Bjorn Andersson [Tue, 16 Apr 2019 23:49:27 +0000 (16:49 -0700)]
iio: adc: qcom-spmi-adc5: Fix of-based module autoloading
The of_device_id table needs to be registered as module alias in order
for automatic module loading to pick the kernel module based on the
DeviceTree compatible. So add MODULE_DEVICE_TABLE() to make this happen.
Fixes:
e13d757279bb ("iio: adc: Add QCOM SPMI PMIC5 ADC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pan Bian [Thu, 18 Apr 2019 03:02:56 +0000 (11:02 +0800)]
iio: dummy_evgen: fix possible memleak in evgen init
The memory allocated in the function iio_dummy_evgen_create is not
released if it fails to add the evgen device to device hierarchy. This
may result in a memory leak bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Mohan Kumar [Fri, 19 Apr 2019 08:36:51 +0000 (11:36 +0300)]
iio:accel:Switch hardcoded function name with a reference to __func__ making the code more maintainable
It fixes the following checkpatch.pl warning:
WARNING: Prefer using '"%s...", __func__' to using function's name, in a
string
Signed-off-by: Mohan Kumar <mohankumar718@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fabrice Gasnier [Mon, 15 Apr 2019 13:00:51 +0000 (15:00 +0200)]
iio: adc: stm32-dfsdm: fix triggered buffer build dependency
This fixes build errors seen when CONFIG_STM32_DFSDM_ADC is set, as
stm32-dfsdm-adc driver now also relies on triggered buffer API:
Fixes:
11646e81d775 ("iio: adc: stm32-dfsdm: add support for buffer modes")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fabrice Gasnier [Mon, 15 Apr 2019 13:00:50 +0000 (15:00 +0200)]
iio: adc: stm32-dfsdm: fix unmet direct dependencies detected
This fixes unmet direct dependencies seen when CONFIG_STM32_DFSDM_ADC
is selected:
WARNING: unmet direct dependencies detected for IIO_BUFFER_HW_CONSUMER
Depends on [n]: IIO [=y] && IIO_BUFFER [=n]
Selected by [y]:
- STM32_DFSDM_ADC [=y] && IIO [=y] && (ARCH_STM32 [=y] && OF [=y] ||
COMPILE_TEST [=n])
Fixes:
e2e6771c6462 ("IIO: ADC: add STM32 DFSDM sigma delta ADC support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fabrice Gasnier [Mon, 15 Apr 2019 09:47:22 +0000 (11:47 +0200)]
iio: trigger: stm32-timer: fix build issue when disabled
This fixes a build issue when CONFIG_IIO_STM32_TIMER_TRIGGER isn't set but
used in stm32-dfsdm-adc driver (e.g. CONFIG_STM32_DFSDM_ADC is set):
ERROR: "is_stm32_timer_trigger" [drivers/iio/adc/stm32-dfsdm-adc.ko]
undefined!
There are two possible options to fix this issue:
- select IIO_STM32_TIMER_TRIGGER along with CONFIG_STM32_DFSDM_ADC.
This is what's being done currently for CONFIG_STM32_ADC.
- stub "is_stm32_timer_trigger" function
Choice is made to stub this function as suggested in [1]. This is also
inspired by similar "is_stm32_lptim_trigger" function (see [2]) in
include/linux/iio/timer/stm32-lptim-trigger.h
[1]
https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg1977377.html
[2] https://lkml.org/lkml/2017/9/10/124
Fixes:
11646e81d775 ("iio: adc: stm32-dfsdm: add support for buffer modes")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fix-suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andrey Smirnov [Sun, 14 Apr 2019 18:35:04 +0000 (11:35 -0700)]
iio: imx7d_adc: Use devm_iio_device_register()
Use devm_iio_device_register() and drop imx7d_adc_remove().
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-iio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andrey Smirnov [Sun, 14 Apr 2019 18:35:03 +0000 (11:35 -0700)]
iio: imx7d_adc: Simplify imx7d_adc_remove() with imx7d_adc_suspend()
Since imx7d_adc_remove() does exactly the same thing as
imx7d_adc_suspend() we can use the latter together with
devm_add_action_or_reset() to simplify the former. Rename
imx7d_adc_suspend() to imx7d_adc_disable() for clarity while at it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-iio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andrey Smirnov [Sun, 14 Apr 2019 18:35:02 +0000 (11:35 -0700)]
iio: imx7d_adc: Simplify imx7d_adc_probe() with imx7d_adc_resume()
Initialization sequence performed in imx7d_adc_resume() is exactly the
same as the one being done in imx7d_adc_probe(). Make use of the
former in the latter to avoid code duplication. Rename
imx7d_adc_resume() to imx7d_adc_enable() for clarity while at it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-iio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Mohan Kumar [Sun, 14 Apr 2019 15:53:38 +0000 (18:53 +0300)]
drivers/iio/gyro/mpu3050-core.c: This patch fix the following checkpatch warning.
As per Documentation/timers/timers-howto.txt Msleep < 20ms can sleep for
up to 20ms. so use usleep_range.
Signed-off-by: Mohan Kumar <mohankumar718@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Mircea Caprioru [Tue, 9 Apr 2019 13:35:21 +0000 (16:35 +0300)]
iio: dac: ad5758: Modifications for new revision
This patch will ensure compatibility with the new revision of the AD5758
dac converter. The modifications consist of removing the fault_prot_switch
function since this option is no longer available, and enabling the
ENABLE_PPC_BUFFERS bit in ADC_CONFIG register before setting the PPC
current mode.
The previous version of the chip was never released to customers
so there is no need to support it going forwards.
