vfs: fix freeze protection in mnt_want_write_file() for overlayfs

[ Upstream commit a6795a585929d94ca3e931bc8518f8deb8bbe627 ]

The underlying real file used by overlayfs still contains the overlay path.
This results in mnt_want_write_file() calls by the filesystem getting
freeze protection on the wrong inode (the overlayfs one instead of the real
one).

Fix by using file_inode(file)->i_sb instead of file->f_path.mnt->mnt_sb.

Reported-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtdchar: fix overflows in adjustment of `count`

[ Upstream commit 6c6bc9ea84d0008024606bf5ba10519e20d851bf ]

The first checks in mtdchar_read() and mtdchar_write() attempt to limit
`count` such that `*ppos + count <= mtd->size`. However, they ignore the
possibility of `*ppos > mtd->size`, allowing the calculation of `count` to
wrap around. `mtdchar_lseek()` prevents seeking beyond mtd->size, but the
pread/pwrite syscalls bypass this.

I haven't found any codepath on which this actually causes dangerous
behavior, but it seems like a sensible change anyway.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

audit: fix use-after-free in audit_add_watch

[ Upstream commit baa2a4fdd525c8c4b0f704d20457195b29437839 ]

audit_add_watch stores locally krule->watch without taking a reference
on watch. Then, it calls audit_add_to_parent, and uses the watch stored
locally.

Unfortunately, it is possible that audit_add_to_parent updates
krule->watch.
When it happens, it also drops a reference of watch which
could free the watch.

How to reproduce (with KASAN enabled):

    auditctl -w /etc/passwd -F success=0 -k test_passwd
    auditctl -w /etc/passwd -F success=1 -k test_passwd2

The second call to auditctl triggers the use-after-free, because
audit_to_parent updates krule->watch to use a previous existing watch
and drops the reference to the newly created watch.

To fix the issue, we grab a reference of watch and we release it at the
end of the function.

Signed-off-by: Ronny Chevalier <ronny.chevalier@hp.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: dts: uniphier: Add missing cooling device properties for CPUs

[ Upstream commit af0e09d0c6762e486b0eb5cc4737396964c34fad ]

The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.

Add such missing properties.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: Add missing SET_DRIVER_VERSION command translation

[ Upstream commit 0f4039104ee61e14ac4771a2181c2a20572f4ec9 ]

When translating command opcodes to a string, SET_DRIVER_VERSION
command was missing.

Fixes: 42ca502e179d0 ('net/mlx5_core: Use a macro in mlx5_command_str()')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

binfmt_elf: Respect error return from `regset->active'

[ Upstream commit 2f819db565e82e5f73cd42b39925098986693378 ]

The regset API documented in <linux/regset.h> defines -ENODEV as the
result of the `->active' handler to be used where the feature requested
is not available on the hardware found.  However code handling core file
note generation in `fill_thread_core_info' interpretes any non-zero
result from the `->active' handler as the regset requested being active.
Consequently processing continues (and hopefully gracefully fails later
on) rather than being abandoned right away for the regset requested.

Fix the problem then by making the code proceed only if a positive
result is returned from the `->active' handler.

Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 4206d3aa1978 ("elf core dump: notes user_regset")
Patchwork: https://patchwork.linux-mips.org/patch/19332/
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

NFSv4.1 fix infinite loop on I/O.

commit 994b15b983a72e1148a173b61e5b279219bb45ae upstream.

The previous fix broke recovery of delegated stateids because it assumes
that if we did not mark the delegation as suspect, then the delegation has
effectively been revoked, and so it removes that delegation irrespectively
of whether or not it is valid and still in use. While this is "mostly
harmless" for ordinary I/O, we've seen pNFS fail with LAYOUTGET spinning
in an infinite loop while complaining that we're using an invalid stateid
(in this case the all-zero stateid).

What we rather want to do here is ensure that the delegation is always
correctly marked as needing testing when that is the case. So we want
to close the loophole offered by nfs4_schedule_stateid_recovery(),
which marks the state as needing to be reclaimed, but not the
delegation that may be backing it.

Fixes: 0e3d3e5df07dc ("NFSv4.1 fix infinite loop on IO BAD_STATEID error")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/EISA: Don't probe EISA bus for Xen PV guests

commit 6a92b11169a65b3f8cc512c75a252cbd0d096ba0 upstream.

For unprivileged Xen PV guests this is normal memory and ioremap will
not be able to properly map it.

While at it, since ioremap may return NULL, add a test for pointer's
validity.

Reported-by: Andy Smith <andy@strugglers.net>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: hpa@zytor.com
Cc: xen-devel@lists.xenproject.org
Cc: jgross@suse.com
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180911195538.23289-1-boris.ostrovsky@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf/core: Force USER_DS when recording user stack data

commit 02e184476eff848273826c1d6617bb37e5bcc7ad upstream.

Perf can record user stack data in response to a synchronous request, such
as a tracepoint firing. If this happens under set_fs(KERNEL_DS), then we
end up reading user stack data using __copy_from_user_inatomic() under
set_fs(KERNEL_DS). I think this conflicts with the intention of using
set_fs(KERNEL_DS). And it is explicitly forbidden by hardware on ARM64
when both CONFIG_ARM64_UAO and CONFIG_ARM64_PAN are used.

So fix this by forcing USER_DS when recording user stack data.

Signed-off-by: Yabin Cui <yabinc@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 88b0193d9418 ("perf/callchain: Force USER_DS when invoking perf_callchain_user()")
Link: http://lkml.kernel.org/r/20180823225935.27035-1-yabinc@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xtensa: ISS: don't allocate memory in platform_setup

commit ef439d49e0bfb26cd5f03c88b4cb7cc9073ed30c upstream.

Memory allocator is not initialized at that point yet, use static array
instead.

Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

CIFS: fix wrapping bugs in num_entries()

commit 56446f218af1133c802dad8e9e116f07f381846c upstream.

The problem is that "entryptr + next_offset" and "entryptr + len + size"
can wrap.  I ended up changing the type of "entryptr" because it makes
the math easier when we don't have to do so much casting.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: prevent integer overflow in nxt_dir_entry()

commit 8ad8aa353524d89fa2e09522f3078166ff78ec42 upstream.

The "old_entry + le32_to_cpu(pDirInfo->NextEntryOffset)" can wrap
around so I have added a check for integer overflow.

Reported-by: Dr Silvio Cesare of InfoSect <silvio.cesare@gmail.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "cdc-acm: implement put_char() and flush_chars()"

commit df3aa13c7bbb307e172c37f193f9a7aa058d4739 upstream.

This reverts commit a81cf9799ad7299b03a4dff020d9685f9ac5f3e0.

The patch causes a regression, which I cannot find the reason for.
So let's revert for now, as a revert hurts only performance.

Original report:
I was trying to resolve the problem with Oliver but we don't get any conclusion
for 5 months, so I am now sending this to mail list and cdc_acm authors.

I am using simple request-response protocol to obtain the boiller parameters
in constant intervals.

A simple one transaction is:
1. opening the /dev/ttyACM0
2. sending the following 10-bytes request to the device:
   unsigned char req[] = {0x02, 0xfe, 0x01, 0x05, 0x08, 0x02, 0x01, 0x69, 0xab, 0x03};
3. reading response (frame of 74 bytes length).
4. closing the descriptor
I am doing this transaction with 5 seconds intervals.

Before the bad commit everything was working correctly: I've got a requests and
a responses in a timely manner.

After the bad commit more time I am using the kernel module, more problems I have.
The graph [2] is showing the problem.

As you can see after module load all seems fine but after about 30 minutes I've got
a plenty of EAGAINs when doing read()'s and trying to read back the data.

When I rmmod and insmod the cdc_acm module again, then the situation is starting
over again: running ok shortly after load, and more time it is running, more EAGAINs
I have when calling read().

As a bonus I can see the problem on the device itself:
The device is configured as you can see here on this screen [3].
It has two transmision LEDs: TX and RX. Blink duration is set for 100ms.
This is a recording before the bad commit when all is working fine: [4]
And this is with the bad commit: [5]
As you can see the TX led is blinking wrongly long (indicating transmission?)
and I have problems doing read() calls (EAGAIN).

Reported-by: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: a81cf9799ad7 ("cdc-acm: implement put_char() and flush_chars()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: cdc-wdm: Fix a sleep-in-atomic-context bug in service_outstanding_interrupt()

commit 6e22e3af7bb3a7b9dc53cb4687659f6e63fca427 upstream.

wdm_in_callback() is a completion handler function for the USB driver.
So it should not sleep. But it calls service_outstanding_interrupt(),
which calls usb_submit_urb() with GFP_KERNEL.

To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC.

This bug is found by my static analysis tool DSAC.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: yurex: Fix buffer over-read in yurex_write()

commit 7e10f14ebface44a48275c8d6dc1caae3668d5a9 upstream.

If the written data starts with a digit, yurex_write() tries to parse
it as an integer using simple_strtoull().  This requires a null-
terminator, and currently there's no guarantee that there is one.

(The sample program at
https://github.com/NeoCat/YUREX-driver-for-Linux/blob/master/sample/yurex_clock.pl
writes an integer without a null terminator.  It seems like it must
have worked by chance!)

Always add a null byte after the written data.  Enlarge the buffer
to allow for this.

Cc: stable@vger.kernel.org
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: ti_usb_3410_5052: fix array underflow in completion handler

commit 5dfdd24eb3d39d815bc952ae98128e967c9bba49 upstream.

Similarly to a recently reported bug in io_ti, a malicious USB device
could set port_number to a negative value and we would underflow the
port array in the interrupt completion handler.

As these devices only have one or two ports, fix this by making sure we
only consider the seventh bit when determining the port number (and
ignore bits 0xb0 which are typically set to 0x30).

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: misc: uss720: Fix two sleep-in-atomic-context bugs

commit bc8acc214d3f1cafebcbcd101a695bbac716595d upstream.

async_complete() in uss720.c is a completion handler function for the
USB driver. So it should not sleep, but it is can sleep according to the
function call paths (from bottom to top) in Linux-4.16.

[FUNC] set_1284_register(GFP_KERNEL)
drivers/usb/misc/uss720.c, 372:
  set_1284_register in parport_uss720_frob_control
drivers/parport/ieee1284.c, 560:
  [FUNC_PTR]parport_uss720_frob_control in parport_ieee1284_ack_data_avail
drivers/parport/ieee1284.c, 577:
  parport_ieee1284_ack_data_avail in parport_ieee1284_interrupt
./include/linux/parport.h, 474:
  parport_ieee1284_interrupt in parport_generic_irq
drivers/usb/misc/uss720.c, 116:
  parport_generic_irq in async_complete

[FUNC] get_1284_register(GFP_KERNEL)
drivers/usb/misc/uss720.c, 382:
  get_1284_register in parport_uss720_read_status
drivers/parport/ieee1284.c, 555:
  [FUNC_PTR]parport_uss720_read_status in parport_ieee1284_ack_data_avail
drivers/parport/ieee1284.c, 577:
  parport_ieee1284_ack_data_avail in parport_ieee1284_interrupt
./include/linux/parport.h, 474:
  parport_ieee1284_interrupt in parport_generic_irq
drivers/usb/misc/uss720.c, 116:
  parport_generic_irq in async_complete

Note that [FUNC_PTR] means a function pointer call is used.

To fix these bugs, GFP_KERNEL is replaced with GFP_ATOMIC.

