Don Fry [Thu, 1 Dec 2011 00:58:39 +0000 (16:58 -0800)]
iwlwifi: move calib_results list from iwl_priv to iwl_trans
Move the calib_results list from the upper layer iwl_priv structure
to the lower layer iwl_trans structure.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Don Fry [Thu, 1 Dec 2011 00:12:59 +0000 (16:12 -0800)]
iwlwifi: move device_pointers from iwl_priv to iwl_shared
Move the low level ucode device_pointers structure to iwl_shared.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Don Fry [Wed, 30 Nov 2011 23:37:32 +0000 (15:37 -0800)]
iwlwifi: move eeprom pointer from iwl_priv to iwl_shared
The eeprom image is a device level component, move from iwl_priv
to iwl_shared, with associated code changes.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Fri, 2 Dec 2011 16:09:10 +0000 (08:09 -0800)]
iwlwifi: set TX_CMD_FLG_STA_RATE_MSK for BAR frame
It is needed by firmware to use the correct rate for BAR frame transmission
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Fri, 2 Dec 2011 15:33:57 +0000 (07:33 -0800)]
iwlwifi: P2P is not enabled by default
P2P still under development. it will not enabled by default, but user
always can enable it manually for testing.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Hsu, Kenny [Thu, 1 Dec 2011 09:12:50 +0000 (01:12 -0800)]
iwlwifi: add device ID information support by testmode
Create new tm command to report devce ID information to userspace
- IWL_TM_CMD_APP2DEV_GET_DEVICE_ID
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Wed, 30 Nov 2011 21:24:06 +0000 (13:24 -0800)]
iwlwifi: rename CONFIG_IWLWIFI_DEVICE_SVTOOL to CONFIG_IWLWIFI_DEVICE_TESTMODE
Change the name to match the works
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Wed, 30 Nov 2011 08:14:53 +0000 (00:14 -0800)]
iwlwifi: remove reference to legacy devices
After driver split, no need to reference to legacy devices, remove comments
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Wed, 30 Nov 2011 17:41:22 +0000 (09:41 -0800)]
iwlwifi: minor cleanup
Remove the defines only used by legacy devices
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Wed, 30 Nov 2011 20:32:42 +0000 (12:32 -0800)]
iwlwifi: Display more uCode debug info
When uCode encounter problem, it pass a lot of debug data to help debugging
the issue. We only show partial data before, why not display all of those.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Hsu, Kenny [Tue, 29 Nov 2011 00:54:52 +0000 (16:54 -0800)]
iwlwifi: hide kernel option IWLWIFI_DEVICE_SVTOOL
Because the testmode support should be the mandatory foundation
of test functionality, it is better to set kernel option
IWLWIFI_DEVICE_SVTOOL automatically instead of user configuration.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Hsu, Kenny [Mon, 28 Nov 2011 08:55:38 +0000 (00:55 -0800)]
iwlwifi: add uCode version information support by testmode
Create new tm command to report uCode version to userspace
- IWL_TM_CMD_APP2DEV_GET_FW_VERSION
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Thu, 8 Dec 2011 23:00:27 +0000 (15:00 -0800)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next into wireless-next
Luciano Coelho [Thu, 8 Dec 2011 11:08:10 +0000 (13:08 +0200)]
Merge branch 'wl12xx-next' into for-linville
Eyal Shapira [Wed, 7 Dec 2011 10:37:04 +0000 (12:37 +0200)]
wl12xx: minor fix in sched_scan_ssid_list
The user can pass broadcast SSID (ssid="") in the list of SSIDs for active scan.
In this case the loop was attempting to match SSIDs in the filter
list to this empty entry and marking them as HIDDEN (sending probe
request) by mistake
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Tue, 6 Dec 2011 10:15:07 +0000 (12:15 +0200)]
wl12xx: send testmode reply in wl1271_tm_cmd_interrogate
wl1271_tm_cmd_interrogate creates a reply skb, but doesn't
send it (and thus just leaks it).
Add the missing cfg80211_testmode_reply() call.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Tue, 6 Dec 2011 10:15:06 +0000 (12:15 +0200)]
wl12xx: remove redundant commands from plt init
During plt init we configure some redundant commands,
which are not needed for plt (specifically, we shouldn't
configure any role-specific params, as there are no
active roles). remove them.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Tue, 6 Dec 2011 10:15:05 +0000 (12:15 +0200)]
wl12xx: fix testmode test/interrogate commands
fix several issues in testmode test/interrogate commands:
1. check the driver state is not OFF.
2. wakeup the chip from elp (if needed)
3. fix memory leak in wl1271_tm_cmd_interrogate()
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Johannes Berg [Tue, 6 Dec 2011 19:45:37 +0000 (20:45 +0100)]
wireless: disable wext sysfs by default
This code has been on the list to remove for a long
time, so disable it by default, add a warning to its
Kconfig, and schedule it for removal in 3.5.
The only known dependency, hal, has not required it
since its 0.5.12 release, which was in early 2009
and hal has since been deprecated completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nikolay Martynov [Wed, 7 Dec 2011 02:57:17 +0000 (21:57 -0500)]
ath9k: enable ANI for ar9100 chips
Enable ANI for ar9100 since it seems to be working fine (and as a
matter of fact ANI was always performed for ar9100 since code which
was supposed to disable it didn't achieve this goal).
