Jisheng Zhang [Wed, 13 May 2020 10:26:02 +0000 (18:26 +0800)]
mmc: sdhci-of-dwcmshc: implement specific set_uhs_signaling
We need a different set_uhs_signaling implementation for
MMC_TIMING_MMC_HS and MMC_TIMING_MMC_HS400.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200513182602.3636a551@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Martin Blumenstingl [Tue, 12 May 2020 20:41:47 +0000 (22:41 +0200)]
mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host
The SDHC MMC host controller on Amlogic SoCs provides an eMMC and MMC
card interface with 1/4/8-bit bus width.
It supports eMMC spec 4.4x/4.5x including HS200 (up to 100MHz clock).
The public S805 datasheet [0] contains a short documentation about the
registers. Unfortunately it does not describe how to use the registers
to make the hardware work. Thus this driver is based on reading (and
understanding) the Amlogic 3.10 GPL kernel code.
Some hardware details are not easy to see. Jianxin Pan was kind enough
to answer my questions:
The hardware has built-in busy timeout support. The maximum timeout is
30 seconds. This is only documented in Amlogic's internal
documentation.
The controller only works with very specific clock configurations. The
details are not part of the public datasheet. In my own words the
supported configurations are:
- 399.812kHz: clkin = 850MHz div = 2126 sd_rx_phase = 63
- 1MHz: clkin = 850MHz div = 850 sd_rx_phase = 55
- 5.986MHz: clkin = 850MHz div = 142 sd_rx_phase = 24
- 25MHz: clkin = 850MHz div = 34 sd_rx_phase = 15
- 47.222MHz: clkin = 850MHz div = 18 sd_rx_phase = 11/15 (SDR50/HS)
- 53.125MHz: clkin = 850MHz div = 16 sd_rx_phase = (tuning)
- 70.833MHz: clkin = 850MHz div = 12 sd_rx_phase = (tuning)
- 85MHz: clkin = 850MHz div = 10 sd_rx_phase = (tuning)
- 94.44MHz: clkin = 850MHz div = 9 sd_rx_phase = (tuning)
- 106.25MHz: clkin = 850MHz div = 8 sd_rx_phase = (tuning)
- 127.5MHz: clkin = 1275MHz div = 10 sd_rx_phase = (tuning)
- 141.667MHz: clkin = 850MHz div = 6 sd_rx_phase = (tuning)
- 159.375MHz: clkin = 1275MHz div = 8 sd_rx_phase = (tuning)
- 212.5MHz: clkin = 1275MHz div = 6 sd_rx_phase = (tuning)
- (sd_tx_phase is always 1, 94.44MHz is not listed in the datasheet
but this is what the 3.10 BSP kernel on Odroid-C1 actually uses)
NOTE: CMD23 support is disabled for now because it results in command
timeouts and thus decreases read performance.
Tested-by: Wei Wang <lnykww@gmail.com>
Tested-by: Xin Yin <yinxin_1989@aliyun.com>
Reviewed-by: Xin Yin <yinxin_1989@aliyun.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200512204147.504087-3-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Martin Blumenstingl [Tue, 12 May 2020 20:41:46 +0000 (22:41 +0200)]
dt-bindings: mmc: Document the Amlogic Meson SDHC MMC host controller
This documents the devicetree bindings for the SDHC MMC host controller
found in Meson6, Meson8, Meson8b and Meson8m2 SoCs. It can use a
bus-width of 1/4/8-bit and it supports eMMC spec 4.4x/4.5x including
HS200 mode (up to 100MHz clock). It embeds an internal clock controller
which outputs four clocks (mod_clk, sd_clk, tx_clk and rx_clk) and is
fed by four external input clocks (clkin[0-3]). "pclk" is the module
register clock, it has to be enabled to access the registers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200512204147.504087-2-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jérôme Pouiller [Mon, 11 May 2020 16:19:02 +0000 (18:19 +0200)]
mmc: fix compilation of user API
The definitions of MMC_IOC_CMD and of MMC_IOC_MULTI_CMD rely on
MMC_BLOCK_MAJOR:
#define MMC_IOC_CMD _IOWR(MMC_BLOCK_MAJOR, 0, struct mmc_ioc_cmd)
#define MMC_IOC_MULTI_CMD _IOWR(MMC_BLOCK_MAJOR, 1, struct mmc_ioc_multi_cmd)
However, MMC_BLOCK_MAJOR is defined in linux/major.h and
linux/mmc/ioctl.h did not include it.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200511161902.191405-1-Jerome.Pouiller@silabs.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Masahiro Yamada [Mon, 11 May 2020 06:28:27 +0000 (15:28 +0900)]
mmc: sdhci: use FIELD_GET/PREP for current capabilities bit masks
Use FIELD_GET and FIELD_PREP to get access to the register fields. Delete
the shift macros and use GENMASK() for the touched macros.
Note that, this has the side-effect of changing the constants to 64-bit on
64-bit platforms.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/r/20200511062828.1791484-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Masahiro Yamada [Mon, 11 May 2020 06:21:58 +0000 (15:21 +0900)]
mmc: uniphier-sd: call devm_request_irq() after tmio_mmc_host_probe()
Currently, tmio_mmc_irq() handler is registered before the host is
fully initialized by tmio_mmc_host_probe(). I did not previously notice
this problem.
The boot ROM of a new Socionext SoC unmasks interrupts (CTL_IRQ_MASK)
somehow. The handler is invoked before tmio_mmc_host_probe(), then
emits noisy call trace.
Move devm_request_irq() below tmio_mmc_host_probe().
Fixes:
3fd784f745dd ("mmc: uniphier-sd: add UniPhier SD/eMMC controller driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200511062158.1790924-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ben Chuang [Fri, 8 May 2020 06:41:54 +0000 (14:41 +0800)]
mmc: sdhci-pci-gli: Add Genesys Logic GL9763E support
GL9763E supports High Speed SDR, High Speed DDR, HS200, HS400, Enhanced
Strobe in HS400 mode, 1/4/8 bits data bus and 3.3/1.8V.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20200508064154.13473-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Fri, 8 May 2020 11:29:02 +0000 (13:29 +0200)]
mmc: host: Drop redundant MMC_CAP_ERASE
The MMC_CAP_ERASE bit is no longer used by the mmc core as erase, discard
and trim operations are now always supported. Therefore, drop the bit and
move all mmc hosts away from using it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Link: https://lore.kernel.org/r/20200508112902.23575-1-ulf.hansson@linaro.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Ulf Hansson [Fri, 8 May 2020 11:28:53 +0000 (13:28 +0200)]
mmc: core: Enable erase/discard/trim support for all mmc hosts
Step by step, mmc host drivers and the mmc core have been improved in
regards to support erase/discard/trim operations. We have now reached a
point when it no longer seems reasonable to use an opt-in approach to
enable the functionality. Therefore, let's switch to make the operations
always supported.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200508112853.23525-1-ulf.hansson@linaro.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Ulf Hansson [Fri, 8 May 2020 09:52:28 +0000 (11:52 +0200)]
mmc: sdricoh_cs: Respect the cmd->busy_timeout from the mmc core
Using a fixed 1s polling timeout for all commands is a bit problematic.
For some commands it means waiting longer than needed for the polling to be
aborted, which may not a big issue, but still. For other commands, like for
an erase (CMD38) that uses a R1B response, may require longer timeouts than
1s. In these cases, we may end up treating the command as it failed, while
it just needed some more time to complete successfully.
Fix the problem by respecting the cmd->busy_timeout, which is provided by
the mmc core.
Note that, even if the sdricoh_cs driver may currently not support HW busy
detection on DAT0, some comments in the code refer to that the HW may
support it. Therefore, it seems better to be proactive in this case.
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200508095228.14230-1-ulf.hansson@linaro.org
Ulf Hansson [Fri, 8 May 2020 09:52:18 +0000 (11:52 +0200)]
mmc: sdricoh_cs: Throttle polling rate for commands
Rather than to poll in a busy-loop, let's convert into using
read_poll_timeout() and insert a small delay between each polling attempts.
