Anton Blanchard [Wed, 30 Nov 2011 00:23:16 +0000 (00:23 +0000)]
powerpc/kdump: Delay before sending IPI on a system reset
If we enter the kdump code via system reset, wait a bit before
sending the IPI to capture all secondary CPUs. Without it we race
with the hypervisor that is issuing the system reset to each CPU.
If the IPI gets there first the system reset oops output then shows
the register state of the IPI handler which is not what we want.
I took the opportunity to add defines for all the various delays
we have. There's no need for cpu_relax when we are doing an mdelay,
so remove them too.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 30 Nov 2011 00:23:15 +0000 (00:23 +0000)]
powerpc/xics: Reset the CPPR if H_EOI fails
I have an intermittent kdump fail where the hypervisor fails an H_EOI.
As a result our CPPR is never reset to 0xff and we no longer accept
interrupts.
This patch calls icp_hv_set_cppr to reset the CPPR if H_EOI fails,
fixing the kdump fail.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 30 Nov 2011 00:23:14 +0000 (00:23 +0000)]
powerpc: Reduce pseries panic timeout from 180s to 10s
We've had a 180 second panic timeout on ppc64 for as long as I
can remember. This patch reduces it to 10 seconds on pseries for a few
reasons:
- Almost all pseries machines have a hypervisor console so panic
output will be available in a scrollback buffer.
- The 180 seconds impacts our availability, users (other than
kernel hackers) just want the box to come back around so it
can continue its work.
- I spend a lot of my life staring at the 180 second panic timeout.
Many pseries machines take minutes to power cycle, so it's quicker
to sit through the 180 seconds than it is to power cycle.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 30 Nov 2011 00:23:13 +0000 (00:23 +0000)]
powerpc: Rework die()
Our die() code was based off a very old x86 version. Update it to
mirror the current x86 code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 30 Nov 2011 00:23:12 +0000 (00:23 +0000)]
powerpc: Cleanup crash/kexec code
Remove some unnecessary defines and fix some spelling mistakes.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 30 Nov 2011 00:23:11 +0000 (00:23 +0000)]
powerpc/kdump: Use setjmp/longjmp to handle kdump and system reset recursion
We can handle recursion caused by system reset by reusing the crash
shutdown fault handler.
Since we don't have an OS triggerable NMI, if all CPUs don't make it
into kdump then we tell the user to issue a system reset. However if
we have a panic timeout set we cannot wait forever and must continue
the kdump.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 30 Nov 2011 00:23:10 +0000 (00:23 +0000)]
powerpc: Remove broken and complicated kdump system reset code
We have a lot of complicated logic that handles possible recursion between
kdump and a system reset exception. We can solve this in a much simpler
way using the same setjmp/longjmp tricks xmon does.
As a first step, this patch removes the old system reset code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 30 Nov 2011 00:23:09 +0000 (00:23 +0000)]
powerpc: Give us time to get all oopses out before panicking
I've been seeing truncated output when people send system reset info
to me. We should see a backtrace for every CPU, but the panic() code
takes the box down before they all make it out to the console. The
panic code runs unlocked so we also see corrupted console output.
If we are going to panic, then delay 1 second before calling into the
panic code. Move oops_exit inside the die lock and put a newline
between oopses for clarity.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt [Thu, 8 Dec 2011 02:20:34 +0000 (13:20 +1100)]
Merge branch 'booke-hugetlb' into next
Benjamin Herrenschmidt [Wed, 7 Dec 2011 07:22:47 +0000 (18:22 +1100)]
Merge branch 'mpic' into next
Benjamin Herrenschmidt [Tue, 29 Nov 2011 20:16:25 +0000 (20:16 +0000)]
powerpc/pci: Make pci_read_irq_line() static
It's only used inside the same file where it's defined. There's
also no point exporting it anymore.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt [Tue, 29 Nov 2011 18:22:56 +0000 (18:22 +0000)]
powerpc/powernv: Workaround OFW issues in prom_init.c
Open Firmware on OPAL machines seems to have issues if we close
stdin and/or we try to print things after calling "quiesce" so
we avoid doing both.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt [Tue, 29 Nov 2011 18:22:53 +0000 (18:22 +0000)]
powerpc/powernv: Display diag data on p7ioc EEH errors
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt [Tue, 29 Nov 2011 18:22:50 +0000 (18:22 +0000)]
powerpc/powernv: Update OPAL interfaces
This adds some more interfaces for OPAL v2
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Becky Bruce [Tue, 29 Nov 2011 15:10:39 +0000 (15:10 +0000)]
powerpc: Define/use HUGETLB_NEED_PRELOAD insead of complicated #if
Define HUGETLB_NEED_PRELOAD in mmu-book3e.h for CONFIG_PPC64 instead
of having a much more complicated #if block. This is easier to read
and maintain.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Becky Bruce [Mon, 28 Nov 2011 14:43:33 +0000 (14:43 +0000)]
powerpc/book3e: Change hugetlb preload to take vma argument
This avoids an extra find_vma() and is less error-prone.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Becky Bruce [Mon, 10 Oct 2011 10:50:48 +0000 (10:50 +0000)]
powerpc: Enable hugetlb by default for corenet64 platforms
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Becky Bruce [Mon, 10 Oct 2011 10:50:46 +0000 (10:50 +0000)]
powerpc: Enable Hugetlb by default for 32-bit 85xx/corenet
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Becky Bruce [Mon, 10 Oct 2011 10:50:44 +0000 (10:50 +0000)]
powerpc: Kconfig updates for FSL BookE HUGETLB 64-bit
Allow hugetlb to be enabled on 64b FSL_BOOK3E. No platforms enable
it by default yet.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Becky Bruce [Mon, 10 Oct 2011 10:50:43 +0000 (10:50 +0000)]
powerpc: Add gpages reservation code for 64-bit FSL BOOKE
For 64-bit FSL_BOOKE implementations, gigantic pages need to be
reserved at boot time by the memblock code based on the command line.