This patch sets config.enable_ani to default (true) value for
ar9100.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nikolay Martynov [Sat, 3 Dec 2011 03:39:16 +0000 (22:39 -0500)]
ath9k: use config.enable_ani to check if ani should be performed
Currently in ath9k code there is an attempt which is meant to
disable ANI for ar9100 and ar9340. But it doesn't really achieve
this. All it does is disable ANI init and setup (i.e. calls to
ath9k_hw_ani_setup and ath9k_hw_ani_init). Since ath9k_hw_ani_setup is
not called ah->config.ani_poll_interval is never initialized (i.e. it
is always zero) and ath_ani_calibrate always executes ANI procedures
(over uninitialized ANI parameters).
Moreover, ath_ani_calibrate is being called each 1ms because
common->ani.timer is set to zero interval because
ah->config.ani_poll_interval==0 (and thus smallest value of all
intervals). Normally it should not be called this often.
This patch changes the code so config.enable_ani is used to check if
ANI should be performed.
config.enable_ani is initialized to true by default. This patch sets
it to false for ar9100 and ar9340.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nikolay Martynov [Sat, 3 Dec 2011 03:39:15 +0000 (22:39 -0500)]
ath9k: change calibration debug log to output all calibration types
To help debugging write a log entry when long calibration, short
calibration or ANI is performed.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nikolay Martynov [Sat, 3 Dec 2011 03:39:14 +0000 (22:39 -0500)]
ath9k: trivial: cosmetic fix in calibration debug log
Add missed space and change typo in calibration debugging log.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 16 Nov 2011 12:08:43 +0000 (13:08 +0100)]
ath9k: cancel all workqueue activity when going idle
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 16 Nov 2011 12:08:42 +0000 (13:08 +0100)]
ath9k: only drop packets in drv_flush when asked to
Recently more places in mac80211 call drv_flush to ensure proper order
for state changes wrt. powersave, channel changes, etc. On some systems
such calls lead to spurious logspam about failing to stop tx dma, as well
as hardware resets that go along with that.
Instead of dropping packets in a place where it's completely unnecessary,
only do it when drop == true.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 16 Nov 2011 12:08:41 +0000 (13:08 +0100)]
ath9k: rework power state handling
Turning off the radio when mac80211 tells the driver that it's idle is not
a good idea, as idle interfaces might still occasionally scan or send packets.
The only time the radio can be safely turned off is when drv_stop has been
called. In the mean time, use sc->ps_idle only to indicate network sleep vs
full sleep.
Move the LED GPIO changes out of the PCI suspend/resume path, the start/stop
functions already take care of that.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 16 Nov 2011 12:08:40 +0000 (13:08 +0100)]
ath9k: always issue a full hw reset after waking up from full-sleep mode
After waking up from full sleep, registers are accessible, but rx/tx
typically fails. A fast channel change will not recover from this, so
ensure that a full-sleep -> wake transition is always followed by a full
reset.
The reason why this hasn't created any serious problems yet is that it's
hidden by the (wrong) behavior of enabling/disabling the radio when the
wiphy idle state changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Greear [Mon, 5 Dec 2011 19:15:55 +0000 (11:15 -0800)]
mac80211: Remove WARN_ON in apply-ht-override logic.
AP interfaces routinely call this logic, so just silently
return when this happens instead of splatting the kernel
logs.
Reported-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Mon, 5 Dec 2011 18:13:39 +0000 (19:13 +0100)]
bcma: pci: use fixed windows when possible
Some cores are mapped in the fixed way, they registers can be accessed
all the time.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 6 Dec 2011 09:39:40 +0000 (10:39 +0100)]
mac80211: accept public action frames with mismatched BSSID
Arik's patch "mac80211: allow action frames with unknown
BSSID in GO mode" allowed any action frames in P2P mode
to go through, but only to cooked monitor interfaces as
the IEEE80211_RX_RA_MATCH was still cleared. As a result
my no-monitor patches broke invitation responses.
Instead of allowing any action frames in P2P GO mode to
go through with a wrong BSSID like that patch did, allow
all public action frames. They will never be processed
by mac80211, but can be reported via nl80211 then.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 2 Dec 2011 21:08:52 +0000 (22:08 +0100)]
mac80211: fix retransmit
This fixes another regression from my "pass all
fragments to driver at once" patches -- if the
packet is being retransmitted then we don't go
through all handlers, but we still need to move
it to the skbs list, otherwise we run into the
first warning in __ieee80211_tx() and leak the
skb.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don Fry [Fri, 2 Dec 2011 16:48:40 +0000 (08:48 -0800)]
iwlwifi: move ucode notification from iwl_priv to iwl_shared
Move the notification structures for ucode operations from the
iwl_priv structure to the iwl_shared structure, with associated
code changes.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don Fry [Fri, 2 Dec 2011 16:48:39 +0000 (08:48 -0800)]
iwlwifi: move ucode_type from iwl_priv to iwl_shared
Move the ucode_type variable from the iwl_priv to the iwl_shared
structure with associated code changes.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don Fry [Fri, 2 Dec 2011 16:48:38 +0000 (08:48 -0800)]
iwlwifi: replace iwl_priv reference with iwl_trans for ucode.
Replace the references to the iwl_priv structure with the iwl_trans
structure as the priv structure is never referenced other than to
access the trans structure. Rename from iwlagn to iwl.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don Fry [Fri, 2 Dec 2011 16:48:37 +0000 (08:48 -0800)]
iwlwifi: rename iwl-agn-ucode as iwl-ucode
iwl-agn-ucode is generic ucode operations, not limited just to iwlagn.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 2 Dec 2011 16:48:36 +0000 (08:48 -0800)]
iwlwifi: Rename file name from iwl-sv-open.c to iwl-testmode.c
The file dealing with all the operations through testmode, rename it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hsu, Kenny [Fri, 2 Dec 2011 16:48:35 +0000 (08:48 -0800)]
iwlwifi: add WOWLAN uCode loading support by testmode
Create new tm command for WOWLAN uCode loading to support
further debugging function in userspace.
