Nagabhushana Netagunte [Wed, 9 Nov 2011 21:53:33 +0000 (16:53 -0500)]
da850: add new config file for AM18xx
add new configuration file da850_am18xxevm.h for AM18xx boards
which are based on da850 SOC. AM18xx has WINBOND spi flash which
is indicated in the config file. And make appropriate changes in
board.cfg for building.
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Alexander Holler [Wed, 9 Nov 2011 21:40:11 +0000 (16:40 -0500)]
BeagleBoard: config: Switch to ttyO2
This is needed to support the latest kernel versions.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Tom Rini [Wed, 9 Nov 2011 21:40:08 +0000 (16:40 -0500)]
OMAP3: Change omap3_evm maintainer
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Tom Rini [Wed, 9 Nov 2011 21:40:04 +0000 (16:40 -0500)]
devkit8000: Fix NAND SPL on boards with 256MB NAND
The devkit8000 ships with either a 128MB or 256MB NAND chip. In
order for SPL to work with 256MB NAND CONFIG_SYS_NAND_5_ADDR_CYCLE
needs to be set. After talking with Scott Wood this should be
safe to set even for smaller NAND chips.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Frederik Kriewitz <frederik@kriewitz.eu>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Linus Walleij [Wed, 9 Nov 2011 06:16:37 +0000 (06:16 +0000)]
integrator: enable Vpp and disable flash protection
This enables Vpp and disables the flash protection on the
Integrator when starting U-Boot. The integrator/AP has double
protection mechanisms: this one and the EBI protection bit
(patch earlier), the Integrator/CP has only one line of
protection in these registers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Wed, 9 Nov 2011 06:16:17 +0000 (06:16 +0000)]
integrator: add system controller header
Break out the AP system controller and CP "CP controller"
registers into a header file, it gives better overview than
hardcoding its values and other disturbing practices.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Wed, 9 Nov 2011 06:15:59 +0000 (06:15 +0000)]
integrator: make flash writeable on boot
This reconfigures the EBI (External Bus Interface) on the
integrator so that chip select 1, handling the flash memory, is
set to writeable. Without this it is not possible for U-Boot to
access flash memory and it crashes on startup since CFI won't
work properly.
Since this is the first time we use the EBI, we create a header
file for its registers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Wed, 9 Nov 2011 06:14:40 +0000 (06:14 +0000)]
integrator: use io-accessors for board init
Casting around to *(volatile ulong *) doesn't look good, so include
the <asm/io.h> macros and use good old readl() instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Wed, 9 Nov 2011 06:14:20 +0000 (06:14 +0000)]
integrator: move text offset to config
Do away with the config.mk file and move the text offset to the
config files to make things easier.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Wed, 9 Nov 2011 06:14:05 +0000 (06:14 +0000)]
integrator: pass configs for core modules
Alter the board.cfg to pass core module configuration flags
so we can make compile-time switches for different core
modules. These are already in use for some low-level code,
they just got lost in the conversion to the new build
system.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Macpaul Lin [Tue, 19 Oct 2010 09:10:34 +0000 (17:10 +0800)]
adp-ag101p: add product into MAINTAINERS list
Add ADP-AG101P into MAINTAINERS list.
Add ADP-AG101P into boards.cfg.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Macpaul Lin [Tue, 19 Oct 2010 09:05:51 +0000 (17:05 +0800)]
adp-ag101p: Add SoC and board support of ag101p
Add softcore SoC ag101p and the board adp-ag101p support.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Kumar Gala [Wed, 9 Nov 2011 15:10:49 +0000 (09:10 -0600)]
powerpc/85xx: Fix NAND SPL support
We cause CCSRBAR to be relocated in the SPL phase of NAND boot which
isn't expected and breaks things. Fixing the board config.h to NOT
relocate CCSR during the CONFIG_NAND_SPL phase.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Macpaul Lin [Wed, 9 Nov 2011 08:24:57 +0000 (16:24 +0800)]
nds32: fix data section of linker script
Make linker script handles .data.rel sections.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Tested-by: Macpaul Lin <macpaul@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Macpaul Lin [Mon, 26 Sep 2011 09:44:34 +0000 (17:44 +0800)]
dwcddr21mctl: Synopsys DWC DDR2/1 Memory Controller
Header definitions of Synopsys DWC DDR2/1 Memory Controller.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Macpaul Lin [Tue, 27 Sep 2011 07:31:07 +0000 (15:31 +0800)]
andes_pcu.h: header file of andes_pcu power control unit
header file of andes_pcu power control unit
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Kumar Gala [Tue, 8 Nov 2011 03:39:43 +0000 (03:39 +0000)]
fsl_i2c: Fix compile warning
fsl_i2c.c: In function 'i2c_init':
fsl_i2c.c:245:7: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
David Müller (ELSOFT AG) [Mon, 31 Oct 2011 01:22:07 +0000 (01:22 +0000)]
ARM: remove superfluous setting of arch_number in board specific code.
