Robert-Ionut Alexa [Tue, 18 Oct 2022 14:18:59 +0000 (17:18 +0300)]
net: dpaa2-eth: AF_XDP RX zero copy support
This patch adds the support for receiving packets via the AF_XDP
zero-copy mechanism in the dpaa2-eth driver. The support is available
only on the LX2160A SoC and variants because we are relying on the HW
capability to associate a buffer pool to a specific queue (QDBIN), only
available on newer WRIOP versions.
On the control path, the dpaa2_xsk_enable_pool() function is responsible
to allocate a buffer pool (BP), setup this new BP to be used only on the
requested queue and change the consume function to point to the XSK ZC
one.
We are forced to call dev_close() in order to change the queue to buffer
pool association (dpaa2_xsk_set_bp_per_qdbin) . This also works in our
favor since at dev_close() the buffer pools will be drained and at the
later dev_open() call they will be again seeded, this time with buffers
allocated from the XSK pool if needed.
On the data path, a new software annotation type is defined to be used
only for the XSK scenarios. This will enable us to pass keep necessary
information about a packet buffer between the moment in which it was
seeded and when it's received by the driver. In the XSK case, we are
keeping the associated xdp_buff.
Depending on the action returned by the BPF program, we will do the
following:
- XDP_PASS: copy the contents of the packet into a brand new skb,
recycle the initial buffer.
- XDP_TX: just enqueue the same frame descriptor back into the Tx path,
the buffer will get automatically released into the initial BP.
- XDP_REDIRECT: call xdp_do_redirect() and exit.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert-Ionut Alexa [Tue, 18 Oct 2022 14:18:58 +0000 (17:18 +0300)]
net: dpaa2-eth: create and export the dpaa2_eth_receive_skb() function
Carve out code from the dpaa2_eth_rx() function in order to create and
export the dpaa2_eth_receive_skb() function. Do this in order to reuse
this code also from the XSK path which will be introduced in a later
patch.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert-Ionut Alexa [Tue, 18 Oct 2022 14:18:57 +0000 (17:18 +0300)]
net: dpaa2-eth: create and export the dpaa2_eth_alloc_skb function
The dpaa2_eth_alloc_skb() function is added by moving code from the
dpaa2_eth_copybreak() previously defined function. What the new API does
is to allocate a new skb, copy the frame data from the passed FD to the
new skb and then return the skb.
Export this new function since we'll need the this functionality also
from the XSK code path.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei [Tue, 18 Oct 2022 14:18:56 +0000 (17:18 +0300)]
net: dpaa2-eth: use dev_close/open instead of the internal functions
Instead of calling the internal functions which implement .ndo_stop and
.ndo_open, we can simply call dev_close and dev_open, so that we keep
the code cleaner.
Also, in the next patches we'll use the same APIs from other files
without needing to export the internal functions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert-Ionut Alexa [Tue, 18 Oct 2022 14:18:55 +0000 (17:18 +0300)]
net: dpaa2-eth: update the dpni_set_pools() API to support per QDBIN pools
Update the dpni_set_pool() firmware API so that in the next patches we
can configure per Rx queue (per QDBIN) buffer pools.
This is a hard requirement of the AF_XDP, thus we need the newer API
version.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei [Tue, 18 Oct 2022 14:18:54 +0000 (17:18 +0300)]
net: dpaa2-eth: export buffer pool info into a new debugfs file
Export the allocated buffer pools, the number of buffers that they have
currently and which channels are using which BP.
The output looks like below:
Buffer pool info for eth2:
IDX BPID Buf count CH#0 CH#1 CH#2 CH#3
BP#0 1 5124 x x x x
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei [Tue, 18 Oct 2022 14:18:53 +0000 (17:18 +0300)]
net: dpaa2-eth: export the CH#<index> in the 'ch_stats' debug file
Just give out an index for each channel that we export into the debug
file in the form of CH#<index>. This is purely to help corelate each
channel information from one debugfs file to another one.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert-Ionut Alexa [Tue, 18 Oct 2022 14:18:52 +0000 (17:18 +0300)]
net: dpaa2-eth: add support for multiple buffer pools per DPNI
This patch allows the configuration of multiple buffer pools associated
with a single DPNI object, each distinct DPBP object not necessarily
shared among all queues.
The user can interogate both the number of buffer pools and the buffer
count in each buffer pool by using the .get_ethtool_stats() callback.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei [Tue, 18 Oct 2022 14:18:51 +0000 (17:18 +0300)]
net: dpaa2-eth: rearrange variable in dpaa2_eth_get_ethtool_stats
Rearrange the variables in the dpaa2_eth_get_ethtool_stats() function so
that we adhere to the reverse Christmas tree rule.
Also, in the next patch we are adding more variables and I didn't know
where to place them with the current ordering.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert-Ionut Alexa [Tue, 18 Oct 2022 14:18:50 +0000 (17:18 +0300)]
net: dpaa2-eth: add support to query the number of queues through ethtool
The .get_channels() ethtool_ops callback is implemented and exports the
number of queues: Rx, Tx, Tx conf and Rx err.
The last two ones, Tx confirmation and Rx err, are counted as 'others'.
The .set_channels() callback is not implemented since the DPAA2
software/firmware architecture does not allow the dynamic
reconfiguration of the number of queues.
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandru Tachici [Wed, 19 Oct 2022 17:13:14 +0000 (20:13 +0300)]
dt-bindings: net: adin1110: Document reset
Document GPIO for HW reset.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandru Tachici [Wed, 19 Oct 2022 17:13:13 +0000 (20:13 +0300)]
net: ethernet: adi: adin1110: add reset GPIO
Add an optional GPIO to be used for a hardware reset of the IC.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Johnson [Tue, 18 Oct 2022 21:17:18 +0000 (14:17 -0700)]
net: ipa: Make QMI message rules const
Commit
ff6d365898d4 ("soc: qcom: qmi: use const for struct
qmi_elem_info") allows QMI message encoding/decoding rules to be
const, so do that for IPA.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doug Berger [Wed, 19 Oct 2022 21:51:23 +0000 (14:51 -0700)]
net: bcmgenet: add RX_CLS_LOC_ANY support
If a matching flow spec exists its current location is as good
as ANY. If not add the new flow spec at the first available
location.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221019215123.316997-1-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexey Kodanev [Wed, 19 Oct 2022 18:07:35 +0000 (21:07 +0300)]
sctp: remove unnecessary NULL checks in sctp_enqueue_event()
After commit
178ca044aa60 ("sctp: Make sctp_enqueue_event tak an
skb list."), skb_list cannot be NULL.
Detected using the static analysis tool - Svace.
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/20221019180735.161388-3-aleksei.kodanev@bell-sw.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexey Kodanev [Wed, 19 Oct 2022 18:07:34 +0000 (21:07 +0300)]
sctp: remove unnecessary NULL check in sctp_ulpq_tail_event()
After commit
013b96ec6461 ("sctp: Pass sk_buff_head explicitly to
sctp_ulpq_tail_event().") there is one more unneeded check of
skb_list for NULL.
Detected using the static analysis tool - Svace.
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/20221019180735.161388-2-aleksei.kodanev@bell-sw.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexey Kodanev [Wed, 19 Oct 2022 18:07:33 +0000 (21:07 +0300)]
sctp: remove unnecessary NULL check in sctp_association_init()
'&asoc->ulpq' passed to sctp_ulpq_init() as the first argument,
then sctp_qlpq_init() initializes it and eventually returns the
address of the struct member back. Therefore, in this case, the
return pointer cannot be NULL.
Moreover, it seems sctp_ulpq_init() has always been used only in
sctp_association_init(), so there's really no need to return ulpq
anymore.
Detected using the static analysis tool - Svace.
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/20221019180735.161388-1-aleksei.kodanev@bell-sw.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 21 Oct 2022 00:49:10 +0000 (17:49 -0700)]
Merge git://git./linux/kernel/git/netdev/net
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Fri, 21 Oct 2022 00:24:59 +0000 (17:24 -0700)]
Merge tag 'net-6.1-rc2' of git://git./linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter.
Current release - regressions:
- revert "net: fix cpu_max_bits_warn() usage in
netif_attrmask_next{,_and}"
- revert "net: sched: fq_codel: remove redundant resource cleanup in
fq_codel_init()"
- dsa: uninitialized variable in dsa_slave_netdevice_event()
- eth: sunhme: uninitialized variable in happy_meal_init()
Current release - new code bugs:
- eth: octeontx2: fix resource not freed after malloc
Previous releases - regressions:
- sched: fix return value of qdisc ingress handling on success
- sched: fix race condition in qdisc_graft()
- udp: update reuse->has_conns under reuseport_lock.
- tls: strp: make sure the TCP skbs do not have overlapping data
- hsr: avoid possible NULL deref in skb_clone()
- tipc: fix an information leak in tipc_topsrv_kern_subscr
- phylink: add mac_managed_pm in phylink_config structure
- eth: i40e: fix DMA mappings leak
- eth: hyperv: fix a RX-path warning
- eth: mtk: fix memory leaks
Previous releases - always broken:
- sched: cake: fix null pointer access issue when cake_init() fails"
* tag 'net-6.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (43 commits)
net: phy: dp83822: disable MDI crossover status change interrupt
net: sched: fix race condition in qdisc_graft()
net: hns: fix possible memory leak in hnae_ae_register()
wwan_hwsim: fix possible memory leak in wwan_hwsim_dev_new()
sfc: include vport_id in filter spec hash and equal()
genetlink: fix kdoc warnings
selftests: add selftest for chaining of tc ingress handling to egress
net: Fix return value of qdisc ingress handling on success
net: sched: sfb: fix null pointer access issue when sfb_init() fails
Revert "net: sched: fq_codel: remove redundant resource cleanup in fq_codel_init()"
net: sched: cake: fix null pointer access issue when cake_init() fails
ethernet: marvell: octeontx2 Fix resource not freed after malloc
netfilter: nf_tables: relax NFTA_SET_ELEM_KEY_END set flags requirements
netfilter: rpfilter/fib: Set ->flowic_uid correctly for user namespaces.
ionic: catch NULL pointer issue on reconfig
net: hsr: avoid possible NULL deref in skb_clone()
bnxt_en: fix memory leak in bnxt_nvm_test()
ip6mr: fix UAF issue in ip6mr_sk_done() when addrconf_init_net() failed
udp: Update reuse->has_conns under reuseport_lock.
net: ethernet: mediatek: ppe: Remove the unused function mtk_foe_entry_usable()
...
Linus Torvalds [Fri, 21 Oct 2022 00:07:54 +0000 (17:07 -0700)]
Merge tag 'ata-6.1-rc2' of git://git./linux/kernel/git/dlemoal/libata
Pull ata fixes from Damien Le Moal:
"Several minor fixes:
- Fix the module alias for the ahci_imx driver to get autoloading to
work (Alexander)
- Fix a potential array-index-out-of-bounds problem with the
enclosure managment support in the ahci driver (Kai-Heng)
- Several patches to fix compilation warnings thrown by clang in the
ahci_st, sata_rcar, ahci_brcm, ahci_xgene, ahci_imx and ahci_qoriq
drivers (me)"
* tag 'ata-6.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: ahci_qoriq: Fix compilation warning
ata: ahci_imx: Fix compilation warning
ata: ahci_xgene: Fix compilation warning
ata: ahci_brcm: Fix compilation warning
ata: sata_rcar: Fix compilation warning
ata: ahci_st: Fix compilation warning
ata: ahci: Match EM_MAX_SLOTS with SATA_PMP_MAX_PORTS
ata: ahci-imx: Fix MODULE_ALIAS
Linus Torvalds [Fri, 21 Oct 2022 00:00:54 +0000 (17:00 -0700)]
Merge tag 'for-6.1/dm-changes-v2' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- Fix dm-bufio to use test_bit_acquire to properly test_bit on arches
with weaker memory ordering.
