spi: npcm-pspi: fix 16 bit send and receive support

Fixing NPCM BMC Peripheral SPI controller 16 bit
send and receive support by writing and reading
the SPI data in the right order.

Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/r/20200115162301.235926-2-tmaimon77@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Add support for Intel Comet Lake PCH-V

Add support for Intel Comet Lake PCH-V which has the same LPSS than on
Intel Kaby lake unlike other Intel Comet Lake PCH variants that are based
on Intel Cannon Lake PCH LPSS.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20200116091035.575175-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: dw: use "smp_mb()" to avoid sending spi data error

Because of out-of-order execution about some CPU architecture,
In this debug stage we find Completing spi interrupt enable ->
prodrucing TXEI interrupt -> running "interrupt_transfer" function
will prior to set "dw->rx and dws->rx_end" data, so this patch add
memory barrier to enable dw->rx and dw->rx_end to be visible and
solve to send SPI data error.
eg:
it will fix to this following low possibility error in testing environment
which using SPI control to connect TPM Modules

kernel: tpm tpm0: Operation Timed out
kernel: tpm tpm0: tpm_relinquish_locality: : error -1

Signed-off-by: fengsheng <fengsheng5@huawei.com>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Link: https://lore.kernel.org/r/1578019930-55858-1-git-send-email-kong.kongxinwei@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: Document Octal mode as valid SPI bus width

SPI core supports Octal SPI controllers which have 8 IO lines.
Therefore document 8 as a valid option for spi-tx{rx}-bus-width

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200102102118.23318-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: spi-dw: Add lock protect dw_spi rx/tx to prevent concurrent calls

dw_spi_irq() and dw_spi_transfer_one concurrent calls.

I find a panic in dw_writer(): txw = *(u8 *)(dws->tx), when dw->tx==null,
dw->len==4, and dw->tx_end==1.

When tpm driver's message overtime dw_spi_irq() and dw_spi_transfer_one
may concurrent visit dw_spi, so I think dw_spi structure lack of protection.

Otherwise dw_spi_transfer_one set dw rx/tx buffer and then open irq,
store dw rx/tx instructions and other cores handle irq load dw rx/tx
instructions may out of order.

[ 1025.321302] Call trace:
...
[ 1025.321319]  __crash_kexec+0x98/0x148
[ 1025.321323]  panic+0x17c/0x314
[ 1025.321329]  die+0x29c/0x2e8
[ 1025.321334]  die_kernel_fault+0x68/0x78
[ 1025.321337]  __do_kernel_fault+0x90/0xb0
[ 1025.321346]  do_page_fault+0x88/0x500
[ 1025.321347]  do_translation_fault+0xa8/0xb8
[ 1025.321349]  do_mem_abort+0x68/0x118
[ 1025.321351]  el1_da+0x20/0x8c
[ 1025.321362]  dw_writer+0xc8/0xd0
[ 1025.321364]  interrupt_transfer+0x60/0x110
[ 1025.321365]  dw_spi_irq+0x48/0x70
...

Signed-off-by: wuxu.wu <wuxu.wu@huawei.com>
Link: https://lore.kernel.org/r/1577849981-31489-1-git-send-email-wuxu.wu@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: spi-fsl-dspi: Fix 16-bit word order in 32-bit XSPI mode

When used in Extended SPI mode on LS1021A, the DSPI controller wants to
have the least significant 16-bit word written first to the TX FIFO.

In fact, the LS1021A reference manual says:

33.5.2.4.2 Draining the TX FIFO

When Extended SPI Mode (DSPIx_MCR[XSPI]) is enabled, if the frame size
of SPI Data to be transmitted is more than 16 bits, then it causes two
Data entries to be popped from TX FIFO simultaneously which are
transferred to the shift register. The first of the two popped entries
forms the 16 least significant bits of the SPI frame to be transmitted.

So given the following TX buffer:

 +-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
 | 0x0 | 0x1 | 0x2 | 0x3 | 0x4 | 0x5 | 0x6 | 0x7 | 0x8 | 0x9 | 0xa | 0xb |
 +-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
 |     32-bit word 1     |     32-bit word 2     |     32-bit word 3     |
 +-----------------------+-----------------------+-----------------------+

The correct way that a little-endian system should transmit it on the
wire when bits_per_word is 32 is:

0x03020100
0x07060504
0x0b0a0908

But it is actually transmitted as following, as seen with a scope:

0x01000302
0x05040706
0x09080b0a

It appears that this patch has been submitted at least once before:
https://lkml.org/lkml/2018/9/21/286
but in that case Chuanhua Han did not manage to explain the problem
clearly enough and the patch did not get merged, leaving XSPI mode
broken.

Fixes: 8fcd151d2619 ("spi: spi-fsl-dspi: XSPI FIFO handling (in TCFQ mode)")
Cc: Esben Haabendal <eha@deif.com>
Cc: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20191228135536.14284-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

spi: Don't look at TX buffer for PTP system timestamping

The API for PTP system timestamping (associating a SPI transaction with
the system time at which it was transferred) is flawed: it assumes that
the xfer->tx_buf pointer will always be present.

This is, of course, not always the case.

So introduce a "progress" variable that denotes how many word have been
transferred.

