rtc: omap: fix clock-source configuration

This series fixes a few issues with the omap rtc-driver, cleans up a
bit, adds device abstraction, and finally adds support for the PMIC
control feature found in some revisions of this RTC IP block.

Ultimately, this allows for powering off the Beaglebone and waking it up
again on RTC alarms.

This patch (of 20):

Make sure not to reset the clock-source configuration when enabling the
32kHz clock mux.

Until the clock source can be configured through device tree we must not
overwrite settings made by the bootloader (e.g.  clock-source
selection).

Fixes: cd914bba03d8 ("drivers/rtc/rtc-omap.c: add support for enabling 32khz clock")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/interface.c: check the validation of rtc_time in __rtc_read_time

Some rtc devices always return '0' when rtc_class_ops.read_time is
called.  So if rtc_time isn't verified in callback, rtc interface cannot
know whether rtc_time is valid.

Check rtc_time by using 'rtc_valid_tm' in '__rtc_read_time'.  And add
the message for debugging.

Signed-off-by: Hyogi Gim <hyogi.gim@lge.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-sirfsoc.c: move hardware initilization earlier in probe

Move rtc register to be later than hardware initialization.  The reason
is that devm_rtc_device_register() will do read_time() which is a
callback accessing hardware.  This sometimes causes a hang in the
hardware related callback.

Signed-off-by: Guo Zeng <guo.zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ncpfs: return proper error from NCP_IOC_SETROOT ioctl

If some error happens in NCP_IOC_SETROOT ioctl, the appropriate error
return value is then (in most cases) just overwritten before we return.
This can result in reporting success to userspace although error happened.

This bug was introduced by commit 2e54eb96e2c8 ("BKL: Remove BKL from
ncpfs").  Propagate the errors correctly.

Coverity id: 1226925.

Fixes: 2e54eb96e2c80 ("BKL: Remove BKL from ncpfs")
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

init: allow CONFIG_INIT_FALLBACK=n to disable defaults if init= fails

If a user puts init=/whatever on the command line and /whatever can't be
run, then the kernel will try a few default options before giving up.  If
init=/whatever came from a bootloader prompt, then this is unexpected but
probably harmless.  On the other hand, if it comes from a script (e.g.  a
tool like virtme or perhaps a future kselftest script), then the fallbacks
are likely to exist, but they'll do the wrong thing.  For example, they
might unexpectedly invoke systemd.

This adds a config option CONFIG_INIT_FALLBACK.  If unset, then a failure
to run the specified init= process be fatal.

The tentative plan is to remove CONFIG_INIT_FALLBACK for 3.20.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Rob Landley <rob@landley.net>
Cc: Chuck Ebbert <cebbert.lkml@gmail.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Shuah Khan <shuah.kh@samsung.com>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/binfmt_elf.c: fix internal inconsistency relating to vma dump size

vma_dump_size() has been used several times on actual dumper and it is
supposed to return the same value for the same vma.  But vma_dump_size()
could return different values for same vma.

The known problem case is concurrent shared memory removal.  If a vma is
used for a shared memory and that shared memory is removed between
writing program header and dumping vma memory, this will result in a
dump file which is internally consistent.

To fix the problem, we set baseline to get dump size and store the size
into vma_filesz and always use the same vma dump size which is stored in
vma_filsz.  The consistnecy with reality is not actually guranteed, but
it's tolerable since that is fully consistent with base line.

Signed-off-by: Jungseung Lee <js07.lee@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/binfmt_misc.c: use GFP_KERNEL instead of GFP_USER

GFP_USER means "honour cpuset nodes-allowed beancounting".  These are
regular old kernel objects and there seems no reason to give them this
treatment.

Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

binfmt_misc: clean up code style a bit

Clean up various coding style issues that checkpatch complains about.
No functional changes here.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

binfmt_misc: add comments & debug logs

When trying to develop a custom format handler, the errors returned all
effectively get bucketed as EINVAL with no kernel messages.  The other
errors (ENOMEM/EFAULT) are internal/obvious and basic.  Thus any time a
bad handler is rejected, the developer has to walk the dense code and
try to guess where it went wrong.  Needing to dive into kernel code is
itself a fairly high barrier for a lot of people.

To improve this situation, let's deploy extensive pr_debug markers at
logical parse points, and add comments to the dense parsing logic.  It
let's you see exactly where the parsing aborts, the string the kernel
received (useful when dealing with shell code), how it translated the
buffers to binary data, and how it will apply the mask at runtime.

Some example output:
  $ echo ':qemu-foo:M::\x7fELF\xAD\xAD\x01\x00:\xff\xff\xff\xff\xff\x00\xff\x00:/usr/bin/qemu-foo:POC' > register
  $ dmesg
  binfmt_misc: register: received 92 bytes
  binfmt_misc: register: delim: 0x3a {:}
  binfmt_misc: register: name: {qemu-foo}
  binfmt_misc: register: type: M (magic)
  binfmt_misc: register: offset: 0x0
  binfmt_misc: register: magic[raw]: 5c 78 37 66 45 4c 46 5c 78 41 44 5c 78 41 44 5c  \x7fELF\xAD\xAD\
  binfmt_misc: register: magic[raw]: 78 30 31 5c 78 30 30 00                          x01\x00.
  binfmt_misc: register:  mask[raw]: 5c 78 66 66 5c 78 66 66 5c 78 66 66 5c 78 66 66  \xff\xff\xff\xff
  binfmt_misc: register:  mask[raw]: 5c 78 66 66 5c 78 30 30 5c 78 66 66 5c 78 30 30  \xff\x00\xff\x00
  binfmt_misc: register:  mask[raw]: 00                                               .
  binfmt_misc: register: magic/mask length: 8
  binfmt_misc: register: magic[decoded]: 7f 45 4c 46 ad ad 01 00                          .ELF....
  binfmt_misc: register:  mask[decoded]: ff ff ff ff ff 00 ff 00                          ........
  binfmt_misc: register:  magic[masked]: 7f 45 4c 46 ad 00 01 00                          .ELF....
  binfmt_misc: register: interpreter: {/usr/bin/qemu-foo}
  binfmt_misc: register: flag: P (preserve argv0)
  binfmt_misc: register: flag: O (open binary)
  binfmt_misc: register: flag: C (preserve creds)

The [raw] lines show us exactly what was received from userspace.  The
lines after that show us how the kernel has decoded things.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: add ability to --fix (coalesce) string fragments on multiple lines

Add --fix option to coalesce string fragments.

