Zoran Turalija [Sun, 2 Jun 2013 17:56:33 +0000 (14:56 -0300)]
[media] stb0899: allow minimum symbol rate of 2000000
Looks like product datasheets for tuners containing STB0899 are
suggesting specification for min. symbol rate of 2MS/s.
Some specs found here, all suggesting 2MS/s for min. symbol rate:
Comtech DVBS2-6899
http://comtech.sg1002.myweb.hinet.net/pdf/dvbs2-6899.pdf
TechniSat SkyStar HD2
http://www.scaistar.com/skystar2/skystarhd2.htm
Azurewave AD-SP400
http://www.pulsat.com/products/AzureWave-AD%252dSP400-High-Definition-PC-Card.html
New patch:
This makes minimum symbol rate driver capabilities on par with some
accessible datasheet specifications*, and allows tuning on linux to
transponders that have symbol rate between 2000000-5000000, too.
Patch was tested successfully on Eutelsat 16A transponders that
became reachable with it (2000000 < symbol rate < 5000000):
* DVB/S
12507050 V 2532000 3/4
* DVB/S2
12574000 V 4355000 3/4 8PSK
* DVB/S
12593000 V 2500000 2/3
* DVB/S
12596940 V 2848000 2/3
* DVB/S
12600750 V 2500000 1/2
* DVB/S
12675590 H 4248000 3/4
(*) Datasheet: http://comtech.sg1002.myweb.hinet.net/pdf/dvbs2-6899.pdf
Maximum Symbol Rate
QPSK/LDPC/PCH: 20-30Mbps
8PSK/LDPC/BCH: 10-30Mbps
DVB: 2-45Mbps
^--------- min. symbol rate
Signed-off-by: Zoran Turalija <zoran.turalija@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reinhard Nißl [Sun, 2 Jun 2013 17:52:43 +0000 (14:52 -0300)]
[media] stb0899: fix inversion enum values to match usage with CFR
Throughout the zig-zag-implementations, inversion is taken into
account when reading and writing the CFR register, which contains
the derotator frequency. As swapping IQ signals changes the sign
of that register for example, the idea is to compensate that sign
change by multiplying the register value with the inversion enum
value.
The current enum values 0 and 1 for IQ_SWAP_OFF and IQ_SWAP_ON
don't work in the case IQ_SWAP_OFF, due to the multiplication by
zero (I've only found a single device which actually uses
IQ_SWAP_OFF in it's config).
I've changed the enum values to +1 and -1 to accommodate to the
intended usage.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reinhard Nißl [Sun, 2 Jun 2013 17:52:02 +0000 (14:52 -0300)]
[media] stb0899: enable auto inversion handling unconditionally
It seems that current inversion handling addresses only the signal
routing on the PCB, i. e. IQ signals are either swapped or not.
But when the device is operated in a Satellite Channel Router (SCR)
environment, an additional inversion is required due to the way how
the SCR works. Therefore it makes sense to me to always enable auto
inversion handling and drop the enum value IQ_SWAP_AUTO.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Zoran Turalija [Sun, 2 Jun 2013 17:40:51 +0000 (14:40 -0300)]
[media] stb0899: allow minimum symbol rate of 1000000
This makes minimum symbol rate driver capabilities on par with
windows driver, and allows tuning on linux to transponders that
have symbol rate below 5000000, too.
Patch was tested successfully on Eutelsat 16A transponders that
became reachable with it (1000000 < symbol rate < 5000000):
* DVB/S
12507050 V 2532000 3/4
* DVB/S2
12574000 V 4355000 3/4 8PSK
* DVB/S
12593000 V 2500000 2/3
* DVB/S
12596940 V 2848000 2/3
* DVB/S
12600750 V 2500000 1/2
* DVB/S
12675590 H 4248000 3/4
Signed-off-by: Zoran Turalija <zoran.turalija@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reinhard Nißl [Sun, 2 Jun 2013 17:37:06 +0000 (14:37 -0300)]
[media] stb0899: sign extend raw CRL_FREQ value
Contrary to the chip's specs, the register's value is signed, so we
need to sign extend the value before using it in calculations like
when determining the offset frequency.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thomas Meyer [Sat, 1 Jun 2013 08:53:10 +0000 (05:53 -0300)]
[media] dma-buf: Cocci spatch "ptr_ret.spatch"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Gianluca Gennari [Sun, 2 Jun 2013 17:26:15 +0000 (14:26 -0300)]
[media] r820t: do not double-free fe->tuner_priv in r820t_release()
fe->tuner_priv is already freed by hybrid_tuner_release_state().
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Geert Uytterhoeven [Sun, 2 Jun 2013 16:52:17 +0000 (13:52 -0300)]
[media] dib8000: Fix dib8000_set_frontend() never setting ret
drivers/media/dvb-frontends/dib8000.c: In function ‘dib8000_set_frontend’:
drivers/media/dvb-frontends/dib8000.c:3556: warning: ‘ret’ is used uninitialized in this function
Remove the variable and return zero instead.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart [Fri, 26 Apr 2013 01:28:51 +0000 (22:28 -0300)]
[media] uvcvideo: Fix open/close race condition
Maintaining the users count using an atomic variable makes sure that
access to the counter won't be racy, but doesn't serialize access to the
operations protected by the counter. This creates a race condition that
could result in the status URB being submitted multiple times.
Use a mutex to protect the users count and serialize access to the
status start and stop operations.
Reported-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Joseph Salisbury [Wed, 15 May 2013 20:38:48 +0000 (17:38 -0300)]
[media] uvcvideo: quirk PROBE_DEF for Alienware X51 OmniVision webcam
BugLink: http://bugs.launchpad.net/bugs/1180409
OminiVision webcam 0x05a9:0x2643 needs the same UVC_QUIRK_PROBE_DEF
as other OmniVision models to work properly.
Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Kamal Mostafa [Mon, 15 Apr 2013 19:01:51 +0000 (16:01 -0300)]
[media] uvcvideo: quirk PROBE_DEF for Dell Studio / OmniVision webcam
BugLink: https://bugs.launchpad.net/bugs/1168430
OminiVision webcam 0x05a9:0x264a (in Dell Studio Hybrid 140g) needs the
same UVC_QUIRK_PROBE_DEF as other OmniVision model to be recognized
consistently.
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Philipp Zabel [Thu, 23 May 2013 13:43:01 +0000 (10:43 -0300)]
[media] coda: do not call v4l2_m2m_job_finish from .job_abort
If we just declare the job finished here while the CODA is still
running, the call to v4l2_m2m_ctx_release in coda_release, which
is supposed to wait for a running job to finish, will return
immediately and free memory that the CODA is still using.
