Haiying Wang [Fri, 3 Oct 2008 15:48:03 +0000 (11:48 -0400)]
Remove redundant #define for MPC8536DS
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Haiying Wang [Fri, 3 Oct 2008 15:47:30 +0000 (11:47 -0400)]
Add ID EEPROM support for MPC8572DS
The ID EEPROM on MPC8572DS board locates on I2C bus 1. Its the storage for
system information like mac addresses etc. This patch enables it.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Haiying Wang [Fri, 3 Oct 2008 15:46:59 +0000 (11:46 -0400)]
Minor fixes for I2C address on MPC8572DS
MPC8572DS has two i2c buses. This patch moves the DDR SPD_EEPROM to i2c bus 1
according to the board spec, and adds the 2nd i2c bus offset.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Jason Jin [Sat, 27 Sep 2008 06:40:57 +0000 (14:40 +0800)]
Fix the incorrect DDR clk freq reporting on 8536DS
On 8536DS board, When the DDR clk is set async mode(SW3[6:8] != 111),
The display is still sync mode DDR freq. This patch try to fix
this. The display DDR freq is now the actual freq in both
sync and async mode.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Kumar Gala [Tue, 7 Oct 2008 15:28:46 +0000 (10:28 -0500)]
85xx: Remove setting of *cache-line-size in device trees
ePAPR says if the *cache-block-size is the same as *cache-line-size
than we don't need the *cache-line-size property.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Stefan Roese [Mon, 22 Sep 2008 14:10:43 +0000 (16:10 +0200)]
ppc4xx: Canyonlands: Remove unnecessary FDT warning upon DTB fixup
Depending on the configuration jumper "SATA SELECT", U-Boot disabled
either one PCIe node or the SATA node in the device tree blob. This
patch removes the unnecessary and even confusing warning, when the node
is not found at all.
Signed-off-by: Stefan Roese <sr@denx.de>
Remy Bohmer [Fri, 19 Sep 2008 11:30:06 +0000 (13:30 +0200)]
Add missing device types to dev_print() in part.c
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Wolfgang Denk [Mon, 22 Sep 2008 20:23:06 +0000 (22:23 +0200)]
Fix DPRAM memory leak when CFG_ALLOC_DPRAM is defined, which
eventually leads to a machine check. This change assures that DPRAM
is allocated only once in that case.
Signed-off-by: Gary Jennejohn <garyj@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Laurent Pinchart [Wed, 17 Sep 2008 15:57:34 +0000 (17:57 +0200)]
Fix Spartan-3 definitions.
A few Spartan-3 definitions erroneously use Spartan-3E size
constants. This patch fixes them.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Laurent Pinchart [Wed, 17 Sep 2008 15:41:58 +0000 (17:41 +0200)]
Remove duplicate Spartan-3E definition.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Anatolij Gustschin [Wed, 17 Sep 2008 11:46:17 +0000 (13:46 +0200)]
socrates: change default mtest address range
Running mtest command on socrates without specifying
an address range crashes the board. This patch changes
default mtest address range to prevent this behavior.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Anatolij Gustschin [Wed, 17 Sep 2008 10:34:45 +0000 (12:34 +0200)]
socrates: fix crash after relocation
Currently U-Boot crashes after relocation to RAM.
Changing the CPO value of the DDR SDRAM TIMING_CFG_2
register to READ_LAT + 1 (to the value it was before
conversion of socrates to new DDR code) fixes the
problem.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Anatolij Gustschin [Wed, 17 Sep 2008 09:45:51 +0000 (11:45 +0200)]
socrates: fix SPD EEPROM address
Commit
be0bd8234b9777ecd63c4c686f72af070d886517
changed SPD EEPROM address to 0x51 and DDR SDRAM
detection stopped working. Change this address
back to 0x50.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Wolfgang Denk [Sun, 21 Sep 2008 20:36:23 +0000 (22:36 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Nobuhiro Iwamatsu [Thu, 18 Sep 2008 10:34:36 +0000 (19:34 +0900)]
sh: Fix compile warning
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Thu, 18 Sep 2008 10:04:26 +0000 (19:04 +0900)]
sh: Add support watchdog for SH4A core
Add support watchdog for SH4A core (SH7763, SH7780 and SH7785).
