Jorge Ramirez-Ortiz [Fri, 6 Sep 2019 20:54:11 +0000 (22:54 +0200)]
watchdog: qcom: remove unnecessary variable from private storage
there is no need to continue keeping the clock in private storage.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190906205411.31666-3-jorge.ramirez-ortiz@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Jorge Ramirez-Ortiz [Fri, 6 Sep 2019 20:54:10 +0000 (22:54 +0200)]
watchdog: qcom: support pre-timeout when the bark irq is available
Use the bark interrupt as the pre-timeout notifier whenever this
interrupt is available.
By default, the pretimeout notification shall occur one second earlier
than the timeout.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190906205411.31666-2-jorge.ramirez-ortiz@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Oliver Graute [Thu, 5 Sep 2019 14:36:49 +0000 (14:36 +0000)]
watchdog: imx_sc: this patch just fixes whitespaces
Fix only whitespace errors in imx_sc_wdt_probe()
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190905143644.20952-1-oliver.graute@kococonnector.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Ivan Mikhaylov [Wed, 28 Aug 2019 10:24:02 +0000 (13:24 +0300)]
watchdog: apseed: Add access_cs0 option for alt-boot
The option for the ast2400/2500 to get access to CS0 at runtime.
Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190828102402.13155-5-i.mikhaylov@yadro.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Ivan Mikhaylov [Wed, 28 Aug 2019 10:24:01 +0000 (13:24 +0300)]
watchdog: aspeed: add support for dual boot
Set WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION into WDT_CLEAR_TIMEOUT_STATUS
to clear out boot code source and re-enable access to the primary SPI flash
chip while booted via wdt2 from the alternate chip.
AST2400 datasheet says:
"In the 2nd flash booting mode, all the address mapping to CS0# would be
re-directed to CS1#. And CS0# is not accessible under this mode. To access
CS0#, firmware should clear the 2nd boot mode register in the WDT2 status
register WDT30.bit[1]."
Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190828102402.13155-4-i.mikhaylov@yadro.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Chris Packham [Thu, 29 Aug 2019 21:52:24 +0000 (09:52 +1200)]
watchdog: orion_wdt: use timer1 as a pretimeout
The orion watchdog can either reset the CPU or generate an interrupt.
The interrupt would be useful for debugging as it provides panic()
output about the watchdog expiry, however if the interrupt is used the
watchdog can't reset the CPU in the event of being stuck in a loop with
interrupts disabled or if the CPU is prevented from accessing memory
(e.g. an unterminated DMA).
The Armada SoCs have spare timers that aren't currently used by the
Linux kernel. We can use timer1 to provide a pre-timeout ahead of the
watchdog timer and provide the possibility of gathering debug before the
reset triggers.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190829215224.27956-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Anson Huang [Wed, 28 Aug 2019 13:35:01 +0000 (09:35 -0400)]
watchdog: Add i.MX7ULP watchdog support
The i.MX7ULP Watchdog Timer (WDOG) module is an independent timer
that is available for system use.
It provides a safety feature to ensure that software is executing
as planned and that the CPU is not stuck in an infinite loop or
executing unintended code. If the WDOG module is not serviced
(refreshed) within a certain period, it resets the MCU.
Add driver support for i.MX7ULP watchdog.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1566999303-18795-2-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Anson Huang [Wed, 28 Aug 2019 13:35:00 +0000 (09:35 -0400)]
dt-bindings: watchdog: Add i.MX7ULP bindings
Add the watchdog bindings for Freescale i.MX7ULP.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <rohb@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1566999303-18795-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Maxime Ripard [Wed, 21 Aug 2019 14:38:33 +0000 (16:38 +0200)]
dt-bindings: watchdog: sun4i: Add the watchdog clock
The Allwinner watchdog has a clock that has been described in some DT, but
not all of them.
The binding is also completely missing that description. Let's add that
property to be consistent.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190821143835.7294-4-mripard@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Maxime Ripard [Wed, 21 Aug 2019 14:38:32 +0000 (16:38 +0200)]
dt-bindings: watchdog: sun4i: Add the watchdog interrupts
The Allwinner watchdog has an interrupt, either shared or dedicated
depending on the SoC, that has been described in some DT, but not all of
them.
The binding is also completely missing that description. Let's add that
property to be consistent.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190821143835.7294-3-mripard@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Maxime Ripard [Wed, 21 Aug 2019 14:38:31 +0000 (16:38 +0200)]
dt-bindings: watchdog: Convert Allwinner watchdog to a schema
The Allwinner SoCs have a watchdog supported in Linux, with a matching
Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190821143835.7294-2-mripard@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Maxime Ripard [Mon, 19 Aug 2019 18:20:34 +0000 (20:20 +0200)]
dt-bindings: watchdog: Add YAML schemas for the generic watchdog bindings
The watchdogs have a bunch of generic properties that are needed in a
device tree. Add a YAML schemas for those.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190821143835.7294-1-mripard@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Ryan Chen [Mon, 19 Aug 2019 05:17:38 +0000 (14:47 +0930)]
watchdog: aspeed: Add support for AST2600
The ast2600 can be supported by the same code as the ast2500.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190819051738.17370-3-joel@jms.id.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Joel Stanley [Mon, 19 Aug 2019 05:17:37 +0000 (14:47 +0930)]
dt-bindings: watchdog: Add ast2600 compatible
This adds a compatible for the ast2600, a new ASPEED SoC.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190819051738.17370-2-joel@jms.id.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:09:06 +0000 (13:09 -0700)]
watchdog: ziirave_wdt: Update checked I2C functionality mask
Update checked I2C functionality mask to reflect all of the SMBus
primitives used by this driver.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-23-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:09:05 +0000 (13:09 -0700)]
watchdog: ziirave_wdt: Drop ziirave_firm_write_block_data()
There's only one user of ziirave_firm_write_block_data(), so we may as
well inline it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-22-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:09:04 +0000 (13:09 -0700)]
watchdog: ziirave_wdt: Fix DOWNLOAD_START payload
Bootloader firmware expects the following traffic for DOWNLOAD_END:
S Addr Wr [A] 0x10 [A] P
using ziirave_firm_write_byte() will result in
S Addr Wr [A] 0x10 [A] 0x01 [A] 0x01 [A] P
which happens to work because firmware will ignore any extra bytes
sent. Fix this by converting the code to use i2c_smbus_write_byte()
instead.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-21-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:09:03 +0000 (13:09 -0700)]
watchdog: ziirave_wdt: Drop status polling code
Bootloader firmware doesn't implement DOWNLOAD_START or
DOWNLOAD_PACKET in a non-blocking way. It will stretch the clock of
the first status byte read until the operation is complete. Polling
for the status is not really necessary since it will always succed on
the first try. Replace polling code with a simple single byte read to
simplify things.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-20-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:09:02 +0000 (13:09 -0700)]
watchdog: ziirave_wdt: Fix RESET_PROCESSOR payload
Bootloader firmware expects the following traffic for
RESET_PROCESSOR:
S Addr Wr [A] 0x0b [A] 0x01 [A] P
using ziirave_firm_write_byte() will result in
S Addr Wr [A] 0x0b [A] 0x01 [A] 0x01 [A] P
which happens to work because firmware will ignore any extra bytes and
expected magic value matches byte count sent by
i2c_smbus_write_block_data(). Fix this by converting the code to use
i2c_smbus_write_byte_data() instead.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-19-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:09:01 +0000 (13:09 -0700)]
watchdog: ziirave_wdt: Fix DOWNLOAD_END payload
Bootloader firmware expects the following traffic for DOWNLOAD_END:
S Addr Wr [A] 0x11 [A] P
using ziirave_firm_write_byte() will result in