- IWL_TM_CMD_APP2DEV_LOAD_WOWLAN_FW
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 2 Dec 2011 16:48:34 +0000 (08:48 -0800)]
iwlagn: make debug levels more readable
Using the actual shifted constants here allows
one to read and or them more easily.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 2 Dec 2011 16:48:33 +0000 (08:48 -0800)]
iwlagn: remove MACDUMP debug
This is only used for TX debugging where there
already is more debugging and tracing is more
useful anyway, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 2 Dec 2011 16:48:32 +0000 (08:48 -0800)]
iwlagn: remove HC_DUMP debug
This debug level is unused, remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 2 Dec 2011 16:48:31 +0000 (08:48 -0800)]
iwlagn: remove TX_REPLY_LIMIT debug
This macro is unused right now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 2 Dec 2011 16:48:29 +0000 (08:48 -0800)]
iwlwifi: declare static for iwl_sram_cleanup function
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hsu, Kenny [Fri, 2 Dec 2011 16:48:28 +0000 (08:48 -0800)]
iwlwifi: add generic chunk size of tm dumpit packet
Use generic chunk size of dumpit packet for
all necessary testmode commands instead of
add declaration individually.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kenny Hsu [Fri, 2 Dec 2011 16:48:27 +0000 (08:48 -0800)]
iwlwifi: add range checking in tm sram read command
The size of sram may alter according to ucode type.
Retrieve the maximum sram size by current ucode
type for range checking to prevent wrong data access.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hsu, Kenny [Fri, 2 Dec 2011 16:48:26 +0000 (08:48 -0800)]
iwlwifi: add tm commands for sram reading by dumpit
Create new testmode commands and attributes to suppot
sram data reading. Because the amount of sram data
may exceed single skb packet size. Using the nl80211
dump it funtion to deliver sram data to userspace.
- IWL_TM_CMD_APP2DEV_READ_SRAM
- IWL_TM_CMD_APP2DEV_DUMP_SRAM
- IWL_TM_ATTR_SRAM_ADDR
- IWL_TM_ATTR_SRAM_SIZE
- IWL_TM_ATTR_SRAM_DUMP
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Thu, 1 Dec 2011 12:44:01 +0000 (18:14 +0530)]
ath9k: clarify max_streams for AR9462
max_streams for AR9462 is '2'. it does not fixes anything, but
improves the code readability
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Thu, 1 Dec 2011 05:44:19 +0000 (11:14 +0530)]
ath9k_hw: sync to latest AR9462 INI
based on systems change to improve rx dynamic range,
and enables heavy clip for 5G HT40 MCS0 to improve
spectral mask power. also remove an unused function
declaration
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Wed, 30 Nov 2011 16:58:14 +0000 (10:58 -0600)]
rtl8192c: Do not log firmware load message unless actually done
A previous commit fixed a problem whereby the rtl8192c driver loaded the
firmware from disk many times; however, the log message was not moved.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alexander Simon [Wed, 30 Nov 2011 15:56:34 +0000 (16:56 +0100)]
mac80211: Add HT operation modes for IBSS
The HT mode is set by iw (previous patchsets).
The interface is set into the specified HT mode.
HT mode and capabilities are announced in beacons.
If we add a station that uses HT also, the fastest matching HT mode will
be used for transmission. That means if we are using HT40+ and we add a station
running on HT40-, we would transfer at HT20.
If we join an IBSS with HT40, but the secondary channel is not
available, we will fall back into HT20 as well.
Allow frame aggregation to start in IBSS mode.
Signed-off-by: Alexander Simon <an.alexsimon@googlemail.com>
[siwu@hrz.tu-chemnitz.de: Updates]
* remove implicit channel_type enum assumptions
* use rate_control_rate_init() if channel type changed
* remove channel flags check
* activate HT IBSS feature support
* slightly reword commit message
* rebase on wireless-testing
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simon Wunderlich [Wed, 30 Nov 2011 15:56:33 +0000 (16:56 +0100)]
mac80211: handle protection mode, RIFS and ADDBA for HT IBSS
* Follow 802.11n-2009 9.13.3.1 for protection mode and ADDBA
* Send ADDBA only to HT STAs - implement 11.5.1.1 partially
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alexander Simon [Wed, 30 Nov 2011 15:56:32 +0000 (16:56 +0100)]
nl80211: Parse channel type attribute in an ibss join request
Prepare cfg80211 for IBSS HT:
* extend cfg80211 ibss struct with channel_type
* Check if extension channel can be used
* Export can_beacon_sec_chan for use in mac80211 (will be called
from ibss.c later).