These bugs are found by my static analysis tool DSAC.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: io_ti: fix array underflow in completion handler

commit 691a03cfe8ca483f9c48153b869d354e4ae3abef upstream.

As reported by Dan Carpenter, a malicious USB device could set
port_number to a negative value and we would underflow the port array in
the interrupt completion handler.

As these devices only have one or two ports, fix this by making sure we
only consider the seventh bit when determining the port number (and
ignore bits 0xb0 which are typically set to 0x30).

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: net2280: Fix erroneous synchronization change

commit dec3c23c9aa1815f07d98ae0375b4cbc10971e13 upstream.

Commit f16443a034c7 ("USB: gadgetfs, dummy-hcd, net2280: fix locking
for callbacks") was based on a serious misunderstanding.  It
introduced regressions into both the dummy-hcd and net2280 drivers.

The problem in dummy-hcd was fixed by commit 7dbd8f4cabd9 ("USB:
dummy-hcd: Fix erroneous synchronization change"), but the problem in
net2280 remains.  Namely: the ->disconnect(), ->suspend(), ->resume(),
and ->reset() callbacks must be invoked without the private lock held;
otherwise a deadlock will occur when the callback routine tries to
interact with the UDC driver.

This patch largely is a reversion of the relevant parts of
f16443a034c7.  It also drops the private lock around the calls to
->suspend() and ->resume() (something the earlier patch forgot to do).
This is safe from races with device interrupts because it occurs
within the interrupt handler.

Finally, the patch changes where the ->disconnect() callback is
invoked when net2280_pullup() turns the pullup off.  Rather than
making the callback from within stop_activity() at a time when dropping
the private lock could be unsafe, the callback is moved to a point
after the lock has already been dropped.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: f16443a034c7 ("USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks")
Reported-by: D. Ziesche <dziesche@zes.com>
Tested-by: D. Ziesche <dziesche@zes.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: udc: renesas_usb3: fix maxpacket size of ep0

commit dfe1a51d2a36647f74cbad478801efa7cf394376 upstream.

This patch fixes an issue that maxpacket size of ep0 is incorrect
for SuperSpeed. Otherwise, CDC NCM class with SuperSpeed doesn't
work correctly on this driver because its control read data size
is more than 64 bytes.

Reported-by: Junki Kato <junki.kato.xk@renesas.com>
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Junki Kato <junki.kato.xk@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: add quirk for WORLDE Controller KS49 or Prodipe MIDI 49C USB controller

commit 9b83a1c301ad6d24988a128c69b42cbaaf537d82 upstream.

WORLDE Controller KS49 or Prodipe MIDI 49C USB controller
cause a -EPROTO error, a communication restart and loop again.

This issue has already been fixed for KS25.
https://lore.kernel.org/patchwork/patch/753077/

I just add device 201 for KS49 in quirks.c to get it works.

Signed-off-by: Laurent Roux <xpros64@hotmail.fr>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: host: u132-hcd: Fix a sleep-in-atomic-context bug in u132_get_frame()

commit 6d4f268fa132742fe96dad22307c68d237356d88 upstream.

i_usX2Y_subs_startup in usbusx2yaudio.c is a completion handler function
for the USB driver. So it should not sleep, but it is can sleep
according to the function call paths (from bottom to top) in Linux-4.16.

[FUNC] msleep
drivers/usb/host/u132-hcd.c, 2558:
msleep in u132_get_frame
drivers/usb/core/hcd.c, 2231:
[FUNC_PTR]u132_get_frame in usb_hcd_get_frame_number
drivers/usb/core/usb.c, 822:
usb_hcd_get_frame_number in usb_get_current_frame_number
sound/usb/usx2y/usbusx2yaudio.c, 303:
usb_get_current_frame_number in i_usX2Y_urb_complete
sound/usb/usx2y/usbusx2yaudio.c, 366:
i_usX2Y_urb_complete in i_usX2Y_subs_startup

Note that [FUNC_PTR] means a function pointer call is used.

To fix this bug, msleep() is replaced with mdelay().

This bug is found by my static analysis tool DSAC.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: Avoid use-after-free by flushing endpoints early in usb_set_interface()

commit f9a5b4f58b280c1d26255376713c132f93837621 upstream.

The steps taken by usb core to set a new interface is very different from
what is done on the xHC host side.

xHC hardware will do everything in one go. One command is used to set up
new endpoints, free old endpoints, check bandwidth, and run the new
endpoints.

All this is done by xHC when usb core asks the hcd to check for
available bandwidth. At this point usb core has not yet flushed the old
endpoints, which will cause use-after-free issues in xhci driver as
queued URBs are cancelled on a re-allocated endpoint.

To resolve this add a call to usb_disable_interface() which will flush
the endpoints before calling usb_hcd_alloc_bandwidth()

Additional checks in xhci driver will also be implemented to gracefully
handle stale URB cancel on freed and re-allocated endpoints

Cc: <stable@vger.kernel.org>
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: uas: add support for more quirk flags

commit 42d1c6d4a06a77b3ab206a919b9050c3080f3a71 upstream.

The hope that UAS devices would be less broken than old style storage
devices has turned out to be unfounded. Make UAS support more of the
quirk flags of the old driver.

Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: Add quirk to support DJI CineSSD

commit f45681f9becaa65111ed0a691ccf080a0cd5feb8 upstream.

This device does not correctly handle the LPM operations.

Also, the device cannot handle ATA pass-through commands
and locks up when attempted while running in super speed.

This patch adds the equivalent quirk logic as found in uas.

Signed-off-by: Tim Anderson <tsa@biglakesoftware.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mei: bus: need to unlink client before freeing

commit 34f1166afd67f9f48a08c52f36180048908506a4 upstream.

In case a client fails to connect in mei_cldev_enable(), the
caller won't call the mei_cldev_disable leaving the client
in a linked stated. Upon driver unload the client structure
will be freed in  mei_cl_bus_dev_release(), leaving a stale pointer
on a fail_list.  This will eventually end up in crash
during power down flow in mei_cl_set_disonnected().

RIP:  mei_cl_set_disconnected+0x5/0x260[mei]
Call trace:
mei_cl_all_disconnect+0x22/0x30
mei_reset+0x194/0x250
__synchronize_hardirq+0x43/0x50
_cond_resched+0x15/0x30
mei_me_intr_clear+0x20/0x100
mei_stop+0x76/0xb0
mei_me_shutdown+0x3f/0x80
pci_device_shutdown+0x34/0x60
kernel_restart+0x0e/0x30

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200455
Fixes: 'c110cdb17148 ("mei: bus: make a client pointer always available")'
Cc: <stable@vger.kernel.org> 4.10+
Tested-by: Georg Müller <georgmueller@gmx.net>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mei: ignore not found client in the enumeration

commit 8d2d8935d30cc2acc57a3196dc10dfa8d5cbcdab upstream.

Some of the ME clients are available only for BIOS operation and are
removed during hand off to an OS. However the removal is not instant.
A client may be visible on the client list when the mei driver requests
for enumeration, while the subsequent request for properties will be
answered with client not found error value. The default behavior
for an error is to perform client reset while this error is harmless and
the link reset should be prevented. This issue started to be visible due to
suspend/resume timing changes. Currently reported only on the Haswell
based system.

Fixes:
[33.564957] mei_me 0000:00:16.0: hbm: properties response: wrong status = 1 CLIENT_NOT_FOUND
[33.564978] mei_me 0000:00:16.0: mei_irq_read_handler ret = -71.
[33.565270] mei_me 0000:00:16.0: unexpected reset: dev_state = INIT_CLIENTS fw status = 1E000255 60002306 00000200 00004401 00000000 00000010

Cc: <stable@vger.kernel.org>
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: Don't die twice if PCI xhci host is not responding in resume

commit f3dc41c5d22b2ca14a0802a65d8cdc33a3882d4e upstream.

usb_hc_died() should only be called once, and with the primary HCD
as parameter. It will mark both primary and secondary hcd's dead.

Remove the extra call to usb_cd_died with the shared hcd as parameter.

Fixes: ff9d78b36f76 ("USB: Set usb_hcd->state and flags for shared roothubs")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci: Fix use after free for URB cancellation on a reallocated endpoint

commit 4937213ba7fafa13f30496b3965ffe93970d8b53 upstream.

Make sure the cancelled URB is on the current endpoint ring.

If the endpoint ring has been reallocated since the URB was enqueued
then the URB may contain TD and TRB pointers to a already freed ring.
In this the case return the URB without touching any of the freed ring
structure data.

Don't try to stop the ring. It would be useless.

This can occur if endpoint is not flushed before it is dropped and
re-added, which is the case in usb_set_interface() as xhci does
things in an odd order.

Cc: <stable@vger.kernel.org>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

misc: hmc6352: fix potential Spectre v1

commit de916736aaaadddbd6061472969f667b14204aa9 upstream.

val is indirectly controlled by user-space, hence leading to a
potential exploitation of the Spectre variant 1 vulnerability.

This issue was detected with the help of Smatch:

drivers/misc/hmc6352.c:54 compass_store() warn: potential spectre issue
'map' [r]

Fix this by sanitizing val before using it to index map

Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].

[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2

Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Tools: hv: Fix a bug in the key delete code

commit 86503bd35dec0ce363e9fdbf5299927422ed3899 upstream.

Fix a bug in the key delete code - the num_records range
from 0 to num_records-1.

Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipmi: Fix I2C client removal in the SSIF driver

commit 0745dde62835be7e2afe62fcdb482fcad79cb743 upstream.

The SSIF driver was removing any client that came in through the
platform interface, but it should only remove clients that it
added.  On a failure in the probe function, this could result
in the following oops when the driver is removed and the
client gets unregistered twice:

 CPU: 107 PID: 30266 Comm: rmmod Not tainted 4.18.0+ #80
 Hardware name: Cavium Inc. Saber/Saber, BIOS Cavium reference firmware version 7.0 08/04/2018
 pstate: 60400009 (nZCv daif +PAN -UAO)
 pc : kernfs_find_ns+0x28/0x120
 lr : kernfs_find_and_get_ns+0x40/0x60
 sp : ffff00002310fb50
 x29: ffff00002310fb50 x28: ffff800a8240f800
 x27: 0000000000000000 x26: 0000000000000000
 x25: 0000000056000000 x24: ffff000009073000
 x23: ffff000008998b38 x22: 0000000000000000
 x21: ffff800ed86de820 x20: 0000000000000000
 x19: ffff00000913a1d8 x18: 0000000000000000
 x17: 0000000000000000 x16: 0000000000000000
 x15: 0000000000000000 x14: 5300737265766972
 x13: 643d4d4554535953 x12: 0000000000000030
 x11: 0000000000000030 x10: 0101010101010101
 x9 : ffff800ea06cc3f9 x8 : 0000000000000000
 x7 : 0000000000000141 x6 : ffff000009073000
 x5 : ffff800adb706b00 x4 : 0000000000000000
 x3 : 00000000ffffffff x2 : 0000000000000000
 x1 : ffff000008998b38 x0 : ffff000008356760
 Process rmmod (pid: 30266, stack limit = 0x00000000e218418d)
 Call trace:
  kernfs_find_ns+0x28/0x120
  kernfs_find_and_get_ns+0x40/0x60
  sysfs_unmerge_group+0x2c/0x6c
  dpm_sysfs_remove+0x34/0x70
  device_del+0x58/0x30c
  device_unregister+0x30/0x7c
  i2c_unregister_device+0x84/0x90 [i2c_core]
  ssif_platform_remove+0x38/0x98 [ipmi_ssif]
  platform_drv_remove+0x2c/0x6c
  device_release_driver_internal+0x168/0x1f8
  driver_detach+0x50/0xbc
  bus_remove_driver+0x74/0xe8
  driver_unregister+0x34/0x5c
  platform_driver_unregister+0x20/0x2c
  cleanup_ipmi_ssif+0x50/0xd82c [ipmi_ssif]
  __arm64_sys_delete_module+0x1b4/0x220
  el0_svc_handler+0x104/0x160
  el0_svc+0x8/0xc
 Code: aa1e03e0 aa0203f6 aa0103f7 d503201f (7940e280)
 ---[ end trace 09f0e34cce8e2d8c ]---
 Kernel panic - not syncing: Fatal exception
 SMP: stopping secondary CPUs
 Kernel Offset: disabled
 CPU features: 0x23800c38

So track the clients that the SSIF driver adds and only remove
those.

