gpio-f7188x: fix chip name and pin count on Nuvoton chip

[ Upstream commit 3002b8642f016d7fe3ff56240dacea1075f6b877 ]

In fact the device with chip id 0xD283 is called NCT6126D, and that is
the chip id the Nuvoton code was written for. Correct that name to avoid
confusion, because a NCT6116D in fact exists as well but has another
chip id, and is currently not supported.

The look at the spec also revealed that GPIO group7 in fact has 8 pins,
so correct the pin count in that group as well.

Fixes: d0918a84aff0 ("gpio-f7188x: Add GPIO support for Nuvoton NCT6116")
Reported-by: Xing Tong Wu <xingtong.wu@siemens.com>
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5: E-switch, Devcom, sync devcom events and devcom comp register

[ Upstream commit 8c253dfc89efde6b5faddf9e7400e5d17884e042 ]

devcom events are sent to all registered component. Following the
cited patch, it is possible for two components, e.g.: two eswitches,
to send devcom events, while both components are registered. This
means eswitch layer will do double un/pairing, which is double
allocation and free of resources, even though only one un/pairing is
needed. flow example:

cpu0 cpu1
---- ----

 mlx5_devlink_eswitch_mode_set(dev0)
  esw_offloads_devcom_init()
   mlx5_devcom_register_component(esw0)
                                         mlx5_devlink_eswitch_mode_set(dev1)
                                          esw_offloads_devcom_init()
                                           mlx5_devcom_register_component(esw1)
                                           mlx5_devcom_send_event()
   mlx5_devcom_send_event()

Hence, check whether the eswitches are already un/paired before
free/allocation of resources.

Fixes: 09b278462f16 ("net: devlink: enable parallel ops on netlink interface")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tls: rx: strp: preserve decryption status of skbs when needed

[ Upstream commit eca9bfafee3a0487e59c59201ae14c7594ba940a ]

When receive buffer is small we try to copy out the data from
TCP into a skb maintained by TLS to prevent connection from
stalling. Unfortunately if a single record is made up of a mix
of decrypted and non-decrypted skbs combining them into a single
skb leads to loss of decryption status, resulting in decryption
errors or data corruption.

Similarly when trying to use TCP receive queue directly we need
to make sure that all the skbs within the record have the same
status. If we don't the mixed status will be detected correctly
but we'll CoW the anchor, again collapsing it into a single paged
skb without decrypted status preserved. So the "fixup" code will
not know which parts of skb to re-encrypt.

Fixes: 84c61fe1a75b ("tls: rx: do not use the standard strparser")
Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tls: rx: strp: factor out copying skb data

[ Upstream commit c1c607b1e5d5477d82ca6a86a05a4f10907b33ee ]

We'll need to copy input skbs individually in the next patch.
Factor that code out (without assuming we're copying a full record).

Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: eca9bfafee3a ("tls: rx: strp: preserve decryption status of skbs when needed")
Signed-off-by: Sasha Levin <sashal@kernel.org>

tls: rx: strp: force mixed decrypted records into copy mode

[ Upstream commit 14c4be92ebb3e36e392aa9dd8f314038a9f96f3c ]

If a record is partially decrypted we'll have to CoW it, anyway,
so go into copy mode and allocate a writable skb right away.

This will make subsequent fix simpler because we won't have to
teach tls_strp_msg_make_copy() how to copy skbs while preserving
decrypt status.

Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: eca9bfafee3a ("tls: rx: strp: preserve decryption status of skbs when needed")
Signed-off-by: Sasha Levin <sashal@kernel.org>

tls: rx: strp: fix determining record length in copy mode

[ Upstream commit 8b0c0dc9fbbd01e58a573a41c38885f9e4c17696 ]

We call tls_rx_msg_size(skb) before doing skb->len += chunk.
So the tls_rx_msg_size() code will see old skb->len, most
likely leading to an over-read.

Worst case we will over read an entire record, next iteration
will try to trim the skb but may end up turning frag len negative
or discarding the subsequent record (since we already told TCP
we've read it during previous read but now we'll trim it out of
the skb).

Fixes: 84c61fe1a75b ("tls: rx: do not use the standard strparser")
Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tls: rx: strp: set the skb->len of detached / CoW'ed skbs

[ Upstream commit 210620ae44a83f25220450bbfcc22e6fe986b25f ]

alloc_skb_with_frags() fills in page frag sizes but does not
set skb->len and skb->data_len. Set those correctly otherwise
device offload will most likely generate an empty skb and
hit the BUG() at the end of __skb_nsg().

Fixes: 84c61fe1a75b ("tls: rx: do not use the standard strparser")
Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tls: rx: device: fix checking decryption status

[ Upstream commit b3a03b540e3cf62a255213d084d76d71c02793d5 ]

skb->len covers the entire skb, including the frag_list.
In fact we're guaranteed that rxm->full_len <= skb->len,
so since the change under Fixes we were not checking decrypt
status of any skb but the first.

Note that the skb_pagelen() added here may feel a bit costly,
but it's removed by subsequent fixes, anyway.

Reported-by: Tariq Toukan <tariqt@nvidia.com>
Fixes: 86b259f6f888 ("tls: rx: device: bound the frag walk")
Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

platform/x86/amd/pmf: Fix CnQF and auto-mode after resume

[ Upstream commit b54147fa374dbeadcb01b1762db1a793e06e37de ]

After suspend/resume cycle there is an error message and auto-mode
or CnQF stops working.

[ 5741.447511] amd-pmf AMDI0100:00: SMU cmd failed. err: 0xff
[ 5741.447523] amd-pmf AMDI0100:00: AMD_PMF_REGISTER_RESPONSE:ff
[ 5741.447527] amd-pmf AMDI0100:00: AMD_PMF_REGISTER_ARGUMENT:7
[ 5741.447531] amd-pmf AMDI0100:00: AMD_PMF_REGISTER_MESSAGE:16
[ 5741.447540] amd-pmf AMDI0100:00: [AUTO_MODE] avg power: 0 mW mode: QUIET

This is because the DRAM address used for accessing metrics table
needs to be refreshed after a suspend resume cycle. Add a resume
callback to reset this again.

Fixes: 1a409b35c995 ("platform/x86/amd/pmf: Get performance metrics from PMFW")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230513011408.958-1-mario.limonciello@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests/bpf: Fix pkg-config call building sign-file

[ Upstream commit 5f5486b620cd43b16a1787ef92b9bc21bd72ef2e ]

When building sign-file, the call to get the CFLAGS for libcrypto is
missing white-space between `pkg-config` and `--cflags`:

  $(shell $(HOSTPKG_CONFIG)--cflags libcrypto 2> /dev/null)

Removing the redirection of stderr, we see:

  $ make -C tools/testing/selftests/bpf sign-file
  make: Entering directory '[...]/tools/testing/selftests/bpf'
  make: pkg-config--cflags: No such file or directory
    SIGN-FILE sign-file
  make: Leaving directory '[...]/tools/testing/selftests/bpf'

Add the missing space.

Fixes: fc97590668ae ("selftests/bpf: Add test for bpf_verify_pkcs7_signature() kfunc")
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Roberto Sassu <roberto.sassu@huawei.com>
Link: https://lore.kernel.org/bpf/20230426215032.415792-1-jeremy@azazel.net
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

firmware: arm_ffa: Fix usage of partition info get count flag

[ Upstream commit c6e045361a27ecd4fac6413164e0d091d80eee99 ]

Commit bb1be7498500 ("firmware: arm_ffa: Add v1.1 get_partition_info support")
adds support to discovery the UUIDs of the partitions or just fetch the
partition count using the PARTITION_INFO_GET_RETURN_COUNT_ONLY flag.

However the commit doesn't handle the fact that the older version doesn't
understand the flag and must be MBZ which results in firmware returning
invalid parameter error. That results in the failure of the driver probe
which is in correct.

Limit the usage of the PARTITION_INFO_GET_RETURN_COUNT_ONLY flag for the
versions above v1.0(i.e v1.1 and onwards) which fixes the issue.

Fixes: bb1be7498500 ("firmware: arm_ffa: Add v1.1 get_partition_info support")
Reported-by: Jens Wiklander <jens.wiklander@linaro.org>
Reported-by: Marc Bonnici <marc.bonnici@arm.com>
Tested-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Link: https://lore.kernel.org/r/20230419-ffa_fixes_6-4-v2-2-d9108e43a176@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ipv{4,6}/raw: fix output xfrm lookup wrt protocol

[ Upstream commit 3632679d9e4f879f49949bb5b050e0de553e4739 ]

With a raw socket bound to IPPROTO_RAW (ie with hdrincl enabled), the
protocol field of the flow structure, build by raw_sendmsg() /
rawv6_sendmsg()),  is set to IPPROTO_RAW. This breaks the ipsec policy
lookup when some policies are defined with a protocol in the selector.

For ipv6, the sin6_port field from 'struct sockaddr_in6' could be used to
specify the protocol. Just accept all values for IPPROTO_RAW socket.

For ipv4, the sin_port field of 'struct sockaddr_in' could not be used
without breaking backward compatibility (the value of this field was never
checked). Let's add a new kind of control message, so that the userland
could specify which protocol is used.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
CC: stable@vger.kernel.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20230522120820.1319391-1-nicolas.dichtel@6wind.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

inet: Add IP_LOCAL_PORT_RANGE socket option

[ Upstream commit 91d0b78c5177f3e42a4d8738af8ac19c3a90d002 ]

Users who want to share a single public IP address for outgoing connections
between several hosts traditionally reach for SNAT. However, SNAT requires
state keeping on the node(s) performing the NAT.

A stateless alternative exists, where a single IP address used for egress
can be shared between several hosts by partitioning the available ephemeral
port range. In such a setup:

1. Each host gets assigned a disjoint range of ephemeral ports.
2. Applications open connections from the host-assigned port range.
3. Return traffic gets routed to the host based on both, the destination IP
   and the destination port.

An application which wants to open an outgoing connection (connect) from a
given port range today can choose between two solutions:

1. Manually pick the source port by bind()'ing to it before connect()'ing
   the socket.

   This approach has a couple of downsides:

   a) Search for a free port has to be implemented in the user-space. If
      the chosen 4-tuple happens to be busy, the application needs to retry
      from a different local port number.

      Detecting if 4-tuple is busy can be either easy (TCP) or hard
      (UDP). In TCP case, the application simply has to check if connect()
      returned an error (EADDRNOTAVAIL). That is assuming that the local
      port sharing was enabled (REUSEADDR) by all the sockets.

        # Assume desired local port range is 60_000-60_511
        s = socket(AF_INET, SOCK_STREAM)
        s.setsockopt(SOL_SOCKET, SO_REUSEADDR, 1)
        s.bind(("192.0.2.1", 60_000))
        s.connect(("1.1.1.1", 53))
        # Fails only if 192.0.2.1:60000 -> 1.1.1.1:53 is busy
        # Application must retry with another local port

      In case of UDP, the network stack allows binding more than one socket
      to the same 4-tuple, when local port sharing is enabled
      (REUSEADDR). Hence detecting the conflict is much harder and involves
      querying sock_diag and toggling the REUSEADDR flag [1].

   b) For TCP, bind()-ing to a port within the ephemeral port range means
      that no connecting sockets, that is those which leave it to the
      network stack to find a free local port at connect() time, can use
      the this port.

      IOW, the bind hash bucket tb->fastreuse will be 0 or 1, and the port
      will be skipped during the free port search at connect() time.

2. Isolate the app in a dedicated netns and use the use the per-netns
   ip_local_port_range sysctl to adjust the ephemeral port range bounds.

   The per-netns setting affects all sockets, so this approach can be used
   only if:

   - there is just one egress IP address, or
   - the desired egress port range is the same for all egress IP addresses
     used by the application.

   For TCP, this approach avoids the downsides of (1). Free port search and
   4-tuple conflict detection is done by the network stack:

     system("sysctl -w net.ipv4.ip_local_port_range='60000 60511'")

     s = socket(AF_INET, SOCK_STREAM)
     s.setsockopt(SOL_IP, IP_BIND_ADDRESS_NO_PORT, 1)
     s.bind(("192.0.2.1", 0))
     s.connect(("1.1.1.1", 53))
     # Fails if all 4-tuples 192.0.2.1:60000-60511 -> 1.1.1.1:53 are busy

  For UDP this approach has limited applicability. Setting the
  IP_BIND_ADDRESS_NO_PORT socket option does not result in local source
  port being shared with other connected UDP sockets.

  Hence relying on the network stack to find a free source port, limits the
  number of outgoing UDP flows from a single IP address down to the number
  of available ephemeral ports.

To put it another way, partitioning the ephemeral port range between hosts
using the existing Linux networking API is cumbersome.

To address this use case, add a new socket option at the SOL_IP level,
named IP_LOCAL_PORT_RANGE. The new option can be used to clamp down the
ephemeral port range for each socket individually.

The option can be used only to narrow down the per-netns local port
range. If the per-socket range lies outside of the per-netns range, the
latter takes precedence.

UAPI-wise, the low and high range bounds are passed to the kernel as a pair
of u16 values in host byte order packed into a u32. This avoids pointer
passing.

  PORT_LO = 40_000
  PORT_HI = 40_511

  s = socket(AF_INET, SOCK_STREAM)
  v = struct.pack("I", PORT_HI << 16 | PORT_LO)
  s.setsockopt(SOL_IP, IP_LOCAL_PORT_RANGE, v)
  s.bind(("127.0.0.1", 0))
  s.getsockname()
  # Local address between ("127.0.0.1", 40_000) and ("127.0.0.1", 40_511),
  # if there is a free port. EADDRINUSE otherwise.

[1] https://github.com/cloudflare/cloudflare-blog/blob/232b432c1d57/2022-02-connectx/connectx.py#L116

Reviewed-by: Marek Majkowski <marek@cloudflare.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 3632679d9e4f ("ipv{4,6}/raw: fix output xfrm lookup wrt protocol")
Signed-off-by: Sasha Levin <sashal@kernel.org>

Linux 6.1.31

Link: https://lore.kernel.org/r/20230528190835.386670951@linuxfoundation.org
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Tested-by: Takeshi Ogasawara <takeshi.ogasawara@futuring-girl.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Markus Reichelt <lkt+2023@mareichelt.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Ron Economos <re@w6rz.net>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Chris Paterson (CIP) <chris.paterson2@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: phy: mscc: add VSC8502 to MODULE_DEVICE_TABLE

commit 57fb54ab9f6945e204740b696bd4cee61ee04e5e upstream.

The mscc driver implements support for VSC8502, so its ID should be in
the MODULE_DEVICE_TABLE for automatic loading.

Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Fixes: d3169863310d ("net: phy: mscc: add support for VSC8502")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

3c589_cs: Fix an error handling path in tc589_probe()

commit 640bf95b2c7c2981fb471acdafbd3e0458f8390d upstream.

Should tc589_config() fail, some resources need to be released as already
done in the remove function.

