Olof Johansson [Thu, 25 Jul 2013 00:06:47 +0000 (17:06 -0700)]
Merge tag 'samsung-fixes-1' of git://git./linux/kernel/git/kgene/linux-samsung into fixes
From Kukjin Kim:
Samsung fixes for v3.11
- fix kernel booting on exynos5440
skip pm which is not supported
update regarding LPAE features
- fix s3c2440 uart with adding clkdev entries
- fix compilatioin for Samsung SoCs with selecting pm
- update ARCH_NR_GPIO to support exynos4412 has more gpios
* tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Update CONFIG_ARCH_NR_GPIO for Exynos
ARM: EXYNOS: Fix low level debug support
ARM: SAMSUNG: Save/restore only selected uart's registers
ARM: SAMSUNG: Add SAMSUNG_PM config option to select pm
ARM: S3C24XX: Add missing clkdev entries for s3c2440 UART
ARM: EXYNOS: Enable 64-bit DMA for EXYNOS5440 if LPAE is enabled
ARM: EXYNOS: change the PHYSMEM_BITS and SECTION_SIZE
ARM: EXYNOS: skip pm support on exynos5440
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Wed, 24 Jul 2013 23:55:23 +0000 (16:55 -0700)]
ARM: omap5: Only select errata 798181 if SMP
Avoids the following warning when SMP is off:
warning: (ARCH_KEYSTONE && SOC_OMAP5) selects ARM_ERRATA_798181 which
has unmet direct dependencies (CPU_V7 && SMP)
Reported-by: Emilio López <emilio@elopez.com.ar>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Sachin Kamat [Wed, 24 Jul 2013 09:55:27 +0000 (18:55 +0900)]
ARM: EXYNOS: Update CONFIG_ARCH_NR_GPIO for Exynos
With the recent cleanup in Exynos platform code notably commits
17859bec ("ARM: EXYNOS: Do not select legacy Kconfig symbols any
more") and
b9222210 ("ARM: EXYNOS: Remove mach/gpio.h"), the definition
of ARCH_NR_GPIOS got removed. This started causing problems on SoCs like
Exynos4412 which have more than the default number of GPIOs. Thus define
this number in KConfig file which takes care of current SoC requirements
and provides scope for GPIO expanders. Without this patch we get the
following errors during boot:
gpiochip_add: gpios 251..258 (gpv0) failed to register
samsung-pinctrl
106e0000.pinctrl: failed to register gpio_chip gpv0, error code: -22
samsung-pinctrl: probe of
106e0000.pinctrl failed with error -22
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Yadwinder Singh Brar [Wed, 24 Jul 2013 08:05:32 +0000 (17:05 +0900)]
ARM: EXYNOS: Fix low level debug support
Presently, using exynos_defconfig with CONFIG_DEBUG_LL and CONFIG_EARLY_PRIN
on, kernel is not booting, we are getting following:
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] kernel BUG at mm/vmalloc.c:1134!
[ 0.000000] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 3.11.0-rc1 #633
[ 0.000000] task:
c052ec48 ti:
c0524000 task.ti:
c0524000
[ 0.000000] PC is at vm_area_add_early+0x54/0x94
[ 0.000000] LR is at add_static_vm_early+0xc/0x60
Its because exynos[4/5]_map_io() function ioremaps a single 512KB memory
size for all the four uart ports which envelopes the mapping created by
debug_ll_io_init(), called earlier in exynos_init_io().
This patch removes iodesc entries for UART controller for all Samsung SoC's,
since now the Samsung uart driver does a ioremap during probe and any needed
iomapping for earlyprintk will be handled by debug_ll_io_init().
Tested on smdk4412 and smdk5250.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Yadwinder Singh Brar [Wed, 24 Jul 2013 08:05:07 +0000 (17:05 +0900)]
ARM: SAMSUNG: Save/restore only selected uart's registers
Basically this code gets executed only during debugging i.e when
DEBUG_LL & SAMSUNG_PM_DEBUG is on, so required only for UART used
for debugging. Since we are removing static iodesc entries for UARTs,
so now only the selected (CONFIG_DEBUG_S3C_UART) UART will be
ioremapped by the debug_ll_io_init() for DEBUG_LL, so save/restore
uart registers only for selected uart.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Amit Daniel Kachhap [Wed, 24 Jul 2013 05:06:13 +0000 (14:06 +0900)]
ARM: SAMSUNG: Add SAMSUNG_PM config option to select pm
This patch enables the selection of samsung pm related stuffs
when SAMSUNG_PM config is enabled and not just when generic PM
config is enabled. Power management for s3c64XX and s3c24XX
is enabled by default and for other platform depends on S5P_PM.
This patch also fixes the following compilation error's when compiling
a platform like exynos5440 which does not select pm stuffs.
arch/arm/mach-exynos/built-in.o: In function '__virt_to_phys':
linux/arch/arm/include/asm/memory.h:175: undefined reference to 's3c_cpu_resume'
linux/arch/arm/include/asm/memory.h:175: undefined reference to 's3c_cpu_resume'
linux/arch/arm/include/asm/memory.h:175: undefined reference to 's3c_cpu_resume'
linux/arch/arm/include/asm/memory.h:175: undefined reference to 's3c_cpu_resume'
arch/arm/mach-exynos/built-in.o: In function 'exynos5_init_irq':
linux/arch/arm/mach-exynos/common.c:492: undefined reference to 's3c_irq_wake'
linux/arch/arm/mach-exynos/common.c:492: undefined reference to 's3c_irq_wake'
arch/arm/mach-exynos/built-in.o: In function 'exynos4_init_irq':
linux/arch/arm/mach-exynos/common.c:476: undefined reference to 's3c_irq_wake'
linux/arch/arm/mach-exynos/common.c:476: undefined reference to 's3c_irq_wake'
arch/arm/plat-samsung/built-in.o: In function 's3c_irqext_wake':
linux/arch/arm/plat-samsung/pm.c:144: undefined reference to 's3c_irqwake_eintallow'
linux/arch/arm/plat-samsung/pm.c:144: undefined reference to 's3c_irqwake_eintallow'
arch/arm/plat-samsung/built-in.o: In function 's3c_pm_enter':
linux/arch/arm/plat-samsung/pm.c:263: undefined reference to 's3c_irqwake_intallow'
linux/arch/arm/plat-samsung/pm.c:263: undefined reference to 's3c_irqwake_intallow'
linux/arch/arm/plat-samsung/pm.c:264: undefined reference to 's3c_irqwake_eintallow'
linux/arch/arm/plat-samsung/pm.c:264: undefined reference to 's3c_irqwake_eintallow'
linux/arch/arm/plat-samsung/pm.c:275: undefined reference to 's3c_pm_save_core'
linux/arch/arm/plat-samsung/pm.c:279: undefined reference to 's3c_pm_configure_extint'
linux/arch/arm/plat-samsung/pm.c:310: undefined reference to 's3c_pm_restore_core'
make: *** [vmlinux] Error 1
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Sylwester Nawrocki [Wed, 24 Jul 2013 04:23:51 +0000 (13:23 +0900)]
ARM: S3C24XX: Add missing clkdev entries for s3c2440 UART
This patch restores serial port operation which has been broken since
commit
60e93575476f ("serial: samsung: enable clock before clearing
pending interrupts during init")
That commit only uncovered the real issue which was missing clkdev
entries for the "uart" clocks on S3C2440. It went unnoticed so far
because return value of clk API calls were not being checked at all
in the samsung serial port driver.
This patch should be backported to at least 3.10 stable kernel, since
the serial port has not been working on s3c2440 since 3.10-rc5.
Cc: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
[on S3C2440 SoC based Mini2440 board]
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Juergen Beisert <jbe@pengutronix.de>
Cc: <stable@vger.kernel.org> [3.10]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fabio Estevam [Tue, 23 Jul 2013 17:02:06 +0000 (14:02 -0300)]
ARM: multi_v7_defconfig: Select USB chipidea driver
CONFIG_USB_EHCI_MXC selects the old i.mx USB driver, which does not support
device tree.
Select the USB chipidea driver instead, so that USB can be functional on i.mx.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Arnd Bergmann [Fri, 5 Jul 2013 15:51:20 +0000 (17:51 +0200)]
ARM: pxa: propagate errors from regulator_enable() to pxamci
The em_x270_mci_setpower() and em_x270_usb_hub_init() functions
call regulator_enable(), which may return an error that must
be checked.
This changes the em_x270_usb_hub_init() function to bail out
if it fails, and changes the pxamci_platform_data->setpower
callback so that the a failed em_x270_mci_setpower call
can be propagated by the pxamci driver into the mmc core.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Chris Ball <cjb@laptop.org>
[olof: fixed order of regulator_enable() and test in em_x270_usb_hub_init]
Signed-off-by: Olof Johansson <olof@lixom.net>
Vincent Stehlé [Thu, 27 Jun 2013 12:42:41 +0000 (14:42 +0200)]
ARM: zynq: fix compilation warning
Fix the following compilation warning:
arch/arm/mach-zynq/common.c:110:2: warning: initialization from incompatible pointer type [enabled by default]
arch/arm/mach-zynq/common.c:110:2: warning: (near initialization for ‘__mach_desc_XILINX_EP107.restart’) [enabled by default]
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: trivial@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Vincent Stehlé [Thu, 27 Jun 2013 12:49:27 +0000 (14:49 +0200)]
ARM: keystone: fix compilation warning
Fix the following compilation warning:
arch/arm/mach-keystone/keystone.c:74:2: warning: initialization from incompatible pointer type [enabled by default]
arch/arm/mach-keystone/keystone.c:74:2: warning: (near initialization for ‘__mach_desc_KEYSTONE.restart’) [enabled by default]
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: trivial@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Rob Herring [Sun, 21 Jul 2013 19:53:37 +0000 (14:53 -0500)]
ARM: highbank: Only touch common coherency control register fields
Midway adds new register fields to the coherency control registers, so
writing absolute values will break on Midway. Change the register
accesses to only modify the necessary and common fields in order to
support both Midway and Highbank.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 23 Jul 2013 03:02:38 +0000 (20:02 -0700)]
Merge tag 'nomadik-defconfig-for-arm-soc' of git://git./linux/kernel/git/linusw/linux-nomadik into fixes
From Linus Walleij:
This updates the Nomadik defconfig post-v3.11-rc1:
- Update the baseline so we need not rely on make
oldconfig so much
- MMC defconfig updates
- Activate NO_HZ_IDLE and HRTIMERS
* tag 'nomadik-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: configure for NO_HZ and HRTIMERS
ARM: nomadik: update defconfig base
ARM: nomadik: Update MMC defconfigs
Signed-off-by: Olof Johansson <olof@lixom.net>
Mike Frysinger [Fri, 28 Jun 2013 02:42:36 +0000 (22:42 -0400)]
ARM: footbridge: fix overlapping PCI mappings
Commit
8ef6e6201b26cb9fde79c1baa08145af6aca2815 (ARM: footbridge: use
fixed PCI i/o mapping) broke booting on my netwinder. Before that,
everything boots fine. Since then, it crashes on boot.
