Wenyou Yang [Thu, 14 Sep 2017 03:07:44 +0000 (11:07 +0800)]
configs: at91: Remove CONFIG_SYS_EXTRA_OPTIONS assignment
To remove the assignment of CONFIG_SYS_EXTRA_OPTIONS option,
which is deprecated, use the CONFIG_XXXX_BOOT options to
indicate the boot media, and the SoC is selected by the board.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Wenyou Yang [Thu, 14 Sep 2017 03:07:43 +0000 (11:07 +0800)]
ARM: at91: spl: Add macro CONFIG_XXXX_BOOT support
Use the CONFIG_XXXX_BOOT to indicate the boot media, instead of
the CONFIG_SYS_USE_XXXX option, which is declared by
CONFIG_SYS_EXTRA_OPTIONS option.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Wenyou Yang [Thu, 14 Sep 2017 03:07:42 +0000 (11:07 +0800)]
ARM: at91: Remove hardware.h included in configs
As said in READRE.kconfig, include/configs/*.h will be removed
after all options are switched to Kconfig. As the first step,
remove the follow line from include/configs/*.h.
#include <asm/hardware.h>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Wenyou Yang [Thu, 14 Sep 2017 03:07:41 +0000 (11:07 +0800)]
ARM: at91: Add the SoC options to Kconfig
To prepare to remove the SoCs options such as SAMA5D2, SAMA5D3
and SAMA5D4 from the CONFIG_SYS_EXTRA_OPTIONS option which is
deprecated, add the SoC options to Kconfig.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Wenyou Yang [Thu, 14 Sep 2017 03:07:40 +0000 (11:07 +0800)]
ARM: at91: Move CONFIG_AT91FAMILY option to Kconfig
Move the CONFIG_AT91FAMILY option from include/mach/<soc>.h header
file to Kconfig.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Wenyou Yang [Wed, 13 Sep 2017 06:58:54 +0000 (14:58 +0800)]
board: atmel: Add SAMA5D27 SOM1 EK board
The SAMA5D27-SiP (System in Package) integrates the SAMA5D2
with 1Gbit DDR2-SDRAM in a single package.
The SAMA5D27 SOM1 embeds a 64Mbit QSPI flash, KSZ8081 Phy and
Mac-address EEPROM.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Wed, 13 Sep 2017 06:58:53 +0000 (14:58 +0800)]
ARM: at91: Get the Chip ID of SAMA5D2 SiP
The SAMA5D2 SiP(System in Package) has different Chip IDs in the
CHIPID and CHIP_EXID registers.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Wed, 13 Sep 2017 06:58:52 +0000 (14:58 +0800)]
ARM: at91: mach: Add missing defines of MPDDRC
Add missing defines of Multiport DDR-SDRAM Controller (MPDDRC).
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Wed, 13 Sep 2017 06:58:51 +0000 (14:58 +0800)]
ARM: at91: spl: Add boot device for boot from QSPI
Add the boot device for booting from the QSPI flash.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Wed, 13 Sep 2017 06:58:50 +0000 (14:58 +0800)]
board: sama5d2_xplained: Make SPL work on spiflash
Because before switching to a lower clock source, we must switch
the clock source first instead of last. So before configuring the
PMC_MCKR register, invoke at91_mck_init_down() first.
As said in datasheet, the the size of SPL must not exceed the maximum
size allowed(64Kbytes).
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Wed, 13 Sep 2017 06:58:49 +0000 (14:58 +0800)]
ARM: at91: spl: Add mck function to lower rate while switching
Refer to the commit
70f8c8316ad(PMC: add new mck function to lower
rate while switching) from AT91Bootstrap.
While switching to a lower clock source, we must switch the clock
source first instead of last. Otherwise, we could end up with
too high frequency on internal bus and peripherals.
This happens on SAMA5D2 as exitting from the ROM code.