S Addr Wr [A] 0x11 [A] 0x01 [A] 0x01 [A] P
which happens to work because firmware will ignore any extra bytes
sent. Fix this by converting the code to use i2c_smbus_write_byte()
instead.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-18-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:09:00 +0000 (13:09 -0700)]
watchdog: ziirave_wdt: Fix JUMP_TO_BOOTLOADER payload
Bootloader firmware expects the following traffic for
JUMP_TO_BOOTLOADER:
S Addr Wr [A] 0x0c [A] 0x01 [A] P
using ziirave_firm_write_byte() will result in
S Addr Wr [A] 0x0c [A] 0x01 [A] 0x01 [A] P
which happens to work because firmware will ignore any extra bytes and
expected magic value matches byte count sent by
i2c_smbus_write_block_data(). Fix this by converting the code to use
i2c_smbus_write_byte_data() instead.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-17-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:08:59 +0000 (13:08 -0700)]
watchdog: ziirave_wdt: Fix misleading error message
Fix misleading error message in ziirave_wdt_init_duration(). Saying
"unable to set ..." implies that an attempt at communication with
watchdog device has taken palce and was not successful. In this case,
however, all it indicates is that no reset pulse duration was
specified either via kernel parameter or Device Tree. Re-phase the log
message to be more clear about benign nature of this event.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-16-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:08:58 +0000 (13:08 -0700)]
watchdog: ziirave_wdt: Don't try to program readonly flash
Bootloader code will ignore any attempts to write data to any flash
area outside of [ZIIRAVE_FIRM_FLASH_MEMORY_START;
ZIIRAVE_FIRM_FLASH_MEMORY_END]. Firmware update code already have an
appropriate check to skip those areas when validating updated
firmware. Firmware programming code, OTOH, does not and will
needlessly send no-op I2C traffic. Add an appropriate check to
__ziirave_firm_write_pkt() so as to save all of that wasted effort.
While at it, normalize all of the address handling code to use full
32-bit address in units of bytes and convert it to an appropriate
value only in places where that is necessary.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-15-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:08:57 +0000 (13:08 -0700)]
watchdog: ziirave_wdt: Don't read out more than 'len' firmware bytes
We only compare first 'len' bytes of read firmware, so we don't need
to read more that that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-14-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:08:56 +0000 (13:08 -0700)]
watchdog: ziirave_wdt: Don't check if ihex record length is zero
Ihex_next_binrec() will return NULL if next record's 'len' is zero, so
explicit checks for that in the driver are unnecessary. Drop them.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-13-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:08:55 +0000 (13:08 -0700)]
watchdog: ziirave_wdt: Make use of put_unaligned_le16
Instead of doing this explicitly use put_unaligned_le16() to place
16-bit address value into command payload.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-12-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:08:54 +0000 (13:08 -0700)]
watchdog: ziirave_wdt: Zero out only what's necessary
Instead of zeroing out all of the packet and then overwriting a
significant portion of those zeros via memcpy(), zero out only a
portion of the packet that is known to not contain any data.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-11-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:08:53 +0000 (13:08 -0700)]
watchdog: ziirave_wdt: Fix incorrect use of ARRAY_SIZE
Both memset() and ziirave_firm_write_block_data() expect length in
bytes as an argument, not a number of elements in array. It just
happens that in this particular case both values are equal. Modify the
code to use sizeof() instead.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-10-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:08:52 +0000 (13:08 -0700)]
watchdog: ziirave_wdt: Skip zeros when calculating checksum
Zeros don't contribute anything to checksum value, so we can skip
unused portion of the packet when calculating its checksum.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-9-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:08:51 +0000 (13:08 -0700)]
watchdog: ziirave_wdt: Check packet length only once
We don't need to check for packet length more than once, so drop the
extra check in ziirave_firm_upload(). While at it move the check at
the very start of __ziirave_firm_write_pkt(), as to not waste any time
preparing a packet we'll never use.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-8-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:08:50 +0000 (13:08 -0700)]
watchdog: ziirave_wdt: Simplify ziirave_firm_write_pkt()
There no reason why ziirave_firm_write_pkt() has to take firmware
data via 'struct ihex_binrec' and it can just take address, data pointer
and data length as individual arguments. Make this change to allow us
to drastically simplify handling page crossing case by removing all of
the extra code required to split 'struct ihex_binrec' into two.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-7-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:08:49 +0000 (13:08 -0700)]
watchdog: ziirave_wdt: Log bootloader/firmware info during probe
Log bootloader/firmware info during probe. This information is
available via sysfs already, but it's really helpful to have this in
kernel log during startup as well.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-6-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:08:48 +0000 (13:08 -0700)]
watchdog: ziirave_wdt: Don't bail out on unexpected timeout value
Reprogramming bootloader on watchdog MCU will result in reported
default timeout value of "0". That in turn will be unnecessarily
rejected by the driver as invalid device (-ENODEV). Simplify probe to
read stored timeout value, set it to a sane default if it is bogus,
and then program that value unconditionally.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-5-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:08:47 +0000 (13:08 -0700)]
watchdog: ziirave_wdt: Be more verbose during firmware update
Add more error logging to ziirave_firm_upload() for diagnostics.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-4-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:08:46 +0000 (13:08 -0700)]
watchdog: ziirave_wdt: Be verbose about errors in probe()
The driver is quite silent in case of probe failure, which makes it
more difficult to diagnose problem from the kernel log. Add logging to
all of the silent error paths ziirave_wdt_probe() to improve that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-3-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Andrey Smirnov [Mon, 12 Aug 2019 20:08:45 +0000 (13:08 -0700)]
watchdog: ziirave_wdt: Add missing newline
Add missing newline.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-2-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Anson Huang [Mon, 12 Aug 2019 08:44:34 +0000 (16:44 +0800)]
watchdog: imx_sc: Remove unnecessary error log
An error message is already displayed by watchdog_register_device()
when failed, so no need to have error log again for failure of
calling devm_watchdog_register_device().
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812084434.13316-1-Anson.Huang@nxp.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Rasmus Villemoes [Mon, 12 Aug 2019 13:13:56 +0000 (15:13 +0200)]
watchdog: imx2_wdt: fix min() calculation in imx2_wdt_set_timeout
Converting from ms to s requires dividing by 1000, not multiplying. So
this is currently taking the smaller of new_timeout and 1.28e8,
i.e. effectively new_timeout.
The driver knows what it set max_hw_heartbeat_ms to, so use that
value instead of doing a division at run-time.
FWIW, this can easily be tested by booting into a busybox shell and
doing "watchdog -t 5 -T 130 /dev/watchdog" - without this patch, the
watchdog fires after 130&127 == 2 seconds.
Fixes:
b07e228eee69 "watchdog: imx2_wdt: Fix set_timeout for big timeout values"
Cc: stable@vger.kernel.org # 5.2 plus anything the above got backported to
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812131356.23039-1-linux@rasmusvillemoes.dk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Arnd Bergmann [Wed, 14 Aug 2019 20:42:32 +0000 (22:42 +0200)]
watchdog: cpwd: use generic compat_ptr_ioctl
The cpwd_compat_ioctl() contains a bogus mutex that dates
back to a leftover BKL instance.
