Tom Rini [Fri, 4 Oct 2013 14:51:40 +0000 (10:51 -0400)]
TI:armv7: Change CONFIG_SYS_SPL_ARGS_ADDR to a higher address
With changes to increase the size of the device tree (required to move
more data out of the kernel and into DT), loading the args at the old
address leads to us overwriting things later on. To correct this, load
the args file to where we load the device tree anyhow. This is also
safe for non-DT booting as in either case we use r2 to pass in the
location of things.
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Tue, 1 Oct 2013 16:32:04 +0000 (12:32 -0400)]
am335x: Enable CONFIG_OMAP_WATCHDOG support
There is a board-specific portion for calling watchdog enable itself, in
main U-Boot.
Signed-off-by: Tom Rini <trini@ti.com>
Igor Grinberg [Mon, 16 Sep 2013 18:49:59 +0000 (21:49 +0300)]
cm-t35: move the display code to common place
Compulab OMAP3 boards use the same display initialization code.
Move the display initialization code to live under board/compulab/common
directory.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Igor Grinberg [Mon, 16 Sep 2013 18:49:58 +0000 (21:49 +0300)]
cm-t35: move the eeprom code to common place
Compulab boards use the same eeprom code, so move the eeprom related
code to live under board/compulab/common directory.
Also make several adjustments to eeprom functions namespace, so it will
be generic for compulab boards.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Andreas Bießmann [Fri, 6 Sep 2013 13:04:58 +0000 (15:04 +0200)]
tricorder: support 256MiB SDRAM on revision > D
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Andreas Bießmann [Fri, 6 Sep 2013 13:04:57 +0000 (15:04 +0200)]
tricorder: read kernel directly from NAND
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Thomas Weber [Fri, 6 Sep 2013 13:04:56 +0000 (15:04 +0200)]
tricorder: switch to alternative memtest
Increase the tested memory region for mtest and define
CONFIG_SYS_MEMTEST_SCRATCH for CONFIG_SYS_ALT_MEMTEST
Signed-off-by: Thomas Weber <thomas.weber@corscience.de>
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Thomas Weber [Fri, 6 Sep 2013 13:04:55 +0000 (15:04 +0200)]
tricorder: Make u-boot faster
Silent u-boot and no bootdelay
Signed-off-by: Thomas Weber <thomas.weber@corscience.de>
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Andreas Bießmann [Fri, 6 Sep 2013 13:04:54 +0000 (15:04 +0200)]
tricorder: add led support
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Andreas Bießmann [Fri, 6 Sep 2013 13:04:53 +0000 (15:04 +0200)]
tricorder: panic() on unknown board
Also hang() the board on panic().
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Andreas Bießmann [Fri, 6 Sep 2013 13:04:52 +0000 (15:04 +0200)]
tricorder: add tricordereeprom command
The new tricordereeprom command can read and write the eeprom for hardware
detection on tricorder devices.
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Andreas Bießmann [Fri, 6 Sep 2013 13:04:51 +0000 (15:04 +0200)]
tricorder: add mtdparts to environment
Before we always ran 'mtdparts default' which also set the mtdparts and mtdids
environment. But if we changed that values by intention we will overwrite
them with our default values. This is obviously bad!
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Andreas Bießmann [Fri, 6 Sep 2013 13:04:50 +0000 (15:04 +0200)]
tricorder: add cmdline history
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Andreas Bießmann [Fri, 6 Sep 2013 13:04:49 +0000 (15:04 +0200)]
tricorder: add configuration for a flashcard u-boot
The 'flashcard' u-boot configuration has a readonly environment and boots a
bare kernel/initrd to program the device from an clean environment.
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Andreas Bießmann [Fri, 6 Sep 2013 13:04:48 +0000 (15:04 +0200)]
tricorder: use generic provided loadaddr
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Andreas Bießmann [Fri, 6 Sep 2013 13:04:47 +0000 (15:04 +0200)]
tricorder: update flash partitioning
The new flash layout respects posible bad blocks in sectors reserved for e.g.
SPL, u-boot, kernel, env a.s.o.
Additionally this patch prepares for U-Boot Falcon mode for boot time saving.