Add a function pmc_mck_init_down() to allow this sequence.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Wed, 13 Sep 2017 06:58:48 +0000 (14:58 +0800)]
ARM: at91: spl: Adjust switching to oscillator for SAMA5D2
As said in 29.5.7 section of SAMA5D2 datasheet, before switching to
the crystal oscillator, a check must be carried out to ensure that
the oscillator is present and that its freqency is valid.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Wed, 13 Sep 2017 06:58:47 +0000 (14:58 +0800)]
atmel: common: Add function to display via DM_VIDEO's API
Add a function to display the company's logo and board information
via the API from DM_VIDEO. This function can be shared by other
atmel boards, so locate it in board/atmel/common folder.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Wed, 13 Sep 2017 06:58:46 +0000 (14:58 +0800)]
lib: at91: Add logo files used via API of DM_VIDEO
In order to display the company's logo via the API of DM_VIDEO,
and add the logo files of both Atmel and Microchip.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Tue, 5 Sep 2017 10:30:08 +0000 (18:30 +0800)]
ARM: dts: at91: sama5: Add the sfr node
For sama5d2, add the sfr node with syscon support.
In order to access the SFR_UTMICKTRIM register for the utmi clock
driver, add the phandle property for the utmi node to point to the
sfr node.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Wenyou Yang [Tue, 5 Sep 2017 10:30:07 +0000 (18:30 +0800)]
clk: at91: utmi: Set the reference clock frequency
By default, it is assumed that the UTMI clock is generated from
a 12 MHz reference clock (MAINCK). If it's not the case, the FREQ
field of the SFR_UTMICKTRIM has to be updated to generate the UTMI
clock in the proper way.
The UTMI clock has a fixed rate of 480 MHz. In fact, there is no
multiplier we can configure. The multiplier is managed internally,
depending on the reference clock frequency, to achieve the target
of 480 MHz.
The patch is cloned from the patch of mailing-list:
[PATCH v2] clk: at91: utmi: set the mainck rate
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
[trini: Depend on SPL_DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
Wenyou Yang [Mon, 31 Jul 2017 07:21:57 +0000 (15:21 +0800)]
clk: Kconfig: Add dependences of SPL_CLK
The SPL_CLK config should depend on SPL && SPL_DM.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Thu, 14 Sep 2017 01:35:45 +0000 (21:35 -0400)]
Merge git://git.denx.de/u-boot-dm
Simon Glass [Wed, 13 Sep 2017 02:30:28 +0000 (20:30 -0600)]
patman: Fix error when the email blacklist is missing
This section of the settings file may be missing. Handle that gracefully
rather than emitting an error.
Also update patman to write this section when a new settings file is
created.
Fixes:
e11aa602 (patman: add support for omitting bouncing addresses)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chris Packham <judge.pckham@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Adam Ford [Tue, 12 Sep 2017 20:45:05 +0000 (15:45 -0500)]
ARM: davinci: Update da8xxevm Maintainers
The e-mail addresses for DA8XXEVM BOARD and DA850_AM18XXEVM BOARD
are invalid.
Remove DA8XXEVM.
Update DA850_AM18XXEVM to have me be the maintainer since I work
for Logic PD and have access to OMAP-L138 and AM1808 EVM kits.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adam Ford [Tue, 12 Sep 2017 20:27:33 +0000 (15:27 -0500)]
Convert CONFIG_EMIF4 et al to Kconfig
This converts the following to Kconfig:
CONFIG_EMIF4
CONFIG_SDRC
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Adam Ford [Fri, 8 Sep 2017 22:01:18 +0000 (17:01 -0500)]
Convert CONFIG_MAC_ADDR_IN_SPIFLASH et al to Kconfig
This converts the following to Kconfig:
CONFIG_MAC_ADDR_IN_SPIFLASH
CONFIG_MAC_ADDR_IN_EEPROM
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Fri, 8 Sep 2017 22:01:17 +0000 (17:01 -0500)]
davinci: da850evm: Make EEPROM MAC code configurable
There was a check for CONFIG_MAC_ADDR_IN_EEPROM and
a check for CONFIG_MAC_ADDR_IN_SPIFLASH, however
some of the EEPROM related code wasn't encapsulated
inside the #if defined statement so the EEPROM code
could get executed even when it wasn't explicitly
enabled or wanted.