Fix the Freescale DSPI driver, the only user of the API so far, in the
same patch.

Fixes: b42faeee718c ("spi: Add a PTP system timestamp to the transfer structure")
Fixes: d6b71dfaeeba ("spi: spi-fsl-dspi: Implement the PTP system timestamping for TCFQ mode")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20191227012417.1057-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: uniphier: Fix FIFO threshold

Rx threshold means the value to inform the receiver when the number of words
in Rx FIFO is equal to or more than the value. Similarly, Tx threshold means
the value to inform the sender when the number of words in Tx FIFO is equal
to or less than the value. The controller triggers the driver to start
the transfer.

In case of Rx, the driver wants to detect that the specified number of words
N are in Rx FIFO, so the value of Rx threshold should be N. In case of Tx,
the driver wants to detect that the same number of spaces as Rx are in
Tx FIFO, so the value of Tx threshold should be (FIFO size - N).

For example, in order for the driver to receive at least 3 words from
Rx FIFO, set 3 to Rx threshold.
   +-+-+-+-+-+-+-+-+
   | | | | | |*|*|*|
   +-+-+-+-+-+-+-+-+

In order for the driver to send at least 3 words to Tx FIFO, because
it needs at least 3 spaces, set 8(FIFO size) - 3 = 5 to Tx threshold.
   +-+-+-+-+-+-+-+-+
   |*|*|*|*|*| | | |
   +-+-+-+-+-+-+-+-+

This adds new function uniphier_spi_set_fifo_threshold() to set
threshold value to the register.

And more, FIFO counts by 'words', so this renames 'fill_bytes' with
'fill_words', and fixes the calculation using bytes_per_words.

Fixes: 37ffab817098 ("spi: uniphier: introduce polling mode")
Cc: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1577149107-30670-2-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: fsl: use platform_get_irq() instead of of_irq_to_resource()

Unlike irq_of_parse_and_map() which has a dummy definition on SPARC,
of_irq_to_resource() hasn't.

But as platform_get_irq() can be used instead and is generic, use it.

Reported-by: kbuild test robot <lkp@intel.com>
Suggested-by: Mark Brown <broonie@kernel.org>
Fixes:  3194d2533eff ("spi: fsl: don't map irq during probe")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/091a277fd0b3356dca1e29858c1c96983fc9cb25.1576172743.git.christophe.leroy@c-s.fr
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: nxp-fspi: Ensure width is respected in spi-mem operations

Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.

Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.

Fixes: a5356aef6a90 ("spi: spi-mem: Add driver for NXP FlexSPI controller")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20191211195730.26794-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: spi-ti-qspi: Fix a bug when accessing non default CS

When switching ChipSelect from default CS0 to any other CS, driver fails
to update the bits in system control module register that control which
CS is mapped for MMIO access. This causes reads to fail when driver
tries to access QSPI flash on CS1/2/3.

Fix this by updating appropriate bits whenever active CS changes.

Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20191211155216.30212-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: fsl: don't map irq during probe

With lastest kernel, the following warning is observed at startup:

[    1.500609] ------------[ cut here ]------------
[    1.505225] remove_proc_entry: removing non-empty directory 'irq/22', leaking at least 'fsl_spi'
[    1.514234] WARNING: CPU: 0 PID: 1 at fs/proc/generic.c:682 remove_proc_entry+0x198/0x1c0
[    1.522403] CPU: 0 PID: 1 Comm: swapper Not tainted 5.4.0-s3k-dev-02248-g93532430a4ff #2564
[    1.530724] NIP:  c0197694 LR: c0197694 CTR: c0050d80
[    1.535762] REGS: df4a5af0 TRAP: 0700   Not tainted  (5.4.0-02248-g93532430a4ff)
[    1.543818] MSR:  00029032 <EE,ME,IR,DR,RI>  CR: 22028222  XER: 00000000
[    1.550524]
[    1.550524] GPR00: c0197694 df4a5ba8 df4a0000 00000054 00000000 00000000 00004a38 00000010
[    1.550524] GPR08: c07c5a30 00000800 00000000 00001032 22000208 00000000 c0004b14 00000000
[    1.550524] GPR16: 00000000 00000000 00000000 00000000 00000000 00000000 c0830000 c07fc078
[    1.550524] GPR24: c08e8ca0 df665d10 df60ea98 c07c9db8 00000001 df5d5ae3 df5d5a80 df43f8e3
[    1.585327] NIP [c0197694] remove_proc_entry+0x198/0x1c0
[    1.590628] LR [c0197694] remove_proc_entry+0x198/0x1c0
[    1.595829] Call Trace:
[    1.598280] [df4a5ba8] [c0197694] remove_proc_entry+0x198/0x1c0 (unreliable)
[    1.605321] [df4a5bd8] [c0067acc] unregister_irq_proc+0x5c/0x70
[    1.611238] [df4a5bf8] [c005fbc4] free_desc+0x3c/0x80
[    1.616286] [df4a5c18] [c005fe2c] irq_free_descs+0x70/0xa8
[    1.621778] [df4a5c38] [c033d3fc] of_fsl_spi_probe+0xdc/0x3cc
[    1.627525] [df4a5c88] [c02f0f64] platform_drv_probe+0x44/0xa4
[    1.633350] [df4a5c98] [c02eee44] really_probe+0x1ac/0x418
[    1.638829] [df4a5cc8] [c02ed3e8] bus_for_each_drv+0x64/0xb0
[    1.644481] [df4a5cf8] [c02ef950] __device_attach+0xd4/0x128
[    1.650132] [df4a5d28] [c02ed61c] bus_probe_device+0xa0/0xbc
[    1.655783] [df4a5d48] [c02ebbe8] device_add+0x544/0x74c
[    1.661096] [df4a5d88] [c0382b78] of_platform_device_create_pdata+0xa4/0x100
[    1.668131] [df4a5da8] [c0382cf4] of_platform_bus_create+0x120/0x20c
[    1.674474] [df4a5df8] [c0382d50] of_platform_bus_create+0x17c/0x20c
[    1.680818] [df4a5e48] [c0382e88] of_platform_bus_probe+0x9c/0xf0
[    1.686907] [df4a5e68] [c0751404] __machine_initcall_cmpcpro_cmpcpro_declare_of_platform_devices+0x74/0x1a4
[    1.696629] [df4a5e98] [c072a4cc] do_one_initcall+0x8c/0x1d4
[    1.702282] [df4a5ef8] [c072a768] kernel_init_freeable+0x154/0x204
[    1.708455] [df4a5f28] [c0004b2c] kernel_init+0x18/0x110
[    1.713769] [df4a5f38] [c00122ac] ret_from_kernel_thread+0x14/0x1c
[    1.719926] Instruction dump:
[    1.722889] 2c030000 4182004c 3863ffb0 3c80c05f 80e3005c 388436a0 3c60c06d 7fa6eb78
[    1.730630] 7fe5fb78 38840280 38634178 4be8c611 <0fe00000> 4bffff6c 3c60c071 7fe4fb78
[    1.738556] ---[ end trace 05d0720bf2e352e2 ]---

