arm64: dts: qcom: sdm845: Pad addresses to 8 hex digits

Some addresses were 7-hex-digits long, or less. Fix that.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230102094642.74254-10-konrad.dybcio@linaro.org

arm64: dts: qcom: sm6350: Pad addresses to 8 hex digits

Some addresses were 7-hex-digits long, or less. Fix that.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230102094642.74254-9-konrad.dybcio@linaro.org

arm64: dts: qcom: sm8150: Pad addresses to 8 hex digits

Some addresses were 7-hex-digits long, or less. Fix that.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230102094642.74254-8-konrad.dybcio@linaro.org

arm64: dts: qcom: sc8280xp: Pad addresses to 8 hex digits

Some addresses were 7-hex-digits long, or less. Fix that.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230102094642.74254-7-konrad.dybcio@linaro.org

arm64: dts: qcom: ipq6018: Use lowercase hex

One value escaped my previous lowercase hexification. Take care of it.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230102094642.74254-6-konrad.dybcio@linaro.org

arm64: dts: qcom: ipq6018: Add/remove some newlines

Some lines were broken very aggresively, presumably to fit under 80 chars
and some places could have used a newline, particularly between subsequent
nodes. Address all that and remove redundant comments near PCIe ranges
while at it so as not to exceed 100 chars needlessly.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230102094642.74254-5-konrad.dybcio@linaro.org

arm64: dts: qcom: ipq6018: Sort nodes properly

Order nodes by unit address if one exists and alphabetically otherwise.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230102094642.74254-4-konrad.dybcio@linaro.org

arm64: dts: qcom: ipq6018: Fix up indentation

The dwc3 subnode was indented using spaces for some reason and other
properties were not exactly properly indented. Fix it.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230102094642.74254-3-konrad.dybcio@linaro.org

arm64: dts: qcom: ipq6018: Pad addresses to 8 hex digits

Some addresses were 7-hex-digits long, or less. Fix that.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230102094642.74254-2-konrad.dybcio@linaro.org

arm64: dts: qcom: sm8550-mtp: Add PCIe PHYs and controllers nodes

Enable PCIe controllers and PHYs nodes on SM8550 MTP board.

Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230118230526.1499328-3-abel.vesa@linaro.org

arm64: dts: qcom: sm8550: Add PCIe PHYs and controllers nodes

Add PCIe controllers and PHY nodes.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230118230526.1499328-2-abel.vesa@linaro.org

arm64: dts: qcom: sm8550-mtp: enable adsp, cdsp & mdss

Add the aDSP, cDSP and MPSS firmware and "Devicetree" firmware paths
for the SM8550 MTP platform.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221115-topic-sm8550-upstream-dts-remoteproc-v3-3-815a1753de34@linaro.org

arm64: dts: qcom: sm8550: add adsp, cdsp & mdss nodes

This adds support for the aDSP, cDSP and MPSS Subsystems found in
the SM8550 SoC.

The aDSP, cDSP and MPSS needs:
- smp2p nodes to get event back from the subsystems
- remoteproc nodes with glink-edge subnodes providing all needed
  resources to start and run the subsystems

In addition, the MPSS Subsystem needs a rmtfs_mem dedicated
memory zone.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221115-topic-sm8550-upstream-dts-remoteproc-v3-2-815a1753de34@linaro.org

arm64: dts: qcom: sm8550: Add interconnect path to SCM node

Add the interconnect path to SCM dts node.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221115-topic-sm8550-upstream-dts-remoteproc-v3-1-815a1753de34@linaro.org

arm64: dts: qcom: sm8550-mtp: add DSI panel

Add nodes for the Visionox VTDR6130 found on the SM8550-MTP
device.