Fixes: 15b99ac17295 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/d8593ae867b24c79063646e36f9b18b0790107cb.1684575975.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/smc: Reset connection when trying to use SMCRv2 fails.

commit 35112271672ae98f45df7875244a4e33aa215e31 upstream.

We found a crash when using SMCRv2 with 2 Mellanox ConnectX-4. It
can be reproduced by:

- smc_run nginx
- smc_run wrk -t 32 -c 500 -d 30 http://<ip>:<port>

 BUG: kernel NULL pointer dereference, address: 0000000000000014
 #PF: supervisor read access in kernel mode
 #PF: error_code(0x0000) - not-present page
 PGD 8000000108713067 P4D 8000000108713067 PUD 151127067 PMD 0
 Oops: 0000 [#1] PREEMPT SMP PTI
 CPU: 4 PID: 2441 Comm: kworker/4:249 Kdump: loaded Tainted: G        W   E      6.4.0-rc1+ #42
 Workqueue: smc_hs_wq smc_listen_work [smc]
 RIP: 0010:smc_clc_send_confirm_accept+0x284/0x580 [smc]
 RSP: 0018:ffffb8294b2d7c78 EFLAGS: 00010a06
 RAX: ffff8f1873238880 RBX: ffffb8294b2d7dc8 RCX: 0000000000000000
 RDX: 00000000000000b4 RSI: 0000000000000001 RDI: 0000000000b40c00
 RBP: ffffb8294b2d7db8 R08: ffff8f1815c5860c R09: 0000000000000000
 R10: 0000000000000400 R11: 0000000000000000 R12: ffff8f1846f56180
 R13: ffff8f1815c5860c R14: 0000000000000001 R15: 0000000000000001
 FS:  0000000000000000(0000) GS:ffff8f1aefd00000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 0000000000000014 CR3: 00000001027a0001 CR4: 00000000003706e0
 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
 Call Trace:
  <TASK>
  ? mlx5_ib_map_mr_sg+0xa1/0xd0 [mlx5_ib]
  ? smcr_buf_map_link+0x24b/0x290 [smc]
  ? __smc_buf_create+0x4ee/0x9b0 [smc]
  smc_clc_send_accept+0x4c/0xb0 [smc]
  smc_listen_work+0x346/0x650 [smc]
  ? __schedule+0x279/0x820
  process_one_work+0x1e5/0x3f0
  worker_thread+0x4d/0x2f0
  ? __pfx_worker_thread+0x10/0x10
  kthread+0xe5/0x120
  ? __pfx_kthread+0x10/0x10
  ret_from_fork+0x2c/0x50
  </TASK>

During the CLC handshake, server sequentially tries available SMCRv2
and SMCRv1 devices in smc_listen_work().

If an SMCRv2 device is found. SMCv2 based link group and link will be
assigned to the connection. Then assumed that some buffer assignment
errors happen later in the CLC handshake, such as RMB registration
failure, server will give up SMCRv2 and try SMCRv1 device instead. But
the resources assigned to the connection won't be reset.

When server tries SMCRv1 device, the connection creation process will
be executed again. Since conn->lnk has been assigned when trying SMCRv2,
it will not be set to the correct SMCRv1 link in
smcr_lgr_conn_assign_link(). So in such situation, conn->lgr points to
correct SMCRv1 link group but conn->lnk points to the SMCRv2 link
mistakenly.

Then in smc_clc_send_confirm_accept(), conn->rmb_desc->mr[link->link_idx]
will be accessed. Since the link->link_idx is not correct, the related
MR may not have been initialized, so crash happens.

 | Try SMCRv2 device first
 |     |-> conn->lgr: assign existed SMCRv2 link group;
 |     |-> conn->link: assign existed SMCRv2 link (link_idx may be 1 in SMC_LGR_SYMMETRIC);
 |     |-> sndbuf & RMB creation fails, quit;
 |
 | Try SMCRv1 device then
 |     |-> conn->lgr: create SMCRv1 link group and assign;
 |     |-> conn->link: keep SMCRv2 link mistakenly;
 |     |-> sndbuf & RMB creation succeed, only RMB->mr[link_idx = 0]
 |         initialized.
 |
 | Then smc_clc_send_confirm_accept() accesses
 | conn->rmb_desc->mr[conn->link->link_idx, which is 1], then crash.
 v

This patch tries to fix this by cleaning conn->lnk before assigning
link. In addition, it is better to reset the connection and clean the
resources assigned if trying SMCRv2 failed in buffer creation or
registration.

Fixes: e49300a6bf62 ("net/smc: add listen processing for SMC-Rv2")
Link: https://lore.kernel.org/r/20220523055056.2078994-1-liuyacan@corp.netease.com/
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

regulator: mt6359: add read check for PMIC MT6359

commit a511637502b1caa135046d0f8fdabd55a31af8ef upstream.

Add hardware version read check for PMIC MT6359

Signed-off-by: Sen Chu <sen.chu@mediatek.com
Fixes: 4cfc96547512 ("regulator: mt6359: Add support for MT6359P regulator")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com
Link: https://lore.kernel.org/r/20230518040646.8730-1-sen.chu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

firmware: arm_ffa: Set reserved/MBZ fields to zero in the memory descriptors

commit 111a833dc5cbef3d05b2a796a7e23cb7f6ff2192 upstream.

The transmit buffers allocated by the driver can be used to transmit data
by any messages/commands needing the buffer. However, it is not guaranteed
to have been zero-ed before every new transmission and hence it will just
contain residual value from the previous transmission. There are several
reserved fields in the memory descriptors that must be zero(MBZ). The
receiver can reject the transmission if any such MBZ fields are non-zero.

While we can set the whole page to zero, it is not optimal as most of the
fields get initialised to the value required for the current transmission.

So, just set the reserved/MBZ fields to zero in the memory descriptors
explicitly to honour the requirement and keep the receiver happy.

Fixes: cc2195fe536c ("firmware: arm_ffa: Add support for MEM_* interfaces")
Reported-by: Marc Bonnici <marc.bonnici@arm.com>
Link: https://lore.kernel.org/r/20230503131252.12585-1-sudeep.holla@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: dts: imx8mn-var-som: fix PHY detection bug by adding deassert delay

commit f161cea5a20f3aeeb637a88ad1705fc2720b4d58 upstream.

While testing the ethernet interface on a Variscite symphony carrier
board using an imx8mn SOM with an onboard ADIN1300 PHY (EC hardware
configuration), the ethernet PHY is not detected.

The ADIN1300 datasheet indicate that the "Management interface
active (t4)" state is reached at most 5ms after the reset signal is
deasserted.

The device tree in Variscite custom git repository uses the following
property:

    phy-reset-post-delay = <20>;

Add a new MDIO property 'reset-deassert-us' of 20ms to have the same
delay inside the ethphy node. Adding this property fixes the problem
with the PHY detection.

Note that this SOM can also have an Atheros AR8033 PHY. In this case,
a 1ms deassert delay is sufficient. Add a comment to that effect.

Fixes: ade0176dd8a0 ("arm64: dts: imx8mn-var-som: Add Variscite VAR-SOM-MX8MN System on Module")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: Devcom, serialize devcom registration

commit 1f893f57a3bf9fe1f4bcb25b55aea7f7f9712fe7 upstream.

From one hand, mlx5 driver is allowing to probe PFs in parallel.
From the other hand, devcom, which is a share resource between PFs, is
registered without any lock. This might resulted in memory problems.

Hence, use the global mlx5_dev_list_lock in order to serialize devcom
registration.

Fixes: fadd59fc50d0 ("net/mlx5: Introduce inter-device communication mechanism")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: Devcom, fix error flow in mlx5_devcom_register_device

commit af87194352cad882d787d06fb7efa714acd95427 upstream.

In case devcom allocation is failed, mlx5 is always freeing the priv.
However, this priv might have been allocated by a different thread,
and freeing it might lead to use-after-free bugs.
Fix it by freeing the priv only in case it was allocated by the
running thread.

Fixes: fadd59fc50d0 ("net/mlx5: Introduce inter-device communication mechanism")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: Collect command failures data only for known commands

commit 2a0a935fb64ee8af253b9c6133bb6702fb152ac2 upstream.

DEVX can issue a general command, which is not used by mlx5 driver.
In case such command is failed, mlx5 is trying to collect the failure
data, However, mlx5 doesn't create a storage for this command, since
mlx5 doesn't use it. This lead to array-index-out-of-bounds error.

Fix it by checking whether the command is known before collecting the
failure data.

Fixes: 34f46ae0d4b3 ("net/mlx5: Add command failures data to debugfs")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: Fix error message when failing to allocate device memory

commit a65735148e0328f80c0f72f9f8d2f609bfcf4aff upstream.

Fix spacing for the error and also the correct error code pointer.

Fixes: c9b9dcb430b3 ("net/mlx5: Move device memory management to mlx5_core")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: DR, Check force-loopback RC QP capability independently from RoCE

commit c7dd225bc224726c22db08e680bf787f60ebdee3 upstream.

SW Steering uses RC QP for writing STEs to ICM. This writingis done in LB
(loopback), and FL (force-loopback) QP is preferred for performance. FL is
available when RoCE is enabled or disabled based on RoCE caps.
This patch adds reading of FL capability from HCA caps in addition to the
existing reading from RoCE caps, thus fixing the case where we didn't
have loopback enabled when RoCE was disabled.

Fixes: 7304d603a57a ("net/mlx5: DR, Add support for force-loopback QP")
Signed-off-by: Itamar Gozlan <igozlan@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: Handle pairing of E-switch via uplink un/load APIs

commit 2be5bd42a5bba1a05daedc86cf0e248210009669 upstream.

In case user switch a device from switchdev mode to legacy mode, mlx5
first unpair the E-switch and afterwards unload the uplink vport.
From the other hand, in case user remove or reload a device, mlx5
first unload the uplink vport and afterwards unpair the E-switch.

The latter is causing a bug[1], hence, handle pairing of E-switch as
part of uplink un/load APIs.

[1]
In case VF_LAG is used, every tc fdb flow is duplicated to the peer
esw. However, the original esw keeps a pointer to this duplicated
flow, not the peer esw.
e.g.: if user create tc fdb flow over esw0, the flow is duplicated
over esw1, in FW/HW, but in SW, esw0 keeps a pointer to the duplicated
flow.
During module unload while a peer tc fdb flow is still offloaded, in
case the first device to be removed is the peer device (esw1 in the
example above), the peer net-dev is destroyed, and so the mlx5e_priv
is memset to 0.
Afterwards, the peer device is trying to unpair himself from the
original device (esw0 in the example above). Unpair API invoke the
original device to clear peer flow from its eswitch (esw0), but the
peer flow, which is stored over the original eswitch (esw0), is
trying to use the peer mlx5e_priv, which is memset to 0 and result in
bellow kernel-oops.

[  157.964081 ] BUG: unable to handle page fault for address: 000000000002ce60
[  157.964662 ] #PF: supervisor read access in kernel mode
[  157.965123 ] #PF: error_code(0x0000) - not-present page
[  157.965582 ] PGD 0 P4D 0
[  157.965866 ] Oops: 0000 [#1] SMP
[  157.967670 ] RIP: 0010:mlx5e_tc_del_fdb_flow+0x48/0x460 [mlx5_core]
[  157.976164 ] Call Trace:
[  157.976437 ]  <TASK>
[  157.976690 ]  __mlx5e_tc_del_fdb_peer_flow+0xe6/0x100 [mlx5_core]
[  157.977230 ]  mlx5e_tc_clean_fdb_peer_flows+0x67/0x90 [mlx5_core]
[  157.977767 ]  mlx5_esw_offloads_unpair+0x2d/0x1e0 [mlx5_core]
[  157.984653 ]  mlx5_esw_offloads_devcom_event+0xbf/0x130 [mlx5_core]
[  157.985212 ]  mlx5_devcom_send_event+0xa3/0xb0 [mlx5_core]
[  157.985714 ]  esw_offloads_disable+0x5a/0x110 [mlx5_core]
[  157.986209 ]  mlx5_eswitch_disable_locked+0x152/0x170 [mlx5_core]
[  157.986757 ]  mlx5_eswitch_disable+0x51/0x80 [mlx5_core]
[  157.987248 ]  mlx5_unload+0x2a/0xb0 [mlx5_core]
[  157.987678 ]  mlx5_uninit_one+0x5f/0xd0 [mlx5_core]
[  157.988127 ]  remove_one+0x64/0xe0 [mlx5_core]
[  157.988549 ]  pci_device_remove+0x31/0xa0
[  157.988933 ]  device_release_driver_internal+0x18f/0x1f0
[  157.989402 ]  driver_detach+0x3f/0x80
[  157.989754 ]  bus_remove_driver+0x70/0xf0
[  157.990129 ]  pci_unregister_driver+0x34/0x90
[  157.990537 ]  mlx5_cleanup+0xc/0x1c [mlx5_core]
[  157.990972 ]  __x64_sys_delete_module+0x15a/0x250
[  157.991398 ]  ? exit_to_user_mode_prepare+0xea/0x110
[  157.991840 ]  do_syscall_64+0x3d/0x90
[  157.992198 ]  entry_SYSCALL_64_after_hwframe+0x46/0xb0

Fixes: 04de7dda7394 ("net/mlx5e: Infrastructure for duplicated offloading of TC flows")
Fixes: 1418ddd96afd ("net/mlx5e: Duplicate offloaded TC eswitch rules under uplink LAG")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: DR, Fix crc32 calculation to work on big-endian (BE) CPUs

commit 1e5daf5565b61a96e570865091589afc9156e3d3 upstream.

When calculating crc for hash index we use the function crc32 that
calculates for little-endian (LE) arch.
Then we convert it to network endianness using htonl(), but it's wrong
to do the conversion in BE archs since the crc32 value is already LE.

The solution is to switch the bytes from the crc result for all types
of arc.

Fixes: 40416d8ede65 ("net/mlx5: DR, Replace CRC32 implementation to use kernel lib")
Signed-off-by: Erez Shitrit <erezsh@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5e: do as little as possible in napi poll when budget is 0

commit afbed3f74830163f9559579dee382cac3cff82da upstream.

NAPI gets called with budget of 0 from netpoll, which has interrupts
disabled. We should try to free some space on Tx rings and nothing
else.

Specifically do not try to handle XDP TX or try to refill Rx buffers -
we can't use the page pool from IRQ context. Don't check if IRQs moved,
either, that makes no sense in netpoll. Netpoll calls _all_ the rings
from whatever CPU it happens to be invoked on.

In general do as little as possible, the work quickly adds up when
there's tens of rings to poll.

The immediate stack trace I was seeing is:

    __do_softirq+0xd1/0x2c0
    __local_bh_enable_ip+0xc7/0x120
    </IRQ>
    <TASK>
    page_pool_put_defragged_page+0x267/0x320
    mlx5e_free_xdpsq_desc+0x99/0xd0
    mlx5e_poll_xdpsq_cq+0x138/0x3b0
    mlx5e_napi_poll+0xc3/0x8b0
    netpoll_poll_dev+0xce/0x150

AFAIU page pool takes a BH lock, releases it and since BH is now
enabled tries to run softirqs.

Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Fixes: 60bbf7eeef10 ("mlx5: use page_pool for xdp_return_frame call")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5e: Use correct encap attribute during invalidation

commit be071cdb167fc3e25fe81922166b3d499d23e8ac upstream.

With introduction of post action infrastructure most of the users of encap
attribute had been modified in order to obtain the correct attribute by
calling mlx5e_tc_get_encap_attr() helper instead of assuming encap action
is always on default attribute. However, the cited commit didn't modify
mlx5e_invalidate_encap() which prevents it from destroying correct modify
header action which leads to a warning [0]. Fix the issue by using correct
attribute.

[0]:

Feb 21 09:47:35 c-237-177-40-045 kernel: WARNING: CPU: 17 PID: 654 at drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:684 mlx5e_tc_attach_mod_hdr+0x1cc/0x230 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: RIP: 0010:mlx5e_tc_attach_mod_hdr+0x1cc/0x230 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: Call Trace:
Feb 21 09:47:35 c-237-177-40-045 kernel:  <TASK>
Feb 21 09:47:35 c-237-177-40-045 kernel:  mlx5e_tc_fib_event_work+0x8e3/0x1f60 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel:  ? mlx5e_take_all_encap_flows+0xe0/0xe0 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel:  ? lock_downgrade+0x6d0/0x6d0
Feb 21 09:47:35 c-237-177-40-045 kernel:  ? lockdep_hardirqs_on_prepare+0x273/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel:  ? lockdep_hardirqs_on_prepare+0x273/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel:  process_one_work+0x7c2/0x1310
Feb 21 09:47:35 c-237-177-40-045 kernel:  ? lockdep_hardirqs_on_prepare+0x3f0/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel:  ? pwq_dec_nr_in_flight+0x230/0x230
Feb 21 09:47:35 c-237-177-40-045 kernel:  ? rwlock_bug.part.0+0x90/0x90
Feb 21 09:47:35 c-237-177-40-045 kernel:  worker_thread+0x59d/0xec0
Feb 21 09:47:35 c-237-177-40-045 kernel:  ? __kthread_parkme+0xd9/0x1d0

Fixes: 8300f225268b ("net/mlx5e: Create new flow attr for multi table actions")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5e: Fix deadlock in tc route query code

commit 691c041bf20899fc13c793f92ba61ab660fa3a30 upstream.

Cited commit causes ABBA deadlock[0] when peer flows are created while
holding the devcom rw semaphore. Due to peer flows offload implementation
the lock is taken much higher up the call chain and there is no obvious way
to easily fix the deadlock. Instead, since tc route query code needs the
peer eswitch structure only to perform a lookup in xarray and doesn't
perform any sleeping operations with it, refactor the code for lockless
execution in following ways:

- RCUify the devcom 'data' pointer. When resetting the pointer
synchronously wait for RCU grace period before returning. This is fine
since devcom is currently only used for synchronization of
pairing/unpairing of eswitches which is rare and already expensive as-is.

- Wrap all usages of 'paired' boolean in {READ|WRITE}_ONCE(). The flag has
already been used in some unlocked contexts without proper
annotations (e.g. users of mlx5_devcom_is_paired() function), but it wasn't
an issue since all relevant code paths checked it again after obtaining the
devcom semaphore. Now it is also used by mlx5_devcom_get_peer_data_rcu() as
"best effort" check to return NULL when devcom is being unpaired. Note that
while RCU read lock doesn't prevent the unpaired flag from being changed
concurrently it still guarantees that reader can continue to use 'data'.

- Refactor mlx5e_tc_query_route_vport() function to use new
mlx5_devcom_get_peer_data_rcu() API which fixes the deadlock.

[0]:

[  164.599612] ======================================================
[  164.600142] WARNING: possible circular locking dependency detected
[  164.600667] 6.3.0-rc3+ #1 Not tainted
[  164.601021] ------------------------------------------------------
[  164.601557] handler1/3456 is trying to acquire lock:
[  164.601998] ffff88811f1714b0 (&esw->offloads.encap_tbl_lock){+.+.}-{3:3}, at: mlx5e_attach_encap+0xd8/0x8b0 [mlx5_core]
[  164.603078]
               but task is already holding lock:
[  164.603617] ffff88810137fc98 (&comp->sem){++++}-{3:3}, at: mlx5_devcom_get_peer_data+0x37/0x80 [mlx5_core]
[  164.604459]
               which lock already depends on the new lock.

[  164.605190]
               the existing dependency chain (in reverse order) is:
[  164.605848]
               -> #1 (&comp->sem){++++}-{3:3}:
[  164.606380]        down_read+0x39/0x50
[  164.606772]        mlx5_devcom_get_peer_data+0x37/0x80 [mlx5_core]
[  164.607336]        mlx5e_tc_query_route_vport+0x86/0xc0 [mlx5_core]
[  164.607914]        mlx5e_tc_tun_route_lookup+0x1a4/0x1d0 [mlx5_core]
[  164.608495]        mlx5e_attach_decap_route+0xc6/0x1e0 [mlx5_core]
[  164.609063]        mlx5e_tc_add_fdb_flow+0x1ea/0x360 [mlx5_core]
[  164.609627]        __mlx5e_add_fdb_flow+0x2d2/0x430 [mlx5_core]
[  164.610175]        mlx5e_configure_flower+0x952/0x1a20 [mlx5_core]
[  164.610741]        tc_setup_cb_add+0xd4/0x200
[  164.611146]        fl_hw_replace_filter+0x14c/0x1f0 [cls_flower]
[  164.611661]        fl_change+0xc95/0x18a0 [cls_flower]
[  164.612116]        tc_new_tfilter+0x3fc/0xd20
[  164.612516]        rtnetlink_rcv_msg+0x418/0x5b0
[  164.612936]        netlink_rcv_skb+0x54/0x100
[  164.613339]        netlink_unicast+0x190/0x250
[  164.613746]        netlink_sendmsg+0x245/0x4a0
[  164.614150]        sock_sendmsg+0x38/0x60
[  164.614522]        ____sys_sendmsg+0x1d0/0x1e0
[  164.614934]        ___sys_sendmsg+0x80/0xc0
[  164.615320]        __sys_sendmsg+0x51/0x90
[  164.615701]        do_syscall_64+0x3d/0x90
[  164.616083]        entry_SYSCALL_64_after_hwframe+0x46/0xb0
[  164.616568]
               -> #0 (&esw->offloads.encap_tbl_lock){+.+.}-{3:3}:
[  164.617210]        __lock_acquire+0x159e/0x26e0
[  164.617638]        lock_acquire+0xc2/0x2a0
[  164.618018]        __mutex_lock+0x92/0xcd0
[  164.618401]        mlx5e_attach_encap+0xd8/0x8b0 [mlx5_core]
[  164.618943]        post_process_attr+0x153/0x2d0 [mlx5_core]
[  164.619471]        mlx5e_tc_add_fdb_flow+0x164/0x360 [mlx5_core]
[  164.620021]        __mlx5e_add_fdb_flow+0x2d2/0x430 [mlx5_core]
[  164.620564]        mlx5e_configure_flower+0xe33/0x1a20 [mlx5_core]
[  164.621125]        tc_setup_cb_add+0xd4/0x200
[  164.621531]        fl_hw_replace_filter+0x14c/0x1f0 [cls_flower]
[  164.622047]        fl_change+0xc95/0x18a0 [cls_flower]
[  164.622500]        tc_new_tfilter+0x3fc/0xd20
[  164.622906]        rtnetlink_rcv_msg+0x418/0x5b0
[  164.623324]        netlink_rcv_skb+0x54/0x100
[  164.623727]        netlink_unicast+0x190/0x250
[  164.624138]        netlink_sendmsg+0x245/0x4a0
[  164.624544]        sock_sendmsg+0x38/0x60
[  164.624919]        ____sys_sendmsg+0x1d0/0x1e0
[  164.625340]        ___sys_sendmsg+0x80/0xc0
[  164.625731]        __sys_sendmsg+0x51/0x90
[  164.626117]        do_syscall_64+0x3d/0x90
[  164.626502]        entry_SYSCALL_64_after_hwframe+0x46/0xb0
[  164.626995]
               other info that might help us debug this:

[  164.627725]  Possible unsafe locking scenario:

[  164.628268]        CPU0                    CPU1
[  164.628683]        ----                    ----
[  164.629098]   lock(&comp->sem);
[  164.629421]                                lock(&esw->offloads.encap_tbl_lock);
[  164.630066]                                lock(&comp->sem);
[  164.630555]   lock(&esw->offloads.encap_tbl_lock);
[  164.630993]
                *** DEADLOCK ***

[  164.631575] 3 locks held by handler1/3456:
[  164.631962]  #0: ffff888124b75130 (&block->cb_lock){++++}-{3:3}, at: tc_setup_cb_add+0x5b/0x200
[  164.632703]  #1: ffff888116e512b8 (&esw->mode_lock){++++}-{3:3}, at: mlx5_esw_hold+0x39/0x50 [mlx5_core]
[  164.633552]  #2: ffff88810137fc98 (&comp->sem){++++}-{3:3}, at: mlx5_devcom_get_peer_data+0x37/0x80 [mlx5_core]
[  164.634435]
               stack backtrace:
[  164.634883] CPU: 17 PID: 3456 Comm: handler1 Not tainted 6.3.0-rc3+ #1
[  164.635431] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[  164.636340] Call Trace:
[  164.636616]  <TASK>
[  164.636863]  dump_stack_lvl+0x47/0x70
[  164.637217]  check_noncircular+0xfe/0x110
[  164.637601]  __lock_acquire+0x159e/0x26e0
[  164.637977]  ? mlx5_cmd_set_fte+0x5b0/0x830 [mlx5_core]
[  164.638472]  lock_acquire+0xc2/0x2a0
[  164.638828]  ? mlx5e_attach_encap+0xd8/0x8b0 [mlx5_core]
[  164.639339]  ? lock_is_held_type+0x98/0x110
[  164.639728]  __mutex_lock+0x92/0xcd0
[  164.640074]  ? mlx5e_attach_encap+0xd8/0x8b0 [mlx5_core]
[  164.640576]  ? __lock_acquire+0x382/0x26e0
[  164.640958]  ? mlx5e_attach_encap+0xd8/0x8b0 [mlx5_core]
[  164.641468]  ? mlx5e_attach_encap+0xd8/0x8b0 [mlx5_core]
[  164.641965]  mlx5e_attach_encap+0xd8/0x8b0 [mlx5_core]
[  164.642454]  ? lock_release+0xbf/0x240
[  164.642819]  post_process_attr+0x153/0x2d0 [mlx5_core]
[  164.643318]  mlx5e_tc_add_fdb_flow+0x164/0x360 [mlx5_core]
[  164.643835]  __mlx5e_add_fdb_flow+0x2d2/0x430 [mlx5_core]
[  164.644340]  mlx5e_configure_flower+0xe33/0x1a20 [mlx5_core]
[  164.644862]  ? lock_acquire+0xc2/0x2a0
[  164.645219]  tc_setup_cb_add+0xd4/0x200
[  164.645588]  fl_hw_replace_filter+0x14c/0x1f0 [cls_flower]
[  164.646067]  fl_change+0xc95/0x18a0 [cls_flower]
[  164.646488]  tc_new_tfilter+0x3fc/0xd20
[  164.646861]  ? tc_del_tfilter+0x810/0x810
[  164.647236]  rtnetlink_rcv_msg+0x418/0x5b0
[  164.647621]  ? rtnl_setlink+0x160/0x160
[  164.647982]  netlink_rcv_skb+0x54/0x100
[  164.648348]  netlink_unicast+0x190/0x250
[  164.648722]  netlink_sendmsg+0x245/0x4a0
[  164.649090]  sock_sendmsg+0x38/0x60
[  164.649434]  ____sys_sendmsg+0x1d0/0x1e0
[  164.649804]  ? copy_msghdr_from_user+0x6d/0xa0
[  164.650213]  ___sys_sendmsg+0x80/0xc0
[  164.650563]  ? lock_acquire+0xc2/0x2a0
[  164.650926]  ? lock_acquire+0xc2/0x2a0
[  164.651286]  ? __fget_files+0x5/0x190
[  164.651644]  ? find_held_lock+0x2b/0x80
[  164.652006]  ? __fget_files+0xb9/0x190
[  164.652365]  ? lock_release+0xbf/0x240
[  164.652723]  ? __fget_files+0xd3/0x190
[  164.653079]  __sys_sendmsg+0x51/0x90
[  164.653435]  do_syscall_64+0x3d/0x90
[  164.653784]  entry_SYSCALL_64_after_hwframe+0x46/0xb0
[  164.654229] RIP: 0033:0x7f378054f8bd
[  164.654577] Code: 28 89 54 24 1c 48 89 74 24 10 89 7c 24 08 e8 6a c3 f4 ff 8b 54 24 1c 48 8b 74 24 10 41 89 c0 8b 7c 24 08 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 33 44 89 c7 48 89 44 24 08 e8 be c3 f4 ff 48
[  164.656041] RSP: 002b:00007f377fa114b0 EFLAGS: 00000293 ORIG_RAX: 000000000000002e
[  164.656701] RAX: ffffffffffffffda RBX: 0000000000000001 RCX: 00007f378054f8bd
[  164.657297] RDX: 0000000000000000 RSI: 00007f377fa11540 RDI: 0000000000000014
[  164.657885] RBP: 00007f377fa12278 R08: 0000000000000000 R09: 000000000000015c
[  164.658472] R10: 00007f377fa123d0 R11: 0000000000000293 R12: 0000560962d99bd0
[  164.665317] R13: 0000000000000000 R14: 0000560962d99bd0 R15: 00007f377fa11540

Fixes: f9d196bd632b ("net/mlx5e: Use correct eswitch for stack devices with lag")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5e: Fix SQ wake logic in ptp napi_poll context

commit 7aa50380191635e5897a773f272829cc961a2be5 upstream.

Check in the mlx5e_ptp_poll_ts_cq context if the ptp tx sq should be woken
up. Before change, the ptp tx sq may never wake up if the ptp tx ts skb
fifo is full when mlx5e_poll_tx_cq checks if the queue should be woken up.

Fixes: 1880bc4e4a96 ("net/mlx5e: Add TX port timestamp support")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

platform/mellanox: mlxbf-pmc: fix sscanf() error checking

commit 95e4b25192e9238fd2dbe85d96dd2f8fd1ce9d14 upstream.

The sscanf() function never returns negatives.  It returns the number of
items successfully read.

Fixes: 1a218d312e65 ("platform/mellanox: mlxbf-pmc: Add Mellanox BlueField PMC driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/4ccdfd28-099b-40bf-8d77-ad4ea2e76b93@kili.mountain
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

forcedeth: Fix an error handling path in nv_probe()

commit 5b17a4971d3b2a073f4078dd65331efbe35baa2d upstream.