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Tue, 5 Sep 2017 02:08:02 +0000 (21:08 -0500)]
include/configs: remove references to SMNAND_ENV_OFFSET
In mancy cases both CONFIG_ENV_OFFSET and CONFIG_ENV_ADDR point
to an otherwise-unused SMNAND_ENV_OFFSET.
This patch will set both CONFIG_ENV_OFFSET and CONFIG_ENV_ADDR to
whatever value was defined by SMNAND_ENV_OFFSET.
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Fri, 25 Aug 2017 12:33:26 +0000 (07:33 -0500)]
arm: dts: omap3: Re-sync DTS files with Linux 4.13-RC5
The DTS files had some spacing issues and they needed fixing. This
pull re-sync's the OMAP3xx related DTS files with Linux 4.13-RC5.
To keep the DTS and DTSI files clean and in sync with Linux, new
u-boot.dtsi files are added.
Signed-off-by: Adam Ford <aford173@gmail.com>
V3: The resync broke card detect on MMC1 on Logic PD's Torpedo,
so we add the cd-invert to the Torpedo's -u-boot.dtsi file.
V2: Add the u-boot.dtsi files for OMAP3, OMAP36xx, and Torpedo
Remove the need for the second patch in the series
Adam Ford [Sun, 13 Aug 2017 12:36:14 +0000 (07:36 -0500)]
omap3: omap3_logic: Finish enabling fastboot on MUSB
Either the USB and Fastboot were never finished, or somehow it got
lost. This puts enough hooks back into omap3logic to enable
fastboot and hopefully prepare it for Kconfig conversion.
Signed-off-by: Adam Ford <aford173@gmail.com>
Wenyou Yang [Tue, 8 Aug 2017 00:50:33 +0000 (08:50 +0800)]
ARM: dts: ethernut5: Fix the build warning
Fix the building warning as below:
---8<----
Warning (reg_format): "reg" property in /i2c-gpio-0/pcf8563@50 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /i2c-gpio-0/pcf8563@50
Warning (avoid_default_addr_size): Relying on default #size-cells value for /i2c-gpio-0/pcf8563@50
--->8----
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Keng Soon Cheah [Fri, 25 Aug 2017 03:29:07 +0000 (20:29 -0700)]
serial: nulldev: Add nulldev serial driver
Some device the serial console's initialization cannot run early during
the boot process. Hence, nulldev serial device is helpful on that
situation.
For example, if the serial module was implemented in FPGA. Serial
initialization is prohibited to run until the FPGA was programmed.
This commit is to adding nulldev serial driver. This will allows the
default console to be specified as a nulldev.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Keng Soon Cheah <keng.soon.cheah@ni.com>
Cc: Chen Yee Chew <chen.yee.chew@ni.com>
Anatolij Gustschin [Tue, 1 Aug 2017 14:17:12 +0000 (16:17 +0200)]
spl: add newline in debug output
With debug enabled, SPL output following these debug prints is on the
same line and it is hard to read. Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Vishal Mahaveer [Sat, 26 Aug 2017 21:51:22 +0000 (16:51 -0500)]
ARM: DRA72x: Add support for detection of DRA71x SR 2.1
DRA71x processors are reduced pin and software compatible
derivative of DRA72 processors. Add support for detection
of SR2.1 version of DRA71x family of processors.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Adam Ford [Fri, 25 Aug 2017 18:51:01 +0000 (13:51 -0500)]
davinci: da850-evm: switch to using TI_COMMON_CMD_OPTIONS
Like the OMAP-L138 LCDK before it, let's move the da850-evm and
the variations to TI_COMMON_CMD_OPTIONS to cut back one some of the
defconfig entries.
