Olof Johansson [Sat, 11 Jan 2020 06:12:33 +0000 (22:12 -0800)]
Merge tag 'sunxi-fixes-for-5.5' of https://git./linux/kernel/git/sunxi/linux into arm/fixes
A couple of fixes for GPIO polarity and regulators on the A64
olinuxino.
* tag 'sunxi-fixes-for-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a83t: Correct USB3503 GPIOs polarity
arm64: dts: allwinner: a64: olinuxino: Fix SDIO supply regulator
arm64: dts: allwinner: a64: olinuxino: Fix eMMC supply regulator
Link: https://lore.kernel.org/r/582f4fda-38af-43e8-af58-957aee5b9dd8.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 11 Jan 2020 06:12:16 +0000 (22:12 -0800)]
Merge tag 'imx-fixes-5.5-2' of git://git./linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.5, round 2:
- Fix i.MX8MM SDMA1 AHB clock setting to remove a "Timeout waiting for CH0"
error seen with UART1.
- Correct compatible of RV3029 RTC device on imx6q-dhcom board.
- Correct interrupt trigger type for magnetometer on board
imx8mq-librem5-devkit.
- A series from Anson Huang to fix vdd3p0 power supplier for a few NXP
development board.
- Fix imx6q-icore-mipi board to use 1.5 version of i.Core MX6DL, so
that Ethernet interface on the board works properly.
- Fix Toradex Colibri board to get NAND flash support back.
- Fix SGTL5000 VDDIO regulator connection for imx6q-dhcom, which
is connected to PMIC SW2 output rather than a fixed 3V3 rail.
- Fix 'reg' of CPU node on imx7ulp to get rid of a warning given by
kernel.
- Fix endian setting for DCFG on LS1028A SoC, so that register access
of DCFG becomes correct.
* tag 'imx-fixes-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7: Fix Toradex Colibri iMX7S 256MB NAND flash support
ARM: dts: imx6sll-evk: Remove incorrect power supply assignment
ARM: dts: imx6sl-evk: Remove incorrect power supply assignment
ARM: dts: imx6sx-sdb: Remove incorrect power supply assignment
ARM: dts: imx6qdl-sabresd: Remove incorrect power supply assignment
ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL
arm64: dts: imx8mq-librem5-devkit: use correct interrupt for the magnetometer
ARM: dts: imx6q-dhcom: Fix SGTL5000 VDDIO regulator connection
ARM: dts: imx7ulp: fix reg of cpu node
arm64: dts: imx8mm: Change SDMA1 ahb clock for imx8mm
arm64: dts: ls1028a: fix endian setting for dcfg
ARM: dts: imx6q-dhcom: fix rtc compatible
Link: https://lore.kernel.org/r/20200110011836.GW4456@T480
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 11 Jan 2020 06:11:12 +0000 (22:11 -0800)]
Merge tag 'amlogic-fixes' of https://git./linux/kernel/git/khilman/linux-amlogic into arm/fixes
arm-soc: Amlogic fixes for v5.5-rc
* tag 'amlogic-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson-sm1-sei610: add gpio bluetooth interrupt
dt-bindings: reset: meson8b: fix duplicate reset IDs
soc: amlogic: meson-ee-pwrc: propagate errors from pm_genpd_init()
soc: amlogic: meson-ee-pwrc: propagate PD provider registration errors
ARM: dts: meson8: fix the size of the PMU registers
arm64: dts: meson-sm1-sei610: gpio-keys: switch to IRQs
Link: https://lore.kernel.org/r/7hmuaweavi.fsf@baylibre.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Marcel Ziswiler [Wed, 8 Jan 2020 16:12:31 +0000 (17:12 +0100)]
ARM: dts: imx7: Fix Toradex Colibri iMX7S 256MB NAND flash support
Turns out when introducing the eMMC version the gpmi node required for
NAND flash support got enabled exclusively on Colibri iMX7D 512MB.
Fixes:
f928a4a377e4 ("ARM: dts: imx7: add Toradex Colibri iMX7D 1GB (eMMC) support")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Mon, 30 Dec 2019 01:41:10 +0000 (09:41 +0800)]
ARM: dts: imx6sll-evk: Remove incorrect power supply assignment
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes:
96a9169cf621 ("ARM: dts: imx6sll-evk: Assign corresponding power supply for vdd3p0")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Mon, 30 Dec 2019 01:41:09 +0000 (09:41 +0800)]
ARM: dts: imx6sl-evk: Remove incorrect power supply assignment
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes:
3feea8805d6f ("ARM: dts: imx6sl-evk: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Mon, 30 Dec 2019 01:41:08 +0000 (09:41 +0800)]
ARM: dts: imx6sx-sdb: Remove incorrect power supply assignment
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes:
37a4bdead109 ("ARM: dts: imx6sx-sdb: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Mon, 30 Dec 2019 01:41:07 +0000 (09:41 +0800)]
ARM: dts: imx6qdl-sabresd: Remove incorrect power supply assignment
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes:
93385546ba36 ("ARM: dts: imx6qdl-sabresd: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Jagan Teki [Mon, 30 Dec 2019 12:00:19 +0000 (17:30 +0530)]
ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL
The EDIMM STARTER KIT i.Core 1.5 MIPI Evaluation is based on
the 1.5 version of the i.Core MX6 cpu module. The 1.5 version
differs from the original one for a few details, including the
ethernet PHY interface clock provider.
With this commit, the ethernet interface works properly:
SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver
While before using the 1.5 version, ethernet failed to startup
do to un-clocked PHY interface:
fec 2188000.ethernet eth0: could not attach to PHY
Similar fix has merged for i.Core MX6Q but missed to update for DL.
Fixes:
a8039f2dd089 ("ARM: dts: imx6dl: Add Engicam i.CoreM6 1.5 Quad/Dual MIPI starter kit support")
Cc: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Olof Johansson [Wed, 8 Jan 2020 18:24:48 +0000 (10:24 -0800)]
Merge tag 'aspeed-5.5-devicetree-fixes' of git://git./linux/kernel/git/joel/aspeed into arm/fixes
ASPEED device tree fixes for 5.5
Fixes for some badly applied patches that went in to 5.5. There is also
a fix for an incorrect i2c address.
* tag 'aspeed-5.5-devicetree-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed: rainier: Fix fan fault and presence
ARM: dts: aspeed: rainier: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Remove duplicate flash nodes
ARM: dts: aspeed: tacoma: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Fix fsi master node
ARM: dts: aspeed-g6: Fix FSI master location
Link: https://lore.kernel.org/r/CACPK8XcjazgORXNZBU1ECMukXG4HA8D9VeDxiSPifDk_iB7_dw@mail.gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Arnd Bergmann [Mon, 16 Dec 2019 13:21:26 +0000 (14:21 +0100)]
ARM: omap2plus: select RESET_CONTROLLER
With the new omap_prm driver added unconditionally, omap2 builds
fail when the reset controller subsystem is disabled:
drivers/soc/ti/omap_prm.o: In function `omap_prm_probe':
omap_prm.c:(.text+0x2d4): undefined reference to `devm_reset_controller_register'
Link: https://lore.kernel.org/r/20191216132132.3330811-1-arnd@arndb.de
Fixes:
3e99cb214f03 ("soc: ti: add initial PRM driver with reset control support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Arnd Bergmann [Tue, 10 Dec 2019 19:51:44 +0000 (20:51 +0100)]
ARM: davinci: select CONFIG_RESET_CONTROLLER
Selecting RESET_CONTROLLER is actually required, otherwise we
can get a link failure in the clock driver:
drivers/clk/davinci/psc.o: In function `__davinci_psc_register_clocks':
psc.c:(.text+0x9a0): undefined reference to `devm_reset_controller_register'
drivers/clk/davinci/psc-da850.o: In function `da850_psc0_init':
psc-da850.c:(.text+0x24): undefined reference to `reset_controller_add_lookup'
Link: https://lore.kernel.org/r/20191210195202.622734-1-arnd@arndb.de
Fixes:
f962396ce292 ("ARM: davinci: support multiplatform build for ARM v5")
Cc: <stable@vger.kernel.org> # v5.4
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Brandon Wyman [Fri, 22 Nov 2019 00:33:33 +0000 (18:33 -0600)]
ARM: dts: aspeed: rainier: Fix fan fault and presence
The PCA9552 used for fan fault and presence information is at address
61h, not 60h.
Fixes:
2efc118ce3c3 ("ARM: dts: aspeed: rainier: Add i2c devices")
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Joel Stanley [Thu, 2 Jan 2020 23:44:51 +0000 (10:44 +1100)]
ARM: dts: aspeed: rainier: Remove duplicate i2c busses
This is a revert of "ARM: dts: aspeed: rainier: Add i2c devices", which
was already applied to the tree.
Fixes:
9c44db7096e0 ("ARM: dts: aspeed: rainier: Add i2c devices")
Reviewed-by: Jim Wright <wrightj@linux.vnet.ibm.com>
Tested-by: Jim Wright <wrightj@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Joel Stanley [Mon, 23 Dec 2019 13:47:34 +0000 (00:47 +1100)]
ARM: dts: aspeed: tacoma: Remove duplicate flash nodes
This is a revert of "ARM: dts: aspeed: tacoma: Enable FMC and SPI
devices" which was already applied as part of "ARM: dts: aspeed: Add
Tacoma machine".
