review.tizen.org Git - platform/kernel/linux-rpi.git/log

fbtft: Fix the initialization from property algorithm

When converting to device property API the commit
8b2d3aeeb7ec ("fbtft: Make use of device property API")
mistakenly placed the reading of the first value inside the loop,
that jumps over value after initialization sequence or sleep commands.

Move the above mentioned reading outside of the loop to restore
correct behaviour.

Besides that, we are using pre-increment operation which may lead to
out of the boundary access at the end of sequence. Thus, allocate buffer
with an additional element at the end to prevent out of the boundary
access.

Fixes: 8b2d3aeeb7ec ("fbtft: Make use of device property API")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191121140207.65089-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8712: fix interface sanity check

Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.

Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.

Fixes: 2865d42c78a9 ("staging: r8712u: Add the new driver to the mainline kernel")
Cc: stable <stable@vger.kernel.org> # 2.6.37
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191210114751.5119-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: fix interface sanity check

Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.

Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.

Fixes: c2478d39076b ("staging: r8188eu: Add files for new driver - part 20")
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191210114751.5119-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: gigaset: add endpoint-type sanity check

Add missing endpoint-type sanity checks to probe.

This specifically prevents a warning in USB core on URB submission when
fuzzing USB descriptors.

Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191202085610.12719-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: gigaset: fix illegal free on probe errors

The driver failed to initialise its receive-buffer pointer, something
which could lead to an illegal free on late probe errors.

Fix this by making sure to clear all driver data at allocation.

Fixes: 2032e2c2309d ("usb_gigaset: code cleanup")
Cc: stable <stable@vger.kernel.org> # 2.6.33
Cc: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191202085610.12719-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: gigaset: fix general protection fault on probe

Fix a general protection fault when accessing the endpoint descriptors
which could be triggered by a malicious device due to missing sanity
checks on the number of endpoints.

Reported-by: syzbot+35b1c403a14f5c89eba7@syzkaller.appspotmail.com
Fixes: 07dc1f9f2f80 ("[PATCH] isdn4linux: Siemens Gigaset drivers - M105 USB DECT adapter")
Cc: stable <stable@vger.kernel.org> # 2.6.17
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191202085610.12719-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vchiq: call unregister_chrdev_region() when driver registration fails

This undoes the previous call to alloc_chrdev_region() on failure,
and is probably what was meant originally given the label name.

Signed-off-by: Marcelo Diop-Gonzalez <marcgonzalez@google.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 187ac53e590c ("staging: vchiq_arm: rework probe and init functions")
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20191203153921.70540-1-marcgonzalez@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: fix multiple definition error of `rename_file'

`rename_file' was exported but not properly namespaced causing a
multiple definition error because `rename_file' is already defined in
fs/hostfs/hostfs_user.c:

ld: drivers/staging/exfat/exfat_core.o: in function `rename_file':
drivers/staging/exfat/exfat_core.c:2327: multiple definition of
`rename_file'; fs/hostfs/hostfs_user.o:fs/hostfs/hostfs_user.c:350:
first defined here
make: *** [Makefile:1077: vmlinux] Error 1

This error can be reproduced on ARCH=um by selecting:

CONFIG_EXFAT_FS=y
CONFIG_HOSTFS=y

Add a namespace prefix exfat_* to fix this error.

Reported-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Cc: stable <stable@vger.kernel.org>
Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Tested-by: David Gow <davidgow@google.com>
Reviewed-by: David Gow <davidgow@google.com>
Link: https://lore.kernel.org/r/20191204234522.42855-1-brendanhiggins@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/wlan-ng: add CRC32 dependency in Kconfig

wlan-ng uses the function crc32_le,
but CRC32 wasn't a dependency of wlan-ng

Co-developed-by: Michael Kupfer <michael.kupfer@fau.de>
Signed-off-by: Michael Kupfer <michael.kupfer@fau.de>
Signed-off-by: Kay Friedrich <kay.friedrich@fau.de>
Link: https://lore.kernel.org/r/20191127112457.2301-1-kay.friedrich@fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: hp100: Fix build error without ETHERNET

It should depends on ETHERNET, otherwise building fails:

drivers/staging/hp/hp100.o: In function `hp100_pci_remove':
hp100.c:(.text+0x165): undefined reference to `unregister_netdev'
hp100.c:(.text+0x214): undefined reference to `free_netdev'

Fixes: 52340b82cf1a ("hp100: Move 100BaseVG AnyLAN driver to staging")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20191113021306.35464-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: fbtft: Do not hardcode SPI CS polarity inversion

The current use of the mode flag SPI_CS_HIGH is fragile: it
overwrites anything already assigned by the SPI core.

Assign ^= SPI_CS_HIGH since we might be active high
already, and that is usually the case with GPIOs used
for chip select, even if they are in practice active low.

Add a comment clarifying why ^= SPI_CS_HIGH is the right
choice here.

Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191204233230.22309-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: properly support discard in clr_alloc_bitmap()

Currently the discard code in clr_alloc_bitmap() is just dead code.
Move code around so that the discard operation is properly attempted
when enabled.

Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Link: https://lore.kernel.org/r/20191205152913.GJ3276@xps-13
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/octeon: Mark Ethernet driver as BROKEN

The code doesn't compile due to incompatible pointer errors such as

drivers/staging/octeon/ethernet-tx.c:649:50: error:
passing argument 1 of 'cvmx_wqe_get_grp' from incompatible pointer type

This is due to mixing, for example, cvmx_wqe_t with 'struct cvmx_wqe'.

Unfortunately, one can not just revert the primary offending commit, as doing so
results in secondary errors. This is made worse by the fact that the "removed"
typedefs still exist and are used widely outside the staging directory,
making the entire set of "remove typedef" changes pointless and wrong.

Reflect reality and mark the driver as BROKEN.

Fixes: ef1fe6b7369a ("staging: octeon: remove typedef declaration for cvmx_wqe")
Fixes: 73aef0c9d2c6 ("staging: octeon: remove typedef declaration for cvmx_helper_link_info")
Cc: Wambui Karuga <wambui.karugax@gmail.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191202141836.9363-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'iio-fixes-for-5.5a' of git://git./linux/kernel/git/jic23/iio into staging-linus

Jonathan writes:

First set of fixes for IIO in the 5.5 cycle.

Mixture of old things people have just hit, and a few late breaking
issues with things that went in during the merge window.

Being sent promptly to resolve potential DT breakage causing
issues for binding test builds.

* ad7606
  - Avoid reading extra data from the device over what was intended.
* ad7124
  - Enable the internal reference when in use.
* ad7292
  - Fix up license for newly added binding.  Better to not have this go
    out in a release with more limited header than intended.
  - Fix a constraint on number of channels.
* ad7949
  - Fix an issue which can result in readouts being from the wrong channel.
* hdc100x
  - Fix wrong ABI usage (units) for relative humidity channel.
* intel mrfld
  - Allocate right amount of private data (currently allocating too much).
* ltc2983
  - Avoid a potential issue with machine endianness and wrong length device
    tree read.
* max1027
  - Clean up leak of an iio_trigger on probe failure.
* max9611
  - Ensure we sleep long enough to successfully initialize the sensor.
* mpu6050
  - Fix wrong ABI usage (units) for temperature channel.
* st_accel
  - Fix an unused variable warning.
* st_lsm6dsx
  - Fix decimation factor issue that can lead to missaligned datasets
    (and hence garbage)
  - Fix an issue with how we track enabled fifo channels.
  - Avoid powering off the device if wake up events are enabled.

* tag 'iio-fixes-for-5.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
  iio: adc: max9611: Fix too short conversion time delay
  iio: ad7949: fix channels mixups
  iio: imu: st_lsm6dsx: do not power-off accel if events are enabled
  iio: imu: st_lsm6dsx: track hw FIFO buffering with fifo_mask
  iio: imu: st_lsm6dsx: fix decimation factor estimation
  iio: imu: inv_mpu6050: fix temperature reporting using bad unit
  iio: humidity: hdc100x: fix IIO_HUMIDITYRELATIVE channel reporting
  iio: adc: max1027: fix not unregistered iio trigger
  iio: adc: intel_mrfld_adc: Allocating too much data in probe()
  iio: adc: ad7124: Enable internal reference
  dt-bindings: iio: adc: ad7292: fix constraint over channel quantity
  dt-bindings: iio: adc: ad7292: Update SPDX identifier
  iio: temperature: ltc2983: fix u32 read into a unsigned long long
  iio: st_accel: Fix unused variable warning
  iio: adc: ad7606: fix reading unnecessary data from device

Linux 5.5-rc1

Merge git://git./linux/kernel/git/netdev/net

Pull networking fixes from David Miller:

1) More jumbo frame fixes in r8169, from Heiner Kallweit.

2) Fix bpf build in minimal configuration, from Alexei Starovoitov.

3) Use after free in slcan driver, from Jouni Hogander.

4) Flower classifier port ranges don't work properly in the HW offload
    case, from Yoshiki Komachi.

5) Use after free in hns3_nic_maybe_stop_tx(), from Yunsheng Lin.

6) Out of bounds access in mqprio_dump(), from Vladyslav Tarasiuk.

7) Fix flow dissection in dsa TX path, from Alexander Lobakin.

8) Stale syncookie timestampe fixes from Guillaume Nault.

[ Did an evil merge to silence a warning introduced by this pull - Linus ]

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
  r8169: fix rtl_hw_jumbo_disable for RTL8168evl
  net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add()
  r8169: add missing RX enabling for WoL on RTL8125
  vhost/vsock: accept only packets with the right dst_cid
  net: phy: dp83867: fix hfs boot in rgmii mode
  net: ethernet: ti: cpsw: fix extra rx interrupt
  inet: protect against too small mtu values.
  gre: refetch erspan header from skb->data after pskb_may_pull()
  pppoe: remove redundant BUG_ON() check in pppoe_pernet
  tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE()
  tcp: tighten acceptance of ACKs not matching a child socket
  tcp: fix rejected syncookies due to stale timestamps
  lpc_eth: kernel BUG on remove
  tcp: md5: fix potential overestimation of TCP option space
  net: sched: allow indirect blocks to bind to clsact in TC
  net: core: rename indirect block ingress cb function
  net-sysfs: Call dev_hold always in netdev_queue_add_kobject
  net: dsa: fix flow dissection on Tx path
  net/tls: Fix return values to avoid ENOTSUPP
  net: avoid an indirect call in ____sys_recvmsg()
  ...