Signed-off-by: Adam Ford <aford173@gmail.com>
Masahiro Yamada [Fri, 25 Aug 2017 16:02:39 +0000 (01:02 +0900)]
linux/io.h: import generic ioread* / iowrite* accessors from Linux
Some drivers in Linux (ex. drivers/mtd/nand/denali.c) use
ioread*/iowrite* accessors. Import them to make drivers more
synced. I copied code from include/asm-generic/io.h of Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Fri, 25 Aug 2017 15:50:17 +0000 (00:50 +0900)]
dma: import linux/dma-direction.h to consolidate enum dma_data_direction
Import include/linux/dma-direction.h from Linux 4.13-rc7 and delete
duplicated definitions of enum dma_data_direction.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Adam Ford [Tue, 22 Aug 2017 15:50:02 +0000 (10:50 -0500)]
omap3: am3517_evm: Enable TI_COMMON_CMD_OPTION
Enable TI_COMMON_CMD_OPTIONS and remove similar options
from the defconfig. Updated with savedefconfig.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
Adam Ford [Tue, 22 Aug 2017 15:50:01 +0000 (10:50 -0500)]
ARM: OMAP3: am3517_evm: Move header to ti_omap3_common.h
Much of the AM3517 functions are copies of the standard definitions
used in ti_omap3_common.h. Moving to include a common file
reduces the amount of duplicative code and clutter. A few
AM3517 specific functions (like EMIF4) are explictly defined
and a few items are undefined or redefined, but overall the number
of lines of code shink.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
Andy Yan [Thu, 17 Aug 2017 07:55:50 +0000 (15:55 +0800)]
armv8: mmu: add space around operator
Add space around operator "+", make it
match the coding style.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Andy Yan [Thu, 17 Aug 2017 07:55:01 +0000 (15:55 +0800)]
armv8: mmu: remove unused macro definition
Macro VA_BITS and PTE_BLOCK_BITS are not used
in the code, so remove them.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Tomas Melin [Thu, 3 Aug 2017 06:16:54 +0000 (09:16 +0300)]
cosmetic: bootcount: correct comment for used scratch register
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Wenyou Yang [Mon, 31 Jul 2017 03:25:31 +0000 (11:25 +0800)]
misc: i2c_eeprom: Add compatible for AT24MAC402
Add the new compatible "atmel,24mac402" to accommodate AT24MAC402.
The AT24MAC402 is a 2K Serial EEPROM and the 2-Kbit memory array
is internally organized as 16 pages of 16 bytes of EEPROM each.
The 48-bit EUI address in the AT24MAC402 are located in the extended
memory block.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Wenyou Yang [Mon, 31 Jul 2017 03:25:30 +0000 (11:25 +0800)]
misc: i2c_eeprom: Add compatible for
24AA02E48
Add the new compatible "microchip,
24aa02e48" to accommodate
24AA02E48,
the
24AA02E48 is a 2K I2C Serial EEPROM with pre-programmed globally
unique, 48-bit node address, and 8-byte page size.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Andrew F. Davis [Mon, 31 Jul 2017 15:58:22 +0000 (10:58 -0500)]
configs: k2g_evm: Remove PMMC loading environment commands
The PMMC firmware should be bundled with the FIT image for HS devices,
remove the steps that load and install this firmware outside of FIT.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Andrew F. Davis [Mon, 31 Jul 2017 15:58:21 +0000 (10:58 -0500)]
ARM: k2g: Add FIT image handler for PMMC firmware
The PMMC firmware should be bundled into a FIT image on HS
devices to allow authentication/decryption, add a handler to
process this PMMC firmware.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Andrew F. Davis [Mon, 31 Jul 2017 15:58:20 +0000 (10:58 -0500)]
image: Add TI PMMC image type
Add a new image type representing TI Power Management
Micro-Controller (PMMC) Firmware image type.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Rob Clark [Sat, 9 Sep 2017 10:47:43 +0000 (06:47 -0400)]
examples: add fallback memcpy
Solves build issue:
Building current source for 134 boards (12 threads, 1 job per thread)
arm: + lsxhl
+examples/api/vsprintf.o: In function `string16':
+lib/vsprintf.c:278: undefined reference to `memcpy'
+examples/api/uuid.o: In function `uuid_bin_to_str':
+lib/uuid.c:197: undefined reference to `memcpy'
+lib/uuid.c:199: undefined reference to `memcpy'
+make[3]: *** [examples/api/demo] Error 1
+make[2]: *** [examples/api] Error 2
+make[1]: *** [examples] Error 2
+make: *** [sub-make] Error 2
133 0 1 /134 sheevaplug
Signed-off-by: Rob Clark <robdclark@gmail.com>
Rob Clark [Sat, 9 Sep 2017 10:47:42 +0000 (06:47 -0400)]
vsprintf.c: add GUID printing
This works (roughly) the same way as linux's, but we currently always
print lower-case (ie. we just keep %pUB and %pUL for compat with linux),
mostly just because that is what uuid_bin_to_str() supports.
