review.tizen.org Git - platform/kernel/linux-rpi.git/log

Merge branch 'locking-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull lockdep fix from Ingo Molnar:
"This fixes an ugly lockdep stack trace output regression. (But also
affects other stacktrace users such as kmemleak, KASAN, etc)"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
stacktrace, lockdep: Fix address, newline ugliness

Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull irq fixes from Ingo Molnar:
"Two last minute ARM irqchip driver fixes"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mxs: Enable SKIP_SET_WAKE and MASK_ON_SUSPEND
irqchip/keystone: Fix "scheduling while atomic" on rt

Merge branch 'for-linus-4.10' of git://git./linux/kernel/git/mason/linux-btrfs

Pull btrfs fixes from Chris Mason:
"This has two last minute fixes. The highest priority here is a
  regression fix for the decompression code, but we also fixed up a
  problem with the 32-bit compat ioctls.

  The decompression bug could hand back the wrong data on big reads when
  zlib was used. I have a larger cleanup to make the math here less
  error prone, but at this stage in the release Omar's patch is the best
  choice"

* 'for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: fix btrfs_decompress_buf2page()
  btrfs: fix btrfs_compat_ioctl failures on non-compat ioctls

Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi

Pull SCSI fixes from James Bottomley:
"Six fairly small fixes. None is a real show stopper, two automation
  detected problems: one memory leak, one use after free and four others
  each of which fixes something that has been a significant source of
  annoyance to someone"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: zfcp: fix use-after-free by not tracing WKA port open/close on failed send
  scsi: aacraid: Fix INTx/MSI-x issue with older controllers
  scsi: mpt3sas: disable ASPM for MPI2 controllers
  scsi: mpt3sas: Force request partial completion alignment
  scsi: qla2xxx: Avoid that issuing a LIP triggers a kernel crash
  scsi: qla2xxx: Fix a recently introduced memory leak

Btrfs: fix btrfs_decompress_buf2page()

If btrfs_decompress_buf2page() is handed a bio with its page in the
middle of the working buffer, then we adjust the offset into the working
buffer. After we copy into the bio, we advance the iterator by the
number of bytes we copied. Then, we have some logic to handle the case
of discontiguous pages and adjust the offset into the working buffer
again. However, if we didn't advance the bio to a new page, we may enter
this case in error, essentially repeating the adjustment that we already
made when we entered the function. The end result is bogus data in the
bio.

Previously, we only checked for this case when we advanced to a new
page, but the conversion to bio iterators changed that. This restores
the old, correct behavior.

A case I saw when testing with zlib was:

    buf_start = 42769
    total_out = 46865
    working_bytes = total_out - buf_start = 4096
    start_byte = 45056

The condition (total_out > start_byte && buf_start < start_byte) is
true, so we adjust the offset:

    buf_offset = start_byte - buf_start = 2287
    working_bytes -= buf_offset = 1809
    current_buf_start = buf_start = 42769

Then, we copy

    bytes = min(bvec.bv_len, PAGE_SIZE - buf_offset, working_bytes) = 1809
    buf_offset += bytes = 4096
    working_bytes -= bytes = 0
    current_buf_start += bytes = 44578

After bio_advance(), we are still in the same page, so start_byte is the
same. Then, we check (total_out > start_byte && current_buf_start < start_byte),
which is true! So, we adjust the values again:

    buf_offset = start_byte - buf_start = 2287
    working_bytes = total_out - start_byte = 1809
    current_buf_start = buf_start + buf_offset = 45056

But note that working_bytes was already zero before this, so we should
have stopped copying.

Fixes: 974b1adc3b10 ("btrfs: use bio iterators for the decompression handlers")
Reported-by: Pat Erley <pat-lkml@erley.org>
Reviewed-by: Chris Mason <clm@fb.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Tested-by: Liu Bo <bo.li.liu@oracle.com>

Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David Miller:

1) If the timing is wrong we can indefinitely stop generating new ipv6
    temporary addresses, from Marcus Huewe.

2) Don't double free per-cpu stats in ipv6 SIT tunnel driver, from Cong
    Wang.

3) Put protections in place so that AF_PACKET is not able to submit
    packets which don't even have a link level header to drivers. From
    Willem de Bruijn.

4) Fix memory leaks in ipv4 and ipv6 multicast code, from Hangbin Liu.

5) Don't use udp_ioctl() in l2tp code, UDP version expects a UDP socket
    and that doesn't go over very well when it is passed an L2TP one.
    Fix from Eric Dumazet.

6) Don't crash on NULL pointer in phy_attach_direct(), from Florian
    Fainelli.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  l2tp: do not use udp_ioctl()
  xen-netfront: Delete rx_refill_timer in xennet_disconnect_backend()
  NET: mkiss: Fix panic
  net: hns: Fix the device being used for dma mapping during TX
  net: phy: Initialize mdio clock at probe function
  igmp, mld: Fix memory leak in igmpv3/mld_del_delrec()
  xen-netfront: Improve error handling during initialization
  sierra_net: Skip validating irrelevant fields for IDLE LSIs
  sierra_net: Add support for IPv6 and Dual-Stack Link Sense Indications
  kcm: fix 0-length case for kcm_sendmsg()
  xen-netfront: Rework the fix for Rx stall during OOM and network stress
  net: phy: Fix PHY module checks and NULL deref in phy_attach_direct()
  net: thunderx: Fix PHY autoneg for SGMII QLM mode
  net: dsa: Do not destroy invalid network devices
  ping: fix a null pointer dereference
  packet: round up linear to header len
  net: introduce device min_header_len
  sit: fix a double free on error path
  lwtunnel: valid encap attr check should return 0 when lwtunnel is disabled
  ipv6: addrconf: fix generation of new temporary addresses

Merge tag 'for-linus' of git://git./linux/kernel/git/dledford/rdma

Pull rdma fixes from Doug Ledford:
"Third round of -rc fixes for 4.10 kernel:

   - two security related issues in the rxe driver

   - one compile issue in the RDMA uapi header"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
  RDMA: Don't reference kernel private header from UAPI header
  IB/rxe: Fix mem_check_range integer overflow
  IB/rxe: Fix resid update

Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux

Pull i2c bugfixes from Wolfram Sang:
"Two bugfixes (proper IO mapping and use of mutex) for a driver feature
  we introduced in this cycle"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: piix4: Request the SMBUS semaphore inside the mutex
  i2c: piix4: Fix request_region size

Merge tag 'mmc-v4.10-rc7' of git://git./linux/kernel/git/ulfh/mmc

Pull MMC host fix from Ulf Hansson:
"mmci: Fix hang while waiting for busy-end interrupt"

* tag 'mmc-v4.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: mmci: avoid clearing ST Micro busy end interrupt mistakenly

Merge tag 'sound-4.10' of git://git./linux/kernel/git/tiwai/sound

Pull sound fixes from Takashi Iwai:
"Here are some last-minute fixes: two fixes for races in ALSA sequencer
  queue spotted by syzkaller, a revert for a regression of LINE6 driver
  (since 4.9), and a trivial new codec ID addition for Nvidia HDMI"

* tag 'sound-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - adding a new NV HDMI/DP codec ID in the driver
  ALSA: seq: Fix race at creating a queue
  Revert "ALSA: line6: Only determine control port properties if needed"
  ALSA: seq: Don't handle loop timeout at snd_seq_pool_done()

Merge tag 'nfsd-4.10-3' of git://linux-nfs.org/~bfields/linux

Pull nfsd revert from Bruce Fields:
"This patch turned out to have a couple problems. The problems are
  fixable, but at least one of the fixes is a little ugly. The original
  bug has always been there, so we can wait another week or two to get
  this right"

* tag 'nfsd-4.10-3' of git://linux-nfs.org/~bfields/linux:
  nfsd: Revert "nfsd: special case truncates some more"

Merge tag 'powerpc-4.10-4' of git://git./linux/kernel/git/powerpc/linux

Pull powerpc fixes friom Michael Ellerman:
"Apologies for the late pull request, but Ben has been busy finding bugs.

   - Userspace was semi-randomly segfaulting on radix due to us
     incorrectly handling a fault triggered by autonuma, caused by a
     patch we merged earlier in v4.10 to prevent the kernel executing
     userspace.

   - We weren't marking host IPIs properly for KVM in the OPAL ICP
     backend.

   - The ERAT flushing on radix was missing an isync and was incorrectly
     marked as DD1 only.

   - The powernv CPU hotplug code was missing a wakeup type and failing
     to flush the interrupt correctly when using OPAL ICP

  Thanks to Benjamin Herrenschmidt"

* tag 'powerpc-4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/powernv: Properly set "host-ipi" on IPIs
  powerpc/powernv: Fix CPU hotplug to handle waking on HVI
  powerpc/mm/radix: Update ERAT flushes when invalidating TLB
  powerpc/mm: Fix spurrious segfaults on radix with autonuma

l2tp: do not use udp_ioctl()

udp_ioctl(), as its name suggests, is used by UDP protocols,
but is also used by L2TP :(

L2TP should use its own handler, because it really does not
look the same.

SIOCINQ for instance should not assume UDP checksum or headers.

Thanks to Andrey and syzkaller team for providing the report
and a nice reproducer.

While crashes only happen on recent kernels (after commit
7c13f97ffde6 ("udp: do fwd memory scheduling on dequeue")), this
probably needs to be backported to older kernels.

Fixes: 7c13f97ffde6 ("udp: do fwd memory scheduling on dequeue")
Fixes: 85584672012e ("udp: Fix udp_poll() and ioctl()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-chris' of git://git./linux/kernel/git/kdave/linux into for-linus-4.10

xen-netfront: Delete rx_refill_timer in xennet_disconnect_backend()

rx_refill_timer should be deleted as soon as we disconnect from the
backend since otherwise it is possible for the timer to go off before
we get to xennet_destroy_queues(). If this happens we may dereference
queue->rx.sring which is set to NULL in xennet_disconnect_backend().

Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
CC: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NET: mkiss: Fix panic

If a USB-to-serial adapter is unplugged, the driver re-initializes, with
dev->hard_header_len and dev->addr_len set to zero, instead of the correct
values. If then a packet is sent through the half-dead interface, the
kernel will panic due to running out of headroom in the skb when pushing
for the AX.25 headers resulting in this panic:

[<c0595468>] (skb_panic) from [<c0401f70>] (skb_push+0x4c/0x50)
[<c0401f70>] (skb_push) from [<bf0bdad4>] (ax25_hard_header+0x34/0xf4 [ax25])
[<bf0bdad4>] (ax25_hard_header [ax25]) from [<bf0d05d4>] (ax_header+0x38/0x40 [mkiss])
[<bf0d05d4>] (ax_header [mkiss]) from [<c041b584>] (neigh_compat_output+0x8c/0xd8)
[<c041b584>] (neigh_compat_output) from [<c043e7a8>] (ip_finish_output+0x2a0/0x914)
[<c043e7a8>] (ip_finish_output) from [<c043f948>] (ip_output+0xd8/0xf0)
[<c043f948>] (ip_output) from [<c043f04c>] (ip_local_out_sk+0x44/0x48)

This patch makes mkiss behave like the 6pack driver. 6pack does not
panic. In 6pack.c sp_setup() (same function name here) the values for
dev->hard_header_len and dev->addr_len are set to the same values as in
my mkiss patch.

[ralf@linux-mips.org: Massages original submission to conform to the usual
standards for patch submissions.]