Simplify the implementation by using the new compat_ptr_ioctl()
helper function that will do the right thing for all calls
here.
Note that WIOCSTART/WIOCSTOP don't take any arguments, so
the compat_ptr() conversion is not needed here, but it also
doesn't hurt.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190814204259.120942-6-arnd@arndb.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Guenter Roeck [Sun, 11 Aug 2019 21:23:46 +0000 (14:23 -0700)]
watchdog: diag288_wdt: Remove leftover includes from conversion to watchdog API
Commit
f7a94db4e959 ("s390/watchdog: use watchdog API") converted
the driver to use the watchdog API, but some includes as well as
MODULE_ALIAS_MISCDEV() were missed.
Cc: Philipp Hachtmann <phacht@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Arnd Bergmann [Fri, 9 Aug 2019 20:27:34 +0000 (22:27 +0200)]
watchdog: remove w90x900 driver
The ARM w90x900 platform is getting removed, so this driver is obsolete
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190809202749.742267-7-arnd@arndb.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Arnd Bergmann [Fri, 9 Aug 2019 20:27:32 +0000 (22:27 +0200)]
watchdog: remove ks8695 driver
The platform is getting removed, so there are no remaining
users of this driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190809202749.742267-5-arnd@arndb.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Arnd Bergmann [Fri, 9 Aug 2019 14:40:29 +0000 (16:40 +0200)]
watchdog: pnx4008_wdt: allow compile-testing
The only thing that prevents building this driver on other
platforms is the mach/hardware.h include, which is not actually
used here at all, so remove the line and allow CONFIG_COMPILE_TEST.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20190809144043.476786-4-arnd@arndb.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Gustavo A. R. Silva [Tue, 6 Aug 2019 07:39:53 +0000 (02:39 -0500)]
watchdog: jz4740: Fix unused variable warning in jz4740_wdt_probe
Fix the following warning (Building: ci20_defconfig mips):
drivers/watchdog/jz4740_wdt.c: In function ‘jz4740_wdt_probe’:
drivers/watchdog/jz4740_wdt.c:165:6: warning: unused variable ‘ret’ [-Wunused-variable]
int ret;
^~~
Fixes:
9ee644c9326c ("watchdog: jz4740_wdt: drop warning after registering device")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190806073953.GA13685@embeddedor
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Stephen Boyd [Tue, 30 Jul 2019 18:15:48 +0000 (11:15 -0700)]
watchdog: Remove dev_err() usage after platform_get_irq()
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-watchdog@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Gustavo A. R. Silva [Tue, 30 Jul 2019 01:46:50 +0000 (20:46 -0500)]
watchdog: riowd: Mark expected switch fall-through
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings (Building: sparc64):
drivers/watchdog/riowd.c: In function ‘riowd_ioctl’:
drivers/watchdog/riowd.c:136:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
riowd_writereg(p, riowd_timeout, WDTO_INDEX);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/watchdog/riowd.c:139:2: note: here
case WDIOC_GETTIMEOUT:
^~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190730014650.GA31309@embeddedor
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Gustavo A. R. Silva [Mon, 29 Jul 2019 22:31:59 +0000 (17:31 -0500)]
watchdog: wdt977: Mark expected switch fall-through
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: arm):
drivers/watchdog/wdt977.c: In function ‘wdt977_ioctl’:
LD [M] drivers/media/platform/vicodec/vicodec.o
drivers/watchdog/wdt977.c:400:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
wdt977_keepalive();
^~~~~~~~~~~~~~~~~~
drivers/watchdog/wdt977.c:403:2: note: here
case WDIOC_GETTIMEOUT:
^~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190729223159.GA20878@embeddedor
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Gustavo A. R. Silva [Mon, 29 Jul 2019 20:06:02 +0000 (15:06 -0500)]
watchdog: scx200_wdt: Mark expected switch fall-through
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: i386):
drivers/watchdog/scx200_wdt.c: In function ‘scx200_wdt_ioctl’:
drivers/watchdog/scx200_wdt.c:188:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
scx200_wdt_ping();
^~~~~~~~~~~~~~~~~
drivers/watchdog/scx200_wdt.c:189:2: note: here
case WDIOC_GETTIMEOUT:
^~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190729200602.GA6854@embeddedor
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Gustavo A. R. Silva [Mon, 29 Jul 2019 15:10:33 +0000 (10:10 -0500)]
watchdog: Mark expected switch fall-throughs
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/watchdog/ar7_wdt.c: warning: this statement may fall
through [-Wimplicit-fallthrough=]: => 237:3
drivers/watchdog/pcwd.c: warning: this statement may fall
through [-Wimplicit-fallthrough=]: => 653:3
drivers/watchdog/sb_wdog.c: warning: this statement may fall
through [-Wimplicit-fallthrough=]: => 204:3
drivers/watchdog/wdt.c: warning: this statement may fall
through [-Wimplicit-fallthrough=]: => 391:3
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190729151033.GA10143@embeddedor
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Christophe JAILLET [Sun, 21 Jul 2019 12:55:47 +0000 (14:55 +0200)]
watchdog: ath79_wdt: fix a typo in the name of a function
It is likely that 'ath97_wdt_shutdown()' should be 'ath79_wdt_shutdown()'
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Linus Torvalds [Tue, 23 Jul 2019 22:34:59 +0000 (15:34 -0700)]
Merge branch 'parisc-5.3-3' of git://git./linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
- Fix build issues when kprobes are enabled
- Speed up ITLB/DTLB cache flushes when running on machines with
combined TLBs
* 'parisc-5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Flush ITLB in flush_tlb_all_local() only on split TLB machines
parisc: add kprobe_fault_handler()
Linus Torvalds [Mon, 22 Jul 2019 16:30:34 +0000 (09:30 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull preemption Kconfig fix from Thomas Gleixner:
"The PREEMPT_RT stub config renamed PREEMPT to PREEMPT_LL and defined
PREEMPT outside of the menu and made it selectable by both PREEMPT_LL
and PREEMPT_RT.
Stupid me missed that 114 defconfigs select CONFIG_PREEMPT which
obviously can't work anymore. oldconfig builds are affected as well,
but it's more obvious as the user gets asked. [old]defconfig silently
fixes it up and selects PREEMPT_NONE.