In particular, this avoids hogging the CPU.
Additionally, to convert to read_poll_timeout() we also need to switch from
using a specific number of polling attempts, into a specific timeout in us
instead. The previous 100000 attempts, is translated into a total timeout
of total 1s, as that seemed like reasonable value to pick.
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200508095218.14177-1-ulf.hansson@linaro.org
Ulf Hansson [Fri, 8 May 2020 09:52:10 +0000 (11:52 +0200)]
mmc: sdricoh_cs: Throttle polling rate for data transfers
Rather than to poll in a busy-loop, let's convert into using
read_poll_timeout() and insert a small delay between each polling attempts.
In particular, this avoids hogging the CPU.
Additionally, to convert to read_poll_timeout() we also need to switch from
using a specific number of polling attempts, into a specific timeout in us
instead. The previous 100000 attempts, is translated into a total timeout
of total 1s, as that seemed like reasonable value to pick.
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200508095210.14123-1-ulf.hansson@linaro.org
Ulf Hansson [Tue, 14 Apr 2020 16:14:00 +0000 (18:14 +0200)]
mmc: cb710: Inform the mmc core about the maximum busy timeout
Some commands uses R1B responses, which means the card may assert the DAT0
line to signal busy for a period of time, after it has received the
command. The mmc core normally specifies the busy period for the command in
the cmd->busy_timeout. Ideally the driver should respect it, but that
requires quite some update of the code, so let's defer that to someone with
the HW at hand.
Instead, let's inform the mmc core about the maximum supported busy timeout
in ->max_busy_timeout during ->probe(). This value corresponds to the fixed
~2s timeout of the polling loop, implemented in cb710_wait_for_event(). In
this way, we let the mmc core validate the needed timeout, which may lead
to that it converts from a R1B into a R1 response and then use CMD13 to
poll for busy completion.
In other words, this change enables support for commands with longer busy
periods than 2s, like erase (CMD38) for example.
Cc: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-7-ulf.hansson@linaro.org
Gustavo A. R. Silva [Thu, 7 May 2020 19:22:18 +0000 (14:22 -0500)]
memstick: Replace zero-length array with flexible-array
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit
76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200507192218.GA16315@embeddedor
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Martin Blumenstingl [Sun, 3 May 2020 22:28:05 +0000 (00:28 +0200)]
mmc: meson-mx-sdio: trigger a soft reset after a timeout or CRC error
The vendor driver (from the 3.10 kernel) triggers a soft reset every
time before starting a new command. While this fixes a problem where
SDIO cards are not detected at all (because all commands simply
timed out) this hurts SD card read performance a bit (in my tests
between 10% to 20%).
Trigger a soft reset after we got a CRC error or if the previous command
timed out (just like the vendor driver from the same 3.10 kernel for the
newer SDHC controller IP does). This fixes detection of SDIO cards and
doesn't hurt SD card read performance at the same time.
With this patch the initialization of an RTL8723BS SDIO card looks like
this:
req done (CMD52): -110:
00000000 00000000 00000000 00000000
clock 400000Hz busmode 2 powermode 2 cs 1 Vdd 21 width 1 timing 0
starting CMD0 arg
00000000 flags
000000c0
req done (CMD0): 0:
00000000 00000000 00000000 00000000
clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 0
starting CMD8 arg
000001aa flags
000002f5
req done (CMD8): -110:
00000000 00000000 00000000 00000000
starting CMD5 arg
00000000 flags
000002e1
req done (CMD5): 0:
90ff0000 00000000 00000000 00000000
starting CMD5 arg
00200000 flags
000002e1
req done (CMD5): 0:
90ff0000 00000000 00000000 00000000
starting CMD3 arg
00000000 flags
00000075
req done (CMD3): 0:
00010000 00000000 00000000 00000000
starting CMD7 arg
00010000 flags
00000015
req done (CMD7): 0:
00001e00 00000000 00000000 00000000
starting CMD52 arg
00000000 flags
00000195
req done (CMD52): 0:
00001032 00000000 00000000 00000000
[... more CMD52 omitted ...]
clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 2
clock 50000000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 2
starting CMD52 arg
00000e00 flags
00000195
req done (CMD52): 0:
00001000 00000000 00000000 00000000
starting CMD52 arg
80000e02 flags
00000195
req done (CMD52): 0:
00001002 00000000 00000000 00000000
clock 50000000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 4 timing 2
starting CMD52 arg
00020000 flags
00000195
req done (CMD52): 0:
00001007 00000000 00000000 00000000
[... more CMD52 omitted ...]
new high speed SDIO card at address 0001
Fixes:
ed80a13bb4c4c9 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20200503222805.2668941-1-martin.blumenstingl@googlemail.com
Tested-by: Tobias Baumann <017623705678@o2online.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Lad Prabhakar [Wed, 6 May 2020 19:51:27 +0000 (20:51 +0100)]
dt-bindings: mmc: renesas,mmcif: Document r8a7742 DT bindings
Add support for r8a7742 SoC. Renesas RZ/G1H (R8A7742) MMCIF is identical
to the R-Car Gen2 family.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1588794695-27852-2-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wolfram Sang [Sat, 2 May 2020 14:28:25 +0000 (16:28 +0200)]
mmc: sdhci-esdhc: update contact email
The 'pengutronix' address is defunct for years. Use the proper contact
address.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200502142840.19418-1-wsa@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Krishna Konda [Fri, 1 May 2020 13:53:01 +0000 (19:23 +0530)]
mmc: core: expose info about enhanced rpmb support
Following eMMC JEDEC JESD84-B51 standard, an enhanced form of
rpmb is supported. What this enhanced mode supports is in addition
to be able to write one rpmb or two rpmb frames at a time,
32 frames can be written at a time.
Expose this information present in ext csd field so that the
user space application that wants to make use of this can do so.
Signed-off-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1588341189-4371-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Thu, 30 Apr 2020 09:16:40 +0000 (11:16 +0200)]
mmc: sdio: Align the initialization commands in retry path for UHS-I
According to the comment in mmc_sdio_reinit_card(), some SDIO cards may
require a "[CMD5,5,3,7] init sequence", which isn't always obeyed in
mmc_sdio_init_card(). Especially, when we end up retrying the UHS-I
specific initialization, there is a missing CMD5.
Let's update the code to make the behaviour consistent and let's also take
the opportunity to clean up the code a bit, to avoid open coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200430091640.455-5-ulf.hansson@linaro.org
Ulf Hansson [Thu, 30 Apr 2020 09:16:39 +0000 (11:16 +0200)]
mmc: sdio: Re-use negotiated OCR mask when re-sending CMD8
While initializing an SDIO card in mmc_sdio_init_card(), we may need to
retry the UHS-I specific initialization, in case the first attempt fails.
This leads to resending a CMD8, but also to restart from scratch with the
so called OCR mask negotiations. This is unnecessary as we already have a
negotiated OCR mask, so let's use that instead. In this way, the behaviour
also becomes more consistent with other similar paths.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200430091640.455-4-ulf.hansson@linaro.org
Ulf Hansson [Thu, 30 Apr 2020 09:16:38 +0000 (11:16 +0200)]
mmc: sdio: Fix several potential memory leaks in mmc_sdio_init_card()
Over the years, the code in mmc_sdio_init_card() has grown to become quite
messy. Unfortunate this has also lead to that several paths are leaking
memory in form of an allocated struct mmc_card, which includes additional
data, such as initialized struct device for example.
Unfortunate, it's a too complex task find each offending commit. Therefore,
this change fixes all memory leaks at once.
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200430091640.455-3-ulf.hansson@linaro.org
Ulf Hansson [Thu, 30 Apr 2020 09:16:37 +0000 (11:16 +0200)]
mmc: sdio: Fix potential NULL pointer error in mmc_sdio_init_card()
During some scenarios mmc_sdio_init_card() runs a retry path for the UHS-I
specific initialization, which leads to removal of the previously allocated
card. A new card is then re-allocated while retrying.