Signed-off-by: Alexander Simon <an.alexsimon@googlemail.com>
[siwu@hrz.tu-chemnitz.de: Updates]
* fix cfg80211_can_beacon_ext_chan comment
* remove implicit channel_type enum assumptions
* remove radar channel flags check
* add HT IBSS feature flag
* reword commit message
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thomas Meyer [Tue, 29 Nov 2011 21:08:00 +0000 (22:08 +0100)]
iwlegacy: Use kcalloc instead of kzalloc to allocate array
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thomas Meyer [Tue, 29 Nov 2011 21:08:00 +0000 (22:08 +0100)]
rt2x00: Use kcalloc instead of kzalloc to allocate array
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 6 Dec 2011 21:02:05 +0000 (16:02 -0500)]
Merge branch 'master' of git://git./linux/kernel/git/padovan/bluetooth-next
Andrei Emeltchenko [Thu, 1 Dec 2011 12:33:28 +0000 (14:33 +0200)]
Bluetooth: trivial: correct check for LMP version
Make sure that code match exactly what comment says about pre 1.2
bluetooth version. Since this is HCI detail lmp_ver changed to hci_ver.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andrei Emeltchenko [Thu, 1 Dec 2011 12:33:27 +0000 (14:33 +0200)]
Bluetooth: Remove magic bluetooth version numbers
Use bluetooth names instead of BT SIG assigned numbers
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Gustavo F. Padovan [Fri, 2 Dec 2011 23:26:25 +0000 (08:26 +0900)]
Merge branch 'master' of git://git./linux/kernel/git/padovan/bluetooth
Andrei Emeltchenko [Wed, 23 Nov 2011 09:23:34 +0000 (11:23 +0200)]
Bluetooth: Correct version check in hci_setup
Check for hci_ver instead of lmp_ver
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Cong Wang [Tue, 22 Nov 2011 01:32:57 +0000 (09:32 +0800)]
btusb: fix a memory leak in btusb_send_frame()
This patch fixes the following memory leak reported by kmemleak:
unreferenced object 0xffff880060a53840 (size 192):
comm "softirq", pid 0, jiffies
4320571771 (age 1406.569s)
hex dump (first 32 bytes):
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<
ffffffff81138a1c>] create_object+0x187/0x28b
[<
ffffffff814be12e>] kmemleak_alloc+0x73/0x98
[<
ffffffff811289d3>] __kmalloc+0xfc/0x123
[<
ffffffff81386546>] usb_alloc_urb+0x1e/0x48
[<
ffffffffa0130274>] btusb_send_frame+0x86/0x385 [btusb]
[<
ffffffffa02d8230>] hci_send_frame+0xa0/0xa5 [bluetooth]
[<
ffffffffa02d8a4e>] hci_cmd_task+0xa0/0xfb [bluetooth]
[<
ffffffff81058548>] tasklet_action+0x8f/0xef
[<
ffffffff81058a4c>] __do_softirq+0xf4/0x1db
[<
ffffffff81058bb7>] run_ksoftirqd+0x84/0x129
[<
ffffffff8106f1c4>] kthread+0xa0/0xa8
[<
ffffffff814dd144>] kernel_thread_helper+0x4/0x10
[<
ffffffffffffffff>] 0xffffffffffffffff
The problem is that when inc_tx() returns non-zero, we forgot
to call usb_free_urb().
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: "Gustavo F. Padovan" <padovan@profusion.mobi>
Signed-off-by: WANG Cong <amwang@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
John W. Linville [Fri, 2 Dec 2011 20:44:03 +0000 (15:44 -0500)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless
Conflicts:
drivers/net/wireless/iwlwifi/iwl-agn.c
drivers/net/wireless/libertas/cfg.c
Wey-Yi Guy [Fri, 2 Dec 2011 16:19:19 +0000 (08:19 -0800)]
iwlwifi: change the default behavior of watchdog timer
The current default watchdog timer is enabled, but we are seeing issues on
legacy devices. So change the default setting of watchdog timer to per
device based. But user still can use the "wd_disable" module parameter
to overwrite the system setting
Cc: stable@vger.kernel.org #3.0+
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 2 Dec 2011 16:19:18 +0000 (08:19 -0800)]
iwlwifi: do not re-configure HT40 after associated
The ht40 setting should not change after association unless channel switch
This fix a problem we are seeing which cause uCode assert because driver
sending invalid information and make uCode confuse
Here is the firmware assert message:
kernel: iwlagn 0000:03:00.0: Microcode SW error detected. Restarting 0x82000000.
kernel: iwlagn 0000:03:00.0: Loaded firmware version: 17.168.5.3 build 42301
kernel: iwlagn 0000:03:00.0: Start IWL Error Log Dump:
kernel: iwlagn 0000:03:00.0: Status: 0x000512E4, count: 6
kernel: iwlagn 0000:03:00.0: 0x00002078 | ADVANCED_SYSASSERT
kernel: iwlagn 0000:03:00.0: 0x00009514 | uPc
kernel: iwlagn 0000:03:00.0: 0x00009496 | branchlink1
kernel: iwlagn 0000:03:00.0: 0x00009496 | branchlink2
kernel: iwlagn 0000:03:00.0: 0x0000D1F2 | interruptlink1
kernel: iwlagn 0000:03:00.0: 0x00000000 | interruptlink2
kernel: iwlagn 0000:03:00.0: 0x01008035 | data1
kernel: iwlagn 0000:03:00.0: 0x0000C90F | data2
kernel: iwlagn 0000:03:00.0: 0x000005A7 | line
kernel: iwlagn 0000:03:00.0: 0x5080B520 | beacon time
kernel: iwlagn 0000:03:00.0: 0xCC515AE0 | tsf low
kernel: iwlagn 0000:03:00.0: 0x00000003 | tsf hi
kernel: iwlagn 0000:03:00.0: 0x00000000 | time gp1