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Lorenzo Bianconi [Tue, 9 Apr 2019 20:49:09 +0000 (22:49 +0200)]
iio: imu: st_lsm6dsx: inline per-sensor data
As it has been already done for other st sensors in 'commit
9049531c91b4
("iio: accel: st_accel: inline per-sensor data")', get rid of some
defines and just open code the values into the appropriate struct
elements since the semantic meaning is inherent in the name of the
C99-addressable fields and there is no reason to duplicate the code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Gregory CLEMENT [Fri, 12 Apr 2019 09:15:37 +0000 (11:15 +0200)]
iio: adc: Add driver for the TI ADS8344 A/DC chips
This adds support for the Texas Instruments ADS8344 ADC chip. This chip
has a 16-bit 8-Channel ADC and is access directly through SPI.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Gregory CLEMENT [Fri, 12 Apr 2019 09:15:36 +0000 (11:15 +0200)]
dt-bindings: iio: adc: Add bindings for TI ADS8344 A/DC chips
This adds device tree bindings for the TI ADS8344 A/DC chips.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rui Miguel Silva [Fri, 12 Apr 2019 16:49:01 +0000 (17:49 +0100)]
MAINTAINERS: add entry for fxas21002c gyro driver
Add me as maintainer of the nxp fxas21002c gyroscope driver.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rui Miguel Silva [Fri, 12 Apr 2019 16:48:59 +0000 (17:48 +0100)]
iio: gyro: fxas21002c: add spi driver
Add driver to talk over spi to a fxas21002c gyroscope device and use
the core as main controller.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rui Miguel Silva [Fri, 12 Apr 2019 16:48:58 +0000 (17:48 +0100)]
iio: gyro: fxas21002c: add i2c driver
Add the real driver to talk over i2c and use the fxas21002c core
for the main tasks.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rui Miguel Silva [Fri, 12 Apr 2019 16:48:57 +0000 (17:48 +0100)]
iio: gyro: add core driver for fxas21002c
Add core support for the NXP fxas21002c Tri-axis gyroscope,
using the iio subsystem. It supports PM operations, axis reading,
temperature, scale factor of the axis, high pass and low pass
filtering, and sampling frequency selection.
It will have extras modules to support the communication over i2c and
spi.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rui Miguel Silva [Fri, 12 Apr 2019 16:48:56 +0000 (17:48 +0100)]
iio: gyro: add DT bindings to fxas21002c
Add device tree bindings for the FXAS21002C gyroscope.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andreas Klinger [Tue, 9 Apr 2019 19:11:28 +0000 (21:11 +0200)]
Kconfig: change configuration of srf04 ultrasonic iio sensor
reword configuration option for SRF04
list supported types in help text
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andreas Klinger [Tue, 9 Apr 2019 19:10:55 +0000 (21:10 +0200)]
dt-bindings: iio: srf04: add Maxbotix ultrasonic iio proximity sensors
add compatibles for Maxbotix ultrasonic iio sensor types to yaml
documentation
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andreas Klinger [Tue, 9 Apr 2019 19:10:22 +0000 (21:10 +0200)]
srf04.c: add maxbotix ultrasonic sensors
add Maxbotix LV ultrasonic sensor types mb1000, mb1010, mb1020, mb1030
and mb1040
add a configuration struct with the different trigger pulse lengths
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
YueHaibing [Wed, 10 Apr 2019 08:45:58 +0000 (16:45 +0800)]
iio: adc: ti-ads7950: Fix build error without CONFIG_GPIOLIB
When building with CONFIG_GPIOLIB is not set
gcc warns this:
drivers/iio/adc/ti-ads7950.c:75:19: error: field chip has incomplete type
struct gpio_chip chip;
^~~~
drivers/iio/adc/ti-ads7950.c: In function ti_ads7950_set:
drivers/iio/adc/ti-ads7950.c:409:32: error: implicit declaration of function gpiochip_get_data; did you mean acpi_get_data? [-Werror=implicit-function-declaration]
struct ti_ads7950_state *st = gpiochip_get_data(chip);
^~~~~~~~~~~~~~~~~
acpi_get_data
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes:
c97dce792dc8 ("iio: adc: ti-ads7950: add GPIO support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Justin Chen <justinpopo6@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Colin Ian King [Wed, 10 Apr 2019 18:23:51 +0000 (19:23 +0100)]
iio: temperature: max31856: fix uninitialized error return
Currently if mask is neither CHAN_INFO_RAW or CHAN_INFO_SCALE then
then an uninitialized error return 'ret' is returned. Fix this by
adding a default case that ensures -EINVAL is returned for this
specific case.
Addresses-Coverity: ("Uninitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
YueHaibing [Tue, 9 Apr 2019 02:12:17 +0000 (02:12 +0000)]
iio: imu: st_lsm6dsx: remove set but not used variables 'acc_sensor' and 'gyro_sensor'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c: In function 'st_lsm6dsx_read_tagged_fifo':
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c:520:41: warning:
variable 'gyro_sensor' set but not used [-Wunused-but-set-variable]
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c:520:28: warning:
variable 'acc_sensor' set but not used [-Wunused-but-set-variable]
They are not used since commit
14c7c6e1a860 ("iio: imu: st_lsm6dsx: add
st_lsm6dsx_push_tagged_data routine")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Robert Jones [Thu, 11 Apr 2019 00:12:09 +0000 (17:12 -0700)]
iio: accel: add support to LIS2DE12
Add support to STMicroelectronics LIS2DE12 accelerometer in
st_accel framework.
http://www.st.com/resource/en/datasheet/lis2de12.pdf
Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Robert Jones [Thu, 11 Apr 2019 00:12:08 +0000 (17:12 -0700)]
dt-bindings: iio: accel: add LIS2DE12 sensor device binding
Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Valentin Manea [Sun, 31 Mar 2019 14:54:08 +0000 (14:54 +0000)]
iio: accel: kxcjk1013: Add KIOX0008 ACPI Hardware-ID
Add the ACPI ID for KXCJ9 sensor seen on the a Teclast X80 Power
tablet.
Signed-off-by: Valentin Manea <linux-iio@mrs.ro>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Marcelo Schmitt [Mon, 1 Apr 2019 14:37:45 +0000 (11:37 -0300)]
staging: iio: ad9832: use clock framework for clock reference
Previously external clock were set through platform_data struct.
