soundwire: cadence: Remove wasted space in response_buf

[ Upstream commit 827c32d0df4bbe0d1c47d79f6a5eabfe9ac75216 ]

The response_buf was declared much larger (128 entries) than the number
of responses that could ever be written into it. The Cadence IP is
configurable up to a maximum of 32 entries, and the datasheet says
that RX_FIFO_AVAIL can be 2 larger than this. So allow up to 34
responses.

Also add checking in cdns_read_response() to prevent overflowing
reponse_buf if RX_FIFO_AVAIL contains an unexpectedly large number.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221202161812.4186897-3-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iommu: Attach device group to old domain in error path

[ Upstream commit 2cc73c5712f97de98c38c2fafc1f288354a9f3c3 ]

iommu_attach_group() attaches all devices in a group to domain and then
sets group domain (group->domain). Current code (__iommu_attach_group())
does not handle error path. This creates problem as devices to domain
attachment is in inconsistent state.

Flow:
  - During boot iommu attach devices to default domain
  - Later some device driver (like amd/iommu_v2 or vfio) tries to attach
    device to new domain.
  - In iommu_attach_group() path we detach device from current domain.
    Then it tries to attach devices to new domain.
  - If it fails to attach device to new domain then device to domain link
    is broken.
  - iommu_attach_group() returns error.
  - At this stage iommu_attach_group() caller thinks, attaching device to
    new domain failed and devices are still attached to old domain.
  - But in reality device to old domain link is broken. It will result
    in all sort of failures (like IO page fault) later.

To recover from this situation, we need to attach all devices back to the
old domain. Also log warning if it fails attach device back to old domain.

Suggested-by: Lu Baolu <baolu.lu@linux.intel.com>
Reported-by: Matt Fagnani <matt.fagnani@bell.net>
Signed-off-by: Vasant Hegde <vasant.hegde@amd.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Tested-by: Matt Fagnani <matt.fagnani@bell.net>
Link: https://lore.kernel.org/r/20230215052642.6016-1-vasant.hegde@amd.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216865
Link: https://lore.kernel.org/lkml/15d0f9ff-2a56-b3e9-5b45-e6b23300ae3b@leemhuis.info/
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/cma: Distinguish between sockaddr_in and sockaddr_in6 by size

[ Upstream commit 876e480da2f74715fc70e37723e77ca16a631e35 ]

Clang can do some aggressive inlining, which provides it with greater
visibility into the sizes of various objects that are passed into
helpers. Specifically, compare_netdev_and_ip() can see through the type
given to the "sa" argument, which means it can generate code for "struct
sockaddr_in" that would have been passed to ipv6_addr_cmp() (that expects
to operate on the larger "struct sockaddr_in6"), which would result in a
compile-time buffer overflow condition detected by memcmp(). Logically,
this state isn't reachable due to the sa_family assignment two callers
above and the check in compare_netdev_and_ip(). Instead, provide a
compile-time check on sizes so the size-mismatched code will be elided
when inlining. Avoids the following warning from Clang:

../include/linux/fortify-string.h:652:4: error: call to '__read_overflow' declared with 'error' attribute: detected read beyond size of object (1st parameter)
                        __read_overflow();
                        ^
note: In function 'cma_netevent_callback'
note:   which inlined function 'node_from_ndev_ip'
1 error generated.

When the underlying object size is not known (e.g. with GCC and older
Clang), the result of __builtin_object_size() is SIZE_MAX, which will also
compile away, leaving the code as it was originally.

Link: https://lore.kernel.org/r/20230208232549.never.139-kees@kernel.org
Link: https://github.com/ClangBuiltLinux/linux/issues/1687
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Nathan Chancellor <nathan@kernel.org> # build
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

phy: rockchip-typec: Fix unsigned comparison with less than zero

[ Upstream commit f765c59c5a72546a2d74a92ae5d0eb0329d8e247 ]

The dp and ufp are defined as bool type, the return value type of
function extcon_get_state should be int, so the type of dp and ufp
are modified to int.

./drivers/phy/rockchip/phy-rockchip-typec.c:827:12-14: WARNING: Unsigned expression compared with zero: dp > 0.

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3962
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230213035709.99027-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: pciehp: Add Qualcomm quirk for Command Completed erratum

[ Upstream commit 82b34b0800af8c9fc9988c290cdc813e0ca0df31 ]

The Qualcomm PCI bridge device (Device ID 0x010e) found in chipsets such as
SC8280XP used in Lenovo Thinkpad X13s, does not set the Command Completed
bit unless writes to the Slot Command register change "Control" bits.

This results in timeouts like below during boot and resume from suspend:

  pcieport 0002:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
  ...
  pcieport 0002:00:00.0: pciehp: Timeout on hotplug command 0x13f1 (issued 107724 msec ago)

Add the device to the Command Completed quirk to mark commands "completed"
immediately unless they change the "Control" bits.

Link: https://lore.kernel.org/r/20230213144922.89982-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: Add ACS quirk for Wangxun NICs

[ Upstream commit a2b9b123ccac913e9f9b80337d687a2fe786a634 ]

Wangxun has verified there is no peer-to-peer between functions for the
below selection of SFxxx, RP1000 and RP2000 NICS.  They may be
multi-function devices, but the hardware does not advertise ACS capability.

Add an ACS quirk for these devices so the functions can be in independent
IOMMU groups.

Link: https://lore.kernel.org/r/20230207102419.44326-1-mengyuanlou@net-swift.com
Signed-off-by: Mengyuan Lou <mengyuanlou@net-swift.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: loongson: Add more devices that need MRRS quirk

[ Upstream commit c768f8c5f40fcdc6f058cc2f02592163d6c6716c ]

Loongson-2K SOC and LS7A2000 chipset add new PCI IDs that need MRRS
quirk.  Add them.

Link: https://lore.kernel.org/r/20230211023321.3530080-1-chenhuacai@loongson.cn
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

kernel/fail_function: fix memory leak with using debugfs_lookup()

[ Upstream commit 2bb3669f576559db273efe49e0e69f82450efbca ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.

Cc: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20230202151633.2310897-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drivers: base: dd: fix memory leak with using debugfs_lookup()

[ Upstream commit 36c893d3a759ae7c91ee7d4871ebfc7504f08c40 ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.

Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Link: https://lore.kernel.org/r/20230202141621.2296458-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drivers: base: component: fix memory leak with using debugfs_lookup()

[ Upstream commit 8deb87b1e810dd558371e88ffd44339fbef27870 ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.

Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Link: https://lore.kernel.org/r/20230202141621.2296458-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

misc: vmw_balloon: fix memory leak with using debugfs_lookup()

[ Upstream commit 209cdbd07cfaa4b7385bad4eeb47e5ec1887d33d ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic at
once.

Cc: Nadav Amit <namit@vmware.com>
Cc: VMware PV-Drivers Reviewers <pv-drivers@vmware.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230202141100.2291188-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tty: pcn_uart: fix memory leak with using debugfs_lookup()

[ Upstream commit 04a189c720aa2b6091442113ce9b9bc93552dff8 ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.

Cc: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230202141221.2293012-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: Distribute available resources for root buses, too

[ Upstream commit 7180c1d08639f28e63110ad35815f7a1785b8a19 ]

Previously we distributed spare resources only upon hot-add, so if the
initial root bus scan found devices that had not been fully configured by
the BIOS, we allocated only enough resources to cover what was then
present. If some of those devices were hotplug bridges, we did not leave
any additional resource space for future expansion.

Distribute the available resources for root buses, too, to make this work
the same way as the normal hotplug case.

A previous commit to do this was reverted due to a regression reported by
Jonathan Cameron:

  e96e27fc6f79 ("PCI: Distribute available resources for root buses, too")
  5632e2beaf9d ("Revert "PCI: Distribute available resources for root buses, too"")

This commit changes pci_bridge_resources_not_assigned() to work with
bridges that do not have all the resource windows programmed by the boot
firmware (previously we expected all I/O, memory and prefetchable memory
were programmed).

Link: https://bugzilla.kernel.org/show_bug.cgi?id=216000
Link: https://lore.kernel.org/r/20220905080232.36087-5-mika.westerberg@linux.intel.com
Link: https://lore.kernel.org/r/20230131092405.29121-4-mika.westerberg@linux.intel.com
Reported-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: Take other bus devices into account when distributing resources

[ Upstream commit 9db0b9b6a14249ef65a5f1e5e3b37762af96f425 ]

A PCI bridge may reside on a bus with other devices as well. The resource
distribution code does not take this into account and therefore it expands
the bridge resource windows too much, not leaving space for the other
devices (or functions of a multifunction device).  This leads to an issue
that Jonathan reported when running QEMU with the following topology (QEMU
parameters):

  -device pcie-root-port,port=0,id=root_port13,chassis=0,slot=2  \
  -device x3130-upstream,id=sw1,bus=root_port13,multifunction=on \
  -device e1000,bus=root_port13,addr=0.1                         \
  -device xio3130-downstream,id=fun1,bus=sw1,chassis=0,slot=3    \
  -device e1000,bus=fun1

The first e1000 NIC here is another function in the switch upstream port.
This leads to following errors:

  pci 0000:00:04.0: bridge window [mem 0x10200000-0x103fffff] to [bus 02-04]
  pci 0000:02:00.0: bridge window [mem 0x10200000-0x103fffff] to [bus 03-04]
  pci 0000:02:00.1: BAR 0: failed to assign [mem size 0x00020000]
  e1000 0000:02:00.1: can't ioremap BAR 0: [??? 0x00000000 flags 0x0]

Fix this by taking into account bridge windows, device BARs and SR-IOV PF
BARs on the bus (PF BARs include space for VF BARS so only account PF
BARs), including the ones belonging to bridges themselves if it has any.

Link: https://lore.kernel.org/linux-pci/20221014124553.0000696f@huawei.com/
Link: https://lore.kernel.org/linux-pci/6053736d-1923-41e7-def9-7585ce1772d9@ixsystems.com/
Link: https://lore.kernel.org/r/20230131092405.29121-3-mika.westerberg@linux.intel.com
Reported-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reported-by: Alexander Motin <mav@ixsystems.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: Align extra resources for hotplug bridges properly

[ Upstream commit 08f0a15ee8adb4846b08ca5d5c175fbf0f652bc9 ]

After division the extra resource space per hotplug bridge may not be
aligned according to the window alignment, so align it before passing it
down for further distribution.

Link: https://lore.kernel.org/r/20230131092405.29121-2-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: gadget: uvc: Make bSourceID read/write

[ Upstream commit b3c839bd8a07d303bc59a900d55dd35c7826562c ]

At the moment, the UVC function graph is hardcoded IT -> PU -> OT.
To add XU support we need the ability to insert the XU descriptors
into the chain. To facilitate that, make the output terminal's
bSourceID attribute writeable so that we can configure its source.

Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230206161802.892954-2-dan.scally@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: uvc: Enumerate valid values for color matching

[ Upstream commit e16cab9c1596e251761d2bfb5e1467950d616963 ]

The color matching descriptors defined in the UVC Specification
contain 3 fields with discrete numeric values representing particular
settings. Enumerate those values so that later code setting them can
be more readable.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230202114142.300858-2-dan.scally@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

USB: ene_usb6250: Allocate enough memory for full object

[ Upstream commit ce33e64c1788912976b61314b56935abd4bc97ef ]

The allocation of PageBuffer is 512 bytes in size, but the dereferencing
of struct ms_bootblock_idi (also size 512) happens at a calculated offset
within the allocation, which means the object could potentially extend
beyond the end of the allocation. Avoid this case by just allocating
enough space to catch any accesses beyond the end. Seen with GCC 13:

../drivers/usb/storage/ene_ub6250.c: In function 'ms_lib_process_bootblock':
../drivers/usb/storage/ene_ub6250.c:1050:44: warning: array subscript 'struct ms_bootblock_idi[0]' is partly outside array bounds of 'unsigned char[512]' [-Warray-bounds=]
 1050 |                         if (le16_to_cpu(idi->wIDIgeneralConfiguration) != MS_IDI_GENERAL_CONF)
      |                                            ^~
../include/uapi/linux/byteorder/little_endian.h:37:51: note: in definition of macro '__le16_to_cpu'
   37 | #define __le16_to_cpu(x) ((__force __u16)(__le16)(x))
      |                                                   ^
../drivers/usb/storage/ene_ub6250.c:1050:29: note: in expansion of macro 'le16_to_cpu'
 1050 |                         if (le16_to_cpu(idi->wIDIgeneralConfiguration) != MS_IDI_GENERAL_CONF)
      |                             ^~~~~~~~~~~
In file included from ../drivers/usb/storage/ene_ub6250.c:5:
In function 'kmalloc',
    inlined from 'ms_lib_process_bootblock' at ../drivers/usb/storage/ene_ub6250.c:942:15:
../include/linux/slab.h:580:24: note: at offset [256, 512] into object of size 512 allocated by 'kmalloc_trace'
  580 |                 return kmalloc_trace(
      |                        ^~~~~~~~~~~~~~
  581 |                                 kmalloc_caches[kmalloc_type(flags)][index],
      |                                 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  582 |                                 flags, size);
      |                                 ~~~~~~~~~~~~

Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230204183546.never.849-kees@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: host: xhci: mvebu: Iterate over array indexes instead of using pointer math

[ Upstream commit 0fbd2cda92cdb00f72080665554a586f88bca821 ]

Walking the dram->cs array was seen as accesses beyond the first array
item by the compiler. Instead, use the array index directly. This allows
for run-time bounds checking under CONFIG_UBSAN_BOUNDS as well. Seen
with GCC 13 with -fstrict-flex-arrays:

In function 'xhci_mvebu_mbus_config',
    inlined from 'xhci_mvebu_mbus_init_quirk' at ../drivers/usb/host/xhci-mvebu.c:66:2:
../drivers/usb/host/xhci-mvebu.c:37:28: warning: array subscript 0 is outside array bounds of 'const struct mbus_dram_window[0]' [-Warray-bounds=]
   37 |                 writel(((cs->size - 1) & 0xffff0000) | (cs->mbus_attr << 8) |
      |                          ~~^~~~~~

Cc: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230204183651.never.663-kees@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

USB: gadget: pxa27x_udc: fix memory leak with using debugfs_lookup()

[ Upstream commit 7a6952fa0366d4408eb8695af1a0578c39ec718a ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Link: https://lore.kernel.org/r/20230202153235.2412790-12-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

USB: gadget: pxa25x_udc: fix memory leak with using debugfs_lookup()

[ Upstream commit 7a038a681b7df78362d9fc7013e5395a694a9d3a ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Link: https://lore.kernel.org/r/20230202153235.2412790-11-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

USB: gadget: lpc32xx_udc: fix memory leak with using debugfs_lookup()

[ Upstream commit e3965acaf3739fde9d74ad82979b46d37c6c208f ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.

Cc: Jakob Koschel <jakobkoschel@gmail.com>
Cc: Miaoqian Lin <linmq006@gmail.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://lore.kernel.org/r/20230202153235.2412790-10-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

USB: gadget: bcm63xx_udc: fix memory leak with using debugfs_lookup()

[ Upstream commit a91c99b1fe5c6f7e52fb932ad9e57ec7cfe913ec ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.

Cc: Kevin Cernekee <cernekee@gmail.com>
Link: https://lore.kernel.org/r/20230202153235.2412790-9-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

USB: gadget: gr_udc: fix memory leak with using debugfs_lookup()

[ Upstream commit 73f4451368663ad28daa67980c6dd11d83b303eb ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.

Cc: Jakob Koschel <jakobkoschel@gmail.com>
Link: https://lore.kernel.org/r/20230202153235.2412790-8-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

USB: isp1362: fix memory leak with using debugfs_lookup()

[ Upstream commit c26e682afc14caa87d44beed271eec8991e93c65 ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.

Cc: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20230202153235.2412790-7-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

USB: isp116x: fix memory leak with using debugfs_lookup()

[ Upstream commit a95f62d5813facbec20ec087472eb313ee5fa8af ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.

Cc: Olav Kongas <ok@artecdesign.ee>
Link: https://lore.kernel.org/r/20230202153235.2412790-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

USB: fotg210: fix memory leak with using debugfs_lookup()

[ Upstream commit 6b4040f452037a7e95472577891d57c6b18c89c5 ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230202153235.2412790-5-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

USB: sl811: fix memory leak with using debugfs_lookup()

[ Upstream commit e1523c4dbc54e164638ff8729d511cf91e27be04 ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.

Cc: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20230202153235.2412790-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

USB: uhci: fix memory leak with using debugfs_lookup()

[ Upstream commit 0a3f82c79c86278e7f144564b1cb6cc5c3657144 ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.

Cc: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230202153235.2412790-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

USB: ULPI: fix memory leak with using debugfs_lookup()

[ Upstream commit 8f4d25eba599c4bd4b5ea8ae8752cda480a9d563 ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.

Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230202153235.2412790-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

USB: chipidea: fix memory leak with using debugfs_lookup()

[ Upstream commit ff35f3ea3baba5b81416ac02d005cfbf6dd182fa ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.

Cc: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230202153235.2412790-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

USB: dwc3: fix memory leak with using debugfs_lookup()

[ Upstream commit be308d68785b205e483b3a0c61ba3a82da468f2c ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.

Note, the root dentry for the debugfs directory for the device needs to
be saved so we don't have to keep looking it up, which required a bit
more refactoring to properly create and remove it when needed.

Reported-by: Bruce Chen <bruce.chen@unisoc.com>
Reported-by: Cixi Geng <cixi.geng1@unisoc.com>
Tested-by: Cixi Geng <gengcixi@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230202152820.2409908-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

staging: pi433: fix memory leak with using debugfs_lookup()

[ Upstream commit 2f36e789e540df6a9fbf471b3a2ba62a8b361586 ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.  This requires saving off the root directory dentry to make
creation of individual device subdirectories easier.

Cc: Paulo Miguel Almeida <paulo.miguel.almeida.rodenas@gmail.com>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Sidong Yang <realwakka@gmail.com>
Cc: Liu Shixin <liushixin2@huawei.com>
Cc: "Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230202141138.2291946-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: loongson: Prevent LS7A MRRS increases

[ Upstream commit 8b3517f88ff2983f52698893519227c10aac90b2 ]

Except for isochronous-configured devices, software may set
Max_Read_Request_Size (MRRS) to any value up to 4096.  If a device issues a
read request with size greater than the completer's Max_Payload_Size (MPS),
the completer is required to break the response into multiple completions.

Instead of correctly responding with multiple completions to a large read
request, some LS7A Root Ports respond with a Completer Abort.  To prevent
this, the MRRS must be limited to an implementation-specific value.

The OS cannot detect that value, so rely on BIOS to configure MRRS before
booting, and quirk the Root Ports so we never set an MRRS larger than that
BIOS value for any downstream device.

N.B. Hot-added devices are not configured by BIOS, and they power up with
MRRS = 512 bytes, so these devices will be limited to 512 bytes.  If the
LS7A limit is smaller, those hot-added devices may not work correctly, but
per [1], hotplug is not supported with this chipset revision.

[1] https://lore.kernel.org/r/073638a7-ae68-2847-ac3d-29e5e760d6af@loongson.cn

[bhelgaas: commit log]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216884
Link: https://lore.kernel.org/r/20230201043018.778499-3-chenhuacai@loongson.cn
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

soundwire: bus_type: Avoid lockdep assert in sdw_drv_probe()

[ Upstream commit 3dca1f89ae3455963d7b53245ecf298ea9bae857 ]

Don't hold sdw_dev_lock while calling the peripheral driver
probe() and remove() callbacks.

Holding sdw_dev_lock around the probe() and remove() calls causes
a theoretical mutex inversion which lockdep will assert on.

During probe() the sdw_dev_lock mutex is taken first and then
ASoC/ALSA locks are taken by the probe() implementation.

During normal operation ASoC can take its locks and then trigger
a runtime resume of the component. The SoundWire resume will then
take sdw_dev_lock. This is the reverse order compared to probe().

It's not necessary to hold sdw_dev_lock when calling the probe()
and remove(), it is only used to prevent the bus core calling the
driver callbacks if there isn't a driver or the driver is removing.

All calls to the driver callbacks are guarded by the 'probed' flag.
So if sdw_dev_lock is held while setting and clearing the 'probed'
flag this is sufficient to guarantee the safety of callback
functions.

Removing the mutex from around the call to probe() means that it
is now possible for a bus event (PING response) to be handled in
parallel with the probe(). But sdw_bus_probe() already has
handling for this by calling the device update_status() after
the probe() has completed.