Fixes:
8737481e381c ("ARM: dts: aspeed: tacoma: Enable FMC and SPI devices")
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Joel Stanley [Mon, 23 Dec 2019 13:47:33 +0000 (00:47 +1100)]
ARM: dts: aspeed: tacoma: Remove duplicate i2c busses
This is a revert of "ARM: dts: aspeed: tacoma: Enable I2C busses", which
was already applied as part of "ARM: dts: aspeed: Add Tacoma machine".
Fixes:
606bcdde6724 ("ARM: dts: aspeed: tacoma: Enable I2C busses")
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Joel Stanley [Mon, 23 Dec 2019 13:47:32 +0000 (00:47 +1100)]
ARM: dts: aspeed: tacoma: Fix fsi master node
This was broken when applying "ARM: dts: aspeed: tacoma: Add
host FSI description".
Fixes:
a981c93300ef ("ARM: dts: aspeed: tacoma: Add host FSI description")
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Joel Stanley [Mon, 23 Dec 2019 13:47:35 +0000 (00:47 +1100)]
ARM: dts: aspeed-g6: Fix FSI master location
The FIS nodes were placed incorrectly in the device tree.
Fixes:
0fe4e304782c ("ARM: dts: aspeed-g6: Describe FSI masters")
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Olof Johansson [Tue, 7 Jan 2020 19:15:26 +0000 (11:15 -0800)]
Merge tag 'omap-for-v5.5/fixes-rc5' of git://git./linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.5-rc cycle
Here are few fixes for v5.5-rc cycle:
- Two corner case fixes related to ti-sysc driver clock issues
- Fixes for am57xx dts for pcie gpios
- Beagle-x15 regulator dts fix
- Fix for wkup_m3_ipc driver race
* tag 'omap-for-v5.5/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
soc: ti: wkup_m3_ipc: Fix race condition with rproc_boot
ARM: dts: beagle-x15-common: Model 5V0 regulator
ARM: dts: am571x-idk: Fix gpios property to have the correct gpio number
ARM: dts: am57xx-beagle-x15/am57xx-idk: Remove "gpios" for endpoint dt nodes
bus: ti-sysc: Fix iterating over clocks
ARM: OMAP2+: Fix ti_sysc_find_one_clockdomain to check for to_clk_hw_omap
Link: https://lore.kernel.org/r/pull-1578418121-413328@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 6 Jan 2020 17:20:40 +0000 (09:20 -0800)]
Merge tag 'tee-optee-fix-for-5.5' of git://git.linaro.org:/people/jens.wiklander/linux-tee into arm/fixes
Fix OP-TEE multi page dynamic shm pool alloc
* tag 'tee-optee-fix-for-5.5' of git://git.linaro.org:/people/jens.wiklander/linux-tee:
optee: Fix multi page dynamic shm pool alloc
Link: https://lore.kernel.org/r/20200103103710.GA3469@jax
Signed-off-by: Olof Johansson <olof@lixom.net>
Lubomir Rintel [Fri, 20 Dec 2019 07:14:43 +0000 (08:14 +0100)]
ARM: dts: mmp3: Fix the TWSI ranges
The register blocks don't occupy 4K. In fact, some blocks are packed
close to others and assuming they're 4K causes overlaps:
pxa2xx-i2c
d4033800.i2c: can't request region for resource
[mem 0xd4033800-0xd40347ff]
Link: https://lore.kernel.org/r/20191220071443.247183-1-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>
Lubomir Rintel [Wed, 18 Dec 2019 19:04:54 +0000 (20:04 +0100)]
clk: mmp2: Fix the order of timer mux parents
Determined empirically, no documentation is available.
The OLPC XO-1.75 laptop used parent 1, that one being VCTCXO/4 (65MHz), but
thought it's a VCTCXO/2 (130MHz). The mmp2 timer driver, not knowing
what is going on, ended up just dividing the rate as of
commit
f36797ee4380 ("ARM: mmp/mmp2: dt: enable the clock")'
Link: https://lore.kernel.org/r/20191218190454.420358-3-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Lubomir Rintel [Wed, 18 Dec 2019 19:04:53 +0000 (20:04 +0100)]
ARM: mmp: do not divide the clock rate
This was done because the clock driver returned the wrong rate, which is
fixed in "clk: mmp2: Fix the order of timer mux parents" patch.
Link: https://lore.kernel.org/r/20191218190454.420358-2-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>
Sumit Garg [Mon, 30 Dec 2019 13:22:40 +0000 (18:52 +0530)]
optee: Fix multi page dynamic shm pool alloc
optee_shm_register() expected pages to be passed as an array of page
pointers rather than as an array of contiguous pages. So fix that via
correctly passing pages as per expectation.
Fixes:
a249dd200d03 ("tee: optee: Fix dynamic shm pool allocations")
Reported-by: Vincent Cao <vincent.t.cao@intel.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Vincent Cao <vincent.t.cao@intel.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Angus Ainslie (Purism) [Mon, 23 Dec 2019 08:12:53 +0000 (09:12 +0100)]
arm64: dts: imx8mq-librem5-devkit: use correct interrupt for the magnetometer
The LSM9DS1 uses a high level interrupt.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Fixes:
eb4ea0857c83 ("arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Marek Vasut [Fri, 20 Dec 2019 09:11:24 +0000 (10:11 +0100)]
ARM: dts: imx6q-dhcom: Fix SGTL5000 VDDIO regulator connection
The SGTL5000 VDDIO is connected to the PMIC SW2 output, not to
a fixed 3V3 rail. Describe this correctly in the DT.
Fixes:
52c7a088badd ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Peng Fan [Wed, 18 Dec 2019 12:22:32 +0000 (12:22 +0000)]
ARM: dts: imx7ulp: fix reg of cpu node
According to arm cpus binding doc,
"
On 32-bit ARM v7 or later systems this property is
required and matches the CPU MPIDR[23:0] register
bits.
Bits [23:0] in the reg cell must be set to
bits [23:0] in MPIDR.
All other bits in the reg cell must be set to 0.
"
In i.MX7ULP, the MPIDR[23:0] is 0xf00, not 0, so fix it.
Otherwise there will be warning:
"DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map"
Fixes:
20434dc92c05 ("ARM: dts: imx: add common imx7ulp dtsi support")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adam Ford [Mon, 16 Dec 2019 11:15:30 +0000 (05:15 -0600)]
arm64: dts: imx8mm: Change SDMA1 ahb clock for imx8mm
Using SDMA1 with UART1 is causing a "Timeout waiting for CH0" error.
This patch changes to ahb clock from SDMA1_ROOT to AHB which
fixes the timeout error.
Fixes:
a05ea40eb384 ("arm64: dts: imx: Add i.mx8mm dtsi support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Yinbo Zhu [Fri, 13 Dec 2019 02:18:39 +0000 (10:18 +0800)]
arm64: dts: ls1028a: fix endian setting for dcfg
DCFG block uses little endian. Fix it so that register access becomes
correct.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Fixes:
8897f3255c9c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alexandre Belloni [Thu, 12 Dec 2019 23:08:14 +0000 (00:08 +0100)]
ARM: dts: imx6q-dhcom: fix rtc compatible
The only correct and documented compatible string for the rv3029 is
microcrystal,rv3029. Fix it up.
Fixes:
52c7a088badd ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Olof Johansson [Wed, 18 Dec 2019 18:39:10 +0000 (10:39 -0800)]
Merge tag 'socfpga_dts_fix_for_v5.5' of git://git./linux/kernel/git/dinguyen/linux into arm/fixes
arm64: dts: agilex/stratix10: fix pmu interrupt numbers
- Fix incorrect PMU interrupts numbers on the Agilex/Stratix10 platforms
* tag 'socfpga_dts_fix_for_v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: agilex/stratix10: fix pmu interrupt numbers
Link: https://lore.kernel.org/r/20191218161336.32377-1-dinguyen@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Dave Gerlach [Thu, 12 Dec 2019 04:03:14 +0000 (22:03 -0600)]
soc: ti: wkup_m3_ipc: Fix race condition with rproc_boot
Any user of wkup_m3_ipc calls wkup_m3_ipc_get to get a handle and this
checks the value of the static variable m3_ipc_state to see if the
wkup_m3 is ready. Currently this is populated during probe before
rproc_boot has been called, meaning there is a window of time that
wkup_m3_ipc_get can return a valid handle but the wkup_m3 itself is not
ready, leading to invalid IPC calls to the wkup_m3 and system
instability.
To avoid this, move the population of the m3_ipc_state variable until
after rproc_boot has succeeded to guarantee a valid and usable handle
is always returned.
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Kishon Vijay Abraham I [Tue, 17 Dec 2019 08:51:24 +0000 (14:21 +0530)]
ARM: dts: beagle-x15-common: Model 5V0 regulator
On am57xx-beagle-x15, 5V0 is connected to P16, P17, P18 and P19
connectors. On am57xx-evm, 5V0 regulator is used to get 3V6 regulator
which is connected to the COMQ port. Model 5V0 regulator here in order
for it to be used in am57xx-evm to model 3V6 regulator.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Kishon Vijay Abraham I [Tue, 17 Dec 2019 08:51:23 +0000 (14:21 +0530)]
ARM: dts: am571x-idk: Fix gpios property to have the correct gpio number
commit
d23f3839fe97d8dce03d ("ARM: dts: DRA7: Add pcie1 dt node for
EP mode") while adding the dt node for EP mode for DRA7 platform,
added rc node for am571x-idk and populated gpios property with
"gpio3 23". However the GPIO_PCIE_SWRST line is actually connected
to "gpio5 18". Fix it here. (The patch adding "gpio3 23" was tested
with another am57x board in EP mode which doesn't rely on reset from
host).
