Christian Marangi [Wed, 6 Jul 2022 22:53:18 +0000 (00:53 +0200)]
dt-bindings: clock: fix wrong clock documentation for qcom,rpmcc
qcom,rpmcc describe 2 different kind of device.
Currently we have definition for rpm-smd based device but we lack
Documentation for simple rpm based device.
Add the missing clk for ipq806x, apq8060, msm8660 and apq8064 and
provide additional example to describe these new simple rpm based
devices.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220706225321.26215-2-ansuelsmth@gmail.com
Bryan O'Donoghue [Tue, 12 Jul 2022 12:59:22 +0000 (13:59 +0100)]
clk: qcom: gcc-msm8939: Add missing USB HS system clock frequencies
The shipped qcom driver defines:
static struct clk_freq_tbl ftbl_gcc_usb_hs_system_clk[] = {
F(
57140000, gpll0_out_main, 14, 0, 0),
F(
80000000, gpll0_out_main, 10, 0, 0),
F(
100000000, gpll0_out_main, 8, 0, 0),
F_END
};
In the upstream code we omit 57.14 MHz and 100 MHz.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220712125922.3461675-7-bryan.odonoghue@linaro.org
Bryan O'Donoghue [Tue, 12 Jul 2022 12:59:21 +0000 (13:59 +0100)]
clk: qcom: gcc-msm8939: Add missing MDSS MDP clock frequencies
Again the msm8936/msm8939 supports a wider range of operating frequencies
to the antecedent msm8916 from which the msm8939.c driver is derived.
static struct clk_freq_tbl ftbl_gcc_mdss_mdp_clk[] = {
F(
50000000, gpll0_out_aux, 16, 0, 0),
F(
80000000, gpll0_out_aux, 10, 0, 0),
F(
100000000, gpll0_out_aux, 8, 0, 0),
F(
145500000, gpll0_out_aux, 5.5, 0, 0),
F(
153600000, gpll1_out_main, 4, 0, 0),
F(
160000000, gpll0_out_aux, 5, 0, 0),
F(
177780000, gpll0_out_aux, 4.5, 0, 0),
F(
200000000, gpll0_out_aux, 4, 0, 0),
F(
266670000, gpll0_out_aux, 3, 0, 0),
F(
307200000, gpll1_out_main, 2, 0, 0),
F(
366670000, gpll3_out_aux, 3, 0, 0),
F_END
};
We are missing 145.5 MHz and 153.6 MHz.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220712125922.3461675-6-bryan.odonoghue@linaro.org
Bryan O'Donoghue [Tue, 12 Jul 2022 12:59:20 +0000 (13:59 +0100)]
clk: qcom: gcc-msm8939: Add missing CAMSS CPP clock frequencies
Reviewing the qcom msm8936.c clock frequency tables we see
static struct clk_freq_tbl ftbl_gcc_camss_cpp_clk[] = {
F(
160000000, gpll0_out_main, 5, 0, 0),
F(
200000000, gpll0_out_main, 4, 0, 0),
F(
228570000, gpll0_out_main, 3.5, 0, 0),
F(
266670000, gpll0_out_main, 3, 0, 0),
F(
320000000, gpll0_out_main, 2.5, 0, 0),
F(
465000000, gpll2_out_main, 2, 0, 0),
F_END
};
which is a super-set of the msm8916 original definitions.
Add in the missing frequency definitions now.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220712125922.3461675-5-bryan.odonoghue@linaro.org
Bryan O'Donoghue [Tue, 12 Jul 2022 12:59:19 +0000 (13:59 +0100)]
clk: qcom: gcc-msm8939: Fix venus0_vcodec0_clk frequency definitions
The Venus clock frequencies are a copy/paste error from msm8916. Looking
at the original clock-gcc-8936.c ftbl_gcc_venus0_vcodec0_clk defines we
have:
- 133 MHz
- 200 MHz
- 266 MHz
These values are born out by the relevant qualcomm documentation for the
msm8936/msm8939 Venus core performance levels.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220712125922.3461675-4-bryan.odonoghue@linaro.org
Bryan O'Donoghue [Tue, 12 Jul 2022 12:59:18 +0000 (13:59 +0100)]
clk: qcom: gcc-msm8939: Add missing CAMSS CCI bus clock
Standard CCI bus clock clocks are 19.2 MHz and 37.5 MHz. We already define
the 19.2 MHz but are missing the 37.5 MHz.
See qcom kernel drivers/clk/qcom/clock-gcc-8936.c::ftbl_gcc_camss_cci_clk[]
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220712125922.3461675-3-bryan.odonoghue@linaro.org
Bryan O'Donoghue [Tue, 12 Jul 2022 12:59:17 +0000 (13:59 +0100)]
clk: qcom: gcc-msm8939: Fix weird field spacing in ftbl_gcc_camss_cci_clk
Adding a new item to this frequency table I see the existing indentation is
incorrect.
Fixes:
1664014e4679 ("clk: qcom: gcc-msm8939: Add MSM8939 Generic Clock Controller")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220712125922.3461675-2-bryan.odonoghue@linaro.org
Bjorn Andersson [Wed, 13 Jul 2022 21:28:18 +0000 (14:28 -0700)]
clk: qcom: gdsc: Bump parent usage count when GDSC is found enabled
When a GDSC is found to be enabled at boot the pm_runtime state will
be unbalanced as the GDSC is later turned off. Fix this by increasing
the usage counter on the power-domain, in line with how we handled the
regulator state.
Fixes:
1b771839de05 ("clk: qcom: gdsc: enable optional power domain support")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20220713212818.130277-1-bjorn.andersson@linaro.org
Abel Vesa [Wed, 13 Jul 2022 14:32:00 +0000 (17:32 +0300)]
clk: qcom: Drop mmcx gdsc supply for dispcc and videocc
Both dispcc and videocc use mmcx power domain now.
Lets drop the supply mmcx from every gdsc.
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes:
266e5cf39a0f ("arm64: dts: qcom: sm8250: remove mmcx regulator")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220713143200.3686765-1-abel.vesa@linaro.org
Ren Zhijie [Thu, 14 Jul 2022 12:11:44 +0000 (20:11 +0800)]
clk: qcom: fix build error initializer element is not constant
CONFIG_CC_VERSION_TEXT="x86_64-linux-gnu-gcc (Ubuntu 7.4.0-1ubuntu1~18.04.1) 7.4.0"
make ARCH=x86_64 CROSS_COMPILE=x86_64-linux-gnu-, will be failed, like this:
drivers/clk/qcom/gpucc-sm8350.c:111:2: error: initializer element is not constant
gpu_cc_parent,
^~~~~~~~~~~~~
drivers/clk/qcom/gpucc-sm8350.c:111:2: note: (near initialization for ‘gpu_cc_parent_data_0[0]’)
drivers/clk/qcom/gpucc-sm8350.c:126:2: error: initializer element is not constant
gpu_cc_parent,
^~~~~~~~~~~~~
drivers/clk/qcom/gpucc-sm8350.c:126:2: note: (near initialization for ‘gpu_cc_parent_data_1[0]’)
make[3]: *** [drivers/clk/qcom/gpucc-sm8350.o] Error 1
It seems that nested constant initializer is not supported in GCC 7.4.0. For portability resons, we should fix it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes:
160758b05ab1 ("clk: qcom: add support for SM8350 GPUCC")
Signed-off-by: Ren Zhijie <renzhijie2@huawei.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220714121144.71062-1-renzhijie2@huawei.com
Dmitry Baryshkov [Mon, 20 Jun 2022 07:19:33 +0000 (10:19 +0300)]
dt-bindings: clock: qcom,gcc-msm8996: add more GCC clock sources
Add additional GCC clock sources. This includes PCIe and USB PIPE and
UFS symbol clocks.
