drm/i915/psr: Remove useless function calls.

PSR is no longer supported on VLV/CHV so this is just dead code.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180711220050.21809-1-rodrigo.vivi@intel.com

drm/i915/psr: Split sink status into a separate debugfs node

This allows to read i915_edp_psr_status from tests without triggering
any AUX communication. Take this opportunity to move this under the
eDP-1 connector directory as the status we print is of the sink.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Suggested-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705003121.2478-1-dhinakaran.pandiyan@intel.com

drm/i915: Use crtc_state->has_psr instead of CAN_PSR for pipe update

In commit "drm/i915: Wait for PSR exit before checking for vblank
evasion", the idea was to limit the PSR IDLE checks when PSR is
actually supported. While CAN_PSR does do that check, it doesn't
applies on a per-crtc basis. crtc_state->has_psr is a more granular
check that only applies to pipe(s) that have PSR enabled.

Without the has_psr check, we end up waiting on the eDP transcoder's
PSR_STATUS register irrespective of whether the pipe being updated is
driving it or not.

v2: Remove unnecessary parantheses, make checkpatch happy.

v3: Move the has_psr check to intel_psr_wait_for_idle and commit
    message changes (DK).

v4: Derive dev_priv from intel_crtc_state (DK)

v5: Commit message changes to reflect the HW behavior (DK)

Fixes: a608987970b9 ("drm/i915: Wait for PSR exit before checking for vblank evasion")
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Tarun Vyas <tarun.vyas@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712053323.26266-1-tarun.vyas@intel.com

drm/i915/gmbus: Enable burst read

Support for Burst read in HW is added for HDCP2.2 compliance
requirement.

This patch enables the burst read for all the gmbus read of more than
511Bytes, on capable platforms.

v2:
  Extra line is removed.
v3:
  Macro is added for detecting the BURST_READ Support [Jani]
  Runtime detection of the need for burst_read [Jani]
  Calculation enhancement.
v4:
  GMBUS0 reg val is passed from caller [ville]
  Removed a extra var [ville]
  Extra brackets are removed [ville]
  Implemented the handling of 512Bytes Burst Read.
v5:
  Burst read max length is fixed at 767Bytes [Ville]
v6:
  Collecting the received reviewed-by.

Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1530192889-5789-3-git-send-email-ramalingam.c@intel.com

drm/i915/gmbus: Increase the Bytes per Rd/Wr Op

GMBUS HW supports 511Bytes as Max Bytes per single RD/WR op. Instead of
enabling the 511Bytes per RD/WR cycle on legacy platforms for no
absolute ROIs, this change allows the max bytes per op upto 511Bytes
from Gen9 onwards.

v2:
  No Change.
v3:
  Inline function for max_xfer_size and renaming of the macro.[Jani]
v4:
  Extra brackets removed [ville]
  Commit msg is modified.
v5:
  Collecting the Reviewed-By received.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1530192889-5789-2-git-send-email-ramalingam.c@intel.com

drm/i915/selftests: Fixup GuC FW negative test

Since:
0d4b78b3d2c0 ("drm/i915/guc: Assert we have the doorbell before setting it up")

We have asserts in GuC doorbell related functions, which is a good thing.
Unfortunately, we were using those to check whether GuC FW is refusing
to allocate invalid doorbell - which makes the test fail.
Well, it would make the test WARN, except we fumbled cleanup ordering
and eat the BUG_ON instead.
Let's keep the asserts and use the internal implementation in the test.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107186
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712112013.3253-1-chris@chris-wilson.co.uk
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Tidy error handling in i915_gem_init_hw

Let's reorder things so that we can do onion teardown rather than double
goto.

References: b96f6ebfd024 ("drm/i915: Correctly handle error path in i915_gem_init_hw")
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712124810.25241-1-michal.winiarski@intel.com

drm/i915/guc: Skip cleaning up the doorbells on error-before-allocate

If we fail the module load, we may try and cleanup before we even
allocate the GuC clients. KISS in order to try and re-enable
drv_module_reload for BAT.

Testcase: igt/drv_module_reload/basic-reload-inject
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712105830.20390-1-chris@chris-wilson.co.uk

drm/i915: Silence warning for no vlv powercontext

Along a module load error path, we may try to cleanup the powercontext
even before we have allocated it.  Reorganising GT powermanagement is an
 on going process, so for simplicity handle it.

[  522.733832] WARN_ON(!dev_priv->vlv_pctx)
[  522.733986] WARNING: CPU: 1 PID: 3856 at drivers/gpu/drm/i915/intel_pm.c:7350 intel_cleanup_gt_powersave+0x5f/0x70 [i915]
[  522.733991] Modules linked in: i915(+) vgem snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic btusb btrtl btbcm btintel intel_powerclamp coretemp crct10dif_pclmul crc32_pclmul bluetooth snd_hda_codec ghash_clmulni_intel snd_hwdep snd_hda_core ecdh_generic lpc_ich r8169 snd_pcm mii i2c_hid prime_numbers [last unloaded: i915]
[  522.734105] CPU: 1 PID: 3856 Comm: drv_module_relo Tainted: G     U            4.18.0-rc4-CI-CI_DRM_4474+ #1
[  522.734110] Hardware name: \xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff \xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff/DN2820FYK, BIOS FYBYT10H.86A.0059.2017.0607.2130 06/07/2017
[  522.734193] RIP: 0010:intel_cleanup_gt_powersave+0x5f/0x70 [i915]
[  522.734197] Code: 00 74 0d 48 c7 83 68 a6 00 00 00 00 00 00 eb c8 e8 36 6f 37 e1 eb ec 48 c7 c6 c5 7a 3d a0 48 c7 c7 b5 78 3d a0 e8 71 04 e0 e0 <0f> 0b eb aa 0f 1f 00 66 2e 0f 1f 84 00 00 00 00 00 f3 c3 0f 1f 40
[  522.734445] RSP: 0018:ffffc900004f3af0 EFLAGS: 00010282
[  522.734453] RAX: 0000000000000000 RBX: ffff880106360000 RCX: 0000000000000001
[  522.734458] RDX: 0000000080000001 RSI: ffffffff820c65c4 RDI: 00000000ffffffff
[  522.734463] RBP: ffff880106360000 R08: 000000009f79baee R09: 0000000000000000
[  522.734467] R10: 0000000000000000 R11: 0000000000000000 R12: ffff88013b3133f8
[  522.734472] R13: 00000000ffffffed R14: ffff880106360d58 R15: ffff88013b3133f8
[  522.734477] FS:  00007f43f70af980(0000) GS:ffff88013fd00000(0000) knlGS:0000000000000000
[  522.734481] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  522.734486] CR2: 000055a13a787580 CR3: 00000001325e6000 CR4: 00000000001006e0
[  522.734490] Call Trace:
[  522.734595]  intel_modeset_cleanup+0xcf/0x140 [i915]
[  522.734682]  i915_driver_load+0xc85/0x10a0 [i915]
[  522.734694]  ? _raw_spin_unlock_irqrestore+0x4c/0x60
[  522.734703]  ? trace_hardirqs_on_caller+0xe0/0x1b0
[  522.734790]  i915_pci_probe+0x29/0x90 [i915]
[  522.734801]  pci_device_probe+0xa1/0x130
[  522.734813]  driver_probe_device+0x306/0x480
[  522.734824]  __driver_attach+0xdb/0x100
[  522.734830]  ? driver_probe_device+0x480/0x480
[  522.734836]  ? driver_probe_device+0x480/0x480
[  522.734844]  bus_for_each_dev+0x74/0xc0
[  522.734855]  bus_add_driver+0x15f/0x250
[  522.734863]  ? 0xffffffffa0793000
[  522.734870]  driver_register+0x56/0xe0
[  522.734877]  ? 0xffffffffa0793000
[  522.734883]  do_one_initcall+0x58/0x370
[  522.734893]  ? do_init_module+0x1d/0x1ea
[  522.734900]  ? rcu_read_lock_sched_held+0x6f/0x80
[  522.734906]  ? kmem_cache_alloc_trace+0x282/0x2e0
[  522.734918]  do_init_module+0x56/0x1ea
[  522.734927]  load_module+0x2435/0x2b20
[  522.734965]  ? __se_sys_finit_module+0xd3/0xf0
[  522.734972]  __se_sys_finit_module+0xd3/0xf0
[  522.734995]  do_syscall_64+0x55/0x190
[  522.735003]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[  522.735009] RIP: 0033:0x7f43f675d839
[  522.735014] Code: 00 f3 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 1f f6 2c 00 f7 d8 64 89 01 48
[  522.735260] RSP: 002b:00007ffe69384238 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[  522.735269] RAX: ffffffffffffffda RBX: 000056100e387090 RCX: 00007f43f675d839
[  522.735273] RDX: 0000000000000000 RSI: 000056100e37bff0 RDI: 0000000000000003
[  522.735278] RBP: 000056100e37bff0 R08: 0000000000000000 R09: 0000000000000000
[  522.735282] R10: 0000000000000003 R11: 0000000000000246 R12: 0000000000000000
[  522.735286] R13: 000056100e37c890 R14: 0000000000000020 R15: 0000000000000027
[  522.735309] irq event stamp: 1389594
[  522.735316] hardirqs last  enabled at (1389593): [<ffffffff810f896c>] console_unlock+0x3fc/0x600
[  522.735323] hardirqs last disabled at (1389594): [<ffffffff81a0111c>] error_entry+0x7c/0x100
[  522.735329] softirqs last  enabled at (1389356): [<ffffffff81c0034f>] __do_softirq+0x34f/0x505
[  522.735336] softirqs last disabled at (1389335): [<ffffffff8108c7b9>] irq_exit+0xa9/0xc0
[  522.735432] WARNING: CPU: 1 PID: 3856 at drivers/gpu/drm/i915/intel_pm.c:7350 intel_cleanup_gt_powersave+0x5f/0x70 [i915]

