Dave Stevenson [Tue, 15 Jun 2021 17:38:46 +0000 (18:38 +0100)]
media: i2c: imx258: Remove redundant I2C writes.
Registers 0x0202 and 0x0203 are written via the control handler
for V4L2_CID_EXPOSURE, so are not needed from the mode lists.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Tue, 15 Jun 2021 17:29:52 +0000 (18:29 +0100)]
media: i2c: imx258: Implement HFLIP and VFLIP controls.
The sensor supports H & V flips, so implement the relevant controls.
Note that the Bayer order changes with these flips, therefore
they set the V4L2_CTRL_FLAG_MODIFY_LAYOUT property.
As we now support flips, remove the restriction of the sensor only
probing if rotated 180 degrees, but do take that value and initialise
VFLIP and HFLIP based on it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Wed, 30 Mar 2022 13:55:01 +0000 (14:55 +0100)]
media: i2c: imx258: Disable digital cropping on binned modes
The binned modes set DIG_CROP_X_OFFSET and DIG_CROP_IMAGE_WIDTH
to less than the full image, even though the image being captured
is meant to be a scaled version of the full array size.
Reduce X_OFFSET to 0, and increase IMAGE_WIDTH to the full array.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Tue, 15 Jun 2021 17:34:38 +0000 (18:34 +0100)]
media: i2c: imx258: Make image geometry meet sensor requirements
The output image is defined as being 4208x3118 pixels in size.
Y_ADD_STA register was set to 0, and Y_ADD_END to 3118, giving
3119 lines total.
The datasheet lists a requirement for Y_ADD_STA to be a multiple
of a power of 2 depending on binning/scaling mode (2 for full pixel,
4 for x2-bin/scale, 8 for (x2-bin)+(x2-subsample) or x4-bin, or 16
for (x4-bin)+(x2-subsample)).
(Y_ADD_END – Y_ADD_STA + 1) also has to be a similar power of 2.
The current configuration for the full res modes breaks that second
requirement, and we can't increase Y_ADD_STA to 1 to retain exactly
the same field of view as that then breaks the first requirement.
For the binned modes, they are worse off as 3118 is not a multiple of
4.
Increase the main mode to 4208x3120 so that it is the same FOV as the
binned modes, with Y_ADD_STA at 0.
Fix Y_ADD_STA and Y_ADD_END for the binned modes so that they meet the
sensor requirements.
This does change the Bayer order as the default configuration is for
H&V flips to be enabled, so readout is from Y_STA_END to Y_ADD_STA,
and this patch has changed Y_STA_END.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Tue, 15 Jun 2021 17:18:42 +0000 (18:18 +0100)]
media: i2c: imx258: Remove unused defines
The IMX258_FLL_* defines are unused. Remove them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dom Cobley [Wed, 6 Apr 2022 19:35:13 +0000 (20:35 +0100)]
drm/vc4_hdmi: Force modeset when bpc changes
See: https://forum.libreelec.tv/thread/25427-le-10-0-2-on-rpi4-not-playing-files-that-10-0-1-had-no-problems-with/
The issue is that kodi changes hdmi mode to 3840x2160@24 initially with "max bcp=8"
After decoding the first frame it changes property to "max bpc=12".
Now vc4_hdmi_encoder_compute_config chooses vc4_state->output_bpc = 12 with output_format=VC4_HDMI_OUTPUT_RGB
This requires scrambling as clock > 300MHz (and we have hdmi_enable_4kp60=1).
vc4_hdmi_encoder_atomic_mode_set (without this PR's assignment to mode_changed) is currenly not called so we don't assign:
vc4_hdmi->output_bpc = vc4_state->output_bpc
which means vc4_hdmi_enable_scrambling never enables scrambling (as vc4_hdmi->output_bpc is still 8).
But we do set the pixel clock in phy_init() to a clock frequency that requires scrambling.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Maxime Ripard [Thu, 31 Mar 2022 13:27:43 +0000 (15:27 +0200)]
Revert "drm/vc4: hvs: Defer dlist slots deallocation"
This reverts commit
e99a1b69da07ee3b89a6b8005b854e6c04bfb450.
Daniel Vetter [Fri, 23 Oct 2020 12:39:23 +0000 (14:39 +0200)]
drm/atomic-helpers: remove legacy_cursor_update hacks
The stuff never really worked, and leads to lots of fun because it
out-of-order frees atomic states. Which upsets KASAN, among other
things.
For async updates we now have a more solid solution with the
->atomic_async_check and ->atomic_async_commit hooks. Support for that
for msm and vc4 landed. nouveau and i915 have their own commit
routines, doing something similar.
For everyone else it's probably better to remove the use-after-free
bug, and encourage folks to use the async support instead. The
affected drivers which register a legacy cursor plane and don't either
use the new async stuff or their own commit routine are: amdgpu,
atmel, mediatek, qxl, rockchip, sti, sun4i, tegra, virtio, and vmwgfx.
Inspired by an amdgpu bug report.
v2: Drop RFC, I think with amdgpu converted over to use
atomic_async_check/commit done in
commit
674e78acae0dfb4beb56132e41cbae5b60f7d662
Author: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Date: Wed Dec 5 14:59:07 2018 -0500
drm/amd/display: Add fast path for cursor plane updates
we don't have any driver anymore where we have userspace expecting
solid legacy cursor support _and_ they are using the atomic helpers in
their fully glory. So we can retire this.
v3: Paper over msm and i915 regression. The complete_all is the only
thing missing afaict.
v4: Rebased on recent kernel, added extra link for vc4 bug.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199425
Link: https://lore.kernel.org/all/20220221134155.125447-9-maxime@cerno.tech/
Cc: mikita.lipski@amd.com
Cc: Michel Dänzer <michel@daenzer.net>
Cc: harry.wentland@amd.com
Cc: Rob Clark <robdclark@gmail.com>
Cc: "Kazlauskas, Nicholas" <nicholas.kazlauskas@amd.com>
Tested-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Phil Elwell [Sun, 3 Apr 2022 14:27:46 +0000 (15:27 +0100)]
configs: Re-enable all GSPCA camera modules
The GSPCA camera modules were lost due to change in a default value
- when has that happened before?
See: https://github.com/raspberrypi/linux/issues/4977
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
6by9 [Fri, 1 Apr 2022 10:31:38 +0000 (11:31 +0100)]
drm/vc4: Force trigger of dlist update on margins change (#4970)
When the margins are changed, the dlist needs to be regenerated
with the changed updated dest regions for each of the planes.
Setting the zpos_changed flag is sufficient to trigger that
without doing a full modeset, therefore set it should the
margins be changed.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Phil Elwell [Thu, 31 Mar 2022 16:55:51 +0000 (17:55 +0100)]
brcmfmac: Restore ISO3166 and 0 rev as a fallback
Commit
b0b524f079a2 ("brcmfmac: use ISO3166 country code and 0 rev
as fallback") was a welcome addition for Raspberry Pi as it replaced
an equivalent bit of downstream code. Commit
151a7c12c4fc reverted
it because it broke BCM4359/9 devices.
This is a renamed reversion of the reversion.
See: https://github.com/raspberrypi/Raspberry-Pi-OS-64bit/issues/217
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Dave Stevenson [Thu, 31 Mar 2022 11:05:04 +0000 (12:05 +0100)]
drm/panel: panel-ilitek9881c: Add prepare_upstream_first flag
The panel sends MIPI DCS commands during prepare and is expecting
the bus to remain in LP-11 state in-between.
Set the prepare_upstream_first flag so that the upstream DSI host
is prepared / pre_enabled first, and therefore the bus is in a
defined state.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 31 Mar 2022 11:03:36 +0000 (12:03 +0100)]
drm/panel: ilitek-ili9881c: Clean up on mipi_dsi_attach failure
mipi_dsi_attach is allowed to fail, and currently the probe
code doesn't clean up (mainly drm_panel_remove) if this happens.
Add cleanup code on failure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Ben Avison [Wed, 30 Mar 2022 10:43:25 +0000 (11:43 +0100)]
ARM: dts: Enable PMU on Cortex-A72 in AArch32 state
There is no specific AArch32 driver for the Cortex-A72 PMU, but the
Cortex-A7 one works and is much better than no PMU driver at all.
Signed-off-by: Ben Avison <bavison@riscosopen.org>
Dom Cobley [Wed, 30 Mar 2022 16:00:25 +0000 (17:00 +0100)]
Merge remote-tracking branch 'stable/linux-5.15.y' into rpi-5.15.y
Phil Elwell [Wed, 30 Mar 2022 08:48:41 +0000 (09:48 +0100)]
pinctrl: bcm2835: Only return non-GPIOs to inputs
Allowing GPIO state to persist allows the use of gpioset to control
GPIO levels without having to use the --mode=wait feature.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
David Plowman [Tue, 29 Mar 2022 15:10:06 +0000 (16:10 +0100)]
mm,page_alloc,cma: introduce a customisable threshold for allocating pages in cma
On some platforms the cma area can be half the entire system memory,
meaning that allocations start happening in the cma area immediately.
This leads to fragmentation and subsequent fatal cma_alloc failures.
We introduce an "alloc_in_cma_threshold" parameter which requires that
this many sixteenths of the free pages must be in cma before it will
try to use them. By default this is set to 12, but the previous
behaviour can be restored by setting it to 8 on startup.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Dave Stevenson [Mon, 28 Mar 2022 10:52:48 +0000 (11:52 +0100)]
bcm2835-codec: Return empty buffers to the VPU instead of queueing to vbuf2
The encoder can skip frames totally should rate control overshoot
the target bitrate too far. In this situation it generates an
output buffer of length 0.
V4L2 treats a buffer of length 0 as an end of stream flag, which is
not appropriate in this case, therefore we can not return that buffer
to the client.
The driver was returning the buffer to videobuf2 in the QUEUED state,
however that buffer was then not dequeued again, so the number of
buffers was reduced each time this happened. In the pathological
case of using GStreamer's videotestsrc in mode 1 for noise, this happens
sufficiently frequently to totally stall the pipeline.
If the port is still enabled then return the buffer straight back to
the VPU rather than to videobuf2.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Noralf Trønnes [Sun, 27 Mar 2022 16:54:17 +0000 (18:54 +0200)]
overlays/rpi-display: Add support for DRM driver
Add a "drm" parameter that enables use of the drm/mi0283qt driver instead
of fbtft/fb_ili9341. Also add a "backlight-pwm" parameter that can be used
with the "drm" parameter.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Noralf Trønnes [Sat, 26 Mar 2022 17:59:27 +0000 (18:59 +0100)]
Revert "update rpi-display-overlay.dts pins for 5.10+"
This reverts commit
97d1b136be6dbc81316259690fd15b4110a3606f.
The fbtft backlight problem was fixed in 5.15.6 so this workaround has to
be reverted to make backlight work again.
Ref: https://github.com/notro/fbtft/issues/571
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Greg Kroah-Hartman [Mon, 28 Mar 2022 07:58:46 +0000 (09:58 +0200)]
Linux 5.15.32
Link: https://lore.kernel.org/r/20220325150419.931802116@linuxfoundation.org
Tested-by: Fox Chen <foxhlchen@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Ron Economos <re@w6rz.net>
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Fri, 25 Mar 2022 03:58:27 +0000 (20:58 -0700)]
llc: only change llc->dev when bind() succeeds
commit
2d327a79ee176930dc72c131a970c891d367c1dc upstream.
My latest patch, attempting to fix the refcount leak in a minimal
way turned out to add a new bug.
Whenever the bind operation fails before we attempt to grab
a reference count on a device, we might release the device refcount
of a prior successful bind() operation.
syzbot was not happy about this [1].
Note to stable teams:
Make sure commit
b37a46683739 ("netdevice: add the case if dev is NULL")
is already present in your trees.