However, in one of the corresponding error paths we may end up to remove an
already removed card, which likely leads to a NULL pointer exception. So,
let's fix this.
Fixes:
5fc3d80ef496 ("mmc: sdio: don't use rocr to check if the card could support UHS mode")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200430091640.455-2-ulf.hansson@linaro.org
Rajendra Nayak [Tue, 28 Apr 2020 13:32:57 +0000 (19:02 +0530)]
mmc: sdhci-msm: Fix error handling for dev_pm_opp_of_add_table()
Even though specifying OPP's in device tree is optional, ignoring all errors
reported by dev_pm_opp_of_add_table() means we can't distinguish between a
missing OPP table and a wrong/buggy OPP table. While missing OPP table
(dev_pm_opp_of_add_table() returns a -ENODEV in such case) can be ignored,
a wrong/buggy OPP table in device tree should make the driver error out.
while we fix that, lets also fix the variable names for opp/opp_table to
avoid confusion and name them opp_table/has_opp_table instead.
Suggested-by: Matthias Kaehlcke <matthias@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1588080785-6812-10-git-send-email-rnayak@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Takeshi Saito [Thu, 23 Apr 2020 13:04:32 +0000 (15:04 +0200)]
mmc: renesas_sdhi: Avoid bad TAP in HS400
With R-Car Gen3, CRC error occue at the following TAPs.
H3, M3W 1.3, M3N... TAP=2,3,6,7
M3W 3.0 ... TAP=1,3,5,7
(Note: for 4tap SoCs, the numbers get divided by 2)
Do not use these TAPs in HS400, and also don't use auto correction but
manual correction.
We check for bad taps in two places:
1) After tuning HS400: Then, we select a neighbouring TAP. One of them
must be good, because there are never three bad taps in a row.
Retuning won't help because we just finished tuning.
2) After a manual correction request: Here, we can't switch to the
requested TAP. But we can retune (if the HS200 tuning was good)
because the environment might have changed since the last tuning.
If not, we stay on the same TAP.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: refactored to match upstream driver, reworded commit msg]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200423130432.9990-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wolfram Sang [Thu, 23 Apr 2020 13:04:31 +0000 (15:04 +0200)]
mmc: renesas_sdhi: handle M3-W ES1.2 and 1.3 revisions
For ES1.2, add a comment explaining the situation. For ES1.3 (and
later, although unlikely), add a new entry defining it as 4tap.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200423130432.9990-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Tue, 14 Apr 2020 16:14:12 +0000 (18:14 +0200)]
mmc: mmc_spi: Respect the cmd->busy_timeout from the mmc core
Using a fixed 3s polling timeout for all commands with R1B responses is a
bit problematic.
For some commands it means waiting longer than needed for the polling to be
aborted, which may not a big issue, but still. For other commands, like for
an erase (CMD38), may require longer timeouts than 3s. In these cases, we
may end up treating the command as it failed, while it just needed some
more time to complete successfully.
Fix the problem by respecting the cmd->busy_timeout, which is provided by
the mmc core.
Cc: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-19-ulf.hansson@linaro.org
Ulf Hansson [Tue, 14 Apr 2020 16:14:11 +0000 (18:14 +0200)]
mmc: mmc_spi: Add/rename defines for timeouts
Clarify the use of r1b_timeout, by renaming it to MMC_SPI_R1B_TIMEOUT_MS
and by dropping the corresponding confusing comment about it.
Additionally, let's also add a new define, MMC_SPI_INIT_TIMEOUT_MS and use
it during the initialization. Even if these two defines are given the same
value, the split makes it easier to understand them.
Cc: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-18-ulf.hansson@linaro.org
Ulf Hansson [Tue, 14 Apr 2020 16:14:10 +0000 (18:14 +0200)]
mmc: via-sdmmc: Respect the cmd->busy_timeout from the mmc core
Using a fixed 1s timeout for all commands (and data transfers) is a bit
problematic.
For some commands it means waiting longer than needed for the timer to
expire, which may not a big issue, but still. For other commands, like for
an erase (CMD38) that uses a R1B response, may require longer timeouts than
1s. In these cases, we may end up treating the command as it failed, while
it just needed some more time to complete successfully.
Fix the problem by respecting the cmd->busy_timeout, which is provided by
the mmc core.
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-17-ulf.hansson@linaro.org
Ulf Hansson [Tue, 14 Apr 2020 16:14:09 +0000 (18:14 +0200)]
mmc: tifm_sd: Inform the mmc core about the maximum busy timeout
Some commands uses R1B responses, which means the card may assert the DAT0
line to signal busy for a period of time, after it has received the
command. The mmc core normally specifies the busy period for the command in
the cmd->busy_timeout. Ideally the driver should respect it, but that
requires quite some update of the code, so let's defer that to someone with
the HW at hand.
Instead, let's inform the mmc core about the maximum supported busy timeout
in ->max_busy_timeout during ->probe(). This value corresponds to the fixed
1s timeout used by tifm_sd. In this way, we let the mmc core validate the
needed timeout, which may lead to that it converts from a R1B into a R1
response and then use CMD13 to poll for busy completion.
In other words, this change enables support for commands with longer busy
periods than 1s, like erase (CMD38) for example.
Cc: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-16-ulf.hansson@linaro.org
Ulf Hansson [Tue, 14 Apr 2020 16:14:05 +0000 (18:14 +0200)]
mmc: sdricoh_cs: Drop redundant in-parameter to sdricoh_query_status()
The in-parameter timeout is always set to TRANSFER_TIMEOUT by the callers
of sdricoh_query_status(), hence let's drop it.
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-12-ulf.hansson@linaro.org
Ulf Hansson [Tue, 14 Apr 2020 16:14:04 +0000 (18:14 +0200)]
mmc: sdricoh_cs: Move MMC_APP_CMD handling to sdricoh_mmc_cmd()
Move MMC_APP_CMD specific handling to be managed by sdricoh_mmc_cmd(), as
this makes the code a bit cleaner.
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-11-ulf.hansson@linaro.org
Ulf Hansson [Tue, 14 Apr 2020 16:14:03 +0000 (18:14 +0200)]
mmc: sdricoh_cs: Use MMC_APP_CMD rather than a hardcoded number
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-10-ulf.hansson@linaro.org
Ulf Hansson [Tue, 14 Apr 2020 16:14:02 +0000 (18:14 +0200)]
mmc: sdricoh_cs: Drop unused defines
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-9-ulf.hansson@linaro.org
Ulf Hansson [Tue, 14 Apr 2020 16:14:01 +0000 (18:14 +0200)]
mmc: owl-mmc: Respect the cmd->busy_timeout from the mmc core
For commands that doesn't involve to prepare a data transfer, owl-mmc is
using a fixed 30s response timeout. This is a bit problematic.
For some commands it means waiting longer than needed for the completion to
expire, which may not a big issue, but still. For other commands, like for
an erase (CMD38) that uses a R1B response, may require longer timeouts than
30s. In these cases, we may end up treating the command as it failed, while
it just needed some more time to complete successfully.
Fix the problem by respecting the cmd->busy_timeout, which is provided by
the mmc core.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-8-ulf.hansson@linaro.org
Ulf Hansson [Tue, 14 Apr 2020 16:13:58 +0000 (18:13 +0200)]
mmc: jz4740: Inform the mmc core about the maximum busy timeout
Some commands uses R1B responses, which means the card may assert the DAT0
line to signal busy for a period of time, after it has received the
command. The mmc core normally specifies the busy period for the command in
the cmd->busy_timeout. Ideally the driver should respect it, but that
requires quite some update of the code, so let's defer that to someone with
the HW at hand.