Cc: stable <stable@vger.kernel.org> # 4.14+
Fixes:
d23f3839fe97d8dce03d ("ARM: dts: DRA7: Add pcie1 dt node for EP mode")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Kishon Vijay Abraham I [Tue, 17 Dec 2019 08:51:22 +0000 (14:21 +0530)]
ARM: dts: am57xx-beagle-x15/am57xx-idk: Remove "gpios" for endpoint dt nodes
PERST# line in the PCIE connector is driven by the host mode and not
EP mode. The gpios property here is used for driving the PERST# line.
Remove gpios property from all endpoint device tree nodes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Marek Szyprowski [Wed, 11 Dec 2019 14:52:17 +0000 (15:52 +0100)]
ARM: dts: sun8i: a83t: Correct USB3503 GPIOs polarity
Current USB3503 driver ignores GPIO polarity and always operates as if the
GPIO lines were flagged as ACTIVE_HIGH. Fix the polarity for the existing
USB3503 chip applications to match the chip specification and common
convention for naming the pins. The only pin, which has to be ACTIVE_LOW
is the reset pin. The remaining are ACTIVE_HIGH. This change allows later
to fix the USB3503 driver to properly use generic GPIO bindings and read
polarity from DT.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Linus Torvalds [Tue, 17 Dec 2019 00:43:07 +0000 (16:43 -0800)]
Merge tag 'armsoc-fixes' of git://git./linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"I didn't get a batch in this weekend, so here's what we queued up last
week and today.
- A couple of defconfigs add back debugfs -- it used to be implicitly
enabled through CONFIG_TRACING, but
0e4a459f56c32d3e ("tracing:
Remove unnecessary DEBUG_FS dependency") removed that.
- The rest are mostly minor fixlets of the usual kind; some DT
tweaks, a headerfile refactor that needs a build fix now, etc"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (30 commits)
ARM: bcm: Add missing sentinel to bcm2711_compat[]
ARM: shmobile: defconfig: Restore debugfs support
bus: ti-sysc: Fix missing reset delay handling
ARM: imx: Fix boot crash if ocotp is not found
ARM: imx_v6_v7_defconfig: Explicitly restore CONFIG_DEBUG_FS
ARM: dts: imx6ul-evk: Fix peripheral regulator
arm64: dts: ls1028a: fix reboot node
ARM: mmp: include the correct cputype.h
ARM: dts: am437x-gp/epos-evm: fix panel compatible
arm64: dts: ls1028a: fix typo in TMU calibration data
ARM: imx: Correct ocotp id for serial number support of i.MX6ULL/ULZ SoCs
ARM: dts: bcm283x: Fix critical trip point
ARM: omap2plus_defconfig: Add back DEBUG_FS
ARM: omap2plus_defconfig: enable NET_SWITCHDEV
ARM: dts: am335x-sancloud-bbe: fix phy mode
bus: ti-sysc: Fix missing force mstandby quirk handling
reset: Do not register resource data for missing resets
reset: Fix {of,devm}_reset_control_array_get kerneldoc return types
reset: brcmstb: Remove resource checks
dt-bindings: reset: Fix brcmstb-reset example
...
Tony Lindgren [Mon, 16 Dec 2019 22:41:53 +0000 (14:41 -0800)]
bus: ti-sysc: Fix iterating over clocks
Commit
d878970f6ce1 ("bus: ti-sysc: Add separate functions for handling
clocks") separated handling of optional clocks from the main clocks, but
introduced an issue where we do not necessarily allocate a slot for both
fck and ick clocks, but still assume fixed slots for enumerating over the
clocks.
Let's fix the issue by ensuring we always have slots for both fck and ick
even if we don't use ick, and don't attempt to enumerate optional clocks
if not allocated.
In the long run we might want to simplify things a bit by only allocating
space only for the optional clocks as we have only few devices with
optional clocks.
Fixes:
d878970f6ce1 ("bus: ti-sysc: Add separate functions for handling clocks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Mon, 16 Dec 2019 22:41:53 +0000 (14:41 -0800)]
ARM: OMAP2+: Fix ti_sysc_find_one_clockdomain to check for to_clk_hw_omap
We must bail out early if the clock is not hw_omap. Otherwise we will
try to access invalid address with hwclk->clkdm_name:
Unable to handle kernel paging request at virtual address
ffffffff
Internal error: Oops: 27 [#1] ARM
...
(strcmp) from [<
c011b348>] (clkdm_lookup+0x40/0x60)
[<
c011b348>] (clkdm_lookup) from [<
c011cb84>] (ti_sysc_clkdm_init+0x5c/0x64)
[<
c011cb84>] (ti_sysc_clkdm_init) from [<
c03680a8>] (sysc_probe+0x948/0x117c)
[<
c03680a8>] (sysc_probe) from [<
c03d0af4>] (platform_drv_probe+0x48/0x98)
...
Fixes:
2b2f7def058a ("bus: ti-sysc: Add support for missing clockdomain handling")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dinh Nguyen [Wed, 20 Nov 2019 15:15:17 +0000 (09:15 -0600)]
arm64: dts: agilex/stratix10: fix pmu interrupt numbers
Fix up the correct interrupt numbers for the PMU unit on Agilex
and Stratix10.
Fixes:
78cd6a9d8e15 ("arm64: dts: Add base stratix 10 dtsi")
Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Olof Johansson [Mon, 16 Dec 2019 19:33:29 +0000 (11:33 -0800)]
Merge tag 'arm-soc/for-5.5/soc-fixes' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs machine fixes for
5.5-rc1, please pull the following:
- H. Nikolaus adds a missing sentinel entry to the BCM2711 machine
descriptor compatible array which would make multiplatform kernels fail
to boot
* tag 'arm-soc/for-5.5/soc-fixes' of https://github.com/Broadcom/stblinux:
ARM: bcm: Add missing sentinel to bcm2711_compat[]
Link: https://lore.kernel.org/r/20191216035701.15534-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 16 Dec 2019 19:33:13 +0000 (11:33 -0800)]
Merge tag 'samsung-fixes-5.5' of https://git./linux/kernel/git/krzk/linux into arm/fixes
Samsung fixes for v5.5
1. Restore debugfs support in exynos_defconfig (as now it is not
selected as dependency of tracing). Debugfs is required by systemd
and several tests.
2. Maintainers updates.
* tag 'samsung-fixes-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: exynos_defconfig: Restore debugfs support
MAINTAINERS: Include Samsung SoC serial driver in Samsung SoC entry
MAINTAINERS: Update Lukasz Luba's email address
Link: https://lore.kernel.org/r/20191215121316.32091-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 16 Dec 2019 19:33:04 +0000 (11:33 -0800)]
Merge tag 'renesas-fixes-for-v5.5-tag1' of git://git./linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas fixes for v5.5
- Restore debugfs support
* tag 'renesas-fixes-for-v5.5-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: shmobile: defconfig: Restore debugfs support
Link: https://lore.kernel.org/r/20191213213719.18122-1-geert+renesas@glider.be
Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Mon, 16 Dec 2019 18:06:04 +0000 (10:06 -0800)]
Merge tag 'linux-kselftest-5.5-rc2' of git://git./linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
- ftrace and safesetid test fixes from Masami Hiramatsu
- Kunit fixes from Brendan Higgins, Iurii Zaikin, and Heidi Fahim
- Kselftest framework fixes from SeongJae Park and Michael Ellerman
* tag 'linux-kselftest-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kselftest: Support old perl versions
kselftest/runner: Print new line in print of timeout log
selftests: Fix dangling documentation references to kselftest_module.sh
Documentation: kunit: add documentation for kunit_tool
Documentation: kunit: fix typos and gramatical errors
kunit: testing kunit: Bug fix in test_run_timeout function
fs/ext4/inode-test: Fix inode test on 32 bit platforms.
selftests: safesetid: Fix Makefile to set correct test program
selftests: safesetid: Check the return value of setuid/setgid
selftests: safesetid: Move link library to LDLIBS
selftests/ftrace: Fix multiple kprobe testcase
selftests/ftrace: Do not to use absolute debugfs path
selftests/ftrace: Fix ftrace test cases to check unsupported
selftests/ftrace: Fix to check the existence of set_ftrace_filter
Eric Auger [Tue, 26 Nov 2019 17:54:13 +0000 (18:54 +0100)]
iommu: fix KASAN use-after-free in iommu_insert_resv_region
In case the new region gets merged into another one, the nr list node is
freed. Checking its type while completing the merge algorithm leads to
a use-after-free. Use new->type instead.
Fixes:
4dbd258ff63e ("iommu: Revisit iommu_insert_resv_region() implementation")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reported-by: Qian Cai <cai@lca.pw>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Stable <stable@vger.kernel.org> #v5.3+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 16 Dec 2019 03:50:23 +0000 (19:50 -0800)]
Fix root mounting with no mount options
The "trivial conversion" in commit
cccaa5e33525 ("init: use do_mount()
instead of ksys_mount()") was totally broken, since it didn't handle the
case of a NULL mount data pointer. And while I had "tested" it (and
presumably Dominik had too) that bug was hidden by me having options.