TLMM states are also added for the Panel reset GPIO and
Tearing Effect signal for when the panel is running in
DSI Command mode.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230104-topic-sm8550-upstream-dts-display-v4-3-1729cfc0e5db@linaro.org

arm64: dts: qcom: sm8550-mtp: enable display hardware

Enable MDSS/DPU/DSI0 on SM8550-MTP device.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230104-topic-sm8550-upstream-dts-display-v4-2-1729cfc0e5db@linaro.org

arm64: dts: qcom: sm8550: add display hardware devices

Add devices tree nodes describing display hardware on SM8550:
- Display Clock Controller
- MDSS
- MDP
- two DSI controllers and DSI PHYs

This does not provide support for DP controllers present on the SM8550.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230104-topic-sm8550-upstream-dts-display-v4-1-1729cfc0e5db@linaro.org

Merge branch '20230103-topic-sm8550-upstream-dispcc-v3-1-8a03d348c572@linaro.org' into HEAD

Merge the DT binding in order to get the dispcc include file.

dt-bindings: clock: document SM8550 DISPCC clock controller

Document device tree bindings for display clock controller for
Qualcomm SM8550 SoC.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230103-topic-sm8550-upstream-dispcc-v3-1-8a03d348c572@linaro.org

arm64: dts: qcom: sm8550: fix xo clock source in cpufreq-hw node

Currently, available frequencies for all CPUs are appearing as 2x
of the actual frequencies. Use xo clock source as bi_tcxo in the
cpufreq-hw node to fix this.

Signed-off-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230117093533.3710000-1-quic_pkondeti@quicinc.com

arm64: dts: qcom: msm8916-samsung-j5-common: Add MUIC support

The MUIC installed is a part of SM5703 MFD, and it seems to work
the same as the SM5502 MUIC unit.

Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
[Apply for msm8916-samsung-j5x]
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230106143051.547302-1-linmengbo0689@protonmail.com

arm64: dts: qcom: msm8916-samsung-j5-common: Add Hall sensor

Samsung Galaxy J5 2015 and 2016 have a Hall sensor on GPIO pin 52.
Add GPIO Hall sensor for them.

Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230106143037.547248-1-linmengbo0689@protonmail.com

arm64: dts: qcom: msm8916-samsung-j5-common: Add new device trees

After moving msm8916-samsung-j5.dts to msm8916-samsung-j5-common.dtsi,
Add new J5 2016 device tree.

[Add j5x device tree]

Co-developed-by: Josef W Menad <JosefWMenad@protonmail.ch>
Signed-off-by: Josef W Menad <JosefWMenad@protonmail.ch>
[Use &pm8916_usbin as USB extcon and add chassis-type for j5x]
Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
[Use common init device tree]
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230106143024.547194-1-linmengbo0689@protonmail.com

arm64: dts: qcom: msm8916-samsung-j5-common: Add initial common device tree

The smartphones below are using the MSM8916 SoC,
which are released in 2015-2016:

Samsung Galaxy J5 2015 (SM-J500*)
Samsung Galaxy J5 2016 (SM-J510*)

Move msm8916-samsung-j5.dts to msm8916-samsung-j5-common.dtsi, and add
a common device tree for with initial support for:

- GPIO keys
- SDHCI (internal and external storage)
- USB Device Mode
- UART (on USB connector via the SM5703 MUIC)
- WCNSS (WiFi/BT)
- Regulators

The two devices (all other variants of J5 released in 2015 and J5X
released in 2016) are very similar, with some differences in display and
GPIO pins. The common parts are shared in msm8916-samsung-j5-common.dtsi
to reduce duplication.

This patch rewrites J5 2015 devices, later patches will add support for
other models.

Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230106143010.547140-1-linmengbo0689@protonmail.com

arm64: dts: qcom: sm7225-fairphone-fp4: enable IPA

IPA is used for mobile data. Enable it.

Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230104193759.3286014-3-elder@linaro.org

arm64: dts: qcom: sm6350: add IPA node

IPA is used for mobile data. Add a node describing it.

Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230104193759.3286014-2-elder@linaro.org

arm64: dts: qcom: sm6350: Set up DDR & L3 scaling

Add the CPU OPP tables including core frequency and L3 bus frequency.
The L3 throughput values were chosen by studying the frequencies
available in HW LUT and picking the highest one that's less than the
CPU frequency. DDR clock rates come from the vendor kernel.

