rtlwifi: Add btcoex record_pwr_mode

Add btcoex record pwr mode to control LPS's parameters and share time
with BT.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: Revise special packet notification to be readable format.

We extend types of special packets to a enumeration from boolean value.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: Add TX report and disable key to force wait until report acked.

When using EAPOL to do a PTK rekey, there is a possible race condition.
When msg 3/4 is received, the supplicant will send msg 4/4 and install
the new key immediately; however, the driver must make sure that msg 4/4
is sent before installing the new key. We use TX report to ensure it is
sent.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: extend debug_comp to u64

The number of debugging conditions now exceeds the capabilities of a
32-bit word.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: Correct power save capability while init mac80211

Since the driver itself will enter power saving mode dynamically
according to the traffic, we set hw capability SUPPORTS_PS and
SUPPORTS_DYNAMIC_PS in case of fwctrl_lps.

The process IEEE80211_CONF_CHANGE_PS in op_config is used by
SW-LPS only, so we add constraints to avoid errors.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: vincent_fann <vincent_fann@realtek.com>
Signed-off-by: shaofu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: btcoex: rtl8723be: fix ant_sel not work

To make ant_sel work, we should call power_on_setting to set antenna
correctly.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: btcoex: set correct interface type and parameter.

This commit fixies two problems. The first one is interface types
(e.g. PCI) that are used to switch antenna, and the second is to add
wifi_only parameter to give correct state.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: btcoex: call bind to setup btcoex

New btcoex add a function 'bind' to connect adapter, so we should call
it during initializing.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: add tx frame for common device configuration

After successful loading of firmware, a CARD READY indication is
received by host. Common device configuration parameters are sent
to the device after this. It includes information like device
operating mode (Wi-Fi alone or BT coex), power save related
parameters, GPIO information etc. As device supports BT coex,
this frame is send in COEX queue initially. Based on the operating
mode, CARD READY indication is received from each protocol module
in firmware i.e. WLAN, BT.

Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: configure new boot parameters to device

Boot parameters are changed in new firmware. Also three
new sdio sleep parameters are added for ultra low power
save.

Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: receive path enhancement for RS9113

RS9113 chipset supports Coex feature. Initial frame exchanges during
device initialization happens on coex queue. This patch adds the
handling for coex queue.

Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: Register interrupt handler before firmware load

Before firmware load, sometimes false interrupts are received.
System hang is observed if interrupt handler is not registered
to receive these interrupts. Hence interrupt handler registration
is moved before firmware load. We will drop these false interrupts
as these are not from the device.

Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: use enum for FSM states

Currently macros are used for FSM states. We will replace
it with enum so that new state can be added easily without
worrying about macro value.

Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: add usb RS9113 chipset support

usb device id and vendor id for RS9113 chipset are included.
So it can be used through usb interface.

Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: debugfs: remove redunant check of mwifiex_dfs_dir

debugfs_remove already check mwifiex_dfs_dir, so remove it.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: fixes the unexpected be printed log by default

This patch uses WARN level is not printed by default.

In some cases, some boards have always met the unused log be printed as
follows.
...
[23193.523182] mwifiex_pcie 0000:01:00.0: mwifiex_get_cfp:
cannot find cfp by band 2    & channel=13 freq=0
[23378.633684] mwifiex_pcie 0000:01:00.0: mwifiex_get_cfp:
cannot find cfp by band 2    & channel=13 freq=0

Due to we used the wifi default area was US and didn't support 12~14
channels. As Frequencies:
* 2412 MHz [1] (30.0 dBm)
* 2417 MHz [2] (30.0 dBm)
* 2422 MHz [3] (30.0 dBm)
* 2427 MHz [4] (30.0 dBm)
* 2432 MHz [5] (30.0 dBm)
* 2437 MHz [6] (30.0 dBm)
* 2442 MHz [7] (30.0 dBm)
* 2447 MHz [8] (30.0 dBm)
* 2452 MHz [9] (30.0 dBm)
* 2457 MHz [10] (30.0 dBm)
* 2462 MHz [11] (30.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)

Also, as the commit 1b499cb72f26b
("mwifiex: disable channel filtering feature in firmware"), it proved to
be a feature to get better scan result from overlapping channel.