Example lockdep assert:
[   46.098514] ======================================================
[   46.104736] WARNING: possible circular locking dependency detected
[   46.110961] 6.1.0-rc4-jamerson #1 Tainted: G            E
[   46.116842] ------------------------------------------------------
[   46.123063] mpg123/1130 is trying to acquire lock:
[   46.127883] ffff8b445031fb80 (&slave->sdw_dev_lock){+.+.}-{3:3}, at: sdw_update_slave_status+0x26/0x70
[   46.137225]
               but task is already holding lock:
[   46.143074] ffffffffc1455310 (&card->pcm_mutex){+.+.}-{3:3}, at: dpcm_fe_dai_open+0x49/0x830
[   46.151536]
               which lock already depends on the new lock.[   46.159732]
               the existing dependency chain (in reverse order) is:
[   46.167231]
               -> #4 (&card->pcm_mutex){+.+.}-{3:3}:
[   46.173428]        __mutex_lock+0x94/0x920
[   46.177542]        snd_soc_dpcm_runtime_update+0x2e/0x100
[   46.182958]        snd_soc_dapm_put_enum_double+0x1c2/0x200
[   46.188548]        snd_ctl_elem_write+0x10c/0x1d0
[   46.193268]        snd_ctl_ioctl+0x126/0x850
[   46.197556]        __x64_sys_ioctl+0x87/0xc0
[   46.201845]        do_syscall_64+0x38/0x90
[   46.205959]        entry_SYSCALL_64_after_hwframe+0x63/0xcd
[   46.211553]
               -> #3 (&card->controls_rwsem){++++}-{3:3}:
[   46.218188]        down_write+0x2b/0xd0
[   46.222038]        snd_ctl_add_replace+0x39/0xb0
[   46.226672]        snd_soc_add_controls+0x53/0x80
[   46.231393]        soc_probe_component+0x1e4/0x2a0
[   46.236202]        snd_soc_bind_card+0x51a/0xc80
[   46.240836]        devm_snd_soc_register_card+0x43/0x90
[   46.246079]        mc_probe+0x982/0xfe0 [snd_soc_sof_sdw]
[   46.251500]        platform_probe+0x3c/0xa0
[   46.255700]        really_probe+0xde/0x390
[   46.259814]        __driver_probe_device+0x78/0x180
[   46.264710]        driver_probe_device+0x1e/0x90
[   46.269347]        __driver_attach+0x9f/0x1f0
[   46.273721]        bus_for_each_dev+0x78/0xc0
[   46.278098]        bus_add_driver+0x1ac/0x200
[   46.282473]        driver_register+0x8f/0xf0
[   46.286759]        do_one_initcall+0x58/0x310
[   46.291136]        do_init_module+0x4c/0x1f0
[   46.295422]        __do_sys_finit_module+0xb4/0x130
[   46.300321]        do_syscall_64+0x38/0x90
[   46.304434]        entry_SYSCALL_64_after_hwframe+0x63/0xcd
[   46.310027]
               -> #2 (&card->mutex){+.+.}-{3:3}:
[   46.315883]        __mutex_lock+0x94/0x920
[   46.320000]        snd_soc_bind_card+0x3e/0xc80
[   46.324551]        devm_snd_soc_register_card+0x43/0x90
[   46.329798]        mc_probe+0x982/0xfe0 [snd_soc_sof_sdw]
[   46.335219]        platform_probe+0x3c/0xa0
[   46.339420]        really_probe+0xde/0x390
[   46.343532]        __driver_probe_device+0x78/0x180
[   46.348430]        driver_probe_device+0x1e/0x90
[   46.353065]        __driver_attach+0x9f/0x1f0
[   46.357437]        bus_for_each_dev+0x78/0xc0
[   46.361812]        bus_add_driver+0x1ac/0x200
[   46.366716]        driver_register+0x8f/0xf0
[   46.371528]        do_one_initcall+0x58/0x310
[   46.376424]        do_init_module+0x4c/0x1f0
[   46.381239]        __do_sys_finit_module+0xb4/0x130
[   46.386665]        do_syscall_64+0x38/0x90
[   46.391299]        entry_SYSCALL_64_after_hwframe+0x63/0xcd
[   46.397416]
               -> #1 (client_mutex){+.+.}-{3:3}:
[   46.404307]        __mutex_lock+0x94/0x920
[   46.408941]        snd_soc_add_component+0x24/0x2c0
[   46.414345]        devm_snd_soc_register_component+0x54/0xa0
[   46.420522]        cs35l56_common_probe+0x280/0x370 [snd_soc_cs35l56]
[   46.427487]        cs35l56_sdw_probe+0xf4/0x170 [snd_soc_cs35l56_sdw]
[   46.434442]        sdw_drv_probe+0x80/0x1a0
[   46.439136]        really_probe+0xde/0x390
[   46.443738]        __driver_probe_device+0x78/0x180
[   46.449120]        driver_probe_device+0x1e/0x90
[   46.454247]        __driver_attach+0x9f/0x1f0
[   46.459106]        bus_for_each_dev+0x78/0xc0
[   46.463971]        bus_add_driver+0x1ac/0x200
[   46.468825]        driver_register+0x8f/0xf0
[   46.473592]        do_one_initcall+0x58/0x310
[   46.478441]        do_init_module+0x4c/0x1f0
[   46.483202]        __do_sys_finit_module+0xb4/0x130
[   46.488572]        do_syscall_64+0x38/0x90
[   46.493158]        entry_SYSCALL_64_after_hwframe+0x63/0xcd
[   46.499229]
               -> #0 (&slave->sdw_dev_lock){+.+.}-{3:3}:
[   46.506737]        __lock_acquire+0x1121/0x1df0
[   46.511765]        lock_acquire+0xd5/0x300
[   46.516360]        __mutex_lock+0x94/0x920
[   46.520949]        sdw_update_slave_status+0x26/0x70
[   46.526409]        sdw_clear_slave_status+0xd8/0xe0
[   46.531783]        intel_resume_runtime+0x139/0x2a0
[   46.537155]        __rpm_callback+0x41/0x120
[   46.541919]        rpm_callback+0x5d/0x70
[   46.546422]        rpm_resume+0x531/0x7e0
[   46.550920]        __pm_runtime_resume+0x4a/0x80
[   46.556024]        snd_soc_pcm_component_pm_runtime_get+0x2f/0xc0
[   46.562611]        __soc_pcm_open+0x62/0x520
[   46.567375]        dpcm_be_dai_startup+0x116/0x210
[   46.572661]        dpcm_fe_dai_open+0xf7/0x830
[   46.577597]        snd_pcm_open_substream+0x54a/0x8b0
[   46.583145]        snd_pcm_open.part.0+0xdc/0x200
[   46.588341]        snd_pcm_playback_open+0x51/0x80
[   46.593625]        chrdev_open+0xc0/0x250
[   46.598129]        do_dentry_open+0x15f/0x430
[   46.602981]        path_openat+0x75e/0xa80
[   46.607575]        do_filp_open+0xb2/0x160
[   46.612162]        do_sys_openat2+0x9a/0x160
[   46.616922]        __x64_sys_openat+0x53/0xa0
[   46.621767]        do_syscall_64+0x38/0x90
[   46.626352]        entry_SYSCALL_64_after_hwframe+0x63/0xcd
[   46.632414]
               other info that might help us debug this:[   46.641862] Chain exists of:
                 &slave->sdw_dev_lock --> &card->controls_rwsem --> &card->pcm_mutex[   46.655145]  Possible unsafe locking scenario:[   46.662048]        CPU0                    CPU1
[   46.667080]        ----                    ----
[   46.672108]   lock(&card->pcm_mutex);
[   46.676267]                                lock(&card->controls_rwsem);
[   46.683382]                                lock(&card->pcm_mutex);
[   46.690063]   lock(&slave->sdw_dev_lock);
[   46.694574]
                *** DEADLOCK ***[   46.701942] 2 locks held by mpg123/1130:
[   46.706356]  #0: ffff8b4457b22b90 (&pcm->open_mutex){+.+.}-{3:3}, at: snd_pcm_open.part.0+0xc9/0x200
[   46.715999]  #1: ffffffffc1455310 (&card->pcm_mutex){+.+.}-{3:3}, at: dpcm_fe_dai_open+0x49/0x830
[   46.725390]
               stack backtrace:
[   46.730752] CPU: 0 PID: 1130 Comm: mpg123 Tainted: G            E      6.1.0-rc4-jamerson #1
[   46.739703] Hardware name: AAEON UP-WHL01/UP-WHL01, BIOS UPW1AM19 11/10/2020
[   46.747270] Call Trace:
[   46.750239]  <TASK>
[   46.752857]  dump_stack_lvl+0x56/0x73
[   46.757045]  check_noncircular+0x102/0x120
[   46.761664]  __lock_acquire+0x1121/0x1df0
[   46.766197]  lock_acquire+0xd5/0x300
[   46.770292]  ? sdw_update_slave_status+0x26/0x70
[   46.775432]  ? lock_is_held_type+0xe2/0x140
[   46.780143]  __mutex_lock+0x94/0x920
[   46.784241]  ? sdw_update_slave_status+0x26/0x70
[   46.789387]  ? find_held_lock+0x2b/0x80
[   46.793750]  ? sdw_update_slave_status+0x26/0x70
[   46.798894]  ? lock_release+0x147/0x2f0
[   46.803262]  ? lockdep_init_map_type+0x47/0x250
[   46.808315]  ? sdw_update_slave_status+0x26/0x70
[   46.813456]  sdw_update_slave_status+0x26/0x70
[   46.818422]  sdw_clear_slave_status+0xd8/0xe0
[   46.823302]  ? pm_generic_runtime_suspend+0x30/0x30
[   46.828706]  intel_resume_runtime+0x139/0x2a0
[   46.833583]  ? _raw_spin_unlock_irq+0x24/0x50
[   46.838462]  ? pm_generic_runtime_suspend+0x30/0x30
[   46.843866]  __rpm_callback+0x41/0x120
[   46.848142]  ? pm_generic_runtime_suspend+0x30/0x30
[   46.853550]  rpm_callback+0x5d/0x70
[   46.857568]  rpm_resume+0x531/0x7e0
[   46.861578]  ? _raw_spin_lock_irqsave+0x62/0x70
[   46.866634]  __pm_runtime_resume+0x4a/0x80
[   46.871258]  snd_soc_pcm_component_pm_runtime_get+0x2f/0xc0
[   46.877358]  __soc_pcm_open+0x62/0x520
[   46.881634]  ? dpcm_add_paths.isra.0+0x35d/0x4c0
[   46.886784]  dpcm_be_dai_startup+0x116/0x210
[   46.891592]  dpcm_fe_dai_open+0xf7/0x830
[   46.896046]  ? debug_mutex_init+0x33/0x50
[   46.900591]  snd_pcm_open_substream+0x54a/0x8b0
[   46.905658]  snd_pcm_open.part.0+0xdc/0x200
[   46.910376]  ? wake_up_q+0x90/0x90
[   46.914312]  snd_pcm_playback_open+0x51/0x80
[   46.919118]  chrdev_open+0xc0/0x250
[   46.923147]  ? cdev_device_add+0x90/0x90
[   46.927608]  do_dentry_open+0x15f/0x430
[   46.931976]  path_openat+0x75e/0xa80
[   46.936086]  do_filp_open+0xb2/0x160
[   46.940194]  ? lock_release+0x147/0x2f0
[   46.944563]  ? _raw_spin_unlock+0x29/0x50
[   46.949101]  do_sys_openat2+0x9a/0x160
[   46.953377]  __x64_sys_openat+0x53/0xa0
[   46.957733]  do_syscall_64+0x38/0x90
[   46.961829]  entry_SYSCALL_64_after_hwframe+0x63/0xcd
[   46.967402] RIP: 0033:0x7fa6397ccd3b
[   46.971506] Code: 25 00 00 41 00 3d 00 00 41 00 74 4b 64 8b 04 25 18 00 00 00 85 c0 75 67 44 89 e2 48 89 ee bf 9c ff ff ff b8 01 01 00 00 0f 05 <48> 3d 00 f0 ff ff 0f 87 91 00 00 00 48 8b 4c 24 28 64 48 33 0c 25
[   46.991413] RSP: 002b:00007fff838e8990 EFLAGS: 00000246 ORIG_RAX: 0000000000000101
[   46.999580] RAX: ffffffffffffffda RBX: 0000000000080802 RCX: 00007fa6397ccd3b
[   47.007311] RDX: 0000000000080802 RSI: 00007fff838e8b50 RDI: 00000000ffffff9c
[   47.015047] RBP: 00007fff838e8b50 R08: 0000000000000000 R09: 0000000000000011
[   47.022787] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000080802
[   47.030539] R13: 0000000000000004 R14: 0000000000000000 R15: 00007fff838e8b50
[   47.038289]  </TASK>

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230123172520.339367-1-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: uvcvideo: Add GUID for BGRA/X 8:8:8:8

[ Upstream commit 015d44c2b700ba9639dd29672ba362796cc0be54 ]

The Cypress EZUSB FX3 UVC example can be configured to report pixel
format "e436eb7e-524f-11ce-9f53-0020af0ba770". This is its GUID for
BGRA/X 8:8:8:8.

The UVC 1.5 spec [1] only defines GUIDs for YUY2, NV12, M420 and I420.
This seems to be an extension documented in the Microsoft Windows Media
Format SDK[2]. This Media Format SDK defines this GUID as corresponding
to `MEDIASUBTYPE_RGB32`, which is confirmed by [4] as `MEDIASUBTYPE_ARGB32`
has different GUID.

Note that in my case, the FX3 UVC can output either channel order,
BGR or RGB or any other mix for that matter. Since Linux commit
1b8dc32286a1a ("[media] uvcvideo: Add GUID for BGR 8:8:8")
defined a GUID for `MEDIASUBTYPE_RGB24` channel order as BGR, keep
this change consistent and define `MEDIASUBTYPE_RGB32` as BGR as well.
Document [3] also indicates the channel order is BGR.

[1] https://www.usb.org/document-library/video-class-v15-document-set
[2] https://learn.microsoft.com/en-us/windows/win32/wmformat/media-type-identifiers
[3] https://learn.microsoft.com/en-us/windows/win32/directshow/uncompressed-rgb-video-subtypes
[4] https://gix.github.io/media-types/

Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ricardo@ribalda.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20230126231456.3402323-2-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iio: accel: mma9551_core: Prevent uninitialized variable in mma9551_read_config_word()

[ Upstream commit 64a68158738ec8f520347144352f7a09bdb9e169 ]

Smatch Warns:
drivers/iio/accel/mma9551_core.c:299
mma9551_read_config_word() error: uninitialized symbol 'v'.

When (offset >= 1 << 12) is true mma9551_transfer() will return -EINVAL
without 'v' being initialized, so check for the error and return.

Note: No actual bug as caller checks the return value and does not
use the parameter in the problem case.

Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20230126153610.3586243-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iio: accel: mma9551_core: Prevent uninitialized variable in mma9551_read_status_word()

[ Upstream commit e56d2c34ce9dc122b1a618172ec0e05e50adb9e9 ]

Smatch Warns: drivers/iio/accel/mma9551_core.c:357
mma9551_read_status_word() error: uninitialized symbol 'v'.

When (offset >= 1 << 12) is true mma9551_transfer() will return -EINVAL
without 'v' being initialized, so check for the error and return.

Note: Not a bug as such because the caller checks return value and
doesn't not use this parameter in the problem case.

Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20230126152147.3585874-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bus: mhi: ep: Fix the debug message for MHI_PKT_TYPE_RESET_CHAN_CMD cmd

[ Upstream commit 8e697fcfdb9809634e268058ca743369c216b7ac ]

The debug log incorrectly mentions that STOP command is received instead of
RESET command. Fix that.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/20221228161704.255268-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tools/iio/iio_utils:fix memory leak

[ Upstream commit f2edf0c819a4823cd6c288801ce737e8d4fcde06 ]

1. fopen sysfs without fclose.
2. asprintf filename without free.
3. if asprintf return error,do not need to free the buffer.

Signed-off-by: Yulong Zhang <yulong.zhang@metoak.net>
Link: https://lore.kernel.org/r/20230117025147.69890-1-yulong.zhang@metoak.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mei: bus-fixup:upon error print return values of send and receive

[ Upstream commit 4b8659e2c258e4fdac9ccdf06cc20c0677894ef9 ]

For easier debugging, upon error, print also return values
from __mei_cl_recv() and __mei_cl_send() functions.

Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20221212214933.275434-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

serial: sc16is7xx: setup GPIO controller later in probe

[ Upstream commit c8f71b49ee4d28930c4a6798d1969fa91dc4ef3e ]

The GPIO controller component of the sc16is7xx driver is setup too
early, which can result in a race condition where another device tries
to utilise the GPIO lines before the sc16is7xx device has finished
initialising.

This issue manifests itself as an Oops when the GPIO lines are configured:

    Unable to handle kernel read from unreadable memory at virtual address
    ...
    pc : sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx]
    lr : sc16is7xx_gpio_direction_output+0x4c/0x108 [sc16is7xx]
    ...
    Call trace:
    sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx]
    gpiod_direction_output_raw_commit+0x64/0x318
    gpiod_direction_output+0xb0/0x170
    create_gpio_led+0xec/0x198
    gpio_led_probe+0x16c/0x4f0
    platform_drv_probe+0x5c/0xb0
    really_probe+0xe8/0x448
    driver_probe_device+0xe8/0x138
    __device_attach_driver+0x94/0x118
    bus_for_each_drv+0x8c/0xe0
    __device_attach+0x100/0x1b8
    device_initial_probe+0x28/0x38
    bus_probe_device+0xa4/0xb0
    deferred_probe_work_func+0x90/0xe0
    process_one_work+0x1c4/0x480
    worker_thread+0x54/0x430
    kthread+0x138/0x150
    ret_from_fork+0x10/0x1c

This patch moves the setup of the GPIO controller functions to later in the
probe function, ensuring the sc16is7xx device has already finished
initialising by the time other devices try to make use of the GPIO lines.
The error handling has also been reordered to reflect the new
initialisation order.

Co-developed-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Isaac True <isaac.true@canonical.com>
Link: https://lore.kernel.org/r/20221130105529.698385-1-isaac.true@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tty: serial: fsl_lpuart: disable the CTS when send break signal

[ Upstream commit c4c81db5cf8bc53d6160c3abf26d382c841aa434 ]

LPUART IP has a bug that it treats the CTS as higher priority than the
break signal, which cause the break signal sending through UARTCTRL_SBK
may impacted by the CTS input if the HW flow control is enabled.

Add this workaround patch to fix the IP bug, we can disable CTS before
asserting SBK to avoid any interference from CTS, and re-enable it when
break off.

Such as for the bluetooth chip power save feature, host can let the BT
chip get into sleep state by sending a UART break signal, and wake it up
by turning off the UART break. If the BT chip enters the sleep mode
successfully, it will pull up the CTS line, if the BT chip is woken up,
it will pull down the CTS line. If without this workaround patch, the
UART TX pin cannot send the break signal successfully as it affected by
the BT CTS pin. After adding this patch, the BT power save feature can
work well.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221214031137.28815-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tty: fix out-of-bounds access in tty_driver_lookup_tty()

[ Upstream commit db4df8e9d79e7d37732c1a1b560958e8dadfefa1 ]

When specifying an invalid console= device like console=tty3270,
tty_driver_lookup_tty() returns the tty struct without checking
whether index is a valid number.

To reproduce:

qemu-system-x86_64 -enable-kvm -nographic -serial mon:stdio \
-kernel ../linux-build-x86/arch/x86/boot/bzImage \
-append "console=ttyS0 console=tty3270"

This crashes with:

[    0.770599] BUG: kernel NULL pointer dereference, address: 00000000000000ef
[    0.771265] #PF: supervisor read access in kernel mode
[    0.771773] #PF: error_code(0x0000) - not-present page
[    0.772609] Oops: 0000 [#1] PREEMPT SMP PTI
[    0.774878] RIP: 0010:tty_open+0x268/0x6f0
[    0.784013]  chrdev_open+0xbd/0x230
[    0.784444]  ? cdev_device_add+0x80/0x80
[    0.784920]  do_dentry_open+0x1e0/0x410
[    0.785389]  path_openat+0xca9/0x1050
[    0.785813]  do_filp_open+0xaa/0x150
[    0.786240]  file_open_name+0x133/0x1b0
[    0.786746]  filp_open+0x27/0x50
[    0.787244]  console_on_rootfs+0x14/0x4d
[    0.787800]  kernel_init_freeable+0x1e4/0x20d
[    0.788383]  ? rest_init+0xc0/0xc0
[    0.788881]  kernel_init+0x11/0x120
[    0.789356]  ret_from_fork+0x22/0x30

Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221209112737.3222509-2-svens@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

staging: emxx_udc: Add checks for dma_alloc_coherent()

[ Upstream commit f6510a93cfd8c6c79b4dda0f2967cdc6df42eff4 ]

As the dma_alloc_coherent may return NULL, the return value needs to be
checked to avoid NULL poineter dereference.

Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Link: https://lore.kernel.org/r/20230119083119.16956-1-yuancan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

cacheinfo: Fix shared_cpu_map to handle shared caches at different levels

[ Upstream commit 198102c9103fc78d8478495971947af77edb05c1 ]

The cacheinfo sets up the shared_cpu_map by checking whether the caches
with the same index are shared between CPUs. However, this will trigger
slab-out-of-bounds access if the CPUs do not have the same cache hierarchy.
Another problem is the mismatched shared_cpu_map when the shared cache does
not have the same index between CPUs.

CPU0 I D L3
index 0 1 2 x
^ ^ ^ ^
index 0 1 2 3
CPU1 I D L2 L3

This patch checks each cache is shared with all caches on other CPUs.

Reviewed-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Link: https://lore.kernel.org/r/20230117105133.4445-2-yongxuan.wang@sifive.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

USB: fix memory leak with using debugfs_lookup()

[ Upstream commit 30374434edab20e25776f8ecb4bc9d1e54309487 ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic at
once.

Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Jilin Yuan <yuanjilin@cdjrlc.com>
Link: https://lore.kernel.org/r/20230106152828.3790902-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: uvcvideo: Silence memcpy() run-time false positive warnings

[ Upstream commit b839212988575c701aab4d3d9ca15e44c87e383c ]

The memcpy() in uvc_video_decode_meta() intentionally copies across the
length and flags members and into the trailing buf flexible array.
Split the copy so that the compiler can better reason about (the lack
of) buffer overflows here. Avoid the run-time false positive warning:

  memcpy: detected field-spanning write (size 12) of single field "&meta->length" at drivers/media/usb/uvc/uvc_video.c:1355 (size 1)

Additionally fix a typo in the documentation for struct uvc_meta_buf.

Reported-by: ionut_n2001@yahoo.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216810
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: uvcvideo: Quirk for autosuspend in Logitech B910 and C910

[ Upstream commit 136effa754b57632f99574fc4a3433e0cfc031d9 ]

Logitech B910 and C910 firmware are unable to recover from a USB
autosuspend. When it resumes, the device is in a state where it only
produces invalid frames. Eg:

$ echo 0xFFFF > /sys/module/uvcvideo/parameters/trace # enable verbose log
$ yavta -c1 -n1 --file='frame#.jpg' --format MJPEG --size=1920x1080 /dev/video1
[350438.435219] uvcvideo: uvc_v4l2_open
[350438.529794] uvcvideo: Resuming interface 2
[350438.529801] uvcvideo: Resuming interface 3
[350438.529991] uvcvideo: Trying format 0x47504a4d (MJPG): 1920x1080.
[350438.529996] uvcvideo: Using default frame interval 33333.3 us (30.0 fps).
[350438.551496] uvcvideo: uvc_v4l2_mmap
[350438.555890] uvcvideo: Device requested 3060 B/frame bandwidth.
[350438.555896] uvcvideo: Selecting alternate setting 11 (3060 B/frame bandwidth).
[350438.556362] uvcvideo: Allocated 5 URB buffers of 32x3060 bytes each.
[350439.316468] uvcvideo: Marking buffer as bad (error bit set).
[350439.316475] uvcvideo: Frame complete (EOF found).
[350439.316477] uvcvideo: EOF in empty payload.
[350439.316484] uvcvideo: frame 1 stats: 149/261/417 packets, 1/149/417 pts (early initial), 416/417 scr, last pts/stc/sof 2976325734/2978107243/249
[350439.384510] uvcvideo: Marking buffer as bad (error bit set).
[350439.384516] uvcvideo: Frame complete (EOF found).
[350439.384518] uvcvideo: EOF in empty payload.
[350439.384525] uvcvideo: frame 2 stats: 265/379/533 packets, 1/265/533 pts (early initial), 532/533 scr, last pts/stc/sof 2979524454/2981305193/316
[350439.448472] uvcvideo: Marking buffer as bad (error bit set).
[350439.448478] uvcvideo: Frame complete (EOF found).
[350439.448480] uvcvideo: EOF in empty payload.
[350439.448487] uvcvideo: frame 3 stats: 265/377/533 packets, 1/265/533 pts (early initial), 532/533 scr, last pts/stc/sof 2982723174/2984503144/382
...(loop)...

The devices can leave this invalid state if the alternate setting of
the streaming interface is toggled.

This patch adds a quirk for this device so it can be autosuspended
properly.

lsusb -v:
Bus 001 Device 049: ID 046d:0821 Logitech, Inc. HD Webcam C910
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass          239 Miscellaneous Device
  bDeviceSubClass         2
  bDeviceProtocol         1 Interface Association
  bMaxPacketSize0        64
  idVendor           0x046d Logitech, Inc.
  idProduct          0x0821 HD Webcam C910
  bcdDevice            0.10
  iManufacturer           0
  iProduct                0
  iSerial                 1 390022B0
  bNumConfigurations      1

Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: uvcvideo: Handle errors from calls to usb_string

[ Upstream commit 4867bb590ae445bcfaa711a86b603c97e94574b3 ]

On a Webcam from Quanta, we see the following error.

usb 3-5: New USB device found, idVendor=0408, idProduct=30d2, bcdDevice= 0.03
usb 3-5: New USB device strings: Mfr=3, Product=1, SerialNumber=2
usb 3-5: Product: USB2.0 HD UVC WebCam
usb 3-5: Manufacturer: Quanta
usb 3-5: SerialNumber: 0x0001
...
uvcvideo: Found UVC 1.10 device USB2.0 HD UVC WebCam (0408:30d2)
uvcvideo: Failed to initialize entity for entity 5
uvcvideo: Failed to register entities (-22).