Merge tag 'scsi-misc' of git://git./linux/kernel/git/jejb/scsi

Pull more SCSI updates from James Bottomley:
"Eleven patches, all in drivers (no core changes) that are either minor
  cleanups or small fixes.

  They were late arriving, but still safe for -rc1"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: MAINTAINERS: Add the linux-scsi mailing list to the ISCSI entry
  scsi: megaraid_sas: Make poll_aen_lock static
  scsi: sd_zbc: Improve report zones error printout
  scsi: qla2xxx: Fix qla2x00_request_irqs() for MSI
  scsi: qla2xxx: unregister ports after GPN_FT failure
  scsi: qla2xxx: fix rports not being mark as lost in sync fabric scan
  scsi: pm80xx: Remove unused include of linux/version.h
  scsi: pm80xx: fix logic to break out of loop when register value is 2 or 3
  scsi: scsi_transport_sas: Fix memory leak when removing devices
  scsi: lpfc: size cpu map by last cpu id set
  scsi: ibmvscsi_tgt: Remove unneeded variable rc

Merge tag '5.5-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6

Pull cifs fixes from Steve French:
"Nine cifs/smb3 fixes:

   - one fix for stable (oops during oplock break)

   - two timestamp fixes including important one for updating mtime at
     close to avoid stale metadata caching issue on dirty files (also
     improves perf by using SMB2_CLOSE_FLAG_POSTQUERY_ATTRIB over the
     wire)

   - two fixes for "modefromsid" mount option for file create (now
     allows mode bits to be set more atomically and accurately on create
     by adding "sd_context" on create when modefromsid specified on
     mount)

   - two fixes for multichannel found in testing this week against
     different servers

   - two small cleanup patches"

* tag '5.5-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: improve check for when we send the security descriptor context on create
  smb3: fix mode passed in on create for modetosid mount option
  cifs: fix possible uninitialized access and race on iface_list
  cifs: Fix lookup of SMB connections on multichannel
  smb3: query attributes on file close
  smb3: remove unused flag passed into close functions
  cifs: remove redundant assignment to pointer pneg_ctxt
  fs: cifs: Fix atime update check vs mtime
  CIFS: Fix NULL-pointer dereference in smb2_push_mandatory_locks

Merge branch 'work.misc' of git://git./linux/kernel/git/viro/vfs

Pull misc vfs cleanups from Al Viro:
"No common topic, just three cleanups".

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  make __d_alloc() static
  fs/namespace: add __user to open_tree and move_mount syscalls
  fs/fnctl: fix missing __user in fcntl_rw_hint()

iio: adc: max9611: Fix too short conversion time delay

As of commit b9ddd5091160793e ("iio: adc: max9611: Fix temperature
reading in probe"), max9611 initialization sometimes fails on the
Salvator-X(S) development board with:

    max9611 4-007f: Invalid value received from ADC 0x8000: aborting
    max9611: probe of 4-007f failed with error -5

The max9611 driver tests communications with the chip by reading the die
temperature during the probe function, which returns an invalid value.

According to the datasheet, the typical ADC conversion time is 2 ms, but
no minimum or maximum values are provided.  Maxim Technical Support
confirmed this was tested with temperature Ta=25 degreeC, and promised
to inform me if a maximum/minimum value is available (they didn't get
back to me, so I assume it is not).

However, the driver assumes a 1 ms conversion time.  Usually the
usleep_range() call returns after more than 1.8 ms, hence it succeeds.
When it returns earlier, the data register may be read too early, and
the previous measurement value will be returned.  After boot, this is
the temperature POR (power-on reset) value, causing the failure above.

Fix this by increasing the delay from 1000-2000 µs to 3000-3300 µs.

Note that this issue has always been present, but it was exposed by the
aformentioned commit.

Fixes: 69780a3bbc0b1e7e ("iio: adc: Add Maxim max9611 ADC driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: ad7949: fix channels mixups

Each time we need to read a sample (from the sysfs interface, since the
driver supports only it) the driver writes the configuration register
with the proper settings needed to perform the said read, then it runs
another xfer to actually read the resulting value. Most notably the
configuration register is updated to set the ADC internal MUX depending by
which channel the read targets.

Unfortunately this seems not enough to ensure correct operation because
the ADC works in a pipelined-like fashion and the new configuration isn't
applied in time.

The ADC alternates two phases: acquisition and conversion. During the
acquisition phase the ADC samples the analog signal in an internal
capacitor; in the conversion phase the ADC performs the actual analog to
digital conversion of the stored voltage. Note that of course the MUX
needs to be set to the proper channel when the acquisition phase is
performed.

Once the conversion phase has been completed, the device automatically
switches back to a new acquisition; on the other hand the device switches
from acquisition to conversion on the rising edge of SPI cs signal (that
is when the xfer finishes).

Only after both two phases have been completed (with the proper settings
already written in the configuration register since the beginning) it is
possible to read the outcome from SPI bus.

With the current driver implementation, we end up in the following
situation:

        _______  1st xfer ____________  2nd xfer ___________________
SPI cs..       \_________/            \_________/
SPI rd.. idle  |(val N-2)+    idle    | val N-1 +   idle ...
SPI wr.. idle  |  cfg N  +    idle    |   (X)   +   idle ...
------------------------ + -------------------- + ------------------
  AD  ..   acq  N-1      + cnv N-1 |  acq N     +  cnv N  | acq N+1

As shown in the diagram above, the value we read in the Nth read belongs
to configuration setting N-1.

In case the configuration is not changed (config[N] == config[N-1]), then
we still get correct data, but in case the configuration changes (i.e.
switching the MUX on another channel), we get wrong data (data from the
previously selected channel).

This patch fixes this by performing one more "dummy" transfer in order to
ending up in reading the data when it's really ready, as per the following
timing diagram.

        _______  1st xfer ____________  2nd xfer ___________  3rd xfer ___
SPI cs..       \_________/            \_________/           \_________/
SPI rd.. idle  |(val N-2)+    idle    |(val N-1)+    idle   |  val N  + ..
SPI wr.. idle  |  cfg N  +    idle    |   (X)   +    idle   |   (X)   + ..
------------------------ + -------------------- + ------------------- + --
  AD  ..   acq  N-1      + cnv N-1 |  acq N     +  cnv N  | acq N+1   | ..

NOTE: in the latter case (cfg changes), the acquisition phase for the
value to be read begins after the 1st xfer, that is after the read request
has been issued on sysfs. On the other hand, if the cfg doesn't change,
then we can refer to the fist diagram assuming N == (N - 1); the
acquisition phase _begins_ before the 1st xfer (potentially a lot of time
before the read has been issued via sysfs, but it _ends_ after the 1st
xfer, that is _after_ the read has started. This should guarantee a
reasonably fresh data, which value represents the voltage that the sampled
signal has after the read start or maybe just around it.

Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: st_lsm6dsx: do not power-off accel if events are enabled

Do not power-off accel unconditionally if wake-up events are enabled
powering off the hw FIFO. At the same time do not power-off the accel
sensor if it is 'batched' in the hw FIFO disabling sensor events

Fixes: b5969abfa8b8 ("iio: imu: st_lsm6dsx: add motion events")
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: st_lsm6dsx: track hw FIFO buffering with fifo_mask

Track hw FIFO state introducing fifo_mask since now the accel sensor
can be enabled during suspend/resume in order to trigger the wake-up
enabling the FIFO in st_lsm6dsx_resume even if it was disabled before
the suspend. Hence we must separately track the fifo state.

Fixes: 4c997dfa692d ("iio: imu: st_lsm6dsx: add wakeup-source option")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: st_lsm6dsx: fix decimation factor estimation

Fix decimation factor and sip estimation for LSM6DSM series
(max value for decimation factor is 32).
If gyro and accel sensors are enabled at 12.5Hz and 416Hz
respectively, decimation factor lookup will fail, producing
unaligned data.
Remove unused decimator filed in st_lsm6dsx_sensor structure.

Fixes: f8710f0357bc ("iio: imu: st_lsm6dsx: express odr in mHZ")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: inv_mpu6050: fix temperature reporting using bad unit

Temperature should be reported in milli-degrees, not degrees. Fix
scale and offset values to use the correct unit.

This is a fix for an issue that has been present for a long time.
The fixes tag reflects the point at which the code last changed in a
fashion that would make this fix patch no longer apply. Backports
will be necessary to fix those elements that predate that patch.

Fixes: 1615fe41a195 ("iio: imu: mpu6050: Fix FIFO layout for ICM20602")
Cc: stable@vger.kernel.org
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: humidity: hdc100x: fix IIO_HUMIDITYRELATIVE channel reporting

The IIO_HUMIDITYRELATIVE channel was being incorrectly reported back
as percent when it should have been milli percent. This is via an
incorrect scale value being returned to userspace.

Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: max1027: fix not unregistered iio trigger

The driver forgets to unregister the iio trigger in probe failure and
remove.
Use devm API to fix it.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: intel_mrfld_adc: Allocating too much data in probe()

This probe function is passing the wrong size to devm_iio_device_alloc().
It is supposed to be the size of the private data. Fortunately,
sizeof(*indio_dev) is larger than sizeof(struct mrfld_adc) so it doesn't
cause a runtime problem.

Fixes: a7118662734a ("iio: adc: intel_mrfld_adc: Add Basin Cove ADC driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad7124: Enable internal reference

When the internal reference was selected by a channel it was not enabled.
This patch fixes that and enables it.

Fixes: b3af341bbd96 ("iio: adc: Add ad7124 support")
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: adc: ad7292: fix constraint over channel quantity

Change items property of AD7292 channels to correctly constrain their
quantity.

Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: adc: ad7292: Update SPDX identifier

Update SPDX identifier to the preferred dual GPL-2.0 OR BSD-2-Clause
licensing.

Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: temperature: ltc2983: fix u32 read into a unsigned long long

Currently the read of temp using of_property_read_u32_index is reading
a u32 value into a unsigned long long. This relies on machine endianness
to work correctly, so fix this by reading a u32 value and setting temp
to this value.

Addresses-Coverity: ("Reliance on integer endianness")
Fixes: f110f3188e56 ("iio: temperature: Add support for LTC2983")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: st_accel: Fix unused variable warning

drivers/iio/accel/st_accel_core.c:1005:44: warning:
mount_matrix_ext_info defined but not used [-Wunused-const-variable=]

Using stub helper while CONFIG_ACPI is disabled to fix it.

Suggested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad7606: fix reading unnecessary data from device

When a conversion result is being read from ADC, the driver reads the
number of channels + 1 because it thinks that IIO_CHAN_SOFT_TIMESTAMP
is also a physical channel. This patch fixes this issue.

Fixes: 2985a5d88455 ("staging: iio: adc: ad7606: Move out of staging")
Reported-by: Robert Wörle <rwoerle@mibtec.de>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Merge tag 'ntb-5.5' of git://github.com/jonmason/ntb

Pull NTB update from Jon Mason:
"Just a simple patch to add a new Hygon Device ID to the AMD NTB device
driver"

* tag 'ntb-5.5' of git://github.com/jonmason/ntb:
NTB: Add Hygon Device ID

Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input

Pull more input updates from Dmitry Torokhov:

- fixups for Synaptics RMI4 driver

- a quirk for Goodinx touchscreen on Teclast tablet

- a new keycode definition for activating privacy screen feature found
   on a few "enterprise" laptops

- updates to snvs_pwrkey driver

- polling uinput device for writing (which is always allowed) now works

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers
  Input: synaptics-rmi4 - re-enable IRQs in f34v7_do_reflash
  Input: goodix - add upside-down quirk for Teclast X89 tablet
  Input: add privacy screen toggle keycode
  Input: uinput - fix returning EPOLLOUT from uinput_poll
  Input: snvs_pwrkey - remove gratuitous NULL initializers
  Input: snvs_pwrkey - send key events for i.MX6 S, DL and Q

Merge tag 'iomap-5.5-merge-14' of git://git./fs/xfs/xfs-linux

Pull iomap fixes from Darrick Wong:
"Fix a race condition and a use-after-free error:

   - Fix a UAF when reporting writeback errors

   - Fix a race condition when handling page uptodate on fragmented file
     with blocksize < pagesize"

* tag 'iomap-5.5-merge-14' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  iomap: stop using ioend after it's been freed in iomap_finish_ioend()
  iomap: fix sub-page uptodate handling

Merge tag 'xfs-5.5-merge-17' of git://git./fs/xfs/xfs-linux

Pull xfs fixes from Darrick Wong:
"Fix a couple of resource management errors and a hang:

   - fix a crash in the log setup code when log mounting fails

   - fix a hang when allocating space on the realtime device

   - fix a block leak when freeing space on the realtime device"

* tag 'xfs-5.5-merge-17' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: fix mount failure crash on invalid iclog memory access
  xfs: don't check for AG deadlock for realtime files in bunmapi
  xfs: fix realtime file data space leak

Merge tag 'for-linus-5.5-ofs1' of git://git./linux/kernel/git/hubcap/linux

Pull orangefs update from Mike Marshall:
"orangefs: posix open permission checking...

  Orangefs has no open, and orangefs checks file permissions on each
  file access. Posix requires that file permissions be checked on open
  and nowhere else. Orangefs-through-the-kernel needs to seem posix
  compliant.

  The VFS opens files, even if the filesystem provides no method. We can
  see if a file was successfully opened for read and or for write by
  looking at file->f_mode.

  When writes are flowing from the page cache, file is no longer
  available. We can trust the VFS to have checked file->f_mode before
  writing to the page cache.

  The mode of a file might change between when it is opened and IO
  commences, or it might be created with an arbitrary mode.

  We'll make sure we don't hit EACCES during the IO stage by using
  UID 0"

[ This is "posixish", but not a great solution in the long run, since a
  proper secure network server shouldn't really trust the client like this.
  But proper and secure POSIX behavior requires an open method and a
  resulting cookie for IO of some kind, or similar.    - Linus ]

* tag 'for-linus-5.5-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
  orangefs: posix open permission checking...

Merge tag 'nfsd-5.5' of git://linux-nfs.org/~bfields/linux

Pull nfsd updates from Bruce Fields:
"This is a relatively quiet cycle for nfsd, mainly various bugfixes.

  Possibly most interesting is Trond's fixes for some callback races
  that were due to my incomplete understanding of rpc client shutdown.
  Unfortunately at the last minute I've started noticing a new
  intermittent failure to send callbacks. As the logic seems basically
  correct, I'm leaving Trond's patches in for now, and hope to find a
  fix in the next week so I don't have to revert those patches"

* tag 'nfsd-5.5' of git://linux-nfs.org/~bfields/linux: (24 commits)
  nfsd: depend on CRYPTO_MD5 for legacy client tracking
  NFSD fixing possible null pointer derefering in copy offload
  nfsd: check for EBUSY from vfs_rmdir/vfs_unink.
  nfsd: Ensure CLONE persists data and metadata changes to the target file
  SUNRPC: Fix backchannel latency metrics
  nfsd: restore NFSv3 ACL support
  nfsd: v4 support requires CRYPTO_SHA256
  nfsd: Fix cld_net->cn_tfm initialization
  lockd: remove __KERNEL__ ifdefs
  sunrpc: remove __KERNEL__ ifdefs
  race in exportfs_decode_fh()
  nfsd: Drop LIST_HEAD where the variable it declares is never used.
  nfsd: document callback_wq serialization of callback code
  nfsd: mark cb path down on unknown errors
  nfsd: Fix races between nfsd4_cb_release() and nfsd4_shutdown_callback()
  nfsd: minor 4.1 callback cleanup
  SUNRPC: Fix svcauth_gss_proxy_init()
  SUNRPC: Trace gssproxy upcall results
  sunrpc: fix crash when cache_head become valid before update
  nfsd: remove private bin2hex implementation
  ...

Merge tag 'nfs-for-5.5-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs

Pull NFS client updates from Trond Myklebust:
"Highlights include:

  Features:

   - NFSv4.2 now supports cross device offloaded copy (i.e. offloaded
     copy of a file from one source server to a different target
     server).

   - New RDMA tracepoints for debugging congestion control and Local
     Invalidate WRs.

  Bugfixes and cleanups

   - Drop the NFSv4.1 session slot if nfs4_delegreturn_prepare waits for
     layoutreturn

   - Handle bad/dead sessions correctly in nfs41_sequence_process()

   - Various bugfixes to the delegation return operation.

   - Various bugfixes pertaining to delegations that have been revoked.

   - Cleanups to the NFS timespec code to avoid unnecessary conversions
     between timespec and timespec64.

   - Fix unstable RDMA connections after a reconnect

   - Close race between waking an RDMA sender and posting a receive

   - Wake pending RDMA tasks if connection fails

   - Fix MR list corruption, and clean up MR usage

   - Fix another RPCSEC_GSS issue with MIC buffer space"

* tag 'nfs-for-5.5-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (79 commits)
  SUNRPC: Capture completion of all RPC tasks
  SUNRPC: Fix another issue with MIC buffer space
  NFS4: Trace lock reclaims
  NFS4: Trace state recovery operation
  NFSv4.2 fix memory leak in nfs42_ssc_open
  NFSv4.2 fix kfree in __nfs42_copy_file_range
  NFS: remove duplicated include from nfs4file.c
  NFSv4: Make _nfs42_proc_copy_notify() static
  NFS: Fallocate should use the nfs4_fattr_bitmap
  NFS: Return -ETXTBSY when attempting to write to a swapfile
  fs: nfs: sysfs: Remove NULL check before kfree
  NFS: remove unneeded semicolon
  NFSv4: add declaration of current_stateid
  NFSv4.x: Drop the slot if nfs4_delegreturn_prepare waits for layoutreturn
  NFSv4.x: Handle bad/dead sessions correctly in nfs41_sequence_process()
  nfsv4: Move NFSPROC4_CLNT_COPY_NOTIFY to end of list
  SUNRPC: Avoid RPC delays when exiting suspend
  NFS: Add a tracepoint in nfs_fh_to_dentry()
  NFSv4: Don't retry the GETATTR on old stateid in nfs4_delegreturn_done()
  NFSv4: Handle NFS4ERR_OLD_STATEID in delegreturn
  ...

smb3: improve check for when we send the security descriptor context on create

We had cases in the previous patch where we were sending the security
descriptor context on SMB3 open (file create) in cases when we hadn't
mounted with with "modefromsid" mount option.

Add check for that mount flag before calling ad_sd_context in
open init.

Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>

Merge tag 'vfio-v5.5-rc1' of git://github.com/awilliam/linux-vfio

Pull VFIO updates from Alex Williamson:

- Remove hugepage checks for reserved pfns (Ben Luo)

- Fix irq-bypass unregister ordering (Jiang Yi)

* tag 'vfio-v5.5-rc1' of git://github.com/awilliam/linux-vfio:
vfio/pci: call irq_bypass_unregister_producer() before freeing irq
vfio/type1: remove hugepage checks in is_invalid_reserved_pfn()

Merge tag 'for-linus-5.5b-rc1-tag' of git://git./linux/kernel/git/xen/tip

Pull more xen updates from Juergen Gross:

- a patch to fix a build warning

- a cleanup of no longer needed code in the Xen event handling

- a small series for the Xen grant driver avoiding high order
   allocations and replacing an insane global limit by a per-call one

- a small series fixing Xen frontend/backend module referencing

* tag 'for-linus-5.5b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen-blkback: allow module to be cleanly unloaded
  xen/xenbus: reference count registered modules
  xen/gntdev: switch from kcalloc() to kvcalloc()
  xen/gntdev: replace global limit of mapped pages by limit per call
  xen/gntdev: remove redundant non-zero check on ret
  xen/events: remove event handling recursion detection

Merge branch 'akpm' (patches from Andrew)

Merge misc Kconfig updates from Andrew Morton:
"A number of changes to Kconfig files under lib/ from Changbin Du and
  Krzysztof Kozlowski"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  lib/: fix Kconfig indentation
  kernel-hacking: move DEBUG_FS to 'Generic Kernel Debugging Instruments'
  kernel-hacking: move DEBUG_BUGVERBOSE to 'printk and dmesg options'
  kernel-hacking: create a submenu for scheduler debugging options
  kernel-hacking: move SCHED_STACK_END_CHECK after DEBUG_STACK_USAGE
  kernel-hacking: move Oops into 'Lockups and Hangs'
  kernel-hacking: move kernel testing and coverage options to same submenu
  kernel-hacking: group kernel data structures debugging together
  kernel-hacking: create submenu for arch special debugging options
  kernel-hacking: group sysrq/kgdb/ubsan into 'Generic Kernel Debugging Instruments'

r8169: fix rtl_hw_jumbo_disable for RTL8168evl

In referenced fix we removed the RTL8168e-specific jumbo config for
RTL8168evl in rtl_hw_jumbo_enable(). We have to do the same in
rtl_hw_jumbo_disable().

v2: fix referenced commit id

Fixes: 14012c9f3bb9 ("r8169: fix jumbo configuration for RTL8168evl")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pipe: don't use 'pipe_wait() for basic pipe IO

pipe_wait() may be simple, but since it relies on the pipe lock, it
means that we have to do the wakeup while holding the lock. That's
unfortunate, because the very first thing the waked entity will want to
do is to get the pipe lock for itself.

So get rid of the pipe_wait() usage by simply releasing the pipe lock,
doing the wakeup (if required) and then using wait_event_interruptible()
to wait on the right condition instead.

wait_event_interruptible() handles races on its own by comparing the
wakeup condition before and after adding itself to the wait queue, so
you can use an optimistic unlocked condition for it.

Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

NTB: Add Hygon Device ID

Signed-off-by: Jiasen Lin <linjiasen@hygon.cn>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

pipe: remove 'waiting_writers' merging logic

This code is ancient, and goes back to when we only had a single page
for the pipe buffers. The exact history is hidden in the mists of time
(ie "before git", and in fact predates the BK repository too).

At that long-ago point in time, it actually helped to try to merge big
back-and-forth pipe reads and writes, and not limit pipe reads to the
single pipe buffer in length just because that was all we had at a time.

However, since then we've expanded the pipe buffers to multiple pages,
and this logic really doesn't seem to make sense. And a lot of it is
somewhat questionable (ie "hmm, the user asked for a non-blocking read,
but we see that there's a writer pending, so let's wait anyway to get
the extra data that the writer will have").

But more importantly, it makes the "go to sleep" logic much less
obvious, and considering the wakeup issues we've had, I want to make for
less of those kinds of things.

Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pipe: fix and clarify pipe read wakeup logic

This is the read side version of the previous commit: it simplifies the
logic to only wake up waiting writers when necessary, and makes sure to
use a synchronous wakeup. This time not so much for GNU make jobserver
reasons (that pipe never fills up), but simply to get the writer going
quickly again.

A bit less verbose commentary this time, if only because I assume that
the write side commentary isn't going to be ignored if you touch this
code.

Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pipe: fix and clarify pipe write wakeup logic

The pipe rework ends up having been extra painful, partly becaused of
actual bugs with ordering and caching of the pipe state, but also
because of subtle performance issues.

In particular, the pipe rework caused the kernel build to inexplicably
slow down.

The reason turns out to be that the GNU make jobserver (which limits the
parallelism of the build) uses a pipe to implement a "token" system: a
parallel submake will read a character from the pipe to get the job
token before starting a new job, and will write a character back to the
pipe when it is done. The overall job limit is thus easily controlled
by just writing the appropriate number of initial token characters into
the pipe.

But to work well, that really means that the old behavior of write
wakeups being synchronous (WF_SYNC) is very important - when the pipe
writer wakes up a reader, we want the reader to actually get scheduled
immediately. Otherwise you lose the parallelism of the build.

The pipe rework lost that synchronous wakeup on write, and we had
clearly all forgotten the reasons and rules for it.

This rewrites the pipe write wakeup logic to do the required Wsync
wakeups, but also clarifies the logic and avoids extraneous wakeups.

It also ends up addign a number of comments about what oit does and why,
so that we hopefully don't end up forgetting about this next time we
change this code.

Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add()

Use the new tcf_proto_check_kind() helper to make sure user
provided value is well formed.

BUG: KMSAN: uninit-value in string_nocheck lib/vsprintf.c:606 [inline]
BUG: KMSAN: uninit-value in string+0x4be/0x600 lib/vsprintf.c:668
CPU: 0 PID: 12358 Comm: syz-executor.1 Not tainted 5.4.0-rc8-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x220 lib/dump_stack.c:118
kmsan_report+0x128/0x220 mm/kmsan/kmsan_report.c:108
__msan_warning+0x64/0xc0 mm/kmsan/kmsan_instr.c:245
string_nocheck lib/vsprintf.c:606 [inline]
string+0x4be/0x600 lib/vsprintf.c:668
vsnprintf+0x218f/0x3210 lib/vsprintf.c:2510
__request_module+0x2b1/0x11c0 kernel/kmod.c:143
tcf_proto_lookup_ops+0x171/0x700 net/sched/cls_api.c:139
tc_chain_tmplt_add net/sched/cls_api.c:2730 [inline]
tc_ctl_chain+0x1904/0x38a0 net/sched/cls_api.c:2850
rtnetlink_rcv_msg+0x115a/0x1580 net/core/rtnetlink.c:5224
netlink_rcv_skb+0x431/0x620 net/netlink/af_netlink.c:2477
rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:5242
netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline]
netlink_unicast+0xf3e/0x1020 net/netlink/af_netlink.c:1328
netlink_sendmsg+0x110f/0x1330 net/netlink/af_netlink.c:1917
sock_sendmsg_nosec net/socket.c:637 [inline]
sock_sendmsg net/socket.c:657 [inline]
___sys_sendmsg+0x14ff/0x1590 net/socket.c:2311
__sys_sendmsg net/socket.c:2356 [inline]
__do_sys_sendmsg net/socket.c:2365 [inline]
__se_sys_sendmsg+0x305/0x460 net/socket.c:2363
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2363
do_syscall_64+0xb6/0x160 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x45a649
Code: ad b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f0790795c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 000000000045a649
RDX: 0000000000000000 RSI: 0000000020000300 RDI: 0000000000000006
RBP: 000000000075bfc8 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f07907966d4
R13: 00000000004c8db5 R14: 00000000004df630 R15: 00000000ffffffff

Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:149 [inline]
kmsan_internal_poison_shadow+0x5c/0x110 mm/kmsan/kmsan.c:132
kmsan_slab_alloc+0x97/0x100 mm/kmsan/kmsan_hooks.c:86
slab_alloc_node mm/slub.c:2773 [inline]
__kmalloc_node_track_caller+0xe27/0x11a0 mm/slub.c:4381
__kmalloc_reserve net/core/skbuff.c:141 [inline]
__alloc_skb+0x306/0xa10 net/core/skbuff.c:209
alloc_skb include/linux/skbuff.h:1049 [inline]
netlink_alloc_large_skb net/netlink/af_netlink.c:1174 [inline]
netlink_sendmsg+0x783/0x1330 net/netlink/af_netlink.c:1892
sock_sendmsg_nosec net/socket.c:637 [inline]
sock_sendmsg net/socket.c:657 [inline]
___sys_sendmsg+0x14ff/0x1590 net/socket.c:2311
__sys_sendmsg net/socket.c:2356 [inline]
__do_sys_sendmsg net/socket.c:2365 [inline]
__se_sys_sendmsg+0x305/0x460 net/socket.c:2363
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2363
do_syscall_64+0xb6/0x160 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: 6f96c3c6904c ("net_sched: fix backward compatibility for TCA_KIND")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: add missing RX enabling for WoL on RTL8125

RTL8125 also requires to enable RX for WoL.

v2: add missing Fixes tag

Fixes: f1bce4ad2f1c ("r8169: add support for RTL8125")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vhost/vsock: accept only packets with the right dst_cid

When we receive a new packet from the guest, we check if the
src_cid is correct, but we forgot to check the dst_cid.

The host should accept only packets where dst_cid is
equal to the host CID.

Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: dp83867: fix hfs boot in rgmii mode

The commit ef87f7da6b28 ("net: phy: dp83867: move dt parsing to probe")
causes regression on TI dra71x-evm and dra72x-evm, where DP83867 PHY is
used in "rgmii-id" mode - the networking stops working.
Unfortunately, it's not enough to just move DT parsing code to .probe() as
it depends on phydev->interface value, which is set to correct value abter
the .probe() is completed and before calling .config_init(). So, RGMII
configuration can't be loaded from DT.

To fix and issue
- move RGMII validation code to .config_init()
- parse RGMII parameters in dp83867_of_init(), but consider them as
optional.

Fixes: ef87f7da6b28 ("net: phy: dp83867: move dt parsing to probe")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: ti: cpsw: fix extra rx interrupt

Now RX interrupt is triggered twice every time, because in
cpsw_rx_interrupt() it is asked first and then disabled. So there will be
pending interrupt always, when RX interrupt is enabled again in NAPI
handler.

Fix it by first disabling IRQ and then do ask.

Fixes: 870915feabdc ("drivers: net: cpsw: remove disable_irq/enable_irq as irq can be masked from cpsw itself")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

inet: protect against too small mtu values.

syzbot was once again able to crash a host by setting a very small mtu
on loopback device.

Let's make inetdev_valid_mtu() available in include/net/ip.h,
and use it in ip_setup_cork(), so that we protect both ip_append_page()
and __ip_append_data()

Also add a READ_ONCE() when the device mtu is read.

Pairs this lockless read with one WRITE_ONCE() in __dev_set_mtu(),
even if other code paths might write over this field.

Add a big comment in include/linux/netdevice.h about dev->mtu
needing READ_ONCE()/WRITE_ONCE() annotations.

Hopefully we will add the missing ones in followup patches.

