John W. Linville [Mon, 30 Jan 2012 15:53:55 +0000 (10:53 -0500)]
ath9k: use WARN_ON_ONCE in ath_rc_get_highest_rix
The device seems to survive the issue, so no need to flood the logs
about it...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yogesh Ashok Powar [Fri, 27 Jan 2012 10:38:27 +0000 (16:08 +0530)]
mwl8k: Configuring correct MAC address in broadcast key
While configuring the broadcast key in the hardware, in
multi-BSS environment, BSSes other than first were
incorrectly configured with the MAC address of first
BSS. Fixing it with correct MAC addresses.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nicolas Cavallari [Thu, 26 Jan 2012 12:36:34 +0000 (13:36 +0100)]
mac80211: Do not scan for IBSS merge with a fixed BSSID.
Currently, when we are on an IBSS network with no active station,
we would scan for other BSSID, even if fixed_bssid is on, due to
a bug in ibss.c, where fixed_channel would be checked instead of
fixed_bssid. This would trigger useless scans where scan results
would not be used anyway.
This patch also reverts commit
39d02a7d90602d4557ee05db2a157a4e0,
which assumed that the ifibss->fixed_channel check was legitimate
to disable single-channel scans. IBSS single-channel scan should
now be fixed.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Thu, 26 Jan 2012 11:36:05 +0000 (13:36 +0200)]
mac80211: send null packet on active (psm) reconfiguration
The sta might be in psm against the ap (e.g. because
this was the before a hw restart), so we explicitly
send a null packet in order to make sure it'll
sync against the ap (and get out of psm).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Thu, 26 Jan 2012 06:13:31 +0000 (09:13 +0300)]
nfc: NULL vs zero in nci_activate_target()
This is a pointer so it should be NULL instead of zero. Sparse
complains about this stuff:
net/nfc/nci/core.c:447:37: warning: Using plain integer as NULL pointer
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Wed, 25 Jan 2012 04:50:25 +0000 (20:50 -0800)]
mwifiex: update BSS parameters in dump_station_info()
This enables user to check beacon interval, DTIM period, short slot
time and short preamble information using "iw dev mlan0 link" command
when station is in connected state.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Wed, 25 Jan 2012 04:50:24 +0000 (20:50 -0800)]
mwifiex: pass priv pointer instead of adapter
Pass mwifiex_private pointer directly to wmm_add_buf_txqueue()
instead of passing adapter and then deriving priv again in
mwifiex_get_priv_by_id(). This reduces a 'for' loop in TX path.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Tue, 24 Jan 2012 13:09:09 +0000 (14:09 +0100)]
rt2800usb: remove PWR_PIN_CFG=0x3 during init
This seems to be only needed as workaround for hardware problem on
PCI devices.
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Tue, 24 Jan 2012 13:09:08 +0000 (14:09 +0100)]
rt2800: zero MAC_SYS_CTRL bits during BBP and MAC reset
Zero all other bits than RESET_CSR and RESET_BBP when want to do the
reset, that the vendor driver behaviour.
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Tue, 24 Jan 2012 13:09:07 +0000 (14:09 +0100)]
rt2800: disable DMA after firmware load
We can receive frames just after firmware load with current code, so
disable DMA just after firmware is loaded, not before.
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Tue, 24 Jan 2012 13:09:06 +0000 (14:09 +0100)]
rt2800usb: initialize H2M_INT_SRC register
Ralink USB driver initialize H2M_INT_SRC to 0 after firmware load, and
never touch this register later. It is not touched at all by Ralink PCI
driver.
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Randy Dunlap [Sat, 21 Jan 2012 19:03:00 +0000 (11:03 -0800)]
kernel-doc: fix new warnings in cfg80211.h
Fix new kernel-doc warnings:
Warning(include/net/cfg80211.h:1165): No description found for parameter 'channel_type'
Warning(include/net/cfg80211.h:2090): No description found for parameter 'probe_resp_offload'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christian Lamparter [Sat, 21 Jan 2012 15:59:10 +0000 (16:59 +0100)]
carl9170: allow users to lower output power level
This patch implements a simple way of reducing the
output power of the device by a configurable upper
limit.