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Thomas Weber [Fri, 6 Sep 2013 13:04:46 +0000 (15:04 +0200)]
tricorder: remove lcdmode from bootargs
Signed-off-by: Thomas Weber <thomas.weber@corscience.de>
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Heiko Schocher [Fri, 6 Sep 2013 03:21:24 +0000 (05:21 +0200)]
arm, da85x: update for the ipam390 board
- switch to correct ecc layout used by the RBL
enable CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
- update default environment
- change A2CR to correct value for UART boot mode
- adapt cs3cfg timings for nand
- change LED bootmode signalization
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Heiko Schocher [Fri, 6 Sep 2013 03:21:23 +0000 (05:21 +0200)]
nand, davinci: add special UBL ecc position
enable the RBL/UBL ECC layout through
CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC define
see for more info:
http://processors.wiki.ti.com/index.php/DM365_Nand_ECC_layout
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
Lokesh Vutla [Tue, 3 Sep 2013 14:17:18 +0000 (19:47 +0530)]
ARM: OMAP4: Convert to ti_armv7_common.h
Update omap4_common.h to use ti_armv7_common.h
Testing:
* Boot tested on OMAP4430 ES2.1 OMAP4460 ES1.1 SDP, OMAP4 PANDA/PANDA ES
* Verified ./MAKEALL -s omap
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Javier Martinez Canillas [Mon, 2 Sep 2013 08:04:02 +0000 (10:04 +0200)]
OMAP3: igep00x0: rename config file to omap3_igep00x0.h
There seems to be a naming convention for the configuration
files for boards using the same SoC family. This makes
easier to do changes that affect different boards based
on the same SoC.
Since the IGEPv2 board and the IGEP COM Module use a TI
OMAP35xx/DM37xx processor, is better to rename its board
config to use this naming scheme.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Javier Martinez Canillas [Mon, 2 Sep 2013 08:04:01 +0000 (10:04 +0200)]
ARM: IGEP0033: rename config file to am335x_igep0033.h
There seems to be a naming convention for the configuration
files for boards using the same SoC family. This makes
easier to do changes that affect different boards based
on the same SoC.
Since the IGEP COM AQUILA use a TI AM335x processor is better
to rename its board config to use this naming scheme.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Tom Rini [Wed, 28 Aug 2013 13:00:30 +0000 (09:00 -0400)]
TI:am33xx: Add bootcount support to ti_am335x_common.h
Enable the bootcount driver for am335x in general. We leave adding a
bootlimit and altbootcmd to the environment to the board ports.
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Wed, 28 Aug 2013 13:00:29 +0000 (09:00 -0400)]
bootcount_davinci: Switch to scratch register #2
The RTC IP block here provides 3 scratch registers. Currently when
using DeepSleep on am335x the scratch0/1 registers are used so moving
ourself to scratch2 makes cooperation easier.
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Wed, 28 Aug 2013 13:00:28 +0000 (09:00 -0400)]
am33xx, davinci: Create and use <asm/davinci_rtc.h>
Create a common header file for the RTC IP block that is shared between
davinci and am33xx.
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Wed, 28 Aug 2013 13:00:27 +0000 (09:00 -0400)]
drivers/rtc/davinci.c: Reference DAVINCI_RTC_BASE more directly
We shouldn't rely on a define to hide this cast for us.
Signed-off-by: Tom Rini <trini@ti.com>
Stefan Roese [Tue, 24 Sep 2013 06:22:19 +0000 (08:22 +0200)]
arm: Remove IXP425 boards pdnb3 and scpu
Remove Prodrive pdnb3 board (including the scpu variant) support
from mainline. As its unmaintained and not needed any more for
quite some time.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Martijn de Gouw <martijn.de.gouw@prodrive.nl>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Michal Simek [Thu, 22 Aug 2013 12:52:02 +0000 (14:52 +0200)]
zynq: Use arch_cpu_init() instead of lowlevel_init()
Zynq lowlevel_init() was implemented in C but stack
pointer is setup after function call in _main().
Move architecture setup to arch_cpu_init() which is call
as the first function in board_init_f() which
already have correct stack pointer.
Reported-by: Sven Schwermer <sven.schwermer@tuhh.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tom Rini [Wed, 16 Oct 2013 17:08:12 +0000 (13:08 -0400)]
Prepare v2013.10
Signed-off-by: Tom Rini <trini@ti.com>
Michal Simek [Wed, 16 Oct 2013 07:06:32 +0000 (09:06 +0200)]
microblaze: Fix watchdog initialization
The patch:
"blackfin: Move blackfin watchdog driver out of the blackfin arch folder."
(sha1:
e9a389a18477c1c57a0b30e9ea8f4d38c6e26e63)
changed hw_watchdog_init() prototype which didn't match
with Microblaze one.