This adds the call that handles the reservation, and fixes some code
comments.
It also removes the previous pr_err when reserve_hugetlb_gpages
is called on a system without hugetlb enabled - the way the code is
structured, the call is unconditional and the resulting error message
spurious and confusing.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Becky Bruce [Mon, 10 Oct 2011 10:50:42 +0000 (10:50 +0000)]
powerpc: Add hugepage support to 64-bit tablewalk code for FSL_BOOK3E
Before hugetlb, at each level of the table, we test for
!0 to determine if we have a valid table entry. With hugetlb, this
compare becomes:
< 0 is a normal entry
0 is an invalid entry
> 0 is huge
This works because the hugepage code pulls the top bit off the entry
(which for non-huge entries always has the top bit set) as an
indicator that we have a hugepage.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Becky Bruce [Mon, 10 Oct 2011 10:50:41 +0000 (10:50 +0000)]
powerpc: Whitespace/comment changes to tlb_low_64e.S
I happened to comment this code while I was digging through it;
we might as well commit that. I also made some whitespace
changes - the existing code had a lot of unnecessary newlines
that I found annoying when I was working on my tiny laptop.
No functional changes.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Becky Bruce [Mon, 10 Oct 2011 10:50:40 +0000 (10:50 +0000)]
powerpc: hugetlb: modify include usage for FSL BookE code
The original 32-bit hugetlb implementation used PPC64 vs PPC32 to
determine which code path to take. However, the final hugetlb
implementation for 64-bit FSL ended up shared with the FSL
32-bit code so the actual check needs to be FSL_BOOK3E vs
everything else. This patch changes the include protections to
reflect this.
There are also a couple of related comment fixes.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Becky Bruce [Mon, 10 Oct 2011 10:50:39 +0000 (10:50 +0000)]
powerpc: Update hugetlb huge_pte_alloc and tablewalk code for FSL BOOKE
This updates the hugetlb page table code to handle 64-bit FSL_BOOKE.
The previous 32-bit work counted on the inner levels of the page table
collapsing.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Becky Bruce [Mon, 10 Oct 2011 10:50:38 +0000 (10:50 +0000)]
powerpc: Fix booke hugetlb preload code for PPC_MM_SLICES and 64-bit
This patch does 2 things: It corrects the code that determines the
size to write into MAS1 for the PPC_MM_SLICES case (this originally
came from David Gibson and I had incorrectly altered it), and it
changes the methodolody used to calculate the size for !PPC_MM_SLICES
to work for 64-bit as well as 32-bit.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Becky Bruce [Mon, 10 Oct 2011 10:50:37 +0000 (10:50 +0000)]
powerpc: hugetlb: fix huge_ptep_set_access_flags return value
There was an unconditional return of "1" in the original code
from David Gibson, and I dropped it because it wasn't needed
for FSL BOOKE 32-bit. However, not all systems (including 64-bit
FSL BOOKE) do loading of the hpte from the fault handler asm
and depend on this function returning 1, which causes a call
to update_mmu_cache() that writes an entry into the tlb.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Becky Bruce [Mon, 10 Oct 2011 10:50:36 +0000 (10:50 +0000)]
powerpc: Only define HAVE_ARCH_HUGETLB_UNMAPPED_AREA if PPC_MM_SLICES
If we don't have slices, we should be able to use the generic
hugetlb_get_unmapped_area() code
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kyle Moffett [Fri, 2 Dec 2011 06:28:07 +0000 (06:28 +0000)]
powerpc/mpic: Add in-core support for cascaded MPICs
The Cell and PowerMac platforms use virtually identical cascaded-IRQ
setup code, so just merge it into the core. Ideally this code would
trigger automatically when an MPIC device-node specifies an "interrupts"
property, perhaps even enabling MPIC_SECONDARY along the way.
