media: saa7146: add cleanup in hexium_attach()

If saa7146_register_device() fails, no cleanup is executed, leading to
memory/resource leaks. To fix this issue, perform necessary cleanup work
before returning the error.

Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: usb: cx231xx-417: fix a memory leak bug

In cx231xx_load_firmware(), 'p_buffer' is allocated through vmalloc() to
hold the firmware. However, after the usage, it is not deallocated, leading
to a memory leak bug.

Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: cpia2_usb: fix memory leaks

In submit_urbs(), 'cam->sbuf[i].data' is allocated through kmalloc_array().
However, it is not deallocated if the following allocation for urbs fails.
To fix this issue, free 'cam->sbuf[i].data' if usb_alloc_urb() fails.

Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: imx: add csc/scaler mem2mem device

Add a single imx-media mem2mem video device that uses the IPU IC PP
(image converter post processing) task for scaling and colorspace
conversion.
On i.MX6Q/DL SoCs with two IPUs currently only the first IPU is used.

The hardware only supports writing to destination buffers up to
1024x1024 pixels in a single pass, arbitrary sizes can be achieved
by rendering multiple tiles per frame.

[slongerbeam@gmail.com: use ipu_image_convert_adjust(), fix
 device_run() error handling, add missing media-device header,
 unregister and remove the mem2mem device in error paths in
 imx_media_probe_complete() and in imx_media_remove(), updated
 for sync subdev registration]

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: correct two minor checkpatch issues]
[hverkuil-cisco@xs4all.nl: sparse warning: make imx6_media_probe_complete static]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: cec-notifier: clear cec_adap in cec_notifier_unregister

If cec_notifier_cec_adap_unregister() is called before
cec_unregister_adapter() then everything is OK (and this is the
case today). But if it is the other way around, then
cec_notifier_unregister() is called first, and that doesn't
set n->cec_adap to NULL.

So if e.g. cec_notifier_set_phys_addr() is called after
cec_notifier_unregister() but before cec_unregister_adapter()
then n->cec_adap points to an unregistered and likely deleted
cec adapter. So just set n->cec_adap->notifier and n->cec_adap
to NULL for rubustness.

Eventually cec_notifier_unregister will disappear and this will
be simplified substantially.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: cec-adap: return from cec_s_conn_info() if adap is invalid

Check if cec_s_conn_info is called with a valid cec adapter,
do nothing if it is invalid.

This makes it possible to call this function even if CEC support is
disabled in the kernel config.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: sunxi: Add A10 CSI driver

The older CSI drivers have camera capture interface different from the one
in the newer ones.

This IP is pretty simple. Some variants (one controller out of two
instances on some SoCs) have an ISP embedded, but there's no code that make
use of it, so we ignored that part for now.

[Sakari Ailus: Wrapped a few long lines, set mbus code using a macro.]

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: sunxi: Refactor the Makefile and Kconfig

The Makefile and Kconfig for the sun6i CSI driver are included in the main
Makefile / KConfig file. Since we're going to add a new CSI driver for an
older chip, and the Cedrus driver eventually, it makes more sense to put
those in our directory.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dt-bindings: media: Add Allwinner A10 CSI binding

The Allwinner A10 CMOS Sensor Interface is a camera capture interface also
used in later (A10s, A13, A20, R8 and GR8) SoCs.

On some SoCs, like the A10, there's multiple instances of that controller,
with one instance supporting more channels and having an ISP.

[Sakari Ailus: Add type: object to the endpoint node.]

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: atmel: atmel-isi: fix timeout value for stop streaming

In case of sensor malfunction, stop streaming timeout takes much longer
than expected. This is due to conversion of time to jiffies: milliseconds
multiplied with HZ (ticks/second) gives out a value of jiffies with 10^3
greater. We need to also divide by 10^3 to obtain the right jiffies value.
In other words FRAME_INTERVAL_MILLI_SEC must be in seconds in order to
multiply by HZ and get the right jiffies value to add to the current
jiffies for the timeout expire time.

Fixes: 195ebc43bf76 ("[media] V4L: at91: add Atmel Image Sensor Interface (ISI) support")
Signed-off-by: Alexandre Kroupski <alexandre.kroupski@ingenico.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dt-bindings: media: Convert Allwinner A10 IR to a schema

The older Allwinner SoCs have a IR receiver supported in Linux, with a
matching Device Tree binding.

Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dt-bindings: media: Add YAML schemas for the generic RC bindings

The RC controllers have a bunch of generic properties that are needed in a
device tree. Add a YAML schemas for those.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ttusb-dec: Fix info-leak in ttusb_dec_send_command()

The function at issue does not always initialize each byte allocated
for 'b' and can therefore leak uninitialized memory to a USB device in
the call to usb_bulk_msg()

Use kzalloc() instead of kmalloc()

Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+0522702e9d67142379f1@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dvb-frontends/cxd2099: Make en_templ constant

Static structure en_templ, of type dvb_ca_en50221, is not used except to
be copied into a local variable. Hence make it const to prevent
unintended modification of the original fields.
Issue found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ec168: Make structure ec168_props constant

The static structure ec168_props, of type dvb_usb_device_properties, is
used only once, when it is assigned to field props of the constant
structure ec168_driver_info. As this means that ec168_props will never be
modified, make it const as well in order to prevent unintended
modification of its fields.
Issue found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: firewire: Make structure fdtv_ca constant

Static structure fdtv_ca, of type dvb_device, is only used when it is
passed as the third argument to function dvb_register_device(). However,
in the definition of dvb_register_device, the third parameter is
declared as constant. Hence make fdtv_ca const as well.
Issue found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dvb-bt8xx: Make variable dst_config constant

Static structure dst_config, of type dst_config, is not used except to
be assigned as the value of field state of a variable having type
dst_state *. In the definition of dst_state, field config is declared as
const. Hence dst_config, when assigned to config, cannot be modified.
Therefore, make dst_config const as well.
Issue found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dvb-usb: add T230 to dvbsky

commit 5fa88151ecdb ("[media] dvb-usb-cxusb: Geniatech T230 - resync TS
FIFO after lock") does not solve the problem for all devices. This is the
same issue reported on the T230C, which was moved to the dvbsky.c driver
to work around this issue in commit 5742240577b6 ("media: dvbsky: MyGica
T230C support").