Signed-off-by: Thomas Osterried <thomas@osterried.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns: Fix the device being used for dma mapping during TX

This patch fixes the device being used to DMA map skb->data.
Erroneous device assignment causes the crash when SMMU is enabled.
This happens during TX since buffer gets DMA mapped with device
correspondign to net_device and gets unmapped using the device
related to DSAF.

Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'irqchip-fixes-4.10' of git://git.infradead.org/users/jcooper/linux into irq/urgent

Pull irqchip fixes for v4.10 from Jason Cooper

- keystone: Fix scheduling while atomic for realtime
- mxs: Enable SKIP_SET_WAKE and MASK_ON_SUSPEND

Merge remote-tracking branch 'mkp-scsi/4.10/scsi-fixes' into fixes

nfsd: Revert "nfsd: special case truncates some more"

This patch incorrectly attempted nested mnt_want_write, and incorrectly
disabled nfsd's owner override for truncate. We'll fix those problems
and make another attempt soon, for the moment I think the safest is to
revert.

Signed-off-by: J. Bruce Fields <bfields@redhat.com>

Merge tag 'drm-fixes-for-v4.10-rc8' of git://people.freedesktop.org/~airlied/linux

Pull drm fixes from Dave Airlie:
"This should be the final set of drm fixes for 4.10: one vmwgfx boot
  fix, one vc4 fix, and a few i915 fixes:

* tag 'drm-fixes-for-v4.10-rc8' of git://people.freedesktop.org/~airlied/linux:
  drm: vc4: adapt to new behaviour of drm_crtc.c
  drm/i915: Always convert incoming exec offsets to non-canonical
  drm/i915: Remove overzealous fence warn on runtime suspend
  drm/i915/bxt: Add MST support when do DPLL calculation
  drm/i915: don't warn about Skylake CPU - KabyPoint PCH combo
  drm/i915: fix i915 running as dom0 under Xen
  drm/i915: Flush untouched framebuffers before display on !llc
  drm/i915: fix use-after-free in page_flip_completed()
  drm/vmwgfx: Fix depth input into drm_mode_legacy_fb_format

scsi: zfcp: fix use-after-free by not tracing WKA port open/close on failed send

Dan Carpenter kindly reported:
<quote>
The patch d27a7cb91960: "zfcp: trace on request for open and close of
WKA port" from Aug 10, 2016, leads to the following static checker
warning:

drivers/s390/scsi/zfcp_fsf.c:1615 zfcp_fsf_open_wka_port()
warn: 'req' was already freed.

drivers/s390/scsi/zfcp_fsf.c
  1609          zfcp_fsf_start_timer(req, ZFCP_FSF_REQUEST_TIMEOUT);
  1610          retval = zfcp_fsf_req_send(req);
  1611          if (retval)
  1612                  zfcp_fsf_req_free(req);
                                          ^^^
Freed.

  1613  out:
  1614          spin_unlock_irq(&qdio->req_q_lock);
  1615          if (req && !IS_ERR(req))
  1616                  zfcp_dbf_rec_run_wka("fsowp_1", wka_port, req->req_id);
                                                                  ^^^^^^^^^^^
Use after free.

  1617          return retval;
  1618  }

Same thing for zfcp_fsf_close_wka_port() as well.
</quote>

Rather than relying on req being NULL (or ERR_PTR) for all cases where
we don't want to trace or should not trace,
simply check retval which is unconditionally initialized with -EIO != 0
and it can only become 0 on successful retval = zfcp_fsf_req_send(req).
With that we can also remove the then again unnecessary unconditional
initialization of req which was introduced with that earlier commit.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Suggested-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: d27a7cb91960 ("zfcp: trace on request for open and close of WKA port")
Cc: <stable@vger.kernel.org> #2.6.38+
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Fix INTx/MSI-x issue with older controllers

commit 78cbccd3bd68 ("aacraid: Fix for KDUMP driver hang")

caused a problem on older controllers which do not support MSI-x (namely
ASR3405,ASR3805). This patch conditionalizes the previous patch to
controllers which support MSI-x

Cc: <stable@vger.kernel.org> # v4.7+
Fixes: 78cbccd3bd68 ("aacraid: Fix for KDUMP driver hang")
Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Merge tag 'drm-intel-fixes-2017-02-09' of git://anongit.freedesktop.org/git/drm-intel into drm-fixes

Hopefully final fixes for v4.10, about half of them stable material.

* tag 'drm-intel-fixes-2017-02-09' of git://anongit.freedesktop.org/git/drm-intel:
  drm/i915: Always convert incoming exec offsets to non-canonical
  drm/i915: Remove overzealous fence warn on runtime suspend
  drm/i915/bxt: Add MST support when do DPLL calculation
  drm/i915: don't warn about Skylake CPU - KabyPoint PCH combo
  drm/i915: fix i915 running as dom0 under Xen
  drm/i915: Flush untouched framebuffers before display on !llc
  drm/i915: fix use-after-free in page_flip_completed()

Merge tag 'drm-misc-fixes-2017-02-09' of git://anongit.freedesktop.org/git/drm-misc into drm-fixes

Last-minute vc4 fix for 4.10.

* tag 'drm-misc-fixes-2017-02-09' of git://anongit.freedesktop.org/git/drm-misc:
drm: vc4: adapt to new behaviour of drm_crtc.c

scsi: mpt3sas: disable ASPM for MPI2 controllers

MPI2 controllers sometimes got lost (i.e. disappear from
/sys/bus/pci/devices) if ASMP is enabled.

Signed-off-by: Slava Kardakov <ojab@ojab.ru>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=60644
Cc: <stable@vger.kernel.org>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

net: phy: Initialize mdio clock at probe function

USB PHYs need the MDIO clock divisor enabled earlier to work.
Initialize mdio clock divisor in probe function. The ext bus
bit available in the same register will be used by mdio mux
to enable external mdio.

Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Fixes: ddc24ae1 ("net: phy: Broadcom iProc MDIO bus driver")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igmp, mld: Fix memory leak in igmpv3/mld_del_delrec()

In function igmpv3/mld_add_delrec() we allocate pmc and put it in
idev->mc_tomb, so we should free it when we don't need it in del_delrec().
But I removed kfree(pmc) incorrectly in latest two patches. Now fix it.

Fixes: 24803f38a5c0 ("igmp: do not remove igmp souce list info when ...")
Fixes: 1666d49e1d41 ("mld: do not remove mld souce list info when ...")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xen-netfront: Improve error handling during initialization

This fixes a crash when running out of grant refs when creating many
queues across many netdevs.

* If creating queues fails (i.e. there are no grant refs available),
call xenbus_dev_fatal() to ensure that the xenbus device is set to the
closed state.
* If no queues are created, don't call xennet_disconnect_backend as
netdev->real_num_tx_queues will not have been set correctly.
* If setup_netfront() fails, ensure that all the queues created are
cleaned up, not just those that have been set up.
* If any queues were set up and an error occurs, call
xennet_destroy_queues() to clean up the napi context.
* If any fatal error occurs, unregister and destroy the netdev to avoid
leaving around a half setup network device.

Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'sierra_net-fixes'

Stefan Brüns says:

====================
Fixes for sierra_net driver

When trying to initiate a dual-stack (ipv4v6) connection, a MC7710, FW
version SWI9200X_03.05.24.00ap answers with an unsupported LSI. Add support
for this LSI.
Also the link_type should be ignored when going idle, otherwise the modem
is stuck in a bad link state.
Tested on MC7710, T-Mobile DE, APN internet.telekom, IPv4v6 PDP type. Both
IPv4 and IPv6 connections work.

v2: Do not overwrite protocol field in rx_fixup
v3: Remove leftover struct ethhdr *eth declaration
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

sierra_net: Skip validating irrelevant fields for IDLE LSIs

When the context is deactivated, the link_type is set to 0xff, which
triggers a warning message, and results in a wrong link status, as
the LSI is ignored.

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

sierra_net: Add support for IPv6 and Dual-Stack Link Sense Indications

If a context is configured as dualstack ("IPv4v6"), the modem indicates
the context activation with a slightly different indication message.
The dual-stack indication omits the link_type (IPv4/v6) and adds
additional address fields.
IPv6 LSIs are identical to IPv4 LSIs, but have a different link type.

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

kcm: fix 0-length case for kcm_sendmsg()

Dmitry reported a kernel warning:

WARNING: CPU: 3 PID: 2936 at net/kcm/kcmsock.c:627
kcm_write_msgs+0x12e3/0x1b90 net/kcm/kcmsock.c:627
CPU: 3 PID: 2936 Comm: a.out Not tainted 4.10.0-rc6+ #209
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
  __dump_stack lib/dump_stack.c:15 [inline]
  dump_stack+0x2ee/0x3ef lib/dump_stack.c:51
  panic+0x1fb/0x412 kernel/panic.c:179
  __warn+0x1c4/0x1e0 kernel/panic.c:539
  warn_slowpath_null+0x2c/0x40 kernel/panic.c:582
  kcm_write_msgs+0x12e3/0x1b90 net/kcm/kcmsock.c:627
  kcm_sendmsg+0x163a/0x2200 net/kcm/kcmsock.c:1029
  sock_sendmsg_nosec net/socket.c:635 [inline]
  sock_sendmsg+0xca/0x110 net/socket.c:645
  sock_write_iter+0x326/0x600 net/socket.c:848
  new_sync_write fs/read_write.c:499 [inline]
  __vfs_write+0x483/0x740 fs/read_write.c:512
  vfs_write+0x187/0x530 fs/read_write.c:560
  SYSC_write fs/read_write.c:607 [inline]
  SyS_write+0xfb/0x230 fs/read_write.c:599
  entry_SYSCALL_64_fastpath+0x1f/0xc2

when calling syscall(__NR_write, sock2, 0x208aaf27ul, 0x0ul) on a KCM
seqpacket socket. It appears that kcm_sendmsg() does not handle len==0
case correctly, which causes an empty skb is allocated and queued.
Fix this by skipping the skb allocation for len==0 case.

Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xen-netfront: Rework the fix for Rx stall during OOM and network stress

The commit 90c311b0eeea ("xen-netfront: Fix Rx stall during network
stress and OOM") caused the refill timer to be triggerred almost on
all invocations of xennet_alloc_rx_buffers for certain workloads.
This reworks the fix by reverting to the old behaviour and taking into
consideration the skb allocation failure. Refill timer is now triggered
on insufficient requests or skb allocation failure.

Signed-off-by: Vineeth Remanan Pillai <vineethp@amazon.com>
Fixes: 90c311b0eeea (xen-netfront: Fix Rx stall during network stress and OOM)
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge git://git./linux/kernel/git/nab/target-pending

Pull SCSI target fixes from Nicholas Bellinger:
"This target series for v4.10 contains fixes which address a few
  long-standing bugs that DATERA's QA + automation teams have uncovered
  while putting v4.1.y target code into production usage.

  We've been running the top three in our nightly automated regression
  runs for the last two months, and the COMPARE_AND_WRITE fix Mr. Gary
  Guo has been manually verifying against a four node ESX cluster this
  past week.

  Note all of them have CC' stable tags.