Unfortunately, Benjamin Herrenschmidt has had bad experiences in the
past with the quality of Apple PowerMac device-trees, so to be safe we
will only try to parse out an IRQ if the MPIC_SECONDARY flag is set by
the caller.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kyle Moffett [Fri, 2 Dec 2011 06:28:06 +0000 (06:28 +0000)]
powerpc/mpic: Cache the device-tree node in "struct mpic"
Store the node pointer in the MPIC during initialization so that all of
the later operational code can just reuse the cached pointer.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kyle Moffett [Fri, 2 Dec 2011 06:28:05 +0000 (06:28 +0000)]
powerpc/mpic: Put "pic-no-reset" test back into the MPIC code
There's not really any reason to have this one-liner in a separate
static inline function, given that all the other similar tests are
already in the alloc_mpic() code.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kyle Moffett [Fri, 2 Dec 2011 06:28:04 +0000 (06:28 +0000)]
powerpc/mpic: Don't open-code dcr_resource_start
Don't open-code the OpenFirmware "dcr-reg" property lookup trying to map
DCR resources. This makes the code a bit easier to read.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kyle Moffett [Fri, 2 Dec 2011 06:28:03 +0000 (06:28 +0000)]
powerpc/mpic: Invert the meaning of MPIC_PRIMARY
It turns out that there are only 2 in-tree platforms which use MPICs
which are not "primary": IBM Cell and PowerMac. To reduce the
complexity of the typical board setup code, invert the MPIC_PRIMARY bit
into MPIC_SECONDARY.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kyle Moffett [Fri, 2 Dec 2011 06:28:02 +0000 (06:28 +0000)]
powerpc/mpic: Search for open-pic device-tree node if NULL
Almost all PowerPC platforms use a standard "open-pic" device node so
the mpic_alloc() function now accepts NULL for the device-node. This
will cause it to perform a default search with of_find_matching_node().
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kyle Moffett [Fri, 2 Dec 2011 06:28:01 +0000 (06:28 +0000)]
powerpc/mpic: Save computed phys_addr for board-specific code
The MPIC code can already perform an automatic OF address translation
step as part of mpic_alloc(), but several boards need to use that base
address when they perform mpic_assign_isu().
The easiest solution is to save the computed physical address into the
"struct mpic" for later use by the board code.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kyle Moffett [Fri, 2 Dec 2011 06:28:00 +0000 (06:28 +0000)]
powerpc/mpic: Assume a device-node was passed in mpic_alloc()
All of the existing callers of mpic_alloc() pass in a non-NULL
device-node pointer, so the checks for a NULL device-node may be
removed.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kyle Moffett [Fri, 2 Dec 2011 06:27:59 +0000 (06:27 +0000)]
powerpc: Consolidate mpic_alloc() OF address translation
Instead of using the open-coded "reg" property lookup and address
translation in mpic_alloc(), directly call of_address_to_resource().
This includes various workarounds for special cases which the naive
of_address_translate() does not.
Afterwards it is possible to remove the copiously copy-pasted calls to
of_address_translate() from the 85xx/86xx/powermac platforms.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kyle Moffett [Fri, 2 Dec 2011 06:27:58 +0000 (06:27 +0000)]
powerpc/85xx: Move mpc85xx_smp_init() decl to a new "smp.h"
This removes a bunch of "extern" declarations and CONFIG_SMP ifdefs.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Dan McGee [Mon, 17 Oct 2011 13:05:23 +0000 (13:05 +0000)]
powerpc+sparc64/mm: Remove hack in mmap randomize layout
Since commit
8a0a9bd4db63bc45e301, this comment in mmap_rnd() does not
hold true as the value returned by get_random_int() will in fact be
different every single call. Remove the comment and simplify the code
back to its original desired form.
This reverts commit
a5adc91a4b44b5d1 which is no longer necessary and
also fixes the sparc code that copied this same adjustment.
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Thu, 24 Nov 2011 19:39:36 +0000 (19:39 +0000)]
powerpc/xics: Harden xics hypervisor backend
During kdump stress testing I sometimes see the kdump kernel panic
with:
Interrupt 0x306 (real) is invalid, disabling it.
Kernel panic - not syncing: bad return code EOI - rc = -4, value=
ff000306
Instead of panicing print the error message, dump the stack the first
time it happens and continue on. Add some more information to the
debug messages as well.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Thu, 24 Nov 2011 19:35:57 +0000 (19:35 +0000)]
powerpc: Decode correct MSR bits in oops output
On a 64bit book3s machine I have an oops from a system reset that
claims the book3e CE bit was set:
MSR:
8000000000021032 <ME,CE,IR,DR> CR:
24004082 XER:
00000010
On a book3s machine system reset sets IBM bit 46 and 47 depending on
the power saving mode. Separate the definitions by type and for
completeness add the rest of the bits in.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Matthew McClintock [Tue, 7 Sep 2010 08:56:55 +0000 (08:56 +0000)]
arch/powerpc: Remove duplicate/redundant Altivec entries
In lieu of having multiple similiar lines, we can just have one
generic cpu-as line for CONFIG_ALTIVEC
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Dmitry Eremin-Solenikov [Wed, 29 Jun 2011 04:17:40 +0000 (04:17 +0000)]
powerpc/maple: Enable access to HT Host-Bridge on Maple
CPC925/CPC945 use special window to access host bridge functionality of
u3-ht. Provide a way to access this device.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
sukadev@linux.vnet.ibm.com [Tue, 30 Aug 2011 09:19:17 +0000 (09:19 +0000)]
powerpc: Implement CONFIG_STRICT_DEVMEM
As described in the help text in the patch, this token restricts general
access to /dev/mem as a way of increasing the security. Specifically, access
to exclusive IOMEM and kernel RAM is denied unless CONFIG_STRICT_DEVMEM is
set to 'n'.