Reported-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: George Cherian <george.cherian@cavium.com>
Cc: <stable@vger.kernel.org> # 4.14.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: omap_hsmmc: fix wakeirq handling on removal

commit 3c398f3c3bef21961eaaeb93227fa66d440dc83d upstream.

after unbinding mmc I get things like this:
[  185.294067] mmc1: card 0001 removed
[  185.305206] omap_hsmmc 480b4000.mmc: wake IRQ with no resume: -13

The wakeirq stays in /proc-interrupts

rebinding shows this:
[  289.795959] genirq: Flags mismatch irq 112. 0000200a (480b4000.mmc:wakeup) vs. 0000200a (480b4000.mmc:wakeup)
[  289.808959] omap_hsmmc 480b4000.mmc: Unable to request wake IRQ
[  289.815338] omap_hsmmc 480b4000.mmc: no SDIO IRQ support, falling back to polling

That bug seems to be introduced by switching from devm_request_irq()
to generic wakeirq handling.

So let us cleanup at removal.

Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Fixes: 5b83b2234be6 ("mmc: omap_hsmmc: Change wake-up interrupt to use generic wakeirq")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/crypto: Fix return code checking in cbc_paes_crypt()

commit b81126e01a8c6048249955feea46c8217ebefa91 upstream.

The return code of cpacf_kmc() is less than the number of
bytes to process in case of an error, not greater.
The crypt routines for the other cipher modes already have
this correctly.

Cc: stable@vger.kernel.org # v4.11+
Fixes: 279378430768 ("s390/crypt: Add protected key AES module")
Signed-off-by: Ingo Franzki <ifranzki@linux.ibm.com>
Acked-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/ipoib: Avoid a race condition between start_xmit and cm_rep_handler

commit 816e846c2eb9129a3e0afa5f920c8bbc71efecaa upstream.

Inside of start_xmit() the call to check if the connection is up and the
queueing of the packets for later transmission is not atomic which leaves
a window where cm_rep_handler can run, set the connection up, dequeue
pending packets and leave the subsequently queued packets by start_xmit()
sitting on neigh->queue until they're dropped when the connection is torn
down. This only applies to connected mode. These dropped packets can
really upset TCP, for example, and cause multi-minute delays in
transmission for open connections.

Here's the code in start_xmit where we check to see if the connection is
up:

       if (ipoib_cm_get(neigh)) {
               if (ipoib_cm_up(neigh)) {
                       ipoib_cm_send(dev, skb, ipoib_cm_get(neigh));
                       goto unref;
               }
       }

The race occurs if cm_rep_handler execution occurs after the above
connection check (specifically if it gets to the point where it acquires
priv->lock to dequeue pending skb's) but before the below code snippet in
start_xmit where packets are queued.

       if (skb_queue_len(&neigh->queue) < IPOIB_MAX_PATH_REC_QUEUE) {
               push_pseudo_header(skb, phdr->hwaddr);
               spin_lock_irqsave(&priv->lock, flags);
               __skb_queue_tail(&neigh->queue, skb);
               spin_unlock_irqrestore(&priv->lock, flags);
       } else {
               ++dev->stats.tx_dropped;
               dev_kfree_skb_any(skb);
       }

The patch acquires the netif tx lock in cm_rep_handler for the section
where it sets the connection up and dequeues and retransmits deferred
skb's.

Fixes: 839fcaba355a ("IPoIB: Connected mode experimental support")
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Knister <aaron.s.knister@nasa.gov>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen/netfront: fix waiting for xenbus state change

commit 8edfe2e992b75aee3da9316e9697c531194c2f53 upstream.

Commit 822fb18a82aba ("xen-netfront: wait xenbus state change when load
module manually") added a new wait queue to wait on for a state change
when the module is loaded manually. Unfortunately there is no wakeup
anywhere to stop that waiting.

Instead of introducing a new wait queue rename the existing
module_unload_q to module_wq and use it for both purposes (loading and
unloading).

As any state change of the backend might be intended to stop waiting
do the wake_up_all() in any case when netback_changed() is called.

Fixes: 822fb18a82aba ("xen-netfront: wait xenbus state change when load module manually")
Cc: <stable@vger.kernel.org> #4.18
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pstore: Fix incorrect persistent ram buffer mapping

commit 831b624df1b420c8f9281ed1307a8db23afb72df upstream.

persistent_ram_vmap() returns the page start vaddr.
persistent_ram_iomap() supports non-page-aligned mapping.

persistent_ram_buffer_map() always adds offset-in-page to the vaddr
returned from these two functions, which causes incorrect mapping of
non-page-aligned persistent ram buffer.

By default ftrace_size is 4096 and max_ftrace_cnt is nr_cpu_ids. Without
this patch, the zone_sz in ramoops_init_przs() is 4096/nr_cpu_ids which
might not be page aligned. If the offset-in-page > 2048, the vaddr will be
in next page. If the next page is not mapped, it will cause kernel panic:

[    0.074231] BUG: unable to handle kernel paging request at ffffa19e0081b000
...
[    0.075000] RIP: 0010:persistent_ram_new+0x1f8/0x39f
...
[    0.075000] Call Trace:
[    0.075000]  ramoops_init_przs.part.10.constprop.15+0x105/0x260
[    0.075000]  ramoops_probe+0x232/0x3a0
[    0.075000]  platform_drv_probe+0x3e/0xa0
[    0.075000]  driver_probe_device+0x2cd/0x400
[    0.075000]  __driver_attach+0xe4/0x110
[    0.075000]  ? driver_probe_device+0x400/0x400
[    0.075000]  bus_for_each_dev+0x70/0xa0
[    0.075000]  driver_attach+0x1e/0x20
[    0.075000]  bus_add_driver+0x159/0x230
[    0.075000]  ? do_early_param+0x95/0x95
[    0.075000]  driver_register+0x70/0xc0
[    0.075000]  ? init_pstore_fs+0x4d/0x4d
[    0.075000]  __platform_driver_register+0x36/0x40
[    0.075000]  ramoops_init+0x12f/0x131
[    0.075000]  do_one_initcall+0x4d/0x12c
[    0.075000]  ? do_early_param+0x95/0x95
[    0.075000]  kernel_init_freeable+0x19b/0x222
[    0.075000]  ? rest_init+0xbb/0xbb
[    0.075000]  kernel_init+0xe/0xfc
[    0.075000]  ret_from_fork+0x3a/0x50

Signed-off-by: Bin Yang <bin.yang@intel.com>
[kees: add comments describing the mapping differences, updated commit log]
Fixes: 24c3d2f342ed ("staging: android: persistent_ram: Make it possible to use memory outside of bootmem")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/cma: Protect cma dev list with lock

commit 954a8e3aea87e896e320cf648c1a5bbe47de443e upstream.

When AF_IB addresses are used during rdma_resolve_addr() a lock is not
held. A cma device can get removed while list traversal is in progress
which may lead to crash. ie

        CPU0                                     CPU1
        ====                                     ====
rdma_resolve_addr()
 cma_resolve_ib_dev()
  list_for_each()                         cma_remove_one()
    cur_dev->device                        mutex_lock(&lock)
                                            list_del();
                                           mutex_unlock(&lock);
                                           cma_process_remove();

Therefore, hold a lock while traversing the list which avoids such
situation.

Cc: <stable@vger.kernel.org> # 3.10
Fixes: f17df3b0dede ("RDMA/cma: Add support for AF_IB to rdma_resolve_addr()")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen-netfront: fix warn message as irq device name has '/'

[ Upstream commit 21f2706b20100bb3db378461ab9b8e2035309b5b ]

There is a call trace generated after commit 2d408c0d4574b01b9ed45e02516888bf925e11a9(
xen-netfront: fix queue name setting). There is no 'device/vif/xx-q0-tx' file found
under /proc/irq/xx/.

This patch only picks up device type and id as its name.

With the patch, now /proc/interrupts looks like below and the warning message gone:
 70:         21          0          0          0   xen-dyn    -event     vif0-q0-tx
 71:         15          0          0          0   xen-dyn    -event     vif0-q0-rx
 72:         14          0          0          0   xen-dyn    -event     vif0-q1-tx
 73:         33          0          0          0   xen-dyn    -event     vif0-q1-rx
 74:         12          0          0          0   xen-dyn    -event     vif0-q2-tx
 75:         24          0          0          0   xen-dyn    -event     vif0-q2-rx
 76:         19          0          0          0   xen-dyn    -event     vif0-q3-tx
 77:         21          0          0          0   xen-dyn    -event     vif0-q3-rx

Below is call trace information without this patch:

name 'device/vif/0-q0-tx'
WARNING: CPU: 2 PID: 37 at fs/proc/generic.c:174 __xlate_proc_name+0x85/0xa0
RIP: 0010:__xlate_proc_name+0x85/0xa0
RSP: 0018:ffffb85c40473c18 EFLAGS: 00010286
RAX: 0000000000000000 RBX: 0000000000000006 RCX: 0000000000000006
RDX: 0000000000000007 RSI: 0000000000000096 RDI: ffff984c7f516930
RBP: ffffb85c40473cb8 R08: 000000000000002c R09: 0000000000000229
R10: 0000000000000000 R11: 0000000000000001 R12: ffffb85c40473c98
R13: ffffb85c40473cb8 R14: ffffb85c40473c50 R15: 0000000000000000
FS:  0000000000000000(0000) GS:ffff984c7f500000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f69b6899038 CR3: 000000001c20a006 CR4: 00000000001606e0
Call Trace:
__proc_create+0x45/0x230
? snprintf+0x49/0x60
proc_mkdir_data+0x35/0x90
register_handler_proc+0xef/0x110
? proc_register+0xfc/0x110
? proc_create_data+0x70/0xb0
__setup_irq+0x39b/0x660
? request_threaded_irq+0xad/0x160
request_threaded_irq+0xf5/0x160
? xennet_tx_buf_gc+0x1d0/0x1d0 [xen_netfront]
bind_evtchn_to_irqhandler+0x3d/0x70
? xenbus_alloc_evtchn+0x41/0xa0
netback_changed+0xa46/0xcda [xen_netfront]
? find_watch+0x40/0x40
xenwatch_thread+0xc5/0x160
? finish_wait+0x80/0x80
kthread+0x112/0x130
? kthread_create_worker_on_cpu+0x70/0x70
ret_from_fork+0x35/0x40
Code: 81 5c 00 48 85 c0 75 cc 5b 49 89 2e 31 c0 5d 4d 89 3c 24 41 5c 41 5d 41 5e 41 5f c3 4c 89 ee 48 c7 c7 40 4f 0e b4 e8 65 ea d8 ff <0f> 0b b8 fe ff ff ff 5b 5d 41 5c 41 5d 41 5e 41 5f c3 66 0f 1f
---[ end trace 650e5561b0caab3a ]---

Signed-off-by: Xiao Liang <xiliang@redhat.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/mm/pti: Add an overflow check to pti_clone_pmds()

[ Upstream commit 935232ce28dfabff1171e5a7113b2d865fa9ee63 ]

The addr counter will overflow if the last PMD of the address space is
cloned, resulting in an endless loop.