In addition, the cxusb driver causes an oops when unplugging the device
while streaming; this problem does not happen any more.

Signed-off-by: Jan Pieter van Woerkom <jp@jpvw.nl>
Tested-by: James Hutchinson <jahutchinson99@googlemail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dvb-usb: remove T230 from cxusb

Remove this device from the cxusb driver so it can be added to the dvbsky
driver.

Signed-off-by: Jan Pieter van Woerkom <jp@jpvw.nl>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dvb-core: fix a memory leak bug

In dvb_create_media_entity(), 'dvbdev->entity' is allocated through
kzalloc(). Then, 'dvbdev->pads' is allocated through kcalloc(). However, if
kcalloc() fails, the allocated 'dvbdev->entity' is not deallocated, leading
to a memory leak bug. To fix this issue, free 'dvbdev->entity' before
returning -ENOMEM.

Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ttpci: unknown protocol is rc-mm-32

This protocol responds to a real philips rc-mm remote; it does not respond
to IR encoded with the encoder in ir-rcmm-decoder.c.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dvb-frontends: fix a memory leak bug

In cx24117_load_firmware(), 'buf' is allocated through kmalloc() to hold
the firmware. However, if i2c_transfer() fails, it is not deallocated,
leading to a memory leak bug.

Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dvb-frontends: fix memory leaks

In dib7000pc_detection(), 'tx' and 'rx' are allocated through kzalloc()
respectively. However, if DiB7000PC is detected, they are not deallocated,
leading to memory leaks. To fix this issue, create a label to free 'tx' and
'rx' before returning from the function.

Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: mceusb: fix (eliminate) TX IR signal length limit

Fix and eliminate mceusb's IR length limit for IR signals transmitted to
the MCE IR blaster ports.

An IR signal TX exceeding 306 pulse/space samples presently causes -EINVAL
return error. There's no such limitation nor error with the MCE device
hardware. And valid IR signals exist with more than 400 pulse/space for the
control of certain appliances (eg Panasonic ACXA75C00600 air conditioner).

The scope of this patch is limited to the mceusb driver. There are still
IR signal TX length and time constraints that related modules of rc core
(eg LIRC) impose, further up the driver stack.

Changes for mceusb_tx_ir():

Converts and sends LIRC IR pulse/space sequence to MCE device IR
pulse/space format.

Break long length LIRC sequence into multiple (unlimited number of) parts
for sending to the MCE device.
Reduce kernel stack IR buffer size: 128 (was 384)
Increase MCE IR data packet size: 31 (was 5)
Zero time LIRC pulse/space no longer copied to MCE IR data.
Eliminate overwriting the source/input LIRC IR data in txbuf[].
Eliminate -EINVAL return; return number of IR samples sent (>0) or
MCE write error code (<0).

New mce_write() and mce_write_callback():

Implements synchronous blocking I/O, with timeout, for writing/sending
data to the MCE device.

An unlimited multipart IR signal sent to the MCE device faster than real
time requires flow control absent with the original mce_request_packet()
and mce_async_callback() asynchronous I/O implementation. Also absent is
TX error feedback.

mce_write() combines and replaces mce_request_packet() and
mce_async_callback() with conversion to synchronous I/O.
mce_write() returns bytes sent (>0) or MCE device write error (<0).
Debug hex dump TX data before processing.

Rename mce_async_out() -> mce_command_out():

The original name is misleading with underlying synchronous I/O
implementation. Function renamed to mce_command_out().

Changes in mceusb_handle_command():

Add support for MCE device error case MCE_RSP_TX_TIMEOUT
"IR TX timeout (TX buffer underrun)"

Changes in mceusb_dev_printdata():

Changes support test and debug of multipart TX IR.

Add buffer boundary information (offset and buffer size) to TX hex dump.
Correct TX trace bug "Raw IR data, 0 pulse/space samples"
Add trace for MCE_RSP_TX_TIMEOUT "IR TX timeout (TX buffer underrun)"

Other changes:

The driver's write to USB device architecture change (async to sync I/O)
is significant so we bump DRIVER_VERSION to "1.95" (from "1.94").

Tests:

$ cat -n irdata1 | head -3
     1  carrier 36000
     2  pulse 6350
     3  space 6350
$ cat -n irdata1 | tail -3
    76  pulse 6350
    77  space 6350
    78  pulse 6350
$ ir-ctl -s irdata1

[1549021.073612] mceusb 1-1.3:1.0: requesting 36000 HZ carrier
[1549021.073635] mceusb 1-1.3:1.0: tx data[0]: 9f 06 01 45 (len=4 sz=4)
[1549021.073649] mceusb 1-1.3:1.0: Request carrier of 35714 Hz (period 28us)
[1549021.073848] mceusb 1-1.3:1.0: tx done status = 4 (wait = 100, expire = 100 (1000ms), urb->actual_length = 4, urb->status = 0)
[1549021.074689] mceusb 1-1.3:1.0: rx data[0]: 9f 06 01 45 (len=4 sz=4)
[1549021.074701] mceusb 1-1.3:1.0: Got carrier of 35714 Hz (period 28us)
[1549021.102023] mceusb 1-1.3:1.0: tx data[0]: 9f 08 03 (len=3 sz=3)
[1549021.102036] mceusb 1-1.3:1.0: Request transmit blaster mask of 0x03
[1549021.102219] mceusb 1-1.3:1.0: tx done status = 3 (wait = 100, expire = 100 (1000ms), urb->actual_length = 3, urb->status = 0)
[1549021.131979] mceusb 1-1.3:1.0: tx data[0]: 9e ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f 9e ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f 91 ff (len=81 sz=81)
[1549021.131992] mceusb 1-1.3:1.0: Raw IR data, 30 pulse/space samples
[1549021.133592] mceusb 1-1.3:1.0: tx done status = 81 (wait = 100, expire = 100 (1000ms), urb->actual_length = 81, urb->status = 0)

Hex dumps limited to 64 bytes.
0xff is MCE maximum time pulse, 0x7f is MCE maximum time space.