[1]
general protection fault, probably for non-canonical address 0xdffffc0000000070: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000380-0x0000000000000387]
CPU: 1 PID: 3590 Comm: syz-executor361 Tainted: G W 5.17.0-syzkaller-04796-g169e77764adc #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:llc_ui_connect+0x400/0xcb0 net/llc/af_llc.c:500
Code: 80 3c 02 00 0f 85 fc 07 00 00 4c 8b a5 38 05 00 00 48 b8 00 00 00 00 00 fc ff df 49 8d bc 24 80 03 00 00 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 a9 07 00 00 49 8b b4 24 80 03 00 00 4c 89 f2 48
RSP: 0018:
ffffc900038cfcc0 EFLAGS:
00010202
RAX:
dffffc0000000000 RBX:
ffff8880756eb600 RCX:
0000000000000000
RDX:
0000000000000070 RSI:
ffffc900038cfe3e RDI:
0000000000000380
RBP:
ffff888015ee5000 R08:
0000000000000001 R09:
ffff888015ee5535
R10:
ffffed1002bdcaa6 R11:
0000000000000000 R12:
0000000000000000
R13:
ffffc900038cfe37 R14:
ffffc900038cfe38 R15:
ffff888015ee5012
FS:
0000555555acd300(0000) GS:
ffff8880b9d00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000020000280 CR3:
0000000077db6000 CR4:
00000000003506e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
<TASK>
__sys_connect_file+0x155/0x1a0 net/socket.c:1900
__sys_connect+0x161/0x190 net/socket.c:1917
__do_sys_connect net/socket.c:1927 [inline]
__se_sys_connect net/socket.c:1924 [inline]
__x64_sys_connect+0x6f/0xb0 net/socket.c:1924
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f016acb90b9
Code: 28 c3 e8 2a 14 00 00 66 2e 0f 1f 84 00 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:
00007ffd417947f8 EFLAGS:
00000246 ORIG_RAX:
000000000000002a
RAX:
ffffffffffffffda RBX:
0000000000000000 RCX:
00007f016acb90b9
RDX:
0000000000000010 RSI:
0000000020000140 RDI:
0000000000000003
RBP:
00007f016ac7d0a0 R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000246 R12:
00007f016ac7d130
R13:
0000000000000000 R14:
0000000000000000 R15:
0000000000000000
</TASK>
Modules linked in:
---[ end trace
0000000000000000 ]---
RIP: 0010:llc_ui_connect+0x400/0xcb0 net/llc/af_llc.c:500
Fixes:
764f4eb6846f ("llc: fix netdevice reference leaks in llc_ui_bind()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: 赵子轩 <beraphin@gmail.com>
Cc: Stoyan Manolov <smanolov@suse.de>
Link: https://lore.kernel.org/r/20220325035827.360418-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann [Mon, 14 Feb 2022 14:48:14 +0000 (15:48 +0100)]
nds32: fix access_ok() checks in get/put_user
commit
8926d88ced46700bf6117ceaf391480b943ea9f4 upstream.
The get_user()/put_user() functions are meant to check for
access_ok(), while the __get_user()/__put_user() functions
don't.
This broke in 4.19 for nds32, when it gained an extraneous
check in __get_user(), but lost the check it needs in
__put_user().
Fixes:
487913ab18c2 ("nds32: Extract the checking and getting pointer to a macro")
Cc: stable@vger.kernel.org @ v4.19+
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann [Tue, 15 Feb 2022 16:59:41 +0000 (17:59 +0100)]
m68k: fix access_ok for coldfire
commit
26509034bef198525d5936c116cbd0c3fa491c0b upstream.
While most m68k platforms use separate address spaces for user
and kernel space, at least coldfire does not, and the other
ones have a TASK_SIZE that is less than the entire 4GB address
range.
Using the default implementation of __access_ok() stops coldfire
user space from trivially accessing kernel memory.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bryan O'Donoghue [Tue, 25 Jan 2022 00:40:46 +0000 (00:40 +0000)]
wcn36xx: Differentiate wcn3660 from wcn3620
commit
98d504a82cc75840bec8e3c6ae0e4f411921962b upstream.
The spread of capability between the three WiFi silicon parts wcn36xx
supports is:
wcn3620 - 802.11 a/b/g
wcn3660 - 802.11 a/b/g/n
wcn3680 - 802.11 a/b/g/n/ac
We currently treat wcn3660 as wcn3620 thus limiting it to 2GHz channels.
Fix this regression by ensuring we differentiate between all three parts.
Fixes:
8490987bdb9a ("wcn36xx: Hook and identify RF_IRIS_WCN3680")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220125004046.4058284-1-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Bottomley [Mon, 7 Mar 2022 20:58:03 +0000 (15:58 -0500)]
tpm: use try_get_ops() in tpm-space.c
commit
fb5abce6b2bb5cb3d628aaa63fa821da8c4600f9 upstream.
As part of the series conversion to remove nested TPM operations:
https://lore.kernel.org/all/
20190205224723.19671-1-jarkko.sakkinen@linux.intel.com/
exposure of the chip->tpm_mutex was removed from much of the upper
level code. In this conversion, tpm2_del_space() was missed. This
didn't matter much because it's usually called closely after a
converted operation, so there's only a very tiny race window where the
chip can be removed before the space flushing is done which causes a
NULL deref on the mutex. However, there are reports of this window
being hit in practice, so fix this by converting tpm2_del_space() to
use tpm_try_get_ops(), which performs all the teardown checks before
acquring the mutex.
Cc: stable@vger.kernel.org # 5.4.x
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Lüssing [Thu, 10 Mar 2022 18:35:13 +0000 (19:35 +0100)]
mac80211: fix potential double free on mesh join
commit
4a2d4496e15ea5bb5c8e83b94ca8ca7fb045e7d3 upstream.
While commit
6a01afcf8468 ("mac80211: mesh: Free ie data when leaving
mesh") fixed a memory leak on mesh leave / teardown it introduced a
potential memory corruption caused by a double free when rejoining the
mesh:
ieee80211_leave_mesh()
-> kfree(sdata->u.mesh.ie);
...
ieee80211_join_mesh()
-> copy_mesh_setup()
-> old_ie = ifmsh->ie;
-> kfree(old_ie);
This double free / kernel panics can be reproduced by using wpa_supplicant
with an encrypted mesh (if set up without encryption via "iw" then
ifmsh->ie is always NULL, which avoids this issue). And then calling:
$ iw dev mesh0 mesh leave
$ iw dev mesh0 mesh join my-mesh
Note that typically these commands are not used / working when using
wpa_supplicant. And it seems that wpa_supplicant or wpa_cli are going
through a NETDEV_DOWN/NETDEV_UP cycle between a mesh leave and mesh join
where the NETDEV_UP resets the mesh.ie to NULL via a memcpy of
default_mesh_setup in cfg80211_netdev_notifier_call, which then avoids
the memory corruption, too.
The issue was first observed in an application which was not using
wpa_supplicant but "Senf" instead, which implements its own calls to
nl80211.
Fixing the issue by removing the kfree()'ing of the mesh IE in the mesh
join function and leaving it solely up to the mesh leave to free the
mesh IE.
Cc: stable@vger.kernel.org
Fixes:
6a01afcf8468 ("mac80211: mesh: Free ie data when leaving mesh")
Reported-by: Matthias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Tested-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Link: https://lore.kernel.org/r/20220310183513.28589-1-linus.luessing@c0d3.blue
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann [Thu, 10 Feb 2022 15:24:30 +0000 (16:24 +0100)]
uaccess: fix integer overflow on access_ok()
commit
222ca305c9fd39e5ed8104da25c09b2b79a516a8 upstream.
Three architectures check the end of a user access against the
address limit without taking a possible overflow into account.
Passing a negative length or another overflow in here returns
success when it should not.
Use the most common correct implementation here, which optimizes
for a constant 'size' argument, and turns the common case into a
single comparison.
Cc: stable@vger.kernel.org
Fixes:
da551281947c ("csky: User access")
Fixes:
f663b60f5215 ("microblaze: Fix uaccess_ok macro")
Fixes:
7567746e1c0d ("Hexagon: Add user access functions")
Reported-by: David Laight <David.Laight@aculab.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul E. McKenney [Fri, 21 Jan 2022 20:40:08 +0000 (12:40 -0800)]
rcu: Don't deboost before reporting expedited quiescent state
commit
10c535787436d62ea28156a4b91365fd89b5a432 upstream.
Currently rcu_preempt_deferred_qs_irqrestore() releases rnp->boost_mtx
before reporting the expedited quiescent state. Under heavy real-time
load, this can result in this function being preempted before the
quiescent state is reported, which can in turn prevent the expedited grace
period from completing. Tim Murray reports that the resulting expedited
grace periods can take hundreds of milliseconds and even more than one
second, when they should normally complete in less than a millisecond.
This was fine given that there were no particular response-time
constraints for synchronize_rcu_expedited(), as it was designed
for throughput rather than latency. However, some users now need
sub-100-millisecond response-time constratints.
This patch therefore follows Neeraj's suggestion (seconded by Tim and
by Uladzislau Rezki) of simply reversing the two operations.
Reported-by: Tim Murray <timmurray@google.com>
Reported-by: Joel Fernandes <joelaf@google.com>
Reported-by: Neeraj Upadhyay <quic_neeraju@quicinc.com>
Reviewed-by: Neeraj Upadhyay <quic_neeraju@quicinc.com>
Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Tested-by: Tim Murray <timmurray@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Sandeep Patil <sspatil@google.com>
Cc: <stable@vger.kernel.org> # 5.4.x
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roberto Sassu [Mon, 13 Dec 2021 18:31:22 +0000 (19:31 +0100)]
drm/virtio: Ensure that objs is not NULL in virtio_gpu_array_put_free()
commit
6b79f96f4a23846516e5e6e4dd37fc06f43a60dd upstream.
If virtio_gpu_object_shmem_init() fails (e.g. due to fault injection, as it
happened in the bug report by syzbot), virtio_gpu_array_put_free() could be
called with objs equal to NULL.
Ensure that objs is not NULL in virtio_gpu_array_put_free(), or otherwise
return from the function.
Cc: stable@vger.kernel.org # 5.13.x
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reported-by: syzbot+e9072e90624a31dfa85f@syzkaller.appspotmail.com
Fixes:
377f8331d0565 ("drm/virtio: fix possible leak/unlock virtio_gpu_object_array")
Link: http://patchwork.freedesktop.org/patch/msgid/20211213183122.838119-1-roberto.sassu@huawei.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Brian Norris [Fri, 25 Feb 2022 09:44:32 +0000 (11:44 +0200)]
Revert "ath: add support for special 0x0 regulatory domain"
commit
1ec7ed5163c70a0d040150d2279f932c7e7c143f upstream.
This reverts commit
2dc016599cfa9672a147528ca26d70c3654a5423.
Users are reporting regressions in regulatory domain detection and
channel availability.
The problem this was trying to resolve was fixed in firmware anyway:
QCA6174 hw3.0: sdio-4.4.1: add firmware.bin_WLAN.RMH.4.4.1-00042
https://github.com/kvalo/ath10k-firmware/commit/
4d382787f0efa77dba40394e0bc604f8eff82552
Link: https://bbs.archlinux.org/viewtopic.php?id=254535
Link: http://lists.infradead.org/pipermail/ath10k/2020-April/014871.html
Link: http://lists.infradead.org/pipermail/ath10k/2020-May/015152.html
Link: https://lore.kernel.org/all/1c160dfb-6ccc-b4d6-76f6-4364e0adb6dd@reox.at/
Fixes:
2dc016599cfa ("ath: add support for special 0x0 regulatory domain")
Cc: <stable@vger.kernel.org>
Cc: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20200527165718.129307-1-briannorris@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Wed, 19 Jan 2022 20:18:37 +0000 (14:18 -0600)]
Bluetooth: btusb: Add one more Bluetooth part for the Realtek RTL8852AE
commit
2e7b4a328ed6ea57d22853939e69bc86c560996d upstream.
This Realtek device has both wifi and BT components. The latter reports
a USB ID of 0bda:2852, which is not in the table.
BT device description in /sys/kernel/debug/usb/devices contains the following entries:
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=2852 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=
00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
The missing USB_ID was reported by user trius65 at https://github.com/lwfinger/rtw89/issues/122
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Giovanni Cabiddu [Fri, 4 Mar 2022 17:54:47 +0000 (17:54 +0000)]
crypto: qat - disable registration of algorithms
commit
8893d27ffcaf6ec6267038a177cb87bcde4dd3de upstream.
The implementations of aead and skcipher in the QAT driver do not
support properly requests with the CRYPTO_TFM_REQ_MAY_BACKLOG flag set.
If the HW queue is full, the driver returns -EBUSY but does not enqueue
the request.
This can result in applications like dm-crypt waiting indefinitely for a
completion of a request that was never submitted to the hardware.
To avoid this problem, disable the registration of all crypto algorithms
in the QAT driver by setting the number of crypto instances to 0 at
configuration time.
Cc: stable@vger.kernel.org
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Werner Sembach [Tue, 15 Mar 2022 19:02:28 +0000 (20:02 +0100)]
ACPI: video: Force backlight native for Clevo NL5xRU and NL5xNU
commit
c844d22fe0c0b37dc809adbdde6ceb6462c43acf upstream.
