Merge remote-tracking branch 'stable/linux-5.10.y' into rpi-5.10.y

drm/vc4: Skip writes to disabled packet RAM

This path actually occurs when audio is started during a hdmi mode set.
As the data will be written by vc4_hdmi_set_infoframes when packet RAM
is enabled again, don't treat as an error

Signed-off-by: Dom Cobley <popcornmix@gmail.com>

drm/vc4: hdmi: Support HDMI YUV output

In addition to the RGB444 output, the BCM2711 HDMI controller supports
the YUV444 and YUV422 output formats.

Let's add support for them in the driver, but still use RGB as the
preferred format.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Always try to have the highest bpc

Currently we take the max_bpc property as the bpc value and do not try
anything else.

However, what the other drivers seem to be doing is that they would try
with the highest bpc allowed by the max_bpc property and the hardware
capabilities, test if it results in an acceptable configuration, and if
not decrease the bpc and try again.

Let's use the same logic.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Take bpp into account for the scrambler

The current code only base its decision for whether the scrambler must be
enabled or not on the pixel clock of the mode, but doesn't take the bits
per color into account.

Let's leverage the new function to compute the clock rate in the
scrambler setup code.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Take the sink maximum TMDS clock into account

In the function that validates that the clock isn't too high, we've only
taken our controller limitations into account so far.

However, the sink can have a limit on the maximum TMDS clock it can deal
with too which is exposed through the EDID and the drm_display_info.

Make sure we check it.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Move clock calculation into its own function

The code to compute our clock rate for a given setup will be called in
multiple places in the next patches, so let's create a separate function
for it.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Move clock validation to its own function

Our code is doing the same clock rate validation in multiple instances.
Let's create a helper to share the rate validation.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Change CSC callback prototype

In order to support the YUV output, we'll need the atomic state to know
what is the state of the associated property in the CSC setup callback.

Let's change the prototype of that callback to allow us to access it.

Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Define colorspace matrices

The current CSC setup code for the BCM2711 uses a sequence of register
writes to configure the CSC depending on whether we output using a full
or limited range.

However, with the upcoming introduction of the YUV output, we're going
to add new matrices to perform the conversions, so we should switch to
something a bit more flexible that takes the matrix as an argument and
programs the CSC accordingly.

Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Replace CSC_CTL hardcoded value by defines

On BCM2711, the HDMI_CSC_CTL register value has been hardcoded to an
opaque value. Let's replace it with properly defined values.

Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Move XBAR setup to csc_setup

On the BCM2711, the HDMI_VEC_INTERFACE_XBAR register configuration
depends on whether we're using an RGB or YUV output. Let's move that
configuration to the CSC setup.

Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Use full range helper in csc functions

The CSC callbacks takes a boolean as an argument to tell whether we're
using the full range or limited range RGB.

However, with the upcoming YUV support, the logic will be a bit more
complex. In order to address this, let's make the callbacks take the
entire mode, and call our new helper to tell whether the full or limited
range RGB should be used.

Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Add full range RGB helper

We're going to need to tell whether we want to run with a full or
limited range RGB output in multiple places in the code, so let's create
a helper that will return whether we need with full range or not.

Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/edid: Rename drm_hdmi_avi_infoframe_colorspace to _colorimetry

The drm_hdmi_avi_infoframe_colorspace() function actually sets the
colorimetry and extended_colorimetry fields in the hdmi_avi_infoframe
structure with DRM_MODE_COLORIMETRY_* values.

To make things worse, the hdmi_avi_infoframe structure also has a
colorspace field used to signal whether an RGB or YUV output is being
used.

Let's remove the inconsistency and allow for the colorspace usage by
renaming the function.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/edid: Don't clear YUV422 if using deep color

The current code, when parsing the EDID Deep Color depths, that the
YUV422 cannot be used, referring to the HDMI 1.3 Specification.

This specification, in its section 6.2.4, indeed states:

  For each supported Deep Color mode, RGB 4:4:4 shall be supported and
  optionally YCBCR 4:4:4 may be supported.

  YCBCR 4:2:2 is not permitted for any Deep Color mode.

This indeed can be interpreted like the code does, but the HDMI 1.4
specification further clarifies that statement in its section 6.2.4:

  For each supported Deep Color mode, RGB 4:4:4 shall be supported and
  optionally YCBCR 4:4:4 may be supported.

  YCBCR 4:2:2 is also 36-bit mode but does not require the further use
  of the Deep Color modes described in section 6.5.2 and 6.5.3.

This means that, even though YUV422 can be used with 12 bit per color,
it shouldn't be treated as a deep color mode.

This deviates from the interpretation of the code and comment, so let's
fix those.

Fixes: d0c94692e0a3 ("drm/edid: Parse and handle HDMI deep color modes.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Linux 5.10.87

Link: https://lore.kernel.org/r/20211215172024.787958154@linuxfoundation.org
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Fox Chen <foxhlchen@gmail.com>
Tested-by: Hulk Robot <hulkrobot@huawei.com>
Tested-by: Salvatore Bonaccorso <carnil@debian.org>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm: ioremap: don't abuse pfn_valid() to check if pfn is in RAM

commit 024591f9a6e0164ec23301784d1e6d8f6cacbe59 upstream.
[ Upstream commit 024591f9a6e0164ec23301784d1e6d8f6cacbe59 ]

The semantics of pfn_valid() is to check presence of the memory map for a
PFN and not whether a PFN is in RAM. The memory map may be present for a
hole in the physical memory and if such hole corresponds to an MMIO range,
__arm_ioremap_pfn_caller() will produce a WARN() and fail:

[    2.863406] WARNING: CPU: 0 PID: 1 at arch/arm/mm/ioremap.c:287 __arm_ioremap_pfn_caller+0xf0/0x1dc
[    2.864812] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.0-09882-ga180bd1d7e16 #1
[    2.865263] Hardware name: Generic DT based system
[    2.865711] Backtrace:
[    2.866063] [<80b07e58>] (dump_backtrace) from [<80b080ac>] (show_stack+0x20/0x24)
[    2.866633]  r7:00000009 r6:0000011f r5:60000153 r4:80ddd1c0
[    2.866922] [<80b0808c>] (show_stack) from [<80b18df0>] (dump_stack_lvl+0x58/0x74)
[    2.867117] [<80b18d98>] (dump_stack_lvl) from [<80b18e20>] (dump_stack+0x14/0x1c)
[    2.867309]  r5:80118cac r4:80dc6774
[    2.867404] [<80b18e0c>] (dump_stack) from [<80122fcc>] (__warn+0xe4/0x150)
[    2.867583] [<80122ee8>] (__warn) from [<80b08850>] (warn_slowpath_fmt+0x88/0xc0)
[    2.867774]  r7:0000011f r6:80dc6774 r5:00000000 r4:814c4000
[    2.867917] [<80b087cc>] (warn_slowpath_fmt) from [<80118cac>] (__arm_ioremap_pfn_caller+0xf0/0x1dc)
[    2.868158]  r9:00000001 r8:9ef00000 r7:80e8b0d4 r6:0009ef00 r5:00000000 r4:00100000
[    2.868346] [<80118bbc>] (__arm_ioremap_pfn_caller) from [<80118df8>] (__arm_ioremap_caller+0x60/0x68)
[    2.868581]  r9:9ef00000 r8:821b6dc0 r7:00100000 r6:00000000 r5:815d1010 r4:80118d98
[    2.868761] [<80118d98>] (__arm_ioremap_caller) from [<80118fcc>] (ioremap+0x28/0x30)
[    2.868958] [<80118fa4>] (ioremap) from [<8062871c>] (__devm_ioremap_resource+0x154/0x1c8)
[    2.869169]  r5:815d1010 r4:814c5d2c
[    2.869263] [<806285c8>] (__devm_ioremap_resource) from [<8062899c>] (devm_ioremap_resource+0x14/0x18)
[    2.869495]  r9:9e9f57a0 r8:814c4000 r7:815d1000 r6:815d1010 r5:8177c078 r4:815cf400
[    2.869676] [<80628988>] (devm_ioremap_resource) from [<8091c6e4>] (fsi_master_acf_probe+0x1a8/0x5d8)
[    2.869909] [<8091c53c>] (fsi_master_acf_probe) from [<80723dbc>] (platform_probe+0x68/0xc8)
[    2.870124]  r9:80e9dadc r8:00000000 r7:815d1010 r6:810c1000 r5:815d1010 r4:00000000
[    2.870306] [<80723d54>] (platform_probe) from [<80721208>] (really_probe+0x1cc/0x470)
[    2.870512]  r7:815d1010 r6:810c1000 r5:00000000 r4:815d1010
[    2.870651] [<8072103c>] (really_probe) from [<807215cc>] (__driver_probe_device+0x120/0x1fc)
[    2.870872]  r7:815d1010 r6:810c1000 r5:810c1000 r4:815d1010
[    2.871013] [<807214ac>] (__driver_probe_device) from [<807216e8>] (driver_probe_device+0x40/0xd8)
[    2.871244]  r9:80e9dadc r8:00000000 r7:815d1010 r6:810c1000 r5:812feaa0 r4:812fe994
[    2.871428] [<807216a8>] (driver_probe_device) from [<80721a58>] (__driver_attach+0xa8/0x1d4)
[    2.871647]  r9:80e9dadc r8:00000000 r7:00000000 r6:810c1000 r5:815d1054 r4:815d1010
[    2.871830] [<807219b0>] (__driver_attach) from [<8071ee8c>] (bus_for_each_dev+0x88/0xc8)
[    2.872040]  r7:00000000 r6:814c4000 r5:807219b0 r4:810c1000
[    2.872194] [<8071ee04>] (bus_for_each_dev) from [<80722208>] (driver_attach+0x28/0x30)
[    2.872418]  r7:810a2aa0 r6:00000000 r5:821b6000 r4:810c1000
[    2.872570] [<807221e0>] (driver_attach) from [<8071f80c>] (bus_add_driver+0x114/0x200)
[    2.872788] [<8071f6f8>] (bus_add_driver) from [<80722ec4>] (driver_register+0x98/0x128)
[    2.873011]  r7:81011d0c r6:814c4000 r5:00000000 r4:810c1000
[    2.873167] [<80722e2c>] (driver_register) from [<80725240>] (__platform_driver_register+0x2c/0x34)
[    2.873408]  r5:814dcb80 r4:80f2a764
[    2.873513] [<80725214>] (__platform_driver_register) from [<80f2a784>] (fsi_master_acf_init+0x20/0x28)
[    2.873766] [<80f2a764>] (fsi_master_acf_init) from [<80f014a8>] (do_one_initcall+0x108/0x290)
[    2.874007] [<80f013a0>] (do_one_initcall) from [<80f01840>] (kernel_init_freeable+0x1ac/0x230)
[    2.874248]  r9:80e9dadc r8:80f3987c r7:80f3985c r6:00000007 r5:814dcb80 r4:80f627a4
[    2.874456] [<80f01694>] (kernel_init_freeable) from [<80b19f44>] (kernel_init+0x20/0x138)
[    2.874691]  r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:80b19f24
[    2.874894]  r4:00000000
[    2.874977] [<80b19f24>] (kernel_init) from [<80100170>] (ret_from_fork+0x14/0x24)
[    2.875231] Exception stack(0x814c5fb0 to 0x814c5ff8)
[    2.875535] 5fa0:                                     00000000 00000000 00000000 00000000
[    2.875849] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    2.876133] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[    2.876363]  r5:80b19f24 r4:00000000
[    2.876683] ---[ end trace b2f74b8536829970 ]---
[    2.876911] fsi-master-acf gpio-fsi: ioremap failed for resource [mem 0x9ef00000-0x9effffff]
[    2.877492] fsi-master-acf gpio-fsi: Error -12 mapping coldfire memory
[    2.877689] fsi-master-acf: probe of gpio-fsi failed with error -12