This patch fixes the driver and Microblaze initialization.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 16 Oct 2013 07:06:31 +0000 (09:06 +0200)]
common: fsl: Fix broken SPDX-License-Identifier change
This bug was introduced by:
"Add GPL-2.0+ SPDX-License-Identifier to source files"
(sha1:
1a4596601fd395f3afb8f82f3f840c5e00bdd57a)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Scott Wood [Tue, 15 Oct 2013 22:41:27 +0000 (17:41 -0500)]
mtd: fix warnings due to 64-bit partition support
commit
39ac34473f3c96e77cbe03a49141771ed1639486 ("cmd_mtdparts: use 64
bits for flash size, partition size & offset") introduced warnings
in a couple places due to printf formats or pointer casting.
This patch fixes the warnings pointed out here:
http://lists.denx.de/pipermail/u-boot/2013-October/164981.html
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Tom Rini <trini@ti.com>
Timo Herbrecher [Tue, 15 Oct 2013 18:35:09 +0000 (00:05 +0530)]
spi: mxc_spi: Fix double incrementing read pointer for unaligned buffers
If dout buffer is not 32 bit-aligned or data to transmit is not multiple
of 32 bit the read data pointer is already incremented on single byte reads.
Signed-off-by: Timo Herbrecher <t.herbrecher@gateware.de>
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Bo Shen [Thu, 10 Oct 2013 05:07:37 +0000 (13:07 +0800)]
sf: probe: Add missing Atmel at25df321 flash
As the spi flash transfer to multiple parts, it is forgot to add
Atmel AT25DF321 spi flash support, which broken several Atmel EK
boards which this chip. So, add it
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Jagannadha Sutradharudu Teki [Mon, 14 Oct 2013 08:01:24 +0000 (13:31 +0530)]
spi: Add GPL-2.0+ SPDX-License-Identifier for missing files
Added GPL-2.0+ SPDX-License-Identifier for missed spi
source files.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Jagannadha Sutradharudu Teki [Thu, 10 Oct 2013 17:02:55 +0000 (22:32 +0530)]
sf: Add GPL-2.0+ SPDX-License-Identifier for missing ones
Added GPL-2.0+ SPDX-License-Identifier for missed sf
source files.
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Jagannadha Sutradharudu Teki [Thu, 10 Oct 2013 16:44:09 +0000 (22:14 +0530)]
sf: Minor cleanups.
- Add comments.
- Renamed few macros.
- Add tabs.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Jagannadha Sutradharudu Teki [Tue, 8 Oct 2013 17:56:47 +0000 (23:26 +0530)]
sf_ops: Unify bank_sel calculation code
Unified the bank_sel calculation code for erase and
write ops.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Jagannadha Sutradharudu Teki [Sat, 28 Sep 2013 17:38:14 +0000 (23:08 +0530)]
buildman: Use env to pick the python from $PATH
python used in buildman doesn't need to be placed in
/usr/bin/python, So use env to ensure that the interpreter
will pick the python from environment.
Usefull with several versions of python's installed on system.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tom Rini [Tue, 15 Oct 2013 00:19:56 +0000 (20:19 -0400)]
Merge branch 'buildman' of git://git.denx.de/u-boot-x86
Tom Rini [Thu, 10 Oct 2013 14:46:22 +0000 (10:46 -0400)]
cmd_sandbox.c: Update for do_(load|save) not taking a number base
Signed-off-by: Tom Rini <trini@ti.com>
Steven Falco [Mon, 7 Oct 2013 13:51:48 +0000 (09:51 -0400)]
Prevent null pointer dereference originating in cmd_pxe.c
Pass a valid cmdtp into do_tftpb(), do_ext2load(), and do_get_fat(), to
avoid possible crashes due to null pointer dereferencing.
Commit
d7884e047d08447dfd1374e9fa2fdf7ab36e56f5 does not go far enough.
There is still at least one call chain that can result in a crash.
The do_tftpb(), do_ext2load(), and do_get_fat() functions expect a valid
cmdtp. Passing in NULL is particularly bad in the do_tftpb() case,
because eventually boot_get_kernel() will be called with a NULL cmdtp:
do_tftpb() -> netboot_common() -> bootm_maybe_autostart() -> do_bootm()
-> do_bootm_states() -> bootm_find_os() -> boot_get_kernel()
Around line 991 in cmd_bootm.c, boot_get_kernel() will dereference the
null pointer, and the board will crash.