Just set the 'aborting' flag and let coda_irq_handler deal with it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Philipp Zabel [Thu, 23 May 2013 13:43:00 +0000 (10:43 -0300)]
[media] coda: replace completion with mutex
Not only do we need to wait for job completion when we want to
call a command on the CODA in start/stop_streaming, we also need
to make sure that a new job doesn't start before the command
finished.
Use a mutex to lock the coda command handling. On timeout, the
device_run job must be marked as finished and the mutex released,
as otherwise coda_release will block.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Philipp Zabel [Thu, 23 May 2013 13:42:59 +0000 (10:42 -0300)]
[media] coda: add coda_encode_header helper function
In preparation for CODA7541 and CODA960 multi-stream support and for
replacement of the completion with a mutex lock, consolidate the
header encoding in a helper function.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Philipp Zabel [Thu, 23 May 2013 13:42:58 +0000 (10:42 -0300)]
[media] coda: per-product list of codecs instead of list of formats
This patch adds a list of supported codecs per device type which is used to
determine the allowed pixel formats and maximum frame sizes depending on the
possible codecs. It allows frame sizes larger than 720 x 576 on CODA7 and adds
support for the YVU420 (planar YUV 4:2:0 with switched Cb and Cr) format.
Other uncompressed formats that could be added in the future are the chroma
interleaved NV12 and NV21 formats and the multiplanar variants YUV420M,
YVU420M, NV12M, and NV21M.
Further, rawstreamon is renamed to streamon_out and compstreamon is renamed
to streamon_cap in preparation for decoding support. The maximum encoded
frame buffer size is increased to 1 MiB.
Instead of tracking inst_type and codec across S_FMT calls, set the codec
and inst_type in start_streaming.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Philipp Zabel [Thu, 23 May 2013 13:42:57 +0000 (10:42 -0300)]
[media] coda: simplify parameter buffer setup code
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Philipp Zabel [Thu, 23 May 2013 13:42:56 +0000 (10:42 -0300)]
[media] coda: clear registers in coda_hw_init
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Philipp Zabel [Thu, 23 May 2013 13:42:55 +0000 (10:42 -0300)]
[media] coda: stop setting bytesused in buf_prepare
The application must have filled the bytesused field,
don't overwrite it here.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Philipp Zabel [Thu, 23 May 2013 13:42:54 +0000 (10:42 -0300)]
[media] coda: frame stride must be a multiple of 8
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Philipp Zabel [Thu, 23 May 2013 13:42:53 +0000 (10:42 -0300)]
[media] coda: fix ENC_SEQ_OPTION for CODA7
GAMMA_OFFSET is different between CodaDx6 and CODA7.
Also, this is a bitfield.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lad, Prabhakar [Tue, 14 May 2013 04:45:17 +0000 (01:45 -0300)]
[media] media: pci: remove duplicate checks for EPERM
This patch removes check for EPERM in dbg_g/s_register and
vidioc_g/s_register as this check is already performed by core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lad, Prabhakar [Tue, 14 May 2013 04:45:16 +0000 (01:45 -0300)]
[media] media: usb: remove duplicate checks for EPERM in vidioc_g/s_register
This patch removes check for EPERM in vidioc_g/s_register
as this check is already performed by core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lad, Prabhakar [Tue, 14 May 2013 04:45:15 +0000 (01:45 -0300)]
[media] media: dvb-frontends: remove duplicate checks for EPERM in dbg_g/s_register
This patch removes check for EPERM in dbg_g/s_register
as this check is already performed by core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lad, Prabhakar [Tue, 14 May 2013 04:45:14 +0000 (01:45 -0300)]
[media] media: i2c: remove duplicate checks for EPERM in dbg_g/s_register
This patch removes check for EPERM in dbg_g/s_register of subdevice
drivers as this check is already performed by core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Philipp Zabel [Tue, 21 May 2013 13:32:42 +0000 (10:32 -0300)]
[media] coda: do not use v4l2_dev in coda_timeout
The timeout delayed work might be scheduled even after the v4l2 device is
released.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Philipp Zabel [Tue, 21 May 2013 13:31:25 +0000 (10:31 -0300)]
[media] coda: fix error return value if v4l2_m2m_ctx_init fails
Use ret from the outer scope, instead of redefining it in the
conditional clause. That way the error value reaches the end of
the function as intended.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Philipp Zabel [Tue, 21 May 2013 07:24:16 +0000 (04:24 -0300)]
[media] coda: set umask 0644 on debug module param
Otherwise module/coda/parameters/coda_debug won't show up in sysfs.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Philipp Zabel [Thu, 23 May 2013 10:06:30 +0000 (07:06 -0300)]
[media] coda: enable dmabuf support
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Philipp Zabel [Tue, 21 May 2013 07:19:27 +0000 (04:19 -0300)]
[media] coda: use devm_ioremap_resource
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Philipp Zabel [Tue, 21 May 2013 07:18:22 +0000 (04:18 -0300)]
[media] coda: v4l2-compliance fix: add bus_info prefix 'platform'
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sachin Kamat [Mon, 13 May 2013 08:24:08 +0000 (05:24 -0300)]
[media] rc: gpio-ir-recv: Remove redundant platform_set_drvdata()
Commit
0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sachin Kamat [Mon, 13 May 2013 08:24:07 +0000 (05:24 -0300)]
[media] timblogiw: Remove redundant platform_set_drvdata()
Commit
0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 10 May 2013 11:06:50 +0000 (08:06 -0300)]
[media] bw-qcam: fix timestamp handling
bw-qcam didn't set the timestamp and it didn't set q->timestamp_type.
Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lad, Prabhakar [Tue, 14 May 2013 09:45:31 +0000 (06:45 -0300)]
[media] media: i2c: tvp7002: rearrange description of structure members
This patch rearranges the description of field members of
struct tvp7002_config. Also as the all the fields where accepting
a value either 0/1, made the members as bool.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lad, Prabhakar [Tue, 14 May 2013 09:45:30 +0000 (06:45 -0300)]
[media] media: i2c: tvp7002: remove duplicate define
this patch removes duplicate #define TVP7002_MODULE_NAME
form the driver file, which was also defined in media/tvp7002.h
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Leonid Kegulskiy [Mon, 13 May 2013 10:10:42 +0000 (07:10 -0300)]
[media] hdpvr: Removed unnecessary use of kzalloc() in get_video_info()
[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: Leonid Kegulskiy <leo@lumanate.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lad, Prabhakar [Mon, 20 May 2013 09:02:40 +0000 (06:02 -0300)]
[media] videodev2.h: fix typos
This patch fixes several typos in videodev2.h file
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare [Wed, 15 May 2013 20:56:11 +0000 (17:56 -0300)]
[media] sony-btf-mpx: Drop needless newline in param description
Module parameter descriptions need not be terminated with a newline.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Wei Yongjun [Mon, 13 May 2013 13:00:01 +0000 (10:00 -0300)]
[media] sta2x11_vip: fix error return code in sta2x11_vip_init_one()
The orig code will release all the resources if v4l2_device_register()
failed and return 0. But what we need in this case is to return an
negative error code to let the caller known we are failed.