Use memblock_is_map_memory() instead of pfn_valid() to check if a PFN is in
RAM or not.

Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: a4d5613c4dc6 ("arm: extend pfn_valid to take into account freed memory map alignment")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/lkml/20210630071211.21011-1-rppt@kernel.org/
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm: extend pfn_valid to take into account freed memory map alignment

[ Upstream commit a4d5613c4dc6d413e0733e37db9d116a2a36b9f3 ]

When unused memory map is freed the preserved part of the memory map is
extended to match pageblock boundaries because lots of core mm
functionality relies on homogeneity of the memory map within pageblock
boundaries.

Since pfn_valid() is used to check whether there is a valid memory map
entry for a PFN, make it return true also for PFNs that have memory map
entries even if there is no actual memory populated there.

Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/lkml/20210630071211.21011-1-rppt@kernel.org/
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

memblock: ensure there is no overflow in memblock_overlaps_region()

[ Upstream commit 023accf5cdc1e504a9b04187ec23ff156fe53d90 ]

There maybe an overflow in memblock_overlaps_region() if it is called with
base and size such that

base + size > PHYS_ADDR_MAX

Make sure that memblock_overlaps_region() caps the size to prevent such
overflow and remove now duplicated call to memblock_cap_size() from
memblock_is_region_reserved().

Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/lkml/20210630071211.21011-1-rppt@kernel.org/
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

memblock: align freed memory map on pageblock boundaries with SPARSEMEM

[ Upstream commit f921f53e089a12a192808ac4319f28727b35dc0f ]

When CONFIG_SPARSEMEM=y the ranges of the memory map that are freed are not
aligned to the pageblock boundaries which breaks assumptions about
homogeneity of the memory map throughout core mm code.

Make sure that the freed memory map is always aligned on pageblock
boundaries regardless of the memory model selection.

Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/lkml/20210630071211.21011-1-rppt@kernel.org/
[backport upstream modification in mm/memblock.c to arch/arm/mm/init.c]
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

memblock: free_unused_memmap: use pageblock units instead of MAX_ORDER

[ Upstream commit e2a86800d58639b3acde7eaeb9eb393dca066e08 ]

The code that frees unused memory map uses rounds start and end of the
holes that are freed to MAX_ORDER_NR_PAGES to preserve continuity of the
memory map for MAX_ORDER regions.

Lots of core memory management functionality relies on homogeneity of the
memory map within each pageblock which size may differ from MAX_ORDER in
certain configurations.

Although currently, for the architectures that use free_unused_memmap(),
pageblock_order and MAX_ORDER are equivalent, it is cleaner to have common
notation thought mm code.

Replace MAX_ORDER_NR_PAGES with pageblock_nr_pages and update the comments
to make it more clear why the alignment to pageblock boundaries is
required.

Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/lkml/20210630071211.21011-1-rppt@kernel.org/
[backport upstream modification in mm/memblock.c to arch/arm/mm/init.c]
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf intel-pt: Fix error timestamp setting on the decoder error path

commit 6665b8e4836caa8023cbc7e53733acd234969c8c upstream.

An error timestamp shows the last known timestamp for the queue, but this
is not updated on the error path. Fix by setting it.

Fixes: f4aa081949e7b6 ("perf tools: Add Intel PT decoder")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org # v5.15+
Link: https://lore.kernel.org/r/20211210162303.2288710-8-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
[Adrian: Backport to v5.10]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf intel-pt: Fix missing 'instruction' events with 'q' option

commit a882cc94971093e146ffa1163b140ad956236754 upstream.

FUP packets contain IP information, which makes them also an 'instruction'
event in 'hop' mode i.e. the itrace 'q' option.  That wasn't happening, so
restructure the logic so that FUP events are added along with appropriate
'instruction' and 'branch' events.

Fixes: 7c1b16ba0e26e6 ("perf intel-pt: Add support for decoding FUP/TIP only")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org # v5.15+
Link: https://lore.kernel.org/r/20211210162303.2288710-7-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
[Adrian: Backport to v5.10]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf intel-pt: Fix next 'err' value, walking trace

commit a32e6c5da599dbf49e60622a4dfb5b9b40ece029 upstream.

Code after label 'next:' in intel_pt_walk_trace() assumes 'err' is zero,
but it may not be, if arrived at via a 'goto'. Ensure it is zero.

Fixes: 7c1b16ba0e26e6 ("perf intel-pt: Add support for decoding FUP/TIP only")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org # v5.15+
Link: https://lore.kernel.org/r/20211210162303.2288710-6-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
[Adrian: Backport to v5.10]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf intel-pt: Fix state setting when receiving overflow (OVF) packet

commit c79ee2b2160909889df67c8801352d3e69d43a1a upstream.

An overflow (OVF packet) is treated as an error because it represents a
loss of trace data, but there is no loss of synchronization, so the packet
state should be INTEL_PT_STATE_IN_SYNC not INTEL_PT_STATE_ERR_RESYNC.

To support that, some additional variables must be reset, and the FUP
packet that may follow OVF is treated as an FUP event.

Fixes: f4aa081949e7b6 ("perf tools: Add Intel PT decoder")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org # v5.15+
Link: https://lore.kernel.org/r/20211210162303.2288710-5-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
[Adrian: Backport to v5.10]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf intel-pt: Fix intel_pt_fup_event() assumptions about setting state type

commit 4c761d805bb2d2ead1b9baaba75496152b394c80 upstream.

intel_pt_fup_event() assumes it can overwrite the state type if there has
been an FUP event, but this is an unnecessary and unexpected constraint on
callers.

Fix by touching only the state type flags that are affected by an FUP
event.

Fixes: a472e65fc490a ("perf intel-pt: Add decoder support for ptwrite and power event packets")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org # v5.15+
Link: https://lore.kernel.org/r/20211210162303.2288710-4-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
[Adrian: Backport to v5.10]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf intel-pt: Fix sync state when a PSB (synchronization) packet is found

commit ad106a26aef3a95ac7ca88d033b431661ba346ce upstream.

When syncing, it may be that branch packet generation is not enabled at
that point, in which case there will not immediately be a control-flow
packet, so some packets before a control flow packet turns up, get
ignored.  However, the decoder is in sync as soon as a PSB is found, so
the state should be set accordingly.

Fixes: f4aa081949e7b6 ("perf tools: Add Intel PT decoder")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org # v5.15+
Link: https://lore.kernel.org/r/20211210162303.2288710-3-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
[Adrian: Backport to v5.10]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf intel-pt: Fix some PGE (packet generation enable/control flow packets) usage

commit 057ae59f5a1d924511beb1b09f395bdb316cfd03 upstream.

Packet generation enable (PGE) refers to whether control flow (COFI)
packets are being produced.

PGE may be false even when branch-tracing is enabled, due to being
out-of-context, or outside a filter address range.  Fix some missing PGE
usage.

Fixes: 7c1b16ba0e26e6 ("perf intel-pt: Add support for decoding FUP/TIP only")
Fixes: 839598176b0554 ("perf intel-pt: Allow decoding with branch tracing disabled")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org # v5.15+
Link: https://lore.kernel.org/r/20211210162303.2288710-2-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
[Adrian: Backport to v5.10]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf inject: Fix itrace space allowed for new attributes

commit c29d9792607e67ed8a3f6e9db0d96836d885a8c5 upstream.