If an error occures after calling nv_mgmt_acquire_sema(), it should be
undone with a corresponding nv_mgmt_release_sema() call.

Add it in the error handling path of the probe as already done in the
remove function.

Fixes: cac1c52c3621 ("forcedeth: mgmt unit interface")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Zhu Yanjun <zyjzyj2000@gmail.com>
Link: https://lore.kernel.org/r/355e9a7d351b32ad897251b6f81b5886fcdc6766.1684571393.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sctp: fix an issue that plpmtu can never go to complete state

commit 6ca328e985cd995dfd1d5de44046e6074f853fbb upstream.

When doing plpmtu probe, the probe size is growing every time when it
receives the ACK during the Search state until the probe fails. When
the failure occurs, pl.probe_high is set and it goes to the Complete
state.

However, if the link pmtu is huge, like 65535 in loopback_dev, the probe
eventually keeps using SCTP_MAX_PLPMTU as the probe size and never fails.
Because of that, pl.probe_high can not be set, and the plpmtu probe can
never go to the Complete state.

Fix it by setting pl.probe_high to SCTP_MAX_PLPMTU when the probe size
grows to SCTP_MAX_PLPMTU in sctp_transport_pl_recv(). Also, not allow
the probe size greater than SCTP_MAX_PLPMTU in the Complete state.

Fixes: b87641aff9e7 ("sctp: do state transition when a probe succeeds on HB ACK recv path")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cxl: Wait Memory_Info_Valid before access memory related info

commit ce17ad0d54985e2595a3e615fda31df61808a08c upstream.

The Memory_Info_Valid bit (CXL 3.0 8.1.3.8.2) indicates that the CXL
Range Size High and Size Low registers are valid. The bit must be set
within 1 second of reset deassertion to the device. Check valid bit
before we check the Memory_Active bit when waiting for
cxl_await_media_ready() to ensure that the memory info is valid for
consumption. Also ensures both DVSEC ranges 1 and 2 are ready if DVSEC
Capability indicates they are both supported.

Fixes: 523e594d9cc0 ("cxl/pci: Implement wait for media active")
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/168444687469.3134781.11033518965387297327.stgit@djiang5-mobl3
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: Intel: avs: Access path components under lock

commit d849996f7458042af803b7d15a181922834c5249 upstream.

Path and its components should be accessed under lock to prevent
problems with one thread modifying them while other tries to read.

Fixes: c8c960c10971 ("ASoC: Intel: avs: APL-based platforms support")
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230519201711.4073845-3-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: Intel: avs: Fix declaration of enum avs_channel_config

commit 1cf036deebcdec46d6348842bd2f8931202fd4cd upstream.

Constant 'C4_CHANNEL' does not exist on the firmware side. Value 0xC is
reserved for 'C7_1' instead.

Fixes: 580a5912d1fe ("ASoC: Intel: avs: Declare module configuration types")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230519201711.4073845-5-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: Intel: Skylake: Fix declaration of enum skl_ch_cfg

commit 95109657471311601b98e71f03d0244f48dc61bb upstream.

Constant 'C4_CHANNEL' does not exist on the firmware side. Value 0xC is
reserved for 'C7_1' instead.

Fixes: 04afbbbb1cba ("ASoC: Intel: Skylake: Update the topology interface structure")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230519201711.4073845-4-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/show_trace_log_lvl: Ensure stack pointer is aligned, again

commit 2e4be0d011f21593c6b316806779ba1eba2cd7e0 upstream.

The commit e335bb51cc15 ("x86/unwind: Ensure stack pointer is aligned")
tried to align the stack pointer in show_trace_log_lvl(), otherwise the
"stack < stack_info.end" check can't guarantee that the last read does
not go past the end of the stack.

However, we have the same problem with the initial value of the stack
pointer, it can also be unaligned. So without this patch this trivial
kernel module

#include <linux/module.h>

static int init(void)
{
asm volatile("sub    $0x4,%rsp");
dump_stack();
asm volatile("add    $0x4,%rsp");

return -EAGAIN;
}

module_init(init);
MODULE_LICENSE("GPL");

crashes the kernel.

Fixes: e335bb51cc15 ("x86/unwind: Ensure stack pointer is aligned")
Signed-off-by: Vernon Lovejoy <vlovejoy@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: https://lore.kernel.org/r/20230512104232.GA10227@redhat.com
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen/pvcalls-back: fix double frees with pvcalls_new_active_socket()

commit 8fafac202d18230bb9926bda48e563fd2cce2a4f upstream.

In the pvcalls_new_active_socket() function, most error paths call
pvcalls_back_release_active(fedata->dev, fedata, map) which calls
sock_release() on "sock".  The bug is that the caller also frees sock.

Fix this by making every error path in pvcalls_new_active_socket()
release the sock, and don't free it in the caller.

Fixes: 5db4d286a8ef ("xen/pvcalls: implement connect command")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/e5f98dc2-0305-491f-a860-71bbd1398a2f@kili.mountain
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/pci/xen: populate MSI sysfs entries

commit 335b4223466dd75f9f3ea4918187afbadd22e5c8 upstream.

Commit bf5e758f02fc ("genirq/msi: Simplify sysfs handling") reworked the
creation of sysfs entries for MSI IRQs. The creation used to be in
msi_domain_alloc_irqs_descs_locked after calling ops->domain_alloc_irqs.
Then it moved into __msi_domain_alloc_irqs which is an implementation of
domain_alloc_irqs. However, Xen comes with the only other implementation
of domain_alloc_irqs and hence doesn't run the sysfs population code
anymore.

Commit 6c796996ee70 ("x86/pci/xen: Fixup fallout from the PCI/MSI
overhaul") set the flag MSI_FLAG_DEV_SYSFS for the xen msi_domain_info
but that doesn't actually have an effect because Xen uses it's own
domain_alloc_irqs implementation.

Fix this by making use of the fallback functions for sysfs population.

Fixes: bf5e758f02fc ("genirq/msi: Simplify sysfs handling")
Signed-off-by: Maximilian Heyne <mheyne@amazon.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20230503131656.15928-1-mheyne@amazon.de
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: imx6qdl-mba6: Add missing pvcie-supply regulator

commit 91aa4b3782448a7a13baa8cbcdfd5fd19defcbd9 upstream.

This worked before by coincidence, as the regulator was probed and enabled
before PCI RC probe. But probe order changed since commit 259b93b21a9f
("regulator: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in
4.14") and PCIe supply is enabled after RC.
Fix this by adding the regulator to RC node.

The PCIe vaux regulator still needs to be enabled unconditionally for
Mini-PCIe USB-only devices.

Fixes: ef3846247b41 ("ARM: dts: imx6qdl: add TQ-Systems MBa6x device trees")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

coresight: Fix signedness bug in tmc_etr_buf_insert_barrier_packet()

commit f67bc15e526bb9920683ad6c1891ff9e08981335 upstream.

This code generates a Smatch warning:

    drivers/hwtracing/coresight/coresight-tmc-etr.c:947 tmc_etr_buf_insert_barrier_packet()
    error: uninitialized symbol 'bufp'.

The problem is that if tmc_sg_table_get_data() returns -EINVAL, then
when we test if "len < CORESIGHT_BARRIER_PKT_SIZE", the negative "len"
value is type promoted to a high unsigned long value which is greater
than CORESIGHT_BARRIER_PKT_SIZE.  Fix this bug by adding an explicit
check for error codes.

Fixes: 75f4e3619fe2 ("coresight: tmc-etr: Add transparent buffer management")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/7d33e244-d8b9-4c27-9653-883a13534b01@kili.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

platform/x86: ISST: Remove 8 socket limit

commit bbb320bfe2c3e9740fe89cfa0a7089b4e8bfc4ff upstream.

Stop restricting the PCI search to a range of PCI domains fed to
pci_get_domain_bus_and_slot().  Instead, use for_each_pci_dev() and
look at all PCI domains in one pass.

On systems with more than 8 sockets, this avoids error messages like
"Information: Invalid level, Can't get TDP control information at
specified levels on cpu 480" from the intel speed select utility.

Fixes: aa2ddd242572 ("platform/x86: ISST: Use numa node id for cpu pci dev mapping")
Signed-off-by: Steve Wahl <steve.wahl@hpe.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230519160420.2588475-1-steve.wahl@hpe.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

regulator: pca9450: Fix BUCK2 enable_mask

commit d67dada3e2524514b09496b9ee1df22d4507a280 upstream.

This fixes a copy & paste error.
No functional change intended, BUCK1_ENMODE_MASK equals BUCK2_ENMODE_MASK.

Fixes: 0935ff5f1f0a ("regulator: pca9450: add pca9450 pmic driver")
Originally-from: Robin Gong <yibin.gong@nxp.com
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de
Link: https://lore.kernel.org/r/20230512081935.2396180-1-alexander.stein@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fs: fix undefined behavior in bit shift for SB_NOUSER

commit f15afbd34d8fadbd375f1212e97837e32bc170cc upstream.

Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. It was spotted by UBSAN.

So let's just fix this by using the BIT() helper for all SB_* flags.

Fixes: e462ec50cb5f ("VFS: Differentiate mount flags (MS_*) from internal superblock flags")
Signed-off-by: Hao Ge <gehao@kylinos.cn>
Message-Id: <20230424051835.374204-1-gehao@kylinos.cn>
[brauner@kernel.org: use BIT() for all SB_* flags]
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

firmware: arm_ffa: Fix FFA device names for logical partitions

commit 19b8766459c41c6f318f8a548cc1c66dffd18363 upstream.

Each physical partition can provide multiple services each with UUID.
Each such service can be presented as logical partition with a unique
combination of VM ID and UUID. The number of distinct UUID in a system
will be less than or equal to the number of logical partitions.

However, currently it fails to register more than one logical partition
or service within a physical partition as the device name contains only
VM ID while both VM ID and UUID are maintained in the partition information.
The kernel complains with the below message:

  | sysfs: cannot create duplicate filename '/devices/arm-ffa-8001'
  | CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.3.0-rc7 #8
  | Hardware name: FVP Base RevC (DT)
  | Call trace:
  |  dump_backtrace+0xf8/0x118
  |  show_stack+0x18/0x24
  |  dump_stack_lvl+0x50/0x68
  |  dump_stack+0x18/0x24
  |  sysfs_create_dir_ns+0xe0/0x13c
  |  kobject_add_internal+0x220/0x3d4
  |  kobject_add+0x94/0x100
  |  device_add+0x144/0x5d8
  |  device_register+0x20/0x30
  |  ffa_device_register+0x88/0xd8
  |  ffa_setup_partitions+0x108/0x1b8
  |  ffa_init+0x2ec/0x3a4
  |  do_one_initcall+0xcc/0x240
  |  do_initcall_level+0x8c/0xac
  |  do_initcalls+0x54/0x94
  |  do_basic_setup+0x1c/0x28
  |  kernel_init_freeable+0x100/0x16c
  |  kernel_init+0x20/0x1a0
  |  ret_from_fork+0x10/0x20
  | kobject_add_internal failed for arm-ffa-8001 with -EEXIST, don't try to
  | register things with the same name in the same directory.
  | arm_ffa arm-ffa: unable to register device arm-ffa-8001 err=-17
  | ARM FF-A: ffa_setup_partitions: failed to register partition ID 0x8001

By virtue of being random enough to avoid collisions when generated in a
distributed system, there is no way to compress UUID keys to the number
of bits required to identify each. We can eliminate '-' in the name but
it is not worth eliminating 4 bytes and add unnecessary logic for doing
that. Also v1.0 doesn't provide the UUID of the partitions which makes
it hard to use the same for the device name.

So to keep it simple, let us alloc an ID using ida_alloc() and append the
same to "arm-ffa" to make up a unique device name. Also stash the id value
in ffa_dev to help freeing the ID later when the device is destroyed.

Fixes: e781858488b9 ("firmware: arm_ffa: Add initial FFA bus support for device enumeration")
Reported-by: Lucian Paul-Trifu <lucian.paul-trifu@arm.com>
Link: https://lore.kernel.org/r/20230419-ffa_fixes_6-4-v2-3-d9108e43a176@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

firmware: arm_ffa: Check if ffa_driver remove is present before executing

commit b71b55248a580e9c9befc4ae060539f1f8e477da upstream.

Currently ffa_drv->remove() is called unconditionally from
ffa_device_remove(). Since the driver registration doesn't check for it
and allows it to be registered without .remove callback, we need to check
for the presence of it before executing it from ffa_device_remove() to
above a NULL pointer dereference like the one below:

  | Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
  | Mem abort info:
  |   ESR = 0x0000000086000004
  |   EC = 0x21: IABT (current EL), IL = 32 bits
  |   SET = 0, FnV = 0
  |   EA = 0, S1PTW = 0
  |   FSC = 0x04: level 0 translation fault
  | user pgtable: 4k pages, 48-bit VAs, pgdp=0000000881cc8000
  | [0000000000000000] pgd=0000000000000000, p4d=0000000000000000
  | Internal error: Oops: 0000000086000004 [#1] PREEMPT SMP
  | CPU: 3 PID: 130 Comm: rmmod Not tainted 6.3.0-rc7 #6
  | Hardware name: FVP Base RevC (DT)
  | pstate: 63402809 (nZCv daif +PAN -UAO +TCO +DIT -SSBS BTYPE=-c)
  | pc : 0x0
  | lr : ffa_device_remove+0x20/0x2c
  | Call trace:
  |  0x0
  |  device_release_driver_internal+0x16c/0x260
  |  driver_detach+0x90/0xd0
  |  bus_remove_driver+0xdc/0x11c
  |  driver_unregister+0x30/0x54
  |  ffa_driver_unregister+0x14/0x20
  |  cleanup_module+0x18/0xeec
  |  __arm64_sys_delete_module+0x234/0x378
  |  invoke_syscall+0x40/0x108
  |  el0_svc_common+0xb4/0xf0
  |  do_el0_svc+0x30/0xa4
  |  el0_svc+0x2c/0x7c
  |  el0t_64_sync_handler+0x84/0xf0
  |  el0t_64_sync+0x190/0x194

Fixes: 244f5d597e1e ("firmware: arm_ffa: Add missing remove callback to ffa_bus_type")
Link: https://lore.kernel.org/r/20230419-ffa_fixes_6-4-v2-1-d9108e43a176@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

optee: fix uninited async notif value

commit 654d0310007146fae87b0c1a68f81e53ad519b14 upstream.

Fixes an uninitialized variable in irq_handler() that could lead to
unpredictable behavior in case OP-TEE fails to handle SMC function ID
OPTEE_SMC_GET_ASYNC_NOTIF_VALUE. This change ensures that in that case
get_async_notif_value() properly reports there are no notification
event.

Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/202304200755.OoiuclDZ-lkp@intel.com/
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/all/d9b7f69b-c737-4cb3-8e74-79fe00c934f9@kili.mountain/
Fixes: 6749e69c4dad ("optee: add asynchronous notifications")
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

power: supply: sbs-charger: Fix INHIBITED bit for Status reg

commit b2f2a3c9800208b0db2c2e34b05323757117faa2 upstream.

CHARGE_INHIBITED bit position of the ChargerStatus register is actually
0 not 1. This patch corrects it.

Fixes: feb583e37f8a8 ("power: supply: add sbs-charger driver")
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

power: supply: bq24190: Call power_supply_changed() after updating input current

commit 77c2a3097d7029441e8a91aa0de1b4e5464593da upstream.

The bq24192 model relies on external charger-type detection and once
that is done the bq24190_charger code will update the input current.

In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).

On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current. This allows the fuel-gauge driver to timely recheck
if the battery is charging after the new input current has been applied
and then it can immediately notify userspace about this.

Fixes: 18f8e6f695ac ("power: supply: bq24190_charger: Get input_current_limit from our supplier")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

power: supply: bq25890: Call power_supply_changed() after updating input current or voltage

commit ad3d9c779b1f09f3f3a6fefd07af407c7bc7c9a7 upstream.

The bq25892 model relies on external charger-type detection and once
that is done the bq25890_charger code will update the input current
and if pumpexpress is used also the input voltage.

In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).

On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current or voltage. This allows the fuel-gauge driver
to timely recheck if the battery is charging after the new input
settings have been applied and then it can immediately notify
userspace about this.

Fixes: 48f45b094dbb ("power: supply: bq25890: Support higher charging voltages through Pump Express+ protocol")
Fixes: eab25b4f93aa ("power: supply: bq25890: On the bq25892 set the IINLIM based on external charger detection")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

power: supply: bq27xxx: After charger plug in/out wait 0.5s for things to stabilize

commit 59a99cd462fbdf71f4e845e09f37783035088b4f upstream.

bq27xxx_external_power_changed() gets called when the charger is plugged
in or out. Rather then immediately scheduling an update wait 0.5 seconds
for things to stabilize, so that e.g. the (dis)charge current is stable
when bq27xxx_battery_update() runs.

Fixes: 740b755a3b34 ("bq27x00: Poll battery state")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

power: supply: bq27xxx: Ensure power_supply_changed() is called on current sign changes

commit 939a116142012926e25de0ea6b7e2f8d86a5f1b6 upstream.

On gauges where the current register is signed, there is no charging
flag in the flags register. So only checking flags will not result
in power_supply_changed() getting called when e.g. a charger is plugged
in and the current sign changes from negative (discharging) to
positive (charging).

This causes userspace's notion of the status to lag until userspace
does a poll.

And when a power_supply_leds.c LED trigger is used to indicate charging
status with a LED, this LED will lag until the capacity percentage
changes, which may take many minutes (because the LED trigger only is
updated on power_supply_changed() calls).

Fix this by calling bq27xxx_battery_current_and_status() on gauges with
a signed current register and checking if the status has changed.

Fixes: 297a533b3e62 ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

power: supply: bq27xxx: Move bq27xxx_battery_update() down

commit ff4c4a2a4437a6d03787c7aafb2617f20c3ef45f upstream.

Move the bq27xxx_battery_update() functions to below
the bq27xxx_battery_current_and_status() function.

This is just moving a block of text, no functional changes.

This is a preparation patch for making bq27xxx_battery_update() check
the status and have it call power_supply_changed() on status changes.

Fixes: 297a533b3e62 ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

power: supply: bq27xxx: Add cache parameter to bq27xxx_battery_current_and_status()

commit 35092c5819f8c5acc7bafe3fdbb13d6307c4f5e1 upstream.

Add a cache parameter to bq27xxx_battery_current_and_status() so that
it can optionally use cached flags instead of re-reading them itself.

This is a preparation patch for making bq27xxx_battery_update() check
the status and have it call power_supply_changed() on status changes.

Fixes: 297a533b3e62 ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

power: supply: bq27xxx: Fix poll_interval handling and races on remove

commit c00bc80462afc7963f449d7f21d896d2f629cacc upstream.

Before this patch bq27xxx_battery_teardown() was setting poll_interval = 0
to avoid bq27xxx_battery_update() requeuing the delayed_work item.

There are 2 problems with this:

1. If the driver is unbound through sysfs, rather then the module being
   rmmod-ed, this changes poll_interval unexpectedly

2. This is racy, after it being set poll_interval could be changed
   before bq27xxx_battery_update() checks it through
   /sys/module/bq27xxx_battery/parameters/poll_interval

Fix this by added a removed attribute to struct bq27xxx_device_info and
using that instead of setting poll_interval to 0.

There also is another poll_interval related race on remove(), writing
/sys/module/bq27xxx_battery/parameters/poll_interval will requeue
the delayed_work item for all devices on the bq27xxx_battery_devices
list and the device being removed was only removed from that list
after cancelling the delayed_work item.

Fix this by moving the removal from the bq27xxx_battery_devices list
to before cancelling the delayed_work item.

Fixes: 8cfaaa811894 ("bq27x00_battery: Fix OOPS caused by unregistring bq27x00 driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

power: supply: bq27xxx: Fix I2C IRQ race on remove

commit 444ff00734f3878cd54ddd1ed5e2e6dbea9326d5 upstream.

devm_request_threaded_irq() requested IRQs are only free-ed after
the driver's remove function has ran. So the IRQ could trigger and
call bq27xxx_battery_update() after bq27xxx_battery_teardown() has
already run.

Switch to explicitly free-ing the IRQ in bq27xxx_battery_i2c_remove()
to fix this.

Fixes: 8807feb91b76 ("power: bq27xxx_battery: Add interrupt handling support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

power: supply: bq27xxx: Fix bq27xxx_battery_update() race condition

commit 5c34c0aef185dcd10881847b9ebf20046aa77cb4 upstream.

bq27xxx_battery_update() assumes / requires that it is only run once,
not multiple times at the same time. But there are 3 possible callers:

1. bq27xxx_battery_poll() delayed_work item handler
2. bq27xxx_battery_irq_handler_thread() I2C IRQ handler
3. bq27xxx_battery_setup()

And there is no protection against these racing with each other,
fix this race condition by making all callers take di->lock:

- Rename bq27xxx_battery_update() to bq27xxx_battery_update_unlocked()

- Add new bq27xxx_battery_update() which takes di->lock and then calls
  bq27xxx_battery_update_unlocked()

- Make stale cache check code in bq27xxx_battery_get_property(), which
  already takes di->lock directly to check the jiffies, call
  bq27xxx_battery_update_unlocked() instead of messing with
  the delayed_work item

- Make bq27xxx_battery_update_unlocked() mod the delayed-work item
  so that the next poll is delayed to poll_interval milliseconds after
  the last update independent of the source of the update

Fixes: 740b755a3b34 ("bq27x00: Poll battery state")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

power: supply: mt6360: add a check of devm_work_autocancel in mt6360_charger_probe

commit 4cbb0d358883a27e432714b5256f0362946f5e25 upstream.

devm_work_autocancel may fail, add a check and return early.

Fixes: 0402e8ebb8b86 ("power: supply: mt6360_charger: add MT6360 charger support")
Signed-off-by: Kang Chen <void0red@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

power: supply: leds: Fix blink to LED on transition

commit e4484643991e0f6b89060092563f0dbab9450cbb upstream.

When a battery's status changes from charging to full then
the charging-blink-full-solid trigger tries to change
the LED from blinking to solid/on.

As is documented in include/linux/leds.h to deactivate blinking /
to make the LED solid a LED_OFF must be send:

"""
         * Deactivate blinking again when the brightness is set to LED_OFF
         * via the brightness_set() callback.
"""

led_set_brighness() calls with a brightness value other then 0 / LED_OFF
merely change the brightness of the LED in its on state while it is
blinking.

So power_supply_update_bat_leds() must first send a LED_OFF event
before the LED_FULL to disable blinking.

Fixes: 6501f728c56f ("power_supply: Add new LED trigger charging-blink-solid-full")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: mapchars mount option ignored

commit cb8b02fd6343228966324528adf920bfb8b8e681 upstream.

There are two ways that special characters (not allowed in some
other operating systems like Windows, but allowed in POSIX) have
been mapped in the past ("SFU" and "SFM" mappings) to allow them
to be stored in a range reserved for special chars. The default
for Linux has been to use "mapposix" (ie the SFM mapping) but
the conversion to the new mount API in the 5.11 kernel broke
the ability to override the default mapping of the reserved
characters (like '?' and '*' and '\') via "mapchars" mount option.

This patch fixes that - so can now mount with "mapchars"
mount option to override the default ("mapposix" ie SFM) mapping.

Reported-by: Tyler Spivey <tspivey8@gmail.com>
Fixes: 24e0a1eff9e2 ("cifs: switch to new mount api")
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv6: Fix out-of-bounds access in ipv6_find_tlv()

commit 878ecb0897f4737a4c9401f3523fd49589025671 upstream.

optlen is fetched without checking whether there is more than one byte to parse.
It can lead to out-of-bounds access.

Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.

Fixes: c61a40432509 ("[IPV6]: Find option offset by type.")
Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lan966x: Fix unloading/loading of the driver

commit 600761245952d7f70280add6ce02894f1528992b upstream.

It was noticing that after a while when unloading/loading the driver and
sending traffic through the switch, it would stop working. It would stop
forwarding any traffic and the only way to get out of this was to do a
power cycle of the board. The root cause seems to be that the switch
core is initialized twice. Apparently initializing twice the switch core
disturbs the pointers in the queue systems in the HW, so after a while
it would stop sending the traffic.
Unfortunetly, it is not possible to use a reset of the switch here,
because the reset line is connected to multiple devices like MDIO,
SGPIO, FAN, etc. So then all the devices will get reseted when the
network driver will be loaded.
So the fix is to check if the core is initialized already and if that is
the case don't initialize it again.

Fixes: db8bcaad5393 ("net: lan966x: add the basic lan966x driver")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230522120038.3749026-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bpf: fix a memory leak in the LRU and LRU_PERCPU hash maps

commit b34ffb0c6d23583830f9327864b9c1f486003305 upstream.

The LRU and LRU_PERCPU maps allocate a new element on update before locking the
target hash table bucket. Right after that the maps try to lock the bucket.
If this fails, then maps return -EBUSY to the caller without releasing the
allocated element. This makes the element untracked: it doesn't belong to
either of free lists, and it doesn't belong to the hash table, so can't be
re-used; this eventually leads to the permanent -ENOMEM on LRU map updates,
which is unexpected. Fix this by returning the element to the local free list
if bucket locking fails.

Fixes: 20b6cc34ea74 ("bpf: Avoid hashtab deadlock with map_locked")
Signed-off-by: Anton Protopopov <aspsk@isovalent.com>
Link: https://lore.kernel.org/r/20230522154558.2166815-1-aspsk@isovalent.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bpf: Fix mask generation for 32-bit narrow loads of 64-bit fields

commit 0613d8ca9ab382caabe9ed2dceb429e9781e443f upstream.

A narrow load from a 64-bit context field results in a 64-bit load
followed potentially by a 64-bit right-shift and then a bitwise AND
operation to extract the relevant data.

In the case of a 32-bit access, an immediate mask of 0xffffffff is used
to construct a 64-bit BPP_AND operation which then sign-extends the mask
value and effectively acts as a glorified no-op. For example:

0: 61 10 00 00 00 00 00 00 r0 = *(u32 *)(r1 + 0)

results in the following code generation for a 64-bit field:

ldr x7, [x7] // 64-bit load
mov x10, #0xffffffffffffffff
and x7, x7, x10

Fix the mask generation so that narrow loads always perform a 32-bit AND
operation:

ldr x7, [x7] // 64-bit load
mov w10, #0xffffffff
and w7, w7, w10

Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Krzesimir Nowak <krzesimir@kinvolk.io>
Cc: Andrey Ignatov <rdna@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Fixes: 31fd85816dbe ("bpf: permits narrower load from bpf program context fields")
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20230518102528.1341-1-will@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

octeontx2-pf: Fix TSOv6 offload

commit de678ca38861f2eb58814048076dcf95ed1b5bf9 upstream.

HW adds segment size to the payload length
in the IPv6 header. Fix payload length to
just TCP header length instead of 'TCP header
size + IPv6 header size'.

Fixes: 86d7476078b8 ("octeontx2-pf: TCP segmentation offload support")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests: fib_tests: mute cleanup error message

commit d226b1df361988f885c298737d6019c863a25f26 upstream.

In the end of the test, there will be an error message induced by the
`ip netns del ns1` command in cleanup()

  Tests passed: 201
  Tests failed:   0
  Cannot remove namespace file "/run/netns/ns1": No such file or directory

This can even be reproduced with just `./fib_tests.sh -h` as we're
calling cleanup() on exit.

Redirect the error message to /dev/null to mute it.

V2: Update commit message and fixes tag.
V3: resubmit due to missing netdev ML in V2

Fixes: b60417a9f2b8 ("selftest: fib_tests: Always cleanup before exit")
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm: fix drmm_mutex_init()

commit c21f11d182c2180d8b90eaff84f574cfa845b250 upstream.

In mutex_init() lockdep identifies a lock by defining a special static
key for each lock class. However if we wrap the macro in a function,
like in drmm_mutex_init(), we end up generating:

int drmm_mutex_init(struct drm_device *dev, struct mutex *lock)
{
      static struct lock_class_key __key;

      __mutex_init((lock), "lock", &__key);
      ....
}

The static __key here is what lockdep uses to identify the lock class,
however since this is just a normal function the key here will be
created once, where all callers then use the same key. In effect the
mutex->depmap.key will be the same pointer for different
drmm_mutex_init() callers. This then results in impossible lockdep
splats since lockdep thinks completely unrelated locks are the same lock
class.

To fix this turn drmm_mutex_init() into a macro such that it generates a
different "static struct lock_class_key __key" for each invocation,
which looks to be inline with what mutex_init() wants.

v2:
  - Revamp the commit message with clearer explanation of the issue.
  - Rather export __drmm_mutex_release() than static inline.

Reported-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reported-by: Sarah Walker <sarah.walker@imgtec.com>
Fixes: e13f13e039dc ("drm: Add DRM-managed mutex_init()")
Cc: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Jocelyn Falempe <jfalempe@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230519090733.489019-1-matthew.auld@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: fix skb leak in __skb_tstamp_tx()

commit 8a02fb71d7192ff1a9a47c9d937624966c6e09af upstream.

Commit 50749f2dd685 ("tcp/udp: Fix memleaks of sk and zerocopy skbs with
TX timestamp.") added a call to skb_orphan_frags_rx() to fix leaks with
zerocopy skbs. But it ended up adding a leak of its own. When
skb_orphan_frags_rx() fails, the function just returns, leaking the skb
it just cloned. Free it before returning.

This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.