Signed-off-by: Steven A. Falco <stevenfalco@gmail.com>
Wolfgang Denk [Fri, 4 Oct 2013 15:43:26 +0000 (17:43 +0200)]
Coding Style cleanup: drop some excessive empty lines
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Oct 2013 15:43:25 +0000 (17:43 +0200)]
Coding Style cleanup: remove trailing empty lines
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Oct 2013 15:43:24 +0000 (17:43 +0200)]
Coding Style cleanup: replace leading SPACEs by TABs
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Drop changes for PEP 4 following python tools]
Signed-off-by: Tom Rini <trini@ti.com>
Wolfgang Denk [Mon, 7 Oct 2013 11:07:26 +0000 (13:07 +0200)]
Coding Style cleanup: remove trailing white space
Signed-off-by: Wolfgang Denk <wd@denx.de>
Dan Murphy [Thu, 10 Oct 2013 13:54:23 +0000 (08:54 -0500)]
ARM: omap4-panda: Add MAC address creation for panda
Add a MAC address create based on the OMAP die ID registers.
Then poplulate the ethaddr enviroment variable so that the device
tree alias can be updated prior to boot.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Jaehoon Chung [Mon, 30 Sep 2013 05:23:37 +0000 (14:23 +0900)]
pmic: max77686: fix the wrong offset
0x1D is reserved. So BUCK3DVS1 is started from 0x1e.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Markus Niebel [Fri, 4 Oct 2013 13:48:03 +0000 (15:48 +0200)]
env_mmc: fix buffer allocation for armv7
commit
d196bd880347373237d73e0d115b4d51c68cf2ad adds
redundand environment to mmc. The usage of malloc in
env_relocate_spec triggers cache errors on armv7.
Tested on a not mainlined i.MX53 board:
Board: TQMa53
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
ERROR: v7_dcache_inval_range - start address is not aligned - 0x8f57c2d8
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x8f57e2d8
ERROR: v7_dcache_inval_range - start address is not aligned - 0x8f57e2e0
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x8f5802e0
Using default environment
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Bo Shen [Tue, 8 Oct 2013 08:30:21 +0000 (16:30 +0800)]
env: dataflash: fix env_init issue
As the SPI controller is not initialized before env_init(), it causes
reading env in dataflash failed. So, although saveenv() successfully,
it shows warning information when reboot the system as following:
*** Warning - bad CRC, using default environment
Let the env_relocate() to check env CRC and import it.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Dan Murphy [Wed, 9 Oct 2013 18:53:58 +0000 (13:53 -0500)]
ARM: omap4: Update sdram setting for panda rev A6
OMAP4 panda rev A6 is a 4430 es2.3 IC with an updated memory
part.
The panda rev A6 uses Elpida 2x4Gb memory and no longer uses Micron
so the timings needs to be updated
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tom Rini [Thu, 10 Oct 2013 14:25:18 +0000 (10:25 -0400)]
am335x_evm.h: Make 'am335x_boneblack' use redundant environment
Signed-off-by: Tom Rini <trini@ti.com>
Daniel Schwierzeck [Sun, 13 Oct 2013 15:08:02 +0000 (17:08 +0200)]
.gitignore: add auto-generated /include/[s|t]pl-autoconf.mk
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Wolfgang Denk [Tue, 8 Oct 2013 19:53:45 +0000 (21:53 +0200)]
SPDX: document dual license notation
In [1] we discussed how we should deal with dual (or, more generally,
multiple) licensed files. Add this to Licenses/README so it's
properly documented.
[1] http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/166518
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Add the word 'list' to the end of the line, per Stephen Warren's
feedback]
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Mon, 14 Oct 2013 15:20:32 +0000 (11:20 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Tom Rini [Mon, 14 Oct 2013 13:37:51 +0000 (09:37 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-nand-flash
Albert ARIBAUD [Fri, 11 Oct 2013 12:47:25 +0000 (14:47 +0200)]
Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'
Stephen Warren [Wed, 9 Oct 2013 20:28:09 +0000 (14:28 -0600)]
buildman: don't fail --list-toolchains when toolchains fail
When a toolchain invocation fails, an exception is thrown but not caught
which then aborts the entire toolchain detection process. To solve this,
request that exceptions not be thrown, since the toolchain init code
already error-checks the command result. This solves e.g.:
- found '/usr/bin/winegcc'
Traceback (most recent call last):
...
Exception: Error running '/usr/bin/winegcc --version'
Change-Id: I579c72ab3b021e38b14132893c3375ea257c74f0
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
(formatted to 80cols)
Andrew Murray [Sun, 29 Sep 2013 17:02:22 +0000 (18:02 +0100)]
usb: Prevent using reserved registers on DM36x usb
The musb driver defines and uses MUSB_CSR0_H_DIS_PING, however this
bit is reserved on the DM36x. Thus this patch ensures that the
reserved bit is not accesssed.
It has been observed that some USB devices will fail to enumerate
with errors such as 'error in inquiry' without this patch.