With earlyprintk, I see it BUG-ing like so:
kernel BUG at lib/ioremap.c:27!
Internal error: Oops - BUG: 0 [#1] ARM
...
[<
c0139b54>] (ioremap_page_range+0x128/0x154) from [<
c02e6a6c>] (dc21285_setup+0xd0/0x114)
[<
c02e6a6c>] (dc21285_setup+0xd0/0x114) from [<
c02e4874>] (pci_common_init+0xa0/0x298)
[<
c02e4874>] (pci_common_init+0xa0/0x298) from [<
c02e793c>] (netwinder_pci_init+0xc/0x18)
[<
c02e793c>] (netwinder_pci_init+0xc/0x18) from [<
c02e27d0>] (do_one_initcall+0xb4/0x180)
...
Russell points out it's because of overlapping PCI mappings that was
added with the aforementioned commit. Rob thought the code would re-use
the static mapping, but that turns out to not be the case and instead
hits the BUG further down.
After deleting this hunk as suggested by Russel, the system boots up fine
again and all my PCI devices work (IDE, ethernet, the
DC21285).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: stable@vger.kernel.org # v3.5+
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 23 Jul 2013 02:58:02 +0000 (19:58 -0700)]
Merge tag 'imx-fixes-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo, imx fixes for 3.11:
- A few device tree source fixes regarding pinctrl, clock, and pwm
backlight.
- Fixes imx28 and imx51 audio driver failure caused by sgtl5000 codec
driver change by supplying the correct clock for codec.
- imx6q emi_sel clock muxing and imx6q-iomuxc-gpr macro fixes
* tag 'imx-fixes-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx51-babbage: Pass a real clock to the codec
ARM i.MX53: mba53: Fix PWM backlight DT node
ARM: imx: fix vf610 enet module clock selection
ARM: mxs: saif0 is the clock provider to sgtl5000
ARM: i.MX6Q: correct emi_sel clock muxing
ARM i.MX6Q: Fix IOMUXC GPR1 defines for ENET_CLK_SEL and IPU1/2_MUX
ARM: i.MX27: Typo fix
ARM: imx27: Fix documentation for SPLL clock
ARM i.MX53: Fix UART pad configuration
Olof Johansson [Tue, 23 Jul 2013 02:53:29 +0000 (19:53 -0700)]
Merge tag 'omap-for-v3.11/fixes-against-rc1' of git://git./linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Omap fixes mostly to deal with the dropping of platform data for omap4,
and to make v7_defconfig bootable on omap4 SDP with nfsroot.
* tag 'omap-for-v3.11/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Provide alias to USB PHY clock
ARM: dts: Add missing vmmc2 regulator for twl
ARM: multi_v7: Enabled omap4430 sdp nfsroot
Olof Johansson [Tue, 23 Jul 2013 02:50:11 +0000 (19:50 -0700)]
Merge tag 'davinci-fixes-for-v3.11-rc2' of git://git./linux/kernel/git/nsekhar/linux-davinci into fixes
From Sekhar Nori:
DaVinci fixes for v3.11-rc2
The pull request includes fixes for sparse warnings, defconfig changes to
enable DMA usage on peripherals and removal of a duplicated include file.
* tag 'davinci-fixes-for-v3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: defconfig: enable EDMA driver
ARM: davinci: make file local variables static
ARM: edma: remove duplicated include from edma.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Guennadi Liakhovetski [Wed, 10 Jul 2013 02:09:12 +0000 (11:09 +0900)]
dmaengine: shdma: fix a build failure on platforms with no DMA support
On platforms with no support for the shdma dmaengine driver build is
currently failing with
drivers/built-in.o: In function `sh_mobile_sdhi_probe':
drivers/mmc/host/sh_mobile_sdhi.c:170: undefined reference to`shdma_chan_filter'
Fix the breakage by defining shdma_chan_filter to NULL in such
configurations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
[horms+renesas@verge.net.au: Apply change to shdma-base.h instead of sh_dma.h]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
Srinivas Kandagatla [Tue, 9 Jul 2013 07:26:33 +0000 (08:26 +0100)]
ARM: STi: Set correct ARM ERRATAs.
Some of the ARM_ERRATA selection is not done in the initial SOC support
patches. This patch selects 2 new ARM_ERRATA's and removes one which was
actually fixed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
[olof: reorder new errata entries]
Signed-off-by: Olof Johansson <olof@lixom.net>
Srinivas Kandagatla [Tue, 9 Jul 2013 07:26:24 +0000 (08:26 +0100)]
ARM: dts: STi: Fix pinconf setup for STiH416 serial2
This patch fixes a bug in pinctrl setup of serial2 device, Some of the
pins in the pinctrl node of serial2 do not belong to that
pin-controller. This patch divides them in the pins into there
respective pin controller nodes.
Without this patch serial on StiH416-B2000 Board will not work as it
fails with:
"st-pinctrl pin-controller-rear.3: failed to get pin(99) name
st-pinctrl pin-controller-rear.3: maps: function serial2 group serial2-0
num 4
pinconfig core: failed to register map default (3): no group/pin given"
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Sun, 21 Jul 2013 19:05:29 +0000 (12:05 -0700)]
Linux 3.11-rc2
Linus Torvalds [Sun, 21 Jul 2013 17:11:04 +0000 (10:11 -0700)]
Merge tag 'acpi-video-3.11' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI video support fixes from Rafael Wysocki:
"I'm sending a separate pull request for this as it may be somewhat
controversial. The breakage addressed here is not really new and the
fixes may not satisfy all users of the affected systems, but we've had
so much back and forth dance in this area over the last several weeks
that I think it's time to actually make some progress.
The source of the problem is that about a year ago we started to tell
BIOSes that we're compatible with Windows 8, which we really need to
do, because some systems shipping with Windows 8 are tested with it
and nothing else, so if we tell their BIOSes that we aren't compatible
with Windows 8, we expose our users to untested BIOS/AML code paths.
However, as it turns out, some Windows 8-specific AML code paths are
not tested either, because Windows 8 actually doesn't use the ACPI
methods containing them, so if we declare Windows 8 compatibility and
attempt to use those ACPI methods, things break. That occurs mostly
in the backlight support area where in particular the _BCM and _BQC
methods are plain unusable on some systems if the OS declares Windows
8 compatibility.
[ The additional twist is that they actually become usable if the OS
says it is not compatible with Windows 8, but that may cause
problems to show up elsewhere ]
Investigation carried out by Matthew Garrett indicates that what
Windows 8 does about backlight is to leave backlight control up to
individual graphics drivers. At least there's evidence that it does
that if the Intel graphics driver is used, so we've decided to follow
Windows 8 in that respect and allow i915 to control backlight (Daniel
likes that part).
The first commit from Aaron Lu makes ACPICA export the variable from
which we can infer whether or not the BIOS believes that we are
compatible with Windows 8.
The second commit from Matthew Garrett prepares the ACPI video driver
by making it initialize the ACPI backlight even if it is not going to
be used afterward (that is needed for backlight control to work on
Thinkpads).
The third commit implements the actual workaround making i915 take
over backlight control if the firmware thinks it's dealing with
Windows 8 and is based on the work of multiple developers, including
Matthew Garrett, Chun-Yi Lee, Seth Forshee, and Aaron Lu.
The final commit from Aaron Lu makes us follow Windows 8 by informing
the firmware through the _DOS method that it should not carry out
automatic brightness changes, so that brightness can be controlled by
GUI.
Hopefully, this approach will allow us to avoid using blacklists of
systems that should not declare Windows 8 compatibility just to avoid
backlight control problems in the future.
- Change from Aaron Lu makes ACPICA export a variable which can be
used by driver code to determine whether or not the BIOS believes
that we are compatible with Windows 8.
- Change from Matthew Garrett makes the ACPI video driver initialize
the ACPI backlight even if it is not going to be used afterward
(that is needed for backlight control to work on Thinkpads).
- Fix from Rafael J Wysocki implements Windows 8 backlight support
workaround making i915 take over bakclight control if the firmware
thinks it's dealing with Windows 8. Based on the work of multiple
developers including Matthew Garrett, Chun-Yi Lee, Seth Forshee,
and Aaron Lu.
- Fix from Aaron Lu makes the kernel follow Windows 8 by informing
the firmware through the _DOS method that it should not carry out
automatic brightness changes, so that brightness can be controlled
by GUI"
* tag 'acpi-video-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: no automatic brightness changes by win8-compatible firmware
ACPI / video / i915: No ACPI backlight if firmware expects Windows 8
ACPI / video: Always call acpi_video_init_brightness() on init
ACPICA: expose OSI version
Linus Torvalds [Sun, 21 Jul 2013 03:11:42 +0000 (20:11 -0700)]
Merge tag 'ext4_for_linus' of git://git./linux/kernel/git/tytso/ext4
Pull ext[34] tmpfile bugfix from Ted Ts'o:
"Fix regression caused by commit
af51a2ac36d1f which added ->tmpfile()
support (along with a similar fix for ext3)"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext3: fix a BUG when opening a file with O_TMPFILE flag
ext4: fix a BUG when opening a file with O_TMPFILE flag
Zheng Liu [Sun, 21 Jul 2013 02:03:20 +0000 (22:03 -0400)]
ext3: fix a BUG when opening a file with O_TMPFILE flag
When we try to open a file with O_TMPFILE flag, we will trigger a bug.