So the patch save the return value of v4l2_device_register() to 'ret'
and return it when error.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Wei Yongjun [Mon, 13 May 2013 07:52:16 +0000 (04:52 -0300)]
[media] blackfin: fix error return code in bcap_probe()
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Wei Yongjun [Mon, 13 May 2013 05:00:10 +0000 (02:00 -0300)]
[media] ad9389b: fix error return code in ad9389b_probe()
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Wei Yongjun [Mon, 13 May 2013 04:57:37 +0000 (01:57 -0300)]
[media] vpif_capture: fix error return code in vpif_probe()
Fix to return -ENODEV in the subdevice register error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Wei Yongjun [Mon, 13 May 2013 04:57:23 +0000 (01:57 -0300)]
[media] vpif_display: fix error return code in vpif_probe()
Fix to return -ENODEV in the subdevice register error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Wei Yongjun [Mon, 13 May 2013 04:48:45 +0000 (01:48 -0300)]
[media] v4l: vb2: fix error return code in __vb2_init_fileio()
Fix to return -EINVAL in the get kernel address error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Randy Dunlap [Mon, 20 May 2013 15:32:39 +0000 (12:32 -0300)]
[media] media: fix hdpvr kconfig/build errors
Fix hdpvr build errors when CONFIG_I2C=m and VIDEO_V4L2=m and
VIDEO_HDPVR=y.
drivers/built-in.o: In function `hdpvr_disconnect':
hdpvr-core.c:(.text+0xef542): undefined reference to `v4l2_device_disconnect'
hdpvr-core.c:(.text+0xef57e): undefined reference to `i2c_del_adapter'
hdpvr-core.c:(.text+0xef58a): undefined reference to `video_unregister_device'
drivers/built-in.o: In function `hdpvr_delete':
(.text+0xef5b9): undefined reference to `video_device_release'
drivers/built-in.o: In function `hdpvr_probe':
hdpvr-core.c:(.text+0xef63a): undefined reference to `v4l2_device_register'
hdpvr-core.c:(.text+0xefd97): undefined reference to `i2c_del_adapter'
drivers/built-in.o: In function `hdpvr_s_ctrl':
hdpvr-video.c:(.text+0xf03c0): undefined reference to `v4l2_ctrl_activate'
drivers/built-in.o: In function `hdpvr_device_release':
hdpvr-video.c:(.text+0xf0470): undefined reference to `v4l2_device_unregister'
hdpvr-video.c:(.text+0xf0479): undefined reference to `v4l2_ctrl_handler_free'
hdpvr-video.c:(.text+0xf048f): undefined reference to `i2c_del_adapter'
drivers/built-in.o: In function `hdpvr_open':
hdpvr-video.c:(.text+0xf0570): undefined reference to `video_devdata'
hdpvr-video.c:(.text+0xf057b): undefined reference to `v4l2_fh_init'
hdpvr-video.c:(.text+0xf0583): undefined reference to `v4l2_fh_add'
drivers/built-in.o: In function `video_drvdata':
hdpvr-video.c:(.text+0xf08a0): undefined reference to `video_devdata'
drivers/built-in.o: In function `vidioc_s_dv_timings':
hdpvr-video.c:(.text+0xf0d34): undefined reference to `v4l_match_dv_timings'
drivers/built-in.o: In function `hdpvr_poll':
hdpvr-video.c:(.text+0xf1455): undefined reference to `v4l2_ctrl_poll'
drivers/built-in.o: In function `hdpvr_release':
hdpvr-video.c:(.text+0xf18f6): undefined reference to `v4l2_fh_release'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1be3): undefined reference to `v4l2_ctrl_handler_init_class'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1c19): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1c42): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1c6b): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1cac): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1cd5): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o:(.text+0xf1cfe): more undefined references to `v4l2_ctrl_new_std' follow
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1d75): undefined reference to `v4l2_ctrl_new_std_menu'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1d9e): undefined reference to `v4l2_ctrl_new_std_menu'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1dc3): undefined reference to `v4l2_ctrl_new_std_menu'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1de5): undefined reference to `v4l2_ctrl_new_std_menu'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1e18): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1e4b): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1e90): undefined reference to `v4l2_ctrl_cluster'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1e98): undefined reference to `v4l2_ctrl_handler_setup'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1ec1): undefined reference to `video_device_alloc'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1f85): undefined reference to `__video_register_device'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1fac): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o: In function `hdpvr_register_ir_tx_i2c':
(.text+0xf238f): undefined reference to `i2c_new_device'
drivers/built-in.o: In function `hdpvr_register_ir_rx_i2c':
(.text+0xf2434): undefined reference to `i2c_new_device'
drivers/built-in.o: In function `hdpvr_register_i2c_adapter':
(.text+0xf2514): undefined reference to `i2c_add_adapter'
drivers/built-in.o:(.rodata+0x1b368): undefined reference to `video_ioctl2'
drivers/built-in.o:(.rodata+0x1b690): undefined reference to `v4l2_ctrl_log_status'
drivers/built-in.o:(.rodata+0x1b6f8): undefined reference to `v4l2_ctrl_subscribe_event'
drivers/built-in.o:(.rodata+0x1b700): undefined reference to `v4l2_event_unsubscribe'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jakob Normark [Sun, 19 May 2013 12:30:23 +0000 (09:30 -0300)]
[media] Missing break statement added in smsdvb-main.c
Fix missing break that so that n_layers are not accidentally incorrect
Kernel version: v3.10-rc1
Signed-off-by: Jakob Normark <jakobnormark@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Tue, 21 May 2013 14:36:30 +0000 (11:36 -0300)]
[media] saa7115: Don't use a dynamic array
At least on s390, gcc complains about that:
drivers/media/i2c/saa7115.c: In function 'saa711x_detect_chip.constprop.2':
drivers/media/i2c/saa7115.c:1647:1: warning: 'saa711x_detect_chip.constprop.2' uses dynamic stack allocation [enabled by default]
While for me the above report seems utterly bogus, as the
compiler should be optimizing saa711x_detect_chip, merging
it with saa711x_detect_chip and changing:
char chip_ver[size - 1];
to
char chip_ver[16];
because this function is only called on this code snippet:
char name[17];
...
ident = saa711x_detect_chip(client, id, name, sizeof(name));
It seems that gcc is not optimizing it, at least on s390.