Now device uses clk struct defined in include/linux/clk.h to handle
external clock source.
It also removes mclk from platform_data struct.
Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Marcelo Schmitt [Mon, 1 Apr 2019 14:37:10 +0000 (11:37 -0300)]
staging: iio: ad9832: organize includes
Organize includes to list them in lexicographic order.
Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andreas Klinger [Mon, 1 Apr 2019 17:31:44 +0000 (19:31 +0200)]
bmp085.yaml: transform DT documentation of iio sensor into YAML
use bmp085.txt and change it into yaml format
fix links to datasheets in replaced documentation
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andreas Klinger [Mon, 1 Apr 2019 17:33:54 +0000 (19:33 +0200)]
avia-hx711.yaml: transform DT binding to YAML
replace avia-hx711.txt by avia-hx711.yaml as yaml devicetree
documentation for avia hx711 iio adc sensor
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andrey Smirnov [Wed, 3 Apr 2019 07:03:23 +0000 (00:03 -0700)]
iio: imx7d_adc: Use devm_platform_ioremap_resource()
Use devm_platform_ioremap_resource() to be able to drop a bit of
explicit boilerplate code.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-iio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andrey Smirnov [Wed, 3 Apr 2019 07:03:21 +0000 (00:03 -0700)]
iio: imx7d_adc: Replace pr_err with dev_err
Replace combination of pr_err()/dev_name() with an equivalent call for
dev_err().
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-iio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andrey Smirnov [Wed, 3 Apr 2019 07:03:20 +0000 (00:03 -0700)]
iio: imx7d_adc: Add local struct device pointer in imx7d_adc_probe()
Use a local "struct device *dev" in imx7d_adc_probe() for brevity. No
functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-iio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Beniamin Bia [Tue, 2 Apr 2019 13:18:41 +0000 (16:18 +0300)]
dt-bindings: iio: adc: Add AD7616 ADC documentation
Document support for AD7616 Analog to Digital Converter.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Beniamin Bia [Tue, 2 Apr 2019 13:18:40 +0000 (16:18 +0300)]
iio: adc: ad7616: Add support for AD7616 ADC
The AD7616 is a 12-bit ADC with 16 channels.
The AD7616 can be configured to work in hardware mode by controlling it via
gpio pins and read data via spi. No support for software mode yet, but it
is a work in progress.
This device requires a reset in order to update oversampling, so chip info
has got a new attribute to mark this.
The current assumption that this driver makes for AD7616, is that it's
working in Hardware Mode with Serial, Burst and Sequencer modes activated.
To activate them, following pins must be pulled high:
-SER/PAR
-SEQEN
And following must be pulled low:
-WR/BURST
-DB4/SEQEN
Datasheets:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ad7616.pdf
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stefan Popa [Tue, 2 Apr 2019 13:18:39 +0000 (16:18 +0300)]
iio: adc: ad7606: Move oversampling options in chip info and rework *_avail attributes
Available oversampling ratios and scales can be shown by calling a
common ad7606_show_avail function which takes as parameters the array
which stores the values, together with the size of the array.
Oversampling options are now defined in chip info
structure and they are loaded at probe.
Has_Oversampling attribute was removed because oversampling_num was added
and it is not needed anymore.
The purpose of this patch is to deal with the scale_avail and
oversampling_avail arrays in a generic way. This makes it easier to add
support for new devices which will work with different scales and
oversampling ratios. It is also an intermediate step for adding support
for ad7616 which has different oversampling sampling ratios available.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Melissa Wen [Tue, 2 Apr 2019 20:18:54 +0000 (17:18 -0300)]
staging: iio: frequency: ad9834: Remove unnecessary parentheses
Remove unneeded parentheses around the arguments of ||. This reduces
clutter and code behave in the same way. Change suggested by
checkpatch.pl.
CHECK: Unnecessary parentheses around 'st->devid == ID_AD9833'
CHECK: Unnecessary parentheses around 'st->devid == ID_AD9837'
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fabrizio Castro [Wed, 3 Apr 2019 15:03:51 +0000 (16:03 +0100)]
iio: adc: Fix MAX9611 spacing
Between "config" and "MAX9611" there is a tab, replace it
with a space.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Lorenzo Bianconi [Thu, 4 Apr 2019 16:02:35 +0000 (18:02 +0200)]
dt-bindings: iio: imu: st_lsm6dsx: add lsm6dsr device bindings
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Lorenzo Bianconi [Thu, 4 Apr 2019 16:02:34 +0000 (18:02 +0200)]
iio: imu: st_lsm6dsx: add support to LSM6DSR
Add support to STM LSM6DSR 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/lsm6dsr.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Greg Kroah-Hartman [Thu, 4 Apr 2019 20:25:29 +0000 (22:25 +0200)]
Merge tag 'iio-for-5.2a-2' of git://git./linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and fixes for IIO in the 5.2 cycle
Staging graduations
* ad7780
- Move this ADC driver out of staging. Included adding some new features
along the way (see below). Also added DT bindings.
New device support
* adis16480
- Support the ADIS16495 and ADIS16497 IMU devices making
heavy use of refactoring of various aspects of the driver in precursor
patches.
* lsm6dsx
- Support for the ASM330LHH 6-axis (accelerometer + gyro) sensor.
- Support for the LSM6DS0X
* matbotix mb1232
- New driver for this ultrasound ranging device family. Including bindings.
- Supports mb1202, mb1212, mb1222, mb1232, mb1242, mb7040 and mb7137.
* max31856
- New driver for this thermocouple temperature sensor.
* meson saradc
- Support the Meson-G12A (ID addition only).
* stmpe-adc
- New driver supporting generic ADC alongside touchscreen support which
previously existed. Includes DT bindings.
* vcnl4000
- Support for the vcln4040 proximity and light sensor, including adding
DT bindings for this and parts previously supported.
Features
* core
- Allow reading of mount matrices from ACPI in addition to DT.