- DM core replace DMWARN with DMERR or DMCRIT for fatal errors.
- Enable WQ_HIGHPRI on DM verity target's verify_wq.
- Add documentation for DM verity's try_verify_in_tasklet option.
- Various typo and redundant word fixes in code and/or comments.
* tag 'for-6.1/dm-changes-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm clone: Fix typo in block_device format specifier
dm: remove unnecessary assignment statement in alloc_dev()
dm verity: Add documentation for try_verify_in_tasklet option
dm cache: delete the redundant word 'each' in comment
dm raid: fix typo in analyse_superblocks code comment
dm verity: enable WQ_HIGHPRI on verify_wq
dm raid: delete the redundant word 'that' in comment
dm: change from DMWARN to DMERR or DMCRIT for fatal errors
dm bufio: use the acquire memory barrier when testing for B_READING
Kees Cook [Tue, 18 Oct 2022 09:28:27 +0000 (02:28 -0700)]
net: ipa: Proactively round up to kmalloc bucket size
Instead of discovering the kmalloc bucket size _after_ allocation, round
up proactively so the allocation is explicitly made for the full size,
allowing the compiler to correctly reason about the resulting size of
the buffer through the existing __alloc_size() hint.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Reviewed-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/lkml/4d75a9fd-1b94-7208-9de8-5a0102223e68@ieee.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221018092724.give.735-kees@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Felix Riemann [Tue, 18 Oct 2022 10:47:54 +0000 (12:47 +0200)]
net: phy: dp83822: disable MDI crossover status change interrupt
If the cable is disconnected the PHY seems to toggle between MDI and
MDI-X modes. With the MDI crossover status interrupt active this causes
roughly 10 interrupts per second.
As the crossover status isn't checked by the driver, the interrupt can
be disabled to reduce the interrupt load.
Fixes:
87461f7a58ab ("net: phy: DP83822 initial driver submission")
Signed-off-by: Felix Riemann <felix.riemann@sma.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221018104755.30025-1-svc.sw.rte.linux@sma.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Tue, 18 Oct 2022 20:32:58 +0000 (20:32 +0000)]
net: sched: fix race condition in qdisc_graft()
We had one syzbot report [1] in syzbot queue for a while.
I was waiting for more occurrences and/or a repro but
Dmitry Vyukov spotted the issue right away.
<quoting Dmitry>
qdisc_graft() drops reference to qdisc in notify_and_destroy
while it's still assigned to dev->qdisc
</quoting>
Indeed, RCU rules are clear when replacing a data structure.
The visible pointer (dev->qdisc in this case) must be updated
to the new object _before_ RCU grace period is started
(qdisc_put(old) in this case).
[1]
BUG: KASAN: use-after-free in __tcf_qdisc_find.part.0+0xa3a/0xac0 net/sched/cls_api.c:1066
Read of size 4 at addr
ffff88802065e038 by task syz-executor.4/21027
CPU: 0 PID: 21027 Comm: syz-executor.4 Not tainted 6.0.0-rc3-syzkaller-00363-g7726d4c3e60b #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/26/2022
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:317 [inline]
print_report.cold+0x2ba/0x719 mm/kasan/report.c:433
kasan_report+0xb1/0x1e0 mm/kasan/report.c:495
__tcf_qdisc_find.part.0+0xa3a/0xac0 net/sched/cls_api.c:1066
__tcf_qdisc_find net/sched/cls_api.c:1051 [inline]
tc_new_tfilter+0x34f/0x2200 net/sched/cls_api.c:2018
rtnetlink_rcv_msg+0x955/0xca0 net/core/rtnetlink.c:6081
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2501
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x543/0x7f0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x917/0xe10 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:734
____sys_sendmsg+0x6eb/0x810 net/socket.c:2482
___sys_sendmsg+0x110/0x1b0 net/socket.c:2536
__sys_sendmsg+0xf3/0x1c0 net/socket.c:2565
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7f5efaa89279
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:
00007f5efbc31168 EFLAGS:
00000246 ORIG_RAX:
000000000000002e
RAX:
ffffffffffffffda RBX:
00007f5efab9bf80 RCX:
00007f5efaa89279
RDX:
0000000000000000 RSI:
0000000020000140 RDI:
0000000000000005
RBP:
00007f5efaae32e9 R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000246 R12:
0000000000000000
R13:
00007f5efb0cfb1f R14:
00007f5efbc31300 R15:
0000000000022000
</TASK>
Allocated by task 21027:
kasan_save_stack+0x1e/0x40 mm/kasan/common.c:38
kasan_set_track mm/kasan/common.c:45 [inline]
set_alloc_info mm/kasan/common.c:437 [inline]
____kasan_kmalloc mm/kasan/common.c:516 [inline]
____kasan_kmalloc mm/kasan/common.c:475 [inline]
__kasan_kmalloc+0xa9/0xd0 mm/kasan/common.c:525
kmalloc_node include/linux/slab.h:623 [inline]
kzalloc_node include/linux/slab.h:744 [inline]
qdisc_alloc+0xb0/0xc50 net/sched/sch_generic.c:938
qdisc_create_dflt+0x71/0x4a0 net/sched/sch_generic.c:997
attach_one_default_qdisc net/sched/sch_generic.c:1152 [inline]
netdev_for_each_tx_queue include/linux/netdevice.h:2437 [inline]
attach_default_qdiscs net/sched/sch_generic.c:1170 [inline]
dev_activate+0x760/0xcd0 net/sched/sch_generic.c:1229
__dev_open+0x393/0x4d0 net/core/dev.c:1441
__dev_change_flags+0x583/0x750 net/core/dev.c:8556
rtnl_configure_link+0xee/0x240 net/core/rtnetlink.c:3189
rtnl_newlink_create net/core/rtnetlink.c:3371 [inline]
__rtnl_newlink+0x10b8/0x17e0 net/core/rtnetlink.c:3580
rtnl_newlink+0x64/0xa0 net/core/rtnetlink.c:3593
rtnetlink_rcv_msg+0x43a/0xca0 net/core/rtnetlink.c:6090
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2501
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x543/0x7f0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x917/0xe10 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:734
____sys_sendmsg+0x6eb/0x810 net/socket.c:2482
___sys_sendmsg+0x110/0x1b0 net/socket.c:2536
__sys_sendmsg+0xf3/0x1c0 net/socket.c:2565
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Freed by task 21020:
kasan_save_stack+0x1e/0x40 mm/kasan/common.c:38
kasan_set_track+0x21/0x30 mm/kasan/common.c:45
kasan_set_free_info+0x20/0x30 mm/kasan/generic.c:370
____kasan_slab_free mm/kasan/common.c:367 [inline]
____kasan_slab_free+0x166/0x1c0 mm/kasan/common.c:329
kasan_slab_free include/linux/kasan.h:200 [inline]
slab_free_hook mm/slub.c:1754 [inline]
slab_free_freelist_hook+0x8b/0x1c0 mm/slub.c:1780
slab_free mm/slub.c:3534 [inline]
kfree+0xe2/0x580 mm/slub.c:4562
rcu_do_batch kernel/rcu/tree.c:2245 [inline]
rcu_core+0x7b5/0x1890 kernel/rcu/tree.c:2505
__do_softirq+0x1d3/0x9c6 kernel/softirq.c:571
Last potentially related work creation:
kasan_save_stack+0x1e/0x40 mm/kasan/common.c:38
__kasan_record_aux_stack+0xbe/0xd0 mm/kasan/generic.c:348
call_rcu+0x99/0x790 kernel/rcu/tree.c:2793
qdisc_put+0xcd/0xe0 net/sched/sch_generic.c:1083
notify_and_destroy net/sched/sch_api.c:1012 [inline]
qdisc_graft+0xeb1/0x1270 net/sched/sch_api.c:1084
tc_modify_qdisc+0xbb7/0x1a00 net/sched/sch_api.c:1671
rtnetlink_rcv_msg+0x43a/0xca0 net/core/rtnetlink.c:6090
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2501
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x543/0x7f0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x917/0xe10 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:734
____sys_sendmsg+0x6eb/0x810 net/socket.c:2482
___sys_sendmsg+0x110/0x1b0 net/socket.c:2536
__sys_sendmsg+0xf3/0x1c0 net/socket.c:2565
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Second to last potentially related work creation:
kasan_save_stack+0x1e/0x40 mm/kasan/common.c:38
__kasan_record_aux_stack+0xbe/0xd0 mm/kasan/generic.c:348
kvfree_call_rcu+0x74/0x940 kernel/rcu/tree.c:3322
neigh_destroy+0x431/0x630 net/core/neighbour.c:912
neigh_release include/net/neighbour.h:454 [inline]
neigh_cleanup_and_release+0x1f8/0x330 net/core/neighbour.c:103
neigh_del net/core/neighbour.c:225 [inline]
neigh_remove_one+0x37d/0x460 net/core/neighbour.c:246
neigh_forced_gc net/core/neighbour.c:276 [inline]
neigh_alloc net/core/neighbour.c:447 [inline]
___neigh_create+0x18b5/0x29a0 net/core/neighbour.c:642
ip6_finish_output2+0xfb8/0x1520 net/ipv6/ip6_output.c:125
__ip6_finish_output net/ipv6/ip6_output.c:195 [inline]
ip6_finish_output+0x690/0x1160 net/ipv6/ip6_output.c:206
NF_HOOK_COND include/linux/netfilter.h:296 [inline]
ip6_output+0x1ed/0x540 net/ipv6/ip6_output.c:227
dst_output include/net/dst.h:451 [inline]
NF_HOOK include/linux/netfilter.h:307 [inline]
NF_HOOK include/linux/netfilter.h:301 [inline]
mld_sendpack+0xa09/0xe70 net/ipv6/mcast.c:1820
mld_send_cr net/ipv6/mcast.c:2121 [inline]
mld_ifc_work+0x71c/0xdc0 net/ipv6/mcast.c:2653
process_one_work+0x991/0x1610 kernel/workqueue.c:2289
worker_thread+0x665/0x1080 kernel/workqueue.c:2436
kthread+0x2e4/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306
The buggy address belongs to the object at
ffff88802065e000
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 56 bytes inside of
1024-byte region [
ffff88802065e000,
ffff88802065e400)
The buggy address belongs to the physical page:
page:
ffffea0000819600 refcount:1 mapcount:0 mapping:
0000000000000000 index:0x0 pfn:0x20658
head:
ffffea0000819600 order:3 compound_mapcount:0 compound_pincount:0
flags: 0xfff00000010200(slab|head|node=0|zone=1|lastcpupid=0x7ff)
raw:
00fff00000010200 0000000000000000 dead000000000001 ffff888011841dc0
raw:
0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
page_owner tracks the page as allocated
page last allocated via order 3, migratetype Unmovable, gfp_mask 0xd20c0(__GFP_IO|__GFP_FS|__GFP_NOWARN|__GFP_NORETRY|__GFP_COMP|__GFP_NOMEMALLOC), pid 3523, tgid 3523 (sshd), ts
41495190986, free_ts
41417713212
prep_new_page mm/page_alloc.c:2532 [inline]
get_page_from_freelist+0x109b/0x2ce0 mm/page_alloc.c:4283
__alloc_pages+0x1c7/0x510 mm/page_alloc.c:5515
alloc_pages+0x1a6/0x270 mm/mempolicy.c:2270
alloc_slab_page mm/slub.c:1824 [inline]
allocate_slab+0x27e/0x3d0 mm/slub.c:1969
new_slab mm/slub.c:2029 [inline]
___slab_alloc+0x7f1/0xe10 mm/slub.c:3031
__slab_alloc.constprop.0+0x4d/0xa0 mm/slub.c:3118
slab_alloc_node mm/slub.c:3209 [inline]
__kmalloc_node_track_caller+0x2f2/0x380 mm/slub.c:4955
kmalloc_reserve net/core/skbuff.c:358 [inline]
__alloc_skb+0xd9/0x2f0 net/core/skbuff.c:430
alloc_skb_fclone include/linux/skbuff.h:1307 [inline]