kernel: iwlagn 0000:03:00.0: 0x29703BF0 | time gp2
kernel: iwlagn 0000:03:00.0: 0x00000000 | time gp3
kernel: iwlagn 0000:03:00.0: 0x000111A8 | uCode version
kernel: iwlagn 0000:03:00.0: 0x000000B0 | hw version
kernel: iwlagn 0000:03:00.0: 0x00480303 | board version
kernel: iwlagn 0000:03:00.0: 0x09E8004E | hcmd
kernel: iwlagn 0000:03:00.0: CSR values:
kernel: iwlagn 0000:03:00.0: (2nd byte of CSR_INT_COALESCING is CSR_INT_PERIODIC_REG)
kernel: iwlagn 0000:03:00.0: CSR_HW_IF_CONFIG_REG: 0X00480303
kernel: iwlagn 0000:03:00.0: CSR_INT_COALESCING: 0X0000ff40
kernel: iwlagn 0000:03:00.0: CSR_INT: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_INT_MASK: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_FH_INT_STATUS: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_GPIO_IN: 0X00000030
kernel: iwlagn 0000:03:00.0: CSR_RESET: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_GP_CNTRL: 0X080403c5
kernel: iwlagn 0000:03:00.0: CSR_HW_REV: 0X000000b0
kernel: iwlagn 0000:03:00.0: CSR_EEPROM_REG: 0X07d60ffd
kernel: iwlagn 0000:03:00.0: CSR_EEPROM_GP: 0X90000001
kernel: iwlagn 0000:03:00.0: CSR_OTP_GP_REG: 0X00030001
kernel: iwlagn 0000:03:00.0: CSR_GIO_REG: 0X00080044
kernel: iwlagn 0000:03:00.0: CSR_GP_UCODE_REG: 0X000093bb
kernel: iwlagn 0000:03:00.0: CSR_GP_DRIVER_REG: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_UCODE_DRV_GP1: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_UCODE_DRV_GP2: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_LED_REG: 0X00000078
kernel: iwlagn 0000:03:00.0: CSR_DRAM_INT_TBL_REG: 0X88214dd2
kernel: iwlagn 0000:03:00.0: CSR_GIO_CHICKEN_BITS: 0X27800200
kernel: iwlagn 0000:03:00.0: CSR_ANA_PLL_CFG: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_HW_REV_WA_REG: 0X0001001a
kernel: iwlagn 0000:03:00.0: CSR_DBG_HPET_MEM_REG: 0Xffff0010
kernel: iwlagn 0000:03:00.0: FH register values:
kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_STTS_WPTR_REG: 0X21316d00
kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_RBDCB_BASE_REG: 0X021479c0
kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_WPTR: 0X00000060
kernel: iwlagn 0000:03:00.0: FH_MEM_RCSR_CHNL0_CONFIG_REG: 0X80819104
kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_SHARED_CTRL_REG: 0X000000fc
kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_RX_STATUS_REG: 0X07030000
kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV: 0X00000000
kernel: iwlagn 0000:03:00.0: FH_TSSR_TX_STATUS_REG: 0X07ff0001
kernel: iwlagn 0000:03:00.0: FH_TSSR_TX_ERROR_REG: 0X00000000
kernel: iwlagn 0000:03:00.0: Start IWL Event Log Dump: display last 20 entries
kernel: ------------[ cut here ]------------
WARNING: at net/mac80211/util.c:1208 ieee80211_reconfig+0x1f1/0x407()
kernel: Hardware name: 4290W4H
kernel: Pid: 1896, comm: kworker/0:0 Not tainted 3.1.0 #2
kernel: Call Trace:
kernel: [<
ffffffff81036558>] ? warn_slowpath_common+0x73/0x87
kernel: [<
ffffffff813b8966>] ? ieee80211_reconfig+0x1f1/0x407
kernel: [<
ffffffff8139e8dc>] ? ieee80211_recalc_smps_work+0x32/0x32
kernel: [<
ffffffff8139e95a>] ? ieee80211_restart_work+0x7e/0x87
kernel: [<
ffffffff810472fa>] ? process_one_work+0x1c8/0x2e3
kernel: [<
ffffffff810480c9>] ? worker_thread+0x17a/0x23a
kernel: [<
ffffffff81047f4f>] ? manage_workers.clone.18+0x15b/0x15b
kernel: [<
ffffffff81047f4f>] ? manage_workers.clone.18+0x15b/0x15b
kernel: [<
ffffffff8104ba97>] ? kthread+0x7a/0x82
kernel: [<
ffffffff813d21b4>] ? kernel_thread_helper+0x4/0x10
kernel: [<
ffffffff8104ba1d>] ? kthread_flush_work_fn+0x11/0x11
kernel: [<
ffffffff813d21b0>] ? gs_change+0xb/0xb
Cc: <stable@kernel.org> 3.1+
Reported-by: Udo Steinberg <udo@hypervisor.org>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 2 Dec 2011 16:19:17 +0000 (08:19 -0800)]
iwlagn: fix HW crypto for TX-only keys
Group keys in IBSS or AP mode are not programmed
into the device since we give the key to it with
every TX packet. However, we do need mac80211 to
create the MMIC & PN in all cases. Move the code
around to set the key flags all the time. We set
them even when the key is removed again but that
is obviously harmless.
Cc: stable@vger.kernel.org
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don Fry [Tue, 29 Nov 2011 00:13:19 +0000 (16:13 -0800)]
iwlwifi: move ucode notification from iwl_priv to iwl_shared
Move the notification structures for ucode operations from the
iwl_priv structure to the iwl_shared structure, with associated
code changes.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Don Fry [Tue, 29 Nov 2011 01:05:01 +0000 (17:05 -0800)]
iwlwifi: move ucode_type from iwl_priv to iwl_shared
Move the ucode_type variable from the iwl_priv to the iwl_shared
structure with associated code changes.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Don Fry [Mon, 28 Nov 2011 22:35:14 +0000 (14:35 -0800)]
iwlwifi: replace iwl_priv reference with iwl_trans for ucode.