The root cause is that in ext4_orphan_add() we check ->i_nlink == 0 and
this check always fails because we set ->i_nlink = 1 in
inode_init_always(). We can use the following program to trigger it:
int main(int argc, char *argv[])
{
int fd;
fd = open(argv[1], O_TMPFILE, 0666);
if (fd < 0) {
perror("open ");
return -1;
}
close(fd);
return 0;
}
The oops message looks like this:
kernel: kernel BUG at fs/ext3/namei.c:1992!
kernel: invalid opcode: 0000 [#1] SMP
kernel: Modules linked in: ext4 jbd2 crc16 cpufreq_ondemand ipv6 dm_mirror dm_region_hash dm_log dm_mod parport_pc parport serio_raw sg dcdbas pcspkr i2c_i801 ehci_pci ehci_hcd button acpi_cpufreq mperf e1000e ptp pps_core ttm drm_kms_helper drm hwmon i2c_algo_bit i2c_core ext3 jbd sd_mod ahci libahci libata scsi_mod uhci_hcd
kernel: CPU: 0 PID: 2882 Comm: tst_tmpfile Not tainted 3.11.0-rc1+ #4
kernel: Hardware name: Dell Inc. OptiPlex 780 /0V4W66, BIOS A05 08/11/2010
kernel: task:
ffff880112d30050 ti:
ffff8801124d4000 task.ti:
ffff8801124d4000
kernel: RIP: 0010:[<
ffffffffa00db5ae>] [<
ffffffffa00db5ae>] ext3_orphan_add+0x6a/0x1eb [ext3]
kernel: RSP: 0018:
ffff8801124d5cc8 EFLAGS:
00010202
kernel: RAX:
0000000000000000 RBX:
ffff880111510128 RCX:
ffff8801114683a0
kernel: RDX:
0000000000000000 RSI:
ffff880111510128 RDI:
ffff88010fcf65a8
kernel: RBP:
ffff8801124d5d18 R08:
0080000000000000 R09:
ffffffffa00d3b7f
kernel: R10:
ffff8801114683a0 R11:
ffff8801032a2558 R12:
0000000000000000
kernel: R13:
ffff88010fcf6800 R14:
ffff8801032a2558 R15:
ffff8801115100d8
kernel: FS:
00007f5d172b5700(0000) GS:
ffff880117c00000(0000) knlGS:
0000000000000000
kernel: CS: 0010 DS: 0000 ES: 0000 CR0:
000000008005003b
kernel: CR2:
00007f5d16df15d0 CR3:
0000000110b1d000 CR4:
00000000000407f0
kernel: Stack:
kernel:
000000000000000c ffff8801048a7dc8 ffff8801114685a8 ffffffffa00b80d7
kernel:
ffff8801124d5e38 ffff8801032a2558 ffff88010ce24d68 0000000000000000
kernel:
ffff88011146b300 ffff8801124d5d44 ffff8801124d5d78 ffffffffa00db7e1
kernel: Call Trace:
kernel: [<
ffffffffa00b80d7>] ? journal_start+0x8c/0xbd [jbd]
kernel: [<
ffffffffa00db7e1>] ext3_tmpfile+0xb2/0x13b [ext3]
kernel: [<
ffffffff821076f8>] path_openat+0x11f/0x5e7
kernel: [<
ffffffff821c86b4>] ? list_del+0x11/0x30
kernel: [<
ffffffff82065fa2>] ? __dequeue_entity+0x33/0x38
kernel: [<
ffffffff82107cd5>] do_filp_open+0x3f/0x8d
kernel: [<
ffffffff82112532>] ? __alloc_fd+0x50/0x102
kernel: [<
ffffffff820f9296>] do_sys_open+0x13b/0x1cd
kernel: [<
ffffffff820f935c>] SyS_open+0x1e/0x20
kernel: [<
ffffffff82398c02>] system_call_fastpath+0x16/0x1b
kernel: Code: 39 c7 0f 85 67 01 00 00 0f b7 03 25 00 f0 00 00 3d 00 40 00 00 74 18 3d 00 80 00 00 74 11 3d 00 a0 00 00 74 0a 83 7b 48 00 74 04 <0f> 0b eb fe 49 8b 85 50 03 00 00 4c 89 f6 48 c7 c7 c0 99 0e a0
kernel: RIP [<
ffffffffa00db5ae>] ext3_orphan_add+0x6a/0x1eb [ext3]
kernel: RSP <
ffff8801124d5cc8>
Here we couldn't call clear_nlink() directly because in d_tmpfile() we
will call inode_dec_link_count() to decrease ->i_nlink. So this commit
tries to call d_tmpfile() before ext4_orphan_add() to fix this problem.
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Jan Kara <jack@suse.cz>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Zheng Liu [Sun, 21 Jul 2013 01:58:38 +0000 (21:58 -0400)]
ext4: fix a BUG when opening a file with O_TMPFILE flag
When we try to open a file with O_TMPFILE flag, we will trigger a bug.
The root cause is that in ext4_orphan_add() we check ->i_nlink == 0 and
this check always fails because we set ->i_nlink = 1 in
inode_init_always(). We can use the following program to trigger it:
int main(int argc, char *argv[])
{
int fd;
fd = open(argv[1], O_TMPFILE, 0666);
if (fd < 0) {
perror("open ");
return -1;
}
close(fd);
return 0;
}
The oops message looks like this:
kernel BUG at fs/ext4/namei.c:2572!
invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
Modules linked in: dlci bridge stp hidp cmtp kernelcapi l2tp_ppp l2tp_netlink l2tp_core sctp libcrc32c rfcomm tun fuse nfnetli
nk can_raw ipt_ULOG can_bcm x25 scsi_transport_iscsi ipx p8023 p8022 appletalk phonet psnap vmw_vsock_vmci_transport af_key vmw_vmci rose vsock atm can netrom ax25 af_rxrpc ir
da pppoe pppox ppp_generic slhc bluetooth nfc rfkill rds caif_socket caif crc_ccitt af_802154 llc2 llc snd_hda_codec_realtek snd_hda_intel snd_hda_codec serio_raw snd_pcm pcsp
kr edac_core snd_page_alloc snd_timer snd soundcore r8169 mii sr_mod cdrom pata_atiixp radeon backlight drm_kms_helper ttm
CPU: 1 PID:
1812571 Comm: trinity-child2 Not tainted 3.11.0-rc1+ #12
Hardware name: Gigabyte Technology Co., Ltd. GA-MA78GM-S2H/GA-MA78GM-S2H, BIOS F12a 04/23/2010
task:
ffff88007dfe69a0 ti:
ffff88010f7b6000 task.ti:
ffff88010f7b6000
RIP: 0010:[<
ffffffff8125ce69>] [<
ffffffff8125ce69>] ext4_orphan_add+0x299/0x2b0
RSP: 0018:
ffff88010f7b7cf8 EFLAGS:
00010202
RAX:
0000000000000000 RBX:
ffff8800966d3020 RCX:
0000000000000000
RDX:
0000000000000000 RSI:
ffff88007dfe70b8 RDI:
0000000000000001
RBP:
ffff88010f7b7d40 R08:
ffff880126a3c4e0 R09:
ffff88010f7b7ca0
R10:
0000000000000000 R11:
0000000000000000 R12:
ffff8801271fd668
R13:
ffff8800966d2f78 R14:
ffff88011d7089f0 R15:
ffff88007dfe69a0
FS:
00007f70441a3740(0000) GS:
ffff88012a800000(0000) knlGS:
00000000f77c96c0
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000002834000 CR3:
0000000107964000 CR4:
00000000000007e0
DR0:
0000000000780000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000ffff0ff0 DR7:
0000000000000600
Stack:
0000000000002000 00000020810b6dde 0000000000000000 ffff88011d46db00
ffff8800966d3020 ffff88011d7089f0 ffff88009c7f4c10 ffff88010f7b7f2c
ffff88007dfe69a0 ffff88010f7b7da8 ffffffff8125cfac ffff880100000004
Call Trace:
[<
ffffffff8125cfac>] ext4_tmpfile+0x12c/0x180
[<
ffffffff811cba78>] path_openat+0x238/0x700
[<
ffffffff8100afc4>] ? native_sched_clock+0x24/0x80
[<
ffffffff811cc647>] do_filp_open+0x47/0xa0
[<
ffffffff811db73f>] ? __alloc_fd+0xaf/0x200
[<
ffffffff811ba2e4>] do_sys_open+0x124/0x210
[<
ffffffff81010725>] ? syscall_trace_enter+0x25/0x290
[<
ffffffff811ba3ee>] SyS_open+0x1e/0x20
[<
ffffffff816ca8d4>] tracesys+0xdd/0xe2
[<
ffffffff81001001>] ? start_thread_common.constprop.6+0x1/0xa0
Code: 04 00 00 00 89 04 24 31 c0 e8 c4 77 04 00 e9 43 fe ff ff 66 25 00 d0 66 3d 00 80 0f 84 0e fe ff ff 83 7b 48 00 0f 84 04 fe ff ff <0f> 0b 49 8b 8c 24 50 07 00 00 e9 88 fe ff ff 0f 1f 84 00 00 00
Here we couldn't call clear_nlink() directly because in d_tmpfile() we
will call inode_dec_link_count() to decrease ->i_nlink. So this commit
tries to call d_tmpfile() before ext4_orphan_add() to fix this problem.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Tested-by: Darrick J. Wong <darrick.wong@oracle.com>
Tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Sat, 20 Jul 2013 22:42:38 +0000 (15:42 -0700)]
Merge tag 'staging-3.11-rc2' of git://git./linux/kernel/git/gregkh/staging
Pull staging tree fixes from Greg KH:
"Here are a few iio driver fixes for 3.11-rc2. They are still spread
across drivers/iio and drivers/staging/iio so they are coming in
through this tree.
I've also removed the drivers/staging/csr/ driver as the developers
who originally sent it to me have moved on to other companies, and CSR
still will not send us the specs for the device, making the driver
pretty much obsolete and impossible to fix up. Deleting it now
prevents people from sending in lots of tiny codingsyle fixes that
will never go anywhere.
It also helps to offset the large lustre filesystem merge that
happened in 3.11-rc1 in the overall 3.11.0 diffstat. :)"
* tag 'staging-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: csr: remove driver
iio: lps331ap: Fix wrong in_pressure_scale output value
iio staging: fix lis3l02dq, read error handling
staging:iio:ad7291: add missing .driver_module to struct iio_info
iio: ti_am335x_adc: add missing .driver_module to struct iio_info
iio: mxs-lradc: Remove useless check in read_raw
iio: mxs-lradc: Fix misuse of iio->trig
iio: inkern: fix iio_convert_raw_to_processed_unlocked
iio: Fix iio_channel_has_info
iio:trigger: device_unregister->device_del to avoid double free
iio: dac: ad7303: fix error return code in ad7303_probe()
Linus Torvalds [Sat, 20 Jul 2013 17:50:01 +0000 (10:50 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"The sget() one is a long-standing bug and will need to go into -stable
(in fact, it had been originally caught in RHEL6), the other two are
3.11-only"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: constify dentry parameter in d_count()
livelock avoidance in sget()
allow O_TMPFILE to work with O_WRONLY
Linus Torvalds [Sat, 20 Jul 2013 17:48:59 +0000 (10:48 -0700)]
Merge tag 'ext4_for_linus' of git://git./linux/kernel/git/tytso/ext4
Pull ext4 bugfixes from Ted Ts'o:
"Fixes for 3.11-rc2, sent at 5pm, in the professoinal style. :-)"
I'm not sure I like this new level of "professionalism".
9-5, people, 9-5.
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: call ext4_es_lru_add() after handling cache miss
ext4: yield during large unlinks
ext4: make the extent_status code more robust against ENOMEM failures
ext4: simplify calculation of blocks to free on error
ext4: fix error handling in ext4_ext_truncate()
Linus Torvalds [Sat, 20 Jul 2013 17:48:24 +0000 (10:48 -0700)]
Merge tag 'nfs-for-3.11-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Fix a regression against NFSv4 FreeBSD servers when creating a new
file
- Fix another regression in rpc_client_register()
* tag 'nfs-for-3.11-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Fix a regression against the FreeBSD server
SUNRPC: Fix another issue with rpc_client_register()
Linus Torvalds [Sat, 20 Jul 2013 17:47:38 +0000 (10:47 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/josef/btrfs-next
Pull btrfs fixes from Josef Bacik:
"I'm playing the role of Chris Mason this week while he's on vacation.