Signed-off-by: David Mueller <d.mueller@elsoft.ch>
Marek Vasut [Mon, 24 Oct 2011 00:14:23 +0000 (00:14 +0000)]
SPL: Allow ARM926EJS to avoid compiling in the CPU support code
This allows the SPL to avoid compiling in the CPU support code.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Linus Walleij [Sun, 23 Oct 2011 21:02:03 +0000 (21:02 +0000)]
integrator: do not test first part of the memory
When booting from Flash, the Integrator remaps its flash memory
from 0x24000000 to 0x00000000, and starts executing it at
0x00000000. This ROM thus hides the RAM underneath and first
0x40000 bytes of the memory cannot be tested by get_ram_size().
So let's test from 0x40000 to the end of detected memory
instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Jon Medhurst (Tixy) [Fri, 4 Nov 2011 03:06:12 +0000 (03:06 +0000)]
MMC: PL180: Fix infinite loop with VExpress extended fifo implementation
The new IO FPGA implementation for Versatile Express contains an MMCI
(PL180) cell with the FIFO extended to 128 words. This causes the
read_bytes() function to go into an infinite loop; as it will wait for
for the half-full signal (SDI_STA_RXFIFOBR) if there are more than 8
words remaining (SDI_FIFO_BURST_SIZE), but it won't receive this signal
once there are fewer than 64 words left to transfer.
One possible fix is to add some build time configuration to change
SDI_FIFO_BURST_SIZE for the new implementation. However, the problematic
code only seems to exist as a small performance optimisation, so the
solution implemented by this patch is to simply remove it. The error
checking following the loop is also removed as this will be handled by
code further down the function.
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Jon Medhurst <jon.medhurst@linaro.org>
Po-Yu Chuang [Wed, 10 Aug 2011 17:44:21 +0000 (17:44 +0000)]
arm: a320: fix broken timer
timer.c used static data and are called before relocation.
Move all static variables into global_data structure. Also cleanup
timer.c from unused stubs and make it truly use 64 bit tick values.
Remove reset_timer_masked() get_timer_masked()
reference: arch/arm/cpu/arm926ejs/at91/timer.c
Based on Reinhard Meyer <u-boot@emk-elektronik.de>'s patches
5dca710a3d7703e41da0e9894f2d71f9e25bea6b
cfff263f41e32c7ba2ee9162a8cc6423eb5a8390
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Tested-by: Macpaul Lin <macpaul@gmail.com>
Asen Dimov [Mon, 31 Oct 2011 08:54:20 +0000 (08:54 +0000)]
ARM: define CONFIG_MACH_TYPE for all ronetix boards
Signed-off-by: Asen Chavdarov Dimov <dimov@ronetix.at>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Kumar Gala [Tue, 8 Nov 2011 17:03:54 +0000 (11:03 -0600)]
powerpc/85xx: Fix MPC8572DS NAND build
Reduce NAND SPL build size by not include TLB entries that arent used by
it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Poonam Aggrwal [Tue, 1 Nov 2011 13:28:20 +0000 (18:58 +0530)]
fsl_ifc: Fixed a bug in the erratum handling code for IFC_A003399
Wrong pointer was being used to copy code into L2SRAM.
Also removed the unreferenced variable l2srbar.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 1 Nov 2011 03:13:26 +0000 (22:13 -0500)]
powerpc/85xx: Add support for Book-E MMU Arch v2.0
A few of the config registers changed definition between MMU v1.0 and
MMUv2.0. The new e6500 core from Freescale implements v2.0 of the
architecture.
Specifically, how we determine the size of TLB entries we support in the
variable size (or TLBCAM/TLB1) array is specified in a new register
(TLBnPS - TLB n Page size) instead of via TLBnCFG.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Ramneek Mehresh [Tue, 8 Nov 2011 04:51:28 +0000 (10:21 +0530)]
powerpc/85xx: Make inclusion of USB device fixup conditional
Include call to usb device-fixup only when CONFIG_HAS_FSL_DR_USB is
defined for the platform - P1020RDB, P1010RDB, P1020-PC
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Ramneek Mehresh [Tue, 8 Nov 2011 07:39:20 +0000 (13:09 +0530)]
powerpc/85xx: Fix warning for USB device-fixup
Fix USB device-fixup warning "node not found". This was occuring
because of static nature of start_offset variable
Static start_offset was storing offset of last node modified, and
was becoming issue if node fixup is carried multiple times,
resulting in "node not found" warning
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Mon, 31 Oct 2011 18:30:45 +0000 (13:30 -0500)]
powerpc/85xx: resize the boot page TLB before relocating CCSR
On some Freescale systems (e.g. those booted from the on-chip ROM), the
TLB that covers the boot page can also cover CCSR, which breaks the CCSR
relocation code. To fix this, we resize the boot page TLB so that it only
covers the 4KB boot page.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Mon, 31 Oct 2011 18:30:44 +0000 (13:30 -0500)]
powerpc/85xx: verify the current address of CCSR before relocating it
Verify that CCSR is actually located where it is supposed to be before
we relocate it. This is useful in detecting U-Boot configurations that
are broken (e.g. an incorrect value for CONFIG_SYS_CCSRBAR_DEFAULT).
If the current value is wrong, we enter an infinite loop, which is handy
for debuggers.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Mon, 31 Oct 2011 18:30:43 +0000 (13:30 -0500)]
powerpc/85xx: add some missing sync instructions in the CCSR relocation code
Calls to tlbwe and tlbsx should be preceded with an isync/msync pair.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Mon, 31 Oct 2011 18:30:42 +0000 (13:30 -0500)]
powerpc/85xx: fix some comments in the CCSR relocation code
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Mon, 31 Oct 2011 18:30:41 +0000 (13:30 -0500)]
powerpc/85xx: fix definition of MAS register macros
Some of the MAS register macros do not protect the parameter with
parentheses, which could cause wrong values if the parameter includes
operators.