And fix some compile warning.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Wed, 17 Sep 2008 02:45:26 +0000 (11:45 +0900)]
sh: Fix typo in SH serial driver
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Wed, 17 Sep 2008 02:08:36 +0000 (11:08 +0900)]
sh: Add support any page size and empty_zero_page to SH Linux uImage
Old U-Boot supported 4KB page size only. If this version, Linux
kernel can not get command line from U-Boot.
SH Linux kernel can change page size and empty_zero_page.
This patch support this function and fix promlem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Thu, 28 Aug 2008 04:40:52 +0000 (13:40 +0900)]
sh: rsk7203: Add support pkt_data_pull and pkt_data_push function
Add function of smc911x, pkt_data_pull and pkt_data_push.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Wolfgang Denk [Thu, 18 Sep 2008 11:57:32 +0000 (13:57 +0200)]
ADS5121: fix typo in "rootpath" default setting
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Wed, 17 Sep 2008 08:17:55 +0000 (10:17 +0200)]
Coding style cleanup; update CHANEGLOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
Peter Tyser [Tue, 16 Sep 2008 15:04:47 +0000 (10:04 -0500)]
Support for multiple SGMII/TBI interfaces for TSEC ethernet
Fix TBI PHY accesses to use the proper offset in CPU register space. The
previous code would incorrectly access the TBI PHY by reading/writing to CPU
register space at the same location as would be used to access external PHYs.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Wolfgang Denk [Tue, 16 Sep 2008 16:02:19 +0000 (18:02 +0200)]
TQM8xx: Fix CFI flash driver support for all TQM8xx based boards
After switching to using the CFI flash driver, the correct remapping
of the flash banks was forgotten.
Also, some boards were not adapted, and the old legacy flash driver
was not removed yet.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 13 Sep 2008 22:59:35 +0000 (00:59 +0200)]
Prepare v2008.10-rc2
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 13 Sep 2008 00:23:05 +0000 (02:23 +0200)]
Coding style cleanup, update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
Peter Tyser [Wed, 10 Sep 2008 14:18:34 +0000 (09:18 -0500)]
Update mailing list email and archive addresses
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
u-boot@bugs.denx.de [Thu, 11 Sep 2008 13:40:01 +0000 (15:40 +0200)]
85xx: socrates: autoprobe Lime chip
This patch is an attempt to implement autoprobing for the Lime
presence on the bus.
Configure GPCM for Lime CS2 and try to access chip ID registers.
Second read atempt delivers register values if the chip is present.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
u-boot@bugs.denx.de [Thu, 11 Sep 2008 13:40:01 +0000 (15:40 +0200)]
85xx: socrates: Add support for new image format.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Nobuhiro Iwamatsu [Thu, 11 Sep 2008 08:28:18 +0000 (17:28 +0900)]
sh: Fix compile error for r2dplus
netdev.h was not include by r2dplus.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Heiko Schocher [Thu, 11 Sep 2008 06:11:23 +0000 (08:11 +0200)]
powerpc: Fix bootm to boot up again with a Ramdisk
Commit
2a1a2cb6 didnt remove the dummy mem reservation in fdt_chosen,
and this stopped Linux from booting with a Ramdisk. This patch fixes
this, by deleting the useless dummy mem reservation.
When booting with a Ramdisk, a fix offset FDT_RAMDISK_OVERHEAD is now
added to of_size, so we dont need anymore a dummy mem reservation.
I measured the value of FDT_RAMDISK_OVERHEAD on a MPC8270 based
system (=0x44 bytes) and rounded it up to 0x80).
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Luigi 'Comio' Mantellini [Mon, 8 Sep 2008 00:46:13 +0000 (02:46 +0200)]
Add support for LZMA uncompression algorithm.
