cfg80211: Allow non-zero indexes for device specific pair-wise ciphers

Some vendor specific cipher suites require non-zero key indexes for pairwise
keys, but as of currently, the cfg80211 does not allow it.

As validating they cipher parameters for vendor specific cipher suites is the
job of the driver or hardware/firmware, change the cfg80211 to allow also
non-zero pairwise key indexes for vendor specific ciphers.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: remove debug_dump_skb() functions

Now that rx and tx dumps go through the tracing infrastructure,
we no longer need to keep these routines around.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: use tracing for packet tx/rx dump

This adds a few tracepoints to ath5k driver transmit and
receive callbacks in order to record packet traffic.
We record the entire packet in the trace buffer so that
the data can be extracted with trace-cmd and external
plugins.

Compared to the previous debugging calls, this approach
removes an out-of-line function call from the tx and rx
paths in the compiled-in-but-disabled case, while
improving the ability to process the logged data.

A new option, CONFIG_ATH5K_TRACER, is added so that one
may disable the tracepoints completely.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove unused IEEE80211_WEP_NKID

IEEE80211_WEP_NKID is not used in ath9k any more since the key handling code
has been moved to ath/.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Enable 802.11j 4.9GHz frequencies

This enables 4.9GHz frequencies in ath5k if they are allowed as indicated by
the regulatory domain code. Currently this is MKK9_MKKC (0xfe).

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath: Add function to check if 4.9GHz channels are allowed

This adds a helper function to ath/regd.c which can be asked if 4.9GHz channels
are allowed for a given regulatory domain code. This keeps the knowledge of
regdomains and defines like MKK9_MKKC in one place. I'm passing the regdomain
code instead of the ath_regulatory structure because this needs to be called
quite early in the driver inititalization where ath_regulatory is not available
yet in ath5k.

I'm using MKK9_MKKC only because this is the regdomain in the 802.11j enabled
sample cards we got from our vendor. I found some hints in HAL code that this
is used by Atheros to indicate 4.9GHz channels support and that there might be
other domain codes as well, but as I don't have any documentation I'm just
putting in what I need right now. It can be extended later.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Use local variable for capabilities

Shorten some lines and make code more readable.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix tx queue index confusion in debugfs code

Various places printing tx queue information used various different ways to
get a tx queue index for printing statistics. Most of these ways were wrong.

ATH_TXQ_AC_* cannot be used as an index for sc->tx.txq, because it is only
used internally for queue assignment.

One place used WME_AC_* as a queue index for sc->debug.stats.txstats, however
this array uses the ath9k_hw queue number as well.

Fix all of this by always using the ath9k_hw queue number as an index, and
always looking it up by going through sc->tx.txq_map.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fold struct ath_wiphy into struct ath_softc

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove the bf->aphy field

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove support for virtual wiphys

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove the virtual wiphy debugfs interface

It does not make much sense to keep the current virtual wiphy implementation
any longer - it adds significant complexity, has very few users and is still
very experimental. At some point in time, it will be replaced by a proper
implementation in mac80211.

By making the code easier to read and maintain, removing virtual wiphy support
helps with fixing the remaining driver issues and adding further improvements.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: clean up the code that wakes the mac80211 queues

Instead of spreading ath_wake_mac80211_queue() calls over multiple places
in the tx path that process the tx queue for completion, call it only
where the pending frames counter gets decremented, eliminating some
redundant checks.
To prevent queue draining from waking the queues prematurely (e.g. during
a hardware reset), reset the queue stop state when draining all queues,
as the caller in main.c will run ieee80211_wake_queues(hw) anyway.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-linville' of git://git./linux/kernel/git/luca/wl12xx

ath9k: fix misplaced debug code

The commit 'ath9k: Add more information to debugfs xmit file.' added more
debug counters to ath9k and also added some lines of code to ath9k_hw.