There are a few critical fixes for btrfs here, all regressions and
have been tested well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/josef/btrfs-next:
Btrfs: fix wrong write offset when replacing a device
Btrfs: re-add root to dead root list if we stop dropping it
Btrfs: fix lock leak when resuming snapshot deletion
Btrfs: update drop progress before stopping snapshot dropping
Linus Walleij [Thu, 20 Jun 2013 11:48:16 +0000 (13:48 +0200)]
ARM: nomadik: configure for NO_HZ and HRTIMERS
This enables tickless idle (NO_HZ_IDLE) and high resolution
timers for the Nomadik.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Tue, 28 May 2013 14:40:29 +0000 (16:40 +0200)]
ARM: nomadik: update defconfig base
Update the Nomadik defconfig enabling:
- GPIO keyboard input
- Regulators
- LED class driver
- LED heartbeat trigger
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Ulf Hansson [Mon, 27 May 2013 13:16:06 +0000 (15:16 +0200)]
ARM: nomadik: Update MMC defconfigs
Enable MMC_UNSAFE_RESUME to accomplish a proper suspend/resume cycle
for SD/SDIO/(e)MMC.
ARMMMCI host driver supports clock gating through runtime PM, thus
MMC_CLKGATE is not needed. Moreover ARMMMCI can do scatter-gather which
means we can explicity disable MMC_BLOCK_BOUNCE, since it's default
enabled, to skip unnecessary bounce buffer copying.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Peng Tao [Thu, 18 Jul 2013 14:09:08 +0000 (22:09 +0800)]
vfs: constify dentry parameter in d_count()
so that it can be used in places like d_compare/d_hash
without causing a compiler warning.
Signed-off-by: Peng Tao <tao.peng@emc.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Fri, 19 Jul 2013 23:13:55 +0000 (03:13 +0400)]
livelock avoidance in sget()
Eric Sandeen has found a nasty livelock in sget() - take a mount(2) about
to fail. The superblock is on ->fs_supers, ->s_umount is held exclusive,
->s_active is 1. Along comes two more processes, trying to mount the same
thing; sget() in each is picking that superblock, bumping ->s_count and
trying to grab ->s_umount. ->s_active is 3 now. Original mount(2)
finally gets to deactivate_locked_super() on failure; ->s_active is 2,
superblock is still ->fs_supers because shutdown will *not* happen until
->s_active hits 0. ->s_umount is dropped and now we have two processes
chasing each other:
s_active = 2, A acquired ->s_umount, B blocked
A sees that the damn thing is stillborn, does deactivate_locked_super()
s_active = 1, A drops ->s_umount, B gets it
A restarts the search and finds the same superblock. And bumps it ->s_active.
s_active = 2, B holds ->s_umount, A blocked on trying to get it
... and we are in the earlier situation with A and B switched places.
The root cause, of course, is that ->s_active should not grow until we'd
got MS_BORN. Then failing ->mount() will have deactivate_locked_super()
shut the damn thing down. Fortunately, it's easy to do - the key point
is that grab_super() is called only for superblocks currently on ->fs_supers,
so it can bump ->s_count and grab ->s_umount first, then check MS_BORN and
bump ->s_active; we must never increment ->s_count for superblocks past
->kill_sb(), but grab_super() is never called for those.
The bug is pretty old; we would've caught it by now, if not for accidental
exclusion between sget() for block filesystems; the things like cgroup or
e.g. mtd-based filesystems don't have anything of that sort, so they get
bitten. The right way to deal with that is obviously to fix sget()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Fri, 19 Jul 2013 23:11:32 +0000 (03:11 +0400)]
allow O_TMPFILE to work with O_WRONLY
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Fri, 19 Jul 2013 22:11:09 +0000 (15:11 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/rw/uml
Pull UML fixes from Richard Weinberger:
"Special thanks goes to Toralf Föster for continuously testing UML and
reporting issues!"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: remove dead code
um: siginfo cleanup
uml: Fix which_tmpdir failure when /dev/shm is a symlink, and in other edge cases
um: Fix wait_stub_done() error handling
um: Mark stub pages mapping with VM_PFNMAP
um: Fix return value of strnlen_user()
Linus Torvalds [Fri, 19 Jul 2013 22:10:01 +0000 (15:10 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"MIPS fixes for 3.11. Half of then is for Netlogic the remainder
touches things across arch/mips.
Nothing really dramatic and by rc1 standards MIPS will be in fairly
good shape with this applied. Tested by building all MIPS defconfigs
of which with this pull request four platforms won't build. And yes,
it boots also on my favorite test systems"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: kvm: Kconfig: Drop HAVE_KVM dependency from VIRTUALIZATION
MIPS: Octeon: Fix DT pruning bug with pip ports
MIPS: KVM: Mark KVM_GUEST (T&E KVM) as BROKEN_ON_SMP
MIPS: tlbex: fix broken build in v3.11-rc1
MIPS: Netlogic: Add XLP PIC irqdomain
MIPS: Netlogic: Fix USB block's coherent DMA mask
MIPS: tlbex: Fix typo in r3000 tlb store handler
MIPS: BMIPS: Fix thinko to release slave TP from reset
MIPS: Delete dead invocation of exception_exit().
Linus Torvalds [Fri, 19 Jul 2013 22:08:53 +0000 (15:08 -0700)]
Merge tag 'arm64-stable' of git://git./linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 fixes from Catalin Marinas:
- Post -rc1 update to the common reboot infrastructure.
- Fixes (user cache maintenance fault handling, !COMPAT compilation,
CPU online and interrupt hanlding).
* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: use common reboot infrastructure
arm64: mm: don't treat user cache maintenance faults as writes
arm64: add '#ifdef CONFIG_COMPAT' for aarch32_break_handler()
arm64: Only enable local interrupts after the CPU is marked online
Linus Torvalds [Fri, 19 Jul 2013 22:08:12 +0000 (15:08 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"An update for the BFP jit to the latest and greatest, two patches to
get kdump working again, the random-abort ptrace extention for
transactional execution, the z90crypt module alias for ap and a tiny
cleanup"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/zcrypt: Alias for new zcrypt device driver base module
s390/kdump: Allow copy_oldmem_page() copy to virtual memory
s390/kdump: Disable mmap for s390
s390/bpf,jit: add pkt_type support
s390/bpf,jit: address randomize and write protect jit code
s390/bpf,jit: use generic jit dumper
s390/bpf,jit: call module_free() from any context
s390/qdio: remove unused variable
s390/ptrace: PTRACE_TE_ABORT_RAND
Stefan Behrens [Thu, 4 Jul 2013 14:14:23 +0000 (16:14 +0200)]
Btrfs: fix wrong write offset when replacing a device
Miao Xie reported the following issue:
The filesystem was corrupted after we did a device replace.
Steps to reproduce:
# mkfs.btrfs -f -m single -d raid10 <device0>..<device3>
# mount <device0> <mnt>
# btrfs replace start -rfB 1 <device4> <mnt>
# umount <mnt>
# btrfsck <device4>
The reason for the issue is that we changed the write offset by mistake,
introduced by commit
625f1c8dc.
We read the data from the source device at first, and then write the
data into the corresponding place of the new device. In order to
implement the "-r" option, the source location is remapped using
btrfs_map_block(). The read takes place on the mapped location, and
the write needs to take place on the unmapped location. Currently
the write is using the mapped location, and this commit changes it
back by undoing the change to the write address that the aforementioned
commit added by mistake.
Reported-by: Miao Xie <miaox@cn.fujitsu.com>
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Josef Bacik [Wed, 17 Jul 2013 23:30:20 +0000 (19:30 -0400)]
Btrfs: re-add root to dead root list if we stop dropping it
If we stop dropping a root for whatever reason we need to add it back to the
dead root list so that we will re-start the dropping next transaction commit.
The other case this happens is if we recover a drop because we will add a root
without adding it to the fs radix tree, so we can leak it's root and commit root
extent buffer, adding this to the dead root list makes this cleanup happen.
Thanks,
Cc: stable@vger.kernel.org
Reported-by: Alex Lyakas <alex.btrfs@zadarastorage.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Josef Bacik [Mon, 15 Jul 2013 16:41:42 +0000 (12:41 -0400)]
Btrfs: fix lock leak when resuming snapshot deletion
We aren't setting path->locks[level] when we resume a snapshot deletion which
means we won't unlock the buffer when we free the path. This causes deadlocks
if we happen to re-allocate the block before we've evicted the extent buffer
from cache. Thanks,
Cc: stable@vger.kernel.org
Reported-by: Alex Lyakas <alex.btrfs@zadarastorage.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Josef Bacik [Mon, 15 Jul 2013 15:57:06 +0000 (11:57 -0400)]
Btrfs: update drop progress before stopping snapshot dropping
Alex pointed out a problem and fix that exists in the drop one snapshot at a
time patch. If we decide we need to exit for whatever reason (umount for
example) we will just exit the snapshot dropping without updating the drop
progress. So the next time we go to resume we will BUG_ON() because we can't
find the extent we left off at because we never updated it. This patch fixes
the problem.
Cc: stable@vger.kernel.org
Reported-by: Alex Lyakas <alex.btrfs@zadarastorage.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Linus Torvalds [Fri, 19 Jul 2013 17:17:12 +0000 (10:17 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fix from Paolo Bonzini:
"This single patch fixes a regression caused by one of the
optimizations introduced in 3.11, which is generally visible only on
AMD processors"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: MMU: avoid fast page fault fixing mmio page fault
Linus Torvalds [Fri, 19 Jul 2013 16:59:06 +0000 (09:59 -0700)]
Merge tag 'pm+acpi-3.11-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are fixes collected over the last week, most importnatly two
cpufreq reverts fixing regressions introduced in 3.10, an autoseelp
fix preventing systems using it from crashing during shutdown and two
ACPI scan fixes related to hotplug.
Specifics:
- Two cpufreq commits from the 3.10 cycle introduced regressions.
The first of them was buggy (it did way much more than it needed to
do) and the second one attempted to fix an issue introduced by the
first one. Fixes from Srivatsa S Bhat revert both.
- If autosleep triggers during system shutdown and the shutdown
callbacks of some device drivers have been called already, it may
crash the system. Fix from Liu Shuo prevents that from happening
by making try_to_suspend() check system_state.
- The ACPI memory hotplug driver doesn't clear its driver_data on
errors which may cause a NULL poiter dereference to happen later.
Fix from Toshi Kani.