Signed-off-by: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Wolfgang Denk [Fri, 12 Sep 2008 23:45:56 +0000 (01:45 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-nand-flash
Anton Vorontsov [Fri, 27 Jun 2008 19:04:20 +0000 (23:04 +0400)]
fsl_elbc_nand: ecclayout cleanups
This patch deletes oobavail assignments, they're calculated by the nand
core code in nand_scan_tail, plus current oobavail values are wrong for
the LP NANDs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Anton Vorontsov [Fri, 27 Jun 2008 19:04:13 +0000 (23:04 +0400)]
fsl_elbc_nand: implement support for flash-based BBT
This patch implements support for flash-based BBT for chips working
through ELBC NAND controller, so that NAND core will not have to re-scan
for bad blocks on every boot.
Because ELBC controller may provide HW-generated ECCs we should adjust
bbt pattern and bbt version positions in the OOB free area.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Anton Vorontsov [Fri, 27 Jun 2008 19:04:04 +0000 (23:04 +0400)]
fsl_elbc_nand: fix OOB workability for large page NAND chips
For large page chips, nand_bbt is looking into OOB area, and checking
for "0xff 0xff" pattern at OOB offset 0. That is, two bytes should be
reserved for bbt means.
But ELBC driver is specifying ecclayout so that oobfree area starts at
offset 1, so only one byte left for the bbt purposes.
This causes problems with any OOB users, namely JFFS2: after first mount
JFFS2 will fill all OOBs with "erased marker", so OOBs will contain:
OOB Data: ff 19 85 20 03 00 ff ff ff 00 00 08 ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
And on the next boot, NAND core will rescan for bad blocks, then will
see "0xff 0x19" pattern, and will mark all blocks as bad ones.
To fix the issue we should implement our own bad block pattern: just one
byte at OOB start. Though, this will work only for x8 chips. For x16
chips two bytes must be checked. Since ELBC driver does not support x16
NANDs (yet), we're safe for now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Wolfgang Denk [Fri, 12 Sep 2008 14:14:28 +0000 (16:14 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
Wolfgang Denk [Fri, 12 Sep 2008 14:13:12 +0000 (16:13 +0200)]
Merge branch 'Makefile-next' of git://git.denx.de/u-boot-arm
Wolfgang Denk [Fri, 12 Sep 2008 13:24:54 +0000 (15:24 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
Wolfgang Denk [Fri, 12 Sep 2008 13:23:20 +0000 (15:23 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
Wolfgang Denk [Fri, 12 Sep 2008 11:52:21 +0000 (13:52 +0200)]
MPC512x: reduce timeout waiting for Ethernet autonegotiation to 2.5s
Signed-off-by: Wolfgang Denk <wd@denx.de>
Stefan Roese [Thu, 11 Sep 2008 11:05:56 +0000 (13:05 +0200)]
ppc4xx: Enable device tree (FDT) support in zeus board port
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Wed, 10 Sep 2008 14:53:47 +0000 (16:53 +0200)]
ppc4xx: Fix SDRAM inititialization of multiple 405 based board ports
This patch fixes a problem introdiced with patch
bbeff30c [ppc4xx: Remove superfluous dram_init() call or replace it by
initdram()].
The boards affected are:
- PCI405
- PPChameleonEVB
- quad100hd
- taihu
- zeus
Signed-off-by: Stefan Roese <sr@denx.de>
Ricardo Ribalda Delgado [Thu, 11 Sep 2008 23:41:26 +0000 (19:41 -0400)]
ppc4xx: Add .gitignore file to xilinx-ppc440 boards
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
Ricardo Ribalda Delgado [Thu, 11 Sep 2008 23:41:25 +0000 (19:41 -0400)]
ppc4xx: Fix compilation of v5fx30teval_flash
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
Ricardo Ribalda Delgado [Wed, 10 Sep 2008 21:44:30 +0000 (17:44 -0400)]
ppc4xx: Fix in-tree build for ppc440-generic boards
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 12 Sep 2008 00:20:47 +0000 (02:20 +0200)]
ARM: synchronize mach-types.h with linux 2.6.27-rc6
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jens Scharsig [Fri, 12 Sep 2008 00:20:47 +0000 (02:20 +0200)]
at91rm9200: fix errors with CONFIG_CMD_I2C_TREE
This patch prevents linker error on AT91RM9200 boards, if
CONFIG_CMD_I2_TREE is set.