Since ath9k_hw is also used by ath9k_htc, its code must not depend on ath9k
data structures. In this case it was not fatal, but it's still wrong, so
the code needs to be moved back to ath9k.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: utilize fw seq counter for mgmt/non-QoS data frames

"mac80211 will properly assign sequence numbers to QoS-data
frames but cannot do so correctly for non-QoS-data and
management frames because beacons need them from that counter
as well and mac80211 cannot guarantee proper sequencing."

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: enable wake-on-lan feature testing

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: update fw/hw headers

This patch syncs up the header files with
the project's main firmware carl9170fw.git.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: clean up enums and unused macros

Remove unused macros and cleanup buffer_type enumeration

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: use DECLARE_EVENT_CLASS

For events that include only the local struct as
their parameter, we can use DECLARE_EVENT_CLASS
and save quite some binary size across segments
as well lines of code.

   text    data     bss     dec     hex filename
 375745   19296     916  395957   60ab5 mac80211.ko.before
 367473   17888     916  386277   5e4e5 mac80211.ko.after
  -8272   -1408       0   -9680   -25d0 delta

Some more tracepoints with identical arguments
could be combined like this but for now this is
the one that benefits most.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git./linux/kernel/git/iwlwifi/iwlwifi-2.6

ath5k: ath5k_setup_channels cleanup and whitespace

Remove useless test_bit - it's not going to happen because of the way this
function is called only when that bit is set.

And fix some whitespace.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: read and backup AR_WA register value even before chip reset on.

We need to read and backup AR_WA register value permanently and reading
this after the chip is awakened results in this register being zeroed out.

This seems to fix the ASPM with L1 enabled issue that we have observed.
The laptop becomes very slow and hangs mostly with ASPM L1 enabled without
this fix.

Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix incorrect macversion and macrev checks

There are few places where we are checking for macversion and revsions
before RTC is powered ON. However we are reading the macversion and
revisions only after RTC is powered ON and so both macversion and
revisions are actully zero and this leads to incorrect srev checks

Incorrect srev checks can cause registers to be configured wrongly and can
cause unexpected behavior. Fixing this seems to address the ASPM issue that
we have observed. The laptop becomes very slow and hangs mostly with ASPM L1
enabled without this fix.

fix this by reading the macversion and revisisons even before we start
using them. There is no reason why should we delay reading this info
until RTC is powered on as this is just a register information.

Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl12xx: disable auto-arp

The auto-arp feature sometimes has unexpected side effects (e.g. firmware
crashes, no ARP replies, etc.)
disable it until it will be solved.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: Increase scan channel dwell time for passive scans

The passive scan channel dwell time currently used is 30-60TU. A typical
beacon interval for AP's is 100TU. This leads to a ~30% worst-case probability
of finding an AP via passive scanning.

For 5GHz bands for DFS frequencies passive scanning is the only scanning
option. Hence for these, the probability of finding an AP is very low.

To fix this, increase the passive channel scan dwell times (also the early
leave value, as 5GHz channels are still typically very silent.) Use a value
of 100TU, because that covers most typical AP configurations.

Based on testing the probability of finding an AP (100TU beacon interval) on
a single scan round are as follows (based on 100 iterations):

dwell min/max (TU)   | probability
---------------------+------------
30/60                | 35%
60/60                | 56%
80/80                | 77%
100/100              | 100%

Total scan times now and after the change:

Region | Before (s) | After (s)
-------+------------+----------
00     | 0.77       | 1.48
FI     | 0.95       | 2.01
US     | 0.91       | 1.76

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: wrong values are returned in gpio_power_write()

Return values were assigned to incorrect var / weren't assigned.
fix it, and defer mutex_lock after the sanity checks.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: BA receiver support

Add new ampdu_action ops to support receiver BA.
The BA initiator session management in FW independently.

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: BA initiator support

Add 80211n BA initiator session support wl1271 driver.
Include BA supported FW version auto detection mechanism.
BA initiator session management included in FW independently.

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: Add channel 14 to list of supported 2ghz channels

Channel 14 is only supported in Japan (JP country code in regdb).  The
FW limits tranmissions to CCK only on this channel.

