net/mlx5e: Remove redundant match on tunnel destination mac

Remove hardcoded match on tunnel destination MAC address. Such match is no
longer required and would be wrong for stacked devices topology where
encapsulation destination MAC address will be the address of tunnel VF that
can change dynamically on route change (implemented in following patches in
the series).

Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5: E-Switch, Indirect table infrastructure

Indirect table infrastructure is used to allow fully processing VF tunnel
traffic in hardware. Kernel software model uses two TC rules for such
traffic: UL rep to tunnel device, then tunnel VF rep to destination VF rep.
To implement such pipeline driver needs to program the hardware after
matching on UL rule to overwrite source vport from UL to tunnel VF and
recirculate the packet to the root table to allow matching on the rule
installed on tunnel VF. For this indirect table matches all encapsulated
traffic by tunnel parameters and all other IP traffic is sent to tunnel VF
by the miss rule.

Indirect table API overview:

- mlx5_esw_indir_table_{init|destroy}() - init and destroy opaque indirect
table object.

- mlx5_esw_indir_table_get() - get or create new table according to vport
id and IP version. Table has following pre-created groups: recirculation
group with match on ethertype and VNI (rules that match encapsulated
packets are installed to this group) and forward group with default/miss
rule that forwards to vport of tunnel endpoint VF (rule for regular
non-encapsulated packets).

- mlx5_esw_indir_table_put() - decrease reference to the indirect table and
matching rule (for encapsulated traffic).

- mlx5_esw_indir_table_needed() - check that in_port is an uplink port and
out_port is VF on the same eswitch, verify that the rule is for IP traffic
and source port rewrite functionality can be used.

- mlx5_esw_indir_table_decap_vport() - function returns decap vport of
flow attribute.

Co-developed-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: Refactor tun routing helpers

Refactor tun routing helpers to use dedicated struct
mlx5e_tc_tun_route_attr instead of multiple output arguments. This
simplifies the callers (no need to keep track of bunch of output param
pointers) and allows to unify struct release code in new
mlx5e_tc_tun_route_attr_cleanup() helper instead of requiring callers to
manually release some of the output parameters that require it.

Simplify code by unifying error handling at the end of the function and
rearranging code. Remove redundant empty line.

Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: VF tunnel TX traffic offloading

When tunnel endpoint is on VF, driver still assumes that endpoint is on
uplink and incorrectly configures encap rule offload according to that
assumption. As a result, traffic is sent directly to the uplink and rules
installed on representor of tunnel endpoint VF are ignored.

Implement following changes to allow offloading tx traffic with tunnel
endpoint on VF:

- For tunneling flows perform route lookup on route and out devices pair.
If out device is uplink and route device is VF of same physical port, then
modify packet reg_c_0 metadata register (source port) with the value of VF
vport. Use eswitch vhca_id->vport mapping introduced in one of previous
patches in the series to obtain vport from route netdevice.

- Recirculate encapsulated packets to VF vport in order to apply any flow
rules installed on VF representor that match on encapsulated traffic.

Only enable support for this functionality when all following conditions
are true:

- Hardware advertises capability to preserve reg_c_0 value on packet
recirculation.

- Vport metadata matching is enabled.

- Termination tables are to be used by the flow.

Example TC rules for VF tunnel traffic:

1. Rule that redirects packets from UL to VF rep that has the tunnel
endpoint IP address:

$ tc -s filter show dev enp8s0f0 ingress
filter protocol ip pref 4 flower chain 0
filter protocol ip pref 4 flower chain 0 handle 0x1
  dst_mac 16:c9:a0:2d:69:2c
  src_mac 0c:42:a1:58:ab:e4
  eth_type ipv4
  ip_flags nofrag
  in_hw in_hw_count 1
        action order 1: mirred (Egress Redirect to device enp8s0f0_0) stolen
        index 3 ref 1 bind 1 installed 377 sec used 0 sec
        Action statistics:
        Sent 114096 bytes 952 pkt (dropped 0, overlimits 0 requeues 0)
        Sent software 0 bytes 0 pkt
        Sent hardware 114096 bytes 952 pkt
        backlog 0b 0p requeues 0
        cookie 878fa48d8c423fc08c3b6ca599b50a97
        no_percpu
        used_hw_stats delayed

2. Rule that decapsulates the tunneled flow and redirects to destination VF
representor:

$ tc -s filter show dev vxlan_sys_4789 ingress
filter protocol ip pref 4 flower chain 0
filter protocol ip pref 4 flower chain 0 handle 0x1
  dst_mac ca:2e:a7:3f:f5:0f
  src_mac 0a:40:bd:30:89:99
  eth_type ipv4
  enc_dst_ip 7.7.7.5
  enc_src_ip 7.7.7.1
  enc_key_id 98
  enc_dst_port 4789
  enc_tos 0
  ip_flags nofrag
  in_hw in_hw_count 1
        action order 1: tunnel_key  unset pipe
         index 2 ref 1 bind 1 installed 434 sec used 434 sec
        Action statistics:
        Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
        backlog 0b 0p requeues 0
        used_hw_stats delayed

        action order 2: mirred (Egress Redirect to device enp8s0f0_1) stolen
        index 4 ref 1 bind 1 installed 434 sec used 0 sec
        Action statistics:
        Sent 129936 bytes 1082 pkt (dropped 0, overlimits 0 requeues 0)
        Sent software 0 bytes 0 pkt
        Sent hardware 129936 bytes 1082 pkt
        backlog 0b 0p requeues 0
        cookie ac17cf398c4c69e4a5b2f7aabd1b88ff
        no_percpu
        used_hw_stats delayed

Co-developed-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5: E-Switch, Refactor rule offload forward action processing

Following patches in the series extend forwarding functionality with VF
tunnel TX and RX handling. Extract action forwarding processing code into
dedicated functions to simplify further extensions:

- Handle every forwarding case with dedicated function instead of inline
code.

- Extract forwarding dest dispatch conditional into helper function
esw_setup_dests().

- Unify forwaring cleanup code in error path of
mlx5_eswitch_add_offloaded_rule() and in rule deletion code of
__mlx5_eswitch_del_rule() in new helper function esw_cleanup_dests() (dual
to new esw_setup_dests() helper).

This patch does not change functionality.

Co-developed-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: Always set attr mdev pointer

Eswitch offloads extensions in following patches in the series require
attr->esw_attr->in_mdev pointer to always be set. This is already the case
for all code paths except mlx5_tc_ct_entry_add_rule() function. Fix the
function to assign mdev pointer with priv->mdev value.

Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5e: E-Switch, Maintain vhca_id to vport_num mapping

Following patches in the series need to be able to map VF netdev to vport.
Since it is trivial to obtain vhca_id from netdev, maintain mapping from
vhca_id to vport_num inside eswitch offloads using xarray. Provide function
mlx5_eswitch_vhca_id_to_vport() to be used by TC code in following patches
to obtain the mapping.

Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

net/mlx5: E-Switch, Refactor setting source port

Setting the source port requires only the E-Switch and vport number.
Refactor the function to get those parameters instead of passing the full
attribute.

Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Merge branch '1GbE' of git://git./linux/kernel/git/tnguy/next-queue

Tony Nguyen says:

====================
1GbE Intel Wired LAN Driver Updates 2021-02-03

This series contains updates to igc, igb, e1000e, and e1000 drivers.

Sasha adds counting of good transmit packets and reporting of NVM version
and gPHY version in ethtool firmware version. Replaces the use of strlcpy
to the preferred strscpy. Fixes a typo that caused the wrong register to be
output. He also removes an unused function pointer, some unneeded defines,
and a non-applicable comment. All changes for igc.