  Summary:

   - Fix a bug with ESX EXTENDED_COPY + SAM_STAT_RESERVATION_CONFLICT
     status, where target_core_xcopy.c logic was incorrectly returning
     SAM_STAT_CHECK_CONDITION for all non SAM_STAT_GOOD cases (Nixon
     Vincent)

   - Fix a TMR LUN_RESET hung task bug while other in-flight TMRs are
     being aborted, before the new one had been dispatched into tmr_wq
     (Rob Millner)

   - Fix a long standing double free OOPs, where a dynamically generated
     'demo-mode' NodeACL has multiple sessions associated with it, and
     the /sys/kernel/config/target/$FABRIC/$WWN/ subsequently disables
     demo-mode, but never converts the dynamic ACL into a explicit ACL
     (Rob Millner)

   - Fix a long standing reference leak with ESX VAAI COMPARE_AND_WRITE
     when the second phase WRITE COMMIT command fails, resulting in
     CHECK_CONDITION response never being sent and se_cmd->cmd_kref
     never reaching zero (Gary Guo)

  Beyond these items on v4.1.y we've reproduced, fixed, and run through
  our regression test suite using iscsi-target exports, there are two
  additional outstanding list items:

   - Remove a >= v4.2 RCU conversion BUG_ON that would trigger when
     dynamic node NodeACLs where being converted to explicit NodeACLs.
     The patch drops the BUG_ON to follow how pre RCU conversion worked
     for this special case (Benjamin Estrabaud)

   - Add ibmvscsis target_core_fabric_ops->max_data_sg_nent assignment
     to match what IBM's Virtual SCSI hypervisor is already enforcing at
     transport layer. (Bryant Ly + Steven Royer)"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  ibmvscsis: Add SGL limit
  target: Fix COMPARE_AND_WRITE ref leak for non GOOD status
  target: Fix multi-session dynamic se_node_acl double free OOPs
  target: Fix early transport_generic_handle_tmr abort scenario
  target: Use correct SCSI status during EXTENDED_COPY exception
  target: Don't BUG_ON during NodeACL dynamic -> explicit conversion

net: phy: Fix PHY module checks and NULL deref in phy_attach_direct()

The Generic PHY drivers gets assigned after we checked that the current
PHY driver is NULL, so we need to check a few things before we can
safely dereference d->driver. This would be causing a NULL deference to
occur when a system binds to the Generic PHY driver. Update
phy_attach_direct() to do the following:

- grab the driver module reference after we have assigned the Generic
  PHY drivers accordingly, and remember we came from the generic PHY
  path

- update the error path to clean up the module reference in case the
  Generic PHY probe function fails

- split the error path involving phy_detacht() to avoid double free/put
  since phy_detach() does all the clean up

- finally, have phy_detach() drop the module reference count before we
  call device_release_driver() for the Generic PHY driver case

Fixes: cafe8df8b9bc ("net: phy: Fix lack of reference count on PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'pstore-v4.10-rc8' of git://git./linux/kernel/git/kees/linux

Pull pstore fix from Kees Cook:
"Fix pstore regression (boot Oops) when ftrace disabled, from Brian
Norris"

* tag 'pstore-v4.10-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
pstore: don't OOPS when there are no ftrace zones

Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input

Pull input fixes from Dmitry Torokhov:
"A fix for a crash in uinput, and a fix for build errors when HID-RMI
  is built-in but SERIO is a module"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: synaptics-rmi4 - select 'SERIO' when needed
  Input: uinput - fix crash when mixing old and new init style

pstore: don't OOPS when there are no ftrace zones

We'll OOPS in ramoops_get_next_prz() if the platform didn't ask for any
ftrace zones (i.e., cxt->fprzs will be NULL). Let's just skip this
entire FTRACE section if there's no 'fprzs'.

Regression seen on a coreboot/depthcharge-based Chromebook.

Fixes: 2fbea82bbb89 ("pstore: Merge per-CPU ftrace records into one")
Cc: Joel Fernandes <joelaf@google.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>

Merge tag 'vfio-v4.10-final' of git://github.com/awilliam/linux-vfio

Pull VFIO fix from Alex Williamson:
"Fix regression in attaching groups to existing container for SPAPR
IOMMU backend (Alexey Kardashevskiy)"

* tag 'vfio-v4.10-final' of git://github.com/awilliam/linux-vfio:
vfio/spapr_tce: Set window when adding additional groups to container

Merge branch 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm

Pull ARM fixes from Russell King:
"A couple more fixes for 4.10:

   - fix addressing the short regset write issue (Dave Martin)

   - fix for LPAE systems which leave a pending imprecise data abort
     before entering the kernel (Alexander Sverdlin)"

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 8643/3: arm/ptrace: Preserve previous registers for short regset write
  ARM: 8642/1: LPAE: catch pending imprecise abort on unmask

i2c: piix4: Request the SMBUS semaphore inside the mutex

SMBSLVCNT must be protected with the piix4_mutex_sb800 in order to avoid
multiple buses accessing to the semaphore at the same time.

Fixes: 701dc207bf55 ("i2c: piix4: Avoid race conditions with IMC")
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

i2c: piix4: Fix request_region size

Since '701dc207bf55 ("i2c: piix4: Avoid race conditions with IMC")' we
are using the SMBSLVCNT register at offset 0x8. We need to request it.

Fixes: 701dc207bf55 ("i2c: piix4: Avoid race conditions with IMC")
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

ALSA: hda - adding a new NV HDMI/DP codec ID in the driver

Without this change, the HDMI/DP codec will be recognised as a
generic codec, and there is no sound when playing through this codec.

As suggested by NVidia side, after adding the new ID in the driver,
the sound playing works well.

Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

powerpc/powernv: Properly set "host-ipi" on IPIs

Otherwise KVM will fail to pass them through to the host

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/powernv: Fix CPU hotplug to handle waking on HVI

The IPIs come in as HVI not EE, so we need to test the appropriate
SRR1 bits. The encoding is such that it won't have false positives
on P7 and P8 so we can just test it like that. We also need to handle
the icp-opal variant of the flush.

Fixes: d74361881f0d ("powerpc/xics: Add ICP OPAL backend")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/mm/radix: Update ERAT flushes when invalidating TLB

Three tiny changes to the ERAT flushing logic: First don't make
it depend on DD1. It hasn't been decided yet but we might run
DD2 in a mode that also requires explicit flushes for performance
reasons so make it unconditional. We also add a missing isync, and
finally remove the flush from _tlbiel_va as it is only necessary
for congruence-class invalidations (PID, LPID and full TLB), not
targetted invalidations.

Fixes: 96ed1fe511a8 ("powerpc/mm/radix: Invalidate ERAT on tlbiel for POWER9 DD1")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Revert "x86/ioapic: Restore IO-APIC irq_chip retrigger callback"

This reverts commit 020eb3daaba2857b32c4cf4c82f503d6a00a67de.

Gabriel C reports that it causes his machine to not boot, and we haven't
tracked down the reason for it yet.  Since the bug it fixes has been
around for a longish time, we're better off reverting the fix for now.

Gabriel says:
"It hangs early and freezes with a lot RCU warnings.

  I bisected it down to :

  > Ruslan Ruslichenko (1):
  >       x86/ioapic: Restore IO-APIC irq_chip retrigger callback

  Reverting this one fixes the problem for me..

  The box is a PRIMERGY TX200 S5 , 2 socket , 2 x E5520 CPU(s) installed"

and Ruslan and Thomas are currently stumped.

Reported-and-bisected-by: Gabriel C <nix.or.die@gmail.com>
Cc: Ruslan Ruslichenko <rruslich@cisco.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org # for the backport of the original commit
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Revert "hwrng: core - zeroize buffers with random data"

This reverts commit 2cc751545854d7bd7eedf4d7e377bb52e176cd07.

With this commit in place I get on a Cavium ThunderX (arm64) system:

$ if=/dev/hwrng bs=256 count=1 | od -t x1 -A x -v > rng-bad.txt
1+0 records in
1+0 records out
256 bytes (256 B) copied, 9.1171e-05 s, 2.8 MB/s
$ dd if=/dev/hwrng bs=256 count=1 | od -t x1 -A x -v >> rng-bad.txt
1+0 records in
1+0 records out
256 bytes (256 B) copied, 9.6141e-05 s, 2.7 MB/s
$ cat rng-bad.txt
000000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
000020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
000030 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
000040 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
000050 00 00 00 00 37 20 46 ae d0 fc 1c 55 25 6e b0 b8
000060 7c 7e d7 d4 00 0f 6f b2 91 1e 30 a8 fa 3e 52 0e
000070 06 2d 53 30 be a1 20 0f aa 56 6e 0e 44 6e f4 35
000080 b7 6a fe d2 52 70 7e 58 56 02 41 ea d1 9c 6a 6a
000090 d1 bd d8 4c da 35 45 ef 89 55 fc 59 d5 cd 57 ba
0000a0 4e 3e 02 1c 12 76 43 37 23 e1 9f 7a 9f 9e 99 24
0000b0 47 b2 de e3 79 85 f6 55 7e ad 76 13 4f a0 b5 41
0000c0 c6 92 42 01 d9 12 de 8f b4 7b 6e ae d7 24 fc 65
0000d0 4d af 0a aa 36 d9 17 8d 0e 8b 7a 3b b6 5f 96 47
0000e0 46 f7 d8 ce 0b e8 3e c6 13 a6 2c b6 d6 cc 17 26
0000f0 e3 c3 17 8e 9e 45 56 1e 41 ef 29 1a a8 65 c8 3a
000100
000000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
000020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
000030 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
000040 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
000050 00 00 00 00 f4 90 65 aa 8b f2 5e 31 01 53 b4 d4
000060 06 c0 23 a2 99 3d 01 e4 b0 c1 b1 55 0f 80 63 cf
000070 33 24 d8 3a 1d 5e cd 2c ba c0 d0 18 6f bc 97 46
000080 1e 19 51 b1 90 15 af 80 5e d1 08 0d eb b0 6c ab
000090 6a b4 fe 62 37 c5 e1 ee 93 c3 58 78 91 2a d5 23
0000a0 63 50 eb 1f 3b 84 35 18 cf b2 a4 b8 46 69 9e cf
0000b0 0c 95 af 03 51 45 a8 42 f1 64 c9 55 fc 69 76 63
0000c0 98 9d 82 fa 76 85 24 da 80 07 29 fe 4e 76 0c 61
0000d0 ff 23 94 4f c8 5c ce 0b 50 e8 31 bc 9d ce f4 ca
0000e0 be ca 28 da e6 fa cc 64 1c ec a8 41 db fe 42 bd
0000f0 a0 e2 4b 32 b4 52 ba 03 70 8e c1 8e d0 50 3a c6
000100

To my untrained mental entropy detector, the first several bytes of
each read from /dev/hwrng seem to not be very random (i.e. all zero).