Replace the references to the iwl_priv structure with the iwl_trans
structure as the priv structure is never referenced other than to
access the trans structure. Rename from iwlagn to iwl.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Don Fry [Mon, 28 Nov 2011 22:34:13 +0000 (14:34 -0800)]
iwlwifi: rename iwl-agn-ucode as iwl-ucode
iwl-agn-ucode is generic ucode operations, not limited just to iwlagn.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Fri, 25 Nov 2011 19:29:16 +0000 (11:29 -0800)]
iwlwifi: Rename file name from iwl-sv-open.c to iwl-testmode.c
The file dealing with all the operations through testmode, rename it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Hsu, Kenny [Fri, 25 Nov 2011 06:26:53 +0000 (22:26 -0800)]
iwlwifi: add WOWLAN uCode loading support by testmode
Create new tm command for WOWLAN uCode loading to support
further debugging function in userspace.
- IWL_TM_CMD_APP2DEV_LOAD_WOWLAN_FW
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Fri, 25 Nov 2011 12:57:49 +0000 (04:57 -0800)]
iwlagn: make debug levels more readable
Using the actual shifted constants here allows
one to read and or them more easily.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Fri, 25 Nov 2011 12:57:48 +0000 (04:57 -0800)]
iwlagn: remove MACDUMP debug
This is only used for TX debugging where there
already is more debugging and tracing is more
useful anyway, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Fri, 25 Nov 2011 12:57:47 +0000 (04:57 -0800)]
iwlagn: remove HC_DUMP debug
This debug level is unused, remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Fri, 25 Nov 2011 12:57:46 +0000 (04:57 -0800)]
iwlagn: remove TX_REPLY_LIMIT debug
This macro is unused right now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Fri, 25 Nov 2011 11:20:09 +0000 (03:20 -0800)]
iwlagn: fix HW crypto for TX-only keys
Group keys in IBSS or AP mode are not programmed
into the device since we give the key to it with
every TX packet. However, we do need mac80211 to
create the MMIC & PN in all cases. Move the code
around to set the key flags all the time. We set
them even when the key is removed again but that
is obviously harmless.
Cc: stable@vger.kernel.org
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Wed, 23 Nov 2011 15:08:22 +0000 (07:08 -0800)]
iwlwifi: declare static for iwl_sram_cleanup function
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Hsu, Kenny [Wed, 23 Nov 2011 07:05:02 +0000 (23:05 -0800)]
iwlwifi: add generic chunk size of tm dumpit packet
Use generic chunk size of dumpit packet for
all necessary testmode commands instead of
add declaration individually.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Kenny Hsu [Wed, 23 Nov 2011 14:57:22 +0000 (06:57 -0800)]
iwlwifi: add range checking in tm sram read command
The size of sram may alter according to ucode type.
Retrieve the maximum sram size by current ucode
type for range checking to prevent wrong data access.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Hsu, Kenny [Wed, 23 Nov 2011 07:03:39 +0000 (23:03 -0800)]
iwlwifi: add tm commands for sram reading by dumpit
Create new testmode commands and attributes to suppot
sram data reading. Because the amount of sram data
may exceed single skb packet size. Using the nl80211
dump it funtion to deliver sram data to userspace.
- IWL_TM_CMD_APP2DEV_READ_SRAM
- IWL_TM_CMD_APP2DEV_DUMP_SRAM
- IWL_TM_ATTR_SRAM_ADDR
- IWL_TM_ATTR_SRAM_SIZE
- IWL_TM_ATTR_SRAM_DUMP
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Wed, 23 Nov 2011 00:23:35 +0000 (16:23 -0800)]
iwlwifi: do not re-configure HT40 after associated
The ht40 setting should not change after association unless channel switch
This fix a problem we are seeing which cause uCode assert because driver
sending invalid information and make uCode confuse
Here is the firmware assert message:
kernel: iwlagn 0000:03:00.0: Microcode SW error detected. Restarting 0x82000000.
kernel: iwlagn 0000:03:00.0: Loaded firmware version: 17.168.5.3 build 42301
kernel: iwlagn 0000:03:00.0: Start IWL Error Log Dump:
kernel: iwlagn 0000:03:00.0: Status: 0x000512E4, count: 6
kernel: iwlagn 0000:03:00.0: 0x00002078 | ADVANCED_SYSASSERT
kernel: iwlagn 0000:03:00.0: 0x00009514 | uPc
kernel: iwlagn 0000:03:00.0: 0x00009496 | branchlink1
kernel: iwlagn 0000:03:00.0: 0x00009496 | branchlink2
kernel: iwlagn 0000:03:00.0: 0x0000D1F2 | interruptlink1
kernel: iwlagn 0000:03:00.0: 0x00000000 | interruptlink2
kernel: iwlagn 0000:03:00.0: 0x01008035 | data1
kernel: iwlagn 0000:03:00.0: 0x0000C90F | data2
kernel: iwlagn 0000:03:00.0: 0x000005A7 | line
kernel: iwlagn 0000:03:00.0: 0x5080B520 | beacon time
kernel: iwlagn 0000:03:00.0: 0xCC515AE0 | tsf low
kernel: iwlagn 0000:03:00.0: 0x00000003 | tsf hi
kernel: iwlagn 0000:03:00.0: 0x00000000 | time gp1
kernel: iwlagn 0000:03:00.0: 0x29703BF0 | time gp2