This does not coalesce string fragments that have newline terminations or
are otherwise exempted.

Other miscellanea:

o move all the string tests together.
o fix get_quoted_string function for tab characters
o fix concatination typo

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: add --strict "pointer comparison to NULL" test

It seems there are more and more uses of "if (!ptr)" in preference to "if
(ptr == NULL)" so add a --strict test to emit a message when using the
latter form.

This also finds (ptr != NULL).

Fix it too if desired.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: add test for consecutive string fragments

Emit a warning when single line string coalescing occurs.

Code that uses compiler string concatenation on a single line like:

    printk("foo" "bar");

is generally better to read concatenated like:

    printk("foobar");

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: add --strict preference for #defines using BIT(foo)

Using BIT(foo) and BIT_ULL(bar) is more common now.  Suggest using these
macros over #defines with 1<<value.

Add a --fix option too.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: David Miller <davem@davemloft.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: allow certain SI units with three characters

Checkpatch flags CamelCase identifiers in strict mode, but it has a
feature to ignore parts with only two characters to allow for SI units
like mV or uA.  Unfortunately, not all SI units fit in two characters, and
not all are lower case followed by upper case.

This patch adds hardcoded detection for frequency and 1024-based size
units (Hz/KHz/MHz/GHz/THz and KiB/MiB/GiB/TiB), since allowing any three
character combinations might be too lenient.  The list can later be
expanded as needed.

Signed-off-by: Julius Werner <jwerner@chromium.org>
Acked-by: Joe Perches <joe@perches.com>
Cc: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: Add --strict test for function pointer calling style

Peter Hurley wrote:

The use of older function ptr calling style, (*fn)(), makes static
analysis more error-prone; replace with modern fn() style.

So make checkpatch emit a --strict test for that condition.

Update the unnecessary parentheses test for dereferencing
objects at the same time and create a $fix mechanism too.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: reduce MAINTAINERS update message frequency

When files are being added/moved/deleted and a patch contains an update to
the MAINTAINERS file, assume it's to update the MAINTAINERS file correctly
and do not emit the "does MAINTAINERS need updating?" message.

Reported by many people.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: try to avoid mask and shift errors

Shift has a higher precedence that mask so warn when a mask then shift
operation is done without parentheses around the mask.

This test works well for a right shift, but the left shift is pretty
commonly done correctly so only warn on the right shift.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: fix use via symlink, make missing spelling file non-fatal

Commit 66b47b4a9dad ("checkpatch: look for common misspellings") made it
difficult to use checkpatch via a symlink.

Fix that and make a missing spelling.txt file non-fatal.  Emit a warning
when the spelling.txt file can not be opened.

Reference: http://xkcd.com/1172/

Signed-off-by: Joe Perches <joe@perches.com>
Reported-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: improve warning message for "needless if" case

Add an 'and' to the sentence so that it looks better:

  WARNING: debugfs_remove(NULL) is safe and this check is probably not required

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: improve test for no space after cast

sizeof(foo) is not a cast, allow a space after it.

Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: add error on use of attribute((weak)) or __weak declarations

Using weak declarations can have unintended link defects.  The __weak on
the declaration causes non-weak definitions to become weak.

Emit an error on its use.

Signed-off-by: Joe Perches <joe@perches.com>
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: add an error test for no space before comma

Using code like:

    int foo , bar;

is not preferred to:

    int foo, bar;

so emit an error on this style.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lib/lcm.c: lcm(n,0)=lcm(0,n) is 0, not n

Return the mathematically correct answer when an argument is 0.

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lib/lcm.c: ensure correct result whenever it fits

Ensure that lcm(a,b) returns the mathematically correct result, provided
it fits in an unsigned long.  The current version returns garbage if a*b
overflows, even if the final result would fit.

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MAINTAINERS: update ivtv mailing lists as subscriber-only

Mark these as subscriber-only mailing lists.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

printk: drop logbuf_cpu volatile qualifier

Pranith Kumar posted a patch in which removed the "volatile"
qualifier for the "logbuf_cpu" variable in vprintk_emit().
    https://lkml.org/lkml/2014/11/13/894
In his patch, he used ACCESS_ONCE() for all references to
that symbol to provide whatever protection was intended.

There was some discussion that followed, and in the end Steven Rostedt
concluded that not only was "volatile" not needed, neither was it
required to use ACCESS_ONCE().  I offered an elaborate description that
concluded Steven was right, and Pranith asked me to submit an
alternative patch.  And this is it.

The basic reason "volatile" is not needed is that "logbuf_cpu" has
static storage duration, and vprintk_emit() is an exported
interface.  This means that the value of logbuf_cpu must be read
from memory the first time it is used in a particular call of
vprintk_emit().  The variable's value is read only once in that
function, when it's read it'll be the copy from memory (or cache).

In addition, the value of "logbuf_cpu" is only ever written under
protection of a spinlock.  So the value that is read is the "real"
value (and not an out-of-date cached one).  If its value is not
UINT_MAX, it is the current CPU's processor id, and it will have
been last written by the running CPU.

Signed-off-by: Alex Elder <elder@linaro.org>
Reported-by: Pranith Kumar <bobby.prani@gmail.com>
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Petr Mladek <pmladek@suse.cz>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

printk: add and use LOGLEVEL_<level> defines for KERN_<LEVEL> equivalents

Use #defines instead of magic values.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jason Baron <jbaron@akamai.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tile: use pr_warn instead of pr_warning

Use the more common pr_warn.

Coalesce formats, realign arguments.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tile: neaten early_printk uses

Coalesce the formats and align arguments.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

printk: remove used-once early_vprintk

Eliminate the unlikely possibility of message interleaving for
early_printk/early_vprintk use.

early_vprintk can be done via the %pV extension so remove this
unnecessary function and change early_printk to have the equivalent
vprintk code.

All uses of early_printk already end with a newline so also remove the
unnecessary newline from the early_printk function.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel: add panic_on_warn

There have been several times where I have had to rebuild a kernel to
cause a panic when hitting a WARN() in the code in order to get a crash
dump from a system.  Sometimes this is easy to do, other times (such as
in the case of a remote admin) it is not trivial to send new images to
the user.

