address Broadcast Enable) is set and the memory region
has the MEMORY_COHERENCE WIMG bit set. Setting:
#define CONFIG_MASK_AER_AO - prevents the arbiter from recording address
only events, so that it can still capture
other real problems.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Nick Spence [Thu, 28 Aug 2008 21:09:11 +0000 (14:09 -0700)]
mpc83xx: use r4 instead of r2 in lock_ram_in_cache and unlock_ram_in_cache
This is needed in unlock_ram_in_cache() because it is called from C and
will corrupt the small data area anchor that is kept in R2.
lock_ram_in_cache() is modified similarly as good coding practice, but
is not called from C.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Nick Spence [Sat, 23 Aug 2008 06:52:50 +0000 (23:52 -0700)]
MPC83XX: Fix GPIO configuration - set gpio level before direction
Set DAT value before DIR values to avoid creating glitches on the
GPIO signals.
Set gpio level register before direction register to inhibit
glitches on high level output pins.
Dir and data gets cleared at powerup, so high level output lines see
a short low pulse between setting the direction and level registers.
Issue was seen on a new board with the nReset line of the NOR flash
connected to a GPIO. Setting the direction register puts the NOR flash
in reset so the next instruction to set the level cannot get executed.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Wolfgang Denk [Wed, 3 Sep 2008 20:59:29 +0000 (22:59 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mips
Wolfgang Denk [Wed, 3 Sep 2008 20:55:55 +0000 (22:55 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
Conflicts:
board/esd/dasa_sim/dasa_sim.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Wed, 3 Sep 2008 20:43:57 +0000 (22:43 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-net
Jean-Christophe PLAGNIOL-VILLARD [Tue, 2 Sep 2008 00:58:32 +0000 (02:58 +0200)]
doc/qemu_mips: add doc howto debug u-boot with gdb
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Matthias Fuchs [Wed, 3 Sep 2008 15:15:45 +0000 (17:15 +0200)]
ppx4xx: Fix broken DASA_SIM board
This patch adds initdram() to DASA_SIM boards that has been
removed accidentally by a previous commit.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Mon, 1 Sep 2008 06:35:37 +0000 (08:35 +0200)]
ppc4xx: Remove reference to common/lists.o from some esd linker scripts
This patch removes some direct references to common/lists.o from some
esd linker scripts. This is necessary because the lists source was moved
and is not in the "common" directory anymore.
Signed-off-by: Stefan Roese <sr@denx.de>
Matthias Fuchs [Tue, 2 Sep 2008 14:33:05 +0000 (16:33 +0200)]
ppc4xx: Remove obsolete or unused functions from some esd boards
This patch removes initdram() and testdram() from most esd 405 platforms.
Some boards also have an empty dummy implementation of
misc_init_f(). This is also removed.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Matthias Fuchs [Tue, 2 Sep 2008 13:07:54 +0000 (15:07 +0200)]
ppc4xx: Update VOM405 board configuration
- remove PCI code
- add command line editing
- minor cleanup
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Matthias Fuchs [Tue, 2 Sep 2008 13:07:53 +0000 (15:07 +0200)]
ppc4xx: Remove obsolete initdram() function from VOM405 board
This patch removed the obsolete initdram() function from
VOM405 platform file.
Some minor cleanup.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Matthias Fuchs [Tue, 2 Sep 2008 13:07:52 +0000 (15:07 +0200)]
ppc4xx: Cleanup VOM405 linker script
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Matthias Fuchs [Tue, 2 Sep 2008 13:07:51 +0000 (15:07 +0200)]
ppc4xx: Add fdt support for VOM405 boards
Signed-off-by: Matthias Fuchs <mf@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Matthias Fuchs [Tue, 2 Sep 2008 09:36:14 +0000 (11:36 +0200)]
ppc4xx: Coding style cleanup
Wrap long lines etc.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Matthias Fuchs [Tue, 2 Sep 2008 09:35:56 +0000 (11:35 +0200)]
ppc4xx: Enable USB on PLU405 boards
This patch enables the PCI-OHCI controller on PLU405 board.