tcp_stream_alloc_skb+0x38/0x580 net/ipv4/tcp.c:861
tcp_sendmsg_locked+0xc36/0x2f80 net/ipv4/tcp.c:1325
tcp_sendmsg+0x2b/0x40 net/ipv4/tcp.c:1483
inet_sendmsg+0x99/0xe0 net/ipv4/af_inet.c:819
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:734
sock_write_iter+0x291/0x3d0 net/socket.c:1108
call_write_iter include/linux/fs.h:2187 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x9e9/0xdd0 fs/read_write.c:578
ksys_write+0x1e8/0x250 fs/read_write.c:631
page last free stack trace:
reset_page_owner include/linux/page_owner.h:24 [inline]
free_pages_prepare mm/page_alloc.c:1449 [inline]
free_pcp_prepare+0x5e4/0xd20 mm/page_alloc.c:1499
free_unref_page_prepare mm/page_alloc.c:3380 [inline]
free_unref_page+0x19/0x4d0 mm/page_alloc.c:3476
__unfreeze_partials+0x17c/0x1a0 mm/slub.c:2548
qlink_free mm/kasan/quarantine.c:168 [inline]
qlist_free_all+0x6a/0x170 mm/kasan/quarantine.c:187
kasan_quarantine_reduce+0x180/0x200 mm/kasan/quarantine.c:294
__kasan_slab_alloc+0xa2/0xc0 mm/kasan/common.c:447
kasan_slab_alloc include/linux/kasan.h:224 [inline]
slab_post_alloc_hook mm/slab.h:727 [inline]
slab_alloc_node mm/slub.c:3243 [inline]
slab_alloc mm/slub.c:3251 [inline]
__kmem_cache_alloc_lru mm/slub.c:3258 [inline]
kmem_cache_alloc+0x267/0x3b0 mm/slub.c:3268
kmem_cache_zalloc include/linux/slab.h:723 [inline]
alloc_buffer_head+0x20/0x140 fs/buffer.c:2974
alloc_page_buffers+0x280/0x790 fs/buffer.c:829
create_empty_buffers+0x2c/0xee0 fs/buffer.c:1558
ext4_block_write_begin+0x1004/0x1530 fs/ext4/inode.c:1074
ext4_da_write_begin+0x422/0xae0 fs/ext4/inode.c:2996
generic_perform_write+0x246/0x560 mm/filemap.c:3738
ext4_buffered_write_iter+0x15b/0x460 fs/ext4/file.c:270
ext4_file_write_iter+0x44a/0x1660 fs/ext4/file.c:679
call_write_iter include/linux/fs.h:2187 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x9e9/0xdd0 fs/read_write.c:578
Fixes:
af356afa010f ("net_sched: reintroduce dev->qdisc for use by sch_api")
Reported-by: syzbot <syzkaller@googlegroups.com>
Diagnosed-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221018203258.2793282-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yang Yingliang [Tue, 18 Oct 2022 12:24:51 +0000 (20:24 +0800)]
net: hns: fix possible memory leak in hnae_ae_register()
Inject fault while probing module, if device_register() fails,
but the refcount of kobject is not decreased to 0, the name
allocated in dev_set_name() is leaked. Fix this by calling
put_device(), so that name can be freed in callback function
kobject_cleanup().
unreferenced object 0xffff00c01aba2100 (size 128):
comm "systemd-udevd", pid 1259, jiffies
4294903284 (age 294.152s)
hex dump (first 32 bytes):
68 6e 61 65 30 00 00 00 18 21 ba 1a c0 00 ff ff hnae0....!......
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<
0000000034783f26>] slab_post_alloc_hook+0xa0/0x3e0
[<
00000000748188f2>] __kmem_cache_alloc_node+0x164/0x2b0
[<
00000000ab0743e8>] __kmalloc_node_track_caller+0x6c/0x390
[<
000000006c0ffb13>] kvasprintf+0x8c/0x118
[<
00000000fa27bfe1>] kvasprintf_const+0x60/0xc8
[<
0000000083e10ed7>] kobject_set_name_vargs+0x3c/0xc0
[<
000000000b87affc>] dev_set_name+0x7c/0xa0
[<
000000003fd8fe26>] hnae_ae_register+0xcc/0x190 [hnae]
[<
00000000fe97edc9>] hns_dsaf_ae_init+0x9c/0x108 [hns_dsaf]
[<
00000000c36ff1eb>] hns_dsaf_probe+0x548/0x748 [hns_dsaf]
Fixes:
6fe6611ff275 ("net: add Hisilicon Network Subsystem hnae framework support")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221018122451.1749171-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yang Yingliang [Tue, 18 Oct 2022 13:16:07 +0000 (21:16 +0800)]
wwan_hwsim: fix possible memory leak in wwan_hwsim_dev_new()
Inject fault while probing module, if device_register() fails,
but the refcount of kobject is not decreased to 0, the name
allocated in dev_set_name() is leaked. Fix this by calling
put_device(), so that name can be freed in callback function
kobject_cleanup().
unreferenced object 0xffff88810152ad20 (size 8):
comm "modprobe", pid 252, jiffies
4294849206 (age 22.713s)
hex dump (first 8 bytes):
68 77 73 69 6d 30 00 ff hwsim0..
backtrace:
[<
000000009c3504ed>] __kmalloc_node_track_caller+0x44/0x1b0
[<
00000000c0228a5e>] kvasprintf+0xb5/0x140
[<
00000000cff8c21f>] kvasprintf_const+0x55/0x180
[<
0000000055a1e073>] kobject_set_name_vargs+0x56/0x150
[<
000000000a80b139>] dev_set_name+0xab/0xe0
Fixes:
f36a111a74e7 ("wwan_hwsim: WWAN device simulator")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Link: https://lore.kernel.org/r/20221018131607.1901641-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pieter Jansen van Vuuren [Tue, 18 Oct 2022 09:28:41 +0000 (10:28 +0100)]
sfc: include vport_id in filter spec hash and equal()
Filters on different vports are qualified by different implicit MACs and/or
VLANs, so shouldn't be considered equal even if their other match fields
are identical.
Fixes:
7c460d9be610 ("sfc: Extend and abstract efx_filter_spec to cover Huntington/EF10")
Co-developed-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20221018092841.32206-1-pieter.jansen-van-vuuren@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kees Cook [Tue, 18 Oct 2022 09:06:33 +0000 (02:06 -0700)]
openvswitch: Use kmalloc_size_roundup() to match ksize() usage
Round up allocations with kmalloc_size_roundup() so that openvswitch's
use of ksize() is always accurate and no special handling of the memory
is needed by KASAN, UBSAN_BOUNDS, nor FORTIFY_SOURCE.
Cc: Pravin B Shelar <pshelar@ovn.org>
Cc: dev@openvswitch.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221018090628.never.537-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 19 Oct 2022 22:45:54 +0000 (15:45 -0700)]
Merge git://git./linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Missing flowi uid field in nft_fib expression, from Guillaume Nault.
This is broken since the creation of the fib expression.
2) Relax sanity check to fix bogus EINVAL error when deleting elements
belonging set intervals. Broken since 6.0-rc.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: relax NFTA_SET_ELEM_KEY_END set flags requirements
netfilter: rpfilter/fib: Set ->flowic_uid correctly for user namespaces.
====================
Link: https://lore.kernel.org/r/20221019065225.1006344-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 18 Oct 2022 23:13:10 +0000 (16:13 -0700)]
genetlink: fix kdoc warnings
Address a bunch of kdoc warnings:
include/net/genetlink.h:81: warning: Function parameter or member 'module' not described in 'genl_family'
include/net/genetlink.h:243: warning: expecting prototype for struct genl_info. Prototype was for struct genl_dumpit_info instead
include/net/genetlink.h:419: warning: Function parameter or member 'net' not described in 'genlmsg_unicast'
include/net/genetlink.h:438: warning: expecting prototype for gennlmsg_data(). Prototype was for genlmsg_data() instead
include/net/genetlink.h:244: warning: Function parameter or member 'op' not described in 'genl_dumpit_info'
Link: https://lore.kernel.org/r/20221018231310.1040482-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 19 Oct 2022 20:00:09 +0000 (13:00 -0700)]
Merge branch 'netlink-formatted-extacks'
Edward Cree says:
====================
netlink: formatted extacks
Currently, netlink extacks can only carry fixed string messages, which
is limiting when reporting failures in complex systems. This series
adds the ability to return printf-formatted messages, and uses it in
the sfc driver's TC offload code.
Formatted extack messages are limited in length to a fixed buffer size,
currently 80 characters. If the message exceeds this, the full message
will be logged (ratelimited) to the console and a truncated version
returned over netlink.
There is no change to the netlink uAPI; only internal kernel changes
are needed.
====================
Link: https://lore.kernel.org/r/cover.1666102698.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Edward Cree [Tue, 18 Oct 2022 14:37:29 +0000 (15:37 +0100)]
sfc: remove 'log-tc-errors' ethtool private flag
It no longer does anything now that we're using formatted extacks instead.
So we can remove the driver's whole get/set priv_flags implementation.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Edward Cree [Tue, 18 Oct 2022 14:37:28 +0000 (15:37 +0100)]
sfc: use formatted extacks instead of efx_tc_err()
Since we can now get a formatted message back to the user with
NL_SET_ERR_MSG_FMT_MOD(), there's no need for our special logging.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Edward Cree [Tue, 18 Oct 2022 14:37:27 +0000 (15:37 +0100)]
netlink: add support for formatted extack messages
Include an 80-byte buffer in struct netlink_ext_ack that can be used
for scnprintf()ed messages. This does mean that the resulting string
can't be enumerated, translated etc. in the way NL_SET_ERR_MSG() was
designed to allow.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexandru Tachici [Mon, 17 Oct 2022 16:37:03 +0000 (19:37 +0300)]
net: ethernet: adi: adin1110: Fix SPI transfers
No need to use more than one SPI transfer for reads.
Use only one from now as ADIN1110/2111 does not tolerate
CS changes during reads.
The BCM2711/2708 SPI controllers worked fine, but the NXP
IMX8MM could not keep CS lowered during SPI bursts.
This change aims to make the ADIN1110/2111 driver compatible
with both SPI controllers, without any loss of bandwidth/other
capabilities.
Fixes:
bc93e19d088b ("net: ethernet: adi: Add ADIN1110 support")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 19 Oct 2022 13:04:36 +0000 (14:04 +0100)]
Merge branch 'qdisc-ingress-success'
Paul Blakey says:
====================
net: Fix return value of qdisc ingress handling on success
Fix patch + self-test with the currently broken scenario.
v4->v3:
Removed new line in self test and rebase (Paolo).
v2->v3:
Added DROP return to TC_ACT_SHOT case (Cong).
v1->v2:
Changed blamed commit
Added self-test
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey [Tue, 18 Oct 2022 07:34:39 +0000 (10:34 +0300)]
selftests: add selftest for chaining of tc ingress handling to egress
This test runs a simple ingress tc setup between two veth pairs,
then adds a egress->ingress rule to test the chaining of tc ingress
pipeline to tc egress piepline.