Fixes:
2a8aa18c1131 ("dt-bindings: clk: qcom: Fix self-validation, split, and clean cruft")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220620071936.1558906-2-dmitry.baryshkov@linaro.org
Jonathan Marek [Wed, 6 Jul 2022 15:43:36 +0000 (17:43 +0200)]
clk: qcom: add support for SM8350 DISPCC
Add support to the SM8350 display clock controller by extending the SM8250
display clock controller, which is almost identical but has some minor
differences.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220706154337.2026269-5-robert.foss@linaro.org
Robert Foss [Wed, 6 Jul 2022 15:43:34 +0000 (17:43 +0200)]
clk: qcom: add support for SM8350 GPUCC
The GPUCC manages the clocks for the Adreno GPU found on the
sm8350 SoCs.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220706154337.2026269-3-robert.foss@linaro.org
Bjorn Andersson [Wed, 6 Jul 2022 20:16:12 +0000 (15:16 -0500)]
Merge branch '
20220706154337.2026269-1-robert.foss@linaro.org' into clk-for-5.20
Vladimir Zapolskiy [Fri, 1 Jul 2022 06:27:44 +0000 (09:27 +0300)]
clk: qcom: add camera clock controller driver for SM8450 SoC
Add camera clock controller driver found on Qualcomm SM8450 SoC.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220701062744.2757931-1-vladimir.zapolskiy@linaro.org
Vladimir Zapolskiy [Fri, 1 Jul 2022 06:27:39 +0000 (09:27 +0300)]
clk: qcom: clk-alpha-pll: add Rivian EVO PLL configuration interfaces
Add and export Rivian EVO PLL configuration and control functions to
clock controller drivers, the PLL is used by SM8450 camera clock
controller.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220701062739.2757912-1-vladimir.zapolskiy@linaro.org
Vladimir Zapolskiy [Fri, 1 Jul 2022 06:27:29 +0000 (09:27 +0300)]
clk: qcom: clk-alpha-pll: add Lucid EVO PLL configuration interfaces
Add controls for Lucid EVO PLL configuration and export control functions
to clock controller drivers, the PLL is used by Qualcomm SM8450 camera
and display clock controllers.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220701062729.2757893-1-vladimir.zapolskiy@linaro.org
Vladimir Zapolskiy [Fri, 1 Jul 2022 06:27:20 +0000 (09:27 +0300)]
clk: qcom: clk-alpha-pll: limit exported symbols to GPL licensed code
Unify all exported PLL clock configuration functions and data structures
as GPL symbols.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220701062720.2757874-1-vladimir.zapolskiy@linaro.org
Vladimir Zapolskiy [Fri, 1 Jul 2022 06:27:11 +0000 (09:27 +0300)]
clk: qcom: clk-alpha-pll: fix clk_trion_pll_configure description
After merging lucid and trion pll functions in commit
0b01489475c6
("clk: qcom: clk-alpha-pll: same regs and ops for trion and lucid")
the function clk_trion_pll_configure() is left with an old description
header, which results in a W=2 compile time warning, fix it.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220701062711.2757855-1-vladimir.zapolskiy@linaro.org
Bjorn Andersson [Wed, 6 Jul 2022 20:20:51 +0000 (15:20 -0500)]
Merge branch '
20220701062622.2757831-2-vladimir.zapolskiy@linaro.org' into clk-for-5.20
Vladimir Zapolskiy [Fri, 1 Jul 2022 06:26:21 +0000 (09:26 +0300)]
dt-bindings: clock: add QCOM SM8450 camera clock bindings
The change adds device tree bindings for camera clock controller
found on SM8450 SoC.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220701062622.2757831-2-vladimir.zapolskiy@linaro.org
Jonathan Marek [Wed, 6 Jul 2022 15:43:35 +0000 (17:43 +0200)]
dt-bindings: clock: Add Qcom SM8350 DISPCC bindings
Add sm8350 DISPCC bindings, which are simply a symlink to the sm8250
bindings. Update the documentation with the new compatible.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220706154337.2026269-4-robert.foss@linaro.org
Robert Foss [Wed, 6 Jul 2022 15:43:33 +0000 (17:43 +0200)]
dt-bindings: clock: Add Qcom SM8350 GPUCC bindings
Add device tree bindings for graphics clock controller for
Qualcomm Technology Inc's SM8350 SoCs.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmityr.baryshkov@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220706154337.2026269-2-robert.foss@linaro.org
Dmitry Baryshkov [Sat, 21 May 2022 15:14:36 +0000 (18:14 +0300)]
clk: qcom: gcc-msm8960: create tsens device if there are no child nodes
Currently gcc-msm8960 driver manually creates tsens platform device
manually. It would be better to follow IPQ8064 approach, where tsens
device is defined as gcc's child device in the device tree. If nothing
else, it removes gcc's dependency on QFPROM, thus allowing clock
controller to be probed earlier.
Don't create it in case there are available child nodes (tsens) inside
the gcc's device tree node.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220521151437.1489111-4-dmitry.baryshkov@linaro.org
Dmitry Baryshkov [Sat, 21 May 2022 15:14:35 +0000 (18:14 +0300)]
dt-bindings: clock: qcom,gcc-apq8064: split tsens to the child node
Split tsens properties to the child node of the gcc. This follows the
lead of ipq8064 (which also uses a separate node for tsens) and makes
device tree closer to other platforms, where tsens is a completely
separate device.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220521151437.1489111-3-dmitry.baryshkov@linaro.org
Dmitry Baryshkov [Sat, 21 May 2022 15:14:34 +0000 (18:14 +0300)]
dt-bindings: clock: qcom,gcc-apq8064: move msm8960 compat from gcc-other.yaml
MSM8960 shares the design (and the driver) of the global clock
controller with APQ8064. Move it from clock/qcom,gcc-other.yaml to
clock/qcom,gcc-apq8064.yaml.
As the example in gcc-other.yaml was using qcom,gcc-msm8960 compat string,
change it to qcom,gcc-msm8974.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220521151437.1489111-2-dmitry.baryshkov@linaro.org
Nikita Travkin [Sun, 12 Jun 2022 14:59:55 +0000 (19:59 +0500)]
clk: qcom: gcc-msm8916: Add rates to the GP clocks
msm8916 has (at least) 6 "General Purpose" clocks that can be muxed to
SoC pins. These clocks are:
GP_CLK{0, 1} : GPIO_{31, 32} (Belongs to CAMSS according to Linux)
GP_CLK_{1-3}{A, B} : GPIO_{49-51, 97, 12, 13} (Belongs to GCC itself)
GP_MN : GPIO_110 (Doesn't seem to be described in gcc,
ignored in this patch)
Those clocks may be used as e.g. PWM sources for external peripherals.
Add more frequencies to the table for those clocks so it's possible
for arbitrary peripherals to make use of them.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220612145955.385787-5-nikita@trvn.ru
Nikita Travkin [Sun, 12 Jun 2022 14:59:53 +0000 (19:59 +0500)]
clk: qcom: clk-rcg2: Make sure to not write d=0 to the NMD register
Sometimes calculation of d value may result in 0 because of the
rounding after integer division. This causes the following error:
[ 113.969689] camss_gp1_clk_src: rcg didn't update its configuration.
[ 113.969754] WARNING: CPU: 3 PID: 35 at drivers/clk/qcom/clk-rcg2.c:122 update_config+0xc8/0xdc
Make sure that D value is never zero.
Fixes:
7f891faf596e ("clk: qcom: clk-rcg2: Add support for duty-cycle for RCG")
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220612145955.385787-3-nikita@trvn.ru
Nikita Travkin [Sun, 12 Jun 2022 14:59:52 +0000 (19:59 +0500)]
clk: qcom: clk-rcg2: Fail Duty-Cycle configuration if MND divider is not enabled.
In cases when MND is not enabled (e.g. when only Half Integer Divider is
used), setting D registers makes no effect.
Fail instead of making ineffective write.
Fixes:
7f891faf596e ("clk: qcom: clk-rcg2: Add support for duty-cycle for RCG")
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220612145955.385787-2-nikita@trvn.ru
Vladimir Zapolskiy [Thu, 19 May 2022 21:41:33 +0000 (00:41 +0300)]
clk: qcom: camcc-sm8250: Fix topology around titan_top power domain
On SM8250 two found VFE GDSC power domains shall not be operated, if
titan top is turned off, thus the former power domains will be set as
subdomains by a GDSC registration routine.