Requested-by: Harshal Chhaya <harshal@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chun-Yeow Yeoh [Fri, 20 Jan 2012 17:02:16 +0000 (01:02 +0800)]
{nl,cfg,mac}80211: Add support of setting non-forwarding entity in Mesh
A mesh node that joins the mesh network is by default a forwarding entity. This patch allows
the mesh node to set as non-forwarding entity. Whenever dot11MeshForwarding is set to 0, the
mesh node can prevent itself from forwarding the traffic which is not destined to him.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 20 Jan 2012 12:52:37 +0000 (13:52 +0100)]
cfg80211: fix a few -Wshadow warnings
It seems that -Wshadow is no longer default in
sparse runs, but let's fix the warnings anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 20 Jan 2012 12:52:36 +0000 (13:52 +0100)]
mac80211: fix a few -Wshadow warnings
It seems that -Wshadow is no longer default in
sparse runs, but let's fix the warnings anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 19 Jan 2012 08:29:58 +0000 (09:29 +0100)]
mac80211: make CQM RSSI support per virtual interface
Similar to the previous beacon filtering patch,
make CQM RSSI support depend on the flags that
the driver set for virtual interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 19 Jan 2012 08:29:57 +0000 (09:29 +0100)]
mac80211: make beacon filtering per virtual interface
Due to firmware limitations, we may not be able to
support beacon filtering on all virtual interfaces.
To allow this in mac80211, introduce per-interface
driver capability flags that the driver sets when
an interface is added.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 24 Jan 2012 20:03:04 +0000 (15:03 -0500)]
orinoco_usb: remove version definition
Avoids this:
CC [M] drivers/net/wireless/orinoco/orinoco_usb.o
drivers/net/wireless/orinoco/orinoco_usb.c:1759:13: warning: ‘version’ defined but not used
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 24 Jan 2012 19:58:47 +0000 (14:58 -0500)]
ath5k: use bool type for no_hw_rfkill_switch module parameter
Avoids this:
CC [M] drivers/net/wireless/ath/ath5k/base.o
drivers/net/wireless/ath/ath5k/base.c: In function ‘__check_no_hw_rfkill_switch’:
drivers/net/wireless/ath/ath5k/base.c:85:1: warning: return from incompatible pointer type
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Antonio Quartulli [Tue, 17 Jan 2012 22:13:30 +0000 (23:13 +0100)]
ath9k_htc: claim support for IBSS RSN
Skip group keys configuration in hardware in order to make IBSS RSN work.
Keys will be managed using software.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ilan Elias [Wed, 18 Jan 2012 11:16:14 +0000 (13:16 +0200)]
NFC: Add NCI multiple targets support
Add the ability to select between multiple targets in NCI.
If only one target is found, it will be auto-activated.
If more than one target is found, then DISCOVER_NTF will be
generated for each target, and the host should select one by
calling DISCOVER_SELECT_CMD. Then, the target will be activated.
If the activation fails, GENERIC_ERROR_NTF is generated.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ilan Elias [Wed, 18 Jan 2012 11:16:13 +0000 (13:16 +0200)]
NFC: NFC core layer should not set the target_idx
The NFC core layer should not set the target_idx.
Instead, the driver layer (e.g. NCI, PN533) should set the
target_idx, so that it will be able to identify the target
when its I/F (e.g. activate_target) is called.
This is required in order to support multiple targets.
Note that currently supported drivers (PN533 and NCI) don't
use the target_idx in their implementation.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ilan Elias [Wed, 18 Jan 2012 11:16:12 +0000 (13:16 +0200)]
NFC: Clearly separate NCI states from flags
Make a clear separation between NCI states and flags.
This is required in order to support more NCI states (e.g.
for multiple targets support).
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Antonio Quartulli [Tue, 17 Jan 2012 23:10:44 +0000 (00:10 +0100)]
mac80211: in IBSS use the Auth frame to trigger STA reinsertion
In case of a node re-joining the cell the sta_info structure belonging to it is
first destroyed and then reinserted. In this way its internal state is reset.
The joining operation is recognised thank the Auth frame being received.
This operation is helpful in case of a node being rebooted that is joining the
ad-hoc cell again, before its purge timeout on other nodes expires.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Antonio Quartulli [Tue, 17 Jan 2012 23:10:43 +0000 (00:10 +0100)]
mac80211: add a 2-way Authentication challenge to IBSS mode
In IBSS mode, whenever a new station is added a 2-way authentication challenge
is performed. Actually this event can be used to recognise a new station joining
the cell even if its sta_info entry is already in the list.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ilan Elias [Tue, 17 Jan 2012 12:11:33 +0000 (14:11 +0200)]
NFC: Free sk_buff if nfcwilink_send fails
Free sk_buff if nfcwilink_send fails.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ilan Elias [Tue, 17 Jan 2012 12:11:32 +0000 (14:11 +0200)]
NFC: Download TI NFC init script
Download TI NFC init script during nfcwilink open operation,
after the NFC channel is registered with TI shared transport.
TI NFC init script is written in BTS format.