Also fix the definition of TSIZE_TO_BYTES() so that it actually uses
the parameter. This hasn't caused any problems to date because the
parameter was always been 'tsize'.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
chenhui zhao [Tue, 6 Sep 2011 16:41:18 +0000 (16:41 +0000)]
powerpc/mpc8548cds: Fix network initialization
Add board_eth_init(). PCIe network card is also supported.
Put RGMII init after tsec_eth_init().
Skip initializing eTSEC3 and eTSEC4 with Carrier boards prior to ver 1.3.
Signed-off-by: Ebony Zhu
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
chenhui zhao [Mon, 3 Oct 2011 13:38:50 +0000 (08:38 -0500)]
powerpc/mpc8548: Add workaround for erratum NMG_eTSEC129
Erratum NMG_eTSEC129 (eTSEC86 in MPC8548 document) applies to some early
verion silicons. This workaround detects if the eTSEC Rx logic is properly
initialized, and reinitialize the eTSEC Rx logic.
Signed-off-by: Gong Chen <g.chen@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Roy Zang [Fri, 28 Oct 2011 05:15:36 +0000 (13:15 +0800)]
powerpc/QorIQ: fix network frame manager TBI PHY address settings
TBI PHY address (TBIPA) register has been set in general frame manager
phy init funciton dtsec_init_phy() in drivers/net/fm/eth.c
So remove the duplicate code on QorIQ frame manager Ethernet related
platforms, which include Hydra board, P4080DS board and P2041rdb board.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Manjunath Hadli [Tue, 8 Nov 2011 13:59:57 +0000 (08:59 -0500)]
dm646x: pass board revision info to kernel
add a function in board file to pass board revision
info to kernel. Revision number 0 and 1 are passed in
case of DM6467 and DM6467T respectively.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Manjunath Hadli [Tue, 8 Nov 2011 13:59:54 +0000 (08:59 -0500)]
dm646x: add new configuration for dm6467T
add new configuration file for dm6467T and appropraite changes
in boards.cfg. dm6467T is the new varaiant of dm6467 SOC which
supports 33 MHz reference clock where as dm6467 supports 27 MHz
reference clock.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Christian Riesch [Tue, 8 Nov 2011 13:55:13 +0000 (08:55 -0500)]
arm, davinci: Fix setting of the SDRAM configuration register
da850_ddr_setup() expects the BOOTUNLOCK bit to be set in
If BOOTUNLOCK is not set in this define, several configuration
bits will not be writeable and the code will not work.
Since the BOOTUNLOCK and TIMUNLOCK bits are not configuration options
but access control bits, this patch changes the code to work
irrespective of the value of these bits in CONFIG_SYS_DA850_DDR2_SDBCR.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Heiko Schocher <hs@denx.de>
Cc: Paulraj Sandeep <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Christian Riesch [Tue, 8 Nov 2011 13:55:10 +0000 (08:55 -0500)]
arm, davinci: Remove the duplication of LPSC functions
The LPSC functions defined in
arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c
are replaced by those already defined in
arch/arm/cpu/arm926ejs/davinci/psc.c.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Heiko Schocher <hs@denx.de>
Cc: Paulraj Sandeep <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Christian Riesch [Tue, 8 Nov 2011 13:55:07 +0000 (08:55 -0500)]
arm, davinci: Rename AM1808 lowlevel functions to DA850
Rename arch/arm/cpu/arm926ejs/davinci/am1808_lowlevel.c and
arch/arm/include/asm/arch-davinci/am1808_lowlevel.h to da850_lowlevel.c
and da850_lowlevel.h since they apply not only to the AM1808 SoC
but to all DA850 chips. The function names and #defines are changed
likewise.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Heiko Schocher <hs@denx.de>
Cc: Paulraj Sandeep <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Prabhakar Lad [Tue, 8 Nov 2011 13:55:03 +0000 (08:55 -0500)]
da8xxevm: fix build error
This patch fixes following compile error for da8xx evm
da830evm.c: In function 'board_init':
da830evm.c:222: error: 'DAVINCI_SYSCFG_SUSPSRC_UART2' undeclared (first use in this function)
da830evm.c:222: error: (Each undeclared identifier is reported only once
da830evm.c:222: error: for each function it appears in.)
make[2]: *** [da830evm.o] Error 1
similarly for da850evm.
introduced through commit:
f9fc237f1f07d4e5ff7c9c2da39cabc8d3d7b339
Signed-off-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Wolfgang Denk [Sun, 6 Nov 2011 21:49:44 +0000 (22:49 +0100)]
env: allow to export only selected variables
New syntax:
env export [-t | -b | -c] [-s size] addr [var ...]
With this change it is possible to provide a list of variables names
that shall be exported. Whenno arguments are given, the whole
environment gets exported.
NOTE: The new handling of the "size" argument means a change to the
user API.