$ cat -n irdata2 | head -3
     1  carrier 36000
     2  pulse 50
     3  space 50
$ cat -n irdata2 | tail -3
   254  pulse 50
   255  space 50
   256  pulse 50
$ ir-ctl -s irdata2

[1549306.586998] mceusb 1-1.3:1.0: tx data[0]: 9f 08 03 (len=3 sz=3)
[1549306.587015] mceusb 1-1.3:1.0: Request transmit blaster mask of 0x03
[1549306.587252] mceusb 1-1.3:1.0: tx done status = 3 (wait = 100, expire = 100 (1000ms), urb->actual_length = 3, urb->status = 0)
[1549306.613275] mceusb 1-1.3:1.0: tx data[0]: 9e 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 9e 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 9e 81 (len=128 sz=128)
[1549306.613291] mceusb 1-1.3:1.0: Raw IR data, 30 pulse/space samples
[1549306.614837] mceusb 1-1.3:1.0: tx done status = 128 (wait = 100, expire = 100 (1000ms), urb->actual_length = 128, urb->status = 0)
[1549306.614861] mceusb 1-1.3:1.0: tx data[0]: 9e 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 9e 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 9e 01 (len=128 sz=128)
[1549306.614869] mceusb 1-1.3:1.0: Raw IR data, 30 pulse/space samples
[1549306.620199] mceusb 1-1.3:1.0: tx done status = 128 (wait = 100, expire = 100 (1000ms), urb->actual_length = 128, urb->status = 0)
[1549306.620212] mceusb 1-1.3:1.0: tx data[0]: 89 81 01 81 01 81 01 81 01 81 80 (len=11 sz=11)
[1549306.620221] mceusb 1-1.3:1.0: Raw IR data, 9 pulse/space samples
[1549306.633294] mceusb 1-1.3:1.0: tx done status = 11 (wait = 98, expire = 100 (1000ms), urb->actual_length = 11, urb->status = 0)

Hex dumps limited to 64 bytes.
0x81 is MCE minimum time pulse, 0x01 is MCE minimum time space.
TX IR part 3 sz=11 shows 20msec I/O blocking delay
(100expire - 98wait = 2jiffies)

Signed-off-by: A Sun <as1033x@comcast.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: add keymap for HardKernel ODROID remote

This is a simple NEC remote control device shipped with the HardKernel
ODROID range of SBC devices.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: add keymap for WeTeK Play 2 remote

The WeTek Play 2 Android STB ships with an unusual remote where the
main up/down/left/right/enter controls are surrounded with an outer
ring of additional keys which are listed in clockwise order.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: add keymap for WeTek Hub remote

The WeTek Hub Android STB ships with a simple NEC remote.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: add keymap for Tanix TX5 max remote

The Tanix TX5 max Android STB ships with a simple NEC remote.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: add keymap for Tanix TX3 mini remote

The Tanix TX3 mini Android STB ships with a simple NEC remote.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: add keymap for Khadas VIM/EDGE remote

Khadas VIM and Edge SBC devices use the same NEC remote device. The
remote includes a mouse button for Android use. This has been mapped
to KEY_MUTE.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: add keymap for Amediatech X96-MAX remote

The X96-Max Android STB ships with a simple NEC remote. It includes
a TV section with preset buttons for controlling a TV. These are not
configurable, but are noted to aid visual recognition of the device.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: si2168: Refactor command setup code

Use cmd_init() to fill a struct si2168_cmd command.

Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dvb-frontends: use ida for pll number

KASAN: global-out-of-bounds Read in dvb_pll_attach

Syzbot reported global-out-of-bounds Read in dvb_pll_attach, while
accessing id[dvb_pll_devcount], because dvb_pll_devcount was 65,
that is more than size of 'id' which is DVB_PLL_MAX(64).

Rather than increasing dvb_pll_devcount every time, use ida so that
numbers are allocated correctly. This does mean that no more than
64 devices can be attached at the same time, but this is more than
sufficient.

usb 1-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the
software demuxer
dvbdev: DVB: registering new adapter (774 Friio White ISDB-T USB2.0)
usb 1-1: media controller created
dvbdev: dvb_create_media_entity: media entity 'dvb-demux' registered.
tc90522 0-0018: Toshiba TC90522 attached.
usb 1-1: DVB: registering adapter 0 frontend 0 (Toshiba TC90522 ISDB-T
module)...
dvbdev: dvb_create_media_entity: media entity 'Toshiba TC90522 ISDB-T
module' registered.
==================================================================
BUG: KASAN: global-out-of-bounds in dvb_pll_attach+0x6c5/0x830
drivers/media/dvb-frontends/dvb-pll.c:798
Read of size 4 at addr ffffffff89c9e5e0 by task kworker/0:1/12

CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.2.0-rc6+ #13
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
  __dump_stack lib/dump_stack.c:77 [inline]
  dump_stack+0xca/0x13e lib/dump_stack.c:113
  print_address_description+0x67/0x231 mm/kasan/report.c:188
  __kasan_report.cold+0x1a/0x32 mm/kasan/report.c:317
  kasan_report+0xe/0x20 mm/kasan/common.c:614
  dvb_pll_attach+0x6c5/0x830 drivers/media/dvb-frontends/dvb-pll.c:798
  dvb_pll_probe+0xfe/0x174 drivers/media/dvb-frontends/dvb-pll.c:877
  i2c_device_probe+0x790/0xaa0 drivers/i2c/i2c-core-base.c:389
  really_probe+0x281/0x660 drivers/base/dd.c:509
  driver_probe_device+0x104/0x210 drivers/base/dd.c:670
  __device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
  bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
  __device_attach+0x217/0x360 drivers/base/dd.c:843
  bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514
  device_add+0xae6/0x16f0 drivers/base/core.c:2111
  i2c_new_client_device+0x5b3/0xc40 drivers/i2c/i2c-core-base.c:778
  i2c_new_device+0x19/0x50 drivers/i2c/i2c-core-base.c:821
  dvb_module_probe+0xf9/0x220 drivers/media/dvb-core/dvbdev.c:985
  friio_tuner_attach+0x125/0x1d0 drivers/media/usb/dvb-usb-v2/gl861.c:536
  dvb_usbv2_adapter_frontend_init
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:675 [inline]
  dvb_usbv2_adapter_init drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:804
[inline]
  dvb_usbv2_init drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:865 [inline]
  dvb_usbv2_probe.cold+0x24dc/0x255d
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:980
  usb_probe_interface+0x305/0x7a0 drivers/usb/core/driver.c:361
  really_probe+0x281/0x660 drivers/base/dd.c:509
  driver_probe_device+0x104/0x210 drivers/base/dd.c:670
  __device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
  bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
  __device_attach+0x217/0x360 drivers/base/dd.c:843
  bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514
  device_add+0xae6/0x16f0 drivers/base/core.c:2111
  usb_set_configuration+0xdf6/0x1670 drivers/usb/core/message.c:2023
  generic_probe+0x9d/0xd5 drivers/usb/core/generic.c:210
  usb_probe_device+0x99/0x100 drivers/usb/core/driver.c:266
  really_probe+0x281/0x660 drivers/base/dd.c:509
  driver_probe_device+0x104/0x210 drivers/base/dd.c:670
  __device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
  bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
  __device_attach+0x217/0x360 drivers/base/dd.c:843
  bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514
  device_add+0xae6/0x16f0 drivers/base/core.c:2111
  usb_new_device.cold+0x8c1/0x1016 drivers/usb/core/hub.c:2534
  hub_port_connect drivers/usb/core/hub.c:5089 [inline]
  hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
  port_event drivers/usb/core/hub.c:5350 [inline]
  hub_event+0x1ada/0x3590 drivers/usb/core/hub.c:5432
  process_one_work+0x905/0x1570 kernel/workqueue.c:2269
  process_scheduled_works kernel/workqueue.c:2331 [inline]
  worker_thread+0x7ab/0xe20 kernel/workqueue.c:2417
  kthread+0x30b/0x410 kernel/kthread.c:255
  ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352

The buggy address belongs to the variable:
  id+0x100/0x120

Memory state around the buggy address:
  ffffffff89c9e480: fa fa fa fa 00 00 fa fa fa fa fa fa 00 00 00 00
  ffffffff89c9e500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> ffffffff89c9e580: 00 00 00 00 00 00 00 00 00 00 00 00 fa fa fa fa
                                                        ^
  ffffffff89c9e600: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
  ffffffff89c9e680: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
==================================================================

Reported-by: syzbot+8a8f48672560c8ca59dd@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: pixfmt-compressed.rst: improve H264/HEVC/MPEG1+2/VP8+9 documentation

The existing documentation was incorrect and did not correspond
to how actual codec drivers implemented this.

Update the documentation to explicitly specify what is actually
expected.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: docs-rst: Document memory-to-memory video decoder interface

Due to complexity of the video decoding process, the V4L2 drivers of
stateful decoder hardware require specific sequences of V4L2 API calls
to be followed. These include capability enumeration, initialization,
decoding, seek, pause, dynamic resolution change, drain and end of
stream.

Specifics of the above have been discussed during Media Workshops at
LinuxCon Europe 2012 in Barcelona and then later Embedded Linux
Conference Europe 2014 in Düsseldorf. The de facto Codec API that
originated at those events was later implemented by the drivers we already
have merged in mainline, such as s5p-mfc or coda.

The only thing missing was the real specification included as a part of
Linux Media documentation. Fix it now and document the decoder part of
the Codec API.

Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: vicodec: set flags for vdec/stateful OUTPUT coded formats

Tag all the coded formats where the vicodec stateful decoder supports
dynamic resolution switching and bytestream parsing.

Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: mtk-vcodec: flag OUTPUT formats with V4L2_FMT_FLAG_DYN_RESOLUTION

Tag all the coded formats where the mtk-vcodec decoder supports dynamic
resolution switching.

Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: venus: vdec: flag OUTPUT formats with V4L2_FMT_FLAG_DYN_RESOLUTION

Tag all the coded formats where the venus vdec supports dynamic
resolution switching.

Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: videodev2.h: add V4L2_FMT_FLAG_DYN_RESOLUTION

Add an enum_fmt format flag to specifically tag coded formats where
dynamic resolution switching is supported by the device.

This is useful for some codec drivers that can support dynamic
resolution switching for one or more of their listed coded formats. It
allows userspace to know whether it should extract the video parameters
itself, or if it can rely on the device to send V4L2_EVENT_SOURCE_CHANGE
when such changes are detected.

Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: videodev2.h: add V4L2_FMT_FLAG_CONTINUOUS_BYTESTREAM

Add an enum_fmt format flag to specifically tag coded formats where
full bytestream parsing is supported by the device.

Some stateful decoders are capable of fully parsing a bytestream,
but others require that userspace pre-parses the bytestream into
frames or fields (see the corresponding pixelformat descriptions
for details).

If this flag is set, then this pre-parsing step is not required
(but still possible, of course).

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: hantro: Enable H264 decoding on rk3288

Now that the generic bits have been added, we can activate H264 decoding
on rk3288.

Signed-off-by: Hertz Wong <hertz.wong@rock-chips.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: hantro: Add support for H264 decoding on G1

Add the G1 specific bits to support H264 decoding.

Signed-off-by: Hertz Wong <hertz.wong@rock-chips.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: hantro: Add core bits to support H264 decoding

Add helpers and patch hantro_{drv,v4l2}.c to prepare addition of H264
decoding support.

Signed-off-by: Hertz Wong <hertz.wong@rock-chips.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: hantro: Move copy_metadata() before doing a decode operation

Some decoders use intra slice/frame references. The capture buffer
pointed by these references might be new and thus have invalid
timestamp which prevents the decoder logic from retrieving the
vb2_buffer object based on the output buf timestamp.
Copy all metadata (including the timestamp) before starting the decode
operation.

Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: cedrus: Specify H264 startcode and decoding mode

The cedrus VPU is slice-based and expects V4L2_PIX_FMT_H264_SLICE
buffers to contain H264 slices with no start code.

Expose this to userspace with the newly added menu control.

These two controls are specified as mandatory for applications,
but we mark them as non-required on the driver side for
backwards compatibility.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: cedrus: Cleanup control initialization

In order to introduce other controls, the control initialization
needs to support an initial struct v4l2_ctrl_control.

While here, let's cleanup the control initialization,
removing unneeded fields.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: uapi: h264: Get rid of the p0/b0/b1 ref-lists

Those lists can be extracted from the dpb, let's simplify userspace
life and build that list kernel-side (generic helpers will be provided
for drivers that need this list).

Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: uapi: h264: Add the concept of start code

Stateless decoders have different expectations about the
start code that is prepended on H264 slices. Add a
menu control to express the supported start code types
(including no start code).

Drivers are allowed to support only one start code type,
but they can support both too.

Note that this is independent of the H264 decoding mode,
which specifies the granularity of the decoding operations.
Either in frame-based or slice-based mode, this new control
will allow to define the start code expected on H264 slices.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: uapi: h264: Add the concept of decoding mode

Some stateless decoders don't support per-slice decoding granularity
(or at least not in a way that would make them efficient or easy to use).

Expose a menu to control the supported decoding modes. Drivers are
allowed to support only one decoding but they can support both too.

To fully specify the decoding operation, we need to introduce
a start_byte_offset, to indicate where slices start.

Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: uapi: h264: Rename pixel format

The V4L2_PIX_FMT_H264_SLICE_RAW name was originally suggested
because the pixel format would represent H264 slices without any
start code.

However, as we will now introduce a start code menu control,
give the pixel format a more meaningful name, while it's
still early enough to do so.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: lib/sort.c: implement sort() variant taking context argument

Our list_sort() utility has always supported a context argument that
is passed through to the comparison routine. Now there's a use case
for the similar thing for sort().

This implements sort_r by simply extending the existing sort function
in the obvious way. To avoid code duplication, we want to implement
sort() in terms of sort_r(). The naive way to do that is

static int cmp_wrapper(const void *a, const void *b, const void *ctx)
{
  int (*real_cmp)(const void*, const void*) = ctx;
  return real_cmp(a, b);
}

sort(..., cmp) { sort_r(..., cmp_wrapper, cmp) }

but this would do two indirect calls for each comparison. Instead, do
as is done for the default swap functions - that only adds a cost of a
single easily predicted branch to each comparison call.

Aside from introducing support for the context argument, this also
serves as preparation for patches that will eliminate the indirect
comparison calls in common cases.

Requested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: gspca: zero usb_buf on error

If reg_r() fails, then gspca_dev->usb_buf was left uninitialized,
and some drivers used the contents of that buffer in logic.

This caused several syzbot errors:

https://syzkaller.appspot.com/bug?extid=397fd082ce5143e2f67d
https://syzkaller.appspot.com/bug?extid=1a35278dd0ebfb3a038a
https://syzkaller.appspot.com/bug?extid=06ddf1788cfd048c5e82

I analyzed the gspca drivers and zeroed the buffer where needed.

Reported-and-tested-by: syzbot+1a35278dd0ebfb3a038a@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+397fd082ce5143e2f67d@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+06ddf1788cfd048c5e82@syzkaller.appspotmail.com
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rockchip/rga: Update maintainership

Update Jacob's address and add myself as co-maintainer.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: hdpvr: add terminating 0 at end of string

dev->usbc_buf was passed as argument for %s, but it was not safeguarded
by a terminating 0.

This caused this syzbot issue:

https://syzkaller.appspot.com/bug?extid=79d18aac4bf1770dd050

Reported-and-tested-by: syzbot+79d18aac4bf1770dd050@syzkaller.appspotmail.com
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: radio/si470x: kill urb on error

In the probe() function radio->int_in_urb was not killed if an
error occurred in the probe sequence. It was also missing in
the disconnect.

This caused this syzbot issue:

https://syzkaller.appspot.com/bug?extid=2d4fc2a0c45ad8da7e99

Reported-and-tested-by: syzbot+2d4fc2a0c45ad8da7e99@syzkaller.appspotmail.com
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: vidioc-queryctrl.rst: fix broken c:type references

One typo in the function name, one missing : after :c:type.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: stm32-dcmi: add support of several sub-devices

Add support of several sub-devices within pipeline instead
of a single one.
This allows to support a CSI-2 camera sensor connected
through a CSI-2 to parallel bridge.

Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: stm32-dcmi: add media controller support

Add media controller support to dcmi in order
to walk within remote subdevices pipeline.

Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: stm32-dcmi: trace the supported fourcc/mbus_code

Add a trace of the set of supported fourcc/mbus_code which
intersect between DCMI and source sub-device.

Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: stm32-dcmi: improve sensor subdev naming

Rename "subdev" entity struct field to "source"
to prepare for several subdev support.
Move asd field on top of entity struct.

Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: Fix various misspellings of disconnected

Fix typos.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: Clarify how menus are hidden by SUBDRV_AUTOSELECT

Some users have been having a hard time finding the hidden
menus. A typically case are camera sensor drivers
(e.g IMX219, OV5645, etc), which are common on embedded
platforms and not really "ancillary" devices.

The problem with MEDIA_SUBDRV_AUTOSELECT seems to be related
to the fact that it uses the "visible" syntax to hide
the menus.

This is not obvious and it normally takes some time to
figure out.

To fix the problem, add a comment on each of hidden menus,
which should clarify what option is causing menus to be hidden.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: MAINTAINERS: Add entry for the ov5670 driver

The ov5670 driver didn't get a MAINTAINERS entry when it was merged. Add
one now.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: imx7-media-csi: add i.MX6UL support

i.MX7 and i.MX6UL/L have the same CSI controller. So add i.MX6UL/L support
to imx7-media-csi driver.

Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dt-bindings: imx7-csi: add i.MX6UL/L support

Document "fsl,imx6ul-csi" entry.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: imx: mipi csi-2: Don't fail if initial state times-out

Not all sensors will be able to guarantee a proper initial state.
This may be either because the driver is not properly written,
or (probably unlikely) because the hardware won't support it.

While the right solution in the former case is to fix the sensor
driver, the real world not always allows right solutions, due to lack
of available documentation and support on these sensors.

Let's relax this requirement, and allow the driver to support stream start,
even if the sensor initial sequence wasn't the expected.

Also improve the warning message to better explain the problem and provide
a hint that the sensor driver needs to be fixed.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Steve Longerbeam <slongerbeam@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: docs-rst: Clarify duration of LP-11 mode

Add a sentence that makes it more clear when the CSI-2 transmitter
must, if possible, exit LP-11 mode. That is, maintain LP-11 mode
until stream on, at which point the transmitter activates the clock
lane and transition to HS mode.

Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l: Documentation: Raw Bayer formats are not RGB formats

The raw Bayer formats have been listed under the label of RGB formats but
in fact they're quite different. The latter are readily usable as such
whereas the former require quite bit of image processing before useful.

Split them into RGB and raw Bayer formats.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l: Documentation: Serial busses use parallel mbus codes

When the support for serial busses was introduced in V4L2, it was decided
to use the existing parallel bus media bus pixel codes to describe them.
While this was a practical choice at the time, it necessitates choosing
which one of the many parallel mbus pixel codes to use, for on the serial
busses these formats are effectively all equivalent.

The practice has always been to use the pixel code that describes a bus
that transfers a single sample per clock. Document this.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: i2c: ov5645: Fix power sequence

This is mostly a port of Jacopo's fix:

  commit aa4bb8b8838ffcc776a79f49a4d7476b82405349
  Author: Jacopo Mondi <jacopo@jmondi.org>
  Date:   Fri Jul 6 05:51:52 2018 -0400

  media: ov5640: Re-work MIPI startup sequence

In the OV5645 case, the changes are:

- At set_power(1) time power up MIPI Tx/Rx and set data and clock lanes in
  LP11 during 'sleep' and 'idle' with MIPI clock in non-continuous mode.
- At set_power(0) time power down MIPI Tx/Rx (in addition to the current
  power down of regulators and clock gating).
- At s_stream time enable/disable the MIPI interface output.

With this commit the sensor is able to enter LP-11 mode during power up,
as expected by some CSI-2 controllers.

Many thanks to Fabio Estevam for his help debugging this issue.

Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: omap3isp: Don't set streaming state on random subdevs

The streaming state should be set to the first upstream sub-device only,
not everywhere, for a sub-device driver itself knows how to best control
the streaming state of its own upstream sub-devices.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: omap3isp: Set device on omap3isp subdevs

The omap3isp driver registered subdevs without the dev field being set. Do
that now.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ov5640: Add support for flash and lens devices

Parse async sub-devices related to the sensor by switching the async
sub-device registration function.

Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ov8856: Check reading clock frequency succeeded

Instead of blindly trusting getting the clock frequency succeeded end then
testing it against a pre-defined value, verify reading the value
succeeded.

Fixes: 879347f0c258 ("media: ov8856: Add support for OV8856 sensor")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ov5675: Add support for OV5675 sensor

Add a V4L2 sub-device driver for Omnivision ov5675 image sensor.
This is a camera sensor using the I2C bus for control and the
CSI-2 bus for data.

This driver supports following features:
- manual exposure and analog/digital gain control support
- vblank/hblank control support
- test pattern support
- media controller support
- runtime PM support
- support following resolutions:
  + 2592x1944 at 30FPS
  + 1296x972  at 30FPS

[Sakari Ailus: Wrapped a few long lines.]
[mchehab+samsung@kernel.org: fix a checkpatch warning]

Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: vsp1: fix memory leak of dl on error return path

Currently when the call vsp1_dl_body_get fails and returns null the
error return path leaks the allocation of dl. Fix this by kfree'ing
dl before returning.

Addresses-Coverity: ("Resource leak")

Fixes: 5d7936b8e27d ("media: vsp1: Convert display lists to use new body pool")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: imon: Allow iMON RC protocol for ffdc 7e device

Allow selecting the IR protocol, MCE or iMON, for a device that
identifies as follows (with config id 0x7e):

15c2:ffdc SoundGraph Inc. iMON PAD Remote Controller

As the driver is structured to default to iMON when both RC
protocols are supported, existing users of this device (using MCE
protocol) will need to manually switch to MCE (RC-6) protocol from
userspace (with ir-keytable, sysfs).

Signed-off-by: Darius Rad <alpha@area49.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: tm6000: double free if usb disconnect while streaming

The usb_bulk_urb will kfree'd on disconnect, so ensure the pointer is set
to NULL after each free.

stop stream
urb killing
urb buffer free
tm6000: got start feed request tm6000_start_feed
tm6000: got start stream request tm6000_start_stream
tm6000: pipe reset
tm6000: got start feed request tm6000_start_feed
tm6000: got start feed request tm6000_start_feed
tm6000: got start feed request tm6000_start_feed
tm6000: got start feed request tm6000_start_feed
tm6000: IR URB failure: status: -71, length 0
xhci_hcd 0000:00:14.0: ERROR unknown event type 37
xhci_hcd 0000:00:14.0: ERROR unknown event type 37
tm6000:  error tm6000_urb_received
usb 1-2: USB disconnect, device number 5
tm6000: disconnecting tm6000 #0
==================================================================
BUG: KASAN: use-after-free in dvb_fini+0x75/0x140 [tm6000_dvb]
Read of size 8 at addr ffff888241044060 by task kworker/2:0/22