Implement the 'devmem_is_allowed()' interface for Powerpc. It will be
called from range_is_allowed() when userpsace attempts to access /dev/mem.
This patch is based on an earlier patch from Steve Best and with input from
Paul Mackerras and Scott Wood.
[BenH] Fixed a typo or two and removed the generic change which should
be submitted as a separate patch
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt [Fri, 25 Nov 2011 04:25:39 +0000 (15:25 +1100)]
Merge remote-tracking branch 'kumar/next' into next
Justin P. Mattock [Mon, 21 Nov 2011 06:43:26 +0000 (06:43 +0000)]
powerpc/mpic: Remove extra semicolon.
The patch below removes an extra semicolon.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
CC: linuxppc-dev@lists.ozlabs.org
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Ananth N Mavinakayanahalli [Thu, 10 Nov 2011 19:58:53 +0000 (19:58 +0000)]
powerpc: Export PIR data through sysfs
On Fri, Nov 11, 2011 at 10:17:55AM +0530, Ananth N Mavinakayanahalli wrote:
> >
> > At this rate we're going to end up with no bits left for CPU features
> > way too quickly... Especially for something we only care about once at
> > boot time.
> >
> > Wouldn't CPU_FTR_PPCAS_ARCH_V2 be a good enough test ?
>
> /me checks Cell manuals... yes, that test would be good enough. I will
> cook up a patch to use this.
Here it is...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt [Tue, 15 Nov 2011 17:29:08 +0000 (17:29 +0000)]
powerpc/powernv: PCI support for p7IOC under OPAL v2
This adds support for p7IOC (and possibly other IODA v1 IO Hubs)
using OPAL v2 interfaces.
We completely take over resource assignment and assign them using an
algorithm that hands out device BARs in a way that makes them fit in
individual segments of the M32 window of the bridge, which enables us
to assign individual PEs to devices and functions.
The current implementation gives out a PE per functions on PCIe, and a
PE for the entire bridge for PCIe to PCI-X bridges.
This can be adjusted / fine tuned later.
We also setup DMA resources (32-bit only for now) and MSIs (both 32-bit
and 64-bit MSI are supported).
The DMA allocation tries to divide the available 256M segments of the
32-bit DMA address space "fairly" among PEs. This is done using a
"weight" heuristic which assigns less value to things like OHCI USB
controllers than, for example SCSI RAID controllers. This algorithm
will probably want some fine tuning for specific devices or device
types.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt [Sun, 6 Nov 2011 18:56:00 +0000 (18:56 +0000)]
powerpc/powernv: Fixup p7ioc PCIe root complex class code
It advertises "host bridge" instead of "PCI to PCI bridge" which confuses
the Linux probe code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt [Sun, 6 Nov 2011 18:55:59 +0000 (18:55 +0000)]
powerpc/powernv: Add TCE SW invalidation support
This is used for newer IO Hubs such as p7IOC.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt [Sun, 6 Nov 2011 18:55:58 +0000 (18:55 +0000)]
powerpc/pci: Change how re-assigning resouces work
When PCI_REASSIGN_ALL_RSRC is set, we used to clear all bus resources
at the beginning of survey and re-allocate them later.
This changes it so instead, during early fixup, we mark all resources
as IORESOURCE_UNSET and move them down to be 0-based.
Later, if bus resources are still unset at the beginning of the survey,
then we clear them.
This shouldn't impact the re-assignment case on 4xx, but will enable
us to have the platform do some custom resource assignment before the
survey, by clearing individual resources IORESOURCE_UNSET bit.
Also limits the clutter in the kernel log from fixup when re-assigning
since we don't care about the offset applied to the BAR values in this
case.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt [Sun, 6 Nov 2011 18:55:57 +0000 (18:55 +0000)]
powerpc/pci: Add a platform hook after probe and before resource survey
Some platforms need to perform resource allocation using a custom algorithm
due to HW constraints, or may want to tweak things globally below a host
bridge. For example OPAL support for IODA will need to perform a
resource allocation pass that applies IODA specific segmentation
constraints to MMIO which cannot be done simply using the kernel generic
resource management code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Geoff Thorpe [Thu, 27 Oct 2011 02:58:45 +0000 (02:58 +0000)]
powerpc: Add pgprot_cached_noncoherent()
This adds a pgprot combination required by some cache-enabled IO device
mappings, such as Freescale datapath (QMan and BMan) portals.