Testcase: igt/drv_module_reload/basic-reload-inject
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712105454.16091-1-chris@chris-wilson.co.uk

drm/i915/tv: fix strncpy truncation warning

Change it to use strlcpy instead

Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712074103.21571-1-chris@chris-wilson.co.uk
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Merge tag 'gvt-next-2018-07-11' of https://github.com/intel/gvt-linux into drm-intel-next-queued

gvt-next-2018-07-11

- vGPU huge page support (Changbin)
- BXT display irq warning fix (Colin)
- Handle GVT dependency well (Henry)

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180711023353.GU1267@zhen-hp.sh.intel.com

drm/i915/execlists: Switch to rb_root_cached

The kernel recently gained an augmented rbtree with the purpose of
cacheing the leftmost element of the rbtree, a frequent optimisation to
avoid calls to rb_first() which is also employed by the
execlists->queue. Switch from our open-coded cache to the library.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180629075348.27358-9-chris@chris-wilson.co.uk

drm/i915/selftests: Add a safety net to live_workarounds

Since live_workarounds poke around the w/a registers and checks to see
if they survive across a reset, we are prone to fouling the machine and
leaving it in a non-recoverable state. Wrap the probe inside a timeout
to abort the test if the reset fails.

v2: Include GEM_TRACE on declaring wedged.
v3: Add a few includes to make the header look standalone.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107188
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180711122952.18448-1-chris@chris-wilson.co.uk

drm/i915: Introduce i915_address_space.mutex

Add a mutex into struct i915_address_space to be used while operating on
the vma and their lists for a particular vm. As this may be called from
the shrinker, we taint the mutex with fs_reclaim so that from the start
lockdep warns us if we are caught holding the mutex across an
allocation. (With such small steps we will eventually rid ourselves of
struct_mutex recursion!)

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180711073608.20286-2-chris@chris-wilson.co.uk

drm/i915: use the ICL stolen memory

Now that our stolen memory is already reserved by the x86 subsystem
(since commit "x86/gpu: reserve ICL's graphics stolen memory"), make
use of it.

Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: x86@kernel.org
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180504203252.28048-2-paulo.r.zanoni@intel.com

x86/gpu: reserve ICL's graphics stolen memory

ICL changes the registers and addresses to 64 bits.

I also briefly looked at implementing an u64 version of the PCI config
read functions, but I concluded this wouldn't be trivial, so it's not
worth doing it for a single user that can't have any racing problems
while reading the register in two separate operations.

v2:
 - Scrub the development (non-public) changelog (Joonas).
 - Remove the i915.ko bits so this can be easily backported in order
   to properly avoid stolen memory even on machines without i915.ko
   (Joonas).
 - CC stable for the reasons above.

Issue: VIZ-9250
CC: stable@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: x86@kernel.org
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Fixes: 412310019a20 ("drm/i915/icl: Add initial Icelake definitions.")
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180504203252.28048-1-paulo.r.zanoni@intel.com

drm/i915: Unwind HW init after GVT setup failure

Following intel_gvt_init() failure, we missed unwinding our setup
leaving pointers dangling past the module unload. For our example, the
pm_qos:

[  441.057615] top: 000000006b3baf1c, n: 0000000054d8ef33, p: 0000000097cdf1a2
               prev: 0000000054d8ef33, n: 0000000097cdf1a2, p: 000000006b3baf1c
               next: 0000000097cdf1a2, n: 000000006de8fc8b, p: 0000000081087253
[  441.057627] WARNING: CPU: 4 PID: 9277 at lib/plist.c:42 plist_check_prev_next+0x2d/0x40
[  441.057628] Modules linked in: i915(+) vgem snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic x86_pkg_temp_thermal intel_powerclamp coretemp crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec snd_hwdep snd_hda_core e1000e snd_pcm mei_me mei prime_numbers [last unloaded: i915]
[  441.057652] CPU: 4 PID: 9277 Comm: drv_selftest Tainted: G     U            4.18.0-rc4-CI-CI_DRM_4464+ #1
[  441.057653] Hardware name: System manufacturer System Product Name/Z170 PRO GAMING, BIOS 3402 04/26/2017
[  441.057656] RIP: 0010:plist_check_prev_next+0x2d/0x40
[  441.057657] Code: 08 48 39 f0 74 2b 49 89 f0 48 8b 4f 08 50 ff 32 52 48 89 fe 41 ff 70 08 48 8b 17 48 c7 c7 d8 ae 14 82 4d 8b 08 e8 63 0e 76 ff <0f> 0b 48 83 c4 20 c3 48 39 10 75 d0 f3 c3 0f 1f 44 00 00 41 54 55
[  441.057717] RSP: 0018:ffffc900003a3a68 EFLAGS: 00010082
[  441.057720] RAX: 0000000000000000 RBX: ffff8802193978c0 RCX: 0000000000000002
[  441.057721] RDX: 0000000080000002 RSI: ffffffff820c65a4 RDI: 00000000ffffffff
[  441.057722] RBP: ffff8802193978c0 R08: 0000000000000000 R09: 0000000000000001
[  441.057724] R10: ffffc900003a3a70 R11: 0000000000000000 R12: ffffffff82243de0
[  441.057725] R13: ffffffff82243de0 R14: ffff88021a6c78c0 R15: 0000000077359400
[  441.057726] FS:  00007fc23a4a9980(0000) GS:ffff880236d00000(0000) knlGS:0000000000000000
[  441.057728] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  441.057729] CR2: 0000563e4503d038 CR3: 0000000138f86005 CR4: 00000000003606e0
[  441.057730] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  441.057731] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  441.057732] Call Trace:
[  441.057736]  plist_check_list+0x2e/0x40
[  441.057738]  plist_add+0x23/0x130
[  441.057743]  pm_qos_update_target+0x1bd/0x2f0
[  441.057771]  i915_driver_load+0xec4/0x1060 [i915]
[  441.057775]  ? trace_hardirqs_on_caller+0xe0/0x1b0
[  441.057800]  i915_pci_probe+0x29/0x90 [i915]
[  441.057804]  pci_device_probe+0xa1/0x130
[  441.057807]  driver_probe_device+0x306/0x480
[  441.057810]  __driver_attach+0xdb/0x100
[  441.057812]  ? driver_probe_device+0x480/0x480
[  441.057813]  ? driver_probe_device+0x480/0x480
[  441.057816]  bus_for_each_dev+0x74/0xc0
[  441.057819]  bus_add_driver+0x15f/0x250
[  441.057821]  ? 0xffffffffa0696000
[  441.057823]  driver_register+0x56/0xe0
[  441.057825]  ? 0xffffffffa0696000
[  441.057827]  do_one_initcall+0x58/0x370
[  441.057830]  ? do_init_module+0x1d/0x1ea
[  441.057832]  ? rcu_read_lock_sched_held+0x6f/0x80
[  441.057834]  ? kmem_cache_alloc_trace+0x282/0x2e0
[  441.057838]  do_init_module+0x56/0x1ea
[  441.057841]  load_module+0x2435/0x2b20
[  441.057852]  ? __se_sys_finit_module+0xd3/0xf0
[  441.057854]  __se_sys_finit_module+0xd3/0xf0
[  441.057861]  do_syscall_64+0x55/0x190
[  441.057863]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[  441.057865] RIP: 0033:0x7fc239d75839
[  441.057866] Code: 00 f3 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 1f f6 2c 00 f7 d8 64 89 01 48
[  441.057927] RSP: 002b:00007fffb7825d38 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[  441.057930] RAX: ffffffffffffffda RBX: 0000563e45035dd0 RCX: 00007fc239d75839
[  441.057931] RDX: 0000000000000000 RSI: 0000563e4502f8a0 RDI: 0000000000000004
[  441.057932] RBP: 0000563e4502f8a0 R08: 0000000000000004 R09: 0000000000000000
[  441.057933] R10: 00007fffb7825ea0 R11: 0000000000000246 R12: 0000000000000000
[  441.057934] R13: 0000563e4502f690 R14: 0000000000000000 R15: 000000000000003f
[  441.057940] irq event stamp: 231338
[  441.057943] hardirqs last  enabled at (231337): [<ffffffff8193e3fc>] _raw_spin_unlock_irqrestore+0x4c/0x60
[  441.057944] hardirqs last disabled at (231338): [<ffffffff8193e26d>] _raw_spin_lock_irqsave+0xd/0x50
[  441.057947] softirqs last  enabled at (231024): [<ffffffff81c0034f>] __do_softirq+0x34f/0x505
[  441.057949] softirqs last disabled at (231005): [<ffffffff8108c7b9>] irq_exit+0xa9/0xc0
[  441.057951] WARNING: CPU: 4 PID: 9277 at lib/plist.c:42 plist_check_prev_next+0x2d/0x40

v2: Add a load failure point to intel_gvt_init() so that we always
exercise this path in future.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107129
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710143821.1889-1-chris@chris-wilson.co.uk

drm/i915: Cleanup modesetting on load-error path

After handling a critical failure initialising GEM we need to unwind the
modesetting setup.

Testcase: igt/drv_module_reload/basic-reload-inject
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710094421.16223-2-chris@chris-wilson.co.uk
Reviewed-by: Matthew Auld <matthew.auld@intel.com>

drm/i915: Flush the residual parking on emergency shutdown

On unwinding following a critical failure inside GEM init, we also need
to be sure to flush the workers before unloading the module.

Testcase: igt/drv_module_reload/basic-reload-inject
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710094421.16223-1-chris@chris-wilson.co.uk

drm/i915: Tidy i915_gem_suspend()

In the next patch, we will make a fairly minor change to flush
outstanding resets before suspend. In order to keep churn to a minimum
in that functional patch, we fix up the comments and coding style now.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709130208.11730-7-chris@chris-wilson.co.uk

drm/i915: Only reset hangcheck at the start of an activity cycle

Across a reset, the seqno (and thus hangcheck) should restart and the
hangcheck naturally progress, for when it does not, we want to declare an
emergency. Currently, we only detect if reset and reinit fails, but we
do not detect if the call to reinit succeeds but the HW is fried - as we
are resetting hangcheck on initialisation the engine. Remove that and
rely on the natural progress to reset the hangcheck timer.

References: e21b141376f9 ("drm/i915: Mark the hangcheck as idle when unparking the engines")
References: 1fd00c0faeec ("drm/i915: Declare the driver wedged if hangcheck makes no progress")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709130208.11730-2-chris@chris-wilson.co.uk

drm/i915/selftests: Filter out both physical address swizzles

In our swizzling selftests, we cannot predict the physical address of
the target page (at least not simply!) and so skip bit17 swizzles.
However, there are two bit17 swizzle modes and we only skipped one, with
the second being observed on the lab gdg causing the test to fail,
as soon as we hit a page with bit17 set in its address.

Testcase: igt/drv_selftest/live_objects #gdg
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709194915.5789-1-chris@chris-wilson.co.uk

drm/i915/selftests: Constrain mock_gtt tests to fit within RAM

Be pessimistic and presume that we actually allocate every page we
exercise via the mock_gtt (e.g. for gvt). In which case we have to keep
our working set under the available physical memory to prevent oom.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710080424.7821-1-chris@chris-wilson.co.uk

drm/i915: Remove function details from device error messages

Error messages are intended to be addressed to the user; be clear,
succinct, instructive and unambiguous. Adding the function name to
that message does not add any information the user requires and in
the process makes the message less clear.

E.g.

[  245.539711] i915 0000:00:02.0: [drm:i915_gem_init [i915]] Failed to initialize GPU, declaring it wedged!

becomes

[  245.539711] i915 0000:00:02.0: Failed to initialize GPU, declaring it wedged!