- Common binding for theromcouple types.
* ad5933
- Add ABI docs as there are a few 'unsual' elements about this
device - perhaps because it's our only impedance analyser.
* ad7780
- Add gain and filter gpio support + readback of current gain and filter.
* adis16480
- Allow selection fo the dataready pin to be used.
- Device tree ID table and binding documentation.
- Support external clock modes, including new bindings.
* bma180
- Mount matrix support.
* bmc150
- Mount matrix support.
* bmg160
- Mount matrix support.
- DT id table and bindings doc.
* bmp280
- Put calibration data into the entropy pool.
* hmc5843
- Mount matrix support.
* itg3200
- Mount matrix support.
* kxcjk1013
- Device tree id table, and binding docs.
* lpc32xx
- Add scale when regulator specified including DT docs for regulator.
* pms7003
- Add device IDs for all supported parts to driver and binding.
* stm32-dfsdm
- Enable hw consumer support, scan mode control and a complex set of
triggered buffer modes.
- Power management.
* stm32-lptimer-counter
- power management.
- Document the pinctrl sleep state binding.
* ti-ads7950
- GPIO pin support.
Cleanups, minor fixes
* core
- Use bitmap_zalloc to make it explicit that is what we are doing.
- Tidy up all the Kconfig files (which had slowly gotten messy)
- Fix a forwards definition missing issue in iio/driver.h
* ad sigma delta core
- Improve handling of SPI bus locking vs CS assertion. This has been
wrong a long time so not rushing this in.
* ad5064
- Mlock to local lock.
* ad5933 (staging cleanup)
- Multiline comment fixes.
- Include ordering.
- SPDX.
- Tidy up Kconfig help which was a bit missleading.
- Change some non standard attributes to ABI defined ones.
* ad7124
- White space fix.
* ad7192
- White space.
- Use DT clock binding.
- Improve error reporting.
- Platform data to DT conversion.
- Use read_avail callback, mostly to avoid the endless series of
patches from new contributors trying to falsely put spaces around
the negative sign.
* ad7280a
- Add brackets to macros to avoid potential precedence isseus.
- Add temp vars for event codes to reduce indent and improved readability.
- Clean out som CamelCase notation.
- White space.
* ad7606
- Fix broken file naming in MAINTAINERS.
* ad7780
- Missing switch defaults to supress warnings and harden the code slightly.
- Set pattern masks more directly.
- Add ID values and masks for all supported chips.
- SPDX + add Renato as a copyright holder as he has done a lot of work on
this driver.
- Add brackets to macros to avoid potential precedence issues.
* ad7923
- White space fixes.
- Use BIT macro to improve readability.
- Add brackets to macros to avoid potential precedence issues.
- Tidy up a null comparisom.
* ad9523
- Fix a typo in naming of variables.
* adis16400
- Combine trigger file into main code as no advantage in separate files.
Rename core file to just adis16400.
- Squash the header into the c file now there is only one file.
- Generalize burst mode to support new variants.
* ak8975
- Local variable to improve readability around mount matrix support.
* as3935
- Avoid potential race by ensuring remove does exact opposite of
probe rather than a slightly different order.
* cross_ec
- Drop some unnecessary includes.
- Fix some warning and the slightly 'unusual' code.
- Add some docs for non obvious function.
- SPDX
* hmc5843
- Potential unhandled error case.
* iio trigger core
- Print an error if there is no available irq due to max consumers per
trigger being set to low.
* iio loop trigger
- Drop an unlikely on IS_ERR as IS_ERR already has the annotation.
* ingenic-adc
- Drop a redundant dev_err call as devm_ioremap_resource reports the same
internally.
* lmp91000
- Drop some unncessary parentheses and white space tidy up.
- Invert and if statement to improve readability.
- Fix a wrong error message.
* lpc32xx
- Header sorting + drop some unused ones.
* mma8542
- Mark a switch fallthrough.
* mpu6050
- Add a local variable to improve code readability around mount matrix
support.
* mxs-lradc-adc
- Handle devm_iio_trigger_alloc failure.
* sps30
- Fix up a kernel version in the ABI docs.
* srf04
- DT binding doc converted to yaml.
* ssp_sensors
- Supress a clang build warning due to lack of visibility of conditional
within a iio_push_to_buffers_with_timestamp. (reasonable false warning!)
* st_accel
- Drop pointless less than 0 comparisom of unsigned int.
* stm32-dfsdm
- Improve accuracy of spi_master_frequency calculation.
- Improve calculation fo sampling frequency.
- Rework various internals to simplify adding triggered buffer support.
- Claim direct mode to avoid racing around read_raw and being in buffered
mode.
* stmpe
- Fix a clang false positive warning.
* ti-ads7950
- Use local lock rather than using the core mlock when not locking around
the device mode.
* vcnl4000
- Use word writes instead of byte writes. It seems byte writes are fine
for some parts (undocument) but not others that the driver will shortly
support.
Other
* mailmap
- Add email address change for Sean Nyekjaer. Update in relevant drivers
* tag 'iio-for-5.2a-2' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (129 commits)
iio: ad_sigma_delta: Properly handle SPI bus locking vs CS assertion
iio: adc: stm32-dfsdm: add PM support
iio: adc: stm32-dfsdm: improve sampling frequency accuracy
staging: iio: adc: ad7280a: Tab alignment
MAINTAINERS: Fix the link to ad7606 dt-bindings
iio:temperature: Add MAX31856 thermocouple support
iio:temperature:max31856:Add device tree bind info
dt-bindings: iio/temperature: Add thermocouple types (and doc)
devantech-srf04.yaml: transform DT binding to YAML
iio: frequency: ad9523: Fix typo in ad9523_platform_data
iio: Make possible to include driver.h first
dt-bindings: iio: add Bosch BMG160 gyroscope sensor
iio: gyro: bmg160: add device tree compatibility table
staging: iio: adc: ad7192: Use read_avail for available attributes
dt-bindings: iio: light: add vcnl4040 devicetree bindings
iio: light: vcnl4000 add support for the VCNL4040 proximity and light sensor
dt-bindings: iio: light: add vcnl4000 devicetree bindings
iio: light: vcnl4000 add devicetree hooks
iio: light: vcnl4000 use word writes instead of byte writes
iio: adc: stm32-dfsdm: claim direct mode for raw read and settings
...