The Webcam reports an entity of type UVC_VC_EXTENSION_UNIT. It reports a
string index of '7' associated with that entity. The attempt to read that
string from the camera fails with error -32 (-EPIPE). usb_string() returns
that error, but it is ignored. As result, the entity name is empty. This
later causes v4l2_device_register_subdev() to return -EINVAL, and no
entities are registered as result.

While this appears to be a firmware problem with the camera, the kernel
should still handle the situation gracefully. To do that, check the return
value from usb_string(). If it reports an error, assign the entity's
default name.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: uvcvideo: Handle cameras with invalid descriptors

[ Upstream commit 41ddb251c68ac75c101d3a50a68c4629c9055e4c ]

If the source entity does not contain any pads, do not create a link.

Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: uvcvideo: Remove format descriptions

[ Upstream commit 50459f103edfe47c9a599d766a850ef6014936c5 ]

The V4L2 core overwrites format descriptions in v4l_fill_fmtdesc(),
there's no need to manually set the descriptions in the driver. This
prepares for removal of the format descriptions from the uvc_fmts table.

Unlike V4L2, UVC makes a distinction between the SD-DV, SDL-DV and HD-DV
formats. It also indicates whether the DV format uses 50Hz or 60Hz. This
information is parsed by the driver to construct a format name string
that is printed in a debug message, but serves no other purpose as V4L2
has a single V4L2_PIX_FMT_DV pixel format that covers all those cases.

As the information is available in the UVC descriptors, and thus
accessible to users with lsusb if they really care, don't log it in a
debug message and drop the format name string to simplify the code.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI/ACPI: Account for _S0W of the target bridge in acpi_pci_bridge_d3()

[ Upstream commit 8133844a8f2434be9576850c6978179d7cca5c81 ]

It is questionable to allow a PCI bridge to go into D3 if it has _S0W
returning D2 or a shallower power state, so modify acpi_pci_bridge_d3(() to
always take the return value of _S0W for the target bridge into account.
That is, make it return 'false' if _S0W returns D2 or a shallower power
state for the target bridge regardless of its ancestor Root Port
properties.  Of course, this also causes 'false' to be returned if the Root
Port itself is the target and its _S0W returns D2 or a shallower power
state.

However, still allow bridges without _S0W that are power-manageable via
ACPI to enter D3 to retain the current code behavior in that case.

This fixes problems where a hotplug notification is missed because a bridge
is in D3.  That means hot-added devices such as USB4 docks (and the devices
they contain) and Thunderbolt 3 devices may not work.

Link: https://lore.kernel.org/linux-pci/20221031223356.32570-1-mario.limonciello@amd.com/
Link: https://lore.kernel.org/r/12155458.O9o76ZdvQC@kreacher
Reported-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iommu/amd: Fix error handling for pdev_pri_ats_enable()

[ Upstream commit 080920e52148b4fbbf9360d5345fdcd7846e4841 ]

Current code throws kernel warning if it fails to enable pasid/pri [1].
Do not call pci_disable_[pasid/pri] if pci_enable_[pasid/pri] failed.

[1] https://lore.kernel.org/linux-iommu/15d0f9ff-2a56-b3e9-5b45-e6b23300ae3b@leemhuis.info/

Reported-by: Matt Fagnani <matt.fagnani@bell.net>
Signed-off-by: Vasant Hegde <vasant.hegde@amd.com>
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20230111121503.5931-1-vasant.hegde@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

IB/hfi1: Update RMT size calculation

[ Upstream commit 892ede5a77f337831609fb9c248ac60948061894 ]

Fix possible RMT overflow:  Use the correct netdev size.
Don't allow adjusted user contexts to go negative.

Fix QOS calculation: Send kernel context count as an argument since
dd->n_krcv_queues is not yet set up in earliest call.  Do not include
the control context in the QOS calculation.  Use the same sized
variable to find the max of krcvq[] entries.

Update the RMT count explanation to make more sense.

Signed-off-by: Dean Luick <dean.luick@cornelisnetworks.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Link: https://lore.kernel.org/r/167329106946.1472990.18385495251650939054.stgit@awfm-02.cornelisnetworks.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mfd: arizona: Use pm_runtime_resume_and_get() to prevent refcnt leak

[ Upstream commit 4414a7ab80cebf715045e3c4d465feefbad21139 ]

In arizona_clk32k_enable(), we should use pm_runtime_resume_and_get()
as pm_runtime_get_sync() will increase the refcnt even when it
returns an error.

Signed-off-by: Liang He <windhl@126.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230105061055.1509261-1-windhl@126.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

bootconfig: Increase max nodes of bootconfig from 1024 to 8192 for DCC support

[ Upstream commit 6c40624930c58529185a257380442547580ed837 ]

The Data Capture and Compare(DCC) is a debugging tool that uses the bootconfig
for configuring the register values during boot-time. Increase the max nodes
supported by bootconfig to cater to the requirements of the Data Capture and
Compare Driver.

Link: https://lore.kernel.org/all/1674536682-18404-1-git-send-email-quic_schowdhu@quicinc.com/
Signed-off-by: Souradeep Chowdhury <quic_schowdhu@quicinc.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

firmware/efi sysfb_efi: Add quirk for Lenovo IdeaPad Duet 3

[ Upstream commit e1d447157f232c650e6f32c9fb89ff3d0207c69a ]

Another Lenovo convertable which reports a landscape resolution of
1920x1200 with a pitch of (1920 * 4) bytes, while the actual framebuffer
has a resolution of 1200x1920 with a pitch of (1200 * 4) bytes.

Signed-off-by: Darrell Kavanagh <darrell.kavanagh@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

kernel/printk/index.c: fix memory leak with using debugfs_lookup()

[ Upstream commit 55bf243c514553e907efcf2bda92ba090eca8c64 ]

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.

Cc: Chris Down <chris@chrisdown.name>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20230202151411.2308576-1-gregkh@linuxfoundation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

tracing: Add NULL checks for buffer in ring_buffer_free_read_page()

[ Upstream commit 3e4272b9954094907f16861199728f14002fcaf6 ]

In a previous commit 7433632c9ff6, buffer, buffer->buffers and
buffer->buffers[cpu] in ring_buffer_wake_waiters() can be NULL,
and thus the related checks are added.

However, in the same call stack, these variables are also used in
ring_buffer_free_read_page():

tracing_buffers_release()
  ring_buffer_wake_waiters(iter->array_buffer->buffer)
    cpu_buffer = buffer->buffers[cpu] -> Add checks by previous commit
  ring_buffer_free_read_page(iter->array_buffer->buffer)
    cpu_buffer = buffer->buffers[cpu] -> No check

Thus, to avod possible null-pointer derefernces, the related checks
should be added.

These results are reported by a static tool designed by myself.

Link: https://lkml.kernel.org/r/20230113125501.760324-1-baijiaju1990@gmail.com
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

thermal: intel: BXT_PMIC: select REGMAP instead of depending on it

[ Upstream commit 1467fb960349dfa5e300658f1a409dde2cfb0c51 ]

REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.

Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.

Therefore, change the use of "depends on REGMAP" to "select REGMAP".

Fixes: b474303ffd57 ("thermal: add Intel BXT WhiskeyCove PMIC thermal driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

thermal: intel: quark_dts: fix error pointer dereference

[ Upstream commit f1b930e740811d416de4d2074da48b6633a672c8 ]

If alloc_soc_dts() fails, then we can just return.  Trying to free
"soc_dts" will lead to an Oops.

Fixes: 8c1876939663 ("thermal: intel Quark SoC X1000 DTS thermal driver")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: mediatek: mt8195: add missing initialization

[ Upstream commit b56ec2992a2e43bc3e60d6db86849d31640e791f ]

In etdm dai driver, dai_etdm_parse_of() function is used to parse dts
properties to get parameters. There are two for-loops which are
sepearately for all etdm and etdm input only cases. In etdm in only
loop, dai_id is not initialized, so it keeps the value intiliazed in
another loop.

In the patch, add the missing initialization to fix the unexpected
parsing problem.

Fixes: 1de9a54acafb ("ASoC: mediatek: mt8195: support etdm in platform driver")
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230301110200.26177-3-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: zl38060 add gpiolib dependency

[ Upstream commit 0de2cc3707b6b6e2ad40bd24ce09a5c1f65d01e1 ]

Without gpiolib, this driver fails to link:

arm-linux-gnueabi-ld: sound/soc/codecs/zl38060.o: in function `chip_gpio_get':
zl38060.c:(.text+0x30): undefined reference to `gpiochip_get_data'
arm-linux-gnueabi-ld: sound/soc/codecs/zl38060.o: in function `zl38_spi_probe':
zl38060.c:(.text+0xa18): undefined reference to `devm_gpiochip_add_data_with_key'

This appears to have been in the driver since the start, but is hard to
hit in randconfig testing since gpiolib is almost always selected by something
else.

Fixes: 52e8a94baf90 ("ASoC: Add initial ZL38060 driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230227085850.2503725-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvme-fabrics: show well known discovery name

[ Upstream commit 26a57cb35548ae67c14871cccbf50da3edb01ea4 ]

The kernel always logs the unique subsystem name for a discovery
controller, even in the case user space asked for the well known.

This has lead to confusion as the logs of nvme-cli and the kernel
logs didn't match.

First, nvme-cli connects to the well known discovery controller to
figure out if it supports TP8013. If so then nvme-cli disconnects and
connects to the unique discovery controller. Currently, the kernel show
that user space connected twice to the unique one.

To avoid further confusion, show the well known discovery controller if
user space asked for it:

  $ nvme connect-all -v -t tcp -a 192.168.0.1
  nvme0: nqn.2014-08.org.nvmexpress.discovery connected
  nvme0: nqn.2014-08.org.nvmexpress.discovery disconnected
  nvme0: nqn.discovery connected

  kernel log:
  nvme nvme0: new ctrl: NQN "nqn.2014-08.org.nvmexpress.discovery", addr 192.168.0.1:8009
  nvme nvme0: Removing ctrl: NQN "nqn.2014-08.org.nvmexpress.discovery"
  nvme nvme0: new ctrl: NQN "nqn.discovery", addr 192.168.0.1:8009

Fixes: e5ea42faa773 ("nvme: display correct subsystem NQN")
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvme-tcp: don't access released socket during error recovery

[ Upstream commit 76d54bf20cdcc1ed7569a89885e09636e9a8d71d ]

While the error recovery work is temporarily failing reconnect attempts,
running the 'nvme list' command causes a kernel NULL pointer dereference
by calling getsockname() with a released socket.

During error recovery work, the nvme tcp socket is released and a new one
created, so it is not safe to access the socket without proper check.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Fixes: 02c57a82c008 ("nvme-tcp: print actual source IP address through sysfs "address" attr")
Reviewed-by: Martin Belanger <martin.belanger@dell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvme: bring back auto-removal of deleted namespaces during sequential scan

[ Upstream commit 0dd6fff2aad4e35633fef1ea72838bec5b47559a ]

Bring back the check of the Identify Namespace return value for the
legacy NVMe 1.0-style sequential scanning.  While NVMe 1.0 does not
support namespace management, there are "modern" cloud solutions like
Google Cloud Platform that claim the obsolete 1.0 compliance for no
good reason while supporting proprietary sideband namespace management.

Fixes: 1a893c2bfef4 ("nvme: refactor namespace probing")
Reported-by: Nils Hanke <nh@edgeless.systems>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Tested-by: Nils Hanke <nh@edgeless.systems>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: apple: mca: Improve handling of unavailable DMA channels

[ Upstream commit fb1847cc460c127b12720119eae5f438ffc62e85 ]

When we fail to obtain a DMA channel, don't return a blanket -EINVAL,
instead return the original error code if there's one. This makes
deferring work as it should. Also don't print an error message for
-EPROBE_DEFER.