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709134858.12446-1-chris@chris-wilson.co.uk

drm/i915/gvt: declare gvt as i915's soft dependency

This helps initramfs builder and other tools to know the full dependencies
of i915 and have gvt module loaded with i915.

v2: add condition and change to pre-dependency (Chris)
v3: move declaration to gvt.c. (Chris)
v4: remove xengt (Zhenyu)

Signed-off-by: Hang Yuan <hang.yuan@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915: Update DRIVER_DATE to 20180709

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

drm/i915/selftests: Prevent background reaping of active objects

igt_mmap_offset_exhaustion() wants to test what happens when the mmap
space is filled with zombie objects, objects discarded by userspace but
still active on the GPU. As they are only protected by the active
reference, we have to be certain that active reference is kept while we
peek into our dangling pointer. That active reference should not be
freed until we retire, but we do that retirement from a background
thread. This leaves us with a subtle timing problem, exacerbated and
highlighted by KASAN:

<3>[  132.380399] BUG: KASAN: use-after-free in drm_gem_create_mmap_offset+0x8c/0xd0
<3>[  132.380430] Read of size 8 at addr ffff8801e13245f8 by task drv_selftest/5822

<4>[  132.380470] CPU: 0 PID: 5822 Comm: drv_selftest Tainted: G     U            4.18.0-rc3-g7ae7763aa2be-kasan_48+ #1
<4>[  132.380473] Hardware name: Dell Inc. XPS 8300  /0Y2MRG, BIOS A06 10/17/2011
<4>[  132.380475] Call Trace:
<4>[  132.380481]  dump_stack+0x7c/0xbb
<4>[  132.380487]  print_address_description+0x65/0x270
<4>[  132.380493]  kasan_report+0x25b/0x380
<4>[  132.380497]  ? drm_gem_create_mmap_offset+0x8c/0xd0
<4>[  132.380503]  drm_gem_create_mmap_offset+0x8c/0xd0
<4>[  132.380584]  i915_gem_object_create_mmap_offset+0x6d/0x100 [i915]
<4>[  132.380650]  igt_mmap_offset_exhaustion+0x462/0x940 [i915]
<4>[  132.380714]  ? i915_gem_close_object+0x740/0x740 [i915]
<4>[  132.380784]  ? igt_gem_huge+0x269/0x3d0 [i915]
<4>[  132.380865]  __i915_subtests+0x5a/0x160 [i915]
<4>[  132.380936]  __run_selftests+0x1a2/0x2f0 [i915]
<4>[  132.381008]  i915_live_selftests+0x4e/0x80 [i915]
<4>[  132.381071]  i915_pci_probe+0xd8/0x1b0 [i915]
<4>[  132.381077]  pci_device_probe+0x1c5/0x3a0
<4>[  132.381087]  driver_probe_device+0x6b6/0xcb0
<4>[  132.381094]  __driver_attach+0x22d/0x2c0
<4>[  132.381100]  ? driver_probe_device+0xcb0/0xcb0
<4>[  132.381103]  bus_for_each_dev+0x113/0x1a0
<4>[  132.381108]  ? check_flags.part.24+0x450/0x450
<4>[  132.381112]  ? subsys_dev_iter_exit+0x10/0x10
<4>[  132.381123]  bus_add_driver+0x38b/0x6e0
<4>[  132.381131]  driver_register+0x189/0x400
<4>[  132.381136]  ? 0xffffffffc12d8000
<4>[  132.381140]  do_one_initcall+0xa0/0x4c0
<4>[  132.381145]  ? initcall_blacklisted+0x180/0x180
<4>[  132.381152]  ? do_init_module+0x4a/0x54c
<4>[  132.381156]  ? rcu_lockdep_current_cpu_online+0xdc/0x130
<4>[  132.381161]  ? kasan_unpoison_shadow+0x30/0x40
<4>[  132.381169]  do_init_module+0x1b5/0x54c
<4>[  132.381177]  load_module+0x619e/0x9b70
<4>[  132.381202]  ? module_frob_arch_sections+0x20/0x20
<4>[  132.381211]  ? vfs_read+0x257/0x2f0
<4>[  132.381214]  ? vfs_read+0x257/0x2f0
<4>[  132.381221]  ? kernel_read+0x8b/0x130
<4>[  132.381231]  ? copy_strings_kernel+0x120/0x120
<4>[  132.381244]  ? __se_sys_finit_module+0x17c/0x1a0
<4>[  132.381248]  __se_sys_finit_module+0x17c/0x1a0
<4>[  132.381252]  ? __ia32_sys_init_module+0xa0/0xa0
<4>[  132.381261]  ? __se_sys_newstat+0x77/0xd0
<4>[  132.381265]  ? cp_new_stat+0x590/0x590
<4>[  132.381269]  ? kmem_cache_free+0x2f0/0x340
<4>[  132.381285]  do_syscall_64+0x97/0x400
<4>[  132.381292]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
<4>[  132.381295] RIP: 0033:0x7eff4af46839
<4>[  132.381297] Code: 00 f3 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 1f f6 2c 00 f7 d8 64 89 01 48
<4>[  132.381426] RSP: 002b:00007ffcd84f4cf8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
<4>[  132.381432] RAX: ffffffffffffffda RBX: 000055dfdeb429a0 RCX: 00007eff4af46839
<4>[  132.381435] RDX: 0000000000000000 RSI: 000055dfdeb43670 RDI: 0000000000000004
<4>[  132.381437] RBP: 000055dfdeb43670 R08: 0000000000000004 R09: 0000000000000000
<4>[  132.381440] R10: 00007ffcd84f4e60 R11: 0000000000000246 R12: 0000000000000000
<4>[  132.381442] R13: 000055dfdeb3bec0 R14: 0000000000000000 R15: 000000000000003b

<3>[  132.381466] Allocated by task 5822:
<4>[  132.381485]  kmem_cache_alloc+0xdf/0x2e0
<4>[  132.381546]  i915_gem_object_create_internal+0x24/0x1e0 [i915]
<4>[  132.381609]  igt_mmap_offset_exhaustion+0x257/0x940 [i915]
<4>[  132.381677]  __i915_subtests+0x5a/0x160 [i915]
<4>[  132.381742]  __run_selftests+0x1a2/0x2f0 [i915]
<4>[  132.381806]  i915_live_selftests+0x4e/0x80 [i915]
<4>[  132.381865]  i915_pci_probe+0xd8/0x1b0 [i915]
<4>[  132.381868]  pci_device_probe+0x1c5/0x3a0
<4>[  132.381871]  driver_probe_device+0x6b6/0xcb0
<4>[  132.381874]  __driver_attach+0x22d/0x2c0
<4>[  132.381877]  bus_for_each_dev+0x113/0x1a0
<4>[  132.381880]  bus_add_driver+0x38b/0x6e0
<4>[  132.381884]  driver_register+0x189/0x400
<4>[  132.381886]  do_one_initcall+0xa0/0x4c0
<4>[  132.381889]  do_init_module+0x1b5/0x54c
<4>[  132.381892]  load_module+0x619e/0x9b70
<4>[  132.381895]  __se_sys_finit_module+0x17c/0x1a0
<4>[  132.381898]  do_syscall_64+0x97/0x400
<4>[  132.381901]  entry_SYSCALL_64_after_hwframe+0x49/0xbe

<3>[  132.381914] Freed by task 150:
<4>[  132.381931]  kmem_cache_free+0xb7/0x340
<4>[  132.381995]  __i915_gem_free_objects+0x875/0xf50 [i915]
<4>[  132.382054]  __i915_gem_free_work+0x69/0xb0 [i915]
<4>[  132.382058]  process_one_work+0x78b/0x1740
<4>[  132.382061]  worker_thread+0x82/0xb80
<4>[  132.382064]  kthread+0x30c/0x3d0
<4>[  132.382067]  ret_from_fork+0x3a/0x50