%pUb:
01020304-0506-0708-090a-
0b0c0d0e0f10
%pUl:
04030201-0605-0807-090a-
0b0c0d0e0f10
It will be used by a later efi_loader paths for efi variables and for
device-path-to-text protocol, and also quite useful for debug prints
of protocol GUIDs.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rob Clark [Sat, 9 Sep 2017 10:47:41 +0000 (06:47 -0400)]
vsprintf.c: add UTF-16 string (%ls) support
This is convenient for efi_loader which deals a lot with UTF-16. Only
enabled with CC_SHORT_WCHAR, leaving room to add a UTF-32 version when
CC_SHORT_WCHAR is not enabled.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rob Clark [Sat, 9 Sep 2017 10:47:40 +0000 (06:47 -0400)]
lib: add some utf16 handling helpers
We'll eventually want these in a few places in efi_loader, and also
vsprintf.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Rob Clark [Sat, 9 Sep 2017 10:47:39 +0000 (06:47 -0400)]
kbuild: Enable -fshort-wchar
EFI_LOADER really wants UTF-16 strings (ie. %ls and L"string" are 16bit
chars instead of 32bit chars). But rather than enabling -fshort-wchar
conditionally if EFI_LOADER is enabled, it was deemed preferrable to
globally switch.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tom Rini [Tue, 12 Sep 2017 16:02:50 +0000 (12:02 -0400)]
Merge git://git.denx.de/u-boot-fsl-qoriq
Tom Rini [Tue, 12 Sep 2017 15:00:53 +0000 (11:00 -0400)]
Travis-CI: Update PATH
We now can no longer re-use the provided path and need to give the
full PATH we want used now.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 12 Sep 2017 13:32:51 +0000 (09:32 -0400)]
Merge git://git.denx.de/u-boot-dm
Patrice Chotard [Mon, 4 Sep 2017 12:55:57 +0000 (14:55 +0200)]
dm: test: replace dm_scan_dt() by of dm_extended_scan_fdt() in dm_do_test
This allows to scan the DT including all "clocks" node's sub-nodes
in which fixed-clock are defined.
All fixed-clock should be defined inside a clocks node which collect all
external oscillators. Until now, all clocks sub-nodes can't be binded except
if the "simple-bus" compatible string is added which is a hack.
Update test.dts by moving clk_fixed node inside clocks.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Patrice Chotard [Mon, 4 Sep 2017 12:55:56 +0000 (14:55 +0200)]
dm: core: add clocks node scan
Currently, all fixed-clock declared in "clocks" node in device tree
can be binded by clk_fixed_rate.c driver only if each of them have
the "simple-bus" compatible string.
This constraint has been invoked here [1].
This patch offers a solution to avoid adding "simple-bus" compatible
string to nodes that are not busses.
[1] https://patchwork.ozlabs.org/patch/558837/
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Chris Packham [Fri, 1 Sep 2017 08:57:53 +0000 (20:57 +1200)]
patman: add support for omitting bouncing addresses
Add support for reading a list of bouncing addresses from a in-tree file
(doc/bounces) and from the ~/.patman config file. These addresses are
stripped from the Cc list.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com <mailto:philipp.tomsich@theobroma-systems.com>>
Simon Glass [Sun, 13 Aug 2017 22:02:54 +0000 (16:02 -0600)]
moveconfig: Use fd.write() instead of print >>
Adjust this code so that it can work with Python 2 and 3.
Fixes: d73fcb1 (moveconfig: Support building a simple config database)
Reported-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 5 Aug 2017 21:45:54 +0000 (15:45 -0600)]
dm: core: Add ofnode_for_each_subnode()
Add a convenience macro to iterate over subnodes of a node. Make use of
this where appropriate in the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 4 Aug 2017 09:30:30 +0000 (03:30 -0600)]
genconfig.py: Print defconfig next to warnings
At present we sometimes see warnings of the form:
/tmp/tmpMA89kB:36: warning: overriding the value of CMD_SPL.