Gal Hammer fixes a typo which caused the RDBAL register values to be
shown instead of TDBAL for igb.

Nick Lowe enables RSS support for i211 devices for igb.

Tom Rix fixes checkpatch warning by removing h from printk format
specifier for igb.

Kaixu Xia removes setting of a variable that is overwritten before next
use for e1000e.

Sudip Mukherjee removes an unneeded assignment for e1000.

* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
  e1000: drop unneeded assignment in e1000_set_itr()
  e1000e: remove the redundant value assignment in e1000_update_nvm_checksum_spt
  igb: remove h from printk format specifier
  igb: Enable RSS for Intel I211 Ethernet Controller
  igb: fix TDBAL register show incorrect value
  igc: Fix TDBAL register show incorrect value
  igc: Remove unused FUNC_1 mask
  igc: Remove unused local receiver mask
  igc: Prefer strscpy over strlcpy
  igc: Expose the gPHY firmware version
  igc: Expose the NVM version
  igc: Add Host Good Packets Transmitted Count
  igc: Remove MULR mask define
  igc: Remove igc_set_fw_version comment
  igc: Clean up nvm_operations structure
====================

Link: https://lore.kernel.org/r/20210204004259.3662059-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'amend-hv_netvsc-copy-packets-sent-by-hyper-v-out-of-the-receive-buffer'

Andrea Parri says:

====================
Amend "hv_netvsc: Copy packets sent by Hyper-V out of the receive buffer"

Patch #2 also addresses the Smatch complaint reported here:

   https://lkml.kernel.org/r/YBp2oVIdMe+G%2FliJ@mwanda/
====================

Link: https://lore.kernel.org/r/20210203113513.558864-1-parri.andrea@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

hv_netvsc: Load and store the proper (NBL_HASH_INFO) per-packet info

Fix the typo.

Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Fixes: 0ba35fe91ce34f ("hv_netvsc: Copy packets sent by Hyper-V out of the receive buffer")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

hv_netvsc: Allocate the recv_buf buffers after NVSP_MSG1_TYPE_SEND_RECV_BUF

The recv_buf buffers are allocated in netvsc_device_add().  Later in
netvsc_init_buf() the response to NVSP_MSG1_TYPE_SEND_RECV_BUF allows
the host to set up a recv_section_size that could be bigger than the
(default) value used for that allocation.  The host-controlled value
could be used by a malicious host to bypass the check on the packet's
length in netvsc_receive() and hence to overflow the recv_buf buffer.

Move the allocation of the recv_buf buffers into netvsc_init_but().

Reported-by: Juan Vazquez <juvazq@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Fixes: 0ba35fe91ce34f ("hv_netvsc: Copy packets sent by Hyper-V out of the receive buffer")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'r8152-adjust-flow-for-power-cut'

Hayes Wang says:

====================
r8152: adjust flow for power cut

The two patches are used to adjust the flow about resuming from
the state of power cut. For the purpose, some functions have to
be updated first.
====================

Link: https://lore.kernel.org/r/1394712342-15778-398-Taiwan-albertk@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

r8152: adjust the flow of power cut for RTL8153B

For runtime resuming, the RTL8153B may be resumed from the state
of power cut, when enabling the feature of UPS. Then, the PHY
would be reset, so it is necessary to be initailized again.

Besides, the USB_U1U2_TIMER also has to be set again, so I move
it from r8153b_init() to r8153b_hw_phy_cfg().

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

r8152: replace several functions about phy patch request

Replace r8153_patch_request() with rtl_phy_patch_request().
Replace r8153_pre_ram_code() with rtl_pre_ram_code().
Replace r8153_post_ram_code() with rtl_post_ram_code().
Add rtl_patch_key_set().

The new functions have an additional parameter. It is used to wait
the patch request command finished. When the PHY is resumed from
the state of power cut, the PHY is at a safe mode and the
OCP_PHY_PATCH_STAT wouldn't be updated. For this situation, it is
safe to set patch request command without waiting OCP_PHY_PATCH_STAT.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: xrs700x: Correctly address device over I2C

On read, master should send 31 MSB of the register (only even values
are ever used), followed by a 1 to indicate read. Then, reading two
bytes, the device will output the register's value.

On write, master sends 31 MSB of the register, followed by a 0 to
indicate write, followed by two bytes containing the register value.

Flexibilis' documentation (version 1.3) specifies the opposite
polarity (#read/write), but the scope indicates that it is, in fact,
read/#write.

Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Link: https://lore.kernel.org/r/20210202191645.439-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: bcm_sf2: Check egress tagging of CFP rule with proper accessor

The flow steering struct ethtool_flow_ext::data field is __be32, so when
the CFP code needs to check the VLAN egress tagging attribute in bit 0,
it does this in CPU native endianness. So logically, the endianness
conversion is set up the other way around, although in practice the same
result is produced.

Gets rid of build warning:

warning: cast from restricted __be32
warning: incorrect type in argument 1 (different base types)
   expected unsigned int [usertype] val
   got restricted __be32
warning: cast from restricted __be32
warning: cast from restricted __be32
warning: cast from restricted __be32
warning: cast from restricted __be32
warning: restricted __be32 degrades to integer

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210203193918.2236994-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

drivers: net: ethernet: i825xx: Fix couple of spellings in the file ether1.c

s/initialsation/initialisation/
s/specifiing/specifying/

Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210204031648.27300-1-unixbhaskar@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'fix-w-1-compilation-warnings-in-net-folder'

Leon Romanovsky says:

====================
Fix W=1 compilation warnings in net/* folder

Changelog:
v2:
 * Patch 3: Added missing include file.
v1: https://lore.kernel.org/lkml/20210203101612.4004322-1-leon@kernel.org
 * Removed Fixes lines.
 * Changed target from net to be net-next.
 * Patch 1: Moved function declaration to be outside config instead
   games with if/endif.
 * Patch 3: Moved declarations to new header file.
v0: https://lore.kernel.org/lkml/20210202135544.3262383-1-leon@kernel.org
====================

Link: https://lore.kernel.org/r/20210203135112.4083711-1-leon@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

netfilter: move handlers to net/ip_vs.h

Fix the following compilation warnings:
net/netfilter/ipvs/ip_vs_proto_tcp.c:147:1: warning: no previous prototype for 'tcp_snat_handler' [-Wmissing-prototypes]
  147 | tcp_snat_handler(struct sk_buff *skb, struct ip_vs_protocol *pp,
      | ^~~~~~~~~~~~~~~~
net/netfilter/ipvs/ip_vs_proto_udp.c:136:1: warning: no previous prototype for 'udp_snat_handler' [-Wmissing-prototypes]
  136 | udp_snat_handler(struct sk_buff *skb, struct ip_vs_protocol *pp,
      | ^~~~~~~~~~~~~~~~

Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net/core: move gro function declarations to separate header

Fir the following compilation warnings:
 1031 | INDIRECT_CALLABLE_SCOPE void udp_v6_early_demux(struct sk_buff *skb)

net/ipv6/ip6_offload.c:182:41: warning: no previous prototype for ‘ipv6_gro_receive’ [-Wmissing-prototypes]
  182 | INDIRECT_CALLABLE_SCOPE struct sk_buff *ipv6_gro_receive(struct list_head *head,
      |                                         ^~~~~~~~~~~~~~~~
net/ipv6/ip6_offload.c:320:29: warning: no previous prototype for ‘ipv6_gro_complete’ [-Wmissing-prototypes]
  320 | INDIRECT_CALLABLE_SCOPE int ipv6_gro_complete(struct sk_buff *skb, int nhoff)
      |                             ^~~~~~~~~~~~~~~~~
net/ipv6/ip6_offload.c:182:41: warning: no previous prototype for ‘ipv6_gro_receive’ [-Wmissing-prototypes]
  182 | INDIRECT_CALLABLE_SCOPE struct sk_buff *ipv6_gro_receive(struct list_head *head,
      |                                         ^~~~~~~~~~~~~~~~
net/ipv6/ip6_offload.c:320:29: warning: no previous prototype for ‘ipv6_gro_complete’ [-Wmissing-prototypes]
  320 | INDIRECT_CALLABLE_SCOPE int ipv6_gro_complete(struct sk_buff *skb, int nhoff)

Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ipv6: move udp declarations to net/udp.h

Fix the following compilation warning:

net/ipv6/udp.c:1031:30: warning: no previous prototype for 'udp_v6_early_demux' [-Wmissing-prototypes]
 1031 | INDIRECT_CALLABLE_SCOPE void udp_v6_early_demux(struct sk_buff *skb)
      |                              ^~~~~~~~~~~~~~~~~~
net/ipv6/udp.c:1072:29: warning: no previous prototype for 'udpv6_rcv' [-Wmissing-prototypes]
 1072 | INDIRECT_CALLABLE_SCOPE int udpv6_rcv(struct sk_buff *skb)
      |                             ^~~~~~~~~

Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ipv6: silence compilation warning for non-IPV6 builds

The W=1 compilation of allmodconfig generates the following warning:

net/ipv6/icmp.c:448:6: warning: no previous prototype for 'icmp6_send' [-Wmissing-prototypes]
  448 | void icmp6_send(struct sk_buff *skb, u8 type, u8 code, __u32 info,
      |      ^~~~~~~~~~

Fix it by providing function declaration for builds with ipv6 as a module.

Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: remove redundant null check of an array

The null check of filp->f_path.dentry->d_iname is redundant because
it is an array of DNAME_INLINE_LEN chars and cannot be a null. Fix
this by removing the null check.

Addresses-Coverity: ("Array compared against 0")
Fixes: 04987ca1b9b6 ("net: hns3: add debugfs support for tm nodes, priority and qset info")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20210203131040.21656-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

nfc: pn533: Fix typo issue

change 'piority' to 'priority'
change 'succesfult' to 'successful'

Signed-off-by: wengjianfeng <wengjianfeng@yulong.com>
Link: https://lore.kernel.org/r/20210203093842.11180-1-samirweng1979@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'net-enable-udp-v6-sockets-receiving-v4-packets-with-udp'

Xin Long says:

====================
net: enable udp v6 sockets receiving v4 packets with UDP

Currently, udp v6 socket can not process v4 packets with UDP GRO, as
udp_encap_needed_key is not increased when udp_tunnel_encap_enable()
is called for v6 socket.

This patchset is to increase it and remove the unnecessary code in
bareudp in Patch 1/2, and improve rxrpc encap_enable by calling
udp_tunnel_encap_enable().
====================

Link: https://lore.kernel.org/r/cover.1612342376.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

rxrpc: call udp_tunnel_encap_enable in rxrpc_open_socket

When doing encap_enable/increasing encap_needed_key, up->encap_enabled
is not set in rxrpc_open_socket(), and it will cause encap_needed_key
not being decreased in udpv6_destroy_sock().

This patch is to improve it by just calling udp_tunnel_encap_enable()
where it increases both UDP and UDPv6 encap_needed_key and sets
up->encap_enabled.

v4->v5:
  - add the missing '#include <net/udp_tunnel.h>', as David Howells
    noticed.

Acked-and-tested-by: David Howells <dhowells@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

udp: call udp_encap_enable for v6 sockets when enabling encap

When enabling encap for a ipv6 socket without udp_encap_needed_key
increased, UDP GRO won't work for v4 mapped v6 address packets as
sk will be NULL in udp4_gro_receive().

This patch is to enable it by increasing udp_encap_needed_key for
v6 sockets in udp_tunnel_encap_enable(), and correspondingly
decrease udp_encap_needed_key in udpv6_destroy_sock().

v1->v2:
  - add udp_encap_disable() and export it.
v2->v3:
  - add the change for rxrpc and bareudp into one patch, as Alex
    suggested.
v3->v4:
  - move rxrpc part to another patch.

Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net-loopback: set lo dev initial state to UP

Traditionally loopback devices come up with initial state as DOWN for
any new network-namespace. This would mean that anyone needing this
device would have to bring this UP by issuing something like 'ip link
set lo up'. This can be avoided if the initial state is set as UP.

Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: Jian Yang <jianyang@google.com>
Link: https://lore.kernel.org/r/20210201233445.2044327-1-jianyang.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'net-consolidate-page_is_pfmemalloc-usage'

Alexander Lobakin says:

====================
net: consolidate page_is_pfmemalloc() usage

page_is_pfmemalloc() is used mostly by networking drivers to test
if a page can be considered for reusing/recycling.
It doesn't write anything to the struct page itself, so its sole
argument can be constified, as well as the first argument of
skb_propagate_pfmemalloc().
In Page Pool core code, it can be simply inlined instead.
Most of the callers from NIC drivers were just doppelgangers of
the same condition tests. Derive them into a new common function
do deduplicate the code.

Resend of v3 [2]:
 - it missed Patchwork and Netdev archives, probably due to server-side
   issues.

Since v2 [1]:
 - use more intuitive name for the new inline function since there's
   nothing "reserved" in remote pages (Jakub Kicinski, John Hubbard);
 - fold likely() inside the helper itself to make driver code a bit
   fancier (Jakub Kicinski);
 - split function introduction and using into two separate commits;
 - collect some more tags (Jesse Brandeburg, David Rientjes).

Since v1 [0]:
 - new: reduce code duplication by introducing a new common function
   to test if a page can be reused/recycled (David Rientjes);
 - collect autographs for Page Pool bits (Jesper Dangaard Brouer,
   Ilias Apalodimas).

[0] https://lore.kernel.org/netdev/20210125164612.243838-1-alobakin@pm.me
[1] https://lore.kernel.org/netdev/20210127201031.98544-1-alobakin@pm.me
[2] https://lore.kernel.org/lkml/20210131120844.7529-1-alobakin@pm.me
====================

Link: https://lore.kernel.org/r/20210202133030.5760-1-alobakin@pm.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: page_pool: simplify page recycling condition tests

pool_page_reusable() is a leftover from pre-NUMA-aware times. For now,
this function is just a redundant wrapper over page_is_pfmemalloc(),
so inline it into its sole call site.

Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: use the new dev_page_is_reusable() instead of private versions

Now we can remove a bunch of identical functions from the drivers and
make them use common dev_page_is_reusable(). All {,un}likely() checks
are omitted since it's already present in this helper.
Also update some comments near the call sites.

Suggested-by: David Rientjes <rientjes@google.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: introduce common dev_page_is_reusable()

A bunch of drivers test the page before reusing/recycling for two
common conditions:
 - if a page was allocated under memory pressure (pfmemalloc page);
 - if a page was allocated at a distant memory node (to exclude
   slowdowns).

Introduce a new common inline for doing this, with likely() already
folded inside to make driver code a bit simpler.

Suggested-by: David Rientjes <rientjes@google.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

skbuff: constify skb_propagate_pfmemalloc() "page" argument

The function doesn't write anything to the page struct itself,
so this argument can be const.

Misc: align second argument to the brace while at it.

Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mm: constify page_is_pfmemalloc() argument

The function only tests for page->index, so its argument should be
const.

Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: fix building errors on powerpc when CONFIG_RETPOLINE is not set

This commit fixes the errores reported when building for powerpc:

 ERROR: modpost: "ip6_dst_check" [vmlinux] is a static EXPORT_SYMBOL
 ERROR: modpost: "ipv4_dst_check" [vmlinux] is a static EXPORT_SYMBOL
 ERROR: modpost: "ipv4_mtu" [vmlinux] is a static EXPORT_SYMBOL
 ERROR: modpost: "ip6_mtu" [vmlinux] is a static EXPORT_SYMBOL

Fixes: f67fbeaebdc0 ("net: use indirect call helpers for dst_mtu")
Fixes: bbd807dfbf20 ("net: indirect call helpers for ipv4/ipv6 dst_check functions")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Link: https://lore.kernel.org/r/20210204181839.558951-2-brianvv@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: add EXPORT_INDIRECT_CALLABLE wrapper

When a static function is annotated with INDIRECT_CALLABLE_SCOPE and
CONFIG_RETPOLINE is set, the static keyword is removed. Sometimes the
function needs to be exported but EXPORT_SYMBOL can't be used because if
CONFIG_RETPOLINE is not set, we will attempt to export a static symbol.

This patch introduces a new indirect call wrapper:
EXPORT_INDIRECT_CALLABLE. This basically does EXPORT_SYMBOL when
CONFIG_RETPOLINE is set, but does nothing when it's not.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Link: https://lore.kernel.org/r/20210204181839.558951-1-brianvv@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

netlink: add tracepoint at NL_SET_ERR_MSG

Often userspace won't request the extack information, or they don't log it
because of log level or so, and even when they do, sometimes it's not
enough to know exactly what caused the error.

Netlink extack is the standard way of reporting erros with descriptive
error messages. With a trace point on it, we then can know exactly where
the error happened, regardless of userspace app. Also, we can even see if
the err msg was overwritten.

The wrapper do_trace_netlink_extack() is because trace points shouldn't be
called from .h files, as trace points are not that small, and the function
call to do_trace_netlink_extack() on the macros is not protected by
tracepoint_enabled() because the macros are called from modules, and this
would require exporting some trace structs. As this is error path, it's
better to export just the wrapper instead.

v2: removed leftover tracepoint declaration

Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/4546b63e67b2989789d146498b13cc09e1fdc543.1612403190.git.marcelo.leitner@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

drivers: net: xen-netfront: Simplify the calculation of variables

Fix the following coccicheck warnings:

./drivers/net/xen-netfront.c:1816:52-54: WARNING !A || A && B is
equivalent to !A || B.

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/1612261069-13315-1-git-send-email-jiapeng.chong@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'gtp'

Jonas Bonn says:

====================
There's ongoing work in this driver to provide support for IPv6, GRO,
GSO, and "collect metadata" mode operation.  In order to facilitate this
work going forward, this short series accumulates already ACK:ed patches
that are ready for the next merge window.

All of these patches should be uncontroversial at this point, including
the first one in the series that reverts a recently added change to
introduce "collect metadata" mode.  As that patch produces 'broken'
packets when common GTP headers are in place, it seems better to revert
it and rethink things a bit before inclusion.
====================

Link: https://lore.kernel.org/r/20210203070805.281321-1-jonas@norrbonn.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

gtp: update rx_length_errors for abnormally short packets

Based on work by Pravin Shelar.

Update appropriate stats when packet transmission isn't possible.

Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

gtp: set device type

Set the devtype to 'gtp' when setting up the link.

Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

gtp: drop unnecessary call to skb_dst_drop

The call to skb_dst_drop() is already done as part of udp_tunnel_xmit().

Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

gtp: really check namespaces before xmit

Blindly assuming that packet transmission crosses namespaces results in
skb marks being lost in the single namespace case.

Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

gtp: include role in link info

Querying link info for the GTP interface doesn't reveal in which "role" the
device is set to operate.  Include this information in the info query
result.

Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

gtp: set initial MTU

The GTP link is brought up with a default MTU of zero.  This can lead to
some rather unexpected behaviour for users who are more accustomed to
interfaces coming online with reasonable defaults.

This patch sets an initial MTU for the GTP link of 1500 less worst-case
tunnel overhead.

Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Revert "GTP: add support for flow based tunneling API"

This reverts commit 9ab7e76aefc97a9aa664accb59d6e8dc5e52514a.

This patch was committed without maintainer approval and despite a number
of unaddressed concerns from review.  There are several issues that
impede the acceptance of this patch and that make a reversion of this
particular instance of these changes the best way forward:

i)  the patch contains several logically separate changes that would be
better served as smaller patches (for review purposes)
ii) functionality like the handling of end markers has been introduced
without further explanation
iii) symmetry between the handling of GTPv0 and GTPv1 has been
unnecessarily broken
iv) the patchset produces 'broken' packets when extension headers are
included
v) there are no available userspace tools to allow for testing this
functionality
vi) there is an unaddressed Coverity report against the patch concering
memory leakage
vii) most importantly, the patch contains a large amount of superfluous
churn that impedes other ongoing work with this driver

This patch will be reworked into a series that aligns with other
ongoing work and facilitates review.

Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: tracepoint: exposing sk_family in all tcp:tracepoints

Similar to sock:inet_sock_set_state tracepoint, expose sk_family to
distinguish AF_INET and AF_INET6 families.

The following tcp tracepoints are updated:
tcp:tcp_destroy_sock
tcp:tcp_rcv_space_adjust
tcp:tcp_retransmit_skb
tcp:tcp_send_reset
tcp:tcp_receive_reset
tcp:tcp_retransmit_synack
tcp:tcp_probe

Signed-off-by: Hariharan Ananthakrishnan <hari@netflix.com>
Signed-off-by: Brendan Gregg <bgregg@netflix.com>
Link: https://lore.kernel.org/r/20210129001210.344438-1-hari@netflix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

tcp: use a smaller percpu_counter batch size for sk_alloc

Currently, a percpu_counter with the default batch size (2*nr_cpus) is
used to record the total # of active sockets per protocol. This means
sk_sockets_allocated_read_positive() could be off by +/-2*(nr_cpus^2).
This under/over-estimation could lead to wrong memory suppression
conditions in __sk_raise_mem_allocated().
Fix this by using a more reasonable fixed batch size of 16.

See related commit cf86a086a180 ("net/dst: use a smaller percpu_counter
batch for dst entries accounting") that addresses a similar issue.

Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Link: https://lore.kernel.org/r/20210202193408.1171634-1-weiwan@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'support-setting-lanes-via-ethtool'

Danielle Ratson says:

====================
Support setting lanes via ethtool

Some speeds can be achieved with different number of lanes. For example,
100Gbps can be achieved using two lanes of 50Gbps or four lanes of
25Gbps. This patchset adds a new selector that allows ethtool to
advertise link modes according to their number of lanes and also force a
specific number of lanes when autonegotiation is off.

Advertising all link modes with a speed of 100Gbps that use two lanes:

$ ethtool -s swp1 speed 100000 lanes 2 autoneg on

Forcing a speed of 100Gbps using four lanes:

$ ethtool -s swp1 speed 100000 lanes 4 autoneg off
====================

Link: https://lore.kernel.org/r/20210202180612.325099-1-danieller@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: selftests: Add lanes setting test

Test that setting lanes parameter is working.

Set max speed and max lanes in the list of advertised link modes,
and then try to set max speed with the lanes below max lanes if exists
in the list.

And then, test that setting number of lanes larger than max lanes fails.

Do the above for both autoneg on and off.