Even there could be AP from overlapping channel (might be 12/13/14
in this case), it will be filtered depend on reg domain rules.
e.g:
...
if (ch->flags & IEEE80211_CHAN_DISABLED)
        continue;

So it should not been an ERROR, use the WARN level to instead it for now.

Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: fix REG_USTIME_TSF register definition

The REG_USTIME_TSF (US Time Tuning for TSF) definition of Realtek chips
should be 0x55C.

Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Use separate firmware for revision 0 of the brcm43430 chip

The brcm43430 chip needs different firmware files for chip revision 0
and 1. The file currently in linux-firmware is for revision 1 only.

This commit makes brcmfmac request brcmfmac43430a0-sdio.bin instead
of brcmfmac43430-sdio.bin for revision 0 chips.

Note that the behavior for revision 1 chips is not changed, ideally those
would load brcmfmac43430a1-sdio.bin, but that will break existing setups.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wlcore: spi: remove unnecessary variable

Remove unnecessary variable and refactor the code.

Addresses-Coverity-ID: 1365000
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wlcore: add wl1285 compatible

Motorola Droid 4 uses a WL 1285C. With differences between
chips not being public let's add explicit binding for wl1285
instead of relying on wl1283 being very similar.

Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: Replace semaphore async_sem with mutex

The semaphore 'async_sem' is used as a simple mutex, so
it should be written as one. Semaphores are going away in the future.

Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: btcoex: let btcoex get wifi rssi and link status

Instead of rssi status, the btcoex also needs to get the link status of
the wifi. In addition, some of the rssi status can be merged into link
status.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: btcoex: remove unused display functions

These display functions are useless and will not be called in the
future.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: btcoex: bind BT coex information with wifi driver

When initializing, gather BT information in struct btcoexist and
provide them to wifi driver.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: btcoex: hook external functions for newer chips

Hook the external functions for newer ICs such as 8821a and 8192e.

Rename ex_halbtc8192e2ant_halt_notify to ex_btc8192e2ant_halt_notify.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: btcoex: add settings before the hardware is ready

When the hardware is turned on and in the initialization stage, the PTA
circuit is unstable. Hence we need to force some hardware settings to
make sure the PTA circuit work correctly, otherwise it may affect the
user's experience.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: btcoex: hook external PnP notify by chip for wifi driver

Hook the chip-specific PnP notify functions for the wifi driver to
notify btcoexistence.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: btcoex: settings before firmware is downloaded

The btcoex is sometimes unstable because there are some unexpected
behaviors before the firmware has been downloaded successfully.

Therefore we force the antenna path settings to avoid this, then let the
firmware control the btcoexistence when the firmware is ready.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: btcoex: rename ex_halbtc*ant to ex_btc*ant

These external functions are for BT-coexistence, so remove the "hal"
prefix for consistancy.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: btcoex: add macros to check chip type

For some external functions that have hardware dependency, we need to
know the type of the hardware before invoking them.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

qtnfmac: check band before allocating cmd_skb to avoid resource leak

The current code allocates cmd_skb and then will leak this if band->band
is an illegal value. It is simpler to sanity check the band first before
allocating cmd_skb so that we don't have to free cmd_skb if an invalid
band occurs.

Detected by CoverityScan, CID#1437561 ("Resource Leak")

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: make function mwifiex_ret_pkt_aggr_ctrl static

function mwifiex_ret_pkt_aggr_ctrl can be made static as it does not
need to be in global scope.

Cleans up sparse warning: "symbol 'mwifiex_ret_pkt_aggr_ctrl' was not
declared. Should it be static?"