As getting rid of it is easy, let's do it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Wed, 17 Apr 2013 11:22:16 +0000 (08:22 -0300)]
[media] videobuf-dma-contig: use vm_iomap_memory()
vm_iomap_memory() provides a better end user interface than
remap_pfn_range(), as it does the needed tests before doing
mmap.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Roberto Alcântara [Sat, 11 May 2013 14:53:29 +0000 (11:53 -0300)]
[media] smscoreapi: Make Siano firmware load more verbose
If firmware load fails, report it as an error.
Signed-off-by: Roberto Alcantara <roberto@eletronica.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Al Viro [Thu, 9 May 2013 18:03:33 +0000 (15:03 -0300)]
[media] videobuf_vm_{open,close} race fixes
just use videobuf_queue_lock(map->q) to protect map->count; vm_area_operations
->open() and ->close() are called just under vma->vm_mm->mmap_sem, which
doesn't help the drivers at all, since clonal VMAs are normally in different
address spaces...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reinhard Nissl [Wed, 8 May 2013 20:54:57 +0000 (17:54 -0300)]
[media] stb0899: remove commented value from IQ_SWAP_ON/OFF usages
As the enum values have changed recently, the comments are void.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Randy Dunlap [Wed, 8 May 2013 20:28:13 +0000 (17:28 -0300)]
[media] media/usb: fix kconfig dependencies
(a.k.a. Kconfig bool depending on a tristate considered harmful)
Fix various build errors when CONFIG_USB=m and media USB drivers
are builtin. In this case, CONFIG_USB_ZR364XX=y,
CONFIG_VIDEO_PVRUSB2=y, and CONFIG_VIDEO_STK1160=y.
This is caused by (from drivers/media/usb/Kconfig):
menuconfig MEDIA_USB_SUPPORT
bool "Media USB Adapters"
depends on USB && MEDIA_SUPPORT
=m =y
so MEDIA_USB_SUPPORT=y and all following Kconfig 'source' lines
are included. By adding an "if USB" guard around most of this file,
the needed dependencies are enforced.
drivers/built-in.o: In function `zr364xx_start_readpipe':
zr364xx.c:(.text+0xc726a): undefined reference to `usb_alloc_urb'
zr364xx.c:(.text+0xc72bb): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `zr364xx_stop_readpipe':
zr364xx.c:(.text+0xc72fd): undefined reference to `usb_kill_urb'
zr364xx.c:(.text+0xc7309): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `read_pipe_completion':
zr364xx.c:(.text+0xc7acc): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `send_control_msg.constprop.12':
zr364xx.c:(.text+0xc7d2f): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `pvr2_ctl_timeout':
pvrusb2-hdw.c:(.text+0xcadb6): undefined reference to `usb_unlink_urb'
pvrusb2-hdw.c:(.text+0xcadcb): undefined reference to `usb_unlink_urb'
drivers/built-in.o: In function `pvr2_hdw_create':
(.text+0xcc42c): undefined reference to `usb_alloc_urb'
drivers/built-in.o: In function `pvr2_hdw_create':
(.text+0xcc448): undefined reference to `usb_alloc_urb'
drivers/built-in.o: In function `pvr2_hdw_create':
(.text+0xcc5f9): undefined reference to `usb_set_interface'
drivers/built-in.o: In function `pvr2_hdw_create':
(.text+0xcc65a): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `pvr2_hdw_create':
(.text+0xcc666): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `pvr2_send_request_ex.part.22':
pvrusb2-hdw.c:(.text+0xccbe3): undefined reference to `usb_submit_urb'
pvrusb2-hdw.c:(.text+0xccc83): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `pvr2_hdw_remove_usb_stuff.part.25':
pvrusb2-hdw.c:(.text+0xcd3f9): undefined reference to `usb_kill_urb'
pvrusb2-hdw.c:(.text+0xcd405): undefined reference to `usb_free_urb'
pvrusb2-hdw.c:(.text+0xcd421): undefined reference to `usb_kill_urb'
pvrusb2-hdw.c:(.text+0xcd42d): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `pvr2_hdw_device_reset':
(.text+0xcd658): undefined reference to `usb_lock_device_for_reset'
drivers/built-in.o: In function `pvr2_hdw_device_reset':
(.text+0xcd664): undefined reference to `usb_reset_device'
drivers/built-in.o: In function `pvr2_hdw_cpureset_assert':
(.text+0xcd6f9): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `pvr2_hdw_cpufw_set_enabled':
(.text+0xcd84e): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `pvr2_upload_firmware1':
pvrusb2-hdw.c:(.text+0xcda47): undefined reference to `usb_clear_halt'
pvrusb2-hdw.c:(.text+0xcdb04): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `pvr2_upload_firmware2':
(.text+0xce7dc): undefined reference to `usb_bulk_msg'
drivers/built-in.o: In function `pvr2_stream_buffer_count':
pvrusb2-io.c:(.text+0xd2e05): undefined reference to `usb_alloc_urb'
pvrusb2-io.c:(.text+0xd2e5b): undefined reference to `usb_kill_urb'
pvrusb2-io.c:(.text+0xd2e9f): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `pvr2_stream_internal_flush':
pvrusb2-io.c:(.text+0xd2f9b): undefined reference to `usb_kill_urb'
drivers/built-in.o: In function `pvr2_buffer_queue':
(.text+0xd3328): undefined reference to `usb_kill_urb'
drivers/built-in.o: In function `pvr2_buffer_queue':
(.text+0xd33ea): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `stk1160_read_reg':
(.text+0xd3efa): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `stk1160_write_reg':
(.text+0xd3f4f): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `stop_streaming':
stk1160-v4l.c:(.text+0xd4997): undefined reference to `usb_set_interface'
drivers/built-in.o: In function `start_streaming':
stk1160-v4l.c:(.text+0xd4a9f): undefined reference to `usb_set_interface'
stk1160-v4l.c:(.text+0xd4afa): undefined reference to `usb_submit_urb'
stk1160-v4l.c:(.text+0xd4ba3): undefined reference to `usb_set_interface'
drivers/built-in.o: In function `stk1160_isoc_irq':
stk1160-video.c:(.text+0xd509b): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `stk1160_cancel_isoc':