Also the default CPU frequency is updated to 266 MHz and
command line editing is enabled.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Matthias Fuchs [Tue, 2 Sep 2008 09:35:35 +0000 (11:35 +0200)]
ppc4xx: Cleanup PLU405 platform file
This patch
- wraps some long lines
- removes unused/obsolete functions: misc_init_f() and initdram()
Signed-off-by: Matthias Fuchs <mf@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Matthias Fuchs [Tue, 2 Sep 2008 09:35:04 +0000 (11:35 +0200)]
ppc4xx: Cleanup PLU405 linker script
Signed-off-by: Matthias Fuchs <mf@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Matthias Fuchs [Tue, 2 Sep 2008 09:34:36 +0000 (11:34 +0200)]
ppc4xx: Add fdt support for PLU405 boards
Signed-off-by: Matthias Fuchs <mf@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Matthias Fuchs [Tue, 2 Sep 2008 09:34:08 +0000 (11:34 +0200)]
ppc4xx: Increase U-Boot size to 384kB for PLU405 boards
Signed-off-by: Matthias Fuchs <mf@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Jochen Friedrich [Tue, 2 Sep 2008 09:24:59 +0000 (11:24 +0200)]
Don't tftp to unknown flash
If a board has a variable number of flash banks, there are empty entries
in flash_info[] and CFG_DIRECT_FLASH_TFTP is set, tftp boot fails with
"Outside available Flash". This patch skips flash banks with unknown
flash ids.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Nobuhiro Iwamatsu [Thu, 28 Aug 2008 04:40:44 +0000 (13:40 +0900)]
net: smc911x: Add pkt_data_pull and pkt_data_push function
The RSK7203 board has the SMSC9118 wired up 'incorrectly'.
Byte-swapping is necessary, and so poor performance is inevitable.
This problem cannot evade by the swap function of CHIP, this can
evade by software Byte-swapping.
And this has problem by FIFO access only. pkt_data_pull/pkt_data_push
functions necessary to solve this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Mon, 1 Sep 2008 03:37:00 +0000 (20:37 -0700)]
Moved initialization of EEPRO100 Ethernet controller to board_eth_init()
Affected boards:
db64360
db64460
katmai
taihu
taishan
yucca
cpc45
cpu87
eXalion
elppc
debris
kvme080
mpc8315erdb
integratorap
ixdp425
oxc
pm826
pm828
pm854
pm856
ppmc7xx
sc3
sc520_spunk
sorcery
tqm8272
tqm85xx
utx8245
Removed initialization of the driver from net/eth.c
Also, wrapped contents of pci_eth_init() by CONFIG_PCI.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Sun, 31 Aug 2008 17:45:44 +0000 (10:45 -0700)]
Moved initialization of TULIP Ethernet controller to board_eth_init()
Affected boards:
cu824
bab7xx
adciop
dasa_sim
mousse
mpc8540eval
musenki
mvblue
pcippc2/pcippc6
sbc8240
stxssa
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Sun, 31 Aug 2008 17:44:19 +0000 (10:44 -0700)]
Moved initialization of E1000 Ethernet controller to board_eth_init()
Affected boards:
ap1000
mvbc_p
PM854
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Sun, 31 Aug 2008 17:40:51 +0000 (10:40 -0700)]
Moved initialization of plb2800 Ethernet driver to board_eth_init
Affected boards:
purple
Removed initialization of controller from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Sun, 31 Aug 2008 17:39:12 +0000 (10:39 -0700)]
Moved initialization of MPC5xxx_FEC Ethernet driver to CPU directory
Modified board_eth_init() functions of boards that have this FEC in addition
to other Ethernet controllers.
Affected boards:
bc3450
icecube
mvbc_p
o2dnt
pm520
total5200
tq5200
Removed initialization of controller from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Sun, 31 Aug 2008 17:36:38 +0000 (10:36 -0700)]
Moved initialization of MPC512x_FEC Ethernet driver to CPU directory
Added a cpu_eth_init() function to MPC512x CPU directory and
removed code from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Sun, 31 Aug 2008 17:16:59 +0000 (10:16 -0700)]
Moved initialization of IncaIP Ethernet controller to board_eth_init
Affected boards:
IncaIP
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Sun, 31 Aug 2008 17:15:26 +0000 (10:15 -0700)]
Moved initialization of 3COM Ethernet controller (AmigaOne) to board_eth_init()
Affected boards:
AmigaOneG3SE
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Sun, 31 Aug 2008 17:13:34 +0000 (10:13 -0700)]
Moved initialization of GT6426x Ethernet controller to board_eth_init()
Affected boards:
EVB64260
P3G4
ZUMA
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Sun, 31 Aug 2008 17:08:43 +0000 (10:08 -0700)]
Moved initialization of PCNET Ethernet controller to board_eth_init()
Affected boards:
PN62
sc520_cdp
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Sun, 31 Aug 2008 17:07:16 +0000 (10:07 -0700)]
Moved initialization of NATSEMI Ethernet controller to board_eth_init()
Affected boards:
a3000
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Sun, 31 Aug 2008 17:03:22 +0000 (10:03 -0700)]
Moved initialization of NS8382X Ethernet controller to board_eth_init()
Affected boards:
bc3450
cpci5200
mecp5200
pf2000
icecube
o2dnt
pm520
sandpoint8245
total5200
tqm5200
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Sun, 31 Aug 2008 16:59:33 +0000 (09:59 -0700)]
Moved initialization of TSI108 Ethernet controller to board_eth_init()
Affected boards:
mpc7448hpc2
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Mon, 1 Sep 2008 04:41:08 +0000 (21:41 -0700)]