Signed-off-by: Wolfgang Denk <wd@denx.de>
David Müller (ELSOFT AG) [Mon, 31 Oct 2011 01:22:06 +0000 (01:22 +0000)]
ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE
Signed-off-by: David Mueller <d.mueller@elsoft.ch>
Wolfgang Denk [Tue, 8 Nov 2011 06:44:52 +0000 (07:44 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx
* 'master' of git://git.denx.de/u-boot-mpc83xx:
powerpc/mpc83xx: Add 33.33MHz support for mpc8360emds
powerpc/mpc83xx: Add 512MB DDR support for mpc8360emds
mpc83xx: Rename CONFIG_SYS_DDR_CONFIG and cleanup DDR csbnds code
mpc83xx: Cleanup usage of LBC constants
mpc83xx: Cleanup usage of DDR constants
mpc83xx: Cleanup usage of BAT constants
mpc83xx: cosmetic: vme8349.h checkpatch compliance
mpc83xx: cosmetic: ve8313.h checkpatch compliance
mpc83xx: cosmetic: sbc8349.h checkpatch compliance
mpc83xx: cosmetic: mpc8308_p1m.h checkpatch compliance
mpc83xx: cosmetic: kmeter1.h checkpatch compliance
mpc83xx: cosmetic: TQM834x.h checkpatch compliance
mpc83xx: cosmetic: SIMPC8313.h checkpatch compliance
mpc83xx: cosmetic: MVBLM7.h checkpatch compliance
mpc83xx: cosmetic: MPC837XERDB.h checkpatch compliance
mpc83xx: cosmetic: MPC837XEMDS.h checkpatch compliance
mpc83xx: cosmetic: MPC8360ERDK.h checkpatch compliance
mpc83xx: cosmetic: MPC8360EMDS.h checkpatch compliance
mpc83xx: cosmetic: MPC8349ITX.h checkpatch compliance
mpc83xx: cosmetic: MPC8349EMDS.h checkpatch compliance
mpc83xx: cosmetic: MPC832XEMDS.h checkpatch compliance
mpc83xx: cosmetic: MPC8323ERDB.h checkpatch compliance
mpc83xx: cosmetic: MPC8315ERDB.h checkpatch compliance
mpc83xx: cosmetic: MPC8313ERDB.h checkpatch compliance
mpc83xx: cosmetic: MPC8308RDB.h checkpatch compliance
mpc83xx: cosmetic: MERGERBOX.h checkpatch compliance
mpc83xx: Fix ipic structure definition
powerpc, mpc83xx: add DDR SDRAM Timing Configuration 3 definitions
cosmetic, powerpc, mpc83xx: checkpatch cleanup
powerpc/83xx: move km 83xx specific i2c code to km83xx_i2c
mpc83xx: fix global timer structure definition
Jerry Huang [Mon, 7 Nov 2011 05:20:21 +0000 (13:20 +0800)]
powerpc/mpc83xx: Add 33.33MHz support for mpc8360emds
The new MPC8360EMDS board changes the oscillator to 33.33MHz
in order to support QE 500MHz since 2008.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Wolfgang Denk [Mon, 7 Nov 2011 23:38:52 +0000 (00:38 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
Arm: re-introduce the MACH_TYPE_XXXXXX for EB_CPUX9K2 board
arm: jadecpu: Readd MACH_TYPE_JADECPU
at91: defined mach-types for otc570 board in board config file
at91: defined mach-types for meesc board in board config file
mx31pdk: Enable D and I caches
ehci-mxc: remove incorrect comment
README: Fix supported i.MX SoC list for CONFIG_MXC_SPI
mx53: Turn off child clocks before reconfigure perclk_root
qong: enable support for compressed images
imx: imx31_phycore.h: fix checkpatch warnings
vision2: Remove unused get_board_rev function
mx53smd: Remove unused get_board_rev function
mx53ard: Remove unused get_board_rev function
mx53evk: Remove unused get_board_rev function
mx53evk: Add RTC support
mx53loco: Remove unused get_board_rev function
mx53evk: Remove unneeded '1' from mx53evk.h
OMAP3: mvblx: Initial support for mvBlueLYNX-X
ARM: dig297: Define MACH_TYPE_OMAP3_CPS and CONFIG_MACH_TYPE
omap3: mem: Move comments next to definitions
omap3: mem: Clean-up whitespaces
omap3: mem: Define and use common macros
Davinci: ea20: added PREBOOT to configuration
Davinci: ea20: added I2C support
Davinci: ea20: added video support
VIDEO: davinci: add framebuffer to da8xx
ARM: Davinci: added missing registers to hardware.h
Davinci: ea20: add gpios for LCD backlight control
Davinci: ea20: add gpio for keeping power on in board_late_init
Davinci: ea20: Add default U-Boot environment
Davinci: ea20: Add early init to get early output from console
Davinci: ea20: Add NAND support
Davinci: ea20: set GPIOs to hold MII-Phy in reset and set UART0-Switch for console
Davinci: ea20: set console on UART0
arm, davinci: add cam_enc_4xx support
arm926ejs, davinci: add missing spi defines for dm365
arm926ejs, davinci: add cpuinfo for dm365
arm, davinci: add lowlevel function for dm365 soc
arm, davinci: add header files for dm365
spl, nand: add 4bit HW ecc oob first nand_read_page function
arm, davinci: add support for new spl framework
spl: add option for adding post memory test to the SPL framework
net, davinci_emac: make clock divider in MDIO control register configurable
arm, usb, davinci: make USBPHY_CTL register configurable
usb, davinci: add enable_vbus() weak function
omap3evm: fix errors caused by multiple definitions
omap3evm: Add (quick) configuration for NAND only
omap3evm: Add (quick) configuration for MMC/SD only
omap3evm: move common config options to new file
omap3evm: Prepare to split configuration