When I revert the patch (apply this patch), I get back to what we have
in v4.9, which looks like (much more random appearing):

$ dd if=/dev/hwrng bs=256 count=1 | od -t x1 -A x -v > rng-good.txt
1+0 records in
1+0 records out
256 bytes (256 B) copied, 0.000252233 s, 1.0 MB/s
$ dd if=/dev/hwrng bs=256 count=1 | od -t x1 -A x -v >> rng-good.txt
1+0 records in
1+0 records out
256 bytes (256 B) copied, 0.000113571 s, 2.3 MB/s
$ cat rng-good.txt
000000 75 d1 2d 19 68 1f d2 26 a1 49 22 61 66 e8 09 e5
000010 e0 4e 10 d0 1a 2c 45 5d 59 04 79 8e e2 b7 2c 2e
000020 e8 ad da 34 d5 56 51 3d 58 29 c7 7a 8e ed 22 67
000030 f9 25 b9 fb c6 b7 9c 35 1f 84 21 35 c1 1d 48 34
000040 45 7c f6 f1 57 63 1a 88 38 e8 81 f0 a9 63 ad 0e
000050 be 5d 3e 74 2e 4e cb 36 c2 01 a8 14 e1 38 e1 bb
000060 23 79 09 56 77 19 ff 98 e8 44 f3 27 eb 6e 0a cb
000070 c9 36 e3 2a 96 13 07 a0 90 3f 3b bd 1d 04 1d 67
000080 be 33 14 f8 02 c2 a4 02 ab 8b 5b 74 86 17 f0 5e
000090 a1 d7 aa ef a6 21 7b 93 d1 85 86 eb 4e 8c d0 4c
0000a0 56 ac e4 45 27 44 84 9f 71 db 36 b9 f7 47 d7 b3
0000b0 f2 9c 62 41 a3 46 2b 5b e3 80 63 a4 35 b5 3c f4
0000c0 bc 1e 3a ad e4 59 4a 98 6c e8 8d ff 1b 16 f8 52
0000d0 05 5c 2f 52 2a 0f 45 5b 51 fb 93 97 a4 49 4f 06
0000e0 f3 a0 d1 1e ba 3d ed a7 60 8f bb 84 2c 21 94 2d
0000f0 b3 66 a6 61 1e 58 30 24 85 f8 c8 18 c3 77 00 22
000100
000000 73 ca cc a1 d9 bb 21 8d c3 5c f3 ab 43 6d a7 a4
000010 4a fd c5 f4 9c ba 4a 0f b1 2e 19 15 4e 84 26 e0
000020 67 c9 f2 52 4d 65 1f 81 b7 8b 6d 2b 56 7b 99 75
000030 2e cd d0 db 08 0c 4b df f3 83 c6 83 00 2e 2b b8
000040 0f af 61 1d f2 02 35 74 b5 a4 6f 28 f3 a1 09 12
000050 f2 53 b5 d2 da 45 01 e5 12 d6 46 f8 0b db ed 51
000060 7b f4 0d 54 e0 63 ea 22 e2 1d d0 d6 d0 e7 7e e0
000070 93 91 fb 87 95 43 41 28 de 3d 8b a3 a8 8f c4 9e
000080 30 95 12 7a b2 27 28 ff 37 04 2e 09 7c dd 7c 12
000090 e1 50 60 fb 6d 5f a8 65 14 40 89 e3 4c d2 87 8f
0000a0 34 76 7e 66 7a 8e 6b a3 fc cf 38 52 2e f9 26 f0
0000b0 98 63 15 06 34 99 b2 88 4f aa d8 14 88 71 f1 81
0000c0 be 51 11 2b f4 7e a0 1e 12 b2 44 2e f6 8d 84 ea
0000d0 63 82 2b 66 b3 9a fd 08 73 5a c2 cc ab 5a af b1
0000e0 88 e3 a6 80 4b fc db ed 71 e0 ae c0 0a a4 8c 35
0000f0 eb 89 f9 8a 4b 52 59 6f 09 7c 01 3f 56 e7 c7 bf
000100

Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'akpm' (patches from Andrew)

Merge fixes from Andrew Morton:
"4 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm/slub.c: fix random_seq offset destruction
  cpumask: use nr_cpumask_bits for parsing functions
  mm: avoid returning VM_FAULT_RETRY from ->page_mkwrite handlers
  kernel/ucount.c: mark user_header with kmemleak_ignore()

mm/slub.c: fix random_seq offset destruction

Commit 210e7a43fa90 ("mm: SLUB freelist randomization") broke USB hub
initialisation as described in

https://bugzilla.kernel.org/show_bug.cgi?id=177551.

Bail out early from init_cache_random_seq if s->random_seq is already
initialised. This prevents destroying the previously computed
random_seq offsets later in the function.

If the offsets are destroyed, then shuffle_freelist will truncate
page->freelist to just the first object (orphaning the rest).

Fixes: 210e7a43fa90 ("mm: SLUB freelist randomization")
Link: http://lkml.kernel.org/r/20170207140707.20824-1-sean@erifax.org
Signed-off-by: Sean Rees <sean@erifax.org>
Reported-by: <userwithuid@gmail.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Thomas Garnier <thgarnie@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

cpumask: use nr_cpumask_bits for parsing functions

Commit 513e3d2d11c9 ("cpumask: always use nr_cpu_ids in formatting and
parsing functions") converted both cpumask printing and parsing
functions to use nr_cpu_ids instead of nr_cpumask_bits.  While this was
okay for the printing functions as it just picked one of the two output
formats that we were alternating between depending on a kernel config,
doing the same for parsing wasn't okay.

nr_cpumask_bits can be either nr_cpu_ids or NR_CPUS.  We can always use
nr_cpu_ids but that is a variable while NR_CPUS is a constant, so it can
be more efficient to use NR_CPUS when we can get away with it.
Converting the printing functions to nr_cpu_ids makes sense because it
affects how the masks get presented to userspace and doesn't break
anything; however, using nr_cpu_ids for parsing functions can
incorrectly leave the higher bits uninitialized while reading in these
masks from userland.  As all testing and comparison functions use
nr_cpumask_bits which can be larger than nr_cpu_ids, the parsed cpumasks
can erroneously yield false negative results.

This made the taskstats interface incorrectly return -EINVAL even when
the inputs were correct.

Fix it by restoring the parse functions to use nr_cpumask_bits instead
of nr_cpu_ids.

Link: http://lkml.kernel.org/r/20170206182442.GB31078@htj.duckdns.org
Fixes: 513e3d2d11c9 ("cpumask: always use nr_cpu_ids in formatting and parsing functions")
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Martin Steigerwald <martin.steigerwald@teamix.de>
Debugged-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: <stable@vger.kernel.org> [4.0+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: avoid returning VM_FAULT_RETRY from ->page_mkwrite handlers

Some ->page_mkwrite handlers may return VM_FAULT_RETRY as its return
code (GFS2 or Lustre can definitely do this). However VM_FAULT_RETRY
from ->page_mkwrite is completely unhandled by the mm code and results
in locking and writeably mapping the page which definitely is not what
the caller wanted.

Fix Lustre and block_page_mkwrite_ret() used by other filesystems
(notably GFS2) to return VM_FAULT_NOPAGE instead which results in
bailing out from the fault code, the CPU then retries the access, and we
fault again effectively doing what the handler wanted.

Link: http://lkml.kernel.org/r/20170203150729.15863-1-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/ucount.c: mark user_header with kmemleak_ignore()

The user_header gets caught by kmemleak with the following splat as
missing a free:

  unreferenced object 0xffff99667a733d80 (size 96):
  comm "swapper/0", pid 1, jiffies 4294892317 (age 62191.468s)
  hex dump (first 32 bytes):
    a0 b6 92 b4 ff ff ff ff 00 00 00 00 01 00 00 00  ................
    01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
     kmemleak_alloc+0x4a/0xa0
     __kmalloc+0x144/0x260
     __register_sysctl_table+0x54/0x5e0
     register_sysctl+0x1b/0x20
     user_namespace_sysctl_init+0x17/0x34
     do_one_initcall+0x52/0x1a0
     kernel_init_freeable+0x173/0x200
     kernel_init+0xe/0x100
     ret_from_fork+0x2c/0x40

The BUG_ON()s are intended to crash so no need to clean up after
ourselves on error there.  This is also a kernel/ subsys_init() we don't
need a respective exit call here as this is never modular, so just white
list it.

Link: http://lkml.kernel.org/r/20170203211404.31458-1-mcgrof@kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Nikolay Borisov <n.borisov.lkml@gmail.com>
Cc: Serge Hallyn <serge@hallyn.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drm: vc4: adapt to new behaviour of drm_crtc.c

When drm_crtc_init_with_planes() was orignally added
(in drm_crtc.c, e13161af80c185ecd8dc4641d0f5df58f9e3e0af
drm: Add drm_crtc_init_with_planes() (v2)), it only checked for "primary"
being non-null. If that was the case, it modified primary->possible_crtcs.

Then, when support for cursor planes was added
(fc1d3e44ef7c1db93384150fdbf8948dcf949f15 drm: Allow drivers to register
cursor planes with crtc), the same behaviour was implemented for cursor
planes.

vc4_plane_init() since its inception has passed 0xff as "possible_crtcs"
parameter to drm_universal_plane_init(). With a change in drm_crtc.c
(7abc7d47510c75dd984380ebf819616e574c9604 drm: don't override
possible_crtcs for primary/cursor planes) passing 0xff results in primary's
possible_crtcs set to 0xff (cursor was updated manually by vc4_crtc.c).
Consequently, it would be allowed to use the primary plane from CRTC 1 (for
example) on CRTC 0, which would result in the overlay and cursors being
buried.

Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/1485941708-27892-1-git-send-email-andrzej.p@samsung.com
Fixes: 7abc7d47510c ("drm: don't override possible_crtcs for primary/cursor planes")

net: thunderx: Fix PHY autoneg for SGMII QLM mode

This patch fixes the case where there is no phydev attached
to a LMAC in DT due to non-existance of a PHY driver or due
to usage of non-stanadard PHY which doesn't support autoneg.
Changes dependeds on firmware to send correct info w.r.t
PHY and autoneg capability.

This patch also covers a case where a 10G/40G interface is used
as a 1G with convertors with Cortina PHY in between.

Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'pci-v4.10-fixes-3' of git://git./linux/kernel/git/helgaas/pci

Pull PCI fixes from Bjorn Helgaas:

- check MSI affinity vs. number of vectors to avoid memory corruption

- drop runtime power management for PCIe hotplug ports for now to avoid
   regressing hotplug via sysfs

* tag 'pci-v4.10-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  Revert "PCI: pciehp: Add runtime PM support for PCIe hotplug ports"
  PCI/MSI: Don't apply affinity if there aren't enough vectors left

net: dsa: Do not destroy invalid network devices

dsa_slave_create() can fail, and dsa_user_port_unapply() will properly check
for the network device not being NULL before attempting to destroy it. We were
not setting the slave network device as NULL if dsa_slave_create() failed, so
we would later on be calling dsa_slave_destroy() on a now free'd and
unitialized network device, causing crashes in dsa_slave_destroy().

Fixes: 83c0afaec7b7 ("net: dsa: Add new binding implementation")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ping: fix a null pointer dereference

Andrey reported a kernel crash:

  general protection fault: 0000 [#1] SMP KASAN
  Dumping ftrace buffer:
     (ftrace buffer empty)
  Modules linked in:
  CPU: 2 PID: 3880 Comm: syz-executor1 Not tainted 4.10.0-rc6+ #124
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
  task: ffff880060048040 task.stack: ffff880069be8000
  RIP: 0010:ping_v4_push_pending_frames net/ipv4/ping.c:647 [inline]
  RIP: 0010:ping_v4_sendmsg+0x1acd/0x23f0 net/ipv4/ping.c:837
  RSP: 0018:ffff880069bef8b8 EFLAGS: 00010206
  RAX: dffffc0000000000 RBX: ffff880069befb90 RCX: 0000000000000000
  RDX: 0000000000000018 RSI: ffff880069befa30 RDI: 00000000000000c2
  RBP: ffff880069befbb8 R08: 0000000000000008 R09: 0000000000000000
  R10: 0000000000000002 R11: 0000000000000000 R12: ffff880069befab0
  R13: ffff88006c624a80 R14: ffff880069befa70 R15: 0000000000000000
  FS:  00007f6f7c716700(0000) GS:ffff88006de00000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00000000004a6f28 CR3: 000000003a134000 CR4: 00000000000006e0
  Call Trace:
   inet_sendmsg+0x164/0x5b0 net/ipv4/af_inet.c:744
   sock_sendmsg_nosec net/socket.c:635 [inline]
   sock_sendmsg+0xca/0x110 net/socket.c:645
   SYSC_sendto+0x660/0x810 net/socket.c:1687
   SyS_sendto+0x40/0x50 net/socket.c:1655
   entry_SYSCALL_64_fastpath+0x1f/0xc2

This is because we miss a check for NULL pointer for skb_peek() when
the queue is empty. Other places already have the same check.