- The ACPI namespace scanning code should not try to attach scan
handlers to device objects that have them already, which may
confuse things quite a bit, and it should rescan the whole
namespace branch starting at the given node after receiving a bus
check notify event even if the device at that particular node has
been discovered already. Fixes from Rafael J Wysocki.
- New ACPI video blacklist entry for a system whose initial backlight
setting from the BIOS doesn't make sense. From Lan Tianyu.
- Garbage string output avoindance for ACPI PNP from Liu Shuo.
- Two Kconfig fixes for issues introduced recently in the s3c24xx
cpufreq driver (when moving the driver to drivers/cpufreq) from
Paul Bolle.
- Trivial comment fix in pm_wakeup.h from Chanwoo Choi"
* tag 'pm+acpi-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: ignore BIOS initial backlight value for Fujitsu E753
PNP / ACPI: avoid garbage in resource name
cpufreq: Revert commit
2f7021a8 to fix CPU hotplug regression
cpufreq: s3c24xx: fix "depends on ARM_S3C24XX" in Kconfig
cpufreq: s3c24xx: rename CONFIG_CPU_FREQ_S3C24XX_DEBUGFS
PM / Sleep: Fix comment typo in pm_wakeup.h
PM / Sleep: avoid 'autosleep' in shutdown progress
cpufreq: Revert commit a66b2e to fix suspend/resume regression
ACPI / memhotplug: Fix a stale pointer in error path
ACPI / scan: Always call acpi_bus_scan() for bus check notifications
ACPI / scan: Do not try to attach scan handlers to devices having them
Marc Zyngier [Thu, 11 Jul 2013 11:13:00 +0000 (12:13 +0100)]
arm64: use common reboot infrastructure
Commit
7b6d864b48d9 (reboot: arm: change reboot_mode to use enum
reboot_mode) changed the way reboot is handled on arm, which has a
direct impact on arm64 as we share the reset driver on the VE platform.
The obvious fix is to move arm64 to use the same infrastructure.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[catalin.marinas@arm.com: removed reboot_mode = REBOOT_HARD default setting]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Will Deacon [Fri, 19 Jul 2013 14:37:12 +0000 (15:37 +0100)]
arm64: mm: don't treat user cache maintenance faults as writes
On arm64, cache maintenance faults appear as data aborts with the CM
bit set in the ESR. The WnR bit, usually used to distinguish between
faulting loads and stores, always reads as 1 and (slightly confusingly)
the instructions are treated as reads by the architecture.
This patch fixes our fault handling code to treat cache maintenance
faults in the same way as loads.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Chen Gang [Mon, 24 Jun 2013 09:27:49 +0000 (10:27 +0100)]
arm64: add '#ifdef CONFIG_COMPAT' for aarch32_break_handler()
If 'COMPAT' not defined, aarch32_break_handler() cannot pass compiling,
and it can work independent with 'COMPAT', so remove dummy definition.
The related error:
arch/arm64/kernel/debug-monitors.c:249:5: error: redefinition of ‘aarch32_break_handler’
In file included from arch/arm64/kernel/debug-monitors.c:29:0:
/root/linux-next/arch/arm64/include/asm/debug-monitors.h:89:12: note: previous definition of ‘aarch32_break_handler’ was here
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Catalin Marinas [Fri, 19 Jul 2013 14:08:15 +0000 (15:08 +0100)]
arm64: Only enable local interrupts after the CPU is marked online
There is a slight chance that (timer) interrupts are triggered before a
secondary CPU has been marked online with implications on softirq thread
affinity.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Kirill Tkhai <tkhai@yandex.ru>
Markos Chandras [Tue, 11 Jun 2013 09:02:33 +0000 (09:02 +0000)]
MIPS: kvm: Kconfig: Drop HAVE_KVM dependency from VIRTUALIZATION
Virtualization does not always need KVM capabilities so drop the
dependency. The KVM symbol already depends on HAVE_KVM.
Fixes the following problem on a randconfig:
warning: (REMOTEPROC && RPMSG) selects VIRTUALIZATION which has unmet direct
dependencies (HAVE_KVM)
warning: (REMOTEPROC && RPMSG) selects VIRTUALIZATION which has unmet
direct dependencies (HAVE_KVM)
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5443/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Tony Lindgren [Fri, 19 Jul 2013 10:28:35 +0000 (03:28 -0700)]
Merge branch 'omap-for-v3.11/dt-fixes' into omap-for-v3.11/fixes
Richard Weinberger [Fri, 19 Jul 2013 09:35:32 +0000 (11:35 +0200)]
um: remove dead code
"me" is not used.
Signed-off-by: Richard Weinberger <richard@nod.at>
Richard Weinberger [Fri, 19 Jul 2013 09:31:36 +0000 (11:31 +0200)]
um: siginfo cleanup
Currently we use both struct siginfo and siginfo_t.
Let's use struct siginfo internally to avoid ongoing
compiler warning. We are allowed to do so because
struct siginfo and siginfo_t are equivalent.
Signed-off-by: Richard Weinberger <richard@nod.at>
Faidon Liambotis [Thu, 11 Jul 2013 21:08:09 +0000 (21:08 +0000)]
MIPS: Octeon: Fix DT pruning bug with pip ports
During the pruning of the device tree octeon_fdt_pip_iface() is called
for each PIP interface and every port up to the port count is removed
from the device tree. However, the count was set to the return value of
cvmx_helper_interface_enumerate() which doesn't actually return the
count but just returns zero on success. This effectively removed *all*
ports from the tree.
Use cvmx_helper_ports_on_interface() instead to fix this. This
successfully restores the 3 ports of my ERLite-3 and fixes the "kernel
assigns random MAC addresses" issue.
Signed-off-by: Faidon Liambotis <paravoid@debian.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5587/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Tristan Schmelcher [Mon, 8 Jul 2013 20:19:49 +0000 (16:19 -0400)]
uml: Fix which_tmpdir failure when /dev/shm is a symlink, and in other edge cases
which_tmpdir did the wrong thing if /dev/shm was a symlink (e.g., to /run/shm),
if there were multiple mounts on top of each other, if the mount(s) were
obscured by a later mount, or if /dev/shm was a prefix of another mount point.
This fixes these cases. Applies to 3.9.6.
Signed-off-by: Tristan Schmelcher <tschmelcher@google.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Richard Weinberger [Fri, 17 May 2013 12:21:01 +0000 (14:21 +0200)]
um: Fix wait_stub_done() error handling
If we die within a stub handler we only way to reliable
kill the (obviously) dying uml guest process is killing
it's host twin on the host side.
Signed-off-by: Richard Weinberger <richard@nod.at>
Richard Weinberger [Sun, 12 May 2013 21:26:03 +0000 (23:26 +0200)]
um: Mark stub pages mapping with VM_PFNMAP
Ensure that a process cannot destroy his stub pages with
using MADV_DONTNEED and friends.
Reported-by: toralf.foerster@gmx.de
Signed-off-by: Richard Weinberger <richard@nod.at>
Richard Weinberger [Sat, 11 May 2013 13:35:32 +0000 (15:35 +0200)]
um: Fix return value of strnlen_user()
In case of an error it must not return -EFAULT.
Return 0 like all other archs do.
Reported-by: toralf.foerster@gmx.de
Signed-off-by: Richard Weinberger <richard@nod.at>
James Hogan [Fri, 12 Jul 2013 10:26:11 +0000 (10:26 +0000)]
MIPS: KVM: Mark KVM_GUEST (T&E KVM) as BROKEN_ON_SMP
Make KVM_GUEST depend on BROKEN_ON_SMP so that it cannot be enabled with
SMP.
SMP kernels use ll/sc instructions for an atomic section in the tlb fill
handler, with a tlbp instruction contained in the middle. This cannot be
emulated with trap & emulate KVM because the tlbp instruction traps and
the eret to return to the guest code clears the LLbit which makes the sc
instruction always fail.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5588/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Aaro Koskinen [Mon, 15 Jul 2013 07:21:57 +0000 (07:21 +0000)]
MIPS: tlbex: fix broken build in v3.11-rc1
Commit
6ba045f9fbdafb48da42aa8576ea7a3980443136 (MIPS: Move generated code
to .text for microMIPS) deleted tlbmiss_handler_setup_pgd_array, but some
references were not converted. Fix that to enable building a MIPS kernel.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Jayachandran C. <jchandra@broadcom.com>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5589/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Jayachandran C [Wed, 17 Jul 2013 10:27:26 +0000 (10:27 +0000)]
MIPS: Netlogic: Add XLP PIC irqdomain
Add a legacy irq domain for the XLP PIC interrupts. This will be used
when interrupts are assigned from the device tree. This change is required
after commit
c5cdc67 "irqdomain: Remove temporary MIPS workaround code".
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Cc: Jayachandran C <jchandra@broadcom.com>
Patchwork: https://patchwork.linux-mips.org/patch/5597/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ganesan Ramalingam [Wed, 17 Jul 2013 10:27:25 +0000 (10:27 +0000)]
MIPS: Netlogic: Fix USB block's coherent DMA mask
The on-chip USB controller on Netlogic XLP does not suppport
DMA beyond 32-bit physical address. Set the coherent_dma_mask
of the USB in its PCI fixup to support this.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C. <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5596/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Tony Wu [Thu, 18 Jul 2013 09:45:47 +0000 (09:45 +0000)]
MIPS: tlbex: Fix typo in r3000 tlb store handler
commit
6ba045f (MIPS: Move generated code to .text for microMIPS)
causes a panic at boot. The handler builder should test against
handle_tlbs_end, not handle_tlbs.
Signed-off-by: Tony Wu <tung7970@gmail.com>
Acked-by: Jayachandran C. <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5600/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Florian Fainelli [Wed, 17 Jul 2013 17:56:31 +0000 (17:56 +0000)]
MIPS: BMIPS: Fix thinko to release slave TP from reset
Commit
4df715aa ["MIPS: BMIPS: support booting from physical CPU other
than 0"] introduced a thinko which will prevents slave CPUs from being
released from reset on systems where we boot from TP0. The problem is
that we are checking whether the slave CPU logical CPU map is 0, which
is never true for systems booting from TP0, so we do not release the
slave TP from reset and we are just stuck. Fix this by properly checking
that the CPU we intend to boot really is the physical slave CPU (logical
and physical value being 1).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: Florian Fainelli <florian@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/5598/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ingo Tuchscherer [Thu, 18 Jul 2013 14:28:26 +0000 (16:28 +0200)]
s390/zcrypt: Alias for new zcrypt device driver base module
The zcrypt device driver has been split into base/bus module, api-module,
card modules and message type modules. The base module has been renamed
from z90crypt to ap.
A module alias (with the well-known z90crypt identifier) will be introduced
that enable users to use their existing way to load the zcrypt device driver.