[1]

refcount_t: saturated; leaking memory.
WARNING: CPU: 0 PID: 9464 at lib/refcount.c:22 refcount_warn_saturate+0x138/0x1f0 lib/refcount.c:22
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 9464 Comm: syz-executor850 Not tainted 5.4.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x197/0x210 lib/dump_stack.c:118
panic+0x2e3/0x75c kernel/panic.c:221
__warn.cold+0x2f/0x3e kernel/panic.c:582
report_bug+0x289/0x300 lib/bug.c:195
fixup_bug arch/x86/kernel/traps.c:174 [inline]
fixup_bug arch/x86/kernel/traps.c:169 [inline]
do_error_trap+0x11b/0x200 arch/x86/kernel/traps.c:267
do_invalid_op+0x37/0x50 arch/x86/kernel/traps.c:286
invalid_op+0x23/0x30 arch/x86/entry/entry_64.S:1027
RIP: 0010:refcount_warn_saturate+0x138/0x1f0 lib/refcount.c:22
Code: 06 31 ff 89 de e8 c8 f5 e6 fd 84 db 0f 85 6f ff ff ff e8 7b f4 e6 fd 48 c7 c7 e0 71 4f 88 c6 05 56 a6 a4 06 01 e8 c7 a8 b7 fd <0f> 0b e9 50 ff ff ff e8 5c f4 e6 fd 0f b6 1d 3d a6 a4 06 31 ff 89
RSP: 0018:ffff88809689f550 EFLAGS: 00010286
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff815e4336 RDI: ffffed1012d13e9c
RBP: ffff88809689f560 R08: ffff88809c50a3c0 R09: fffffbfff15d31b1
R10: fffffbfff15d31b0 R11: ffffffff8ae98d87 R12: 0000000000000001
R13: 0000000000040100 R14: ffff888099041104 R15: ffff888218d96e40
refcount_add include/linux/refcount.h:193 [inline]
skb_set_owner_w+0x2b6/0x410 net/core/sock.c:1999
sock_wmalloc+0xf1/0x120 net/core/sock.c:2096
ip_append_page+0x7ef/0x1190 net/ipv4/ip_output.c:1383
udp_sendpage+0x1c7/0x480 net/ipv4/udp.c:1276
inet_sendpage+0xdb/0x150 net/ipv4/af_inet.c:821
kernel_sendpage+0x92/0xf0 net/socket.c:3794
sock_sendpage+0x8b/0xc0 net/socket.c:936
pipe_to_sendpage+0x2da/0x3c0 fs/splice.c:458
splice_from_pipe_feed fs/splice.c:512 [inline]
__splice_from_pipe+0x3ee/0x7c0 fs/splice.c:636
splice_from_pipe+0x108/0x170 fs/splice.c:671
generic_splice_sendpage+0x3c/0x50 fs/splice.c:842
do_splice_from fs/splice.c:861 [inline]
direct_splice_actor+0x123/0x190 fs/splice.c:1035
splice_direct_to_actor+0x3b4/0xa30 fs/splice.c:990
do_splice_direct+0x1da/0x2a0 fs/splice.c:1078
do_sendfile+0x597/0xd00 fs/read_write.c:1464
__do_sys_sendfile64 fs/read_write.c:1525 [inline]
__se_sys_sendfile64 fs/read_write.c:1511 [inline]
__x64_sys_sendfile64+0x1dd/0x220 fs/read_write.c:1511
do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x441409
Code: e8 ac e8 ff ff 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 eb 08 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fffb64c4f78 EFLAGS: 00000246 ORIG_RAX: 0000000000000028
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 0000000000441409
RDX: 0000000000000000 RSI: 0000000000000006 RDI: 0000000000000005
RBP: 0000000000073b8a R08: 0000000000000010 R09: 0000000000000010
R10: 0000000000010001 R11: 0000000000000246 R12: 0000000000402180
R13: 0000000000402210 R14: 0000000000000000 R15: 0000000000000000
Kernel Offset: disabled
Rebooting in 86400 seconds..

Fixes: 1470ddf7f8ce ("inet: Remove explicit write references to sk/inet in ip_append_data")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gre: refetch erspan header from skb->data after pskb_may_pull()

After pskb_may_pull() we should always refetch the header
pointers from the skb->data in case it got reallocated.

In gre_parse_header(), the erspan header is still fetched
from the 'options' pointer which is fetched before
pskb_may_pull().

Found this during code review of a KMSAN bug report.

Fixes: cb73ee40b1b3 ("net: ip_gre: use erspan key field for tunnel lookup")
Cc: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: William Tu <u9012063@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pppoe: remove redundant BUG_ON() check in pppoe_pernet

Passing NULL to pppoe_pernet causes a crash via BUG_ON.
Dereferencing net in net_generici() also has the same effect. This patch
removes the redundant BUG_ON check on the same parameter.

Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

lib/: fix Kconfig indentation

Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ / /' -i */Kconfig

Link: http://lkml.kernel.org/r/20191120140140.19148-1-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel-hacking: move DEBUG_FS to 'Generic Kernel Debugging Instruments'

DEBUG_FS does not belong to 'Compile-time checks and compiler options'.

Link: http://lkml.kernel.org/r/20190909144453.3520-10-changbin.du@gmail.com
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel-hacking: move DEBUG_BUGVERBOSE to 'printk and dmesg options'

I think DEBUG_BUGVERBOSE is a dmesg option which gives more debug info
to dmesg.

Link: http://lkml.kernel.org/r/20190909144453.3520-9-changbin.du@gmail.com
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel-hacking: create a submenu for scheduler debugging options

Create a submenu 'Scheduler Debugging' for scheduler debugging options.

Link: http://lkml.kernel.org/r/20190909144453.3520-8-changbin.du@gmail.com
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel-hacking: move SCHED_STACK_END_CHECK after DEBUG_STACK_USAGE

They are both memory debug options to debug kernel stack issues.

Link: http://lkml.kernel.org/r/20190909144453.3520-7-changbin.du@gmail.com
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel-hacking: move Oops into 'Lockups and Hangs'

They are similar options so place them together.

Link: http://lkml.kernel.org/r/20190909144453.3520-6-changbin.du@gmail.com
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel-hacking: move kernel testing and coverage options to same submenu

Move error injection, coverage, testing options to a new top level
submenu 'Kernel Testing and Coverage'. They are all for test purpose.

Link: http://lkml.kernel.org/r/20190909144453.3520-5-changbin.du@gmail.com
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel-hacking: group kernel data structures debugging together

Group these similar runtime data structures verification options
together.

Link: http://lkml.kernel.org/r/20190909144453.3520-4-changbin.du@gmail.com
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel-hacking: create submenu for arch special debugging options

The arch special options are a little long, so create a submenu for
them.

Link: http://lkml.kernel.org/r/20190909144453.3520-3-changbin.du@gmail.com
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel-hacking: group sysrq/kgdb/ubsan into 'Generic Kernel Debugging Instruments'

Patch series "hacking: make 'kernel hacking' menu better structurized", v3.

This series is a trivial improvment for the layout of 'kernel hacking'
configuration menu. Now we have many items in it which makes takes a
little time to look up them since they are not well structurized yet.

Early discussion is here:
https://lkml.org/lkml/2019/9/1/39

This patch (of 9):

Group generic kernel debugging instruments sysrq/kgdb/ubsan together
into a new submenu.

Link: http://lkml.kernel.org/r/20190909144453.3520-2-changbin.du@gmail.com
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pipe: fix poll/select race introduced by the pipe rework

The kernel wait queues have a basic rule to them: you add yourself to
the wait-queue first, and then you check the things that you're going to
wait on. That avoids the races with the event you're waiting for.

The same goes for poll/select logic: the "poll_wait()" goes first, and
then you check the things you're polling for.

Of course, if you use locking, the ordering doesn't matter since the
lock will serialize with anything that changes the state you're looking
at. That's not the case here, though.

So move the poll_wait() first in pipe_poll(), before you start looking
at the pipe state.

Fixes: 8cefc107ca54 ("pipe: Use head and tail pointers for the ring, not cursor and length")
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

nfsd: depend on CRYPTO_MD5 for legacy client tracking

The legacy client tracking infrastructure of nfsd makes use of MD5 to
derive a client's recovery directory name. As the nfsd module doesn't
declare any dependency on CRYPTO_MD5, though, it may fail to allocate
the hash if the kernel was compiled without it. As a result, generation
of client recovery directories will fail with the following error:

NFSD: unable to generate recoverydir name

The explicit dependency on CRYPTO_MD5 was removed as redundant back in
6aaa67b5f3b9 (NFSD: Remove redundant "select" clauses in fs/Kconfig
2008-02-11) as it was already implicitly selected via RPCSEC_GSS_KRB5.
This broke when RPCSEC_GSS_KRB5 was made optional for NFSv4 in commit
df486a25900f (NFS: Fix the selection of security flavours in Kconfig) at
a later point.

Fix the issue by adding back an explicit dependency on CRYPTO_MD5.

Fixes: df486a25900f (NFS: Fix the selection of security flavours in Kconfig)
Signed-off-by: Patrick Steinhardt <ps@pks.im>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>

NFSD fixing possible null pointer derefering in copy offload

Static checker revealed possible error path leading to possible
NULL pointer dereferencing.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: e0639dc5805a: ("NFSD introduce async copy feature")
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>

Merge branch 'tcp-fix-handling-of-stale-syncookies-timestamps'

Guillaume Nault says:

====================
tcp: fix handling of stale syncookies timestamps

The synflood timestamps (->ts_recent_stamp and ->synq_overflow_ts) are
only refreshed when the syncookie protection triggers. Therefore, their
value can become very far apart from jiffies if no synflood happens for
a long time.

If jiffies grows too much and wraps while the synflood timestamp isn't
refreshed, then time_after32() might consider the later to be in the
future. This can trick tcp_synq_no_recent_overflow() into returning
erroneous values and rejecting valid ACKs.

Patch 1 handles the case of ACKs using legitimate syncookies.
Patch 2 handles the case of stray ACKs.
Patch 3 annotates lockless timestamp operations with READ_ONCE() and
WRITE_ONCE().