Moved initialization of RTL8139 Ethernet controller to board_eth_init()
Affected boards:
hidden_dragon
MPC8544DS
MPC8610HPCN
R2DPLUS
TB0229
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Sun, 31 Aug 2008 16:49:42 +0000 (09:49 -0700)]
Moved initialization of RTL8169 Ethernet controller to board_eth_init()
Affected boards:
linkstation
r7780mp
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Wed, 13 Aug 2008 05:11:53 +0000 (22:11 -0700)]
Moved initialization of Ethernet controllers on Atmel AT91 to board_eth_init()
Removed at91sam9_eth_initialize() from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Mon, 1 Sep 2008 05:22:04 +0000 (22:22 -0700)]
Introduce netdev.h header file and remove externs
This addresses all drivers whose initializers have already
been moved to board_eth_init()/cpu_eth_init().
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Andy Fleming [Sun, 31 Aug 2008 21:33:30 +0000 (16:33 -0500)]
Add pixis_set_sgmii command
The 8544DS and 8572DS platforms support an optional SGMII riser card to
expose ethernet over an SGMII interface. Once the card is in, it is also
necessary to configure the board such that it uses the card, rather than
the on-board ethernet ports. This can either be done by flipping dip switches
on the motherboard, or by modifying registers in the pixis. Either way
requires a reboot.
This adds a command to allow users to choose which ports are routed through
the SGMII card, and which through the onboard ports. It also allows users
to revert to the current switch settings.
This code does not work on the 8572, as the PIXIS is different.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Andy Fleming [Sun, 31 Aug 2008 21:33:29 +0000 (16:33 -0500)]
Add SGMII support for the 8544 DS
The 8544 DS has an optional SGMII Riser card, which uses different PHY
addresses. Check if we are in SGMII mode, and invoke the SGMII Riser
setup code if so.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Andy Fleming [Sun, 31 Aug 2008 21:33:28 +0000 (16:33 -0500)]
Add support for Freescale SGMII Riser Card
The 8544DS and 8572DS systems have an optional SGMII riser card which
exposes new ethernet ports which are connected to the eTSECs via an
SGMII interface. The SGMII PHYs for this board are offset from the standard
PHY addresses, so this code modifies the passed in tsec_info structure to
use the SGMII PHYs on the card, instead.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Andy Fleming [Sun, 31 Aug 2008 21:33:27 +0000 (16:33 -0500)]
Add SGMII support to the tsec
Adds support for configuring the TBI to talk properly with the SerDes.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Andy Fleming [Sun, 31 Aug 2008 21:33:26 +0000 (16:33 -0500)]
Pass in tsec_info struct through tsec_initialize
The tsec driver contains a hard-coded array of configuration information
for the tsec ethernet controllers. We create a default function that works
for most tsecs, and allow that to be overridden by board code. It creates
an array of tsec_info structures, which are then parsed by the corresponding
driver instance to determine configuration. Also, add regs, miiregs, and
devname fields to the tsec_info structure, so that we don't need the kludgy
"index" parameter.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Andy Fleming [Sun, 31 Aug 2008 21:33:25 +0000 (16:33 -0500)]
tsec: Move tsec.h to include/
This is to prepare the way for board code passing in the tsec_info structure
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Sergei Poselenov [Fri, 6 Jun 2008 13:52:44 +0000 (15:52 +0200)]
PHY: Add support for the M88E1121R Marvell chip.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Wolfgang Denk [Tue, 2 Sep 2008 19:17:36 +0000 (21:17 +0200)]
fw_env.c: fix build problems with MTD_VERSION=old
(as needed to support old 2.4 Linux kernel based releases)
Signed-off-by: Wolfgang Denk <wd@denx.de>
Jean-Christophe PLAGNIOL-VILLARD [Mon, 1 Sep 2008 15:11:26 +0000 (17:11 +0200)]
device: make device_register() clone the device
This is expected by the callers, but this fact was hidden well within
the old list implementation.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Wolfgang Denk [Sun, 31 Aug 2008 22:16:29 +0000 (00:16 +0200)]
Merge branch 'Makefile' of git://git.denx.de/u-boot-arm
Wolfgang Denk [Sun, 31 Aug 2008 22:06:05 +0000 (00:06 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Wolfgang Denk [Sun, 31 Aug 2008 22:04:26 +0000 (00:04 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
Wolfgang Denk [Sun, 31 Aug 2008 22:03:40 +0000 (00:03 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-sh
Wolfgang Denk [Sun, 31 Aug 2008 21:53:22 +0000 (23:53 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxx
Nobuhiro Iwamatsu [Sun, 31 Aug 2008 14:28:15 +0000 (23:28 +0900)]
sh: Remove CC line from board's Makefile
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Sun, 31 Aug 2008 14:25:57 +0000 (23:25 +0900)]
sh: Replaced "@./mkconfig" for @$(MKCONFIG)
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Thu, 28 Aug 2008 05:50:52 +0000 (14:50 +0900)]
sh: Add support sh2 to MAKEALL
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Thu, 28 Aug 2008 05:52:23 +0000 (14:52 +0900)]
sh: Fix compile error rsk7203 board
This boards used old type preprocessor.