Clevo NL5xRU and NL5xNU/TUXEDO Aura 15 Gen1 and Gen2 have both a working
native and video interface. However the default detection mechanism first
registers the video interface before unregistering it again and switching
to the native interface during boot. This results in a dangling SBIOS
request for backlight change for some reason, causing the backlight to
switch to ~2% once per boot on the first power cord connect or disconnect
event. Setting the native interface explicitly circumvents this buggy
behaviour by avoiding the unregistering process.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maximilian Luz [Sun, 13 Feb 2022 15:49:20 +0000 (16:49 +0100)]
ACPI: battery: Add device HID and quirk for Microsoft Surface Go 3
commit
7dacee0b9efc8bd061f097b1a8d4daa6591af0c6 upstream.
For some reason, the Microsoft Surface Go 3 uses the standard ACPI
interface for battery information, but does not use the standard PNP0C0A
HID. Instead it uses MSHW0146 as identifier. Add that ID to the driver
as this seems to work well.
Additionally, the power state is not updated immediately after the AC
has been (un-)plugged, so add the respective quirk for that.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark Cilissen [Mon, 7 Mar 2022 03:16:58 +0000 (04:16 +0100)]
ACPI / x86: Work around broken XSDT on Advantech DAC-BJ01 board
commit
e702196bf85778f2c5527ca47f33ef2e2fca8297 upstream.
On this board the ACPI RSDP structure points to both a RSDT and an XSDT,
but the XSDT points to a truncated FADT. This causes all sorts of trouble
and usually a complete failure to boot after the following error occurs:
ACPI Error: Unsupported address space: 0x20 (*/hwregs-*)
ACPI Error: AE_SUPPORT, Unable to initialize fixed events (*/evevent-*)
ACPI: Unable to start ACPI Interpreter
This leaves the ACPI implementation in such a broken state that subsequent
kernel subsystem initialisations go wrong, resulting in among others
mismapped PCI memory, SATA and USB enumeration failures, and freezes.
As this is an older embedded platform that will likely never see any BIOS
updates to address this issue and its default shipping OS only complies to
ACPI 1.0, work around this by forcing `acpi=rsdt`. This patch, applied on
top of Linux 5.10.102, was confirmed on real hardware to fix the issue.
Signed-off-by: Mark Cilissen <mark@yotsuba.nl>
Cc: All applicable <stable@vger.kernel.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pablo Neira Ayuso [Thu, 17 Mar 2022 10:59:26 +0000 (11:59 +0100)]
netfilter: nf_tables: validate registers coming from userspace.
commit
6e1acfa387b9ff82cfc7db8cc3b6959221a95851 upstream.
Bail out in case userspace uses unsupported registers.
Fixes:
49499c3e6e18 ("netfilter: nf_tables: switch registers to 32 bit addressing")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pablo Neira Ayuso [Thu, 17 Mar 2022 11:04:42 +0000 (12:04 +0100)]
netfilter: nf_tables: initialize registers in nft_do_chain()
commit
4c905f6740a365464e91467aa50916555b28213d upstream.
Initialize registers to avoid stack leak into userspace.
Fixes:
96518518cc41 ("netfilter: add nftables")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephane Graber [Tue, 22 Mar 2022 22:42:06 +0000 (18:42 -0400)]
drivers: net: xgene: Fix regression in CRC stripping
commit
e9e6faeafaa00da1851bcf47912b0f1acae666b4 upstream.
All packets on ingress (except for jumbo) are terminated with a 4-bytes
CRC checksum. It's the responsability of the driver to strip those 4
bytes. Unfortunately a change dating back to March 2017 re-shuffled some
code and made the CRC stripping code effectively dead.
This change re-orders that part a bit such that the datalen is
immediately altered if needed.
Fixes:
4902a92270fb ("drivers: net: xgene: Add workaround for errata 10GE_8/ENET_11")
Cc: stable@vger.kernel.org
Signed-off-by: Stephane Graber <stgraber@ubuntu.com>
Tested-by: Stephane Graber <stgraber@ubuntu.com>
Link: https://lore.kernel.org/r/20220322224205.752795-1-stgraber@ubuntu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Giacomo Guiduzzi [Tue, 22 Mar 2022 20:06:54 +0000 (21:06 +0100)]
ALSA: pci: fix reading of swapped values from pcmreg in AC97 codec
commit
17aaf0193392cb3451bf0ac75ba396ec4cbded6e upstream.
Tests 72 and 78 for ALSA in kselftest fail due to reading
inconsistent values from some devices on a VirtualBox
Virtual Machine using the snd_intel8x0 driver for the AC'97
Audio Controller device.
Taking for example test number 72, this is what the test reports:
"Surround Playback Volume.0 expected 1 but read 0, is_volatile 0"
"Surround Playback Volume.1 expected 0 but read 1, is_volatile 0"
These errors repeat for each value from 0 to 31.
Taking a look at these error messages it is possible to notice
that the written values are read back swapped.
When the write is performed, these values are initially stored in
an array used to sanity-check them and write them in the pcmreg
array. To write them, the two one-byte values are packed together
in a two-byte variable through bitwise operations: the first
value is shifted left by one byte and the second value is stored in the
right byte through a bitwise OR. When reading the values back,
right shifts are performed to retrieve the previously stored
bytes. These shifts are executed in the wrong order, thus
reporting the values swapped as shown above.
This patch fixes this mistake by reversing the read
operations' order.
Signed-off-by: Giacomo Guiduzzi <guiduzzi.giacomo@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220322200653.15862-1-guiduzzi.giacomo@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan Teh [Sun, 13 Mar 2022 19:56:17 +0000 (19:56 +0000)]
ALSA: cmipci: Restore aux vol on suspend/resume
commit
c14231cc04337c2c2a937db084af342ce704dbde upstream.
Save and restore CM_REG_AUX_VOL instead of register 0x24 twice on
suspend/resume.
Tested on CMI8738LX.
Fixes:
cb60e5f5b2b1 ("[ALSA] cmipci - Add PM support")
Signed-off-by: Jonathan Teh <jonathan.teh@outlook.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/DBAPR04MB7366CB3EA9C8521C35C56E8B920E9@DBAPR04MB7366.eurprd04.prod.outlook.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lars-Peter Clausen [Fri, 11 Mar 2022 20:14:00 +0000 (21:14 +0100)]
ALSA: usb-audio: Add mute TLV for playback volumes on RODE NT-USB
commit
0f306cca42fe879694fb5e2382748c43dc9e0196 upstream.
For the RODE NT-USB the lowest Playback mixer volume setting mutes the
audio output. But it is not reported as such causing e.g. PulseAudio to
accidentally mute the device when selecting a low volume.
Fix this by applying the existing quirk for this kind of issue when the
device is detected.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220311201400.235892-1-lars@metafoo.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 22 Mar 2022 17:13:25 +0000 (18:13 +0100)]
ALSA: pcm: Add stream lock during PCM reset ioctl operations
commit
1f68915b2efd0d6bfd6e124aa63c94b3c69f127c upstream.
snd_pcm_reset() is a non-atomic operation, and it's allowed to run
during the PCM stream running. It implies that the manipulation of
hw_ptr and other parameters might be racy.
This patch adds the PCM stream lock at appropriate places in
snd_pcm_*_reset() actions for covering that.
Cc: <stable@vger.kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220322171325.4355-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 22 Mar 2022 17:07:20 +0000 (18:07 +0100)]
ALSA: pcm: Fix races among concurrent prealloc proc writes
commit
69534c48ba8ce552ce383b3dfdb271ffe51820c3 upstream.
We have no protection against concurrent PCM buffer preallocation
changes via proc files, and it may potentially lead to UAF or some
weird problem. This patch applies the PCM open_mutex to the proc
write operation for avoiding the racy proc writes and the PCM stream
open (and further operations).
Cc: <stable@vger.kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220322170720.3529-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 22 Mar 2022 17:07:19 +0000 (18:07 +0100)]
ALSA: pcm: Fix races among concurrent prepare and hw_params/hw_free calls
commit
3c3201f8c7bb77eb53b08a3ca8d9a4ddc500b4c0 upstream.
Like the previous fixes to hw_params and hw_free ioctl races, we need
to paper over the concurrent prepare ioctl calls against hw_params and
hw_free, too.
This patch implements the locking with the existing
runtime->buffer_mutex for prepare ioctls. Unlike the previous case
for snd_pcm_hw_hw_params() and snd_pcm_hw_free(), snd_pcm_prepare() is
performed to the linked streams, hence the lock can't be applied
simply on the top. For tracking the lock in each linked substream, we
modify snd_pcm_action_group() slightly and apply the buffer_mutex for
the case stream_lock=false (formerly there was no lock applied)
there.
Cc: <stable@vger.kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220322170720.3529-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 22 Mar 2022 17:07:18 +0000 (18:07 +0100)]
ALSA: pcm: Fix races among concurrent read/write and buffer changes
commit
dca947d4d26dbf925a64a6cfb2ddbc035e831a3d upstream.
In the current PCM design, the read/write syscalls (as well as the
equivalent ioctls) are allowed before the PCM stream is running, that
is, at PCM PREPARED state. Meanwhile, we also allow to re-issue
hw_params and hw_free ioctl calls at the PREPARED state that may
change or free the buffers, too. The problem is that there is no
protection against those mix-ups.
This patch applies the previously introduced runtime->buffer_mutex to
the read/write operations so that the concurrent hw_params or hw_free
call can no longer interfere during the operation. The mutex is
unlocked before scheduling, so we don't take it too long.
Cc: <stable@vger.kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220322170720.3529-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 22 Mar 2022 17:07:17 +0000 (18:07 +0100)]
ALSA: pcm: Fix races among concurrent hw_params and hw_free calls
commit
92ee3c60ec9fe64404dc035e7c41277d74aa26cb upstream.
Currently we have neither proper check nor protection against the
concurrent calls of PCM hw_params and hw_free ioctls, which may result
in a UAF. Since the existing PCM stream lock can't be used for
protecting the whole ioctl operations, we need a new mutex to protect
those racy calls.
This patch introduced a new mutex, runtime->buffer_mutex, and applies
it to both hw_params and hw_free ioctl code paths. Along with it, the
both functions are slightly modified (the mmap_count check is moved
into the state-check block) for code simplicity.
Reported-by: Hu Jiahui <kirin.say@gmail.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220322170720.3529-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jason Zheng [Sun, 13 Mar 2022 09:22:16 +0000 (04:22 -0500)]
ALSA: hda/realtek: Add quirk for ASUS GA402
commit
b7557267c233b55d8e8d7ba4c68cf944fe2ec02c upstream.
ASUS GA402 requires a workaround to manage the routing of its 4 speakers
like the other ASUS models. Add a corresponding quirk entry to fix it.
Signed-off-by: Jason Zheng <jasonzheng2004@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220313092216.29858-1-jasonzheng2004@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
huangwenhui [Fri, 11 Mar 2022 09:38:36 +0000 (17:38 +0800)]
ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc671
commit
882bd07f564f97fca6e42ce6ce627ce24ce1ef5a upstream.
On a HP 288 Pro G8, the front mic could not be detected.In order to
get it working, the pin configuration needs to be set correctly, and
the ALC671_FIXUP_HP_HEADSET_MIC2 fixup needs to be applied.
Signed-off-by: huangwenhui <huangwenhuia@uniontech.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220311093836.20754-1-huangwenhuia@uniontech.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tim Crawford [Mon, 7 Mar 2022 19:32:29 +0000 (12:32 -0700)]
ALSA: hda/realtek: Add quirk for Clevo NP50PNJ
commit
9cb727506704b5323998047789fc871e64a6aa14 upstream.
Fixes headset detection on Clevo NP50PNJ.
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220307193229.5141-1-tcrawford@system76.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tim Crawford [Fri, 4 Mar 2022 17:08:40 +0000 (10:08 -0700)]
ALSA: hda/realtek: Add quirk for Clevo NP70PNJ
commit
0c20fce13e6e111463e3a15ce3cf6713fe518388 upstream.
Fixes headset detection on Clevo NP70PNJ.
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220304170840.3351-1-tcrawford@system76.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reza Jahanbakhshi [Fri, 4 Mar 2022 21:23:02 +0000 (22:23 +0100)]
ALSA: usb-audio: add mapping for new Corsair Virtuoso SE
commit
cd94df1795418056a19ff4cb44eadfc18ac99a57 upstream.
New device id for Corsair Virtuoso SE RGB Wireless that currently is not
in the mixer_map. This entry in the mixer_map is necessary in order to
label its mixer appropriately and allow userspace to pick the correct
volume controls. For instance, my own Corsair Virtuoso SE RGB Wireless
headset has this new ID and consequently, the sidetone and volume are not
working correctly without this change.