See http://www.ti.com/litv/pdf/sprufh9a for details.
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Andrew Murray <amurray@embedded-bits.co.uk>
Acked-by: Marek Vasut <marex@denx.de>
Tom Rini [Wed, 9 Oct 2013 14:59:33 +0000 (10:59 -0400)]
omap5_common: Re-work mmc boot to try SD and eMMC, correct root device
OMAP5 boards may have both eMMC (on MMC2) and an SD slot (on MMC1). We
Update the default bootcmd to match what happens on AM335x where we try
SD first, and then eMMC. In this case however, the hardware layout used
for powering both of these means that in the kernel eMMC shall be found
first as it is powered by a fixed regulator and SD found second as SD is
powered via the palmas which will result in deferred probing.
Tested-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Paul Burton [Wed, 4 Sep 2013 14:16:59 +0000 (15:16 +0100)]
cmd_ubi: add write.part command, to write a volume in multiple parts
This allows you to write data to an UBI volume when the amount of memory
available to write that data from is less than the total size of the
data. For example, you may split a root filesystem UBIFS image into
parts, provide the total size of the image to the first write.part
command and then use multiple write.part commands to write the
subsequent parts of the volume. This results in a sequence of commands
akin to:
ext4load mmc 0:1 0x80000000 rootfs.ubifs.0
ubi write.part 0x80000000 root 0x08000000 0x18000000
ext4load mmc 0:1 0x80000000 rootfs.ubifs.1
ubi write.part 0x80000000 root 0x08000000
ext4load mmc 0:1 0x80000000 rootfs.ubifs.2
ubi write.part 0x80000000 root 0x08000000
This would write 384MiB of data to the UBI volume 'root' whilst only
requiring 128MiB of said data to be held in memory at a time.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Stefan Roese <sr@denx.de>
Paul Burton [Wed, 4 Sep 2013 14:16:58 +0000 (15:16 +0100)]
cmd_ubi: use int64_t volume size for 'ubi create'
int64_t matches the bytes field in struct ubi_mkvol_req to which the
size is assigned. With the prior signed 32 bit integer, volumes were
restricted to being less than 2GiB in size.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Stefan Roese <sr@denx.de>
Paul Burton [Wed, 4 Sep 2013 14:16:57 +0000 (15:16 +0100)]
cmd_mtdparts: use 64 bits for flash size, partition size & offset
This matches the 64 bit size in struct mtd_info and allows the mtdparts
command to function correctly with a flash >= 4GiB. Format specifiers
for size & offset are given the ll length, matching its use in
drivers/mtd in absence of something like inttypes.h/PRIx64.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Stefan Roese <sr@denx.de>
Paul Burton [Wed, 4 Sep 2013 14:16:56 +0000 (15:16 +0100)]
mtd: driver _read() returns max_bitflips; mtd_read() returns -EUCLEAN
Linux modified the MTD driver interface in commit
edbc4540 (with the
same name as this commit). The effect is that calls to mtd_read will
not return -EUCLEAN if the number of ECC-corrected bit errors is below
a certain threshold, which defaults to the strength of the ECC. This
allows -EUCLEAN to stop indicating "some bits were corrected" and begin
indicating "a large number of bits were corrected, the data held in
this region of flash may be lost soon". UBI makes use of this and when
-EUCLEAN is returned from mtd_read it will move data to another block
of flash. Without adopting this interface change UBI on U-boot attempts
to move data between blocks every time a single bit is corrected using
the ECC, which is a very common occurance on some devices.