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Fix glom_skb leak in brcmf_sdiod_recv_chain

An earlier change to this function (3bdae810721b) fixed a leak in the
case of an unsuccessful call to brcmf_sdiod_buffrw(). However, the
glom_skb buffer, used for emulating a scattering read, is never used
or referenced after its contents are copied into the destination
buffers, and therefore always needs to be freed by the end of the
function.

Fixes: 3bdae810721b ("brcmfmac: Fix glob_skb leak in brcmf_sdiod_recv_chain")
Fixes: a413e39a38573 ("brcmfmac: fix brcmf_sdcard_recv_chain() for host without sg support")
Cc: stable@vger.kernel.org # 4.9.x-
Signed-off-by: Peter S. Housel <housel@acm.org>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Fix grammar issue in error message

Fix grammar issue in error message about ISO3166.

Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: add scheduled scan support for specified BSSIDs

Add support to handle scheduled scan request containing BSSID in
the matchsets. The firmware can send event upon finding BSSIDs and
SSIDs. To get these in one event the bit REPORT_SEPARATELY needed
to be removed from the flags in brcmf_pno_config().

Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: add mutex to protect pno requests

The request references kept in pno are accessed in user-space context
and in firmware event handler context. As such we need to protect it
with a lock. As both context allow sleep a mutex seems appropriate.

Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: add support multi-scheduled scan

This change adds support for multi-scheduled scan in the driver. It
currently relies on g-scan support in firmware and will set struct
wiphy::max_sched_scan_reqs accordingly. This is limited to 16 concurrent
requests.

The firmware currently has a limit of 64 channels that can be configured
for all requests in total regardless whether there are duplicates. So if
a request uses 35 channels there are 29 channels left for another request.
When user-space does not specify any channels cfg80211 will add all
channels defined by the wiphy instance to the request, which makes
reaching the limit rather easy for dual-band devices.

Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2017-06-06' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next

First batch of iwlwifi driver patches 4.13

* Loads of FW API documentation improvements (for tools and htmldoc);
* Continued work for the new A000 family;
* Bumped the maximum supported FW API to 31;
* Improve the differentiation between 8000, 9000 and A000 families;
* A lot of fixes and cleanups here and there;

kvalo: There were conflicts iwl_mvm_stop_device() and
iwl_mvm_tcool_set_cur_state(). The former was easy but latter needed more
thought. Apparently the mutex was taken too late, so I fixed so that the mutex
is taken first and then check for iwl_mvm_firmware_running().

Merge tag 'wireless-drivers-next-for-davem-2017-06-12' of git://git./linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 4.13

The first pull request for 4.13. We have a new driver qtnfmac, but
also rsi driver got a support for new firmware and supporting ath10k
SDIO devices was started.

Major changes:

ath10k

* add initial SDIO support (still work in progress)

rsi

* new loading for the new firmware version

rtlwifi

* final patches for the new btcoex support

rt2x00

* add device ID for Epson WN7512BEP

qtnfmac

* new driver for Quantenna QSR10G chipsets
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'udp-reduce-cache-pressure'

Paolo Abeni says:

====================
udp: reduce cache pressure

In the most common use case, many skb fields are not used by recvmsg(), and
the few ones actually accessed lays on cold cachelines, which leads to several
cache miss per packet.

This patch series attempts to reduce such misses with different strategies:
* caching the interesting fields in the scratched space
* avoid accessing at all uninteresting fields
* prefetching

Tested using the udp_sink program by Jesper[1] as the receiver, an h/w l4 rx
hash on the ingress nic, so that the number of ingress nic rx queues hit by the
udp traffic could be controlled via ethtool -L.

The udp_sink program was bound to the first idle cpu, to get more
stable numbers.