omap3evm: Reorder related config options
omap/spl: actually enable the console
davinci_emac: compilation fix, phy is array now
omap3evm: Set environment variable 'ethaddr'
arm, arm926: fix missing symbols in NAND_SPL mode
arm, davinci: Add function lpsc_syncreset()
arm, davinci: replace CONFIG_PRELOADER with CONFIG_SPL_BUILD
arm/km: portl2 environment address update to P1B
arm/km: adapt bootcounter evaluation
arm/km: enable jffs2 cmds
arm/km: trigger reconfiguration for the Xilinx FPGA
arm/km: add boardid and hwkey to kernel command line
ARM: Reintroduce MACH_TYPE_KM_KIRKWOOD for keymile ARM boards
netspace_v2: enable I2C EEPROM support
netspace_v2: fix SDRAM configuration
armada100: define CONFIG_SYS_CACHELINE_SIZE
pantheon: define CONFIG_SYS_CACHELINE_SIZE
kirkwood: define CONFIG_SYS_CACHELINE_SIZE
kirkwood: drop empty asm-offsets.s file
arm/km/mgcoge3un: enhance "waitforne" feature
arm/km: add variable waitforne to mgcoge3un
gplugD: Fix for error:MACH_TYPE_SHEEVAD undeclared
ARM: dreamplug: fix compilation
ARM: DockStar: fix compilation
ARM: netspace_v2: fix warnings
am335x: Drop board_sysinfo struct
am335x: Temporarily add MACH_TYPE define
misc:pmic:samsung Enable PMIC driver at C210 Universal target
dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p UNIVERSAL C210 target
dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p GONI target
smdkv310: use macro for mmc data read function address
smdkv310: use spl framework for mmc spl
SMDKV310: use get_ram_size() to validate dram size
SMDKV310: Initialize board id using CONFIG_MACH_TYPE
ORIGEN : use absolute paths and fix tool naming
ORIGEN : enable device tree support
MX25: tx25: Fix building due to missing MACH_TYPE
mx31: Add board support for HALE TT-01
mx31: add ESD control registers
mx31: define pins and init for UART2 and CSPI3
MX35: add support for flea3 board
MX51: vision2: add MACH_TYPE in config file
vision2: Remove unused header file
mx51evk: Remove unused get_board_rev function
mx51evk: Remove unneeded '1' from mx51evk.h
I2C: Fix mxc_i2c.c problem on imx31_phycore
mx35pdk: Add RTC support
mx51evk: Use GPIO API for configuring the IOMUX
mx51evk: Add RTC support
rtc: Make mc13783-rtc driver generic
qong: remove unneeded IOMUX settings
qong: Use mx31_set_gpr to setup USBH2 pins
mx31: Introduce mx31_set_gpr function
mx31pdk: Add MC13783 PMIC support
qong: remove unneeded "1" from qong.h
misc: pmic: fix regression in pmic_fsl.c (SPI)
mx5 configs: CONFIG_PRIME should really be CONFIG_ETHPRIME
MX35: Drop unnecessary prototypes from imx-regs.h
I2C: added I2C-2 and I2C-3 to MX35
MX35: factorize common assembly code
MX35: add reset cause as provided by other i.MX
MX35: add pins definition for UART3
MX35: added ESDC structure to imx-regs
Wolfgang Denk [Mon, 7 Nov 2011 23:37:27 +0000 (00:37 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-coldfire
* 'master' of git://git.denx.de/u-boot-coldfire:
ColdFire: The EB+MCF-EV123 boards config update
ColdFire: Fix the compile issue for M52277
ColdFire:Moving the remaining coldfire boards to boards.cfg
Wolfgang Denk [Mon, 7 Nov 2011 23:34:07 +0000 (00:34 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-i2c
* 'master' of git://git.denx.de/u-boot-i2c:
Powerpc/i2c: Use the same initialize codes
Wolfgang Denk [Sat, 5 Nov 2011 05:13:19 +0000 (05:13 +0000)]
board/siemens/SCM/scm.c: Fix GCC 4.6 build warning
Fix:
scm.c: In function 'config_scoh_cs':
scm.c:400:16: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 5 Nov 2011 05:13:18 +0000 (05:13 +0000)]
board/funkwerk/vovpn-gw/vovpn-gw.c: Fix GCC 4.6 build warning
Fix:
vovpn-gw.c: In function 'misc_init_r':
vovpn-gw.c:266:16: warning: variable 'temp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 5 Nov 2011 05:13:17 +0000 (05:13 +0000)]
board/freescale/mpc8266ads/mpc8266ads.c: Fix GCC 4.6 build warning
Fix:
mpc8266ads.c: In function 'initdram':
mpc8266ads.c:278:9: warning: variable 'spd_size' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 5 Nov 2011 05:13:16 +0000 (05:13 +0000)]
board/freescale/mpc8266ads/mpc8266ads.c: CodingStyle cleanup
Make (mostly) checkpatch clean.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Rune Torgersen <runet@innovsys.com>
Wolfgang Denk [Sat, 5 Nov 2011 05:13:15 +0000 (05:13 +0000)]
board/sacsng/sacsng.c: Fix GCC 4.6 build warning
Fix:
sacsng.c: In function 'initdram':
sacsng.c:180:9: warning: variable 'spd_size' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Jerry Van Baren <gerald.vanbaren@smiths-aerospace.com>
Wolfgang Denk [Sat, 5 Nov 2011 05:13:14 +0000 (05:13 +0000)]
board/sacsng/sacsng.c: CodingStyle cleanup
Make (mostly) checkpatch clean.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Jerry Van Baren <gerald.vanbaren@smiths-aerospace.com>
Wolfgang Denk [Sat, 5 Nov 2011 05:13:13 +0000 (05:13 +0000)]
board/rpxsuper/flash.c: Fix GCC 4.6 build warning