> sudo lsusb -v | grep -i corsair
Bus 007 Device 011: ID 1b1c:0a40 Corsair CORSAIR VIRTUOSO SE Wireless Gam
idVendor 0x1b1c Corsair
iManufacturer 1 Corsair
iProduct 2 CORSAIR VIRTUOSO SE Wireless Gaming Headset
Signed-off-by: Reza Jahanbakhshi <reza.jahanbakhshi@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220304212303.195949-1-reza.jahanbakhshi@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Fri, 18 Mar 2022 08:20:36 +0000 (09:20 +0100)]
ALSA: oss: Fix PCM OSS buffer allocation overflow
commit
efb6402c3c4a7c26d97c92d70186424097b6e366 upstream.
We've got syzbot reports hitting INT_MAX overflow at vmalloc()
allocation that is called from snd_pcm_plug_alloc(). Although we
apply the restrictions to input parameters, it's based only on the
hw_params of the underlying PCM device. Since the PCM OSS layer
allocates a temporary buffer for the data conversion, the size may
become unexpectedly large when more channels or higher rates is given;
in the reported case, it went over INT_MAX, hence it hits WARN_ON().
This patch is an attempt to avoid such an overflow and an allocation
for too large buffers. First off, it adds the limit of 1MB as the
upper bound for period bytes. This must be large enough for all use
cases, and we really don't want to handle a larger temporary buffer
than this size. The size check is performed at two places, where the
original period bytes is calculated and where the plugin buffer size
is calculated.
In addition, the driver uses array_size() and array3_size() for
multiplications to catch overflows for the converted period size and
buffer bytes.
Reported-by: syzbot+72732c532ac1454eeee9@syzkaller.appspotmail.com
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/00000000000085b1b305da5a66f3@google.com
Link: https://lore.kernel.org/r/20220318082036.29699-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 15 Mar 2022 16:41:58 +0000 (17:41 +0100)]
ASoC: sti: Fix deadlock via snd_pcm_stop_xrun() call
commit
455c5653f50e10b4f460ef24e99f0044fbe3401c upstream.
This is essentially a revert of the commit
dc865fb9e7c2 ("ASoC: sti:
Use snd_pcm_stop_xrun() helper"), which converted the manual
snd_pcm_stop() calls with snd_pcm_stop_xrun().
The commit above introduced a deadlock as snd_pcm_stop_xrun() itself
takes the PCM stream lock while the caller already holds it. Since
the conversion was done only for consistency reason and the open-call
with snd_pcm_stop() to the XRUN state is a correct usage, let's revert
the commit back as the fix.
Fixes:
dc865fb9e7c2 ("ASoC: sti: Use snd_pcm_stop_xrun() helper")
Reported-by: Daniel Palmer <daniel@0x0f.com>
Cc: Arnaud POULIQUEN <arnaud.pouliquen@st.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220315091319.3351522-1-daniel@0x0f.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Link: https://lore.kernel.org/r/20220315164158.19804-1-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Wed, 23 Mar 2022 00:41:47 +0000 (17:41 -0700)]
llc: fix netdevice reference leaks in llc_ui_bind()
commit
764f4eb6846f5475f1244767d24d25dd86528a4a upstream.
Whenever llc_ui_bind() and/or llc_ui_autobind()
took a reference on a netdevice but subsequently fail,
they must properly release their reference
or risk the infamous message from unregister_netdevice()
at device dismantle.
unregister_netdevice: waiting for eth0 to become free. Usage count = 3
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: 赵子轩 <beraphin@gmail.com>
Reported-by: Stoyan Manolov <smanolov@suse.de>
Link: https://lore.kernel.org/r/20220323004147.1990845-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Helmut Grohne [Sat, 26 Feb 2022 15:22:56 +0000 (16:22 +0100)]
Bluetooth: btusb: Add another Realtek 8761BU
commit
6dfbe29f45fb0bde29213dbd754a79e8bfc6ecef upstream.
This device is sometimes wrapped with a label "EDUP".
T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=03 Dev#=107 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2550 ProdID=8761 Rev= 2.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=
00E04C239987
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Helmut Grohne <helmut@subdivi.de>
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1955351
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tadeusz Struk [Sun, 16 Jan 2022 01:26:26 +0000 (17:26 -0800)]
tpm: Fix error handling in async work
commit
2e8e4c8f6673247e22efc7985ce5497accd16f88 upstream.
When an invalid (non existing) handle is used in a TPM command,
that uses the resource manager interface (/dev/tpmrm0) the resource
manager tries to load it from its internal cache, but fails and
the tpm_dev_transmit returns an -EINVAL error to the caller.
The existing async handler doesn't handle these error cases
currently and the condition in the poll handler never returns
mask with EPOLLIN set.
The result is that the poll call blocks and the application gets stuck
until the user_read_timer wakes it up after 120 sec.
Change the tpm_dev_async_work function to handle error conditions
returned from tpm_dev_transmit they are also reflected in the poll mask
and a correct error code could passed back to the caller.
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: <linux-integrity@vger.kernel.org>
Cc: <stable@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Fixes:
9e1b74a63f77 ("tpm: add support for nonblocking operation")
Tested-by: Jarkko Sakkinen<jarkko@kernel.org>
Signed-off-by: Tadeusz Struk <tstruk@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Tadeusz Struk <tadeusz.struk@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tadeusz Struk [Thu, 10 Mar 2022 23:25:38 +0000 (15:25 -0800)]
net: ipv6: fix skb_over_panic in __ip6_append_data
commit
5e34af4142ffe68f01c8a9acae83300f8911e20c upstream.
Syzbot found a kernel bug in the ipv6 stack:
LINK: https://syzkaller.appspot.com/bug?id=205d6f11d72329ab8d62a610c44c5e7e25415580
The reproducer triggers it by sending a crafted message via sendmmsg()
call, which triggers skb_over_panic, and crashes the kernel:
skbuff: skb_over_panic: text:
ffffffff84647fb4 len:65575 put:65575
head:
ffff888109ff0000 data:
ffff888109ff0088 tail:0x100af end:0xfec0
dev:<NULL>
Update the check that prevents an invalid packet with MTU equal
to the fregment header size to eat up all the space for payload.
The reproducer can be found here:
LINK: https://syzkaller.appspot.com/text?tag=ReproC&x=1648c83fb00000
Reported-by: syzbot+e223cf47ec8ae183f2a0@syzkaller.appspotmail.com
Signed-off-by: Tadeusz Struk <tadeusz.struk@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20220310232538.1044947-1-tadeusz.struk@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jordy Zomer [Tue, 11 Jan 2022 16:44:51 +0000 (17:44 +0100)]
nfc: st21nfca: Fix potential buffer overflows in EVT_TRANSACTION
commit
4fbcc1a4cb20fe26ad0225679c536c80f1648221 upstream.
It appears that there are some buffer overflows in EVT_TRANSACTION.
This happens because the length parameters that are passed to memcpy
come directly from skb->data and are not guarded in any way.
Signed-off-by: Jordy Zomer <jordy@pwning.systems>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Denis Efremov <denis.e.efremov@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matt Flax [Sun, 27 Mar 2022 11:42:47 +0000 (22:42 +1100)]
audioinjector.net: stereo and zero, use dev_err_probe, report success
Use dev_err_probe to follow best practice, and leave a message in
the kernel log indicate the driver was started successfully.
Noralf Trønnes [Mon, 7 Mar 2022 16:05:49 +0000 (17:05 +0100)]
overlays: Add overlay for MIPI DBI displays
Add an overlay that can be used with all displays that have a
MIPI DBI compatible controller (pixels over SPI).
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Noralf Trønnes [Wed, 2 Mar 2022 17:17:44 +0000 (18:17 +0100)]
configs: Add MIPI DBI display driver
Enable DRM_PANEL_MIPI_DBI as a module.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Noralf Trønnes [Sun, 27 Feb 2022 12:47:13 +0000 (13:47 +0100)]
drm/tiny: Add MIPI DBI compatible SPI driver
commit 0e65e2e upstream.
Add a driver that will work with most MIPI DBI compatible SPI panels.
This avoids adding a driver for every new MIPI DBI compatible controller
that is to be used by Linux. The 'compatible' Device Tree property with
a '.bin' suffix will be used to load a firmware file that contains the
controller configuration.
Example (driver will load sainsmart18.bin):
display@0 {
compatible = "sainsmart18", "panel-mipi-dbi-spi";
...
};
v5:
- kconfig: s/DRM_KMS_CMA_HELPER/DRM_GEM_CMA_HELPER/ (Sam)
- kconfig: Add select VIDEOMODE_HELPERS (Sam)
- kconfig: Add wiki url in the description (Sam)
- Split out and use of_get_drm_panel_display_mode()(Sam)
- Only use the first compatible to look for a firmware file since the
binding mandates 2 compatibles.
- Make having a firmware file mandatory so we can print an error
message if it's missing to improve the user experience. It's very
unlikely that a controller doesn't need to be initialized and if
it doesn't, it's possible to have a firmware file containing only
a DCS NOP.
v4:
- Move driver to drm/tiny where the other drivers of its kind are located.
The driver module will not be shared with a future DPI driver after all.
v3:
- Move properties to DT (Maxime)
- The MIPI DPI spec has optional support for DPI where the controller is
configured over DBI. Rework the command functions so they can be moved
to drm_mipi_dbi and shared with a future panel-mipi-dpi-spi driver
v2:
- Drop model property and use compatible instead (Rob)
- Add wiki entry in MAINTAINERS
Acked-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220227124713.39766-6-noralf@tronnes.org
Noralf Trønnes [Sun, 27 Feb 2022 12:47:12 +0000 (13:47 +0100)]
drm/mipi-dbi: Add driver_private member to struct mipi_dbi_dev
commit 1e7e8e1 upstream.
devm_drm_dev_alloc() can't allocate structures that embed a structure
which then again embeds drm_device. Workaround this by adding a
driver_private pointer to struct mipi_dbi_dev which the driver can use for
its additional state.
v3:
- Add documentation
Acked-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220227124713.39766-5-noralf@tronnes.org
Noralf Trønnes [Sun, 27 Feb 2022 12:47:11 +0000 (13:47 +0100)]
drm/modes: Add of_get_drm_panel_display_mode()
commit 95ae342 upstream.
Add a function to get a drm_display_mode from a panel-timing
device tree subnode.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220227124713.39766-4-noralf@tronnes.org
Noralf Trønnes [Sun, 27 Feb 2022 12:47:09 +0000 (13:47 +0100)]
dt-bindings: display: add bindings for MIPI DBI compatible SPI panels
commit 2f3468b upstream.
Add binding for MIPI DBI compatible SPI panels.
v6:
- Fix indentation (Rob)
v5:
- Add sainsmart18 to compatible items (Rob)
- Expand write-only description (Sam)
v4:
- There should only be two compatible (Maxime)
- s/panel-dbi-spi/panel-mipi-dbi-spi/in compatible
v3:
- Move properties to Device Tree (Maxime)
- Use contains for compatible (Maxime)
- Add backlight property to example
- Flesh out description
v2:
- Fix path for panel-common.yaml
- Use unevaluatedProperties
- Drop properties which are in the allOf section
- Drop model property (Rob)
Acked-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220227124713.39766-2-noralf@tronnes.org
Naushir Patuck [Tue, 22 Mar 2022 15:16:40 +0000 (15:16 +0000)]
drivers: staging: bcm2835-isp: Clear LS table handle in the firmware
When all nodes have stopped streaming, ensure the firmware has released its
handle on the LS table dmabuf. This is done by passing a null handle in the
LS params.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Dom Cobley [Thu, 27 Jan 2022 15:32:04 +0000 (15:32 +0000)]
vc4/drm:plane: Make use of chroma siting parameter
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Dom Cobley [Wed, 26 Jan 2022 15:58:13 +0000 (15:58 +0000)]
drm: Add chroma siting properties
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Dom Cobley [Fri, 9 Apr 2021 14:00:40 +0000 (15:00 +0100)]
vc4/drm: Handle fractional coordinates using the phase field
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Dom Cobley [Mon, 14 Mar 2022 17:56:10 +0000 (17:56 +0000)]
vc4/drm: vc4_plane: Keep fractional source coords inside state
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Phil Elwell [Wed, 23 Mar 2022 14:44:49 +0000 (14:44 +0000)]
Revert "usb: xhci: expand the scope of XHCI_VLI_SS_BULK_OUT_BUG"
This reverts commit
40686d87f87a46b3abf48a8dcaee5e0a031deafb.