CPU: 2 PID: 22 Comm: kworker/2:0 Tainted: G        W         5.3.0-rc4+ #1
Hardware name: LENOVO 20KHCTO1WW/20KHCTO1WW, BIOS N23ET65W (1.40 ) 07/02/2019
Workqueue: usb_hub_wq hub_event
Call Trace:
 dump_stack+0x9a/0xf0
 print_address_description.cold+0xae/0x34f
 __kasan_report.cold+0x75/0x93
 ? tm6000_fillbuf+0x390/0x3c0 [tm6000_alsa]
 ? dvb_fini+0x75/0x140 [tm6000_dvb]
 kasan_report+0xe/0x12
 dvb_fini+0x75/0x140 [tm6000_dvb]
 tm6000_close_extension+0x51/0x80 [tm6000]
 tm6000_usb_disconnect.cold+0xd4/0x105 [tm6000]
 usb_unbind_interface+0xe4/0x390
 device_release_driver_internal+0x121/0x250
 bus_remove_device+0x197/0x260
 device_del+0x268/0x550
 ? __device_links_no_driver+0xd0/0xd0
 ? usb_remove_ep_devs+0x30/0x3b
 usb_disable_device+0x122/0x400
 usb_disconnect+0x153/0x430
 hub_event+0x800/0x1e40
 ? trace_hardirqs_on_thunk+0x1a/0x20
 ? hub_port_debounce+0x1f0/0x1f0
 ? retint_kernel+0x10/0x10
 ? lock_is_held_type+0xf1/0x130
 ? hub_port_debounce+0x1f0/0x1f0
 ? process_one_work+0x4ae/0xa00
 process_one_work+0x4ba/0xa00
 ? pwq_dec_nr_in_flight+0x160/0x160
 ? do_raw_spin_lock+0x10a/0x1d0
 worker_thread+0x7a/0x5c0
 ? process_one_work+0xa00/0xa00
 kthread+0x1d5/0x200
 ? kthread_create_worker_on_cpu+0xd0/0xd0
 ret_from_fork+0x3a/0x50

Allocated by task 2682:
 save_stack+0x1b/0x80
 __kasan_kmalloc.constprop.0+0xc2/0xd0
 usb_alloc_urb+0x28/0x60
 tm6000_start_feed+0x10a/0x300 [tm6000_dvb]
 dmx_ts_feed_start_filtering+0x86/0x120 [dvb_core]
 dvb_dmxdev_start_feed+0x121/0x180 [dvb_core]
 dvb_dmxdev_filter_start+0xcb/0x540 [dvb_core]
 dvb_demux_do_ioctl+0x7ed/0x890 [dvb_core]
 dvb_usercopy+0x97/0x1f0 [dvb_core]
 dvb_demux_ioctl+0x11/0x20 [dvb_core]
 do_vfs_ioctl+0x5d8/0x9d0
 ksys_ioctl+0x5e/0x90
 __x64_sys_ioctl+0x3d/0x50
 do_syscall_64+0x74/0xe0
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

Freed by task 22:
 save_stack+0x1b/0x80
 __kasan_slab_free+0x12c/0x170
 kfree+0xfd/0x3a0
 xhci_giveback_urb_in_irq+0xfe/0x230
 xhci_td_cleanup+0x276/0x340
 xhci_irq+0x1129/0x3720
 __handle_irq_event_percpu+0x6e/0x420
 handle_irq_event_percpu+0x6f/0x100
 handle_irq_event+0x55/0x84
 handle_edge_irq+0x108/0x3b0
 handle_irq+0x2e/0x40
 do_IRQ+0x83/0x1a0

Cc: stable@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: imon-rsc keymap has incorrect mappings

KEY_MAX is not a key but designates the highest value a linux keycode
can ever have.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: em28xx: modules workqueue not inited for 2nd device

syzbot reports an error on flush_request_modules() for the second device.
This workqueue was never initialised so simply remove the offending line.

usb 1-1: USB disconnect, device number 2
em28xx 1-1:1.153: Disconnecting em28xx #1
------------[ cut here ]------------
WARNING: CPU: 0 PID: 12 at kernel/workqueue.c:3031
__flush_work.cold+0x2c/0x36 kernel/workqueue.c:3031
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.3.0-rc2+ #25
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
  __dump_stack lib/dump_stack.c:77 [inline]
  dump_stack+0xca/0x13e lib/dump_stack.c:113
  panic+0x2a3/0x6da kernel/panic.c:219
  __warn.cold+0x20/0x4a kernel/panic.c:576
  report_bug+0x262/0x2a0 lib/bug.c:186
  fixup_bug arch/x86/kernel/traps.c:179 [inline]
  fixup_bug arch/x86/kernel/traps.c:174 [inline]
  do_error_trap+0x12b/0x1e0 arch/x86/kernel/traps.c:272
  do_invalid_op+0x32/0x40 arch/x86/kernel/traps.c:291
  invalid_op+0x23/0x30 arch/x86/entry/entry_64.S:1026
RIP: 0010:__flush_work.cold+0x2c/0x36 kernel/workqueue.c:3031
Code: 9a 22 00 48 c7 c7 20 e4 c5 85 e8 d9 3a 0d 00 0f 0b 45 31 e4 e9 98 86
ff ff e8 51 9a 22 00 48 c7 c7 20 e4 c5 85 e8 be 3a 0d 00 <0f> 0b 45 31 e4
e9 7d 86 ff ff e8 36 9a 22 00 48 c7 c7 20 e4 c5 85
RSP: 0018:ffff8881da20f720 EFLAGS: 00010286
RAX: 0000000000000024 RBX: dffffc0000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff8128a0fd RDI: ffffed103b441ed6
RBP: ffff8881da20f888 R08: 0000000000000024 R09: fffffbfff11acd9a
R10: fffffbfff11acd99 R11: ffffffff88d66ccf R12: 0000000000000000
R13: 0000000000000001 R14: ffff8881c6685df8 R15: ffff8881d2a85b78
  flush_request_modules drivers/media/usb/em28xx/em28xx-cards.c:3325 [inline]
  em28xx_usb_disconnect.cold+0x280/0x2a6
drivers/media/usb/em28xx/em28xx-cards.c:4023
  usb_unbind_interface+0x1bd/0x8a0 drivers/usb/core/driver.c:423
  __device_release_driver drivers/base/dd.c:1120 [inline]
  device_release_driver_internal+0x404/0x4c0 drivers/base/dd.c:1151
  bus_remove_device+0x2dc/0x4a0 drivers/base/bus.c:556
  device_del+0x420/0xb10 drivers/base/core.c:2288
  usb_disable_device+0x211/0x690 drivers/usb/core/message.c:1237
  usb_disconnect+0x284/0x8d0 drivers/usb/core/hub.c:2199
  hub_port_connect drivers/usb/core/hub.c:4949 [inline]
  hub_port_connect_change drivers/usb/core/hub.c:5213 [inline]
  port_event drivers/usb/core/hub.c:5359 [inline]
  hub_event+0x1454/0x3640 drivers/usb/core/hub.c:5441
  process_one_work+0x92b/0x1530 kernel/workqueue.c:2269
  process_scheduled_works kernel/workqueue.c:2331 [inline]
  worker_thread+0x7ab/0xe20 kernel/workqueue.c:2417
  kthread+0x318/0x420 kernel/kthread.c:255
  ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352
Kernel Offset: disabled
Rebooting in 86400 seconds..