This patch fix compile error.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Thu, 28 Aug 2008 05:53:31 +0000 (14:53 +0900)]
sh: Fix compile error sh7785lcr board
This boards used old type preprocessor.
This patch fix compile error.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Fri, 22 Aug 2008 08:39:09 +0000 (17:39 +0900)]
sh: Renesas Solutions AP325RXA board support
AP325RXA is SH7723's reference board.
This has SCIF, NOR Flash, Ethernet, USB host, LCDC, SD Host, Camera and other.
In this patch, support SCIF, NOR Flash, and Ethernet.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Fri, 22 Aug 2008 08:48:51 +0000 (17:48 +0900)]
sh: add support Renesas SH7723
Renesas SH7723 has 5 SCIF, SD, Camera, LCDC and other.
This patch supports CPU register's header file and SCIF serial driver.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Sun, 31 Aug 2008 14:02:04 +0000 (23:02 +0900)]
sh: Renesas RSK+ 7203 board support
This adds initial support for the RTE RSK+ SH7203 board.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Thu, 3 Jul 2008 14:11:02 +0000 (23:11 +0900)]
sh: Add support Renesas SH7203 processor
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Sun, 31 Aug 2008 13:48:33 +0000 (22:48 +0900)]
sh: Add support SH2/SH2A which is CPU of Renesas Technology
Add support SH2/SH2A basic function.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Sun, 31 Aug 2008 13:45:08 +0000 (22:45 +0900)]
sh: Renesas R0P7785LC0011RL board support
This board has SH7785, 512MB DDR2-SDRAM, NOR Flash,
Graphic, Ethernet, USB, SD, RTC, and I2C controller.
This patch supports the following functions:
- 128MB DDR2-SDRAM (29-bit address mode only)
- NOR Flash
- USB host
- Ethernet
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Yoshihiro Shimoda [Thu, 10 Jul 2008 10:32:53 +0000 (19:32 +0900)]
sh: add support for SH7785
Renesas SH7785 has DDR2-SDRAM controller, PCI, and other.