Fixes: c319b4d76b9e ("net: ipv4: add IPPROTO_ICMP socket kind")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-header-length-truncation'

Willem de Bruijn says:

====================
net: Fixes for header length truncation

Packets should not enter the stack with truncated link layer headers
and link layer headers should always be stored in the skb linear
segment.

Patch 1 ensures the first for PF_PACKET sockets
Patch 2 ensures the second for PF_PACKET GSO sockets without tx_ring
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

packet: round up linear to header len

Link layer protocols may unconditionally pull headers, as Ethernet
does in eth_type_trans. Ensure that the entire link layer header
always lies in the skb linear segment. tpacket_snd has such a check.
Extend this to packet_snd.

Variable length link layer headers complicate the computation
somewhat. Here skb->len may be smaller than dev->hard_header_len.

Round up the linear length to be at least as long as the smallest of
the two.

Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: introduce device min_header_len

The stack must not pass packets to device drivers that are shorter
than the minimum link layer header length.

Previously, packet sockets would drop packets smaller than or equal
to dev->hard_header_len, but this has false positives. Zero length
payload is used over Ethernet. Other link layer protocols support
variable length headers. Support for validation of these protocols
removed the min length check for all protocols.

Introduce an explicit dev->min_header_len parameter and drop all
packets below this value. Initially, set it to non-zero only for
Ethernet and loopback. Other protocols can follow in a patch to
net-next.

Fixes: 9ed988cd5915 ("packet: validate variable length ll headers")
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ibmvscsis: Add SGL limit

This patch adds internal LIO sgl limit since the driver already
sets a max transfer limit on transport layer of 1MB to the client.

Cc: stable@vger.kernel.org
Tested-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

sit: fix a double free on error path

Dmitry reported a double free in sit_init_net():

  kernel BUG at mm/percpu.c:689!
  invalid opcode: 0000 [#1] SMP KASAN
  Dumping ftrace buffer:
     (ftrace buffer empty)
  Modules linked in:
  CPU: 0 PID: 15692 Comm: syz-executor1 Not tainted 4.10.0-rc6-next-20170206 #1
  Hardware name: Google Google Compute Engine/Google Compute Engine,
  BIOS Google 01/01/2011
  task: ffff8801c9cc27c0 task.stack: ffff88017d1d8000
  RIP: 0010:pcpu_free_area+0x68b/0x810 mm/percpu.c:689
  RSP: 0018:ffff88017d1df488 EFLAGS: 00010046
  RAX: 0000000000010000 RBX: 00000000000007c0 RCX: ffffc90002829000
  RDX: 0000000000010000 RSI: ffffffff81940efb RDI: ffff8801db841d94
  RBP: ffff88017d1df590 R08: dffffc0000000000 R09: 1ffffffff0bb3bdd
  R10: dffffc0000000000 R11: 00000000000135dd R12: ffff8801db841d80
  R13: 0000000000038e40 R14: 00000000000007c0 R15: 00000000000007c0
  FS:  00007f6ea608f700(0000) GS:ffff8801dbe00000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 000000002000aff8 CR3: 00000001c8d44000 CR4: 00000000001426f0
  DR0: 0000000020000000 DR1: 0000000020000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000600
  Call Trace:
   free_percpu+0x212/0x520 mm/percpu.c:1264
   ipip6_dev_free+0x43/0x60 net/ipv6/sit.c:1335
   sit_init_net+0x3cb/0xa10 net/ipv6/sit.c:1831
   ops_init+0x10a/0x530 net/core/net_namespace.c:115
   setup_net+0x2ed/0x690 net/core/net_namespace.c:291
   copy_net_ns+0x26c/0x530 net/core/net_namespace.c:396
   create_new_namespaces+0x409/0x860 kernel/nsproxy.c:106
   unshare_nsproxy_namespaces+0xae/0x1e0 kernel/nsproxy.c:205
   SYSC_unshare kernel/fork.c:2281 [inline]
   SyS_unshare+0x64e/0xfc0 kernel/fork.c:2231
   entry_SYSCALL_64_fastpath+0x1f/0xc2

This is because when tunnel->dst_cache init fails, we free dev->tstats
once in ipip6_tunnel_init() and twice in sit_init_net(). This looks
redundant but its ndo_uinit() does not seem enough to clean up everything
here. So avoid this by setting dev->tstats to NULL after the first free,
at least for -net.

Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Arnd Bergmann:

- A relatively large patch restores booting on i.MX platforms that
   failed to boot after a cleanup was merged for v4.10.

- A quirk for USB needs to be enabled on the STi platform

- On the Meson platform, we saw memory corruption with part of the
   memory used by the secure monitor, so we have to stay out of that
   area.

- The same platform also has a problem with ethernet under load, which
   is fixed by disabling EEE negotiation.

- imx6dl has an incorrect pin configuration, which prevents SPI from
   working.

- Two maintainers have lost their access to their email addresses, so
   we should update the MAINTAINERS file before the release

- Renaming one of the orion5x linkstation models to help simplify the
   debian install.

- A couple of fixes for build warnings that were introduced during
   v4.10-rc.

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: defconfigs: make NF_CT_PROTO_SCTP and NF_CT_PROTO_UDPLITE built-in
  MAINTAINERS: socfpga: update email for Dinh Nguyen
  ARM: orion5x: fix Makefile for linkstation-lschl.dtb
  ARM: dts: orion5x-lschl: More consistent naming on linkstation series
  ARM: dts: orion5x-lschl: Fix model name
  MAINTAINERS: change email address from atmel to microchip
  MAINTAINERS: at91: change email address
  ARM64: dts: meson-gx: Add firmware reserved memory zones
  ARM64: dts: meson-gxbb-odroidc2: fix GbE tx link breakage
  ARM: dts: STiH407-family: set snps,dis_u3_susphy_quirk
  ARM: dts: imx: Pass 'chosen' and 'memory' nodes
  ARM: dts: imx6dl: fix GPIO4 range
  ARM: imx: hide unused variable in #ifdef

Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/linux-security

Pull selinux fix from James Morris:
"Fix off-by-one in setprocattr"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selinux: fix off-by-one in setprocattr

Merge branch 'for-linus' of git://git.kernel.dk/linux-block

Pull block fix from Jens Axboe:
"A single fix that should go into 4.10, fixing a regression on some
devices with the WRITE_SAME command"

* 'for-linus' of git://git.kernel.dk/linux-block:
block: don't try Write Same from __blkdev_issue_zeroout

lwtunnel: valid encap attr check should return 0 when lwtunnel is disabled

An error was reported upgrading to 4.9.8:
    root@Typhoon:~# ip route add default table 210 nexthop dev eth0 via 10.68.64.1
    weight 1 nexthop dev eth0 via 10.68.64.2 weight 1
    RTNETLINK answers: Operation not supported

The problem occurs when CONFIG_LWTUNNEL is not enabled and a multipath
route is submitted.

The point of lwtunnel_valid_encap_type_attr is catch modules that
need to be loaded before any references are taken with rntl held. With
CONFIG_LWTUNNEL disabled, there will be no modules to load so the
lwtunnel_valid_encap_type_attr stub should just return 0.

Fixes: 9ed59592e3e3 ("lwtunnel: fix autoload of lwt modules")
Reported-by: pupilla@libero.it
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RDMA: Don't reference kernel private header from UAPI header

Remove references to private kernel header and defines from exported
ib_user_verb.h file.

The code snippet below is used to reproduce the issue:

#include <stdio.h>
#include <rdma/ib_user_verb.h>

int main(void)
{
printf("IB_USER_VERBS_ABI_VERSION = %d\n", IB_USER_VERBS_ABI_VERSION);
return 0;
}

It fails during compilation phase with an error:
➜ /tmp gcc main.c
main.c:2:31: fatal error: rdma/ib_user_verb.h: No such file or directory
#include <rdma/ib_user_verb.h>
^
compilation terminated.

Fixes: 189aba99e700 ("IB/uverbs: Extend modify_qp and support packet pacing")
CC: Bodong Wang <bodong@mellanox.com>
CC: Matan Barak <matanb@mellanox.com>
CC: Christoph Hellwig <hch@infradead.org>
Tested-by: Slava Shwartsman <slavash@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/rxe: Fix mem_check_range integer overflow

Update the range check to avoid integer-overflow in edge case.
Resolves CVE 2016-8636.

Signed-off-by: Eyal Itkin <eyal.itkin@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/rxe: Fix resid update

Update the response's resid field when larger than MTU, instead of only
updating the local resid variable.

Fixes: 8700e3e7c485 ("Soft RoCE driver")
Signed-off-by: Eyal Itkin <eyal.itkin@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

ipv6: addrconf: fix generation of new temporary addresses

Under some circumstances it is possible that no new temporary addresses
will be generated.

For instance, addrconf_prefix_rcv_add_addr() indirectly calls
ipv6_create_tempaddr(), which creates a tentative temporary address and
starts dad. Next, addrconf_prefix_rcv_add_addr() indirectly calls
addrconf_verify_rtnl(). Now, assume that the previously created temporary
address has the least preferred lifetime among all existing addresses and
is still tentative (that is, dad is still running). Hence, the next run of
addrconf_verify_rtnl() is performed when the preferred lifetime of the
temporary address ends. If dad succeeds before the next run, the temporary
address becomes deprecated during the next run, but no new temporary
address is generated.

In order to fix this, schedule the next addrconf_verify_rtnl() run slightly
before the temporary address becomes deprecated, if dad succeeded.

Signed-off-by: Marcus Huewe <suse-tux@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

btrfs: fix btrfs_compat_ioctl failures on non-compat ioctls

Commit 4c63c2454ef incorrectly assumed that returning -ENOIOCTLCMD would
cause the native ioctl to be called. The ->compat_ioctl callback is
expected to handle all ioctls, not just compat variants. As a result,
when using 32-bit userspace on 64-bit kernels, everything except those
three ioctls would return -ENOTTY.

Fixes: 4c63c2454ef ("btrfs: bugfix: handle FS_IOC32_{GETFLAGS,SETFLAGS,GETVERSION} in btrfs_ioctl")
Cc: stable@vger.kernel.org
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>

target: Fix COMPARE_AND_WRITE ref leak for non GOOD status

This patch addresses a long standing bug where the commit phase
of COMPARE_AND_WRITE would result in a se_cmd->cmd_kref reference
leak if se_cmd->scsi_status returned non SAM_STAT_GOOD.

This would manifest first as a lost SCSI response, and eventual
hung task during fabric driver logout or re-login, as existing
shutdown logic waited for the COMPARE_AND_WRITE se_cmd->cmd_kref
to reach zero.

To address this bug, compare_and_write_post() has been changed
to drop the incorrect !cmd->scsi_status conditional that was
preventing *post_ret = 1 for being set during non SAM_STAT_GOOD
status.

This patch has been tested with SAM_STAT_CHECK_CONDITION status
from normal target_complete_cmd() callback path, as well as the
incoming __target_execute_cmd() submission failure path when
se_cmd->execute_cmd() returns non zero status.

Reported-by: Donald White <dew@datera.io>
Cc: Donald White <dew@datera.io>
Tested-by: Gary Guo <ghg@datera.io>
Cc: Gary Guo <ghg@datera.io>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

target: Fix multi-session dynamic se_node_acl double free OOPs

This patch addresses a long-standing bug with multi-session
(eg: iscsi-target + iser-target) se_node_acl dynamic free
withini transport_deregister_session().