A much easier method would be a switch to change the WARN() over to a
panic.  This makes debugging easier in that I can now test the actual
image the WARN() was seen on and I do not have to engage in remote
debugging.

This patch adds a panic_on_warn kernel parameter and
/proc/sys/kernel/panic_on_warn calls panic() in the
warn_slowpath_common() path.  The function will still print out the
location of the warning.

An example of the panic_on_warn output:

The first line below is from the WARN_ON() to output the WARN_ON()'s
location.  After that the panic() output is displayed.

    WARNING: CPU: 30 PID: 11698 at /home/prarit/dummy_module/dummy-module.c:25 init_dummy+0x1f/0x30 [dummy_module]()
    Kernel panic - not syncing: panic_on_warn set ...

    CPU: 30 PID: 11698 Comm: insmod Tainted: G        W  OE  3.17.0+ #57
    Hardware name: Intel Corporation S2600CP/S2600CP, BIOS RMLSDP.86I.00.29.D696.1311111329 11/11/2013
     0000000000000000 000000008e3f87df ffff88080f093c38 ffffffff81665190
     0000000000000000 ffffffff818aea3d ffff88080f093cb8 ffffffff8165e2ec
     ffffffff00000008 ffff88080f093cc8 ffff88080f093c68 000000008e3f87df
    Call Trace:
     [<ffffffff81665190>] dump_stack+0x46/0x58
     [<ffffffff8165e2ec>] panic+0xd0/0x204
     [<ffffffffa038e05f>] ? init_dummy+0x1f/0x30 [dummy_module]
     [<ffffffff81076b90>] warn_slowpath_common+0xd0/0xd0
     [<ffffffffa038e040>] ? dummy_greetings+0x40/0x40 [dummy_module]
     [<ffffffff81076c8a>] warn_slowpath_null+0x1a/0x20
     [<ffffffffa038e05f>] init_dummy+0x1f/0x30 [dummy_module]
     [<ffffffff81002144>] do_one_initcall+0xd4/0x210
     [<ffffffff811b52c2>] ? __vunmap+0xc2/0x110
     [<ffffffff810f8889>] load_module+0x16a9/0x1b30
     [<ffffffff810f3d30>] ? store_uevent+0x70/0x70
     [<ffffffff810f49b9>] ? copy_module_from_fd.isra.44+0x129/0x180
     [<ffffffff810f8ec6>] SyS_finit_module+0xa6/0xd0
     [<ffffffff8166cf29>] system_call_fastpath+0x12/0x17

Successfully tested by me.

hpa said: There is another very valid use for this: many operators would
rather a machine shuts down than being potentially compromised either
functionally or security-wise.

Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

include/linux/file.h: remove get_unused_fd() macro

Macro get_unused_fd() is used to allocate a file descriptor with default
flags.  Those default flags (0) don't enable close-on-exec.

This can be seen as an unsafe default: in most case close-on-exec should
be enabled to not leak file descriptor across exec().

It would be better to have a "safer" default set of flags, eg.  O_CLOEXEC
must be used to enable close-on-exec.

Instead this patch removes get_unused_fd() so that out of tree modules
won't be affect by a runtime behavor change which might introduce other
kind of bugs: it's better to catch the change at build time, making it
easier to fix.

Removing the macro will also promote use of get_unused_fd_flags() (or
anon_inode_getfd()) with flags provided by userspace.  Or, if flags cannot
be given by userspace, with flags set to O_CLOEXEC by default.

Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/file.c: replace get_unused_fd() with get_unused_fd_flags(0)

This patch replaces calls to get_unused_fd() with equivalent call to
get_unused_fd_flags(0) to preserve current behavor for existing code.

In a further patch, get_unused_fd() will be removed so that new code
start using get_unused_fd_flags(), with the hope O_CLOEXEC could be
used, either by default or choosen by userspace.

Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

binfmt_misc: replace get_unused_fd() with get_unused_fd_flags(0)

This patch replaces calls to get_unused_fd() with equivalent call to
get_unused_fd_flags(0) to preserve current behavor for existing code.

In a further patch, get_unused_fd() will be removed so that new code start
using get_unused_fd_flags(), with the hope O_CLOEXEC could be used, either
by default or choosen by userspace.

Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ppc/cell: replace get_unused_fd() with get_unused_fd_flags(0)

This patch replaces calls to get_unused_fd() with equivalent call to
get_unused_fd_flags(0) to preserve current behavor for existing code.

In a further patch, get_unused_fd() will be removed so that new code start
using get_unused_fd_flags(), with the hope O_CLOEXEC could be used, either
by default or choosen by userspace.

Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ia64: replace get_unused_fd() with get_unused_fd_flags(0)

This patch replaces calls to get_unused_fd() with equivalent call to
get_unused_fd_flags(0) to preserve current behavor for existing code.

In a further patch, get_unused_fd() will be removed so that new code start
using get_unused_fd_flags(), with the hope O_CLOEXEC could be used, either
by default or choosen by userspace.

Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

exit: ptrace: shift "reap dead" code from exit_ptrace() to forget_original_parent()

Now that forget_original_parent() uses ->ptrace_entry for EXIT_DEAD tasks,
we can simply pass "dead_children" list to exit_ptrace() and remove
another release_task() loop.  Plus this way we do not need to drop and
reacquire tasklist_lock.

Also shift the list_empty(ptraced) check, if we want this optimization it
makes sense to eliminate the function call altogether.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>,
Cc: Sterling Alexander <stalexan@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Roland McGrath <roland@hack.frob.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

exit: reparent: cleanup the usage of reparent_leader()

1. Now that reparent_leader() doesn't abuse ->sibling we can shift
   list_move_tail() from reparent_leader() to forget_original_parent()
   and turn it into a single list_splice_tail_init(). This also makes
   BUG_ON(!list_empty()) and list_for_each_entry_safe() unnecessary.

2. This also allows to shift the same_thread_group() check, it looks
   a bit more clear in the caller.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>,
Cc: Sterling Alexander <stalexan@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Roland McGrath <roland@hack.frob.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

exit: reparent: cleanup the changing of ->parent

1. Cosmetic, but "if (t->parent == father)" looks a bit confusing.
   We need to change t->parent if and only if t is not traced.