Old value: "y", new value: "y".
This is not very useful as it does not show whch defconfig file it relates
to. Update the tool to show this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 2 Aug 2017 18:12:02 +0000 (12:12 -0600)]
dm: core: Show driver name with 'dm tree'
It is often useful to see which driver was actually selected for each
device. Add a new 'Driver' column to provide this information. Sample
output:
Class Probed Driver Name
----------------------------------------
root [ + ] root_drive root_driver
keyboard [ + ] i8042_kbd |-- keyboard
serial [ + ] ns16550_se |-- serial
rtc [ ] rtc_mc1468 |-- rtc
timer [ + ] tsc_timer |-- tsc-timer
syscon [ + ] ich6_pinct |-- pch_pinctrl
pci [ + ] pci_x86 |-- pci
northbridge [ + ] bd82x6x_no | |-- northbridge@0,0
video [ + ] bd82x6x_vi | |-- gma@2,0
vidconsole0 [ + ] vidconsole | | `-- gma@2,0.vidconsole0
...
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Wed, 2 Aug 2017 18:12:01 +0000 (12:12 -0600)]
dm: core: Drop use of strlcpy()
We can use printf() to limit the string width. Adjust the code to do this
instead of using strlcpy() which is a bit clumbsy.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng [Tue, 1 Aug 2017 23:33:34 +0000 (16:33 -0700)]
sandbox: Convert SANDBOX_BITS_PER_LONG to Kconfig
Convert SANDBOX_BITS_PER_LONG to Kconfig and assign it a correct
number depending on which host we are going to build and run.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Tue, 1 Aug 2017 23:33:33 +0000 (16:33 -0700)]
sandbox: Introduce Kconfig option for 32/64 bit host
It seems most of the time we are building and running sandbox on 64-bit host.
But we do support 32-bit host as well. Introduce Kconfig option for this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Jean-Jacques Hiblot [Fri, 9 Jun 2017 14:45:18 +0000 (16:45 +0200)]
blk: dm: make blk_create_device() take a number of block instead of a size
There is an overflow problem when taking the size instead of the number
of blocks in blk_create_device(). This results in a wrong device size: the
device apparent size is its real size modulo 4GB.
Using the number of blocks instead of the device size fixes the problem and
is more coherent with the internals of the block layer.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Wed, 6 Sep 2017 05:08:14 +0000 (13:08 +0800)]
misc: Kconfig: Add SPL_I2C_EEPROM option
This option is an SPL-variant of the I2C_EEPROM option to enable
the driver for generic I2C-attached EEPROMs for SPL.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Fri, 1 Sep 2017 08:26:18 +0000 (16:26 +0800)]
board: sama5d4_xplained: Set mac address from eeprom
Add the code to set the ethernet mac address from eeprom by using
the common code from the common folder.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Fri, 1 Sep 2017 08:26:17 +0000 (16:26 +0800)]
board: sama5d2_xplained: Replace code to set mac address
Replace the code to set the ethernet mac address with the code from
the common folder.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Fri, 1 Sep 2017 08:26:16 +0000 (16:26 +0800)]
board: atmel: Create board/$(VENDOR)/common folder
Create board/$(VENDOR)/common folder to accommodate the common code
shared by other atmel boards, now put the code to set ethernet mac
address from eeprom, which uses the i2c eeprom driver.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Lokesh Vutla [Wed, 23 Aug 2017 06:09:07 +0000 (11:39 +0530)]
env: ti: boot: Select dtb name for X15 revC
Select dtb name for am57xx BeagleBoard-X15 revC
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla [Wed, 23 Aug 2017 06:09:06 +0000 (11:39 +0530)]
board: ti: am57xx: Add dt support for BeagleBoard-X15 revC
Add support for selecting proper dtb for
am57xx BeagleBoard X15 revC u-boot from FIT
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Steve Kipisz [Tue, 22 Aug 2017 08:22:58 +0000 (13:52 +0530)]
board: ti: am571x: Add 666MHz support for AM571x IDK
AM571x supports DDR running at 666MHz. Right now it is
clocked at 532MHz which is lower than what is supported.