The problem comes from the error path which calls
irq_dispose_mapping() while the IRQ has been requested with
devm_request_irq().

IRQ doesn't need to be mapped with irq_of_parse_and_map(). The only
need is to get the IRQ virtual number. For that, use
of_irq_to_resource() instead of the
irq_of_parse_and_map()/irq_dispose_mapping() pair.

Fixes: 500a32abaf81 ("spi: fsl: Call irq_dispose_mapping in err path")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/518cfb83347d5372748e7fe72f94e2e9443d0d4a.1575905123.git.christophe.leroy@c-s.fr
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: spi-cavium-thunderx: Add missing pci_release_regions()

The driver forgets to call pci_release_regions() in probe failure
and remove.
Add the missed calls to fix it.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191206075500.18525-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: sprd: Fix the incorrect SPI register

The original code used an incorrect SPI register to initialize the SPI
controller in sprd_spi_init_hw(), thus fix it.

Fixes: e7d973a31c24 ("spi: sprd: Add SPI driver for Spreadtrum SC9860")
Signed-off-by: Huanpeng Xin <huanpeng.xin@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/b4f7f89ec0fdc595335687bfbd9f962213bc4a1d.1575443510.git.baolin.wang7@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

gpiolib: of: Make of_gpio_spi_cs_get_count static

Fix sparse warning:

drivers/gpio/gpiolib-of.c:35:5: warning:
 symbol 'of_gpio_spi_cs_get_count' was not declared. Should it be static?

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191130012828.14504-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: fsl: Handle the single hardwired chipselect case

The Freescale MPC8xxx had a special quirk for handling a
single hardwired chipselect, the case when we're using neither
GPIO nor native chip select: when inspecting the device tree
and finding zero "cs-gpios" on the device node the code would
assume we have a single hardwired chipselect that leaves the
device always selected.

This quirk is not handled by the new core code, so we need
to check the "cs-gpios" explicitly in the driver and set
pdata->max_chipselect = 1 which will later fall through to
the SPI master ->num_chipselect.

Make sure not to assign the chip select handler in this
case: there is no handling needed since the chip is always
selected, and this is what the old code did as well.

Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 0f0581b24bd0 ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr> (No tested the
Link: https://lore.kernel.org/r/20191128083718.39177-3-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

gpio: Handle counting of Freescale chipselects

We have a special quirk to handle the Freescale
nonstandard SPI chipselect GPIOs in the gpiolib-of.c
file, but it currently only handles the case where
the GPIOs are actually requested (gpiod_*get()).

We also need to handle that the SPI core attempts
to count the GPIOs before use, and that needs a
similar quirk in the OF part of the library.

Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 0f0581b24bd0 ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20191128083718.39177-2-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: fsl: Fix GPIO descriptor support

This makes the driver actually support looking up GPIO
descriptor. A coding mistake in the initial descriptor
support patch was that it was failing to turn on the very
feature it was implementing. Mea culpa.

Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 0f0581b24bd0 ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20191128083718.39177-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: dw: Correct handling of native chipselect

This patch reverts commit 6e0a32d6f376 ("spi: dw: Fix default polarity
of native chipselect").