Available values from the HW LUT:
300000000
556800000
652800000
806400000
844800000
940800000
1132800000
1209600000
1286400000
1401600000
1459200000

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230104171643.1004054-3-konrad.dybcio@linaro.org

arm64: dts: qcom: sm6350: Add OSM L3 node

Enable the OSM block responsible for scaling the L3 cache.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230104171643.1004054-2-konrad.dybcio@linaro.org

arm64: dts: qcom: qcs404: specify per-sensor calibration cells

Specify pre-parsed per-sensor calibration nvmem cells in the tsens
device node rather than parsing the whole data blob in the driver.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230101194034.831222-19-dmitry.baryshkov@linaro.org

arm64: dts: qcom: msm8976: specify per-sensor calibration cells

Specify pre-parsed per-sensor calibration nvmem cells in the tsens
device node rather than parsing the whole data blob in the driver.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230101194034.831222-18-dmitry.baryshkov@linaro.org

arm64: dts: qcom: msm8916: specify per-sensor calibration cells

Specify pre-parsed per-sensor calibration nvmem cells in the tsens
device node rather than parsing the whole data blob in the driver.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230101194034.831222-17-dmitry.baryshkov@linaro.org

arm64: dts: qcom: msm8956: use SoC-specific compat for tsens

The slope values used during tsens calibration differ between msm8976
and msm8956 SoCs. Use SoC-specific compat value for the msm8956 SoC.

Fixes: 0484d3ce0902 ("arm64: dts: qcom: Add DTS for MSM8976 and MSM8956 SoCs")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230101194034.831222-16-dmitry.baryshkov@linaro.org

arm64: dts: qcom: use qcom,gsi-loader for IPA

Depending on the platform, either the modem or the AP must load GSI
firmware for IPA before it can be used.  To date, this has been
indicated by the presence or absence of a "modem-init" property.

That mechanism has been deprecated.  Instead, we indicate how GSI
firmware should be loaded by the value of the "qcom,gsi-loader"
property.

Update all arm64 platforms that use IPA to use the "qcom,gsi-loader"
property to specify how the GSI firmware is loaded.

Update the affected nodes so the status property is last.

Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
[bjorn: Moved sc7280 change herobrine-lte-sku]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221231002716.2367375-3-elder@linaro.org

arm64: dts: qcom: sc7280-idp: add amp pin config function

Bindings expect each pin config to come with a "function" property:

  sc7280-crd-r3.dtb: pinctrl@f100000: amp-en-state: 'oneOf' conditional failed, one must be fixed:
    'function' is a required property
    'bias-pull-down', 'drive-strength', 'pins' do not match any of the regexes: '-pins$', 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221230135645.56401-9-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: msm8916-samsung-a2015: correct motor pinctrl node name

Correct typo in motor pinctrl node name:

  msm8916-samsung-a5u-eur.dtb: pinctrl@1000000: 'motor-en-default-stae' does not match any of the regexes: '-state$', 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221230135645.56401-8-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: msm8992-bullhead: Disable dfps_data_mem

It's disabled on downstream [1] thus not shown on downstream dmesg.

Removing it fixes warnings on v6.1:

[    0.000000] OF: reserved mem: OVERLAP DETECTED!
[    0.000000] dfps_data_mem@3400000 (0x0000000003400000--0x0000000003401000) overlaps with memory@3400000 (0x0000000003400000--0x0000000004600000)

[1] https://android.googlesource.com/kernel/msm.git/+/android-7.0.0_r0.17/arch/arm64/boot/dts/lge/msm8992-bullhead.dtsi#137

Fixes: 976d321f32dc ("arm64: dts: qcom: msm8992: Make the DT an overlay on top of 8994")

Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221226185440.440968-3-pevik@seznam.cz

arm64: dts: qcom: msm8992-bullhead: Fix cont_splash_mem size

Original google firmware reports 12 MiB:
[    0.000000] cma: Found cont_splash_mem@0, memory base 0x0000000003400000, size 12 MiB, limit 0xffffffffffffffff

which is actually 12*1024*1024 = 0xc00000.

This matches the aosp source [1]:
&cont_splash_mem {
reg = <0 0x03400000 0 0xc00000>;
};

Fixes: 3cb6a271f4b0 ("arm64: dts: qcom: msm8992-bullhead: Fix cont_splash_mem mapping")
Fixes: 976d321f32dc ("arm64: dts: qcom: msm8992: Make the DT an overlay on top of 8994")

[1] https://android.googlesource.com/kernel/msm.git/+/android-7.0.0_r0.17/arch/arm64/boot/dts/lge/msm8992-bullhead.dtsi#141

Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221226185440.440968-2-pevik@seznam.cz

Merge tag 'qcom-arm64-fixes-for-6.2' into arm64-for-6.3

Qualcomm ARM64 DTS fixes for 6.2

The cluster idle issue was resolved on SM8250, so the change disabling
the cluster state is being reverted.