Check for that and bail out of the loop when it happens.

Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Pavel Machek <pavel@ucw.cz>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: linux-mm@kvack.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David Laight <David.Laight@aculab.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Eduardo Valentin <eduval@amazon.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: aliguori@amazon.com
Cc: daniel.gruss@iaik.tugraz.at
Cc: hughd@google.com
Cc: keescook@google.com
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Waiman Long <llong@redhat.com>
Cc: "David H . Gutteridge" <dhgutteridge@sympatico.ca>
Cc: joro@8bytes.org
Link: https://lkml.kernel.org/r/1531906876-13451-25-git-send-email-joro@8bytes.org
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/pti: Check the return value of pti_user_pagetable_walk_pmd()

[ Upstream commit 8c934e01a7ce685d98e970880f5941d79272c654 ]

pti_user_pagetable_walk_pmd() can return NULL, so the return value should
be checked to prevent a NULL pointer dereference.

Add the check and a warning when the PMD allocation fails.

Signed-off-by: Jiang Biao <jiang.biao2@zte.com.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: dave.hansen@linux.intel.com
Cc: luto@kernel.org
Cc: hpa@zytor.com
Cc: albcamus@gmail.com
Cc: zhong.weidong@zte.com.cn
Link: https://lkml.kernel.org/r/1532045192-49622-2-git-send-email-jiang.biao2@zte.com.cn
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/pti: Check the return value of pti_user_pagetable_walk_p4d()

[ Upstream commit b2b7d986a89b6c94b1331a909de1217214fb08c1 ]

pti_user_pagetable_walk_p4d() can return NULL, so the return value should
be checked to prevent a NULL pointer dereference.

Add the check and a warning when the P4D allocation fails.

Signed-off-by: Jiang Biao <jiang.biao2@zte.com.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: dave.hansen@linux.intel.com
Cc: luto@kernel.org
Cc: hpa@zytor.com
Cc: albcamus@gmail.com
Cc: zhong.weidong@zte.com.cn
Link: https://lkml.kernel.org/r/1532045192-49622-1-git-send-email-jiang.biao2@zte.com.cn
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: sharah - Unregister correct algorithms for SAHARA 3

[ Upstream commit 0e7d4d932ffc23f75efb31a8c2ac2396c1b81c55 ]

This patch fixes two typos related to unregistering algorithms supported by
SAHARAH 3. In sahara_register_algs the wrong algorithms are unregistered
in case of an error. In sahara_unregister_algs the wrong array is used to
determine the iteration count.

Signed-off-by: Michael Müller <michael@fds-team.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dmaengine: mv_xor_v2: kill the tasklets upon exit

[ Upstream commit 8bbafed8dd5cfa81071b50ead5cb60367fdef3a9 ]

The mv_xor_v2 driver uses a tasklet, initialized during the probe()
routine. However, it forgets to cleanup the tasklet using
tasklet_kill() function during the remove() routine, which this patch
fixes. This prevents the tasklet from potentially running after the
module has been removed.

Fixes: 19a340b1a820 ("dmaengine: mv_xor_v2: new driver")

Signed-off-by: Hanna Hawa <hannah@marvell.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i2c: aspeed: Fix initial values of master and slave state

[ Upstream commit 517fde0eb5a8f46c54ba6e2c36e32563b23cb14f ]

This patch changes the order of enum aspeed_i2c_master_state and
enum aspeed_i2c_slave_state defines to make their initial value to
ASPEED_I2C_MASTER_INACTIVE and ASPEED_I2C_SLAVE_STOP respectively.
In case of multi-master use, if a slave data comes ahead of the
first master xfer, master_state starts from an invalid state so
this change fixes the issue.

Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/base: stop new probing during shutdown

[ Upstream commit 3297c8fc65af5d40501ea7cddff1b195cae57e4e ]

There is a race window in device_shutdown(), which may cause
-1. parent device shut down before child or
-2. no shutdown on a new probing device.

For 1st, taking the following scenario:
         device_shutdown                        new plugin device
  list_del_init(parent_dev);
  spin_unlock(list_lock);
                                                  device_add(child)
                                                  probe child
  shutdown parent_dev
       --> now child is on the tail of devices_kset

For 2nd, taking the following scenario:
         device_shutdown                        new plugin device
                                                  device_add(dev)
  device_lock(dev);
  ...
  device_unlock(dev);
                                                  probe dev
       --> now, the new occurred dev has no opportunity to shutdown

To fix this race issue, just prevent the new probing request. With this
logic, device_shutdown() is more similar to dpm_prepare().

Signed-off-by: Pingfan Liu <kernelfans@gmail.com>
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: arm/arm64: Fix vgic init race

[ Upstream commit 1d47191de7e15900f8fbfe7cccd7c6e1c2d7c31a ]

The vgic_init function can race with kvm_arch_vcpu_create() which does
not hold kvm_lock() and we therefore have no synchronization primitives
to ensure we're doing the right thing.

As the user is trying to initialize or run the VM while at the same time
creating more VCPUs, we just have to refuse to initialize the VGIC in
this case rather than silently failing with a broken VCPU.

Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

platform/x86: toshiba_acpi: Fix defined but not used build warnings

[ Upstream commit c2e2a618eb7104e18fdcf739d4d911563812a81c ]

Fix a build warning in toshiba_acpi.c when CONFIG_PROC_FS is not enabled
by marking the unused function as __maybe_unused.

../drivers/platform/x86/toshiba_acpi.c:1685:12: warning: 'version_proc_show' defined but not used [-Wunused-function]

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Azael Avalos <coproscefalo@gmail.com>
Cc: platform-driver-x86@vger.kernel.org
Cc: Andy Shevchenko <andy@infradead.org>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/qeth: reset layer2 attribute on layer switch

[ Upstream commit 70551dc46ffa3555a0b5f3545b0cd87ab67fd002 ]

After the subdriver's remove() routine has completed, the card's layer
mode is undetermined again. Reflect this in the layer2 field.

If qeth_dev_layer2_store() hits an error after remove() was called, the
card _always_ requires a setup(), even if the previous layer mode is
requested again.
But qeth_dev_layer2_store() bails out early if the requested layer mode
still matches the current one. So unless we reset the layer2 field,
re-probing the card back to its previous mode is currently not possible.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/qeth: fix race in used-buffer accounting

[ Upstream commit a702349a4099cd5a7bab0904689d8e0bf8dcd622 ]

By updating q->used_buffers only _after_ do_QDIO() has completed, there
is a potential race against the buffer's TX completion. In the unlikely
case that the TX completion path wins, qeth_qdio_output_handler() would
decrement the counter before qeth_flush_buffers() even incremented it.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: qcom: msm8974-hammerhead: increase load on l20 for sdhci

[ Upstream commit 03864e57770a9541e7ff3990bacf2d9a2fffcd5d ]

The kernel would not boot on the hammerhead hardware due to the
following error:

mmc0: Timeout waiting for hardware interrupt.
mmc0: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc0: sdhci: Sys addr:  0x00000200 | Version:  0x00003802
mmc0: sdhci: Blk size:  0x00000200 | Blk cnt:  0x00000200
mmc0: sdhci: Argument:  0x00000000 | Trn mode: 0x00000023
mmc0: sdhci: Present:   0x03e80000 | Host ctl: 0x00000034
mmc0: sdhci: Power:     0x00000001 | Blk gap:  0x00000000
mmc0: sdhci: Wake-up:   0x00000000 | Clock:    0x00000007
mmc0: sdhci: Timeout:   0x0000000e | Int stat: 0x00000000
mmc0: sdhci: Int enab:  0x02ff900b | Sig enab: 0x02ff100b
mmc0: sdhci: AC12 err:  0x00000000 | Slot int: 0x00000000
mmc0: sdhci: Caps:      0x642dc8b2 | Caps_1:   0x00008007
mmc0: sdhci: Cmd:       0x00000c1b | Max curr: 0x00000000
mmc0: sdhci: Resp[0]:   0x00000c00 | Resp[1]:  0x00000000
mmc0: sdhci: Resp[2]:   0x00000000 | Resp[3]:  0x00000000
mmc0: sdhci: Host ctl2: 0x00000008
mmc0: sdhci: ADMA Err:  0x00000000 | ADMA Ptr: 0x70040220
mmc0: sdhci: ============================================
mmc0: Card stuck in wrong state! mmcblk0 card_busy_detect status: 0xe00
mmc0: cache flush error -110
mmc0: Reset 0x1 never completed.

This patch increases the load on l20 to 0.2 amps for the sdhci
and allows the device to boot normally.

Signed-off-by: Bhushan Shah <bshah@kde.org>
Signed-off-by: Brian Masney <masneyb@onstation.org>
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: dts: qcom: db410c: Fix Bluetooth LED trigger

[ Upstream commit e53db018315b7660bb7000a29e79faff2496c2c2 ]

Current LED trigger, 'bt', is not known/used by any existing driver.
Fix this by renaming it to 'bluetooth-power' trigger which is
controlled by the Bluetooth subsystem.

Fixes: 9943230c8860 ("arm64: dts: qcom: Add apq8016-sbc board LED's related device nodes")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen-netfront: fix queue name setting

[ Upstream commit 2d408c0d4574b01b9ed45e02516888bf925e11a9 ]

Commit f599c64fdf7d ("xen-netfront: Fix race between device setup and
open") changed the initialization order: xennet_create_queues() now
happens before we do register_netdev() so using netdev->name in
xennet_init_queue() is incorrect, we end up with the following in
/proc/interrupts:

 60:        139          0   xen-dyn    -event     eth%d-q0-tx
 61:        265          0   xen-dyn    -event     eth%d-q0-rx
 62:        234          0   xen-dyn    -event     eth%d-q1-tx
 63:          1          0   xen-dyn    -event     eth%d-q1-rx

and this looks ugly. Actually, using early netdev name (even when it's
already set) is also not ideal: nowadays we tend to rename eth devices
and queue name may end up not corresponding to the netdev name.

Use nodename from xenbus device for queue naming: this can't change in VM's
lifetime. Now /proc/interrupts looks like

 62:        202          0   xen-dyn    -event     device/vif/0-q0-tx
 63:        317          0   xen-dyn    -event     device/vif/0-q0-rx
 64:        262          0   xen-dyn    -event     device/vif/0-q1-tx
 65:         17          0   xen-dyn    -event     device/vif/0-q1-rx

Fixes: f599c64fdf7d ("xen-netfront: Fix race between device setup and open")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nfp: avoid buffer leak when FW communication fails

[ Upstream commit 07300f774fec9519663a597987a4083225588be4 ]

After device is stopped we reset the rings by moving all free buffers
to positions [0, cnt - 2], and clear the position cnt - 1 in the ring.
We then proceed to clear the read/write pointers.  This means that if
we try to reset the ring again the code will assume that the next to
fill buffer is at position 0 and swap it with cnt - 1.  Since we
previously cleared position cnt - 1 it will lead to leaking the first
buffer and leaving ring in a bad state.