<3>[  132.382081] The buggy address belongs to the object at ffff8801e1324500
                   which belongs to the cache drm_i915_gem_object of size 1168
<3>[  132.382133] The buggy address is located 248 bytes inside of
                   1168-byte region [ffff8801e1324500, ffff8801e1324990)
<3>[  132.382179] The buggy address belongs to the page:
<0>[  132.382202] page:ffffea000784c800 count:1 mapcount:0 mapping:ffff8801dedf6500 index:0xffff8801e1323ec0 compound_mapcount: 0
<0>[  132.382251] flags: 0x8000000000008100(slab|head)
<1>[  132.382274] raw: 8000000000008100 ffff8801d6317440 ffff8801d6317440 ffff8801dedf6500
<1>[  132.382307] raw: ffff8801e1323ec0 0000000000140013 00000001ffffffff 0000000000000000
<1>[  132.382339] page dumped because: kasan: bad access detected

<3>[  132.382373] Memory state around the buggy address:
<3>[  132.382395]  ffff8801e1324480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
<3>[  132.382426]  ffff8801e1324500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
<3>[  132.382457] >ffff8801e1324580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
<3>[  132.382488]                                                                 ^
<3>[  132.382517]  ffff8801e1324600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
<3>[  132.382548]  ffff8801e1324680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb

This patch tricks the system into running without the background retire
thread, until after we finish the test. The only reaping should then be
performed by the mmap offset routine to reclaim the space as required.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709130208.11730-1-chris@chris-wilson.co.uk

drm/i915/selftests: Replace wait-on-timeout with explicit timeout

In igt_flush_test() we install a background timer in order to ensure
that the wait completes within a certain time. We can now tell the wait
that it has to complete within a timeout, and so no longer need the
background timer.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709122044.7028-3-chris@chris-wilson.co.uk

drm/i915: Provide a timeout to i915_gem_wait_for_idle() on setup

With a broken GPU we expect it to fail during the initial
GPU setup where do a couple of context switches to record the defaults.
This is a task that takes a few milliseconds even on the slowest of
devices, but we may have to wait 60s for hangcheck to give in and
declare the machine inoperable. In this a case where any gpu hang is
unacceptable, both from a timeliness and practical standpoint.

We can therefore set a timeout on our wait-for-idle that is shorter than
the hangcheck (which may be up to 60s for a declaring a wedged driver)
and so detect the broken GPU much more quickly during driver load (and
so prevent stalling userspace for ages).

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709122044.7028-2-chris@chris-wilson.co.uk

drm/i915: Provide a timeout to i915_gem_wait_for_idle()

Usually we have no idea about the upper bound we need to wait to catch
up with userspace when idling the device, but in a few situations we
know the system was idle beforehand and can provide a short timeout in
order to very quickly catch a failure, long before hangcheck kicks in.

In the following patches, we will use the timeout to curtain two overly
long waits, where we know we can expect the GPU to complete within a
reasonable time or declare it broken.

In particular, with a broken GPU we expect it to fail during the initial
GPU setup where do a couple of context switches to record the defaults.
This is a task that takes a few milliseconds even on the slowest of
devices, but we may have to wait 60s for hangcheck to give in and
declare the machine inoperable. In this a case where any gpu hang is
unacceptable, both from a timeliness and practical standpoint.

The other improvement is that in selftests, we do not need to arm an
independent timer to inject a wedge, as we can just limit the timeout on
the wait directly.

v2: Include the timeout parameter in the trace.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709122044.7028-1-chris@chris-wilson.co.uk

drm/i915/selftests: Magic numbers for old Y-tiling

i915g has a slightly different tiling layout, and so requires a
different reference swizzle pattern.

Testcase: igt/drv_selftests/live_objects #gdg
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180707100405.817-1-chris@chris-wilson.co.uk

drm/i915/gvt: Handle EDP_PSR_IMR and EDP_PSR_IIR for BXT.

BXT supports EDP. However since GVT-g only simulate DP monitor
to guest and handles EDP_PSR_IMR and EDP_PSR_IIR as default MMIO
r/w. If guest r/w these IMR/IIR, GVT-g won't simulate the real
HW behavior and below warning is printed:
--------
Interrupt register 0x64838 is not zero: 0xffffffff
WARNING: CPU: 1 PID: 1 at drivers/gpu/drm/i915/i915_irq.c:161
gen3_assert_iir_is_zero+0x34/0xa0

Call Trace:
gen8_de_irq_postinstall+0xad/0x330
gen8_irq_postinstall+0x23/0x80
drm_irq_install+0xb5/0x130
i915_driver_load+0xafd/0xf70
--------
Since GVT-g won't simulate EDP to guest, always set EDP_PSR_IMR
and EDP_PSR_IIR IMR/IIR to 0.

Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915: Enable platform support for vGPU huge gtt pages

Now GVTg supports shadowing both 2M/64K huge gtt pages. So let's turn on
the cap info bit VGT_CAPS_HUGE_GTT.

v2: Split changes in i915 side into a separated patch.

Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Fix error handling in ppgtt_populate_spt_by_guest_entry

Don't forget to free allocated spt if shadowing failed.

Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Handle special sequence on PDE IPS bit

If the guest update the 64K gtt entry before changing IPS bit of PDE, we
need to re-shadow the whole page table. Because we have ignored all
updates to unused entries.

Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Add 2M huge gtt support

This add 2M huge gtt support for GVTg. Unlike 64K gtt entry, we can
shadow 2M guest entry with real huge gtt. But before that, we have to
check memory physical continuous, alignment and if it is supported on
the host. We can get all supported page sizes from
intel_device_info.page_sizes.

Finally we must split the 2M page into smaller pages if we cannot
satisfy guest Huge Page.

Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/kvmgt: Support setting dma map for huge pages

To support huge gtt, we need to support huge pages in kvmgt first.
This patch adds a 'size' param to the intel_gvt_mpt::dma_map_guest_page
API and implements it in kvmgt.

v2: rebase.

Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Add 64K huge gtt support

Finally, this add the first huge gtt support for GVTg - 64K pages. Since
64K page and 4K page cannot be mixed on the same page table, so we always
split a 64K entry into small 4K page. And when unshadow guest 64K entry,
we need ensure all the shadowed entries in shadow page table also get
cleared.

For page table which has 64K gtt entry, only PTE#0, PTE#16, PTE#32, ...
PTE#496 are used. Unused PTEs update should be ignored.

Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Make PTE iterator 64K entry aware

64K PTE is special, only PTE#0, PTE#16, PTE#32, ... PTE#496 are used in
the page table.

Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Split ppgtt_alloc_spt into two parts

We need a interface to allocate a pure shadow page which doesn't have
a guest page associated with. Such shadow page is used to shadow 2M
huge gtt entry.

Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Add GTT clear_pse operation

Add clear_pse operation in case we need to split huge gtt into small pages.

v2: correct description.

Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Add software PTE flag to mark special 64K splited entry

This add a software PTE flag on the Ignored bit of PTE. It will be used
to identify splited 64K shadow entries.

v2: fix mask definition.

Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Detect 64K gtt entry by IPS bit of PDE

This change help us detect the real entry type per PSE and IPS setting.
For 64K entry, we also need to check reg GEN8_GAMW_ECO_DEV_RW_IA.

v2: Extend IPS mmio control to Gen10. (Matthew Auld)

Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Handle MMIO GEN8_GAMW_ECO_DEV_RW_IA for 64K GTT

The register RENDER_HWS_PGA_GEN7 is renamed to GEN8_GAMW_ECO_DEV_RW_IA
from GEN8 which can control IPS enabling.

v3: MMIO control for IPS is not removed from gen9 but gen10 (Matthew Auld)
v2: IPS of all engines must be enabled together for gen9.

Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Add PTE IPS bit operations

Add three IPS operation functions to test/set/clear IPS in PDE.

Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915/gvt: Add new 64K entry type

Add a new entry type GTT_TYPE_PPGTT_PTE_64K_ENTRY. 64K entry is very
different from 2M/1G entry. 64K entry is controlled by IPS bit in upper
PDE. To leverage the current logic, I take IPS bit as 'PSE' for PTE
level. Which means, 64K entries can also processed by get_pse_type().

v2: Make it bisectable.

Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

drm/i915: Replace nested subclassing with explicit subclasses

In the next patch, we will want a third distinct class of timeline that
may overlap with the current pair of client and engine timeline classes.
Rather than use the ad hoc markup of SINGLE_DEPTH_NESTING, initialise
the different timeline classes with an explicit subclass.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706210710.16251-1-chris@chris-wilson.co.uk

drm/i915/selftests: Avoid warning if runtime pm is disabled

Inside the mock GEM device, we try to grab the runtime pm for the fake
device to prevent it from ever suspending. However, if CONFIG_PM is not
set, trying to obtain the wakref returns an error which we WARN about.
Suppress the expected warning.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706205947.11209-1-chris@chris-wilson.co.uk

drm/i915/selftests: Provide full mb() around clflush

clflush is an unserialised instruction and the IA manual strongly advises
you to serialise it with a mb. To be cautious, apply one before and one
after, so that it is serialised with both writes and reads without
worrying too much about the required direction.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706174926.4712-1-chris@chris-wilson.co.uk

drm/i915: Track the last-active inside the i915_vma

Using a VMA on more than one timeline concurrently is the exception
rather than the rule (using it concurrently on multiple engines). As we
expect to only use one active tracker, store the most recently used
tracker inside the i915_vma itself and only fallback to the rbtree if
we need a second or more concurrent active trackers.

v2: Comments on how we overwrite any existing last_active cache.
v3: __list_del_entry() before list_replace_init() is confusing and, much
more important, entirely redundant.
v4: Note that both last_active and the rbtree may be simultaneously
tracking this timeline, albeit with different requests, and so the vma
may be retired twice for the same timeline.
v5: No, that list_del is required!

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706123157.9645-1-chris@chris-wilson.co.uk

drm/i915: Track vma activity per fence.context, not per engine

In the next patch, we will want to be able to use more flexible request
timelines that can hop between engines. From the vma pov, we can then
not rely on the binding of this request to an engine and so can not
ensure that different requests are ordered through a per-engine
timeline, and so we must track activity of all timelines. (We track
activity on the vma itself to prevent unbinding from HW before the HW
has finished accessing it.)

v2: Switch to a rbtree for 32b safety (since using u64 as a radixtree
index is fraught with aliasing of unsigned longs).
v3: s/lookup_active/active_instance/ because we can never agree on names

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706103947.15919-5-chris@chris-wilson.co.uk

drm/i915: Move i915_vma_move_to_active() to i915_vma.c

i915_vma_move_to_active() has grown beyond its execbuf origins, and
should take its rightful place in i915_vma.c as a method for i915_vma!

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706103947.15919-4-chris@chris-wilson.co.uk

drm/i915: Start returning an error from i915_vma_move_to_active()

Handling such a late error in request construction is tricky, but to
accommodate future patches which may allocate here, we potentially could
err. To handle the error after already adjusting global state to track
the new request, we must finish and submit the request. But we don't
want to use the request as not everything is being tracked by it, so we
opt to cancel the commands inside the request.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706103947.15919-3-chris@chris-wilson.co.uk

drm/i915: Export i915_request_skip()

In the next patch, we will want to start skipping requests on failing to
complete their payloads. So export the utility function current used to
make requests inoperable following a failed gpu reset.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706103947.15919-2-chris@chris-wilson.co.uk

drm/i915: Refactor export_fence() after i915_vma_move_to_active()

Currently all callers are responsible for adding the vma to the active
timeline and then exporting its fence. Combine the two operations into
i915_vma_move_to_active() to move all the extra handling from the
callers to the single site.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706103947.15919-1-chris@chris-wilson.co.uk

drm/i915/selftests: Fixup missing MI_MEM_VIRTUAL for live_hangcheck

We always want to use a virtual address (i.e. use the GTT) for
MI_STORE_DWORD_IMM, but forgot the ever so important flag in
live_hangcheck for gen3.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706142323.25699-2-chris@chris-wilson.co.uk

drm/i915/selftests: Replace magic 1<<22 with MI_USE_GGTT/MI_MEM_VIRTUAL

Replace the magic bit with the proper symbolic name for instructing
MI_STORE_DWORD_IMM to use a virtual address (on gen3) or the global GTT
address (still virtual!) on gen4+.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706142323.25699-1-chris@chris-wilson.co.uk
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

drm/i915/selftests: Limit live_gtt allocation test to fit within RAM

Limit the GTT size we try and allocate to ensure that it fits within RAM
and does not trigger the oomkiller indiscriminately.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706125338.24432-1-chris@chris-wilson.co.uk

drm/i915/gtt: Control cache domain of dma_map_page() directly

We already maually control the CPU cache for our page table directories,
so we can tell the dma mapper to skip doing it as well.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706122611.4142-2-chris@chris-wilson.co.uk

drm/i915/gtt: Suppress warnings for dma_map_page

As we propagate back the error to the caller for them to handle, we do
not need the lowest level spitting out a redundant warning upon an
allocation failure inside dma_map_page().

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706122611.4142-1-chris@chris-wilson.co.uk

drm/i915: Flush the WCB following a WC write

If we have just completed a WC write, we must ensure that the WCB (Write
Combining Buffer) is flushed out to main memory before we can expect to
see the results. This is especially important when mixing WC with GTT as
the physical paths are different and cachelines are not naturally flushed.

Testcase: igt/drv_selftests/live_coherency #gdg
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706115402.18547-1-chris@chris-wilson.co.uk

drm/i915/selftests: Skip live_execlists if the GPU is terminally wedged

If the GPU is irrecoverably wedged, we can not execute any requests
making testing execlists (request execution) pointless. Skip!

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706114510.18467-1-chris@chris-wilson.co.uk

drm/i915/selftests: Skip live context execution test without logical contexts

If the HW (or driver) doesn't support logical contexts, don't pretend we
gain anything from trying to execute GPU commands with them. At best it
reports -ENODEV, which is an unhelpful failure that we should just skip.

v2: Be more specific and check the driver/engine caps for logical (HW)
context support.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706101923.28548-1-chris@chris-wilson.co.uk

drm/i915: Record logical context support in driver caps

Avoid looking at the magical engines[RCS] to decide if the HW and driver
supports logical contexts, and instead record that knowledge during
initialisation.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706101442.21279-1-chris@chris-wilson.co.uk

drm/i915/ddi: Simplify get_encoder_power_domains()

We can simplify the encoder's get_power_domains() hook by calling it
only if the encoder is active. That way the hook can return its power
domains unconditionally without checking the active state by calling
encoder::get_hw_state(). This get_hw_state() query is in fact
redundant since it's already done by intel_modeset_readout_hw_state()
setting the encoder's crtc or leaving it NULL accordingly. Let's use
this fact to decide if the encoder is active.