The SPI framework always called the set_cs callback with the logic
level it desired on the chip select line, which is what the drivers
original handling supported. commit f3186dd87669 ("spi: Optionally
use GPIO descriptors for CS GPIOs") changed these symantics, but only
in the case of drivers that also support GPIO chip selects, to true
meaning apply slave select rather than logic high. This left things in
an odd state where a driver that only supports hardware chip selects,
the core would handle polarity but if the driver supported GPIOs as
well the driver should handle polarity.  At this point the reverted
change was applied to change the logic in the driver to match new
system.

This was then broken by commit 3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH
setting when using native and GPIO CS") which reverted the core back
to consistently calling set_cs with a logic level.

This fix reverts the driver code back to its original state to match
the current core code. This is probably a better fix as a) the set_cs
callback is always called with consistent symantics and b) the
inversion for SPI_CS_HIGH can be handled in the core and doesn't need
to be coded in each driver supporting it.

Fixes: 3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191127153936.29719-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: cadence: Correct handling of native chipselect

To fix a regression on the Cadence SPI driver, this patch reverts
commit 6046f5407ff0 ("spi: cadence: Fix default polarity of native
chipselect").

This patch was not the correct fix for the issue. The SPI framework
calls the set_cs line with the logic level it desires on the chip select
line, as such the old is_high handling was correct. However, this was
broken by the fact that before commit 3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH
setting when using native and GPIO CS") all controllers that offered
the use of a GPIO chip select had SPI_CS_HIGH applied, even for hardware
chip selects. This caused the value passed into the driver to be inverted.
Which unfortunately makes it look like a logical enable the chip select
value.

Since the core was corrected to not unconditionally apply SPI_CS_HIGH,
the Cadence driver, whilst using the hardware chip select, will deselect
the chip select every time we attempt to communicate with the device,
which results in failed communications.

Fixes: 3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191126164140.6240-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Add support for Intel Jasper Lake

LPSS SPI on Intel Jasper Lake is compatible with Intel Ice Lake which
follows Intel Cannon Lake. Add PCI IDs of Jasper Lake.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191125125159.15404-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

dt-bindings: spi: Convert stm32 QSPI bindings to json-schema

Convert the STM32 QSPI binding to DT schema format using json-schema

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191120194444.10540-1-benjamin.gaignard@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pic32: Retire dma_request_slave_channel_compat()

There is no reason to use the dma_request_slave_channel_compat() as no
filter function and parameter is provided.

Switch the driver to use dma_request_chan() instead and add support for
deferred probing against DMA channel.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20191121092703.30465-1-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: Fix Kconfig indentation

Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^        /\t/' -i */Kconfig

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191120133916.13595-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: mediatek: add SPI_CS_HIGH support

Change to use SPI_CS_HIGH to support spi CS polarity setting
for chips support enhance_timing.

Signed-off-by: Luhua Xu <luhua.xu@mediatek.com>
Link: https://lore.kernel.org/r/1574053037-26721-2-git-send-email-luhua.xu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: st-ssc4: add missed pm_runtime_disable

The driver forgets to call pm_runtime_disable in probe failure
and remove.
Add the missed calls to fix it.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191118024848.21645-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: tegra20-slink: add missed clk_unprepare

The driver misses calling clk_unprepare in probe failure and remove.
Add the calls to fix it.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191115083122.12278-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: tegra20-slink: Use dma_request_chan() directly for channel request

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20191113094256.1108-10-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: tegra114: Use dma_request_chan() directly for channel request

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20191113094256.1108-9-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: s3c64xx: Use dma_request_chan() directly for channel request

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Andi Shyti <andi@etezian.org>
Link: https://lore.kernel.org/r/20191113094256.1108-8-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: qup: Use dma_request_chan() directly for channel request

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113094256.1108-7-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pl022: Use dma_request_chan() directly for channel request

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191113094256.1108-6-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: imx: Use dma_request_chan() directly for channel request

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113094256.1108-5-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: fsl-lpspi: Use dma_request_chan() directly for channel request

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113094256.1108-4-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: atmel: Use dma_request_chan() directly for channel request

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20191113094256.1108-3-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: at91-usart: Use dma_request_chan() directly for channel request

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20191113094256.1108-2-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: Fix regression to return zero on success instead of positive value

Commit d948e6ca1899 ("spi: add power control when set_cs") added generic
runtime PM handling, but also changed the return value to be 1 instead
of 0 that we had earlier as pm_runtime_get functions return a positve
value on success.

This causes SPI devices to return errors for cases where they do:

ret = spi_setup(spi);
if (ret)
return ret;

As in many cases the SPI devices do not check for if (ret < 0).

Let's fix this by setting the status to 0 on succeess after the
runtime PM calls. Let's not return 0 at the end of the function
as this might break again later on if the function changes and
starts returning status again.

Fixes: d948e6ca1899 ("spi: add power control when set_cs")
Cc: Luhua Xu <luhua.xu@mediatek.com>
Cc: wsd_upstream@mediatek.com
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20191111195334.44833-1-tony@atomide.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Add missed security checks

pxa2xx_spi_init_pdata misses checks for devm_clk_get and
platform_get_irq.
Add checks for them to fix the bugs.