Unbreak it by undoing the rename and adding a intermediate config
symbol which is selected by both PREEMPT and PREEMPT_RT. That requires
to chase down a few #ifdefs, but it's better than tweaking 114
defconfigs and annoying users"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/rt, Kconfig: Unbreak def/oldconfig with CONFIG_PREEMPT=y
Linus Torvalds [Mon, 22 Jul 2019 16:14:19 +0000 (09:14 -0700)]
Merge tag 'for-linus-
20190722' of git://git./linux/kernel/git/brauner/linux
Pull pidfd polling fix from Christian Brauner:
"A fix for pidfd polling. It ensures that the task's exit state is
visible to all waiters"
* tag 'for-linus-
20190722' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
pidfd: fix a poll race when setting exit_state
Linus Torvalds [Mon, 22 Jul 2019 16:08:38 +0000 (09:08 -0700)]
Merge tag 'for-5.3-rc1-tag' of git://git./linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- fixes for leaks caused by recently merged patches
- one build fix
- a fix to prevent mixing of incompatible features
* tag 'for-5.3-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: don't leak extent_map in btrfs_get_io_geometry()
btrfs: free checksum hash on in close_ctree
btrfs: Fix build error while LIBCRC32C is module
btrfs: inode: Don't compress if NODATASUM or NODATACOW set
Thomas Gleixner [Mon, 22 Jul 2019 15:59:19 +0000 (17:59 +0200)]
sched/rt, Kconfig: Unbreak def/oldconfig with CONFIG_PREEMPT=y
The merge of the CONFIG_PREEMPT_RT stub renamed CONFIG_PREEMPT to
CONFIG_PREEMPT_LL which causes all defconfigs which have CONFIG_PREEMPT=y
set to fall back to CONFIG_PREEMPT_NONE because CONFIG_PREEMPT depends on
the preemption mode choice wich defaults to NONE. This also affects
oldconfig builds.
So rather than changing 114 defconfig files and being an annoyance to
users, revert the rename and select a new config symbol PREEMPTION. That
keeps everything working smoothly and the revelant ifdef's are going to be
fixed up step by step.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Fixes:
a50a3f4b6a31 ("sched/rt, Kconfig: Introduce CONFIG_PREEMPT_RT")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Linus Torvalds [Mon, 22 Jul 2019 16:01:47 +0000 (09:01 -0700)]
Merge tag 'media/v5.3-2' of git://git./linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"For two regressions in media core:
- v4l2-subdev: fix regression in check_pad()
- videodev2.h: change V4L2_PIX_FMT_BGRA444 define: fourcc was already
in use"
* tag 'media/v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: videodev2.h: change V4L2_PIX_FMT_BGRA444 define: fourcc was already in use
media: v4l2-subdev: fix regression in check_pad()
Linus Torvalds [Mon, 22 Jul 2019 15:49:22 +0000 (08:49 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Several netfilter fixes including a nfnetlink deadlock fix from
Florian Westphal and fix for dropping VRF packets from Miaohe Lin.
2) Flow offload fixes from Pablo Neira Ayuso including a fix to restore
proper block sharing.
3) Fix r8169 PHY init from Thomas Voegtle.
4) Fix memory leak in mac80211, from Lorenzo Bianconi.
5) Missing NULL check on object allocation in cxgb4, from Navid
Emamdoost.
6) Fix scaling of RX power in sfp phy driver, from Andrew Lunn.
7) Check that there is actually an ip header to access in skb->data in
VRF, from Peter Kosyh.
8) Remove spurious rcu unlock in hv_netvsc, from Haiyang Zhang.
9) One more tweak the the TCP fragmentation memory limit changes, to be
less harmful to applications setting small SO_SNDBUF values. From
Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (40 commits)
tcp: be more careful in tcp_fragment()
hv_netvsc: Fix extra rcu_read_unlock in netvsc_recv_callback()
vrf: make sure skb->data contains ip header to make routing
connector: remove redundant input callback from cn_dev
qed: Prefer pcie_capability_read_word()
igc: Prefer pcie_capability_read_word()
cxgb4: Prefer pcie_capability_read_word()
be2net: Synchronize be_update_queues with dev_watchdog
bnx2x: Prevent load reordering in tx completion processing
net: phy: sfp: hwmon: Fix scaling of RX power
net: sched: verify that q!=NULL before setting q->flags
chelsio: Fix a typo in a function name
allocate_flower_entry: should check for null deref
net: hns3: typo in the name of a constant
kbuild: add net/netfilter/nf_tables_offload.h to header-test blacklist.
tipc: Fix a typo
mac80211: don't warn about CW params when not using them
mac80211: fix possible memory leak in ieee80211_assign_beacon
nl80211: fix NL80211_HE_MAX_CAPABILITY_LEN
nl80211: fix VENDOR_CMD_RAW_DATA
...
Suren Baghdasaryan [Wed, 17 Jul 2019 17:21:00 +0000 (13:21 -0400)]
pidfd: fix a poll race when setting exit_state
There is a race between reading task->exit_state in pidfd_poll and
writing it after do_notify_parent calls do_notify_pidfd. Expected
sequence of events is:
CPU 0 CPU 1
------------------------------------------------
exit_notify
do_notify_parent
do_notify_pidfd
tsk->exit_state = EXIT_DEAD
pidfd_poll
if (tsk->exit_state)
However nothing prevents the following sequence:
CPU 0 CPU 1
------------------------------------------------
exit_notify
do_notify_parent
do_notify_pidfd
pidfd_poll
if (tsk->exit_state)
tsk->exit_state = EXIT_DEAD
This causes a polling task to wait forever, since poll blocks because
exit_state is 0 and the waiting task is not notified again. A stress
test continuously doing pidfd poll and process exits uncovered this bug.
To fix it, we make sure that the task's exit_state is always set before
calling do_notify_pidfd.
Fixes:
b53b0b9d9a6 ("pidfd: add polling support")
Cc: kernel-team@android.com
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Link: https://lore.kernel.org/r/20190717172100.261204-1-joel@joelfernandes.org
[christian@brauner.io: adapt commit message and drop unneeded changes from wait_task_zombie]
Signed-off-by: Christian Brauner <christian@brauner.io>
Eric Dumazet [Fri, 19 Jul 2019 18:52:33 +0000 (11:52 -0700)]
tcp: be more careful in tcp_fragment()
Some applications set tiny SO_SNDBUF values and expect
TCP to just work. Recent patches to address CVE-2019-11478
broke them in case of losses, since retransmits might
be prevented.
We should allow these flows to make progress.
This patch allows the first and last skb in retransmit queue
to be split even if memory limits are hit.
It also adds the some room due to the fact that tcp_sendmsg()
and tcp_sendpage() might overshoot sk_wmem_queued by about one full
TSO skb (64KB size). Note this allowance was already present
in stable backports for kernels < 4.15
Note for < 4.15 backports :
tcp_rtx_queue_tail() will probably look like :
static inline struct sk_buff *tcp_rtx_queue_tail(const struct sock *sk)
{
struct sk_buff *skb = tcp_send_head(sk);
return skb ? tcp_write_queue_prev(sk, skb) : tcp_write_queue_tail(sk);
}
Fixes:
f070ef2ac667 ("tcp: tcp_fragment() should apply sane memory limits")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrew Prout <aprout@ll.mit.edu>
Tested-by: Andrew Prout <aprout@ll.mit.edu>
Tested-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Tested-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Christoph Paasch <cpaasch@apple.com>
Cc: Jonathan Looney <jtl@netflix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Fri, 19 Jul 2019 17:33:51 +0000 (17:33 +0000)]
hv_netvsc: Fix extra rcu_read_unlock in netvsc_recv_callback()
There is an extra rcu_read_unlock left in netvsc_recv_callback(),
after a previous patch that removes RCU from this function.
This patch removes the extra RCU unlock.
Fixes:
345ac08990b8 ("hv_netvsc: pass netvsc_device to receive callback")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 21 Jul 2019 21:05:38 +0000 (14:05 -0700)]
Linus 5.3-rc1
Peter Kosyh [Fri, 19 Jul 2019 08:11:47 +0000 (11:11 +0300)]
vrf: make sure skb->data contains ip header to make routing
vrf_process_v4_outbound() and vrf_process_v6_outbound() do routing
using ip/ipv6 addresses, but don't make sure the header is available
in skb->data[] (skb_headlen() is less then header size).