See: https://github.com/raspberrypi/linux/issues/4930
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Greg Kroah-Hartman [Wed, 23 Mar 2022 08:16:44 +0000 (09:16 +0100)]
Linux 5.15.31
Link: https://lore.kernel.org/r/20220321133220.559554263@linuxfoundation.org
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Ron Economos <re@w6rz.net>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Fox Chen <foxhlchen@gmail.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Filipe Manana [Tue, 18 Jan 2022 13:39:34 +0000 (13:39 +0000)]
btrfs: skip reserved bytes warning on unmount after log cleanup failure
commit
40cdc509877bacb438213b83c7541c5e24a1d9ec upstream.
After the recent changes made by commit
c2e39305299f01 ("btrfs: clear
extent buffer uptodate when we fail to write it") and its followup fix,
commit
651740a5024117 ("btrfs: check WRITE_ERR when trying to read an
extent buffer"), we can now end up not cleaning up space reservations of
log tree extent buffers after a transaction abort happens, as well as not
cleaning up still dirty extent buffers.
This happens because if writeback for a log tree extent buffer failed,
then we have cleared the bit EXTENT_BUFFER_UPTODATE from the extent buffer
and we have also set the bit EXTENT_BUFFER_WRITE_ERR on it. Later on,
when trying to free the log tree with free_log_tree(), which iterates
over the tree, we can end up getting an -EIO error when trying to read
a node or a leaf, since read_extent_buffer_pages() returns -EIO if an
extent buffer does not have EXTENT_BUFFER_UPTODATE set and has the
EXTENT_BUFFER_WRITE_ERR bit set. Getting that -EIO means that we return
immediately as we can not iterate over the entire tree.
In that case we never update the reserved space for an extent buffer in
the respective block group and space_info object.
When this happens we get the following traces when unmounting the fs:
[174957.284509] BTRFS: error (device dm-0) in cleanup_transaction:1913: errno=-5 IO failure
[174957.286497] BTRFS: error (device dm-0) in free_log_tree:3420: errno=-5 IO failure
[174957.399379] ------------[ cut here ]------------
[174957.402497] WARNING: CPU: 2 PID: 3206883 at fs/btrfs/block-group.c:127 btrfs_put_block_group+0x77/0xb0 [btrfs]
[174957.407523] Modules linked in: btrfs overlay dm_zero (...)
[174957.424917] CPU: 2 PID: 3206883 Comm: umount Tainted: G W 5.16.0-rc5-btrfs-next-109 #1
[174957.426689] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[174957.428716] RIP: 0010:btrfs_put_block_group+0x77/0xb0 [btrfs]
[174957.429717] Code: 21 48 8b bd (...)
[174957.432867] RSP: 0018:
ffffb70d41cffdd0 EFLAGS:
00010206
[174957.433632] RAX:
0000000000000001 RBX:
ffff8b09c3848000 RCX:
ffff8b0758edd1c8
[174957.434689] RDX:
0000000000000001 RSI:
ffffffffc0b467e7 RDI:
ffff8b0758edd000
[174957.436068] RBP:
ffff8b0758edd000 R08:
0000000000000000 R09:
0000000000000000
[174957.437114] R10:
0000000000000246 R11:
0000000000000000 R12:
ffff8b09c3848148
[174957.438140] R13:
ffff8b09c3848198 R14:
ffff8b0758edd188 R15:
dead000000000100
[174957.439317] FS:
00007f328fb82800(0000) GS:
ffff8b0a2d200000(0000) knlGS:
0000000000000000
[174957.440402] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[174957.441164] CR2:
00007fff13563e98 CR3:
0000000404f4e005 CR4:
0000000000370ee0
[174957.442117] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[174957.443076] DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
[174957.443948] Call Trace:
[174957.444264] <TASK>
[174957.444538] btrfs_free_block_groups+0x255/0x3c0 [btrfs]
[174957.445238] close_ctree+0x301/0x357 [btrfs]
[174957.445803] ? call_rcu+0x16c/0x290
[174957.446250] generic_shutdown_super+0x74/0x120
[174957.446832] kill_anon_super+0x14/0x30
[174957.447305] btrfs_kill_super+0x12/0x20 [btrfs]
[174957.447890] deactivate_locked_super+0x31/0xa0
[174957.448440] cleanup_mnt+0x147/0x1c0
[174957.448888] task_work_run+0x5c/0xa0
[174957.449336] exit_to_user_mode_prepare+0x1e5/0x1f0
[174957.449934] syscall_exit_to_user_mode+0x16/0x40
[174957.450512] do_syscall_64+0x48/0xc0
[174957.450980] entry_SYSCALL_64_after_hwframe+0x44/0xae
[174957.451605] RIP: 0033:0x7f328fdc4a97
[174957.452059] Code: 03 0c 00 f7 (...)
[174957.454320] RSP: 002b:
00007fff13564ec8 EFLAGS:
00000246 ORIG_RAX:
00000000000000a6
[174957.455262] RAX:
0000000000000000 RBX:
00007f328feea264 RCX:
00007f328fdc4a97
[174957.456131] RDX:
0000000000000000 RSI:
0000000000000000 RDI:
0000560b8ae51dd0
[174957.457118] RBP:
0000560b8ae51ba0 R08:
0000000000000000 R09:
00007fff13563c40
[174957.458005] R10:
00007f328fe49fc0 R11:
0000000000000246 R12:
0000000000000000
[174957.459113] R13:
0000560b8ae51dd0 R14:
0000560b8ae51cb0 R15:
0000000000000000
[174957.460193] </TASK>
[174957.460534] irq event stamp: 0
[174957.461003] hardirqs last enabled at (0): [<
0000000000000000>] 0x0
[174957.461947] hardirqs last disabled at (0): [<
ffffffffb0e94214>] copy_process+0x934/0x2040
[174957.463147] softirqs last enabled at (0): [<
ffffffffb0e94214>] copy_process+0x934/0x2040
[174957.465116] softirqs last disabled at (0): [<
0000000000000000>] 0x0
[174957.466323] ---[ end trace
bc7ee0c490bce3af ]---
[174957.467282] ------------[ cut here ]------------
[174957.468184] WARNING: CPU: 2 PID: 3206883 at fs/btrfs/block-group.c:3976 btrfs_free_block_groups+0x330/0x3c0 [btrfs]
[174957.470066] Modules linked in: btrfs overlay dm_zero (...)
[174957.483137] CPU: 2 PID: 3206883 Comm: umount Tainted: G W 5.16.0-rc5-btrfs-next-109 #1
[174957.484691] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[174957.486853] RIP: 0010:btrfs_free_block_groups+0x330/0x3c0 [btrfs]
[174957.488050] Code: 00 00 00 ad de (...)
[174957.491479] RSP: 0018:
ffffb70d41cffde0 EFLAGS:
00010206
[174957.492520] RAX:
ffff8b08d79310b0 RBX:
ffff8b09c3848000 RCX:
0000000000000000
[174957.493868] RDX:
0000000000000001 RSI:
fffff443055ee600 RDI:
ffffffffb1131846
[174957.495183] RBP:
ffff8b08d79310b0 R08:
0000000000000000 R09:
0000000000000000
[174957.496580] R10:
0000000000000001 R11:
0000000000000000 R12:
ffff8b08d7931000
[174957.498027] R13:
ffff8b09c38492b0 R14:
dead000000000122 R15:
dead000000000100
[174957.499438] FS:
00007f328fb82800(0000) GS:
ffff8b0a2d200000(0000) knlGS:
0000000000000000
[174957.500990] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[174957.502117] CR2:
00007fff13563e98 CR3:
0000000404f4e005 CR4:
0000000000370ee0
[174957.503513] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[174957.504864] DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
[174957.506167] Call Trace:
[174957.506654] <TASK>
[174957.507047] close_ctree+0x301/0x357 [btrfs]
[174957.507867] ? call_rcu+0x16c/0x290
[174957.508567] generic_shutdown_super+0x74/0x120
[174957.509447] kill_anon_super+0x14/0x30
[174957.510194] btrfs_kill_super+0x12/0x20 [btrfs]
[174957.511123] deactivate_locked_super+0x31/0xa0
[174957.511976] cleanup_mnt+0x147/0x1c0
[174957.512610] task_work_run+0x5c/0xa0
[174957.513309] exit_to_user_mode_prepare+0x1e5/0x1f0
[174957.514231] syscall_exit_to_user_mode+0x16/0x40
[174957.515069] do_syscall_64+0x48/0xc0
[174957.515718] entry_SYSCALL_64_after_hwframe+0x44/0xae
[174957.516688] RIP: 0033:0x7f328fdc4a97
[174957.517413] Code: 03 0c 00 f7 d8 (...)
[174957.521052] RSP: 002b:
00007fff13564ec8 EFLAGS:
00000246 ORIG_RAX:
00000000000000a6
[174957.522514] RAX:
0000000000000000 RBX:
00007f328feea264 RCX:
00007f328fdc4a97
[174957.523950] RDX:
0000000000000000 RSI:
0000000000000000 RDI:
0000560b8ae51dd0
[174957.525375] RBP:
0000560b8ae51ba0 R08:
0000000000000000 R09:
00007fff13563c40
[174957.526763] R10:
00007f328fe49fc0 R11:
0000000000000246 R12:
0000000000000000
[174957.528058] R13:
0000560b8ae51dd0 R14:
0000560b8ae51cb0 R15:
0000000000000000
[174957.529404] </TASK>
[174957.529843] irq event stamp: 0
[174957.530256] hardirqs last enabled at (0): [<
0000000000000000>] 0x0
[174957.531061] hardirqs last disabled at (0): [<
ffffffffb0e94214>] copy_process+0x934/0x2040
[174957.532075] softirqs last enabled at (0): [<
ffffffffb0e94214>] copy_process+0x934/0x2040
[174957.533083] softirqs last disabled at (0): [<
0000000000000000>] 0x0
[174957.533865] ---[ end trace
bc7ee0c490bce3b0 ]---
[174957.534452] BTRFS info (device dm-0): space_info 4 has
1070841856 free, is not full
[174957.535404] BTRFS info (device dm-0): space_info total=
1073741824, used=2785280, pinned=0, reserved=49152, may_use=0, readonly=65536 zone_unusable=0
[174957.537029] BTRFS info (device dm-0): global_block_rsv: size 0 reserved 0
[174957.537859] BTRFS info (device dm-0): trans_block_rsv: size 0 reserved 0
[174957.538697] BTRFS info (device dm-0): chunk_block_rsv: size 0 reserved 0
[174957.539552] BTRFS info (device dm-0): delayed_block_rsv: size 0 reserved 0
[174957.540403] BTRFS info (device dm-0): delayed_refs_rsv: size 0 reserved 0
This also means that in case we have log tree extent buffers that are
still dirty, we can end up not cleaning them up in case we find an
extent buffer with EXTENT_BUFFER_WRITE_ERR set on it, as in that case
we have no way for iterating over the rest of the tree.
This issue is very often triggered with test cases generic/475 and
generic/648 from fstests.
The issue could almost be fixed by iterating over the io tree attached to
each log root which keeps tracks of the range of allocated extent buffers,
log_root->dirty_log_pages, however that does not work and has some
inconveniences:
1) After we sync the log, we clear the range of the extent buffers from
the io tree, so we can't find them after writeback. We could keep the
ranges in the io tree, with a separate bit to signal they represent
extent buffers already written, but that means we need to hold into
more memory until the transaction commits.
How much more memory is used depends a lot on whether we are able to
allocate contiguous extent buffers on disk (and how often) for a log
tree - if we are able to, then a single extent state record can
represent multiple extent buffers, otherwise we need multiple extent
state record structures to track each extent buffer.
In fact, my earlier approach did that:
https://lore.kernel.org/linux-btrfs/
3aae7c6728257c7ce2279d6660ee2797e5e34bbd.
1641300250.git.fdmanana@suse.com/
However that can cause a very significant negative impact on
performance, not only due to the extra memory usage but also because
we get a larger and deeper dirty_log_pages io tree.
We got a report that, on beefy machines at least, we can get such
performance drop with fsmark for example:
https://lore.kernel.org/linux-btrfs/
20220117082426.GE32491@xsang-OptiPlex-9020/
2) We would be doing it only to deal with an unexpected and exceptional
case, which is basically failure to read an extent buffer from disk
due to IO failures. On a healthy system we don't expect transaction
aborts to happen after all;
3) Instead of relying on iterating the log tree or tracking the ranges
of extent buffers in the dirty_log_pages io tree, using the radix
tree that tracks extent buffers (fs_info->buffer_radix) to find all
log tree extent buffers is not reliable either, because after writeback
of an extent buffer it can be evicted from memory by the release page
callback of the btree inode (btree_releasepage()).