Fixes: 50749f2dd685 ("tcp/udp: Fix memleaks of sk and zerocopy skbs with TX timestamp.")
Signed-off-by: Pratyush Yadav <ptyadav@amazon.de>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20230522153020.32422-1-ptyadav@amazon.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: lpass: Fix for KASAN use_after_free out of bounds

commit 75e5fab7db0cecb6e16b22c34608f0b40a4c7cd1 upstream.

When we run syzkaller we get below Out of Bounds error.

"KASAN: slab-out-of-bounds Read in regcache_flat_read"

Below is the backtrace of the issue:

BUG: KASAN: slab-out-of-bounds in regcache_flat_read+0x10c/0x110
Read of size 4 at addr ffffff8088fbf714 by task syz-executor.4/14144
CPU: 6 PID: 14144 Comm: syz-executor.4 Tainted: G        W
Hardware name: Qualcomm Technologies, Inc. sc7280 CRD platform (rev5+) (DT)
Call trace:
dump_backtrace+0x0/0x4ec
show_stack+0x34/0x50
dump_stack_lvl+0xdc/0x11c
print_address_description+0x30/0x2d8
kasan_report+0x178/0x1e4
__asan_report_load4_noabort+0x44/0x50
regcache_flat_read+0x10c/0x110
regcache_read+0xf8/0x5a0
_regmap_read+0x45c/0x86c
_regmap_update_bits+0x128/0x290
regmap_update_bits_base+0xc0/0x15c
snd_soc_component_update_bits+0xa8/0x22c
snd_soc_component_write_field+0x68/0xd4
tx_macro_put_dec_enum+0x1d0/0x268
snd_ctl_elem_write+0x288/0x474

By Error checking and checking valid values issue gets rectifies.

Signed-off-by: Ravulapati Vishnu Vardhan Rao <quic_visr@quicinc.com
Link: https://lore.kernel.org/r/20230511112532.16106-1-quic_visr@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: radio-shark: Add endpoint checks

commit 76e31045ba030e94e72105c01b2e98f543d175ac upstream.

The syzbot fuzzer was able to provoke a WARNING from the radio-shark2
driver:

------------[ cut here ]------------
usb 1-1: BOGUS urb xfer, pipe 1 != type 3
WARNING: CPU: 0 PID: 3271 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed2/0x1880 drivers/usb/core/urb.c:504
Modules linked in:
CPU: 0 PID: 3271 Comm: kworker/0:3 Not tainted 6.1.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_submit_urb+0xed2/0x1880 drivers/usb/core/urb.c:504
Code: 7c 24 18 e8 00 36 ea fb 48 8b 7c 24 18 e8 36 1c 02 ff 41 89 d8 44 89 e1 4c 89 ea 48 89 c6 48 c7 c7 a0 b6 90 8a e8 9a 29 b8 03 <0f> 0b e9 58 f8 ff ff e8 d2 35 ea fb 48 81 c5 c0 05 00 00 e9 84 f7
RSP: 0018:ffffc90003876dd0 EFLAGS: 00010282
RAX: 0000000000000000 RBX: 0000000000000003 RCX: 0000000000000000
RDX: ffff8880750b0040 RSI: ffffffff816152b8 RDI: fffff5200070edac
RBP: ffff8880172d81e0 R08: 0000000000000005 R09: 0000000000000000
R10: 0000000080000000 R11: 0000000000000000 R12: 0000000000000001
R13: ffff8880285c5040 R14: 0000000000000002 R15: ffff888017158200
FS:  0000000000000000(0000) GS:ffff8880b9a00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffe03235b90 CR3: 000000000bc8e000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 <TASK>
 usb_start_wait_urb+0x101/0x4b0 drivers/usb/core/message.c:58
 usb_bulk_msg+0x226/0x550 drivers/usb/core/message.c:387
 shark_write_reg+0x1ff/0x2e0 drivers/media/radio/radio-shark2.c:88
...

The problem was caused by the fact that the driver does not check
whether the endpoints it uses are actually present and have the
appropriate types.  This can be fixed by adding a simple check of
these endpoints (and similarly for the radio-shark driver).

Link: https://syzkaller.appspot.com/bug?extid=4b3f8190f6e13b3efd74
Reported-and-tested-by: syzbot+4b3f8190f6e13b3efd74@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/e2858ab4-4adf-46e5-bbf6-c56742034547@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: sisusbvga: Add endpoint checks

commit df05a9b05e466a46725564528b277d0c570d0104 upstream.

The syzbot fuzzer was able to provoke a WARNING from the sisusbvga driver:

------------[ cut here ]------------
usb 1-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 1 PID: 26 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
Modules linked in:
CPU: 1 PID: 26 Comm: kworker/1:1 Not tainted 6.2.0-rc5-syzkaller-00199-g5af6ce704936 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/12/2023
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
Code: 7c 24 18 e8 6c 50 80 fb 48 8b 7c 24 18 e8 62 1a 01 ff 41 89 d8 44 89 e1 4c 89 ea 48 89 c6 48 c7 c7 60 b1 fa 8a e8 84 b0 be 03 <0f> 0b e9 58 f8 ff ff e8 3e 50 80 fb 48 81 c5 c0 05 00 00 e9 84 f7
RSP: 0018:ffffc90000a1ed18 EFLAGS: 00010282
RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000000
RDX: ffff888012783a80 RSI: ffffffff816680ec RDI: fffff52000143d95
RBP: ffff888079020000 R08: 0000000000000005 R09: 0000000000000000
R10: 0000000080000000 R11: 0000000000000000 R12: 0000000000000003
R13: ffff888017d33370 R14: 0000000000000003 R15: ffff888021213600
FS:  0000000000000000(0000) GS:ffff8880b9900000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00005592753a60b0 CR3: 0000000022899000 CR4: 00000000003506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 <TASK>
 sisusb_bulkout_msg drivers/usb/misc/sisusbvga/sisusbvga.c:224 [inline]
 sisusb_send_bulk_msg.constprop.0+0x904/0x1230 drivers/usb/misc/sisusbvga/sisusbvga.c:379
 sisusb_send_bridge_packet drivers/usb/misc/sisusbvga/sisusbvga.c:567 [inline]
 sisusb_do_init_gfxdevice drivers/usb/misc/sisusbvga/sisusbvga.c:2077 [inline]
 sisusb_init_gfxdevice+0x87b/0x4000 drivers/usb/misc/sisusbvga/sisusbvga.c:2177
 sisusb_probe+0x9cd/0xbe2 drivers/usb/misc/sisusbvga/sisusbvga.c:2869
...

The problem was caused by the fact that the driver does not check
whether the endpoints it uses are actually present and have the
appropriate types.  This can be fixed by adding a simple check of
the endpoints.

Link: https://syzkaller.appspot.com/bug?extid=23be03b56c5259385d79
Reported-and-tested-by: syzbot+23be03b56c5259385d79@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/48ef98f7-51ae-4f63-b8d3-0ef2004bb60a@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: core: Add routines for endpoint checks in old drivers

commit 13890626501ffda22b18213ddaf7930473da5792 upstream.

Many of the older USB drivers in the Linux USB stack were written
based simply on a vendor's device specification.  They use the
endpoint information in the spec and assume these endpoints will
always be present, with the properties listed, in any device matching
the given vendor and product IDs.

While that may have been true back then, with spoofing and fuzzing it
is not true any more.  More and more we are finding that those old
drivers need to perform at least a minimum of checking before they try
to use any endpoint other than ep0.

To make this checking as simple as possible, we now add a couple of
utility routines to the USB core.  usb_check_bulk_endpoints() and
usb_check_int_endpoints() take an interface pointer together with a
list of endpoint addresses (numbers and directions).  They check that
the interface's current alternate setting includes endpoints with
those addresses and that each of these endpoints has the right type:
bulk or interrupt, respectively.

Although we already have usb_find_common_endpoints() and related
routines meant for a similar purpose, they are not well suited for
this kind of checking.  Those routines find endpoints of various
kinds, but only one (either the first or the last) of each kind, and
they don't verify that the endpoints' addresses agree with what the
caller expects.

In theory the new routines could be more general: They could take a
particular altsetting as their argument instead of always using the
interface's current altsetting.  In practice I think this won't matter
too much; multiple altsettings tend to be used for transferring media
(audio or visual) over isochronous endpoints, not bulk or interrupt.
Drivers for such devices will generally require more sophisticated
checking than these simplistic routines provide.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/dd2c8e8c-2c87-44ea-ba17-c64b97e201c9@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

udplite: Fix NULL pointer dereference in __sk_mem_raise_allocated().

commit ad42a35bdfc6d3c0fc4cb4027d7b2757ce665665 upstream.

syzbot reported [0] a null-ptr-deref in sk_get_rmem0() while using
IPPROTO_UDPLITE (0x88):

  14:25:52 executing program 1:
  r0 = socket$inet6(0xa, 0x80002, 0x88)

We had a similar report [1] for probably sk_memory_allocated_add()
in __sk_mem_raise_allocated(), and commit c915fe13cbaa ("udplite: fix
NULL pointer dereference") fixed it by setting .memory_allocated for
udplite_prot and udplitev6_prot.

To fix the variant, we need to set either .sysctl_wmem_offset or
.sysctl_rmem.

Now UDP and UDPLITE share the same value for .memory_allocated, so we
use the same .sysctl_wmem_offset for UDP and UDPLITE.

[0]:
general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 0 PID: 6829 Comm: syz-executor.1 Not tainted 6.4.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/28/2023
RIP: 0010:sk_get_rmem0 include/net/sock.h:2907 [inline]
RIP: 0010:__sk_mem_raise_allocated+0x806/0x17a0 net/core/sock.c:3006
Code: c1 ea 03 80 3c 02 00 0f 85 23 0f 00 00 48 8b 44 24 08 48 8b 98 38 01 00 00 48 b8 00 00 00 00 00 fc ff df 48 89 da 48 c1 ea 03 <0f> b6 14 02 48 89 d8 83 e0 07 83 c0 03 38 d0 0f 8d 6f 0a 00 00 8b
RSP: 0018:ffffc90005d7f450 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffffc90004d92000
RDX: 0000000000000000 RSI: ffffffff88066482 RDI: ffffffff8e2ccbb8
RBP: ffff8880173f7000 R08: 0000000000000005 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000030000
R13: 0000000000000001 R14: 0000000000000340 R15: 0000000000000001
FS:  0000000000000000(0000) GS:ffff8880b9800000(0063) knlGS:00000000f7f1cb40
CS:  0010 DS: 002b ES: 002b CR0: 0000000080050033
CR2: 000000002e82f000 CR3: 0000000034ff0000 CR4: 00000000003506f0
Call Trace:
 <TASK>
 __sk_mem_schedule+0x6c/0xe0 net/core/sock.c:3077
 udp_rmem_schedule net/ipv4/udp.c:1539 [inline]
 __udp_enqueue_schedule_skb+0x776/0xb30 net/ipv4/udp.c:1581
 __udpv6_queue_rcv_skb net/ipv6/udp.c:666 [inline]
 udpv6_queue_rcv_one_skb+0xc39/0x16c0 net/ipv6/udp.c:775
 udpv6_queue_rcv_skb+0x194/0xa10 net/ipv6/udp.c:793
 __udp6_lib_mcast_deliver net/ipv6/udp.c:906 [inline]
 __udp6_lib_rcv+0x1bda/0x2bd0 net/ipv6/udp.c:1013
 ip6_protocol_deliver_rcu+0x2e7/0x1250 net/ipv6/ip6_input.c:437
 ip6_input_finish+0x150/0x2f0 net/ipv6/ip6_input.c:482
 NF_HOOK include/linux/netfilter.h:303 [inline]
 NF_HOOK include/linux/netfilter.h:297 [inline]
 ip6_input+0xa0/0xd0 net/ipv6/ip6_input.c:491
 ip6_mc_input+0x40b/0xf50 net/ipv6/ip6_input.c:585
 dst_input include/net/dst.h:468 [inline]
 ip6_rcv_finish net/ipv6/ip6_input.c:79 [inline]
 NF_HOOK include/linux/netfilter.h:303 [inline]
 NF_HOOK include/linux/netfilter.h:297 [inline]
 ipv6_rcv+0x250/0x380 net/ipv6/ip6_input.c:309
 __netif_receive_skb_one_core+0x114/0x180 net/core/dev.c:5491
 __netif_receive_skb+0x1f/0x1c0 net/core/dev.c:5605
 netif_receive_skb_internal net/core/dev.c:5691 [inline]
 netif_receive_skb+0x133/0x7a0 net/core/dev.c:5750
 tun_rx_batched+0x4b3/0x7a0 drivers/net/tun.c:1553
 tun_get_user+0x2452/0x39c0 drivers/net/tun.c:1989
 tun_chr_write_iter+0xdf/0x200 drivers/net/tun.c:2035
 call_write_iter include/linux/fs.h:1868 [inline]
 new_sync_write fs/read_write.c:491 [inline]
 vfs_write+0x945/0xd50 fs/read_write.c:584
 ksys_write+0x12b/0x250 fs/read_write.c:637
 do_syscall_32_irqs_on arch/x86/entry/common.c:112 [inline]
 __do_fast_syscall_32+0x65/0xf0 arch/x86/entry/common.c:178
 do_fast_syscall_32+0x33/0x70 arch/x86/entry/common.c:203
 entry_SYSENTER_compat_after_hwframe+0x70/0x82
RIP: 0023:0xf7f21579
Code: b8 01 10 06 03 74 b4 01 10 07 03 74 b0 01 10 08 03 74 d8 01 00 00 00 00 00 00 00 00 00 00 00 00 00 51 52 55 89 e5 0f 34 cd 80 <5d> 5a 59 c3 90 90 90 90 8d b4 26 00 00 00 00 8d b4 26 00 00 00 00
RSP: 002b:00000000f7f1c590 EFLAGS: 00000282 ORIG_RAX: 0000000000000004
RAX: ffffffffffffffda RBX: 00000000000000c8 RCX: 0000000020000040
RDX: 0000000000000083 RSI: 00000000f734e000 RDI: 0000000000000000
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000296 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
 </TASK>
Modules linked in:

Link: https://lore.kernel.org/netdev/CANaxB-yCk8hhP68L4Q2nFOJht8sqgXGGQO2AftpHs0u1xyGG5A@mail.gmail.com/
Fixes: 850cbaddb52d ("udp: use it's own memory accounting schema")
Reported-by: syzbot+444ca0907e96f7c5e48b@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=444ca0907e96f7c5e48b
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20230523163305.66466-1-kuniyu@amazon.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: fix stack overflow when LRO is disabled for virtual interfaces

commit ae9b15fbe63447bc1d3bba3769f409d17ca6fdf6 upstream.