Signed-off-by: Ingo Tuchscherer <ingo.tuchscherer@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Linus Torvalds [Fri, 19 Jul 2013 03:08:47 +0000 (20:08 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
"A couple interesting SKB fragment handling fixes, plus the usual small
bits here and there:
1) Fix 64-bit divide build failure on 32-bit platforms in mlx5, from
Tim Gardner.
2) Get rid of a stupid reimplementation on "%*phC" in our sysfs MAC
address printing helper.
3) Fix NETIF_F_SG capability advertisement in hyperv driver, if the
device can't do checksumming offloads then it shouldn't say it can
do SG either. From Haiyang Zhang.
4) bgmac needs to depend on PHYLIB, from Hauke Mehrtens.
5) Don't leak DMA mappings on mapping failures, from Neil Horman.
6) We need to reset the transport header of SKBs in ipv4 before we
attempt to perform early socket demux, just like ipv6 does. From
Eric Dumazet.
7) Add missing locking on vxlan device removal, from Stephen
Hemminger.
8) xen-netfront has to make two passes over an SKB to prepare it for
transfer. One pass calculates the number of slots needed, the
second massages the SKB and fills the slots. Unfortunately, the
first pass doesn't calculate the number of slots properly so we
can end up trying to build a MAX_SKB_FRAGS + 1 SKB which doesn't
work out so well. Fix from Jan Beulich with help and discussion
with several others.
9) Fix a similar problem in tun and macvtap, which have to split up
scatter-gather elements at PAGE_SIZE boundaries. Don't do
zerocopy if it would result in a > MAX_SKB_FRAGS skb. Fixes from
Jason Wang.
10) On receive, once we've decoded the VLAN state completely, clear
skb->vlan_tci. Otherwise demuxed tunnels underneath can trigger
the VLAN code again, corrupting the packet. Fix from Eric
Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
vlan: fix a race in egress prio management
vlan: mask vlan prio bits
macvtap: do not zerocopy if iov needs more pages than MAX_SKB_FRAGS
tuntap: do not zerocopy if iov needs more pages than MAX_SKB_FRAGS
pkt_sched: sch_qfq: remove a source of high packet delay/jitter
xen-netfront: pull on receive skb may need to happen earlier
vxlan: add necessary locking on device removal
hyperv: Fix the NETIF_F_SG flag setting in netvsc
net: Fix sysfs_format_mac() code duplication.
be2net: Fix to avoid hardware workaround when not needed
macvtap: do not assume 802.1Q when send vlan packets
macvtap: fix the missing ret value of TUNSETQUEUE
ipv4: set transport header earlier
mlx5 core: Fix __udivdi3 when compiling for 32 bit arches
bgmac: add dependency to phylib
net/irda: fixed style issues in irlan_eth
ethtool: fixed trailing statements in ethtool
ndisc: bool initializations should use true and false
atl1e: unmap partially mapped skb on dma error and free skb
Linus Torvalds [Fri, 19 Jul 2013 00:39:05 +0000 (17:39 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"Trying again to get the fixes queue, including the fixed IDT alignment
patch.
The UEFI patch is by far the biggest issue at hand: it is currently
causing quite a few machines to boot. Which is sad, because the only
reason they would is because their BIOSes touch memory that has
already been freed. The other major issue is that we finally have
tracked down the root cause of a significant number of machines
failing to suspend/resume"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Make sure IDT is page aligned
x86, suspend: Handle CPUs which fail to #GP on RDMSR
x86/platform/ce4100: Add header file for reboot type
Revert "UEFI: Don't pass boot services regions to SetVirtualAddressMap()"
efivars: check for EFI_RUNTIME_SERVICES
Linus Torvalds [Fri, 19 Jul 2013 00:37:46 +0000 (17:37 -0700)]
Merge tag 'md-3.11-fixes' of git://neil.brown.name/md
Pull md bug fixes from NeilBrown:
"Sorry boss, back at work now boss. Here's them nice shiny patches ya
wanted. All nicely tagged and justified for -stable and everyfing:
Three bug fixes for md in 3.10
3.10 wasn't a good release for md. The bio changes left a couple of
bugs, and an md "fix" created another one.
These three patches appear to fix the issues and have been tagged for
-stable"
* tag 'md-3.11-fixes' of git://neil.brown.name/md:
md/raid1: fix bio handling problems in process_checks()
md: Remove recent change which allows devices to skip recovery.
md/raid10: fix two problems with RAID10 resync.
Linus Torvalds [Thu, 18 Jul 2013 21:01:08 +0000 (14:01 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"You'll be terribly disappointed in this, I'm not trying to sneak any
features in or anything, its mostly radeon and intel fixes, a couple
of ARM driver fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (34 commits)
drm/radeon/dpm: add debugfs support for RS780/RS880 (v3)
drm/radeon/dpm/atom: fix broken gcc harder
drm/radeon/dpm/atom: restructure logic to work around a compiler bug
drm/radeon/dpm: fix atom vram table parsing
drm/radeon: fix an endian bug in atom table parsing
drm/radeon: add a module parameter to disable aspm
drm/rcar-du: Use the GEM PRIME helpers
drm/shmobile: Use the GEM PRIME helpers
uvesafb: Really allow mtrr being 0, as documented and warn()ed
radeon kms: do not flush uninitialized hotplug work
drm/radeon/dpm/sumo: handle boost states properly when forcing a perf level
drm/radeon: align VM PTBs (Page Table Blocks) to 32K
drm/radeon: allow selection of alignment in the sub-allocator
drm/radeon: never unpin UVD bo v3
drm/radeon: fix UVD fence emit
drm/radeon: add fault decode function for CIK
drm/radeon: add fault decode function for SI (v2)
drm/radeon: add fault decode function for cayman/TN (v2)
drm/radeon: use radeon device for request firmware
drm/radeon: add missing ttm_eu_backoff_reservation to radeon_bo_list_validate
...
Eric Dumazet [Thu, 18 Jul 2013 16:35:10 +0000 (09:35 -0700)]
vlan: fix a race in egress prio management
egress_priority_map[] hash table updates are protected by rtnl,
and we never remove elements until device is dismantled.
We have to make sure that before inserting an new element in hash table,
all its fields are committed to memory or else another cpu could
find corrupt values and crash.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 18 Jul 2013 14:19:26 +0000 (07:19 -0700)]
vlan: mask vlan prio bits
In commit
48cc32d38a52d0b68f91a171a8d00531edc6a46e
("vlan: don't deliver frames for unknown vlans to protocols")
Florian made sure we set pkt_type to PACKET_OTHERHOST
if the vlan id is set and we could find a vlan device for this
particular id.
But we also have a problem if prio bits are set.
Steinar reported an issue on a router receiving IPv6 frames with a
vlan tag of 4000 (id 0, prio 2), and tunneled into a sit device,
because skb->vlan_tci is set.
Forwarded frame is completely corrupted : We can see (8100:4000)
being inserted in the middle of IPv6 source address :
16:48:00.780413 IP6 2001:16d8:8100:4000:ee1c:0:9d9:bc87 >
9f94:4d95:2001:67c:29f4::: ICMP6, unknown icmp6 type (0), length 64
0x0000: 0000 0029 8000 c7c3 7103 0001 a0ae e651
0x0010: 0000 0000 ccce 0b00 0000 0000 1011 1213
0x0020: 1415 1617 1819 1a1b 1c1d 1e1f 2021 2223
0x0030: 2425 2627 2829 2a2b 2c2d 2e2f 3031 3233
It seems we are not really ready to properly cope with this right now.
We can probably do better in future kernels :
vlan_get_ingress_priority() should be a netdev property instead of
a per vlan_dev one.
For stable kernels, lets clear vlan_tci to fix the bugs.
Reported-by: Steinar H. Gunderson <sesse@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Thu, 18 Jul 2013 02:55:16 +0000 (10:55 +0800)]
macvtap: do not zerocopy if iov needs more pages than MAX_SKB_FRAGS
We try to linearize part of the skb when the number of iov is greater than
MAX_SKB_FRAGS. This is not enough since each single vector may occupy more than
one pages, so zerocopy_sg_fromiovec() may still fail and may break the guest
network.
Solve this problem by calculate the pages needed for iov before trying to do
zerocopy and switch to use copy instead of zerocopy if it needs more than
MAX_SKB_FRAGS.
This is done through introducing a new helper to count the pages for iov, and
call uarg->callback() manually when switching from zerocopy to copy to notify
vhost.
We can do further optimization on top.
This bug were introduced from
b92946e2919134ebe2a4083e4302236295ea2a73
(macvtap: zerocopy: validate vectors before building skb).
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Thu, 18 Jul 2013 02:55:15 +0000 (10:55 +0800)]
tuntap: do not zerocopy if iov needs more pages than MAX_SKB_FRAGS
We try to linearize part of the skb when the number of iov is greater than
MAX_SKB_FRAGS. This is not enough since each single vector may occupy more than
one pages, so zerocopy_sg_fromiovec() may still fail and may break the guest
network.
Solve this problem by calculate the pages needed for iov before trying to do
zerocopy and switch to use copy instead of zerocopy if it needs more than
MAX_SKB_FRAGS.
This is done through introducing a new helper to count the pages for iov, and
call uarg->callback() manually when switching from zerocopy to copy to notify
vhost.
We can do further optimization on top.
The bug were introduced from commit
0690899b4d4501b3505be069b9a687e68ccbe15b
(tun: experimental zero copy tx support)
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Valente [Tue, 16 Jul 2013 06:52:30 +0000 (08:52 +0200)]
pkt_sched: sch_qfq: remove a source of high packet delay/jitter
QFQ+ inherits from QFQ a design choice that may cause a high packet
delay/jitter and a severe short-term unfairness. As QFQ, QFQ+ uses a
special quantity, the system virtual time, to track the service
provided by the ideal system it approximates. When a packet is
dequeued, this quantity must be incremented by the size of the packet,
divided by the sum of the weights of the aggregates waiting to be
served. Tracking this sum correctly is a non-trivial task, because, to
preserve tight service guarantees, the decrement of this sum must be
delayed in a special way [1]: this sum can be decremented only after
that its value would decrease also in the ideal system approximated by
QFQ+. For efficiency, QFQ+ keeps track only of the 'instantaneous'
weight sum, increased and decreased immediately as the weight of an
aggregate changes, and as an aggregate is created or destroyed (which,
in its turn, happens as a consequence of some class being
created/destroyed/changed). However, to avoid the problems caused to
service guarantees by these immediate decreases, QFQ+ increments the
system virtual time using the maximum value allowed for the weight
sum, 2^10, in place of the dynamic, instantaneous value. The
instantaneous value of the weight sum is used only to check whether a
request of weight increase or a class creation can be satisfied.