Signed-off-by: Geoff Thorpe <geoff@geoffthorpe.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Thomas Gleixner [Wed, 5 Oct 2011 02:30:51 +0000 (02:30 +0000)]
powerpc: Allow irq threading
All interrupts which must be non threaded are marked
IRQF_NO_THREAD. So it's safe to allow force threaded handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Thomas Gleixner [Wed, 5 Oct 2011 02:30:50 +0000 (02:30 +0000)]
powerpc: Mark IPI interrupts IRQF_NO_THREAD
IPI handlers cannot be threaded. Remove the obsolete IRQF_DISABLED
flag (see commit
e58aa3d2) while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Thomas Gleixner [Wed, 5 Oct 2011 02:30:50 +0000 (02:30 +0000)]
powerpc/wsp: Mark opb cascade handler IRQF_NO_THREAD
Cascade handlers must run in hard interrupt context.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Thomas Gleixner [Wed, 5 Oct 2011 02:30:49 +0000 (02:30 +0000)]
powerpc/85xx: Mark cascade irq IRQF_NO_THREAD
Cascade interrupt must run in hard interrupt context.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Ravi K. Nittala [Mon, 3 Oct 2011 21:49:53 +0000 (21:49 +0000)]
powerpc/pseries: Cancel RTAS event scan before firmware flash
The RTAS firmware flash update is conducted using an RTAS call that is
serialized by lock_rtas() which uses spin_lock. While the flash is in
progress, rtasd performs scan for any RTAS events that are generated by
the system. rtasd keeps scanning for the RTAS events generated on the
machine. This is performed via workqueue mechanism. The rtas_event_scan()
also uses an RTAS call to scan the events, eventually trying to acquire
the spin_lock before issuing the request.
The flash update takes a while to complete and during this time, any other
RTAS call has to wait. In this case, rtas_event_scan() waits for a long time
on the spin_lock resulting in a soft lockup.
Fix: Just before the flash update is performed, the queued rtas_event_scan()
work item is cancelled from the work queue so that there is no other RTAS
call issued while the flash is in progress. After the flash completes, the
system reboots and the rtas_event_scan() is rescheduled.
Signed-off-by: Suzuki Poulose <suzuki@in.ibm.com>
Signed-off-by: Ravi Nittala <ravi.nittala@in.ibm.com>
Reported-by: Divya Vikas <divya.vikas@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jimi Xenidis [Fri, 30 Sep 2011 04:26:13 +0000 (04:26 +0000)]
powerpc/book3e: Add Chroma as a new WSP/PowerEN platform.
This patch add the Chroma platform to WSP/PowerEN, which is a PCIe
card (a defconfig is included).
The card includes an H8 service processor that is used to manage the
card. The H8 is connected over the second serial UART on the PowerEN
chip so this patch includes a simple 16550 driver to enable
communication, mostly for "power off" and "rebooting".
This patch also includes a, WSP specific, "halt" method that will shut
of all A2 cores but still leave power on at the chip level. This is
desirable, especially if you wish to interrogate the chip with a
hardware probe after the halt.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jimi Xenidis [Thu, 29 Sep 2011 12:05:28 +0000 (12:05 +0000)]
powerpc/xmon: Fix #if typo for systems without MSR[RI]
Sorry, there was a typo in the #if
signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jimi Xenidis [Thu, 29 Sep 2011 11:25:10 +0000 (11:25 +0000)]
powerpc/xmon: Fix the 'u' command description
The 'u' command will print the TLB on book3e parts and the SLB on
Book3s parts, but the help system doesn't say that correctly.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jimi Xenidis [Thu, 29 Sep 2011 10:55:14 +0000 (10:55 +0000)]
powerpc/icswx: Simple ACOP fault handler
This patch adds a fault handler that responds to illegal Coprocessor
types. Currently all CTs are treated and illegal. There are two ways
to report the fault back to the application. If the application used
the record form ("icswx.") then the architected "reject" is emulated.
If the application did not used the record form ("icswx") then it is
selectable by config whether the failure is silent (as architected) or
a SIGILL is generated.
In all cases pr_warn() is used to log the bad CT.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jimi Xenidis [Thu, 29 Sep 2011 10:55:13 +0000 (10:55 +0000)]
powerpc/book3e: Add ICSWX/ACOP support to Book3e cores like A2
ICSWX is also used by the A2 processor to access coprocessors,
although not all "chips" that contain A2s have coprocessors.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jimi Xenidis [Thu, 29 Sep 2011 10:55:12 +0000 (10:55 +0000)]
powerpc: Split ICSWX ACOP and PID processing
Some processors, like embedded, that already have a PID register that
is managed by the system. This patch separates the ACOP and PID
processing into separate files so that the ACOP code can be shared.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Florian Fainelli [Tue, 23 Aug 2011 02:20:08 +0000 (02:20 +0000)]
perf/powerpc: Fix build for PowerPC with uclibc toolchains
libio.h is not provided by uClibc, in order to be able to test the
definition of __UCLIBC__ we need to include stdlib.h, which also
includes stddef.h, providing the definition of 'NULL'.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Julia Lawall [Sun, 21 Aug 2011 06:10:01 +0000 (06:10 +0000)]
powerpc/powermac: Add missing of_node_put
np is initialized to the result of calling a function that calls
of_node_get, so of_node_put should be called before the pointer is dropped.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1,e2;
@@
* e = \(of_find_node_by_type\|of_find_node_by_name\)(...)