This scenario can only happen if FW communication fails, in which case
the ring will never be used again, so the fact it's in a bad state will
not be noticed.  Buffer leak is the only problem.  Don't try to move
buffers in the ring if the read/write pointers indicate the ring was
never used or have already been reset.

nfp_net_clear_config_and_disable() is now fully idempotent.

Found by code inspection, FW communication failures are very rare,
and reconfiguring a live device is not common either, so it's unlikely
anyone has ever noticed the leak.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

efi/arm: preserve early mapping of UEFI memory map longer for BGRT

[ Upstream commit 3ea86495aef2f6de26b7cb1599ba350dd6a0c521 ]

The BGRT code validates the contents of the table against the UEFI
memory map, and so it expects it to be mapped when the code runs.

On ARM, this is currently not the case, since we tear down the early
mapping after efi_init() completes, and only create the permanent
mapping in arm_enable_runtime_services(), which executes as an early
initcall, but still leaves a window where the UEFI memory map is not
mapped.

So move the call to efi_memmap_unmap() from efi_init() to
arm_enable_runtime_services().

Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: fold in EFI_MEMMAP attribute check from Ard]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

reset: imx7: Fix always writing bits as 0

[ Upstream commit 26fce0557fa639fb7bbc33e31a57cff7df25c3a0 ]

Right now the only user of reset-imx7 is pci-imx6 and the
reset_control_assert and deassert calls on pciephy_reset don't toggle
the PCIEPHY_BTN and PCIEPHY_G_RST bits as expected. Fix this by writing
1 or 0 respectively.

The reference manual is not very clear regarding SRC_PCIEPHY_RCR but for
other registers like MIPIPHY and HSICPHY the bits are explicitly
documented as "1 means assert, 0 means deassert".

The values are still reversed for IMX7_RESET_PCIE_CTRL_APPS_EN.

Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: fix possible spectre-v1 write in ptrace_hbp_set_event()

[ Upstream commit 14d6e289a89780377f8bb09de8926d3c62d763cd ]

It's possible for userspace to control idx. Sanitize idx when using it
as an array index, to inhibit the potential spectre-v1 write gadget.

Found by smatch.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wan/fsl_ucc_hdlc: use IS_ERR_VALUE() to check return value of qe_muram_alloc

[ Upstream commit fd800f646402c0f85547166b59ca065175928b7b ]

qe_muram_alloc return a unsigned long integer,which should not
compared with zero. check it using IS_ERR_VALUE() to fix this.

Fixes: c19b6d246a35 ("drivers/net: support hdlc function for QE-UCC")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Smack: Fix handling of IPv4 traffic received by PF_INET6 sockets

[ Upstream commit 129a99890936766f4b69b9da7ed88366313a9210 ]

A socket which has sk_family set to PF_INET6 is able to receive not
only IPv6 but also IPv4 traffic (IPv4-mapped IPv6 addresses).

Prior to this patch, the smk_skb_to_addr_ipv6() could have been
called for socket buffers containing IPv4 packets, in result such
traffic was allowed.

Signed-off-by: Piotr Sawicki <p.sawicki2@partner.samsung.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: restrict delayed tailroom needed decrement

[ Upstream commit 133bf90dbb8b873286f8ec2e81ba26e863114b8c ]

As explained in ieee80211_delayed_tailroom_dec(), during roam,
keys of the old AP will be destroyed and new keys will be
installed. Deletion of the old key causes
crypto_tx_tailroom_needed_cnt to go from 1 to 0 and the new key
installation causes a transition from 0 to 1.

Whenever crypto_tx_tailroom_needed_cnt transitions from 0 to 1,
we invoke synchronize_net(); the reason for doing this is to avoid
a race in the TX path as explained in increment_tailroom_need_count().
This synchronize_net() operation can be slow and can affect the station
roam time. To avoid this, decrementing the crypto_tx_tailroom_needed_cnt
is delayed for a while so that upon installation of new key the
transition would be from 1 to 2 instead of 0 to 1 and thereby
improving the roam time.

This is all correct for a STA iftype, but deferring the tailroom_needed
decrement for other iftypes may be unnecessary.

For example, let's consider the case of a 4-addr client connecting to
an AP for which AP_VLAN interface is also created, let the initial
value for tailroom_needed on the AP be 1.

* 4-addr client connects to the AP (AP: tailroom_needed = 1)
* AP will clear old keys, delay decrement of tailroom_needed count
* AP_VLAN is created, it takes the tailroom count from master
  (AP_VLAN: tailroom_needed = 1, AP: tailroom_needed = 1)
* Install new key for the station, assume key is plumbed in the HW,
  there won't be any change in tailroom_needed count on AP iface
* Delayed decrement of tailroom_needed count on AP
  (AP: tailroom_needed = 0, AP_VLAN: tailroom_needed = 1)

Because of the delayed decrement on AP iface, tailroom_needed count goes
out of sync between AP(master iface) and AP_VLAN(slave iface) and
there would be unnecessary tailroom created for the packets going
through AP_VLAN iface.

Also, WARN_ONs were observed while trying to bring down the AP_VLAN
interface:
(warn_slowpath_common) (warn_slowpath_null+0x18/0x20)
(warn_slowpath_null) (ieee80211_free_keys+0x114/0x1e4)
(ieee80211_free_keys) (ieee80211_del_virtual_monitor+0x51c/0x850)
(ieee80211_del_virtual_monitor) (ieee80211_stop+0x30/0x3c)
(ieee80211_stop) (__dev_close_many+0x94/0xb8)
(__dev_close_many) (dev_close_many+0x5c/0xc8)

Restricting delayed decrement to station interface alone fixes the problem
and it makes sense to do so because delayed decrement is done to improve
roam time which is applicable only for client devices.

Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: jz4740: Bump zload address

[ Upstream commit c6ea7e9747318e5a6774995f4f8e3e0f7c0fa8ba ]

Having the zload address at 0x8060.0000 means the size of the
uncompressed kernel cannot be bigger than around 6 MiB, as it is
deflated at address 0x8001.0000.

This limit is too small; a kernel with some built-in drivers and things
like debugfs enabled will already be over 6 MiB in size, and so will
fail to extract properly.

To fix this, we bump the zload address from 0x8060.0000 to 0x8100.0000.

This is fine, as all the boards featuring Ingenic JZ SoCs have at least
32 MiB of RAM, and use u-boot or compatible bootloaders which won't
hardcode the load address but read it from the uImage's header.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19787/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: rt5514: Fix the issue of the delay volume applied

[ Upstream commit d96f8bd28cd0bae3e6702ae90df593628ef6906f ]

The patch fixes the issue of the delay volume applied.

Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: handle wait_for_completion_timeout return properly

[ Upstream commit 5b70084f6cbcd53f615433f9d216e01bd71de0bb ]

wait_for_completion_timeout returns unsigned long not int so a variable of
proper type is introduced. Further the check for <= 0 is ambiguous and
should be == 0 here indicating timeout.

Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 7b3ad5abf027 ("staging: Import the BCM2835 MMAL-based V4L2 camera driver.")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: fix timeout handling in wait_for_completion_timeout

[ Upstream commit b7afce51d95726a619743aaad8870db66dfa1479 ]

wait_for_completion_timeout returns unsigned long not int so a variable of
proper type is introduced. Further the check for <= 0 is ambiguous and should
be == 0 here indicating timeout which is the only error case so no additional
check needed here.

Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 7b3ad5abf027 ("staging: Import the BCM2835 MMAL-based V4L2 camera driver.")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/powernv: opal_put_chars partial write fix

[ Upstream commit bd90284cc6c1c9e8e48c8eadd0c79574fcce0b81 ]

The intention here is to consume and discard the remaining buffer
upon error. This works if there has not been a previous partial write.
If there has been, then total_len is no longer total number of bytes
to copy. total_len is always "bytes left to copy", so it should be
added to written bytes.

This code may not be exercised any more if partial writes will not be
hit, but this is a small bugfix before a larger change.

Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: arm/arm64: vgic: Fix possible spectre-v1 write in vgic_mmio_write_apr()

[ Upstream commit 6b8b9a48545e08345b8ff77c9fd51b1aebdbefb3 ]

It's possible for userspace to control n. Sanitize n when using it as an
array index, to inhibit the potential spectre-v1 write gadget.

Note that while it appears that n must be bound to the interval [0,3]
due to the way it is extracted from addr, we cannot guarantee that
compiler transformations (and/or future refactoring) will ensure this is
the case, and given this is a slow path it's better to always perform
the masking.

Found by smatch.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Christoffer Dall <christoffer.dall@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: kvmarm@lists.cs.columbia.edu
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvme-rdma: unquiesce queues when deleting the controller

[ Upstream commit 90140624e8face94207003ac9a9d2a329b309d68 ]

If the controller is going away, we need to unquiesce the IO queues so
that all pending request can fail gracefully before moving forward with
controller deletion. Do that before we destroy the IO queues so
blk_cleanup_queue won't block in freeze.

Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf powerpc: Fix callchain ip filtering

[ Upstream commit c715fcfda5a08edabaa15508742be926b7ee51db ]

For powerpc64, redundant entries in the callchain are filtered out by
determining the state of the return address and the stack frame using
DWARF debug information.

For making these filtering decisions we must analyze the debug
information for the location corresponding to the program counter value,
i.e. the first entry in the callchain, and not the LR value; otherwise,
perf may filter out either the second or the third entry in the
callchain incorrectly.

This can be observed on a powerpc64le system running Fedora 27 as shown
below.

Case 1 - Attaching a probe at inet_pton+0x8 (binary offset 0x15af28).
         Return address is still in LR and a new stack frame is not yet
         allocated. The LR value, i.e. the second entry, should not be
 filtered out.

  # objdump -d /usr/lib64/libc-2.26.so | less
  ...
  000000000010eb10 <gaih_inet.constprop.7>:
  ...
    10fa48:       78 bb e4 7e     mr      r4,r23
    10fa4c:       0a 00 60 38     li      r3,10
    10fa50:       d9 b4 04 48     bl      15af28 <inet_pton+0x8>
    10fa54:       00 00 00 60     nop
    10fa58:       ac f4 ff 4b     b       10ef04 <gaih_inet.constprop.7+0x3f4>
  ...
  0000000000110450 <getaddrinfo>:
  ...
    1105a8:       54 00 ff 38     addi    r7,r31,84
    1105ac:       58 00 df 38     addi    r6,r31,88
    1105b0:       69 e5 ff 4b     bl      10eb18 <gaih_inet.constprop.7+0x8>
    1105b4:       78 1b 71 7c     mr      r17,r3
    1105b8:       50 01 7f e8     ld      r3,336(r31)
  ...
  000000000015af20 <inet_pton>:
    15af20:       0b 00 4c 3c     addis   r2,r12,11
    15af24:       e0 c1 42 38     addi    r2,r2,-15904
    15af28:       a6 02 08 7c     mflr    r0
    15af2c:       f0 ff c1 fb     std     r30,-16(r1)
    15af30:       f8 ff e1 fb     std     r31,-8(r1)
  ...