The space allowed for new attributes can be too small if existing header
information is large. That can happen, for example, if there are very
many CPUs, due to having an event ID per CPU per event being stored in the
header information.

Fix by adding the existing header.data_offset. Also increase the extra
space allowed to 8KiB and align to a 4KiB boundary for neatness.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lore.kernel.org/lkml/20211125071457.2066863-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
[Adrian: Backport to v5.10]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ethtool: do not perform operations on net devices being unregistered

commit dde91ccfa25fd58f64c397d91b81a4b393100ffa upstream.

There is a short period between a net device starts to be unregistered
and when it is actually gone. In that time frame ethtool operations
could still be performed, which might end up in unwanted or undefined
behaviours[1].

Do not allow ethtool operations after a net device starts its
unregistration. This patch targets the netlink part as the ioctl one
isn't affected: the reference to the net device is taken and the
operation is executed within an rtnl lock section and the net device
won't be found after unregister.

[1] For example adding Tx queues after unregister ends up in NULL
    pointer exceptions and UaFs, such as:

      BUG: KASAN: use-after-free in kobject_get+0x14/0x90
      Read of size 1 at addr ffff88801961248c by task ethtool/755

      CPU: 0 PID: 755 Comm: ethtool Not tainted 5.15.0-rc6+ #778
      Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/014
      Call Trace:
       dump_stack_lvl+0x57/0x72
       print_address_description.constprop.0+0x1f/0x140
       kasan_report.cold+0x7f/0x11b
       kobject_get+0x14/0x90
       kobject_add_internal+0x3d1/0x450
       kobject_init_and_add+0xba/0xf0
       netdev_queue_update_kobjects+0xcf/0x200
       netif_set_real_num_tx_queues+0xb4/0x310
       veth_set_channels+0x1c3/0x550
       ethnl_set_channels+0x524/0x610

Fixes: 041b1c5d4a53 ("ethtool: helper functions for netlink interface")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20211203101318.435618-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hwmon: (dell-smm) Fix warning on /proc/i8k creation error

commit dbd3e6eaf3d813939b28e8a66e29d81cdc836445 upstream.

The removal function is called regardless of whether
/proc/i8k was created successfully or not, the later
causing a WARN() on module removal.
Fix that by only registering the removal function
if /proc/i8k was created successfully.

Tested on a Inspiron 3505.

Fixes: 039ae58503f3 ("hwmon: Allow to compile dell-smm-hwmon driver without /proc/i8k")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20211112171440.59006-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fuse: make sure reclaim doesn't write the inode

commit 5c791fe1e2a4f401f819065ea4fc0450849f1818 upstream.

In writeback cache mode mtime/ctime updates are cached, and flushed to the
server using the ->write_inode() callback.

Closing the file will result in a dirty inode being immediately written,
but in other cases the inode can remain dirty after all references are
dropped.  This result in the inode being written back from reclaim, which
can deadlock on a regular allocation while the request is being served.

The usual mechanisms (GFP_NOFS/PF_MEMALLOC*) don't work for FUSE, because
serving a request involves unrelated userspace process(es).

Instead do the same as for dirty pages: make sure the inode is written
before the last reference is gone.

 - fallocate(2)/copy_file_range(2): these call file_update_time() or
   file_modified(), so flush the inode before returning from the call

 - unlink(2), link(2) and rename(2): these call fuse_update_ctime(), so
   flush the ctime directly from this helper

Reported-by: chenguanyou <chenguanyou@xiaomi.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: Ed Tsai <ed.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bpf: Fix integer overflow in argument calculation for bpf_map_area_alloc

commit 7dd5d437c258bbf4cc15b35229e5208b87b8b4e0 upstream.

In 32-bit architecture, the result of sizeof() is a 32-bit integer so
the expression becomes the multiplication between 2 32-bit integer which
can potentially leads to integer overflow. As a result,
bpf_map_area_alloc() allocates less memory than needed.

Fix this by casting 1 operand to u64.

Fixes: 0d2c4f964050 ("bpf: Eliminate rlimit-based memory accounting for sockmap and sockhash maps")
Fixes: 99c51064fb06 ("devmap: Use bpf_map_area_alloc() for allocating hash buckets")
Fixes: 546ac1ffb70d ("bpf: add devmap, a map for storing net device references")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210613143440.71975-1-minhquangbui99@gmail.com
Signed-off-by: Connor O'Brien <connoro@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: most: dim2: use device release method

commit d445aa402d60014a37a199fae2bba379696b007d upstream.

Commit 723de0f9171e ("staging: most: remove device from interface
structure") moved registration of driver-provided struct device to
the most subsystem. This updated dim2 driver as well.

However, struct device passed to register_device() becomes refcounted,
and must not be explicitly deallocated, but must provide release method
instead. Which is incompatible with managing it via devres.

This patch makes the device structure allocated without devres, adds
device release method, and moves device destruction there.

Fixes: 723de0f9171e ("staging: most: remove device from interface structure")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://lore.kernel.org/r/20211005143448.8660-2-nikita.yoush@cogentembedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: Ignore sparse banks size for an "all CPUs", non-sparse IPI req

commit 3244867af8c065e51969f1bffe732d3ebfd9a7d2 upstream.

Do not bail early if there are no bits set in the sparse banks for a
non-sparse, a.k.a. "all CPUs", IPI request.  Per the Hyper-V spec, it is
legal to have a variable length of '0', e.g. VP_SET's BankContents in
this case, if the request can be serviced without the extra info.

  It is possible that for a given invocation of a hypercall that does
  accept variable sized input headers that all the header input fits
  entirely within the fixed size header. In such cases the variable sized
  input header is zero-sized and the corresponding bits in the hypercall
  input should be set to zero.

Bailing early results in KVM failing to send IPIs to all CPUs as expected
by the guest.

Fixes: 214ff83d4473 ("KVM: x86: hyperv: implement PV IPI send hypercalls")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211207220926.718794-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tracing: Fix a kmemleak false positive in tracing_map

[ Upstream commit f25667e5980a4333729cac3101e5de1bb851f71a ]

Doing the command:
  echo 'hist:key=common_pid.execname,common_timestamp' > /sys/kernel/debug/tracing/events/xxx/trigger

Triggers many kmemleak reports:

unreferenced object 0xffff0000c7ea4980 (size 128):
  comm "bash", pid 338, jiffies 4294912626 (age 9339.324s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<00000000f3469921>] kmem_cache_alloc_trace+0x4c0/0x6f0
    [<0000000054ca40c3>] hist_trigger_elt_data_alloc+0x140/0x178
    [<00000000633bd154>] tracing_map_init+0x1f8/0x268
    [<000000007e814ab9>] event_hist_trigger_func+0xca0/0x1ad0
    [<00000000bf8520ed>] trigger_process_regex+0xd4/0x128
    [<00000000f549355a>] event_trigger_write+0x7c/0x120
    [<00000000b80f898d>] vfs_write+0xc4/0x380
    [<00000000823e1055>] ksys_write+0x74/0xf8
    [<000000008a9374aa>] __arm64_sys_write+0x24/0x30
    [<0000000087124017>] do_el0_svc+0x88/0x1c0
    [<00000000efd0dcd1>] el0_svc+0x1c/0x28
    [<00000000dbfba9b3>] el0_sync_handler+0x88/0xc0
    [<00000000e7399680>] el0_sync+0x148/0x180
unreferenced object 0xffff0000c7ea4980 (size 128):
  comm "bash", pid 338, jiffies 4294912626 (age 9339.324s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<00000000f3469921>] kmem_cache_alloc_trace+0x4c0/0x6f0
    [<0000000054ca40c3>] hist_trigger_elt_data_alloc+0x140/0x178
    [<00000000633bd154>] tracing_map_init+0x1f8/0x268
    [<000000007e814ab9>] event_hist_trigger_func+0xca0/0x1ad0
    [<00000000bf8520ed>] trigger_process_regex+0xd4/0x128
    [<00000000f549355a>] event_trigger_write+0x7c/0x120
    [<00000000b80f898d>] vfs_write+0xc4/0x380
    [<00000000823e1055>] ksys_write+0x74/0xf8
    [<000000008a9374aa>] __arm64_sys_write+0x24/0x30
    [<0000000087124017>] do_el0_svc+0x88/0x1c0
    [<00000000efd0dcd1>] el0_svc+0x1c/0x28
    [<00000000dbfba9b3>] el0_sync_handler+0x88/0xc0
    [<00000000e7399680>] el0_sync+0x148/0x180

The reason is elts->pages[i] is alloced by get_zeroed_page.
and kmemleak will not scan the area alloced by get_zeroed_page.
The address stored in elts->pages will be regarded as leaked.

That is, the elts->pages[i] will have pointers loaded onto it as well, and
without telling kmemleak about it, those pointers will look like memory
without a reference.

To fix this, call kmemleak_alloc to tell kmemleak to scan elts->pages[i]

Link: https://lkml.kernel.org/r/20211124140801.87121-1-chenjun102@huawei.com
Signed-off-by: Chen Jun <chenjun102@huawei.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: add connector type check for CRC source set

[ Upstream commit 2da34b7bb59e1caa9a336e0e20a76b8b6a4abea2 ]

[Why]
IGT bypass test will set crc source as DPRX,and display DM didn`t check
connection type, it run the test on the HDMI connector ,then the kernel
will be crashed because aux->transfer is set null for HDMI connection.
This patch will skip the invalid connection test and fix kernel crash issue.