It implements i2c_set_bus_speed and i2c_get_bus_speed as a dummy function.
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
Hugo Villeneuve [Fri, 12 Sep 2008 00:20:47 +0000 (02:20 +0200)]
ARM DaVinci: Remove duplicate code in cpu/arm926ejs/davinci/dp83848.c
ARM DaVinci: Remove duplicate code in cpu/arm926ejs/davinci/dp83848.c
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Shinya Kuribayashi [Fri, 12 Sep 2008 00:20:46 +0000 (02:20 +0200)]
make: Remove redundant __ARM__ addition when cross-compiling on *BSD
__ARM__ is given by arm_config.mk automatically.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Claudio Scordino [Fri, 12 Sep 2008 00:20:46 +0000 (02:20 +0200)]
Fix MACH_TYPE for the AT91RM9200DK board.
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Andrew Dyer [Fri, 12 Sep 2008 00:20:46 +0000 (02:20 +0200)]
i.mx change get_timer(base) to return time since base
This patch changes get_timer() for i.MX to return the time since
'base' instead of the time since the counter was at zero.
Symptom seen is flash timeout errors when erasing or programming a
sector using the common cfi flash code.
Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
Andrew Dyer [Fri, 12 Sep 2008 00:20:46 +0000 (02:20 +0200)]
i.MX use u-boot baud rate and don't assume UART master clock
1) Change the i.MX serial driver to use the baud rate set in the
u-boot environment
2) don't assume a 16MHz value for PERCLK1 in baud rate calculations
3) don't write a 1 to the RDR bit in the USR2 reg. (bit is not "write
one to clear" like other status bits in the reg.)
Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
Andrew Dyer [Fri, 12 Sep 2008 00:20:46 +0000 (02:20 +0200)]
arm920t fix constant error in start.S
Code in cpu/arm920t/start.S will die with a compilation error if
CONFIG_STACKSIZE + CFG_MALLOC_LEN works out to an invalid constant for
the ARM sub instruction. Change the code so that each is subtracted
independently to avoid the error.
Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
Gururaja Hebbar K R [Fri, 12 Sep 2008 00:20:40 +0000 (02:20 +0200)]
ARM OMAP : Correct Invalid Timer Register Field Declaration in omap1510.h & omap730.h
- Correct Invalid #define of MPUTIM_PTV_MASK for
omap1510 & omap730 register definition
MPUTIM_PTV_MASK is defined as
#define MPUTIM_PTV_MASK (0x7<<PTV_BIT)
while it should have been
#define MPUTIM_PTV_MASK (0x7<<MPUTIM_PTV_BIT)
- Below Patch corrects the same
Signed-off-by: Gururaja Hebbar <gururajakr@sanyo.co.in>
Adrian Filipi [Fri, 18 Jul 2008 15:52:02 +0000 (11:52 -0400)]
Set up SD/MMC OCR as comment describes. i.e. 3.2-3.4v.
Signed-off-by: Adrian Filipi <adrian.filipi@eurotech.com>
Guennadi Liakhovetski [Thu, 28 Aug 2008 10:25:11 +0000 (12:25 +0200)]
i.MX31: document timer precision option
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Magnus Lilja [Fri, 29 Aug 2008 08:36:18 +0000 (10:36 +0200)]
i.MX31: Make the SPI bus and chip select configurable for MC13783
The i.MX31 has three SPI buses and each bus has several chip selects
and the MC13783 chip can be connected to any of these. The current
RTC driver for MC13783 is hardcoded for CSPI2/SS2.
This patch makes make MC13783 SPI bus and chip select configurable
via CONFIG_MC13783_SPI_BUS and CONFIG_MC13783_SPI_CS.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Magnus Lilja [Fri, 29 Aug 2008 08:36:17 +0000 (10:36 +0200)]
i.MX31: Add reset_timer() and modify get_timer_masked().