... when != of_node_put(e)
when != true e == NULL
when != e2 = e
e = e1
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Julia Lawall [Sun, 21 Aug 2011 06:10:00 +0000 (06:10 +0000)]
powerpc/cell/iommu: Add missing of_node_put
np is initialized to the result of calling a function that calls
of_node_get, so of_node_put should be called before the pointer is dropped.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1,e2;
@@
* e = \(of_find_node_by_type\|of_find_node_by_name\)(...)
... when != of_node_put(e)
when != true e == NULL
when != e2 = e
e = e1
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Milton Miller [Wed, 29 Jun 2011 20:58:33 +0000 (20:58 +0000)]
powerpc/pseries: Software invalidatation of TCEs
Some pseries IOMMUs cache TCEs but don't snoop when the TCEs are changed
in memory, hence we need manually invalidate in software.
This adds code to do the invalidate. It keys off a device tree property
to say where the to do the MMIO for the invalidate and some information
on what the format of the invalidate including some magic routing info.
it_busno get overloaded with this magic routing info and it_index with
the MMIO address for the invalidate command.
This then gets hooked into the building and freeing of TCEs.
This is only useful on bare metal pseries. pHyp takes care of this when
virtualised.
Based on patch from Milton with cleanups from Mikey.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 23 Nov 2011 20:07:22 +0000 (20:07 +0000)]
powerpc/time: Optimise decrementer_check_overflow
decrementer_check_overflow is called from arch_local_irq_restore so
we want to make it as light weight as possible. As such, turn
decrementer_check_overflow into an inline function.
To avoid a circular mess of includes, separate out the two components
of struct decrementer_clock and keep the struct clock_event_device
part local to time.c.
The fast path improves from:
arch_local_irq_restore
0: mflr r0
4: std r0,16(r1)
8: stdu r1,-112(r1)
c: stb r3,578(r13)
10: cmpdi cr7,r3,0
14: beq- cr7,24 <.arch_local_irq_restore+0x24>
...
24: addi r1,r1,112
28: ld r0,16(r1)
2c: mtlr r0
30: blr
to:
arch_local_irq_restore
0: std r30,-16(r1)
4: ld r30,0(r2)
8: stb r3,578(r13)
c: cmpdi cr7,r3,0
10: beq- cr7,6c <.arch_local_irq_restore+0x6c>
...
6c: ld r30,-16(r1)
70: blr
Unfortunately we still setup a local TOC (due to -mminimal-toc). Yet
another sign we should be moving to -mcmodel=medium.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 23 Nov 2011 20:07:21 +0000 (20:07 +0000)]
powerpc/time: Fix some style issues
Fix some formatting issues and use the DECREMENTER_MAX
define instead of 0x7fffffff.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 23 Nov 2011 20:07:20 +0000 (20:07 +0000)]
powerpc/time: Remove unnecessary sanity check of decrementer expiration
The clockevents code uses max_delta_ns to avoid calling a
clockevent with too large a value.
Remove the redundant version of this in the timer_interrupt
code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 23 Nov 2011 20:07:19 +0000 (20:07 +0000)]
powerpc/time: Use clocksource_register_hz
Use clocksource_register_hz which calculates the shift/mult
factors for us. Also remove the shift = 22 assumption in
vsyscall_update - thanks to Paul Mackerras and John Stultz for
catching that.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 23 Nov 2011 20:07:18 +0000 (20:07 +0000)]
powerpc/time: Use clockevents_calc_mult_shift
We can use clockevents_calc_mult_shift instead of doing all
the work ourselves.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 23 Nov 2011 20:07:17 +0000 (20:07 +0000)]
powerpc/time: Handle wrapping of decrementer
When re-enabling interrupts we have code to handle edge sensitive
decrementers by resetting the decrementer to 1 whenever it is negative.
If interrupts were disabled long enough that the decrementer wrapped to
positive we do nothing. This means interrupts can be delayed for a long
time until it finally goes negative again.
While we hope interrupts are never be disabled long enough for the
decrementer to go positive, we have a very good test team that can
drive any kernel into the ground. The softlockup data we get back
from these fails could be seconds in the future, completely missing
the cause of the lockup.
We already keep track of the timebase of the next event so use that
to work out if we should trigger a decrementer exception.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Chuck Meade [Fri, 18 Jun 2010 13:22:26 +0000 (09:22 -0400)]
drivers/serial/ucc_uart.c: Add missing call to init UCC UART port timeout
The UCC UART driver is missing a call to uart_update_timeout().