This patch supports CPU register's header file.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 31 Aug 2008 02:45:42 +0000 (04:45 +0200)]
davinci: fix remaining dm644x_eth
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 31 Aug 2008 02:24:56 +0000 (04:24 +0200)]
fs: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 31 Aug 2008 02:24:55 +0000 (04:24 +0200)]
devices: merge to list_head
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 31 Aug 2008 02:24:51 +0000 (04:24 +0200)]
update linux/list
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 30 Aug 2008 22:39:48 +0000 (00:39 +0200)]
smdk6400: add gitignore
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 30 Aug 2008 22:39:48 +0000 (00:39 +0200)]
smdk6400: Use CONFIG_FLASH_CFI_DRIVER
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Guennadi Liakhovetski [Sat, 30 Aug 2008 22:39:47 +0000 (00:39 +0200)]
smdk6400: remove redundant bootargs definition
Double bootargs setting leads to a duplicated environmant entry.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Guennadi Liakhovetski [Sat, 30 Aug 2008 22:39:47 +0000 (00:39 +0200)]
ARM: Add support for S3C6400 based SMDK6400 board
SMDK6400 can only boot U-Boot from NAND-flash. This patch adds a nand_spl
driver for it too. The board can also boot from the NOR flash, but due to
hardware limitations it can only address 64KiB on it, which is not enough
for U-Boot. Based on the original sources by Samsung for U-Boot 1.1.6.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Guennadi Liakhovetski [Sat, 30 Aug 2008 22:39:47 +0000 (00:39 +0200)]
NAND: add NAND driver for S3C64XX
Based on the original S3C64XX NAND driver by Samsung for U-Boot 1.1.6.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Guennadi Liakhovetski [Sat, 30 Aug 2008 22:39:47 +0000 (00:39 +0200)]
S3C64XX: remove broken HWFLOW support from the serial driver
As noted by Harald Welte, HWFLOW support in the S3C64XX serial driver is
broken and currently unused. Remove it.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Guennadi Liakhovetski [Sat, 30 Aug 2008 22:39:47 +0000 (00:39 +0200)]
serial: add S3C64XX serial driver
Based on the original S3C64XX UART driver by Samsung for U-Boot 1.1.6.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Guennadi Liakhovetski [Sat, 30 Aug 2008 22:39:46 +0000 (00:39 +0200)]
USB: Add support for OHCI controller on S3C6400
Notice: USB on S3C6400 currently works _only_ with switched off MMU. One could
try to enable the MMU, but map addresses 1-to-1, and disable data cache, then
it should work too and we could still profit from instruction cache.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Guennadi Liakhovetski [Sat, 30 Aug 2008 22:39:46 +0000 (00:39 +0200)]
ARM: Add arm1176 core with S3C6400 SoC
Based on the original S3C64XX port by Samsung for U-Boot 1.1.6.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Sandeep Paulraj [Sat, 30 Aug 2008 22:39:46 +0000 (00:39 +0200)]
ARM DaVinci: Changing function names for EMAC driver
DM644x is just one of a series of DaVinci chips that use the EMAC driver.
By replacing all the function names that start with dm644x_* to davinci_*
we make these function more portable. I have tested this change on my EVM.
DM6467 is another DaVinci SOC which uses the EMAC driver and i will
be sending patches that add DaVinci DM6467 support to the list soon.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Gururaja Hebbar K R [Sat, 30 Aug 2008 21:21:30 +0000 (23:21 +0200)]
Integrator[AP/CP] - Remove unused file memsetup.S
- memsetup.s is changed/merged to lowlevel_init.S
memsetup.S has a global label memsetup that just returns back to caller
- memsetup global label is changed/merged to lowlevel_init
This label is not called from anywhere.
Signed-off-by: Gururaja Hebbar <gururajakr@sanyo.co.in>
Hugo Villeneuve [Wed, 27 Aug 2008 19:35:52 +0000 (21:35 +0200)]
ARM DaVinci: Standardize names of directories/files
ARM DaVinci: Standardize names of directories/files.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Hugo Villeneuve [Fri, 11 Jul 2008 19:10:13 +0000 (15:10 -0400)]
ARM DaVinci: Move common functions to board/davinci/common
ARM DaVinci: Move common functions to board/davinci/common.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Stefan Roese [Fri, 29 Aug 2008 09:56:49 +0000 (11:56 +0200)]
ppc4xx/NAND: Add select_chip function to 4xx NDFC driver
This function is needed for the new NAND infrastructure. We only need
a dummy implementation though for the NDFC.
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Fri, 29 Aug 2008 10:06:27 +0000 (12:06 +0200)]
ppc4xx: Increase image size for NAND boot target
This is needed since now with HUSH enabled (amcc-common.h) the image
read from NAND exceeds the previous limit.
Signed-off-by: Stefan Roese <sr@denx.de>
Ben Warren [Fri, 29 Aug 2008 06:58:30 +0000 (23:58 -0700)]
Move MPC512x_FEC driver to drivers/net
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Fri, 29 Aug 2008 06:58:29 +0000 (23:58 -0700)]
Move MPC5xxx_FEC driver to drivers/net
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 29 Aug 2008 19:53:57 +0000 (21:53 +0200)]
cmd_terminal: remove no need ifdef
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 29 Aug 2008 19:53:57 +0000 (21:53 +0200)]
common/Makefile: order by functionality
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 29 Aug 2008 19:53:56 +0000 (21:53 +0200)]
miiphyutil: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 29 Aug 2008 19:53:37 +0000 (21:53 +0200)]
autoscript: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 28 Aug 2008 23:18:11 +0000 (01:18 +0200)]
crc16: move to lib_generic
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 28 Aug 2008 23:18:01 +0000 (01:18 +0200)]
miiphybb: move to drivers/net/phy
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 28 Aug 2008 10:31:51 +0000 (12:31 +0200)]
soft_spi: move to drivers/spi
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>