Lars-Peter Clausen [Tue, 19 Mar 2019 11:37:55 +0000 (13:37 +0200)]
iio: ad_sigma_delta: Properly handle SPI bus locking vs CS assertion
For devices from the SigmaDelta family we need to keep CS low when doing a
conversion, since the device will use the MISO line as a interrupt to
indicate that the conversion is complete.
This is why the driver locks the SPI bus and when the SPI bus is locked
keeps as long as a conversion is going on. The current implementation gets
one small detail wrong though. CS is only de-asserted after the SPI bus is
unlocked. This means it is possible for a different SPI device on the same
bus to send a message which would be wrongfully be addressed to the
SigmaDelta device as well. Make sure that the last SPI transfer that is
done while holding the SPI bus lock de-asserts the CS signal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <Alexandru.Ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fabrice Gasnier [Mon, 25 Mar 2019 14:49:28 +0000 (15:49 +0100)]
iio: adc: stm32-dfsdm: add PM support
Add PM and runtime PM support to STM32 DFSDM drivers:
- stm32-dfsdm-core: manage clocks.
- stm32-dfsdm-adc: restore channels configuration upon resume. Also stop
restart everything in case of buffer mode.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fabrice Gasnier [Mon, 25 Mar 2019 14:24:01 +0000 (15:24 +0100)]
iio: adc: stm32-dfsdm: improve sampling frequency accuracy
The sample frequency is driven using the oversampling ratio depending
on the SPI bus frequency.
Currently, oversampling ratio is computed by an entire division:
- spi_freq / sample_freq. This may result in inaccurate value.
Using DIV_ROUND_CLOSEST improves resulting sample frequency, which is
useful for audio that requests fixed rates (such as: 8, 16 or 32 kHz).
BTW, introduce new routine to re-factor sample frequency setting, and
move frequency accuracy message from warning to debug level.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cristian Sicilia [Sun, 24 Mar 2019 17:23:09 +0000 (18:23 +0100)]
staging: iio: adc: ad7280a: Tab alignment
Aligned some parameters.
Signed-off-by: Cristian Sicilia <sicilia.cristian@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stefan Popa [Tue, 26 Mar 2019 10:59:52 +0000 (12:59 +0200)]
MAINTAINERS: Fix the link to ad7606 dt-bindings
The devicetree bindings documentation for ad7606 should also include
the vendor prefix: ad7606.txt -> adi,ad7606.txt
Fixes:
6e33a125df66 ("dt-bindings: iio: adc: Add docs for AD7606 ADC")
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Paresh Chaudhary [Tue, 26 Mar 2019 11:18:42 +0000 (12:18 +0100)]
iio:temperature: Add MAX31856 thermocouple support
This patch adds support for Maxim MAX31856 thermocouple
temperature sensor support.
More information can be found in:
https://www.maximintegrated.com/en/ds/MAX31856.pdf
NOTE: Driver support only Comparator Mode.
Signed-off-by: Paresh Chaudhary <paresh.chaudhary@rockwellcollins.com>
Signed-off-by: Matt Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Patrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Paresh Chaudhary [Tue, 26 Mar 2019 11:18:41 +0000 (12:18 +0100)]
iio:temperature:max31856:Add device tree bind info
This patch added device tree binding info for MAX31856 driver.
Signed-off-by: Paresh Chaudhary <paresh.chaudhary@rockwellcollins.com>
Signed-off-by: Matt Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Patrick Havelange <patrick.havelange@essensium.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Patrick Havelange [Tue, 26 Mar 2019 11:18:40 +0000 (12:18 +0100)]
dt-bindings: iio/temperature: Add thermocouple types (and doc)
This patch introduces common thermocouple types used by various
temperature sensors. Also a brief documentation explaining this
"thermocouple-type" property.
Signed-off-by: Patrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andreas Klinger [Tue, 26 Mar 2019 13:39:40 +0000 (14:39 +0100)]
devantech-srf04.yaml: transform DT binding to YAML
devantech-srf04.yaml: yaml devicetree binding for iio ultrasonic
proximity driver of devantech srf04
use devantech-srf04.txt, transform binding into yaml and remove the
outdated DT documentation
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Lars-Peter Clausen [Tue, 26 Mar 2019 13:40:03 +0000 (15:40 +0200)]
iio: frequency: ad9523: Fix typo in ad9523_platform_data
Replace diff_{m1,m2} with div_{m1,m2} since they are dividers and not a
differential settings.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andy Shevchenko [Tue, 26 Mar 2019 13:47:00 +0000 (15:47 +0200)]
iio: Make possible to include driver.h first
If we put headers alphabetically sorted in the IIO driver,
the compilation will abort because of unknown type to handle.
Simple add a forward declaration of opaque struct iio_dev.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
H. Nikolaus Schaller [Mon, 18 Mar 2019 15:14:15 +0000 (16:14 +0100)]
dt-bindings: iio: add Bosch BMG160 gyroscope sensor
Define bindings for "bosch,bmg160" and "bosch,bmi055_gyro".
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
H. Nikolaus Schaller [Mon, 18 Mar 2019 15:14:14 +0000 (16:14 +0100)]
iio: gyro: bmg160: add device tree compatibility table
Add of_match_table.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Mircea Caprioru [Tue, 19 Mar 2019 14:25:20 +0000 (16:25 +0200)]
staging: iio: adc: ad7192: Use read_avail for available attributes
This patch removes the in_voltage-voltage_scale_available and
in_voltage_scale_available attributes. These are replaced with available
attributes added in info_mask_shared_by_type_available.