2. If we actually want this BUG_ON() to ensure that parent/ptrace
   match each other, then we should also take ptrace_reparented()
   case into account too.

3. Change this code to use for_each_thread() instead of deprecated
   while_each_thread().

[dan.carpenter@oracle.com: silence a bogus static checker warning]
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>,
Cc: Sterling Alexander <stalexan@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Roland McGrath <roland@hack.frob.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

exit: reparent: use ->ptrace_entry rather than ->sibling for EXIT_DEAD tasks

reparent_leader() reuses ->sibling as a list node to add an EXIT_DEAD task
into dead_children list we are going to release.  This obviously removes
the dead task from its real_parent->children list and this is even good;
the parent can do nothing with the EXIT_DEAD reparented zombie, it only
makes do_wait() slower.

But, this also means that it can not be reparented once again, so if its
new parent dies too nobody will update ->parent/real_parent, they can
point to the freed memory even before release_task() we are going to call,
this breaks the code which relies on pid_alive() to access
->real_parent/parent.

Fortunately this is mostly theoretical, this can only happen if init or
PR_SET_CHILD_SUBREAPER process ignores SIGCHLD and the new parent
sub-thread exits right after we drop tasklist_lock.

Change this code to use ->ptrace_entry instead, we know that the child is
not traced so nobody can ever use this member.  This also allows to unify
this logic with exit_ptrace(), see the next changes.

Note: we really need to change release_task() to nullify real_parent/
parent/group_leader pointers, but we need to change the current users
first somehow.  And it would be better to reap this zombie immediately but
release_task_locked() we need is complicated by proc_flush_task().

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>,
Cc: Sterling Alexander <stalexan@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Roland McGrath <roland@hack.frob.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sched_show_task: fix unsafe usage of ->real_parent

rcu_read_lock() can not protect p->real_parent if release_task(p) was
already called, change sched_show_task() to check pis_alive() like other
users do.

Note: we need some helpers to cleanup the code like this.  And it seems
that that the usage of cpu_curr(cpu) in dump_cpu_task() is not safe too.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>,
Cc: Sterling Alexander <stalexan@redhat.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Roland McGrath <roland@hack.frob.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

proc: task_state: ptrace_parent() doesn't need pid_alive() check

p->ptrace != 0 means that release_task(p) was not called, so pid_alive()
buys nothing and we can remove this check.  Other callers already use it
directly without additional checks.

Note: with or without this patch ptrace_parent() can return the pointer to
the freed task, this will be explained/fixed later.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>,
Cc: Sterling Alexander <stalexan@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Roland McGrath <roland@hack.frob.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

proc: task_state: move the main seq_printf() outside of rcu_read_lock()

task_state() does seq_printf() under rcu_read_lock(), but this is only
needed for task_tgid_nr_ns() and task_numa_group_id().  We can calculate
tgid/ngid and drop rcu lock.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>,
Cc: Sterling Alexander <stalexan@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Roland McGrath <roland@hack.frob.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

proc: task_state: deuglify the max_fds calculation

1. The usage of fdt looks very ugly, it can't be NULL if ->files is
   not NULL. We can use "unsigned int max_fds" instead.

2. This also allows to move seq_printf(max_fds) outside of task_lock()
   and join it with the previous seq_printf(). See also the next patch.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>,
Cc: Sterling Alexander <stalexan@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Roland McGrath <roland@hack.frob.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

proc: task_state: read cred->group_info outside of task_lock()

task_state() reads cred->group_info under task_lock() because a long ago
it was task_struct->group_info and it was actually protected by
task->alloc_lock.  Today this task_unlock() after rcu_read_unlock() just
adds the confusion, move task_unlock() up.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>,
Cc: Sterling Alexander <stalexan@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Roland McGrath <roland@hack.frob.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/proc.c: use rb_entry_safe() instead of rb_entry()

Better to use existing macro that rewriting them.

Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

procfs: fix error handling of proc_register()

proc_register() error paths are leaking inodes and directory refcounts.

Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/proc: use a rb tree for the directory entries

When a lot of netdevices are created, one of the bottleneck is the
creation of proc entries.  This serie aims to accelerate this part.

The current implementation for the directories in /proc is using a single
linked list.  This is slow when handling directories with large numbers of
entries (eg netdevice-related entries when lots of tunnels are opened).

This patch replaces this linked list by a red-black tree.

Here are some numbers:

dummy30000.batch contains 30 000 times 'link add type dummy'.

Before the patch:
  $ time ip -b dummy30000.batch
  real    2m31.950s
  user    0m0.440s
  sys     2m21.440s
  $ time rmmod dummy
  real    1m35.764s
  user    0m0.000s
  sys     1m24.088s

After the patch:
  $ time ip -b dummy30000.batch
  real    2m0.874s
  user    0m0.448s
  sys     1m49.720s
  $ time rmmod dummy
  real    1m13.988s
  user    0m0.000s
  sys     1m1.008s

The idea of improving this part was suggested by Thierry Herbelot.

[akpm@linux-foundation.org: initialise proc_root.subdir at compile time]
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Thierry Herbelot <thierry.herbelot@6wind.com>.
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: move page->mem_cgroup bad page handling into generic code

Now that the external page_cgroup data structure and its lookup is
gone, let the generic bad_page() check for page->mem_cgroup sanity.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Tejun Heo <tj@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: page_cgroup: rename file to mm/swap_cgroup.c

Now that the external page_cgroup data structure and its lookup is gone,
the only code remaining in there is swap slot accounting.

Rename it and move the conditional compilation into mm/Makefile.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Tejun Heo <tj@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: embed the memcg pointer directly into struct page

Memory cgroups used to have 5 per-page pointers.  To allow users to
disable that amount of overhead during runtime, those pointers were
allocated in a separate array, with a translation layer between them and
struct page.

There is now only one page pointer remaining: the memcg pointer, that
indicates which cgroup the page is associated with when charged.  The
complexity of runtime allocation and the runtime translation overhead is
no longer justified to save that *potential* 0.19% of memory.  With
CONFIG_SLUB, page->mem_cgroup actually sits in the doubleword padding
after the page->private member and doesn't even increase struct page,
and then this patch actually saves space.  Remaining users that care can
still compile their kernels without CONFIG_MEMCG.

     text    data     bss     dec     hex     filename
  8828345 1725264  983040 11536649 b00909  vmlinux.old
  8827425 1725264  966656 11519345 afc571  vmlinux.new

[mhocko@suse.cz: update Documentation/cgroups/memory.txt]
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Konstantin Khlebnikov <koct9i@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: remove stale page_cgroup_lock comment

There is no cgroup-specific page lock anymore.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/frontswap.c: fix the condition in BUG_ON

The largest index of swap device is MAX_SWAPFILES-1.  So the type should
be less than MAX_SWAPFILES.