Since there's no way to be able to properly cleanup a log tree without
being able to read its extent buffers from disk and without using more
memory to track the logical ranges of the allocated extent buffers do
the following:
1) When we fail to cleanup a log tree, setup a flag that indicates that
failure;
2) Trigger writeback of all log tree extent buffers that are still dirty,
and wait for the writeback to complete. This is just to cleanup their
state, page states, page leaks, etc;
3) When unmounting the fs, ignore if the number of bytes reserved in a
block group and in a space_info is not 0 if, and only if, we failed to
cleanup a log tree. Also ignore only for metadata block groups and the
metadata space_info object.
This is far from a perfect solution, but it serves to silence test
failures such as those from generic/475 and generic/648. However having
a non-zero value for the reserved bytes counters on unmount after a
transaction abort, is not such a terrible thing and it's completely
harmless, it does not affect the filesystem integrity in any way.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Petlan [Thu, 17 Mar 2022 13:55:36 +0000 (14:55 +0100)]
perf symbols: Fix symbol size calculation condition
commit
3cf6a32f3f2a45944dd5be5c6ac4deb46bcd3bee upstream.
Before this patch, the symbol end address fixup to be called, needed two
conditions being met:
if (prev->end == prev->start && prev->end != curr->start)
Where
"prev->end == prev->start" means that prev is zero-long
(and thus needs a fixup)
and
"prev->end != curr->start" means that fixup hasn't been applied yet
However, this logic is incorrect in the following situation:
*curr = {rb_node = {__rb_parent_color =
278218928,
rb_right = 0x0, rb_left = 0x0},
start = 0xc000000000062354,
end = 0xc000000000062354, namelen = 40, type = 2 '\002',
binding = 0 '\000', idle = 0 '\000', ignore = 0 '\000',
inlined = 0 '\000', arch_sym = 0 '\000', annotate2 = false,
name = 0x1159739e "kprobe_optinsn_page\t[__builtin__kprobes]"}
*prev = {rb_node = {__rb_parent_color =
278219041,
rb_right = 0x109548b0, rb_left = 0x109547c0},
start = 0xc000000000062354,
end = 0xc000000000062354, namelen = 12, type = 2 '\002',
binding = 1 '\001', idle = 0 '\000', ignore = 0 '\000',
inlined = 0 '\000', arch_sym = 0 '\000', annotate2 = false,
name = 0x1095486e "optinsn_slot"}
In this case, prev->start == prev->end == curr->start == curr->end,
thus the condition above thinks that "we need a fixup due to zero
length of prev symbol, but it has been probably done, since the
prev->end == curr->start", which is wrong.
After the patch, the execution path proceeds to arch__symbols__fixup_end
function which fixes up the size of prev symbol by adding page_size to
its end offset.
Fixes:
3b01a413c196c910 ("perf symbols: Improve kallsyms symbol end addr calculation")
Signed-off-by: Michael Petlan <mpetlan@redhat.com>
Cc: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: http://lore.kernel.org/lkml/20220317135536.805-1-mpetlan@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pavel Skripkin [Mon, 14 Mar 2022 05:56:32 +0000 (22:56 -0700)]
Input: aiptek - properly check endpoint type
commit
5600f6986628dde8881734090588474f54a540a8 upstream.
Syzbot reported warning in usb_submit_urb() which is caused by wrong
endpoint type. There was a check for the number of endpoints, but not
for the type of endpoint.
Fix it by replacing old desc.bNumEndpoints check with
usb_find_common_endpoints() helper for finding endpoints
Fail log:
usb 5-1: BOGUS urb xfer, pipe 1 != type 3
WARNING: CPU: 2 PID: 48 at drivers/usb/core/urb.c:502 usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
Modules linked in:
CPU: 2 PID: 48 Comm: kworker/2:2 Not tainted 5.17.0-rc6-syzkaller-00226-g07ebd38a0da2 #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
Workqueue: usb_hub_wq hub_event
...
Call Trace:
<TASK>
aiptek_open+0xd5/0x130 drivers/input/tablet/aiptek.c:830
input_open_device+0x1bb/0x320 drivers/input/input.c:629
kbd_connect+0xfe/0x160 drivers/tty/vt/keyboard.c:1593
Fixes:
8e20cf2bce12 ("Input: aiptek - fix crash on detecting device without endpoints")
Reported-and-tested-by: syzbot+75cccf2b7da87fb6f84b@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20220308194328.26220-1-paskripkin@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matt Lupfer [Tue, 8 Mar 2022 15:27:02 +0000 (15:27 +0000)]
scsi: mpt3sas: Page fault in reply q processing
commit
69ad4ef868c1fc7609daa235dfa46d28ba7a3ba3 upstream.
A page fault was encountered in mpt3sas on a LUN reset error path:
[ 145.763216] mpt3sas_cm1: Task abort tm failed: handle(0x0002),timeout(30) tr_method(0x0) smid(3) msix_index(0)
[ 145.778932] scsi 1:0:0:0: task abort: FAILED scmd(0x0000000024ba29a2)
[ 145.817307] scsi 1:0:0:0: attempting device reset! scmd(0x0000000024ba29a2)
[ 145.827253] scsi 1:0:0:0: [sg1] tag#2 CDB: Receive Diagnostic 1c 01 01 ff fc 00
[ 145.837617] scsi target1:0:0: handle(0x0002), sas_address(0x500605b0000272b9), phy(0)
[ 145.848598] scsi target1:0:0: enclosure logical id(0x500605b0000272b8), slot(0)
[ 149.858378] mpt3sas_cm1: Poll ReplyDescriptor queues for completion of smid(0), task_type(0x05), handle(0x0002)
[ 149.875202] BUG: unable to handle page fault for address:
00000007fffc445d
[ 149.885617] #PF: supervisor read access in kernel mode
[ 149.894346] #PF: error_code(0x0000) - not-present page
[ 149.903123] PGD 0 P4D 0
[ 149.909387] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 149.917417] CPU: 24 PID: 3512 Comm: scsi_eh_1 Kdump: loaded Tainted: G S O 5.10.89-altav-1 #1
[ 149.934327] Hardware name: DDN 200NVX2 /200NVX2-MB , BIOS ATHG2.2.02.01 09/10/2021
[ 149.951871] RIP: 0010:_base_process_reply_queue+0x4b/0x900 [mpt3sas]
[ 149.961889] Code: 0f 84 22 02 00 00 8d 48 01 49 89 fd 48 8d 57 38 f0 0f b1 4f 38 0f 85 d8 01 00 00 49 8b 45 10 45 31 e4 41 8b 55 0c 48 8d 1c d0 <0f> b6 03 83 e0 0f 3c 0f 0f 85 a2 00 00 00 e9 e6 01 00 00 0f b7 ee
[ 149.991952] RSP: 0018:
ffffc9000f1ebcb8 EFLAGS:
00010246
[ 150.000937] RAX:
0000000000000055 RBX:
00000007fffc445d RCX:
000000002548f071
[ 150.011841] RDX:
00000000ffff8881 RSI:
0000000000000001 RDI:
ffff888125ed50d8
[ 150.022670] RBP:
0000000000000000 R08:
0000000000000000 R09:
c0000000ffff7fff
[ 150.033445] R10:
ffffc9000f1ebb68 R11:
ffffc9000f1ebb60 R12:
0000000000000000
[ 150.044204] R13:
ffff888125ed50d8 R14:
0000000000000080 R15:
34cdc00034cdea80
[ 150.054963] FS:
0000000000000000(0000) GS:
ffff88dfaf200000(0000) knlGS:
0000000000000000
[ 150.066715] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 150.076078] CR2:
00000007fffc445d CR3:
000000012448a006 CR4:
0000000000770ee0
[ 150.086887] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[ 150.097670] DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
[ 150.108323] PKRU:
55555554
[ 150.114690] Call Trace:
[ 150.120497] ? printk+0x48/0x4a
[ 150.127049] mpt3sas_scsih_issue_tm.cold.114+0x2e/0x2b3 [mpt3sas]
[ 150.136453] mpt3sas_scsih_issue_locked_tm+0x86/0xb0 [mpt3sas]
[ 150.145759] scsih_dev_reset+0xea/0x300 [mpt3sas]
[ 150.153891] scsi_eh_ready_devs+0x541/0x9e0 [scsi_mod]
[ 150.162206] ? __scsi_host_match+0x20/0x20 [scsi_mod]
[ 150.170406] ? scsi_try_target_reset+0x90/0x90 [scsi_mod]
[ 150.178925] ? blk_mq_tagset_busy_iter+0x45/0x60
[ 150.186638] ? scsi_try_target_reset+0x90/0x90 [scsi_mod]
[ 150.195087] scsi_error_handler+0x3a5/0x4a0 [scsi_mod]
[ 150.203206] ? __schedule+0x1e9/0x610
[ 150.209783] ? scsi_eh_get_sense+0x210/0x210 [scsi_mod]
[ 150.217924] kthread+0x12e/0x150
[ 150.224041] ? kthread_worker_fn+0x130/0x130
[ 150.231206] ret_from_fork+0x1f/0x30
This is caused by mpt3sas_base_sync_reply_irqs() using an invalid reply_q
pointer outside of the list_for_each_entry() loop. At the end of the full
list traversal the pointer is invalid.
Move the _base_process_reply_queue() call inside of the loop.
Link: https://lore.kernel.org/r/d625deae-a958-0ace-2ba3-0888dd0a415b@ddn.com
Fixes:
711a923c14d9 ("scsi: mpt3sas: Postprocessing of target and LUN reset")
Cc: stable@vger.kernel.org
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Matt Lupfer <mlupfer@ddn.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Thu, 3 Mar 2022 21:00:17 +0000 (16:00 -0500)]
usb: usbtmc: Fix bug in pipe direction for control transfers
commit
e9b667a82cdcfe21d590344447d65daed52b353b upstream.
The syzbot fuzzer reported a minor bug in the usbtmc driver:
usb 5-1: BOGUS control dir, pipe
80001e80 doesn't match bRequestType 0
WARNING: CPU: 0 PID: 3813 at drivers/usb/core/urb.c:412
usb_submit_urb+0x13a5/0x1970 drivers/usb/core/urb.c:410
Modules linked in:
CPU: 0 PID: 3813 Comm: syz-executor122 Not tainted
5.17.0-rc5-syzkaller-00306-g2293be58d6a1 #0
...
Call Trace:
<TASK>
usb_start_wait_urb+0x113/0x530 drivers/usb/core/message.c:58
usb_internal_control_msg drivers/usb/core/message.c:102 [inline]
usb_control_msg+0x2a5/0x4b0 drivers/usb/core/message.c:153
usbtmc_ioctl_request drivers/usb/class/usbtmc.c:1947 [inline]
The problem is that usbtmc_ioctl_request() uses usb_rcvctrlpipe() for
all of its transfers, whether they are in or out. It's easy to fix.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+a48e3d1a875240cab5de@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YiEsYTPEE6lOCOA5@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Sun, 6 Mar 2022 02:47:22 +0000 (21:47 -0500)]
usb: gadget: Fix use-after-free bug by not setting udc->dev.driver
commit
16b1941eac2bd499f065a6739a40ce0011a3d740 upstream.
The syzbot fuzzer found a use-after-free bug:
BUG: KASAN: use-after-free in dev_uevent+0x712/0x780 drivers/base/core.c:2320
Read of size 8 at addr
ffff88802b934098 by task udevd/3689
CPU: 2 PID: 3689 Comm: udevd Not tainted 5.17.0-rc4-syzkaller-00229-g4f12b742eb2b #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description.constprop.0.cold+0x8d/0x303 mm/kasan/report.c:255
__kasan_report mm/kasan/report.c:442 [inline]
kasan_report.cold+0x83/0xdf mm/kasan/report.c:459
dev_uevent+0x712/0x780 drivers/base/core.c:2320
uevent_show+0x1b8/0x380 drivers/base/core.c:2391
dev_attr_show+0x4b/0x90 drivers/base/core.c:2094
Although the bug manifested in the driver core, the real cause was a
race with the gadget core. dev_uevent() does:
if (dev->driver)
add_uevent_var(env, "DRIVER=%s", dev->driver->name);
and between the test and the dereference of dev->driver, the gadget
core sets dev->driver to NULL.