Issues where identified with the QMP PHY binding, that would prevent
enablement of Displayport and it was decided not to support the old
binding for the recently introduced SC8280XP, which broke USB. This
adjusts the USB PHY nodes to the new binding. The reset signal for the
first QMP PHY is corrected as well.

The reserved memory map is updated on Xiaomi Mi 4C and Huawei Nexus 6P,
to avoid instabilities caused by use of protected memory regions.
The compatible for the MSM8992 TCSR mutex is corrected as well.

Lastly SDHCI interconnects on SM8350 are corrected to match the
providers #interconnect-cells.

arm64: dts: qcom: sm8350: Use 2 interconnect cells

Use two interconnect cells in order to optionally
support a path tag.

Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230117115712.1054613-1-rfoss@kernel.org

arm64: dts: qcom: sm8350: Add &tlmm gpio-line-names

Add GPIO line names as described by the sm8350-hdk schematic.

Signed-off-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230117112537.1016250-1-rfoss@kernel.org

arm64: dts: qcom: sc8280xp: Define CMA region for CRD and X13s

While booting the CRD, a series of CMA allocation errors can be seen in
the kernel log:

  cma: cma_alloc: reserved: alloc failed, req-size: 128 pages, ret: -12

Growing the CMA region and querying /proc/meminfo indicates that a newly
booted system (currently) uses 64MB CMA.

Define a memory region sufficiently large for the current use cases, to
avoid forcing users to add this themselves, through command line
parameters etc.

While fixing the CRD define the same region for the X13s.

Tested-by: Andrew Halaney <ahalaney@redhat.com> # sc8280xp-lenovo-thinkpad-x13s
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230117184630.2775905-1-quic_bjorande@quicinc.com

arm64: dts: qcom: sc7280: add DP audio to herobrine rt5682 1-mic dtsi

1. Add DisplayPort sound node and lpass_cpu node.

2. Adjust the dai-link order to make the order to
   be consistent with sc7280-herobrine-audio-rt5682-3mic.dtsi.

Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230118011853.1614566-1-judyhsiao@chromium.org

arm64: dts: qcom: sm8250: clean up wcd938x codec node

Clean up the wcd938x codec node somewhat by adding newline separators,
reordering properties and renaming it 'audio-codec'.

Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230103103141.15807-7-johan+linaro@kernel.org

arm64: dts: qcom: sm8450-hdk: move wcd938x codec node

The wcd938x codec is not a memory-mapped device and does not belong
under the soc node.

Move the node to the root node to avoid DT validation failures.

While at it, clean up the node somewhat by reordering properties and
renaming it 'audio-codec'.

Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230103103141.15807-6-johan+linaro@kernel.org

arm64: dts: qcom: sc8280xp-x13s: move wcd938x codec node

The wcd938x codec is not a memory-mapped device and does not belong
under the soc node.

Move the node to the root node to avoid DT validation failures.

While at it, clean up the node somewhat by adding newline separators,
reordering properties and renaming it 'audio-codec'.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230103103141.15807-5-johan+linaro@kernel.org

arm64: dts: qcom: sc8280xp-x13s: move vamacro node

Move the vamacro node to restore the alphabetical sort order.

While at it, add some newline separators to improve readability.

Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230103103141.15807-3-johan+linaro@kernel.org

arm64: dts: qcom: sc8280xp: disable sound nodes

The sound nodes in the SoC dtsi should be disabled by default.