Tested in both STA and AP modes to work correctly.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: add missing MODULE_FIRMWARE statment for AP-mode FW

In wl12xx cards AP-mode requires a separate FW file. Add this file to
the module info.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: Cleanup PLT mode when module is removed

PLT mode start/stop is controlled from userspace. When removing module, the
PLT mode state is however not checked, and not cleared. There is the possibility
of some unwanted state to left linger and there is even the possiblity of a
kernel crash if for instance IRQ work is running when the module is removed.

Fix this by stopping PLT mode on module removal, if still running.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: fix some endianess bugs

pointed out by sparse warnings:

  CHECK   drivers/net/wireless/wl12xx/cmd.c
drivers/net/wireless/wl12xx/cmd.c:987:20: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/cmd.c:987:20:    expected restricted __le16 [usertype] aging_period
drivers/net/wireless/wl12xx/cmd.c:987:20:    got int
  CHECK   drivers/net/wireless/wl12xx/tx.c
drivers/net/wireless/wl12xx/tx.c:197:2: warning: cast from restricted __le16
drivers/net/wireless/wl12xx/tx.c:197:2: warning: cast from restricted __le16
drivers/net/wireless/wl12xx/tx.c:197:2: warning: cast from restricted __le16
  CHECK   drivers/net/wireless/wl12xx/acx.c
drivers/net/wireless/wl12xx/acx.c:816:23: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/acx.c:816:23:    expected restricted __le32 [usertype] rate_policy_idx
drivers/net/wireless/wl12xx/acx.c:816:23:    got unsigned char [unsigned] [usertype] idx

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: add hw configuration for max supported AMDPU size

The wl12xx chips do the AMDPU aggregation work in the firmware, but it
supports a maximum of 8 frames per block.  Configure the mac80211 hw
structure accordingly.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Tested-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>

wl12xx: change debug_level module param sysfs permissions

changed the visibility of the debug_level module parameter
in the filesystem to be readable and writable to the root user.
It is now accessible under /sys/module/wl12xx/parameters

removed the debug_level debugfs file that was created under
/sys/kernel/debug/...

Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: lock the RCU when accessing sta via ieee80211_find_sta()

We were calling ieee80211_find_sta() and the sta returned by it
without locking the RCU, which is required by mac80211.

Fix this and reorganize slightly the area of the code where the sta is
used.

Reported-by: Jonathan DE CESCO <jonathanc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: don't modify the global supported band structures

When 11a is not supported, we were modifying the global structure that
contains the bands supported by the driver.  This causes problems when
having more one wl12xx device in the same system because they all use
the same global.  This also causes problems when the wl12xx_sdio
module is removed and the wl12xx module remains.

Fix this problem by copying the band structure into the wl12xx
instance.

Reported-by: Arik Nemtsov <arik@wizery.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: don't join upon disassociation

wl12xx "rejoins" upon every BSS_CHANGED_BSSID notification.
However, there is no need to rejoin after disassociation, so just
filter out the case when the new bssid is 00:00:00:00:00:00.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

MAINTAINERS: update information for the wl12xx driver

Update maintainer's email address, webpage and align with renaming of
files.

Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: Enable AP-mode

Indicate support for the NL80211_IFTYPE_AP interface mode to enable AP
mode operation.

Disable 11a when operating in AP-mode (unsupported for now).

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: Read MAC address from NVS file on HW startup

Try to read the MAC address from the on-disk NVS file.
A non-zero MAC address is required to add an AP interface.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: AP mode - fetch appropriate firmware for AP

AP and STA modes use different firmwares.

Differentiate the firmware files by name and fetch the appropriate one
when add_interface is called by mac80211. The STA firmware is chosen for
PLT mode.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: AP mode - encryption support

Encryption key configuration is different for AP/STA modes.

AP encryption keys are recorded when the BSS is not started. On BSS
start they are propagated to the AP (in wl1271_ap_init_hwenc).

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: AP mode - record TX configuration settings

Record TX configuration settings in the "conf" member of our global
structure (struct wl1271) if conf_tx is called when the firmware is
not loaded.