Signed-off-by: Haifeng Li <omycle@gmail.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: fix a spelling mistake

Signed-off-by Wei Yuan <weiyuan.wei@huawei.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: hugetlb: fix __unmap_hugepage_range()

First, after flushing TLB, we have no need to scan pte from start again.
Second, before bail out loop, the address is forwarded one step.

Signed-off-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, memcg: fix potential undefined behaviour in page stat accounting

Since commit d7365e783edb ("mm: memcontrol: fix missed end-writeback
page accounting") mem_cgroup_end_page_stat consumes locked and flags
variables directly rather than via pointers which might trigger C
undefined behavior as those variables are initialized only in the slow
path of mem_cgroup_begin_page_stat.

Although mem_cgroup_end_page_stat handles parameters correctly and
touches them only when they hold a sensible value it is caller which
loads a potentially uninitialized value which then might allow compiler
to do crazy things.

I haven't seen any warning from gcc and it seems that the current
version (4.9) doesn't exploit this type undefined behavior but Sasha has
reported the following:

  UBSan: Undefined behaviour in mm/rmap.c:1084:2
  load of value 255 is not a valid value for type '_Bool'
  CPU: 4 PID: 8304 Comm: rngd Not tainted 3.18.0-rc2-next-20141029-sasha-00039-g77ed13d-dirty #1427
  Call Trace:
    dump_stack (lib/dump_stack.c:52)
    ubsan_epilogue (lib/ubsan.c:159)
    __ubsan_handle_load_invalid_value (lib/ubsan.c:482)
    page_remove_rmap (mm/rmap.c:1084 mm/rmap.c:1096)
    unmap_page_range (./arch/x86/include/asm/atomic.h:27 include/linux/mm.h:463 mm/memory.c:1146 mm/memory.c:1258 mm/memory.c:1279 mm/memory.c:1303)
    unmap_single_vma (mm/memory.c:1348)
    unmap_vmas (mm/memory.c:1377 (discriminator 3))
    exit_mmap (mm/mmap.c:2837)
    mmput (kernel/fork.c:659)
    do_exit (./arch/x86/include/asm/thread_info.h:168 kernel/exit.c:462 kernel/exit.c:747)
    do_group_exit (include/linux/sched.h:775 kernel/exit.c:873)
    SyS_exit_group (kernel/exit.c:901)
    tracesys_phase2 (arch/x86/kernel/entry_64.S:529)

Fix this by using pointer parameters for both locked and flags and be
more robust for future compiler changes even though the current code is
implemented correctly.

Signed-off-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: fix huge zero page accounting in smaps report

As a small zero page, huge zero page should not be accounted in smaps
report as normal page.

For small pages we rely on vm_normal_page() to filter out zero page, but
vm_normal_page() is not designed to handle pmds.  We only get here due
hackish cast pmd to pte in smaps_pte_range() -- pte and pmd format is not
necessary compatible on each and every architecture.

Let's add separate codepath to handle pmds.  follow_trans_huge_pmd() will
detect huge zero page for us.

We would need pmd_dirty() helper to do this properly.  The patch adds it
to THP-enabled architectures which don't yet have one.

[akpm@linux-foundation.org: use do_div to fix 32-bit build]
Signed-off-by: "Kirill A. Shutemov" <kirill@shutemov.name>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Tested-by: Fengwei Yin <yfw.kernel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: drop bogus RCU locking from mem_cgroup_same_or_subtree()

None of the mem_cgroup_same_or_subtree() callers actually require it to
take the RCU lock, either because they hold it themselves or they have css
references.  Remove it.

To make the API change clear, rename the leftover helper to
mem_cgroup_is_descendant() to match cgroup_is_descendant().

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: pull the NULL check from __mem_cgroup_same_or_subtree()

The NULL in mm_match_cgroup() comes from a possibly exiting mm->owner.  It
makes a lot more sense to check where it's looked up, rather than check
for it in __mem_cgroup_same_or_subtree() where it's unexpected.

No other callsite passes NULL to __mem_cgroup_same_or_subtree().

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: remove bogus NULL check after mem_cgroup_from_task()

That function acts like a typecast - unless NULL is passed in, no NULL can
come out.  task_in_mem_cgroup() callers don't pass NULL tasks.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: Michal Hocko <mhocko@suse.cz
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: shorten the page statistics update slowpath

While moving charges from one memcg to another, page stat updates must
acquire the old memcg's move_lock to prevent double accounting.  That
situation is denoted by an increased memcg->move_accounting.  However, the
charge moving code declares this way too early for now, even before
summing up the RSS and pre-allocating destination charges.

Shorten this slowpath mode by increasing memcg->move_accounting only right
before walking the task's address space with the intention of actually
moving the pages.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Reviewed-by: Vladimir Davydov <vdavydov@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

thp: do not mark zero-page pmd write-protected explicitly

Zero pages can be used only in anonymous mappings, which never have
writable vma->vm_page_prot: see protection_map in mm/mmap.c and __PX1X
definitions.

Let's drop redundant pmd_wrprotect() in set_huge_zero_page().

Signed-off-by: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memcg: use generic slab iterators for showing slabinfo

Let's use generic slab_start/next/stop for showing memcg caches info.  In
contrast to the current implementation, this will work even if all memcg
caches' info doesn't fit into a seq buffer (a page), plus it simply looks
neater.

Actually, the main reason I do this isn't mere cleanup.  I'm going to zap
the memcg_slab_caches list, because I find it useless provided we have the
slab_caches list, and this patch is a step in this direction.

It should be noted that before this patch an attempt to read
memory.kmem.slabinfo of a cgroup that doesn't have kmem limit set resulted
in -EIO, while after this patch it will silently show nothing except the
header, but I don't think it will frustrate anyone.

Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memcg: remove mem_cgroup_reclaimable check from soft reclaim

mem_cgroup_reclaimable() checks whether a cgroup has reclaimable pages on
*any* NUMA node.  However, the only place where it's called is
mem_cgroup_soft_reclaim(), which tries to reclaim memory from a *specific*
zone.  So the way it is used is incorrect - it will return true even if
the cgroup doesn't have pages on the zone we're scanning.

I think we can get rid of this check completely, because
mem_cgroup_shrink_node_zone(), which is called by
mem_cgroup_soft_reclaim() if mem_cgroup_reclaimable() returns true, is
equivalent to shrink_lruvec(), which exits almost immediately if the
lruvec passed to it is empty.  So there's no need to optimize anything
here.  Besides, we don't have such a check in the general scan path
(shrink_zone) either.

Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, hugetlb: correct bit shift in hstate_sizelog()

hstate_sizelog() would shift left an int rather than long, triggering
undefined behaviour and passing an incorrect value when the requested
page size was more than 4GB, thus breaking >4GB pages.

Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Andrey Ryabinin <a.ryabinin@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: fold mem_cgroup_start_move()/mem_cgroup_end_move()

Having these functions and their documentation split out and somewhere
makes it harder, not easier, to follow what's going on.

Inline them directly where charge moving is prepared and finished, and put
an explanation right next to it.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: don't pass a NULL memcg to mem_cgroup_end_move()

mem_cgroup_end_move() checks if the passed memcg is NULL, along with a
lengthy comment to explain why this seemingly non-sensical situation is
even possible.

Check in cancel_attach() itself whether can_attach() set up the move
context or not, it's a lot more obvious from there.  Then remove the check
and comment in mem_cgroup_end_move().

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: inline memcg->move_lock locking

The wrappers around taking and dropping the memcg->move_lock spinlock add
nothing of value.  Inline the spinlock calls into the callsites.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: remove unnecessary PCG_USED pc->mem_cgroup valid flag

pc->mem_cgroup had to be left intact after uncharge for the final LRU
removal, and !PCG_USED indicated whether the page was uncharged.  But
since commit 0a31bc97c80c ("mm: memcontrol: rewrite uncharge API") pages
are uncharged after the final LRU removal.  Uncharge can simply clear
the pointer and the PCG_USED/PageCgroupUsed sites can test that instead.

Because this is the last page_cgroup flag, this patch reduces the memcg
per-page overhead to a single pointer.

[akpm@linux-foundation.org: remove unneeded initialization of `memcg', per Michal]
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Reviewed-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: remove unnecessary PCG_MEM memory charge flag

PCG_MEM is a remnant from an earlier version of 0a31bc97c80c ("mm:
memcontrol: rewrite uncharge API"), used to tell whether migration cleared
a charge while leaving pc->mem_cgroup valid and PCG_USED set.  But in the
final version, mem_cgroup_migrate() directly uncharges the source page,
rendering this distinction unnecessary.  Remove it.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Reviewed-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: remove unnecessary PCG_MEMSW memory+swap charge flag

Now that mem_cgroup_swapout() fully uncharges the page, every page that is
still in use when reaching mem_cgroup_uncharge() is known to carry both
the memory and the memory+swap charge.  Simplify the uncharge path and
remove the PCG_MEMSW page flag accordingly.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Reviewed-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: uncharge pages on swapout

This series gets rid of the remaining page_cgroup flags, thus cutting the
memcg per-page overhead down to one pointer.

This patch (of 4):

mem_cgroup_swapout() is called with exclusive access to the page at the
end of the page's lifetime.  Instead of clearing the PCG_MEMSW flag and
deferring the uncharge, just do it right away.  This allows follow-up
patches to simplify the uncharge code.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Vladimir Davydov <vdavydov@parallels.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: micro-optimize mem_cgroup_split_huge_fixup()

Don't call lookup_page_cgroup() when memcg is disabled.

Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memcg: remove activate_kmem_mutex

The activate_kmem_mutex is used to serialize memcg.kmem.limit updates, but
we already serialize them with memcg_limit_mutex so let's remove the
former.

Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: clarify migration where old page is uncharged

Better explain re-entrant migration when compaction races with reclaim,
and also mention swapcache readahead pages as possible uncharged migration
sources.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: update mem_cgroup_page_lruvec() documentation

Commit 7512102cf64d ("memcg: fix GPF when cgroup removal races with last
exit") added a pc->mem_cgroup reset into mem_cgroup_page_lruvec() to
prevent a crash where an anon page gets uncharged on unmap, the memcg is
released, and then the final LRU isolation on free dereferences the
stale pc->mem_cgroup pointer.

But since commit 0a31bc97c80c ("mm: memcontrol: rewrite uncharge API"),
pages are only uncharged AFTER that final LRU isolation, which
guarantees the memcg's lifetime until then.  pc->mem_cgroup now only
needs to be reset for swapcache readahead pages.

Update the comment and callsite requirements accordingly.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memcg: simplify unreclaimable groups handling in soft limit reclaim

If we fail to reclaim anything from a cgroup during a soft reclaim pass
we want to get the next largest cgroup exceeding its soft limit. To
achieve this, we should obviously remove the current group from the tree
and then pick the largest group. Currently we have a weird loop instead.
Let's simplify it.

Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/numa balancing: rearrange Kconfig entry

Add the default enable config option after the NUMA_BALANCING option so
that it appears related in the nconfig interface.

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, compaction: more focused lru and pcplists draining

The goal of memory compaction is to create high-order freepages through
page migration.  Page migration however puts pages on the per-cpu lru_add
cache, which is later flushed to per-cpu pcplists, and only after pcplists
are drained the pages can actually merge.  This can happen due to the
per-cpu caches becoming full through further freeing, or explicitly.

During direct compaction, it is useful to do the draining explicitly so
that pages merge as soon as possible and compaction can detect success
immediately and keep the latency impact at minimum.  However the current
implementation is far from ideal.  Draining is done only in
__alloc_pages_direct_compact(), after all zones were already compacted,
and the decisions to continue or stop compaction in individual zones was
done without the last batch of migrations being merged.  It is also
missing the draining of lru_add cache before the pcplists.