This bug is caused when a storage endpoint is configured with
demo-mode (generate_node_acls = 1 + cache_dynamic_acls = 1)
initiators, and initiator login creates a new dynamic node acl
and attaches two sessions to it.

After that, demo-mode for the storage instance is disabled via
configfs (generate_node_acls = 0 + cache_dynamic_acls = 0) and
the existing dynamic acl is never converted to an explicit ACL.

The end result is dynamic acl resources are released twice when
the sessions are shutdown in transport_deregister_session().

If the storage instance is not changed to disable demo-mode,
or the dynamic acl is converted to an explict ACL, or there
is only a single session associated with the dynamic ACL,
the bug is not triggered.

To address this big, move the release of dynamic se_node_acl
memory into target_complete_nacl() so it's only freed once
when se_node_acl->acl_kref reaches zero.

(Drop unnecessary list_del_init usage - HCH)

Reported-by: Rob Millner <rlm@daterainc.com>
Tested-by: Rob Millner <rlm@daterainc.com>
Cc: Rob Millner <rlm@daterainc.com>
Cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

target: Fix early transport_generic_handle_tmr abort scenario

This patch fixes a bug where incoming task management requests
can be explicitly aborted during an active LUN_RESET, but who's
struct work_struct are canceled in-flight before execution.

This occurs when core_tmr_drain_tmr_list() invokes cancel_work_sync()
for the incoming se_tmr_req->task_cmd->work, resulting in cmd->work
for target_tmr_work() never getting invoked and the aborted TMR
waiting indefinately within transport_wait_for_tasks().

To address this case, perform a CMD_T_ABORTED check early in
transport_generic_handle_tmr(), and invoke the normal path via
transport_cmd_check_stop_to_fabric() to complete any TMR kthreads
blocked waiting for CMD_T_STOP in transport_wait_for_tasks().

Also, move the TRANSPORT_ISTATE_PROCESSING assignment earlier
into transport_generic_handle_tmr() so the existing check in
core_tmr_drain_tmr_list() avoids attempting abort the incoming
se_tmr_req->task_cmd->work if it has already been queued into
se_device->tmr_wq.

Reported-by: Rob Millner <rlm@daterainc.com>
Tested-by: Rob Millner <rlm@daterainc.com>
Cc: Rob Millner <rlm@daterainc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

target: Use correct SCSI status during EXTENDED_COPY exception

This patch adds the missing target_complete_cmd() SCSI status
parameter change in target_xcopy_do_work(), that was originally
missing in commit 926317de33.

It correctly propigates up the correct SCSI status during
EXTENDED_COPY exception cases, instead of always using the
hardcoded SAM_STAT_CHECK_CONDITION from original code.

This is required for ESX host environments that expect to
hit SAM_STAT_RESERVATION_CONFLICT for certain scenarios,
and SAM_STAT_CHECK_CONDITION results in non-retriable
status for these cases.

Reported-by: Nixon Vincent <nixon.vincent@calsoftinc.com>
Tested-by: Nixon Vincent <nixon.vincent@calsoftinc.com>
Cc: Nixon Vincent <nixon.vincent@calsoftinc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

target: Don't BUG_ON during NodeACL dynamic -> explicit conversion

After the v4.2+ RCU conversion to se_node_acl->lun_entry_hlist,
a BUG_ON() was added in core_enable_device_list_for_node() to
detect when the located orig->se_lun_acl contains an existing
se_lun_acl pointer reference.

However, this scenario can happen when a dynamically generated
NodeACL is being converted to an explicit NodeACL, when the
explicit NodeACL contains a different LUN mapping than the
default provided by the WWN endpoint.

So instead of triggering BUG_ON(), go ahead and fail instead
following the original pre RCU conversion logic.

Reported-by: Benjamin ESTRABAUD <ben.estrabaud@mpstor.com>
Cc: Benjamin ESTRABAUD <ben.estrabaud@mpstor.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

powerpc/mm: Fix spurrious segfaults on radix with autonuma

When autonuma (Automatic NUMA balancing) marks a PTE inaccessible it
clears all the protection bits but leave the PTE valid.

With the Radix MMU, an attempt at executing from such a PTE will
take a fault with bit 35 of SRR1 set "SRR1_ISI_N_OR_G".

It is thus incorrect to treat all such faults as errors. We should
pass them to handle_mm_fault() for autonuma to deal with. The case
of pages that are really not executable is handled by the existing
test for VM_EXEC further down.

That leaves us with catching the kernel attempts at executing user
pages. We can catch that earlier, even before we do find_vma.

It is never valid on powerpc for the kernel to take an exec fault
to begin with. So fold that test with the existing test for the
kernel faulting on kernel addresses to bail out early.

Fixes: 1d18ad026844 ("powerpc/mm: Detect instruction fetch denied and report")
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

ALSA: seq: Fix race at creating a queue

When a sequencer queue is created in snd_seq_queue_alloc(),it adds the
new queue element to the public list before referencing it. Thus the
queue might be deleted before the call of snd_seq_queue_use(), and it
results in the use-after-free error, as spotted by syzkaller.

The fix is to reference the queue object at the right time.

Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

drm/i915: Always convert incoming exec offsets to non-canonical

We're using non-canonical addresses in drm_mm, and we're making sure that
userspace is using canonical addressing - both in case of softpin
(verifying incoming offset) and when relocating (converting to canonical
when updating offset returned to userspace).
Unfortunately when considering the need for relocations, we're comparing
offset from userspace (in canonical form) with drm_mm node (in
non-canonical form), and as a result, we end up always relocating if our
offsets are in the "problematic" range.
Let's always convert the offsets to avoid the performance impact of
relocations.

Fixes: a5f0edf63bdf ("drm/i915: Avoid writing relocs with addresses in non-canonical form")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Reported-by: Michał Pyrzowski <michal.pyrzowski@intel.com>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207195559.18798-1-michal.winiarski@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 038c95a313e4ca954ee5ab8a0c7559a646b0f462)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Remove overzealous fence warn on runtime suspend

The goal of the WARN was to catch when we are still actively using the
fence as we go into the runtime suspend. However, the reg->pin_count is
too coarse as it does not distinguish between exclusive ownership of the
fence register from activity.

I've not improved on the WARN, nor have we captured this WARN in an
exact igt, but it is showing up regularly in the wild:

[ 1915.935332] WARNING: CPU: 1 PID: 10861 at drivers/gpu/drm/i915/i915_gem.c:2022 i915_gem_runtime_suspend+0x116/0x130 [i915]
[ 1915.935383] WARN_ON(reg->pin_count)[ 1915.935399] Modules linked in:
snd_hda_intel i915 drm_kms_helper vgem netconsole scsi_transport_iscsi fuse vfat fat x86_pkg_temp_thermal coretemp intel_cstate intel_uncore snd_hda_codec_hdmi snd_hda_codec_generic snd_hda_codec snd_hwdep snd_hda_core snd_pcm snd_timer snd mei_me mei serio_raw intel_rapl_perf intel_pch_thermal soundcore wmi acpi_pad i2c_algo_bit syscopyarea sysfillrect sysimgblt fb_sys_fops drm r8169 mii video [last unloaded: drm_kms_helper]
[ 1915.935785] CPU: 1 PID: 10861 Comm: kworker/1:0 Tainted: G     U  W       4.9.0-rc5+ #170
[ 1915.935799] Hardware name: LENOVO 80MX/Lenovo E31-80, BIOS DCCN34WW(V2.03) 12/01/2015
[ 1915.935822] Workqueue: pm pm_runtime_work
[ 1915.935845]  ffffc900044fbbf0 ffffffffac3220bc ffffc900044fbc40 0000000000000000
[ 1915.935890]  ffffc900044fbc30 ffffffffac059bcb 000007e6044fbc60 ffff8801626e3198
[ 1915.935937]  ffff8801626e0000 0000000000000002 ffffffffc05e5d4e 0000000000000000
[ 1915.935985] Call Trace:
[ 1915.936013]  [<ffffffffac3220bc>] dump_stack+0x4f/0x73
[ 1915.936038]  [<ffffffffac059bcb>] __warn+0xcb/0xf0
[ 1915.936060]  [<ffffffffac059c4f>] warn_slowpath_fmt+0x5f/0x80
[ 1915.936158]  [<ffffffffc052d916>] i915_gem_runtime_suspend+0x116/0x130 [i915]
[ 1915.936251]  [<ffffffffc04f1c74>] intel_runtime_suspend+0x64/0x280 [i915]
[ 1915.936277]  [<ffffffffac0926f1>] ? dequeue_entity+0x241/0xbc0
[ 1915.936298]  [<ffffffffac36bb85>] pci_pm_runtime_suspend+0x55/0x180
[ 1915.936317]  [<ffffffffac36bb30>] ? pci_pm_runtime_resume+0xa0/0xa0
[ 1915.936339]  [<ffffffffac4514e2>] __rpm_callback+0x32/0x70
[ 1915.936356]  [<ffffffffac451544>] rpm_callback+0x24/0x80
[ 1915.936375]  [<ffffffffac36bb30>] ? pci_pm_runtime_resume+0xa0/0xa0
[ 1915.936392]  [<ffffffffac45222d>] rpm_suspend+0x12d/0x680
[ 1915.936415]  [<ffffffffac69f6d7>] ? _raw_spin_unlock_irq+0x17/0x30
[ 1915.936435]  [<ffffffffac0810b8>] ? finish_task_switch+0x88/0x220
[ 1915.936455]  [<ffffffffac4534bf>] pm_runtime_work+0x6f/0xb0
[ 1915.936477]  [<ffffffffac074353>] process_one_work+0x1f3/0x4d0
[ 1915.936501]  [<ffffffffac074678>] worker_thread+0x48/0x4e0
[ 1915.936523]  [<ffffffffac074630>] ? process_one_work+0x4d0/0x4d0
[ 1915.936542]  [<ffffffffac074630>] ? process_one_work+0x4d0/0x4d0
[ 1915.936559]  [<ffffffffac07a2c9>] kthread+0xd9/0xf0
[ 1915.936580]  [<ffffffffac07a1f0>] ? kthread_park+0x60/0x60
[ 1915.936600]  [<ffffffffac69fe62>] ret_from_fork+0x22/0x30

In the case the register is pinned, it should be present and we will
need to invalidate them to be restored upon resume as we cannot expect
the owner of the pin to call get_fence prior to use after resume.

Fixes: 7c108fd8feac ("drm/i915: Move fence cancellation to runtime suspend")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98804
Reported-by: Lionel Landwerlin <lionel.g.landwerlin@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Imre Deak <imre.deak@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.10-rc1+
Link: http://patchwork.freedesktop.org/patch/msgid/20170203125717.8431-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit e0ec3ec698851a6c97a12d696407b3ff77700c23)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/bxt: Add MST support when do DPLL calculation

Add the missing INTEL_OUTPUT_DP_MST case in bxt_get_dpll()
to correctly initialize the crtc_state and port plls when
link training a DP MST monitor on BXT/APL devices.

Fixes: a277ca7dc01d ("drm/i915: Split bxt_ddi_pll_select()")
Bugs: https://bugs.freedesktop.org/show_bug.cgi?id=99572
Reviewed-by: Cooper Chiou <cooper.chiou@intel.com>
Reviewed-by: Gary C Wang <gary.c.wang@intel.com>
Reviewed-by: Ciobanu, Nathan D <nathan.d.ciobanu@intel.com>
Reviewed-by: Herbert, Marc <marc.herbert@intel.com>
Reviewed-by: Bride, Jim <jim.bride@intel.com>
Reviewed-by: Navare, Manasi D <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Lee, Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1486096329-6255-1-git-send-email-shawn.c.lee@intel.com
(cherry picked from commit 0aab2c721d81590012a5021a516f00666646741f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

mmc: mmci: avoid clearing ST Micro busy end interrupt mistakenly

This fixes a race condition that may occur whenever ST micro busy end
interrupt is raised just after being unmasked but before leaving mmci
interrupt context.