On a single numa node receiver:

nic rx queues           vanilla                 patched kernel      delta
1                       1850 kpps               1850 kpps           0%
2                       2370 kpps               2700 kpps           13.9%
16                      2000 kpps               2220 kpps           11%

[1] https://github.com/netoptimizer/network-testing/blob/master/src/udp_sink.c

v1 -> v2:
  - replaced secpath_reset() with skb_release_head_state()
  - changed udp_dev_scratch fields types to u{32,16} variant,
    replaced bitfield with bool

v2 -> v3:
  - no changes, tested against apachebench for performances regression
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

udp: try to avoid 2 cache miss on dequeue

when udp_recvmsg() is executed, on x86_64 and other archs, most skb
fields are on cold cachelines.
If the skb are linear and the kernel don't need to compute the udp
csum, only a handful of skb fields are required by udp_recvmsg().
Since we already use skb->dev_scratch to cache hot data, and
there are 32 bits unused on 64 bit archs, use such field to cache
as much data as we can, and try to prefetch on dequeue the relevant
fields that are left out.

This can save up to 2 cache miss per packet.

v1 -> v2:
  - changed udp_dev_scratch fields types to u{32,16} variant,
    replaced bitfiled with bool

Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

udp: avoid a cache miss on dequeue

Since UDP no more uses sk->destructor, we can clear completely
the skb head state before enqueuing. Amend and use
skb_release_head_state() for that.

All head states share a single cacheline, which is not
normally used/accesses on dequeue. We can avoid entirely accessing
such cacheline implementing and using in the UDP code a specialized
skb free helper which ignores the skb head state.

This saves a cacheline miss at skb deallocation time.

v1 -> v2:
  replaced secpath_reset() with skb_release_head_state()

Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: factor out a helper to decrement the skb refcount

The same code is replicated in 3 different places; move it to a
common helper.

Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sh_eth: add support for changing MTU

The hardware supports the MTU to be changed and the driver it self is
somewhat prepared to support this. This patch hooks up the callbacks to
be able to change the MTU from user-space.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf, arm64: take advantage of stack_depth tracking

Make use of recently implemented stack_depth tracking for arm64 JIT,
so that stack usage can be reduced heavily for programs not using
tail calls at least.

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mlx5-updates-2017-06-11' of git://git./linux/kernel/git/saeed/linux

Saeed Mahameed says:

====================
mlx5-updates-2017-06-11

This series provides updates to mlx5 header rewrite feature, from Or Gerlitz.
and three more small updates From maor and eran.

-------
Or says:

Packets belonging to flows which are different by matching may still need
to go through the same header re-writes (e.g set the current routing hop
MACs and issue TTL decrement).  To minimize the number of modify header
IDs, we add a cache for header re-write IDs which is keyed by the binary
chain of modify header actions.

The caching is supported for both eswitch and NIC use-cases, where the
actual conversion of the code to use caching comes in separate patches,
one per use-case.

Using a per field mask field, the TC pedit action supports modifying
partial fields. The last patch enables offloading that.
-------

From Maor, update flow table commands layout to the latest HW spec.
From Eran, ethtool connector type reporting updates.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: ti: cpdma: do not enable host error misc irq

CPSW driver does not handle this interrupt, so there are no reasons to enable
it in hardware.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: ti: cpsw: enable HWTSTAMP_FILTER_PTP_V1_L4_EVENT filter

CPSW driver supports PTP v1 messages, but for unknown reasons this filter
is not advertised. As result,
./tools/testing/selftests/networking/timestamping/timestamping utility
can't be used for testing of CPSW RX timestamping with option
SOF_TIMESTAMPING_RX_HARDWARE, because it uses
HWTSTAMP_FILTER_PTP_V1_L4_SYNC filter.

Hence, fix it by advertising HWTSTAMP_FILTER_PTP_V1_L4_XXX filters
in CPSW driver.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'bpf-misc-updates'

Daniel Borkmann says:

====================
Misc BPF updates

This set contains a couple of misc updates: stack usage reduction
for perf_sample_data in tracing progs, reduction of stale data in
verifier on register state transitions that I still had in my queue
and few selftest improvements as well as bpf_set_hash() helper for
tc programs.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: add bpf_set_hash helper for tc progs

Allow for tc BPF programs to set a skb->hash, apart from clearing
and triggering a recalc that we have right now. It allows for BPF
to implement a custom hashing routine for skb_get_hash().