Without this call, attempting to close the port after outputting large
amounts of data (i.e. using tty and uart buffering) results in long
timeouts before the port will actually be shut down.
For example, cat a large file to a UCC UART port. With the current
driver, the port will stay open for 30 seconds after the last byte
of data is output. But with this patch, the port is closed as
expected, just after the data has been output (tx fifos empty).
Signed-off-by: Chuck Meade <chuck@ThePTRGroup.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Mon, 31 Oct 2011 22:06:35 +0000 (17:06 -0500)]
powerpc/fsl_msi: add support for the fsl, msi property in PCI nodes
On Freescale parts with multiple MSI controllers, the controllers are
combined into one "pool" of interrupts. Whenever a device requests an MSI
interrupt, the next available interrupt from the pool is selected,
regardless of which MSI controller the interrupt is from. This works
because each PCI bus has an ATMU to all of CCSR, so any PCI device can
access any MSI interrupt register.
The fsl,msi property is used to specify that a given PCI bus should only
use a specific MSI device. This is necessary, for example, with the
Freescale hypervisor, because the MSI devices are assigned to specific
partitions.
Ideally, we'd like to be able to assign MSI devices to PCI busses within
the MSI or PCI layers. However, there does not appear to be a mechanism
to do that. Whenever the MSI layer wants to allocate an MSI interrupt to
a PCI device, it just calls arch_setup_msi_irqs(). It would be nice if we
could register an MSI device with a specific PCI bus.
So instead we remember the phandles of each MSI device, and we use that to
limit our search for an available interrupt. Whenever we are asked to
allocate a new interrupt for a PCI device, we check the fsl,msi property
of the PCI bus for that device. If it exists, then as we are looping over
all MSI devices, we skip the ones that don't have a matching phandle.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 24 Nov 2011 07:07:08 +0000 (01:07 -0600)]
powerpc/85xx: Renamed mpc85xx_common.c to common.c
The file name is already scoped by the directory its in.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 24 Nov 2011 07:00:10 +0000 (01:00 -0600)]
powerpc/85xx: Additional consolidate of_platform_bus_probe calls
P1010RDB & P1023RDS can use the new mpc85xx_common_publish_devices().
Also move 'fsl,srio' into the list of standard buses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Dmitry Eremin-Solenikov [Thu, 17 Nov 2011 17:56:17 +0000 (21:56 +0400)]
powerpc/85xx: consolidate of_platform_bus_probe calls
85xx board files have a lot of duplication in *_publish_devices()/
*_declare_of_platform_devices() functions. Merge that into a single
function common to most of the boards.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Dmitry Eremin-Solenikov [Thu, 17 Nov 2011 17:56:16 +0000 (21:56 +0400)]
powerpc/85xx: separate cpm2 pic init
Separate handling of CPM2 PIC initialization to mpc85xx_cpm2_pic_init()
function.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Dmitry Eremin-Solenikov [Thu, 17 Nov 2011 14:48:50 +0000 (18:48 +0400)]
powerpc/83xx: make mpc830x_rdb use mpc83xx_setup_pci
Traditionally mpc830x_rdb board file searched for mpc8308-pcie devices.
However both in-kernel dts from the beginning declared those pcie units
as compatible with mpc8314-pci, which is handled by mpc83xx_setup_pci().
Drop special handling for mpc8308 and use common function instead.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Dmitry Eremin-Solenikov [Thu, 17 Nov 2011 14:48:48 +0000 (18:48 +0400)]
powerpc/83xx: merge PCI bridge additions
Nearly all mpc83xx-based boards have a common piece of code - one that
loops over all pci/pcie bridges and registers them. Merge that code into
a special function common to all boards.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Dmitry Eremin-Solenikov [Thu, 17 Nov 2011 14:48:47 +0000 (18:48 +0400)]
powerpc/83xx: consolidate of_platform_bus_probe calls
83xx board files have a lot of duplication in
*_declare_of_platform_devices() functions. Merge that into a single
function common to most of the boards.
The only leftover is mpc834x_itx.c board file which explicitly asks for
fsl,pq2pro-localbus, as corresponding bindings don't provide
"simple-bus" compatibility in localbus node.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Dmitry Eremin-Solenikov [Fri, 22 Jul 2011 19:55:42 +0000 (23:55 +0400)]
powerpc/83xx: consolidate init_IRQ functions
On mpc83xx platform nearly all _init_IRQ functions look alike. They either
just setup ipic, or setup ipic and QE PIC. Separate this to special functions
to be either referenced from ppc_md, or called from board file.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Fri, 18 Nov 2011 17:50:00 +0000 (11:50 -0600)]
powerpc/85xx: add pixis indirect mode device tree node
The Freescale P1022 has a unique pin muxing "feature" where the DIU video
controller's video signals are muxed with 24 of the local bus address signals.
When the DIU is enabled, the bulk of the local bus is disabled, preventing
access to memory-mapped devices like NOR flash and the pixis FPGA.