kernel: iwlagn 0000:03:00.0: 0x00000000 | time gp3
kernel: iwlagn 0000:03:00.0: 0x000111A8 | uCode version
kernel: iwlagn 0000:03:00.0: 0x000000B0 | hw version
kernel: iwlagn 0000:03:00.0: 0x00480303 | board version
kernel: iwlagn 0000:03:00.0: 0x09E8004E | hcmd
kernel: iwlagn 0000:03:00.0: CSR values:
kernel: iwlagn 0000:03:00.0: (2nd byte of CSR_INT_COALESCING is CSR_INT_PERIODIC_REG)
kernel: iwlagn 0000:03:00.0: CSR_HW_IF_CONFIG_REG: 0X00480303
kernel: iwlagn 0000:03:00.0: CSR_INT_COALESCING: 0X0000ff40
kernel: iwlagn 0000:03:00.0: CSR_INT: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_INT_MASK: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_FH_INT_STATUS: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_GPIO_IN: 0X00000030
kernel: iwlagn 0000:03:00.0: CSR_RESET: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_GP_CNTRL: 0X080403c5
kernel: iwlagn 0000:03:00.0: CSR_HW_REV: 0X000000b0
kernel: iwlagn 0000:03:00.0: CSR_EEPROM_REG: 0X07d60ffd
kernel: iwlagn 0000:03:00.0: CSR_EEPROM_GP: 0X90000001
kernel: iwlagn 0000:03:00.0: CSR_OTP_GP_REG: 0X00030001
kernel: iwlagn 0000:03:00.0: CSR_GIO_REG: 0X00080044
kernel: iwlagn 0000:03:00.0: CSR_GP_UCODE_REG: 0X000093bb
kernel: iwlagn 0000:03:00.0: CSR_GP_DRIVER_REG: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_UCODE_DRV_GP1: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_UCODE_DRV_GP2: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_LED_REG: 0X00000078
kernel: iwlagn 0000:03:00.0: CSR_DRAM_INT_TBL_REG: 0X88214dd2
kernel: iwlagn 0000:03:00.0: CSR_GIO_CHICKEN_BITS: 0X27800200
kernel: iwlagn 0000:03:00.0: CSR_ANA_PLL_CFG: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_HW_REV_WA_REG: 0X0001001a
kernel: iwlagn 0000:03:00.0: CSR_DBG_HPET_MEM_REG: 0Xffff0010
kernel: iwlagn 0000:03:00.0: FH register values:
kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_STTS_WPTR_REG: 0X21316d00
kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_RBDCB_BASE_REG: 0X021479c0
kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_WPTR: 0X00000060
kernel: iwlagn 0000:03:00.0: FH_MEM_RCSR_CHNL0_CONFIG_REG: 0X80819104
kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_SHARED_CTRL_REG: 0X000000fc
kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_RX_STATUS_REG: 0X07030000
kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV: 0X00000000
kernel: iwlagn 0000:03:00.0: FH_TSSR_TX_STATUS_REG: 0X07ff0001
kernel: iwlagn 0000:03:00.0: FH_TSSR_TX_ERROR_REG: 0X00000000
kernel: iwlagn 0000:03:00.0: Start IWL Event Log Dump: display last 20 entries
kernel: ------------[ cut here ]------------
WARNING: at net/mac80211/util.c:1208 ieee80211_reconfig+0x1f1/0x407()
kernel: Hardware name: 4290W4H
kernel: Pid: 1896, comm: kworker/0:0 Not tainted 3.1.0 #2
kernel: Call Trace:
kernel: [<
ffffffff81036558>] ? warn_slowpath_common+0x73/0x87
kernel: [<
ffffffff813b8966>] ? ieee80211_reconfig+0x1f1/0x407
kernel: [<
ffffffff8139e8dc>] ? ieee80211_recalc_smps_work+0x32/0x32
kernel: [<
ffffffff8139e95a>] ? ieee80211_restart_work+0x7e/0x87
kernel: [<
ffffffff810472fa>] ? process_one_work+0x1c8/0x2e3
kernel: [<
ffffffff810480c9>] ? worker_thread+0x17a/0x23a
kernel: [<
ffffffff81047f4f>] ? manage_workers.clone.18+0x15b/0x15b
kernel: [<
ffffffff81047f4f>] ? manage_workers.clone.18+0x15b/0x15b
kernel: [<
ffffffff8104ba97>] ? kthread+0x7a/0x82
kernel: [<
ffffffff813d21b4>] ? kernel_thread_helper+0x4/0x10
kernel: [<
ffffffff8104ba1d>] ? kthread_flush_work_fn+0x11/0x11
kernel: [<
ffffffff813d21b0>] ? gs_change+0xb/0xb
Cc: <stable@kernel.org> 3.1+
Reported-by: Udo Steinberg <udo@hypervisor.org>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Fri, 2 Dec 2011 16:20:01 +0000 (08:20 -0800)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next into wireless-next
Andrei Emeltchenko [Thu, 1 Dec 2011 12:42:08 +0000 (14:42 +0200)]
Bluetooth: remove old code
Remove old code not touched for several years.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andre Guedes [Fri, 2 Dec 2011 12:13:31 +0000 (21:13 +0900)]
Bluetooth: LE Set Scan Parameter Command
This patch adds the parameter struct and the command complete event
handler to the LE Set Scan Parameter HCI command.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andre Guedes [Fri, 25 Nov 2011 23:53:38 +0000 (20:53 -0300)]
Bluetooth: Add dev_flags to struct hci_dev
This patch adds the dev_flags field to struct hci_dev. This new
flags variable should be used to define flags related to BR/EDR
and/or LE controller itself. It should be used to define flags
which represents states from the controller. The dev_flags is
cleared in case the controller sends a Reset Command Complete
Event to the host.
Also, this patch adds the HCI_LE_SCAN flag which was created to
track if the controller is performing LE scan or not. The flag
is set/cleared when the controller starts/stops scanning.