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: remove cg_skb_func_proto and use sk_filter_func_proto directly

Since cg_skb_func_proto() doesn't do anything else than just calling
into sk_filter_func_proto(), remove it and set sk_filter_func_proto()
directly for .get_func_proto callback.

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf, tests: set rlimit also for test_align, so it doesn't fail

When running all the tests, through 'make run_tests', I had
test_align failing due to insufficient rlimit. Set it the same
way as all other test cases from BPF selftests do, so that
test case properly loads everything.

  [...]
  Summary: 7 PASSED, 1 FAILED
  selftests: test_progs [PASS]
  /home/foo/net-next/tools/testing/selftests/bpf
  Test   0: mov ... Failed to load program.
  FAIL
  Test   1: shift ... Failed to load program.
  FAIL
  Test   2: addsub ... Failed to load program.
  FAIL
  Test   3: mul ... Failed to load program.
  FAIL
  Test   4: unknown shift ... Failed to load program.
  FAIL
  Test   5: unknown mul ... Failed to load program.
  FAIL
  Test   6: packet const offset ... Failed to load program.
  FAIL
  Test   7: packet variable offset ... Failed to load program.
  FAIL
  Results: 0 pass 8 fail
  selftests: test_align [PASS]
  [...]

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf, tests: add a test for htab lookup + update traversal

Add a test case to track behaviour when traversing and updating the
htab map. We recently used such traversal, so it's quite useful to
keep it as an example in selftests.

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: reset id on spilled regs in clear_all_pkt_pointers

Right now, we don't reset the id of spilled registers in case of
clear_all_pkt_pointers(). Given pkt_pointers are highly likely to
contain an id, do so by reusing __mark_reg_unknown_value().

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: reset id on CONST_IMM transition

Whenever we set the register to the type CONST_IMM, we currently don't
reset the id to 0. id member is not used in CONST_IMM case, so don't
let it become stale, where pruning won't be able to match later on.

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: don't check spilled reg state for non-STACK_SPILLed type slots

spilled_regs[] state is only used for stack slots of type STACK_SPILL,
never for STACK_MISC. Right now, in states_equal(), even if we have
old and current stack state of type STACK_MISC, we compare spilled_regs[]
for that particular offset. Just skip these like we do everywhere else.

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: avoid excessive stack usage for perf_sample_data

perf_sample_data consumes 386 bytes on stack, reduce excessive stack
usage and move it to per cpu buffer. It's allowed due to preemption
being disabled for tracing, xdp and tc programs, thus at all times
only one program can run on a specific CPU and programs cannot run
from interrupt. We similarly also handle bpf_pt_regs.

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: Add a fec_enet_clear_ethtool_stats() stub for CONFIG_M5272

Commit 2b30842b23b9 ("net: fec: Clear and enable MIB counters on imx51")
introduced fec_enet_clear_ethtool_stats(), but missed to add a stub
for the CONFIG_M5272=y case, causing build failure for the
m5272c3_defconfig.

Add the missing empty stub to fix the build failure.

Fixes: Commit 2b30842b23b9 ("net: fec: Clear and enable MIB counters on imx51")
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the redundant skb->dev initialization in ip6_fragment

After moves the skb->dev and skb->protocol initialization into
ip6_output, setting the skb->dev inside ip6_fragment is unnecessary.