(.text+0xd50ef): undefined reference to `usb_kill_urb'
drivers/built-in.o: In function `stk1160_free_isoc':
(.text+0xd5155): undefined reference to `usb_free_coherent'
drivers/built-in.o: In function `stk1160_free_isoc':
(.text+0xd515d): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `stk1160_alloc_isoc':
(.text+0xd5278): undefined reference to `usb_alloc_urb'
drivers/built-in.o: In function `stk1160_alloc_isoc':
(.text+0xd52c2): undefined reference to `usb_alloc_coherent'
drivers/built-in.o: In function `stk1160_alloc_isoc':
(.text+0xd53c4): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `zr364xx_driver_init':
zr364xx.c:(.init.text+0x463e): undefined reference to `usb_register_driver'
drivers/built-in.o: In function `pvr_init':
pvrusb2-main.c:(.init.text+0x4662): undefined reference to `usb_register_driver'
drivers/built-in.o: In function `stk1160_usb_driver_init':
stk1160-core.c:(.init.text+0x467d): undefined reference to `usb_register_driver'
drivers/built-in.o: In function `zr364xx_driver_exit':
zr364xx.c:(.exit.text+0x1377): undefined reference to `usb_deregister'
drivers/built-in.o: In function `pvr_exit':
pvrusb2-main.c:(.exit.text+0x1389): undefined reference to `usb_deregister'
drivers/built-in.o: In function `stk1160_usb_driver_exit':
stk1160-core.c:(.exit.text+0x13a0): undefined reference to `usb_deregister'
Suggested-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jon Arne Jørgensen [Fri, 10 May 2013 06:52:28 +0000 (03:52 -0300)]
[media] saa7115: Add register setup and config for gm7113c
The gm7113c chip is similar to the original saa7113 chip, so I try to
re-use most of the saa7113 specific setup-/configuration registers.
According to the datasheet, the gm7113c chip has not implemented
any register-addresses after 0x1f, so I add a new entry to for the chip
to the saa711x_has_reg function.
The devices I've seen using this chip will fail to get stable video-sync
if these registers are not zeroed:
R_14_ANAL_ADC_COMPAT_CNTL
R_15_VGATE_START_FID_CHG
R_16_VGATE_STOP
R_17_MISC_VGATE_CONF_AND_MSB
The saa711x_set_v4lstd is updated to send a simpler configuration-table
to avoid setting these registers.
Signed-off-by: Jon Arne Jørgensen <jonarne@jonarne.no>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Fri, 26 Apr 2013 13:22:48 +0000 (10:22 -0300)]
[media] saa7115: add detection code for gm7113c
Adds a code that (auto)detects gm7113c clones. The auto-detection
here is not perfect, as, on contrary to what it would be expected
by looking into its datasheets some devices would return, instead:
saa7115 0-0025: chip 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 @ 0x4a is unknown
(found on a device labeled as GM7113C 1145 by Ezequiel Garcia)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Jon Arne Jørgensen <jonarne@jonarne.no>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Fri, 26 Apr 2013 13:22:47 +0000 (10:22 -0300)]
[media] saa7115: move the autodetection code out of the probe function
As we're now seeing other variants from chinese clones, like
gm1113c, we'll need to add more bits at the detection code.
So, move it into a separate function.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Jon Arne Jørgensen <jonarne@jonarne.no>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Alexey Khoroshilov [Tue, 7 May 2013 20:57:08 +0000 (17:57 -0300)]
[media] wl128x: do not call copy_to_user() while holding spinlocks
copy_to_user() must not be called with spinlocks held, but it is in
fmc_transfer_rds_from_internal_buff().
The patch copies data to tmpbuf, releases spinlock and then passes it to userspace.
By the way there is a small unification: replace a couple of hardcoded constants by a macro.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ismael Luceno [Fri, 3 May 2013 18:54:57 +0000 (15:54 -0300)]
[media] solo6x10: Approximate frame intervals with non-standard denominator
Instead of falling back to 1/25 (PAL) or 1/30 (NTSC).
Signed-off-by: Ismael Luceno <ismael.luceno@corp.bluecherry.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lad, Prabhakar [Fri, 3 May 2013 07:17:19 +0000 (04:17 -0300)]
[media] media: i2c: tvp7002: enable TVP7002 decoder for media controller based usage
This patch enables tvp7002 decoder driver for media controller
based usage by adding v4l2_subdev_pad_ops operations support
for enum_mbus_code, set_pad_format, get_pad_format and media_entity_init()
on probe and media_entity_cleanup() on remove.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Leonid Kegulskiy [Thu, 25 Apr 2013 08:59:56 +0000 (05:59 -0300)]
[media] hdpvr: Added some error handling in hdpvr_start_streaming()
Signed-off-by: Leonid Kegulskiy <leo@lumanate.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Leonid Kegulskiy [Thu, 25 Apr 2013 08:59:54 +0000 (05:59 -0300)]
[media] hdpvr: Removed unnecessary get_video_info() call from hdpvr_device_init()
Signed-off-by: Leonid Kegulskiy <leo@lumanate.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lad, Prabhakar [Fri, 3 May 2013 11:39:25 +0000 (08:39 -0300)]
[media] media: davinci: vpbe: fix checkpatch warning for CamelCase
This patch fixes checkpatch warning to avoid CamelCase.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jakob Haufe [Sat, 13 Apr 2013 14:03:37 +0000 (11:03 -0300)]
[media] em28xx: Add support for 1b80:e1cc Delock 61959
Hardware is the same as MaxMedia UB425-TC but ships with a different
remote.
Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jakob Haufe [Sat, 13 Apr 2013 14:03:36 +0000 (11:03 -0300)]
[media] rc: Add rc-delock-61959
This adds the keytable for the remote that comes with the Delock 61959.
NEC protocol with address 0x866b.
Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Tue, 21 May 2013 11:16:19 +0000 (08:16 -0300)]
[media] update saa7134 and tuner cardlists
Those are automatically updated using the cardlist script.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sat, 20 Apr 2013 11:57:41 +0000 (08:57 -0300)]
[media] CARDLIST.bttv: add new cards
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lad, Prabhakar [Fri, 19 Apr 2013 08:53:30 +0000 (05:53 -0300)]
[media] media: davinci: vpif_display: move displaying of error to approppraite place
this patch moves the displaying out error case "VPIF IRQ request failed\n"
when there is actual request_irq() fail.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lad, Prabhakar [Fri, 19 Apr 2013 08:53:29 +0000 (05:53 -0300)]
[media] media: davinci: vpif: remove unwanted header file inclusion
this patch removes unwanted header file inclusion and sorts
header alphabetically.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ismael Luceno [Thu, 18 Apr 2013 11:16:08 +0000 (08:16 -0300)]
[media] videodev2.h: Make V4L2_PIX_FMT_MPEG4 comment more specific about its usage
Signed-off-by: Ismael Luceno <ismael.luceno@corp.bluecherry.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ondrej Zary [Sun, 14 Apr 2013 20:26:21 +0000 (17:26 -0300)]
[media] bttv: Add CyberVision CV06
Add CyberVision CV06 4-camera card (from CyberVision SV card kit):
http://www.cybervision.com.tw/products-swcard_kits-sv.html
There are some interesting things on the card but they're not supported:
4 LEDs, a connector with 4 IN and 4 OUT pins, RESET IN and RESET OUT
connectors, a relay and CyberVision CV8088-SV16 chip
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ondrej Zary [Sun, 14 Apr 2013 15:39:09 +0000 (12:39 -0300)]
[media] bttv: Add noname Bt848 capture card with 14MHz xtal
Add support for noname Bt848 capture-only card (3x composite, 1x S-VHS)
with 14MHz crystal:
http://www.rainbow-software.org/images/hardware/bt848_.jpg
14MHz PLL was not supported by bttv driver until now.
[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lars-Peter Clausen [Sat, 13 Apr 2013 08:25:59 +0000 (05:25 -0300)]
[media] media:adv7180: Use dev_pm_ops
Use dev_pm_ops instead of the deprecated legacy suspend/resume callbacks.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Scott Jiang [Fri, 12 Apr 2013 22:52:59 +0000 (19:52 -0300)]
[media] bfin_capture: add query_dv_timings/enum_dv_timings support
More dv_timings ioctl ops are introduced in video core.
Add query_dv_timings/enum_dv_timings accordingly.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Scott Jiang [Fri, 12 Apr 2013 22:52:57 +0000 (19:52 -0300)]
[media] blackfin: add display support in ppi driver
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 12 Apr 2013 12:30:29 +0000 (09:30 -0300)]
[media] bttv: Add Adlink MPG24 entry to the bttv cardlist
Add a proper card entry for this device, rather than abusing entries that are
not-quite-right.
Regards,
Hans
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart [Thu, 2 May 2013 11:29:43 +0000 (08:29 -0300)]
[media] s5k6aa: Convert to devm_gpio_request_one()
Use the devm_gpio_request_one() managed function to simplify cleanup
code paths.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart [Thu, 2 May 2013 11:29:43 +0000 (08:29 -0300)]
[media] s5c73m3: Convert to devm_gpio_request_one()
Use the devm_gpio_request_one() managed function to simplify cleanup
code paths.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart [Thu, 2 May 2013 11:29:43 +0000 (08:29 -0300)]
[media] m5mols: Convert to devm_request_irq()
Using the managed function the free_irq() calls can be removed from the
probe error path and the remove handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart [Thu, 2 May 2013 11:29:43 +0000 (08:29 -0300)]
[media] media: i2c: Convert to devm_regulator_bulk_get()
Using the managed function the regulator_bulk_put() calls can be removed
from the probe error path and the remove handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart [Thu, 2 May 2013 11:29:43 +0000 (08:29 -0300)]
[media] media: i2c: Convert to devm_gpio_request_one()
Using the managed function the gpio_free() calls can be removed from the
probe error path and the remove handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart [Thu, 2 May 2013 11:29:43 +0000 (08:29 -0300)]
[media] media: i2c: Convert to devm_kzalloc()
Using the managed function the kfree() calls can be removed from the
probe error path and the remove handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart [Thu, 2 May 2013 14:11:50 +0000 (11:11 -0300)]
[media] media: i2c: Convert to gpio_request_one()
Replace gpio_request() with gpio_request_one() and remove the associated
gpio_direction_output() calls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart [Thu, 2 May 2013 13:09:07 +0000 (10:09 -0300)]
[media] tvp514x: Fix double free
The tvp514x data structure is allocated using devm_kzalloc(). Freeing it
explictly would result in a double free. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart [Thu, 2 May 2013 11:34:30 +0000 (08:34 -0300)]
[media] mt9v032: Free control handler in cleanup paths
The control handler must be freed in the probe error path and in the
remove handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart [Thu, 2 May 2013 10:57:51 +0000 (07:57 -0300)]
[media] mt9p031: Use gpio_is_valid()
Replace the manual validity checks for the reset GPIO with the
gpio_is_valid() function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Guennadi Liakhovetski [Thu, 18 Apr 2013 21:35:39 +0000 (18:35 -0300)]
[media] mt9p031: Power down the sensor if no supported device has been detected
The mt9p031 driver first accesses the I2C device in its .registered()
method. While doing that it first powers the device up, but if probing
fails, it doesn't power the chip back down. This patch fixes that bug.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Mon, 13 May 2013 18:35:30 +0000 (15:35 -0300)]
Merge tag 'v3.10-rc1' into patchwork
Linux 3.10-rc1
* tag 'v3.10-rc1': (11697 commits)
Linux 3.10-rc1
[SCSI] qla2xxx: Update firmware link in Kconfig file.
[SCSI] iscsi class, qla4xxx: fix sess/conn refcounting when find fns are used
[SCSI] sas: unify the pointlessly separated enums sas_dev_type and sas_device_type
[SCSI] pm80xx: thermal, sas controller config and error handling update
[SCSI] pm80xx: NCQ error handling changes
[SCSI] pm80xx: WWN Modification for PM8081/88/89 controllers
[SCSI] pm80xx: Changed module name and debug messages update
[SCSI] pm80xx: Firmware flash memory free fix, with addition of new memory region for it
[SCSI] pm80xx: SPC new firmware changes for device id 0x8081 alone
[SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files
[SCSI] pm80xx: MSI-X implementation for using 64 interrupts
[SCSI] pm80xx: Updated common functions common for SPC and SPCv/ve
[SCSI] pm80xx: Multiple inbound/outbound queue configuration
[SCSI] pm80xx: Added SPCv/ve specific ids, variables and modify for SPC
[SCSI] lpfc: fix up Kconfig dependencies
[SCSI] Handle MLQUEUE busy response in scsi_send_eh_cmnd
dm cache: set config value
dm cache: move config fns
dm thin: generate event when metadata threshold passed
...