In order to have maximum performance on AM571-IDK,
switch DDR to 666MHz.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla [Mon, 21 Aug 2017 07:21:01 +0000 (12:51 +0530)]
board: ti: dra76: Add dt support
Add support for selecting proper dtb for
dra76x u-boot from FIT.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla [Mon, 21 Aug 2017 07:21:00 +0000 (12:51 +0530)]
arm: dts: Add u-boot specific compatibles
Separate out u-boot specific compatibles from dts files.
This will help in syncing dts files in future.
Also these will get deleted eventually once respective drivers
are capable of handling Linux dts files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla [Mon, 21 Aug 2017 07:20:59 +0000 (12:50 +0530)]
arm: dts: dra7: sync DT with latest Linux
Sync all dra7* specific dts files with the upstream
kernel including changes queued for 4.14
https://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap.git/log/?h=omap-for-v4.14/dt-v3
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla [Mon, 21 Aug 2017 07:20:58 +0000 (12:50 +0530)]
env: ti: boot: Select dtb name for dra76
Select dtb name for dra76-evm.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 21 Aug 2017 07:20:57 +0000 (12:50 +0530)]
board: ti: dra76-evm: Add support for powering on mmc ldo
ldo4 is used to poweron mmc on dra76-evm. Enable it.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 21 Aug 2017 07:20:56 +0000 (12:50 +0530)]
board: ti: dra76-evm: Add the pinmux data
Adding pinmux and IODELAY data for dra76-evm.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 21 Aug 2017 07:20:55 +0000 (12:50 +0530)]
board: ti: dra76-evm: Add DDR data
dra76-evm has the ddr parts connectedi running at 666MHz:
EMIF1: MT41K512M16HA-125 AIT:A x 2
EMIF2: MT41K512M8RH-125-AAT:E x 4
Add support for configuring the above DDR parts.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Keerthy [Mon, 21 Aug 2017 07:20:54 +0000 (12:50 +0530)]
board: ti: dra76-evm: Add the pmic data
dra76-evm uses lp8736 and tps65917 pmic for powering on
various peripherals. Add data for these pmics and register
for dra76-evm.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 21 Aug 2017 07:20:53 +0000 (12:50 +0530)]
board: ti: dra76-evm: Add epprom support
The dra76-evm is a board based on TI's DRA76 processor
Add eeprom support
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Praneeth Bajjuri [Mon, 21 Aug 2017 07:20:52 +0000 (12:50 +0530)]
arm: dra76: Add support for ES1.0 detection
dra76 family is a high-performance, infotainment application
device, based on OMAP architecture on a 28-nm technology.
This contains most of the subsystems, peripherals that are
available on dra74, dra72 family. This SoC mainly features
Subsystems:
- 2 x Cortex-A15 with max speed of 1.8GHz
- 2 X DSP
- 2 X Cortex-M4 IPU
- ISS
- CAL
- DSS
- VPE
- VIP
Connectivity peripherals:
- 1 USB3.0 and 3 USB2.0 subsystems
- 1 x SATA
- 2 x PCI Express Gen2
- 3-port Gigabit ethernet switch
- 2 x CAN
- MCAN
Adding CPU detection support for the dra76 ES1.0 soc
and update prcm, control module, dplls data.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 21 Aug 2017 07:20:51 +0000 (12:50 +0530)]
arm: dra7: Kconfig: Select LP87565 related configs
LP87565 is present on dra76-evm. Select it for
TARGET_DRA7XX_EVM.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla [Mon, 21 Aug 2017 07:20:50 +0000 (12:50 +0530)]
palmas: Add support for powering different ldos
It is not necessary that ldo1 is used to power on mmc.