Fixes: 97a7a37a7b7b("ipv6: Initial skb->dev and skb->protocol in ip6_output")
Signed-off-by: Chenbo Feng <fengc@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: no need to check assoc id before calling sctp_assoc_set_id

sctp_assoc_set_id does the assoc id check in the beginning when
processing dupcookie, no need to do the same check before calling
it.

v1->v2:
  fix some typo errs Marcelo pointed in changelog.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: use read_lock_bh in sctp_eps_seq_show

This patch is to use read_lock_bh instead of local_bh_disable
and read_lock in sctp_eps_seq_show.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: fix recursive locking warning in sctp_do_peeloff

Dmitry got the following recursive locking report while running syzkaller
fuzzer, the Call Trace:
 __dump_stack lib/dump_stack.c:16 [inline]
 dump_stack+0x2ee/0x3ef lib/dump_stack.c:52
 print_deadlock_bug kernel/locking/lockdep.c:1729 [inline]
 check_deadlock kernel/locking/lockdep.c:1773 [inline]
 validate_chain kernel/locking/lockdep.c:2251 [inline]
 __lock_acquire+0xef2/0x3430 kernel/locking/lockdep.c:3340
 lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755
 lock_sock_nested+0xcb/0x120 net/core/sock.c:2536
 lock_sock include/net/sock.h:1460 [inline]
 sctp_close+0xcd/0x9d0 net/sctp/socket.c:1497
 inet_release+0xed/0x1c0 net/ipv4/af_inet.c:425
 inet6_release+0x50/0x70 net/ipv6/af_inet6.c:432
 sock_release+0x8d/0x1e0 net/socket.c:597
 __sock_create+0x38b/0x870 net/socket.c:1226
 sock_create+0x7f/0xa0 net/socket.c:1237
 sctp_do_peeloff+0x1a2/0x440 net/sctp/socket.c:4879
 sctp_getsockopt_peeloff net/sctp/socket.c:4914 [inline]
 sctp_getsockopt+0x111a/0x67e0 net/sctp/socket.c:6628
 sock_common_getsockopt+0x95/0xd0 net/core/sock.c:2690
 SYSC_getsockopt net/socket.c:1817 [inline]
 SyS_getsockopt+0x240/0x380 net/socket.c:1799
 entry_SYSCALL_64_fastpath+0x1f/0xc2

This warning is caused by the lock held by sctp_getsockopt() is on one
socket, while the other lock that sctp_close() is getting later is on
the newly created (which failed) socket during peeloff operation.

This patch is to avoid this warning by use lock_sock with subclass
SINGLE_DEPTH_NESTING as Wang Cong and Marcelo's suggestion.

Reported-by: Dmitry Vyukov <dvyukov@google.com>
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/packet: remove unneeded declaraion of tpacket_snd().

This patch removes unneeded forward declaration of tpacket_snd()
in net/packet/af_packet.c.

Signed-off-by: Rami Rosen <rami.rosen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: Remove duplicate tcp_filter hook in ipv6

There are two tcp_filter hooks in tcp_ipv6 ingress path currently.
One is at tcp_v6_rcv and another is in tcp_v6_do_rcv. It seems the
tcp_filter() call inside tcp_v6_do_rcv is redundent and some packet
will be filtered twice in this situation. This will cause trouble
when using eBPF filters to account traffic data.

Signed-off-by: Chenbo Feng <fengc@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: warn user when 802.3ad speed is unknown

Goal is to advertise the user when ethtool speeds and 802.3ad speeds are
desynchronized.
When this case happens, the kernel needs to be patched.

Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netns: fix error code when the nsid is already used

When the user tries to assign a specific nsid, idr_alloc() is called with
the range [nsid, nsid+1]. If this nsid is already used, idr_alloc() returns
ENOSPC (No space left on device). In our case, it's better to return
EEXIST to make it clear that the nsid is not available.

CC: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netns: define extack error msg for nsis cmds

It helps the user to identify errors.

CC: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4: fix memory leak in init_one()

Free up mbox_log allocated for PF0 to PF3.

Fixes: 7829451c695e ("cxgb4: Add control net_device for configuring PCIe VF")
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: add qed_int_sb_init() stub function

When CONFIG_QED_SRIOV is disabled, we get a build error:

drivers/net/ethernet/qlogic/qed/qed_int.c: In function 'qed_int_sb_init':
drivers/net/ethernet/qlogic/qed/qed_int.c:1499:4: error: implicit declaration of function 'qed_vf_set_sb_info'; did you mean 'qed_mcp_get_resc_info'? [-Werror=implicit-function-declaration]

All the other declarations have a 'static inline' stub as an alternative
here, so this adds one more for qed_int_sb_init.

