dt-bindings: clock: add SM6375 QCOM global clock bindings

Add device tree bindings for global clock controller for SM6375 SoCs.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220921001303.56151-2-konrad.dybcio@somainline.org

clk: qcom: alpha: Add support for programming the PLL_FSM_LEGACY_MODE bit

This is used on at least SM6375 and its variations.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220921001303.56151-1-konrad.dybcio@somainline.org

clk: qcom: gcc-sc7280: Update the .pwrsts for usb gdscs

The USB controllers on sc7280 do not retain the state when
the system goes into low power state and the GDSCs are
turned off. This results in the controllers reinitializing and
re-enumerating all the connected devices (resulting in additional
delay while coming out of suspend)
Fix this by updating the .pwrsts for the USB GDSCs so they only
transition to retention state in low power.
Since sc7280 only supports cx (parent of usb gdscs) Retention, there
are no cxcs offsets mentioned in order to support the Retention
state.

Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220920111517.10407-3-quic_rjendra@quicinc.com

clk: qcom: gcc-sc7180: Update the .pwrsts for usb gdsc

The USB controller on sc7180 does not retain the state when
the system goes into low power state and the GDSC is
turned off. This results in the controller reinitializing and
re-enumerating all the connected devices (resulting in additional
delay while coming out of suspend)
Fix this by updating the .pwrsts for the USB GDSC so it only
transitions to retention state in low power.
Since sc7180 only supports cx (parent of usb gdsc) Retention, there
are no cxcs offsets mentioned in order to support the Retention
state.

Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220920111517.10407-2-quic_rjendra@quicinc.com

clk: qcom: gdsc: Fix the handling of PWRSTS_RET support

GDSCs cannot be transitioned into a Retention state in SW.
When either the RETAIN_MEM bit, or both the RETAIN_MEM and
RETAIN_PERIPH bits are set, and the GDSC is left ON, the HW
takes care of retaining the memory/logic for the domain when
the parent domain transitions to power collapse/power off state.

On some platforms where the parent domains lowest power state
itself is Retention, just leaving the GDSC in ON (without any
RETAIN_MEM/RETAIN_PERIPH bits being set) will also transition
it to Retention.

The existing logic handling the PWRSTS_RET seems to set the
RETAIN_MEM/RETAIN_PERIPH bits if the cxcs offsets are specified
but then explicitly turns the GDSC OFF as part of _gdsc_disable().
Fix that by leaving the GDSC in ON state.

Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220920111517.10407-1-quic_rjendra@quicinc.com

clk: qcom: Add SC8280XP GPU clock controller

Add driver for the GPU clock controller in the Qualcomm SC8280XP
platform.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
[bjorn: Included kernel.h and lower-cased hex numbers]
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220926173025.4747-3-quic_bjorande@quicinc.com

dt-bindings: clock: Add Qualcomm SC8280XP GPU binding

Add compatible for the Qualcomm SC8280XP GPU.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220926173025.4747-2-quic_bjorande@quicinc.com

clk: qcom: smd: Add SM6375 clocks

Add support for controlling SMD RPM clocks on SM6375.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220921004458.151842-3-konrad.dybcio@somainline.org

dt-bindings: clock: qcom: rpmcc: Add BIMC_FREQ_LOG

Add the missing definition for the aforementioned clock.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220921004458.151842-2-konrad.dybcio@somainline.org

dt-bindings: clock: qcom,rpmcc: Add compatible for SM6375

Add a compatible for RPMCC on SM6375.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220921004458.151842-1-konrad.dybcio@somainline.org

clk: qcom: rpmhcc: add sdm670 clocks

The Snapdragon 670 uses the RPMh mailbox for most of the clocks used in
SDM845 but omits two. Add clock data for SDM670 so the driver doesn't fail
to resolve a clock.

Link: https://android.googlesource.com/kernel/msm/+/443bd8d6e2cf54698234c752e6de97b4b8a528bd%5E%21/#F7
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220920223734.151135-3-mailingradian@gmail.com

dt-bindings: clock: add rpmhcc bindings for sdm670

The Snapdragon 670 uses the RPMh mailbox for some clocks. Document its
support.

Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220920223734.151135-2-mailingradian@gmail.com

dt-bindings: clock: qcom,a53pll: replace maintainer

Emails to codeaurora.org bounce ("Recipient address rejected:
undeliverable address: No such user here.").

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220924081329.15141-1-krzysztof.kozlowski@linaro.org

clk: qcom: Merge alt alpha plls for qcm2260, sm6115

The qcom2260 and sm6115 GCC drivers use a common modified DEFAULT and
BRAMMO alpha pll offsets. Move these common offsets to the shared place
to avoid duplication. The new layouts have a suffix EVO similar to LUCID
and RIVIAN.

Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220830075620.974009-4-iskren.chernev@gmail.com

clk: qcom: gcc-sm6115: Move alpha pll bramo overrides

sm6115 uses a modified default and bramo alpha pll offsets. Put them in
the same place for consistency.

Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220830075620.974009-3-iskren.chernev@gmail.com

clk: qcom: gcc-sm6115: Override default Alpha PLL regs

The DEFAULT and BRAMMO PLL offsets are non-standard in downstream, but
currently only BRAMMO ones are overridden. Override DEFAULT ones too.

A very similar thing is happening in gcc-qcm2290 driver.