Case:
1) igb driver from intel.
2) Packet size is greater then 255.
3) MPLS forwards to VRF device.
So, patch adds pskb_may_pull() calls in vrf_process_v4/v6_outbound()
functions.
Signed-off-by: Peter Kosyh <p.kosyh@gmail.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasily Averin [Thu, 18 Jul 2019 04:26:46 +0000 (07:26 +0300)]
connector: remove redundant input callback from cn_dev
A small cleanup: this callback is never used.
Originally fixed by Stanislav Kinsburskiy <skinsbursky@virtuozzo.com>
for OpenVZ7 bug OVZ-6877
cc: stanislav.kinsburskiy@gmail.com
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frederick Lawler [Thu, 18 Jul 2019 02:07:42 +0000 (21:07 -0500)]
qed: Prefer pcie_capability_read_word()
Commit
8c0d3a02c130 ("PCI: Add accessors for PCI Express Capability")
added accessors for the PCI Express Capability so that drivers didn't
need to be aware of differences between v1 and v2 of the PCI
Express Capability.
Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Acked-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frederick Lawler [Thu, 18 Jul 2019 02:07:39 +0000 (21:07 -0500)]
igc: Prefer pcie_capability_read_word()
Commit
8c0d3a02c130 ("PCI: Add accessors for PCI Express Capability")
added accessors for the PCI Express Capability so that drivers didn't
need to be aware of differences between v1 and v2 of the PCI
Express Capability.
Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frederick Lawler [Thu, 18 Jul 2019 02:07:36 +0000 (21:07 -0500)]
cxgb4: Prefer pcie_capability_read_word()
Commit
8c0d3a02c130 ("PCI: Add accessors for PCI Express Capability")
added accessors for the PCI Express Capability so that drivers didn't
need to be aware of differences between v1 and v2 of the PCI
Express Capability.
Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Poirier [Thu, 18 Jul 2019 01:42:18 +0000 (10:42 +0900)]
be2net: Synchronize be_update_queues with dev_watchdog
As pointed out by Firo Yang, a netdev tx timeout may trigger just before an
ethtool set_channels operation is started. be_tx_timeout(), which dumps
some queue structures, is not written to run concurrently with
be_update_queues(), which frees/allocates those queues structures. Add some
synchronization between the two.
Message-id: <CH2PR18MB31898E033896F9760D36BFF288C90@CH2PR18MB3189.namprd18.prod.outlook.com>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Brian King [Mon, 15 Jul 2019 21:41:50 +0000 (16:41 -0500)]
bnx2x: Prevent load reordering in tx completion processing
This patch fixes an issue seen on Power systems with bnx2x which results
in the skb is NULL WARN_ON in bnx2x_free_tx_pkt firing due to the skb
pointer getting loaded in bnx2x_free_tx_pkt prior to the hw_cons
load in bnx2x_tx_int. Adding a read memory barrier resolves the issue.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 21 Jul 2019 16:50:08 +0000 (18:50 +0200)]
net: phy: sfp: hwmon: Fix scaling of RX power
The RX power read from the SFP uses units of 0.1uW. This must be
scaled to units of uW for HWMON. This requires a divide by 10, not the
current 100.
With this change in place, sensors(1) and ethtool -m agree:
sff2-isa-0000
Adapter: ISA adapter
in0: +3.23 V
temp1: +33.1 C
power1: 270.00 uW
power2: 200.00 uW
curr1: +0.01 A
Laser output power : 0.2743 mW / -5.62 dBm
Receiver signal average optical power : 0.2014 mW / -6.96 dBm
Reported-by: chris.healy@zii.aero
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes:
1323061a018a ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Buslov [Sun, 21 Jul 2019 14:44:12 +0000 (17:44 +0300)]
net: sched: verify that q!=NULL before setting q->flags
In function int tc_new_tfilter() q pointer can be NULL when adding filter
on a shared block. With recent change that resets TCQ_F_CAN_BYPASS after
filter creation, following NULL pointer dereference happens in case parent
block is shared:
[ 212.925060] BUG: kernel NULL pointer dereference, address:
0000000000000010
[ 212.925445] #PF: supervisor write access in kernel mode
[ 212.925709] #PF: error_code(0x0002) - not-present page
[ 212.925965] PGD
8000000827923067 P4D
8000000827923067 PUD
827924067 PMD 0
[ 212.926302] Oops: 0002 [#1] SMP KASAN PTI
[ 212.926539] CPU: 18 PID: 2617 Comm: tc Tainted: G B 5.2.0+ #512
[ 212.926938] Hardware name: Supermicro SYS-2028TP-DECR/X10DRT-P, BIOS 2.0b 03/30/2017
[ 212.927364] RIP: 0010:tc_new_tfilter+0x698/0xd40
[ 212.927633] Code: 74 0d 48 85 c0 74 08 48 89 ef e8 03 aa 62 00 48 8b 84 24 a0 00 00 00 48 8d 78 10 48 89 44 24 18 e8 4d 0c 6b ff 48 8b 44 24 18 <83> 60 10 f
b 48 85 ed 0f 85 3d fe ff ff e9 4f fe ff ff e8 81 26 f8
[ 212.928607] RSP: 0018:
ffff88884fd5f5d8 EFLAGS:
00010296
[ 212.928905] RAX:
0000000000000000 RBX:
0000000000000000 RCX:
dffffc0000000000
[ 212.929201] RDX:
0000000000000007 RSI:
0000000000000004 RDI:
0000000000000297
[ 212.929402] RBP:
ffff88886bedd600 R08:
ffffffffb91d4b51 R09:
fffffbfff7616e4d
[ 212.929609] R10:
fffffbfff7616e4c R11:
ffffffffbb0b7263 R12:
ffff88886bc61040
[ 212.929803] R13:
ffff88884fd5f950 R14:
ffffc900039c5000 R15:
ffff88835e927680
[ 212.929999] FS:
00007fe7c50b6480(0000) GS:
ffff88886f980000(0000) knlGS:
0000000000000000
[ 212.930235] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 212.930394] CR2:
0000000000000010 CR3:
000000085bd04002 CR4:
00000000001606e0
[ 212.930588] Call Trace:
[ 212.930682] ? tc_del_tfilter+0xa40/0xa40
[ 212.930811] ? __lock_acquire+0x5b5/0x2460
[ 212.930948] ? find_held_lock+0x85/0xa0
[ 212.931081] ? tc_del_tfilter+0xa40/0xa40
[ 212.931201] rtnetlink_rcv_msg+0x4ab/0x5f0
[ 212.931332] ? rtnl_dellink+0x490/0x490
[ 212.931454] ? lockdep_hardirqs_on+0x260/0x260
[ 212.931589] ? netlink_deliver_tap+0xab/0x5a0
[ 212.931717] ? match_held_lock+0x1b/0x240
[ 212.931844] netlink_rcv_skb+0xd0/0x200
[ 212.931958] ? rtnl_dellink+0x490/0x490
[ 212.932079] ? netlink_ack+0x440/0x440