Fixes: 4ec8179c212f ("ASoC: apple: mca: Postpone requesting of DMA channels")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20230224153302.45365-3-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: apple: mca: Fix SERDES reset sequence

[ Upstream commit d8b3e396088d787771f19fd3b7949e080dc31d6f ]

Fix the reset sequence of reads and writes that we invoke from within
the early trigger. It looks like there never was a SERDES_CONF_SOME_RST
bit that should be involved in the reset sequence, and its presence in
the driver code is a mistake from earlier.

Instead, the reset sequence should go as follows: We should switch the
the SERDES unit's SYNC_SEL mux to the value of 7 (so outside the range
of 1...6 representing cluster's SYNCGEN units), then raise the RST bit
in SERDES_STATUS and wait for it to clear.

Properly resetting the SERDES unit fixes frame desynchronization hazard
in case of long frames (longer than 4 used slots). The desynchronization
manifests itself by rotating the PCM channels.

Fixes: 3df5d0d97289 ("ASoC: apple: mca: Start new platform driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20230224153302.45365-2-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: apple: mca: Fix final status read on SERDES reset

[ Upstream commit aaf5f0d76b6e1870e3674408de2b13a92a4d4059 ]

From within the early trigger we are doing a reset of the SERDES unit,
but the final status read is on a bad address. Add the missing SERDES
unit offset in calculation of the address.

Fixes: 3df5d0d97289 ("ASoC: apple: mca: Start new platform driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20230224153302.45365-1-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: adau7118: don't disable regulators on device unbind

[ Upstream commit b5bfa7277ee7d944421e0ef193586c6e34d7492c ]

The regulators are supposed to be controlled through the
set_bias_level() component callback. Moreover, the regulators are not
enabled during probe and so, this would lead to a regulator unbalanced
use count.

Fixes: ca514c0f12b02 ("ASOC: Add ADAU7118 8 Channel PDM-to-I2S/TDM Converter driver")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230224104551.1139981-1-nuno.sa@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

loop: loop_set_status_from_info() check before assignment

[ Upstream commit 9f6ad5d533d1c71e51bdd06a5712c4fbc8768dfa ]

In loop_set_status_from_info(), lo->lo_offset and lo->lo_sizelimit should
be checked before reassignment, because if an overflow error occurs, the
original correct value will be changed to the wrong value, and it will not
be changed back.

More, the original patch did not solve the problem, the value was set and
ioctl returned an error, but the subsequent io used the value in the loop
driver, which still caused an alarm:

loop_handle_cmd
 do_req_filebacked
  loff_t pos = ((loff_t) blk_rq_pos(rq) << 9) + lo->lo_offset;
  lo_rw_aio
   cmd->iocb.ki_pos = pos

Fixes: c490a0b5a4f3 ("loop: Check for overflow while configuring loop")
Signed-off-by: Zhong Jinghua <zhongjinghua@huawei.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20230221095027.3656193-1-zhongjinghua@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

io_uring: fix size calculation when registering buf ring

[ Upstream commit 48ba08374e779421ca34bd14b4834aae19fc3e6a ]

Using struct_size() to calculate the size of io_uring_buf_ring will sum
the size of the struct and of the bufs array. However, the struct's fields
are overlaid with the array making the calculated size larger than it
should be.

When registering a ring with N * PAGE_SIZE / sizeof(struct io_uring_buf)
entries, i.e. with fully filled pages, the calculated size will span one
more page than it should and io_uring will try to pin the following page.
Depending on how the application allocated the ring, it might succeed
using an unrelated page or fail returning EFAULT.

The size of the ring should be the product of ring_entries and the size
of io_uring_buf, i.e. the size of the bufs array only.

Fixes: c7fb19428d67 ("io_uring: add support for ring mapped supplied buffers")
Signed-off-by: Wojciech Lukowicz <wlukowicz01@gmail.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@suse.de>
Link: https://lore.kernel.org/r/20230218184141.70891-1-wlukowicz01@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: allow rtc_read_alarm without read_alarm callback

[ Upstream commit a783c962619271a8b905efad1d89adfec11ae0c8 ]

.read_alarm is not necessary to read the current alarm because it is
recorded in the aie_timer and so rtc_read_alarm() will never call
rtc_read_alarm_internal() which is the only function calling the callback.

Reported-by: Zhipeng Wang <zhipeng.wang_1@nxp.com>
Reported-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Fixes: 7ae41220ef58 ("rtc: introduce features bitfield")
Tested-by: Philippe Schenker <philippe.schenker@toradex.com>
Link: https://lore.kernel.org/r/20230214222754.582582-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: mpi3mr: Use number of bits to manage bitmap sizes

[ Upstream commit 339e61565f81a6534afdc18fd854b2e2628bf5db ]

To allocate bitmaps, the mpi3mr driver calculates sizes of bitmaps using
byte as unit. However, bitmap helper functions assume that bitmaps are
allocated using unsigned long as unit. This gap causes memory access beyond
the bitmap sizes and results in "BUG: KASAN: slab-out-of-bounds".  The BUG
was observed at firmware download to eHBA-9600. Call trace indicated that
the out-of-bounds access happened in find_first_zero_bit() called from
mpi3mr_send_event_ack() for miroc->evtack_cmds_bitmap.

To fix the BUG, do not use bytes to manage bitmap sizes. Instead, use
number of bits, and call bitmap helper functions which take number of bits
as arguments. For memory allocation, call bitmap_zalloc() instead of
kzalloc() and krealloc(). For memory free, call bitmap_free() instead of
kfree(). For zero clear, call bitmap_clear() instead of memset().

Remove three fields for bitmap byte sizes in struct scmd_priv which are no
longer required. Replace the field dev_handle_bitmap_sz with
dev_handle_bitmap_bits to keep number of bits of removepend_bitmap across
resize.

Link: https://lore.kernel.org/r/20230214005019.1897251-4-shinichiro.kawasaki@wdc.com
Fixes: c5758fc72b92 ("scsi: mpi3mr: Gracefully handle online FW update operation")
Fixes: e844adb1fbdc ("scsi: mpi3mr: Implement SCSI error handler hooks")
Fixes: c1af985d27da ("scsi: mpi3mr: Add Event acknowledgment logic")
Fixes: 824a156633df ("scsi: mpi3mr: Base driver code")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: mpi3mr: Fix an issue found by KASAN

[ Upstream commit ae7d45f5283d30274039b95d3e6d53d33c66e991 ]

Write only correct size (32 instead of 64 bytes).

Link: https://lore.kernel.org/r/20230213193752.6859-1-thenzl@redhat.com
Fixes: 42fc9fee116f ("scsi: mpi3mr: Add helper functions to manage device's port")
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: ipr: Work around fortify-string warning

[ Upstream commit ee4e7dfe4ffc9ca50c6875757bd119abfe22b5c5 ]

The ipr_log_vpd_compact() function triggers a fortified memcpy() warning
about a potential string overflow with all versions of clang:

In file included from drivers/scsi/ipr.c:43:
In file included from include/linux/string.h:254:
include/linux/fortify-string.h:520:4: error: call to '__write_overflow_field' declared with 'warning' attribute: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror,-Wattribute-warning]
                        __write_overflow_field(p_size_field, size);
                        ^
include/linux/fortify-string.h:520:4: error: call to '__write_overflow_field' declared with 'warning' attribute: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror,-Wattribute-warning]
2 errors generated.

I don't see anything actually wrong with the function, but this is the only
instance I can reproduce of the fortification going wrong in the kernel at
the moment, so the easiest solution may be to rewrite the function into
something that does not trigger the warning.

Instead of having a combined buffer for vendor/device/serial strings, use
three separate local variables and just truncate the whitespace
individually.

Link: https://lore.kernel.org/r/20230214132831.2118392-1-arnd@kernel.org
Cc: Kees Cook <keescook@chromium.org>
Fixes: 8cf093e275d0 ("[SCSI] ipr: Improved dual adapter errors")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

genirq/ipi: Fix NULL pointer deref in irq_data_get_affinity_mask()

[ Upstream commit feabecaff5902f896531dde90646ca5dfa9d4f7d ]

If ipi_send_{mask|single}() is called with an invalid interrupt number, all
the local variables there will be NULL. ipi_send_verify() which is invoked
from these functions does verify its 'data' parameter, resulting in a
kernel oops in irq_data_get_affinity_mask() as the passed NULL pointer gets
dereferenced.

Add a missing NULL pointer check in ipi_send_verify()...

Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.

Fixes: 3b8e29a82dd1 ("genirq: Implement ipi_send_mask/single()")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/b541232d-c2b6-1fe9-79b4-a7129459e4d0@omp.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: sun6i: Always export the internal oscillator

[ Upstream commit 344f4030f6c50a9db2d03021884c4bf36191b53a ]

On all variants of the hardware, the internal oscillator is one possible
parent for the AR100 clock. It needs to be exported so we can model that
relationship correctly in the devicetree.

Fixes: c56afc1844d6 ("rtc: sun6i: Expose internal oscillator through device tree")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221229215319.14145-1-samuel@sholland.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

spi: tegra210-quad: Fix iterator outside loop

[ Upstream commit 2449d436681d40bc63ec2c766fd51b632270d8a7 ]

Fix warn: iterator used outside loop: 'xfer'. 'xfer' variable contain
invalid value in few conditions. Complete transfer within DATA phase
in successful case and at the end for failed transfer.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link:https://lore.kernel.org/all/202210191211.46FkzKmv-lkp@intel.com/
Fixes: 8777dd9dff40 ("spi: tegra210-quad: Fix combined sequence")

Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/20230227200428.45832-1-kyarlagadda@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

vc_screen: modify vcs_size() handling in vcs_read()

[ Upstream commit 46d733d0efc79bc8430d63b57ab88011806d5180 ]

Restore the vcs_size() handling in vcs_read() to what
it had been in previous version.

Fixes: 226fae124b2d ("vc_screen: move load of struct vc_data pointer in vcs_read() to avoid UAF")
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tcp: tcp_check_req() can be called from process context

[ Upstream commit 580f98cc33a260bb8c6a39ae2921b29586b84fdf ]

This is a follow up of commit 0a375c822497 ("tcp: tcp_rtx_synack()
can be called from process context").

Frederick Lawler reported another "__this_cpu_add() in preemptible"
warning caused by the same reason.

In my former patch I took care of tcp_rtx_synack()
but forgot that tcp_check_req() also contained some SNMP updates.

Note that some parts of tcp_check_req() always run in BH context,
I added a comment to clarify this.

Fixes: 8336886f786f ("tcp: TCP Fast Open Server - support TFO listeners")
Link: https://lore.kernel.org/netdev/8cd33923-a21d-397c-e46b-2a068c287b03@cloudflare.com/T/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Frederick Lawler <fred@cloudflare.com>
Tested-by: Frederick Lawler <fred@cloudflare.com>
Link: https://lore.kernel.org/r/20230227083336.4153089-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: spear320-hmi: correct STMPE GPIO compatible

[ Upstream commit 33a0c1b850c8c85f400531dab3a0b022cdb164b1 ]

The compatible is st,stmpe-gpio.

Fixes: e2eb69183ec4 ("ARM: SPEAr320: DT: Add SPEAr 320 HMI board support")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20230225162237.40242-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: felix: fix internal MDIO controller resource length

[ Upstream commit 940af261321307cd1dd0fe8f9c34a6129f9d4bdc ]

The blamed commit did not properly convert the resource start/end format
into the DEFINE_RES_MEM_NAMED() start/length format, resulting in a
resource for vsc9959_imdio_res which is much longer than expected:

$ cat /proc/iomem
1f8000000-1f815ffff : pcie@1f0000000
  1f8140000-1f815ffff : 0000:00:00.5
    1f8148030-1f815006f : imdio

vs (correct)

$ cat /proc/iomem
1f8000000-1f815ffff : pcie@1f0000000
  1f8140000-1f815ffff : 0000:00:00.5
    1f8148030-1f814803f : imdio

Luckily it's not big enough to exceed the size of the parent resource
(pci_resource_end(pdev, VSC9959_IMDIO_PCI_BAR)), and it doesn't overlap
with anything else that the Linux driver uses currently, so the larger
than expected size isn't a practical problem that I can see. Although it
is clearly wrong in the /proc/iomem output.