Later on when the firmware is loaded, we apply the tx conf as part of
the init sequence.

Important for AP mode since conf_tx is called before add_interface
(where the firmware is initialized).

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: AP mode - changes in TX path

When in AP mode set appropriate HLID and rate policy for each skb.
Respond to supported-rates related changes in op_tx only when acting
as STA.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: AP mode - add STA add/remove ops

Allocate and free host link IDs (HLIDs) for each link. A per-STA
data structure keeps the HLID of each STA.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: AP mode - change filter config

Do not configure a group address table in AP mode

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: AP mode config in ieee80211_ops.config

Separate configuration according to mode. AP has different rate
set configuration and no handling of idle-state.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: Configure AP on BSS info change

Configure AP-specific beacon and probe response templates.
Start the AP when beaconing is enabled.

The wl1271_bss_info_changed() function has been split into AP/STA
specific handlers.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: Add AP related definitions to HOST-FW interface

Change structures in a non-destructive manner. This means no
changes in size or location of existing members used by STA.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: AP specific RX filter configuration

Set filters according to the mode of operation.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: AP mode - init sequence

Split HW init sequence into AP/STA specific parts

The AP specific init sequence includes configuration of templates, rate
classes, power mode, etc. Also unmask AP specific events in the event mbox.

Separate the differences between AP and STA init into mode
specific functions called from wl1271_hw_init. The first is called after
radio configuration and the second after memory configuration.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: AP mode - workaround for FW bug on station remove

Sometimes an event indicating station removal is not sent up by
firmware. We work around this by always indicating success in when
a wait for the event timeouts.

Temporary workaround until a FW fix is introduced.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: AP-mode high level commands

Add commands to start/stop BSS, add/remove STA and configure encryption
keys. Split the encryption commands "set key" and "set default key" into
AP and STA specific versions.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: AP mode - add AP specific event

Add STA-remove completion event. Unmask it during boot if operating in
AP-mode.
Ignore unrelated events in AP-mode.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: AP mode - AP specific CMD_CONFIGURE sub-commands

Add AP max retries and rate policy configuration.
Rename STA rate policy configuration function.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: Add AP related configuration to conf_drv_settings

Rate class configuration has been split up for AP and STA modes.
Template related configuration likewise separated.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: fix some sparse warnings

Note that wl1271_write32() calls cpu_to_le32() by itself, so calling
wl1271_write32(addr, cpu_to_le32(val)) is in fact a bug on BE systems.

Fix the following sparse warnings:

drivers/net/wireless/wl12xx/cmd.c:662:16: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/cmd.c:662:16:    expected unsigned short [unsigned] [addressable] [usertype] llc_type
drivers/net/wireless/wl12xx/cmd.c:662:16:    got restricted __be16 [usertype] <noident>
drivers/net/wireless/wl12xx/cmd.c:674:17: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/cmd.c:674:17:    expected unsigned int [unsigned] [addressable] [usertype] sender_ip
drivers/net/wireless/wl12xx/cmd.c:674:17:    got restricted __be32 [usertype] ip_addr
drivers/net/wireless/wl12xx/rx.c:202:4: warning: incorrect type in argument 3 (different base types)
drivers/net/wireless/wl12xx/rx.c:202:4:    expected unsigned int [unsigned] [usertype] val
drivers/net/wireless/wl12xx/rx.c:202:4:    got restricted __le32 [usertype] <noident>
drivers/net/wireless/wl12xx/acx.c:1247:23: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/acx.c:1247:23:    expected restricted __le32 [usertype] ht_capabilites
drivers/net/wireless/wl12xx/acx.c:1247:23:    got unsigned long
drivers/net/wireless/wl12xx/acx.c:1250:24: warning: invalid assignment: |=
drivers/net/wireless/wl12xx/acx.c:1250:24:    left side has type restricted __le32
drivers/net/wireless/wl12xx/acx.c:1250:24:    right side has type unsigned long
drivers/net/wireless/wl12xx/acx.c:1253:24: warning: invalid assignment: |=
drivers/net/wireless/wl12xx/acx.c:1253:24:    left side has type restricted __le32
drivers/net/wireless/wl12xx/acx.c:1253:24:    right side has type unsigned long
drivers/net/wireless/wl12xx/acx.c:1256:24: warning: invalid assignment: |=
drivers/net/wireless/wl12xx/acx.c:1256:24:    left side has type restricted __le32
drivers/net/wireless/wl12xx/acx.c:1256:24:    right side has type unsigned long