With this modification the iio core will be responsible with naming the
attributes thus removing the checkpatch warning related to
in_voltage-voltage_scale_available naming.
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Angus Ainslie (Purism) [Thu, 21 Mar 2019 15:40:47 +0000 (08:40 -0700)]
dt-bindings: iio: light: add vcnl4040 devicetree bindings
Document the vishay VCNL4040 devicetree bindings.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Angus Ainslie (Purism) [Thu, 21 Mar 2019 15:40:46 +0000 (08:40 -0700)]
iio: light: vcnl4000 add support for the VCNL4040 proximity and light sensor
The VCNL4040 is almost identical to the VCNL4200 as far as register
layout goes but just need to check a different ID register location.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Angus Ainslie (Purism) [Thu, 21 Mar 2019 15:40:45 +0000 (08:40 -0700)]
dt-bindings: iio: light: add vcnl4000 devicetree bindings
Document the vishay VCNL4000 devicetree bindings.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Angus Ainslie (Purism) [Thu, 21 Mar 2019 15:40:44 +0000 (08:40 -0700)]
iio: light: vcnl4000 add devicetree hooks
Add an of_match table for devicetree probing.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Angus Ainslie (Purism) [Thu, 21 Mar 2019 15:40:43 +0000 (08:40 -0700)]
iio: light: vcnl4000 use word writes instead of byte writes
The VCNL4200 datasheet says that word read and writes should be used
to access the registers.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Tested-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fabrice Gasnier [Thu, 21 Mar 2019 16:47:29 +0000 (17:47 +0100)]
iio: adc: stm32-dfsdm: claim direct mode for raw read and settings
Claim direct mode to ensure no buffer mode is in use for:
- single conversion
- sample rate setting (must be set when filter isn't enabled).
- oversampling ratio (must be set when filter isn't enabled).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fabrice Gasnier [Thu, 21 Mar 2019 16:47:28 +0000 (17:47 +0100)]
iio: adc: stm32-dfsdm: add support for buffer modes
DFSDM conversions can be launched continuously, or using various
triggers:
- by software
- hardware triggers (e.g. like in stm32-adc: TIM, LPTIM, EXTI)
- synchronously with DFSDM filter 0. e.g. for filters 1, 2
Launching conversions can be done using two methods:
a - injected:
- scan mode can be used to convert several channels each time a
trigger occurs.
- When not is scan mode, channels are converted in sequence, one upon
each trigger.
b - regular:
- supports software triggers or synchronous with filter 0
- single or continuous conversions
This patch finalizes DFSDM operating modes using IIO buffer modes:
- INDIO_BUFFER_SOFTWARE: regular continuous conversions (no trigger)
but limited to 1 channel. Users must set sampling frequency in this case.
For filters > 1, conversions can be started synchronously with filter 0.
- INDIO_BUFFER_TRIGGERED: triggered conversions uses injected mode for
launching conversions. DFSDM can use hardware triggers (e.g. STM32 timer
or lptimer), so add INDIO_HARDWARE_TRIGGERED to supported modes.
- INDIO_DIRECT_MODE: Only support DMA-based buffer modes. In case no DMA is
available, only support single conversions.
From userland perspective, to summarize various use cases:
1 - single conversion on any filter:
$ cd iio:deviceX
$ cat in_voltageY_raw
This uses regular a conversion (not continuous)
2 - Using sampling frequency without trigger (single channel, buffer)
$ cd iio:deviceX
$ echo 100 > sampling_frequency
$ echo "" > trigger/current_trigger
$ echo 1 > scan_elements/in_voltageY_en
$ echo 1 > buffer/enable
This uses regular conversion in continuous mode (Frequency is achieved
by tuning filter parameters)
3 - sync mode with filter 0: other filters can be converted when using
"st,filter0-sync" dt property. The conversions will get started at the
same time as filter 0. So for any filters > 1:
$ cd iio:deviceX
$ echo 100 > sampling_frequency
$ echo "" > trigger/current_trigger
$ echo 1 > scan_elements/in_voltageY_en
$ echo 1 > buffer/enable
Then start filter 0 as in 2 above.
4 - Using a hardware trigger (with one channel):
- check trigger, configure it:
$ cat /sys/bus/iio/devices/trigger1/name
tim6_trgo
$ echo 100 > /sys/bus/iio/devices/trigger1/sampling_frequency
- go to any filter:
$ echo 1 > scan_elements/in_voltageY_en
$ echo tim6_trgo > trigger/current_trigger
$ echo 1 > buffer/enable
This uses injected conversion as it uses a hardware trigger (without scan)
5 - Using a hardware trigger (with 2+ channel):
Same as in 4/ above, but enable two or more channels in scan_elements.
This uses injected conversion as it uses a hardware trigger (with scan mode)
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fabrice Gasnier [Thu, 21 Mar 2019 16:47:27 +0000 (17:47 +0100)]
iio: adc: stm32-dfsdm: add support for scan mode
In order to support multiple channels in buffer mode, add support for scan
mode. This is precursor patch to ease support of triggered buffer mode.
Currently, only audio uses buffer mode: Regular continuous conversions
with a single channel (per filter).
DFSDM hardware supports scan mode (only) with injected conversions.
Conversions can be launched by software (JSWSTART), trigger or
synchronously with filter 0 (e.g. JSYNC). Continuous conversion mode isn't
available for injected.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fabrice Gasnier [Thu, 21 Mar 2019 16:47:26 +0000 (17:47 +0100)]
iio: adc: stm32-dfsdm: enable hw consumer
Optionally enable IIO hw consumer, when provided (e.g. for DFSDM_IIO type).
This is precursor patch to introduce buffer modes.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fabrice Gasnier [Thu, 21 Mar 2019 16:47:25 +0000 (17:47 +0100)]
iio: adc: stm32-dfsdm: move dma slave config to start routine
Move DMA slave configuration to start routine: depending on regular or
injected mode is in use, DMA needs to read resp. RDATAR or JDATAR.