Note that the lpass-tlmm and macro blocks depend on having the board dts
enable the adsp and specifying an appropriate firmware to enable the
q6prm clock controller.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230103103141.15807-2-johan+linaro@kernel.org

arm64: dts: qcom: sc8280xp: drop unused properties from tx-macro

tx-macro does not have children and does not allow address/size cells:

  sc8280xp-crd.dtb: txmacro@3220000: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230118094224.51704-3-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc8280xp: drop bogus clock-controller property

There is no "clock-controller" property:

  sa8295p-adp.dtb: service@2: clock-controller: 'clock-controller' does not match any of the regexes: 'pinctrl-[0-9]+'
    From schema: Documentation/devicetree/bindings/sound/qcom,q6prm.yaml

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230118094224.51704-2-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm8250: drop unused clock-frequency from rx-macro

Neither qcom,sm8250-lpass-rx-macro bindings nor the driver use
"clock-frequency" property.

  sm8250-mtp.dtb: rxmacro@3200000: Unevaluated properties are not allowed ('clock-frequency' was unexpected)

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230118094224.51704-1-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc7180: set ath10k output power calibration string

Add the string to load RF output power table for pazquel360 project.

Signed-off-by: Yunlong Jia <ecs.beijing2022@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230117085212.1.If242b1cd61b2e87e312dd9cf81e20301bae2a5a4@changeid

arm64: dts: qcom: sm6115: Add debug related nodes

Add dtsi nodes related to coresight debug units such
as cti, etm, etr, funnel(s), replicator(s), etc. for
Qualcomm sm6115 SoC.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230116164032.551223-1-bhupesh.sharma@linaro.org

arm64: dts: qcom: sm8350-hdk: Enable lt9611uxc dsi-hdmi bridge

The sm8350-hdk ships with the LT9611 UXC DSI/HDMI bridge chip.

In order to toggle the board to enable the HDMI output,
switch #7 & #8 on the rightmost multi-switch package have
to be toggled to On.

Signed-off-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230117120223.1055225-4-rfoss@kernel.org

arm64: dts: qcom: sm8350-hdk: Enable display & dsi nodes

Enable the display subsystem and the dsi0 output for
the sm8350-hdk board.

Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230117120223.1055225-3-rfoss@kernel.org

arm64: dts: qcom: sm8350: Add display system nodes

Add mdss, mdss_mdp, dsi0, dsi0_phy nodes. With these
nodes the display subsystem is configured to support
one DSI output.

Signed-off-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230117120223.1055225-2-rfoss@kernel.org

arm64: dts: qcom: sm8550-mtp: Add UFS host controller and PHY node

Enable UFS host controller and PHY node on SM8550 MTP board.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230116141000.1831351-2-abel.vesa@linaro.org

arm64: dts: qcom: sm8550: Add UFS host controller and phy nodes

Add UFS host controller and PHY nodes.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230116141000.1831351-1-abel.vesa@linaro.org

arm64: dts: qcom: sdm630-nile: Reserve simplefb memory

Reserve the bit of memory that simplefb uses to ensure it can always
probe.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230116141451.470158-2-konrad.dybcio@linaro.org

arm64: dts: qcom: sdm630-nile: Don't use underscores in node names

Rename the reserved-memory subnodes such that they don't use
undescores.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230116141451.470158-1-konrad.dybcio@linaro.org

arm64: dts: qcom: add data-lanes and link-freuencies into dp_out endpoint

Move data-lanes property from mdss_dp node to dp_out endpoint. Also
add link-frequencies property into dp_out endpoint as well. The last
frequency specified at link-frequencies will be the max link rate
supported by DP.

Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1672163103-31254-2-git-send-email-quic_khsieh@quicinc.com

arm64: dts: qcom: sc7180-trogdor: align DAI children names with DT schema

Bindings expect DAI children to be named "dai-link":

  sc7180-trogdor-coachz-r1.dtb: lpass@62d87000: Unevaluated properties are not allowed ('hdmi@5', 'mi2s@0', 'mi2s@1' were unexpected)

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221227163158.102737-2-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm8350: drop unused dispcc power-domain-names

Display clock controller bindings do not allow power-domain-names:

  sm8350-hdk.dtb: clock-controller@af00000: 'power-domain-names' does not match any of the regexes: 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/clock/qcom,dispcc-sm8x50.yaml

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221227163158.102737-1-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: use UFS symbol clocks provided by PHY