Fixes: be7fd3c3a8c5e ("media: em28xx: Hauppauge DualHD second tuner functionality)
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Brad Love <brad@nextdimension.cc>
Reported-by: syzbot+b7f57261c521087d89bb@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: selftests: ir: fix ir_loopback test failure

The decoder is called rc-mm, not rcmm. This was renamed late in the cycle
so this bug crept in.

Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: imon_raw: prevent "nonsensical timing event of duration 0"

Sometimes the device sends IR data which is all space, no pulses
whatsoever. Add the end of this the driver will put the rc device into
idle mode when it already is in idle mode. The following will be logged:

rc rc0: nonsensical timing event of duration 0
rc rc0: two consecutive events of type space

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: imon_raw: simplify and explain bit operations

This code needs some explanation.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ir-kbd-i2c: convert to i2c_new_dummy_device()

Convert this driver to use the new i2c_new_dummy_device() call and bail
out if the dummy device cannot be registered to make failure more
visible to the user.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: add include guard to rc-map.h

Add a header include guard just in case.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: stv0900_core: remove redundant assignment to variables mclk, div and ad_div

The variables mclk, div and ad_div are being assigned with a values
that are never read and are being updated later with a new values.
The assignments are redundant and can be removed.

Addresses-Coverity: ("Unused value")

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dvb_frontend.h: Fix shifting signed 32-bit value problem

Fix DVBFE_ALGO_RECOVERY and DVBFE_ALGO_SEARCH_ERROR use BIT macro which
fixes undefined behavior error by certain compilers.

Also changed all other bit shifted definitions to use macro for better
readability.

Signed-off-by: Luke Nowakowski-Krijger <lnowakow@eng.ucsd.edu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: media/dvb: Use kmemdup rather than duplicating its implementation

kmemdup is introduced to duplicate a region of memory in a neat way.
Rather than kmalloc/kzalloc + memcpy, which the programmer needs to
write the size twice (sometimes lead to mistakes), kmemdup improves
readability, leads to smaller code and also reduce the chances of mistakes.
Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy.

Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: media/tuners: Use kmemdup rather than duplicating its implementation

kmemdup is introduced to duplicate a region of memory in a neat way.
Rather than kmalloc/kzalloc + memcpy, which the programmer needs to
write the size twice (sometimes lead to mistakes), kmemdup improves
readability, leads to smaller code and also reduce the chances of mistakes.
Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy.

Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: media/usb: Use kmemdup rather than duplicating its implementation

kmemdup is introduced to duplicate a region of memory in a neat way.
Rather than kmalloc/kzalloc + memcpy, which the programmer needs to
write the size twice (sometimes lead to mistakes), kmemdup improves
readability, leads to smaller code and also reduce the chances of mistakes.
Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy.

Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: MAINTAINERS: Remove zoran driver

Cleanup MAINTAINERS from zoran record since the driver was removed.

Fixes: 8dce4b265a53 ("media: zoran: remove deprecated driver")
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: MAINTAINERS: hantro: Fix typo in a filepath

Fix typo (s/platform//) in the directory path.

Cc: Ezequiel Garcia <ezequiel@collabora.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Fixes: a29add8c9bb2 ("media: rockchip/vpu: rename from rockchip to hantro")
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: exynos4-is: Remove call to memset after dma_alloc_coherent

In commit 518a2f1925c3
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed

Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ngene: Remove call to memset after pci_alloc_consistent

pci_alloc_consistent calls dma_alloc_coherent directly.
In commit 518a2f1925c3
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed.

Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: i2c: Convert to new i2c device probe()

The I2C core framework provides a simplified probe framework from commit
b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new() call-back type").

These drivers do not utilise the i2c_device_id table in the probe, so we
can easily convert them to utilise the simplified i2c driver
registration.

Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: i2c: et8ek8: Convert to new i2c device probe()

The I2C core framework provides a simplified probe framework from commit
b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new() call-back type").

This driver does not utilise the i2c_device_id table in the probe, so we can
easily convert it to utilise the simplified i2c driver registration.

Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: i2c: s5c73m3: Convert to new i2c device probe()

The I2C core framework provides a simplified probe framework from commit
b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new() call-back type").

This driver does not utilise the i2c_device_id table in the probe, so we can
easily convert it to utilise the simplified i2c driver registration.

Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: i2c: smiapp: Convert to new i2c device probe()

The I2C core framework provides a simplified probe framework from commit
b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new() call-back type").

This driver does not utilise the i2c_device_id table in the probe, so we can
easily convert it to utilise the simplified i2c driver registration.

Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: radio: si470x: Convert to new i2c device probe()

The I2C core framework provides a simplified probe framework from commit
b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new() call-back type").

This driver does not utilise the i2c_device_id table in the probe, so we can
easily convert it to utilise the simplified i2c driver registration.

Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: radio: si4713: Convert to new i2c device probe()

The I2C core framework provides a simplified probe framework from commit
b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new() call-back type").

This driver does not utilise the i2c_device_id table in the probe, so we can
easily convert it to utilise the simplified i2c driver registration.

Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>