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Reported-by: Ondřej Jirman <megi@xff.cz>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reported-and-tested-by: Borislav Petkov <bp@suse.de>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Tested-by: Eric Biggers <ebiggers@kernel.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Nikolaus Schaller [Sun, 15 Dec 2019 07:49:02 +0000 (08:49 +0100)]
ARM: bcm: Add missing sentinel to bcm2711_compat[]
commit
781fa0a95424 ("ARM: bcm: Add support for BCM2711 SoC")
breaks boot of many other platforms (e.g. OMAP or i.MX6) if
CONFIG_ARCH_BCM2835 is enabled in addition to some multiplatform
config (e.g. omap2plus_defconfig). The symptom is that the OMAP
based board does not show any activity beyond "Starting Kernel ..."
even with earlycon.
Reverting the mentioned commit makes it work again.
The real fix is to add the missing NULL sentinel to the
bcm2711_compat[] variable-length array.
Fixes:
781fa0a95424 ("ARM: bcm: Add support for BCM2711 SoC")
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Linus Torvalds [Sun, 15 Dec 2019 23:16:08 +0000 (15:16 -0800)]
Linux 5.5-rc2
Linus Torvalds [Sun, 15 Dec 2019 22:58:13 +0000 (14:58 -0800)]
Merge tag 'for-linus' of git://git./linux/kernel/git/rdma/rdma
Pull rdma fixes from Doug Ledford:
"A small collection of -rc fixes. Mostly. One API addition, but that's
because we wanted to use it in a fix. There's also a bug fix that is
going to render the 5.5 kernel's soft-RoCE driver incompatible with
all soft-RoCE versions prior, but it's required to actually implement
the protocol according to the RoCE spec and required in order for the
soft-RoCE driver to be able to successfully work with actual RoCE
hardware.
Summary:
- Update Steve Wise info
- Fix for soft-RoCE crc calculations (will break back compatibility,
but only with the soft-RoCE driver, which has had this bug since it
was introduced and it is an on-the-wire bug, but will make
soft-RoCE fully compatible with real RoCE hardware)
- cma init fixup
- counters oops fix
- fix for mlx4 init/teardown sequence
- fix for mkx5 steering rules
- introduce a cleanup API, which isn't a fix, but we want to use it
in the next fix
- fix for mlx5 memory management that uses API in previous patch"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/mlx5: Fix device memory flows
IB/core: Introduce rdma_user_mmap_entry_insert_range() API
IB/mlx5: Fix steering rule of drop and count
IB/mlx4: Follow mirror sequence of device add during device removal
RDMA/counter: Prevent auto-binding a QP which are not tracked with res
rxe: correctly calculate iCRC for unaligned payloads
Update mailmap info for Steve Wise
RDMA/cma: add missed unregister_pernet_subsys in init failure
Linus Torvalds [Sun, 15 Dec 2019 20:27:31 +0000 (12:27 -0800)]
Merge tag 'riscv/for-v5.5-rc2' of git://git./linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"Two minor build fixes:
- Fix builds of the ELF loader when built with 'make -j1' (nommu
only)
- Fix CONFIG_SOC_SIFIVE builds when CONFIG_TTY is disabled (found
during randconfig testing)"
* tag 'riscv/for-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: only select serial sifive if TTY is enabled
riscv: Fix build dependency for loader
Linus Torvalds [Sun, 15 Dec 2019 20:24:44 +0000 (12:24 -0800)]
Merge tag 'for-linus-5.5b-rc2-tag' of git://git./linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Two fixes: one for a resource accounting bug in some configurations
and a fix for another patch which went into rc1"
* tag 'for-linus-5.5b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: fix ballooned page accounting without hotplug enabled
xen-blkback: prevent premature module unload
Linus Torvalds [Sun, 15 Dec 2019 19:36:12 +0000 (11:36 -0800)]
Merge branch 'remove-ksys-mount-dup' of git://git./linux/kernel/git/brodo/linux
Pull ksys_mount() and ksys_dup() removal from Dominik Brodowski:
"This small series replaces all in-kernel calls to the
userspace-focused ksys_mount() and ksys_dup() with calls to
kernel-centric functions:
For each replacement of ksys_mount() with do_mount(), one needs to
verify that the first and third parameter (char *dev_name, char *type)
are strings allocated in kernelspace and that the fifth parameter
(void *data) is either NULL or refers to a full page (only occurence
in init/do_mounts.c::do_mount_root()). The second and fourth
parameters (char *dir_name, unsigned long flags) are passed by
ksys_mount() to do_mount() unchanged, and therefore do not require
particular care.
Moreover, instead of pretending to be userspace, the opening of
/dev/console as stdin/stdout/stderr can be implemented using in-kernel
functions as well. Thereby, ksys_dup() can be removed for good"
[ This doesn't get rid of the special "kernel init runs with KERNEL_DS"
case, but it at least removes _some_ of the users of "treat kernel
pointers as user pointers for our magical init sequence".
One day we'll hopefully be rid of it all, and can initialize our
init_thread addr_limit to USER_DS. - Linus ]
* 'remove-ksys-mount-dup' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux:
fs: remove ksys_dup()
init: unify opening /dev/console as stdin/stdout/stderr
init: use do_mount() instead of ksys_mount()
initrd: use do_mount() instead of ksys_mount()
devtmpfs: use do_mount() instead of ksys_mount()
Linus Torvalds [Sun, 15 Dec 2019 00:10:22 +0000 (16:10 -0800)]
Merge tag 'Wimplicit-fallthrough-5.5-rc2' of git://git./linux/kernel/git/gustavoars/linux
Pull fall through fix from Gustavo Silva:
"Fix compile error on sh by marking expected switch fall-through"
* tag 'Wimplicit-fallthrough-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
sh: kgdb: Mark expected switch fall-throughs
Linus Torvalds [Sat, 14 Dec 2019 20:51:57 +0000 (12:51 -0800)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"24 fixes, all in drivers. The lion's share (16) are qla2xxx and the
rest are iscsi (3), ufs (2), smarpqi, lpfc and libsas"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: iscsi: Avoid potential deadlock in iscsi_if_rx func
scsi: iscsi: Fix a potential deadlock in the timeout handler
scsi: smartpqi: Update attribute name to `driver_version`
scsi: libsas: stop discovering if oob mode is disconnected
scsi: ufs: Disable autohibern8 feature in Cadence UFS
scsi: iscsi: qla4xxx: fix double free in probe
scsi: ufs: Give an unique ID to each ufs-bsg
scsi: qla2xxx: Add debug dump of LOGO payload and ELS IOCB
scsi: qla2xxx: Ignore PORT UPDATE after N2N PLOGI
scsi: qla2xxx: Don't defer relogin unconditonally
scsi: qla2xxx: Send Notify ACK after N2N PLOGI
scsi: qla2xxx: Configure local loop for N2N target
scsi: qla2xxx: Fix PLOGI payload and ELS IOCB dump length
scsi: qla2xxx: Don't call qlt_async_event twice
scsi: qla2xxx: Allow PLOGI in target mode
scsi: qla2xxx: Change discovery state before PLOGI
scsi: qla2xxx: Drop superfluous INIT_WORK of del_work
scsi: qla2xxx: Initialize free_work before flushing it
scsi: qla2xxx: Use explicit LOGO in target mode
scsi: qla2xxx: Ignore NULL pointer in tcm_qla2xxx_free_mcmd
...
Linus Torvalds [Sat, 14 Dec 2019 20:49:20 +0000 (12:49 -0800)]
Merge tag 'char-misc-5.5-rc2' of git://git./linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are six small fixes for some reported char/misc driver issues:
- fix build warnings with new 'awk' with the raid6 code
- four interconnect driver bugfixes
- binder fix for reported problem
All of these except the binder fix have been in linux-next with no
reported issues. The binder fix is "new" but Todd says it is good as
he has tested it :)"
* tag 'char-misc-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
binder: fix incorrect calculation for num_valid
interconnect: qcom: msm8974: Walk the list safely on node removal
interconnect: qcom: qcs404: Walk the list safely on node removal
interconnect: qcom: sdm845: Walk the list safely on node removal
interconnect: qcom: Fix Kconfig indentation
lib: raid6: fix awk build warnings
Linus Torvalds [Sat, 14 Dec 2019 20:45:36 +0000 (12:45 -0800)]
Merge tag 'driver-core-5.5-rc2' of git://git./linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two small driver core fixes to resolve some reported issues
The first is to handle the much-reported (by the build systems)
problem that superH does not boot anymore.
The second handles an issue in the new platform logic that a number of
people ran into with the automated tests in kbuild
Both of these have been in linux-next with no reported issues"
* tag 'driver-core-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers: Fix boot problem on SuperH
of/platform: Unconditionally pause/resume sync state during kernel init
Linus Torvalds [Sat, 14 Dec 2019 20:43:57 +0000 (12:43 -0800)]
Merge tag 'staging-5.5-rc2' of git://git./linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are a number of small staging and IIO driver fixes for reported
issues for 5.5-rc2
Nothing major, a bunch of tiny IIO driver issues resolved, and some
staging driver fixes for things that people ran into with 5.5-rc1.
Full details are in the shortlog.