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey [Tue, 18 Oct 2022 07:34:38 +0000 (10:34 +0300)]
net: Fix return value of qdisc ingress handling on success
Currently qdisc ingress handling (sch_handle_ingress()) doesn't
set a return value and it is left to the old return value of
the caller (__netif_receive_skb_core()) which is RX drop, so if
the packet is consumed, caller will stop and return this value
as if the packet was dropped.
This causes a problem in the kernel tcp stack when having a
egress tc rule forwarding to a ingress tc rule.
The tcp stack sending packets on the device having the egress rule
will see the packets as not successfully transmitted (although they
actually were), will not advance it's internal state of sent data,
and packets returning on such tcp stream will be dropped by the tcp
stack with reason ack-of-unsent-data. See reproduction in [0] below.
Fix that by setting the return value to RX success if
the packet was handled successfully.
[0] Reproduction steps:
$ ip link add veth1 type veth peer name peer1
$ ip link add veth2 type veth peer name peer2
$ ifconfig peer1 5.5.5.6/24 up
$ ip netns add ns0
$ ip link set dev peer2 netns ns0
$ ip netns exec ns0 ifconfig peer2 5.5.5.5/24 up
$ ifconfig veth2 0 up
$ ifconfig veth1 0 up
#ingress forwarding veth1 <-> veth2
$ tc qdisc add dev veth2 ingress
$ tc qdisc add dev veth1 ingress
$ tc filter add dev veth2 ingress prio 1 proto all flower \
action mirred egress redirect dev veth1
$ tc filter add dev veth1 ingress prio 1 proto all flower \
action mirred egress redirect dev veth2
#steal packet from peer1 egress to veth2 ingress, bypassing the veth pipe
$ tc qdisc add dev peer1 clsact
$ tc filter add dev peer1 egress prio 20 proto ip flower \
action mirred ingress redirect dev veth1
#run iperf and see connection not running
$ iperf3 -s&
$ ip netns exec ns0 iperf3 -c 5.5.5.6 -i 1
#delete egress rule, and run again, now should work
$ tc filter del dev peer1 egress
$ ip netns exec ns0 iperf3 -c 5.5.5.6 -i 1
Fixes:
f697c3e8b35c ("[NET]: Avoid unnecessary cloning for ingress filtering")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 19 Oct 2022 13:01:08 +0000 (14:01 +0100)]
Merge branch 'net-bridge-mc-cleanups'
Ido Schimmel says:
====================
bridge: A few multicast cleanups
Clean up a few issues spotted while working on the bridge multicast code
and running its selftests.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 18 Oct 2022 06:40:01 +0000 (09:40 +0300)]
bridge: mcast: Simplify MDB entry creation
Before creating a new MDB entry, br_multicast_new_group() will call
br_mdb_ip_get() to see if one exists and return it if so.
Therefore, simply call br_multicast_new_group() and omit the call to
br_mdb_ip_get().
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 18 Oct 2022 06:40:00 +0000 (09:40 +0300)]
bridge: mcast: Use spin_lock() instead of spin_lock_bh()
IGMPv3 / MLDv2 Membership Reports are only processed from the data path
with softIRQ disabled, so there is no need to call spin_lock_bh(). Use
spin_lock() instead.
This is consistent with how other IGMP / MLD packets are processed.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 18 Oct 2022 06:39:59 +0000 (09:39 +0300)]
selftests: bridge_igmp: Remove unnecessary address deletion
The test group address is added and removed in v2reportleave_test().
There is no need to delete it again during cleanup as it results in the
following error message:
# bash -x ./bridge_igmp.sh
[...]
+ cleanup
+ pre_cleanup
[...]
+ ip address del dev swp4 239.10.10.10/32
RTNETLINK answers: Cannot assign requested address
+ h2_destroy
Solve by removing the unnecessary address deletion.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 18 Oct 2022 06:39:58 +0000 (09:39 +0300)]
selftests: bridge_vlan_mcast: Delete qdiscs during cleanup
The qdiscs are added during setup, but not deleted during cleanup,
resulting in the following error messages:
# ./bridge_vlan_mcast.sh
[...]
# ./bridge_vlan_mcast.sh
Error: Exclusivity flag on, cannot modify.
Error: Exclusivity flag on, cannot modify.
Solve by deleting the qdiscs during cleanup.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 19 Oct 2022 12:47:09 +0000 (13:47 +0100)]
Merge branch 'qdisc-null-deref'
Zhengchao Shao says:
====================
net: fix null pointer access issue in qdisc
These three patches fix the same type of problem. Set the default qdisc,
and then construct an init failure scenario when the dev qdisc is
configured on mqprio to trigger the reset process. NULL pointer access
may occur during the reset process.
---
v2: for fq_codel, revert the patch
---
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhengchao Shao [Tue, 18 Oct 2022 06:32:01 +0000 (14:32 +0800)]
net: sched: sfb: fix null pointer access issue when sfb_init() fails
When the default qdisc is sfb, if the qdisc of dev_queue fails to be
inited during mqprio_init(), sfb_reset() is invoked to clear resources.
In this case, the q->qdisc is NULL, and it will cause gpf issue.
The process is as follows:
qdisc_create_dflt()
sfb_init()
tcf_block_get() --->failed, q->qdisc is NULL
...
qdisc_put()
...
sfb_reset()
qdisc_reset(q->qdisc) --->q->qdisc is NULL
ops = qdisc->ops
The following is the Call Trace information:
general protection fault, probably for non-canonical address
0xdffffc0000000003: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000018-0x000000000000001f]
RIP: 0010:qdisc_reset+0x2b/0x6f0
Call Trace:
<TASK>
sfb_reset+0x37/0xd0
qdisc_reset+0xed/0x6f0
qdisc_destroy+0x82/0x4c0
qdisc_put+0x9e/0xb0
qdisc_create_dflt+0x2c3/0x4a0
mqprio_init+0xa71/0x1760
qdisc_create+0x3eb/0x1000
tc_modify_qdisc+0x408/0x1720
rtnetlink_rcv_msg+0x38e/0xac0
netlink_rcv_skb+0x12d/0x3a0
netlink_unicast+0x4a2/0x740
netlink_sendmsg+0x826/0xcc0
sock_sendmsg+0xc5/0x100
____sys_sendmsg+0x583/0x690
___sys_sendmsg+0xe8/0x160
__sys_sendmsg+0xbf/0x160
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x7f2164122d04
</TASK>
Fixes:
e13e02a3c68d ("net_sched: SFB flow scheduler")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhengchao Shao [Tue, 18 Oct 2022 06:32:00 +0000 (14:32 +0800)]
Revert "net: sched: fq_codel: remove redundant resource cleanup in fq_codel_init()"
This reverts commit
494f5063b86cd6e972cb41a27e083c9a3664319d.
When the default qdisc is fq_codel, if the qdisc of dev_queue fails to be
inited during mqprio_init(), fq_codel_reset() is invoked to clear
resources. In this case, the flow is NULL, and it will cause gpf issue.
The process is as follows:
qdisc_create_dflt()
fq_codel_init()
...
q->flows_cnt = 1024;
...
q->flows = kvcalloc(...) --->failed, q->flows is NULL
...
qdisc_put()
...
fq_codel_reset()
...
flow = q->flows + i --->q->flows is NULL
The following is the Call Trace information:
general protection fault, probably for non-canonical address
0xdffffc0000000001: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
RIP: 0010:fq_codel_reset+0x14d/0x350
Call Trace:
<TASK>
qdisc_reset+0xed/0x6f0
qdisc_destroy+0x82/0x4c0
qdisc_put+0x9e/0xb0
qdisc_create_dflt+0x2c3/0x4a0
mqprio_init+0xa71/0x1760
qdisc_create+0x3eb/0x1000
tc_modify_qdisc+0x408/0x1720
rtnetlink_rcv_msg+0x38e/0xac0
netlink_rcv_skb+0x12d/0x3a0
netlink_unicast+0x4a2/0x740
netlink_sendmsg+0x826/0xcc0
sock_sendmsg+0xc5/0x100
____sys_sendmsg+0x583/0x690
___sys_sendmsg+0xe8/0x160
__sys_sendmsg+0xbf/0x160
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x7fd272b22d04
</TASK>
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhengchao Shao [Tue, 18 Oct 2022 06:31:59 +0000 (14:31 +0800)]
net: sched: cake: fix null pointer access issue when cake_init() fails
When the default qdisc is cake, if the qdisc of dev_queue fails to be
inited during mqprio_init(), cake_reset() is invoked to clear
resources. In this case, the tins is NULL, and it will cause gpf issue.
The process is as follows:
qdisc_create_dflt()
cake_init()
q->tins = kvcalloc(...) --->failed, q->tins is NULL
...
qdisc_put()
...
cake_reset()
...
cake_dequeue_one()
b = &q->tins[...] --->q->tins is NULL
The following is the Call Trace information:
general protection fault, probably for non-canonical address
0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:cake_dequeue_one+0xc9/0x3c0
Call Trace:
<TASK>
cake_reset+0xb1/0x140
qdisc_reset+0xed/0x6f0
qdisc_destroy+0x82/0x4c0
qdisc_put+0x9e/0xb0
qdisc_create_dflt+0x2c3/0x4a0
mqprio_init+0xa71/0x1760
qdisc_create+0x3eb/0x1000
tc_modify_qdisc+0x408/0x1720
rtnetlink_rcv_msg+0x38e/0xac0
netlink_rcv_skb+0x12d/0x3a0
netlink_unicast+0x4a2/0x740
netlink_sendmsg+0x826/0xcc0
sock_sendmsg+0xc5/0x100
____sys_sendmsg+0x583/0x690
___sys_sendmsg+0xe8/0x160
__sys_sendmsg+0xbf/0x160
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x7f89e5122d04
</TASK>
Fixes:
046f6fd5daef ("sched: Add Common Applications Kept Enhanced (cake) qdisc")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manank Patel [Tue, 18 Oct 2022 05:33:18 +0000 (11:03 +0530)]
ethernet: marvell: octeontx2 Fix resource not freed after malloc
fix rxsc and txsc not getting freed before going out of scope
Fixes:
c54ffc73601c ("octeontx2-pf: mcs: Introduce MACSEC hardware offloading")
Signed-off-by: Manank Patel <pmanank200502@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 19 Oct 2022 12:25:09 +0000 (13:25 +0100)]
Merge branch 'dpaa-phylink'
Sean Anderson says:
====================
net: dpaa: Convert to phylink
This series converts the DPAA driver to phylink.
I have tried to maintain backwards compatibility with existing device
trees whereever possible. However, one area where I was unable to
achieve this was with QSGMII. Please refer to patch 2 for details.
All mac drivers have now been converted. I would greatly appreciate if
anyone has T-series or P-series boards they can test/debug this series
on. I only have an LS1046ARDB. Everything but QSGMII should work without
breakage; QSGMII needs patches 7 and 8. For this reason, the last 4
patches in this series should be applied together (and should not go
through separate trees).