Fixes: 044d447a801f ("net: dsa: felix: use DEFINE_RES_MEM_NAMED for resources")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: seville: ignore mscc-miim read errors from Lynx PCS

[ Upstream commit 0322ef49c1ac6f0e2ef37b146c0bf8440873072c ]

During the refactoring in the commit below, vsc9953_mdio_read() was
replaced with mscc_miim_read(), which has one extra step: it checks for
the MSCC_MIIM_DATA_ERROR bits before returning the result.

On T1040RDB, there are 8 QSGMII PCSes belonging to the switch, and they
are organized in 2 groups. First group responds to MDIO addresses 4-7
because QSGMIIACR1[MDEV_PORT] is 1, and the second group responds to
MDIO addresses 8-11 because QSGMIIBCR1[MDEV_PORT] is 2. I have double
checked that these values are correctly set in the SERDES, as well as
PCCR1[QSGMA_CFG] and PCCR1[QSGMB_CFG] are both 0b01.

mscc_miim_read: phyad 8 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 8 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 8 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 8 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 9 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 9 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 9 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 9 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 10 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 10 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 10 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 10 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 11 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 11 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 11 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 11 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 4 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 4 reg 0x5 MIIM_DATA 0x3da01, ERROR
mscc_miim_read: phyad 5 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 5 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 5 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 5 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 6 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 6 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 6 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 6 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 7 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 7 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 7 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 7 reg 0x5 MIIM_DATA 0x35801, ERROR

As can be seen, the data in MIIM_DATA is still valid despite having the
MSCC_MIIM_DATA_ERROR bits set. The driver as introduced in commit
84705fc16552 ("net: dsa: felix: introduce support for Seville VSC9953
switch") was ignoring these bits, perhaps deliberately (although
unbeknownst to me).

This is an old IP and the hardware team cannot seem to be able to help
me track down a plausible reason for these failures. I'll keep
investigating, but in the meantime, this is a direct regression which
must be restored to a working state.

The only thing I can do is keep ignoring the errors as before.

Fixes: b99658452355 ("net: dsa: ocelot: felix: utilize shared mscc-miim driver for indirect MDIO access")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/sched: act_sample: fix action bind logic

[ Upstream commit 4a20056a49a1854966562241922f68197f950539 ]

The TC architecture allows filters and actions to be created independently.
In filters the user can reference action objects using:
tc action add action sample ... index 1
tc filter add ... action pedit index 1

In the current code for act_sample this is broken as it checks netlink
attributes for create/update before actually checking if we are binding to an
existing action.

tdc results:
1..29
ok 1 9784 - Add valid sample action with mandatory arguments
ok 2 5c91 - Add valid sample action with mandatory arguments and continue control action
ok 3 334b - Add valid sample action with mandatory arguments and drop control action
ok 4 da69 - Add valid sample action with mandatory arguments and reclassify control action
ok 5 13ce - Add valid sample action with mandatory arguments and pipe control action
ok 6 1886 - Add valid sample action with mandatory arguments and jump control action
ok 7 7571 - Add sample action with invalid rate
ok 8 b6d4 - Add sample action with mandatory arguments and invalid control action
ok 9 a874 - Add invalid sample action without mandatory arguments
ok 10 ac01 - Add invalid sample action without mandatory argument rate
ok 11 4203 - Add invalid sample action without mandatory argument group
ok 12 14a7 - Add invalid sample action without mandatory argument group
ok 13 8f2e - Add valid sample action with trunc argument
ok 14 45f8 - Add sample action with maximum rate argument
ok 15 ad0c - Add sample action with maximum trunc argument
ok 16 83a9 - Add sample action with maximum group argument
ok 17 ed27 - Add sample action with invalid rate argument
ok 18 2eae - Add sample action with invalid group argument
ok 19 6ff3 - Add sample action with invalid trunc size
ok 20 2b2a - Add sample action with invalid index
ok 21 dee2 - Add sample action with maximum allowed index
ok 22 560e - Add sample action with cookie
ok 23 704a - Replace existing sample action with new rate argument
ok 24 60eb - Replace existing sample action with new group argument
ok 25 2cce - Replace existing sample action with new trunc argument
ok 26 59d1 - Replace existing sample action with new control argument
ok 27 0a6e - Replace sample action with invalid goto chain control
ok 28 3872 - Delete sample action with valid index
ok 29 a394 - Delete sample action with invalid index

Fixes: 5c5670fae430 ("net/sched: Introduce sample tc action")
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/sched: act_mpls: fix action bind logic

[ Upstream commit e88d78a773cb5242e933930c8855bf4b2e8c2397 ]

The TC architecture allows filters and actions to be created independently.
In filters the user can reference action objects using:
tc action add action mpls ... index 1
tc filter add ... action mpls index 1

In the current code for act_mpls this is broken as it checks netlink
attributes for create/update before actually checking if we are binding to an
existing action.

tdc results:
1..53
ok 1 a933 - Add MPLS dec_ttl action with pipe opcode
ok 2 08d1 - Add mpls dec_ttl action with pass opcode
ok 3 d786 - Add mpls dec_ttl action with drop opcode
ok 4 f334 - Add mpls dec_ttl action with reclassify opcode
ok 5 29bd - Add mpls dec_ttl action with continue opcode
ok 6 48df - Add mpls dec_ttl action with jump opcode
ok 7 62eb - Add mpls dec_ttl action with trap opcode
ok 8 09d2 - Add mpls dec_ttl action with opcode and cookie
ok 9 c170 - Add mpls dec_ttl action with opcode and cookie of max length
ok 10 9118 - Add mpls dec_ttl action with invalid opcode
ok 11 6ce1 - Add mpls dec_ttl action with label (invalid)
ok 12 352f - Add mpls dec_ttl action with tc (invalid)
ok 13 fa1c - Add mpls dec_ttl action with ttl (invalid)
ok 14 6b79 - Add mpls dec_ttl action with bos (invalid)
ok 15 d4c4 - Add mpls pop action with ip proto
ok 16 91fb - Add mpls pop action with ip proto and cookie
ok 17 92fe - Add mpls pop action with mpls proto
ok 18 7e23 - Add mpls pop action with no protocol (invalid)
ok 19 6182 - Add mpls pop action with label (invalid)
ok 20 6475 - Add mpls pop action with tc (invalid)
ok 21 067b - Add mpls pop action with ttl (invalid)
ok 22 7316 - Add mpls pop action with bos (invalid)
ok 23 38cc - Add mpls push action with label
ok 24 c281 - Add mpls push action with mpls_mc protocol
ok 25 5db4 - Add mpls push action with label, tc and ttl
ok 26 7c34 - Add mpls push action with label, tc ttl and cookie of max length
ok 27 16eb - Add mpls push action with label and bos
ok 28 d69d - Add mpls push action with no label (invalid)
ok 29 e8e4 - Add mpls push action with ipv4 protocol (invalid)
ok 30 ecd0 - Add mpls push action with out of range label (invalid)
ok 31 d303 - Add mpls push action with out of range tc (invalid)
ok 32 fd6e - Add mpls push action with ttl of 0 (invalid)
ok 33 19e9 - Add mpls mod action with mpls label
ok 34 1fde - Add mpls mod action with max mpls label
ok 35 0c50 - Add mpls mod action with mpls label exceeding max (invalid)
ok 36 10b6 - Add mpls mod action with mpls label of MPLS_LABEL_IMPLNULL (invalid)
ok 37 57c9 - Add mpls mod action with mpls min tc
ok 38 6872 - Add mpls mod action with mpls max tc
ok 39 a70a - Add mpls mod action with mpls tc exceeding max (invalid)
ok 40 6ed5 - Add mpls mod action with mpls ttl
ok 41 77c1 - Add mpls mod action with mpls ttl and cookie
ok 42 b80f - Add mpls mod action with mpls max ttl
ok 43 8864 - Add mpls mod action with mpls min ttl
ok 44 6c06 - Add mpls mod action with mpls ttl of 0 (invalid)
ok 45 b5d8 - Add mpls mod action with mpls ttl exceeding max (invalid)
ok 46 451f - Add mpls mod action with mpls max bos
ok 47 a1ed - Add mpls mod action with mpls min bos
ok 48 3dcf - Add mpls mod action with mpls bos exceeding max (invalid)
ok 49 db7c - Add mpls mod action with protocol (invalid)
ok 50 b070 - Replace existing mpls push action with new ID
ok 51 95a9 - Replace existing mpls push action with new label, tc, ttl and cookie
ok 52 6cce - Delete mpls pop action
ok 53 d138 - Flush mpls actions

Fixes: 2a2ea50870ba ("net: sched: add mpls manipulation actions to TC")
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/sched: act_pedit: fix action bind logic

[ Upstream commit e9e42292ea76a8358b0c02ffd530d78e133a1b73 ]

The TC architecture allows filters and actions to be created independently.
In filters the user can reference action objects using:
tc action add action pedit ... index 1
tc filter add ... action pedit index 1

In the current code for act_pedit this is broken as it checks netlink
attributes for create/update before actually checking if we are binding to an
existing action.