  # perf probe -x /usr/lib64/libc-2.26.so -a inet_pton+0x8
  # perf record -e probe_libc:inet_pton -g ping -6 -c 1 ::1
  # perf script

Before:

  ping  4507 [002] 514985.546540: probe_libc:inet_pton: (7fffa7dbaf28)
              7fffa7dbaf28 __GI___inet_pton+0x8 (/usr/lib64/libc-2.26.so)
              7fffa7d705b4 getaddrinfo+0x164 (/usr/lib64/libc-2.26.so)
                 13fb52d70 _init+0xbfc (/usr/bin/ping)
              7fffa7c836a0 generic_start_main.isra.0+0x140 (/usr/lib64/libc-2.26.so)
              7fffa7c83898 __libc_start_main+0xb8 (/usr/lib64/libc-2.26.so)
                         0 [unknown] ([unknown])

After:

  ping  4507 [002] 514985.546540: probe_libc:inet_pton: (7fffa7dbaf28)
              7fffa7dbaf28 __GI___inet_pton+0x8 (/usr/lib64/libc-2.26.so)
              7fffa7d6fa54 gaih_inet.constprop.7+0xf44 (/usr/lib64/libc-2.26.so)
              7fffa7d705b4 getaddrinfo+0x164 (/usr/lib64/libc-2.26.so)
                 13fb52d70 _init+0xbfc (/usr/bin/ping)
              7fffa7c836a0 generic_start_main.isra.0+0x140 (/usr/lib64/libc-2.26.so)
              7fffa7c83898 __libc_start_main+0xb8 (/usr/lib64/libc-2.26.so)
                         0 [unknown] ([unknown])

Case 2 - Attaching a probe at _int_malloc+0x180 (binary offset 0x9cf10).
         Return address in still in LR and a new stack frame has already
         been allocated but not used. The caller's caller, i.e. the third
 entry, is invalid and should be filtered out and not the second
 one.

  # objdump -d /usr/lib64/libc-2.26.so | less
  ...
  000000000009cd90 <_int_malloc>:
     9cd90:       17 00 4c 3c     addis   r2,r12,23
     9cd94:       70 a3 42 38     addi    r2,r2,-23696
     9cd98:       26 00 80 7d     mfcr    r12
     9cd9c:       f8 ff e1 fb     std     r31,-8(r1)
     9cda0:       17 00 e4 3b     addi    r31,r4,23
     9cda4:       d8 ff 61 fb     std     r27,-40(r1)
     9cda8:       78 23 9b 7c     mr      r27,r4
     9cdac:       1f 00 bf 2b     cmpldi  cr7,r31,31
     9cdb0:       f0 ff c1 fb     std     r30,-16(r1)
     9cdb4:       b0 ff c1 fa     std     r22,-80(r1)
     9cdb8:       78 1b 7e 7c     mr      r30,r3
     9cdbc:       08 00 81 91     stw     r12,8(r1)
     9cdc0:       11 ff 21 f8     stdu    r1,-240(r1)
     9cdc4:       4c 01 9d 41     bgt     cr7,9cf10 <_int_malloc+0x180>
     9cdc8:       20 00 a4 2b     cmpldi  cr7,r4,32
  ...
     9cf08:       00 00 00 60     nop
     9cf0c:       00 00 42 60     ori     r2,r2,0
     9cf10:       e4 06 ff 7b     rldicr  r31,r31,0,59
     9cf14:       40 f8 a4 7f     cmpld   cr7,r4,r31
     9cf18:       68 05 9d 41     bgt     cr7,9d480 <_int_malloc+0x6f0>
  ...
  000000000009e3c0 <tcache_init.part.4>:
  ...
     9e420:       40 02 80 38     li      r4,576
     9e424:       78 fb e3 7f     mr      r3,r31
     9e428:       71 e9 ff 4b     bl      9cd98 <_int_malloc+0x8>
     9e42c:       00 00 a3 2f     cmpdi   cr7,r3,0
     9e430:       78 1b 7e 7c     mr      r30,r3
  ...
  000000000009f7a0 <__libc_malloc>:
  ...
     9f8f8:       00 00 89 2f     cmpwi   cr7,r9,0
     9f8fc:       1c ff 9e 40     bne     cr7,9f818 <__libc_malloc+0x78>
     9f900:       c9 ea ff 4b     bl      9e3c8 <tcache_init.part.4+0x8>
     9f904:       00 00 00 60     nop
     9f908:       e8 90 22 e9     ld      r9,-28440(r2)
  ...

  # perf probe -x /usr/lib64/libc-2.26.so -a _int_malloc+0x180
  # perf record -e probe_libc:_int_malloc -g ./test-malloc
  # perf script

Before:

  test-malloc  6554 [009] 515975.797403: probe_libc:_int_malloc: (7fffa6e6cf10)
              7fffa6e6cf10 _int_malloc+0x180 (/usr/lib64/libc-2.26.so)
              7fffa6dd0000 [unknown] (/usr/lib64/libc-2.26.so)
              7fffa6e6f904 malloc+0x164 (/usr/lib64/libc-2.26.so)
              7fffa6e6f9fc malloc+0x25c (/usr/lib64/libc-2.26.so)
                  100006b4 main+0x38 (/home/testuser/test-malloc)
              7fffa6df36a0 generic_start_main.isra.0+0x140 (/usr/lib64/libc-2.26.so)
              7fffa6df3898 __libc_start_main+0xb8 (/usr/lib64/libc-2.26.so)
                         0 [unknown] ([unknown])

After:

  test-malloc  6554 [009] 515975.797403: probe_libc:_int_malloc: (7fffa6e6cf10)
              7fffa6e6cf10 _int_malloc+0x180 (/usr/lib64/libc-2.26.so)
              7fffa6e6e42c tcache_init.part.4+0x6c (/usr/lib64/libc-2.26.so)
              7fffa6e6f904 malloc+0x164 (/usr/lib64/libc-2.26.so)
              7fffa6e6f9fc malloc+0x25c (/usr/lib64/libc-2.26.so)
                  100006b4 main+0x38 (/home/sandipan/test-malloc)
              7fffa6df36a0 generic_start_main.isra.0+0x140 (/usr/lib64/libc-2.26.so)
              7fffa6df3898 __libc_start_main+0xb8 (/usr/lib64/libc-2.26.so)
                         0 [unknown] ([unknown])

Signed-off-by: Sandipan Das <sandipan@linux.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Maynard Johnson <maynard@us.ibm.com>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Fixes: a60335ba3298 ("perf tools powerpc: Adjust callchain based on DWARF debug info")
Link: http://lkml.kernel.org/r/24bb726d91ed173aebc972ec3f41a2ef2249434e.1530724939.git.sandipan@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: exynos: Clear global variable on init error path

[ Upstream commit cd4806911cee3901bc2b5eb95603cf1958720b57 ]

For most of Exynos SoCs, Power Management Unit (PMU) address space is
mapped into global variable 'pmu_base_addr' very early when initializing
PMU interrupt controller.  A lot of other machine code depends on it so
when doing iounmap() on this address, clear the global as well to avoid
usage of invalid value (pointing to unmapped memory region).

Properly mapped PMU address space is a requirement for all other machine
code so this fix is purely theoretical.  Boot will fail immediately in
many other places after following this error path.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fbdev: Distinguish between interlaced and progressive modes

[ Upstream commit 1ba0a59cea41ea05fda92daaf2a2958a2246b9cf ]

I discovered the problem when developing a frame buffer driver for the
PlayStation 2 (not yet merged), using the following video modes for the
PlayStation 3 in drivers/video/fbdev/ps3fb.c:

    }, {
        /* 1080if */
        "1080if", 50, 1920, 1080, 13468, 148, 484, 36, 4, 88, 5,
        FB_SYNC_BROADCAST, FB_VMODE_INTERLACED
    }, {
        /* 1080pf */
        "1080pf", 50, 1920, 1080, 6734, 148, 484, 36, 4, 88, 5,
        FB_SYNC_BROADCAST, FB_VMODE_NONINTERLACED
    },

In ps3fb_probe, the mode_option module parameter is used with fb_find_mode
but it can only select the interlaced variant of 1920x1080 since the loop
matching the modes does not take the difference between interlaced and
progressive modes into account.

In short, without the patch, progressive 1920x1080 cannot be chosen as a
mode_option parameter since fb_find_mode (falsely) thinks interlace is a
perfect match.

Signed-off-by: Fredrik Noring <noring@nocrew.org>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
[b.zolnierkie: updated patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

video: fbdev: pxafb: clear allocated memory for video modes

[ Upstream commit b951d80aaf224b1f774e10def672f5e37488e4ee ]

When parsing the video modes from DT properties, make sure to zero out
memory before using it. This is important because not all fields in the mode
struct are explicitly initialized, even though they are used later on.

Fixes: 420a488278e86 ("video: fbdev: pxafb: initial devicetree conversion")
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf powerpc: Fix callchain ip filtering when return address is in a register

[ Upstream commit 9068533e4f470daf2b0f29c71d865990acd8826e ]

For powerpc64, perf will filter out the second entry in the callchain,
i.e. the LR value, if the return address of the function corresponding
to the probed location has already been saved on its caller's stack.

The state of the return address is determined using debug information.
At any point within a function, if the return address is already saved
somewhere, a DWARF expression can tell us about its location. If the
return address in still in LR only, no DWARF expression would exist.

Typically, the instructions in a function's prologue first copy the LR
value to R0 and then pushes R0 on to the stack. If LR has already been
copied to R0 but R0 is yet to be pushed to the stack, we can still get a
DWARF expression that says that the return address is in R0. This is
indicating that getting a DWARF expression for the return address does
not guarantee the fact that it has already been saved on the stack.

This can be observed on a powerpc64le system running Fedora 27 as shown
below.

  # objdump -d /usr/lib64/libc-2.26.so | less
  ...
  000000000015af20 <inet_pton>:
    15af20:       0b 00 4c 3c     addis   r2,r12,11
    15af24:       e0 c1 42 38     addi    r2,r2,-15904
    15af28:       a6 02 08 7c     mflr    r0
    15af2c:       f0 ff c1 fb     std     r30,-16(r1)
    15af30:       f8 ff e1 fb     std     r31,-8(r1)
    15af34:       78 1b 7f 7c     mr      r31,r3
    15af38:       78 23 83 7c     mr      r3,r4
    15af3c:       78 2b be 7c     mr      r30,r5
    15af40:       10 00 01 f8     std     r0,16(r1)
    15af44:       c1 ff 21 f8     stdu    r1,-64(r1)
    15af48:       28 00 81 f8     std     r4,40(r1)
  ...

  # readelf --debug-dump=frames-interp /usr/lib64/libc-2.26.so | less
  ...
  00027024 0000000000000024 00027028 FDE cie=00000000 pc=000000000015af20..000000000015af88
     LOC           CFA      r30   r31   ra
  000000000015af20 r1+0     u     u     u
  000000000015af34 r1+0     c-16  c-8   r0
  000000000015af48 r1+64    c-16  c-8   c+16
  000000000015af5c r1+0     c-16  c-8   c+16
  000000000015af78 r1+0     u     u
  ...