Fix:
flash.c: In function 'flash_init':
flash.c:52:19: warning: variable 'size' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 5 Nov 2011 05:13:12 +0000 (05:13 +0000)]
board/rpxsuper/flash.c: minimal CodingStyle cleanup
Really minimal and local, just good enough to make checkpatch not
complain about the changes in the following commit.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 5 Nov 2011 05:13:11 +0000 (05:13 +0000)]
board/ids8247/ids8247.c: Fix GCC 4.6 build warning
Fix:
ids8247.c: In function 'initdram':
ids8247.c:284:14: warning: variable 'lsize' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Wolfgang Denk [Sat, 5 Nov 2011 05:13:10 +0000 (05:13 +0000)]
board/hymod/input.c: Fix GCC 4.6 build warning
Fix:
input.c: In function 'hymod_get_ethaddr':
input.c:79:10: warning: variable 'ea' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Murray Jensen <Murray.Jensen@csiro.au>
Wolfgang Denk [Sat, 5 Nov 2011 05:13:09 +0000 (05:13 +0000)]
board/ep82xxm/ep82xxm.c: Fix GCC 4.6 build warning
Fix:
ep82xxm.c: In function 'initdram':
ep82xxm.c:233:16: warning: variable 'ramtmp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 5 Nov 2011 05:13:08 +0000 (05:13 +0000)]
board/gw8260/flash.c: Fix GCC 4.6 build warning
Fix:
flash.c: In function 'flash_init':
flash.c:81:16: warning: variable 'size' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Oliver Brown <obrown@adventnetworks.com>
Wolfgang Denk [Sat, 5 Nov 2011 05:13:07 +0000 (05:13 +0000)]
board/gw8260/flash.c: minimal CodingStyle cleanup
Really minimal and local, just good enough to make checkpatch not
complain about the changes in the following commit.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Oliver Brown <obrown@adventnetworks.com>
Wolfgang Denk [Sat, 5 Nov 2011 05:13:06 +0000 (05:13 +0000)]
board/cogent/flash.c: Fix GCC 4.6 buiild warning
Fix:
flash.c: In function 'flash_init':
flash.c:295:16: warning: variable 'fip' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Murray Jensen <Murray.Jensen@csiro.au>
Wolfgang Denk [Sat, 5 Nov 2011 05:13:05 +0000 (05:13 +0000)]
arch/powerpc/cpu/mpc8260/spi.c: Fix GCC 4.6 build warnings
Fix:
spi.c: In function 'spi_init_r':
spi.c:279:22: warning: variable 'cp' set but not used
[-Wunused-but-set-variable]
spi.c: In function 'spi_xfer':
spi.c:361:22: warning: variable 'cp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 5 Nov 2011 05:13:04 +0000 (05:13 +0000)]
common/cmd_flash.c: Fix GCC 4.6 build warnings
Fix:
cmd_flash.c:355:32: warning: 'info' may be used uninitialized in this
function [-Wuninitialized]
cmd_flash.c:354:10: warning: 'sect_first' may be used uninitialized in
this function [-Wuninitialized]
cmd_flash.c:354:10: warning: 'sect_last' may be used uninitialized in
this function [-Wuninitialized]
cmd_flash.c: In function 'do_protect':
cmd_flash.c:540:9: warning: 'info' may be used uninitialized in this
function [-Wuninitialized]
cmd_flash.c:538:9: warning: 'sect_first' may be used uninitialized in
this function [-Wuninitialized]
cmd_flash.c:538:9: warning: 'sect_last' may be used uninitialized in
this function [-Wuninitialized]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 5 Nov 2011 05:13:03 +0000 (05:13 +0000)]
drivers/net/rtl8139.c: Fix GCC 4.6 build warnings
Fix:
rtl8139.c: In function 'rtl8139_probe':
rtl8139.c:256:15: warning: variable 'fullduplex' set but not used
[-Wunused-but-set-variable]
rtl8139.c:256:6: warning: variable 'speed10' set but not used
[-Wunused-but-set-variable]
rtl8139.c: In function 'rtl_transmit':
rtl8139.c:419:16: warning: variable 'txstatus' set but not used
[-Wunused-but-set-variable]
Change code to use new debug macros; also fix the new errors and
warnigns popping up now, like "error: 'to' undeclared" and some
"warning: format '%X' expects argument of type 'unsigned int', but
argument X has type 'long unsigned int'"
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Mon, 7 Nov 2011 21:43:37 +0000 (22:43 +0100)]
board/linkstation/ide.c: Fix GCC 4.6 build warnings
Fix:
ide.c: In function 'ide_preinit':
ide.c:69:21: warning: array subscript is above array bounds
[-Warray-bounds]
ide.c:69:21: warning: array subscript is above array bounds
[-Warray-bounds]
ide.c:70:17: warning: array subscript is above array bounds
[-Warray-bounds]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Wolfgang Denk [Sat, 5 Nov 2011 05:13:01 +0000 (05:13 +0000)]
drivers/net/rtl8169.c: Fix GCC 4.6 build warning
Fix:
rtl8169.c: In function 'rtl_init':
rtl8169.c:742:13: warning: variable 'printed_version' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 5 Nov 2011 05:13:00 +0000 (05:13 +0000)]
board/mousse/flash.c: Fix GCC 4.6 buil warnings
Fix:
flash.c: In function 'flash_erase':
flash.c:780:18: warning: variable 'l_sect' set but not used
[-Wunused-but-set-variable]