Fixes:
5d66ca79b58c ("clk: qcom: Add camera clock controller driver for SM8250")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220519214133.1728979-3-vladimir.zapolskiy@linaro.org
Vladimir Zapolskiy [Thu, 19 May 2022 21:41:32 +0000 (00:41 +0300)]
clk: qcom: camcc-sdm845: Fix topology around titan_top power domain
On SDM845 two found VFE GDSC power domains shall not be operated, if
titan top is turned off, thus the former power domains will be set as
subdomains by a GDSC registration routine.
Fixes:
78412c262004 ("clk: qcom: Add camera clock controller driver for SDM845")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220519214133.1728979-2-vladimir.zapolskiy@linaro.org
Robert Marko [Sun, 15 May 2022 21:00:47 +0000 (23:00 +0200)]
clk: qcom: ipq8074: dont disable gcc_sleep_clk_src
Once the usb sleep clocks are disabled, clock framework is trying to
disable the sleep clock source also.
However, it seems that it cannot be disabled and trying to do so produces:
[ 245.436390] ------------[ cut here ]------------
[ 245.441233] gcc_sleep_clk_src status stuck at 'on'
[ 245.441254] WARNING: CPU: 2 PID: 223 at clk_branch_wait+0x130/0x140
[ 245.450435] Modules linked in: xhci_plat_hcd xhci_hcd dwc3 dwc3_qcom leds_gpio
[ 245.456601] CPU: 2 PID: 223 Comm: sh Not tainted 5.18.0-rc4 #215
[ 245.463889] Hardware name: Xiaomi AX9000 (DT)
[ 245.470050] pstate:
204000c5 (nzCv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 245.474307] pc : clk_branch_wait+0x130/0x140
[ 245.481073] lr : clk_branch_wait+0x130/0x140
[ 245.485588] sp :
ffffffc009f2bad0
[ 245.489838] x29:
ffffffc009f2bad0 x28:
ffffff8003e6c800 x27:
0000000000000000
[ 245.493057] x26:
0000000000000000 x25:
0000000000000000 x24:
ffffff800226ef20
[ 245.500175] x23:
ffffffc0089ff550 x22:
0000000000000000 x21:
ffffffc008476ad0
[ 245.507294] x20:
0000000000000000 x19:
ffffffc00965ac70 x18:
fffffffffffc51a7
[ 245.514413] x17:
68702e3030303837 x16:
3a6d726f6674616c x15:
ffffffc089f2b777
[ 245.521531] x14:
ffffffc0095c9d18 x13:
0000000000000129 x12:
0000000000000129
[ 245.528649] x11:
00000000ffffffea x10:
ffffffc009621d18 x9 :
0000000000000001
[ 245.535767] x8 :
0000000000000001 x7 :
0000000000017fe8 x6 :
0000000000000001
[ 245.542885] x5 :
ffffff803fdca6d8 x4 :
0000000000000000 x3 :
0000000000000027
[ 245.550002] x2 :
0000000000000027 x1 :
0000000000000023 x0 :
0000000000000026
[ 245.557122] Call trace:
[ 245.564229] clk_branch_wait+0x130/0x140
[ 245.566490] clk_branch2_disable+0x2c/0x40
[ 245.570656] clk_core_disable+0x60/0xb0
[ 245.574561] clk_core_disable+0x68/0xb0
[ 245.578293] clk_disable+0x30/0x50
[ 245.582113] dwc3_qcom_remove+0x60/0xc0 [dwc3_qcom]
[ 245.585588] platform_remove+0x28/0x60
[ 245.590361] device_remove+0x4c/0x80
[ 245.594179] device_release_driver_internal+0x1dc/0x230
[ 245.597914] device_driver_detach+0x18/0x30
[ 245.602861] unbind_store+0xec/0x110
[ 245.607027] drv_attr_store+0x24/0x40
[ 245.610847] sysfs_kf_write+0x44/0x60
[ 245.614405] kernfs_fop_write_iter+0x128/0x1c0
[ 245.618052] new_sync_write+0xc0/0x130
[ 245.622391] vfs_write+0x1d4/0x2a0
[ 245.626123] ksys_write+0x58/0xe0
[ 245.629508] __arm64_sys_write+0x1c/0x30
[ 245.632895] invoke_syscall.constprop.0+0x5c/0x110
[ 245.636890] do_el0_svc+0xa0/0x150
[ 245.641488] el0_svc+0x18/0x60
[ 245.644872] el0t_64_sync_handler+0xa4/0x130
[ 245.647914] el0t_64_sync+0x174/0x178
[ 245.652340] ---[ end trace
0000000000000000 ]---
So, add CLK_IS_CRITICAL flag to the clock so that the kernel won't try
to disable the sleep clock.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220515210048.483898-10-robimarko@gmail.com
Robert Marko [Sun, 15 May 2022 21:00:46 +0000 (23:00 +0200)]
clk: qcom: ipq8074: add USB GDSCs
Add GDSC-s for each of the two USB controllers built-in the IPQ8074.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220515210048.483898-9-robimarko@gmail.com
Bjorn Andersson [Thu, 30 Jun 2022 23:24:35 +0000 (18:24 -0500)]
Merge branch '
20220515210048.483898-8-robimarko@gmail.com' into clk-for-5.20
Robert Marko [Sun, 15 May 2022 21:00:45 +0000 (23:00 +0200)]
dt-bindings: clock: qcom: ipq8074: add USB GDSCs
Add bindings for the USB GDSCs found in IPQ8074 GCC.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220515210048.483898-8-robimarko@gmail.com
Robert Marko [Sun, 15 May 2022 21:00:44 +0000 (23:00 +0200)]
dt-bindings: clocks: qcom,gcc-ipq8074: support power domains
GCC inside of IPQ8074 also provides power management via built-in GDSCs.
In order to do so, '#power-domain-cells' must be set to 1.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220515210048.483898-7-robimarko@gmail.com
Robert Marko [Sun, 15 May 2022 21:00:43 +0000 (23:00 +0200)]
clk: qcom: ipq8074: set BRANCH_HALT_DELAY flag for UBI clocks
Currently, attempting to enable the UBI clocks will cause the stuck at
off warning to be printed and clk_enable will fail.
[ 14.936694] gcc_ubi1_ahb_clk status stuck at 'off'
Downstream 5.4 QCA kernel has fixed this by seting the BRANCH_HALT_DELAY
flag on UBI clocks, so lets do the same.
Fixes:
5736294aef83 ("clk: qcom: ipq8074: add NSS clocks")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220515210048.483898-6-robimarko@gmail.com
Robert Marko [Sun, 15 May 2022 21:00:42 +0000 (23:00 +0200)]
clk: qcom: ipq8074: add PPE crypto clock
The built-in PPE engine has a dedicated clock for the EIP-197 crypto
engine.
So, since the required clock currently missing add support for it.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220515210048.483898-5-robimarko@gmail.com
Robert Marko [Sun, 15 May 2022 21:00:41 +0000 (23:00 +0200)]
dt-bindings: clock: qcom: ipq8074: add PPE crypto clock
Add binding for the PPE crypto clock in IPQ8074.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220515210048.483898-4-robimarko@gmail.com
Robert Marko [Sun, 15 May 2022 21:00:40 +0000 (23:00 +0200)]
clk: qcom: ipq8074: fix NSS port frequency tables
NSS port 5 and 6 frequency tables are currently broken and are causing a
wide ranges of issue like 1G not working at all on port 6 or port 5 being
clocked with 312 instead of 125 MHz as UNIPHY1 gets selected.
So, update the frequency tables with the ones from the downstream QCA 5.4
based kernel which has already fixed this.
Fixes:
7117a51ed303 ("clk: qcom: ipq8074: add NSS ethernet port clocks")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220515210048.483898-3-robimarko@gmail.com
Robert Marko [Sun, 15 May 2022 21:00:39 +0000 (23:00 +0200)]
clk: qcom: ipq8074: SW workaround for UBI32 PLL lock
UBI32 Huayra PLL fails to lock in 5 us in some SoC silicon and thus it
will cause the wait_for_pll() to timeout and thus return the error
indicating that the PLL failed to lock.