All of these have been in linux-next with no reported issues"
* tag 'staging-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (28 commits)
fbtft: Fix the initialization from property algorithm
staging: rtl8712: fix interface sanity check
staging: rtl8188eu: fix interface sanity check
staging: gigaset: add endpoint-type sanity check
staging: gigaset: fix illegal free on probe errors
staging: gigaset: fix general protection fault on probe
staging: vchiq: call unregister_chrdev_region() when driver registration fails
staging: exfat: fix multiple definition error of `rename_file'
staging/wlan-ng: add CRC32 dependency in Kconfig
staging: hp100: Fix build error without ETHERNET
staging: fbtft: Do not hardcode SPI CS polarity inversion
staging: exfat: properly support discard in clr_alloc_bitmap()
staging/octeon: Mark Ethernet driver as BROKEN
iio: adc: max9611: Fix too short conversion time delay
iio: ad7949: fix channels mixups
iio: imu: st_lsm6dsx: do not power-off accel if events are enabled
iio: imu: st_lsm6dsx: track hw FIFO buffering with fifo_mask
iio: imu: st_lsm6dsx: fix decimation factor estimation
iio: imu: inv_mpu6050: fix temperature reporting using bad unit
iio: humidity: hdc100x: fix IIO_HUMIDITYRELATIVE channel reporting
...
Linus Torvalds [Sat, 14 Dec 2019 20:40:39 +0000 (12:40 -0800)]
Merge tag 'usb-5.5-rc2' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB driver fixes for reported issues for 5.5-rc2
There's the usual gadget and xhci fixes, as well as some other
problems that syzbot has been finding during it's fuzzing runs. Full
details are in the shortlog.
All of these have been in linux-next with no reported issues"
* tag 'usb-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (21 commits)
usb: dwc3: pci: add ID for the Intel Comet Lake -H variant
xhci: make sure interrupts are restored to correct state
xhci: handle some XHCI_TRUST_TX_LENGTH quirks cases as default behaviour.
xhci: Increase STS_HALT timeout in xhci_suspend()
usb: xhci: only set D3hot for pci device
xhci: fix USB3 device initiated resume race with roothub autosuspend
xhci: Fix memory leak in xhci_add_in_port()
USB: Fix incorrect DMA allocations for local memory pool drivers
usb: gadget: fix wrong endpoint desc
usb: dwc3: ep0: Clear started flag on completion
usb: dwc3: gadget: Clear started flag for non-IOC
usb: dwc3: gadget: Fix logical condition
USB: atm: ueagle-atm: add missing endpoint check
USB: adutux: fix interface sanity check
USB: idmouse: fix interface sanity checks
USB: serial: io_edgeport: fix epic endpoint lookup
usb: mon: Fix a deadlock in usbmon between mmap and read
usb: common: usb-conn-gpio: Don't log an error on probe deferral
usb: core: urb: fix URB structure initialization function
usb: typec: fix use after free in typec_register_port()
...
Linus Torvalds [Sat, 14 Dec 2019 20:34:37 +0000 (12:34 -0800)]
Merge tag 's390-5.5-3' of git://git./linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Add support for KASAN_VMALLOC feature.
- Remove the last user of problematic diag 0x44 call.
- Adjust sampling interval and avoid sample data block overflow
condition on pressure in perf code.
- Prefer EOPNOTSUPP over ENOTSUPP and comments fixes.
* tag 's390-5.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/kasan: add KASAN_VMALLOC support
s390: remove last diag 0x44 caller
s390/uv: use EOPNOTSUPP instead of ENOTSUPP
s390/cpum_sf: Avoid SBD overflow condition in irq handler
s390/cpum_sf: Adjust sampling interval to avoid hitting sample limits
s390/test_unwind: fix spelling mistake "reqister" -> "register"
s390/spinlock: remove confusing comment in arch_spin_lock_wait
Linus Torvalds [Sat, 14 Dec 2019 20:32:28 +0000 (12:32 -0800)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"Fix another build problem for Wireguard without Crypto"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: arm/curve25519 - add arch-specific key generation function
Linus Torvalds [Sat, 14 Dec 2019 19:44:14 +0000 (11:44 -0800)]
Merge tag '5.5-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cfis fixes from Steve French:
"Three small smb3 fixes: this addresses two recent issues reported in
additional testing during rc1, a refcount underflow and a problem with
an intermittent crash in SMB2_open_init"
* tag '5.5-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Close cached root handle only if it has a lease
SMB3: Fix crash in SMB2_open_init due to uninitialized field in compounding path
smb3: fix refcount underflow warning on unmount when no directory leases
Linus Torvalds [Sat, 14 Dec 2019 19:13:54 +0000 (11:13 -0800)]
Merge tag 'ovl-fixes-5.5-rc2' of git://git./linux/kernel/git/mszeredi/vfs
Pull overlayfs fixes from Miklos Szeredi:
"Fix some bugs and documentation"
* tag 'ovl-fixes-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
docs: filesystems: overlayfs: Fix restview warnings
docs: filesystems: overlayfs: Rename overlayfs.txt to .rst
ovl: relax WARN_ON() on rename to self
ovl: fix corner case of non-unique st_dev;st_ino
ovl: don't use a temp buf for encoding real fh
ovl: make sure that real fid is 32bit aligned in memory
ovl: fix lookup failure on multi lower squashfs
Todd Kjos [Fri, 13 Dec 2019 20:25:31 +0000 (12:25 -0800)]
binder: fix incorrect calculation for num_valid
For BINDER_TYPE_PTR and BINDER_TYPE_FDA transactions, the
num_valid local was calculated incorrectly causing the
range check in binder_validate_ptr() to miss out-of-bounds
offsets.
Fixes:
bde4a19fc04f ("binder: use userspace pointer as base of buffer space")
Signed-off-by: Todd Kjos <tkjos@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191213202531.55010-1-tkjos@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Fri, 13 Dec 2019 23:05:00 +0000 (15:05 -0800)]
Merge tag 'nios2-v5.5-rc2' of git://git./linux/kernel/git/lftan/nios2
Pull nios2 fix from Ley Foon Tan:
"Fix nios2 ioremap regression"
* tag 'nios2-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
nios2: Fix ioremap
Linus Torvalds [Fri, 13 Dec 2019 23:03:25 +0000 (15:03 -0800)]
Merge tag 'devicetree-fixes-for-5.5' of git://git./linux/kernel/git/robh/linux
Pull Devicetree fixes from Rob Herring:
- Fix for dependency tracking caused by unittest interaction
- Fix some schema errors in Tegra memory controller schema
- Update Maxime Ripard's email address
- Review fixes to TI cpsw-switch
- Add wakeup-source prop for STM32 rproc. Got dropped in the schema
conversion.
* tag 'devicetree-fixes-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of/platform: Unconditionally pause/resume sync state during kernel init
dt-bindings: memory-controllers: tegra: Fix type references
dt-bindings: Change maintainer address
dt-bindings: net: ti: cpsw-switch: update to fix comments
dt-bindings: remoteproc: stm32: add wakeup-source property
Linus Torvalds [Fri, 13 Dec 2019 22:58:24 +0000 (14:58 -0800)]
Merge tag 'for_linus' of git://git./linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"Some fixes and cleanup patches"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_balloon: divide/multiply instead of shifts
virtio_balloon: name cleanups
virtio-balloon: fix managed page counts when migrating pages between zones
Linus Torvalds [Fri, 13 Dec 2019 22:52:03 +0000 (14:52 -0800)]
Merge tag 'pci-v5.5-fixes-1' of git://git./linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"Fix rockchip outbound ATU issue that prevented Google Kevin
Chromebooks from booting (Enric Balletbo i Serra)"
* tag 'pci-v5.5-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: rockchip: Fix IO outbound ATU register number
Linus Torvalds [Fri, 13 Dec 2019 22:45:40 +0000 (14:45 -0800)]
Merge branch 'i2c/for-next' of git://git./linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- removal of an old API where all in-kernel users have been converted
as of this merge window.
- a kdoc fix
- a new helper that will make dependencies for the next API conversion
a tad easier
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: add helper to check if a client has a driver attached
i2c: fix header file kernel-doc warning
i2c: remove i2c_new_dummy() API
Linus Torvalds [Fri, 13 Dec 2019 22:43:26 +0000 (14:43 -0800)]
Merge tag 'pm-5.5-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These add PM QoS support to devfreq and fix a few issues in that
subsystem, fix two cpuidle issues and do one minor cleanup in there,
and address an ACPI power management problem related to devices with
special power management requirements, like fans.
Specifics:
- Add PM QoS support, based on the frequency QoS introduced during
the 5.4 cycle, to devfreq (Leonard Crestez).
- Fix some assorted devfreq issues (Leonard Crestez).
- Fix an unintentional cpuidle behavior change (introduced during the
5.4 cycle) related to the active polling time limit (Marcelo
Tosatti).
- Fix a recently introduced cpuidle helper function and do a minor
cleanup in the cpuidle core (Rafael Wysocki).
- Avoid adding devices with special power management requirements,
like fans, to the generic ACPI PM domain (Rafael Wysocki)"
* tag 'pm-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: Drop unnecessary type cast in cpuidle_poll_time()
cpuidle: Fix cpuidle_driver_state_disabled()
ACPI: PM: Avoid attaching ACPI PM domain to certain devices
cpuidle: use first valid target residency as poll time
PM / devfreq: Use PM QoS for sysfs min/max_freq
PM / devfreq: Add PM QoS support
PM / devfreq: Don't fail devfreq_dev_release if not in list
PM / devfreq: Introduce get_freq_range helper
PM / devfreq: Set scaling_max_freq to max on OPP notifier error
PM / devfreq: Fix devfreq_notifier_call returning errno
Linus Torvalds [Fri, 13 Dec 2019 22:40:38 +0000 (14:40 -0800)]
Merge tag 'sound-5.5-rc2' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A small collection of fixes.