  # perf probe -x /usr/lib64/libc-2.26.so -a inet_pton+0x18
  # perf record -e probe_libc:inet_pton -g ping -6 -c 1 ::1
  # perf script

Before:

  ping  2829 [005] 512917.460174: probe_libc:inet_pton: (7fff7e2baf38)
              7fff7e2baf38 __GI___inet_pton+0x18 (/usr/lib64/libc-2.26.so)
              7fff7e2705b4 getaddrinfo+0x164 (/usr/lib64/libc-2.26.so)
                 12f152d70 _init+0xbfc (/usr/bin/ping)
              7fff7e1836a0 generic_start_main.isra.0+0x140 (/usr/lib64/libc-2.26.so)
              7fff7e183898 __libc_start_main+0xb8 (/usr/lib64/libc-2.26.so)
                         0 [unknown] ([unknown])

After:

  ping  2829 [005] 512917.460174: probe_libc:inet_pton: (7fff7e2baf38)
              7fff7e2baf38 __GI___inet_pton+0x18 (/usr/lib64/libc-2.26.so)
              7fff7e26fa54 gaih_inet.constprop.7+0xf44 (/usr/lib64/libc-2.26.so)
              7fff7e2705b4 getaddrinfo+0x164 (/usr/lib64/libc-2.26.so)
                 12f152d70 _init+0xbfc (/usr/bin/ping)
              7fff7e1836a0 generic_start_main.isra.0+0x140 (/usr/lib64/libc-2.26.so)
              7fff7e183898 __libc_start_main+0xb8 (/usr/lib64/libc-2.26.so)
                         0 [unknown] ([unknown])

Reported-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Sandipan Das <sandipan@linux.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Maynard Johnson <maynard@us.ibm.com>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/66e848a7bdf2d43b39210a705ff6d828a0865661.1530724939.git.sandipan@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fbdev/via: fix defined but not used warning

[ Upstream commit b6566b47a67e07fdca44cf51abb14e2fbe17d3eb ]

Fix a build warning in viafbdev.c when CONFIG_PROC_FS is not enabled
by marking the unused function as __maybe_unused.

../drivers/video/fbdev/via/viafbdev.c:1471:12: warning: 'viafb_sup_odev_proc_show' defined but not used [-Wunused-function]

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

video: goldfishfb: fix memory leak on driver remove

[ Upstream commit 5958fde72d04e7b8c6de3669d1f794a90997e3eb ]

goldfish_fb_probe() allocates memory for fb, but goldfish_fb_remove() does
not have deallocation of fb, which leads to memory leak on probe/remove.

The patch adds deallocation into goldfish_fb_remove().

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Cc: Aleksandar Markovic <aleksandar.markovic@mips.com>
Cc: Miodrag Dinic <miodrag.dinic@mips.com>
Cc: Goran Ferenc <goran.ferenc@mips.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf tools: Fix struct comm_str removal crash

[ Upstream commit 46b3722cc7765582354488da633aafffcb138458 ]

We occasionaly hit following assert failure in 'perf top', when processing the
/proc info in multiple threads.

  perf: ...include/linux/refcount.h:109: refcount_inc:
        Assertion `!(!refcount_inc_not_zero(r))' failed.

The gdb backtrace looks like this:

  [Switching to Thread 0x7ffff11ba700 (LWP 13749)]
  0x00007ffff50839fb in raise () from /lib64/libc.so.6
  (gdb)
  #0  0x00007ffff50839fb in raise () from /lib64/libc.so.6
  #1  0x00007ffff5085800 in abort () from /lib64/libc.so.6
  #2  0x00007ffff507c0da in __assert_fail_base () from /lib64/libc.so.6
  #3  0x00007ffff507c152 in __assert_fail () from /lib64/libc.so.6
  #4  0x0000000000535373 in refcount_inc (r=0x7fffdc009be0)
      at ...include/linux/refcount.h:109
  #5  0x00000000005354f1 in comm_str__get (cs=0x7fffdc009bc0)
      at util/comm.c:24
  #6  0x00000000005356bd in __comm_str__findnew (str=0x7fffd000b260 ":2",
      root=0xbed5c0 <comm_str_root>) at util/comm.c:72
  #7  0x000000000053579e in comm_str__findnew (str=0x7fffd000b260 ":2",
      root=0xbed5c0 <comm_str_root>) at util/comm.c:95
  #8  0x000000000053582e in comm__new (str=0x7fffd000b260 ":2",
      timestamp=0, exec=false) at util/comm.c:111
  #9  0x00000000005363bc in thread__new (pid=2, tid=2) at util/thread.c:57
  #10 0x0000000000523da0 in ____machine__findnew_thread (machine=0xbfde38,
      threads=0xbfdf28, pid=2, tid=2, create=true) at util/machine.c:457
  #11 0x0000000000523eb4 in __machine__findnew_thread (machine=0xbfde38,
  ...

The failing assertion is this one:

  REFCOUNT_WARN(!refcount_inc_not_zero(r), ...

The problem is that we keep global comm_str_root list, which
is accessed by multiple threads during the 'perf top' startup
and following 2 paths can race:

  thread 1:
    ...
    thread__new
      comm__new
        comm_str__findnew
          down_write(&comm_str_lock);
          __comm_str__findnew
            comm_str__get

  thread 2:
    ...
    comm__override or comm__free
      comm_str__put
        refcount_dec_and_test
          down_write(&comm_str_lock);
          rb_erase(&cs->rb_node, &comm_str_root);

Because thread 2 first decrements the refcnt and only after then it removes the
struct comm_str from the list, the thread 1 can find this object on the list
with refcnt equls to 0 and hit the assert.

This patch fixes the thread 1 __comm_str__findnew path, by ignoring objects
that already dropped the refcnt to 0. For the rest of the objects we take the
refcnt before comparing its name and release it afterwards with comm_str__put,
which can also release the object completely.

Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Lukasz Odzioba <lukasz.odzioba@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: kernel-team@lge.com
Link: http://lkml.kernel.org/r/20180720101740.GA27176@krava
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fbdev: omapfb: off by one in omapfb_register_client()

[ Upstream commit 5ec1ec35b2979b59d0b33381e7c9aac17e159d16 ]

The omapfb_register_client[] array has OMAPFB_PLANE_NUM elements so the
> should be >= or we are one element beyond the end of the array.

Fixes: 8b08cf2b64f5 ("OMAP: add TI OMAP framebuffer driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf tools: Synthesize GROUP_DESC feature in pipe mode

[ Upstream commit e8fedff1cc729fd227924305152ccc6f580e8c83 ]

Stephan reported, that pipe mode does not carry the group information
and thus the piped report won't display the grouped output for following
command:

  # perf record -e '{cycles,instructions,branches}' -a sleep 4 | perf report

It has no idea about the group setup, so it will display events
separately:

  # Overhead  Command          Shared Object             ...
  # ........  ...............  .......................
  #
       6.71%  swapper          [kernel.kallsyms]
       2.28%  offlineimap      libpython2.7.so.1.0
       0.78%  perf             [kernel.kallsyms]
  ...

Fix GROUP_DESC feature record to be synthesized in pipe mode, so the
report output is grouped if there are groups defined in record:

  #                 Overhead  Command          Shared    ...
  # ........................  ...............  .......
  #
       7.57%   0.16%   0.30%  swapper          [kernel
       1.87%   3.15%   2.46%  offlineimap      libpyth
       1.33%   0.00%   0.00%  perf             [kernel
  ...

Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tested-by: Stephane Eranian <eranian@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: David Carrillo-Cisneros <davidcc@google.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180712135202.14774-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gfs2: Don't reject a supposedly full bitmap if we have blocks reserved

[ Upstream commit e79e0e1428188b24c3b57309ffa54a33c4ae40c4 ]

Before this patch, you could get into situations like this:

1. Process 1 searches for X free blocks, finds them, makes a reservation
2. Process 2 searches for free blocks in the same rgrp, but now the
   bitmap is full because process 1's reservation is skipped over.
   So it marks the bitmap as GBF_FULL.
3. Process 1 tries to allocate blocks from its own reservation, but
   since the GBF_FULL bit is set, it skips over the rgrp and searches
   elsewhere, thus not using its own reservation.

This patch adds an additional check to allow processes to use their
own reservations.

Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf test: Fix subtest number when showing results

[ Upstream commit 9ef0112442bdddef5fb55adf20b3a5464b33de75 ]

Perf test 40 for example has several subtests numbered 1-4 when
displaying the start of the subtest. When the subtest results
are displayed the subtests are numbered 0-3.

Use this command to generate trace output:

  [root@s35lp76 perf]# ./perf test -Fv 40 2>/tmp/bpf1

Fix this by adjusting the subtest number when show the
subtest result.

Output before:

  [root@s35lp76 perf]# egrep '(^40\.[0-4]| subtest [0-4]:)' /tmp/bpf1
  40.1: Basic BPF filtering                                 :
  BPF filter subtest 0: Ok
  40.2: BPF pinning                                         :
  BPF filter subtest 1: Ok
  40.3: BPF prologue generation                             :
  BPF filter subtest 2: Ok
  40.4: BPF relocation checker                              :
  BPF filter subtest 3: Ok
  [root@s35lp76 perf]#

Output after:

  root@s35lp76 ~]# egrep '(^40\.[0-4]| subtest [0-4]:)' /tmp/bpf1
  40.1: Basic BPF filtering                                 :
  BPF filter subtest 1: Ok
  40.2: BPF pinning                                         :
  BPF filter subtest 2: Ok
  40.3: BPF prologue generation                             :
  BPF filter subtest 3: Ok
  40.4: BPF relocation checker                              :
  BPF filter subtest 4: Ok
  [root@s35lp76 ~]#

Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Link: http://lkml.kernel.org/r/20180724134858.100644-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: ov5645: Supported external clock is 24MHz

[ Upstream commit 4adb0a0432f489c5eb802b33dae7737f69e6fd7a ]

The external clock frequency was set to 23.88MHz by mistake
because of a platform which cannot get closer to 24MHz.
The supported by the driver external clock is 24MHz so
set it correctly and also fix the values of the pixel
clock and link clock.
However allow 1% tolerance to the external clock as this
difference is small enough to be insignificant.

Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd/maps: fix solutionengine.c printk format warnings

[ Upstream commit 1d25e3eeed1d987404e2d2e451eebac8c15cecc1 ]

Fix 2 printk format warnings (this driver is currently only used by
arch/sh/) by using "%pap" instead of "%lx".

Fixes these build warnings:

../drivers/mtd/maps/solutionengine.c: In function 'init_soleng_maps':
../include/linux/kern_levels.h:5:18: warning: format '%lx' expects argument of type 'long unsigned int', but argument 2 has type 'resource_size_t' {aka 'unsigned int'} [-Wformat=]
../drivers/mtd/maps/solutionengine.c:62:54: note: format string is defined here
  printk(KERN_NOTICE "Solution Engine: Flash at 0x%08lx, EPROM at 0x%08lx\n",
                                                  ~~~~^
                                                  %08x
../include/linux/kern_levels.h:5:18: warning: format '%lx' expects argument of type 'long unsigned int', but argument 3 has type 'resource_size_t' {aka 'unsigned int'} [-Wformat=]
../drivers/mtd/maps/solutionengine.c:62:72: note: format string is defined here
  printk(KERN_NOTICE "Solution Engine: Flash at 0x%08lx, EPROM at 0x%08lx\n",
                                                                    ~~~~^
                                                                    %08x

Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: linux-mtd@lists.infradead.org
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: linux-sh@vger.kernel.org
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/ipoib: Fix error return code in ipoib_dev_init()

[ Upstream commit 99a7e2bf704d64c966dfacede1ba2d9b47cb676e ]

Fix to return a negative error code from the ipoib_neigh_hash_init()
error handling case instead of 0, as done elsewhere in this function.