Unfortunately, the problems caused by this choice are worse than the
temporary degradation of the service guarantees that may occur, when a
class is changed or destroyed, if the instantaneous value of the
weight sum was used to update the system virtual time. In fact, the
fraction of the link bandwidth guaranteed by QFQ+ to each aggregate is
equal to the ratio between the weight of the aggregate and the sum of
the weights of the competing aggregates. The packet delay guaranteed
to the aggregate is instead inversely proportional to the guaranteed
bandwidth. By using the maximum possible value, and not the actual
value of the weight sum, QFQ+ provides each aggregate with the worst
possible service guarantees, and not with service guarantees related
to the actual set of competing aggregates. To see the consequences of
this fact, consider the following simple example.
Suppose that only the following aggregates are backlogged, i.e., that
only the classes in the following aggregates have packets to transmit:
one aggregate with weight 10, say A, and ten aggregates with weight 1,
say B1, B2, ..., B10. In particular, suppose that these aggregates are
always backlogged. Given the weight distribution, the smoothest and
fairest service order would be:
A B1 A B2 A B3 A B4 A B5 A B6 A B7 A B8 A B9 A B10 A B1 A B2 ...
QFQ+ would provide exactly this optimal service if it used the actual
value for the weight sum instead of the maximum possible value, i.e.,
11 instead of 2^10. In contrast, since QFQ+ uses the latter value, it
serves aggregates as follows (easy to prove and to reproduce
experimentally):
A B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 A A A A A A A A A A B1 B2 ... B10 A A ...
By replacing 10 with N in the above example, and by increasing N, one
can increase at will the maximum packet delay and the jitter
experienced by the classes in aggregate A.
This patch addresses this issue by just using the above
'instantaneous' value of the weight sum, instead of the maximum
possible value, when updating the system virtual time. After the
instantaneous weight sum is decreased, QFQ+ may deviate from the ideal
service for a time interval in the order of the time to serve one
maximum-size packet for each backlogged class. The worst-case extent
of the deviation exhibited by QFQ+ during this time interval [1] is
basically the same as of the deviation described above (but, without
this patch, QFQ+ suffers from such a deviation all the time). Finally,
this patch modifies the comment to the function qfq_slot_insert, to
make it coherent with the fact that the weight sum used by QFQ+ can
now be lower than the maximum possible value.
[1] P. Valente, "Extending WF2Q+ to support a dynamic traffic mix",
Proceedings of AAA-IDEA'05, June 2005.
Signed-off-by: Paolo Valente <paolo.valente@unimore.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 18 Jul 2013 19:48:40 +0000 (12:48 -0700)]
Merge tag 'driver-core-3.11-rc2' of git://git./linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here are some driver core patches for 3.11-rc2. They aren't really
bugfixes, but a bunch of new helper macros for drivers to properly
create attribute groups, which drivers and subsystems need to fix up a
ton of race issues with incorrectly creating sysfs files (binary and
normal) after userspace has been told that the device is present.
Also here is the ability to create binary files as attribute groups,
to solve that race condition, which was impossible to do before this,
so that's my fault the drivers were broken.
The majority of the .c changes is indenting and moving code around a
bit. It affects no existing code, but allows the large backlog of 70+
patches that I already have created to start flowing into the
different subtrees, instead of having to live in my driver-core tree,
causing merge nightmares in linux-next for the next few months.
These were finalized too late for the -rc1 merge window, which is why
they were didn't make that pull request, testing and review from
others didn't happen until a few weeks ago, and then there's the whole
distraction of the past few days, which prevented these from getting
to you sooner, sorry about that.
Oh, and there's a bugfix for the documentation build warning in here
as well. All of these have been in linux-next this week, with no
reported problems"
* tag 'driver-core-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver-core: fix new kernel-doc warning in base/platform.c
sysfs: use file mode defines from stat.h
sysfs: add more helper macro's for (bin_)attribute(_groups)
driver core: add default groups to struct class
driver core: Introduce device_create_groups
sysfs: prevent warning when only using binary attributes
sysfs: add support for binary attributes in groups
driver core: device.h: add RW and RO attribute macros
sysfs.h: add BIN_ATTR macro
sysfs.h: add ATTRIBUTE_GROUPS() macro
sysfs.h: add __ATTR_RW() macro
Rafael J. Wysocki [Thu, 18 Jul 2013 19:47:00 +0000 (21:47 +0200)]
Merge branch 'pm-fixes'
* pm-fixes:
cpufreq: Revert commit
2f7021a8 to fix CPU hotplug regression
cpufreq: s3c24xx: fix "depends on ARM_S3C24XX" in Kconfig
cpufreq: s3c24xx: rename CONFIG_CPU_FREQ_S3C24XX_DEBUGFS
PM / Sleep: Fix comment typo in pm_wakeup.h
PM / Sleep: avoid 'autosleep' in shutdown progress
cpufreq: Revert commit a66b2e to fix suspend/resume regression
Rafael J. Wysocki [Thu, 18 Jul 2013 19:46:51 +0000 (21:46 +0200)]
Merge branch 'acpi-fixes'
* acpi-fixes:
ACPI / video: ignore BIOS initial backlight value for Fujitsu E753
PNP / ACPI: avoid garbage in resource name
ACPI / memhotplug: Fix a stale pointer in error path
ACPI / scan: Always call acpi_bus_scan() for bus check notifications
ACPI / scan: Do not try to attach scan handlers to devices having them
Lan Tianyu [Tue, 16 Jul 2013 02:07:21 +0000 (10:07 +0800)]
ACPI / video: ignore BIOS initial backlight value for Fujitsu E753
The BIOS of FUjitsu E753 reports an incorrect initial backlight value
for WIN8 compatible OS, causing backlight to be dark during startup.
This change causes the incorrect initial value from BIOS to be ignored.
References: https://bugzilla.kernel.org/show_bug.cgi?id=60161
Reported-and-tested-by: Jan Hinnerk Stosch <janhinnerk.stosch@gmail.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Cc: 3.7+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Thu, 18 Jul 2013 18:32:36 +0000 (11:32 -0700)]
Merge tag 'hwmon-for-linus' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Single patch to staticize a local variable"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (abx500) Staticize abx500_temp_attributes
Linus Torvalds [Thu, 18 Jul 2013 17:50:26 +0000 (10:50 -0700)]
Merge branch 'cpuinit_phase2' of git://git./linux/kernel/git/paulg/linux
Pull phase two of __cpuinit removal from Paul Gortmaker:
"With the __cpuinit infrastructure removed earlier, this group of
commits only removes the function/data tagging that was done with the
various (now no-op) __cpuinit related prefixes.
Now that the dust has settled with yesterday's v3.11-rc1, there
hopefully shouldn't be any new users leaking back in tree, but I think
we can leave the harmless no-op stubs there for a release as a
courtesy to those who still have out of tree stuff and weren't paying
attention.
Although the commits are against the recent tag to allow for minor
context refreshes for things like yesterday's v3.11-rc1~ slab content,
the patches have been largely unchanged for weeks, aside from such
trivial updates.
For detail junkies, the largely boring and mostly irrelevant history
of the patches can be viewed at:
http://git.kernel.org/cgit/linux/kernel/git/paulg/cpuinit-delete.git
If nothing else, I guess it does at least demonstrate the level of
involvement required to shepherd such a treewide change to completion.
This is the same repository of patches that has been applied to the
end of the daily linux-next branches for the past several weeks"
* 'cpuinit_phase2' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (28 commits)
block: delete __cpuinit usage from all block files
drivers: delete __cpuinit usage from all remaining drivers files
kernel: delete __cpuinit usage from all core kernel files
rcu: delete __cpuinit usage from all rcu files
net: delete __cpuinit usage from all net files
acpi: delete __cpuinit usage from all acpi files
hwmon: delete __cpuinit usage from all hwmon files
cpufreq: delete __cpuinit usage from all cpufreq files
clocksource+irqchip: delete __cpuinit usage from all related files
x86: delete __cpuinit usage from all x86 files
score: delete __cpuinit usage from all score files
xtensa: delete __cpuinit usage from all xtensa files
openrisc: delete __cpuinit usage from all openrisc files
m32r: delete __cpuinit usage from all m32r files
hexagon: delete __cpuinit usage from all hexagon files
frv: delete __cpuinit usage from all frv files
cris: delete __cpuinit usage from all cris files
metag: delete __cpuinit usage from all metag files
tile: delete __cpuinit usage from all tile files
sh: delete __cpuinit usage from all sh files
...
Linus Torvalds [Thu, 18 Jul 2013 17:48:48 +0000 (10:48 -0700)]
Merge tag 'sound-3.11' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Except for a slightly big OMAP changes, all rest are small, mostly
boring changes; all either 3.11 regression fixes or stable materials.
- ASoC OMAP fixes due to non-DT OMAP4 removals
- Other ASoC driver changes (sglt5000, wm8978, wm8948, samsung)
- Fix missing locking for snd_pcm_stop() calls in many drivers
- Fix the blocking request_module() in OSS sequencer
- Fix old OSS vwsnd driver builds
- Add a new HD-audio HDMI codec ID"
* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (23 commits)
ALSA: seq-oss: Initialize MIDI clients asynchronously
ALSA: hda - Add new GPU codec ID to snd-hda
staging: line6: Fix unlocked snd_pcm_stop() call
[media] saa7134: Fix unlocked snd_pcm_stop() call
ASoC: s6000: Fix unlocked snd_pcm_stop() call
ASoC: atmel: Fix unlocked snd_pcm_stop() call
ALSA: pxa2xx: Fix unlocked snd_pcm_stop() call
ALSA: usx2y: Fix unlocked snd_pcm_stop() call
ALSA: ua101: Fix unlocked snd_pcm_stop() call
ALSA: 6fire: Fix unlocked snd_pcm_stop() call
ALSA: atiixp: Fix unlocked snd_pcm_stop() call
ALSA: asihpi: Fix unlocked snd_pcm_stop() call
sound: oss/vwsnd: Always define vwsnd_mutex
sound: oss/vwsnd: Add missing inclusion of linux/delay.h
ASoC: wm8978: enable symmetric rates
ASoC: omap-mcbsp: Use different method for DMA request when booted with DT
ASoC: omap-dmic: Do not use platform_get_resource_byname() for DMA
ASoC: omap-mcpdm: Do not use platform_get_resource_byname() for DMA
ASoC: omap-pcm: Request the DMA channel differently when DT is involved
ASoC: Samsung: Set RFS and BFS in slave mode
...
Michael Holzheu [Thu, 18 Jul 2013 10:18:27 +0000 (12:18 +0200)]
s390/kdump: Allow copy_oldmem_page() copy to virtual memory
The kdump mmap patch series (git commit
83086978c63afd7c73e1c) changed the
requirements for copy_oldmem_page(). Now this function is used for copying
to virtual memory.
So implement vmalloc support for the s390 version of copy_oldmem_page().
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Michael Holzheu [Thu, 18 Jul 2013 10:17:57 +0000 (12:17 +0200)]
s390/kdump: Disable mmap for s390
The kdump mmap patch series (git commit
83086978c63afd7c73e1c) directly
map the PT_LOADs to memory. On s390 this does not work because the
copy_from_oldmem() function swaps [0,crashkernel size] with
[crashkernel base, crashkernel base+crashkernel size]. The swap
int copy_from_oldmem() was done in order correctly implement /dev/oldmem.