The race wouldn't occur if the gadget core registered its devices on
a real bus, using the standard synchronization techniques of the
driver core. However, it's not necessary to make such a large change
in order to fix this bug; all we need to do is make sure that
udc->dev.driver is always NULL.
In fact, there is no reason for udc->dev.driver ever to be set to
anything, let alone to the value it currently gets: the address of the
gadget's driver. After all, a gadget driver only knows how to manage
a gadget, not how to manage a UDC.
This patch simply removes the statements in the gadget core that touch
udc->dev.driver.
Fixes:
2ccea03a8f7e ("usb: gadget: introduce UDC Class")
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+348b571beb5eeb70a582@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YiQgukfFFbBnwJ/9@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Tue, 1 Mar 2022 08:04:24 +0000 (11:04 +0300)]
usb: gadget: rndis: prevent integer overflow in rndis_set_response()
commit
65f3324f4b6fed78b8761c3b74615ecf0ffa81fa upstream.
If "BufOffset" is very large the "BufOffset + 8" operation can have an
integer overflow.
Cc: stable@kernel.org
Fixes:
38ea1eac7d88 ("usb: gadget: rndis: check size of RNDIS_MSG_SET command")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220301080424.GA17208@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann [Wed, 16 Mar 2022 18:38:18 +0000 (19:38 +0100)]
arm64: fix clang warning about TRAMP_VALIAS
[ Upstream commit
7f34b43e07cb512b28543fdcb9f35d1fbfda9ebc ]
The newly introduced TRAMP_VALIAS definition causes a build warning
with clang-14:
arch/arm64/include/asm/vectors.h:66:31: error: arithmetic on a null pointer treated as a cast from integer to pointer is a GNU extension [-Werror,-Wnull-pointer-arithmetic]
return (char *)TRAMP_VALIAS + SZ_2K * slot;
Change the addition to something clang does not complain about.
Fixes:
bd09128d16fa ("arm64: Add percpu vectors for EL1")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Morse <james.morse@arm.com>
Link: https://lore.kernel.org/r/20220316183833.1563139-1-arnd@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ivan Vecera [Thu, 17 Mar 2022 10:45:24 +0000 (11:45 +0100)]
iavf: Fix hang during reboot/shutdown
[ Upstream commit
b04683ff8f0823b869c219c78ba0d974bddea0b5 ]
Recent commit
974578017fc1 ("iavf: Add waiting so the port is
initialized in remove") adds a wait-loop at the beginning of
iavf_remove() to ensure that port initialization is finished
prior unregistering net device. This causes a regression
in reboot/shutdown scenario because in this case callback
iavf_shutdown() is called and this callback detaches the device,
makes it down if it is running and sets its state to __IAVF_REMOVE.
Later shutdown callback of associated PF driver (e.g. ice_shutdown)
is called. That callback calls among other things sriov_disable()
that calls indirectly iavf_remove() (see stack trace below).
As the adapter state is already __IAVF_REMOVE then the mentioned
loop is end-less and shutdown process hangs.
The patch fixes this by checking adapter's state at the beginning
of iavf_remove() and skips the rest of the function if the adapter
is already in remove state (shutdown is in progress).
Reproducer:
1. Create VF on PF driven by ice or i40e driver
2. Ensure that the VF is bound to iavf driver
3. Reboot
[52625.981294] sysrq: SysRq : Show Blocked State
[52625.988377] task:reboot state:D stack: 0 pid:17359 ppid: 1 f2
[52625.996732] Call Trace:
[52625.999187] __schedule+0x2d1/0x830
[52626.007400] schedule+0x35/0xa0
[52626.010545] schedule_hrtimeout_range_clock+0x83/0x100
[52626.020046] usleep_range+0x5b/0x80
[52626.023540] iavf_remove+0x63/0x5b0 [iavf]
[52626.027645] pci_device_remove+0x3b/0xc0
[52626.031572] device_release_driver_internal+0x103/0x1f0
[52626.036805] pci_stop_bus_device+0x72/0xa0
[52626.040904] pci_stop_and_remove_bus_device+0xe/0x20
[52626.045870] pci_iov_remove_virtfn+0xba/0x120
[52626.050232] sriov_disable+0x2f/0xe0
[52626.053813] ice_free_vfs+0x7c/0x340 [ice]
[52626.057946] ice_remove+0x220/0x240 [ice]
[52626.061967] ice_shutdown+0x16/0x50 [ice]
[52626.065987] pci_device_shutdown+0x34/0x60
[52626.070086] device_shutdown+0x165/0x1c5
[52626.074011] kernel_restart+0xe/0x30
[52626.077593] __do_sys_reboot+0x1d2/0x210
[52626.093815] do_syscall_64+0x5b/0x1a0
[52626.097483] entry_SYSCALL_64_after_hwframe+0x65/0xca
Fixes:
974578017fc1 ("iavf: Add waiting so the port is initialized in remove")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://lore.kernel.org/r/20220317104524.2802848-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vladimir Oltean [Wed, 16 Mar 2022 19:21:17 +0000 (21:21 +0200)]
net: mscc: ocelot: fix backwards compatibility with single-chain tc-flower offload
[ Upstream commit
8e0341aefcc9133f3f48683873284b169581315b ]
ACL rules can be offloaded to VCAP IS2 either through chain 0, or, since
the blamed commit, through a chain index whose number encodes a specific
PAG (Policy Action Group) and lookup number.
The chain number is translated through ocelot_chain_to_pag() into a PAG,
and through ocelot_chain_to_lookup() into a lookup number.
The problem with the blamed commit is that the above 2 functions don't
have special treatment for chain 0. So ocelot_chain_to_pag(0) returns
filter->pag = 224, which is in fact -32, but the "pag" field is an u8.
So we end up programming the hardware with VCAP IS2 entries having a PAG
of 224. But the way in which the PAG works is that it defines a subset
of VCAP IS2 filters which should match on a packet. The default PAG is
0, and previous VCAP IS1 rules (which we offload using 'goto') can
modify it. So basically, we are installing filters with a PAG on which
no packet will ever match. This is the hardware equivalent of adding
filters to a chain which has no 'goto' to it.
Restore the previous functionality by making ACL filters offloaded to
chain 0 go to PAG 0 and lookup number 0. The choice of PAG is clearly
correct, but the choice of lookup number isn't "as before" (which was to
leave the lookup a "don't care"). However, lookup 0 should be fine,
since even though there are ACL actions (policers) which have a
requirement to be used in a specific lookup, that lookup is 0.
Fixes:
226e9cd82a96 ("net: mscc: ocelot: only install TCAM entries into a specific lookup and PAG")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220316192117.2568261-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Doug Berger [Thu, 17 Mar 2022 01:28:12 +0000 (18:28 -0700)]
net: bcmgenet: skip invalid partial checksums
[ Upstream commit
0f643c88c8d240eba0ea25c2e095a46515ff46e9 ]
The RXCHK block will return a partial checksum of 0 if it encounters
a problem while receiving a packet. Since a 1's complement sum can
only produce this result if no bits are set in the received data
stream it is fair to treat it as an invalid partial checksum and
not pass it up the stack.
Fixes:
810155397890 ("net: bcmgenet: use CHECKSUM_COMPLETE for NETIF_F_RXCSUM")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220317012812.1313196-1-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Manish Chopra [Wed, 16 Mar 2022 21:46:13 +0000 (14:46 -0700)]
bnx2x: fix built-in kernel driver load failure
[ Upstream commit
424e7834e293936a54fcf05173f2884171adc5a3 ]
Commit
b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
added request_firmware() logic in probe() which caused
load failure when firmware file is not present in initrd (below),
as access to firmware file is not feasible during probe.
Direct firmware load for bnx2x/bnx2x-e2-7.13.15.0.fw failed with error -2
Direct firmware load for bnx2x/bnx2x-e2-7.13.21.0.fw failed with error -2
This patch fixes this issue by -
1. Removing request_firmware() logic from the probe()
such that .ndo_open() handle it as it used to handle
it earlier
2. Given request_firmware() is removed from probe(), so
driver has to relax FW version comparisons a bit against
the already loaded FW version (by some other PFs of same
adapter) to allow different compatible/close enough FWs with which
multiple PFs may run with (in different environments), as the
given PF who is in probe flow has no idea now with which firmware
file version it is going to initialize the device in ndo_open()
Link: https://lore.kernel.org/all/46f2d9d9-ae7f-b332-ddeb-b59802be2bab@molgen.mpg.de/
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Fixes:
b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220316214613.6884-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Juerg Haefliger [Wed, 16 Mar 2022 15:18:35 +0000 (16:18 +0100)]
net: phy: mscc: Add MODULE_FIRMWARE macros
[ Upstream commit
f1858c277ba40172005b76a31e6bb931bfc19d9c ]
The driver requires firmware so define MODULE_FIRMWARE so that modinfo
provides the details.
Fixes:
fa164e40c53b ("net: phy: mscc: split the driver into separate files")
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Link: https://lore.kernel.org/r/20220316151835.88765-1-juergh@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Miaoqian Lin [Wed, 16 Mar 2022 08:26:02 +0000 (08:26 +0000)]
net: dsa: Add missing of_node_put() in dsa_port_parse_of
[ Upstream commit
cb0b430b4e3acc88c85e0ad2e25f2a25a5765262 ]
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
Fixes:
6d4e5c570c2d ("net: dsa: get port type at parse time")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220316082602.10785-1-linmq006@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Thomas Zimmermann [Tue, 15 Mar 2022 08:45:59 +0000 (09:45 +0100)]
drm: Don't make DRM_PANEL_BRIDGE dependent on DRM_KMS_HELPERS
[ Upstream commit
3c3384050d68570f9de0fec9e58824decfefba7a ]
Fix a number of undefined references to drm_kms_helper.ko in
drm_dp_helper.ko:
arm-suse-linux-gnueabi-ld: drivers/gpu/drm/dp/drm_dp_mst_topology.o: in function `drm_dp_mst_duplicate_state':
drm_dp_mst_topology.c:(.text+0x2df0): undefined reference to `__drm_atomic_helper_private_obj_duplicate_state'
arm-suse-linux-gnueabi-ld: drivers/gpu/drm/dp/drm_dp_mst_topology.o: in function `drm_dp_delayed_destroy_work':
drm_dp_mst_topology.c:(.text+0x370c): undefined reference to `drm_kms_helper_hotplug_event'
arm-suse-linux-gnueabi-ld: drivers/gpu/drm/dp/drm_dp_mst_topology.o: in function `drm_dp_mst_up_req_work':
drm_dp_mst_topology.c:(.text+0x7938): undefined reference to `drm_kms_helper_hotplug_event'
arm-suse-linux-gnueabi-ld: drivers/gpu/drm/dp/drm_dp_mst_topology.o: in function `drm_dp_mst_link_probe_work':
drm_dp_mst_topology.c:(.text+0x82e0): undefined reference to `drm_kms_helper_hotplug_event'
This happens if panel-edp.ko has been configured with
DRM_PANEL_EDP=y
DRM_DP_HELPER=y
DRM_KMS_HELPER=m
which builds DP helpers into the kernel and KMS helpers sa a module.
Making DRM_PANEL_EDP select DRM_KMS_HELPER resolves this problem.
To avoid a resulting cyclic dependency with DRM_PANEL_BRIDGE, don't
make the latter depend on DRM_KMS_HELPER and fix the one DRM bridge
drivers that doesn't already select DRM_KMS_HELPER. As KMS helpers
cannot be selected directly by the user, config symbols should avoid
depending on it anyway.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes:
3755d35ee1d2 ("drm/panel: Select DRM_DP_HELPER for DRM_PANEL_EDP")
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Brian Masney <bmasney@redhat.com>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Linux Kernel Functional Testing <lkft@linaro.org>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: dri-devel@lists.freedesktop.org
Cc: Dave Airlie <airlied@redhat.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/478296/
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nicolas Dichtel [Tue, 15 Mar 2022 09:20:08 +0000 (10:20 +0100)]
net: handle ARPHRD_PIMREG in dev_is_mac_header_xmit()
[ Upstream commit
4ee06de7729d795773145692e246a06448b1eb7a ]
This kind of interface doesn't have a mac header. This patch fixes
bpf_redirect() to a PIM interface.