When the virtual interface's feature is updated, it synchronizes the
updated feature for its own lower interface.
This propagation logic should be worked as the iteration, not recursively.
But it works recursively due to the netdev notification unexpectedly.
This problem occurs when it disables LRO only for the team and bonding
interface type.

       team0
         |
  +------+------+-----+-----+
  |      |      |     |     |
team1  team2  team3  ...  team200

If team0's LRO feature is updated, it generates the NETDEV_FEAT_CHANGE
event to its own lower interfaces(team1 ~ team200).
It is worked by netdev_sync_lower_features().
So, the NETDEV_FEAT_CHANGE notification logic of each lower interface
work iteratively.
But generated NETDEV_FEAT_CHANGE event is also sent to the upper
interface too.
upper interface(team0) generates the NETDEV_FEAT_CHANGE event for its own
lower interfaces again.
lower and upper interfaces receive this event and generate this
event again and again.
So, the stack overflow occurs.

But it is not the infinite loop issue.
Because the netdev_sync_lower_features() updates features before
generating the NETDEV_FEAT_CHANGE event.
Already synchronized lower interfaces skip notification logic.
So, it is just the problem that iteration logic is changed to the
recursive unexpectedly due to the notification mechanism.

Reproducer:

ip link add team0 type team
ethtool -K team0 lro on
for i in {1..200}
do
        ip link add team$i master team0 type team
        ethtool -K team$i lro on
done

ethtool -K team0 lro off

In order to fix it, the notifier_ctx member of bonding/team is introduced.

Reported-by: syzbot+60748c96cf5c6df8e581@syzkaller.appspotmail.com
Fixes: fd867d51f889 ("net/core: generic support for disabling netdev features down stack")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230517143010.3596250-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fbdev: udlfb: Fix endpoint check

commit ed9de4ed39875706607fb08118a58344ae6c5f42 upstream.

The syzbot fuzzer detected a problem in the udlfb driver, caused by an
endpoint not having the expected type:

usb 1-1: Read EDID byte 0 failed: -71
usb 1-1: Unable to get valid EDID from device/display
------------[ cut here ]------------
usb 1-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 0 PID: 9 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880
drivers/usb/core/urb.c:504
Modules linked in:
CPU: 0 PID: 9 Comm: kworker/0:1 Not tainted
6.4.0-rc1-syzkaller-00016-ga4422ff22142 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
04/28/2023
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
...
Call Trace:
 <TASK>
 dlfb_submit_urb+0x92/0x180 drivers/video/fbdev/udlfb.c:1980
 dlfb_set_video_mode+0x21f0/0x2950 drivers/video/fbdev/udlfb.c:315
 dlfb_ops_set_par+0x2a7/0x8d0 drivers/video/fbdev/udlfb.c:1111
 dlfb_usb_probe+0x149a/0x2710 drivers/video/fbdev/udlfb.c:1743

The current approach for this issue failed to catch the problem
because it only checks for the existence of a bulk-OUT endpoint; it
doesn't check whether this endpoint is the one that the driver will
actually use.

We can fix the problem by instead checking that the endpoint used by
the driver does exist and is bulk-OUT.

Reported-and-tested-by: syzbot+0e22d63dcebb802b9bc8@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Pavel Skripkin <paskripkin@gmail.com>
Fixes: aaf7dbe07385 ("video: fbdev: udlfb: properly check endpoint type")
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

debugobjects: Don't wake up kswapd from fill_pool()

commit eb799279fb1f9c63c520fe8c1c41cb9154252db6 upstream.

syzbot is reporting a lockdep warning in fill_pool() because the allocation
from debugobjects is using GFP_ATOMIC, which is (__GFP_HIGH | __GFP_KSWAPD_RECLAIM)
and therefore tries to wake up kswapd, which acquires kswapd_wait::lock.

Since fill_pool() might be called with arbitrary locks held, fill_pool()
should not assume that acquiring kswapd_wait::lock is safe.

Use __GFP_HIGH instead and remove __GFP_NORETRY as it is pointless for
!__GFP_DIRECT_RECLAIM allocation.

Fixes: 3ac7fe5a4aab ("infrastructure to debug (dynamic) objects")
Reported-by: syzbot <syzbot+fe0c72f0ccbb93786380@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/6577e1fa-b6ee-f2be-2414-a2b51b1c5e30@I-love.SAKURA.ne.jp
Closes: https://syzkaller.appspot.com/bug?extid=fe0c72f0ccbb93786380
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

irqchip/mips-gic: Use raw spinlock for gic_lock

commit 3d6a0e4197c04599d75d85a608c8bb16a630a38c upstream.

Since we may hold gic_lock in hardirq context, use raw spinlock
makes more sense given that it is for low-level interrupt handling
routine and the critical section is small.

Fixes BUG:

[    0.426106] =============================
[    0.426257] [ BUG: Invalid wait context ]
[    0.426422] 6.3.0-rc7-next-20230421-dirty #54 Not tainted
[    0.426638] -----------------------------
[    0.426766] swapper/0/1 is trying to lock:
[    0.426954] ffffffff8104e7b8 (gic_lock){....}-{3:3}, at: gic_set_type+0x30/08

Fixes: 95150ae8b330 ("irqchip: mips-gic: Implement irq_set_type callback")
Cc: stable@vger.kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230424103156.66753-3-jiaxun.yang@flygoat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

irqchip/mips-gic: Don't touch vl_map if a local interrupt is not routable

commit 2c6c9c049510163090b979ea5f92a68ae8d93c45 upstream.

When a GIC local interrupt is not routable, it's vl_map will be used
to control some internal states for core (providing IPTI, IPPCI, IPFDC
input signal for core). Overriding it will interfere core's intetrupt
controller.

Do not touch vl_map if a local interrupt is not routable, we are not
going to remap it.

Before dd098a0e0319 (" irqchip/mips-gic: Get rid of the reliance on
irq_cpu_online()"), if a local interrupt is not routable, then it won't
be requested from GIC Local domain, and thus gic_all_vpes_irq_cpu_online
won't be called for that particular interrupt.

Fixes: dd098a0e0319 (" irqchip/mips-gic: Get rid of the reliance on irq_cpu_online()")
Cc: stable@vger.kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230424103156.66753-2-jiaxun.yang@flygoat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/topology: Fix erroneous smp_num_siblings on Intel Hybrid platforms

commit edc0a2b5957652f4685ef3516f519f84807087db upstream.

Traditionally, all CPUs in a system have identical numbers of SMT
siblings.  That changes with hybrid processors where some logical CPUs
have a sibling and others have none.

Today, the CPU boot code sets the global variable smp_num_siblings when
every CPU thread is brought up. The last thread to boot will overwrite
it with the number of siblings of *that* thread. That last thread to
boot will "win". If the thread is a Pcore, smp_num_siblings == 2.  If it
is an Ecore, smp_num_siblings == 1.

smp_num_siblings describes if the *system* supports SMT.  It should
specify the maximum number of SMT threads among all cores.

Ensure that smp_num_siblings represents the system-wide maximum number
of siblings by always increasing its value. Never allow it to decrease.

On MeteorLake-P platform, this fixes a problem that the Ecore CPUs are
not updated in any cpu sibling map because the system is treated as an
UP system when probing Ecore CPUs.

Below shows part of the CPU topology information before and after the
fix, for both Pcore and Ecore CPU (cpu0 is Pcore, cpu 12 is Ecore).
...
-/sys/devices/system/cpu/cpu0/topology/package_cpus:000fff
-/sys/devices/system/cpu/cpu0/topology/package_cpus_list:0-11
+/sys/devices/system/cpu/cpu0/topology/package_cpus:3fffff
+/sys/devices/system/cpu/cpu0/topology/package_cpus_list:0-21
...
-/sys/devices/system/cpu/cpu12/topology/package_cpus:001000
-/sys/devices/system/cpu/cpu12/topology/package_cpus_list:12
+/sys/devices/system/cpu/cpu12/topology/package_cpus:3fffff
+/sys/devices/system/cpu/cpu12/topology/package_cpus_list:0-21

Notice that the "before" 'package_cpus_list' has only one CPU.  This
means that userspace tools like lscpu will see a little laptop like
an 11-socket system:

-Core(s) per socket:  1
-Socket(s):           11
+Core(s) per socket:  16
+Socket(s):           1

This is also expected to make the scheduler do rather wonky things
too.

[ dhansen: remove CPUID detail from changelog, add end user effects ]

CC: stable@kernel.org
Fixes: bbb65d2d365e ("x86: use cpuid vector 0xb when available for detecting cpu topology")
Fixes: 95f3d39ccf7a ("x86/cpu/topology: Provide detect_extended_topology_early()")
Suggested-by: Len Brown <len.brown@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/20230323015640.27906-1-rui.zhang%40intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf/x86/uncore: Correct the number of CHAs on SPR

commit 38776cc45eb7603df4735a0410f42cffff8e71a1 upstream.

The number of CHAs from the discovery table on some SPR variants is
incorrect, because of a firmware issue. An accurate number can be read
from the MSR UNC_CBO_CONFIG.

Fixes: 949b11381f81 ("perf/x86/intel/uncore: Add Sapphire Rapids server CHA support")
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Stephane Eranian <eranian@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230508140206.283708-1-kan.liang@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amd/amdgpu: limit one queue per gang

commit 5ee33d905f89c18d4b33da6e5eefdae6060502df upstream.

Limit one queue per gang in mes self test,
due to mes schq fw change.

Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests/memfd: Fix unknown type name build failure

Partially backport v6.3 commit 11f75a01448f ("selftests/memfd: add tests
for MFD_NOEXEC_SEAL MFD_EXEC") to fix an unknown type name build error.
In some systems, the __u64 typedef is not present due to differences in
system headers, causing compilation errors like this one:

fuse_test.c:64:8: error: unknown type name '__u64'
   64 | static __u64 mfd_assert_get_seals(int fd)

This header includes the  __u64 typedef which increases the likelihood
of successful compilation on a wider variety of systems.

Signed-off-by: Hardik Garg <hargar@linux.microsoft.com>
Reviewed-by: Tyler Hicks (Microsoft) <code@tyhicks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

binder: fix UAF of alloc->vma in race with munmap()

commit d1d8875c8c13517f6fd1ff8d4d3e1ac366a17e07 upstream.

[ cmllamas: clean forward port from commit 015ac18be7de ("binder: fix
  UAF of alloc->vma in race with munmap()") in 5.10 stable. It is needed
  in mainline after the revert of commit a43cfc87caaf ("android: binder:
  stop saving a pointer to the VMA") as pointed out by Liam. The commit
  log and tags have been tweaked to reflect this. ]

In commit 720c24192404 ("ANDROID: binder: change down_write to
down_read") binder assumed the mmap read lock is sufficient to protect
alloc->vma inside binder_update_page_range(). This used to be accurate
until commit dd2283f2605e ("mm: mmap: zap pages with read mmap_sem in
munmap"), which now downgrades the mmap_lock after detaching the vma
from the rbtree in munmap(). Then it proceeds to teardown and free the
vma with only the read lock held.

This means that accesses to alloc->vma in binder_update_page_range() now
will race with vm_area_free() in munmap() and can cause a UAF as shown
in the following KASAN trace:

  ==================================================================
  BUG: KASAN: use-after-free in vm_insert_page+0x7c/0x1f0
  Read of size 8 at addr ffff16204ad00600 by task server/558

  CPU: 3 PID: 558 Comm: server Not tainted 5.10.150-00001-gdc8dcf942daa #1
  Hardware name: linux,dummy-virt (DT)
  Call trace:
   dump_backtrace+0x0/0x2a0
   show_stack+0x18/0x2c
   dump_stack+0xf8/0x164
   print_address_description.constprop.0+0x9c/0x538
   kasan_report+0x120/0x200
   __asan_load8+0xa0/0xc4
   vm_insert_page+0x7c/0x1f0
   binder_update_page_range+0x278/0x50c
   binder_alloc_new_buf+0x3f0/0xba0
   binder_transaction+0x64c/0x3040
   binder_thread_write+0x924/0x2020
   binder_ioctl+0x1610/0x2e5c
   __arm64_sys_ioctl+0xd4/0x120
   el0_svc_common.constprop.0+0xac/0x270
   do_el0_svc+0x38/0xa0
   el0_svc+0x1c/0x2c
   el0_sync_handler+0xe8/0x114
   el0_sync+0x180/0x1c0

  Allocated by task 559:
   kasan_save_stack+0x38/0x6c
   __kasan_kmalloc.constprop.0+0xe4/0xf0
   kasan_slab_alloc+0x18/0x2c
   kmem_cache_alloc+0x1b0/0x2d0
   vm_area_alloc+0x28/0x94
   mmap_region+0x378/0x920
   do_mmap+0x3f0/0x600
   vm_mmap_pgoff+0x150/0x17c
   ksys_mmap_pgoff+0x284/0x2dc
   __arm64_sys_mmap+0x84/0xa4
   el0_svc_common.constprop.0+0xac/0x270
   do_el0_svc+0x38/0xa0
   el0_svc+0x1c/0x2c
   el0_sync_handler+0xe8/0x114
   el0_sync+0x180/0x1c0

  Freed by task 560:
   kasan_save_stack+0x38/0x6c
   kasan_set_track+0x28/0x40
   kasan_set_free_info+0x24/0x4c
   __kasan_slab_free+0x100/0x164
   kasan_slab_free+0x14/0x20
   kmem_cache_free+0xc4/0x34c
   vm_area_free+0x1c/0x2c
   remove_vma+0x7c/0x94
   __do_munmap+0x358/0x710
   __vm_munmap+0xbc/0x130
   __arm64_sys_munmap+0x4c/0x64
   el0_svc_common.constprop.0+0xac/0x270
   do_el0_svc+0x38/0xa0
   el0_svc+0x1c/0x2c
   el0_sync_handler+0xe8/0x114
   el0_sync+0x180/0x1c0

  [...]
  ==================================================================

To prevent the race above, revert back to taking the mmap write lock
inside binder_update_page_range(). One might expect an increase of mmap
lock contention. However, binder already serializes these calls via top
level alloc->mutex. Also, there was no performance impact shown when
running the binder benchmark tests.

Fixes: c0fd2101781e ("Revert "android: binder: stop saving a pointer to the VMA"")
Fixes: dd2283f2605e ("mm: mmap: zap pages with read mmap_sem in munmap")
Reported-by: Jann Horn <jannh@google.com>
Closes: https://lore.kernel.org/all/20230518144052.xkj6vmddccq4v66b@revolver
Cc: <stable@vger.kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Yang Shi <yang.shi@linux.alibaba.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Acked-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20230519195950.1775656-1-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

binder: fix UAF caused by faulty buffer cleanup

commit bdc1c5fac982845a58d28690cdb56db8c88a530d upstream.

In binder_transaction_buffer_release() the 'failed_at' offset indicates
the number of objects to clean up. However, this function was changed by
commit 44d8047f1d87 ("binder: use standard functions to allocate fds"),
to release all the objects in the buffer when 'failed_at' is zero.

This introduced an issue when a transaction buffer is released without
any objects having been processed so far. In this case, 'failed_at' is
indeed zero yet it is misinterpreted as releasing the entire buffer.