A dead-lock has been found if connecting mmci ST Micro variant whose amba
id is 0x10480180 to some new eMMC that supports internal caches.  Whenever
mmci driver enables cache control by programming eMMC's EXT_CSD register,
block driver may request to flush the eMMC internal caches causing mmci
driver to send a MMC_SWITCH command to the card with FLUSH_CACHE operation.
And because busy end interrupt may be mistakenly cleared while not yet
processed, this mmc request may never complete.  As a result, mmcqd task
may be stuck forever.

Here is an instance caught by lockup detector which shows that mmcqd task
was hung while waiting for mmc_flush_cache command to complete:

..
[  240.251595] INFO: task mmcqd/1:52 blocked for more than 120 seconds.
[  240.257973]       Not tainted 4.1.13-00510-g9d91424 #2
[  240.263109] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  240.270955] mmcqd/1         D c047504c     0    52      2 0x00000000
[  240.277359] [<c047504c>] (__schedule) from [<c04754a0>] (schedule+0x40/0x98)
[  240.284418] [<c04754a0>] (schedule) from [<c0477d40>] (schedule_timeout+0x148/0x188)
[  240.292191] [<c0477d40>] (schedule_timeout) from [<c0476040>] (wait_for_common+0xa4/0x170)
[  240.300491] [<c0476040>] (wait_for_common) from [<c02efc1c>] (mmc_wait_for_req_done+0x4c/0x13c)
[  240.309224] [<c02efc1c>] (mmc_wait_for_req_done) from [<c02efd90>] (mmc_wait_for_cmd+0x64/0x84)
[  240.317953] [<c02efd90>] (mmc_wait_for_cmd) from [<c02f5b14>] (__mmc_switch+0xa4/0x2a8)
[  240.325964] [<c02f5b14>] (__mmc_switch) from [<c02f5d40>] (mmc_switch+0x28/0x30)
[  240.333389] [<c02f5d40>] (mmc_switch) from [<c02f0984>] (mmc_flush_cache+0x54/0x80)
[  240.341073] [<c02f0984>] (mmc_flush_cache) from [<c02ff0c4>] (mmc_blk_issue_rq+0x114/0x4e8)
[  240.349459] [<c02ff0c4>] (mmc_blk_issue_rq) from [<c03008d4>] (mmc_queue_thread+0xc0/0x180)
[  240.357844] [<c03008d4>] (mmc_queue_thread) from [<c003cf90>] (kthread+0xdc/0xf4)
[  240.365339] [<c003cf90>] (kthread) from [<c0010068>] (ret_from_fork+0x14/0x2c)
..
..
[  240.664311] INFO: task partprobe:564 blocked for more than 120 seconds.
[  240.670943]       Not tainted 4.1.13-00510-g9d91424 #2
[  240.676078] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  240.683922] partprobe       D c047504c     0   564    486 0x00000000
[  240.690318] [<c047504c>] (__schedule) from [<c04754a0>] (schedule+0x40/0x98)
[  240.697396] [<c04754a0>] (schedule) from [<c0477d40>] (schedule_timeout+0x148/0x188)
[  240.705149] [<c0477d40>] (schedule_timeout) from [<c0476040>] (wait_for_common+0xa4/0x170)
[  240.713446] [<c0476040>] (wait_for_common) from [<c01f3300>] (submit_bio_wait+0x58/0x64)
[  240.721571] [<c01f3300>] (submit_bio_wait) from [<c01fbbd8>] (blkdev_issue_flush+0x60/0x88)
[  240.729957] [<c01fbbd8>] (blkdev_issue_flush) from [<c010ff84>] (blkdev_fsync+0x34/0x44)
[  240.738083] [<c010ff84>] (blkdev_fsync) from [<c0109594>] (do_fsync+0x3c/0x64)
[  240.745319] [<c0109594>] (do_fsync) from [<c000ffc0>] (ret_fast_syscall+0x0/0x3c)
..

Here is the detailed sequence showing when this issue may happen:

1) At probe time, mmci device is initialized and card busy detection based
on DAT[0] monitoring is enabled.

2) Later during run time, since card reported to support internal caches, a
MMCI_SWITCH command is sent to eMMC device with FLUSH_CACHE operation. On
receiving this command, eMMC may enter busy state (for a relatively short
time in the case of the dead-lock).

3) Then mmci interrupt is raised and mmci_irq() is called:

MMCISTATUS register is read and is equal to 0x01000440. So the following
status bits are set:
- MCI_CMDRESPEND (= 6)
- MCI_DATABLOCKEND (= 10)
- MCI_ST_CARDBUSY (= 24)

Since MMCIMASK0 register is 0x3FF, status variable is set to 0x00000040 and
BIT MCI_CMDRESPEND is cleared by writing MMCICLEAR register.

Then mmci_cmd_irq() is called. Considering the following conditions:
- host->busy_status is 0,
- this is a "busy response",
- reading again MMCISTATUS register gives 0x1000400,
MMCIMASK0 is updated to unmask MCI_ST_BUSYEND bit.

Thus, MMCIMASK0 is set to 0x010003FF and host->busy_status is set to wait
for busy end completion.

Back again in status loop of mmci_irq(), we quickly go through
mmci_data_irq() as there are no data in that case.  And we finally go
through following test at the end of while(status) loop:

/*
* Don't poll for busy completion in irq context.
*/
if (host->variant->busy_detect && host->busy_status)
status &= ~host->variant->busy_detect_flag;

Because status variable is not yet null (is equal to 0x40), we do not leave
interrupt context yet but we loop again into while(status) loop. So we run
across following steps:

a) MMCISTATUS register is read again and this time is equal to 0x01000400.
So that following bits are set:
- MCI_DATABLOCKEND (= 10)
- MCI_ST_CARDBUSY (= 24)

Since MMCIMASK0 register is equal to 0x010003FF:

b) status variable is set to 0x01000000.
c) MCI_ST_CARDBUSY bit is cleared by writing MMCICLEAR register.

Then, mmci_cmd_irq() is called one more time. Since host->busy_status is
set and that MCI_ST_CARDBUSY is set in status variable, we just return from
this function.

Back again in mmci_irq(), status variable is set to 0 and we finally leave
the while(status) loop. As a result we leave interrupt context, waiting for
busy end interrupt event.

Now, consider that busy end completion is raised IN BETWEEN steps 3.a) and
3.c). In such a case, we may mistakenly clear busy end interrupt at step
3.c) while it has not yet been processed. This will result in mmc command
to wait forever for a busy end completion that will never happen.

To fix the problem, this patch implements the following changes:

Considering that the mmci seems to be triggering the IRQ on both edges
while monitoring DAT0 for busy completion and that same status bit is used
to monitor start and end of busy detection, special care must be taken to
make sure that both start and end interrupts are always cleared one after
the other.

1) Clearing of card busy bit is moved in mmc_cmd_irq() function where
unmasking of busy end bit is effectively handled.
2) Just before unmasking busy end event, busy start event is cleared by
writing card busy bit in MMCICLEAR register.
3) Finally, once we are no more busy with a command, busy end event is
cleared writing again card busy bit in MMCICLEAR register.

This patch has been tested with the ST Accordo5 machine, not yet supported
upstream but relies on the mmci driver.

Signed-off-by: Sarang Mairal <sarang.mairal@garmin.com>
Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

drm/i915: don't warn about Skylake CPU - KabyPoint PCH combo

Apparently there are machines out there with Skylake CPU and KabyPoint
PCH. Judging from our driver code, there doesn't seem to be any code
paths that would do anything different between SunrisePoint and
KabyPoint PCHs, so it would seem okay to accept the combo without
warnings.

Fixes: 22dea0be50b2 ("drm/i915: Introduce Kabypoint PCH for Kabylake H/DT.")
References: https://lists.freedesktop.org/archives/intel-gfx/2017-February/118611.html
Reported-by: Rainer Koenig <Rainer.Koenig@ts.fujitsu.com>
Cc: Rainer Koenig <Rainer.Koenig@ts.fujitsu.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: <stable@vger.kernel.org> # v4.8+
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485956769-26015-1-git-send-email-jani.nikula@intel.com
(cherry picked from commit 3aac4acb89710fe782c9e78e7b1febf76e112c6c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: fix i915 running as dom0 under Xen

Commit 920cf4194954ec ("drm/i915: Introduce an internal allocator for
disposable private objects") introduced a regression for the kernel
running as Xen dom0: when switching to graphics mode a GPU HANG
occurred.

Reason seems to be a missing adaption similar to that done in
commit 7453c549f5f648 ("swiotlb: Export swiotlb_max_segment to users")
to i915_gem_object_get_pages_internal().

So limit the maximum page order to be used according to the maximum
swiotlb segment size instead to the complete swiotlb size.

Fixes: 920cf4194954 ("drm/i915: Introduce an internal allocator for disposable private objects")
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170202094711.939-1-jgross@suse.com
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.10-rc1+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 5584f1b1d73e9cc95092734c316e467c6c4468f9)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Flush untouched framebuffers before display on !llc

On a non-llc system, the objects are created with .cache_level =
CACHE_NONE and so the transition to uncached for scanout is a no-op.
However, if the object was never written to, it will still be in the CPU
domain (having been zeroed out by shmemfs). Those cachelines need to be
flushed prior to display.

Reported-and-tested-by: Vito Caputo
Fixes: a6a7cc4b7db6 ("drm/i915: Always flush the dirty CPU cache when pinning the scanout")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.10-rc1+
Link: http://patchwork.freedesktop.org/patch/msgid/20170109111932.6342-1-chris@chris-wilson.co.uk
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 69aeafeae9b30d797c439a30d1a4ccc8dc5b0eb0)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: fix use-after-free in page_flip_completed()

page_flip_completed() dereferences 'work' variable after executing
queue_work(). This is not safe as the 'work' item might be already freed
by queued work:

    BUG: KASAN: use-after-free in page_flip_completed+0x3ff/0x490 at addr ffff8803dc010f90
    Call Trace:
     __asan_report_load8_noabort+0x59/0x80
     page_flip_completed+0x3ff/0x490
     intel_finish_page_flip_mmio+0xe3/0x130
     intel_pipe_handle_vblank+0x2d/0x40
     gen8_irq_handler+0x4a7/0xed0
     __handle_irq_event_percpu+0xf6/0x860
     handle_irq_event_percpu+0x6b/0x160
     handle_irq_event+0xc7/0x1b0
     handle_edge_irq+0x1f4/0xa50
     handle_irq+0x41/0x70
     do_IRQ+0x9a/0x200
     common_interrupt+0x89/0x89

    Freed:
     kfree+0x113/0x4d0
     intel_unpin_work_fn+0x29a/0x3b0
     process_one_work+0x79e/0x1b70
     worker_thread+0x611/0x1460
     kthread+0x241/0x3a0
     ret_from_fork+0x27/0x40

Move queue_work() after trace_i915_flip_complete() to fix this.