The main changes are fixes for a couple of regressions in AMD HD-audio
and FireWire that were introduced in 5.5-rc1. The rest are small fixes
for echoaudio and FireWire, as well as a usual Dell HD-audio fixup"
* tag 'sound-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Line-out jack doesn't work on a Dell AIO
ALSA: hda/hdmi - Fix duplicate unref of pci_dev
ALSA: fireface: fix return value in error path of isochronous resources reservation
ALSA: oxfw: fix return value in error path of isochronous resources reservation
ALSA: firewire-motu: fix double unlocked 'motu->mutex'
ALSA: echoaudio: simplify get_audio_levels
Linus Torvalds [Fri, 13 Dec 2019 22:36:45 +0000 (14:36 -0800)]
Merge tag 'drm-fixes-2019-12-13' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Usual round of rc2 fixes.
i915 and amdgpu leading the charge, but a few others in here,
including some nouveau fixes, all seems pretty for rc2, but hey it's a
Fri 13th pull so I'm sure it'll cause untold bad fortune.
dma-buf:
- memory leak fix
- expand MAINTAINERS scope
core:
- fix mode matching for drivers not using picture_aspect_ratio
nouveau:
- panel scaling fix
- MST BPC fix
- atomic fixes
i915:
- GPU hang on idle transition
- GLK+ FBC corruption fix
- non-priv OA access on Tigerlake
- HDCP state fix
- CI found race fixes
amdgpu:
- renoir DC fixes
- GFX8 fence flush alignment with userspace
- Arcturus power profile fix
- DC aux + i2c over aux fixes
- GPUVM invalidation semaphore fixes
- gfx10 golden registers update
mgag200:
- expand startadd fix
panfrost:
- devfreq fix
- memory fixes
mcde:
- DSI pointer deref fix"
* tag 'drm-fixes-2019-12-13' of git://anongit.freedesktop.org/drm/drm: (51 commits)
drm/amdgpu: add invalidate semaphore limit for SRIOV in gmc10
drm/amdgpu: add invalidate semaphore limit for SRIOV and picasso in gmc9
drm/amdgpu: avoid using invalidate semaphore for picasso
Revert "drm/amdgpu: dont schedule jobs while in reset"
drm/amdgpu: fix license on Kconfig and Makefiles
drm/amdgpu/gfx10: update gfx golden settings for navi14
drm/amdgpu/gfx10: update gfx golden settings
drm/amdgpu/gfx10: update gfx golden settings for navi14
drm/amdgpu/gfx10: update gfx golden settings
drm/i915: Serialise with remote retirement
drm/amd/display: include linux/slab.h where needed
drm/amd/display: fix undefined struct member reference
drm/nouveau/kms/nv50-: fix panel scaling
drm/nouveau/kms/nv50-: Limit MST BPC to 8
drm/nouveau/kms/nv50-: Store the bpc we're using in nv50_head_atom
drm/nouveau/kms/nv50-: Call outp_atomic_check_view() before handling PBN
drm/nouveau: Fix drm-core using atomic code-paths on pre-nv50 hardware
drm/nouveau: Move the declaration of struct nouveau_conn_atom up a bit
drm/i915/gt: Detect if we miss WaIdleLiteRestore
drm/i915/hdcp: Nuke intel_hdcp_transcoder_config()
...
Linus Torvalds [Fri, 13 Dec 2019 22:27:19 +0000 (14:27 -0800)]
Merge tag 'for-linus-
20191212' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- stable fix for the bi_size overflow. Not a corruption issue, but a
case wher we could merge but disallowed (Andreas)
- NVMe pull request via Keith, with various fixes.
- MD pull request from Song.
- Merge window regression fix for the rq passthrough stats (Logan)
- Remove unused blkcg_drain_queue() function (Guoqing)
* tag 'for-linus-
20191212' of git://git.kernel.dk/linux-block:
blk-cgroup: remove blkcg_drain_queue
block: fix NULL pointer dereference in account statistics with IDE
md: make sure desc_nr less than MD_SB_DISKS
md: raid1: check rdev before reference in raid1_sync_request func
raid5: need to set STRIPE_HANDLE for batch head
block: fix "check bi_size overflow before merge"
nvme/pci: Fix read queue count
nvme/pci Limit write queue sizes to possible cpus
nvme/pci: Fix write and poll queue types
nvme/pci: Remove last_cq_head
nvme: Namepace identification descriptor list is optional
nvme-fc: fix double-free scenarios on hw queues
nvme: else following return is not needed
nvme: add error message on mismatching controller ids
nvme_fc: add module to ops template to allow module references
nvmet-loop: Avoid preallocating big SGL for data
nvme-fc: Avoid preallocating big SGL for data
nvme-rdma: Avoid preallocating big SGL for data
Linus Torvalds [Fri, 13 Dec 2019 22:24:54 +0000 (14:24 -0800)]
Merge tag 'io_uring-5.5-
20191212' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
- A tweak to IOSQE_IO_LINK (also marked for stable) to allow links that
don't sever if the result is < 0.
This is mostly for linked timeouts, where if we ask for a pure
timeout we always get -ETIME. This makes links useless for that case,
hence allow a case where it works.
- Five minor optimizations to fix and improve cases that regressed
since v5.4.
- An SQTHREAD locking fix.
- A sendmsg/recvmsg iov assignment fix.
- Net fix where read_iter/write_iter don't honor IOCB_NOWAIT, and
subsequently ensuring that works for io_uring.
- Fix a case where for an invalid opcode we might return -EBADF instead
of -EINVAL, if the ->fd of that sqe was set to an invalid fd value.
* tag 'io_uring-5.5-
20191212' of git://git.kernel.dk/linux-block:
io_uring: ensure we return -EINVAL on unknown opcode
io_uring: add sockets to list of files that support non-blocking issue
net: make socket read/write_iter() honor IOCB_NOWAIT
io_uring: only hash regular files for async work execution
io_uring: run next sqe inline if possible
io_uring: don't dynamically allocate poll data
io_uring: deferred send/recvmsg should assign iov
io_uring: sqthread should grab ctx->uring_lock for submissions
io-wq: briefly spin for new work after finishing work
io-wq: remove worker->wait waitqueue
io_uring: allow unbreakable links
Linus Torvalds [Fri, 13 Dec 2019 22:13:15 +0000 (14:13 -0800)]
Merge tag 'for-5.5/dm-fixes' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix DM multipath by restoring full path selector functionality for
bio-based configurations that don't haave a SCSI device handler.
- Fix dm-btree removal to ensure non-root btree nodes have at least
(max_entries / 3) entries. This resolves userspace thin_check
utility's report of "too few entries in btree_node".
- Fix both the DM thin-provisioning and dm-clone targets to properly
flush the data device prior to metadata commit. This resolves the
potential for inconsistency across a power loss event when the data
device has a volatile writeback cache.
- Small documentation fixes to dm-clone and dm-integrity.
* tag 'for-5.5/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
docs: dm-integrity: remove reference to ARC4
dm thin: Flush data device before committing metadata
dm thin metadata: Add support for a pre-commit callback
dm clone: Flush destination device before committing metadata
dm clone metadata: Use a two phase commit
dm clone metadata: Track exact changes per transaction
dm btree: increase rebalance threshold in __rebalance2()
dm: add dm-clone to the documentation index
dm mpath: remove harmful bio-based optimization
Linus Torvalds [Fri, 13 Dec 2019 22:02:12 +0000 (14:02 -0800)]
Merge tag 'sizeof_field-v5.5-rc2' of git://git./linux/kernel/git/kees/linux
Pull FIELD_SIZEOF conversion from Kees Cook:
"A mostly mechanical treewide conversion from FIELD_SIZEOF() to
sizeof_field(). This avoids the redundancy of having 2 macros
(actually 3) doing the same thing, and consolidates on sizeof_field().
While "field" is not an accurate name, it is the common name used in
the kernel, and doesn't result in any unintended innuendo.
As there are still users of FIELD_SIZEOF() in -next, I will clean up
those during this coming development cycle and send the final old
macro removal patch at that time"
* tag 'sizeof_field-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
treewide: Use sizeof_field() macro
MIPS: OCTEON: Replace SIZEOF_FIELD() macro
Olof Johansson [Fri, 13 Dec 2019 20:43:33 +0000 (12:43 -0800)]
Merge tag 'omap-for-v5.5/fixes-rc1-signed' of git://git./linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omap variants for v5.5-rc1 cycle
This series of changes contains fixes for issues recently noticed:
- The ti-sysc interconnect target module driver needs fixes for
mstandby quirk handling and reset delay
- We need to configure am335x-sancloud-bbe to use rgmii-id mode because of
the phy changes done earlier
- NET_SWITCHDEV is no longer selected in Kconfig but a dependency and we
must enable CONFIG_NET_SWITCHDEV to have TI_CPSW_SWITCHDEV
- We are still relying on DEBUG_FS at least for PM configuration, let's
add it back
- We need to update compatible for am437x-gp/epos-evm because of the
recent changes to use generic panels
* tag 'omap-for-v5.5/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Fix missing reset delay handling
ARM: dts: am437x-gp/epos-evm: fix panel compatible
ARM: omap2plus_defconfig: Add back DEBUG_FS
ARM: omap2plus_defconfig: enable NET_SWITCHDEV
ARM: dts: am335x-sancloud-bbe: fix phy mode
bus: ti-sysc: Fix missing force mstandby quirk handling
Link: https://lore.kernel.org/r/pull-1576254925-709310@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Geert Uytterhoeven [Mon, 9 Dec 2019 10:13:27 +0000 (11:13 +0100)]
ARM: shmobile: defconfig: Restore debugfs support
Since commit
0e4a459f56c32d3e ("tracing: Remove unnecessary DEBUG_FS
dependency"), CONFIG_DEBUG_FS is no longer auto-enabled. This breaks
booting Debian 9, as systemd needs debugfs:
[FAILED] Failed to mount /sys/kernel/debug.