Remove manually created symbol clocks and replace them with clocks
provided by PHY.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221123104443.3415267-5-dmitry.baryshkov@linaro.org

arm64: dts: qcom: sm8350-hdk: enable PCIe devices

Enable PCIe0 and PCIe1 hosts found on SM8350 HDK board.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221118233242.2904088-9-dmitry.baryshkov@linaro.org

arm64: dts: qcom: sm8350: add PCIe devices

Add PCIe0 and PCIe1 (and corresponding PHY) devices found on SM8350
platform. The PCIe0 is a 1-lane Gen3 host, PCIe1 is a 2-lane Gen3 host.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221118233242.2904088-8-dmitry.baryshkov@linaro.org

arm64: dts: qcom: sc8280xp: Use MMCX for all DP controllers

While MDSS_GDSC is a subdomain of MMCX, Linux does not respect this
relationship and sometimes invokes sync_state on the rpmhpd (MMCX)
before the DisplayPort controller has had a chance to probe.

The result when this happens is that the power is lost to the multimedia
subsystem between the probe of msm_drv and the DisplayPort controller -
which results in an irrecoverable state.

While this is an implementation problem, this aligns the power domain
setting of the one DP instance with that of all the others.

Fixes: 57d6ef683a15 ("arm64: dts: qcom: sc8280xp: Define some of the display blocks")
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230112135055.3836555-1-quic_bjorande@quicinc.com

arm64: dts: qcom: sc8280xp-crd: allow vreg_l3b to be disabled

The vreg_l3b supply is used by the eDP, UFS and USB1 PHYs which are now
described by the devicetree so that the regulator no longer needs to be
marked always-on.

Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230112074503.12185-1-johan+linaro@kernel.org

arm64: dts: qcom: sm8450: Add TCSR halt register space

Add TCSR register space and refer it from scm node, so that
it can be used by SCM driver.

Signed-off-by: Mukesh Ojha <quic_mojha@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1673513697-30173-2-git-send-email-quic_mojha@quicinc.com

arm64: dts: qcom: sc8280xp: Vote for CX in USB controllers

Running GCC_USB30_*_MASTER_CLK at 200MHz requires CX at nominal level,
not doing so results in occasional lockups. This was previously hidden
by the fact that the display stack incorrectly voted for CX (instead of
MMCX).

Fixes: 152d1faf1e2f ("arm64: dts: qcom: add SC8280XP platform")
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230112135117.3836655-1-quic_bjorande@quicinc.com

arm64: dts: qcom: sm8250: drop the virtual ipa-virt device

Drop the virtual ipa-virt device. The interconnects it provided are
going to be represented as <&rpmhcc RPMH_IPA_CLK> clock.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230109002935.244320-13-dmitry.baryshkov@linaro.org

arm64: dts: qcom: sm8150: drop the virtual ipa-virt device

Drop the virtual ipa-virt device. The interconnects it provided are
going to be represented as <&rpmhcc RPMH_IPA_CLK> clock.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230109002935.244320-12-dmitry.baryshkov@linaro.org

arm64: dts: qcom: pm7250b: Add BAT_ID vadc channel

Add a node describing the ADC5_BAT_ID_100K_PU channel with the
properties taken from downstream kernel.

Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230106-pm7250b-bat_id-v1-2-82ca8f2db741@fairphone.com

arm64: dts: qcom: msm8916: Add DMA for all I2C controllers

i2c-qup allows using DMA to speed up larger transfers. In msm8916.dtsi
the DMA channels are already assigned to the SPI controllers but
missing for I2C. Add them there as well.

This also fixes confusing errors in dmesg for each I2C controller:
  i2c_qup 78b6000.i2c: tx channel not available

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230107110958.5762-3-stephan@gerhold.net

arm64: dts: qcom: msm8916: Enable blsp_dma by default

Adding the "dmas" to the I2C controllers prevents probing them if
blsp_dma is disabled (infinite probe deferral). Avoid this by enabling
blsp_dma by default - it's an integral part of the SoC that is almost
always used (even if just for UART).

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230107110958.5762-2-stephan@gerhold.net

arm64: dts: qcom: msm8916-gplus-fl8005a: Add flash LED

FL8005A uses Qualcomm GPIO flash LEDs which is compatible with
SGM3140 Flash LED driver. Add it to the device tree.

Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230107133235.139947-1-linmengbo0689@protonmail.com

arm64: dts: qcom: msm8916-gplus-fl8005a: Add touchscreen

FL8005A uses a Focaltech FT5402 touchscreen that is connected to
blsp_i2c5. Add it to the device tree.

Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230107133223.139893-1-linmengbo0689@protonmail.com

arm64: dts: qcom: msm8916-gplus-fl8005a: Add initial device tree

GPLUS FL8005A is a tablet using the MSM8916 SoC released in 2015.

Add a device tree for with initial support for:

- GPIO keys
- GPIO LEDs
- pm8916-vibrator
- SDHCI (internal and external storage)
- USB Device Mode
- UART
- WCNSS (WiFi/BT)
- Regulators

Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230107133210.139839-1-linmengbo0689@protonmail.com

arm64: dts: qcom: msm8996: mark apcs as clock provider

Now as we added the APCS clock controller support, mark apcs device as
clock provider by adding #clock-cells property.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230111191634.2509616-1-dmitry.baryshkov@linaro.org

arm64: dts: qcom: sa8540p-pmics: rename pmic labels

The SA8540P PMICs are named PMM8540. Rename the devicetree source labels
to reflect this.

Reviewed-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Eric Chanudet <echanude@redhat.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230111160335.7175-3-johan+linaro@kernel.org

arm64: dts: qcom: sa8540p-pmics: add missing interrupt include

Add the missing interrupt-controller include which is needed by the RTC
node.

Reviewed-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Eric Chanudet <echanude@redhat.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230111160335.7175-2-johan+linaro@kernel.org

arm64: dts: qcom: sc8280xp-x13s: enable eDP display

Enable the eDP display on MDSS0 DP3, including backlight control.

Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230111133128.31813-1-johan+linaro@kernel.org

arm64: dts: qcom: sa8295-adp: Enable DP instances

The SA8295P ADP has, among other interfaces, six MiniDP connectors which
are connected to MDSS0 DP2 and DP3, and MDSS1 DP0 through DP3.

Enable Display Clock controllers, MDSS instanced, MDPs, DP controllers,
DP PHYs and link them all together.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230111035906.2975494-4-quic_bjorande@quicinc.com

arm64: dts: qcom: sc8280xp-crd: Enable EDP

The SC8280XP CRD has a EDP display on MDSS0 DP3, enable relevant nodes
and link it together with the backlight control.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230111035906.2975494-3-quic_bjorande@quicinc.com

arm64: dts: qcom: sc8280xp: Define some of the display blocks

Define the display clock controllers, the MDSS instances, the DP phys
and connect these together.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230111035906.2975494-2-quic_bjorande@quicinc.com

Revert "dt-bindings: arm: qcom: Add SM6115(P) and Lenovo Tab P11"

This reverts commit 92ad27fb925943d62deaaa659931ce85ddec99c8, as this
was applied to the wrong branch and causes merge conflicts.

arm64: dts: qcom: msm8996-oneplus-common: drop vdda-supply from DSI PHY

14nm DSI PHY has the only supply, vcca. Drop the extra vdda-supply.

Fixes: 5a134c940cd3 ("arm64: dts: qcom: msm8996: add support for oneplus3(t)")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230109042406.312047-1-dmitry.baryshkov@linaro.org

arm64: dts: qcom: sdm845-tama: Add volume up and camera GPIO keys

Tama has four GPIO-wired keys: two for camera focus and shutter /
snapshot, and two more for volume up and down.  As per the comment these
used to not work because the necessary pin bias was missing, which is
now set via pinctrl on pm8998_gpios.

The missing bias has also been added to the existing volume down button,
which receives a node name and label cleanup at the same time to be more
consistent with other DTS and the newly added buttons.  Its deprecated
gpio-key,wakeup property has also been replaced with wakeup-source.

Note that volume up is also available through the usual PON RESIN node,
but unlike other platforms only triggers when the power button is held
down at the same time making it unsuitable to serve as KEY_VOLUMEUP.