$ ./ethtool_lanes.sh

TEST: 4 lanes is autonegotiated                                     [ OK ]
TEST: Lanes number larger than max width is not set                 [ OK ]
TEST: Autoneg off, 4 lanes detected during force mode               [ OK ]
TEST: Lanes number larger than max width is not set                 [ OK ]

Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlxsw: ethtool: Pass link mode in use to ethtool

Currently, when user space queries the link's parameters, as speed and
duplex, each parameter is passed from the driver to ethtool.

Instead, pass the link mode bit in use.
In Spectrum-1, simply pass the bit that is set to '1' from PTYS register.
In Spectrum-2, pass the first link mode bit in the mask of the used
link mode.

Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlxsw: ethtool: Add support for setting lanes when autoneg is off

Currently, when auto negotiation is set to off, the user can force a
specific speed or both speed and duplex. The user cannot influence the
number of lanes that will be forced.

Add support for setting speed along with lanes so one would be able
to choose how many lanes will be forced.

When lanes parameter is passed from user space, choose the link mode
that its actual width equals to it.
Otherwise, the default link mode will be the one that supports the width
of the port.

Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlxsw: ethtool: Remove max lanes filtering

Currently, when a speed can be supported by different number of lanes,
the supported link modes bitmask contains only link modes with a single
number of lanes.

This was done in order to prevent auto negotiation on number of
lanes after 50G-1-lane and 100G-2-lanes link modes were introduced.

For example, if a port's max width is 4, only link modes with 4 lanes
will be presented as supported by that port, so 100G is always achieved by
4 lanes of 25G.

After the previous patches that allow selection of the number of lanes,
auto negotiation on number of lanes becomes practical.

Remove that filtering of the maximum number of lanes supported link modes,
so indeed all the supported and advertised link modes will be shown.

Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ethtool: Expose the number of lanes in use

Currently, ethtool does not expose how many lanes are used when the
link is up.

After adding a possibility to advertise or force a specific number of
lanes, the lanes in use value can be either the maximum width of the port
or below.

Extend ethtool to expose the number of lanes currently in use for
drivers that support it.

For example:

$ ethtool -s swp1 speed 100000 lanes 4
$ ethtool -s swp2 speed 100000 lanes 4
$ ip link set swp1 up
$ ip link set swp2 up
$ ethtool swp1
Settings for swp1:
        Supported ports: [ FIBRE         Backplane ]
        Supported link modes:   1000baseT/Full
                                10000baseT/Full
                                1000baseKX/Full
                                10000baseKR/Full
                                10000baseR_FEC
                                40000baseKR4/Full
                                40000baseCR4/Full
                                40000baseSR4/Full
                                40000baseLR4/Full
                                25000baseCR/Full
                                25000baseKR/Full
                                25000baseSR/Full
                                50000baseCR2/Full
                                50000baseKR2/Full
                                100000baseKR4/Full
                                100000baseSR4/Full
                                100000baseCR4/Full
                                100000baseLR4_ER4/Full
                                50000baseSR2/Full
                                10000baseCR/Full
                                10000baseSR/Full
                                10000baseLR/Full
                                10000baseER/Full
                                50000baseKR/Full
                                50000baseSR/Full
                                50000baseCR/Full
                                50000baseLR_ER_FR/Full
                                50000baseDR/Full
                                100000baseKR2/Full
                                100000baseSR2/Full
                                100000baseCR2/Full
                                100000baseLR2_ER2_FR2/Full
                                100000baseDR2/Full
                                200000baseKR4/Full
                                200000baseSR4/Full
                                200000baseLR4_ER4_FR4/Full
                                200000baseDR4/Full
                                200000baseCR4/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  1000baseT/Full
                                10000baseT/Full
                                1000baseKX/Full
                                1000baseKX/Full
                                10000baseKR/Full
                                10000baseR_FEC
                                40000baseKR4/Full
                                40000baseCR4/Full
                                40000baseSR4/Full
                                40000baseLR4/Full
                                25000baseCR/Full
                                25000baseKR/Full
                                25000baseSR/Full
                                50000baseCR2/Full
                                50000baseKR2/Full
                                100000baseKR4/Full
                                100000baseSR4/Full
                                100000baseCR4/Full
                                100000baseLR4_ER4/Full
                                50000baseSR2/Full
                                10000baseCR/Full
                                10000baseSR/Full
                                10000baseLR/Full
                                10000baseER/Full
                                200000baseKR4/Full
                                200000baseSR4/Full
                                200000baseLR4_ER4_FR4/Full
                                200000baseDR4/Full
                                200000baseCR4/Full
        Advertised pause frame use: No
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Advertised link modes:  100000baseKR4/Full
                                100000baseSR4/Full
                                100000baseCR4/Full
                                100000baseLR4_ER4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: 100000Mb/s
Lanes: 4
Duplex: Full
Auto-negotiation: on
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Link detected: yes

Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ethtool: Get link mode in use instead of speed and duplex parameters

Currently, when user space queries the link's parameters, as speed and
duplex, each parameter is passed from the driver to ethtool.

Instead, get the link mode bit in use, and derive each of the parameters
from it in ethtool.

Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ethtool: Extend link modes settings uAPI with lanes

Currently, when auto negotiation is on, the user can advertise all the
linkmodes which correspond to a specific speed, but does not have a
similar selector for the number of lanes. This is significant when a
specific speed can be achieved using different number of lanes.  For
example, 2x50 or 4x25.

Add 'ETHTOOL_A_LINKMODES_LANES' attribute and expand 'struct
ethtool_link_settings' with lanes field in order to implement a new
lanes-selector that will enable the user to advertise a specific number
of lanes as well.

When auto negotiation is off, lanes parameter can be forced only if the
driver supports it. Add a capability bit in 'struct ethtool_ops' that
allows ethtool know if the driver can handle the lanes parameter when
auto negotiation is off, so if it does not, an error message will be
returned when trying to set lanes.

Example:

$ ethtool -s swp1 lanes 4
$ ethtool swp1
  Settings for swp1:
Supported ports: [ FIBRE ]
        Supported link modes:   1000baseKX/Full
                                10000baseKR/Full
                                40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
                                25000baseCR/Full
                                25000baseSR/Full
50000baseCR2/Full
                                100000baseSR4/Full
100000baseCR4/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
                                100000baseSR4/Full
100000baseCR4/Full
        Advertised pause frame use: No
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Speed: Unknown!
        Duplex: Unknown! (255)
        Auto-negotiation: on
        Port: Direct Attach Copper
        PHYAD: 0
        Transceiver: internal
        Link detected: no

Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ethtool: Validate master slave configuration before rtnl_lock()

Create a new function for input validations to be called before
rtnl_lock() and move the master slave validation to that function.

This would be a cleanup for next patch that would add another validation
to the new function.

Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: fix SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING getting ignored

The bridge emits VLAN filtering events and quite a few others via
switchdev with orig_dev = br->dev. After the blamed commit, these events
started getting ignored.

The point of the patch was to not offload switchdev objects for ports
that didn't go through dsa_port_bridge_join, because the configuration
is unsupported:
- ports that offload a bonding/team interface go through
  dsa_port_bridge_join when that bonding/team interface is later bridged
  with another switch port or LAG
- ports that don't offload LAG don't get notified of the bridge that is
  on top of that LAG.

Sadly, a check is missing, which is that the orig_dev is equal to the
bridge device. This check is compatible with the original intention,
because ports that don't offload bridging because they use a software
LAG don't have dp->bridge_dev set.

On a semi-related note, we should not offload switchdev objects or
populate dp->bridge_dev if the driver doesn't implement .port_bridge_join
either. However there is no regression associated with that, so it can
be done separately.