Changes in v7:
- provide phylink_validate_mask_caps() helper
- Fix oops if memac_pcs_create returned -EPROBE_DEFER
- Fix using pcs-names instead of pcs-handle-names
- Fix not checking for -ENODATA when looking for sgmii pcs
- Fix 81-character line
- Simplify memac_validate with phylink_validate_mask_caps
Changes in v6:
- Remove unnecessary $ref from renesas,rzn1-a5psw
- Remove unnecessary type from pcs-handle-names
- Add maxItems to pcs-handle
- Fix 81-character line
- Fix uninitialized variable in dtsec_mac_config
Changes in v5:
- Add Lynx PCS binding
Changes in v4:
- Use pcs-handle-names instead of pcs-names, as discussed
- Don't fail if phy support was not compiled in
- Split off rate adaptation series
- Split off DPAA "preparation" series
- Split off Lynx 10G support
- t208x: Mark MAC1 and MAC2 as 10G
- Add XFI PCS for t208x MAC1/MAC2
Changes in v3:
- Expand pcs-handle to an array
- Add vendor prefix 'fsl,' to rgmii and mii properties.
- Set maxItems for pcs-names
- Remove phy-* properties from example because dt-schema complains and I
can't be bothered to figure out how to make it work.
- Add pcs-handle as a preferred version of pcsphy-handle
- Deprecate pcsphy-handle
- Remove mii/rmii properties
- Put the PCS mdiodev only after we are done with it (since the PCS
does not perform a get itself).
- Remove _return label from memac_initialization in favor of returning
directly
- Fix grabbing the default PCS not checking for -ENODATA from
of_property_match_string
- Set DTSEC_ECNTRL_R100M in dtsec_link_up instead of dtsec_mac_config
- Remove rmii/mii properties
- Replace 1000Base... with 1000BASE... to match IEEE capitalization
- Add compatibles for QSGMII PCSs
- Split arm and powerpcs dts updates
Changes in v2:
- Better document how we select which PCS to use in the default case
- Move PCS_LYNX dependency to fman Kconfig
- Remove unused variable slow_10g_if
- Restrict valid link modes based on the phy interface. This is easier
to set up, and mostly captures what I intended to do the first time.
We now have a custom validate which restricts half-duplex for some SoCs
for RGMII, but generally just uses the default phylink validate.
- Configure the SerDes in enable/disable
- Properly implement all ethtool ops and ioctls. These were mostly
stubbed out just enough to compile last time.
- Convert 10GEC and dTSEC as well
- Fix capitalization of mEMAC in commit messages
- Add nodes for QSGMII PCSs
- Add nodes for QSGMII PCSs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Anderson [Mon, 17 Oct 2022 20:22:41 +0000 (16:22 -0400)]
arm64: dts: layerscape: Add nodes for QSGMII PCSs
Now that we actually read registers from QSGMII PCSs, it's important
that we have the correct address (instead of hoping that we're the MAC
with all the QSGMII PCSs on its bus). This adds nodes for the QSGMII
PCSs. The exact mapping of QSGMII to MACs depends on the SoC.
Since the first QSGMII PCSs share an address with the SGMII and XFI
PCSs, we only add new nodes for PCSs 2-4. This avoids address conflicts
on the bus.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Anderson [Mon, 17 Oct 2022 20:22:40 +0000 (16:22 -0400)]
powerpc: dts: qoriq: Add nodes for QSGMII PCSs
Now that we actually read registers from QSGMII PCSs, it's important
that we have the correct address (instead of hoping that we're the MAC
with all the QSGMII PCSs on its bus). This adds nodes for the QSGMII
PCSs. They have the same addresses on all SoCs (e.g. if QSGMIIA is
present it's used for MACs 1 through 4).
Since the first QSGMII PCSs share an address with the SGMII and XFI
PCSs, we only add new nodes for PCSs 2-4. This avoids address conflicts
on the bus.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Anderson [Mon, 17 Oct 2022 20:22:39 +0000 (16:22 -0400)]
powerpc: dts: t208x: Mark MAC1 and MAC2 as 10G
On the T208X SoCs, MAC1 and MAC2 support XGMII. Add some new MAC dtsi
fragments, and mark the QMAN ports as 10G.
Fixes:
da414bb923d9 ("powerpc/mpc85xx: Add FSL QorIQ DPAA FMan support to the SoC device tree(s)")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Anderson [Mon, 17 Oct 2022 20:22:38 +0000 (16:22 -0400)]
net: dpaa: Convert to phylink
This converts DPAA to phylink. All macs are converted. This should work
with no device tree modifications (including those made in this series),
except for QSGMII (as noted previously).
The mEMAC configuration is one of the tricker areas. I have tried to
capture all the restrictions across the various models. Most of the time,
we assume that if the serdes supports a mode or the phy-interface-mode
specifies it, then we support it. The only place we can't do this is
(RG)MII, since there's no serdes. In that case, we rely on a (new)
devicetree property. There are also several cases where half-duplex is
broken. Unfortunately, only a single compatible is used for the MAC, so we
have to use the board compatible instead.
The 10GEC conversion is very straightforward, since it only supports XAUI.
There is generally nothing to configure.
The dTSEC conversion is broadly similar to mEMAC, but is simpler because we
don't support configuring the SerDes (though this can be easily added) and
we don't have multiple PCSs. From what I can tell, there's nothing
different in the driver or documentation between SGMII and 1000BASE-X
except for the advertising. Similarly, I couldn't find anything about
2500BASE-X. In both cases, I treat them like SGMII. These modes aren't used
by any in-tree boards. Similarly, despite being mentioned in the driver, I
couldn't find any documented SoCs which supported QSGMII. I have left it
unimplemented for now.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Anderson [Mon, 17 Oct 2022 20:22:37 +0000 (16:22 -0400)]
net: fman: memac: Use lynx pcs driver
Although not stated in the datasheet, as far as I can tell PCS for mEMACs
is a "Lynx." By reusing the existing driver, we can remove the PCS
management code from the memac driver. This requires calling some PCS
functions manually which phylink would usually do for us, but we will let
it do that soon.
One problem is that we don't actually have a PCS for QSGMII. We pretend
that each mEMAC's MDIO bus has four QSGMII PCSs, but this is not the case.
Only the "base" mEMAC's MDIO bus has the four QSGMII PCSs. This is not an
issue yet, because we never get the PCS state. However, it will be once the
conversion to phylink is complete, since the links will appear to never
come up. To get around this, we allow specifying multiple PCSs in pcsphy.
This breaks backwards compatibility with old device trees, but only for
QSGMII. IMO this is the only reasonable way to figure out what the actual
QSGMII PCS is.
Additionally, we now also support a separate XFI PCS. This can allow the
SerDes driver to set different addresses for the SGMII and XFI PCSs so they
can be accessed at the same time.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Anderson [Mon, 17 Oct 2022 20:22:36 +0000 (16:22 -0400)]
net: fman: memac: Add serdes support
This adds support for using a serdes which has to be configured. This is
primarly in preparation for phylink conversion, which will then change the
serdes mode dynamically.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King (Oracle) [Mon, 17 Oct 2022 20:22:35 +0000 (16:22 -0400)]
net: phylink: provide phylink_validate_mask_caps() helper
Provide a helper that restricts the link modes according to the
phylink capabilities.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
[rebased on net-next/master and added documentation]
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Anderson [Mon, 17 Oct 2022 20:22:34 +0000 (16:22 -0400)]
dt-bindings: net: fman: Add additional interface properties
At the moment, mEMACs are configured almost completely based on the
phy-connection-type. That is, if the phy interface is RGMII, it assumed
that RGMII is supported. For some interfaces, it is assumed that the
RCW/bootloader has set up the SerDes properly. This is generally OK, but
restricts runtime reconfiguration. The actual link state is never
reported.
To address these shortcomings, the driver will need additional
information. First, it needs to know how to access the PCS/PMAs (in
order to configure them and get the link status). The SGMII PCS/PMA is
the only currently-described PCS/PMA. Add the XFI and QSGMII PCS/PMAs as
well. The XFI (and 10GBASE-KR) PCS/PMA is a c45 "phy" which sits on the
same MDIO bus as SGMII PCS/PMA. By default they will have conflicting
addresses, but they are also not enabled at the same time by default.
Therefore, we can let the XFI PCS/PMA be the default when
phy-connection-type is xgmii. This will allow for
backwards-compatibility.
QSGMII, however, cannot work with the current binding. This is because
the QSGMII PCS/PMAs are only present on one MAC's MDIO bus. At the
moment this is worked around by having every MAC write to the PCS/PMA
addresses (without checking if they are present). This only works if
each MAC has the same configuration, and only if we don't need to know
the status. Because the QSGMII PCS/PMA will typically be located on a
different MDIO bus than the MAC's SGMII PCS/PMA, there is no fallback
for the QSGMII PCS/PMA.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Anderson [Mon, 17 Oct 2022 20:22:33 +0000 (16:22 -0400)]
dt-bindings: net: Add Lynx PCS binding
This binding is fairly bare-bones for now, since the Lynx driver doesn't
parse any properties (or match based on the compatible). We just need it
in order to prevent the PCS nodes from having phy devices attached to
them. This is not really a problem, but it is a bit inefficient.
This binding is really for three separate PCSs (SGMII, QSGMII, and XFI).
However, the driver treats all of them the same. This works because the
SGMII and XFI devices typically use the same address, and the SerDes
driver (or RCW) muxes between them. The QSGMII PCSs have the same
register layout as the SGMII PCSs. To do things properly, we'd probably
do something like
ethernet-pcs@0 {
#pcs-cells = <1>;
compatible = "fsl,lynx-pcs";
reg = <0>, <1>, <2>, <3>;
};
but that would add complexity, and we can describe the hardware just
fine using separate PCSs for now.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Anderson [Mon, 17 Oct 2022 20:22:32 +0000 (16:22 -0400)]
dt-bindings: net: Expand pcs-handle to an array
This allows multiple phandles to be specified for pcs-handle, such as
when multiple PCSs are present for a single MAC. To differentiate
between them, also add a pcs-handle-names property.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 19 Oct 2022 08:49:38 +0000 (09:49 +0100)]
Merge branch 'net-marvell-yaml'
Michał Grzelak says:
====================
net: further improvements to marvell,pp2.yaml
This patchset addresses problems with reg ranges and
additional $refs. It also limits phy-mode and aligns examples.
Best regards,
Michał
---
Changelog:
v4->v5
- drop '+' from all patternProperties
- restrict range of patternProperties to [0-2] in top level
- drop the $ref in patternProperties:'^...':properties:reg
- add patternProperties:'^...':properties:reg:maximum:2
- drop $ref in patternProperties:'^...':properties:phys
- add patternProperties:'^...':properties:phys:maxItems:1
- limit phy-mode to the subset found in dts files
- reflect the order of subnodes' properties in subnodes' required:
- restrict range of pattern to [0-2] in marvell,armada-7k-pp22 case
- restrict range of pattern to [0-1] in marvell,armada-375-pp2 case
- align to 4 spaces all examples:
- add specified maximum to allOf:if:then-else:properties:reg
v3->v4
- change commit message of first patch
- move allOf:$ref to patternProperties:'^...':$ref
- deprecate port-id in favour of reg
- move reg to front of properties list in patternProperties
- reflect the order of properties in required list in
patternProperties
- add unevaluatedProperties: false to patternProperties
- change unevaluated- to additionalProperties at top level
- add property phys: to ports subnode
- extend example binding with additional information about phys and sfp
- hook phys property to phy-consumer.yaml schema
v2->v3
- move 'reg:description' to 'allOf:if:then'
- change '#size-cells: true' and '#address-cells: true'
to '#size-cells: const: 0' and '#address-cells: const: 1'
- replace all occurences of pattern "^eth\{hex_num}*"
with "^(ethernet-)?port@[0-9]+$"
- add description in 'patternProperties:^...'