Fixes: cbe63bfdc54f ("clk: qcom: Add Global Clock controller (GCC) driver for SM6115")
Signed-off-by: Adam Skladowski <a_skl39@protonmail.com>
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220830075620.974009-2-iskren.chernev@gmail.com

clk: qcom: Add support for Display Clock Controller on SM8450

Add support for the dispcc on Qualcomm SM8450 platform.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220908222850.3552050-4-dmitry.baryshkov@linaro.org

clk: qcom: alpha-pll: add support for power off mode for lucid evo PLL

PLLs can be kept in standby (default configuration) or in off mode
when disabled during power collapse. Hence add support for pll
disable off mode for lucid evo PLL.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220908222850.3552050-3-dmitry.baryshkov@linaro.org

dt-bindings: clock: qcom: add bindings for dispcc on SM8450

Add device tree bindings for the display clock controller on Qualcomm
SM8450 platform.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220908222850.3552050-2-dmitry.baryshkov@linaro.org

clk: qcom: Add display clock controller driver for SM6115

Add support for the display clock controller found in SM6115/SM4250
based devices. This clock controller feeds the Multimedia Display
SubSystem (MDSS).
This driver is based upon one submitted for QCM2290.

Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220911164635.182973-3-a39.skl@gmail.com

dt-bindings: clock: add QCOM SM6115 display clock bindings

Add device tree bindings for display clock controller for
Qualcomm Technology Inc's SM6115 SoC.

Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[bjorn: Minor fix of binding description]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220911164635.182973-2-a39.skl@gmail.com

clk: qcom: gcc-sc7280: Update the .pwrsts for PCIe GDSC

Enabling PCIe GDSC retention to ensure controller and its
dependent clocks won't go down during system suspend.
Update the .pwrsts for PCIe GDSC so it only transitions
to RET in low power.

Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1663669347-29308-6-git-send-email-quic_krichai@quicinc.com

clk: qcom: lpass: Fix lpass audiocc probe

Change the qcom_cc_probe_by_index() call to qcom_cc_really_probe()
to avoid remapping of memory region for index 0, which is already
being done through qcom_cc_map().

Fixes: 7c6a6641c2 ("clk: qcom: lpass: Add support for resets & external mclk for SC7280")
Signed-off-by: Satya Priya <quic_c_skakit@quicinc.com>
Reviewed-by: Neil Armstrong <neil.armstrong@baylibre.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1663673683-7018-1-git-send-email-quic_c_skakit@quicinc.com

clk: qcom: apss-ipq-pll: add support for IPQ8074

Add support for IPQ8074 since it uses the same PLL setup, however it uses
slightly different Alpha PLL config.

Alpha PLL config was obtained by dumping PLL registers from a running
device.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220818220628.339366-7-robimarko@gmail.com

clk: qcom: apss-ipq-pll: update IPQ6018 Alpha PLL config

Update the IPQ6018 Alpha PLL config to the latest one from the downstream
5.4 kernel[1].

This one should match the production SoC-s.

Tested on IPQ6018 CP01-C1 reference board.

[1] https://git.codelinaro.org/clo/qsdk/oss/kernel/linux-ipq-5.4/-/blob/NHSS.QSDK.12.1.r4/drivers/clk/qcom/apss-ipq-pll.c#L41

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220818220628.339366-6-robimarko@gmail.com

clk: qcom: apss-ipq-pll: use OF match data for Alpha PLL config

Convert the driver to use OF match data for providing the Alpha PLL config
per compatible.
This is required for IPQ8074 support since it uses a different Alpha PLL
config.

While we are here rename "ipq_pll_config" to "ipq6018_pll_config" to make
it clear that it is for IPQ6018 only.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220818220628.339366-5-robimarko@gmail.com

dt-bindings: clock: qcom,a53pll: add IPQ8074 compatible

Add IPQ8074 compatible to A53 PLL bindings.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220818220628.339366-4-robimarko@gmail.com

clk: qcom: apss-ipq6018: mark apcs_alias0_core_clk as critical

While fixing up the driver I noticed that my IPQ8074 board was hanging
after CPUFreq switched the frequency during boot, WDT would eventually
reset it.

So mark apcs_alias0_core_clk as critical since its the clock feeding the
CPU cluster and must never be disabled.

Fixes: 5e77b4ef1b19 ("clk: qcom: Add ipq6018 apss clock controller")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220818220628.339366-3-robimarko@gmail.com

clk: qcom: apss-ipq6018: fix apcs_alias0_clk_src

While working on IPQ8074 APSS driver it was discovered that IPQ6018 and
IPQ8074 use almost the same PLL and APSS clocks, however APSS driver is
currently broken.

More precisely apcs_alias0_clk_src is broken, it was added as regmap_mux
clock.
However after debugging why it was always stuck at 800Mhz, it was figured
out that its not regmap_mux compatible at all.
It is a simple mux but it uses RCG2 register layout and control bits, so
utilize the new clk_rcg2_mux_closest_ops to correctly drive it while not
having to provide a dummy frequency table.

While we are here, use ARRAY_SIZE for number of parents.

Tested on IPQ6018-CP01-C1 reference board and multiple IPQ8074 boards.

Fixes: 5e77b4ef1b19 ("clk: qcom: Add ipq6018 apss clock controller")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220818220628.339366-2-robimarko@gmail.com

clk: qcom: clk-rcg2: add rcg2 mux ops

An RCG may act as a mux that switch between 2 parents.
This is the case on IPQ6018 and IPQ8074 where the APCS core clk that feeds
the CPU cluster clock just switches between XO and the PLL that feeds it.