Fixes: 50a207147fce ("qed: Hold a single array for SBs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'qed-Light-L2-updates'

Yuval Mintz says:

====================
qed*: Light L2 updates

This series does a major overhaul of the LL2 logic in qed.
The single biggest change done here is in #5 where we're changing
the API qed provides for LL2 [both internally in case of storage and
externally in case of RoCE] to become callback-based to allow cleaner
scalability in preperation to the future iWARP submission which would
aadd additional flavors of LL2. It's also the only patch in series
to modify !qed logic [qedr].

Patches prior to that mostly deal with refactoring LL2 code,
encapsulating varaious parameters into structure and re-ordering
of LL2 code. The latter patches add some small missing bits of LL2
ffunctionality.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

qed: collect GSI port statistics

The LL2 statistics already have place holders for these, but haven't
populated them so far.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: Call rx_release_cb() when flushing LL2

Driver to inform the connection owner that the its buffers are being
released as part of a flush.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: No need for LL2 frags indication

This is a legacy leftover; There's no current flow where 'frags_mapped'
would be set.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed*: LL2 callback operations

LL2 today is interrupt driven - when tx/rx completion arrives [or any
other indication], qed needs to operate on the connection and pass
the information to the protocol-driver [or internal qed consumer].
Since we have several flavors of ll2 employeed by the driver,
each handler needs to do an if-else to determine the right functionality
to use based on the connection type.

In order to make things more scalable [given that we're going to add
additional types of ll2 flavors] move the infrastrucutre into using
a callback-based approach - the callbacks would be provided as part
of the connection's initialization parameters.

Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: LL2 code relocations

Instead of having the OOO logic packetd, divide it with rest of code
according to establish/release flows.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: Cleaner seperation of LL2 inputs

A LL2 connection [qed_ll2_info] has a sub-structure of type qed_ll2_conn
that contain various inputs for ll2 acquisition, but the connection also
utilizes a couple of other inputs.

Restructure the input structure to include all the inputs and refactor
the code necessary to populate those.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: Revise ll2 Rx completion

This introduces qed_ll2_comp_rx_data as a public struct
and moves handling of Rx packets in LL2 into using it.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: LL2 to use packed information for tx

First step in revising the LL2 interface, this declares
qed_ll2_tx_pkt_info as part of the ll2 interface, and uses it for
transmission instead of receiving lots of parameters.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'r8152-minor-adjustment'

Hayes Wang says:

====================
r8152: minor adjustment

Adjust some code to make it reasonable or satisfy the suggestion from
the engineers.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

r8152: replace napi_complete with napi_complete_done

Change from using napi_complete to napi_complete_done to allow for the
use of gro_flush_timeout in tuning network processing.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8152: avoid rx queue more than 1000 packets

Stop queuing rx packets if it is more than 1000.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8152: check if disabling ALDPS is finished

Use PLA 0xe000 bit 8 to check if disabling ALDPS is finished.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8152: move the initialization to reset_resume function

Move tp->rtl_ops.init() from rtl8152_resume() to rtl8152_reset_resume().
The initialization is only necessary for reset_resume().

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8152: move the default coalesce setting for RTL8153

Only RTL8153 could set coalesce, so move the default setting for
rtl8152_probe() to r8153_init().

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8152: adjust U2P3 for RTL8153

Use another way to keep disabling the U2P3 for both RTL_VER_03 and
RTL_VER_04.

Move enabling U2P3 from r8153_init() to r8153_hw_phy_cfg(). The
engineer ask the setting should be done after PHY settings.

Disable U2P3 first in rtl8153_up().