[How]
Check the connector type while setting the pipe crc source as DPRX or
auto,if the type is not DP or eDP, the crtc crc source will not be set
and report error code to IGT test,IGT will show the this subtest as no
valid crtc/connector combinations found.

116.779714] [IGT] amd_bypass: starting subtest 8bpc-bypass-mode
[ 117.730996] BUG: kernel NULL pointer dereference, address: 0000000000000000
[ 117.731001] #PF: supervisor instruction fetch in kernel mode
[ 117.731003] #PF: error_code(0x0010) - not-present page
[ 117.731004] PGD 0 P4D 0
[ 117.731006] Oops: 0010 [#1] SMP NOPTI
[ 117.731009] CPU: 11 PID: 2428 Comm: amd_bypass Tainted: G OE 5.11.0-34-generic #36~20.04.1-Ubuntu
[ 117.731011] Hardware name: AMD CZN/, BIOS AB.FD 09/07/2021
[ 117.731012] RIP: 0010:0x0
[ 117.731015] Code: Unable to access opcode bytes at RIP 0xffffffffffffffd6.
[ 117.731016] RSP: 0018:ffffa8d64225bab8 EFLAGS: 00010246
[ 117.731017] RAX: 0000000000000000 RBX: 0000000000000020 RCX: ffffa8d64225bb5e
[ 117.731018] RDX: ffff93151d921880 RSI: ffffa8d64225bac8 RDI: ffff931511a1a9d8
[ 117.731022] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 117.731023] CR2: ffffffffffffffd6 CR3: 000000010d5a4000 CR4: 0000000000750ee0
[ 117.731023] PKRU: 55555554
[ 117.731024] Call Trace:
[ 117.731027] drm_dp_dpcd_access+0x72/0x110 [drm_kms_helper]
[ 117.731036] drm_dp_dpcd_read+0xb7/0xf0 [drm_kms_helper]
[ 117.731040] drm_dp_start_crc+0x38/0xb0 [drm_kms_helper]
[ 117.731047] amdgpu_dm_crtc_set_crc_source+0x1ae/0x3e0 [amdgpu]
[ 117.731149] crtc_crc_open+0x174/0x220 [drm]
[ 117.731162] full_proxy_open+0x168/0x1f0
[ 117.731165] ? open_proxy_open+0x100/0x100

BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1546
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Perry Yuan <Perry.Yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: Fix for the no Audio bug with Tiled Displays

[ Upstream commit 5ceaebcda9061c04f439c93961f0819878365c0f ]

[WHY]
It seems like after a series of plug/unplugs we end up in a situation
where tiled display doesnt support Audio.

[HOW]
The issue seems to be related to when we check streams changed after an
HPD, we should be checking the audio_struct as well to see if any of its
values changed.

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Mustapha Ghaddar <mustapha.ghaddar@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: netlink: af_netlink: Prevent empty skb by adding a check on len.

[ Upstream commit f123cffdd8fe8ea6c7fded4b88516a42798797d0 ]

Adding a check on len parameter to avoid empty skb. This prevents a
division error in netem_enqueue function which is caused when skb->len=0
and skb->data_len=0 in the randomized corruption step as shown below.

skb->data[prandom_u32() % skb_headlen(skb)] ^= 1<<(prandom_u32() % 8);

Crash Report:
[  343.170349] netdevsim netdevsim0 netdevsim3: set [1, 0] type 2 family
0 port 6081 - 0
[  343.216110] netem: version 1.3
[  343.235841] divide error: 0000 [#1] PREEMPT SMP KASAN NOPTI
[  343.236680] CPU: 3 PID: 4288 Comm: reproducer Not tainted 5.16.0-rc1+
[  343.237569] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS 1.11.0-2.el7 04/01/2014
[  343.238707] RIP: 0010:netem_enqueue+0x1590/0x33c0 [sch_netem]
[  343.239499] Code: 89 85 58 ff ff ff e8 5f 5d e9 d3 48 8b b5 48 ff ff
ff 8b 8d 50 ff ff ff 8b 85 58 ff ff ff 48 8b bd 70 ff ff ff 31 d2 2b 4f
74 <f7> f1 48 b8 00 00 00 00 00 fc ff df 49 01 d5 4c 89 e9 48 c1 e9 03
[  343.241883] RSP: 0018:ffff88800bcd7368 EFLAGS: 00010246
[  343.242589] RAX: 00000000ba7c0a9c RBX: 0000000000000001 RCX:
0000000000000000
[  343.243542] RDX: 0000000000000000 RSI: ffff88800f8edb10 RDI:
ffff88800f8eda40
[  343.244474] RBP: ffff88800bcd7458 R08: 0000000000000000 R09:
ffffffff94fb8445
[  343.245403] R10: ffffffff94fb8336 R11: ffffffff94fb8445 R12:
0000000000000000
[  343.246355] R13: ffff88800a5a7000 R14: ffff88800a5b5800 R15:
0000000000000020
[  343.247291] FS:  00007fdde2bd7700(0000) GS:ffff888109780000(0000)
knlGS:0000000000000000
[  343.248350] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  343.249120] CR2: 00000000200000c0 CR3: 000000000ef4c000 CR4:
00000000000006e0
[  343.250076] Call Trace:
[  343.250423]  <TASK>
[  343.250713]  ? memcpy+0x4d/0x60
[  343.251162]  ? netem_init+0xa0/0xa0 [sch_netem]
[  343.251795]  ? __sanitizer_cov_trace_pc+0x21/0x60
[  343.252443]  netem_enqueue+0xe28/0x33c0 [sch_netem]
[  343.253102]  ? stack_trace_save+0x87/0xb0
[  343.253655]  ? filter_irq_stacks+0xb0/0xb0
[  343.254220]  ? netem_init+0xa0/0xa0 [sch_netem]
[  343.254837]  ? __kasan_check_write+0x14/0x20
[  343.255418]  ? _raw_spin_lock+0x88/0xd6
[  343.255953]  dev_qdisc_enqueue+0x50/0x180
[  343.256508]  __dev_queue_xmit+0x1a7e/0x3090
[  343.257083]  ? netdev_core_pick_tx+0x300/0x300
[  343.257690]  ? check_kcov_mode+0x10/0x40
[  343.258219]  ? _raw_spin_unlock_irqrestore+0x29/0x40
[  343.258899]  ? __kasan_init_slab_obj+0x24/0x30
[  343.259529]  ? setup_object.isra.71+0x23/0x90
[  343.260121]  ? new_slab+0x26e/0x4b0
[  343.260609]  ? kasan_poison+0x3a/0x50
[  343.261118]  ? kasan_unpoison+0x28/0x50
[  343.261637]  ? __kasan_slab_alloc+0x71/0x90
[  343.262214]  ? memcpy+0x4d/0x60
[  343.262674]  ? write_comp_data+0x2f/0x90
[  343.263209]  ? __kasan_check_write+0x14/0x20
[  343.263802]  ? __skb_clone+0x5d6/0x840
[  343.264329]  ? __sanitizer_cov_trace_pc+0x21/0x60
[  343.264958]  dev_queue_xmit+0x1c/0x20
[  343.265470]  netlink_deliver_tap+0x652/0x9c0
[  343.266067]  netlink_unicast+0x5a0/0x7f0
[  343.266608]  ? netlink_attachskb+0x860/0x860
[  343.267183]  ? __sanitizer_cov_trace_pc+0x21/0x60
[  343.267820]  ? write_comp_data+0x2f/0x90
[  343.268367]  netlink_sendmsg+0x922/0xe80
[  343.268899]  ? netlink_unicast+0x7f0/0x7f0
[  343.269472]  ? __sanitizer_cov_trace_pc+0x21/0x60
[  343.270099]  ? write_comp_data+0x2f/0x90
[  343.270644]  ? netlink_unicast+0x7f0/0x7f0
[  343.271210]  sock_sendmsg+0x155/0x190
[  343.271721]  ____sys_sendmsg+0x75f/0x8f0
[  343.272262]  ? kernel_sendmsg+0x60/0x60
[  343.272788]  ? write_comp_data+0x2f/0x90
[  343.273332]  ? write_comp_data+0x2f/0x90
[  343.273869]  ___sys_sendmsg+0x10f/0x190
[  343.274405]  ? sendmsg_copy_msghdr+0x80/0x80
[  343.274984]  ? slab_post_alloc_hook+0x70/0x230
[  343.275597]  ? futex_wait_setup+0x240/0x240
[  343.276175]  ? security_file_alloc+0x3e/0x170
[  343.276779]  ? write_comp_data+0x2f/0x90
[  343.277313]  ? __sanitizer_cov_trace_pc+0x21/0x60
[  343.277969]  ? write_comp_data+0x2f/0x90
[  343.278515]  ? __fget_files+0x1ad/0x260
[  343.279048]  ? __sanitizer_cov_trace_pc+0x21/0x60
[  343.279685]  ? write_comp_data+0x2f/0x90
[  343.280234]  ? __sanitizer_cov_trace_pc+0x21/0x60
[  343.280874]  ? sockfd_lookup_light+0xd1/0x190
[  343.281481]  __sys_sendmsg+0x118/0x200
[  343.281998]  ? __sys_sendmsg_sock+0x40/0x40
[  343.282578]  ? alloc_fd+0x229/0x5e0
[  343.283070]  ? write_comp_data+0x2f/0x90
[  343.283610]  ? write_comp_data+0x2f/0x90
[  343.284135]  ? __sanitizer_cov_trace_pc+0x21/0x60
[  343.284776]  ? ktime_get_coarse_real_ts64+0xb8/0xf0
[  343.285450]  __x64_sys_sendmsg+0x7d/0xc0
[  343.285981]  ? syscall_enter_from_user_mode+0x4d/0x70
[  343.286664]  do_syscall_64+0x3a/0x80
[  343.287158]  entry_SYSCALL_64_after_hwframe+0x44/0xae
[  343.287850] RIP: 0033:0x7fdde24cf289
[  343.288344] Code: 01 00 48 81 c4 80 00 00 00 e9 f1 fe ff ff 0f 1f 00
48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f
05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d b7 db 2c 00 f7 d8 64 89 01 48
[  343.290729] RSP: 002b:00007fdde2bd6d98 EFLAGS: 00000246 ORIG_RAX:
000000000000002e
[  343.291730] RAX: ffffffffffffffda RBX: 0000000000000000 RCX:
00007fdde24cf289
[  343.292673] RDX: 0000000000000000 RSI: 00000000200000c0 RDI:
0000000000000004
[  343.293618] RBP: 00007fdde2bd6e20 R08: 0000000100000001 R09:
0000000000000000
[  343.294557] R10: 0000000100000001 R11: 0000000000000246 R12:
0000000000000000
[  343.295493] R13: 0000000000021000 R14: 0000000000000000 R15:
00007fdde2bd7700
[  343.296432]  </TASK>
[  343.296735] Modules linked in: sch_netem ip6_vti ip_vti ip_gre ipip
sit ip_tunnel geneve macsec macvtap tap ipvlan macvlan 8021q garp mrp
hsr wireguard libchacha20poly1305 chacha_x86_64 poly1305_x86_64
ip6_udp_tunnel udp_tunnel libblake2s blake2s_x86_64 libblake2s_generic
curve25519_x86_64 libcurve25519_generic libchacha xfrm_interface
xfrm6_tunnel tunnel4 veth netdevsim psample batman_adv nlmon dummy team
bonding tls vcan ip6_gre ip6_tunnel tunnel6 gre tun ip6t_rpfilter
ipt_REJECT nf_reject_ipv4 ip6t_REJECT nf_reject_ipv6 xt_conntrack ip_set
ebtable_nat ebtable_broute ip6table_nat ip6table_mangle
ip6table_security ip6table_raw iptable_nat nf_nat nf_conntrack
nf_defrag_ipv6 nf_defrag_ipv4 iptable_mangle iptable_security
iptable_raw ebtable_filter ebtables rfkill ip6table_filter ip6_tables
iptable_filter ppdev bochs drm_vram_helper drm_ttm_helper ttm
drm_kms_helper cec parport_pc drm joydev floppy parport sg syscopyarea
sysfillrect sysimgblt i2c_piix4 qemu_fw_cfg fb_sys_fops pcspkr
[  343.297459]  ip_tables xfs virtio_net net_failover failover sd_mod
sr_mod cdrom t10_pi ata_generic pata_acpi ata_piix libata virtio_pci
virtio_pci_legacy_dev serio_raw virtio_pci_modern_dev dm_mirror
dm_region_hash dm_log dm_mod
[  343.311074] Dumping ftrace buffer:
[  343.311532]    (ftrace buffer empty)
[  343.312040] ---[ end trace a2e3db5a6ae05099 ]---
[  343.312691] RIP: 0010:netem_enqueue+0x1590/0x33c0 [sch_netem]
[  343.313481] Code: 89 85 58 ff ff ff e8 5f 5d e9 d3 48 8b b5 48 ff ff
ff 8b 8d 50 ff ff ff 8b 85 58 ff ff ff 48 8b bd 70 ff ff ff 31 d2 2b 4f
74 <f7> f1 48 b8 00 00 00 00 00 fc ff df 49 01 d5 4c 89 e9 48 c1 e9 03
[  343.315893] RSP: 0018:ffff88800bcd7368 EFLAGS: 00010246
[  343.316622] RAX: 00000000ba7c0a9c RBX: 0000000000000001 RCX:
0000000000000000
[  343.317585] RDX: 0000000000000000 RSI: ffff88800f8edb10 RDI:
ffff88800f8eda40
[  343.318549] RBP: ffff88800bcd7458 R08: 0000000000000000 R09:
ffffffff94fb8445
[  343.319503] R10: ffffffff94fb8336 R11: ffffffff94fb8445 R12:
0000000000000000
[  343.320455] R13: ffff88800a5a7000 R14: ffff88800a5b5800 R15:
0000000000000020
[  343.321414] FS:  00007fdde2bd7700(0000) GS:ffff888109780000(0000)
knlGS:0000000000000000
[  343.322489] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  343.323283] CR2: 00000000200000c0 CR3: 000000000ef4c000 CR4:
00000000000006e0
[  343.324264] Kernel panic - not syncing: Fatal exception in interrupt
[  343.333717] Dumping ftrace buffer:
[  343.334175]    (ftrace buffer empty)
[  343.334653] Kernel Offset: 0x13600000 from 0xffffffff81000000
(relocation range: 0xffffffff80000000-0xffffffffbfffffff)
[  343.336027] Rebooting in 86400 seconds..

Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20211129175328.55339-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i2c: rk3x: Handle a spurious start completion interrupt flag

[ Upstream commit 02fe0fbd8a21e183687925c3a266ae27dda9840f ]

In a typical read transfer, start completion flag is being set after
read finishes (notice ipd bit 4 being set):

trasnfer poll=0
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 33

This causes I2C transfer being aborted in polled mode from a stop completion
handler:

trasnfer poll=1
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 0
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 13
i2c stop
rk3x-i2c fdd40000.i2c: unexpected irq in STOP: 0x10

Clearing the START flag after read fixes the issue without any obvious
side effects.

This issue was dicovered on RK3566 when adding support for powering
off the RK817 PMIC.

Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

parisc/agp: Annotate parisc agp init functions with __init

[ Upstream commit 8d88382b7436551a9ebb78475c546b670790cbf6 ]

Signed-off-by: Helge Deller <deller@gmx.de>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: hda/hdmi: fix HDA codec entry table order for ADL-P

[ Upstream commit 289047db1143c42c81820352f195a393ff639a52 ]

Keep the HDA_CODEC_ENTRY entries sorted by the codec VID. ADL-P
is the only misplaced Intel HDMI codec.

Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211130124732.696896-2-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: hda: Add Intel DG2 PCI ID and HDMI codec vid

[ Upstream commit d85ffff5302b1509efc482e8877c253b0a668b33 ]

Add HD Audio PCI ID and HDMI codec vendor ID for Intel DG2.

Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211130124732.696896-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx4_en: Update reported link modes for 1/10G

[ Upstream commit 2191b1dfef7d45f44b5008d2148676d9f2c82874 ]

When link modes were initially added in commit 2c762679435dc
("net/mlx4_en: Use PTYS register to query ethtool settings") and
later updated for the new ethtool API in commit 3d8f7cc78d0eb
("net: mlx4: use new ETHTOOL_G/SSETTINGS API") the only 1/10G non-baseT
link modes configured were 1000baseKX, 10000baseKX4 and 10000baseKR.
It looks like these got picked to represent other modes since nothing
better was available.

Switch to using more specific link modes added in commit 5711a98221443
("net: ethtool: add support for 1000BaseX and missing 10G link modes").

Tested with MCX311A-XCAT connected via DAC.
Before:

% sudo ethtool enp3s0
Settings for enp3s0:
Supported ports: [ FIBRE ]
Supported link modes:   1000baseKX/Full
                        10000baseKR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes:  1000baseKX/Full
                        10000baseKR/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Supports Wake-on: d
Wake-on: d
        Current message level: 0x00000014 (20)
                               link ifdown
Link detected: yes

With this change:

% sudo ethtool enp3s0
Settings for enp3s0:
Supported ports: [ FIBRE ]
Supported link modes:   1000baseX/Full
                        10000baseCR/Full
                          10000baseSR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes:  1000baseX/Full
                          10000baseCR/Full
                          10000baseSR/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Supports Wake-on: d
Wake-on: d
        Current message level: 0x00000014 (20)
                               link ifdown
Link detected: yes

Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Signed-off-by: Erik Ekman <erik@kryo.se>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Revert "tty: serial: fsl_lpuart: drop earlycon entry for i.MX8QXP"

[ Upstream commit 4e9679738a918d8a482ac6a2cb2bb871f094bb84 ]

Revert commit b4b844930f27 ("tty: serial: fsl_lpuart: drop earlycon entry
for i.MX8QXP"), because this breaks earlycon support on imx8qm/imx8qxp.
While it is true that for earlycon there is no difference between
i.MX8QXP and i.MX7ULP (for now at least), there are differences
regarding clocks and fixups for wakeup support. For that reason it was
deemed unacceptable to add the imx7ulp compatible to device tree in
order to get earlycon working again.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211124073109.805088-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/test_unwind: use raw opcode instead of invalid instruction

[ Upstream commit 53ae7230918154d1f4281d7aa3aae9650436eadf ]

Building with clang & LLVM_IAS=1 leads to an error:
    arch/s390/lib/test_unwind.c:179:4: error: invalid register pair
                        "       mvcl    %%r1,%%r1\n"
                        ^

The test creates an invalid instruction that would trap at runtime, but the
LLVM inline assembler tries to validate it at compile time too.

Use the raw instruction opcode instead.

Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Ilie Halip <ilie.halip@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Suggested-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1421
Link: https://lore.kernel.org/r/20211117174822.3632412-1-ilie.halip@gmail.com
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
[hca@linux.ibm.com: use illegal opcode, and update comment]
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: arm64: Save PSTATE early on exit

[ Upstream commit 83bb2c1a01d7127d5adc7d69d7aaa3f7072de2b4 ]

In order to be able to use primitives such as vcpu_mode_is_32bit(),
we need to synchronize the guest PSTATE. However, this is currently
done deep into the bowels of the world-switch code, and we do have
helpers evaluating this much earlier (__vgic_v3_perform_cpuif_access
and handle_aarch32_guest, for example).

Move the saving of the guest pstate into the early fixups, which
cures the first issue. The second one will be addressed separately.

Tested-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Fuad Tabba <tabba@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm/dsi: set default num_data_lanes

[ Upstream commit cd92cc187c053ab010a1570e2d61d68394a5c725 ]

If "data_lanes" property of the dsi output endpoint is missing in
the DT, num_data_lanes would be 0 by default, which could cause
dsi_host_attach() to fail if dsi->lanes is set to a non-zero value
by the bridge driver.

According to the binding document of msm dsi controller, the
input/output endpoint of the controller is expected to have 4 lanes.
So let's set num_data_lanes to 4 by default.

Signed-off-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211030100812.1.I6cd9af36b723fed277d34539d3b2ba4ca233ad2d@changeid
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nfc: fix segfault in nfc_genl_dump_devices_done

commit fd79a0cbf0b2e34bcc45b13acf962e2032a82203 upstream.

When kmalloc in nfc_genl_dump_devices() fails then
nfc_genl_dump_devices_done() segfaults as below

KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
CPU: 0 PID: 25 Comm: kworker/0:1 Not tainted 5.16.0-rc4-01180-g2a987e65025e-dirty #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-6.fc35 04/01/2014
Workqueue: events netlink_sock_destruct_work
RIP: 0010:klist_iter_exit+0x26/0x80
Call Trace:
<TASK>
class_dev_iter_exit+0x15/0x20
nfc_genl_dump_devices_done+0x3b/0x50
genl_lock_done+0x84/0xd0
netlink_sock_destruct+0x8f/0x270
__sk_destruct+0x64/0x3b0
sk_destruct+0xa8/0xd0
__sk_free+0x2e8/0x3d0
sk_free+0x51/0x90
netlink_sock_destruct_work+0x1c/0x20
process_one_work+0x411/0x710
worker_thread+0x6fd/0xa80

Link: https://syzkaller.appspot.com/bug?id=fc0fa5a53db9edd261d56e74325419faf18bd0df
Reported-by: syzbot+f9f76f4a0766420b4a02@syzkaller.appspotmail.com
Signed-off-by: Tadeusz Struk <tadeusz.struk@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211208182742.340542-1-tadeusz.struk@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/bcm2835-isp: Fix cleanup after init fail

bcm2835_isp_remove is called on an initialisation failure, but at that
point the drvdata hasn't been set. This causes a crash when e.g. using
the cutdown firmware (gpu_mem=16).

Move platform_set_drvdata before the instance probing loop to avoid the
problem.

See: https://github.com/raspberrypi/linux/issues/4774

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

Linux 5.10.86

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: selftest: conntrack_vrf.sh: fix file permission

When backporting 33b8aad21ac1 ("selftests: netfilter: add a
vrf+conntrack testcase") to this stable branch, the executable bits were
not properly set on the
tools/testing/selftests/netfilter/conntrack_vrf.sh file due to quilt not
honoring them.

Fix this up manually by setting the correct mode.

Reported-by: "Rantala, Tommi T. (Nokia - FI/Espoo)" <tommi.t.rantala@nokia.com>
Link: https://lore.kernel.org/r/234d7a6a81664610fdf21ac72730f8bd10d3f46f.camel@nokia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "media: bcm2835-codec: Limit video callbacks"

This reverts commit f814bfc5f4d3005eb266a1556be8b7b8770629bd.

The commit caused media stalls with kodi and stateful
v4l2 video decode.

John is now using a different way of limiting latency
through stateful v4l2 so this is not required.

Merge remote-tracking branch 'stable/linux-5.10.y' into rpi-5.10.y

Revert "kbuild: Disable gcc plugins"

This reverts commit d62b4f2f5742bf39892acf8c6804fffee174d371.

ASoC:ma120x0p: Increase maximum sample rate to 192KHz

Change the maximum sample rate for the amplifier to
192KHz as given in the Infineon specification.

Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>

dtoverlays: Add option to select camera as on CAM0 of CM

Parameterise the overlays so that they can have an optional
cam0 parameter to switch to i2c_vc and csi0.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

ARM: dts: bcm2711-cm4s Correct i2c0mux to use 0/1 and 28/29 & 2 regulators

CM4S follows CM1/3, so based on the documentation cameras/displays
connect to 0/1 and 28/29, not 0/1 and 44/45.

Likewise the camera regulator controls are independent as on CM1/3.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

media: i2c: ov7251: Make the enable GPIO optional.

Not all implementations wire up the enable GPIO and may just tie
it to a supply rail.
Make it optional.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

dtoverlays: Convert ov5647 to use the regulator framework

Fixing up shutdown GPIOs via overrides is ugly, and doesn't work
on eg CM4 where both cameras share the same shutdown GPIO.

The driver is now updated to use the regulator framework, so switch
to using that instead.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

media: i2c: ov5647: Add support for regulator control.

The driver supported using GPIOs to control the shutdown line,
but no regulator control.

Add regulator hooks.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

dtoverlays: Convert the camera sensor overlays to use the new regs and clks.

Now that we have regulators and clocks defined in the base DT for
image sensors, switch the overlays to use them.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

dt: Create static regulators and clocks for camera nodes

Unloading regulators through dynamic device tree doesn't work
as the regulators will unregister whilst clients are still
registered. Whilst the regulator framework does WARN when that
happens, the client putting the regulator then typically results
in a NULL dereference and badness.

Instead of creating regulators and clocks from the overlays,
create regulators and clocks for the sensors in the base DT.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

drm/vc4: Fix build without DRM_VC4_HDMI_CEC

As reported by @asavah.

Fixes: https://github.com/raspberrypi/linux/issues/4771

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

usb: xhci: add VLI_TRB_CACHE_BUG quirk

The VL805 fetches up to 4 transfer TRBs at a time. TRB reads don't cross
a 64B boundary, and if a TRB is fetched and is not on a 64B boundary,
the read is sized up to the next 64B boundary.

However the VL805 implements a readahead prefetch for TRBs on a transfer
ring. This fetches the next 64B after any TRB read has happened. Near
the end of a ring segment, the prefetcher can read the first 64B of the
next page in physical memory and this is where the behaviour causes a
bug.

The controller does not tag reads with which endpoint they are for, so
if the start of the next page is a ring segment used by a victim
endpoint, and the victim endpoint is about to fetch TRBs from the start
of the segment, the victim endpoint will read from the prefetched data
and not perform a read to main memory. If the data is stale, the ring
cycle state bit may not be correct and the endpoint will silently halt.

Adjust trbs_per_seg for transfer rings allocated for this controller.

See https://github.com/raspberrypi/linux/issues/4685

Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>

xhci: refactor out TRBS_PER_SEGMENT define in runtime code

In anticipation of adjusting the number of utilised TRBs in a ring
segment, add trbs_per_seg to struct xhci_ring and use this instead
of a compile-time define.

Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>

Revert "xhci: add a quirk to work around a suspected cache bug on VLI controllers"

This reverts commit a1d0f808d4a0b7f7053095cd4ab97a4276bed9ff.

Linux 5.10.85

Link: https://lore.kernel.org/r/20211213092939.074326017@linuxfoundation.org
Tested-by: Fox Chen <foxhlchen@gmail.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Documentation/Kbuild: Remove references to gcc-plugin.sh

commit 1cabe74f148f7b99d9f08274a62467f96c870f07 upstream.

gcc-plugin.sh has been removed in commit
1e860048c53e ("gcc-plugins: simplify GCC plugin-dev capability test").

Signed-off-by: Robert Karszniewicz <r.karszniewicz@phytec.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MAINTAINERS: adjust GCC PLUGINS after gcc-plugin.sh removal

commit 5136bb8c8b5872676f397b27f93a30568baf3a25 upstream.

Commit 1e860048c53e ("gcc-plugins: simplify GCC plugin-dev capability test")
removed ./scripts/gcc-plugin.sh, but missed to adjust MAINTAINERS.

Hence, ./scripts/get_maintainers.pl --self-test=patterns warns:

  warning: no file matches    F:    scripts/gcc-plugin.sh

Adjust entries in GGC PLUGINS section after this file removal.

Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

doc: gcc-plugins: update gcc-plugins.rst

commit 9b6164342e981d751e69f5a165dd596ffcdfd6fe upstream.

This document was written a long time ago. Update it.

[1] Drop the version information

The range of the supported GCC versions are always changing. The
current minimal GCC version is 4.9, and commit 1e860048c53e
("gcc-plugins: simplify GCC plugin-dev capability test") removed the
old code accordingly.

We do not need to mention specific version ranges like "all gcc versions
from 4.5 to 6.0" since we forget to update the documentation when we
raise the minimal compiler version.

[2] Drop the C compiler statements

Since commit 77342a02ff6e ("gcc-plugins: drop support for GCC <= 4.7")
the GCC plugin infrastructure only supports g++.

[3] Drop supported architectures

As of v5.11-rc4, the infrastructure supports more architectures;
arm, arm64, mips, powerpc, riscv, s390, um, and x86. (just grep
"select HAVE_GCC_PLUGINS") Again, we miss to update this document when a
new architecture is supported. Let's just say "only some architectures".