Add the required ops to add support for this special configuration and use
the generic mux function to determine the rate.

This way we dont have to keep a essentially dummy frequency table to use
RCG2 as a mux.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220818220628.339366-1-robimarko@gmail.com

clk: qcom: lcc-ipq806x: use ARRAY_SIZE for num_parents

Use ARRAY_SIZE for num_parents instead of raw number to prevent any
confusion/mistake.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220724182329.9891-4-ansuelsmth@gmail.com

clk: qcom: lcc-ipq806x: convert to parent data

Convert lcc-ipq806x driver to parent_data API.
Change parent_name for pll4 to pxo_board to prepare the future to
eventually drop the double pxo board clk.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220724182329.9891-3-ansuelsmth@gmail.com

clk: qcom: lcc-ipq806x: add reset definition

Add reset definition for lcc-ipq806x.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220724182329.9891-2-ansuelsmth@gmail.com

dt-bindings: clock: add pcm reset for ipq806x lcc

Add pcm reset define for ipq806x lcc.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220724182329.9891-1-ansuelsmth@gmail.com

clk: qcom: cpu-8996: use constant mask for pmux

Both pmux instances share the same width and shift. Specify the mask at
compile time to simplify functions.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220714100351.1834711-7-dmitry.baryshkov@linaro.org

clk: qcom: cpu-8996: don't store parents in clk_cpu_8996_pmux

Don't store pointers to parents in struct clk_cpu_8996_pmux. Instead use
clk_hw_get_parent_by_index to fetch them.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220714100351.1834711-6-dmitry.baryshkov@linaro.org

clk: qcom: cpu-8996: move ACD logic to clk_cpu_8996_pmux_determine_rate

Rather than telling everybody that we are using PLL as a parent (and
using ACD clock instead) properly select ACD as a pmux parent clock.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220714100351.1834711-5-dmitry.baryshkov@linaro.org

clk: qcom: cpu-8996: declare ACD clocks

To simplify the code, define 1:1 fixed factor clocks to represent the
ACD pmux parent.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220714100351.1834711-4-dmitry.baryshkov@linaro.org

clk: qcom: cpu-8996: switch to devm_clk_notifier_register

Switch to using devres-managed version of clk_notifier_register(). This
allows us to drop driver's remove() callback.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220714100351.1834711-3-dmitry.baryshkov@linaro.org

clk: qcom: msm8996-cpu: Use parent_data/_hws for all clocks

Replace parent_names in PLLs, secondary muxes and primary muxes with
parent_data. For primary muxes there were never any *cl_pll_acd clocks,
so instead of adding them, put the primary PLLs in both PLL_INDEX and
ACD_INDEX, then make sure ACD_INDEX is always picked over PLL_INDEX when
setting parent since we always want ACD when using the primary PLLs.

Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
[DB: switch to parent_hws for pmux clocks]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220714100351.1834711-2-dmitry.baryshkov@linaro.org

dt-bindings: clock: qcom,msm8996-apcc: Fix clocks

The clocks currently listed in clocks and clock-names are the ones
supplied by this clock controller, not the ones it consumes. Replace
them with the only clock it consumes - the on-board oscillator (XO),
and make the properties required.

Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220621160621.24415-6-y.oudjana@protonmail.com

clk: qcom: msm8996-cpu: Convert secondary muxes to clk_regmap_mux

There is nothing special about the secondary muxes, unlike the
primary muxes which need some extra logic to handle ACD and
switching between primary PLL and secondary mux sources. Turn
them into clk_regmap_mux and rename cpu_clk_msm8996_mux into
cpu_clk_msm8996_pmux to make it specific to primary muxes.

Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220621160621.24415-5-y.oudjana@protonmail.com

clk: qcom: msm8996-cpu: Unify cluster order

The power cluster comes before the performance cluster. Make
everything in the driver follow this order.

Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220621160621.24415-4-y.oudjana@protonmail.com

clk: qcom: msm8996-cpu: Statically define PLL dividers

This will allow for adding them to clk_parent_data arrays
in an upcoming patch.

Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220621160621.24415-3-y.oudjana@protonmail.com

clk: qcom: msm8996-cpu: Rename DIV_2_INDEX to SMUX_INDEX

The parent at this index is the secondary mux, which can connect
not only to primary PLL/2 but also to XO. Rename the index to SMUX_INDEX
to better reflect the parent.

Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220621160621.24415-2-y.oudjana@protonmail.com

clk: qcom: smd-rpm: Add clocks for MSM8909

MSM8909 has mostly the same as clocks in RPM as MSM8916,
but additionally the QPIC clock for the NAND flash controller.

Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220706134132.3623415-7-stephan.gerhold@kernkonzept.com

dt-bindings: clock: qcom,rpmcc: Add MSM8909

Document the "qcom,rpmcc-msm8909" compatible for the clocks available
via the RPM on the MSM8909 SoC.

Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220706134132.3623415-6-stephan.gerhold@kernkonzept.com

clk: qcom: gcc-msm8909: Increase delay for USB PHY reset

The USB PHY on MSM8909 works with the driver used on MSM8916
(phy-qcom-usb-hs.c). When turning the PHY on/off it is first reset
using the standard reset controller API. On MSM8916 the reset is
provided by the USB driver (ci_hdrc_msm_por_reset() in ci_hdrc_msm.c).

While this seems to work on MSM8909 as well, the Qualcomm Linux sources
suggest that the PHY should be reset using the GCC_USB2_HS_PHY_ONLY_BCR
register instead. In general this is easy to set up in the device tree,
thanks to the standard reset controller API.