For some devices where bit errors are common enough, UBI can get stuck
constantly moving data around because each block it attempts to use has
a single bit error. This condition is hit when wear_leveling_worker
attempts to move data from one PEB to another in response to an
-EUCLEAN/UBI_IO_BITFLIPS error. When this happens ubi_eba_copy_leb is
called to perform the data copy, and after the data is written it is
read back to check its validity. If that read returns UBI_IO_BITFLIPS
(in response to an MTD -EUCLEAN) then ubi_eba_copy_leb returns 1 to
wear_leveling worker, which then proceeds to schedule the destination
PEB for erasure. This leads to erase_worker running on the PEB, and
following a successful erase wear_leveling_worker is called which
begins this whole cycle all over again. The end result is that (without
UBI debug output enabled) the boot appears to simply hang whilst in
reality U-boot busily works away at destroying a block of the NAND
flash. Debug output from this situation:
UBI DBG: ensure_wear_leveling: schedule scrubbing
UBI DBG: wear_leveling_worker: scrub PEB 1027 to PEB 4083
UBI DBG: ubi_io_read_vid_hdr: read VID header from PEB 1027
UBI DBG: ubi_io_read: read 4096 bytes from PEB 1027:4096
UBI DBG: ubi_eba_copy_leb: copy LEB 0:0, PEB 1027 to PEB 4083
UBI DBG: ubi_eba_copy_leb: read 1040384 bytes of data
UBI DBG: ubi_io_read: read 1040384 bytes from PEB 1027:8192
UBI: fixable bit-flip detected at PEB 1027
UBI DBG: ubi_io_write_vid_hdr: write VID header to PEB 4083
UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:4096
UBI DBG: ubi_io_read_vid_hdr: read VID header from PEB 4083
UBI DBG: ubi_io_read: read 4096 bytes from PEB 4083:4096
UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:8192
UBI DBG: ubi_io_read: read 4096 bytes from PEB 4083:8192
UBI: fixable bit-flip detected at PEB 4083
UBI DBG: schedule_erase: schedule erasure of PEB 4083, EC 55, torture 0
UBI DBG: erase_worker: erase PEB 4083 EC 55
UBI DBG: sync_erase: erase PEB 4083, old EC 55
UBI DBG: do_sync_erase: erase PEB 4083
UBI DBG: sync_erase: erased PEB 4083, new EC 56
UBI DBG: ubi_io_write_ec_hdr: write EC header to PEB 4083
UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:0
UBI DBG: ensure_wear_leveling: schedule scrubbing
UBI DBG: wear_leveling_worker: scrub PEB 1027 to PEB 4083
...
This patch adopts the interface change as in Linux commit
edbc4540 in
order to avoid such situations. Given that none of the drivers under
drivers/mtd return -EUCLEAN, this should only affect those using
software ECC. I have tested that it works on a board which is
currently out of tree, but which I hope to be able to begin
upstreaming soon.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Stefan Roese <sr@denx.de>
Andreas Huber [Thu, 4 Jul 2013 13:37:34 +0000 (15:37 +0200)]
km/scripts: fix ramfs
'actual_bank' is not used anymore, instead boot_bank is used.
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Holger Brunck [Thu, 4 Jul 2013 13:37:33 +0000 (15:37 +0200)]
powerpc/km: drop unused CONFIG_SYS_DTT_LOW_TEMP
This define is not used in u-boot code, we can drop this define safely.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Holger Brunck [Thu, 4 Jul 2013 13:37:32 +0000 (15:37 +0200)]
km/common: switch on CMD_GREPENV
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Holger Brunck [Thu, 4 Jul 2013 13:37:31 +0000 (15:37 +0200)]
powerpc/83xx: remove staticness for qe_iop_conf_tab
commit
a5510058 powerpc/83xx/km: make local functions and structs static
removed the staticness also from this struct. But this struct is needed
in arch/powerpc/cpu/mpc83xx/cpu_init.c and declared as extern.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Tom Rini [Wed, 9 Oct 2013 14:06:40 +0000 (10:06 -0400)]
Merge branch 'next' of git://git.denx.de/u-boot-mpc83xx
Tom Rini [Tue, 8 Oct 2013 19:08:38 +0000 (15:08 -0400)]
da850evm.h: Always set CONFIG_CMD_SF, move to by CONFIG_SPI_FLASH
When we have CONFIG_SPI_FLASH set we now require CONFIG_CMD_SF.
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Tue, 8 Oct 2013 15:09:17 +0000 (11:09 -0400)]
Revert "am335x_evm.h: If mmcdev and bootpart switch to mmcdev 1, so should mmcroot."
Upon further inspection and review and chatting with kernel folks, what
happens here is that what mmcblk# a device gets is based on probe order.
So a system with an SD card inserted with place eMMC on mmcblk1, but
without an SD card, it will be on mmcblk0. So U-boot can only provide a
best guess. In this case, if no SD card is present, we would want to
pass mmcblk0p2 still. If an SD card is present, it woudl be able to
provide a uEnv.txt that would be loaded (even if the kernel is NOT
there) which can still update mmcroot variable.
This reverts commit
827512fb1154c05c6eb1e2259e936df55c98a535.
Cc: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Tue, 8 Oct 2013 13:51:48 +0000 (09:51 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Tom Rini [Tue, 8 Oct 2013 13:03:15 +0000 (09:03 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-spi
Rajeshwari Shinde [Tue, 8 Oct 2013 10:50:06 +0000 (16:20 +0530)]
spi: exynos: Support word transfers
Since SPI register access is so expensive, it is worth transferring data
a word at a time if we can. This complicates the driver unfortunately.