[4] Update the apt-get example

We are now discussing to bump the minimal version to GCC 5. The GCC 4.9
support will be removed sooner or later. Change the package example to
gcc-10-plugin-dev while we are here.

[5] Update the build target

Since commit ce2fd53a10c7 ("kbuild: descend into scripts/gcc-plugins/
via scripts/Makefile"), "make gcc-plugins" is not supported.
"make scripts" builds all the enabled plugins, including some other
tools.

[6] Update the steps for adding a new plugin

At first, all CONFIG options for GCC plugins were located in arch/Kconfig.
After commit 45332b1bdfdc ("gcc-plugins: split out Kconfig entries to
scripts/gcc-plugins/Kconfig"), scripts/gcc-plugins/Kconfig became the
central place to collect plugin CONFIG options. In my understanding,
this requirement no longer exists because commit 9f671e58159a ("security:
Create "kernel hardening" config area") moved some of plugin CONFIG
options to another file. Find an appropriate place to add the new CONFIG.

The sub-directory support was never used by anyone, and removed by
commit c17d6179ad5a ("gcc-plugins: remove unused GCC_PLUGIN_SUBDIR").

Remove the useless $(src)/ prefix.

Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kbuild: simplify GCC_PLUGINS enablement in dummy-tools/gcc

commit f4c3b83b75b91c5059726cb91e3165cc01764ce7 upstream.

With commit 1e860048c53e ("gcc-plugins: simplify GCC plugin-dev
capability test") applied, this hunk can be way simplified because
now scripts/gcc-plugins/Kconfig only checks plugin-version.h

Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bpf: Add selftests to cover packet access corner cases

commit b560b21f71eb4ef9dfc7c8ec1d0e4d7f9aa54b51 upstream.

This commit adds BPF verifier selftests that cover all corner cases by
packet boundary checks. Specifically, 8-byte packet reads are tested at
the beginning of data and at the beginning of data_meta, using all kinds
of boundary checks (all comparison operators: <, >, <=, >=; both
permutations of operands: data + length compared to end, end compared to
data + length). For each case there are three tests:

1. Length is just enough for an 8-byte read. Length is either 7 or 8,
   depending on the comparison.

2. Length is increased by 1 - should still pass the verifier. These
   cases are useful, because they failed before commit 2fa7d94afc1a
   ("bpf: Fix the off-by-two error in range markings").

3. Length is decreased by 1 - should be rejected by the verifier.

Some existing tests are just renamed to avoid duplication.

Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211207081521.41923-1-maximmi@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

misc: fastrpc: fix improper packet size calculation

commit 3a1bf591e9a410f220b7405a142a47407394a1d5 upstream.

The buffer list is sorted and this is not being considered while
calculating packet size. This would lead to improper copy length
calculation for non-dmaheap buffers which would eventually cause
sending improper buffers to DSP.

Fixes: c68cfb718c8f ("misc: fastrpc: Add support for context Invoke method")
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Jeya R <jeyr@codeaurora.org>
Link: https://lore.kernel.org/r/1637771481-4299-1-git-send-email-jeyr@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

irqchip: nvic: Fix offset for Interrupt Priority Offsets

commit c5e0cbe2858d278a27d5b3fe31890aea5be064c4 upstream.

According to ARM(v7M) ARM Interrupt Priority Offsets located at
0xE000E400-0xE000E5EC, while 0xE000E300-0xE000E33C covers read-only
Interrupt Active Bit Registers

Fixes: 292ec080491d ("irqchip: Add support for ARMv7-M NVIC")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211201110259.84857-1-vladimir.murzin@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

irqchip/irq-gic-v3-its.c: Force synchronisation when issuing INVALL

commit b383a42ca523ce54bcbd63f7c8f3cf974abc9b9a upstream.

INVALL CMD specifies that the ITS must ensure any caching associated with
the interrupt collection defined by ICID is consistent with the LPI
configuration tables held in memory for all Redistributors. SYNC is
required to ensure that INVALL is executed.

Currently, LPI configuration data may be inconsistent with that in the
memory within a short period of time after the INVALL command is executed.

Signed-off-by: Wudi Wang <wangwudi@hisilicon.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Fixes: cc2d3216f53c ("irqchip: GICv3: ITS command queue")
Link: https://lore.kernel.org/r/20211208015429.5007-1-zhangshaokun@hisilicon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

irqchip/armada-370-xp: Fix support for Multi-MSI interrupts

commit d0a553502efd545c1ce3fd08fc4d423f8e4ac3d6 upstream.

irq-armada-370-xp driver already sets MSI_FLAG_MULTI_PCI_MSI flag into
msi_domain_info structure. But allocated interrupt numbers for Multi-MSI
needs to be properly aligned otherwise devices send MSI interrupt with
wrong number.

Fix this issue by using function bitmap_find_free_region() instead of
bitmap_find_next_zero_area() to allocate aligned interrupt numbers.

Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: a71b9412c90c ("irqchip/armada-370-xp: Allow allocation of multiple MSIs")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211125130057.26705-2-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

irqchip/armada-370-xp: Fix return value of armada_370_xp_msi_alloc()

commit ce20eff57361e72878a772ef08b5239d3ae102b6 upstream.

IRQ domain alloc function should return zero on success. Non-zero value
indicates failure.

Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: fcc392d501bd ("irqchip/armada-370-xp: Use the generic MSI infrastructure")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211125130057.26705-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

irqchip/aspeed-scu: Replace update_bits with write_bits.

commit 8958389681b929fcc7301e7dc5f0da12e4a256a0 upstream.

The interrupt status bits are cleared by writing 1, we should force a
write to clear the interrupt without checking if the value has changed.

Fixes: 04f605906ff0 ("irqchip: Add Aspeed SCU interrupt controller")
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211124094348.11621-1-billy_tsai@aspeedtech.com
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

csky: fix typo of fpu config macro

commit a0793fdad9a11a32bc6d21317c93c83f4aa82ebc upstream.

Fix typo which will cause fpe and privilege exception error.

Signed-off-by: Kelly Devilliv <kelly.devilliv@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: accel: kxcjk-1013: Fix possible memory leak in probe and remove

commit 70c9774e180d151abaab358108e3510a8e615215 upstream.

When ACPI type is ACPI_SMO8500, the data->dready_trig will not be set, the
memory allocated by iio_triggered_buffer_setup() will not be freed, and cause
memory leak as follows:

unreferenced object 0xffff888009551400 (size 512):
  comm "i2c-SMO8500-125", pid 911, jiffies 4294911787 (age 83.852s)
  hex dump (first 32 bytes):
    02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 20 e2 e5 c0 ff ff ff ff  ........ .......
  backtrace:
    [<0000000041ce75ee>] kmem_cache_alloc_trace+0x16d/0x360
    [<000000000aeb17b0>] iio_kfifo_allocate+0x41/0x130 [kfifo_buf]
    [<000000004b40c1f5>] iio_triggered_buffer_setup_ext+0x2c/0x210 [industrialio_triggered_buffer]
    [<000000004375b15f>] kxcjk1013_probe+0x10c3/0x1d81 [kxcjk_1013]

Fix it by remove data->dready_trig condition in probe and remove.

Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: a25691c1f967 ("iio: accel: kxcjk1013: allow using an external trigger")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Cc: <Stable@vger.kernel.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211025124159.2700301-1-yangyingliang@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: ad7768-1: Call iio_trigger_notify_done() on error

commit 6661146427cbbce6d1fe3dbb11ff1c487f55799a upstream.

IIO trigger handlers must call iio_trigger_notify_done() when done. This
must be done even when an error occurred. Otherwise the trigger will be
seen as busy indefinitely and the trigger handler will never be called
again.

The ad7768-1 driver neglects to call iio_trigger_notify_done() when there
is an error reading the converter data. Fix this by making sure that
iio_trigger_notify_done() is included in the error exit path.

Fixes: a5f8c7da3dbe ("iio: adc: Add AD7768-1 ADC basic support")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211101144055.13858-2-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: axp20x_adc: fix charging current reporting on AXP22x

commit 92beafb76a31bdc02649eb44e93a8e4f4cfcdbe8 upstream.

Both the charging and discharging currents on AXP22x are stored as
12-bit integers, in accordance with the datasheet.
It's also confirmed by vendor BSP (axp20x_adc.c:axp22_icharge_to_mA).

The scale factor of 0.5 is never mentioned in datasheet, nor in the
vendor source code. I think it was here to compensate for
erroneous addition bit in register width.

Tested on custom A40i+AXP221s board with external ammeter as
a reference.

Fixes: 0e34d5de961d ("iio: adc: add support for X-Powers AXP20X and AXP22X PMICs ADCs")
Signed-off-by: Evgeny Boger <boger@wirenboard.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20211116213746.264378-1-boger@wirenboard.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: stm32: fix a current leak by resetting pcsel before disabling vdda

commit f711f28e71e965c0d1141c830fa7131b41abbe75 upstream.

Some I/Os are connected to ADC input channels, when the corresponding bit
in PCSEL register are set on STM32H7 and STM32MP15. This is done in the
prepare routine of stm32-adc driver.
There are constraints here, as PCSEL shouldn't be set when VDDA supply
is disabled. Enabling/disabling of VDDA supply in done via stm32-adc-core
runtime PM routines (before/after ADC is enabled/disabled).

Currently, PCSEL remains set when disabling ADC. Later on, PM runtime
can disable the VDDA supply. This creates some conditions on I/Os that
can start to leak current.
So PCSEL needs to be cleared when disabling the ADC.