However, to conform to the specifications of the PHY the reset signal
should be asserted for at least 10 us. This is handled correctly on
MSM8916 in ci_hdrc_msm_por_reset(), but not within the GCC driver.

Fix this by making use of the new "udelay" field of qcom_reset_map
and set a delay of ~15 us between the assertion/deassertion of the
USB PHY reset signal.

Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220706134132.3623415-5-stephan.gerhold@kernkonzept.com

clk: qcom: reset: Allow specifying custom reset delay

The amount of time required between asserting and deasserting the reset
signal can vary depending on the involved hardware component. Sometimes
1 us might not be enough and a larger delay is necessary to conform to
the specifications.

Usually this is worked around in the consuming drivers, by replacing
reset_control_reset() with a sequence of reset_control_assert(), waiting
for a custom delay, followed by reset_control_deassert().

However, in some cases the driver making use of the reset is generic and
can be used with different reset controllers. In this case the reset
time requirement is better handled directly by the reset controller
driver.

Make this possible by adding an "udelay" field to the qcom_reset_map
that allows setting a different reset delay (in microseconds).

Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220706134132.3623415-4-stephan.gerhold@kernkonzept.com

clk: qcom: Add driver for MSM8909 GCC

The Global Clock Controller (GCC) in the MSM8909 SoC provides clocks,
resets and power domains for the various hardware blocks in the SoC.
Add a driver for it to make it possible to enable additional
functionality for the SoC.

Work on this driver was originally started independently by Dominik,
I picked it up and added missing clocks/resets, as well as various
cleanup to bring it into shape for mainline.

Co-developed-by: Dominik Kobinski <dominikkobinski314@gmail.com>
Signed-off-by: Dominik Kobinski <dominikkobinski314@gmail.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220706134132.3623415-3-stephan.gerhold@kernkonzept.com

dt-bindings: clock: Add schema for MSM8909 GCC

The Global Clock Controller (GCC) in the MSM8909 SoC provides clocks,
resets and power domains for the various hardware blocks in the SoC.
Add a DT schema to describe it, similar to other Qualcomm SoCs.

Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220706134132.3623415-2-stephan.gerhold@kernkonzept.com

clk: qcom: mmcc-msm8960: use parent_hws/_data instead of parent_names

Convert the clock driver to specify parent data rather than parent
names, to actually bind using 'clock-names' specified in the DTS rather
than global clock names. Use parent_hws where possible to refer parent
clocks directly, skipping the lookup.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-10-dmitry.baryshkov@linaro.org

clk: qcom: mmcc-msm8960: move clock parent tables down

Move clock parent tables down, after the PLL declrataions, so that we
can use pll hw clock fields in the next commit.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-9-dmitry.baryshkov@linaro.org

clk: qcom: mmcc-msm8960: use ARRAY_SIZE instead of specifying num_parents

Use ARRAY_SIZE() instead of manually specifying num_parents. This makes
adding/removing entries to/from parent_data easy and errorproof.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-8-dmitry.baryshkov@linaro.org

clk: qcom: lcc-msm8960: use parent_hws/_data instead of parent_names

Convert the clock driver to specify parent data rather than parent
names, to actually bind using 'clock-names' specified in the DTS rather
than global clock names. Use parent_hws where possible to refer parent
clocks directly, skipping the lookup.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-7-dmitry.baryshkov@linaro.org

clk: qcom: lcc-msm8960: use macros to implement mi2s clocks

Split and extend existing CLK_AIF_OSR_DIV macro to implement mi2s
clocks. This simplifies the driver and removes extra code duplication.

The clock mi2s_div_clk used .enable_reg/.enable_bit, however these
fields are not used with by the clk_regmap_div_ops, thus they are
silently dropped. Clock enablement is handled in the mi2s_bit_div_clk
clock.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-6-dmitry.baryshkov@linaro.org

clk: qcom: gcc-msm8960: use parent_hws/_data instead of parent_names

Convert the clock driver to specify parent data rather than parent
names, to actually bind using 'clock-names' specified in the DTS rather
than global clock names. Use parent_hws where possible to refer parent
clocks directly, skipping the lookup.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-5-dmitry.baryshkov@linaro.org

clk: qcom: gcc-msm8960: use ARRAY_SIZE instead of specifying num_parents

Use ARRAY_SIZE() instead of manually specifying num_parents. This makes
adding/removing entries to/from parent_data easy and errorproof.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-4-dmitry.baryshkov@linaro.org

dt-bindings: clocks: qcom,mmcc: define clocks/clock-names for MSM8960

Define clock/clock-names properties of the MMCC device node to be used
on MSM8960/APQ8064 platform.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-3-dmitry.baryshkov@linaro.org

dt-bindings: clocks: qcom,gcc-apq8064: define clocks/-names properties

Define clock/clock-names properties of the GCC device node to be
used on MSM8960/APQ8064 platforms.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-2-dmitry.baryshkov@linaro.org

clk: qcom: clk-rpmh: Remove redundant if statement

By the clk framework already reference counts prepare/unprepare,
this if statement should be never true.

Signed-off-by: Li Zhengyu <lizhengyu3@huawei.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20220613063327.89320-1-lizhengyu3@huawei.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

clk: qcom: gcc-sdm845: add sdm670 global clock data

The Snapdragon 670 adds and removes some clocks, adds new frequencies, and
adds a new GPLL (Global Phase-Locked Loop) in reference to SDM845, while
also removing some GDSCs. Despite these differences, there are many
similarities with SDM670. Add data for SDM670 in the driver for SDM845 to
reuse the most of the clock data.