Instead, let's inform the mmc core about the maximum supported busy timeout
in ->max_busy_timeout during ->probe(). This value corresponds to the fixed
5s timeout used by jz4740. In this way, we let the mmc core validate the
needed timeout, which may lead to that it converts from a R1B into a R1
response and then use CMD13 to poll for busy completion.
In other words, this change enables support for commands with longer busy
periods than 5s, like erase (CMD38) for example.
Cc: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-5-ulf.hansson@linaro.org
Zou Wei [Thu, 23 Apr 2020 06:43:19 +0000 (14:43 +0800)]
mmc: sdhci-pci-o2micro: Make some symbols static
Fix the following sparse warning:
drivers/mmc/host/sdhci-pci-o2micro.c:497:6: warning: symbol
'sdhci_pci_o2_set_clock' was not declared. Should it be static?
drivers/mmc/host/sdhci-pci-o2micro.c:512:5: warning: symbol
'sdhci_pci_o2_probe_slot' was not declared. Should it be static?
drivers/mmc/host/sdhci-pci-o2micro.c:581:5: warning: symbol
'sdhci_pci_o2_probe' was not declared. Should it be static?
drivers/mmc/host/sdhci-pci-o2micro.c:786:5: warning: symbol
'sdhci_pci_o2_resume' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1587624199-96926-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Zou Wei [Thu, 23 Apr 2020 09:15:19 +0000 (17:15 +0800)]
mmc: core: Use DEFINE_DEBUGFS_ATTRIBUTE instead of DEFINE_SIMPLE_ATTRIBUTE
Fixes coccicheck warning:
drivers/mmc/core/debugfs.c:222:0-23: WARNING: mmc_clock_fops should be
defined with DEFINE_DEBUGFS_ATTRIBUTE
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files
Fixes:
703aae3d09a4b ("mmc: add a file to debugfs for changing host clock at runtime")
Fixes:
a04c50aaa916f ("mmc: core: no need to check return value of debugfs_create functions")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1587633319-19835-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Masahiro Yamada [Wed, 22 Apr 2020 15:34:01 +0000 (00:34 +0900)]
mmc: sdhci-of-at91: make MMC_SDHCI_OF_AT91 depend on HAVE_CLK
If sdhci-of-at91.c is compiled without CONFIG_HAVE_CLK, the line
caps1 |= FIELD_PREP(SDHCI_CLOCK_MUL_MASK, clk_mul);
... emits "FIELD_PREP: value too large for the field" warning.
The compiler seems to decide clk_mul is constant (unsigned int)-1,
because clk_get_rate() returns 0 when CONFIG_HAVE_CLK is disabled.
Add HAVE_CLK to the depenency since this driver does not work without
the clock APIs anyway.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/r/20200422153401.7913-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Wolfram Sang [Mon, 20 Apr 2020 17:02:30 +0000 (19:02 +0200)]
mmc: renesas_sdhi: shorten types after refactorization
After TAP refactorization, we can use 'unsigned int' for two more
variables because all the calculations work on this type now.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200420170230.9091-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ludovic Barre [Mon, 20 Apr 2020 16:18:31 +0000 (18:18 +0200)]
mmc: mmci_sdmmc: fix power on issue due to pwr_reg initialization
This patch fix a power-on issue, and avoid to retry the power sequence.
In power off sequence: sdmmc must set pwr_reg in "power-cycle" state
(value 0x2), to prevent the card from being supplied through the signal
lines (all the lines are driven low).
In power on sequence: when the power is stable, sdmmc must set pwr_reg
in "power-off" state (value 0x0) to drive all signal to high before to
set "power-on".
To avoid writing the same value to the power register several times, this
register is cached by the pwr_reg variable. At probe pwr_reg is initialized
to 0 by kzalloc of mmc_alloc_host.
Like pwr_reg value is 0 at probing, the power on sequence fail because
the "power-off" state is not writes (value 0x0) and the lines
remain drive to low.
This patch initializes "pwr_reg" variable with power register value.
This it done in sdmmc variant init to not disturb default mmci behavior.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200420161831.5043-1-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rajendra Nayak [Fri, 17 Apr 2020 14:04:31 +0000 (19:34 +0530)]
mmc: sdhci-msm: Use OPP API to set clk/perf state
On some qualcomm SoCs we need to vote on a performance state of a power
domain depending on the clock rates. Hence move to using OPP api to set
the clock rate and performance state specified in the OPP table.
On platforms without an OPP table, dev_pm_opp_set_rate() is eqvivalent to
clk_set_rate()
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1587132279-27659-10-git-send-email-rnayak@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Tue, 14 Apr 2020 16:14:13 +0000 (18:14 +0200)]
staging: greybus: sdio: Respect the cmd->busy_timeout from the mmc core
Using a fixed 1s timeout for all commands is a bit problematic.
For some commands it means waiting longer than needed for the timeout to
expire, which may not a big issue, but still. For other commands, like for
an erase (CMD38) that uses a R1B response, may require longer timeouts than
1s. In these cases, we may end up treating the command as it failed, while
it just needed some more time to complete successfully.
Fix the problem by respecting the cmd->busy_timeout, which is provided by
the mmc core.
Cc: Rui Miguel Silva <rmfrfs@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: greybus-dev@lists.linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200414161413.3036-20-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Tue, 14 Apr 2020 16:13:59 +0000 (18:13 +0200)]
mmc: usdhi6rol0: Inform the mmc core about the maximum busy timeout
Some commands uses R1B responses, which means the card may assert the DAT0
line to signal busy for a period of time, after it has received the
command. The mmc core normally specifies the busy period for the command in
the cmd->busy_timeout. Ideally the driver should respect it, but that
requires quite some update of the code, so let's defer that to someone with
the HW at hand.
Instead, let's inform the mmc core about the maximum supported busy timeout
in ->max_busy_timeout during ->probe(). This value corresponds to the fixed
4s timeout used by usdhi6rol0. In this way, we let the mmc core validate
the needed timeout, which may lead to that it converts from a R1B into a R1
response and then use CMD13 to poll for busy completion.
In other words, this change enables support for commands with longer busy
periods than 4s, like erase (CMD38) for example.
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Lars Persson <lars.persson@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Link: https://lore.kernel.org/r/20200414161413.3036-6-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Tue, 14 Apr 2020 16:13:57 +0000 (18:13 +0200)]
mmc: atmel-mci: Respect the cmd->busy_timeout from the mmc core
Using a fixed 2s timeout for all commands is a bit problematic.
For some commands it means waiting longer than needed for the timer to
expire, which may not a big issue, but still. For other commands, like for
an erase (CMD38) that uses a R1B response, may require longer timeouts than
2s. In these cases, we may end up treating the command as it failed, while
it just needed some more time to complete successfully.
Fix the problem by respecting the cmd->busy_timeout, which is provided by
the mmc core.
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20200414161413.3036-4-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Tue, 14 Apr 2020 16:13:56 +0000 (18:13 +0200)]
mmc: atmel-mci: Set the timer per command rather than per request
Setting the timer on a per request basis, is rather limiting as the timer
really depends on what commands that is to be sent as part of the request.
Therefore improve the behaviour by programming the timer per command basis
instead.
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20200414161413.3036-3-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Tue, 14 Apr 2020 16:13:55 +0000 (18:13 +0200)]
mmc: atmel-mci: Keep timer enabled when queuing a next request
When atmci_request_end() is about to finish a request for one slot, there
is a possibility that there is new request queued for another slot. If this
turns out to be the case, the new request is started and the timer is
re-programmed for it.
Although, a few lines below in atmci_request_end(), this timer becomes
deleted, likely corresponding to the other recently completed request. This
looks wrong, so let's fix it.
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20200414161413.3036-2-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Veerabhadrarao Badiganti [Mon, 20 Apr 2020 06:20:25 +0000 (11:50 +0530)]
mmc: sdhci-msm: Enable ADMA length mismatch error interrupt
ADMA_ERR_SIZE_EN bit of VENDOR_SPECIFIC_FUNC register controls
ADMA length mismatch error interrupt. Enable it by default.