Since ssp->clk and ssp->irq are used in probe, they are mandatory here.
So we cannot use _optional() for devm_clk_get and platform_get_irq.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191109080943.30428-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: nxp-fspi: Use devm API to fix missed unregistration of controller

This driver forgets to unregister controller when remove.
Use devm API to unregister it automatically to fix it.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191109075517.29988-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: omap2-mcspi: Remove redundant checks

Both omap2_mcspi_tx_dma() and omap2_mcspi_rx_dma() are only called from
omap2_mcspi_txrx_dma() and omap2_mcspi_txrx_dma() is always called after
making sure that mcspi_dma->dma_rx and mcspi_dma->dma_tx are not NULL
(see omap2_mcspi_transfer_one()).
Therefore remove redundant NULL checks for omap2_mcspi->dma_tx and
omap2_mcspi->dma_rx pointers in omap2_mcspi_tx_dma() and
omap2_mcspi_rx_dma() respectively.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20191109041827.26934-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: zynq-qspi: Support two chip selects

The Zynq QSPI controller features 2 CS. When the num-cs DT property
is set to 2, the hardware will be initialized to support having two
devices connected over each CS.

In this case, both CS lines are driven by the state of the U_PAGE
(upper page) bit. When unset, the lower page (CS0) is selected,
otherwise it is the upper page (CS1).

Change tested on a custom design featuring two SPI-NORs with different
CS on the Zynq-7000 QSPI bus.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-8-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: zynq-qspi: Do the actual hardware initialization later in the probe

Supporting more than one CS will need some tweaking of the linear
configuration register which is (rightfully) initialized in the
hardware initialization helper. The extra initialization needs the
knowledge of the actual number of CS, which is retrieved by reading
the value of the num-cs DT property.

As the initialization helper is called pretty early and might be
called much later in the probe without side effect, let's delay it a
bit so that the number of CS will be available when running this
helper. This way, adding support for multiple CS lines in a next patch
will be eased.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-7-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: zynq-qspi: Clarify the select chip function

The code used to assert and de-assert a chip select line is very
complicated for no reason. Simplify the logic by either setting or
resetting the concerned bit, which actually only changes an electrical
state.

Update the comment to reflect that there is no possibility to actually
choose a CS as the default (CS0) will be driven in any case.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-6-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: zynq-qspi: Enhance the Linear CFG bit definitions

Using masks makes sense when manipulating fields of several bits. When
only one bit is involved, it is usual to just use the BIT() macro but
in this case using the term mask is abusive. Fix the #define macros
and their comments.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-5-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: zynq-qspi: Keep the bitfields naming consistent

Most of the bits/bitfields #define'd in this driver are composed with:
1/ the driver prefix
2/ the name of the register they apply to

Keep the naming consistent by applying this rule to the CONFIG register
internals. These definitions will be used in a following change set.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-4-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: zynq-qspi: Anything else than CS0 is not supported yet

Unlike what the driver is currently advertizing, CS0 only can be used,
CS1 is not supported at all. Prevent people to use CS1.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-2-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: zynq-qspi: Keep the naming consistent across the driver

In this driver (and also in a lot of other drivers in drivers/spi/),
the spi_controller structure is sometimes referred as 'ctlr' and
sometimes as 'ctrl'. Grepping there shows that 'ctlr' seems to be more
common so keep the naming consistent in this driver and s/ctrl/ctlr/.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108105920.19014-3-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: spi-mem: fallback to using transfers when CS gpios are used

Devices with chip selects driven via GPIO are not compatible with the
spi-mem operations. Fallback to using standard spi transfers when the
device is connected with a gpio CS.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191107044235.4864-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: bcm-qspi: Convert to use CS GPIO descriptors

Set use_gpio_descriptors to true and avoid asserting the native chip
select if the spi core has done it for us.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191107044235.4864-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: img-spfi: fix potential double release

The channels spfi->tx_ch and spfi->rx_ch are not set to NULL after they
are released. As a result, they will be released again, either on the
error handling branch in the same function or in the corresponding
remove function, i.e. img_spfi_remove(). This patch fixes the bug by
setting the two members to NULL.

Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/1573007769-20131-1-git-send-email-bianpan2016@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: add power control when set_cs

As to set_cs takes effect immediately, power spi
is needed when setup spi.

Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Luhua Xu <luhua.xu@mediatek.com>
Link: https://lore.kernel.org/r/1572426234-30019-1-git-send-email-luhua.xu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: zynq-qspi: Drop GPIO header

This driver does not use any symbols from the legacy GPIO
header so drop the include.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191030073624.23974-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: dw: Drop GPIO header

The DW driver does not use the legacy GPIO header so drop
it from the spi-dw.h include.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191030073418.23717-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: txx9: Convert to use GPIO descriptors

This converts the TXX9 SPI driver to use GPIO descriptors
to control the GPIO chip selects.

As the driver was clearly (ab)using the device tree "reg"
property to offset into the global GPIO chip we have to
add a hack to counter the hack: add a 1-to-1 chip select
to GPIO offset mapping for all 16 lines on the TXX9 GPIO
chip. The details are described in a largeish comment
in the patch.

We do not need to set up the GPIO as output any more since
the core will take care of this, as well as it will handle
the polarity inversion semantics.

Cc: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191030073832.24038-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: dw: Remove runtime PM enable/disable from common part of the driver

Committed version of the commit b9fc2d207e54 ("spi: dw: Move runtime PM
enable/disable from common to platform driver part") does not include by
some reason changes to drivers/spi/spi-dw.c that were part of the original
patch sent to the mailing list.