Advantages and disadvantages of this approach:
 + maintenance applies to both sdm670 and sdm845 by default
 + less duplicate code (clocks) means smaller distro/pre-built kernels
   with all drivers enabled
 - clocks for both SoC's must be compiled if the user wants clocks for one
   specific SoC (both or none)
 - additional testing needed for sdm845 devices

Link: https://android.googlesource.com/kernel/msm/+/443bd8d6e2cf54698234c752e6de97b4b8a528bd%5E%21/#F10
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220914013922.198778-4-mailingradian@gmail.com

clk: qcom: gcc-sdm845: use device tree match data

This driver will support more than one SoC's set of clocks, and set of
GDSCs. This behavior would be unclean with hard-coded static variables.
Support it by grabbing clocks, GDSCs, and BCRs in the match data.

Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220914013922.198778-3-mailingradian@gmail.com

dt-bindings: clock: gcc-sdm845: add sdm670 global clocks

The Snapdragon 670 clocks will be added into the sdm845 gcc driver. Most
of the new clocks, GDSCs, and resets already have reserved IDs but there
are some resources that don't. Add the new clock from Snapdragon 670 and
document the differences between the SoC parent clocks.

Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220914013922.198778-2-mailingradian@gmail.com

clk: qcom: a53-pll: convert to use parent_data rather than parent_names

Change a53-pll driver to use clk_parent_data rather than always looking
up the xo clock in the system clock list.

Note, this change also switches the a53-pll from the global `xo' clock
to the `xo_board', the clock that is specified as the `xo' clock in the
DT file.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220909103137.3727830-1-dmitry.baryshkov@linaro.org

clk: qcom: gcc-msm8660: use parent_hws/_data instead of parent_names

Convert the clock driver to specify parent data rather than parent
names, to actually bind using 'clock-names' specified in the DTS rather
than global clock names. Use parent_hws where possible to refer parent
clocks directly, skipping the lookup.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220909105136.3733919-4-dmitry.baryshkov@linaro.org

clk: qcom: gcc-msm8660: use ARRAY_SIZE instead of specifying num_parents

Use ARRAY_SIZE() instead of manually specifying num_parents. This makes
adding/removing entries to/from parent_data easy and errorproof.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220909105136.3733919-3-dmitry.baryshkov@linaro.org

dt-bindings: clock: qcom,gcc-msm8660: separate GCC bindings for MSM8660

Create a separate DT bindings for Global Clock Controller on MSM8660
platform.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220909105136.3733919-2-dmitry.baryshkov@linaro.org

clk: qcom: sm6115: Select QCOM_GDSC

While working on the Fxtec Pro1X device, this error shows up with
my own minimal configuration:

gcc-sm6115: probe of 1400000.clock-controller failed with error -38

The clock driver depends on CONFIG_QCOM_GDSC and after enabling
that, the driver probes successfully.

Signed-off-by: Dang Huynh <danct12@riseup.net>
Fixes: cbe63bfdc54f ("clk: qcom: Add Global Clock controller (GCC)
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220910170207.1592220-1-danct12@riseup.net

clk: qcom: lpass: Add support for resets & external mclk for SC7280

The clock gating control for TX/RX/WSA core bus clocks would be required
to be reset(moved from hardware control) from audio core driver. Thus
add the support for the reset clocks.

Update the lpass_aon_cc_main_rcg_clk_src ops to park the RCG at XO after
disable as this clock signal is used by hardware to turn ON memories in
LPASS. Also add the external mclk to interface external MI2S.

Fixes: a9dd26639d05 ("clk: qcom: lpass: Add support for LPASS clock controller for SC7280")
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1662005846-4838-6-git-send-email-quic_c_skakit@quicinc.com

clk: qcom: lpass: Handle the regmap overlap of lpasscc and lpass_aon

Move registration of lpass_q6ss_ahbm_clk and lpass_q6ss_ahbs_clk to
lpass_aon_cc_sc7280_probe and register them only if "qcom,adsp-pil-mode"
is enabled in the lpass_aon DT node.

Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Signed-off-by: Satya Priya <quic_c_skakit@quicinc.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1662005846-4838-3-git-send-email-quic_c_skakit@quicinc.com

Merge branch '1662005846-4838-1-git-send-email-quic_c_skakit@quicinc.com' into clk-for-6.1

dt-bindings: clock: Add support for external MCLKs for LPASS on SC7280

Support external mclk to interface external MI2S clocks for SC7280.

Fixes: 4185b27b3bef ("dt-bindings: clock: Add YAML schemas for LPASS clocks on SC7280")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1662005846-4838-5-git-send-email-quic_c_skakit@quicinc.com

dt-bindings: clock: Add resets for LPASS audio clock controller for SC7280

Add support for LPASS audio clock gating for RX/TX/SWA core bus clocks
for SC7280. Update reg property min/max items in YAML schema.

Fixes: 4185b27b3bef ("dt-bindings: clock: Add YAML schemas for LPASS clocks on SC7280")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1662005846-4838-4-git-send-email-quic_c_skakit@quicinc.com

dt-bindings: clock: Add "qcom,adsp-pil-mode" property

When this property is set, the remoteproc is used to boot the
LPASS and therefore lpass_q6ss_ahbm_clk and lpass_q6ss_ahbs_clk
clocks would be used to bring LPASS out of reset and the rest of
the lpass clocks would be controlled directly by the remoteproc.