This is bug in Huayra PLL HW for which SW workaround
is to set bit 26 of TEST_CTL register.
This is ported from the QCA 5.4 based downstream kernel.
Fixes:
b8e7e519625f ("clk: qcom: ipq8074: add remaining PLL’s")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220515210048.483898-2-robimarko@gmail.com
Robert Marko [Sun, 15 May 2022 21:00:38 +0000 (23:00 +0200)]
clk: qcom: ipq8074: fix NSS core PLL-s
Like in IPQ6018 the NSS related Alpha PLL-s require initial configuration
to work.
So, obtain the regmap that is required for the Alpha PLL configuration
and thus utilize the qcom_cc_really_probe() as we already have the regmap.
Then utilize the Alpha PLL configs from the downstream QCA 5.4 based
kernel to configure them.
This fixes the UBI32 and NSS crypto PLL-s failing to get enabled by the
kernel.
Fixes:
b8e7e519625f ("clk: qcom: ipq8074: add remaining PLL’s")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220515210048.483898-1-robimarko@gmail.com
Bryan O'Donoghue [Wed, 4 May 2022 16:38:35 +0000 (17:38 +0100)]
clk: qcom: gcc-msm8939: Point MM peripherals to system_mm_noc clock
Qcom docs indciate the following peripherals operating from System NOC
MM not from System NOC clocks.
- MDP
- VFE
- JPEGe
- Venus
Switch over the relevant parent pointers.
Fixes:
1664014e4679 ("clk: qcom: gcc-msm8939: Add MSM8939 Generic Clock Controller")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220504163835.40130-5-bryan.odonoghue@linaro.org
Bryan O'Donoghue [Wed, 4 May 2022 16:38:34 +0000 (17:38 +0100)]
clk: qcom: gcc-msm8939: Add missing system_mm_noc_bfdcd_clk_src
The msm8939 has an additional higher operating point for the multi-media
peripherals. The higher throughput MM componets operate off of the
system-mm noc not the system noc.
system_mm_noc_bfdcd_clk_src is the source clock for the higher frequency
capable system noc mm.
Maximum frequency for the MM SNOC is 400 MHz.
Fixes:
1664014e4679 ("clk: qcom: gcc-msm8939: Add MSM8939 Generic Clock Controller")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220504163835.40130-4-bryan.odonoghue@linaro.org
Bryan O'Donoghue [Wed, 4 May 2022 16:38:33 +0000 (17:38 +0100)]
clk: qcom: gcc-msm8939: Fix bimc_ddr_clk_src rcgr base address
Reviewing qcom docs for the 8939 we can see the command rcgr is pointing to
the wrong address. bimc_ddr_clk_src_rcgr is @ 0x01832024 not 0x01832004.
Fixes:
1664014e4679 ("clk: qcom: gcc-msm8939: Add MSM8939 Generic Clock Controller")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220504163835.40130-3-bryan.odonoghue@linaro.org
Bryan O'Donoghue [Wed, 4 May 2022 16:38:32 +0000 (17:38 +0100)]
clk: qcom: gcc-msm8939: Add missing SYSTEM_MM_NOC_BFDCD_CLK_SRC
When adding in the indexes for this clock-controller we missed
SYSTEM_MM_NOC_BFDCD_CLK_SRC.
Add it in now.
Fixes:
4c71d6abc4fc ("clk: qcom: Add DT bindings for MSM8939 GCC")
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220504163835.40130-2-bryan.odonoghue@linaro.org
Johan Hovold [Tue, 28 Jun 2022 08:57:07 +0000 (10:57 +0200)]
clk: qcom: gcc-sc8280xp: use phy-mux clock for PCIe
Use the new phy-mux clock implementation for the PCIe pipe clock muxes
so that the pipe clock source is set to the QMP PHY PLL when the
downstream pipe clock is enabled and restored to the always-on XO when
it is again disabled.
This is needed to prevent the corresponding GDSC from hanging when
enabling or disabling the PCIe power domain, something which requires a
ticking source.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220628085707.16214-1-johan+linaro@kernel.org
Krzysztof Kozlowski [Fri, 13 May 2022 06:13:41 +0000 (08:13 +0200)]
dt-bindings: clock: qcom,gcc-sdm845: add parent power domain
Allow Qualcomm GCC to register its parent power domain (e.g. RPMHPD) to
properly pass performance state from children.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220513061347.46480-2-krzysztof.kozlowski@linaro.org
Ansuel Smith [Sat, 30 Apr 2022 05:44:58 +0000 (07:44 +0200)]
clk: qcom: clk-krait: add apq/ipq8064 errata workaround
Add apq/ipq8064 errata workaround where the sec_src clock gating needs to
be disabled during switching. krait-cc compatible is not enough to
handle this and limit this workaround to apq/ipq8064. We check machine
compatible to handle this.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430054458.31321-4-ansuelsmth@gmail.com
Ansuel Smith [Sat, 30 Apr 2022 05:44:57 +0000 (07:44 +0200)]
clk: qcom: clk-krait: unlock spin after mux completion
Unlock spinlock after the mux switch is completed to prevent any corner
case of mux request while the switch still needs to be done.
Fixes:
4d7dc77babfe ("clk: qcom: Add support for Krait clocks")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430054458.31321-3-ansuelsmth@gmail.com
Ansuel Smith [Sat, 30 Apr 2022 05:44:56 +0000 (07:44 +0200)]
clk: qcom: clk-hfpll: use poll_timeout macro
Use regmap_read_poll_timeout macro instead of do-while structure to tidy
things up. Also set a timeout to prevent any sort of system stall.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430054458.31321-2-ansuelsmth@gmail.com
Li kunyu [Mon, 27 Jun 2022 02:05:00 +0000 (10:05 +0800)]
clk: qcom: gcc-sm6350: Drop extra semicolon
Drop the extra semicolon after qcom_cc_really_probe()
Signed-off-by: Li kunyu <kunyu@nfschina.com>
[bjorn: Rewrote commit message]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220627020500.135125-1-kunyu@nfschina.com
Johan Hovold [Fri, 20 May 2022 10:09:48 +0000 (12:09 +0200)]
clk: qcom: gcc-sc8280xp: use collapse-voting for PCIe GDSCs
The PCIe GDSCs can be shared with other masters and should use the APCS
collapse-vote register when updating the power state.
This is specifically also needed to be able to disable power domains
that have been enabled by boot firmware using the vote register.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220520100948.19622-4-johan+linaro@kernel.org
Johan Hovold [Fri, 20 May 2022 10:09:47 +0000 (12:09 +0200)]
clk: qcom: gdsc: add support for collapse-vote registers
Recent Qualcomm platforms have APCS collapse-vote registers that allow
for sharing GDSCs with other masters (e.g. LPASS).
Add support for using such vote registers instead of the control
register when updating the GDSC power state.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220520100948.19622-3-johan+linaro@kernel.org
Johan Hovold [Fri, 20 May 2022 10:09:46 +0000 (12:09 +0200)]
clk: qcom: gdsc: add collapse-bit helper
Add a helper for updating the SW_COLLAPSE bit during initialisation and
state updates.
Note that the update during initialisation was relying on the
SW_COLLAPSE bit not having been set earlier rather than passing in zero
explicitly to clear the collapse vote.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220520100948.19622-2-johan+linaro@kernel.org
Vladimir Zapolskiy [Wed, 18 May 2022 10:35:54 +0000 (13:35 +0300)]
clk: qcom: camcc-sm8250: Fix halt on boot by reducing driver's init level
Access to I/O of SM8250 camera clock controller IP depends on enabled
GCC_CAMERA_AHB_CLK clock supplied by global clock controller, the latter
one is inited on subsys level, so, to satisfy the dependency, it would
make sense to deprive the init level of camcc-sm8250 driver.
If both drivers are compiled as built-in, there is a change that a board
won't boot up due to a race, which happens on the same init level.