Changes from v3:
  - Fix description of time_between32() (found by Eric Dumazet).
  - Use more accurate Fixes tag in patch 3 (suggested by Eric Dumazet).

Changes from v2:
  - Define and use time_between32() instead of a pair of
    time_before32/time_after32 (suggested by Eric Dumazet).
  - Use 'last_overflow - HZ' as lower bound in
    tcp_synq_no_recent_overflow(), to accommodate for concurrent
    timestamp updates (found by Eric Dumazet).
  - Add a third patch to annotate lockless accesses to .ts_recent_stamp.

Changes from v1:
  - Initialising timestamps at socket creation time is not enough
    because jiffies wraps in 24 days with HZ=1000 (Eric Dumazet).
    Handle stale timestamps in tcp_synq_overflow() and
    tcp_synq_no_recent_overflow() instead.
  - Rework commit description.
  - Add a second patch to handle the case of stray ACKs.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE()

Syncookies borrow the ->rx_opt.ts_recent_stamp field to store the
timestamp of the last synflood. Protect them with READ_ONCE() and
WRITE_ONCE() since reads and writes aren't serialised.

Use of .rx_opt.ts_recent_stamp for storing the synflood timestamp was
introduced by a0f82f64e269 ("syncookies: remove last_synq_overflow from
struct tcp_sock"). But unprotected accesses were already there when
timestamp was stored in .last_synq_overflow.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: tighten acceptance of ACKs not matching a child socket

When no synflood occurs, the synflood timestamp isn't updated.
Therefore it can be so old that time_after32() can consider it to be
in the future.

That's a problem for tcp_synq_no_recent_overflow() as it may report
that a recent overflow occurred while, in fact, it's just that jiffies
has grown past 'last_overflow' + TCP_SYNCOOKIE_VALID + 2^31.

Spurious detection of recent overflows lead to extra syncookie
verification in cookie_v[46]_check(). At that point, the verification
should fail and the packet dropped. But we should have dropped the
packet earlier as we didn't even send a syncookie.

Let's refine tcp_synq_no_recent_overflow() to report a recent overflow
only if jiffies is within the
[last_overflow, last_overflow + TCP_SYNCOOKIE_VALID] interval. This
way, no spurious recent overflow is reported when jiffies wraps and
'last_overflow' becomes in the future from the point of view of
time_after32().

However, if jiffies wraps and enters the
[last_overflow, last_overflow + TCP_SYNCOOKIE_VALID] interval (with
'last_overflow' being a stale synflood timestamp), then
tcp_synq_no_recent_overflow() still erroneously reports an
overflow. In such cases, we have to rely on syncookie verification
to drop the packet. We unfortunately have no way to differentiate
between a fresh and a stale syncookie timestamp.

In practice, using last_overflow as lower bound is problematic.
If the synflood timestamp is concurrently updated between the time
we read jiffies and the moment we store the timestamp in
'last_overflow', then 'now' becomes smaller than 'last_overflow' and
tcp_synq_no_recent_overflow() returns true, potentially dropping a
valid syncookie.

Reading jiffies after loading the timestamp could fix the problem,
but that'd require a memory barrier. Let's just accommodate for
potential timestamp growth instead and extend the interval using
'last_overflow - HZ' as lower bound.

Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: fix rejected syncookies due to stale timestamps

If no synflood happens for a long enough period of time, then the
synflood timestamp isn't refreshed and jiffies can advance so much
that time_after32() can't accurately compare them any more.

Therefore, we can end up in a situation where time_after32(now,
last_overflow + HZ) returns false, just because these two values are
too far apart. In that case, the synflood timestamp isn't updated as
it should be, which can trick tcp_synq_no_recent_overflow() into
rejecting valid syncookies.

For example, let's consider the following scenario on a system
with HZ=1000:

  * The synflood timestamp is 0, either because that's the timestamp
    of the last synflood or, more commonly, because we're working with
    a freshly created socket.

  * We receive a new SYN, which triggers synflood protection. Let's say
    that this happens when jiffies == 2147484649 (that is,
    'synflood timestamp' + HZ + 2^31 + 1).

  * Then tcp_synq_overflow() doesn't update the synflood timestamp,
    because time_after32(2147484649, 1000) returns false.
    With:
      - 2147484649: the value of jiffies, aka. 'now'.
      - 1000: the value of 'last_overflow' + HZ.

  * A bit later, we receive the ACK completing the 3WHS. But
    cookie_v[46]_check() rejects it because tcp_synq_no_recent_overflow()
    says that we're not under synflood. That's because
    time_after32(2147484649, 120000) returns false.
    With:
      - 2147484649: the value of jiffies, aka. 'now'.
      - 120000: the value of 'last_overflow' + TCP_SYNCOOKIE_VALID.

    Of course, in reality jiffies would have increased a bit, but this
    condition will last for the next 119 seconds, which is far enough
    to accommodate for jiffie's growth.

Fix this by updating the overflow timestamp whenever jiffies isn't
within the [last_overflow, last_overflow + HZ] range. That shouldn't
have any performance impact since the update still happens at most once
per second.

Now we're guaranteed to have fresh timestamps while under synflood, so
tcp_synq_no_recent_overflow() can safely use it with time_after32() in
such situations.

Stale timestamps can still make tcp_synq_no_recent_overflow() return
the wrong verdict when not under synflood. This will be handled in the
next patch.

For 64 bits architectures, the problem was introduced with the
conversion of ->tw_ts_recent_stamp to 32 bits integer by commit
cca9bab1b72c ("tcp: use monotonic timestamps for PAWS").
The problem has always been there on 32 bits architectures.

Fixes: cca9bab1b72c ("tcp: use monotonic timestamps for PAWS")
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mlx5-fixes-2019-12-05' of git://git./linux/kernel/git/saeed/linux

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2019-12-05

This series introduces some fixes to mlx5 driver.

Please pull and let me know if there is any problem.

For -stable v4.19:
('net/mlx5e: Query global pause state before setting prio2buffer')

For -stable v5.3
('net/mlx5e: Fix SFF 8472 eeprom length')
('net/mlx5e: Fix translation of link mode into speed')
('net/mlx5e: Fix freeing flow with kfree() and not kvfree()')
('net/mlx5e: ethtool, Fix analysis of speed setting')
('net/mlx5e: Fix TXQ indices to be sequential')
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

lpc_eth: kernel BUG on remove

We may have found a bug in the nxp/lpc_eth.c driver. The function
platform_set_drvdata() is called twice, the second time it is called,
in lpc_mii_init(), it overwrites the struct net_device which should be
at pdev->dev->driver_data with pldat->mii_bus. When trying to remove
the driver, in lpc_eth_drv_remove(), platform_get_drvdata() will
return the pldat->mii_bus pointer and try to use it as a struct
net_device pointer. This causes unregister_netdev to segfault and
generate a kernel BUG. Is this reproducible?

Signed-off-by: Daniel Martinez <linux@danielsmartinez.com>
Signed-off-by: Bruno Carneiro da Cunha <brunocarneirodacunha@usp.br>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: md5: fix potential overestimation of TCP option space

Back in 2008, Adam Langley fixed the corner case of packets for flows
having all of the following options : MD5 TS SACK

Since MD5 needs 20 bytes, and TS needs 12 bytes, no sack block
can be cooked from the remaining 8 bytes.

tcp_established_options() correctly sets opts->num_sack_blocks
to zero, but returns 36 instead of 32.

This means TCP cooks packets with 4 extra bytes at the end
of options, containing unitialized bytes.

Fixes: 33ad798c924b ("tcp: options clean up")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-tc-indirect-block-relay'

John Hurley says:

====================
Ensure egress un/bind are relayed with indirect blocks

On register and unregister for indirect blocks, a command is called that
sends a bind/unbind event to the registering driver. This command assumes
that the bind to indirect block will be on ingress. However, drivers such
as NFP have allowed binding to clsact qdiscs as well as ingress qdiscs
from mainline Linux 5.2. A clsact qdisc binds to an ingress and an egress
block.

Rather than assuming that an indirect bind is always ingress, modify the
function names to remove the ingress tag (patch 1). In cls_api, which is
used by NFP to offload TC flower, generate bind/unbind message for both
ingress and egress blocks on the event of indirectly
registering/unregistering from that block. Doing so mimics the behaviour
of both ingress and clsact qdiscs on initialise and destroy.

This now ensures that drivers such as NFP receive the correct binder type
for the indirect block registration.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: sched: allow indirect blocks to bind to clsact in TC

When a device is bound to a clsact qdisc, bind events are triggered to
registered drivers for both ingress and egress. However, if a driver
registers to such a device using the indirect block routines then it is
assumed that it is only interested in ingress offload and so only replays
ingress bind/unbind messages.

The NFP driver supports the offload of some egress filters when
registering to a block with qdisc of type clsact. However, on unregister,
if the block is still active, it will not receive an unbind egress
notification which can prevent proper cleanup of other registered
callbacks.

Modify the indirect block callback command in TC to send messages of
ingress and/or egress bind depending on the qdisc in use. NFP currently
supports egress offload for TC flower offload so the changes are only
added to TC.

Fixes: 4d12ba42787b ("nfp: flower: allow offloading of matches on 'internal' ports")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: core: rename indirect block ingress cb function

With indirect blocks, a driver can register for callbacks from a device
that is does not 'own', for example, a tunnel device. When registering to
or unregistering from a new device, a callback is triggered to generate
a bind/unbind event. This, in turn, allows the driver to receive any
existing rules or to properly clean up installed rules.

When first added, it was assumed that all indirect block registrations
would be for ingress offloads. However, the NFP driver can, in some
instances, support clsact qdisc binds for egress offload.

Change the name of the indirect block callback command in flow_offload to
remove the 'ingress' identifier from it. While this does not change
functionality, a follow up patch will implement a more more generic
callback than just those currently just supporting ingress offload.

Fixes: 4d12ba42787b ("nfp: flower: allow offloading of matches on 'internal' ports")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net-sysfs: Call dev_hold always in netdev_queue_add_kobject

Dev_hold has to be called always in netdev_queue_add_kobject.
Otherwise usage count drops below 0 in case of failure in
kobject_init_and_add.