flash.c:779:11: warning: variable 'addr' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 5 Nov 2011 05:12:59 +0000 (05:12 +0000)]
board/etin/kvme080/multiverse.c: Fix GCC 4.6 build warning.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Sangmoon Kim <dogoil@etinsys.com>
Wolfgang Denk [Sat, 5 Nov 2011 05:12:58 +0000 (05:12 +0000)]
drivers/net/pcnet.c: Change debug code to fix build warning
Fix:
pcnet.c: In function 'pcnet_probe':
pcnet.c:247:8: warning: variable 'chipname' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:56:00 +0000 (15:56 +0000)]
board/alaska/flash.c: Fix GCC 4.6 build warnings
Fix:
flash.c: In function 'flash_erase':
flash.c:409:21: warning: variable 'last' set but not used
[-Wunused-but-set-variable]
flash.c:408:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'write_data':
flash.c:669:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'write_data_block':
flash.c:709:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:59 +0000 (15:55 +0000)]
arch/powerpc/lib/bat_rw.c: Fix GCC 4.6 build warning
Fix:
bat_rw.c: In function 'write_bat':
bat_rw.c:38:6: warning: variable 'batn' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andy Fleming <afleming@gmail.com>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:58 +0000 (15:55 +0000)]
mpc8220/i2c.c: Fix GCC 4.6 build warning
Fix:
i2c.c: In function 'wait_for_bb':
i2c.c:109:16: warning: variable 'temp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:57 +0000 (15:55 +0000)]
mpc8260/i2c.c: replace PRINTD() by debug()
This also fixes some GCC 4.6 build warnings like:
i2c.c: In function 'i2c_init':
i2c.c:221:26: warning: variable 'txbd' set but not used
[-Wunused-but-set-variable]
i2c.c:221:19: warning: variable 'rxbd' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:56 +0000 (15:55 +0000)]
mpc8260/i2c.c: CodingStyle cleanup
Make (mostly) checkpatch clean (don't convert to use I/O accessors
yet, so there will be "Use of volatile is usually wrong" warnings
left. Also accept some other harmless checkpatch warnings.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:55 +0000 (15:55 +0000)]
mpc8220/fec.c: Fix GCC 4.6 build warning
Fix:
fec.c: In function 'mpc8220_fec_recv':
fec.c:733:8: warning: variable 'frame' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:54 +0000 (15:55 +0000)]
common/cmd_i2c.c: Fix GCC 4.6 build warning
Fix:
cmd_i2c.c: In function 'do_i2c_add_bus':
cmd_i2c.c:1212:19: warning: variable 'dev' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:53 +0000 (15:55 +0000)]
board/tqc/tqm8272/tqm8272.c: Fix GCC 4.6 build warning:
Fix:
tqm8272.c: In function 'initdram':
tqm8272.c:462:14: warning: variable 'lsize' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:52 +0000 (15:55 +0000)]
mpc8260/speed.c: Fix GCC 4.6 build warnings
Fix:
speed.c: In function 'get_clocks':
speed.c:113:30: warning: variable 'cpmdf' set but not used
[-Wunused-but-set-variable]
speed.c:113:23: warning: variable 'busdf' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:51 +0000 (15:55 +0000)]
TQM850M: Add missing CONFIG_BOOTDELAY
This also fixes a build warning:
main.c: In function 'main_loop':
main.c:311:16: warning: variable 'bootlimit' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:50 +0000 (15:55 +0000)]
board/svm_sc8xx/flash.c: Fix GCC 4.6 build warning
Fix:
flash.c: In function 'write_word':
flash.c:542:15: warning: variable 'last' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:49 +0000 (15:55 +0000)]
board/svm_sc8xx/flash.c: CodingStyle cleanup
Make (mostly) checkpatch clean (don't convert to use I/O accessors
yet, so there will be "Use of volatile is usually wrong" warnings
left.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:48 +0000 (15:55 +0000)]
board/svm_sc8xx/svm_sc8xx.c: Fix GCC 4.6 build warning
Fix:
svm_sc8xx.c: In function 'checkboard':
svm_sc8xx.c:83:6: warning: variable 'board_type' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:47 +0000 (15:55 +0000)]
board/rbc823/flash.c: Fix flash initalization
The RBC823 has only one NOR flash bank. Remove all code trying to
deal with a second bank. This also fixes a number of GCC 4.6 build
warnings:
flash.c: In function 'flash_init':
flash.c:62:12: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:63:12: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:66:12: warning: array subscript is above array bounds
[-Warray-bounds]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:46 +0000 (15:55 +0000)]
board/rbc823/flash.c: CodingStyle cleanup
Make (mostly) checkpatch clean (don't convert to use I/O accessors
yet, so there will be "Use of volatile is usually wrong" warnings
left.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:45 +0000 (15:55 +0000)]
board/fads/fads.c: Fix GCC 4.6 build warning
Fix:
fads.c: In function 'initdram':