This leads to use-after-free errors where nodes are incorrectly freed
and subsequently accessed. Such is the case in the following KASAN
report:

  ==================================================================
  BUG: KASAN: slab-use-after-free in binder_thread_read+0xc40/0x1f30
  Read of size 8 at addr ffff4faf037cfc58 by task poc/474

  CPU: 6 PID: 474 Comm: poc Not tainted 6.3.0-12570-g7df047b3f0aa #5
  Hardware name: linux,dummy-virt (DT)
  Call trace:
   dump_backtrace+0x94/0xec
   show_stack+0x18/0x24
   dump_stack_lvl+0x48/0x60
   print_report+0xf8/0x5b8
   kasan_report+0xb8/0xfc
   __asan_load8+0x9c/0xb8
   binder_thread_read+0xc40/0x1f30
   binder_ioctl+0xd9c/0x1768
   __arm64_sys_ioctl+0xd4/0x118
   invoke_syscall+0x60/0x188
  [...]

  Allocated by task 474:
   kasan_save_stack+0x3c/0x64
   kasan_set_track+0x2c/0x40
   kasan_save_alloc_info+0x24/0x34
   __kasan_kmalloc+0xb8/0xbc
   kmalloc_trace+0x48/0x5c
   binder_new_node+0x3c/0x3a4
   binder_transaction+0x2b58/0x36f0
   binder_thread_write+0x8e0/0x1b78
   binder_ioctl+0x14a0/0x1768
   __arm64_sys_ioctl+0xd4/0x118
   invoke_syscall+0x60/0x188
  [...]

  Freed by task 475:
   kasan_save_stack+0x3c/0x64
   kasan_set_track+0x2c/0x40
   kasan_save_free_info+0x38/0x5c
   __kasan_slab_free+0xe8/0x154
   __kmem_cache_free+0x128/0x2bc
   kfree+0x58/0x70
   binder_dec_node_tmpref+0x178/0x1fc
   binder_transaction_buffer_release+0x430/0x628
   binder_transaction+0x1954/0x36f0
   binder_thread_write+0x8e0/0x1b78
   binder_ioctl+0x14a0/0x1768
   __arm64_sys_ioctl+0xd4/0x118
   invoke_syscall+0x60/0x188
  [...]
  ==================================================================

In order to avoid these issues, let's always calculate the intended
'failed_at' offset beforehand. This is renamed and wrapped in a helper
function to make it clear and convenient.

Fixes: 32e9f56a96d8 ("binder: don't detect sender/target during buffer cleanup")
Reported-by: Zi Fan Tan <zifantan@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Acked-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20230505203020.4101154-1-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

binder: add lockless binder_alloc_(set|get)_vma()

commit 0fa53349c3acba0239369ba4cd133740a408d246 upstream.

Bring back the original lockless design in binder_alloc to determine
whether the buffer setup has been completed by the ->mmap() handler.
However, this time use smp_load_acquire() and smp_store_release() to
wrap all the ordering in a single macro call.

Also, add comments to make it evident that binder uses alloc->vma to
determine when the binder_alloc has been fully initialized. In these
scenarios acquiring the mmap_lock is not required.

Fixes: a43cfc87caaf ("android: binder: stop saving a pointer to the VMA")
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Link: https://lore.kernel.org/r/20230502201220.1756319-3-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "android: binder: stop saving a pointer to the VMA"

commit c0fd2101781ef761b636769b2f445351f71c3626 upstream.

This reverts commit a43cfc87caaf46710c8027a8c23b8a55f1078f19.

This patch fixed an issue reported by syzkaller in [1]. However, this
turned out to be only a band-aid in binder. The root cause, as bisected
by syzkaller, was fixed by commit 5789151e48ac ("mm/mmap: undo ->mmap()
when mas_preallocate() fails"). We no longer need the patch for binder.

Reverting such patch allows us to have a lockless access to alloc->vma
in specific cases where the mmap_lock is not required. This approach
avoids the contention that caused a performance regression.

[1] https://lore.kernel.org/all/0000000000004a0dbe05e1d749e0@google.com

[cmllamas: resolved conflicts with rework of alloc->mm and removal of
 binder_alloc_set_vma() also fixed comment section]

Fixes: a43cfc87caaf ("android: binder: stop saving a pointer to the VMA")
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Link: https://lore.kernel.org/r/20230502201220.1756319-2-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "binder_alloc: add missing mmap_lock calls when using the VMA"

commit b15655b12ddca7ade09807f790bafb6fab61b50a upstream.

This reverts commit 44e602b4e52f70f04620bbbf4fe46ecb40170bde.

This caused a performance regression particularly when pages are getting
reclaimed. We don't need to acquire the mmap_lock to determine when the
binder buffer has been fully initialized. A subsequent patch will bring
back the lockless approach for this.

[cmllamas: resolved trivial conflicts with renaming of alloc->mm]

Fixes: 44e602b4e52f ("binder_alloc: add missing mmap_lock calls when using the VMA")
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Link: https://lore.kernel.org/r/20230502201220.1756319-1-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amd/pm: Fix output of pp_od_clk_voltage

commit 40baba5693b9af586dc1063af603d05a79e57a6b upstream.

Printing the other clock types should not be conditioned on being able
to print OD_SCLK. Some GPUs currently have limited capability of only
printing a subset of these.

Since this condition was introduced in v5.18-rc1, reading from
`pp_od_clk_voltage` has been returning empty on the Asus ROG Strix G15
(2021).

Fixes: 79c65f3fcbb1 ("drm/amd/pm: do not expose power implementation details to amdgpu_pm.c")
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Jonatas Esteves <jntesteves@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amd/pm: add missing NotifyPowerSource message mapping for SMU13.0.7

commit 0d2dd02d74e6377268f56b90261de0fae8f0d2cb upstream.

Otherwise, the power source switching will fail due to message
unavailable.

Fixes: bf4823267a81 ("drm/amd/pm: fix possible power mode mismatch between driver and PMFW")
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/radeon: reintroduce radeon_dp_work_func content

commit a34fc1bcd2c4d8b09dcfc0b95ac65bca1e579bd7 upstream.

Put back the radeon_dp_work_func logic.  It seems that
handling DP RX interrupts is necessary to make some
panels work.  This was removed with the MST support,
but it regresses some systems so add it back.  While
we are here, add the proper mutex locking.

Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2567
Fixes: 01ad1d9c2888 ("drm/radeon: Drop legacy MST support")
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/mgag200: Fix gamma lut not initialized.

commit ad81e23426a651eb89a4b306e1c4169e6308c124 upstream.

When mgag200 switched from simple KMS to regular atomic helpers,
the initialization of the gamma settings was lost.
This leads to a black screen, if the bios/uefi doesn't use the same
pixel color depth.

v2: rebase on top of drm-misc-fixes, and add Cc stable tag.

Link: https://bugzilla.redhat.com/show_bug.cgi?id=2171155
Fixes: 1baf9127c482 ("drm/mgag200: Replace simple-KMS with regular atomic helpers")
Cc: <stable@vger.kernel.org>
Tested-by: Phil Oester <kernel@linuxace.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230510131034.284078-1-jfalempe@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-binding: cdns,usb3: Fix cdns,on-chip-buff-size type

commit 50a1726b148ff30778cb8a6cf3736130b07c93fd upstream.

In cdns3-gadget.c, 'cdns,on-chip-buff-size' was read using
device_property_read_u16(). It resulted in 0 if a 32bit value was used
in dts. This commit fixes the dt binding doc to declare it as u16.

Cc: stable@vger.kernel.org
Fixes: 68989fe1c39d ("dt-bindings: usb: Convert cdns-usb3.txt to YAML schema")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: use nofs when cleaning up aborted transactions

commit 597441b3436a43011f31ce71dc0a6c0bf5ce958a upstream.

Our CI system caught a lockdep splat:

  ======================================================
  WARNING: possible circular locking dependency detected
  6.3.0-rc7+ #1167 Not tainted
  ------------------------------------------------------
  kswapd0/46 is trying to acquire lock:
  ffff8c6543abd650 (sb_internal#2){++++}-{0:0}, at: btrfs_commit_inode_delayed_inode+0x5f/0x120

  but task is already holding lock:
  ffffffffabe61b40 (fs_reclaim){+.+.}-{0:0}, at: balance_pgdat+0x4aa/0x7a0

  which lock already depends on the new lock.

  the existing dependency chain (in reverse order) is:

  -> #1 (fs_reclaim){+.+.}-{0:0}:
 fs_reclaim_acquire+0xa5/0xe0
 kmem_cache_alloc+0x31/0x2c0
 alloc_extent_state+0x1d/0xd0
 __clear_extent_bit+0x2e0/0x4f0
 try_release_extent_mapping+0x216/0x280
 btrfs_release_folio+0x2e/0x90
 invalidate_inode_pages2_range+0x397/0x470
 btrfs_cleanup_dirty_bgs+0x9e/0x210
 btrfs_cleanup_one_transaction+0x22/0x760
 btrfs_commit_transaction+0x3b7/0x13a0
 create_subvol+0x59b/0x970
 btrfs_mksubvol+0x435/0x4f0
 __btrfs_ioctl_snap_create+0x11e/0x1b0
 btrfs_ioctl_snap_create_v2+0xbf/0x140
 btrfs_ioctl+0xa45/0x28f0
 __x64_sys_ioctl+0x88/0xc0
 do_syscall_64+0x38/0x90
 entry_SYSCALL_64_after_hwframe+0x72/0xdc

  -> #0 (sb_internal#2){++++}-{0:0}:
 __lock_acquire+0x1435/0x21a0
 lock_acquire+0xc2/0x2b0
 start_transaction+0x401/0x730
 btrfs_commit_inode_delayed_inode+0x5f/0x120
 btrfs_evict_inode+0x292/0x3d0
 evict+0xcc/0x1d0
 inode_lru_isolate+0x14d/0x1e0
 __list_lru_walk_one+0xbe/0x1c0
 list_lru_walk_one+0x58/0x80
 prune_icache_sb+0x39/0x60
 super_cache_scan+0x161/0x1f0
 do_shrink_slab+0x163/0x340
 shrink_slab+0x1d3/0x290
 shrink_node+0x300/0x720
 balance_pgdat+0x35c/0x7a0
 kswapd+0x205/0x410
 kthread+0xf0/0x120
 ret_from_fork+0x29/0x50

  other info that might help us debug this:

   Possible unsafe locking scenario:

 CPU0                    CPU1
 ----                    ----
    lock(fs_reclaim);
 lock(sb_internal#2);
 lock(fs_reclaim);
    lock(sb_internal#2);

   *** DEADLOCK ***

  3 locks held by kswapd0/46:
   #0: ffffffffabe61b40 (fs_reclaim){+.+.}-{0:0}, at: balance_pgdat+0x4aa/0x7a0
   #1: ffffffffabe50270 (shrinker_rwsem){++++}-{3:3}, at: shrink_slab+0x113/0x290
   #2: ffff8c6543abd0e0 (&type->s_umount_key#44){++++}-{3:3}, at: super_cache_scan+0x38/0x1f0

  stack backtrace:
  CPU: 0 PID: 46 Comm: kswapd0 Not tainted 6.3.0-rc7+ #1167
  Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014
  Call Trace:
   <TASK>
   dump_stack_lvl+0x58/0x90
   check_noncircular+0xd6/0x100
   ? save_trace+0x3f/0x310
   ? add_lock_to_list+0x97/0x120
   __lock_acquire+0x1435/0x21a0
   lock_acquire+0xc2/0x2b0
   ? btrfs_commit_inode_delayed_inode+0x5f/0x120
   start_transaction+0x401/0x730
   ? btrfs_commit_inode_delayed_inode+0x5f/0x120
   btrfs_commit_inode_delayed_inode+0x5f/0x120
   btrfs_evict_inode+0x292/0x3d0
   ? lock_release+0x134/0x270
   ? __pfx_wake_bit_function+0x10/0x10
   evict+0xcc/0x1d0
   inode_lru_isolate+0x14d/0x1e0
   __list_lru_walk_one+0xbe/0x1c0
   ? __pfx_inode_lru_isolate+0x10/0x10
   ? __pfx_inode_lru_isolate+0x10/0x10
   list_lru_walk_one+0x58/0x80
   prune_icache_sb+0x39/0x60
   super_cache_scan+0x161/0x1f0
   do_shrink_slab+0x163/0x340
   shrink_slab+0x1d3/0x290
   shrink_node+0x300/0x720
   balance_pgdat+0x35c/0x7a0
   kswapd+0x205/0x410
   ? __pfx_autoremove_wake_function+0x10/0x10
   ? __pfx_kswapd+0x10/0x10
   kthread+0xf0/0x120
   ? __pfx_kthread+0x10/0x10
   ret_from_fork+0x29/0x50
   </TASK>

This happens because when we abort the transaction in the transaction
commit path we call invalidate_inode_pages2_range on our block group
cache inodes (if we have space cache v1) and any delalloc inodes we may
have.  The plain invalidate_inode_pages2_range() call passes through
GFP_KERNEL, which makes sense in most cases, but not here.  Wrap these
two invalidate callees with memalloc_nofs_save/memalloc_nofs_restore to
make sure we don't end up with the fs reclaim dependency under the
transaction dependency.

CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gpio: mockup: Fix mode of debugfs files

commit 0a1bb16e0fe6650c3841e611de374bfd5578ad70 upstream.

This driver's debugfs files have had a read operation since commit
2a9e27408e12 ("gpio: mockup: rework debugfs interface"), but were
still being created with write-only mode bits.  Update them to
indicate that the files can also be read.

Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 2a9e27408e12 ("gpio: mockup: rework debugfs interface")
Cc: stable@kernel.org # v5.1+
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

parisc: Handle kprobes breakpoints only in kernel context

commit df419492e428b6a2bce98d0f613c58a13da6666c upstream.

The kernel kprobes break instructions should only be handled when running
in kernel context.

Cc: <stable@vger.kernel.org> # v5.18+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

parisc: Enable LOCKDEP support

commit adf8e96a7ea670d45b5de7594acc67e8f4787ae6 upstream.

Cc: <stable@vger.kernel.org> # v6.0+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

parisc: Allow to reboot machine after system halt

commit 2028315cf59bb899a5ac7e87dc48ecb8fac7ac24 upstream.

In case a machine can't power-off itself on system shutdown,
allow the user to reboot it by pressing the RETURN key.

Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

parisc: Fix flush_dcache_page() for usage from irq context

commit 61e150fb310729c98227a5edf6e4a3619edc3702 upstream.

Since at least kernel 6.1, flush_dcache_page() is called with IRQs
disabled, e.g. from aio_complete().

But the current implementation for flush_dcache_page() on parisc
unintentionally re-enables IRQs, which may lead to deadlocks.

Fix it by using xa_lock_irqsave() and xa_unlock_irqrestore()
for the flush_dcache_mmap_*lock() macros instead.

Cc: linux-parisc@vger.kernel.org
Cc: stable@kernel.org # 5.18+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>