See 'systemctl status sys-kernel-debug.mount' for details.
[DEPEND] Dependency failed for Local File Systems.
...
You are in emergGive root password for maintenance
(or press Control-D to continue):
Fix this by enabling CONFIG_DEBUG_FS explicitly.
See also commit
18977008f44c66bd ("ARM: multi_v7_defconfig: Restore
debugfs support").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20191209101327.26571-1-geert+renesas@glider.be
Rafael J. Wysocki [Fri, 13 Dec 2019 09:29:45 +0000 (10:29 +0100)]
Merge branches 'pm-cpuidle' and 'acpi-pm'
* pm-cpuidle:
cpuidle: Drop unnecessary type cast in cpuidle_poll_time()
cpuidle: Fix cpuidle_driver_state_disabled()
cpuidle: use first valid target residency as poll time
* acpi-pm:
ACPI: PM: Avoid attaching ACPI PM domain to certain devices
Juergen Gross [Thu, 12 Dec 2019 14:17:50 +0000 (15:17 +0100)]
xen/balloon: fix ballooned page accounting without hotplug enabled
When CONFIG_XEN_BALLOON_MEMORY_HOTPLUG is not defined
reserve_additional_memory() will set balloon_stats.target_pages to a
wrong value in case there are still some ballooned pages allocated via
alloc_xenballooned_pages().
This will result in balloon_process() no longer be triggered when
ballooned pages are freed in batches.
Reported-by: Nicholas Tsirakis <niko.tsirakis@gmail.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Paul Durrant [Tue, 10 Dec 2019 14:53:05 +0000 (14:53 +0000)]
xen-blkback: prevent premature module unload
Objects allocated by xen_blkif_alloc come from the 'blkif_cache' kmem
cache. This cache is destoyed when xen-blkif is unloaded so it is
necessary to wait for the deferred free routine used for such objects to
complete. This necessity was missed in commit
14855954f636 "xen-blkback:
allow module to be cleanly unloaded". This patch fixes the problem by
taking/releasing extra module references in xen_blkif_alloc/free()
respectively.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Pavel Shilovsky [Tue, 10 Dec 2019 19:44:52 +0000 (11:44 -0800)]
CIFS: Close cached root handle only if it has a lease
SMB2_tdis() checks if a root handle is valid in order to decide
whether it needs to close the handle or not. However if another
thread has reference for the handle, it may end up with putting
the reference twice. The extra reference that we want to put
during the tree disconnect is the reference that has a directory
lease. So, track the fact that we have a directory lease and
close the handle only in that case.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Steve French [Tue, 10 Dec 2019 04:34:10 +0000 (22:34 -0600)]
SMB3: Fix crash in SMB2_open_init due to uninitialized field in compounding path
Ran into an intermittent crash in
SMB2_open_init+0x2f6/0x970
due to oparms.cifs_sb not being initialized when called from:
smb2_compound_op+0x45d/0x1690
Zero the whole oparms struct in the compounding path before setting up the
oparms so we don't risk any uninitialized fields.
Fixes:
fdef665ba44a ("smb3: fix mode passed in on create for modetosid mount option")
Signed-off-by: Steve French <stfrench@microsoft.com>
Acked-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Dave Airlie [Fri, 13 Dec 2019 04:50:01 +0000 (14:50 +1000)]
Merge tag 'drm-fixes-5.5-2019-12-12' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
drm-fixes-5.5-2019-12-12:
amdgpu:
- DC fixes for renoir
- Gfx8 fence flush align with mesa
- Power profile fix for arcturus
- Freesync fix
- DC I2c over aux fix
- DC aux defer fix
- GPU reset fix
- GPUVM invalidation semaphore fixes for PCO and SR-IOV
- Golden settings updates for gfx10
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212223211.8034-1-alexander.deucher@amd.com
Dave Airlie [Fri, 13 Dec 2019 04:44:08 +0000 (14:44 +1000)]
Merge tag 'drm-intel-fixes-2019-12-12' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix user reported issue #673: GPU hang on transition to idle
- Avoid corruption on the top of the screen on GLK+ by disabling FBC
- Fix non-privileged access to OA on Tigerlake
- Fix HDCP code not to touch global state when just computing commit
- Fix CI splat by saving irqstate around virtual_context_destroy
- Serialise context retirement possibly on another CPU
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212100759.GA22260@jlahtine-desk.ger.corp.intel.com
Dave Airlie [Fri, 13 Dec 2019 04:32:30 +0000 (14:32 +1000)]
Merge tag 'drm-misc-next-fixes-2019-12-12' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
-mgag200: more startadd mitigation (Thomas)
-panfrost: devfreq fix + several memory fixes (Steven, Boris)
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Steven Price <steven.price@arm.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212140145.GA145200@art_vandelay
Saravana Kannan [Mon, 9 Dec 2019 19:31:19 +0000 (11:31 -0800)]
of/platform: Unconditionally pause/resume sync state during kernel init
Commit
5e6669387e22 ("of/platform: Pause/resume sync state during init
and of_platform_populate()") paused/resumed sync state during init only
if Linux had parsed and populated a devicetree.
However, the check for that (of_have_populated_dt()) can change after
of_platform_default_populate_init() executes. One example of this is
when devicetree unittests are enabled. This causes an unmatched
pause/resume of sync state. To avoid this, just unconditionally
pause/resume sync state during init.
Fixes:
5e6669387e22 ("of/platform: Pause/resume sync state during init and of_platform_populate()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Rob Herring [Wed, 11 Dec 2019 14:51:01 +0000 (08:51 -0600)]
dt-bindings: memory-controllers: tegra: Fix type references
Json-schema requires a $ref to be under an 'allOf' if there are
additional constraints otherwise the additional constraints are
ignored. (Note that this behavior will be changed in draft8.)
Fixes:
641262f5e1ed ("dt-bindings: memory: Add binding for NVIDIA Tegra30 External Memory Controller")
Fixes:
785685b7a106 ("dt-bindings: memory: Add binding for NVIDIA Tegra30 Memory Controller")
Fixes:
8da65c377b21 ("dt-bindings: memory: tegra30: Convert to Tegra124 YAML")
Cc: Thierry Reding <treding@nvidia.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Maxime Ripard [Mon, 9 Dec 2019 09:32:48 +0000 (10:32 +0100)]
dt-bindings: Change maintainer address
While my email address has changed for a while, all the schemas I
contributed still have the old one unfortunately. Update it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Rob Herring <robh@kernel.org>
Yishai Hadas [Thu, 12 Dec 2019 10:02:37 +0000 (12:02 +0200)]
IB/mlx5: Fix device memory flows
Fix device memory flows so that only once there will be no live mmaped
VA to a given allocation the matching object will be destroyed.
This prevents a potential scenario that existing VA that was mmaped by
one process might still be used post its deallocation despite that it's
owned now by other process.
The above is achieved by integrating with IB core APIs to manage
mmap/munmap. Only once the refcount will become 0 the DM object and its
underlay area will be freed.
Fixes:
3b113a1ec3d4 ("IB/mlx5: Support device memory type attribute")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20191212100237.330654-3-leon@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
Yishai Hadas [Thu, 12 Dec 2019 10:02:36 +0000 (12:02 +0200)]
IB/core: Introduce rdma_user_mmap_entry_insert_range() API
Introduce rdma_user_mmap_entry_insert_range() API to be used once the
required key for the given entry should be in a given range.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20191212100237.330654-2-leon@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
Enric Balletbo i Serra [Wed, 11 Dec 2019 09:34:50 +0000 (10:34 +0100)]
PCI: rockchip: Fix IO outbound ATU register number
Since
62240a88004b ("PCI: rockchip: Drop storing driver private outbound
resource data), the offset calculation is wrong to access the register
number to program the IO outbound ATU.
Fix this by computing the ATU IO register number based on the number of MEM
registers, not the size of the IO region.
This causes 'synchronous external aborts' like the following:
mwifiex_pcie 0000:01:00.0: enabling device (0000 -> 0002)
mwifiex_pcie: PCI memory map Virt0:
00000000a573ad00 PCI memory map Virt2:
00000000783126c4
Internal error: synchronous external abort:
96000210 [#1] PREEMPT SMP
Modules linked in: mwifiex_pcie(+) mwifiex uvcvideo cfg80211 atmel_mxt_ts videobuf2_vmalloc ...