This is precursor patch to introduce injected mode (used for scan).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fabrice Gasnier [Thu, 21 Mar 2019 16:47:24 +0000 (17:47 +0100)]
iio: adc: stm32-dfsdm: move dma enable from start_conv() to start_dma()
Move DMA enable (e.g. set RDMAEN bit) away from start_conv() that is used
for both buffer and single conversions. Thus, single conv rely on
interrupt, not dma.
Note: take care to prepare all DMA stuff and set RDMAEN before starting
filter (can be set only when DFEN=0).
This is precursor patch to ease support of triggered buffer mode.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fabrice Gasnier [Thu, 21 Mar 2019 16:47:23 +0000 (17:47 +0100)]
iio: adc: stm32-dfsdm: continuous mode depends on current mode
DFSDM regular continuous mode usage depends on current mode (not DMA):
- for single conversion, RCONT doesn't need to be set.
- for buffer mode, RCONT has to be set (e.g. INDIO_BUFFER_SOFTWARE
used by audio currently).
This is related to filter configuration, move it to relevant routine.
This is precursor patch to ease support of triggered buffer mode.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fabrice Gasnier [Thu, 21 Mar 2019 16:47:22 +0000 (17:47 +0100)]
iio: adc: stm32-dfsdm: make spi_master_freq more accurate
Current ckout divider may be set to a value that makes ckout to exceed
spi-max-frequency. Rather use lower value (e.g. round up divider when
ckout isn't accurate).
Also when the SPI clock isn't accurate, 'spi_master_freq' is filled in
with expected frequency. Use computed value instead to be more accurate:
- e.g. source clock / (CKOUTDIV + 1)
Enforce checks on the divider: ckoutdiv range can be from 1-255 to provide
divider of 2-256.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Marcelo Schmitt [Thu, 21 Mar 2019 18:42:13 +0000 (15:42 -0300)]
staging: iio: ad5933: change attributes to match ABI
Change device attributes' names to match ABI documentation. Names were
chosen such that they tend to be similar to existing ABI so it should
be easier to standardize them when necessary.
Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Vladimir Petrigo [Thu, 21 Mar 2019 21:15:28 +0000 (00:15 +0300)]
iio: adc: ad7780: Add parentheses to macros
- Fix CHECK Macro argument 'wordsize' may be better as '(wordsize)' to avoid precedence issues
Slightly modified by Jonathan to take into account the staging graduation
and a copy and paste version of the same item on the following line.
Signed-off-by: Vladimir Petrigo <vladimir.petrigo@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Alexandru Ardelean [Fri, 22 Mar 2019 20:44:42 +0000 (22:44 +0200)]
iio: imu: adis16400: move adis16400.h into adis16400.c
Final part of the re-organization. Move the `adis16400.h` into
`adis16400.c` since it no longer needs to be shared among other files.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Alexandru Ardelean [Fri, 22 Mar 2019 20:44:41 +0000 (22:44 +0200)]
iio: imu: adis16400: rename adis16400_core.c -> adi16400.c
This change does a simple 1-to-1 rename of the adis16400_core.c file. Now
that the `adis16400_buffer.c` file was removed, everything can be moved
into a single driver file.
But first, this rename.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Alexandru Ardelean [Fri, 22 Mar 2019 20:44:40 +0000 (22:44 +0200)]
iio: imu: adis16400: move burst logic to ADIS lib
This change has been done separately, so that it's easier to visualize the
changed logic in the adis_scan_update() function.
Most of the function in this `adis16400_update_scan_mode()` that deals with
burst-mode will be re-used in the ADIS16480, but with different parameters.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Alexandru Ardelean [Fri, 22 Mar 2019 20:44:39 +0000 (22:44 +0200)]
iio: imu: adis: generalize burst mode support
Some variants in the ADIS16400 family support burst mode. This mechanism is
implemented in the `adis16400_buffer.c` file.
Some variants in ADIS16480 are also adding burst mode, which is
functionally similar to ADIS16400, but with different parameters. To get
there, a `adis_burst` struct is added to parametrize certain bits of the
SPI communication to setup: the register that triggers burst-mode, and the
extra-data-length that needs be accounted for when building the bust-length
buffer.
The trigger handler cannot be made generic, since it's very specific to
each ADIS164XX family.
A future enhancement of this `adis_burst` mode will be the possibility to
enable/disable burst-mode. For the ADIS16400 family it's hard-coded to on
by default. But for ADIS16480 there will be a need to disable this.
When that will be implemented, both ADIS16400 & ADIS16480 will have the
burst-mode enable-able/disable-able.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Alexandru Ardelean [Fri, 22 Mar 2019 20:44:38 +0000 (22:44 +0200)]
iio: imu: adis16400: move trigger handler into adis16400_core
The trigger handler for the ADIS16400 is very different from the generic
one in the ADIS library. Keeping it in a separate file won't make much
sense once the update_scan_mode function will be made more generic and
moved into the ADIS library.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cristian Sicilia [Sat, 23 Mar 2019 19:21:49 +0000 (20:21 +0100)]
staging: iio: adc: ad7280a: Remove CamelCase notation
Fix CamelCase naming.
Signed-off-by: Cristian Sicilia <sicilia.cristian@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cristian Sicilia [Sat, 23 Mar 2019 19:21:45 +0000 (20:21 +0100)]
staging: iio: adc: ad7280a: Adding temp var to improve readability
Creating a temporary variable to improve readability
Signed-off-by: Cristian Sicilia <sicilia.cristian@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cristian Sicilia [Sat, 23 Mar 2019 19:21:42 +0000 (20:21 +0100)]
staging: iio: adc: ad7280a: Avoid precedence issues in macro
Enclosing parameter with parenthesis due to avoid
possible precedence issue.