[ 212.932205] ? netlink_deliver_tap+0x161/0x5a0
[ 212.932335] ? lock_downgrade+0x360/0x360
[ 212.932457] ? lock_acquire+0xe5/0x210
[ 212.932579] netlink_unicast+0x296/0x350
[ 212.932705] ? netlink_attachskb+0x390/0x390
[ 212.932834] ? _copy_from_iter_full+0xe0/0x3a0
[ 212.932976] netlink_sendmsg+0x394/0x600
[ 212.937998] ? netlink_unicast+0x350/0x350
[ 212.943033] ? move_addr_to_kernel.part.0+0x90/0x90
[ 212.948115] ? netlink_unicast+0x350/0x350
[ 212.953185] sock_sendmsg+0x96/0xa0
[ 212.958099] ___sys_sendmsg+0x482/0x520
[ 212.962881] ? match_held_lock+0x1b/0x240
[ 212.967618] ? copy_msghdr_from_user+0x250/0x250
[ 212.972337] ? lock_downgrade+0x360/0x360
[ 212.976973] ? rwlock_bug.part.0+0x60/0x60
[ 212.981548] ? __mod_node_page_state+0x1f/0xa0
[ 212.986060] ? match_held_lock+0x1b/0x240
[ 212.990567] ? find_held_lock+0x85/0xa0
[ 212.994989] ? do_user_addr_fault+0x349/0x5b0
[ 212.999387] ? lock_downgrade+0x360/0x360
[ 213.003713] ? find_held_lock+0x85/0xa0
[ 213.007972] ? __fget_light+0xa1/0xf0
[ 213.012143] ? sockfd_lookup_light+0x91/0xb0
[ 213.016165] __sys_sendmsg+0xba/0x130
[ 213.020040] ? __sys_sendmsg_sock+0xb0/0xb0
[ 213.023870] ? handle_mm_fault+0x337/0x470
[ 213.027592] ? page_fault+0x8/0x30
[ 213.031316] ? lockdep_hardirqs_off+0xbe/0x100
[ 213.034999] ? mark_held_locks+0x24/0x90
[ 213.038671] ? do_syscall_64+0x1e/0xe0
[ 213.042297] do_syscall_64+0x74/0xe0
[ 213.045828] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 213.049354] RIP: 0033:0x7fe7c527c7b8
[ 213.052792] Code: 89 02 48 c7 c0 ff ff ff ff eb bb 0f 1f 80 00 00 00 00 f3 0f 1e fa 48 8d 05 65 8f 0c 00 8b 00 85 c0 75 17 b8 2e 00 00 00 0f 05 <48> 3d 00 f
0 ff ff 77 58 c3 0f 1f 80 00 00 00 00 48 83 ec 28 89 54
[ 213.060269] RSP: 002b:
00007ffc3f7908a8 EFLAGS:
00000246 ORIG_RAX:
000000000000002e
[ 213.064144] RAX:
ffffffffffffffda RBX:
000000005d34716f RCX:
00007fe7c527c7b8
[ 213.068094] RDX:
0000000000000000 RSI:
00007ffc3f790910 RDI:
0000000000000003
[ 213.072109] RBP:
0000000000000000 R08:
0000000000000001 R09:
00007fe7c5340cc0
[ 213.076113] R10:
0000000000404ec2 R11:
0000000000000246 R12:
0000000000000080
[ 213.080146] R13:
0000000000480640 R14:
0000000000000080 R15:
0000000000000000
[ 213.084147] Modules linked in: act_gact cls_flower sch_ingress nfsv3 nfs_acl nfs lockd grace fscache bridge stp llc sunrpc intel_rapl_msr intel_rapl_common
\e[<1;69;32Msb_edac rdma_ucm rdma_cm x86_pkg_temp_thermal iw_cm intel_powerclamp ib_cm coretemp kvm_intel kvm irqbypass mlx5_ib ib_uverbs ib_core crct10dif_pclmul crc32_pc
lmul crc32c_intel ghash_clmulni_intel mlx5_core intel_cstate intel_uncore iTCO_wdt igb iTCO_vendor_support mlxfw mei_me ptp ses intel_rapl_perf mei pcspkr ipmi
_ssif i2c_i801 joydev enclosure pps_core lpc_ich ioatdma wmi dca ipmi_si ipmi_devintf ipmi_msghandler acpi_power_meter acpi_pad ast i2c_algo_bit drm_vram_helpe
r ttm drm_kms_helper drm mpt3sas raid_class scsi_transport_sas
[ 213.112326] CR2:
0000000000000010
[ 213.117429] ---[ end trace
adb58eb0a4ee6283 ]---
Verify that q pointer is not NULL before setting the 'flags' field.
Fixes:
3f05e6886a59 ("net_sched: unset TCQ_F_CAN_BYPASS when adding filters")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Sun, 21 Jul 2019 13:16:05 +0000 (15:16 +0200)]
chelsio: Fix a typo in a function name
It is likely that 'my3216_poll()' should be 'my3126_poll()'. (1 and 2
switched in 3126.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Navid Emamdoost [Sun, 21 Jul 2019 06:37:31 +0000 (01:37 -0500)]
allocate_flower_entry: should check for null deref
allocate_flower_entry does not check for allocation success, but tries
to deref the result. I only moved the spin_lock under null check, because
the caller is checking allocation's status at line 652.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Sun, 21 Jul 2019 13:08:31 +0000 (15:08 +0200)]
net: hns3: typo in the name of a constant
All constant in 'enum HCLGE_MBX_OPCODE' start with HCLGE, except
'HLCGE_MBX_PUSH_VLAN_INFO' (C and L switched)
s/HLC/HCL/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeremy Sowden [Sun, 21 Jul 2019 11:31:05 +0000 (12:31 +0100)]
kbuild: add net/netfilter/nf_tables_offload.h to header-test blacklist.
net/netfilter/nf_tables_offload.h includes net/netfilter/nf_tables.h
which is itself on the blacklist.
Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Sun, 21 Jul 2019 10:38:11 +0000 (12:38 +0200)]
tipc: Fix a typo
s/tipc_toprsv_listener_data_ready/tipc_topsrv_listener_data_ready/
(r and s switched in topsrv)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 21 Jul 2019 18:39:05 +0000 (11:39 -0700)]
Merge tag 'mac80211-for-davem-2019-07-20' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
We have a handful of fixes:
* ignore bad CW parameters if we aren't using them,
instead of warning
* fix operation (and then build) with the new netlink vendor
command policy requirement
* fix a memory leak in an error path when setting beacons
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 21 Jul 2019 17:28:39 +0000 (10:28 -0700)]
Merge tag 'devicetree-fixes-for-5.3' of git://git./linux/kernel/git/robh/linux
Pull Devicetree fixes from Rob Herring:
"Fix several warnings/errors in validation of binding schemas"
* tag 'devicetree-fixes-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: pinctrl: stm32: Fix missing 'clocks' property in examples
dt-bindings: iio: ad7124: Fix dtc warnings in example
dt-bindings: iio: avia-hx711: Fix avdd-supply typo in example
dt-bindings: pinctrl: aspeed: Fix AST2500 example errors
dt-bindings: pinctrl: aspeed: Fix 'compatible' schema errors
dt-bindings: riscv: Limit cpus schema to only check RiscV 'cpu' nodes
dt-bindings: Ensure child nodes are of type 'object'
Linus Torvalds [Sun, 21 Jul 2019 17:09:43 +0000 (10:09 -0700)]
Merge branch 'work.misc' of git://git./linux/kernel/git/viro/vfs
Pull vfs documentation typo fix from Al Viro.