- add 'patternProperties:^...:interrupt-names:minItems: 1'
- add 'patternProperties:^...:reg:description'
- update 'patternProperties:^...:port-id:description'
- add 'patternProperties:^...:required: - reg'
- update '*:description:' to uppercase
- add 'allOf:then:required:marvell,system-controller'
- skip quotation marks from 'allOf:$ref'
- add 'else' schema to match 'allOf:if:then'
- restrict 'clocks' in 'allOf:if:then'
- restrict 'clock-names' in 'allOf:if:then'
- add #address-cells=<1>; #size-cells=<0>; in 'examples:'
- change every "ethX" to "ethernet-port@X" in 'examples:'
- add "reg" and comment in all ports in 'examples:'
- change /ethernet/eth0/phy-mode in examples://Armada-375
to "rgmii-id"
- replace each cpm_ with cp0_ in 'examples:'
- replace each _syscon0 with _clk0 in 'examples:'
- remove each eth0X label in 'examples:'
- update armada-375.dtsi and armada-cp11x.dtsi to match
marvell,pp2.yaml
v1->v2
- move 'properties' to the front of the file
- remove blank line after 'properties'
- move 'compatible' to the front of 'properties'
- move 'clocks', 'clock-names' and 'reg' definitions to 'properties'
- substitute all occurences of 'marvell,armada-7k-pp2' with
'marvell,armada-7k-pp22'
- add properties:#size-cells and properties:#address-cells
- specify list in 'interrupt-names'
- remove blank lines after 'patternProperties'
- remove '^interrupt' and '^#.*-cells$' patterns
- remove blank line after 'allOf'
- remove first 'if-then-else' block from 'allOf'
- negate the condition in allOf:if schema
- delete 'interrupt-controller' from section 'examples'
- delete '#interrupt-cells' from section 'examples'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Fri, 14 Oct 2022 21:32:54 +0000 (23:32 +0200)]
ARM: dts: armada-375: Update network description to match schema
Update the PP2 ethernet ports subnodes' names to match
schema enforced by the marvell,pp2.yaml contents.
Add new required properties ('reg') which contains information
about the port ID, keeping 'port-id' ones for backward
compatibility.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Fri, 14 Oct 2022 21:32:53 +0000 (23:32 +0200)]
arm64: dts: marvell: Update network description to match schema
Update the PP2 ethernet ports subnodes' names to match
schema enforced by the marvell,pp2.yaml contents.
Add new required properties ('reg') which contains information
about the port ID, keeping 'port-id' ones for backward
compatibility.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michał Grzelak [Fri, 14 Oct 2022 21:32:52 +0000 (23:32 +0200)]
dt-bindings: net: marvell,pp2: convert to json-schema
Convert the marvell,pp2 bindings from text to proper schema.
Move 'marvell,system-controller' and 'dma-coherent' properties from
port up to the controller node, to match what is actually done in DT.
Rename all subnodes to match "^(ethernet-)?port@[0-2]$" and deprecate
port-id in favour of 'reg'.
Signed-off-by: Michał Grzelak <mig@semihalf.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Mon, 17 Oct 2022 12:12:58 +0000 (14:12 +0200)]
netfilter: nf_tables: relax NFTA_SET_ELEM_KEY_END set flags requirements
Otherwise EINVAL is bogusly reported to userspace when deleting a set
element. NFTA_SET_ELEM_KEY_END does not need to be set in case of:
- insertion: if not present, start key is used as end key.
- deletion: only start key needs to be specified, end key is ignored.
Hence, relax the sanity check.
Fixes:
88cccd908d51 ("netfilter: nf_tables: NFTA_SET_ELEM_KEY_END requires concat and interval flags")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Guillaume Nault [Thu, 13 Oct 2022 14:37:47 +0000 (16:37 +0200)]
netfilter: rpfilter/fib: Set ->flowic_uid correctly for user namespaces.
Currently netfilter's rpfilter and fib modules implicitely initialise
->flowic_uid with 0. This is normally the root UID. However, this isn't
the case in user namespaces, where user ID 0 is mapped to a different
kernel UID. By initialising ->flowic_uid with sock_net_uid(), we get
the root UID of the user namespace, thus keeping the same behaviour
whether or not we're running in a user namepspace.
Note, this is similar to commit
8bcfd0925ef1 ("ipv4: add missing
initialization for flowi4_uid"), which fixed the rp_filter sysctl.
Fixes:
622ec2c9d524 ("net: core: add UID to flows, rules, and routes")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Govindarajulu Varadarajan [Tue, 18 Oct 2022 00:58:04 +0000 (17:58 -0700)]
enic: define constants for legacy interrupts offset
Use macro instead of function calls. These values are constant and will
not change.
Signed-off-by: Govindarajulu Varadarajan <govind.varadar@gmail.com>
Link: https://lore.kernel.org/r/20221018005804.188643-1-govind.varadar@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Shenwei Wang [Mon, 17 Oct 2022 16:12:36 +0000 (11:12 -0500)]
net: fec: remove the unused functions
Removed those unused functions since we simplified the driver
by using the page pool to manage RX buffers.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20221017161236.1563975-1-shenwei.wang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arnd Bergmann [Mon, 17 Oct 2022 12:18:26 +0000 (14:18 +0200)]
net: remove smc911x driver
This driver was used on Arm and SH machines until 2009, when the
last platforms moved to the smsc911x driver for the same hardware.
Time to retire this version.
Link: https://lore.kernel.org/netdev/1232010482-3744-1-git-send-email-steve.glendinning@smsc.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20221017121900.3520108-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Brett Creeley [Mon, 17 Oct 2022 23:31:23 +0000 (16:31 -0700)]
ionic: catch NULL pointer issue on reconfig
It's possible that the driver will dereference a qcq that doesn't exist
when calling ionic_reconfigure_queues(), which causes a page fault BUG.
If a reduction in the number of queues is followed by a different
reconfig such as changing the ring size, the driver can hit a NULL
pointer when trying to clean up non-existent queues.
Fix this by checking to make sure both the qcqs array and qcq entry
exists bofore trying to use and free the entry.
Fixes:
101b40a0171f ("ionic: change queue count with no reset")
Signed-off-by: Brett Creeley <brett@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Link: https://lore.kernel.org/r/20221017233123.15869-1-snelson@pensando.io
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Mon, 17 Oct 2022 16:59:28 +0000 (16:59 +0000)]
net: hsr: avoid possible NULL deref in skb_clone()
syzbot got a crash [1] in skb_clone(), caused by a bug
in hsr_get_untagged_frame().
When/if create_stripped_skb_hsr() returns NULL, we must
not attempt to call skb_clone().
While we are at it, replace a WARN_ONCE() by netdev_warn_once().
[1]
general protection fault, probably for non-canonical address 0xdffffc000000000f: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000078-0x000000000000007f]
CPU: 1 PID: 754 Comm: syz-executor.0 Not tainted 6.0.0-syzkaller-02734-g0326074ff465 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/22/2022
RIP: 0010:skb_clone+0x108/0x3c0 net/core/skbuff.c:1641
Code: 93 02 00 00 49 83 7c 24 28 00 0f 85 e9 00 00 00 e8 5d 4a 29 fa 4c 8d 75 7e 48 b8 00 00 00 00 00 fc ff df 4c 89 f2 48 c1 ea 03 <0f> b6 04 02 4c 89 f2 83 e2 07 38 d0 7f 08 84 c0 0f 85 9e 01 00 00
RSP: 0018:
ffffc90003ccf4e0 EFLAGS:
00010207
RAX:
dffffc0000000000 RBX:
ffffc90003ccf5f8 RCX:
ffffc9000c24b000
RDX:
000000000000000f RSI:
ffffffff8751cb13 RDI:
0000000000000000
RBP:
0000000000000000 R08:
00000000000000f0 R09:
0000000000000140
R10:
fffffbfff181d972 R11:
0000000000000000 R12:
ffff888161fc3640
R13:
0000000000000a20 R14:
000000000000007e R15:
ffffffff8dc5f620
FS:
00007feb621e4700(0000) GS:
ffff8880b9b00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00007feb621e3ff8 CR3:
00000001643a9000 CR4:
00000000003506e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
<TASK>
hsr_get_untagged_frame+0x4e/0x610 net/hsr/hsr_forward.c:164
hsr_forward_do net/hsr/hsr_forward.c:461 [inline]
hsr_forward_skb+0xcca/0x1d50 net/hsr/hsr_forward.c:623
hsr_handle_frame+0x588/0x7c0 net/hsr/hsr_slave.c:69
__netif_receive_skb_core+0x9fe/0x38f0 net/core/dev.c:5379
__netif_receive_skb_one_core+0xae/0x180 net/core/dev.c:5483
__netif_receive_skb+0x1f/0x1c0 net/core/dev.c:5599
netif_receive_skb_internal net/core/dev.c:5685 [inline]
netif_receive_skb+0x12f/0x8d0 net/core/dev.c:5744
tun_rx_batched+0x4ab/0x7a0 drivers/net/tun.c:1544
tun_get_user+0x2686/0x3a00 drivers/net/tun.c:1995
tun_chr_write_iter+0xdb/0x200 drivers/net/tun.c:2025
call_write_iter include/linux/fs.h:2187 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x9e9/0xdd0 fs/read_write.c:584
ksys_write+0x127/0x250 fs/read_write.c:637
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes:
f266a683a480 ("net/hsr: Better frame dispatch")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221017165928.2150130-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vikas Gupta [Mon, 17 Oct 2022 15:32:22 +0000 (11:32 -0400)]
bnxt_en: fix memory leak in bnxt_nvm_test()
Free the kzalloc'ed buffer before returning in the success path.
Fixes:
5b6ff128fdf6 ("bnxt_en: implement callbacks for devlink selftests")
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1666020742-25834-1-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 19 Oct 2022 01:56:41 +0000 (18:56 -0700)]
Merge tag 'for-netdev' of git://git./linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:
====================
pull-request: bpf-next 2022-10-18
We've added 33 non-merge commits during the last 14 day(s) which contain
a total of 31 files changed, 874 insertions(+), 538 deletions(-).
The main changes are:
1) Add RCU grace period chaining to BPF to wait for the completion
of access from both sleepable and non-sleepable BPF programs,
from Hou Tao & Paul E. McKenney.
2) Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values. In the wild we have seen OS vendors doing buggy backports
where helper call numbers mismatched. This is an attempt to make
backports more foolproof, from Andrii Nakryiko.
3) Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions,
from Roberto Sassu.
4) Fix libbpf's BTF dumper for structs with padding-only fields,
from Eduard Zingerman.
5) Fix various libbpf bugs which have been found from fuzzing with
malformed BPF object files, from Shung-Hsi Yu.
6) Clean up an unneeded check on existence of SSE2 in BPF x86-64 JIT,
from Jie Meng.
7) Fix various ASAN bugs in both libbpf and selftests when running
the BPF selftest suite on arm64, from Xu Kuohai.
8) Fix missing bpf_iter_vma_offset__destroy() call in BPF iter selftest
and use in-skeleton link pointer to remove an explicit bpf_link__destroy(),
from Jiri Olsa.
9) Fix BPF CI breakage by pointing to iptables-legacy instead of relying
on symlinked iptables which got upgraded to iptables-nft,
from Martin KaFai Lau.
10) Minor BPF selftest improvements all over the place, from various others.