So, add support for passing ldo registers for powering on mmc.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 21 Aug 2017 07:20:49 +0000 (12:50 +0530)]
arm: omap5+: Add board specific ldo powering
It is not necessary all omap5+ based uses the same PMIC
to poweron mmc. So add support for enabling mmc based on board.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tom Rini [Mon, 11 Sep 2017 19:54:39 +0000 (15:54 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-video
Tom Rini [Mon, 11 Sep 2017 18:10:40 +0000 (14:10 -0400)]
Prepare v2017.09
Signed-off-by: Tom Rini <trini@konsulko.com>
Jorge Ramirez-Ortiz [Mon, 11 Sep 2017 14:07:02 +0000 (16:07 +0200)]
MAINTAINERS: board: qcom: db410c: Maintainer changed
Replacing original author Mateusz Kulikowski
<mateusz.kulikowski@gmail.com> as db410c maintainer
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
York Sun [Fri, 8 Sep 2017 16:33:49 +0000 (09:33 -0700)]
armv8: fsl-layerscape: Add back L3 flushing for all exception levels
CCN-504 HPF registers were believed to be accessible only from EL3.
However, recent tests proved otherwise. Remove checking for exception
level to re-enable L3 cache flushing for all levels.
Signed-off-by: York Sun <york.sun@nxp.com>
Tested-by: Zhao Qiang <qiang.zhao@nxp.com>
Hou Zhiqiang [Mon, 4 Sep 2017 02:47:54 +0000 (10:47 +0800)]
armv8: ls1088a: Enable PCIe in defconfigs
Enabled PCIe support and PCI command feature.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Hou Zhiqiang [Mon, 4 Sep 2017 02:47:53 +0000 (10:47 +0800)]
armv8: ls1088a: add PCIe dts node
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Hou Zhiqiang [Mon, 4 Sep 2017 02:47:52 +0000 (10:47 +0800)]
armv8: ls1088a: fix the MMU table for pcie config space
The pcie config space of ls1088a is different from ls2080a.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
York Sun [Thu, 7 Sep 2017 17:12:32 +0000 (10:12 -0700)]
armv8: fsl-layerscape: Fix MC reserved memory calculation
In case high region memory doesn't have enough space for Management
Complex (MC), the return value should indicate a failure so the
caller can handle it accordingly.
Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Ebony Zhu <ebony.zhu@nxp.com>
Ran Wang [Mon, 4 Sep 2017 10:46:55 +0000 (18:46 +0800)]
armv7: Add workaround for USB erratum A-009007
Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values
Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Ran Wang [Mon, 4 Sep 2017 10:46:54 +0000 (18:46 +0800)]
armv7: Add workaround for USB erratum A-008997
Low Frequency Periodic Singaling (LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter settings
Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Ran Wang [Mon, 4 Sep 2017 10:46:53 +0000 (18:46 +0800)]
armv7: Add workaround for USB erratum A-009798
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receive
Compliance test failure for a 100mV threshold.
Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Ran Wang [Mon, 4 Sep 2017 10:46:52 +0000 (18:46 +0800)]
armv7: Add workaround for USB erratum A-009008
USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature
Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Ran Wang [Mon, 4 Sep 2017 10:46:51 +0000 (18:46 +0800)]
armv8: Add workaround for USB erratum A-009007
Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values.
Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Ran Wang [Mon, 4 Sep 2017 10:46:50 +0000 (18:46 +0800)]
armv8: Add workaround for USB erratum A-008997
Low Frequency Periodic Signaling(LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter
settings
Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Ran Wang [Mon, 4 Sep 2017 10:46:49 +0000 (18:46 +0800)]
armv8: Add workaround for USB erratum A-009798
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receiver
Compliance test failure for a 100mV threshold.
Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Ran Wang [Mon, 4 Sep 2017 10:46:48 +0000 (18:46 +0800)]
armv8: Add workaround for USB erratum A-009008
USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature
Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Ran Wang [Mon, 4 Sep 2017 10:46:47 +0000 (18:46 +0800)]
armv8: Add scfg_clrsetbits_32(), scfg_clrbits_32()
Some erratum patch might need it to program registers.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Prabhakar Kushwaha [Thu, 31 Aug 2017 11:07:32 +0000 (16:37 +0530)]
armv8: ls1088aqds: Add support of EC1 and EC2
EC1 and EC2 are RGMII interface on ls1088aqds platform.
This patch add support of RGMII with PHY and MDIO
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>