fads.c:606:7: warning: variable 'base' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:44 +0000 (15:55 +0000)]
board/mbx8xx/mbx8xx.c: Fix GCC 4.6 build warnings
Fix:
mbx8xx.c: In function 'mbx_init':
mbx8xx.c:127:15: warning: variable 'refclock' set but not used
[-Wunused-but-set-variable]
mbx8xx.c: In function 'board_get_cpufreq':
mbx8xx.c:231:2: warning: dereferencing type-punned pointer will break
strict-aliasing rules [-Wstrict-aliasing]
mbx8xx.c: In function 'get_reffreq':
mbx8xx.c:242:2: warning: dereferencing type-punned pointer will break
strict-aliasing rules [-Wstrict-aliasing]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:43 +0000 (15:55 +0000)]
mpc8xx/spi.c: Fix GCC 4.6 build warnings
Fix:
spi.c: In function 'spi_init_f':
spi.c:144:21: warning: variable 'iop' set but not used
[-Wunused-but-set-variable]
spi.c:142:22: warning: variable 'cpi' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:42 +0000 (15:55 +0000)]
net/net.c: Fix GCC 4.6 build warning
Fix:
net.c: In function 'CDPHandler':
net.c:1083:8: warning: variable 'applid' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:41 +0000 (15:55 +0000)]
board/genietv/flash.c: Fix flash initialization
The GENIETV has only one NOR flash bank. Remove all code trying to
deal with a second bank. This also fixes a number of GCC 4.6 build
warnings:
flash.c:65:12: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:66:12: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:69:12: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:183:2: warning: format '%x' expects argument of type 'unsigned
int', but argument 2 has type '
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:40 +0000 (15:55 +0000)]
board/genietv/flash.c: CodingStyle cleanup
Make (mostly) checkpatch clean (don't convert to use I/O accessors yet,
so there will be "Use of volatile is usually wrong" warnings left.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:39 +0000 (15:55 +0000)]
board/etx094/flash.c: Fix flash initialization
The ETX094 has only one NOR flash bank. Remove all code trying to
deal with a second bank. This also fixes a number of GCC 4.6 build
warnings:
flash.c: In function 'flash_init':
flash.c:68:13: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:70:13: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:72:13: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:128:13: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:129:13: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:133:12: warning: array subscript is above array bounds
[-Warray-bounds]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:38 +0000 (15:55 +0000)]
board/etx094/flash.c: CodingStyle cleanup
Make (mostly) checkpatch clean (don't convert to use I/O accessors yet,
so there will be "Use of volatile is usually wrong" warnings left.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:37 +0000 (15:55 +0000)]
mpc8xx/i2c.c: replace PRINTD() by debug()
This also fixes some GCC 4.6 build warnings like:
warning: variable 'txbd' set but not used [-Wunused-but-set-variable]
warning: variable 'rxbd' set but not used [-Wunused-but-set-variable]
Signed-off-by: WOlfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:36 +0000 (15:55 +0000)]
mpc8xx/i2c.c: CodungStyle cleanup
Make (mostly) checkpatch-clean
We don't acctually change the code (like convert to use I/O
accessors), so there will be some remaining "Use of volatile"
warnings from checkpatch.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:35 +0000 (15:55 +0000)]
board/eltec/mhpc/flash.c: Fix GCC 4.6 build warning
Fix:
flash.c: In function 'write_buff':
flash.c:314:6: warning: variable 'count' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Frank Gottschling <fgottschling@eltec.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:34 +0000 (15:55 +0000)]
board/kup/kup4k/kup4k.c: Fix GCC 4.6 build warning
Fix:
kup4k.c: In function 'initdram':
kup4k.c:155:19: warning: variable 'mod' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Klaus Heydeck <heydeck@kieback-peter.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:33 +0000 (15:55 +0000)]
ICU862: Fix incorrect flash handling
There is only one bank of NOR flash memory on ICU862 boards.
Remove code that attempts to deal with a second bank.
This also fixes build warnings:
flash.c: In function 'flash_init':
flash.c:120:12: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:121:12: warning: array subscript is above array bounds
[-Warray-bounds]
flash.c:124:12: warning: array subscript is above array bounds
[-Warray-bounds]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 4 Nov 2011 15:55:32 +0000 (15:55 +0000)]
mpc8xx/cpu.c: Fix GCC 4.6 build warnings
Fix:
cpu.c: In function 'check_CPU':
cpu.c:188:8: warning: variable 'mid' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>