This patch adds the reset_timer() function (needed by nand_base.c) and
modifies the get_timer_masked() to work in the same way as the omap24xx
function.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:48:09 +0000 (22:48 +0200)]
ap325rxa: remove duplicate CONFIG_FLASH_CFI_DRIVER
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:48:09 +0000 (22:48 +0200)]
bootm arm/avr32/blackfin/microblaze/nios2/sh: remove no more need 'error' label
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:48:06 +0000 (22:48 +0200)]
rename CFG_ENV macros to CONFIG_ENV
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:48:05 +0000 (22:48 +0200)]
nvedit: rename error comment to CONFIG_ENV_IS_IN_
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:48:05 +0000 (22:48 +0200)]
cmd_mem: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:48:05 +0000 (22:48 +0200)]
move cmd_get_data_size to command.c
add CMD_DATA_SIZE macro to enable it
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:48:04 +0000 (22:48 +0200)]
env_flash: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:48:04 +0000 (22:48 +0200)]
rename CFG_ENV_IS_IN_FLASH in CONFIG_ENV_IS_IN_FLASH
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:48:03 +0000 (22:48 +0200)]
cleanup use of CFG_ENV_IS_IN_FLASH
- #if CFG_ENV_IS_IN_FLASH
- #if (CFG_ENV_IS_IN_FLASH == 1)
- #define CFG_ENV_IS_IN_FLASH 0
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:48:01 +0000 (22:48 +0200)]
rename environment.c in env_embedded.c to reflect is functionality
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:48:01 +0000 (22:48 +0200)]
env_nowhere: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:48:00 +0000 (22:48 +0200)]
rename CFG_ENV_IS_NOWHERE in CONFIG_ENV_IS_NOWHERE
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:48:00 +0000 (22:48 +0200)]
env_sf: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:48:00 +0000 (22:48 +0200)]
rename CFG_ENV_IS_IN_SPI_FLASH in CONFIG_ENV_IS_IN_SPI_FLASH
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:48:00 +0000 (22:48 +0200)]
env_onenand: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:47:59 +0000 (22:47 +0200)]
rename CFG_ENV_IS_IN_ONENAND in CONFIG_ENV_IS_IN_ONENAND
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:47:59 +0000 (22:47 +0200)]
env_nvram: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:47:59 +0000 (22:47 +0200)]
rename CFG_ENV_IS_IN_NVRAM in CONFIG_ENV_IS_IN_NVRAM
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:47:59 +0000 (22:47 +0200)]
env_nand: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:47:58 +0000 (22:47 +0200)]
rename CFG_ENV_IS_IN_NAND in CONFIG_ENV_IS_IN_NAND
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:47:58 +0000 (22:47 +0200)]
env_dataflash: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:47:58 +0000 (22:47 +0200)]
rename CFG_ENV_IS_IN_DATAFLASH in CONFIG_ENV_IS_IN_DATAFLASH
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 10 Sep 2008 20:47:52 +0000 (22:47 +0200)]
cmd_eeprom: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 5 Sep 2008 07:19:54 +0000 (09:19 +0200)]
env_eeprom: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 5 Sep 2008 07:19:30 +0000 (09:19 +0200)]
rename CFG_ENV_IS_IN_EEPROM in CONFIG_ENV_IS_IN_EEPROM
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 30 Aug 2008 21:54:58 +0000 (23:54 +0200)]
cmd_mac: Move conditional compilation to Makefile
finish remaning CFG_ID_EEPROM in CONFIG_ID_EEPROM
start in commit
ad8f8687b78c3e917b173f038926695383c55555
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 30 Aug 2008 21:47:41 +0000 (23:47 +0200)]
cmd_fdc: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 30 Aug 2008 21:47:38 +0000 (23:47 +0200)]
common/Makefile: add core command section
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 30 Aug 2008 21:29:57 +0000 (23:29 +0200)]
cmd_vfd: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Scott Wood [Wed, 10 Sep 2008 16:48:49 +0000 (11:48 -0500)]
delta, zylonite: Update nand_oobinfo to nand_ecclayout.