And update all bit shift defines with BIT macro.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1587363626-20413-4-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Veerabhadrarao Badiganti [Mon, 20 Apr 2020 06:20:24 +0000 (11:50 +0530)]
mmc: sdhci-msm: Set SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12 quirk
sdhci-msm can support auto cmd12.
So enable SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12 quirk.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1587363626-20413-3-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Haibo Chen [Wed, 15 Apr 2020 09:00:55 +0000 (17:00 +0800)]
mmc: sdhci: add spin lock for sdhci_set_default_irqs in sdhci_init
When use one SDIO wifi which enable the runtime PM feature on i.MX6SX,
we meet system hang. This hang happened during the usdhc runtime resume,
in sdhci_init(), when call the sdhci_set_default_irqs. One interrupt
(SDHCI_INT_CARD_INT) triggered just after the host->ier update and before
the write of register SDHCI_SIGNAL_ENABLE. So in sdhci_irq, it will skip
the call of sdio_signal_irq() because current host->ier do not set the
SDHCI_INT_CARD_INT. So this SDIO wifi interrupt always keep triggered,
let the system stuck in irq handle, can't response any other thread.
This patch add spin lock for the sdhci_set_default_irqs to fix this issue.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1586941255-9237-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Baolin Wang [Mon, 13 Apr 2020 02:46:05 +0000 (10:46 +0800)]
mmc: host: sdhci-sprd: Implement the request_atomic() API
Implement the request_atomic() API for nonremovable cards, that means
we can submit next request in the irq hard handler context to reduce
latency.
Moreover factor out the AUTO CMD23 checking into a separate function
to reduce duplicate code.
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/60142fe6c6c1dbba2696e775564ae2166786f0bc.1586744073.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Baolin Wang [Mon, 13 Apr 2020 02:46:04 +0000 (10:46 +0800)]
mmc: host: sdhci: Implement the request_atomic() API
Implement the request_atomic() ops for the sdhci driver to process
one request in the atomic context if the card is nonremovable.
Moreover, we should return BUSY flag if controller has not released
the inhibit bits to allow HSQ trying to send request again in non-atomic
context.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/9ed34afa9fb42e0c234065cac5401d7826942b55.1586744073.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Baolin Wang [Mon, 13 Apr 2020 02:46:03 +0000 (10:46 +0800)]
mmc: host: Introduce the request_atomic() for the host
The SD host controller can process one request in the atomic context if
the card is nonremovable, which means we can submit next request in the
irq hard handler when using the MMC host software queue to reduce the
latency. Thus this patch adds a new API request_atomic() for the host
controller, as well as adding support for host software queue to submit
a request by the new request_atomic() API.
Moreover there is an unusual case that the card is busy when trying to
send a command, and we can not polling the card status in interrupt
context by using request_atomic() to dispatch requests. Thus we should
queue a work to try again in the non-atomic context in case the host
releases the busy signal later.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/a344e27e506cb2329073cbd5cf65e15cc3cbeba9.1586744073.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Sun, 12 Apr 2020 09:03:49 +0000 (12:03 +0300)]
mmc: sdhci: Reduce maximum time under spinlock in sdhci_send_command()
Spending time under spinlock increases IRQ latencies and also
response times because preemption is disabled.
sdhci_send_command() waits up to 10 ms under spinlock for inhibit bits
to clear. In general inhibit bits will not be set, but there may be
corner cases, especially in the face of errors, where waiting helps.
There might also be dysfunctional hardware that needs the waiting. So
retain the legacy behaviour but do not wait for inhibit bits while under
spinlock. Instead adjust the logic to enable waiting while not under
spinlock. That is mostly straight forward, but in the interrupt handler
it requires deferring an "inhibited" command to the IRQ thread where
sleeping is allowed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200412090349.1607-6-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Sun, 12 Apr 2020 09:03:48 +0000 (12:03 +0300)]
mmc: sdhci: Tidy sdhci_request() a bit
In preparation for further changes, tidy sdhci_request() a bit.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200412090349.1607-5-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Sun, 12 Apr 2020 09:03:47 +0000 (12:03 +0300)]
mmc: sdhci: Remove unneeded forward declaration of sdhci_finish_data()
sdhci_finish_data() is defined before it is referenced, so forward
declaration is not necessary.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200412090349.1607-4-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Sun, 12 Apr 2020 09:03:46 +0000 (12:03 +0300)]
mmc: sdhci: Stop exporting sdhci_send_command()
sdhci_send_command() has not been used outside of sdhci.c for many
years. Stop exporting it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200412090349.1607-3-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Sun, 12 Apr 2020 09:03:45 +0000 (12:03 +0300)]
mmc: sdhci: Add helpers for the auto-CMD23 flag
Add 2 helper functions to make the use of the auto-CMD23 flag more
readable.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200412090349.1607-2-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jisheng Zhang [Fri, 10 Apr 2020 06:57:12 +0000 (14:57 +0800)]
mmc: sd: use HIGH_SPEED_BUS_SPEED in mmc_sd_switch_hs()
Use the well defined HIGH_SPEED_BUS_SPEED macro in mmc_sd_switch_hs()
to make code more readable.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200410145643.630b0731@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Marek Vasut [Thu, 16 Apr 2020 16:36:49 +0000 (18:36 +0200)]
mmc: mmci: Switch to mmc_regulator_set_vqmmc()
Instead of reimplementing the logic in mmc_regulator_set_vqmmc(), use the
mmc code function directly.
This also allows us to fix a related issue on STM32MP1, when a voltage
switch of 1.8V is done for the eMMC, but the current level is already set
to 1.8V. More precisely, in this scenario the call to the
->post_sig_volt_switch() hangs, indefinitely waiting for the voltage switch
to complete. Fix this problem by checking if mmc_regulator_set_vqmmc()
returned 1 and then skip invoking the callback.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200416163649.336967-3-marex@denx.de
[Ulf: Updated the commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Marek Vasut [Thu, 16 Apr 2020 16:36:48 +0000 (18:36 +0200)]
mmc: core: Return 1 from mmc_regulator_set_vqmmc() if switch skipped
Adjust mmc_regulator_set_vqmmc() to return 1 if the voltage switch was
skipped because the regulator voltage was already correct. This allows
drivers to detect such condition and possibly skip various voltage
switching extras.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200416163649.336967-2-marex@denx.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Marek Vasut [Thu, 16 Apr 2020 16:36:47 +0000 (18:36 +0200)]
mmc: host: Prepare host drivers for mmc_regulator_set_vqmmc() returning > 0
Patch all drivers which use mmc_regulator_set_vqmmc() and prepare them for
the fact that mmc_regulator_set_vqmmc() can return a value > 0, which would
happen if the signal voltage switch did NOT happen, because the voltage was
already set correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200416163649.336967-1-marex@denx.de
[Ulf: Re-worked/simplified the code a bit]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Nathan Chancellor [Thu, 16 Apr 2020 18:24:02 +0000 (11:24 -0700)]
mmc: sdhci-of-arasan: Remove uninitialized ret variables
Clang warns:
drivers/mmc/host/sdhci-of-arasan.c:784:9: warning: variable 'ret' is
uninitialized when used here [-Wuninitialized]
return ret;
^~~
drivers/mmc/host/sdhci-of-arasan.c:738:9: note: initialize the variable
'ret' to silence this warning
int ret;
^
= 0
drivers/mmc/host/sdhci-of-arasan.c:860:9: warning: variable 'ret' is
uninitialized when used here [-Wuninitialized]
return ret;
^~~
drivers/mmc/host/sdhci-of-arasan.c:810:9: note: initialize the variable
'ret' to silence this warning
int ret;
^
= 0
2 warnings generated.
This looks like a copy paste error. Neither function has handling that
needs ret so just remove it and return 0 directly.