This is a cleanup done to handle overlap of regmap of
lpasscc and lpass_aon blocks.

Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Signed-off-by: Satya Priya <quic_c_skakit@quicinc.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1662005846-4838-2-git-send-email-quic_c_skakit@quicinc.com

clk: qcom: gcc-sdm660: Use floor ops for SDCC1 clock

In commit 3f905469c8ce ("clk: qcom: gcc: Use floor ops for SDCC clocks")
floor ops were applied to SDCC2 only, but flooring is also required on
the SDCC1 apps clock which is used by the eMMC card on Sony's Nile
platform, and otherwise result in the typicial "Card appears
overclocked" warnings observed on many other platforms before:

    mmc0: Card appears overclocked; req 52000000 Hz, actual 100000000 Hz
    mmc0: Card appears overclocked; req 52000000 Hz, actual 100000000 Hz
    mmc0: Card appears overclocked; req 104000000 Hz, actual 192000000 Hz

Fixes: f2a76a2955c0 ("clk: qcom: Add Global Clock controller (GCC) driver for SDM660")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Tested-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220714203822.186448-1-marijn.suijten@somainline.org

dt-bindings: clock: qcom,mmcc: define clocks/clock-names for MSM8996

Define clock/clock-names properties of the MMCC device node to be used
on MSM8996 platform.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220705112734.1323355-3-dmitry.baryshkov@linaro.org

dt-bindings: clock: qcom,mmcc: fix clocks/clock-names definitions

Rather than defining (incorrect) global clocks and clock-names lists,
define them per platform using conditionals. Also, while we are at it,
mark these properties as required for all platforms for which DT files
contained clocks/clock-names for the MMCC nodes from the beginning (in
addition to existing MSM8998 this adds MSM8994, SDM630 and SDM660).

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220705112734.1323355-2-dmitry.baryshkov@linaro.org

clk: qcom: gcc-msm8916: use parent_hws/_data instead of parent_names

Convert the clock driver to specify parent data rather than parent
names, to actually bind using 'clock-names' specified in the DTS rather
than global clock names. Use parent_hws where possible to refer parent
clocks directly, skipping the lookup.

Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220704172453.838303-7-dmitry.baryshkov@linaro.org

clk: qcom: gcc-msm8916: move gcc_mss_q6_bimc_axi_clk down

The gcc_mss_q6_bimc_axi_clk clock depends on the bimc_ddr_clk_src clock.
Move it down in the file to come after the source clock.

Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220704172453.838303-6-dmitry.baryshkov@linaro.org

clk: qcom: gcc-msm8916: move GPLL definitions up

Move GPLL definitions up, before the clock parent tables, so that we can
use gpll hw clock fields in the parent_data/parent_hws tables.

Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220704172453.838303-5-dmitry.baryshkov@linaro.org

clk: qcom: gcc-msm8916: use ARRAY_SIZE instead of specifying num_parents

Use ARRAY_SIZE() instead of manually specifying num_parents. This makes
adding/removing entries to/from parent_data easy and errorproof.

This conversion fixes an issue present since the first version of this
driver. For the gp1_clk_src, gp2_clk_src and gp3_clk_src it was
impossible to select sleep_clk as a prent of the clock, since
num_parents was limited to 3 rather than 4. Switching to use num_parents
automatically makes sleep_clk available for selection.

Fixes: 3966fab8b6ab ("clk: qcom: Add MSM8916 Global Clock Controller support")
Cc: Georgi Djakov <djakov@kernel.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220704172453.838303-4-dmitry.baryshkov@linaro.org

dt-bindings: clock: separate bindings for MSM8916 GCC device

Separate bindings for GCC on Qualcomm MSM8916 platforms. This adds new
clocks/clock-names properties to be used for clock links.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220704172453.838303-3-dmitry.baryshkov@linaro.org

dt-bindings: clk: qcom,gcc-*: use qcom,gcc.yaml

Use qcom,gcc.yaml which contains a set of properties common to most
Qualcomm GCC bindings.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220704172453.838303-2-dmitry.baryshkov@linaro.org

clk: gcc-sc8280xp: keep USB power-domains always-on

The Qualcomm DWC3 driver suspend implementation appears to be incomplete
for SC8280XP so keep the USB power domains always-on for now so that the
controller survives a suspend cycle.

Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220805121250.10347-3-johan+linaro@kernel.org

clk: gcc-sc8280xp: keep PCIe power-domains always-on

The Qualcomm PCIe driver does not yet implement suspend so to keep the
PCIe power domains always-on for now to avoid crashing during resume.

Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220805121250.10347-2-johan+linaro@kernel.org

Linux 6.0-rc1

radix-tree: replace gfp.h inclusion with gfp_types.h

Radix tree header includes gfp.h for __GFP_BITS_SHIFT only. Now we
have gfp_types.h for this.