Fixes:
5d66ca79b58c ("clk: qcom: Add camera clock controller driver for SM8250")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220518103554.949511-1-vladimir.zapolskiy@linaro.org
Bjorn Andersson [Sun, 26 Jun 2022 02:38:04 +0000 (21:38 -0500)]
Merge tag '
20220608105238.2973600-1-dmitry.baryshkov@linaro.org' into clk-for-5.20
v5.19-rc1 +
20220608105238.2973600-2-dmitry.baryshkov@linaro.org +
20220608105238.2973600-3-dmitry.baryshkov@linaro.org +
20220608105238.2973600-4-dmitry.baryshkov@linaro.org
Dmitry Baryshkov [Wed, 8 Jun 2022 10:52:36 +0000 (13:52 +0300)]
clk: qcom: gcc-sc7280: use new clk_regmap_phy_mux_ops for PCIe pipe clocks
Use newly defined clk_regmap_phy_mux_ops for PCIe pipe clocks to let
the clock framework automatically park the clock when the clock is
switched off and restore the parent when the clock is switched on.
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220608105238.2973600-4-dmitry.baryshkov@linaro.org
Dmitry Baryshkov [Wed, 8 Jun 2022 10:52:35 +0000 (13:52 +0300)]
clk: qcom: gcc-sm8450: use new clk_regmap_phy_mux_ops for PCIe pipe clocks
Use newly defined clk_regmap_phy_mux_ops for PCIe pipe clocks to let
the clock framework automatically park the clock when the clock is
switched off and restore the parent when the clock is switched on.
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220608105238.2973600-3-dmitry.baryshkov@linaro.org
Dmitry Baryshkov [Wed, 8 Jun 2022 10:52:34 +0000 (13:52 +0300)]
clk: qcom: regmap: add PHY clock source implementation
On recent Qualcomm platforms the QMP PIPE clocks feed into a set of
muxes which must be parked to the "safe" source (bi_tcxo) when
corresponding GDSC is turned off and on again. Currently this is
handcoded in the PCIe driver by reparenting the gcc_pipe_N_clk_src
clock. However the same code sequence should be applied in the
pcie-qcom endpoint, USB3 and UFS drivers.
Rather than copying this sequence over and over again, follow the
example of clk_rcg2_shared_ops and implement this parking in the
enable() and disable() clock operations. Supplement the regmap-mux with
the new clk_regmap_phy_mux type, which implements such multiplexers
as a simple gate clocks.
This is possible since each of these multiplexers has just two clock
sources: one coming from the PHY and a reference (XO) one. If the clock
is running off the from-PHY source, report it as enabled. Report it as
disabled otherwise (if it uses reference source).
This way the PHY will disable the pipe clock before turning off the
GDSC, which in turn would lead to disabling corresponding pipe_clk_src
(and thus it being parked to a safe, reference clock source). And vice
versa, after enabling the GDSC the PHY will enable the pipe clock, which
would cause pipe_clk_src to be switched from a safe source to the
working one.
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220608105238.2973600-2-dmitry.baryshkov@linaro.org
Dmitry Baryshkov [Fri, 17 Jun 2022 12:29:21 +0000 (15:29 +0300)]
clk: qcom: mmcc-msm8996: use parent_hws/_data instead of parent_names
Convert the clock driver to specify parent data rather than parent
names, to actually bind using 'clock-names' specified in the DTS rather
than global clock names. Use parent_hws where possible to refer parent
clocks directly, skipping the lookup.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220617122922.769562-6-dmitry.baryshkov@linaro.org
Dmitry Baryshkov [Fri, 17 Jun 2022 12:29:20 +0000 (15:29 +0300)]
clk: qcom: mmcc-msm8996: move clock parent tables down
Move clock parent tables down, after the MMPLL declrataions, so that we
can use gpll hw clock fields in the next commit.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220617122922.769562-5-dmitry.baryshkov@linaro.org
Dmitry Baryshkov [Fri, 17 Jun 2022 12:29:19 +0000 (15:29 +0300)]
clk: qcom: mmcc-msm8996: use ARRAY_SIZE instead of specifying num_parents
Use ARRAY_SIZE() instead of manually specifying num_parents. This makes
adding/removing entries to/from parent_data easy and errorproof.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220617122922.769562-4-dmitry.baryshkov@linaro.org
Stephen Boyd [Tue, 17 May 2022 19:09:49 +0000 (12:09 -0700)]
clk: qcom: rpmh: Add note about sleep/wake state for BCMs
The sleep/wake state doesn't need to be set here because of specific
RPMh behavior that carries over the active state when sleep/wake state
hasn't been modified. Add a note to the code so we aren't tempted to set
the sleep/wake states.
Cc: Alex Elder <elder@linaro.org>
Cc: Taniya Das <quic_tdas@quicinc.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220517190949.2922197-1-swboyd@chromium.org
Linus Torvalds [Mon, 6 Jun 2022 00:18:54 +0000 (17:18 -0700)]
Linux 5.19-rc1
Linus Torvalds [Mon, 6 Jun 2022 00:14:03 +0000 (17:14 -0700)]
Merge tag 'pull-work.fd-fixes' of git://git./linux/kernel/git/viro/vfs
Pull file descriptor fix from Al Viro:
"Fix for breakage in #work.fd this window"
* tag 'pull-work.fd-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix the breakage in close_fd_get_file() calling conventions change
Linus Torvalds [Mon, 6 Jun 2022 00:05:38 +0000 (17:05 -0700)]
Merge tag 'mm-hotfixes-stable-2022-06-05' of git://git./linux/kernel/git/akpm/mm
Pull mm hotfixes from Andrew Morton:
"Fixups for various recently-added and longer-term issues and a few
minor tweaks:
- fixes for material merged during this merge window
- cc:stable fixes for more longstanding issues
- minor mailmap and MAINTAINERS updates"
* tag 'mm-hotfixes-stable-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/oom_kill.c: fix vm_oom_kill_table[] ifdeffery
x86/kexec: fix memory leak of elf header buffer
mm/memremap: fix missing call to untrack_pfn() in pagemap_range()
mm: page_isolation: use compound_nr() correctly in isolate_single_pageblock()
mm: hugetlb_vmemmap: fix CONFIG_HUGETLB_PAGE_FREE_VMEMMAP_DEFAULT_ON
MAINTAINERS: add maintainer information for z3fold
mailmap: update Josh Poimboeuf's email
Linus Torvalds [Sun, 5 Jun 2022 23:58:27 +0000 (16:58 -0700)]
Merge tag 'mm-nonmm-stable-2022-06-05' of git://git./linux/kernel/git/akpm/mm
Pull delay-accounting update from Andrew Morton:
"A single featurette for delay accounting.
Delayed a bit because, unusually, it had dependencies on both the
mm-stable and mm-nonmm-stable queues"
* tag 'mm-nonmm-stable-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
delayacct: track delays from write-protect copy
Linus Torvalds [Sun, 5 Jun 2022 18:51:48 +0000 (11:51 -0700)]
bluetooth: don't use bitmaps for random flag accesses
The bluetooth code uses our bitmap infrastructure for the two bits (!)
of connection setup flags, and in the process causes odd problems when
it converts between a bitmap and just the regular values of said bits.
It's completely pointless to do things like bitmap_to_arr32() to convert
a bitmap into a u32. It shoudln't have been a bitmap in the first
place. The reason to use bitmaps is if you have arbitrary number of
bits you want to manage (not two!), or if you rely on the atomicity
guarantees of the bitmap setting and clearing.
The code could use an "atomic_t" and use "atomic_or/andnot()" to set and
clear the bit values, but considering that it then copies the bitmaps
around with "bitmap_to_arr32()" and friends, there clearly cannot be a
lot of atomicity requirements.
So just use a regular integer.
In the process, this avoids the warnings about erroneous use of
bitmap_from_u64() which were triggered on 32-bit architectures when
conversion from a u64 would access two words (and, surprise, surprise,
only one word is needed - and indeed overkill - for a 2-bit bitmap).
That was always problematic, but the compiler seems to notice it and
warn about the invalid pattern only after commit
0a97953fd221 ("lib: add
bitmap_{from,to}_arr64") changed the exact implementation details of
'bitmap_from_u64()', as reported by Sudip Mukherjee and Stephen Rothwell.