* tag 'for-netdev' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (33 commits)
bpf/docs: Update README for most recent vmtest.sh
bpf: Use rcu_trace_implies_rcu_gp() for program array freeing
bpf: Use rcu_trace_implies_rcu_gp() in local storage map
bpf: Use rcu_trace_implies_rcu_gp() in bpf memory allocator
rcu-tasks: Provide rcu_trace_implies_rcu_gp()
selftests/bpf: Use sys_pidfd_open() helper when possible
libbpf: Fix null-pointer dereference in find_prog_by_sec_insn()
libbpf: Deal with section with no data gracefully
libbpf: Use elf_getshdrnum() instead of e_shnum
selftest/bpf: Fix error usage of ASSERT_OK in xdp_adjust_tail.c
selftests/bpf: Fix error failure of case test_xdp_adjust_tail_grow
selftest/bpf: Fix memory leak in kprobe_multi_test
selftests/bpf: Fix memory leak caused by not destroying skeleton
libbpf: Fix memory leak in parse_usdt_arg()
libbpf: Fix use-after-free in btf_dump_name_dups
selftests/bpf: S/iptables/iptables-legacy/ in the bpf_nf and xdp_synproxy test
selftests/bpf: Alphabetize DENYLISTs
selftests/bpf: Add tests for _opts variants of bpf_*_get_fd_by_id()
libbpf: Introduce bpf_link_get_fd_by_id_opts()
libbpf: Introduce bpf_btf_get_fd_by_id_opts()
...
====================
Link: https://lore.kernel.org/r/20221018210631.11211-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikos Tsironis [Thu, 29 Sep 2022 14:11:48 +0000 (17:11 +0300)]
dm clone: Fix typo in block_device format specifier
Use %pg for printing the block device name, instead of %pd.
Fixes:
385411ffba0c ("dm: stop using bdevname")
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Genjian Zhang [Thu, 29 Sep 2022 08:20:36 +0000 (16:20 +0800)]
dm: remove unnecessary assignment statement in alloc_dev()
Fixes:
74fe6ba923949 ("dm: convert to blk_alloc_disk/blk_cleanup_disk")
Signed-off-by: Genjian Zhang <zhanggenjian@kylinos.cn>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Milan Broz [Tue, 27 Sep 2022 18:42:26 +0000 (20:42 +0200)]
dm verity: Add documentation for try_verify_in_tasklet option
Add documentation that was missing from commit
5721d4e5a9cd ("dm
verity: Add optional "try_verify_in_tasklet" feature").
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Shaomin Deng [Sun, 4 Sep 2022 16:04:27 +0000 (12:04 -0400)]
dm cache: delete the redundant word 'each' in comment
Signed-off-by: Shaomin Deng <dengshaomin@cdjrlc.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Jiangshan Yi [Mon, 5 Sep 2022 02:45:52 +0000 (10:45 +0800)]
dm raid: fix typo in analyse_superblocks code comment
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: Jiangshan Yi <yijiangshan@kylinos.cn>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Nathan Huckleberry [Tue, 30 Aug 2022 18:44:44 +0000 (18:44 +0000)]
dm verity: enable WQ_HIGHPRI on verify_wq
WQ_HIGHPRI increases throughput and decreases disk latency when using
dm-verity. This is important in Android for camera startup speed.
The following tests were run by doing 60 seconds of random reads using
a dm-verity device backed by two ramdisks.
Without WQ_HIGHPRI
lat (usec): min=13, max=3947, avg=69.53, stdev=50.55
READ: bw=51.1MiB/s (53.6MB/s), 51.1MiB/s-51.1MiB/s (53.6MB/s-53.6MB/s)
With WQ_HIGHPRI:
lat (usec): min=13, max=7854, avg=31.15, stdev=30.42
READ: bw=116MiB/s (121MB/s), 116MiB/s-116MiB/s (121MB/s-121MB/s)
Further testing was done by measuring how long it takes to open a
camera on an Android device.
Without WQ_HIGHPRI
Total verity work queue wait times (ms):
880.960, 789.517, 898.852
With WQ_HIGHPRI:
Total verity work queue wait times (ms):
528.824, 439.191, 433.300
The average time to open the camera is reduced by 350ms (or 40-50%).
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Jilin Yuan [Tue, 30 Aug 2022 15:33:45 +0000 (23:33 +0800)]
dm raid: delete the redundant word 'that' in comment
Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Mikulas Patocka [Wed, 24 Aug 2022 11:25:57 +0000 (07:25 -0400)]
dm: change from DMWARN to DMERR or DMCRIT for fatal errors
Change DMWARN to DMERR in cases when there is an unrecoverable error.
Change DMWARN to DMCRIT when handling of a case is unimplemented.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Daniel Müller [Mon, 17 Oct 2022 23:24:58 +0000 (23:24 +0000)]
bpf/docs: Update README for most recent vmtest.sh
Since commit
40b09653b197 ("selftests/bpf: Adjust vmtest.sh to use local
kernel configuration") the vmtest.sh script no longer downloads a kernel
configuration but uses the local, in-repository one.
This change updates the README, which still mentions the old behavior.
Signed-off-by: Daniel Müller <deso@posteo.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20221017232458.1272762-1-deso@posteo.net
Linus Torvalds [Tue, 18 Oct 2022 18:25:50 +0000 (11:25 -0700)]
Merge tag 'for-6.1-rc1-tag' of git://git./linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- fiemap fixes:
- add missing path cache update
- fix processing of delayed data and tree refs during backref
walking, this could lead to reporting incorrect extent sharing
- fix extent range locking under heavy contention to avoid deadlocks
- make it possible to test send v3 in debugging mode
- update links in MAINTAINERS
* tag 'for-6.1-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
MAINTAINERS: update btrfs website links and files
btrfs: ignore fiemap path cache if we have multiple leaves for a data extent
btrfs: fix processing of delayed tree block refs during backref walking
btrfs: fix processing of delayed data refs during backref walking
btrfs: delete stale comments after merge conflict resolution
btrfs: unlock locked extent area if we have contention
btrfs: send: update command for protocol version check
btrfs: send: allow protocol version 3 with CONFIG_BTRFS_DEBUG
btrfs: add missing path cache update during fiemap
Linus Torvalds [Tue, 18 Oct 2022 18:18:26 +0000 (11:18 -0700)]
Merge tag 'erofs-for-6.1-rc2-fixes' of git://git./linux/kernel/git/xiang/erofs
Pull erofs fixes from Gao Xiang:
- Fix invalid unmapped accesses when initializing compressed inodes
- Fix up very rare hung on page lock after enabling compressed data
deduplication
- Fix up inplace decompression success rate
- Take s_inode_list_lock to protect sb->s_inodes for fscache shared
domain
* tag 'erofs-for-6.1-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: protect s_inodes with s_inode_list_lock for fscache
erofs: fix up inplace decompression success rate
erofs: shouldn't churn the mapping page for duplicated copies
erofs: fix illegal unmapped accesses in z_erofs_fill_inode_lazy()
Alexei Starovoitov [Tue, 18 Oct 2022 17:27:02 +0000 (10:27 -0700)]
Merge branch 'Remove unnecessary RCU grace period chaining'
Hou Tao says:
====================
Now bpf uses RCU grace period chaining to wait for the completion of
access from both sleepable and non-sleepable bpf program: calling
call_rcu_tasks_trace() firstly to wait for a RCU-tasks-trace grace
period, then in its callback calls call_rcu() or kfree_rcu() to wait for
a normal RCU grace period.
According to the implementation of RCU Tasks Trace, it inovkes
->postscan_func() to wait for one RCU-tasks-trace grace period and
rcu_tasks_trace_postscan() inovkes synchronize_rcu() to wait for one
normal RCU grace period in turn, so one RCU-tasks-trace grace period
will imply one normal RCU grace period. To codify the implication,
introduces rcu_trace_implies_rcu_gp() in patch #1. And using it in patch
Other two uses of call_rcu_tasks_trace() are unchanged: for
__bpf_prog_put_rcu() there is no gp chain and for
__bpf_tramp_image_put_rcu_tasks() it chains RCU tasks trace GP and RCU
tasks GP.
An alternative way to remove these unnecessary RCU grace period
chainings is using the RCU polling API to check whether or not a normal
RCU grace period has passed (e.g. get_state_synchronize_rcu()). But it
needs an unsigned long space for each free element or each call, and
it is not affordable for local storage element, so as for now always
rcu_trace_implies_rcu_gp().
Comments are always welcome.
Change Log:
v2:
* codify the implication of RCU Tasks Trace grace period instead of
assuming for it
v1: https://lore.kernel.org/bpf/
20221011071128.3470622-1-houtao@huaweicloud.com
Hou Tao (3):
bpf: Use rcu_trace_implies_rcu_gp() in bpf memory allocator
bpf: Use rcu_trace_implies_rcu_gp() in local storage map
bpf: Use rcu_trace_implies_rcu_gp() for program array freeing
====================
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Hou Tao [Fri, 14 Oct 2022 11:39:46 +0000 (19:39 +0800)]
bpf: Use rcu_trace_implies_rcu_gp() for program array freeing
To support both sleepable and normal uprobe bpf program, the freeing of
trace program array chains a RCU-tasks-trace grace period and a normal
RCU grace period one after the other.
With the introduction of rcu_trace_implies_rcu_gp(),
__bpf_prog_array_free_sleepable_cb() can check whether or not a normal
RCU grace period has also passed after a RCU-tasks-trace grace period
has passed. If it is true, it is safe to invoke kfree() directly.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20221014113946.965131-5-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Hou Tao [Fri, 14 Oct 2022 11:39:45 +0000 (19:39 +0800)]
bpf: Use rcu_trace_implies_rcu_gp() in local storage map
Local storage map is accessible for both sleepable and non-sleepable bpf
program, and its memory is freed by using both call_rcu_tasks_trace() and
kfree_rcu() to wait for both RCU-tasks-trace grace period and RCU grace
period to pass.
With the introduction of rcu_trace_implies_rcu_gp(), both
bpf_selem_free_rcu() and bpf_local_storage_free_rcu() can check whether
or not a normal RCU grace period has also passed after a RCU-tasks-trace
grace period has passed. If it is true, it is safe to call kfree()
directly.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20221014113946.965131-4-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Hou Tao [Fri, 14 Oct 2022 11:39:44 +0000 (19:39 +0800)]
bpf: Use rcu_trace_implies_rcu_gp() in bpf memory allocator
The memory free logic in bpf memory allocator chains a RCU Tasks Trace
grace period and a normal RCU grace period one after the other, so it
can ensure that both sleepable and non-sleepable programs have finished.
With the introduction of rcu_trace_implies_rcu_gp(),
__free_rcu_tasks_trace() can check whether or not a normal RCU grace
period has also passed after a RCU Tasks Trace grace period has passed.
If it is true, freeing these elements directly, else freeing through
call_rcu().
Signed-off-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20221014113946.965131-3-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Paul E. McKenney [Fri, 14 Oct 2022 11:39:43 +0000 (19:39 +0800)]
rcu-tasks: Provide rcu_trace_implies_rcu_gp()
As an accident of implementation, an RCU Tasks Trace grace period also
acts as an RCU grace period. However, this could change at any time.
This commit therefore creates an rcu_trace_implies_rcu_gp() that currently
returns true to codify this accident. Code relying on this accident
must call this function to verify that this accident is still happening.
Reported-by: Hou Tao <houtao@huaweicloud.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Martin KaFai Lau <martin.lau@linux.dev>
Link: https://lore.kernel.org/r/20221014113946.965131-2-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Mikulas Patocka [Tue, 18 Oct 2022 14:06:45 +0000 (10:06 -0400)]
dm bufio: use the acquire memory barrier when testing for B_READING
The function test_bit doesn't provide any memory barrier. It may be
possible that the read requests that follow test_bit(B_READING, &b->state)
are reordered before the test, reading invalid data that existed before
B_READING was cleared.