CPU: 2 PID: 269 Comm: systemd-udevd Not tainted 5.4.0+ #327
Hardware name: Google Kevin (DT)
pstate:
60000005 (nZCv daif -PAN -UAO)
pc : mwifiex_register_dev+0x264/0x3f8 [mwifiex_pcie]
lr : mwifiex_register_dev+0x150/0x3f8 [mwifiex_pcie]
sp :
ffff800012073860
x29:
ffff800012073860 x28:
ffff8000100a2e28
x27:
ffff8000118b6210 x26:
ffff800008f57458
x25:
ffff0000ecfda000 x24:
0000000000000001
x23:
ffff0000e9905080 x22:
ffff800008f5d000
x21:
ffff0000eecea078 x20:
ffff0000e9905080
x19:
ffff0000eecea000 x18:
0000000000000001
x17:
0000000000000000 x16:
0000000000000000
x15:
ffffffffffffffff x14:
ffff8000118998c8
x13:
ffff000000000000 x12:
0000000000000008
x11:
0101010101010101 x10:
ffff7f7fffff7fff
x9 :
0000000000000000 x8 :
ffff0000e3c24240
x7 :
0000000000000000 x6 :
ffff0000e3c24148
x5 :
ffff0000e3c24148 x4 :
ffff0000e7975ec8
x3 :
0000000000000001 x2 :
0000000000002b42
x1 :
ffff800012c00008 x0 :
ffff0000e9905080
Call trace:
mwifiex_register_dev+0x264/0x3f8 [mwifiex_pcie]
mwifiex_add_card+0x2f8/0x430 [mwifiex]
mwifiex_pcie_probe+0x98/0x148 [mwifiex_pcie]
pci_device_probe+0x110/0x1a8
...
Code:
a8c67bfd d65f03c0 f942ac01 91002021 (
b9400021)
Suggested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Fixes:
62240a88004b ("PCI: rockchip: Drop storing driver private outbound resource data)
Link: https://lore.kernel.org/r/20191211093450.7481-1-enric.balletbo@collabora.com
Reported-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reported-by: Vicente Bergas <vicencb@gmail.com>
Tested-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andrew Murray <andrew.murray@arm.com>
changzhu [Tue, 10 Dec 2019 14:50:16 +0000 (22:50 +0800)]
drm/amdgpu: add invalidate semaphore limit for SRIOV in gmc10
It may fail to load guest driver in round 2 when using invalidate
semaphore for SRIOV. So it needs to avoid using invalidate semaphore
for SRIOV.
Signed-off-by: changzhu <Changfeng.Zhu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
changzhu [Tue, 10 Dec 2019 14:00:59 +0000 (22:00 +0800)]
drm/amdgpu: add invalidate semaphore limit for SRIOV and picasso in gmc9
It may fail to load guest driver in round 2 or cause Xstart problem
when using invalidate semaphore for SRIOV or picasso. So it needs avoid
using invalidate semaphore for SRIOV and picasso.
Signed-off-by: changzhu <Changfeng.Zhu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Maor Gottlieb [Thu, 12 Dec 2019 09:12:14 +0000 (11:12 +0200)]
IB/mlx5: Fix steering rule of drop and count
There are two flow rule destinations: QP and packet. While users are
setting DROP packet rule, the QP should not be set as a destination.
Fixes:
3b3233fbf02e ("IB/mlx5: Add flow counters binding support")
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20191212091214.315005-4-leon@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
Parav Pandit [Thu, 12 Dec 2019 09:12:13 +0000 (11:12 +0200)]
IB/mlx4: Follow mirror sequence of device add during device removal
Current code device add sequence is:
ib_register_device()
ib_mad_init()
init_sriov_init()
register_netdev_notifier()
Therefore, the remove sequence should be,
unregister_netdev_notifier()
close_sriov()
mad_cleanup()
ib_unregister_device()
However it is not above.
Hence, make do above remove sequence.
Fixes:
fa417f7b520ee ("IB/mlx4: Add support for IBoE")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20191212091214.315005-3-leon@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
Mark Zhang [Thu, 12 Dec 2019 09:12:12 +0000 (11:12 +0200)]
RDMA/counter: Prevent auto-binding a QP which are not tracked with res
Some QPs (e.g. XRC QP) are not tracked in kernel, in this case they have
an invalid res and should not be bound to any dynamically-allocated
counter in auto mode.
This fixes below call trace:
BUG: kernel NULL pointer dereference, address:
0000000000000390
PGD
80000001a7233067 P4D
80000001a7233067 PUD
1a7215067 PMD 0
Oops: 0000 [#1] SMP PTI
CPU: 2 PID: 24822 Comm: ibv_xsrq_pingpo Not tainted 5.4.0-rc5+ #21
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-2.fc27 04/01/2014
RIP: 0010:rdma_counter_bind_qp_auto+0x142/0x270 [ib_core]
Code: e1 48 85 c0 48 89 c2 0f 84 bc 00 00 00 49 8b 06 48 39 42 48 75 d6 40 3a aa 90 00 00 00 75 cd 49 8b 86 00 01 00 00 48 8b 4a 28 <8b> 80 90 03 00 00 39 81 90 03 00 00 75 b4 85 c0 74 b0 48 8b 04 24
RSP: 0018:
ffffc900003f39c0 EFLAGS:
00010246
RAX:
0000000000000000 RBX:
0000000000000001 RCX:
0000000000000000
RDX:
ffff88820020ec00 RSI:
0000000000000004 RDI:
ffffffffffffffc0
RBP:
0000000000000001 R08:
ffff888224149ff0 R09:
ffffc900003f3968
R10:
ffffffffffffffff R11:
ffff8882249c5848 R12:
ffffffffffffffff
R13:
ffff88821d5aca50 R14:
ffff8881f7690800 R15:
ffff8881ff890000
FS:
00007fe53a3e1740(0000) GS:
ffff888237b00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000000000390 CR3:
00000001a7292006 CR4:
00000000003606a0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
_ib_modify_qp+0x3a4/0x3f0 [ib_core]
? lookup_get_idr_uobject.part.8+0x23/0x40 [ib_uverbs]
modify_qp+0x322/0x3e0 [ib_uverbs]
ib_uverbs_modify_qp+0x43/0x70 [ib_uverbs]
ib_uverbs_handler_UVERBS_METHOD_INVOKE_WRITE+0xb1/0xf0 [ib_uverbs]
ib_uverbs_run_method+0x6be/0x760 [ib_uverbs]
? uverbs_disassociate_api+0xd0/0xd0 [ib_uverbs]
ib_uverbs_cmd_verbs+0x18d/0x3a0 [ib_uverbs]
? get_acl+0x1a/0x120
? __alloc_pages_nodemask+0x15d/0x2c0
ib_uverbs_ioctl+0xa7/0x110 [ib_uverbs]
do_vfs_ioctl+0xa5/0x610
ksys_ioctl+0x60/0x90
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x48/0x110
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes:
99fa331dc862 ("RDMA/counter: Add "auto" configuration mode support")
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Ido Kalir <idok@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20191212091214.315005-2-leon@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
Linus Torvalds [Thu, 12 Dec 2019 18:56:37 +0000 (10:56 -0800)]
Merge tag 'ceph-for-5.5-rc2' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A fix to avoid a corner case when scheduling cap reclaim in batches
from Xiubo, a patch to add some observability into cap waiters from
Jeff and a couple of cleanups"
* tag 'ceph-for-5.5-rc2' of git://github.com/ceph/ceph-client:
ceph: add more debug info when decoding mdsmap
ceph: switch to global cap helper
ceph: trigger the reclaim work once there has enough pending caps
ceph: show tasks waiting on caps in debugfs caps file
ceph: convert int fields in ceph_mount_options to unsigned int
Dominik Brodowski [Tue, 23 Oct 2018 14:24:09 +0000 (16:24 +0200)]
fs: remove ksys_dup()
ksys_dup() is used only at one place in the kernel, namely to duplicate
fd 0 of /dev/console to stdout and stderr. The same functionality can be
achieved by using functions already available within the kernel namespace.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Dominik Brodowski [Tue, 23 Oct 2018 14:00:10 +0000 (16:00 +0200)]
init: unify opening /dev/console as stdin/stdout/stderr
Merge the two instances where /dev/console is opened as
stdin/stdout/stderr.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Olof Johansson [Thu, 12 Dec 2019 17:38:22 +0000 (09:38 -0800)]
Merge tag 'imx-fixes-5.5' of git://git./linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.5:
- Add missing jedec,spi-nor compatible for imx6ul-14x14-evk board,
so that SPI NOR device can be probed.
- Fix power button of E60K02 board by removing LDORTC2 regulator.
- A couple of fixes on serial number support of i.MX6ULL/ULZ SoCs to
remove the boot regression caused by
8267ff89b713 ("ARM: imx: Add
serial number support for i.MX6/7 SoCs").
- A couple of fixes on LS1028A SoC TMU regarding to calibration data
and reboot register configuration.
- Fix a regression seen on imx6ul-evk board by marking always-on for
the regulator that is shared by many peripherals.
- Explicitly restore CONFIG_DEBUG_FS in imx_v6_v7_defconfig.
* tag 'imx-fixes-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: Fix boot crash if ocotp is not found
ARM: imx_v6_v7_defconfig: Explicitly restore CONFIG_DEBUG_FS
ARM: dts: imx6ul-evk: Fix peripheral regulator
arm64: dts: ls1028a: fix reboot node
arm64: dts: ls1028a: fix typo in TMU calibration data
ARM: imx: Correct ocotp id for serial number support of i.MX6ULL/ULZ SoCs
ARM: dts: e60k02: fix power button
ARM: dts: imx6ul: imx6ul-14x14-evk.dtsi: Fix SPI NOR probing
Link: https://lore.kernel.org/r/20191212122427.GK15858@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>