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
typo fix: it's d_make_root, not d_make_inode...
Linus Torvalds [Sun, 21 Jul 2019 17:01:17 +0000 (10:01 -0700)]
Merge tag '5.3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Two fixes for stable, one that had dependency on earlier patch in this
merge window and can now go in, and a perf improvement in SMB3 open"
* tag '5.3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module number
cifs: flush before set-info if we have writeable handles
smb3: optimize open to not send query file internal info
cifs: copy_file_range needs to strip setuid bits and update timestamps
CIFS: fix deadlock in cached root handling
Qian Cai [Thu, 11 Jul 2019 16:17:45 +0000 (12:17 -0400)]
iommu/amd: fix a crash in iova_magazine_free_pfns
The commit
b3aa14f02254 ("iommu: remove the mapping_error dma_map_ops
method") incorrectly changed the checking from dma_ops_alloc_iova() in
map_sg() causes a crash under memory pressure as dma_ops_alloc_iova()
never return DMA_MAPPING_ERROR on failure but 0, so the error handling
is all wrong.
kernel BUG at drivers/iommu/iova.c:801!
Workqueue: kblockd blk_mq_run_work_fn
RIP: 0010:iova_magazine_free_pfns+0x7d/0xc0
Call Trace:
free_cpu_cached_iovas+0xbd/0x150
alloc_iova_fast+0x8c/0xba
dma_ops_alloc_iova.isra.6+0x65/0xa0
map_sg+0x8c/0x2a0
scsi_dma_map+0xc6/0x160
pqi_aio_submit_io+0x1f6/0x440 [smartpqi]
pqi_scsi_queue_command+0x90c/0xdd0 [smartpqi]
scsi_queue_rq+0x79c/0x1200
blk_mq_dispatch_rq_list+0x4dc/0xb70
blk_mq_sched_dispatch_requests+0x249/0x310
__blk_mq_run_hw_queue+0x128/0x200
blk_mq_run_work_fn+0x27/0x30
process_one_work+0x522/0xa10
worker_thread+0x63/0x5b0
kthread+0x1d2/0x1f0
ret_from_fork+0x22/0x40
Fixes:
b3aa14f02254 ("iommu: remove the mapping_error dma_map_ops method")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Rapoport [Tue, 30 Apr 2019 14:27:50 +0000 (17:27 +0300)]
hexagon: switch to generic version of pte allocation
The hexagon implementation pte_alloc_one(), pte_alloc_one_kernel(),
pte_free_kernel() and pte_free() is identical to the generic except of
lack of __GFP_ACCOUNT for the user PTEs allocation.
Switch hexagon to use generic version of these functions.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 21 Jul 2019 16:46:59 +0000 (09:46 -0700)]
Merge tag 'ntb-5.3' of git://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"New feature to add support for NTB virtual MSI interrupts, the ability
to test and use this feature in the NTB transport layer.
Also, bug fixes for the AMD and Switchtec drivers, as well as some
general patches"
* tag 'ntb-5.3' of git://github.com/jonmason/ntb: (22 commits)
NTB: Describe the ntb_msi_test client in the documentation.
NTB: Add MSI interrupt support to ntb_transport
NTB: Add ntb_msi_test support to ntb_test
NTB: Introduce NTB MSI Test Client
NTB: Introduce MSI library
NTB: Rename ntb.c to support multiple source files in the module
NTB: Introduce functions to calculate multi-port resource index
NTB: Introduce helper functions to calculate logical port number
PCI/switchtec: Add module parameter to request more interrupts
PCI/MSI: Support allocating virtual MSI interrupts
ntb_hw_switchtec: Fix setup MW with failure bug
ntb_hw_switchtec: Skip unnecessary re-setup of shared memory window for crosslink case
ntb_hw_switchtec: Remove redundant steps of switchtec_ntb_reinit_peer() function
NTB: correct ntb_dev_ops and ntb_dev comment typos
NTB: amd: Silence shift wrapping warning in amd_ntb_db_vector_mask()
ntb_hw_switchtec: potential shift wrapping bug in switchtec_ntb_init_sndev()
NTB: ntb_transport: Ensure qp->tx_mw_dma_addr is initaliazed
NTB: ntb_hw_amd: set peer limit register
NTB: ntb_perf: Clear stale values in doorbell and command SPAD register
NTB: ntb_perf: Disable NTB link after clearing peer XLAT registers
...
Helge Deller [Sat, 20 Jul 2019 22:55:48 +0000 (00:55 +0200)]
parisc: Flush ITLB in flush_tlb_all_local() only on split TLB machines
flush_tlb_all_local() flushes the ITLB and DTLB of the CPU.
In case the machine does not have separate ITLBs and DTLBs, use the
alternative functionality to replace the code which flushes the ITLB
with nops while keeping the code which flushes the DTLB.
Signed-off-by: Helge Deller <deller@gmx.de>
Sven Schnelle [Sun, 21 Jul 2019 09:00:39 +0000 (11:00 +0200)]
parisc: add kprobe_fault_handler()
Add kprobe_fault_handler() to fix compilation for PA-RISC.
On PA-RISC we actually don't need that function as the recovery counter
is restored after interrupt. See the PA-RISC 2.0 Architecture Manual,
pg. 4-8, Figure 4-4: "Interruption Processing".
Fixes:
b98cca444d28 ("mm, kprobes: generalize and rename notify_page_fault() as kprobe_page_fault()")
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Al Viro [Sun, 21 Jul 2019 03:17:30 +0000 (23:17 -0400)]
typo fix: it's d_make_root, not d_make_inode...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Rob Herring [Tue, 16 Jul 2019 21:34:40 +0000 (15:34 -0600)]
dt-bindings: pinctrl: stm32: Fix missing 'clocks' property in examples
Now that examples are validated against the DT schema, an error with
required 'clocks' property missing is exposed:
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@
40020000: gpio@0: 'clocks' is a required property
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@
50020000: gpio@1000: 'clocks' is a required property
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@
50020000: gpio@2000: 'clocks' is a required property
Add the missing 'clocks' properties to the examples to fix the errors.
Fixes:
2c9239c125f0 ("dt-bindings: pinctrl: Convert stm32 pinctrl bindings to json-schema")
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Rob Herring [Tue, 16 Jul 2019 20:21:56 +0000 (14:21 -0600)]
dt-bindings: iio: ad7124: Fix dtc warnings in example
With the conversion to DT schema, the examples are now compiled with
dtc. The ad7124 binding example has the following warning:
Documentation/devicetree/bindings/iio/adc/adi,ad7124.example.dts:19.11-21: \
Warning (reg_format): /example-0/adc@0:reg: property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
There's a default #size-cells and #address-cells values of 1 for
examples. For examples needing different values such as this one on a
SPI bus, they need to provide a SPI bus parent node.
Fixes:
26ae15e62d3c ("Convert AD7124 bindings documentation to YAML format.")
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Rob Herring [Tue, 16 Jul 2019 20:13:29 +0000 (14:13 -0600)]
dt-bindings: iio: avia-hx711: Fix avdd-supply typo in example
Now that examples are validated against the DT schema, a typo in
avia-hx711 example generates a warning:
Documentation/devicetree/bindings/iio/adc/avia-hx711.example.dt.yaml: weight: 'avdd-supply' is a required property
Fix the typo.