tdc results:
1..69
ok 1 319a - Add pedit action that mangles IP TTL
ok 2 7e67 - Replace pedit action with invalid goto chain
ok 3 377e - Add pedit action with RAW_OP offset u32
ok 4 a0ca - Add pedit action with RAW_OP offset u32 (INVALID)
ok 5 dd8a - Add pedit action with RAW_OP offset u16 u16
ok 6 53db - Add pedit action with RAW_OP offset u16 (INVALID)
ok 7 5c7e - Add pedit action with RAW_OP offset u8 add value
ok 8 2893 - Add pedit action with RAW_OP offset u8 quad
ok 9 3a07 - Add pedit action with RAW_OP offset u8-u16-u8
ok 10 ab0f - Add pedit action with RAW_OP offset u16-u8-u8
ok 11 9d12 - Add pedit action with RAW_OP offset u32 set u16 clear u8 invert
ok 12 ebfa - Add pedit action with RAW_OP offset overflow u32 (INVALID)
ok 13 f512 - Add pedit action with RAW_OP offset u16 at offmask shift set
ok 14 c2cb - Add pedit action with RAW_OP offset u32 retain value
ok 15 1762 - Add pedit action with RAW_OP offset u8 clear value
ok 16 bcee - Add pedit action with RAW_OP offset u8 retain value
ok 17 e89f - Add pedit action with RAW_OP offset u16 retain value
ok 18 c282 - Add pedit action with RAW_OP offset u32 clear value
ok 19 c422 - Add pedit action with RAW_OP offset u16 invert value
ok 20 d3d3 - Add pedit action with RAW_OP offset u32 invert value
ok 21 57e5 - Add pedit action with RAW_OP offset u8 preserve value
ok 22 99e0 - Add pedit action with RAW_OP offset u16 preserve value
ok 23 1892 - Add pedit action with RAW_OP offset u32 preserve value
ok 24 4b60 - Add pedit action with RAW_OP negative offset u16/u32 set value
ok 25 a5a7 - Add pedit action with LAYERED_OP eth set src
ok 26 86d4 - Add pedit action with LAYERED_OP eth set src & dst
ok 27 f8a9 - Add pedit action with LAYERED_OP eth set dst
ok 28 c715 - Add pedit action with LAYERED_OP eth set src (INVALID)
ok 29 8131 - Add pedit action with LAYERED_OP eth set dst (INVALID)
ok 30 ba22 - Add pedit action with LAYERED_OP eth type set/clear sequence
ok 31 dec4 - Add pedit action with LAYERED_OP eth set type (INVALID)
ok 32 ab06 - Add pedit action with LAYERED_OP eth add type
ok 33 918d - Add pedit action with LAYERED_OP eth invert src
ok 34 a8d4 - Add pedit action with LAYERED_OP eth invert dst
ok 35 ee13 - Add pedit action with LAYERED_OP eth invert type
ok 36 7588 - Add pedit action with LAYERED_OP ip set src
ok 37 0fa7 - Add pedit action with LAYERED_OP ip set dst
ok 38 5810 - Add pedit action with LAYERED_OP ip set src & dst
ok 39 1092 - Add pedit action with LAYERED_OP ip set ihl & dsfield
ok 40 02d8 - Add pedit action with LAYERED_OP ip set ttl & protocol
ok 41 3e2d - Add pedit action with LAYERED_OP ip set ttl (INVALID)
ok 42 31ae - Add pedit action with LAYERED_OP ip ttl clear/set
ok 43 486f - Add pedit action with LAYERED_OP ip set duplicate fields
ok 44 e790 - Add pedit action with LAYERED_OP ip set ce, df, mf, firstfrag, nofrag fields
ok 45 cc8a - Add pedit action with LAYERED_OP ip set tos
ok 46 7a17 - Add pedit action with LAYERED_OP ip set precedence
ok 47 c3b6 - Add pedit action with LAYERED_OP ip add tos
ok 48 43d3 - Add pedit action with LAYERED_OP ip add precedence
ok 49 438e - Add pedit action with LAYERED_OP ip clear tos
ok 50 6b1b - Add pedit action with LAYERED_OP ip clear precedence
ok 51 824a - Add pedit action with LAYERED_OP ip invert tos
ok 52 106f - Add pedit action with LAYERED_OP ip invert precedence
ok 53 6829 - Add pedit action with LAYERED_OP beyond ip set dport & sport
ok 54 afd8 - Add pedit action with LAYERED_OP beyond ip set icmp_type & icmp_code
ok 55 3143 - Add pedit action with LAYERED_OP beyond ip set dport (INVALID)
ok 56 815c - Add pedit action with LAYERED_OP ip6 set src
ok 57 4dae - Add pedit action with LAYERED_OP ip6 set dst
ok 58 fc1f - Add pedit action with LAYERED_OP ip6 set src & dst
ok 59 6d34 - Add pedit action with LAYERED_OP ip6 dst retain value (INVALID)
ok 60 94bb - Add pedit action with LAYERED_OP ip6 traffic_class
ok 61 6f5e - Add pedit action with LAYERED_OP ip6 flow_lbl
ok 62 6795 - Add pedit action with LAYERED_OP ip6 set payload_len, nexthdr, hoplimit
ok 63 1442 - Add pedit action with LAYERED_OP tcp set dport & sport
ok 64 b7ac - Add pedit action with LAYERED_OP tcp sport set (INVALID)
ok 65 cfcc - Add pedit action with LAYERED_OP tcp flags set
ok 66 3bc4 - Add pedit action with LAYERED_OP tcp set dport, sport & flags fields
ok 67 f1c8 - Add pedit action with LAYERED_OP udp set dport & sport
ok 68 d784 - Add pedit action with mixed RAW/LAYERED_OP #1
ok 69 70ca - Add pedit action with mixed RAW/LAYERED_OP #2

Fixes: 71d0ed7079df ("net/act_pedit: Support using offset relative to the conventional network headers")
Fixes: f67169fef8db ("net/sched: act_pedit: fix WARN() in the traffic path")
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/sched: transition act_pedit to rcu and percpu stats

[ Upstream commit 52cf89f78c01bf39973f3e70d366921d70faff7a ]

The software pedit action didn't get the same love as some of the
other actions and it's still using spinlocks and shared stats in the
datapath.
Transition the action to rcu and percpu stats as this improves the
action's performance dramatically on multiple cpu deployments.

Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: e9e42292ea76 ("net/sched: act_pedit: fix action bind logic")
Signed-off-by: Sasha Levin <sashal@kernel.org>

nfc: fix memory leak of se_io context in nfc_genl_se_io

[ Upstream commit 25ff6f8a5a3b8dc48e8abda6f013e8cc4b14ffea ]

The callback context for sending/receiving APDUs to/from the selected
secure element is allocated inside nfc_genl_se_io and supposed to be
eventually freed in se_io_cb callback function. However, there are several
error paths where the bwi_timer is not charged to call se_io_cb later, and
the cb_context is leaked.

The patch proposes to free the cb_context explicitly on those error paths.

At the moment we can't simply check 'dev->ops->se_io()' return value as it
may be negative in both cases: when the timer was charged and was not.

Fixes: 5ce3f32b5264 ("NFC: netlink: SE API implementation")
Reported-by: syzbot+df64c0a2e8d68e78a4fa@syzkaller.appspotmail.com
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ext4: fix incorrect options show of original mount_opt and extend mount_opt2

[ Upstream commit e3645d72f8865ffe36f9dc811540d40aa3c848d3 ]

Current _ext4_show_options() do not distinguish MOPT_2 flag, so it mixed
extend sbi->s_mount_opt2 options with sbi->s_mount_opt, it could lead to
show incorrect options, e.g. show fc_debug_force if we mount with
errors=continue mode and miss it if we set.

  $ mkfs.ext4 /dev/pmem0
  $ mount -o errors=remount-ro /dev/pmem0 /mnt
  $ cat /proc/fs/ext4/pmem0/options | grep fc_debug_force
    #empty
  $ mount -o remount,errors=continue /mnt
  $ cat /proc/fs/ext4/pmem0/options | grep fc_debug_force
    fc_debug_force
  $ mount -o remount,errors=remount-ro,fc_debug_force /mnt
  $ cat /proc/fs/ext4/pmem0/options | grep fc_debug_force
    #empty

Fixes: 995a3ed67fc8 ("ext4: add fast_commit feature and handling for extended mount options")
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230129034939.3702550-1-yi.zhang@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5: Geneve, Fix handling of Geneve object id as error code

[ Upstream commit d28a06d7dbedc598a06bd1e53a28125f87ca5d0c ]

On success, mlx5_geneve_tlv_option_create returns non negative
Geneve object id. In case the object id is positive value the
caller functions will handle it as an error (non zero) and
will fail to offload the Geneve rule.

Fix this by changing caller function ,mlx5_geneve_tlv_option_add,
to return 0 in case valid non negative object id was provided.

Fixes: 0ccc171ea6a2 ("net/mlx5: Geneve, Manage Geneve TLV options")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5e: Verify flow_source cap before using it

[ Upstream commit 1bf8b0dae8dde6f02520a5ea34fdaa3b39342e69 ]

When adding send to vport rule verify flow_source matching is
supported by checking the flow_source cap.

Fixes: d04442540372 ("net/mlx5: E-Switch, set flow source for send to uplink rule")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5: ECPF, wait for VF pages only after disabling host PFs

[ Upstream commit e1ed30c8c09abc85a01c897845bdbd08c0333353 ]

Currently,  during the early stages of their unloading, particularly
during SRIOV disablement, PFs/ECPFs wait on the release of all of
their VFs memory pages. Furthermore, ECPFs are considered the page
supplier for host VFs, hence the host VFs memory pages are freed only
during ECPF cleanup when host interfaces get disabled.

Thus, disabling SRIOV early in unload timeline causes the DPU ECPF
to stall on driver unload while waiting on the release of host VF pages
that won't be freed before host interfaces get disabled later on.

Therefore, for ECPFs, wait on the release of VFs pages only after the
disablement of host PFs during ECPF cleanup flow. Then, host PFs and VFs
are disabled and their memory shall be freed accordingly.

Fixes: 143a41d7623d ("net/mlx5: Disable SRIOV before PF removal")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mlx5: fix possible ptp queue fifo use-after-free

[ Upstream commit 3a50cf1e8e5157b82268eee7e330dbe5736a0948 ]

Fifo indexes are not checked during pop operations and it leads to
potential use-after-free when poping from empty queue. Such case was
possible during re-sync action. WARN_ON_ONCE covers future cases.

There were out-of-order cqe spotted which lead to drain of the queue and
use-after-free because of lack of fifo pointers check. Special check and
counter are added to avoid resync operation if SKB could not exist in the
fifo because of OOO cqe (skb_id must be between consumer and producer
index).

Fixes: 58a518948f60 ("net/mlx5e: Add resiliency for PTP TX port timestamp")
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mlx5: fix skb leak while fifo resync and push

[ Upstream commit e435941b1da1a0be4ff8a7ae425774c76a5ac514 ]

During ptp resync operation SKBs were poped from the fifo but were never
freed neither by napi_consume nor by dev_kfree_skb_any. Add call to
napi_consume_skb to properly free SKBs.

Another leak was happening because mlx5e_skb_fifo_has_room() had an error
in the check. Comparing free running counters works well unless C promotes
the types to something wider than the counter. In this case counters are
u16 but the result of the substraction is promouted to int and it causes
wrong result (negative value) of the check when producer have already
overlapped but consumer haven't yet. Explicit cast to u16 fixes the issue.

Fixes: 58a518948f60 ("net/mlx5e: Add resiliency for PTP TX port timestamp")
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

spi: tegra210-quad: Fix validate combined sequence

[ Upstream commit 047ee71ae4f412d8819e39e4b08c588fa299cfc2 ]

Check for non dma transfers that do not fit in FIFO has issue and skips
combined sequence for Tegra234 & Tegra241 which does not have GPCDMA.

Fixes: 1b8342cc4a38 ("spi: tegra210-quad: combined sequence mode")

Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/20230224164034.56933-1-kyarlagadda@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

9p/rdma: unmap receive dma buffer in rdma_request()/post_recv()

[ Upstream commit 74a25e6e916cb57dab4267a96fbe8864ed21abdb ]

When down_interruptible() or ib_post_send() failed in rdma_request(),
receive dma buffer is not unmapped. Add unmap action to error path.
Also if ib_post_recv() failed in post_recv(), dma buffer is not unmapped.
Add unmap action to error path.

Link: https://lkml.kernel.org/r/20230104020424.611926-1-shaozhengchao@huawei.com
Fixes: fc79d4b104f0 ("9p: rdma: RDMA Transport Support for 9P")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: Eric Van Hensbergen <ericvh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

9p/xen: fix connection sequence

[ Upstream commit c15fe55d14b3b4ded5af2a3260877460a6ffb8ad ]

Today the connection sequence of the Xen 9pfs frontend doesn't match
the documented sequence. It can work reliably only for a PV 9pfs device
having been added at boot time already, as the frontend is not waiting
for the backend to have set its state to "XenbusStateInitWait" before
reading the backend properties from Xenstore.

Fix that by following the documented sequence [1] (the documentation
has a bug, so the reference is for the patch fixing that).

[1]: https://lore.kernel.org/xen-devel/20230130090937.31623-1-jgross@suse.com/T/#u

Link: https://lkml.kernel.org/r/20230130113036.7087-3-jgross@suse.com
Fixes: 868eb122739a ("xen/9pfs: introduce Xen 9pfs transport driver")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: Eric Van Hensbergen <ericvh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

9p/xen: fix version parsing

[ Upstream commit f1956f4ec15195ec60976d9b5625326285ab102e ]

When connecting the Xen 9pfs frontend to the backend, the "versions"
Xenstore entry written by the backend is parsed in a wrong way.

The "versions" entry is defined to contain the versions supported by
the backend separated by commas (e.g. "1,2"). Today only version "1"
is defined. Unfortunately the frontend doesn't look for "1" being
listed in the entry, but it is expecting the entry to have the value
"1".

This will result in failure as soon as the backend will support e.g.
versions "1" and "2".

Fix that by scanning the entry correctly.

Link: https://lkml.kernel.org/r/20230130113036.7087-2-jgross@suse.com
Fixes: 71ebd71921e4 ("xen/9pfs: connect to the backend")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: Eric Van Hensbergen <ericvh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>