Fixes: b8eb718348b8 ("net-sysfs: Fix reference count leak in rx|netdev_queue_add_kobject")
Reported-by: Hulk Robot <hulkci@huawei.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: David Miller <davem@davemloft.net>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: fix flow dissection on Tx path

Commit 43e665287f93 ("net-next: dsa: fix flow dissection") added an
ability to override protocol and network offset during flow dissection
for DSA-enabled devices (i.e. controllers shipped as switch CPU ports)
in order to fix skb hashing for RPS on Rx path.

However, skb_hash() and added part of code can be invoked not only on
Rx, but also on Tx path if we have a multi-queued device and:
- kernel is running on UP system or
- XPS is not configured.

The call stack in this two cases will be like: dev_queue_xmit() ->
__dev_queue_xmit() -> netdev_core_pick_tx() -> netdev_pick_tx() ->
skb_tx_hash() -> skb_get_hash().

The problem is that skbs queued for Tx have both network offset and
correct protocol already set up even after inserting a CPU tag by DSA
tagger, so calling tag_ops->flow_dissect() on this path actually only
breaks flow dissection and hashing.

This can be observed by adding debug prints just before and right after
tag_ops->flow_dissect() call to the related block of code:

Before the patch:

Rx path (RPS):

[   19.240001] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[   19.244271] tag_ops->flow_dissect()
[   19.247811] Rx: proto: 0x0800, nhoff: 8 /* ETH_P_IP */

[   19.215435] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[   19.219746] tag_ops->flow_dissect()
[   19.223241] Rx: proto: 0x0806, nhoff: 8 /* ETH_P_ARP */

[   18.654057] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[   18.658332] tag_ops->flow_dissect()
[   18.661826] Rx: proto: 0x8100, nhoff: 8 /* ETH_P_8021Q */

Tx path (UP system):

[   18.759560] Tx: proto: 0x0800, nhoff: 26 /* ETH_P_IP */
[   18.763933] tag_ops->flow_dissect()
[   18.767485] Tx: proto: 0x920b, nhoff: 34 /* junk */

[   22.800020] Tx: proto: 0x0806, nhoff: 26 /* ETH_P_ARP */
[   22.804392] tag_ops->flow_dissect()
[   22.807921] Tx: proto: 0x920b, nhoff: 34 /* junk */

[   16.898342] Tx: proto: 0x86dd, nhoff: 26 /* ETH_P_IPV6 */
[   16.902705] tag_ops->flow_dissect()
[   16.906227] Tx: proto: 0x920b, nhoff: 34 /* junk */

After:

Rx path (RPS):

[   16.520993] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[   16.525260] tag_ops->flow_dissect()
[   16.528808] Rx: proto: 0x0800, nhoff: 8 /* ETH_P_IP */

[   15.484807] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[   15.490417] tag_ops->flow_dissect()
[   15.495223] Rx: proto: 0x0806, nhoff: 8 /* ETH_P_ARP */

[   17.134621] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */
[   17.138895] tag_ops->flow_dissect()
[   17.142388] Rx: proto: 0x8100, nhoff: 8 /* ETH_P_8021Q */

Tx path (UP system):

[   15.499558] Tx: proto: 0x0800, nhoff: 26 /* ETH_P_IP */

[   20.664689] Tx: proto: 0x0806, nhoff: 26 /* ETH_P_ARP */

[   18.565782] Tx: proto: 0x86dd, nhoff: 26 /* ETH_P_IPV6 */

In order to fix that we can add the check 'proto == htons(ETH_P_XDSA)'
to prevent code from calling tag_ops->flow_dissect() on Tx.
I also decided to initialize 'offset' variable so tagger callbacks can
now safely leave it untouched without provoking a chaos.

Fixes: 43e665287f93 ("net-next: dsa: fix flow dissection")
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/tls: Fix return values to avoid ENOTSUPP

ENOTSUPP is not available in userspace, for example:

setsockopt failed, 524, Unknown error 524

Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm

Pull ARM fixes from Russell King:

- fix CPU topology setup for SCHED_MC case

- fix VDSO regression

* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8947/1: Fix __arch_get_hw_counter() access to CNTVCT
ARM: 8943/1: Fix topology setup in case of CPU hotplug for CONFIG_SCHED_MC

Merge tag 'armsoc-fixes' of git://git./linux/kernel/git/soc/soc

Pull ARM SoC fixes from Olof Johansson:
"A set of fixes that we've merged late, but for the most part that have
  been sitting in -next for a while through platform maintainer trees:

   - Fixes to suspend/resume on Tegra, caused by the added features this
     merge window

   - Cleanups and minor fixes to TI additions this merge window

   - Tee fixes queued up late before the merge window, included here.

   - A handful of other fixlets

  There's also a refresh of the shareed config files (multi_v* on
  32-bit, and defconfig on 64-bit), to avoid conflicts when we get new
  contributions"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
  ARM: multi_v7_defconfig: Restore debugfs support
  ARM: defconfig: re-run savedefconfig on multi_v* configs
  arm64: defconfig: re-run savedefconfig
  ARM: pxa: Fix resource properties
  soc: mediatek: cmdq: fixup wrong input order of write api
  soc: aspeed: Fix snoop_file_poll()'s return type
  MAINTAINERS: Switch to Marvell addresses
  MAINTAINERS: update Cavium ThunderX drivers
  Revert "arm64: dts: juno: add dma-ranges property"
  MAINTAINERS: Make Nicolas Saenz Julienne the new bcm2835 maintainer
  firmware: arm_scmi: Avoid double free in error flow
  arm64: dts: juno: Fix UART frequency
  ARM: dts: Fix sgx sysconfig register for omap4
  arm: socfpga: execute cold reboot by default
  ARM: dts: Fix vcsi regulator to be always-on for droid4 to prevent hangs
  ARM: dts: dra7: fix cpsw mdio fck clock
  ARM: dts: am57xx-beagle-x15: Update pinmux name to ddr_3_3v
  ARM: dts: omap3-tao3530: Fix incorrect MMC card detection GPIO polarity
  soc/tegra: pmc: Add reset sources and levels on Tegra194
  soc/tegra: pmc: Add missing IRQ callbacks on Tegra194
  ...

Merge tag 'arm64-upstream' of git://git./linux/kernel/git/arm64/linux

Pull arm64 fixes from Catalin Marinas:

- ZONE_DMA32 initialisation fix when memblocks fall entirely within the
   first GB (used by ZONE_DMA in 5.5 for Raspberry Pi 4).

- Couple of ftrace fixes following the FTRACE_WITH_REGS patchset.

- access_ok() fix for the Tagged Address ABI when called from from a
   kernel thread (asynchronous I/O): the kthread does not have the TIF
   flags of the mm owner, so untag the user address unconditionally.

- KVM compute_layout() called before the alternatives code patching.

- Minor clean-ups.

* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: entry: refine comment of stack overflow check
  arm64: ftrace: fix ifdeffery
  arm64: KVM: Invoke compute_layout() before alternatives are applied
  arm64: Validate tagged addresses in access_ok() called from kernel threads
  arm64: mm: Fix column alignment for UXN in kernel_page_tables
  arm64: insn: consistently handle exit text
  arm64: mm: Fix initialisation of DMA zones on non-NUMA systems

pipe: Fix iteration end check in fuse_dev_splice_write()

Fix the iteration end check in fuse_dev_splice_write(). The iterator
position can only be compared with == or != since wrappage may be involved.

Fixes: 8cefc107ca54 ("pipe: Use head and tail pointers for the ring, not cursor and length")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'powerpc-5.5-2' of git://git./linux/kernel/git/powerpc/linux

Pull more powerpc updates from Michael Ellerman:
"A few commits splitting the KASAN instrumented bitops header in three,
  to match the split of the asm-generic bitops headers.

  This is needed on powerpc because we use the generic bitops for the
  non-atomic case only, whereas the existing KASAN instrumented bitops
  assume all the underlying operations are provided by the arch as
  arch_foo() versions.

  Thanks to: Daniel Axtens & Christophe Leroy"

* tag 'powerpc-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  docs/core-api: Remove possibly confusing sub-headings from Bit Operations
  powerpc: support KASAN instrumentation of bitops
  kasan: support instrumented bitops combined with generic bitops

Merge tag 'powerpc-5.5-3' of git://git./linux/kernel/git/powerpc/linux

Pull powerpc fixes from Michael Ellerman:
"One fix for a regression introduced by our recent rework of cache
  flushing on memory hotunplug.

  Like several other arches, our VDSO clock_getres() needed a fix to
  match the semantics of posix_get_hrtimer_res().

  A fix for a boot crash on Power9 LPARs using PCI LSI interrupts.

  A commit disabling use of the trace_imc PMU (not the core PMU) on
  Power9 systems, because it can lead to checkstops, until a workaround
  is developed.

  A handful of other minor fixes.