Fixes:
fe92ee6425a2 ("Bluetooth: hci_core: Rework hci_conn_params flags")
Link: https://lore.kernel.org/all/YpyJ9qTNHJzz0FHY@debian/
Link: https://lore.kernel.org/all/20220606080631.0c3014f2@canb.auug.org.au/
Link: https://lore.kernel.org/all/20220605162537.1604762-1-yury.norov@gmail.com/
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sun, 5 Jun 2022 18:01:42 +0000 (14:01 -0400)]
fix the breakage in close_fd_get_file() calling conventions change
It used to grab an extra reference to struct file rather than
just transferring to caller the one it had removed from descriptor
table. New variant doesn't, and callers need to be adjusted.
Reported-and-tested-by: syzbot+47dd250f527cb7bebf24@syzkaller.appspotmail.com
Fixes:
6319194ec57b ("Unify the primitives for file descriptor closing")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Sun, 5 Jun 2022 18:00:43 +0000 (11:00 -0700)]
Merge tag 'x86-urgent-2022-06-05' of git://git./linux/kernel/git/tip/tip
Pull x86 SGX fix from Thomas Gleixner:
"A single fix for x86/SGX to prevent that memory which is allocated for
an SGX enclave is accounted to the wrong memory control group"
* tag 'x86-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/sgx: Set active memcg prior to shmem allocation
Linus Torvalds [Sun, 5 Jun 2022 17:57:35 +0000 (10:57 -0700)]
Merge tag 'x86-mm-2022-06-05' of git://git./linux/kernel/git/tip/tip
Pull x86 mm cleanup from Thomas Gleixner:
"Use PAGE_ALIGNED() instead of open coding it in the x86/mm code"
* tag 'x86-mm-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Use PAGE_ALIGNED(x) instead of IS_ALIGNED(x, PAGE_SIZE)
Linus Torvalds [Sun, 5 Jun 2022 17:55:23 +0000 (10:55 -0700)]
Merge tag 'x86-microcode-2022-06-05' of git://git./linux/kernel/git/tip/tip
Pull x86 microcode updates from Thomas Gleixner:
- Disable late microcode loading by default. Unless the HW people get
their act together and provide a required minimum version in the
microcode header for making a halfways informed decision its just
lottery and broken.
- Warn and taint the kernel when microcode is loaded late
- Remove the old unused microcode loader interface
- Remove a redundant perf callback from the microcode loader
* tag 'x86-microcode-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode: Remove unnecessary perf callback
x86/microcode: Taint and warn on late loading
x86/microcode: Default-disable late loading
x86/microcode: Rip out the OLD_INTERFACE
Linus Torvalds [Sun, 5 Jun 2022 17:53:41 +0000 (10:53 -0700)]
Merge tag 'x86-cleanups-2022-06-05' of git://git./linux/kernel/git/tip/tip
Pull x86 cleanups from Thomas Gleixner:
"A set of small x86 cleanups:
- Remove unused headers in the IDT code
- Kconfig indendation and comment fixes
- Fix all 'the the' typos in one go instead of waiting for bots to
fix one at a time"
* tag 'x86-cleanups-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Fix all occurences of the "the the" typo
x86/idt: Remove unused headers
x86/Kconfig: Fix indentation of arch/x86/Kconfig.debug
x86/Kconfig: Fix indentation and add endif comments to arch/x86/Kconfig
Linus Torvalds [Sun, 5 Jun 2022 17:49:42 +0000 (10:49 -0700)]
Merge tag 'x86-boot-2022-06-05' of git://git./linux/kernel/git/tip/tip
Pull x86 boot update from Thomas Gleixner:
"Use strlcpy() instead of strscpy() in arch_setup()"
* tag 'x86-boot-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/setup: Use strscpy() to replace deprecated strlcpy()
Linus Torvalds [Sun, 5 Jun 2022 17:47:06 +0000 (10:47 -0700)]
Merge tag 'timers-core-2022-06-05' of git://git./linux/kernel/git/tip/tip
Pull clockevent/clocksource updates from Thomas Gleixner:
- Device tree bindings for MT8186
- Tell the kernel that the RISC-V SBI timer stops in deeper power
states
- Make device tree parsing in sp804 more robust
- Dead code removal and tiny fixes here and there
- Add the missing SPDX identifiers
* tag 'timers-core-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/oxnas-rps: Fix irq_of_parse_and_map() return value
clocksource/drivers/timer-ti-dm: Remove unnecessary NULL check
clocksource/drivers/timer-sun5i: Convert to SPDX identifier
clocksource/drivers/timer-sun4i: Convert to SPDX identifier
clocksource/drivers/pistachio: Convert to SPDX identifier
clocksource/drivers/orion: Convert to SPDX identifier
clocksource/drivers/lpc32xx: Convert to SPDX identifier
clocksource/drivers/digicolor: Convert to SPDX identifier
clocksource/drivers/armada-370-xp: Convert to SPDX identifier
clocksource/drivers/mips-gic-timer: Convert to SPDX identifier
clocksource/drivers/jcore: Convert to SPDX identifier
clocksource/drivers/bcm_kona: Convert to SPDX identifier
clocksource/drivers/sp804: Avoid error on multiple instances
clocksource/drivers/riscv: Events are stopped during CPU suspend
clocksource/drivers/ixp4xx: Drop boardfile probe path
dt-bindings: timer: Add compatible for Mediatek MT8186
Linus Torvalds [Sun, 5 Jun 2022 17:42:40 +0000 (10:42 -0700)]
Merge tag 'sched-urgent-2022-06-05' of git://git./linux/kernel/git/tip/tip
Pull scheduler fix from Thomas Gleixner:
"Fix the fallout of sysctl code move which placed the init function
wrong"
* tag 'sched-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/autogroup: Fix sysctl move
Linus Torvalds [Sun, 5 Jun 2022 17:40:31 +0000 (10:40 -0700)]
Merge tag 'perf-urgent-2022-06-05' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
- Make the ICL event constraints match reality
- Remove a unused local variable
* tag 'perf-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Remove unused local variable
perf/x86/intel: Fix event constraints for ICL
Linus Torvalds [Sun, 5 Jun 2022 17:39:20 +0000 (10:39 -0700)]
Merge tag 'perf-core-2022-06-05' of git://git./linux/kernel/git/tip/tip
Pull perf fixlet from Thomas Gleixner:
"Trivial indentation fix in Kconfig"
* tag 'perf-core-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/Kconfig: Fix indentation in the Kconfig file
Linus Torvalds [Sun, 5 Jun 2022 16:45:27 +0000 (09:45 -0700)]
Merge tag 'objtool-urgent-2022-06-05' of git://git./linux/kernel/git/tip/tip
Pull objtool fixes from Thomas Gleixner:
- Handle __ubsan_handle_builtin_unreachable() correctly and treat it as
noreturn
- Allow architectures to select uaccess validation
- Use the non-instrumented bit test for test_cpu_has() to prevent
escape from non-instrumentable regions
- Use arch_ prefixed atomics for JUMP_LABEL=n builds to prevent escape
from non-instrumentable regions
- Mark a few tiny inline as __always_inline to prevent GCC from
bringing them out of line and instrumenting them
- Mark the empty stub context_tracking_enabled() as always inline as
GCC brings them out of line and instruments the empty shell
- Annotate ex_handler_msr_mce() as dead end
* tag 'objtool-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/extable: Annotate ex_handler_msr_mce() as a dead end
context_tracking: Always inline empty stubs
x86: Always inline on_thread_stack() and current_top_of_stack()
jump_label,noinstr: Avoid instrumentation for JUMP_LABEL=n builds
x86/cpu: Elide KCSAN for cpu_has() and friends
objtool: Mark __ubsan_handle_builtin_unreachable() as noreturn
objtool: Add CONFIG_HAVE_UACCESS_VALIDATION
Linus Torvalds [Sun, 5 Jun 2022 16:25:12 +0000 (09:25 -0700)]
Merge tag 'scsi-misc' of git://git./linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"Mostly small bug fixes plus other trivial updates.