Fixes powerpc allmodconfig build:

   In file included from include/linux/nodemask.h:97,
                    from include/linux/mmzone.h:17,
                    from include/linux/gfp.h:7,
                    from include/linux/radix-tree.h:12,
                    from include/linux/idr.h:15,
                    from include/linux/kernfs.h:12,
                    from include/linux/sysfs.h:16,
                    from include/linux/kobject.h:20,
                    from include/linux/pci.h:35,
                    from arch/powerpc/kernel/prom_init.c:24:
   include/linux/random.h: In function 'add_latent_entropy':
>> include/linux/random.h:25:46: error: 'latent_entropy' undeclared (first use in this function); did you mean 'add_latent_entropy'?
      25 |         add_device_randomness((const void *)&latent_entropy, sizeof(latent_entropy));
         |                                              ^~~~~~~~~~~~~~
         |                                              add_latent_entropy
   include/linux/random.h:25:46: note: each undeclared identifier is reported only once for each function it appears in

Reported-by: kernel test robot <lkp@intel.com>
CC: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'pull-fixes' of git://git./linux/kernel/git/viro/vfs

Pull vfs lseek fix from Al Viro:
 "Fix proc_reg_llseek() breakage. Always had been possible if somebody
  left NULL ->proc_lseek, became a practical issue now"

* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  take care to handle NULL ->proc_lseek()

take care to handle NULL ->proc_lseek()

Easily done now, just by clearing FMODE_LSEEK in ->f_mode
during proc_reg_open() for such entries.

Fixes: 868941b14441 "fs: remove no_llseek"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Merge tag 'for-linus-6.0-rc1b-tag' of git://git./linux/kernel/git/xen/tip

Pull more xen updates from Juergen Gross:

 - fix the handling of the "persistent grants" feature negotiation
   between Xen blkfront and Xen blkback drivers

 - a cleanup of xen.config and adding xen.config to Xen section in
   MAINTAINERS

 - support HVMOP_set_evtchn_upcall_vector, which is more compliant to
   "normal" interrupt handling than the global callback used up to now

 - further small cleanups

* tag 'for-linus-6.0-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  MAINTAINERS: add xen config fragments to XEN HYPERVISOR sections
  xen: remove XEN_SCRUB_PAGES in xen.config
  xen/pciback: Fix comment typo
  xen/xenbus: fix return type in xenbus_file_read()
  xen-blkfront: Apply 'feature_persistent' parameter when connect
  xen-blkback: Apply 'feature_persistent' parameter when connect
  xen-blkback: fix persistent grants negotiation
  x86/xen: Add support for HVMOP_set_evtchn_upcall_vector

Merge tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git./linux/kernel/git/acme/linux

Pull more perf tool updates from Arnaldo Carvalho de Melo:

 - 'perf c2c' now supports ARM64, adjust its output to cope with
   differences with what is in x86_64. Now go find false sharing on
   ARM64 (at least Neoverse) as well!

 - Refactor the JSON processing, making the output more compact and thus
   reducing the size of the resulting perf binary

 - Improvements for 'perf offcpu' profiling, including tracking child
   processes

 - Update Intel JSON metrics and events files for broadwellde,
   broadwellx, cascadelakex, haswellx, icelakex, ivytown, jaketown,
   knightslanding, sapphirerapids, skylakex and snowridgex

 - Add 'perf stat' JSON output and a 'perf test' entry for it

 - Ignore memfd and anonymous mmap events if jitdump present

 - Refactor 'perf test' shell tests allowing subdirs

 - Fix an error handling path in 'parse_perf_probe_command()'

 - Fixes for the guest Intel PT tracing patchkit in the 1st batch of
   this merge window

 - Print debuginfod queries if -v option is used, to explain delays in
   processing when debuginfo servers are enabled to fetch DSOs with
   richer symbol tables

 - Improve error message for 'perf record -p not_existing_pid'

 - Fix openssl and libbpf feature detection

 - Add PMU pai_crypto event description for IBM z16 on 'perf list'

 - Fix typos and duplicated words on comments in various places

* tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (81 commits)
  perf test: Refactor shell tests allowing subdirs
  perf vendor events: Update events for snowridgex
  perf vendor events: Update events and metrics for skylakex
  perf vendor events: Update metrics for sapphirerapids
  perf vendor events: Update events for knightslanding
  perf vendor events: Update metrics for jaketown
  perf vendor events: Update metrics for ivytown
  perf vendor events: Update events and metrics for icelakex
  perf vendor events: Update events and metrics for haswellx
  perf vendor events: Update events and metrics for cascadelakex
  perf vendor events: Update events and metrics for broadwellx
  perf vendor events: Update metrics for broadwellde
  perf jevents: Fold strings optimization
  perf jevents: Compress the pmu_events_table
  perf metrics: Copy entire pmu_event in find metric
  perf pmu-events: Hide the pmu_events
  perf pmu-events: Don't assume pmu_event is an array
  perf pmu-events: Move test events/metrics to JSON
  perf test: Use full metric resolution
  perf pmu-events: Hide pmu_events_map
  ...

Merge tag 'powerpc-6.0-2' of git://git./linux/kernel/git/powerpc/linux

Pull powerpc fixes from Michael Ellerman:

 - Ensure we never emit lwarx with EH=1 on 32-bit, because some 32-bit
   CPUs trap on it rather than ignoring it as they should.

 - Fix ftrace when building with clang, which was broken by some
   refactoring.

 - A couple of other minor fixes.

Thanks to Christophe Leroy, Naveen N.  Rao, Nick Desaulniers, Ondrej
Mosnacek, Pali Rohár, Russell Currey, and Segher Boessenkool.