Fixes: 30a7f99befc6 ("arm64: dts: qcom: Add support for SONY Xperia XZ2 / XZ2C / XZ3 (Tama platform)")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230109234133.365644-1-marijn.suijten@somainline.org

arm64: dts: qcom: sdm845: make DP node follow the schema

Drop the #clock-cells (probably a leftover from the times before the DP
PHY split)

Fixes: eaac4e55a6f4 ("arm64: dts: qcom: sdm845: add displayport node")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230110042126.702147-1-dmitry.baryshkov@linaro.org

arm64: dts: qcom: msm8998: Use RPM XO

Feed GCC and SDHC_2 with the RPM XO instead of the fixed-clock one.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230110143642.986799-1-konrad.dybcio@linaro.org

arm64: dts: qcom: sm8450: Use GIC-ITS for PCIe0 and PCIe1

Both PCIe0 and PCIe1 controllers are capable of signalling the MSIs
received from endpoint devices to the CPU using GIC-ITS MSI controller.
Add support for it.

Currently, BDF (0:0.0) and BDF (1:0.0) are enabled and with the
msi-map-mask of 0xff00, all the 32 devices under these two busses can
share the same Device ID.

The GIC-ITS MSI implementation provides an advantage over internal MSI
implementation using Locality-specific Peripheral Interrupts (LPI) that
would allow MSIs to be targeted for each CPU core.

It should be noted that the MSIs for BDF (1:0.0) only works with Device
ID of 0x5980 and 0x5a00. Hence, the IDs are swapped.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org> # Xperia 1 IV (WCN6855)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230102105821.28243-4-manivannan.sadhasivam@linaro.org

arm64: dts: qcom: add missing space before {

Add missingh whitespace between node name/label and opening {.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221230140133.57885-2-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: msm8998: get rid of test clock

The test clock apparently it's not used by anyone upstream. Remove it.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221228185237.3111988-17-dmitry.baryshkov@linaro.org

arm64: dts: qcom: sm8450: correct Soundwire wakeup interrupt name

The bindings expect second Soundwire interrupt to be "wakeup" (Linux
driver takes by index):

  sm8450-hdk.dtb: soundwire-controller@33b0000: interrupt-names:1: 'wakeup' was expected

Fixes: 14341e76dbc7 ("arm64: dts: qcom: sm8450: add Soundwire and LPASS")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221223132121.81130-1-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: pm8941-rtc add alarm register

A few descriptions including a qcom,pm8941-rtc describe two reg-names
for the "rtc" and "alarm" register banks, but only one offset.
For consistency with reg-names, add the "alarm" register offset.
No functional change is expected from this.

Signed-off-by: Eric Chanudet <echanude@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221219191000.2570545-5-echanude@redhat.com

arm64: dts: qcom: sa8295p-adp: use sa8540p-pmics

Include the dtsi to use a single pmic descriptions.
Both sa8295p-adp and sa8540p-adp have the same spmi pmic apparently.

Signed-off-by: Eric Chanudet <echanude@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221219191000.2570545-4-echanude@redhat.com

arm64: dts: qcom: sa8450p-pmics: add rtc node

Add the rtc block on the first pmic to enable the rtc for sa8540p-ride.

Signed-off-by: Eric Chanudet <echanude@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221219191000.2570545-3-echanude@redhat.com

arm64: dts: qcom: rename pm8450a dtsi to sa8540p-pmics

pm8450a.dtsi was introduced for the descriptions of pmics used on
sa8540p based boards. Rename the dtsi to make this relationship
explicit.

Signed-off-by: Eric Chanudet <echanude@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221219191000.2570545-2-echanude@redhat.com

arm64: dts: qcom: sm8350: Drop standalone smem node

SM8350 is one of the last SoCs whose DTSI escaped the smem node
conversion. Use the newer memory-node binding instead of a memory *and*
smem node.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221219162618.873117-1-konrad.dybcio@linaro.org

arm64: dts: qcom: sm8450-hdk: add missing PMIC includes

Add includes for PMICs used on the SM8450-HDK. This makes GPIO blocks
and thermal sensors available to the user of the platform.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221217003349.546852-6-dmitry.baryshkov@linaro.org

arm64: dts: qcom: sm8450-hdk: add pmic files

SM8450 HDK features bunch of PMICs, add the PMICs which we have already
upstream files

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221217003349.546852-5-dmitry.baryshkov@linaro.org