This is an initial effort to stop using hdev->flags to define
internal flags since it is exported to userspace by an ioctl.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andrei Emeltchenko [Thu, 24 Nov 2011 12:52:02 +0000 (14:52 +0200)]
Bluetooth: Add HCI Read Flow Control Mode function
Upstream Code Aurora function with minor trivial fixes.
Origin: git://codeaurora.org/kernel/msm.git
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
John W. Linville [Thu, 1 Dec 2011 15:44:17 +0000 (10:44 -0500)]
Revert "mac80211: clear sta.drv_priv on reconfiguration"
This reverts commit
f785d83a19bca326f79d127a413e35769afc0105.
This was provoking WARNINGs from the iwlegacy drivers.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Tue, 8 Nov 2011 14:07:52 +0000 (16:07 +0200)]
wl12xx: don't explicitly check for unjoined ibss
After the ibss carrier issue was fixed, we can revert
the following patch:
commit
48309fd477ef867babb6819f67fe082c133a5fa9
Author: Shahar Lev <shahar@wizery.com>
Date: Fri Oct 7 18:17:25 2011 +0200
wl12xx: remove warning message during IBSS Tx
mac80211 sets the carrier on an IBSS interface even when no network is
joined. Ignore garbage frames transmitted on a disconnected IBSS
interface without printing warnings.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Arik Nemtsov [Sun, 23 Oct 2011 06:21:54 +0000 (08:21 +0200)]
wl12xx: leave IV calculation to HW for CCMP
Use an appropriate mac80211 flags in CCMP keys to indicate we are
calculating the CCMP IV in HW, but require room for the IV to be reserved
in the skb. The space is reserved by mac80211.
depends on "mac80211: support adding IV-room in the skb for CCMP keys".
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Pontus Fuchs [Wed, 30 Nov 2011 14:35:09 +0000 (15:35 +0100)]
wl12xx: Print nvs/fw file name if loading fails.
Print the name of nvs/fw if request_firmware fails. This will make
troubleshooting a bit easier.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Arik Nemtsov [Tue, 22 Nov 2011 17:52:59 +0000 (19:52 +0200)]
wl12xx: avoid bail out when probe-resp is not set by mac80211
During reconfig we can get the BSS_CHANGED_AP_PROBE_RESP indication
even if a probe-resp has not been set in the first place. Therefore
ignore the error when not getting a probe-resp from mac80211. Resort to
the legacy probe-resp in this case.
Also take this opportunity to add a vif argument to the set_probe_resp
function.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Wed, 9 Nov 2011 11:12:45 +0000 (13:12 +0200)]
wl12xx: init CMD_TEMPL_KLV to sizeof(ieee80211_qos_hdr)
The keep alive template should have a max size of
sizeof(struct ieee80211_qos_hdr).
Additionally, Remove the redundant wl12xx_qos_null_data_template
struct.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Arik Nemtsov [Tue, 8 Nov 2011 16:46:55 +0000 (18:46 +0200)]
wl12xx: indicate probe-resp offloading support
The wl12xx driver supports probe-response offloading, and the WPS, WPS2
and P2P special cases as well.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Arik Nemtsov [Tue, 8 Nov 2011 16:46:54 +0000 (18:46 +0200)]
wl12xx: configure probe-resp template according to notification
When operating in AP-mode, replace our probe-response template when a
notification is recieved from mac80211. We preserve the "legacy" way of
configuring a probe-response according to beacon for IBSS mode and for
versions of hostapd that do not support this feature.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Pontus Fuchs [Tue, 18 Oct 2011 07:23:42 +0000 (09:23 +0200)]
wl12xx: Check buffer bound when processing nvs data
An nvs with malformed contents could cause the processing of the
calibration data to read beyond the end of the buffer. Prevent this
from happening by adding bound checking.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Cc: stable@kernel.org
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Pontus Fuchs [Tue, 18 Oct 2011 07:23:41 +0000 (09:23 +0200)]
wl12xx: Validate FEM index from ini file and FW
Check for out of bound FEM index to prevent reading beyond ini
memory end.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Cc: stable@kernel.org
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Brian Gix [Wed, 23 Nov 2011 16:28:36 +0000 (08:28 -0800)]
Bluetooth: Centralize SMP pairing failure handling
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Brian Gix [Wed, 23 Nov 2011 16:28:35 +0000 (08:28 -0800)]
Bluetooth: Cleanup blkcipher on SMP termination
The blkcipher must be freed to avoid memory leak.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Brian Gix [Wed, 23 Nov 2011 16:28:34 +0000 (08:28 -0800)]
Bluetooth: Add HCI User Passkey Req Evt handling
Some MITM scenarios require handling of the User Passkey Request event,
by querying the user, and passing the response back.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Brian Gix [Wed, 23 Nov 2011 16:28:33 +0000 (08:28 -0800)]
Bluetooth: Add User Passkey Response handling
For some MITM protection pairing scenarios, the user is
required to enter or accept a 6 digit passkey.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Luciano Coelho [Thu, 1 Dec 2011 10:14:48 +0000 (12:14 +0200)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next into wl12xx-next
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 15:40:52 +0000 (21:10 +0530)]
ath9k_hw: add default chainmask for AR9462
the default tx/rx chainmask for AR9462 is 0x3.
this patch helps to assign 0x3 rather than 0x7 for
AR9462 with the help of fix_chainmask module if something
goes wrong in reading tx/rx chain mask from OTP/EEPROM
card(though its very unlikely)
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / profile / common / kernel-common.git / log