Linus Torvalds [Sun, 12 May 2013 00:14:08 +0000 (17:14 -0700)]
Linux 3.10-rc1
Linus Torvalds [Sun, 12 May 2013 00:04:59 +0000 (17:04 -0700)]
Merge tag 'trace-fixes-v3.10' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing/kprobes update from Steven Rostedt:
"The majority of these changes are from Masami Hiramatsu bringing
kprobes up to par with the latest changes to ftrace (multi buffering
and the new function probes).
He also discovered and fixed some bugs in doing so. When pulling in
his patches, I also found a few minor bugs as well and fixed them.
This also includes a compile fix for some archs that select the ring
buffer but not tracing.
I based this off of the last patch you took from me that fixed the
merge conflict error, as that was the commit that had all the changes
I needed for this set of changes."
* tag 'trace-fixes-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/kprobes: Support soft-mode disabling
tracing/kprobes: Support ftrace_event_file base multibuffer
tracing/kprobes: Pass trace_probe directly from dispatcher
tracing/kprobes: Increment probe hit-count even if it is used by perf
tracing/kprobes: Use bool for retprobe checker
ftrace: Fix function probe when more than one probe is added
ftrace: Fix the output of enabled_functions debug file
ftrace: Fix locking in register_ftrace_function_probe()
tracing: Add helper function trace_create_new_event() to remove duplicate code
tracing: Modify soft-mode only if there's no other referrer
tracing: Indicate enabled soft-mode in enable file
tracing/kprobes: Fix to increment return event probe hit-count
ftrace: Cleanup regex_lock and ftrace_lock around hash updating
ftrace, kprobes: Fix a deadlock on ftrace_regex_lock
ftrace: Have ftrace_regex_write() return either read or error
tracing: Return error if register_ftrace_function_probe() fails for event_enable_func()
tracing: Don't succeed if event_enable_func did not register anything
ring-buffer: Select IRQ_WORK
Linus Torvalds [Sat, 11 May 2013 23:19:30 +0000 (16:19 -0700)]
Merge tag 'stable/for-linus-3.10-rc0-tag-two' of git://git./linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
- More fixes in the vCPU PVHVM hotplug path.
- Add more documentation.
- Fix various ARM related issues in the Xen generic drivers.
- Updates in the xen-pciback driver per Bjorn's updates.
- Mask the x2APIC feature for PV guests.
* tag 'stable/for-linus-3.10-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pci: Used cached MSI-X capability offset
xen/pci: Use PCI_MSIX_TABLE_BIR, not PCI_MSIX_FLAGS_BIRMASK
xen: clear IRQ_NOAUTOEN and IRQ_NOREQUEST
xen: mask x2APIC feature in PV
xen: SWIOTLB is only used on x86
xen/spinlock: Fix check from greater than to be also be greater or equal to.
xen/smp/pvhvm: Don't point per_cpu(xen_vpcu, 33 and larger) to shared_info
xen/vcpu: Document the xen_vcpu_info and xen_vcpu
xen/vcpu/pvhvm: Fix vcpu hotplugging hanging.
Linus Torvalds [Sat, 11 May 2013 22:24:22 +0000 (15:24 -0700)]
Merge tag 'scsi-for-linus' of git://git./linux/kernel/git/jejb/scsi
Pull second SCSI update from James "Jaj B" Bottomley:
"This is the final round of SCSI patches for the merge window. It
consists mostly of driver updates (bnx2fc, ibmfc, fnic, lpfc,
be2iscsi, pm80xx, qla4x and ipr).
There's also the power management updates that complete the patches in
Jens' tree, an iscsi refcounting problem fix from the last pull, some
dif handling in scsi_debug fixes, a few nice code cleanups and an
error handling busy bug fix."
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (92 commits)
[SCSI] qla2xxx: Update firmware link in Kconfig file.
[SCSI] iscsi class, qla4xxx: fix sess/conn refcounting when find fns are used
[SCSI] sas: unify the pointlessly separated enums sas_dev_type and sas_device_type
[SCSI] pm80xx: thermal, sas controller config and error handling update
[SCSI] pm80xx: NCQ error handling changes
[SCSI] pm80xx: WWN Modification for PM8081/88/89 controllers
[SCSI] pm80xx: Changed module name and debug messages update
[SCSI] pm80xx: Firmware flash memory free fix, with addition of new memory region for it
[SCSI] pm80xx: SPC new firmware changes for device id 0x8081 alone
[SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files
[SCSI] pm80xx: MSI-X implementation for using 64 interrupts
[SCSI] pm80xx: Updated common functions common for SPC and SPCv/ve
[SCSI] pm80xx: Multiple inbound/outbound queue configuration
[SCSI] pm80xx: Added SPCv/ve specific ids, variables and modify for SPC
[SCSI] lpfc: fix up Kconfig dependencies
[SCSI] Handle MLQUEUE busy response in scsi_send_eh_cmnd
[SCSI] sd: change to auto suspend mode
[SCSI] sd: use REQ_PM in sd's runtime suspend operation
[SCSI] qla4xxx: Fix iocb_cnt calculation in qla4xxx_send_mbox_iocb()
[SCSI] ufs: Correct the expected data transfersize
...
Linus Torvalds [Sat, 11 May 2013 22:23:17 +0000 (15:23 -0700)]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux
Pull idle update from Len Brown:
"Add support for new Haswell-ULT CPU idle power states"
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
intel_idle: initial C8, C9, C10 support
tools/power turbostat: display C8, C9, C10 residency
Linus Torvalds [Sat, 11 May 2013 21:29:11 +0000 (14:29 -0700)]
Merge git://git.infradead.org/users/eparis/audit
Pull audit changes from Eric Paris:
"Al used to send pull requests every couple of years but he told me to
just start pushing them to you directly.
Our touching outside of core audit code is pretty straight forward. A
couple of interface changes which hit net/. A simple argument bug
calling audit functions in namei.c and the removal of some assembly
branch prediction code on ppc"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: fix message spacing printing auid
Revert "audit: move kaudit thread start from auditd registration to kaudit init"
audit: vfs: fix audit_inode call in O_CREAT case of do_last
audit: Make testing for a valid loginuid explicit.
audit: fix event coverage of AUDIT_ANOM_LINK
audit: use spin_lock in audit_receive_msg to process tty logging
audit: do not needlessly take a lock in tty_audit_exit
audit: do not needlessly take a spinlock in copy_signal
audit: add an option to control logging of passwords with pam_tty_audit
audit: use spin_lock_irqsave/restore in audit tty code
helper for some session id stuff
audit: use a consistent audit helper to log lsm information
audit: push loginuid and sessionid processing down
audit: stop pushing loginid, uid, sessionid as arguments
audit: remove the old depricated kernel interface
audit: make validity checking generic
audit: allow checking the type of audit message in the user filter
audit: fix build break when AUDIT_DEBUG == 2
audit: remove duplicate export of audit_enabled
Audit: do not print error when LSMs disabled
...