Link: https://github.com/ClangBuiltLinux/linux/issues/996
Reported-by: kernelci.org bot <bot@kernelci.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20200416182402.16858-1-natechancellor@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wolfram Sang [Wed, 8 Apr 2020 14:22:52 +0000 (16:22 +0200)]
mmc: renesas_sdhi: simplify summary output
No need to call platform_get_resource twice when we still have the
pointer from before. Also, use '%pa' for a resource_size_t pointer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200408142252.21958-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Wolfram Sang [Wed, 8 Apr 2020 09:46:38 +0000 (11:46 +0200)]
mmc: renesas_sdhi: improve TAP selection if all TAPs are good
When tuning HS400, if all TAPS are good, we can utilize the SMPCMP
register to select the optimal TAP. For that, we populate a second
bitmap with SMPCMP results and query it in case the regular bitmap is
full (= all good).
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200408094638.10375-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wolfram Sang [Wed, 8 Apr 2020 09:46:37 +0000 (11:46 +0200)]
mmc: renesas_sdhi: clarify handling of selecting TAPs
The comment and the define about how TAPs are selected were confusing to
me because the good TAP was only valid if it was bigger than a *_MAX_*
value. Rename the define and adapt the comment to what really happens.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200408094638.10375-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wolfram Sang [Wed, 8 Apr 2020 09:46:36 +0000 (11:46 +0200)]
mmc: renesas_sdhi: refactor calculation of best TAP
To select the best TAP, we need to find the longest stream of set bits
in a bit field. There is now a helper function for bitmaps which
iterates over all region of set bits. Using it makes the code much more
concise and easier to understand. Double so, because we need to handle
two bitmaps in the near future. Remove a superfluous comment while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200408094638.10375-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Masahiro Yamada [Wed, 8 Apr 2020 07:21:05 +0000 (16:21 +0900)]
mmc: sdhci: use FIELD_GET/PREP for capabilities bit masks
Use FIELD_GET and FIELD_PREP to get access to the register fields. Delete
the shift macros and use GENMASK() for the touched macros.
Note that, this has the side-effect of changing the constants to 64-bit on
64-bit platforms.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200408072105.422-2-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Masahiro Yamada [Wed, 8 Apr 2020 07:21:04 +0000 (16:21 +0900)]
mmc: sdhci: move SDHCI_CAPABILITIES_1 to a more suitable place
In the SDHCI specification, the Capabilities Register (Offset 0x40h)
is the 64-bit width register, but in Linux, it is represented as two
registers, SDHCI_CAPABILITIES and SDHCI_CAPABILITIES_1 so that drivers
can use 32-bit register accessors.
The upper 32-bit field is associated with SDHCI_CAPABILITIES_1.
Move the definition of SDHCI_CAPABILITIES_1 to the correct place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200408072105.422-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Manish Narani [Mon, 6 Apr 2020 17:43:35 +0000 (23:13 +0530)]
mmc: sdhci-of-arasan: Fix kernel-doc warnings
Modify code to fix the warnings reported by kernel-doc for better
documentation.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1586195015-128992-7-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Manish Narani [Mon, 6 Apr 2020 17:43:34 +0000 (23:13 +0530)]
mmc: sdhci-of-arasan: Modify clock operations handling
The SDHCI clock operations are platform specific. So it better to define
them separately for particular platform. This will prevent multiple
if..else conditions and will make it easy for user to add their own
clock operations handlers.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1586195015-128992-6-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Manish Narani [Mon, 6 Apr 2020 17:43:33 +0000 (23:13 +0530)]
mmc: sdhci-of-arasan: Rearrange the platform data structs for modularity
Existing driver code has the platform specific structures scattered
throughout the driver code. Rearrange the platform specific data
structures for more modularity and readability. This will help in adding
new static functions with more ease.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1586195015-128992-5-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Manish Narani [Mon, 6 Apr 2020 17:43:32 +0000 (23:13 +0530)]
mmc: sdhci-of-arasan: Rename sdhci_arasan_data to avoid confusion
There is 'struct sdhci_arasan_data' but also
'struct sdhci_arasan_of_data sdhci_arasan_data'. Rename the latter to
avoid confusion with the name of the struct.
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1586195015-128992-4-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Manish Narani [Mon, 6 Apr 2020 17:43:31 +0000 (23:13 +0530)]
sdhci: arasan: Add support for Versal Tap Delays
Add support to set tap delays for Xilinx Versal SD controller. The tap
delay registers have moved to SD controller space in Versal. Make the
changes accordingly.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1586195015-128992-3-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Manish Narani [Mon, 6 Apr 2020 17:43:30 +0000 (23:13 +0530)]
dt-bindings: mmc: arasan: Document 'xlnx,versal-8.9a' controller
Add documentation for 'xlnx,versal-8.9a' SDHCI controller followed by
example.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1586195015-128992-2-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Thu, 9 Apr 2020 12:54:22 +0000 (14:54 +0200)]
mmc: wbsd: Replace hardcoded command numbers with existing defines
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200409125422.21842-1-ulf.hansson@linaro.org
Ulf Hansson [Tue, 7 Apr 2020 14:39:03 +0000 (16:39 +0200)]
mmc: s3cmci: Drop redundant code in s3cmci_setup_data()
The in-parameter struct mmc_data *data is never NULL, because the caller
always provides a valid pointer. Hence drop the corresponding redundant
code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200407143903.22477-1-ulf.hansson@linaro.org
Ulf Hansson [Mon, 6 Apr 2020 11:43:37 +0000 (13:43 +0200)]
mmc: au1xmmc: Drop redundant code in au1xmmc_send_command()
The in-parameter "wait" is always set to 0 by the caller, hence just drop
it and its corresponding code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Link: https://lore.kernel.org/r/20200406114337.8802-1-ulf.hansson@linaro.org
Ulf Hansson [Mon, 6 Apr 2020 11:37:24 +0000 (13:37 +0200)]
mmc: sdhci-sprd: Drop redundant cap flags
The MMC_CAP_ERASE and MMC_CAP_CMD23 flags are already being set in the
common sdhci_setup_host(). This makes it redundant to set them for
sdhci-sprd, so let's drop them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200406113724.8504-1-ulf.hansson@linaro.org
Ulf Hansson [Wed, 1 Apr 2020 14:55:31 +0000 (16:55 +0200)]
mmc: android-goldfish: Enable MMC_CAP2_NO_SDIO
Instead of explicitly checking for SDIO specific requests and then
returning an error code, let's set MMC_CAP2_NO_SDIO to tell the mmc core to
prevent them altogether.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200401145531.23247-1-ulf.hansson@linaro.org
Linus Torvalds [Sun, 24 May 2020 22:32:54 +0000 (15:32 -0700)]
Linux 5.7-rc7
Linus Torvalds [Sun, 24 May 2020 17:24:10 +0000 (10:24 -0700)]
Merge tag 'efi-urgent-2020-05-24' of git://git./linux/kernel/git/tip/tip
Pull EFI fixes from Thomas Gleixner:
"A set of EFI fixes:
- Don't return a garbage screen info when EFI framebuffer is not
available
- Make the early EFI console work properly with wider fonts instead
of drawing garbage
- Prevent a memory buffer leak in allocate_e820()
- Print the firmware error record properly so it can be decoded by
users
- Fix a symbol clash in the host tool build which only happens with
newer compilers.
- Add a missing check for the event log version of TPM which caused
boot failures on several Dell systems due to an attempt to decode
SHA-1 format with the crypto agile algorithm"
* tag 'efi-urgent-2020-05-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tpm: check event log version before reading final events
efi: Pull up arch-specific prototype efi_systab_show_arch()
x86/boot: Mark global variables as static
efi: cper: Add support for printing Firmware Error Record Reference
efi/libstub/x86: Avoid EFI map buffer alloc in allocate_e820()
efi/earlycon: Fix early printk for wider fonts
efi/libstub: Avoid returning uninitialized data from setup_graphics()
Linus Torvalds [Sun, 24 May 2020 17:21:02 +0000 (10:21 -0700)]
Merge tag 'x86-urgent-2020-05-24' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Two fixes for x86:
- Unbreak stack dumps for inactive tasks by interpreting the special
first frame left by __switch_to_asm() correctly.