* tag 'powerpc-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/kexec: Fix build failure from uninitialised variable
  powerpc/ppc-opcode: Fix PPC_RAW_TW()
  powerpc64/ftrace: Fix ftrace for clang builds
  powerpc: Make eh value more explicit when using lwarx
  powerpc: Don't hide eh field of lwarx behind a macro
  powerpc: Fix eh field when calling lwarx on PPC32

Merge tag 'pull-work.misc' of git://git./linux/kernel/git/viro/vfs

Pull /proc/mounts fix from Al Viro:
 "Fix for /proc/mounts escaping - escape the '#' character too"

* tag 'pull-work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  vfs: escape hash as well

Merge tag '5.20-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6

Pull more cifs updates from Steve French:

 - two fixes for stable, one for a lock length miscalculation, and
   another fixes a lease break timeout bug

 - improvement to handle leases, allows the close timeout to be
   configured more safely

 - five restructuring/cleanup patches

* tag '5.20-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: Do not access tcon->cfids->cfid directly from is_path_accessible
  cifs: Add constructor/destructors for tcon->cfid
  SMB3: fix lease break timeout when multiple deferred close handles for the same file.
  smb3: allow deferred close timeout to be configurable
  cifs: Do not use tcon->cfid directly, use the cfid we get from open_cached_dir
  cifs: Move cached-dir functions into a separate file
  cifs: Remove {cifs,nfs}_fscache_release_page()
  cifs: fix lock length calculation

afs: Enable multipage folio support

Enable multipage folio support for the afs filesystem.

Support has already been implemented in netfslib, fscache and cachefiles
and in most of afs, but I've waited for Matthew Wilcox's latest folio
changes.

Note that it does require a change to afs_write_begin() to return the
correct subpage.  This is a "temporary" change as we're working on
getting rid of the need for ->write_begin() and ->write_end()
completely, at least as far as network filesystems are concerned - but
it doesn't prevent afs from making use of the capability.

Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Tested-by: kafs-testing@auristor.com
Cc: Marc Dionne <marc.dionne@auristor.com>
Cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/lkml/2274528.1645833226@warthog.procyon.org.uk/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'timers-urgent-2022-08-13' of git://git./linux/kernel/git/tip/tip

Pull timer fixes from Ingo Molnar:
 "Misc timer fixes:

   - fix a potential use-after-free bug in posix timers

   - correct a prototype

   - address a build warning"

* tag 'timers-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  posix-cpu-timers: Cleanup CPU timers before freeing them during exec
  time: Correct the prototype of ns_to_kernel_old_timeval and ns_to_timespec64
  posix-timers: Make do_clock_gettime() static

Merge tag 'x86-urgent-2022-08-13' of git://git./linux/kernel/git/tip/tip

Pull x86 fix from Ingo Molnar:
 "Fix the 'IBPB mitigated RETBleed' mode of operation on AMD CPUs (not
  turned on by default), which also need STIBP enabled (if available) to
  be '100% safe' on even the shortest speculation windows"

* tag 'x86-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/bugs: Enable STIBP for IBPB mitigated RETBleed

Merge tag 'i2c-for-5.20-part2' of git://git./linux/kernel/git/wsa/linux

Pull more i2c updates from Wolfram Sang:

 - two driver fixes for issues introduced this cycle

 - one trivial driver improvement regarding ACPI

 - more DTS conversion and additions

 - documentation updates

 - subsystem-wide move from strlcpy to strscpy

* tag 'i2c-for-5.20-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  docs: i2c: i2c-sysfs: fix hyperlinks
  docs: i2c: i2c-sysfs: improve wording
  docs: i2c: instantiating-devices: add syntax coloring to dts and C blocks
  docs: i2c: smbus-protocol: improve DataLow/DataHigh definition
  docs: i2c: i2c-protocol: remove unused legend items
  docs: i2c: i2c-protocol,smbus-protocol: remove nonsense words
  docs: i2c: i2c-protocol: update introductory paragraph
  i2c: move core from strlcpy to strscpy
  i2c: move drivers from strlcpy to strscpy
  i2c: kempld: Support ACPI I2C device declaration
  i2c: mediatek: add i2c compatible for MT8188
  dt-bindings: i2c: update bindings for mt8188 soc
  i2c: microchip-corei2c: fix erroneous late ack send
  dt-bindings: i2c: qcom,i2c-cci: convert to dtschema
  i2c: qcom-geni: Fix GPI DMA buffer sync-back

Merge tag 'ntb-5.20' of https://github.com/jonmason/ntb

Pull NTB updates from Jon Mason:
 "Non-Transparent Bridge updates.

  Fix of heap data and clang warnings, support for a new Intel NTB
  device, and NTB EndPoint Function (EPF) support and the various fixes
  for that"

* tag 'ntb-5.20' of https://github.com/jonmason/ntb:
  MAINTAINERS: add PCI Endpoint NTB drivers to NTB files
  NTB: EPF: Tidy up some bounds checks
  NTB: EPF: Fix error code in epf_ntb_bind()
  PCI: endpoint: pci-epf-vntb: reduce several globals to statics
  PCI: endpoint: pci-epf-vntb: fix error handle in epf_ntb_mw_bar_init()
  PCI: endpoint: Fix Kconfig dependency
  NTB: EPF: set pointer addr to null using NULL rather than 0
  Documentation: PCI: extend subheading underline for "lspci output" section
  Documentation: PCI: Use code-block block for scratchpad registers diagram
  Documentation: PCI: Add specification for the PCI vNTB function device
  PCI: endpoint: Support NTB transfer between RC and EP
  NTB: epf: Allow more flexibility in the memory BAR map method
  PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address
  ntb: intel: add GNR support for Intel PCIe gen5 NTB
  NTB: ntb_tool: uninitialized heap data in tool_fn_write()
  ntb: idt: fix clang -Wformat warnings