Complete the code move by doing those changes now.

Fixes: b9fc2d207e54 ("spi: dw: Move runtime PM enable/disable from common to platform driver part")
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191030113137.15459-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: sprd: adi: Set BIT_WDG_NEW bit when rebooting

When rebooting system, the PMIC watchdog time loading may not be loaded
correctly when another system is feeding the PMIC watchdog, since we did
not check the watchdog busy status before loading time values.

Thus we should set the BIT_WDG_NEW bit before loading time values, that
can support multiple loads without checking busy status to make sure the
time values can be loaded successfully to avoid this potential issue.

Signed-off-by: Lingling Xu <ling_ling.xu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/5655318a7252c9ea518c2f7950a61228ab8f42bf.1572257085.git.baolin.wang@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: sprd: adi: Add missing lock protection when rebooting

When rebooting the system, we should lock the watchdog after
configuration to make sure the watchdog can reboot the system
successfully.

Signed-off-by: Lingling Xu <ling_ling.xu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/7b04711127434555e3a1a86bc6be99860cd86668.1572257085.git.baolin.wang@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Introduce temporary variables to increase readability

The current conditional for PCI ID matching is hard to read.
Introduce couple of temporary variables to increase readability
of the code.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191021103625.4250-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: xilinx: Add DT support for selecting transfer word width

This core supports either 8, 16 or 32 bits as word width. This value is only
settable on instantiation, and thus we need to support any of them by means
of the device tree.

Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Link: https://lore.kernel.org/r/20191024110757.25820-3-alvaro.gamez@hazent.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: xilinx: add description of new property xlnx,num-transfer-bits

This property is used to set the number of bits per transfer (bits_per_word).

Xilinx' IP core allows either 8, 16 or 32, and is non changeable on runtime,
only when instantiating the core.

Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Link: https://lore.kernel.org/r/20191024110757.25820-2-alvaro.gamez@hazent.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: Fix spelling in the comments

Two spelling mistakes are being fixed.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191023121643.25237-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: document CS setup, hold & inactive times in header

This change documents the CS setup, host & inactive times. They were
omitted when the fields were added, and were caught by one of the build
bots.

Fixes: 25093bdeb6bc ("spi: implement SW control for CS times")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20191023070046.12478-1-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: dw-pci: Fix Chip Select amount on Intel Elkhart Lake PSE SPI

Intel(R) Programmable Services Engine (Intel(R) PSE) SPI controllers in
Intel Elkhart Lake have two Chip Select signals instead of one.

Reported-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191018132131.31608-3-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: dw-pci: Add runtime power management support

Implement pm_runtime hooks at pci driver.

Signed-off-by: Raymond Tan <raymond.tan@intel.com>
[jarkko.nikula@linux.intel.com: Forward ported on top of
commit 1e6959832510 ("spi: dw: Add basic runtime PM support")]
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191018132131.31608-2-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: atmel: Improve CS0 case support on AT91RM9200

Thanks to the recent change in this driver, it is now possible to
prevent using the CS0 with GPIO during setup. It then allows to remove
the special handling of this case in the cs_activate() and
cs_deactivate() functions.

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-8-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: atmel: Improve and fix GPIO CS usage

In the previous implementation of this driver, the index of the GPIO
used as CS was linked to the offset of the CS register used to
configure the transfer.

With this new implementation the first CS register not used by
internal CS is associated to all the GPIO CS. It allows to not be
anymore limited to have only 4 CS managed, now it is possible to have
in the same time until 3 internal CS and no more limit for the CS
GPIO.

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-7-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: atmel: Remove platform data support

This driver is now only used through the device tree. Simplify code
by explicitly depend on device tree.

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-6-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: atmel: Remove useless private field

Since the conversion to GPIO descriptor, the GPIO used as chip select,
can be directly access from the spi_device struct. So there is no need
to keep the field npcs_pin.

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-5-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: atmel: Configure GPIO per CS instead of by controller

Instead of setting up the GPIO configuration for the whole controller,
do it at CS level. It will allow to mix internal CS and GPIO CS, which
is not possible with the current implementation.

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-4-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: atmel: Fix CS high support

Until a few years ago, this driver was only used with CS GPIO. The
only exception is CS0 on AT91RM9200 which has to use internal CS. A
limitation of the internal CS is that they don't support CS High.

So by using the CS GPIO the CS high configuration was available except
for the particular case CS0 on RM9200.

When the support for the internal chip-select was added, the check of
the CS high support was not updated. Due to this the driver accepts
this configuration for all the SPI controller v2 (used by all SoCs
excepting the AT91RM9200) whereas the hardware doesn't support it for
infernal CS.

This patch fixes the test to match the hardware capabilities.

Fixes: 4820303480a1 ("spi: atmel: add support for the internal chip-select of the spi controller")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-3-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: atmel: Remove and fix erroneous comments

Since CSAAT functionality support has been added. Some comments become
wrong. Fix them to match the current driver behavior.

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-2-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Replace of_device.h with mod_devicetable.h and of.h

There is nothing in use from of_device.h. The definitions and macros
are available thru mod_devicetable.h and of.h.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191018105429.82782-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Convert to use device_get_match_data()

Convert to use device_get_match_data() instead of open coded variant.