The recent change not to skip the first frame so ORC and frame
unwinder behave in the same way caused all entries to be
unreliable, i.e. prepended with '?'.
- Use cpumask_available() instead of an implicit NULL check of a
cpumask_var_t in mmio trace to prevent a Clang build warning"
* tag 'x86-urgent-2020-05-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/unwind/orc: Fix unwind_get_return_address_ptr() for inactive tasks
x86/mmiotrace: Use cpumask_available() for cpumask_var_t variables
Linus Torvalds [Sun, 24 May 2020 17:14:58 +0000 (10:14 -0700)]
Merge tag 'sched-urgent-2020-05-24' of git://git./linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"A set of fixes for the scheduler:
- Fix handling of throttled parents in enqueue_task_fair() completely.
The recent fix overlooked a corner case where the first iteration
terminates due to an entity already being on the runqueue which
makes the list management incomplete and later triggers the
assertion which checks for completeness.
- Fix a similar problem in unthrottle_cfs_rq().
- Show the correct uclamp values in procfs which prints the effective
value twice instead of requested and effective"
* tag 'sched-urgent-2020-05-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix unthrottle_cfs_rq() for leaf_cfs_rq list
sched/debug: Fix requested task uclamp values shown in procfs
sched/fair: Fix enqueue_task_fair() warning some more
Linus Torvalds [Sun, 24 May 2020 00:16:18 +0000 (17:16 -0700)]
Merge git://git./linux/kernel/git/netdev/net
Pull networking fixes from David Miller:
1) Fix RCU warnings in ipv6 multicast router code, from Madhuparna
Bhowmik.
2) Nexthop attributes aren't being checked properly because of
mis-initialized iterator, from David Ahern.
3) Revert iop_idents_reserve() change as it caused performance
regressions and was just working around what is really a UBSAN bug
in the compiler. From Yuqi Jin.
4) Read MAC address properly from ROM in bmac driver (double iteration
proceeds past end of address array), from Jeremy Kerr.
5) Add Microsoft Surface device IDs to r8152, from Marc Payne.
6) Prevent reference to freed SKB in __netif_receive_skb_core(), from
Boris Sukholitko.
7) Fix ACK discard behavior in rxrpc, from David Howells.
8) Preserve flow hash across packet scrubbing in wireguard, from Jason
A. Donenfeld.
9) Cap option length properly for SO_BINDTODEVICE in AX25, from Eric
Dumazet.
10) Fix encryption error checking in kTLS code, from Vadim Fedorenko.
11) Missing BPF prog ref release in flow dissector, from Jakub Sitnicki.
12) dst_cache must be used with BH disabled in tipc, from Eric Dumazet.
13) Fix use after free in mlxsw driver, from Jiri Pirko.
14) Order kTLS key destruction properly in mlx5 driver, from Tariq
Toukan.
15) Check devm_platform_ioremap_resource() return value properly in
several drivers, from Tiezhu Yang.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (71 commits)
net: smsc911x: Fix runtime PM imbalance on error
net/mlx4_core: fix a memory leak bug.
net: ethernet: ti: cpsw: fix ASSERT_RTNL() warning during suspend
net: phy: mscc: fix initialization of the MACsec protocol mode
net: stmmac: don't attach interface until resume finishes
net: Fix return value about devm_platform_ioremap_resource()
net/mlx5: Fix error flow in case of function_setup failure
net/mlx5e: CT: Correctly get flow rule
net/mlx5e: Update netdev txq on completions during closure
net/mlx5: Annotate mutex destroy for root ns
net/mlx5: Don't maintain a case of del_sw_func being null
net/mlx5: Fix cleaning unmanaged flow tables
net/mlx5: Fix memory leak in mlx5_events_init
net/mlx5e: Fix inner tirs handling
net/mlx5e: kTLS, Destroy key object after destroying the TIS
net/mlx5e: Fix allowed tc redirect merged eswitch offload cases
net/mlx5: Avoid processing commands before cmdif is ready
net/mlx5: Fix a race when moving command interface to events mode
net/mlx5: Add command entry handling completion
rxrpc: Fix a memory leak in rxkad_verify_response()
...
Dinghao Liu [Sat, 23 May 2020 08:08:20 +0000 (16:08 +0800)]
net: smsc911x: Fix runtime PM imbalance on error
Remove runtime PM usage counter decrement when the
increment function has not been called to keep the
counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 23 May 2020 23:39:45 +0000 (16:39 -0700)]
Merge tag 'mlx5-fixes-2020-05-22' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2020-05-22
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v4.13
('net/mlx5: Add command entry handling completion')
For -stable v5.2
('net/mlx5: Fix error flow in case of function_setup failure')
('net/mlx5: Fix memory leak in mlx5_events_init')
For -stable v5.3
('net/mlx5e: Update netdev txq on completions during closure')
('net/mlx5e: kTLS, Destroy key object after destroying the TIS')
('net/mlx5e: Fix inner tirs handling')
For -stable v5.6
('net/mlx5: Fix cleaning unmanaged flow tables')
('net/mlx5: Fix a race when moving command interface to events mode')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Qiushi Wu [Fri, 22 May 2020 19:07:15 +0000 (14:07 -0500)]
net/mlx4_core: fix a memory leak bug.
In function mlx4_opreq_action(), pointer "mailbox" is not released,
when mlx4_cmd_box() return and error, causing a memory leak bug.
Fix this issue by going to "out" label, mlx4_free_cmd_mailbox() can
free this pointer.
Fixes:
fe6f700d6cbb ("net/mlx4_core: Respond to operation request by firmware")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko [Fri, 22 May 2020 17:09:28 +0000 (20:09 +0300)]
net: ethernet: ti: cpsw: fix ASSERT_RTNL() warning during suspend
vlan_for_each() are required to be called with rtnl_lock taken, otherwise
ASSERT_RTNL() warning will be triggered - which happens now during System
resume from suspend:
cpsw_suspend()
|- cpsw_ndo_stop()
|- __hw_addr_ref_unsync_dev()
|- cpsw_purge_all_mc()
|- vlan_for_each()
|- ASSERT_RTNL();
Hence, fix it by surrounding cpsw_ndo_stop() by rtnl_lock/unlock() calls.
Fixes:
15180eca569b ("net: ethernet: ti: cpsw: fix vlan mcast")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Fri, 22 May 2020 15:55:45 +0000 (17:55 +0200)]
net: phy: mscc: fix initialization of the MACsec protocol mode
At the very end of the MACsec block initialization in the MSCC PHY
driver, the MACsec "protocol mode" is set. This setting should be set
based on the PHY id within the package, as the bank used to access the
register used depends on this. This was not done correctly, and only the
first bank was used leading to the two upper PHYs being unstable when
using the VSC8584. This patch fixes it.
Fixes:
1bbe0ecc2a1a ("net: phy: mscc: macsec initialization")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leon Yu [Fri, 22 May 2020 15:29:43 +0000 (23:29 +0800)]
net: stmmac: don't attach interface until resume finishes
Commit
14b41a2959fb ("net: stmmac: Delete txtimer in suspend") was the
first attempt to fix a race between mod_timer() and setup_timer()
during stmmac_resume(). However the issue still exists as the commit
only addressed half of the issue.