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: use after free in debug code

If debugging is turned on, then wl1271_dump() dereferences a freed
variable.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>

wl12xx: remove redundant debugfs_remove_recursive() call

Upon rmmod, the <debugfs>/ieee80211/phyX dir is being removed.
later, we try to remove <debugfs>/ieee80211/phyX/wl12xx, which
might result in NULL dereference.

Remove the excessive debugfs_remove_recursive() call.
(consequently, there is no more need to save wl->rootdir)

Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>

iwlwifi: initial P2P support

If PAN functionality is present, advertise
P2P interface type support and thus support
for P2P. However, the support is currently
somewhat incomplete -- NoA schedule isn't
added to probe responses, and 11b bitrates
may be used still, etc. Therefore, make it
all optional with a Kconfig option.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: replace minimum slot time constant

There are a number of places where the minimum
slot time is hardcoded to 20 TU, add a new
constant for that and use it everywhere.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: implement remain-on-channel

For device supporting PAN/P2P, use the PAN
context to implement the remain-on-channel
operation using device offloads so that the
filters in the device will be programmed
correctly -- otherwise we cannot receive
any probe request frames during off-channel
periods.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlagn: Enable idle powersave mode in 1000 series

The iwlagn powersave algorithm uses the supports_idle parameter
to tell the device to save power when it is not associated with
an AP and is idle.

Enable this feature for the 1000 series of devices.

Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: correct debugfs data dumped from sram

the sram data dumped through the debugfs interface would only work properly
when dumping data on even u32 boundaries and swap bytes based on endianness
on that boundary making byte arrays impossible to read.

now addresses are displayed at the start of every line and the data is
displayed consistently if dumping 1 byte or 20 and regardless of what is the
starting address.

if no lenght given, address displayed is u32 in device format

Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: add hw rev for 2000 series devices

2000 series device has different HW rev, add it

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: remove g2 from csr hw rev

Remove refernce of g2 and use offical number for hw rev.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: remove Gen2 from Kconfig

Remove Gen 2 from Kconfig file since 6005/6030/6150 series of
products are released.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: add 2000 series to Kconfig

Add 2000 series support to Kconfig

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: add 2000 series pci id

Add PCI ID supports for all 2000 series devices

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

 iwlagn: 2000 series devices support

Adding 2000 series devices supports, the 2000 series devices has
many different SKUs which includes 1x1 and 2x2 devices,also with
and without BT combo.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: add 2000 series EEPROM version

Adding EEPROM version for 2000 series devices

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: remove reference to gen2a and gen2b

Since 6005, 6030 and 6150 series are offical released, remove the reference
to gen2x and use the product number instead.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: use mac80211 throughput trigger

Instead of keeping track of LED blink speed
in the driver, use the new mac80211 trigger
and link it up with an LED classdev that we
now register. This also allows users more
flexibility in how they want to have the LED
blink or not.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

ath9k_hw: replace magic values in register writes with proper defines

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Simplify loop when setting up channels

Simplify confusing code and get rid of an unnecessary variable.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove a bogus error message

When beacons are being added or removed for an interface, ieee80211_beacon_get
will sometimes not return a beacon. This is normal and should not result in
useless logspam.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Remove redundant sc->curband

Remove sc->curband because the band is already stored in the current channel.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Remove unused sc->curmode

sc->curmode is set but never used. Remove it and the helper function. Also the
ath5k_rate_update which is refered to in the comment does not exist (any more?)
so we don't need to setup the band in that place.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5: Remove unused CTL definitions

They are unused in ath5k and a more detailled definition is in
ath/regd_common.h.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Add 802.11j 4.9GHz channels to allowed channels

Add the 802.11j (20MHz channel width) channels to the allowed channels. This
still does not enable 802.11j in ath5k since these frequencies are out of the
configured range. A later patch will deal with that.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Rename ath5k_copy_channels

Rename ath5k_copy_channels() to ath5k_setup_channels() - nothing is copied
here.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Use mac80211 channel mapping function

Use mac80211 channel mapping function instead of own homegrown version.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Try more than one queue when scheduling new aggregate.