Linus Torvalds [Fri, 10 May 2013 16:28:55 +0000 (09:28 -0700)]
Merge branch 'for-3.10' of git://linux-nfs.org/~bfields/linux
Pull nfsd fixes from Bruce Fields:
"Small fixes for two bugs and two warnings"
* 'for-3.10' of git://linux-nfs.org/~bfields/linux:
nfsd: fix oops when legacy_recdir_name_error is passed a -ENOENT error
SUNRPC: fix decoding of optional gss-proxy xdr fields
SUNRPC: Refactor gssx_dec_option_array() to kill uninitialized warning
nfsd4: don't allow owner override on 4.1 CLAIM_FH opens
Linus Torvalds [Fri, 10 May 2013 16:27:40 +0000 (09:27 -0700)]
Merge branch 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86
Pull x86 platform drivers from Matthew Garrett:
"Small set of updates, mainly trivial bugfixes and some small updates
to deal with newer hardware.
There's also a new driver that allows qemu guests to notify the
hypervisor that they've just paniced, which seems useful."
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
Add support for fan button on Ideapad Z580
pvpanic: pvpanic device driver
asus-nb-wmi: set wapf=4 for ASUSTeK COMPUTER INC. X75A
drivers: platform: x86: Use PTR_RET function
sony-laptop: SVS151290S kbd backlight and gfx switch support
hp-wmi: add more definitions for new event_id's
dell-laptop: Fix krealloc() misuse in parse_da_table()
hp_accel: Ignore the error from lis3lv02d_poweron() at resume
dell: add new dell WMI format for the AIO machines
Linus Torvalds [Fri, 10 May 2013 16:21:05 +0000 (09:21 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/signal
Pull stray syscall bits from Al Viro:
"Several syscall-related commits that were missing from the original"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
switch compat_sys_sysctl to COMPAT_SYSCALL_DEFINE
unicore32: just use mmap_pgoff()...
unify compat fanotify_mark(2), switch to COMPAT_SYSCALL_DEFINE
x86, vm86: fix VM86 syscalls: use SYSCALL_DEFINEx(...)
Linus Torvalds [Fri, 10 May 2013 16:20:01 +0000 (09:20 -0700)]
Merge tag 'ecryptfs-3.10-rc1-ablkcipher' of git://git./linux/kernel/git/tyhicks/ecryptfs
Pull eCryptfs update from Tyler Hicks:
"Improve performance when AES-NI (and most likely other crypto
accelerators) is available by moving to the ablkcipher crypto API.
The improvement is more apparent on faster storage devices.
There's no noticeable change when hardware crypto is not available"
* tag 'ecryptfs-3.10-rc1-ablkcipher' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: Use the ablkcipher crypto API
Linus Torvalds [Fri, 10 May 2013 16:09:47 +0000 (09:09 -0700)]
Merge tag 'for-linus-
20130509' of git://git.infradead.org/~dwmw2/random-2.6
Pull misc fixes from David Woodhouse:
"This is some miscellaneous cleanups that don't really belong anywhere
else (or were ignored), that have been sitting in linux-next for some
time. Two of them are fixes resulting from my audit of krealloc()
usage that don't seem to have elicited any response when I posted
them, and the other three are patches from Artem removing dead code."
* tag 'for-linus-
20130509' of git://git.infradead.org/~dwmw2/random-2.6:
pcmcia: remove RPX board stuff
m68k: remove rpxlite stuff
pcmcia: remove Motorola MBX860 support
params: Fix potential memory leak in add_sysfs_param()
dell-laptop: Fix krealloc() misuse in parse_da_table()
Linus Torvalds [Fri, 10 May 2013 16:08:21 +0000 (09:08 -0700)]
Merge tag 'kvm-3.10-2' of git://git./virt/kvm/kvm
Pull kvm fixes from Gleb Natapov:
"Most of the fixes are in the emulator since now we emulate more than
we did before for correctness sake we see more bugs there, but there
is also an OOPS fixed and corruption of xcr0 register."
* tag 'kvm-3.10-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: emulator: emulate SALC
KVM: emulator: emulate XLAT
KVM: emulator: emulate AAM
KVM: VMX: fix halt emulation while emulating invalid guest sate
KVM: Fix kvm_irqfd_init initialization
KVM: x86: fix maintenance of guest/host xcr0 state
Linus Torvalds [Fri, 10 May 2013 16:02:50 +0000 (09:02 -0700)]
Merge tag 'dm-3.10-changes-2' of git://git./linux/kernel/git/agk/linux-dm
Pull device-mapper updates from Alasdair Kergon:
"Allow devices that hold metadata for the device-mapper thin
provisioning target to be extended easily; allow WRITE SAME on
multipath devices; an assortment of little fixes and clean-ups."
* tag 'dm-3.10-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm: (21 commits)
dm cache: set config value
dm cache: move config fns
dm thin: generate event when metadata threshold passed
dm persistent metadata: add space map threshold callback
dm persistent data: add threshold callback to space map
dm thin: detect metadata device resizing
dm persistent data: support space map resizing
dm thin: open dev read only when possible
dm thin: refactor data dev resize
dm cache: replace memcpy with struct assignment
dm cache: fix typos in comments
dm cache policy: fix description of lookup fn
dm: document iterate_devices
dm persistent data: fix error message typos
dm cache: tune migration throttling
dm mpath: enable WRITE SAME support
dm table: fix write same support
dm bufio: avoid a possible __vmalloc deadlock
dm snapshot: fix error return code in snapshot_ctr
dm cache: fix error return code in cache_create
...
Linus Torvalds [Fri, 10 May 2013 16:00:39 +0000 (09:00 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fix usage of sleeping lock in atomic context from Jiri Kosina
- build fix for hid-steelseries under certain .config setups by Simon Wood
- simple mismerge fix from Fernando Luis Vázquez Cao
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: debug: fix RCU preemption issue
HID: hid-steelseries fix led class build issue
HID: reintroduce fix-up for certain Sony RF receivers