Same race can still happen as stmmac_resume() re-attaches interface
way too early - even before hardware is fully initialized. Worse,
doing so allows network traffic to restart and stmmac_tx_timer_arm()
being called in the middle of stmmac_resume(), which re-init tx timers
in stmmac_init_coalesce(). timer_list will be corrupted and system
crashes as a result of race between mod_timer() and setup_timer().
systemd--1995 2.... 552950018us : stmmac_suspend: 4994
ksoftirq-9 0..s2 553123133us : stmmac_tx_timer_arm: 2276
systemd--1995 0.... 553127896us : stmmac_resume: 5101
systemd--320 7...2 553132752us : stmmac_tx_timer_arm: 2276
(sd-exec-1999 5...2 553135204us : stmmac_tx_timer_arm: 2276
---------------------------------
pc : run_timer_softirq+0x468/0x5e0
lr : run_timer_softirq+0x570/0x5e0
Call trace:
run_timer_softirq+0x468/0x5e0
__do_softirq+0x124/0x398
irq_exit+0xd8/0xe0
__handle_domain_irq+0x6c/0xc0
gic_handle_irq+0x60/0xb0
el1_irq+0xb8/0x180
arch_cpu_idle+0x38/0x230
default_idle_call+0x24/0x3c
do_idle+0x1e0/0x2b8
cpu_startup_entry+0x28/0x48
secondary_start_kernel+0x1b4/0x208
Fix this by deferring netif_device_attach() to the end of
stmmac_resume().
Signed-off-by: Leon Yu <leoyu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tiezhu Yang [Fri, 22 May 2020 11:03:21 +0000 (19:03 +0800)]
net: Fix return value about devm_platform_ioremap_resource()
When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Rapoport [Sat, 23 May 2020 19:57:18 +0000 (22:57 +0300)]
sparc32: fix page table traversal in srmmu_nocache_init()
The srmmu_nocache_init() uses __nocache_fix() macro to add an offset to
page table entry to access srmmu_nocache_pool.
But since sparc32 has only three actual page table levels, pgd, p4d and
pud are essentially the same thing and pgd_offset() and p4d_offset() are
no-ops, the __nocache_fix() should be done only at PUD level.
Remove __nocache_fix() for p4d_offset() and pud_offset() and keep it
only for PUD and lower levels.
Fixes:
c2bc26f7ca1f ("sparc32: use PUD rather than PGD to get PMD in srmmu_nocache_init()")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Anatoly Pugachev <matorola@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 23 May 2020 18:21:47 +0000 (11:21 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"11 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
MAINTAINERS: add files related to kdump
z3fold: fix use-after-free when freeing handles
sparc32: use PUD rather than PGD to get PMD in srmmu_nocache_init()
MAINTAINERS: update email address for Naoya Horiguchi
sh: include linux/time_types.h for sockios
kasan: disable branch tracing for core runtime
selftests/vm/write_to_hugetlbfs.c: fix unused variable warning
selftests/vm/.gitignore: add mremap_dontunmap
rapidio: fix an error in get_user_pages_fast() error handling
x86: bitops: fix build regression
device-dax: don't leak kernel memory to user space after unloading kmem
Linus Torvalds [Sat, 23 May 2020 18:06:13 +0000 (11:06 -0700)]
Merge tag 'driver-core-5.7-rc7' of git://git./linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"So, turns out the kobject fix didn't quite work, so here are four
patches that in the end, result in just two driver core fixes for
reported issues that no one has had problems with.
The kobject patch that was originally in here has now been reverted,
as Guenter reported boot problems with it on some of his systems"
* tag 'driver-core-5.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Revert "kobject: Make sure the parent does not get released before its children"
kobject: Make sure the parent does not get released before its children
driver core: Fix handling of SYNC_STATE_ONLY + STATELESS device links
driver core: Fix SYNC_STATE_ONLY device link implementation
Linus Torvalds [Sat, 23 May 2020 18:02:42 +0000 (11:02 -0700)]
Merge tag 'char-misc-5.7-rc7' of git://git./linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are some small char/misc driver fixes for 5.7-rc7 that resolve
some reported issues. Included in here are tiny fixes for the mei,
coresight, rtsx, ipack, and mhi drivers.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
misc: rtsx: Add short delay after exit from ASPM
bus: mhi: core: Fix some error return code
ipack: tpci200: fix error return code in tpci200_register()
coresight: cti: remove incorrect NULL return check
mei: release me_cl object reference
Linus Torvalds [Sat, 23 May 2020 17:57:55 +0000 (10:57 -0700)]
Merge tag 'staging-5.7-rc7' of git://git./linux/kernel/git/gregkh/staging
Pull staging/iio fixes from Greg KH:
"Here are some small staging and IIO driver fixes for 5.7-rc7
Nothing major, just a collection of IIO driver fixes for reported
issues, and a few small staging driver fixes that people have found.
Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: wfx: unlock on error path
staging: greybus: Fix uninitialized scalar variable
staging: kpc2000: fix error return code in kp2000_pcie_probe()
iio: sca3000: Remove an erroneous 'get_device()'
iio: adc: stm32-dfsdm: fix device used to request dma
iio: adc: stm32-adc: fix device used to request dma
iio: adc: ti-ads8344: Fix channel selection
staging: iio: ad2s1210: Fix SPI reading
iio: dac: vf610: Fix an error handling path in 'vf610_dac_probe()'
iio: imu: st_lsm6dsx: unlock on error in st_lsm6dsx_shub_write_raw()
iio: chemical: atlas-sensor: correct DO-SM channels
Linus Torvalds [Sat, 23 May 2020 17:50:38 +0000 (10:50 -0700)]
Merge tag 'tty-5.7-rc7' of git://git./linux/kernel/git/gregkh/tty
Pull tty/serial fix from Greg KH:
"Here is a single serial driver fix for 5.7-rc7. It resolves an issue
with the SiFive serial console init sequence that was reported a
number of times.
It has been in linux-next for a while now with no reported issues"
* tag 'tty-5.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: add missing spin_lock_init for SiFive serial console
Linus Torvalds [Sat, 23 May 2020 17:42:12 +0000 (10:42 -0700)]
Merge tag 's390-5.7-4' of git://git./linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Add missing R_390_JMP_SLOT relocation type in KASLR code.
- Fix set_huge_pte_at for empty ptes issue which has been uncovered
with arch page table helper tests.
- Correct initrd location for kdump kernel.
- Fix s390_mmio_read/write with MIO in PCI code.
* tag 's390-5.7-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/kaslr: add support for R_390_JMP_SLOT relocation type
s390/mm: fix set_huge_pte_at() for empty ptes
s390/kexec_file: fix initrd location for kdump kernel
s390/pci: Fix s390_mmio_read/write with MIO
Baoquan He [Sat, 23 May 2020 05:23:15 +0000 (22:23 -0700)]
MAINTAINERS: add files related to kdump
Kdump is implemented based on kexec, however some files are only related
to crash dumping and missing, add them to KDUMP entry.
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Dave Young <dyoung@redhat.com>
Link: http://lkml.kernel.org/r/20200520103633.GW5029@MiWiFi-R3L-srv
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Uladzislau Rezki [Sat, 23 May 2020 05:23:12 +0000 (22:23 -0700)]
z3fold: fix use-after-free when freeing handles
free_handle() for a foreign handle may race with inter-page compaction,
what can lead to memory corruption.
To avoid that, take write lock not read lock in free_handle to be
synchronized with __release_z3fold_page().
For example KASAN can detect it:
==================================================================
BUG: KASAN: use-after-free in LZ4_decompress_safe+0x2c4/0x3b8
Read of size 1 at addr
ffffffc976695ca3 by task GoogleApiHandle/4121
CPU: 0 PID: 4121 Comm: GoogleApiHandle Tainted: P S OE 4.19.81-perf+ #162
Hardware name: Sony Mobile Communications. PDX-203(KONA) (DT)
Call trace:
LZ4_decompress_safe+0x2c4/0x3b8
lz4_decompress_crypto+0x3c/0x70
crypto_decompress+0x58/0x70
zcomp_decompress+0xd4/0x120
...
Apart from that, initialize zhdr->mapped_count in init_z3fold_page() and
remove "newpage" variable because it is not used anywhere.
Signed-off-by: Uladzislau Rezki <uladzislau.rezki@sony.com>
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Qian Cai <cai@lca.pw>
Cc: Raymond Jennings <shentino@gmail.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200520082100.28876-1-vitaly.wool@konsulko.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>