Use the byte-swapping feature to avoid having to convert to/from big
endian in software.
This change increases speed from about 2MB/s to about 4.5MB/s.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Rajeshwari Shinde [Tue, 8 Oct 2013 10:50:05 +0000 (16:20 +0530)]
spi: exynos: Minimise access to SPI FIFO level
Accessing SPI registers is slow, but access to the FIFO level register
in particular seems to be extraordinarily expensive (I measure up to
600ns). Perhaps it is required to synchronise with the SPI byte output
logic which might run at 1/8th of the 40MHz SPI speed (just a guess).
Reduce access to this register by filling up and emptying FIFOs
more completely, rather than just one word each time around the inner
loop.
Since the rxfifo value will now likely be much greater that what we read
before we fill the txfifo, we only fill the txfifo halfway. This is
because if the txfifo is empty, but the rxfifo has data in it, then writing
too much data to the txfifo may overflow the rxfifo as data arrives.
This speeds up SPI flash reading from about 1MB/s to about 2MB/s on snow.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Rajeshwari Shinde [Tue, 8 Oct 2013 10:50:04 +0000 (16:20 +0530)]
spi: exynos: Support a delay after deactivate
For devices that need some time to react after a spi transaction
finishes, add the ability to set a delay.
Implement this as a delay on the first/next transaction to avoid
any delay in the fairly common case where a SPI transaction is
followed by other processing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Rajeshwari Shinde [Tue, 8 Oct 2013 10:50:03 +0000 (16:20 +0530)]
exynos: Export timer_get_us() to get microsecond timer
This function, if implemented by the board, provides a microsecond
timer. The granularity may be larger than 1us if hardware does not
support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Wolfgang Denk [Sat, 5 Oct 2013 19:07:25 +0000 (21:07 +0200)]
Fix number base handling of "load" command
As documented, almost all U-Boot commands expect numbers to be entered
in hexadecimal input format. (Exception: for historical reasons, the
"sleep" command takes its argument in decimal input format.)
This rule was broken for the "load" command; for details please see
especially commits 045fa1e "fs: add filesystem switch libary,
implement ls and fsload commands" and 3f83c87 "fs: fix number base
behaviour change in fatload/ext*load". In the result, the load
command would always require an explicit "0x" prefix for regular
(i. e. base 16 formatted) input.
Change this to use the standard notation of base 16 input format.
While strictly speaking this is a change of the user interface, we
hope that it will not cause trouble. Stephen Warren comments (see
[1]):
I suppose you can change the behaviour if you want; anyone
writing "0x..." for their values presumably won't be
affected, and if people really do assume all values in U-Boot
are in hex, presumably nobody currently relies upon using
non-prefixed values with the generic load command, since it
doesn't work like that right now.
[1] http://article.gmane.org/gmane.comp.boot-loaders.u-boot/171172
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Chin Liang See [Wed, 11 Sep 2013 16:26:10 +0000 (11:26 -0500)]
socfpga: Adding pin mux handoff files
Adding the generated pin mux configuration by Preloader
Generator tool
Signed-off-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Chin Liang See [Wed, 11 Sep 2013 16:24:48 +0000 (11:24 -0500)]
socfpga: Adding System Manager driver
Adding System Manager driver which will configure the
pin mux for real hardware Cyclone V development kit
(not Virtual Platform)
Signed-off-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Albert ARIBAUD [Mon, 23 Sep 2013 17:11:38 +0000 (19:11 +0200)]
omap1510inn: arm925t: remove support
omap1510inn is orphan and has been for years now.
Reove it and, as it was the only arm925t target,
also remove arm925t support.
Update doc/README.scrapyard accordingly.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Jagannadha Sutradharudu Teki [Mon, 7 Oct 2013 12:03:20 +0000 (17:33 +0530)]
doc: SPI: Update SPI status track
Updated SPI/status.txt, with memory_map and TODO.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Jagannadha Sutradharudu Teki [Mon, 7 Oct 2013 11:51:20 +0000 (17:21 +0530)]
sf: ramtron: Remove page_size print
There is no page_size for ramtron flashes,
so just print the detected flash and it's size.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Jagannadha Sutradharudu Teki [Mon, 7 Oct 2013 14:04:56 +0000 (19:34 +0530)]
sf: Minor cleanups
- Add spaces, tabs
- Commenting.
- Rearrange code.
- Add static qualifier for missing func.
- Remove memory_map from ramtron.c
- Ramtron: spi_flash_internal.h -> sf_internal.h
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Poddar, Sourav [Mon, 7 Oct 2013 10:23:04 +0000 (15:53 +0530)]
README: qspi usecase and testing documentation.