Fixes: 515ed4f3aab4 ("IB/IPoIB: Separate control and data related initializations")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block: allow max_discard_segments to be stacked

[ Upstream commit 42c9cdfe1e11e083dceb0f0c4977b758cf7403b9 ]

Set max_discard_segments to USHRT_MAX in blk_set_stacking_limits() so
that blk_stack_limits() can stack up this limit for stacked devices.

before:

$ cat /sys/block/nvme0n1/queue/max_discard_segments
256
$ cat /sys/block/dm-0/queue/max_discard_segments
1

after:

$ cat /sys/block/nvme0n1/queue/max_discard_segments
256
$ cat /sys/block/dm-0/queue/max_discard_segments
256

Fixes: 1e739730c5b9e ("block: optionally merge discontiguous discard bios into a single request")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/rxe: Drop QP0 silently

[ Upstream commit 536ca245c512aedfd84cde072d7b3ca14b6e1792 ]

According to "Annex A16: RDMA over Converged Ethernet (RoCE)":

A16.4.3 MANAGEMENT INTERFACES

As defined in the base specification, a special Queue Pair, QP0 is defined
solely for communication between subnet manager(s) and subnet management
agents. Since such an IB-defined subnet management architecture is outside
the scope of this annex, it follows that there is also no requirement that
a port which conforms to this annex be associated with a QP0. Thus, for
end nodes designed to conform to this annex, the concept of QP0 is
undefined and unused for any port connected to an Ethernet network.

CA16-8: A packet arriving at a RoCE port containing a BTH with the
destination QP field set to QP0 shall be silently dropped.

Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: videobuf2-core: check for q->error in vb2_core_qbuf()

[ Upstream commit b509d733d337417bcb7fa4a35be3b9a49332b724 ]

The vb2_core_qbuf() function didn't check if q->error was set. It is
checked in __buf_prepare(), but that function isn't called if the buffer
was already prepared before with VIDIOC_PREPARE_BUF.

So check it at the start of vb2_core_qbuf() as well.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: ath79: fix system restart

[ Upstream commit f8a7bfe1cb2c1ebfa07775c9c8ac0ad3ba8e5ff5 ]

This patch disables irq on reboot to fix hang issues that were observed
due to pending interrupts.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19913/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dmaengine: pl330: fix irq race with terminate_all

[ Upstream commit e49756544a21f5625b379b3871d27d8500764670 ]

In pl330_update() when checking if a channel has been aborted, the
channel's lock is not taken, only the overall pl330_dmac lock.  But in
pl330_terminate_all() the aborted flag (req_running==-1) is set under
the channel lock and not the pl330_dmac lock.

With threaded interrupts, this leads to a potential race:

    pl330_terminate_all         pl330_update
    -------------------         ------------
    lock channel
                                entry
    lock pl330
    _stop channel
    unlock pl330
                                lock pl330
                                check req_running != -1
    req_running = -1
                                _start channel

Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: tw686x: Fix oops on buffer alloc failure

[ Upstream commit 5a1a2f63d840dc2631505b607e11ff65ac1b7d3c ]

The error path currently calls tw686x_video_free() which requires
vc->dev to be initialized, causing a NULL dereference on uninitizalized
channels.

Fix this by setting the vc->dev fields for all the channels first.

Fixes: f8afaa8dbc0d ("[media] tw686x: Introduce an interface to support multiple DMA modes")

Signed-off-by: Krzysztof Ha?asa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kbuild: add .DELETE_ON_ERROR special target

[ Upstream commit 9c2af1c7377a8a6ef86e5cabf80978f3dbbb25c0 ]

If Make gets a fatal signal while a shell is executing, it may delete
the target file that the recipe was supposed to update.  This is needed
to make sure that it is remade from scratch when Make is next run; if
Make is interrupted after the recipe has begun to write the target file,
it results in an incomplete file whose time stamp is newer than that
of the prerequisites files.  Make automatically deletes the incomplete
file on interrupt unless the target is marked .PRECIOUS.

The situation is just the same as when the shell fails for some reasons.
Usually when a recipe line fails, if it has changed the target file at
all, the file is corrupted, or at least it is not completely updated.
Yet the file’s time stamp says that it is now up to date, so the next
time Make runs, it will not try to update that file.

However, Make does not cater to delete the incomplete target file in
this case.  We need to add .DELETE_ON_ERROR somewhere in the Makefile
to request it.

scripts/Kbuild.include seems a suitable place to add it because it is
included from almost all sub-makes.

Please note .DELETE_ON_ERROR is not effective for phony targets.

The external module building should never ever touch the kernel tree.
The following recipe fails if include/generated/autoconf.h is missing.
However, include/config/auto.conf is not deleted since it is a phony
target.

 PHONY += include/config/auto.conf

 include/config/auto.conf:
         $(Q)test -e include/generated/autoconf.h -a -e $@ || (          \
         echo >&2;                                                       \
         echo >&2 "  ERROR: Kernel configuration is invalid.";           \
         echo >&2 "         include/generated/autoconf.h or $@ are missing.";\
         echo >&2 "         Run 'make oldconfig && make prepare' on kernel src to fix it."; \
         echo >&2 ;                                                      \
         /bin/false)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: clk-fixed-factor: Clear OF_POPULATED flag in case of failure

[ Upstream commit f6dab4233d6b64d719109040503b567f71fbfa01 ]

Fixed factor clock has two initializations at of_clk_init() time
and during platform driver probe. Before of_clk_init() call,
node is marked as populated and so its probe never gets called.

During of_clk_init() fixed factor clock registration may fail if
any of its parent clock is not registered. In this case, it doesn't
get chance to retry registration from probe. Clear OF_POPULATED
flag if fixed factor clock registration fails so that clock
registration is attempted again from probe.

Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: core: Potentially free connection id

[ Upstream commit 365f7a89c881e84f1ebc925f65f899d5d7ce547e ]

Patch "clk: core: Copy connection id" made it so that the connector id
'con_id' is kstrdup_const()ed to cater to drivers that pass non-constant
connection ids. The patch added the corresponding kfree_const to
__clk_free_clk(), but struct clk's can be freed also via __clk_put().
Add the kfree_const call to __clk_put() and add comments to both
functions to remind that the logic in them should be kept in sync.

Fixes: 253160a8ad06 ("clk: core: Copy connection id")
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: imx6ul: fix missing of_node_put()

[ Upstream commit 11177e7a7aaef95935592072985526ebf0a3df43 ]

of_find_compatible_node() is returning a device node with refcount
incremented and must be explicitly decremented after the last use
which is right after the us in of_iomap() here.

Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 787b4271a6a0 ("clk: imx: add imx6ul clk tree support")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gfs2: Special-case rindex for gfs2_grow

[ Upstream commit 776125785a87ff05d49938bd5b9f336f2a05bff6 ]

To speed up the common case of appending to a file,
gfs2_write_alloc_required presumes that writing beyond the end of a file
will always require additional blocks to be allocated.  This assumption
is incorrect for preallocates files, but there are no negative
consequences as long as *some* space is still left on the filesystem.

One special file that always has some space preallocated beyond the end
of the file is the rindex: when growing a filesystem, gfs2_grow adds one
or more new resource groups and appends records describing those
resource groups to the rindex; the preallocated space ensures that this
is always possible.

However, when a filesystem is completely full, gfs2_write_alloc_required
will indicate that an additional allocation is required, and appending
the next record to the rindex will fail even though space for that
record has already been preallocated.  To fix that, skip the incorrect
optimization in gfs2_write_alloc_required, but for the rindex only.
Other writes to preallocated space beyond the end of the file are still
allowed to fail on completely full filesystems.

Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

amd-xgbe: use dma_mapping_error to check map errors

[ Upstream commit b24dbfe9ce03d9f83306616f22fb0e04e8960abe ]

The dma_mapping_error() returns true or false, but we want
to return -ENOMEM if there was an error.

Fixes: 174fd2597b0b ("amd-xgbe: Implement split header receive support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xfrm: fix 'passing zero to ERR_PTR()' warning

[ Upstream commit 934ffce1343f22ed5e2d0bd6da4440f4848074de ]

Fix a static code checker warning:

  net/xfrm/xfrm_policy.c:1836 xfrm_resolve_and_create_bundle() warn: passing zero to 'ERR_PTR'

xfrm_tmpl_resolve return 0 just means no xdst found, return NULL
instead of passing zero to ERR_PTR.

Fixes: d809ec895505 ("xfrm: do not assume that template resolving always returns xfrms")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: usb-audio: Fix multiple definitions in AU0828_DEVICE() macro

[ Upstream commit bd1cd0eb2ce9141100628d476ead4de485501b29 ]

AU0828_DEVICE() macro in quirks-table.h uses USB_DEVICE_VENDOR_SPEC()
for expanding idVendor and idProduct fields.  However, the latter
macro adds also match_flags and bInterfaceClass, which are different
from the values AU0828_DEVICE() macro sets after that.

For fixing them, just expand idVendor and idProduct fields manually in
AU0828_DEVICE().

This fixes sparse warnings like:
  sound/usb/quirks-table.h:2892:1: warning: Initializer entry defined twice

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: msnd: Fix the default sample sizes

[ Upstream commit 7c500f9ea139d0c9b80fdea5a9c911db3166ea54 ]

The default sample sizes set by msnd driver are bogus; it sets ALSA
PCM format, not the actual bit width.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu/io-pgtable-arm-v7s: Abort allocation when table address overflows the PTE

[ Upstream commit 29859aeb8a6ea17ba207933a81b6b77b4d4df81a ]

When run on a 64-bit system in selftest, the v7s driver may obtain page
table with physical addresses larger than 32-bit. Level-2 tables are 1KB
and are are allocated with slab, which doesn't accept the GFP_DMA32
flag. Currently map() truncates the address written in the PTE, causing
iova_to_phys() or unmap() to access invalid memory. Kasan reports it as
a use-after-free. To avoid any nasty surprise, test if the physical
address fits in a PTE before returning a new table. 32-bit systems,
which are the main users of this page table format, shouldn't see any
difference.

Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu/arm-smmu-v3: sync the OVACKFLG to PRIQ consumer register

[ Upstream commit 0d535967ac658966c6ade8f82b5799092f7d5441 ]

When PRI queue occurs overflow, driver should update the OVACKFLG to
the PRIQ consumer register, otherwise subsequent PRI requests will not
be processed.

Cc: Will Deacon <will.deacon@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Miao Zhong <zhongmiao@hisilicon.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: change stream event enable bit back to 13

[ Upstream commit 9a7faac3650216112e034b157289bf1a48a99e2d ]

Commit ff3f0789b3dc ("usb: dwc3: use BIT() macro where possible")
changed DWC3_DEPCFG_STREAM_EVENT_EN from bit 13 to bit 12.

Spotted this cleanup typo while looking at diffs between 4.9.35 and
4.14.16 for a separate issue.

Fixes: ff3f0789b3dc ("usb: dwc3: use BIT() macro where possible")
Signed-off-by: Erich E. Hoover <ehoover@sweptlaser.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>