See: http://marc.info/?l=kexec&m=
136940802511603&w=2
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Wed, 17 Jul 2013 12:26:50 +0000 (14:26 +0200)]
s390/bpf,jit: add pkt_type support
s390 version of
3b58908a "x86: bpf_jit_comp: add pkt_type support".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Heiko Carstens [Tue, 16 Jul 2013 11:25:49 +0000 (13:25 +0200)]
s390/bpf,jit: address randomize and write protect jit code
This is the s390 variant of
314beb9b "x86: bpf_jit_comp: secure bpf
jit against spraying attacks".
With this change the whole jit code and literal pool will be write
protected after creation. In addition the start address of the jit
code won't be always on a page boundary anymore.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Tue, 16 Jul 2013 08:36:06 +0000 (10:36 +0200)]
s390/bpf,jit: use generic jit dumper
This is the s390 backend of
79617801 "filter: bpf_jit_comp: refactor
and unify BPF JIT image dump output".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Tue, 16 Jul 2013 08:24:48 +0000 (10:24 +0200)]
s390/bpf,jit: call module_free() from any context
The workqueue workaround is no longer needed. Same as
5199dfe531
"sparc: bpf_jit_comp: can call module_free() from any context".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Xiao Guangrong [Thu, 18 Jul 2013 04:52:37 +0000 (12:52 +0800)]
KVM: MMU: avoid fast page fault fixing mmio page fault
Currently, fast page fault incorrectly tries to fix mmio page fault when
the generation number is invalid (spte.gen != kvm.gen). It then returns
to guest to retry the fault since it sees the last spte is nonpresent.
This causes an infinite loop.
Since fast page fault only works for direct mmu, the issue exists when
1) tdp is enabled. It is only triggered only on AMD host since on Intel host
the mmio page fault is recognized as ept-misconfig whose handler call
fault-page path with error_code = 0
2) guest paging is disabled. Under this case, the issue is hardly discovered
since paging disable is short-lived and the sptes will be invalid after
memslot changed for 150 times
Fix it by filtering out MMIO page faults in page_fault_can_be_fast.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Dave Airlie [Thu, 18 Jul 2013 10:04:50 +0000 (20:04 +1000)]
Merge branch 'drm/3.11/fixes' of git://linuxtv.org/pinchartl/fbdev into drm-fixes
Fixes builds
* 'drm/3.11/fixes' of git://linuxtv.org/pinchartl/fbdev:
drm/rcar-du: Use the GEM PRIME helpers
drm/shmobile: Use the GEM PRIME helpers
NeilBrown [Wed, 17 Jul 2013 05:19:29 +0000 (15:19 +1000)]
md/raid1: fix bio handling problems in process_checks()
Recent change to use bio_copy_data() in raid1 when repairing
an array is faulty.
The underlying may have changed the bio in various ways using
bio_advance and these need to be undone not just for the 'sbio' which
is being copied to, but also the 'pbio' (primary) which is being
copied from.
So perform the reset on all bios that were read from and do it early.
This also ensure that the sbio->bi_io_vec[j].bv_len passed to
memcmp is correct.
This fixes a crash during a 'check' of a RAID1 array. The crash was
introduced in 3.10 so this is suitable for 3.10-stable.
Cc: stable@vger.kernel.org (3.10)
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown [Wed, 17 Jul 2013 04:55:31 +0000 (14:55 +1000)]
md: Remove recent change which allows devices to skip recovery.
commit
7ceb17e87bde79d285a8b988cfed9eaeebe60b86
md: Allow devices to be re-added to a read-only array.
allowed a bit more than just that. It also allows devices to be added
to a read-write array and to end up skipping recovery.
This patch removes the offending piece of code pending a rewrite for a
subsequent release.
More specifically:
If the array has a bitmap, then the device will still need a bitmap
based resync ('saved_raid_disk' is set under different conditions
is a bitmap is present).
If the array doesn't have a bitmap, then this is correct as long as
nothing has been written to the array since the metadata was checked
by ->validate_super. However there is no locking to ensure that there
was no write.
Bug was introduced in 3.10 and causes data corruption so
patch is suitable for 3.10-stable.
Cc: stable@vger.kernel.org (3.10)
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown [Tue, 16 Jul 2013 06:50:47 +0000 (16:50 +1000)]
md/raid10: fix two problems with RAID10 resync.
1/ When an different between blocks is found, data is copied from
one bio to the other. However bv_len is used as the length to
copy and this could be zero. So use r10_bio->sectors to calculate
length instead.
Using bv_len was probably always a bit dubious, but the introduction
of bio_advance made it much more likely to be a problem.
2/ When preparing some blocks for sync, we don't set BIO_UPTODATE
except on bios that we schedule for a read. This ensures that
missing/failed devices don't confuse the loop at the top of
sync_request write.
Commit
8be185f2c9d54d6 "raid10: Use bio_reset()"
removed a loop which set BIO_UPTDATE on all appropriate bios.
So we need to re-add that flag.
These bugs were introduced in 3.10, so this patch is suitable for
3.10-stable, and can remove a potential for data corruption.
Cc: stable@vger.kernel.org (3.10)
Reported-by: Brassow Jonathan <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Dave Airlie [Thu, 18 Jul 2013 00:19:46 +0000 (10:19 +1000)]
Merge branch 'drm-fixes-3.11' of git://people.freedesktop.org/~agd5f/linux
more DPM fixes for radeon.
* 'drm-fixes-3.11' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/dpm: add debugfs support for RS780/RS880 (v3)
drm/radeon/dpm/atom: fix broken gcc harder
drm/radeon/dpm/atom: restructure logic to work around a compiler bug
drm/radeon/dpm: fix atom vram table parsing
drm/radeon: fix an endian bug in atom table parsing
drm/radeon: add a module parameter to disable aspm
Aaron Lu [Tue, 16 Jul 2013 05:08:05 +0000 (13:08 +0800)]
ACPI / video: no automatic brightness changes by win8-compatible firmware
Starting from win8, MS backlight control driver will set bit 2 of the
parameter of control method _DOS, to inform firmware it should not
perform any automatic brightness changes. This mostly affects hotkey
notification deliver - if we do not set this bit, on hotkey press,
firmware may choose to adjust brightness level instead of sending out
notification and doing nothing.
So this patch sets bit 2 when calling _DOS so that GUIs can show the
notification window on hotkey press. This behavior change is only
necessary for win8 systems.
The MS document on win8 backlight control is here:
http://msdn.microsoft.com/en-US/library/windows/hardware/jj159305
References: https://bugzilla.kernel.org/show_bug.cgi?id=52951
References: https://bugzilla.kernel.org/show_bug.cgi?id=56711
Reported-by: Micael Dias <kam1kaz3@gmail.com>
Reported-by: Dan Garton <dan.garton@gmail.com>
Reported-by: Bob Ziuchkovski <bob.ziuchkovski@gmail.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rafael J. Wysocki [Thu, 18 Jul 2013 00:08:06 +0000 (02:08 +0200)]
ACPI / video / i915: No ACPI backlight if firmware expects Windows 8
According to Matthew Garrett, "Windows 8 leaves backlight control up
to individual graphics drivers rather than making ACPI calls itself.
There's plenty of evidence to suggest that the Intel driver for
Windows [8] doesn't use the ACPI interface, including the fact that
it's broken on a bunch of machines when the OS claims to support
Windows 8. The simplest thing to do appears to be to disable the
ACPI backlight interface on these systems".
There's a problem with that approach, however, because simply
avoiding to register the ACPI backlight interface if the firmware
calls _OSI for Windows 8 may not work in the following situations:
(1) The ACPI backlight interface actually works on the given system
and the i915 driver is not loaded (e.g. another graphics driver
is used).
(2) The ACPI backlight interface doesn't work on the given system,
but there is a vendor platform driver that will register its
own, equally broken, backlight interface if not prevented from
doing so by the ACPI subsystem.
Therefore we need to allow the ACPI backlight interface to be
registered until the i915 driver is loaded which then will unregister
it if the firmware has called _OSI for Windows 8 (or will register
the ACPI video driver without backlight support if not already
present).
For this reason, introduce an alternative function for registering
ACPI video, acpi_video_register_with_quirks(), that will check
whether or not the ACPI video driver has already been registered
and whether or not the backlight Windows 8 quirk has to be applied.
If the quirk has to be applied, it will block the ACPI backlight
support and either unregister the backlight interface if the ACPI
video driver has already been registered, or register the ACPI
video driver without the backlight interface otherwise. Make
the i915 driver use acpi_video_register_with_quirks() instead of
acpi_video_register() in i915_driver_load().
This change is based on earlier patches from Matthew Garrett,
Chun-Yi Lee and Seth Forshee and includes a fix from Aaron Lu's.
References: https://bugzilla.kernel.org/show_bug.cgi?id=51231
Tested-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Tested-by: Yves-Alexis Perez <corsac@debian.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Matthew Garrett <matthew.garrett@nebula.com>
Liu ShuoX [Tue, 16 Jul 2013 08:23:44 +0000 (16:23 +0800)]
PNP / ACPI: avoid garbage in resource name
Set temporary variable as 0 to avoid garbage string output from
/proc/iomem after register resources and reset to PNP dev name
later.
Signed-off-by: Liu ShuoX <shuox.liu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Matthew Garrett [Tue, 16 Jul 2013 17:08:16 +0000 (17:08 +0000)]
ACPI / video: Always call acpi_video_init_brightness() on init
We have to call acpi_video_init_brightness() even if we're not going
to initialise the backlight - Thinkpads seem to use this as the
trigger for enabling ACPI notifications rather than handling it in
firmware.
[rjw: Drop the brightness object created by
acpi_video_init_brightness() if we are not going to use it.]
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Aaron Lu [Tue, 2 Jul 2013 13:59:10 +0000 (21:59 +0800)]
ACPICA: expose OSI version
Expose acpi_gbl_osi_data so that code outside of ACPICA can check
the value of the last successfull _OSI call. The definitions for
OSI versions are moved to actypes.h so that other components can
access them too.
Based on a patch from Matthew Garrett which in turn was based on
an earlier patch from Seth Forshee.
[rjw: Changelog]
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Trond Myklebust [Wed, 17 Jul 2013 20:43:16 +0000 (16:43 -0400)]
NFSv4: Fix a regression against the FreeBSD server
Technically, the Linux client is allowed by the NFSv4 spec to send
3 word bitmaps as part of an OPEN request. However, this causes the
current FreeBSD server to return NFS4ERR_ATTRNOTSUPP errors.
Fix the regression by making the Linux client use a 2 word bitmap unless
doing NFSv4.2 with labeled NFS.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>