Fixes:
27b29f63058d ("bpf: add bpf_redirect() helper")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20220315092008.31423-1-nicolas.dichtel@6wind.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Marek Vasut [Sun, 20 Feb 2022 04:07:18 +0000 (05:07 +0100)]
drm/panel: simple: Fix Innolux G070Y2-L01 BPP settings
[ Upstream commit
fc1b6ef7bfb3d1d4df868b1c3e0480cacda6cd81 ]
The Innolux G070Y2-L01 supports two modes of operation:
1) FRC=Low/NC ... MEDIA_BUS_FMT_RGB666_1X7X3_SPWG ... BPP=6
2) FRC=High ..... MEDIA_BUS_FMT_RGB888_1X7X4_SPWG ... BPP=8
Currently the panel description mixes both, BPP from 1) and bus
format from 2), which triggers a warning at panel-simple.c:615.
Pick the later, set bpp=8, fix the warning.
Fixes:
a5d2ade627dca ("drm/panel: simple: Add support for Innolux G070Y2-L01")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Fritz <chf.fritz@googlemail.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220220040718.532866-1-marex@denx.de
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Christoph Niedermaier [Tue, 1 Feb 2022 11:36:43 +0000 (12:36 +0100)]
drm/imx: parallel-display: Remove bus flags check in imx_pd_bridge_atomic_check()
[ Upstream commit
6061806a863e8b65b109eb06a280041cc7525442 ]
If display timings were read from the devicetree using
of_get_display_timing() and pixelclk-active is defined
there, the flag DISPLAY_FLAGS_SYNC_POSEDGE/NEGEDGE is
automatically generated. Through the function
drm_bus_flags_from_videomode() e.g. called in the
panel-simple driver this flag got into the bus flags,
but then in imx_pd_bridge_atomic_check() the bus flag
check failed and will not initialize the display. The
original commit
fe141cedc433 does not explain why this
check was introduced. So remove the bus flags check,
because it stops the initialization of the display with
valid bus flags.
Fixes:
fe141cedc433 ("drm/imx: pd: Use bus format/flags provided by the bridge when available")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: linux-arm-kernel@lists.infradead.org
To: dri-devel@lists.freedesktop.org
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220201113643.4638-1-cniedermaier@dh-electronics.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jiasheng Jiang [Mon, 14 Mar 2022 02:01:25 +0000 (10:01 +0800)]
hv_netvsc: Add check for kvmalloc_array
[ Upstream commit
886e44c9298a6b428ae046e2fa092ca52e822e6a ]
As the potential failure of the kvmalloc_array(),
it should be better to check and restore the 'data'
if fails in order to avoid the dereference of the
NULL pointer.
Fixes:
6ae746711263 ("hv_netvsc: Add per-cpu ethtool stats for netvsc")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220314020125.2365084-1-jiasheng@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Przemyslaw Patynowski [Wed, 9 Mar 2022 15:37:39 +0000 (16:37 +0100)]
iavf: Fix double free in iavf_reset_task
[ Upstream commit
16b2dd8cdf6f4e0597c34899de74b4d012b78188 ]
Fix double free possibility in iavf_disable_vf, as crit_lock is
freed in caller, iavf_reset_task. Add kernel-doc for iavf_disable_vf.
Remove mutex_unlock in iavf_disable_vf.
Without this patch there is double free scenario, when calling
iavf_reset_task.
Fixes:
e85ff9c631e1 ("iavf: Fix deadlock in iavf_reset_task")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jiasheng Jiang [Mon, 14 Mar 2022 01:34:48 +0000 (09:34 +0800)]
atm: eni: Add check for dma_map_single
[ Upstream commit
0f74b29a4f53627376cf5a5fb7b0b3fa748a0b2b ]
As the potential failure of the dma_map_single(),
it should be better to check it and return error
if fails.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Eric Dumazet [Sat, 12 Mar 2022 23:29:58 +0000 (15:29 -0800)]
net/packet: fix slab-out-of-bounds access in packet_recvmsg()
[ Upstream commit
c700525fcc06b05adfea78039de02628af79e07a ]
syzbot found that when an AF_PACKET socket is using PACKET_COPY_THRESH
and mmap operations, tpacket_rcv() is queueing skbs with
garbage in skb->cb[], triggering a too big copy [1]
Presumably, users of af_packet using mmap() already gets correct
metadata from the mapped buffer, we can simply make sure
to clear 12 bytes that might be copied to user space later.
BUG: KASAN: stack-out-of-bounds in memcpy include/linux/fortify-string.h:225 [inline]
BUG: KASAN: stack-out-of-bounds in packet_recvmsg+0x56c/0x1150 net/packet/af_packet.c:3489
Write of size 165 at addr
ffffc9000385fb78 by task syz-executor233/3631
CPU: 0 PID: 3631 Comm: syz-executor233 Not tainted 5.17.0-rc7-syzkaller-02396-g0b3660695e80 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description.constprop.0.cold+0xf/0x336 mm/kasan/report.c:255
__kasan_report mm/kasan/report.c:442 [inline]
kasan_report.cold+0x83/0xdf mm/kasan/report.c:459
check_region_inline mm/kasan/generic.c:183 [inline]
kasan_check_range+0x13d/0x180 mm/kasan/generic.c:189
memcpy+0x39/0x60 mm/kasan/shadow.c:66
memcpy include/linux/fortify-string.h:225 [inline]
packet_recvmsg+0x56c/0x1150 net/packet/af_packet.c:3489
sock_recvmsg_nosec net/socket.c:948 [inline]
sock_recvmsg net/socket.c:966 [inline]
sock_recvmsg net/socket.c:962 [inline]
____sys_recvmsg+0x2c4/0x600 net/socket.c:2632
___sys_recvmsg+0x127/0x200 net/socket.c:2674
__sys_recvmsg+0xe2/0x1a0 net/socket.c:2704
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7fdfd5954c29
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 41 15 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:
00007ffcf8e71e48 EFLAGS:
00000246 ORIG_RAX:
000000000000002f
RAX:
ffffffffffffffda RBX:
0000000000000003 RCX:
00007fdfd5954c29
RDX:
0000000000000000 RSI:
0000000020000500 RDI:
0000000000000005
RBP:
0000000000000000 R08:
000000000000000d R09:
000000000000000d
R10:
0000000000000000 R11:
0000000000000246 R12:
00007ffcf8e71e60
R13:
00000000000f4240 R14:
000000000000c1ff R15:
00007ffcf8e71e54
</TASK>
addr
ffffc9000385fb78 is located in stack of task syz-executor233/3631 at offset 32 in frame:
____sys_recvmsg+0x0/0x600 include/linux/uio.h:246
this frame has 1 object:
[32, 160) 'addr'
Memory state around the buggy address:
ffffc9000385fa80: 00 04 f3 f3 f3 f3 f3 00 00 00 00 00 00 00 00 00
ffffc9000385fb00: 00 00 00 00 00 00 00 00 00 00 00 f1 f1 f1 f1 00
>
ffffc9000385fb80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f3
^
ffffc9000385fc00: f3 f3 f3 00 00 00 00 00 00 00 00 00 00 00 00 f1
ffffc9000385fc80: f1 f1 f1 00 f2 f2 f2 00 f2 f2 f2 00 00 00 00 00
==================================================================
Fixes:
0fb375fb9b93 ("[AF_PACKET]: Allow for > 8 byte hardware addresses.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220312232958.3535620-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Kurt Cancemi [Sat, 12 Mar 2022 20:15:13 +0000 (15:15 -0500)]
net: phy: marvell: Fix invalid comparison in the resume and suspend functions
[ Upstream commit
837d9e49402eaf030db55a49f96fc51d73b4b441 ]
This bug resulted in only the current mode being resumed and suspended when
the PHY supported both fiber and copper modes and when the PHY only supported
copper mode the fiber mode would incorrectly be attempted to be resumed and
suspended.
Fixes:
3758be3dc162 ("Marvell phy: add functions to suspend and resume both interfaces: fiber and copper links.")
Signed-off-by: Kurt Cancemi <kurt@x64architecture.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220312201512.326047-1-kurt@x64architecture.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sabrina Dubroca [Thu, 10 Mar 2022 10:49:00 +0000 (11:49 +0100)]
esp6: fix check on ipv6_skip_exthdr's return value
[ Upstream commit
4db4075f92af2b28f415fc979ab626e6b37d67b6 ]
Commit
5f9c55c8066b ("ipv6: check return value of ipv6_skip_exthdr")
introduced an incorrect check, which leads to all ESP packets over
either TCPv6 or UDPv6 encapsulation being dropped. In this particular
case, offset is negative, since skb->data points to the ESP header in
the following chain of headers, while skb->network_header points to
the IPv6 header:
IPv6 | ext | ... | ext | UDP | ESP | ...
That doesn't seem to be a problem, especially considering that if we
reach esp6_input_done2, we're guaranteed to have a full set of headers
available (otherwise the packet would have been dropped earlier in the
stack). However, it means that the return value will (intentionally)
be negative. We can make the test more specific, as the expected
return value of ipv6_skip_exthdr will be the (negated) size of either
a UDP header, or a TCP header with possible options.
In the future, we should probably either make ipv6_skip_exthdr
explicitly accept negative offsets (and adjust its return value for
error cases), or make ipv6_skip_exthdr only take non-negative
offsets (and audit all callers).
Fixes:
5f9c55c8066b ("ipv6: check return value of ipv6_skip_exthdr")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jiyong Park [Fri, 11 Mar 2022 02:00:16 +0000 (11:00 +0900)]
vsock: each transport cycles only on its own sockets
[ Upstream commit
8e6ed963763fe21429eabfc76c69ce2b0163a3dd ]
When iterating over sockets using vsock_for_each_connected_socket, make
sure that a transport filters out sockets that don't belong to the
transport.
There actually was an issue caused by this; in a nested VM
configuration, destroying the nested VM (which often involves the
closing of /dev/vhost-vsock if there was h2g connections to the nested
VM) kills not only the h2g connections, but also all existing g2h
connections to the (outmost) host which are totally unrelated.
Tested: Executed the following steps on Cuttlefish (Android running on a
VM) [1]: (1) Enter into an `adb shell` session - to have a g2h
connection inside the VM, (2) open and then close /dev/vhost-vsock by
`exec 3< /dev/vhost-vsock && exec 3<&-`, (3) observe that the adb
session is not reset.
[1] https://android.googlesource.com/device/google/cuttlefish/
Fixes:
c0cfa2d8a788 ("vsock: add multi-transports support")
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jiyong Park <jiyong@google.com>
Link: https://lore.kernel.org/r/20220311020017.1509316-1-jiyong@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Niels Dossche [Thu, 10 Mar 2022 23:27:08 +0000 (00:27 +0100)]
alx: acquire mutex for alx_reinit in alx_change_mtu
[ Upstream commit
46b348fd2d81a341b15fb3f3f986204b038f5c42 ]
alx_reinit has a lockdep assertion that the alx->mtx mutex must be held.
alx_reinit is called from two places: alx_reset and alx_change_mtu.
alx_reset does acquire alx->mtx before calling alx_reinit.
alx_change_mtu does not acquire this mutex, nor do its callers or any
path towards alx_change_mtu.
Acquire the mutex in alx_change_mtu.
The issue was introduced when the fine-grained locking was introduced
to the code to replace the RTNL. The same commit also introduced the
lockdep assertion.
Fixes:
4a5fe57e7751 ("alx: use fine-grained locking instead of RTNL")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Link: https://lore.kernel.org/r/20220310232707.44251-1-dossche.niels@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Randy Dunlap [Tue, 1 Mar 2022 04:18:51 +0000 (20:18 -0800)]
efi: fix return value of __setup handlers
[ Upstream commit
9feaf8b387ee0ece9c1d7add308776b502a35d0c ]
When "dump_apple_properties" is used on the kernel boot command line,
it causes an Unknown parameter message and the string is added to init's
argument strings:
Unknown kernel command line parameters "dump_apple_properties
BOOT_IMAGE=/boot/bzImage-517rc6 efivar_ssdt=newcpu_ssdt", will be
passed to user space.
Run /sbin/init as init process
with arguments:
/sbin/init
dump_apple_properties
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc6
efivar_ssdt=newcpu_ssdt
Similarly when "efivar_ssdt=somestring" is used, it is added to the
Unknown parameter message and to init's environment strings, polluting
them (see examples above).
Change the return value of the __setup functions to 1 to indicate
that the __setup options have been handled.
Fixes:
58c5475aba67 ("x86/efi: Retrieve and assign Apple device properties")
Fixes:
475fb4e8b2f4 ("efi / ACPI: load SSTDs from EFI variables")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/
64644a2f-4a20-bab3-1e15-
3b2cdd0defe3@omprussia.ru
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: linux-efi@vger.kernel.org
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Link: https://lore.kernel.org/r/20220301041851.12459-1-rdunlap@infradead.org
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>