This patch moves the draining for direct compaction into compact_zone().
It adds the missing lru_cache draining and uses the newly introduced
single zone pcplists draining to reduce overhead and avoid impact on
unrelated zones.  Draining is only performed when it can actually lead to
merging of a page of desired order (passed by cc->order).  This means it
is only done when migration occurred in the previously scanned cc->order
aligned block(s) and the migration scanner is now pointing to the next
cc->order aligned block.

The patch has been tested with stress-highalloc benchmark from mmtests.
Although overal allocation success rates of the benchmark were not
affected, the number of detected compaction successes has doubled.  This
suggests that allocations were previously successful due to implicit
merging caused by background activity, making a later allocation attempt
succeed immediately, but not attributing the success to compaction.  Since
stress-highalloc always tries to allocate almost the whole memory, it
cannot show the improvement in its reported success rate metric.  However
after this patch, compaction should detect success and terminate earlier,
reducing the direct compaction latencies in a real scenario.

Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Christoph Lameter <cl@linux.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, compaction: always update cached scanner positions

Compaction caches the migration and free scanner positions between
compaction invocations, so that the whole zone gets eventually scanned and
there is no bias towards the initial scanner positions at the
beginning/end of the zone.

The cached positions are continuously updated as scanners progress and the
updating stops as soon as a page is successfully isolated.  The reasoning
behind this is that a pageblock where isolation succeeded is likely to
succeed again in near future and it should be worth revisiting it.

However, the downside is that potentially many pages are rescanned without
successful isolation.  At worst, there might be a page where isolation
from LRU succeeds but migration fails (potentially always).  So upon
encountering this page, cached position would always stop being updated
for no good reason.  It might have been useful to let such page be
rescanned with sync compaction after async one failed, but this is now
handled by caching scanner position for async and sync mode separately
since commit 35979ef33931 ("mm, compaction: add per-zone migration pfn
cache for async compaction").

After this patch, cached positions are updated unconditionally.  In
stress-highalloc benchmark, this has decreased the numbers of scanned
pages by few percent, without affecting allocation success rates.

To prevent free scanner from leaving free pages behind after they are
returned due to page migration failure, the cached scanner pfn is changed
to point to the pageblock of the returned free page with the highest pfn,
before leaving compact_zone().

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Christoph Lameter <cl@linux.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, compaction: defer only on COMPACT_COMPLETE

Deferred compaction is employed to avoid compacting zone where sync direct
compaction has recently failed.  As such, it makes sense to only defer
when a full zone was scanned, which is when compact_zone returns with
COMPACT_COMPLETE.  It's less useful to defer when compact_zone returns
with apparent success (COMPACT_PARTIAL), followed by a watermark check
failure, which can happen due to parallel allocation activity.  It also
does not make much sense to defer compaction which was completely skipped
(COMPACT_SKIP) for being unsuitable in the first place.

This patch therefore makes deferred compaction trigger only when
COMPACT_COMPLETE is returned from compact_zone().  Results of
stress-highalloc becnmark show the difference is within measurement error,
so the issue is rather cosmetic.

Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Christoph Lameter <cl@linux.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, compaction: simplify deferred compaction

Since commit 53853e2d2bfb ("mm, compaction: defer each zone individually
instead of preferred zone"), compaction is deferred for each zone where
sync direct compaction fails, and reset where it succeeds.  However, it
was observed that for DMA zone compaction often appeared to succeed
while subsequent allocation attempt would not, due to different outcome
of watermark check.

In order to properly defer compaction in this zone, the candidate zone
has to be passed back to __alloc_pages_direct_compact() and compaction
deferred in the zone after the allocation attempt fails.

The large source of mismatch between watermark check in compaction and
allocation was the lack of alloc_flags and classzone_idx values in
compaction, which has been fixed in the previous patch.  So with this
problem fixed, we can simplify the code by removing the candidate_zone
parameter and deferring in __alloc_pages_direct_compact().

After this patch, the compaction activity during stress-highalloc
benchmark is still somewhat increased, but it's negligible compared to the
increase that occurred without the better watermark checking.  This
suggests that it is still possible to apparently succeed in compaction but
fail to allocate, possibly due to parallel allocation activity.

[akpm@linux-foundation.org: fix build]
Suggested-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, compaction: pass classzone_idx and alloc_flags to watermark checking

Compaction relies on zone watermark checks for decisions such as if it's
worth to start compacting in compaction_suitable() or whether compaction
should stop in compact_finished().  The watermark checks take
classzone_idx and alloc_flags parameters, which are related to the memory
allocation request.  But from the context of compaction they are currently
passed as 0, including the direct compaction which is invoked to satisfy
the allocation request, and could therefore know the proper values.

The lack of proper values can lead to mismatch between decisions taken
during compaction and decisions related to the allocation request.  Lack
of proper classzone_idx value means that lowmem_reserve is not taken into
account.  This has manifested (during recent changes to deferred
compaction) when DMA zone was used as fallback for preferred Normal zone.
compaction_suitable() without proper classzone_idx would think that the
watermarks are already satisfied, but watermark check in
get_page_from_freelist() would fail.  Because of this problem, deferring
compaction has extra complexity that can be removed in the following
patch.

The issue (not confirmed in practice) with missing alloc_flags is opposite
in nature.  For allocations that include ALLOC_HIGH, ALLOC_HIGHER or
ALLOC_CMA in alloc_flags (the last includes all MOVABLE allocations on
CMA-enabled systems) the watermark checking in compaction with 0 passed
will be stricter than in get_page_from_freelist().  In these cases
compaction might be running for a longer time than is really needed.

Another issue compaction_suitable() is that the check for "does the zone
need compaction at all?" comes only after the check "does the zone have
enough free free pages to succeed compaction".  The latter considers extra
pages for migration and can therefore in some situations fail and return
COMPACT_SKIPPED, although the high-order allocation would succeed and we
should return COMPACT_PARTIAL.

This patch fixes these problems by adding alloc_flags and classzone_idx to
struct compact_control and related functions involved in direct compaction
and watermark checking.  Where possible, all other callers of
compaction_suitable() pass proper values where those are known.  This is
currently limited to classzone_idx, which is sometimes known in kswapd
context.  However, the direct reclaim callers should_continue_reclaim()
and compaction_ready() do not currently know the proper values, so the
coordination between reclaim and compaction may still not be as accurate
as it could.  This can be fixed later, if it's shown to be an issue.

Additionaly the checks in compact_suitable() are reordered to address the
second issue described above.