While here, switch of_property_read_bool() to device_property_read_bool().

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191018105429.82782-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Convert pxa2xx_spi_get_port_id() to take struct device

This is preparatory patch before converting to use device_get_match_data() API.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191018105429.82782-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Sort headers

Sort the headers in alphabetic order in order to ease the maintenance
for this part.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191018105429.82782-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: No need to keep pointer to platform device

There is no need to keep a pointer to the platform device. Currently there are
no users of it directly, and if there will be in the future we may restore it
from pointer to the struct device.

Convert all users at the same time.

Cc: Russell King <linux@armlinux.org.uk>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191018105429.82782-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: use new `spi_transfer_delay_exec` helper where straightforward

For many places in the spi drivers, using the new `spi_transfer_delay`
helper is straightforward.
It's just replacing:
```
  if (t->delay_usecs)
     udelay(t->delay_usecs);
```
with `spi_transfer_delay(t)` which handles both `delay_usecs` and the new
`delay` field.

This change replaces in all places (in the spi drivers)  where this change
is simple.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-10-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: spi-axi: extend support for the `delay` field

The AXI SPI engine driver uses the `delay_usecs` field from `spi_transfer`
to configure delays, which the controller will execute.
This change extends the logic to also include the `delay` value, in case it
is used (instead if `delay_usecs`).

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-20-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: bcm63xx: extend error condition to `delay` as well

The driver errors out if `delay_usecs` is non-zero. This error condition
should be extended to the new `delay` field, to account for when it will be
used.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-19-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: spi-falcon: extend warning to `delay` as well

The WARN_ON macro prints a warning in syslog if `delay_usecs` is non-zero.
However, with the new intermediate `delay`, the warning should also be
printed.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-18-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: spi-fsl-espi: convert transfer delay to `spi_delay` format

The way the max delay is computed for this controller, it looks like it is
searching for the max delay from an SPI message a using that.

No idea if this is valid. But this change should support both `delay_usecs`
and the new `delay` data which is of `spi_delay` type.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-17-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: implement SW control for CS times

This change implements CS control for setup, hold & inactive delays.

The `cs_setup` delay is completely new, and can help with cases where
asserting the CS, also brings the device out of power-sleep, where there
needs to be a longer (than usual), before transferring data.

The `cs_hold` time can overlap with the `delay` (or `delay_usecs`) from an
SPI transfer. The main difference is that `cs_hold` implies that CS will be
de-asserted.

The `cs_inactive` delay does not have a clear use-case yet. It has been
implemented mostly because the `spi_set_cs_timing()` function implements
it. To some degree, this could overlap or replace `cs_change_delay`, but
this will require more consideration/investigation in the future.

All these delays have been added to the `spi_controller` struct, as they
would typically be configured by calling `spi_set_cs_timing()` after an
`spi_setup()` call.

Software-mode for CS control, implies that the `set_cs_timing()` hook has
not been provided for the `spi_controller` object.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-16-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: tegra114: change format for `spi_set_cs_timing()` function

The initial version of `spi_set_cs_timing()` was implemented with
consideration only for clock-cycles as delay.

For cases like `CS setup` time, it's sometimes needed that micro-seconds
(or nano-seconds) are required, or sometimes even longer delays, for cases
where the device needs a little longer to start transferring that after CS
is asserted.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-15-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: spidev: use new `delay` field for spi transfers

The `delay` field has type `struct spi_delay`.
This allows users to specify nano-second or clock-cycle delays (if needed).

Converting to use `delay` is straightforward: it's just assigning the
value to `delay.value` and hard-coding the `delay.unit` to
`SPI_DELAY_UNIT_USECS`.

This keeps the uapi for spidev un-changed. Changing it can be part of
another changeset and discussion.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-14-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: spi-loopback-test: use new `delay` field

This change replaces the use of the `delay_usecs` field with the new
`delay` field. The code/test still uses micro-seconds, but they are now
configured and used via the `struct spi_delay` format of the `delay` field.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-13-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: tegra20-sflash: use to new `spi_transfer_delay_exec`

This conversion to the spi_transfer_delay_exec() helper is not
straightforward, as it seems that when a delay is present, the controller
issues a command, and then a delay is followed.

This change adds support for the new `delay` field which is of type
`spi_delay` and keeps backwards compatibility with the old `delay_usecs`
field.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-12-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: tegra114: use `spi_transfer_delay_exec` helper

The tegra114 driver has a weird/separate `tegra_spi_transfer_delay()`
function that does 2 delays: one mdelay() and one udelay().

This was introduced via commit f4fade12d506e14867a2b0a5e2f7aaf227297d8b
("spi/tegra114: Correct support for cs_change").

There doesn't seem to be a mention in that commit message to suggest a
specific need/use-case for having the 2 delay calls.
For the most part, udelay() should be sufficient.

This change replaces it with the new `spi_transfer_delay_exec()`, which
should do the same thing.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-11-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: introduce `delay` field for `spi_transfer` + spi_transfer_delay_exec()

The change introduces the `delay` field to the `spi_transfer` struct as an
`struct spi_delay` type.
This intends to eventually replace `delay_usecs`.