  Thanks to: Aneesh Kumar K.V, Anju T Sudhakar, Ard Biesheuvel,
  Christophe Leroy, Cédric Le Goater, Madhavan Srinivasan, Vincenzo
  Frascino"

* tag 'powerpc-5.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/perf: Disable trace_imc pmu
  powerpc/powernv: Avoid re-registration of imc debugfs directory
  powerpc/pmem: Convert to EXPORT_SYMBOL_GPL
  powerpc/archrandom: fix arch_get_random_seed_int()
  powerpc: Fix vDSO clock_getres()
  powerpc/pmem: Fix kernel crash due to wrong range value usage in flush_dcache_range
  powerpc/xive: Skip ioremap() of ESB pages for LSI interrupts
  powerpc/kasan: Fix boot failure with RELOCATABLE && FSL_BOOKE

Merge tag 'sound-fix-5.5-rc1' of git://git./linux/kernel/git/tiwai/sound

Pull more sound updates from Takashi Iwai:
"A few last-minute updates, most of them are the regression fixes:

   - AMD HD-audio HDMI runtime PM improvements

   - Fixes for HD-audio HDMI regressions wrt DP-MST

   - A regression fix for the previous aloop enhancement

   - A fix for a long-time problem in PCM OSS layer that was spotted by
     fuzzer now

   - A few HD-audio quirks"

* tag 'sound-fix-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: pcm: oss: Avoid potential buffer overflows
  ALSA: hda: hdmi - Keep old slot assignment behavior for Intel platforms
  ALSA: hda: Modify stream stripe mask only when needed
  ALSA: hda - fixup for the bass speaker on Lenovo Carbon X1 7th gen
  ALSA: hda: hdmi - preserve non-MST PCM routing for Intel platforms
  ALSA: hda: hdmi - fix kernel oops caused by invalid PCM idx
  ALSA: hda/realtek - Fix inverted bass GPIO pin on Acer 8951G
  ALSA: hda/realtek - Dell headphone has noise on unmute for ALC236
  ALSA: hda: hdmi - fix regression in connect list handling
  ALSA: aloop: Avoid pointer dereference before null-check
  ALSA: hda/hdmi - enable automatic runtime pm for AMD HDMI codecs by default
  ALSA: hda/hdmi - enable runtime pm for newer AMD display audio
  ALSA: hda/hdmi - Add new pci ids for AMD GPU display audio
  ALSA: hda/hdmi - fix vgaswitcheroo detection for AMD

pipe: fix incorrect caching of pipe state over pipe_wait()

Similarly to commit 8f868d68d335 ("pipe: Fix missing mask update after
pipe_wait()") this fixes a case where the pipe rewrite ended up caching
the pipe state incorrectly over a pipe lock drop event.

It wasn't quite as obvious, because you needed to splice data from a
pipe to a file, which is a fairly unusual operation, but it's completely
wrong.

Make sure we load the pipe head/tail/size information only after we've
waited for there to be data in the pipe.

While in that file, also make one of the splice helper functions use the
canonical arghument order for pipe_empty(). That's syntactic - pipe
emptiness is just that head and tail are equal, and thus mixing up head
and tail doesn't really matter. It's still wrong, though.

Reported-by: David Sterba <dsterba@suse.cz>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

smb3: fix mode passed in on create for modetosid mount option

When using the special SID to store the mode bits in an ACE (See
http://technet.microsoft.com/en-us/library/hh509017(v=ws.10).aspx)
which is enabled with mount parm "modefromsid" we were not
passing in the mode via SMB3 create (although chmod was enabled).
SMB3 create allows a security descriptor context to be passed
in (which is more atomic and thus preferable to setting the mode
bits after create via a setinfo).

This patch enables setting the mode bits on create when using
modefromsid mount option. In addition it fixes an endian
error in the definition of the Control field flags in the SMB3
security descriptor. It also makes the ACE type of the special
SID better match the documentation (and behavior of servers
which use this to store mode bits in SMB3 ACLs).

Signed-off-by: Steve French <stfrench@microsoft.com>
Acked-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>

net: avoid an indirect call in ____sys_recvmsg()

CONFIG_RETPOLINE=y made indirect calls expensive.

gcc seems to add an indirect call in ____sys_recvmsg().

Rewriting the code slightly makes sure to avoid this indirection.

Alternative would be to not call sock_recvmsg() and instead
use security_socket_recvmsg() and sock_recvmsg_nosec(),
but this is less readable IMO.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: David Laight <David.Laight@aculab.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

phy: mdio-thunder: add missed pci_release_regions in remove

The driver forgets to call pci_release_regions() in remove like that
in probe failure.
Add the missed call to fix it.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: fix ordering of tipc module init and exit routine

In order to set/get/dump, the tipc uses the generic netlink
infrastructure. So, when tipc module is inserted, init function
calls genl_register_family().
After genl_register_family(), set/get/dump commands are immediately
allowed and these callbacks internally use the net_generic.
net_generic is allocated by register_pernet_device() but this
is called after genl_register_family() in the __init function.
So, these callbacks would use un-initialized net_generic.

Test commands:
    #SHELL1
    while :
    do
        modprobe tipc
        modprobe -rv tipc
    done

    #SHELL2
    while :
    do
        tipc link list
    done

Splat looks like:
[   59.616322][ T2788] kasan: CONFIG_KASAN_INLINE enabled
[   59.617234][ T2788] kasan: GPF could be caused by NULL-ptr deref or user memory access
[   59.618398][ T2788] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[   59.619389][ T2788] CPU: 3 PID: 2788 Comm: tipc Not tainted 5.4.0+ #194
[   59.620231][ T2788] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[   59.621428][ T2788] RIP: 0010:tipc_bcast_get_broadcast_mode+0x131/0x310 [tipc]
[   59.622379][ T2788] Code: c7 c6 ef 8b 38 c0 65 ff 0d 84 83 c9 3f e8 d7 a5 f2 e3 48 8d bb 38 11 00 00 48 b8 00 00 00 00
[   59.622550][ T2780] NET: Registered protocol family 30
[   59.624627][ T2788] RSP: 0018:ffff88804b09f578 EFLAGS: 00010202
[   59.624630][ T2788] RAX: dffffc0000000000 RBX: 0000000000000011 RCX: 000000008bc66907
[   59.624631][ T2788] RDX: 0000000000000229 RSI: 000000004b3cf4cc RDI: 0000000000001149
[   59.624633][ T2788] RBP: ffff88804b09f588 R08: 0000000000000003 R09: fffffbfff4fb3df1
[   59.624635][ T2788] R10: fffffbfff50318f8 R11: ffff888066cadc18 R12: ffffffffa6cc2f40
[   59.624637][ T2788] R13: 1ffff11009613eba R14: ffff8880662e9328 R15: ffff8880662e9328
[   59.624639][ T2788] FS:  00007f57d8f7b740(0000) GS:ffff88806cc00000(0000) knlGS:0000000000000000
[   59.624645][ T2788] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   59.625875][ T2780] tipc: Started in single node mode
[   59.626128][ T2788] CR2: 00007f57d887a8c0 CR3: 000000004b140002 CR4: 00000000000606e0
[   59.633991][ T2788] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   59.635195][ T2788] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   59.636478][ T2788] Call Trace:
[   59.637025][ T2788]  tipc_nl_add_bc_link+0x179/0x1470 [tipc]
[   59.638219][ T2788]  ? lock_downgrade+0x6e0/0x6e0
[   59.638923][ T2788]  ? __tipc_nl_add_link+0xf90/0xf90 [tipc]
[   59.639533][ T2788]  ? tipc_nl_node_dump_link+0x318/0xa50 [tipc]
[   59.640160][ T2788]  ? mutex_lock_io_nested+0x1380/0x1380
[   59.640746][ T2788]  tipc_nl_node_dump_link+0x4fd/0xa50 [tipc]
[   59.641356][ T2788]  ? tipc_nl_node_reset_link_stats+0x340/0x340 [tipc]
[   59.642088][ T2788]  ? __skb_ext_del+0x270/0x270
[   59.642594][ T2788]  genl_lock_dumpit+0x85/0xb0
[   59.643050][ T2788]  netlink_dump+0x49c/0xed0
[   59.643529][ T2788]  ? __netlink_sendskb+0xc0/0xc0
[   59.644044][ T2788]  ? __netlink_dump_start+0x190/0x800
[   59.644617][ T2788]  ? __mutex_unlock_slowpath+0xd0/0x670
[   59.645177][ T2788]  __netlink_dump_start+0x5a0/0x800
[   59.645692][ T2788]  genl_rcv_msg+0xa75/0xe90
[   59.646144][ T2788]  ? __lock_acquire+0xdfe/0x3de0
[   59.646692][ T2788]  ? genl_family_rcv_msg_attrs_parse+0x320/0x320
[   59.647340][ T2788]  ? genl_lock_dumpit+0xb0/0xb0
[   59.647821][ T2788]  ? genl_unlock+0x20/0x20
[   59.648290][ T2788]  ? genl_parallel_done+0xe0/0xe0
[   59.648787][ T2788]  ? find_held_lock+0x39/0x1d0
[   59.649276][ T2788]  ? genl_rcv+0x15/0x40
[   59.649722][ T2788]  ? lock_contended+0xcd0/0xcd0
[   59.650296][ T2788]  netlink_rcv_skb+0x121/0x350
[   59.650828][ T2788]  ? genl_family_rcv_msg_attrs_parse+0x320/0x320
[   59.651491][ T2788]  ? netlink_ack+0x940/0x940
[   59.651953][ T2788]  ? lock_acquire+0x164/0x3b0
[   59.652449][ T2788]  genl_rcv+0x24/0x40
[   59.652841][ T2788]  netlink_unicast+0x421/0x600
[ ... ]

Fixes: 7e4369057806 ("tipc: fix a slab object leak")
Fixes: a62fbccecd62 ("tipc: make subscriber server support net namespace")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mqprio: Fix out-of-bounds access in mqprio_dump

When user runs a command like
tc qdisc add dev eth1 root mqprio
KASAN stack-out-of-bounds warning is emitted.
Currently, NLA_ALIGN macro used in mqprio_dump provides too large
buffer size as argument for nla_put and memcpy down the call stack.
The flow looks like this:
1. nla_put expects exact object size as an argument;
2. Later it provides this size to memcpy;
3. To calculate correct padding for SKB, nla_put applies NLA_ALIGN
macro itself.

Therefore, NLA_ALIGN should not be applied to the nla_put parameter.
Otherwise it will lead to out-of-bounds memory access in memcpy.

Fixes: 4e8b86c06269 ("mqprio: Introduce new hardware offload mode and shaper in mqprio")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: stmmac: reset Tx desc base address before restarting Tx

Refer to the databook of DesignWare Cores Ethernet MAC Universal:

6.2.1.5 Register 4 (Transmit Descriptor List Address Register

If this register is not changed when the ST bit is set to 0, then
the DMA takes the descriptor address where it was stopped earlier.

The stmmac_tx_err() does zero indices to Tx descriptors, but does
not reset HW current Tx descriptor address. To fix inconsistency,
the base address of the Tx descriptors should be rewritten before
restarting Tx.

Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

enetc: disable EEE autoneg by default

The EEE support has not been enabled on ENETC, but it may connect
to a PHY which supports EEE and advertises EEE by default, while
its link partner also advertises EEE. If this happens, the PHY enters
low power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
ENETC connects to, to prevent the above unwanted outcome.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>