Fix this bug by changing test_bit to test_bit_acquire. This is
particularly important on arches with weak(er) memory ordering
(e.g. arm64).
Depends-On:
8238b4579866 ("wait_on_bit: add an acquire memory barrier")
Depends-On:
d6ffe6067a54 ("provide arch_test_bit_acquire for architectures that define test_bit")
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Jiapeng Chong [Mon, 17 Oct 2022 09:35:40 +0000 (17:35 +0800)]
net: ip6_gre: Remove the unused function ip6gre_tnl_addr_conflict()
The function ip6gre_tnl_addr_conflict() is defined in the ip6_gre.c file,
but not called elsewhere, so delete this unused function.
net/ipv6/ip6_gre.c:887:20: warning: unused function 'ip6gre_tnl_addr_conflict'.
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2419
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/20221017093540.26806-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Zhengchao Shao [Mon, 17 Oct 2022 08:03:31 +0000 (16:03 +0800)]
ip6mr: fix UAF issue in ip6mr_sk_done() when addrconf_init_net() failed
If the initialization fails in calling addrconf_init_net(), devconf_all is
the pointer that has been released. Then ip6mr_sk_done() is called to
release the net, accessing devconf->mc_forwarding directly causes invalid
pointer access.
The process is as follows:
setup_net()
ops_init()
addrconf_init_net()
all = kmemdup(...) ---> alloc "all"
...
net->ipv6.devconf_all = all;
__addrconf_sysctl_register() ---> failed
...
kfree(all); ---> ipv6.devconf_all invalid
...
ops_exit_list()
...
ip6mr_sk_done()
devconf = net->ipv6.devconf_all;
//devconf is invalid pointer
if (!devconf || !atomic_read(&devconf->mc_forwarding))
The following is the Call Trace information:
BUG: KASAN: use-after-free in ip6mr_sk_done+0x112/0x3a0
Read of size 4 at addr
ffff888075508e88 by task ip/14554
Call Trace:
<TASK>
dump_stack_lvl+0x8e/0xd1
print_report+0x155/0x454
kasan_report+0xba/0x1f0
kasan_check_range+0x35/0x1b0
ip6mr_sk_done+0x112/0x3a0
rawv6_close+0x48/0x70
inet_release+0x109/0x230
inet6_release+0x4c/0x70
sock_release+0x87/0x1b0
igmp6_net_exit+0x6b/0x170
ops_exit_list+0xb0/0x170
setup_net+0x7ac/0xbd0
copy_net_ns+0x2e6/0x6b0
create_new_namespaces+0x382/0xa50
unshare_nsproxy_namespaces+0xa6/0x1c0
ksys_unshare+0x3a4/0x7e0
__x64_sys_unshare+0x2d/0x40
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x7f7963322547
</TASK>
Allocated by task 14554:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
__kasan_kmalloc+0xa1/0xb0
__kmalloc_node_track_caller+0x4a/0xb0
kmemdup+0x28/0x60
addrconf_init_net+0x1be/0x840
ops_init+0xa5/0x410
setup_net+0x5aa/0xbd0
copy_net_ns+0x2e6/0x6b0
create_new_namespaces+0x382/0xa50
unshare_nsproxy_namespaces+0xa6/0x1c0
ksys_unshare+0x3a4/0x7e0
__x64_sys_unshare+0x2d/0x40
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Freed by task 14554:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
kasan_save_free_info+0x2a/0x40
____kasan_slab_free+0x155/0x1b0
slab_free_freelist_hook+0x11b/0x220
__kmem_cache_free+0xa4/0x360
addrconf_init_net+0x623/0x840
ops_init+0xa5/0x410
setup_net+0x5aa/0xbd0
copy_net_ns+0x2e6/0x6b0
create_new_namespaces+0x382/0xa50
unshare_nsproxy_namespaces+0xa6/0x1c0
ksys_unshare+0x3a4/0x7e0
__x64_sys_unshare+0x2d/0x40
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes:
7d9b1b578d67 ("ip6mr: fix use-after-free in ip6mr_sk_done()")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221017080331.16878-1-shaozhengchao@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Kuniyuki Iwashima [Fri, 14 Oct 2022 18:26:25 +0000 (11:26 -0700)]
udp: Update reuse->has_conns under reuseport_lock.
When we call connect() for a UDP socket in a reuseport group, we have
to update sk->sk_reuseport_cb->has_conns to 1. Otherwise, the kernel
could select a unconnected socket wrongly for packets sent to the
connected socket.
However, the current way to set has_conns is illegal and possible to
trigger that problem. reuseport_has_conns() changes has_conns under
rcu_read_lock(), which upgrades the RCU reader to the updater. Then,
it must do the update under the updater's lock, reuseport_lock, but
it doesn't for now.
For this reason, there is a race below where we fail to set has_conns
resulting in the wrong socket selection. To avoid the race, let's split
the reader and updater with proper locking.
cpu1 cpu2
+----+ +----+
__ip[46]_datagram_connect() reuseport_grow()
. .
|- reuseport_has_conns(sk, true) |- more_reuse = __reuseport_alloc(more_socks_size)
| . |
| |- rcu_read_lock()
| |- reuse = rcu_dereference(sk->sk_reuseport_cb)
| |
| | | /* reuse->has_conns == 0 here */
| | |- more_reuse->has_conns = reuse->has_conns
| |- reuse->has_conns = 1 | /* more_reuse->has_conns SHOULD BE 1 HERE */
| | |
| | |- rcu_assign_pointer(reuse->socks[i]->sk_reuseport_cb,
| | | more_reuse)
| `- rcu_read_unlock() `- kfree_rcu(reuse, rcu)
|
|- sk->sk_state = TCP_ESTABLISHED
Note the likely(reuse) in reuseport_has_conns_set() is always true,
but we put the test there for ease of review. [0]
For the record, usually, sk_reuseport_cb is changed under lock_sock().
The only exception is reuseport_grow() & TCP reqsk migration case.
1) shutdown() TCP listener, which is moved into the latter part of
reuse->socks[] to migrate reqsk.
2) New listen() overflows reuse->socks[] and call reuseport_grow().
3) reuse->max_socks overflows u16 with the new listener.
4) reuseport_grow() pops the old shutdown()ed listener from the array
and update its sk->sk_reuseport_cb as NULL without lock_sock().
shutdown()ed TCP sk->sk_reuseport_cb can be changed without lock_sock(),
but, reuseport_has_conns_set() is called only for UDP under lock_sock(),
so likely(reuse) never be false in reuseport_has_conns_set().
[0]: https://lore.kernel.org/netdev/CANn89iLja=eQHbsM_Ta2sQF0tOGU8vAGrh_izRuuHjuO1ouUag@mail.gmail.com/
Fixes:
acdcecc61285 ("udp: correct reuseport selection with connected sockets")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20221014182625.89913-1-kuniyu@amazon.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Linus Torvalds [Tue, 18 Oct 2022 01:52:43 +0000 (18:52 -0700)]
Merge tag 'cgroup-for-6.1-rc1-fixes' of git://git./linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
- Fix a recent regression where a sleeping kernfs function is called
with css_set_lock (spinlock) held
- Revert the commit to enable cgroup1 support for cgroup_get_from_fd/file()
Multiple users assume that the lookup only works for cgroup2 and
breaks when fed a cgroup1 file. Instead, introduce a separate set of
functions to lookup both v1 and v2 and use them where the user
explicitly wants to support both versions.
- Compat update for tools/perf/util/bpf_skel/bperf_cgroup.bpf.c.
- Add Josef Bacik as a blkcg maintainer.
* tag 'cgroup-for-6.1-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
blkcg: Update MAINTAINERS entry
mm: cgroup: fix comments for get from fd/file helpers
perf stat: Support old kernels for bperf cgroup counting
bpf: cgroup_iter: support cgroup1 using cgroup fd
cgroup: add cgroup_v1v2_get_from_[fd/file]()
Revert "cgroup: enable cgroup_get_from_file() on cgroup1"
cgroup: Reorganize css_set_lock and kernfs path processing
Damien Le Moal [Fri, 14 Oct 2022 02:03:49 +0000 (11:03 +0900)]
ata: ahci_qoriq: Fix compilation warning
When compiling with clang and W=1, the following warning is generated:
drivers/ata/ahci_qoriq.c:283:22: error: cast to smaller integer type
'enum ahci_qoriq_type' from 'const void *'
[-Werror,-Wvoid-pointer-to-enum-cast]
qoriq_priv->type = (enum ahci_qoriq_type)of_id->data;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix this by using a cast to unsigned long to match the "void *" type
size of of_id->data.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Damien Le Moal [Fri, 14 Oct 2022 01:48:16 +0000 (10:48 +0900)]
ata: ahci_imx: Fix compilation warning
When compiling with clang and W=1, the following warning is generated:
drivers/ata/ahci_imx.c:1070:18: error: cast to smaller integer type
'enum ahci_imx_type' from 'const void *'
[-Werror,-Wvoid-pointer-to-enum-cast]
imxpriv->type = (enum ahci_imx_type)of_id->data;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix this by using a cast to unsigned long to match the "void *" type
size of of_id->data.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Damien Le Moal [Fri, 14 Oct 2022 01:45:58 +0000 (10:45 +0900)]
ata: ahci_xgene: Fix compilation warning
When compiling with clang and W=1, the following warning is generated:
drivers/ata/ahci_xgene.c:788:14: error: cast to smaller integer type
'enum xgene_ahci_version' from 'const void *'
[-Werror,-Wvoid-pointer-to-enum-cast]
version = (enum xgene_ahci_version) of_devid->data;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix this by using a cast to unsigned long to match the "void *" type
size of of_devid->data.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Damien Le Moal [Fri, 14 Oct 2022 01:42:57 +0000 (10:42 +0900)]
ata: ahci_brcm: Fix compilation warning
When compiling with clang and W=1, the following warning is generated:
drivers/ata/ahci_brcm.c:451:18: error: cast to smaller integer type
'enum brcm_ahci_version' from 'const void *'
[-Werror,-Wvoid-pointer-to-enum-cast]
priv->version = (enum brcm_ahci_version)of_id->data;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix this by using a cast to unsigned long to match the "void *" type
size of of_id->data.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Damien Le Moal [Fri, 14 Oct 2022 01:38:15 +0000 (10:38 +0900)]
ata: sata_rcar: Fix compilation warning
When compiling with clang and W=1, the following warning is generated:
drivers/ata/sata_rcar.c:878:15: error: cast to smaller integer type
'enum sata_rcar_type' from 'const void *'
[-Werror,-Wvoid-pointer-to-enum-cast]
priv->type = (enum sata_rcar_type)of_device_get_match_data(dev);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix this by using a cast to unsigned long to match the "void *" type
size returned by of_device_get_match_data().
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Tejun Heo [Mon, 17 Oct 2022 18:08:05 +0000 (08:08 -1000)]
blkcg: Update MAINTAINERS entry
Josef wrote iolatency and iocost is missing from the files list. Let's add
Josef as a maintainer and add blk-iocost.c to the files list.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jens Axboe <axboe@kernel.dk>
Linus Torvalds [Mon, 17 Oct 2022 17:20:04 +0000 (10:20 -0700)]
Merge tag 'v6.1-p2' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes an issue exposed by the recent change to feed untrusted
sources into /dev/random"
* tag 'v6.1-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: bcm2835 - use hwrng_msleep() instead of cpu_relax()
projects / platform / kernel / linux-starfive.git / log