Try all xmit queues until the hardware buffers are full.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add 'misc' file to debugfs, fix queue indexes.

Add a misc file to show hardware op-mode, irq setup,
number of various types of VIFs and more.

Also, previous patches were using the wrong xmit queue
indexes.  Change to use the internal ath9k indexes instead
of the mac80211 queue indexes.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: Extend channel to frequency mapping for 802.11j

Extend channel to frequency mapping for 802.11j Japan 4.9GHz band, according to
IEEE802.11 section 17.3.8.3.2 and Annex J. Because there are now overlapping
channel numbers in the 2GHz and 5GHz band we can't map from channel to
frequency without knowing the band. This is no problem as in most contexts we
know the band. In places where we don't know the band (and WEXT compatibility)
we assume the 2GHz band for channels below 14.

This patch does not implement all channel to frequency mappings defined in
802.11, it's just an extension for 802.11j 20MHz channels. 5MHz and 10MHz
channels as well as 802.11y channels have been omitted.

The following drivers have been updated to reflect the API changes:
iwl-3945, iwl-agn, iwmc3200wifi, libertas, mwl8k, rt2x00, wl1251, wl12xx.
The drivers have been compile-tested only.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Brian Prodoehl <bprodoehl@gmail.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Restart xmit logic in xmit watchdog.

The system can get into a state where the xmit queue
is stopped, but there are no packets pending, so
the queue will not be restarted.

Add logic to the xmit watchdog to attempt to restart
the xmit logic if this situation is detected.

Example 'dmesg' output:

ath: txq: f4e723e0 axq_qnum: 2, mac80211_qnum: 2 axq_link: f4e996c8 pending frames: 1 axq_acq empty: 1 stopped: 0 axq_depth: 0  Attempting to restart tx logic.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: More xmit queue debugfs information.

To try to figure out why xmit logic hangs.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Keep track of stations for debugfs.

The stations hold the ath_node, which holds the tid
and other xmit logic structures.  In order to debug
stuck xmit logic, we need a way to print out the tid
state for the stations.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add counters to distinquish AMPDU enqueues.

Show counters for pkts sent directly to hardware and
those queued in software.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Ensure xmit makes progress.

If the txq->axq_q is empty, the code was breaking out
of the tx_processq logic without checking to see if it should
transmit other queued AMPDU frames (txq->axq_acq).

This patches ensures ath_txq_schedule is called.

This needs review.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove un-used member from ath_node.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add more information to debugfs xmit file.

Should help debug strange tx lockup type issues.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Initialize ah->hw

Previous code left it NULL.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Show some live tx-queue values in debugfs.

I thought this might help track down stuck queues, etc.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Fix skb-copy failure debug message.

This particular error isn't about multicast.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix 4965 notification wait setup

The notification wait support code is shared
between 4965 and other AGN devices, so 4965
also has to initialize the data structures
for it, otherwise it crashes.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: return error if PAN disable timeout

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: properly wait for PAN disable

Previously I hacked this with an msleep(300)
which was fine since we never had longer PAN
time slots, but now that we will have them I
need to fix that. Use the new notification
wait support to properly wait for the WIPAN
deactivation complete signal from the ucode.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: add support for waiting for notifications

In order to implement waiting for notifications,
add a structure that captures the information,
and a list of such structures that will be
traversed when a command is received from the
ucode.

Use sparse checking to make sure calls to the
prepare/wait/cancel functions are always nested
correctly.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>