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8152: adjust rtl8153_runtime_enable function

Adjust the order of rtl8153_runtime_enable() according to the
suggestion from the engineer.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8152: move the setting of rx aggregation

Move the setting from r8153_first_init() to r8153_init(). It only needs to
be set once.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8152: adjust the settings about MAC clock speed down for RTL8153

The MAC clock speed down could be enabled if the U1/U2 is disabled.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8152: adjust lpm settings for RTL8153

Enable lpm after r8153_init() and remove other enable/disable lpm.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8152: add r8153_phy_status function

Use r8153_phy_status() to check phy status of RTL8153.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: Fix test_obj_id.c for llvm 5.0

llvm 5.0 does not like the section name and the function name
to be the same:

clang -I. -I./include/uapi -I../../../include/uapi \
-I../../../../samples/bpf/ \
-Wno-compare-distinct-pointer-types \
-O2 -target bpf -c \
linux/tools/testing/selftests/bpf/test_obj_id.c -o \
linux/tools/testing/selftests/bpf/test_obj_id.o
fatal error: error in backend: 'test_prog_id' label emitted multiple times to
assembly file
clang-5.0: error: clang frontend command failed with exit code 70 (use -v to
see invocation)
clang version 5.0.0 (trunk 304326) (llvm/trunk 304329)

This patch makes changes to the section name and the function name.

Fixes: 95b9afd3987f ("bpf: Test for bpf ID")
Reported-by: Alexei Starovoitov <ast@fb.com>
Reported-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: Fix test_bpf_obj_id() when the bpf_jit_enable sysctl is diabled

test_bpf_obj_id() should not expect a non zero jited_prog_len
to be returned by bpf_obj_get_info_by_fd() when
net.core.bpf_jit_enable is 0.

The patch checks for net.core.bpf_jit_enable and
has different expectation on jited_prog_len.

This patch also removes the pwd.h header which I forgot
to remove after making changes.

Fixes: 95b9afd3987f ("bpf: Test for bpf ID")
Reported-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Initial skb->dev and skb->protocol in ip6_output

Move the initialization of skb->dev and skb->protocol from
ip6_finish_output2 to ip6_output. This can make the skb->dev and
skb->protocol information avalaible to the CGROUP eBPF filter.

Signed-off-by: Chenbo Feng <fengc@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4: handle interrupt raised when FW crashes

Handle TIMER0INT when FW crashes. Check for PCIE_FW[FW_EVAL]
and if it says "Device FW Crashed", then treat it as fatal.
Else, non-fatal.

Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'nfp-FW-app-build-name-reporting'

Jakub Kicinski says:

====================
nfp: FW app build name reporting

This series adds reporting FW build name in ethtool -i.  Most
of the patches are restructuring where information caching is
done.  There is also a minor error path fix.

These are last few patches finishing the basic nfp_app support.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

nfp: report application FW build name in ethtool -i

Make sure application FW build name is NULL-terminated and
print it as a part of ethtool's firmware version string.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nfp: keep MIP object around

Microcode Information Page contains some useful information, like
application firmware build name.  Keep it around, similar to RTSym
and HWInfo.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nfp: remove automatic caching of HWInfo

Make callers take care of managing life time of HWInfo.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nfp: remove automatic caching of RTsym table

The fact that RTsym table is cached inside nfp_cpp handle is
a relic of old times when nfpcore was a library module.  All
the nfp_cpp "caches" are awkward to deal with because of
concurrency and prone to keeping stale information.  Make
the run time symbol table be an object read out from the device
and managed by whoever requested it.  Since the driver loads
FW at ->probe() and never reloads, we can hold onto the table
for ever.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nfp: make sure to cancel port refresh on the error path

If very last stages of netdev registering and init fail some
other netdevs and devlink ports may have been visible to user
space before we torn them back down.  In this case there is a
slight chance user may have triggered port refresh.  We need
to make sure the async work is cancelled.

We have to cancel after releasing pf->lock, so we will always
try to cancel, regardless of which part of probe has failed.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>