Fixes:
5150ec3fe125 ("avia-hx711.yaml: transform DT binding to YAML")
Cc: Andreas Klinger <ak@it-klinger.de>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Rob Herring [Mon, 15 Jul 2019 22:48:41 +0000 (16:48 -0600)]
dt-bindings: pinctrl: aspeed: Fix AST2500 example errors
The schema examples are now validated against the schema itself. The
AST2500 pinctrl schema has a couple of errors:
Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.example.dt.yaml: \
example-0: $nodename:0: 'example-0' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.example.dt.yaml: \
pinctrl: aspeed,external-nodes: [[1, 2]] is too short
Fixes:
0a617de16730 ("dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema")
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Joel Stanley <joel@jms.id.au>
Cc: linux-aspeed@lists.ozlabs.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Rob Herring <robh@kernel.org>
Rob Herring [Mon, 15 Jul 2019 22:37:25 +0000 (16:37 -0600)]
dt-bindings: pinctrl: aspeed: Fix 'compatible' schema errors
The Aspeed pinctl schema have errors in the 'compatible' schema:
Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml: \
properties:compatible:enum: ['aspeed', 'ast2400-pinctrl', 'aspeed', 'g4-pinctrl'] has non-unique elements
Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml: \
properties:compatible:enum: ['aspeed', 'ast2500-pinctrl', 'aspeed', 'g5-pinctrl'] has non-unique elements
Flow style sequences have to be quoted if the vales contain ','. Fix
this by using the more common one line per entry formatting.
Fixes:
0a617de16730 ("dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema")
Fixes:
07457937bb5c ("dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema")
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Joel Stanley <joel@jms.id.au>
Cc: linux-aspeed@lists.ozlabs.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Rob Herring <robh@kernel.org>
Rob Herring [Wed, 26 Jun 2019 23:57:59 +0000 (17:57 -0600)]
dt-bindings: riscv: Limit cpus schema to only check RiscV 'cpu' nodes
Matching on the 'cpus' node was a bad choice because the schema is
incorrectly applied to non-RiscV cpus nodes. As we now have a common cpus
schema which checks the general structure, it is also redundant to do so
in the Risc-V CPU schema.
The downside is one could conceivably mix different architecture's cpu
nodes or have typos in the compatible string. The latter problem pretty
much exists for every schema.
Acked-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Rob Herring [Wed, 3 Jul 2019 20:17:06 +0000 (14:17 -0600)]
dt-bindings: Ensure child nodes are of type 'object'
Properties which are child node definitions need to have an explict
type. Otherwise, a matching (DT) property can silently match when an
error is desired. Fix this up tree-wide. Once this is fixed, the
meta-schema will enforce this on any child node definitions.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-spi@vger.kernel.org
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Brian Norris [Thu, 18 Jul 2019 01:57:12 +0000 (18:57 -0700)]
mac80211: don't warn about CW params when not using them
ieee80211_set_wmm_default() normally sets up the initial CW min/max for
each queue, except that it skips doing this if the driver doesn't
support ->conf_tx. We still end up calling drv_conf_tx() in some cases
(e.g., ieee80211_reconfig()), which also still won't do anything
useful...except it complains here about the invalid CW parameters.
Let's just skip the WARN if we weren't going to do anything useful with
the parameters.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20190718015712.197499-1-briannorris@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Lorenzo Bianconi [Tue, 2 Jul 2019 22:29:47 +0000 (00:29 +0200)]
mac80211: fix possible memory leak in ieee80211_assign_beacon
Free new beacon_data in ieee80211_assign_beacon whenever
ieee80211_assign_beacon fails
Fixes:
8860020e0be1 ("cfg80211: restructure AP/GO mode API")
Fixes:
bc847970f432 ("mac80211: support FTM responder configuration/statistic")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/770285772543c9fca33777bb4ad4760239e56256.1562105631.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John Crispin [Thu, 27 Jun 2019 09:58:32 +0000 (11:58 +0200)]
nl80211: fix NL80211_HE_MAX_CAPABILITY_LEN
NL80211_HE_MAX_CAPABILITY_LEN has changed between D2.0 and D4.0. It is now
MAC (6) + PHY (11) + MCS (12) + PPE (25) = 54.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190627095832.19445-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 25 Jun 2019 08:04:51 +0000 (10:04 +0200)]
nl80211: fix VENDOR_CMD_RAW_DATA
Since ERR_PTR() is an inline, not a macro, just open-code it
here so it's usable as an initializer, fixing the build in
brcmfmac.
Reported-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Fixes:
901bb9891855 ("nl80211: require and validate vendor command policy")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 25 Jun 2019 08:04:51 +0000 (10:04 +0200)]
wireless: fix nl80211 vendor commands
In my previous commit to validate a policy I neglected to
actually add one to the few drivers using vendor commands,
fix that now.
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Fixes:
901bb9891855 ("nl80211: require and validate vendor command policy")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Linus Torvalds [Sat, 20 Jul 2019 19:22:30 +0000 (12:22 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull more input updates from Dmitry Torokhov:
- Apple SPI keyboard and trackpad driver for newer Macs
- ALPS driver will ignore trackpoint-only devices to give the
trackpoint driver a chance to handle them properly
- another Lenovo is switched over to SMbus from PS/2
- assorted driver fixups.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: alps - fix a mismatch between a condition check and its comment
Input: psmouse - fix build error of multiple definition
Input: applespi - remove set but not used variables 'sts'
Input: add Apple SPI keyboard and trackpad driver
Input: alps - don't handle ALPS cs19 trackpoint-only device
Input: hyperv-keyboard - remove dependencies on PAGE_SIZE for ring buffer
Input: adp5589 - initialize GPIO controller parent device
Input: iforce - remove empty multiline comments
Input: synaptics - fix misuse of strlcpy
Input: auo-pixcir-ts - switch to using devm_add_action_or_reset()
Input: gtco - bounds check collection indent level
Input: mtk-pmic-keys - add of_node_put() before return
Input: sun4i-lradc-keys - add of_node_put() before return
Input: synaptics - whitelist Lenovo T580 SMBus intertouch
Thomas Voegtle [Sat, 20 Jul 2019 17:01:22 +0000 (19:01 +0200)]
r8169: fix RTL8168g PHY init
This fixes a copy&paste error in the original patch. Setting the wrong
register resulted in massive packet loss on some systems.
Fixes:
a2928d28643e ("r8169: use paged versions of phylib MDIO access functions")
Tested-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 20 Jul 2019 19:09:52 +0000 (12:09 -0700)]
Merge tag 'dma-mapping-5.3-1' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"Fix various regressions:
- force unencrypted dma-coherent buffers if encryption bit can't fit
into the dma coherent mask (Tom Lendacky)
- avoid limiting request size if swiotlb is not used (me)
- fix swiotlb handling in dma_direct_sync_sg_for_cpu/device (Fugang
Duan)"
* tag 'dma-mapping-5.3-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-direct: correct the physical addr in dma_direct_sync_sg_for_cpu/device
dma-direct: only limit the mapping size if swiotlb could be used
dma-mapping: add a dma_addressing_limited helper
dma-direct: Force unencrypted DMA under SME for certain DMA masks