The effect of this patch should be slightly better high-order allocation
success rates and/or less compaction overhead, depending on the type of
allocations and presence of CMA.  It allows simplifying deferred
compaction code in a followup patch.

When testing with stress-highalloc, there was some slight improvement
(which might be just due to variance) in success rates of non-THP-like
allocations.

Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Christoph Lameter <cl@linux.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: vmscan: count only dirty pages as congested

shrink_page_list() counts all pages with a mapping, including clean pages,
toward nr_congested if they're on a write-congested BDI.
shrink_inactive_list() then sets ZONE_CONGESTED if nr_dirty ==
nr_congested.  Fix this apples-to-oranges comparison by only counting
pages for nr_congested if they count for nr_dirty.

Signed-off-by: Jamie Liu <jamieliu@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Greg Thelen <gthelen@google.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: verify compound order when freeing a page

This allows us to catch the bug fixed in the previous patch (mm: free
compound page with correct order).

Here we also verify whether a page is tail page or not -- tail pages are
supposed to be freed along with their head, not by themselves.

Signed-off-by: Yu Zhao <yuzhao@google.com>
Reviewed-by: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: David Rientjes <rientjes@google.com>
Cc: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

cma: make default CMA area size zero for x86

This makes CMA memory area size zero for x86 in default configuration
(doesn't change on the other architectures).  If default CMA size is
zero, DMA_CMA is disabled.  It can be enabled by passing cma= to the
kernel.

This makes less impact on x86.  Because there is no mainline driver that
requires it for x86, and Peter Hurley reported the performance
regression, as this is trying to drive _all_ dma mapping allocations
through a _very_ small window.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Chuck Ebbert <cebbert.lkml@gmail.com>
Cc: Jean Delvare <jdelvare@suse.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Don Dutile <ddutile@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, memory_hotplug/failure: drain single zone pcplists

Memory hotplug and failure mechanisms have several places where pcplists
are drained so that pages are returned to the buddy allocator and can be
e.g. prepared for offlining.  This is always done in the context of a
single zone, we can reduce the pcplists drain to the single zone, which
is now possible.

The change should make memory offlining due to hotremove or failure
faster and not disturbing unrelated pcplists anymore.

Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, cma: drain single zone pcplists

CMA allocation drains pcplists so that pages can merge back to buddy
allocator.  Since it operates on a single zone, we can reduce the
pcplists drain to the single zone, which is now possible.

The change should make CMA allocations faster and not disturbing
unrelated pcplists anymore.

Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, page_isolation: drain single zone pcplists

When setting MIGRATETYPE_ISOLATE on a pageblock, pcplists are drained to
have a better chance that all pages will be successfully isolated and
not left in the per-cpu caches.  Since isolation is always concerned
with a single zone, we can reduce the pcplists drain to the single zone,
which is now possible.

The change should make memory isolation faster and not disturbing
unrelated pcplists anymore.

Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: introduce single zone pcplists drain

The functions for draining per-cpu pages back to buddy allocators
currently always operate on all zones.  There are however several cases
where the drain is only needed in the context of a single zone, and
spilling other pcplists is a waste of time both due to the extra
spilling and later refilling.

This patch introduces new zone pointer parameter to drain_all_pages()
and changes the dummy parameter of drain_local_pages() to be also a zone
pointer.  When NULL is passed, the functions operate on all zones as
usual.  Passing a specific zone pointer reduces the work to the single
zone.

All callers are updated to pass the NULL pointer in this patch.
Conversion to single zone (where appropriate) is done in further
patches.

Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/vmscan.c: replace printk with pr_err

This patch replaces printk(KERN_ERR..) with pr_err found under
shrink_slab.  Thus it also reduces one line extra because of formatting.

Signed-off-by: Pintu Kumar <pintu.k@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/vmalloc.c: replace printk with pr_warn

This patch replaces printk(KERN_WARNING..) with pr_warn.
Thus it also reduces one line extra because of formatting.

Signed-off-by: Pintu Kumar <pintu.k@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/page_alloc.c: convert boot printks without log level to pr_info

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: remove synchronous stock draining code

With charge reparenting, the last synchronous stock drainer left.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: continue cache reclaim from offlined groups

On cgroup deletion, outstanding page cache charges are moved to the parent
group so that they're not lost and can be reclaimed during pressure
on/inside said parent.  But this reparenting is fairly tricky and its
synchroneous nature has led to several lock-ups in the past.

Since c2931b70a32c ("cgroup: iterate cgroup_subsys_states directly") css
iterators now also include offlined css, so memcg iterators can be changed
to include offlined children during reclaim of a group, and leftover cache
can just stay put.

There is a slight change of behavior in that charges of deleted groups no
longer show up as local charges in the parent.  But they are still
included in the parent's hierarchical statistics.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: remove obsolete kmemcg pinning tricks

As charges now pin the css explicitely, there is no more need for kmemcg
to acquire a proxy reference for outstanding pages during offlining, or
maintain state to identify such "dead" groups.

This was the last user of the uncharge functions' return values, so remove
them as well.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: take a css reference for each charged page

Charges currently pin the css indirectly by playing tricks during
css_offline(): user pages stall the offlining process until all of them
have been reparented, whereas kmemcg acquires a keep-alive reference if
outstanding kernel pages are detected at that point.

In preparation for removing all this complexity, make the pinning explicit
and acquire a css references for every charged page.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: convert reclaim iterator to simple css refcounting

The memcg reclaim iterators use a complicated weak reference scheme to
prevent pinning cgroups indefinitely in the absence of memory pressure.

However, during the ongoing cgroup core rework, css lifetime has been
decoupled such that a pinned css no longer interferes with removal of
the user-visible cgroup, and all this complexity is now unnecessary.

[mhocko@suse.cz: ensure that the cached reference is always released]
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel: res_counter: remove the unused API

All memory accounting and limiting has been switched over to the
lockless page counters.  Bye, res_counter!

[akpm@linux-foundation.org: update Documentation/cgroups/memory.txt]
[mhocko@suse.cz: ditch the last remainings of res_counter]
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Tejun Heo <tj@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: hugetlb_cgroup: convert to lockless page counters

Abandon the spinlock-protected byte counters in favor of the unlocked
page counters in the hugetlb controller as well.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Tejun Heo <tj@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>