Fixes: e5510fac98a7 ("drm/i915: add tracepoints for flip requests & completions")
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: <stable@vger.kernel.org> # v2.6.36+
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126143211.24013-1-aryabinin@virtuozzo.com
(cherry picked from commit 05c41f926fcc7ef838c80a6a99d84f67b4e0b824)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

selinux: fix off-by-one in setprocattr

SELinux tries to support setting/clearing of /proc/pid/attr attributes
from the shell by ignoring terminating newlines and treating an
attribute value that begins with a NUL or newline as an attempt to
clear the attribute.  However, the test for clearing attributes has
always been wrong; it has an off-by-one error, and this could further
lead to reading past the end of the allocated buffer since commit
bb646cdb12e75d82258c2f2e7746d5952d3e321a ("proc_pid_attr_write():
switch to memdup_user()").  Fix the off-by-one error.

Even with this fix, setting and clearing /proc/pid/attr attributes
from the shell is not straightforward since the interface does not
support multiple write() calls (so shells that write the value and
newline separately will set and then immediately clear the attribute,
requiring use of echo -n to set the attribute), whereas trying to use
echo -n "" to clear the attribute causes the shell to skip the
write() call altogether since POSIX says that a zero-length write
causes no side effects. Thus, one must use echo -n to set and echo
without -n to clear, as in the following example:
$ echo -n unconfined_u:object_r:user_home_t:s0 > /proc/$$/attr/fscreate
$ cat /proc/$$/attr/fscreate
unconfined_u:object_r:user_home_t:s0
$ echo "" > /proc/$$/attr/fscreate
$ cat /proc/$$/attr/fscreate

Note the use of /proc/$$ rather than /proc/self, as otherwise
the cat command will read its own attribute value, not that of the shell.

There are no users of this facility to my knowledge; possibly we
should just get rid of it.

UPDATE: Upon further investigation it appears that a local process
with the process:setfscreate permission can cause a kernel panic as a
result of this bug.  This patch fixes CVE-2017-2618.

Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
[PM: added the update about CVE-2017-2618 to the commit description]
Cc: stable@vger.kernel.org # 3.5: d6ea83ec6864e
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>

stacktrace, lockdep: Fix address, newline ugliness

Since KERN_CONT became meaningful again, lockdep stack traces have had
annoying extra newlines, like this:

[    5.561122] -> #1 (B){+.+...}:
[    5.561528]
[    5.561532] [<ffffffff810d8873>] lock_acquire+0xc3/0x210
[    5.562178]
[    5.562181] [<ffffffff816f6414>] mutex_lock_nested+0x74/0x6d0
[    5.562861]
[    5.562880] [<ffffffffa01aa3c3>] init_btrfs_fs+0x21/0x196 [btrfs]
[    5.563717]
[    5.563721] [<ffffffff81000472>] do_one_initcall+0x52/0x1b0
[    5.564554]
[    5.564559] [<ffffffff811a3af6>] do_init_module+0x5f/0x209
[    5.565357]
[    5.565361] [<ffffffff81122f4d>] load_module+0x218d/0x2b80
[    5.566020]
[    5.566021] [<ffffffff81123beb>] SyS_finit_module+0xeb/0x120
[    5.566694]
[    5.566696] [<ffffffff816fd241>] entry_SYSCALL_64_fastpath+0x1f/0xc2

That's happening because each printk() call now gets printed on its own
line, and we do a separate call to print the spaces before the symbol.
Fix it by doing the printk() directly instead of using the
print_ip_sym() helper.

Additionally, the symbol address isn't very helpful, so let's get rid of
that, too. The final result looks like this:

[    5.194518] -> #1 (B){+.+...}:
[    5.195002]        lock_acquire+0xc3/0x210
[    5.195439]        mutex_lock_nested+0x74/0x6d0
[    5.196491]        do_one_initcall+0x52/0x1b0
[    5.196939]        do_init_module+0x5f/0x209
[    5.197355]        load_module+0x218d/0x2b80
[    5.197792]        SyS_finit_module+0xeb/0x120
[    5.198251]        entry_SYSCALL_64_fastpath+0x1f/0xc2

Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kernel-team@fb.com
Fixes: 4bcc595ccd80 ("printk: reinstate KERN_CONT for printing continuation lines")
Link: http://lkml.kernel.org/r/43b4e114724b2bdb0308fa86cb33aa07d3d67fad.1486510315.git.osandov@fb.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge branch 'drm-vmwgfx-fixes-4_10' of git://people.freedesktop.org/~syeh/repos_linux into drm-fixes

Single vmwgfx boot crasher fix.

* 'drm-vmwgfx-fixes-4_10' of git://people.freedesktop.org/~syeh/repos_linux:
drm/vmwgfx: Fix depth input into drm_mode_legacy_fb_format

Input: synaptics-rmi4 - select 'SERIO' when needed

With CONFIG_SERIO=m, we get a build error for the rmi4-f03 driver,
added in linux-4.10:

warning: (HID_RMI) selects RMI4_F03 which has unmet direct dependencies (!UML && INPUT && RMI4_CORE && (SERIO=y || RMI4_CORE=SERIO))
drivers/input/built-in.o: In function `rmi_f03_attention':
rmi_f03.c:(.text+0xcfe0): undefined reference to `serio_interrupt'
rmi_f03.c:(.text+0xd055): undefined reference to `serio_interrupt'
drivers/input/built-in.o: In function `rmi_f03_remove':
rmi_f03.c:(.text+0xd115): undefined reference to `serio_unregister_port'
drivers/input/built-in.o: In function `rmi_f03_probe':
rmi_f03.c:(.text+0xd209): undefined reference to `__serio_register_port'

An earlier patch tried to fix this, but missed the HID_RMI driver that
does a 'select' on the F03 backend.

This adds a hidden Kconfig symbol that enforces 'serio' to be enabled
when RMI4-F03 is, which covers all cases.

Fixes: d7ddad0acc4a ("Input: synaptics-rmi4 - fix F03 build error when serio is module")
Fixes: c5e8848fc98e ("Input: synaptics-rmi4 - add support for F03")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David Miller:

1) Load correct firmware in rtl8192ce wireless driver, from Jurij
    Smakov.

2) Fix leak of tx_ring and tx_cq due to overwriting in mlx4 driver,
    from Martin KaFai Lau.

3) Need to reference count PHY driver module when it is attached, from
    Mao Wenan.

4) Don't do zero length vzalloc() in ethtool register dump, from
    Stanislaw Gruszka.

5) Defer net_disable_timestamp() to a workqueue to get out of locking
    issues, from Eric Dumazet.

6) We cannot drop the SKB dst when IP options refer to them, fix also
    from Eric Dumazet.

7) Incorrect packet header offset calculations in ip6_gre, again from
    Eric Dumazet.

8) Missing tcp_v6_restore_cb() causes use-after-free, from Eric too.

9) tcp_splice_read() can get into an infinite loop with URG, and hey
    it's from Eric once more.

10) vnet_hdr_sz can change asynchronously, so read it once during
    decision making in macvtap and tun, from Willem de Bruijn.

11) Can't use kernel stack for DMA transfers in USB networking drivers,
    from Ben Hutchings.

12) Handle csum errors properly in UDP by calling the proper destructor,
    from Eric Dumazet.

13) For non-deterministic softirq run when scheduling NAPI from a
    workqueue in mlx4, from Benjamin Poirier.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (28 commits)
  sctp: check af before verify address in sctp_addr_id2transport
  sctp: avoid BUG_ON on sctp_wait_for_sndbuf
  mlx4: Invoke softirqs after napi_reschedule
  udp: properly cope with csum errors
  catc: Use heap buffer for memory size test
  catc: Combine failure cleanup code in catc_probe()
  rtl8150: Use heap buffers for all register access
  pegasus: Use heap buffers for all register access
  macvtap: read vnet_hdr_size once
  tun: read vnet_hdr_sz once
  tcp: avoid infinite loop in tcp_splice_read()
  hns: avoid stack overflow with CONFIG_KASAN
  ipv6: Fix IPv6 packet loss in scenarios involving roaming + snooping switches
  ipv6: tcp: add a missing tcp_v6_restore_cb()
  nl80211: Fix mesh HT operation check
  mac80211: Fix adding of mesh vendor IEs
  mac80211: Allocate a sync skcipher explicitly for FILS AEAD
  mac80211: Fix FILS AEAD protection in Association Request frame
  ip6_gre: fix ip6gre_err() invalid reads
  netlabel: out of bound access in cipso_v4_validate()
  ...

mm: fix KPF_SWAPCACHE in /proc/kpageflags

Commit 6326fec1122c ("mm: Use owner_priv bit for PageSwapCache, valid
when PageSwapBacked") aliased PG_swapcache to PG_owner_priv_1 (and
depending on PageSwapBacked being true).

As a result, the KPF_SWAPCACHE bit in '/proc/kpageflags' should now be
synthesized, instead of being shown on unrelated pages which just happen
to have PG_owner_priv_1 set.

Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sctp: check af before verify address in sctp_addr_id2transport

Commit 6f29a1306131 ("sctp: sctp_addr_id2transport should verify the
addr before looking up assoc") invoked sctp_verify_addr to verify the
addr.

But it didn't check af variable beforehand, once users pass an address
with family = 0 through sockopt, sctp_get_af_specific will return NULL
and NULL pointer dereference will be caused by af->sockaddr_len.

This patch is to fix it by returning NULL if af variable is NULL.

Fixes: 6f29a1306131 ("sctp: sctp_addr_id2transport should verify the addr before looking up assoc")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vfio/spapr_tce: Set window when adding additional groups to container

If a container already has a group attached, attaching a new group
should just program already created IOMMU tables to the hardware via
the iommu_table_group_ops::set_window() callback.

However commit 6f01cc692a16 ("vfio/spapr: Add a helper to create
default DMA window") did not just simplify the code but also removed
the set_window() calls in the case of attaching groups to a container
which already has tables so it broke VFIO PCI hotplug.

This reverts set_window() bits in tce_iommu_take_ownership_ddw().

Fixes: 6f01cc692a16 ("vfio/spapr: Add a helper to create default DMA window")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>

ARC: [arcompact] brown paper bag bug in unaligned access delay slot fixup

Reported-by: Jo-Philipp Wich <jo@mein.io>
Fixes: 9aed02feae57bf7 ("ARC: [arcompact] handle unaligned access delay slot")
Cc: linux-kernel@vger.kernel.org
Cc: linux-snps-arc@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sctp: avoid BUG_ON on sctp_wait_for_sndbuf

Alexander Popov reported that an application may trigger a BUG_ON in
sctp_wait_for_sndbuf if the socket tx buffer is full, a thread is
waiting on it to queue more data and meanwhile another thread peels off
the association being used by the first thread.

This patch replaces the BUG_ON call with a proper error handling. It
will return -EPIPE to the original sendmsg call, similarly to what would
have been done if the association wasn't found in the first place.

Acked-by: Alexander Popov <alex.popov@linux.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4: Invoke softirqs after napi_reschedule

mlx4 may schedule napi from a workqueue. Afterwards, softirqs are not run
in a deterministic time frame and the following message may be logged:
NOHZ: local_softirq_pending 08

The problem is the same as what was described in commit ec13ee80145c
("virtio_net: invoke softirqs after __napi_schedule") and this patch
applies the same fix to mlx4.

Fixes: 07841f9d94c1 ("net/mlx4_en: Schedule napi when RX buffers allocation fails")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

udp: properly cope with csum errors

Dmitry reported that UDP sockets being destroyed would trigger the
WARN_ON(atomic_read(&sk->sk_rmem_alloc)); in inet_sock_destruct()

It turns out we do not properly destroy skb(s) that have wrong UDP
checksum.

Thanks again to syzkaller team.

Fixes : 7c13f97ffde6 ("udp: do fwd memory scheduling on dequeue")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>