In this situation, the pixis supports "indirect mode", which allows access
to the pixis itself by reading/writing addresses on specific local bus
chip selects. CS0 is used to select which pixis register to access, and
CS1 is used to read/write the value.
To support this, we introduce another board-control child node of the
localbus node that contains a 'reg' property for CS0 and CS1. This will
produce the correct physical addresses for CS0 and CS1.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Jia Hongtao [Mon, 21 Nov 2011 06:29:11 +0000 (14:29 +0800)]
powerpc/85xx: Add lbc suspend support for PM
Power supply for LBC registers is off when system go to deep-sleep state.
We save the values of registers before suspend and restore to registers
after resume.
We removed the last two reservation arrays from struct fsl_lbc_regs for
allocating less memory and minimizing the memcpy size.
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Jason Jin [Fri, 28 Oct 2011 08:08:00 +0000 (16:08 +0800)]
powerpc/fsl-pci: Don't hide resource for pci/e when configured as Agent/EP
Current pci/pcie init code will hide the pci/pcie host resource.
But did not judge it is host/RC or agent/EP. If configured as
agent/EP, we should avoid hiding its resource in the host side.
In PCI system, the Programing Interface can be used to judge the
host/agent status:
Programing Interface = 0: host
Programing Interface = 1: Agent
In PCIE system, both the Programing Interface and Header type can
be used to judge the RC/EP status.
Header Type = 0: EP
Header Type = 1: RC
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 17 Nov 2011 14:01:40 +0000 (08:01 -0600)]
powerpc/85xx: Update SRIO device tree nodes
Update all dts files that support SRIO controllers to match the new
fsl,srio device tree binding.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Mon, 7 Nov 2011 16:22:36 +0000 (10:22 -0600)]
powerpc/85xx: Rework P5020DS device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p5020-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 4 Nov 2011 14:47:49 +0000 (09:47 -0500)]
powerpc/85xx: Rework P4080DS device trees
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p4080-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 9 Nov 2011 19:21:57 +0000 (13:21 -0600)]
powerpc/85xx: Rework P3060QDS device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p3060-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level
* Fixed l3-cache IRQs, we have 2 CPCs, so we should have IRQs for both
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Mon, 7 Nov 2011 16:38:56 +0000 (10:38 -0600)]
powerpc/85xx: Rework P3041DS device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p3041-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Fixed some dcsr compatiable typo's from 'p43041' to 'p3041'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Mon, 7 Nov 2011 16:58:28 +0000 (10:58 -0600)]
powerpc/85xx: Rework P2041RDB device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p2041-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 4 Nov 2011 05:48:57 +0000 (00:48 -0500)]
powerpc/85xx: Rework P2020RDB device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
moved PCI device IRQs down to virtual bridge level
* Updated spi node to new espi binding specification
* Renamed 'sdhci' node to 'sdhc'
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Fixed wrong reg offsets for mdio nodes associated with etsec2 &
* etsec3
* Dropping "fsl,p2020-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 26 Oct 2011 13:35:24 +0000 (08:35 -0500)]
powerpc/85xx: Rework P2020DS device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Updated spi node to new espi binding specification
* Renamed 'sdhci' node to 'sdhc'
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Fixed wrong reg offsets for mdio nodes associated with etsec2 & etsec3
* Dropping "fsl,p2020-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 9 Nov 2011 20:53:33 +0000 (14:53 -0600)]
powerpc/85xx: Rework P1023RDS device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Dropping "fsl,p1023-IP..." from compatibles for standard blocks
* Removed incorrect power/pmc node, there are no etsec on P1023
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 26 Oct 2011 06:01:54 +0000 (01:01 -0500)]
powerpc/85xx: Rework P1022DS device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Updated spi node to new espi binding specification
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Added usb node for 2nd usb controller
* Dropping "fsl,p1022-IP..." from compatibles for standard blocks
* Fixed bug in local bus range node for CS2, was maping to
0x0 0x0xffa00000 instead of 0xf 0xffa00000
* Fixed localbus reg property should have been 0xf 0xffe05000
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Tested-by: Timur Tabi <timur@freescale.com>
Kumar Gala [Wed, 2 Nov 2011 15:15:30 +0000 (10:15 -0500)]
powerpc/85xx: Rework P1021MDS device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
moved PCI device IRQs down to virtual bridge level
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Added usb node for 2nd usb controller
* Dropping "fsl,p1021-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 21 Oct 2011 04:46:12 +0000 (23:46 -0500)]
powerpc/85xx: Add P1020RDB 36-bit address map device tree
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 20 Oct 2011 07:21:09 +0000 (02:21 -0500)]
powerpc/85xx: Rework P1020RDB device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Dropping "fsl,p1020-IP..." from compatibles for standard blocks
* Fixed PCIe interrupt-maps to have proper number of cells
* Added mdio node for etsec@26000
* Added usb node for 2nd usb controller
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 26 Oct 2011 05:10:58 +0000 (00:10 -0500)]
powerpc/85xx: Add a P1010RDB 36-bit address map device tree
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>