Fixes: 5696c8aedfcc ("net: dsa: Don't offload port attributes on standalone ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Tobias Waldekranz <tobias@waldekranz.com>
Link: https://lore.kernel.org/r/20210202233109.1591466-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'chelsio-cxgb-use-threaded-interrupts-for-deferred-work'

Sebastian Andrzej Siewior says:

====================
chelsio: cxgb: Use threaded interrupts for deferred work

Patch #2 fixes an issue in which del_timer_sync() and tasklet_kill() is
invoked from the interrupt handler. This is probably a rare error case
since it disables interrupts / the card in that case.
Patch #1 converts a worker to use a threaded interrupt which is then
also used in patch #2 instead adding another worker for this task (and
flush_work() to synchronise vs rmmod).
====================

Link: https://lore.kernel.org/r/20210202170104.1909200-1-bigeasy@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

chelsio: cxgb: Disable the card on error in threaded interrupt

t1_fatal_err() is invoked from the interrupt handler. The bad part is
that it invokes (via t1_sge_stop()) del_timer_sync() and tasklet_kill().
Both functions must not be called from an interrupt because it is
possible that it will wait for the completion of the timer/tasklet it
just interrupted.

In case of a fatal error, use t1_interrupts_disable() to disable all
interrupt sources and then wake the interrupt thread with
F_PL_INTR_SGE_ERR as pending flag. The threaded-interrupt will stop the
card via t1_sge_stop() and not re-enable the interrupts again.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

chelsio: cxgb: Replace the workqueue with threaded interrupt

The external interrupt (F_PL_INTR_EXT) needs to be handled in a process
context and this is accomplished by utilizing a workqueue.

The process context can also be provided by a threaded interrupt instead
of a workqueue. The threaded interrupt can be used later for other
interrupt related processing which require non-atomic context without
using yet another workqueue. free_irq() also ensures that the thread is
done which is currently missing (the worker could continue after the
module has been removed).

Save pending flags in pending_thread_intr. Use the same mechanism
to disable F_PL_INTR_EXT as interrupt source like it is used before the
worker is scheduled. Enable the interrupt again once
t1_elmer0_ext_intr_handler() is done.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'support-for-octeontx2-98xx-cpt-block'

Srujana Challa says:

====================
Support for OcteonTX2 98xx CPT block.

OcteonTX2 series of silicons have multiple variants, the
98xx variant has two crypto (CPT) blocks to double the crypto
performance. This patchset adds support for new CPT block(CPT1).
====================

Link: https://lore.kernel.org/r/20210202152709.20450-1-schalla@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

octeontx2-af: Handle CPT function level reset

When FLR is initiated for a VF (PCI function level reset),
the parent PF gets a interrupt. PF then sends a message to
admin function (AF), which then cleans up all resources
attached to that VF. This patch adds support to handle
CPT FLR.

Signed-off-by: Narayana Prasad Raju Atherya <pathreya@marvell.com>
Signed-off-by: Suheil Chandran <schandran@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

octeontx2-af: Add support for CPT1 in debugfs

Adds support to display block CPT1 stats at
"/sys/kernel/debug/octeontx2/cpt1".

Signed-off-by: Mahipal Challa <mchalla@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

octeontx2-af: Mailbox changes for 98xx CPT block

This patch changes CPT mailbox message format to
support new block CPT1 in 98xx silicon.

cpt_rd_wr_reg ->
    Modify cpt_rd_wr_reg mailbox and its handler to
    accommodate new block CPT1.
cpt_lf_alloc ->
    Modify cpt_lf_alloc mailbox and its handler to
    configure LFs from a block address out of multiple
    blocks of same type. If a PF/VF needs to configure
    LFs from both the blocks then this mbox should be
    called twice.

Signed-off-by: Mahipal Challa <mchalla@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: mdiobus: Prevent spike on MDIO bus reset signal

The mdio_bus reset code first de-asserted the reset by allocating with
GPIOD_OUT_LOW, then asserted and de-asserted again. In other words, if
the reset signal defaulted to asserted, there'd be a short "spike"
before the reset.

Here is what happens depending on the pre-existing state of the reset
signal:
Reset (previously asserted):   ~~~|_|~~~~|_______
Reset (previously deasserted): _____|~~~~|_______
                                  ^ ^    ^
                                  A B    C

At point A, the low going transition is because the reset line is
requested using GPIOD_OUT_LOW. If the line is successfully requested,
the first thing we do is set it high _without_ any delay. This is
point B. So, a glitch occurs between A and B.

We then fsleep() and finally set the GPIO low at point C.

Requesting the line using GPIOD_OUT_HIGH eliminates the A and B
transitions. Instead we get:

Reset (previously asserted)  : ~~~~~~~~~~|______
Reset (previously deasserted): ____|~~~~~|______
                                   ^     ^
                                   A     C

Where A and C are the points described above in the code. Point B
has been eliminated.

The issue was found when we pulled down the reset signal for the
Marvell 88E1512P PHY (because it requires at least 50ms after POR with
an active clock). Looking at the reset signal with a scope revealed a
short spike, point B in the artwork above.

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210202143239.10714-1-mike.looijmans@topic.nl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

e1000: drop unneeded assignment in e1000_set_itr()

The variable 'current_itr' is assigned to 0 before jumping to
'set_itr_now' but it has not been used after the jump. So, remove the
unneeded assignment.

Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Reviewed-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

e1000e: remove the redundant value assignment in e1000_update_nvm_checksum_spt

Both of the statements are value assignment of the variable act_offset.
The first value assignment is overwritten by the second and is useless.
Remove it.

Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

igb: remove h from printk format specifier

This change fixes the checkpatch warning described in this
commit cbacb5ab0aa0 ("docs: printk-formats: Stop encouraging use of
unnecessary %h[xudi] and %hh[xudi]")

Standard integer promotion is already done and %hx and %hhx is useless
so do not encourage the use of %hh[xudi] or %h[xudi].

Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

igb: Enable RSS for Intel I211 Ethernet Controller

The Intel I211 Ethernet Controller supports 2 Receive Side Scaling (RSS)
queues. It should not be excluded from having this feature enabled.

Via commit c883de9fd787 ("igb: rename igb define to be more generic")
E1000_MRQC_ENABLE_RSS_4Q was renamed to E1000_MRQC_ENABLE_RSS_MQ to
indicate that this is a generic bit flag to enable queues and not
a flag that is specific to devices that support 4 queues

The bit flag enables 2, 4 or 8 queues appropriately depending on the part.

Tested with a multicore CPU and frames were then distributed as expected.

This issue appears to have been introduced because of confusion caused
by the prior name.

Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Tested-by: David Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

igb: fix TDBAL register show incorrect value

Fixed a typo which caused the registers dump function to read the
RDBAL register when printing TDBAL register values.

Signed-off-by: Gal Hammer <ghammer@redhat.com>
Tested-by: David Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

igc: Fix TDBAL register show incorrect value

Fixed a typo which caused the registers dump function to read the
RDBAL register when printing TDBAL register values.
_reg_dump method has been partially derived from i210 and have
same typo.

Suggested-by: Gal Hammer <ghammer@redhat.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

net: mscc: ocelot: fix error code in mscc_ocelot_probe()

Probe should return an error code if platform_get_irq_byname() fails
but it returns success instead.

Fixes: 6c30384eb1de ("net: mscc: ocelot: register devlink ports")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/YBkXyFIl4V9hgxYM@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: mscc: ocelot: fix error handling bugs in mscc_ocelot_init_ports()

There are several error handling bugs in mscc_ocelot_init_ports().  I
went through the code, and carefully audited it and made fixes and
cleanups.