Signed-off-by: Cristian Sicilia <sicilia.cristian@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andreas Klinger [Sun, 17 Mar 2019 20:38:29 +0000 (21:38 +0100)]
MAINTAINERS: add maintainer for maxbotix ultrasonic driver
add a maintainer for the newly created ultrasonic driver family of maxbotix
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andreas Klinger [Sun, 17 Mar 2019 20:38:03 +0000 (21:38 +0100)]
mb1232.c: add distance iio sensor with i2c
Add I2CXL-MaxSonar ultrasonic distance sensors of types mb1202, mb1212,
mb1222, mb1232, mb1242, mb7040, mb7137 using an i2c interface
Implemented functionality:
- reading the distance via in_distance_raw
- buffered mode with trigger
- make use of interrupt to announce completion of ranging
Add mb1232 driver to Kconfig and Makefile
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andreas Klinger [Sun, 17 Mar 2019 20:35:27 +0000 (21:35 +0100)]
dt-bindings: maxbotix,mb1232: Add MaxBotix i2c ultrasonic rangers
Add doc for dt binding maxbotix,mb1232. This binding is for MaxBotix
I2CXL-MaxSonar ultrasonic rangers which share a common i2c interface.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andreas Klinger [Sun, 17 Mar 2019 20:35:00 +0000 (21:35 +0100)]
dt-bindings: Add vendor prefix for MaxBotix
Add MaxBotix, which is a vendor of ultrasonic rangers in different
varieties and interfaces.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Kangjie Lu [Sat, 16 Mar 2019 22:08:33 +0000 (17:08 -0500)]
iio: hmc5843: fix potential NULL pointer dereferences
devm_regmap_init_i2c may fail and return NULL. The fix returns
the error when it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Marcelo Schmitt [Sat, 16 Mar 2019 15:07:32 +0000 (12:07 -0300)]
staging: iio: ad5933: add ABI documentation
Add an ABI documentation for the ad5933 driver.
Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Marcelo Schmitt [Sat, 16 Mar 2019 15:07:18 +0000 (12:07 -0300)]
staging: iio: ad5933: change help rule message
Remove the previous comment about direct access via sysfs which would
lead one think ad5933 driver has limitations it actually doesn't.
Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Marcelo Schmitt [Sat, 16 Mar 2019 15:07:03 +0000 (12:07 -0300)]
staging: iio: ad5933: add SPDX identifier
Add SPDX identifier of GPL-2.0 for the ad5933 driver.
Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Marcelo Schmitt [Sat, 16 Mar 2019 15:06:50 +0000 (12:06 -0300)]
staging: iio: ad5933: organize includes
Organize includes to list them in lexicographic order.
Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Marcelo Schmitt [Sat, 16 Mar 2019 15:06:18 +0000 (12:06 -0300)]
staging: iio: ad5933: change multi-line comment style
Make multi-line comments compliant with the preferred code style.
Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Renato Lui Geh [Sat, 16 Mar 2019 02:16:13 +0000 (23:16 -0300)]
staging: iio: ad7780: add device tree binding
Adds a device tree binding for the ad7780 driver.
Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Renato Lui Geh [Sat, 16 Mar 2019 02:15:55 +0000 (23:15 -0300)]
staging: iio: ad7780: moving ad7780 out of staging
Move ad7780 ADC driver out of staging and into the mainline.
The ad7780 is a sigma-delta analog to digital converter. This driver provides
reading voltage values and status bits from both the ad778x and ad717x series.
Its interface also allows writing on the FILTER and GAIN GPIO pins on the
ad778x.
Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Signed-off-by: Giuliano Belinassi <giuliano.belinassi@usp.br>
Co-developed-by: Giuliano Belinassi <giuliano.belinassi@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Renato Lui Geh [Sat, 16 Mar 2019 02:15:26 +0000 (23:15 -0300)]
staging: iio: ad7780: add new copyright holder
This patch adds a new copyright holder to the ad7780 driver.
Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Renato Lui Geh [Sat, 16 Mar 2019 02:15:13 +0000 (23:15 -0300)]
staging: iio: ad7780: add SPDX identifier
Add SPDX identifier (GPL-2.0) to the AD7780 driver.
Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Renato Lui Geh [Sat, 16 Mar 2019 02:14:59 +0000 (23:14 -0300)]
staging: iio: ad7780: move regulator to after GPIO init
To maintain consistency between ad7780_probe and ad7780_remove orders,
regulator initialization has been moved to after GPIO initializations.
Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Renato Lui Geh [Sat, 16 Mar 2019 02:14:27 +0000 (23:14 -0300)]
staging:iio:ad7780: add chip ID values and mask
The ad7780 supports both the ad778x and ad717x families. Each chip has
a corresponding ID. This patch provides a mask for extracting ID values
from the status bits and also macros for the correct values for the
ad7170, ad7171, ad7780 and ad7781.
Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Renato Lui Geh [Sat, 16 Mar 2019 02:14:14 +0000 (23:14 -0300)]
staging: iio: ad7780: set pattern values and masks directly
The AD7780 driver contains status pattern bits designed for checking
whether serial transfers have been correctly performed. Pattern macros
were previously generated through bit fields. This patch sets good
pattern values directly and masks through GENMASK.
Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Renato Lui Geh [Sat, 16 Mar 2019 02:13:42 +0000 (23:13 -0300)]
staging: iio: ad7780: add filter reading to ad778x
This patch adds the new feature of reading the filter odr value for
ad778x chips. This value is stored in the chip's state struct whenever a
read or write call is performed on the chip's driver.
This feature requires sharing SAMP_FREQ. Since the ad717x does not have
a filter option, the driver only shares the relevant info mask for the
ad778x family.
Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Renato Lui Geh [Sat, 16 Mar 2019 02:13:13 +0000 (23:13 -0300)]
staging: iio: ad7780: add gain reading to ad778x
This patch adds a new functionality of reading gain values from the
ad778x chips. This value is stored in the chip's state struct and is
updated whenever a read or write call is performed on the driver.
Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Renato Lui Geh [Sat, 16 Mar 2019 02:12:53 +0000 (23:12 -0300)]
staging: iio: ad7780: add missing switch default case
This patch simply adds a missing switch default case in read_raw.
Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>