Fixes: 95e339b6e85d ("iio: adc: stm32: add support for STM32H7")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/1634905169-23762-1-git-send-email-fabrice.gasnier@foss.st.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: at91-sama5d2: Fix incorrect sign extension

commit 652e7df485c6884d552085ae2c73efa6cfea3547 upstream.

Use scan_type when processing raw data which also fixes that the sign
extension was from the wrong bit.

Use channel definition as root of trust and replace constant
when reading elements directly using the raw sysfs attributes.

Fixes: 6794e23fa3fe ("iio: adc: at91-sama5d2_adc: add support for oversampling resolution")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211104082413.3681212-9-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: dln2: Check return value of devm_iio_trigger_register()

commit 90751fb9f224e0e1555b49a8aa9e68f6537e4cec upstream.

Registering a trigger can fail and the return value of
devm_iio_trigger_register() must be checked. Otherwise undefined behavior
can occur when the trigger is used.

Fixes: 7c0299e879dd ("iio: adc: Add support for DLN2 ADC")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211101133043.6974-1-lars@metafoo.de
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: dln2-adc: Fix lockdep complaint

commit 59f92868176f191eefde70d284bdfc1ed76a84bc upstream.

When reading the voltage:

$ cat /sys/bus/iio/devices/iio\:device0/in_voltage0_raw

Lockdep complains:

[  153.910616] ======================================================
[  153.916918] WARNING: possible circular locking dependency detected
[  153.923221] 5.14.0+ #5 Not tainted
[  153.926692] ------------------------------------------------------
[  153.932992] cat/717 is trying to acquire lock:
[  153.937525] c2585358 (&indio_dev->mlock){+.+.}-{3:3}, at: iio_device_claim_direct_mode+0x28/0x44
[  153.946541]
               but task is already holding lock:
[  153.952487] c2585860 (&dln2->mutex){+.+.}-{3:3}, at: dln2_adc_read_raw+0x94/0x2bc [dln2_adc]
[  153.961152]
               which lock already depends on the new lock.

Fix this by not calling into the iio core underneath the dln2->mutex lock.

Fixes: 7c0299e879dd ("iio: adc: Add support for DLN2 ADC")
Cc: Jack Andersen <jackoalan@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://lore.kernel.org/r/20211018113731.25723-1-noralf@tronnes.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: itg3200: Call iio_trigger_notify_done() on error

commit 67fe29583e72b2103abb661bb58036e3c1f00277 upstream.

IIO trigger handlers must call iio_trigger_notify_done() when done. This
must be done even when an error occurred. Otherwise the trigger will be
seen as busy indefinitely and the trigger handler will never be called
again.

The itg3200 driver neglects to call iio_trigger_notify_done() when there is
an error reading the gyro data. Fix this by making sure that
iio_trigger_notify_done() is included in the error exit path.

Fixes: 9dbf091da080 ("iio: gyro: Add itg3200")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211101144055.13858-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: kxsd9: Don't return error code in trigger handler

commit 45febe0d63917ee908198c5be08511c64ee1790a upstream.

IIO trigger handlers need to return one of the irqreturn_t values.
Returning an error code is not supported.

The kxsd9 interrupt handler returns an error code if reading the data
registers fails. In addition when exiting due to an error the trigger
handler does not call `iio_trigger_notify_done()`. Which when not done
keeps the triggered disabled forever.

Modify the code so that the function returns a valid irqreturn_t value as
well as calling `iio_trigger_notify_done()` on all exit paths.

Since we can't return the error code make sure to at least log it as part
of the error message.

Fixes: 0427a106a98a ("iio: accel: kxsd9: Add triggered buffer handling")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211024171251.22896-2-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: ltr501: Don't return error code in trigger handler

commit ef9d67fa72c1b149a420587e435a3e888bdbf74f upstream.

IIO trigger handlers need to return one of the irqreturn_t values.
Returning an error code is not supported.

The ltr501 interrupt handler gets this right for most error paths, but
there is one case where it returns the error code.

In addition for this particular case the trigger handler does not call
`iio_trigger_notify_done()`. Which when not done keeps the triggered
disabled forever.

Modify the code so that the function returns a valid irqreturn_t value as
well as calling `iio_trigger_notify_done()` on all exit paths.

Fixes: 2690be905123 ("iio: Add Lite-On ltr501 ambient light / proximity sensor driver")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211024171251.22896-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: mma8452: Fix trigger reference couting

commit cd0082235783f814241a1c9483fb89e405f4f892 upstream.

The mma8452 driver directly assigns a trigger to the struct iio_dev. The
IIO core when done using this trigger will call `iio_trigger_put()` to drop
the reference count by 1.

Without the matching `iio_trigger_get()` in the driver the reference count
can reach 0 too early, the trigger gets freed while still in use and a
use-after-free occurs.

Fix this by getting a reference to the trigger before assigning it to the
IIO device.

Fixes: ae6d9ce05691 ("iio: mma8452: Add support for interrupt driven triggers.")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211024092700.6844-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: stk3310: Don't return error code in interrupt handler

commit 8e1eeca5afa7ba84d885987165dbdc5decf15413 upstream.

Interrupt handlers must return one of the irqreturn_t values. Returning a
error code is not supported.

The stk3310 event interrupt handler returns an error code when reading the
flags register fails.

Fix the implementation to always return an irqreturn_t value.

Fixes: 3dd477acbdd1 ("iio: light: Add threshold interrupt support for STK3310")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211024171251.22896-3-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: trigger: stm32-timer: fix MODULE_ALIAS

commit 893621e0606747c5bbefcaf2794d12c7aa6212b7 upstream.

modprobe can't handle spaces in aliases.

Fixes: 93fbe91b5521 ("iio: Add STM32 timer trigger driver")
Signed-off-by: Alyssa Ross <hi@alyssa.is>
Link: https://lore.kernel.org/r/20211125182850.2645424-1-hi@alyssa.is
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: trigger: Fix reference counting

commit a827a4984664308f13599a0b26c77018176d0c7c upstream.

In viio_trigger_alloc() device_initialize() is used to set the initial
reference count of the trigger to 1. Then another get_device() is called on
trigger. This sets the reference count to 2 before the trigger is returned.

iio_trigger_free(), which is the matching API to viio_trigger_alloc(),
calls put_device() which decreases the reference count by 1. But the second
reference count acquired in viio_trigger_alloc() is never dropped.

As a result the iio_trigger_release() function is never called and the
memory associated with the trigger is never freed.

Since there is no reason for the trigger to start its lifetime with two
reference counts just remove the extra get_device() in
viio_trigger_alloc().

Fixes: 5f9c035cae18 ("staging:iio:triggers. Add a reference get to the core for triggers.")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20211024092700.6844-2-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: gyro: adxrs290: fix data signedness

commit fde272e78e004a45c7e4976876277d7e6a5a0ede upstream.

Properly sign-extend the rate and temperature data.

Fixes: 2c8920fff1457 ("iio: gyro: Add driver support for ADXRS290")
Signed-off-by: Kister Genesis Jimenez <kister.jimenez@analog.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211115104147.18669-1-nuno.sa@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci: avoid race between disable slot command and host runtime suspend

commit 7faac1953ed1f658f719cdf7bb7303fa5eef822c upstream.

Make xhci_disable_slot() synchronous, thus ensuring it, and
xhci_free_dev() calling it return after xHC controller completes
the disable slot command.

Otherwise the roothub and xHC host may runtime suspend, and clear the
command ring while the disable slot command is being processed.

This causes a command completion mismatch as the completion event can't
be mapped to the correct command.
Command ring gets out of sync and commands time out.
Driver finally assumes host is unresponsive and bails out.

usb 2-4: USB disconnect, device number 10
xhci_hcd 0000:00:0d.0: ERROR mismatched command completion event
...
xhci_hcd 0000:00:0d.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:00:0d.0: HC died; cleaning up

Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: core: config: using bit mask instead of individual bits

commit ca5737396927afd4d57b133fd2874bbcf3421cdb upstream.

Using standard USB_EP_MAXP_MULT_MASK instead of individual bits for
extracting multiple-transactions bits from wMaxPacketSize value.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Link: https://lore.kernel.org/r/20211210085219.16796-2-pavel.hofman@ivitera.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci: Remove CONFIG_USB_DEFAULT_PERSIST to prevent xHCI from runtime suspending

commit 811ae81320da53a5670c36970cefacca8519f90e upstream.

When the xHCI is quirked with XHCI_RESET_ON_RESUME, runtime resume
routine also resets the controller.

This is bad for USB drivers without reset_resume callback, because
there's no subsequent call of usb_dev_complete() ->
usb_resume_complete() to force rebinding the driver to the device. For
instance, btusb device stops working after xHCI controller is runtime
resumed, if the controlled is quirked with XHCI_RESET_ON_RESUME.

So always take XHCI_RESET_ON_RESUME into account to solve the issue.

Cc: <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: core: config: fix validation of wMaxPacketValue entries

commit 1a3910c80966e4a76b25ce812f6bea0ef1b1d530 upstream.

The checks performed by commit aed9d65ac327 ("USB: validate
wMaxPacketValue entries in endpoint descriptors") require that initial
value of the maxp variable contains both maximum packet size bits
(10..0) and multiple-transactions bits (12..11). However, the existing
code assings only the maximum packet size bits. This patch assigns all
bits of wMaxPacketSize to the variable.

Fixes: aed9d65ac327 ("USB: validate wMaxPacketValue entries in endpoint descriptors")
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Link: https://lore.kernel.org/r/20211210085219.16796-1-pavel.hofman@ivitera.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>