The major change of note is moving ufs out of scsi and a minor update
to lpfc vmid handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: qla2xxx: Remove unused 'ql_dm_tgt_ex_pct' parameter
scsi: qla2xxx: Remove setting of 'req' and 'rsp' parameters
scsi: mpi3mr: Fix kernel-doc
scsi: lpfc: Add support for ATTO Fibre Channel devices
scsi: core: Return BLK_STS_TRANSPORT for ALUA transitioning
scsi: sd_zbc: Prevent zone information memory leak
scsi: sd: Fix potential NULL pointer dereference
scsi: mpi3mr: Rework mrioc->bsg_device model to fix warnings
scsi: myrb: Fix up null pointer access on myrb_cleanup()
scsi: core: Unexport scsi_bus_type
scsi: sd: Don't call blk_cleanup_disk() in sd_probe()
scsi: ufs: ufshcd: Delete unnecessary NULL check
scsi: isci: Fix typo in comment
scsi: pmcraid: Fix typo in comment
scsi: smartpqi: Fix typo in comment
scsi: qedf: Fix typo in comment
scsi: esas2r: Fix typo in comment
scsi: storvsc: Fix typo in comment
scsi: ufs: Split the drivers/scsi/ufs directory
scsi: qla1280: Remove redundant variable
...
Linus Torvalds [Sun, 5 Jun 2022 16:12:28 +0000 (09:12 -0700)]
Merge tag 'hte/for-5.19-rc1' of git://git./linux/kernel/git/tegra/linux
Pull hardware timestamping subsystem from Thierry Reding:
"This contains the new HTE (hardware timestamping engine) subsystem
that has been in the works for a couple of months now.
The infrastructure provided allows for drivers to register as hardware
timestamp providers, while consumers will be able to request events
that they are interested in (such as GPIOs and IRQs) to be timestamped
by the hardware providers.
Note that this currently supports only one provider, but there seems
to be enough interest in this functionality and we expect to see more
drivers added once this is merged"
[ Linus Walleij mentions the Intel PMC in the Elkhart and Tiger Lake
platforms as another future timestamp provider ]
* tag 'hte/for-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: timestamp: Correct id path
dt-bindings: Renamed hte directory to timestamp
hte: Uninitialized variable in hte_ts_get()
hte: Fix off by one in hte_push_ts_ns()
hte: Fix possible use-after-free in tegra_hte_test_remove()
hte: Remove unused including <linux/version.h>
MAINTAINERS: Add HTE Subsystem
hte: Add Tegra HTE test driver
tools: gpio: Add new hardware clock type
gpiolib: cdev: Add hardware timestamp clock type
gpio: tegra186: Add HTE support
gpiolib: Add HTE support
dt-bindings: Add HTE bindings
hte: Add Tegra194 HTE kernel provider
drivers: Add hardware timestamp engine (HTE) subsystem
Documentation: Add HTE subsystem guide
Linus Torvalds [Sun, 5 Jun 2022 16:06:03 +0000 (09:06 -0700)]
Merge tag 'kbuild-v5.19-3' of git://git./linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- Fix build regressions for parisc, csky, nios2, openrisc
- Simplify module builds for CONFIG_LTO_CLANG and CONFIG_X86_KERNEL_IBT
- Remove arch/parisc/nm, which was presumably a workaround for old
tools
- Check the odd combination of EXPORT_SYMBOL and 'static' precisely
- Make external module builds robust against "too long argument error"
- Support j, k keys for moving the cursor in nconfig
* tag 'kbuild-v5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (25 commits)
kbuild: Allow to select bash in a modified environment
scripts: kconfig: nconf: make nconfig accept jk keybindings
modpost: use fnmatch() to simplify match()
modpost: simplify mod->name allocation
kbuild: factor out the common objtool arguments
kbuild: move vmlinux.o link to scripts/Makefile.vmlinux_o
kbuild: clean .tmp_* pattern by make clean
kbuild: remove redundant cleanups in scripts/link-vmlinux.sh
kbuild: rebuild multi-object modules when objtool is updated
kbuild: add cmd_and_savecmd macro
kbuild: make *.mod rule robust against too long argument error
kbuild: make built-in.a rule robust against too long argument error
kbuild: check static EXPORT_SYMBOL* by script instead of modpost
parisc: remove arch/parisc/nm
kbuild: do not create *.prelink.o for Clang LTO or IBT
kbuild: replace $(linked-object) with CONFIG options
kbuild: do not try to parse *.cmd files for objects provided by compiler
kbuild: replace $(if A,A,B) with $(or A,B) in scripts/Makefile.modpost
modpost: squash if...else-if in find_elf_symbol2()
modpost: reuse ARRAY_SIZE() macro for section_mismatch()
...
Linus Torvalds [Sun, 5 Jun 2022 02:07:15 +0000 (19:07 -0700)]
Merge tag 'pull-18-rc1-work.namei' of git://git./linux/kernel/git/viro/vfs
Pull vfs pathname updates from Al Viro:
"Several cleanups in fs/namei.c"
* tag 'pull-18-rc1-work.namei' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
namei: cleanup double word in comment
get rid of dead code in legitimize_root()
fs/namei.c:reserve_stack(): tidy up the call of try_to_unlazy()
Linus Torvalds [Sun, 5 Jun 2022 02:00:05 +0000 (19:00 -0700)]
Merge tag 'pull-18-rc1-work.mount' of git://git./linux/kernel/git/viro/vfs
Pull mount handling updates from Al Viro:
"Cleanups (and one fix) around struct mount handling.
The fix is usermode_driver.c one - once you've done kern_mount(), you
must kern_unmount(); simple mntput() will end up with a leak. Several
failure exits in there messed up that way... In practice you won't hit
those particular failure exits without fault injection, though"
* tag 'pull-18-rc1-work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
move mount-related externs from fs.h to mount.h
blob_to_mnt(): kern_unmount() is needed to undo kern_mount()
m->mnt_root->d_inode->i_sb is a weird way to spell m->mnt_sb...
linux/mount.h: trim includes
uninline may_mount() and don't opencode it in fspick(2)/fsopen(2)
Linus Torvalds [Sun, 5 Jun 2022 01:52:00 +0000 (18:52 -0700)]
Merge tag 'pull-18-rc1-work.fd' of git://git./linux/kernel/git/viro/vfs
Pull file descriptor updates from Al Viro.
- Descriptor handling cleanups
* tag 'pull-18-rc1-work.fd' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Unify the primitives for file descriptor closing
fs: remove fget_many and fput_many interface
io_uring_enter(): don't leave f.flags uninitialized
Linus Torvalds [Sun, 5 Jun 2022 00:42:33 +0000 (17:42 -0700)]
Merge tag '5.19-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs client fixes from Steve French:
"Nine cifs/smb3 client fixes.
Includes DFS fixes, some cleanup of leagcy SMB1 code, duplicated
message cleanup and a double free and deadlock fix"
* tag '5.19-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix uninitialized pointer in error case in dfs_cache_get_tgt_share
cifs: skip trailing separators of prefix paths
cifs: update internal module number
cifs: version operations for smb20 unneeded when legacy support disabled
cifs: do not build smb1ops if legacy support is disabled
cifs: fix potential deadlock in direct reclaim
cifs: when extending a file with falloc we should make files not-sparse
cifs: remove repeated debug message on cifs_put_smb_ses()
cifs: fix potential double free during failed mount
Schspa Shi [Fri, 3 Jun 2022 09:38:52 +0000 (17:38 +0800)]
kbuild: Allow to select bash in a modified environment
This fixes the build error when the system has a default bash version
which is too old to support associative array variables.
The build error log as fellowing:
linux/scripts/check-local-export: line 11: declare: -A: invalid option
declare: usage: declare [-afFirtx] [-p] [name[=value] ...]
Signed-off-by: Schspa Shi <schspa@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Isak Ellmer [Wed, 1 Jun 2022 13:08:19 +0000 (15:08 +0200)]
scripts: kconfig: nconf: make nconfig accept jk keybindings
Make nconfig accept jk keybindings for movement in addition to arrow
keys.