While at it clarify the comment in intel_ddi_get_power_domains() about
primary vs. fake MST encoders and make sure we never do an incorrect
encoder->dig_port cast for fake MST encoders.

Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705122654.17072-1-imre.deak@intel.com

drm/i915: Remove support for legacy debugfs crc interface

This interface is deprecated, and has been replaced by the upstream
drm crc interface.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Cc: Petri Latvala <petri.latvala@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628072303.14175-1-maarten.lankhorst@linux.intel.com

drm/i915/selftests: Skip over live context testing when wedged

If the GPU is terminally wedged we cannot submit any requests into a
context, completely unfulfilling our purpose of doing so. As this
expectedly fails, skip over the test.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706065332.15214-9-chris@chris-wilson.co.uk

drm/i915/selftests: Skip huge pages live tests if wedged

We test the GPU handling of huge pages by submitting requests that write
into a huge page, but if the GPU is irrecoverably wedged we cannot
submit any requests. As the test expectedly fails, skip over it.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706065332.15214-8-chris@chris-wilson.co.uk

drm/i915/selftests: Skip live eviction tests when wedged

If the GPU is irrecoverably wedged, we cannot submit any requests and so
cannot make the GTT busy in order to test evicting active objects. As
this expectedly fails, skip over the test.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706065332.15214-7-chris@chris-wilson.co.uk

drm/i915/selftests: Skip workaround tests when wedged

If the GPU is irrecoverably wedged, we cannot submit any request and
therefore cannot query the register state of the context (which is done
using the GPU command stream). So skip over the test as it expectedly
fails.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706065332.15214-6-chris@chris-wilson.co.uk

drm/i915/selftests: Skip all request selftests when wedged

If the GPU is irrecoverably wedge, we cannot submit any request and so
all of the request selftests will expectedly fail. Skip over them.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706065332.15214-5-chris@chris-wilson.co.uk

drm/i915/selftests: Skip making an object busy if the GPU is wedged

If the GPU is wedged, we cannot make the object busy as trying to
submit a request will generate -EIO. Skip to the end of the test.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706065332.15214-4-chris@chris-wilson.co.uk

drm/i915/selftests: Skip using the GPU if wedged

If the GPU is irrecoverably broken, we can not use it to dirty memory
and check for cache coherency with the CPU. All we can do is simply skip
over the GPU subtests and focus on the CPU domains (WC, WB) cache
management.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107127
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706065332.15214-3-chris@chris-wilson.co.uk

drm/i915/selftests: Destroy partial tiling vma after use

As we keep VMA around until the object is destroyed, when testing
partial tiling we instantiate many, many VMA (as the object is huge
allowing for many different partial regions). We test elsewhere our
handling of populating large objects with a full set of VMA and checking
we can retrieve them afterwards, but in this test we incur the cost of
flushing all VMA after every GTT write, dramatically slowing down the
test.

References: https://bugs.freedesktop.org/show_bug.cgi?id=107130
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706065332.15214-2-chris@chris-wilson.co.uk

drm/i915: Squelch very verbose error logging

Having found the error causing the IGT test to fail, downgrade the
verbose logging so that we stop flooding the syslogs as we deliberately
provoke it many thousands of time during selftests.

References: 10195b1e4411 ("drm/i915: Show vma allocator stack when in doubt")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706065332.15214-1-chris@chris-wilson.co.uk

drm/i915/icl: Define AUX lane registers for Port A/B

This patch defines AUX lane registers for PORT_PCS_DW1,
PORT_TX_DW2, PORT_TX_DW4, PORT_TX_DW5 used during
dsi enabling.

v2: Review comments from Jani N:
    - Define _ICL_PORT_PCS_DW1_AUX_A for consistency
    - Three spaces for bitfield definition.

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530798591-2077-8-git-send-email-madhav.chauhan@intel.com

drm/i915/icl: Power down unused DSI lanes

To save power, unused lanes should be powered
down using the bitfield of PORT_CL_DW10.

v2: Review comments from Jani N
    - Put default label next to case 4
    - Include the shifts in the macros

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530798591-2077-7-git-send-email-madhav.chauhan@intel.com

drm/i915/icl: Define PORT_CL_DW_10 register

This register used to power down individual lanes for
DDI/DSI ports. Bitfields to power up/down various
combinations of lanes are also added in this patch.

v2: Review comments from Jani N
    - Use override instead of "override" for bitfields
    - Define mask for override bitfield
    - Define PWR_DOWN_LN* macros shifted in place
v3: Correct PWR_DOWN_LN_MASK value (Jani N)

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530798591-2077-6-git-send-email-madhav.chauhan@intel.com

drm/i915/icl: Enable DSI IO power

This patch configures mode of operation for DSI
and enable DDI IO power by configuring power well.

v2: Use for_each_dsi_port() for power get (Jani N)

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530798591-2077-5-git-send-email-madhav.chauhan@intel.com

drm/i915/icl: Define DSI mode ctl register

This patch defines DSI IO mode control register and it's bits
used while enabling IO power for DSI.

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530798591-2077-4-git-send-email-madhav.chauhan@intel.com

drm/i915/icl: Program DSI Escape clock Divider

Escape Clock is used for LP communication across the DSI
Link. To achieve the constant frequency of the escape clock
from the variable DPLL frequency output, a variable divider(M)
is needed. This patch programs the same.

v2: (Jani N) Don't end line with "(".

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1530798591-2077-3-git-send-email-madhav.chauhan@intel.com

drm/i915/dsi: update some of the platform based checks

Use the more customary order of latest platform first, and don't bother
with an if in the last branch.

Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705132509.12881-3-jani.nikula@intel.com

drm/i915/dsi: use vlv and bxt prefixes for the global DSI functions

Avoid confusion with the functions to be added for the new ICL or gen 11
DSI implementation by renaming the current DSI functions. While at it,
permutate the words in the function names to make them all start with
"vlv_dsi" or "vlv_dsi_pll" etc.

Reduce the platform abstractions in the PLL file while at it, moving the
checks to vlv_dsi.c instead, where we typically already have the
necessary if ladders.

Leave the static functions as-is for now; they could be renamed later if
needed.

No functional changes.

v2: use "gen7" prefix.

v3: use "vlv" and "bxt" prefixes, reduce the abstractions.

References: https://patchwork.freedesktop.org/series/44823/
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705132509.12881-2-jani.nikula@intel.com

drm/i915/dsi: rename the current DSI files based on first platform

Starting from ICL or gen 11 we have a new DSI block which requires
completely different programming from the current implementation. Having
them in the same file would be confusing. Rename the current DSI and DSI
PLL implementation files as vlv_dsi.c and vlv_dsi_pll.c.

No functional changes.

v2: use "gen7" prefix.

v3: use "vlv" prefix.