But, since there are many users of `delay_usecs`, this needs some
intermediate work.
A helper called `spi_transfer_delay_exec()` is also added, which maintains
backwards compatibility with `delay_usecs`, by assigning the value to
`delay` if non-zero.
This should maintain backwards compatibility with current users of
`udelay_usecs`.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-9-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: core,atmel: convert `word_delay_usecs` -> `word_delay` for spi_device

This change does a conversion from the `word_delay_usecs` -> `word_delay`
for the `spi_device` struct.

This allows users to specify inter-word delays in other unit types
(nano-seconds or clock cycles), depending on how users want.

The Atmel SPI driver is the only current user of the `word_delay_usecs`
field (from the `spi_device` struct).
So, it needed a slight conversion to use the `word_delay` as an `spi_delay`
struct.

In SPI core, the only required mechanism is to update the `word_delay`
information per `spi_transfer`. This requires a bit more logic than before,
because it needs that both delays be converted to a common unit
(nano-seconds) for comparison.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-8-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: spidev: use new `word_delay` field for spi transfers

The `word_delay` field had it's type changed to `struct spi_delay`.
This allows users to specify nano-second or clock-cycle delays (if needed).

Converting to use `word_delay` is straightforward: it's just assigning the
value to `word_delay.value` and hard-coding the `word_delay.unit` to
`SPI_DELAY_UNIT_USECS`

This keeps the uapi for spidev un-changed. Changing it can be part of
another changeset and discussion.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-7-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: orion: use new `word_delay` field for SPI transfers

The `word_delay` field had it's type changed to `struct spi_delay`.
This allows users to specify nano-second or clock-cycle delays (if needed).

Converting to use `word_delay` is straightforward: it just uses the new
`spi_delay_exec()` routine, that handles the `unit` part.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-6-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: sprd: convert transfer word delay to spi_delay struct

The Spreadtrum SPI driver is the only user of the `word_delay` field in
the `spi_transfer` struct.

This change converts the field to use the `spi_delay` struct. This also
enforces the users to specify the delay unit to be `SPI_DELAY_UNIT_SCK`.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-5-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: make `cs_change_delay` the first user of the `spi_delay` logic

Since the logic for `spi_delay` struct + `spi_delay_exec()` has been copied
from the `cs_change_delay` logic, it's natural to make this delay, the
first user.

The `cs_change_delay` logic requires that the default remain 10 uS, in case
it is unspecified/unconfigured. So, there is some special handling needed
to do that.

The ADIS library is one of the few users of the new `cs_change_delay`
parameter for an spi_transfer.

The introduction of the `spi_delay` struct, requires that the users of of
`cs_change_delay` get an update. This change also updates the ADIS library.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-4-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: introduce spi_delay struct as "value + unit" & spi_delay_exec()

There are plenty of delays that have been introduced in SPI core. Most of
them are in micro-seconds, some need to be in nano-seconds, and some in
clock-cycles.

For some of these delays (related to transfers & CS timing) it may make
sense to have a `spi_delay` struct that abstracts these a bit.

The important element of these delays [for unification] seems to be the
`unit` of the delay.
It looks like micro-seconds is good enough for most people, but every-once
in a while, some delays seem to require other units of measurement.

This change adds the `spi_delay` struct & a `spi_delay_exec()` function
that processes a `spi_delay` object/struct to execute the delay.
It's a copy of the `cs_change_delay` mechanism, but without the default
for 10 uS.

The clock-cycle delay unit is a bit special, as it needs to be bound to an
`spi_transfer` object to execute.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-3-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: move `cs_change_delay` backwards compat logic outside switch

The `cs_change_delay` backwards compatibility value could be moved outside
of the switch statement.
The only reason to do it, is to make the next patches easier to diff.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-2-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

dt-bindings: spi: sh-msiof: Add r8a774b1 support

Document RZ/G2N (R8A774B1) SoC bindings.

Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1570178133-21532-3-git-send-email-fabrizio.castro@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

dt-bindings: spi: sh-msiof: Convert bindings to json-schema

Convert Renesas HSPI bindings documentation to json-schema.
Also name bindings documentation file according to the compat string
being documented.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20190926102533.17829-1-horms+renesas@verge.net.au
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: npcm: Remove set but not used variable 'val'

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/spi/spi-npcm-pspi.c: In function npcm_pspi_handler:
drivers/spi/spi-npcm-pspi.c:296:6: warning: variable val set but not used [-Wunused-but-set-variable]

It is not used since commit 2a22f1b30cee ("spi:
npcm: add NPCM PSPI controller driver")

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Link: https://lore.kernel.org/r/1570581437-104549-3-git-send-email-zhengbin13@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: omap-100k: Remove set but not used variable 'dataH'

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/spi/spi-omap-100k.c: In function spi100k_read_data:
drivers/spi/spi-omap-100k.c:140:6: warning: variable dataH set but not used [-Wunused-but-set-variable]

It is not used since commit 35c9049b2704 ("Add OMAP spi100k driver")

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Link: https://lore.kernel.org/r/1570581437-104549-2-git-send-email-zhengbin13@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge branch 'for-5.4' of https://git./linux/kernel/git/broonie/spi into spi-5.5