Signed-off-by: Isak Ellmer <isak01@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Masahiro Yamada [Mon, 30 May 2022 09:01:39 +0000 (18:01 +0900)]
modpost: use fnmatch() to simplify match()
Replace the own implementation for wildcard (glob) matching with
a function call to fnmatch().
Also, change the return type to 'bool'.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Masahiro Yamada [Mon, 30 May 2022 09:01:38 +0000 (18:01 +0900)]
modpost: simplify mod->name allocation
mod->name is set to the ELF filename with the suffix ".o" stripped.
The current code calls strdup() and free() to manipulate the string,
but a simpler approach is to pass new_module() with the name length
subtracted by 2.
Also, check if the passed filename ends with ".o" before stripping it.
The current code blindly chops the suffix:
tmp[strlen(tmp) - 2] = '\0'
It will cause buffer under-run if strlen(tmp) < 2;
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Masahiro Yamada [Sat, 28 May 2022 15:47:04 +0000 (00:47 +0900)]
kbuild: factor out the common objtool arguments
scripts/Makefile.build and scripts/link-vmlinux.sh have similar setups
for the objtool arguments.
It was difficult to factor out them because all the vmlinux build rules
were written in a shell script. It is somewhat tedious to touch the two
files every time a new objtool option is supported.
To reduce the code duplication, move the objtool for vmlinux.o into
scripts/Makefile.vmlinux_o. Then, move the common macros to Makefile.lib
so they are shared between Makefile.build and Makefile.vmlinux_o.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com> # LLVM-14 (x86-64)
Masahiro Yamada [Sat, 28 May 2022 15:47:03 +0000 (00:47 +0900)]
kbuild: move vmlinux.o link to scripts/Makefile.vmlinux_o
This is a preparation for moving the objtool rule in the next commit.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com> # LLVM-14 (x86-64)
Masahiro Yamada [Sat, 28 May 2022 15:47:02 +0000 (00:47 +0900)]
kbuild: clean .tmp_* pattern by make clean
Change the "make clean" rule to remove all the .tmp_* files.
.tmp_objdiff is the only exception, which should be removed by
"make mrproper".
Rename the record directory of objdiff, .tmp_objdiff to .objdiff to
avoid the removal by "make clean".
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com> # LLVM-14 (x86-64)
Linus Torvalds [Sat, 4 Jun 2022 21:04:27 +0000 (14:04 -0700)]
Merge tag 'bitmap-for-5.19-rc1' of https://github.com/norov/linux
Pull bitmap updates from Yury Norov:
- bitmap: optimize bitmap_weight() usage, from me
- lib/bitmap.c make bitmap_print_bitmask_to_buf parseable, from Mauro
Carvalho Chehab
- include/linux/find: Fix documentation, from Anna-Maria Behnsen
- bitmap: fix conversion from/to fix-sized arrays, from me
- bitmap: Fix return values to be unsigned, from Kees Cook
It has been in linux-next for at least a week with no problems.
* tag 'bitmap-for-5.19-rc1' of https://github.com/norov/linux: (31 commits)
nodemask: Fix return values to be unsigned
bitmap: Fix return values to be unsigned
KVM: x86: hyper-v: replace bitmap_weight() with hweight64()
KVM: x86: hyper-v: fix type of valid_bank_mask
ia64: cleanup remove_siblinginfo()
drm/amd/pm: use bitmap_{from,to}_arr32 where appropriate
KVM: s390: replace bitmap_copy with bitmap_{from,to}_arr64 where appropriate
lib/bitmap: add test for bitmap_{from,to}_arr64
lib: add bitmap_{from,to}_arr64
lib/bitmap: extend comment for bitmap_(from,to)_arr32()
include/linux/find: Fix documentation
lib/bitmap.c make bitmap_print_bitmask_to_buf parseable
MAINTAINERS: add cpumask and nodemask files to BITMAP_API
arch/x86: replace nodes_weight with nodes_empty where appropriate
mm/vmstat: replace cpumask_weight with cpumask_empty where appropriate
clocksource: replace cpumask_weight with cpumask_empty in clocksource.c
genirq/affinity: replace cpumask_weight with cpumask_empty where appropriate
irq: mips: replace cpumask_weight with cpumask_empty where appropriate
drm/i915/pmu: replace cpumask_weight with cpumask_empty where appropriate
arch/x86: replace cpumask_weight with cpumask_empty where appropriate
...
Linus Torvalds [Sat, 4 Jun 2022 20:50:23 +0000 (13:50 -0700)]
Merge tag 'for-5.19/parisc-2' of git://git./linux/kernel/git/deller/parisc-linux
Pull more parisc architecture updates from Helge Deller:
"A fix to prevent crash at bootup if CONFIG_SCHED_MC is enabled, and
add auto-detection of primary graphics card for framebuffer driver"
* tag 'for-5.19/parisc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc/stifb: Keep track of hardware path of graphics card
parisc/stifb: Implement fb_is_primary_device()
parisc: fix a crash with multicore scheduler
Linus Torvalds [Sat, 4 Jun 2022 20:42:53 +0000 (13:42 -0700)]
Merge tag 'for-linus-5.19-rc1b-tag' of git://git./linux/kernel/git/xen/tip
Pull more xen updates from Juergen Gross:
"Two cleanup patches for Xen related code and (more important) an
update of MAINTAINERS for Xen, as Boris Ostrovsky decided to step
down"
* tag 'for-linus-5.19-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: replace xen_remap() with memremap()
MAINTAINERS: Update Xen maintainership
xen: switch gnttab_end_foreign_access() to take a struct page pointer
Linus Torvalds [Sat, 4 Jun 2022 20:33:12 +0000 (13:33 -0700)]
Merge tag 'perf-tools-for-v5.19-2022-06-04' of git://git./linux/kernel/git/acme/linux
Pull more perf tools updates from Arnaldo Carvalho de Melo:
- Synthesize task events for pre-existing threads when using 'perf lock
--threads', as we need to show task names.
- Fix unwinding with ld.lld (>= version 10.0) linked objects, where
.eh_frame_hdr and .text are in different PT_LOAD program headers,
which makes perf record --call-graph dwarf fail with such obkects.
- Check if 'perf record' hangs in the ARM SPE (Statistical Profiling
Extensions) 'perf test' entry when recording a workload with forks.
- Trace physical address for Arm SPE events, needed for 'perf c2c' to
locate the memory node for samples.
- Fix sorting in percent_rmt_hitm_cmp() in 'perf c2c'.
- Further support for Intel hybrid systems in the evlist and 'perf
record' code.
- Update IBM s/390 vendor event JSON tables.
- Add metrics (JSON) for Intel Sapphirerapids.
- Update metrics for Intel Alderlake.
- Correct typo of sysf 'event_source' directory in the documentation.
* tag 'perf-tools-for-v5.19-2022-06-04' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf vendor events intel: Update metrics for Alderlake
perf vendor events intel: Add metrics for Sapphirerapids
perf c2c: Fix sorting in percent_rmt_hitm_cmp()
perf mem: Trace physical address for Arm SPE events
perf list: Update event description for IBM zEC12/zBC12 to latest level
perf list: Update event description for IBM z196/z114 to latest level
perf list: Update event description for IBM z15 to latest level
perf list: Update event description for IBM z14 to latest level
perf list: Update event description for IBM z13 to latest level
perf list: Update event description for IBM z10 to latest level
perf list: Add IBM z16 event description for s390
perf record: Support sample-read topdown metric group for hybrid platforms
perf lock: Change to synthesize task events
perf unwind: Fix segbase for ld.lld linked objects
perf test arm-spe: Check if perf-record hangs when recording workload with forks
perf docs: Correct typo of event_sources
perf evlist: Extend arch_evsel__must_be_in_group to support hybrid systems
Steve French [Sat, 4 Jun 2022 06:18:37 +0000 (01:18 -0500)]
cifs: fix uninitialized pointer in error case in dfs_cache_get_tgt_share
Set default value of ppath to null.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Helge Deller [Thu, 2 Jun 2022 11:55:26 +0000 (13:55 +0200)]
parisc/stifb: Keep track of hardware path of graphics card
Keep the pa_path (hardware path) of the graphics card in sti_struct and use
this info to give more useful info which card is currently being used.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.10+