References: https://patchwork.freedesktop.org/series/44823/
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705132509.12881-1-jani.nikula@intel.com

drm/i915/selftests: Fail hangcheck testing if the GPU is wedged

If the GPU is irrecoverably wedged on startup, it means that it failed
on initialisation and we have already tried to reset it but failed. We
can ignore all further testing, as it is already dead. Failing early,
prevents us from slowly failing in our endeavours later and timing out.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705150214.28316-1-chris@chris-wilson.co.uk

drm/i915/selftests: Detect unknown swizzling correctly

i915_gem_detect_bit_6_swizzle() tries to hide unknown swizzling from
userspace (and ourselves) leaving us with the only clue inside
i915->quirks & QUIRK_PIN_SWIZZLED_PAGES. If we see this bit set, it
means that we really have no clue as to what the swizzle pattern is
being used in any one page and so cannot compute what the reference
value should be in our tiling selftests. We have to skip the test.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107133
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705171523.18462-1-chris@chris-wilson.co.uk

drm/i915: Remove pointless if-else from sdvo code

The return value is a bool so we can just return the result of
the biwise AND. The compiler will take care of the rest.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180621174658.18823-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/selftests: Fixup recursive MI_BB_START for gen3

There's no magic bit0 in MI_BB_START for gen3, it's the same dword length
parameter as elsewhere and needs to be zero.

v2: Same bug in both live_requests and live_hanghcheck.

References: https://bugs.freedesktop.org/show_bug.cgi?id=107132
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705154756.5533-1-chris@chris-wilson.co.uk
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

drm/i915: Mark expected switch fall-throughs

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 141432
Addresses-Coverity-ID: 141433
Addresses-Coverity-ID: 141434
Addresses-Coverity-ID: 141435
Addresses-Coverity-ID: 141436
Addresses-Coverity-ID: 1357360
Addresses-Coverity-ID: 1357403
Addresses-Coverity-ID: 1357433
Addresses-Coverity-ID: 1392622
Addresses-Coverity-ID: 1415273
Addresses-Coverity-ID: 1435752
Addresses-Coverity-ID: 1441500
Addresses-Coverity-ID: 1454596
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628223541.GA17665@embeddedor.com

drm/i915/icl: Define register for DSI PLL

This patch adds the new registers and corresponding bit definitions
which will be used for programming/enable DSI PLL.

v2: Review comments from Jani N
    - Fix spaces while defining ICL_ESC_CLK_DIV_MASK
    - Define shift and mask for bitfields.

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530795727-28644-2-git-send-email-madhav.chauhan@intel.com

drm/i915/selftests: Replace open-coded i915_address_space_init()

Use i915_address_space_init() rather than open-code it inside
mock_ppgtt() as we will forget to keep it in sync.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705065653.20449-3-chris@chris-wilson.co.uk

drm/i915/selftests: Use full release for local ppgtt allocation

We can now use the full release mechanism (i915_ppgtt_put) for our local
ppgtt allocation in igt_ppgtt_alloc.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705065653.20449-2-chris@chris-wilson.co.uk

drm/i915: Remove defunct i915->vm_list

No longer used and can be removed. One less global that currently
demands struct_mutex protection.

References: e9e7dc4144cd ("drm/i915/gtt: Make gen6 page directories evictable")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705065653.20449-1-chris@chris-wilson.co.uk

drm/i915/gtt: Pull global wc page stash under its own locking

Currently, the wc-stash used for providing flushed WC pages ready for
constructing the page directories is assumed to be protected by the
struct_mutex. However, we want to remove this global lock and so must
install a replacement global lock for accessing the global wc-stash (the
per-vm stash continues to be guarded by the vm).

We need to push ahead on this patch due to an oversight in hastily
removing the struct_mutex guard around the igt_ppgtt_alloc selftest. No
matter, it will prove very useful (i.e. will be required) in the near
future.

v2: Restore the onstack stash so that we can drop the vm->mutex in
future across the allocation.
v3: Restore the lost pagevec_init of the onstack allocation, and repaint
function names.
v4: Reorder init so that we don't try and use i915_address_space before
it is ininitialised.

Fixes: 1f6f00238abf ("drm/i915/selftests: Drop struct_mutex around lowlevel pggtt allocation")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180704185518.4193-1-chris@chris-wilson.co.uk

drm/i915: Unmask and enable master error interrupt on gen2/3

For whatever reason we only unmask and enable the master error
interrut on gen4. With the EIR handling fixed let's do that
on gen2/3 as well.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611200258.27121-4-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Fix pre-ILK error interrupt ack

Adjust the EIR clearing to cope with the edge triggered IIR
on i965/g4x. To guarantee an edge in the ISR master error bit
we temporarily mask everything in EMR. As some of the EIR bits
can't even be directly cleared we also borrow a trick from
i915_clear_error_registers() and permanently mask any bit that
remains high. No real thought given to how we might unmask them
again once the cause for the error has been clered. I suppose
on pre-g4x GPU reset will reinitialize EMR from scratch.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611200258.27121-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Fix hotplug irq ack on i965/g4x

Just like with PIPESTAT, the edge triggered IIR on i965/g4x
also causes problems for hotplug interrupts. To make sure
we don't get the IIR port interrupt bit stuck low with the
ISR bit high we must force an edge in ISR. Unfortunately
we can't borrow the PIPESTAT trick and toggle the enable
bits in PORT_HOTPLUG_EN as that act itself generates hotplug
interrupts. Instead we just have to loop until we've cleared
PORT_HOTPLUG_STAT, or we just give up and WARN.

v2: Don't frob with PORT_HOTPLUG_EN

Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614175625.1615-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915/selftests: Drop struct_mutex around lowlevel pggtt allocation

For a ppgtt that we are constructing, there is no struct_mutex
dependence so skip it. In the process, also ping the scheduler
frequently to try and avoid the NMI watchdog.

v2: gen6 requires struct_mutex to clean up (currently)

Suggested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=107094
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180703135331.12265-1-chris@chris-wilson.co.uk

drm/i915/selftests: Release the struct_mutex to free the objects

live_gtt is a very slow test to run, simply because it tries to allocate
and use as much as the 48b address space as possibly can and in the
process will try to own all of the system memory. This leads to resource
exhaustion and CPU starvation; the latter impacts us when the NMI
watchdog declares a task hung due to a mutex contention with ourselves.
This we can prevent by releasing the struct_mutex and forcing our
i915/rcu workers to run, and in particular flushing the freed object
worker that is the cause for concern.

References: https://bugs.freedesktop.org/show_bug.cgi?id=107094
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180703101829.7360-1-chris@chris-wilson.co.uk

drm/i915: Wait for PSR exit before checking for vblank evasion

The PIPEDSL freezes on PSR entry and if PSR hasn't fully exited, then
the pipe_update_start call schedules itself out to check back later.

On ChromeOS-4.4 kernel, which is fairly up-to-date w.r.t drm/i915 but
lags w.r.t core kernel code, hot plugging an external display triggers
tons of "potential atomic update errors" in the dmesg, on *pipe A*. A
closer analysis reveals that we try to read the scanline 3 times and
eventually timeout, b/c PSR hasn't exited fully leading to a PIPEDSL
stuck @ 1599. This issue is not seen on upstream kernels, b/c for *some*
reason we loop inside intel_pipe_update start for ~2+ msec which in this
case is more than enough to exit PSR fully, hence an *unstuck* PIPEDSL
counter, hence no error. On the other hand, the ChromeOS kernel spends
~1.1 msec looping inside intel_pipe_update_start and hence errors out
b/c the source is still in PSR.

Regardless, we should wait for PSR exit (if PSR is disabled, we incur
a ~1-2 usec penalty) before reading the PIPEDSL, b/c if we haven't
fully exited PSR, then checking for vblank evasion isn't actually
applicable.

v4: Comment explaining psr_wait after enabling VBL interrupts (DK)

v5: CAN_PSR() to handle platforms that don't support PSR.

v6: Handle local_irq_disable on early return (Chris)

Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Tarun Vyas <tarun.vyas@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180627200250.1515-2-tarun.vyas@intel.com