This is part of the switch to newer upstream MTD code.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Hugo Villeneuve [Sat, 30 Aug 2008 21:06:55 +0000 (17:06 -0400)]
ARM DaVinci: Fix broken HW ECC for large page NAND.
Based on original patch by Bernard Blackham <bernard@largestprime.net>
U-boot's HW ECC support for large page NAND on Davinci is completely
broken. Some kernels, such as the 2.6.10 one supported by
MontaVista for DaVinci, rely upon this broken behaviour as they
share the same code for ECCs. In the existing scheme, error
detection *might* work on large page, but error correction
definitely does not. Small page ECC correction works, but the
format is not compatible with the mainline git kernel.
This patch adds ECC code that matches what is currently in the
Davinci git repository (since NAND support was added in 2.6.24).
This makes the ECC and OOB layout written by u-boot compatible with
Linux for both small page and large page devices and fixes ECC
correction for large page devices.
The old behaviour can be restored by defining the macro
CFG_DAVINCI_BROKEN_ECC, which is undefined by default.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Acked-by: Sergey Kubushyn <ksi@koi8.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Heiko Schocher [Wed, 10 Sep 2008 09:15:28 +0000 (11:15 +0200)]
muas3001: update BR4 settings
Also set up the port pins for using I2C.
Signed-off-by: Heiko Schocher <hs@denx.de>
Petri Lehtinen [Wed, 10 Sep 2008 06:43:49 +0000 (09:43 +0300)]
autoscr: Fix one-character lines and non-newline terminated scripts
When not using hush, the autoscr command now executes lines that are
only one character long. It also runs the last line of scripts even if
it does not end in a newline.
Signed-off-by: Petri Lehtinen <petri.lehtinen@inoi.fi>
Victor Gallardo [Tue, 9 Sep 2008 22:13:29 +0000 (15:13 -0700)]
ppc4xx: Allow DTT_I2C_DEV_CODE configured by CFG_I2C_DTT_ADDR
On AMCC Arches board DTT_I2C_DEV_CODE is different then canyonlands
and glacier.
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Wolfgang Denk [Wed, 10 Sep 2008 09:07:35 +0000 (11:07 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Heiko Schocher [Mon, 8 Sep 2008 08:21:11 +0000 (10:21 +0200)]
muas3001: added support for the LM75 sensor.
Signed-off-by: Heiko Schocher <hs@denx.de>
Heiko Schocher [Mon, 8 Sep 2008 08:20:19 +0000 (10:20 +0200)]
muas3001: activate WDT for the muas3001 board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Heiko Schocher [Mon, 8 Sep 2008 08:19:36 +0000 (10:19 +0200)]
muas3001: added 64MB SDRAM autodetection.
Signed-off-by: Heiko Schocher <hs@denx.de>
Andrew Klossner [Thu, 21 Aug 2008 14:12:26 +0000 (07:12 -0700)]
Fix printf errors under -DDEBUG
Fix printf format-string/arg mismatches under -DDEBUG.
These warnings occur with DEBUG defined for a platform using
cpu/mpc85xx. Users of other architectures can unearth similar
problems by adding the line "CFLAGS += -DDEBUG=1" in config.mk right
after "CFLAGS += $(call cc-option,-fno-stack-protector)".
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Wolfgang Denk [Tue, 9 Sep 2008 21:59:11 +0000 (23:59 +0200)]
Merge branch 'master' of ssh://10.10.0.7/home/wd/git/u-boot/master
Wolfgang Denk [Tue, 9 Sep 2008 21:55:18 +0000 (23:55 +0200)]
Update CHANGELOG, prepare 2008-10-rc1 release
Signed-off-by: Wolfgang Denk <wd@denx.de>
Kumar Gala [Mon, 8 Sep 2008 13:51:29 +0000 (08:51 -0500)]
85xx: Ensure timebase is zero on secondary cores
The e500um says the timebase is volatile out of reset. To ensure
TB sync works we need to make sure its zero.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
projects / platform / kernel / u-boot.git / log