1) The ocelot_probe_port() function didn't have a mirror release function
   so it was hard to follow.  I created the ocelot_release_port()
   function.
2) In the ocelot_probe_port() function, if the register_netdev() call
   failed, then it lead to a double free_netdev(dev) bug.  Fix this by
   setting "ocelot->ports[port] = NULL" on the error path.
3) I was concerned that the "port" which comes from of_property_read_u32()
   might be out of bounds so I added a check for that.
4) In the original code if ocelot_regmap_init() failed then the driver
   tried to continue but I think that should be a fatal error.
5) If ocelot_probe_port() failed then the most recent devlink was leaked.
   The fix for mostly came Vladimir Oltean.  Get rid of "registered_ports"
   and just set a bit in "devlink_ports_registered" to say when the
   devlink port has been registered (and needs to be unregistered on
   error).  There are fewer than 32 ports so a u32 is large enough for
   this purpose.
6) The error handling if the final ocelot_port_devlink_init() failed had
   two problems.  The "while (port-- >= 0)" loop should have been
   "--port" pre-op instead of a post-op to avoid a buffer underflow.
   The "if (!registered_ports[port])" condition was reversed leading to
   resource leaks and double frees.

Fixes: 6c30384eb1de ("net: mscc: ocelot: register devlink ports")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/YBkXhqRxHtRGzSnJ@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

igc: Remove unused FUNC_1 mask

FUNC_1 mask not in use in i225 device and could be removed

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

igc: Remove unused local receiver mask

Local receiver mask SR_1000T_LOCAL_RX_STATUS not in use in i225 device
and could be removed

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

igc: Prefer strscpy over strlcpy

Use the strscpy method instead of strlcpy method.

See: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr
_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

igc: Expose the gPHY firmware version

Extend reporting of NVM image version to include the gPHY (i225 PHY)
firmware version.

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

igc: Expose the NVM version

Expose the NVM map version via drvinfo in ethtool
NVM image version is reported as firmware version for i225 device
Minor typo fix - remove space

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

igc: Add Host Good Packets Transmitted Count

This counter counts the number of good (non-erred) packets
transmitted sent by the host.
A good transmit packet is considered one that is 64 or more bytes
in length (from <Destination Address> through <CRC>,
inclusively) in length

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

igc: Remove MULR mask define

Multiple Tx Data Read Requests is hardware pipeline feature and
is not controlled by software

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

igc: Remove igc_set_fw_version comment

i225 device not supported and do not plan to support
configuration of fw version string for ethtool

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

igc: Clean up nvm_operations structure

valid_led_default function pointer not in use and can
be removed from nvm_operations structure.

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Merge branch 'net-use-indirect_call-in-some-dst_ops'

Brian Vazquez says:

====================
net: use INDIRECT_CALL in some dst_ops

This patch series uses the INDIRECT_CALL wrappers in some dst_ops
functions to mitigate retpoline costs. Benefits depend on the
platform as described below.

Background: The kernel rewrites the retpoline code at
__x86_indirect_thunk_r11 depending on the CPU's requirements.
The INDIRECT_CALL wrappers provide hints on possible targets and
save the retpoline overhead using a direct call in case the
target matches one of the hints.

The retpoline overhead for the following three cases has been
measured by Luigi Rizzo in microbenchmarks, using CPU performance
counters, and cover reasonably well the range of possible retpoline
overheads compared to a plain indirect call (in equal conditions,
specifically with predicted branch, hot cache):

- just "jmp *(%r11)" on modern platforms like Intel Cascadelake.
  In this case the overhead is just 2 clock cycles:

- "lfence; jmp *(%r11)" on e.g. some recent AMD CPUs.
  In this case the lfence is blocked until pending reads complete,
  so the actual overhead depends on previous instructions.
  The best case we have measured 15 clock cycles of overhead.

- worst case, e.g. skylake, the full retpoline is used

    __x86_indirect_thunk_r11:     call set_u_target
    capture_speculation:          pause
                                  lfence
                                  jmp capture_speculation
    .align 16
    set_up_target:                mov %r11, (%rsp)
                                  ret

   In this case the overhead has been measured in 35-40 clock cycles.

The actual time saved hence depends on the platform and current
clock speed (which varies heavily, especially when C-states are active).
Also note that actual benefit might be lower than expected if the
longer retpoline overlaps with some pending memory read.

MEASUREMENTS:
The INDIRECT_CALL wrappers in this patchset involve the processing
of incoming SYN and generation of syncookies. Hence, the test has been
run by configuring a receiving host with a single NIC rx queue, disabling
RPS and RFS so that all processing occurs on the same core.
An external source generates SYN fast enough to saturate the receiving CPU.
We ran two sets of experiments, with and without the dst_output patch,
comparing the number of syncookies generated over a 20s period
in multiple runs.

Assuming the CPU is saturated, the time per packet is
   t = number_of_packets/total_time
and if the two datasets have statistically meaningful difference,
the difference in times between the two cases gives an estimate
of the benefits from one INDIRECT_CALL.

Here are the experimental results:

Skylake     Syncookies over 20s (5 tests)
---------------------------------------------------
indirect    9166325 9182023 9170093 9134014 9171082
retpoline   9099308 9126350 9154841 9056377 9122376

Computing the stats on the ns_pkt = 20e6/total_packets gives the following:

$ ministat -c 95 -w 70 /tmp/sk-indirect /tmp/sk-retp
x /tmp/sk-indirect
+ /tmp/sk-retp
+----------------------------------------------------------------------+
|x     xx x     +          x    + +           +                       +|
||______M__A_______|_|____________M_____A___________________|          |
+----------------------------------------------------------------------+
    N           Min           Max        Median           Avg        Stddev
x   5   2.17817e-06   2.18962e-06     2.181e-06  2.182292e-06 4.3252133e-09
+   5   2.18464e-06   2.20839e-06   2.19241e-06  2.194974e-06 8.8695958e-09
Difference at 95.0% confidence
        1.2682e-08 +/- 1.01766e-08
        0.581132% +/- 0.466326%
        (Student's t, pooled s = 6.97772e-09)

This suggests a difference of 13ns +/- 10ns
Our expectation from microbenchmarks was 35-40 cycles per call,
but part of the gains may be eaten by stalls from pending memory reads.

For Cascadelake:
Cascadelake     Syncookies over 20s (5 tests)
---------------------------------------------------------
indirect     10339797 10297547 10366826 10378891 10384854
retpoline    10332674 10366805 10320374 10334272 10374087

Computing the stats on the ns_pkt = 20e6/total_packets gives no
meaningful difference even at just 80% (this was expected):

$ ministat -c 80 -w 70 /tmp/cl-indirect /tmp/cl-retp
x /tmp/cl-indirect
+ /tmp/cl-retp
+----------------------------------------------------------------------+
|   x    x  +     *                   x   + +        +                x|
||______________|_M_________A_____A_______M________|___|               |
+----------------------------------------------------------------------+
    N           Min           Max        Median           Avg        Stddev
x   5   1.92588e-06   1.94221e-06   1.92923e-06  1.931716e-06 6.6936746e-09
+   5   1.92788e-06   1.93791e-06   1.93531e-06  1.933188e-06 4.3734106e-09
No difference proven at 80.0% confidence
====================

Link: https://lore.kernel.org/r/20210201174132.3534118-1-brianvv@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: indirect call helpers for ipv4/ipv6 dst_check functions

This patch avoids the indirect call for the common case:
ip6_dst_check and ipv4_dst_check

Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: use indirect call helpers for dst_mtu

This patch avoids the indirect call for the common case:
ip6_mtu and ipv4_mtu

Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: use indirect call helpers for dst_output

This patch avoids the indirect call for the common case:
ip6_output and ip_output

Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: use indirect call helpers for dst_input

This patch avoids the indirect call for the common case:
ip_local_deliver and ip6_input

Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: usb: cdc_ncm: use new API for bh tasklet

This converts the driver to use the new tasklet API introduced in
commit 12cc923f1ccc ("tasklet: Introduce new initialization API")

It is unfortunate that we need to add a pointer to the driver context to
get back to the usbnet device, but the space will be reclaimed once
there are no more users of the old API left and we can remove the data
value and flag from the tasklet struct.

Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210130234637.26505-1-kernel@esmil.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: fec: Silence M5272 build warnings

If CONFIG_M5272=y:

    drivers/net/ethernet/freescale/fec_main.c: In function ‘fec_restart’:
    drivers/net/ethernet/freescale/fec_main.c:948:6: warning: unused variable ‘val’ [-Wunused-variable]
      948 |  u32 val;
  |      ^~~
    drivers/net/ethernet/freescale/fec_main.c: In function ‘fec_get_mac’:
    drivers/net/ethernet/freescale/fec_main.c:1667:28: warning: unused variable ‘pdata’ [-Wunused-variable]
     1667 |  struct fec_platform_data *pdata = dev_get_platdata(&fep->pdev->dev);
  |                            ^~~~~

Fix this by moving the variable declarations inside the existing #ifdef
blocks.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210202130650.865023-1-geert@linux-m68k.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

inet: do not export inet_gro_{receive|complete}

inet_gro_receive() and inet_gro_complete() are part
of GRO engine which can not be modular.

Similarly, inet_gso_segment() does not need to be exported,
being part of GSO stack.

In other words, net/ipv6/ip6_offload.o is part of vmlinux,
regardless of CONFIG_IPV6.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20210202154145.1568451-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'mac80211-next-for-net-next-2021-02-02' of git://git./linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
This time, only RTNL locking reduction fallout.
 - cfg80211_dev_rename() requires RTNL
 - cfg80211_change_iface() and cfg80211_set_encryption()
   require wiphy mutex (was missing in wireless extensions)
 - cfg80211_destroy_ifaces() requires wiphy mutex
 - netdev registration can fail due to notifiers, and then
   notifiers are "unrolled", need to handle this properly

* tag 'mac80211-next-for-net-next-2021-02-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next:
  cfg80211: fix netdev registration deadlock
  cfg80211: call cfg80211_destroy_ifaces() with wiphy lock held
  wext: call cfg80211_set_encryption() with wiphy lock held
  wext: call cfg80211_change_iface() with wiphy lock held
  nl80211: call cfg80211_dev_rename() under RTNL
====================

Link: https://lore.kernel.org/r/20210202144106.38207-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'mlx5-updates-2021-02-01' of git://git./linux/kernel/git/saeed/linux

Saeed Mahameed says:

====================
mlx5-updates-2021-02-01

mlx5 netdev updates:

1) Trivial refactoring ahead of the upcoming uplink representor series.
2) Increased RSS table size to 256, for better results
3) Misc. Cleanup and very trivial improvements

* tag 'mlx5-updates-2021-02-01' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
  net/mlx5: DR, Avoid unnecessary csum recalculation on supporting devices
  net/mlx5e: CT: remove useless conversion to PTR_ERR then ERR_PTR
  net/mlx5e: accel, remove redundant space
  net/mlx5e: kTLS, Improve TLS RX workqueue scope
  net/mlx5e: remove h from printk format specifier
  net/mlx5e: Increase indirection RQ table size to 256
  net/mlx5e: Enable napi in channel's activation stage
  net/mlx5e: Move representor neigh init into profile enable
  net/mlx5e: Avoid false lock depenency warning on tc_ht
  net/mlx5e: Move set vxlan nic info to profile init
  net/mlx5e: Move netif_carrier_off() out of mlx5e_priv_init()
  net/mlx5e: Refactor mlx5e_netdev_init/cleanup to mlx5e_priv_init/cleanup
  net/mxl5e: Add change profile method
  net/mlx5e: Separate between netdev objects and mlx5e profiles initialization
====================

Link: https://lore.kernel.org/r/20210202065457.613312-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'mptcp-add_addr-enhancements'

Mat Martineau says:

====================
mptcp: ADD_ADDR enhancements

This patch series from the MPTCP tree contains enhancements and
associated tests for the ADD_ADDR ("add address") MPTCP option. This
option allows already-connected MPTCP peers to share additional IP
addresses with each other, which can then be used to create additional
subflows within those MPTCP connections.

Patches 1 & 2 remove duplicated data in the per-connection path manager
structure.

Patches 3-6 initiate additional subflows when an address is added using
the netlink path manager interface and improve ADD_ADDR signaling
reliability, subject to configured limits. Self tests are also updated.

Patches 7-15 add new support for optional port numbers in ADD_ADDR. This
includes creating an additional in-kernel TCP listening socket for the
requested port number, validating the port number when processing
incoming subflow connections, including the port number in netlink
interfaces, and adding some new MIBs. New self test cases are added for
subflows connecting with alternate port numbers.
====================

Link: https://lore.kernel.org/r/20210201230920.66027-1-mathew.j.martineau@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

selftests: mptcp: add testcases for ADD_ADDR with port

This patch adds testcases for ADD_ADDR with port and the related MIB
counters check in chk_add_nr. The output looks like this:

 24 signal address with port           syn[ ok ] - synack[ ok ] - ack[ ok ]
                                       add[ ok ] - echo  [ ok ] - pt [ ok ]
                                       syn[ ok ] - synack[ ok ] - ack[ ok ]
                                       syn[ ok ] - ack   [ ok ]
 25 subflow and signal with port       syn[ ok ] - synack[ ok ] - ack[ ok ]
                                       add[ ok ] - echo  [ ok ] - pt [ ok ]
                                       syn[ ok ] - synack[ ok ] - ack[ ok ]
                                       syn[ ok ] - ack   [ ok ]
 26 remove single address with port    syn[ ok ] - synack[ ok ] - ack[ ok ]
                                       add[ ok ] - echo  [ ok ] - pt [ ok ]
                                       syn[ ok ] - synack[ ok ] - ack[ ok ]
                                       syn[ ok ] - ack   [ ok ]
                                       rm [ ok ] - sf    [ ok ]

Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mptcp: add the mibs for ADD_ADDR with port

This patch adds the mibs for ADD_ADDR with port:

MPTCP_MIB_PORTADD for received ADD_ADDR suboption with a port number.

MPTCP_MIB_PORTSYNRX, MPTCP_MIB_PORTSYNACKRX, MPTCP_MIB_PORTACKRX, for
received MP_JOIN's SYN or SYN/ACK or ACK with a port number which is
different from the msk's port number.

MPTCP_MIB_MISMATCHPORTSYNRX and MPTCP_MIB_MISMATCHPORTACKRX, for
received SYN or ACK MP_JOIN with a mismatched port-number.

Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

selftests: mptcp: add port argument for pm_nl_ctl

This patch adds a new argument for pm_nl_ctl tool. We can use it like
this:

 # pm_nl_ctl add 10.0.2.1 flags signal port 10100
 # pm_nl_ctl dump
 id 1 flags signal 10.0.2.1 10100

Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mptcp: deal with MPTCP_PM_ADDR_ATTR_PORT in PM netlink

This patch adds MPTCP_PM_ADDR_ATTR_PORT filling and parsing in PM
netlink.

Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mptcp: enable use_port when invoke addresses_equal

When dealing with the addresses list local_addr_list or anno_list, we
should enable the function addresses_equal's parameter use_port. And
enable it in address_zero too.

Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>