Contains documentation and testing details for qspi flash
interface.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Matt Porter [Mon, 7 Oct 2013 10:23:03 +0000 (15:53 +0530)]
dra7xx_evm: add SPL API, QSPI, and serial flash support
Enables support for SPI SPL, QSPI and Spansion serial flash device
on the EVM. Configures pin muxes for QSPI mode.
Signed-off-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Matt Porter [Mon, 7 Oct 2013 10:23:02 +0000 (15:53 +0530)]
spi: add TI QSPI driver
Adds a SPI master driver for the TI QSPI peripheral.
- Added quad read support.
- Added memory mapped support.
Signed-off-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Poddar, Sourav [Mon, 7 Oct 2013 10:23:01 +0000 (15:53 +0530)]
sf: Add memory mapped read support
Qspi controller can have a memory mapped port which can be used for
data read. Added support to enable memory mapped port read.
This patch enables the following:
- It enables exchange of memory map address between mtd and qspi
through the introduction of "memory_map" flag.
- Add support to communicate to the driver that memory mapped
transfer is to be started through introduction of new flags like
"SPI_XFER_MEM_MAP" and "SPI_XFER_MEM_MAP_END".
This will enable the spi controller to do memory mapped configurations
if required.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Poddar, Sourav [Mon, 7 Oct 2013 10:23:00 +0000 (15:53 +0530)]
armv7: hw_data: change clock divider setting.
Clock requirement for qspi clk is 192 Mhz.
According to the below formulae,
f dpll = f ref * 2 * m /(n + 1)
clockoutx2_Hmn = f dpll / (hmn+ 1)
fref = 20 Mhz, m = 96, n = 4 gives f dpll = 768 Mhz
For clockoutx2_Hmn to be 768, hmn + 1 should be 4.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Matt Porter [Mon, 7 Oct 2013 10:22:59 +0000 (15:52 +0530)]
omap5: add qspi support
Add QSPI definitions and clock configuration support.
Signed-off-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Priyanka Jain [Thu, 3 Oct 2013 15:37:00 +0000 (21:07 +0530)]
sf: probe: Add support for EN25S64
Add support for EON EN25S64 SPI flash.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Jagannadha Sutradharudu Teki [Thu, 26 Sep 2013 10:25:52 +0000 (15:55 +0530)]
doc: SPI: Add status.txt for tracking SPI subsys status
doc/SPI/status.txt added to track the u-boot SPI subsystem status.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Jagannadha Sutradharudu Teki [Thu, 26 Sep 2013 10:30:15 +0000 (16:00 +0530)]
sf: Rename spi_flash files
Renamed:
spi_flash.c -> sf.c
spi_flash_internal.h -> sf_internal.h
spi_flash_ops.c -> sf_ops.c
spi_flash_probe.c -> sf_probe.c
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Jagannadha Sutradharudu Teki [Wed, 25 Sep 2013 10:17:36 +0000 (15:47 +0530)]
spi: spi cleanups
- Rearranged multi-line comment style.
- Add tabs.
- Add spaces.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Jagannadha Sutradharudu Teki [Wed, 2 Oct 2013 14:08:49 +0000 (19:38 +0530)]
sf: spi_flash cleanups
More cleanups on spi_flash side:
- Removed unneeded comments.
- Rearranged macros in proper location.
- Rearranged func declerations
- Renamed few function names.
- Added License headers.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Jagannadha Sutradharudu Teki [Wed, 7 Aug 2013 16:06:25 +0000 (21:36 +0530)]
sf: Remove spi_flash_do_alloc references
Added a support for common probe, hence removed removed
spi_flash_do_alloc reference.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Jagannadha Sutradharudu Teki [Wed, 28 Aug 2013 09:19:13 +0000 (14:49 +0530)]
sf: probe: Add support for MX25L51235F
Add support for Macronix MX25L51235F SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Jagannadha Sutradharudu Teki [Wed, 28 Aug 2013 09:16:49 +0000 (14:46 +0530)]
sf: probe: Add support for MX25L25635F
Add support for Macronix MX25L25635F SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Jagannadha Sutradharudu Teki [Wed, 28 Aug 2013 09:27:03 +0000 (14:57 +0530)]
sf: ops: Add static qualifier to spi_flash_cmd_bankaddr_write
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Jagannadha Sutradharudu Teki [Sun, 15 Sep 2013 17:36:12 +0000 (23:06 +0530)]
sf: probe: Print erase_size while printing flash details
Included erase_size while printing probed flash details.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>