First, read the chip version via a special vendor specific command.
Second, we request the relevant BTS file from the user space, and
then send the BTS commands to the chip.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ilan Elias [Tue, 17 Jan 2012 12:11:31 +0000 (14:11 +0200)]
NFC: Add endian annotations to nfcwilink driver
Add endian annotations to TI nfcwilink driver.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ilan Elias [Tue, 17 Jan 2012 10:03:50 +0000 (12:03 +0200)]
NFC: Add NCI data exchange timer
Add NCI data exchange timer to catch timeouts,
and call the data exchange callback with an error.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 17 Jan 2012 09:33:29 +0000 (10:33 +0100)]
mac80211: clean up rate control code
It seems exceedingly unlikely that we'll ever
support swapping rate control algorithms at
runtime, so remove the unused refcounting code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 17 Jan 2012 09:30:01 +0000 (10:30 +0100)]
mac80211: clean up aggregation destruction
Yogesh's patch to destroy aggregation sessions when
stations are destroyed was needed, but unnecessarily
complex. Clean up this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ilan Elias [Tue, 17 Jan 2012 09:06:43 +0000 (11:06 +0200)]
NFC: Export new attributes sensb_res and sensf_res
Export new attributes sensb_res for tech B and sensf_res
for tech F in the target info (returned as a response to
NFC_CMD_GET_TARGET).
The max size of the attributes nfcid1, sensb_res and sensf_res
is exported to user space though include/linux/nfc.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Sun, 15 Jan 2012 08:38:45 +0000 (00:38 -0800)]
brcmfmac: Trivial typo of "couldn" to "could" fix
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Sun, 15 Jan 2012 08:38:44 +0000 (00:38 -0800)]
brcm80211: Use pr_fmt and pr_<level>
Convert printks to pr_<level>
Prefix logging with pr_fmt.
Use ##__VA_ARGS__ in some WL_ logging macros.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Sun, 15 Jan 2012 08:38:43 +0000 (00:38 -0800)]
brcm80211: Use brcmu_dbg_hex_dump
Convert a couple of pr_debug/print_hex_dump to
the standard utility.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Sun, 15 Jan 2012 08:38:42 +0000 (00:38 -0800)]
brcm80211: Convert printk(KERN_DEBUG to pr_debug
Use pr_debug to allow dynamic debugging to work.
Move an #endif to allow brcmf_dbg_hex_dump
to be outside the #if/#endif block.
Move a const char* declaration to be inside a
pr_debug so the function doesn't need a #if/#endif
block.
Don't use temporaries in debugging functions so
the code can be optimized away.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Sun, 15 Jan 2012 08:38:41 +0000 (00:38 -0800)]
brcmfmac: Remove useless #ifdef DEBUG
This doesn't do anything anymore.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Sun, 15 Jan 2012 08:38:40 +0000 (00:38 -0800)]
brcm80211: Add and use brcmX_dbg_dump_hex
Reduce the number of #ifdef DEBUG uses by
adding a dbg_hex_dump routine which has the
appropriate #ifdef DEBUG test.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Sun, 15 Jan 2012 08:38:39 +0000 (00:38 -0800)]
brcmfmac: Convert printk(KERN_DEBUG to pr_debug
Allow dynamic debugging.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Sun, 15 Jan 2012 08:38:38 +0000 (00:38 -0800)]
brcm80211: Use normal DEBUG define
Current CONFIG_BRCMDBG flag when enabled does not
necessarily enable proper pr_debug output when
DEBUG is not also enabled.
Remove BCMDBG define and just use DEBUG instead.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Antonio Quartulli [Sat, 14 Jan 2012 10:42:43 +0000 (11:42 +0100)]
ath5k: claim support for IBSS RSN
Disable group keys programming when using IBSS RSN. Keys will be managed using
software. In this way IBSS RSN can correctly work.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christian Lamparter [Fri, 13 Jan 2012 15:35:05 +0000 (16:35 +0100)]
carl9170: remove eeprom data injection option
In the early days, this was a quite useful software
feature for testing different regdomains and chain
configurations without adding debugfs cruft into
the driver. Nowadays, the driver's phy code seems
to be stable and there's no need for it anymore.
Therefore I decided to removed altogether.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Antonio Quartulli [Fri, 13 Jan 2012 12:53:18 +0000 (13:53 +0100)]
mac80211: remove useless DA checking in ieee80211_rx_mgmt_probe_resp()
Actually the DA field has already been checked along the rx path (in
prepare_for_handlers()) and this check is therefore useless at this point.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yogesh Ashok Powar [Thu, 12 Jan 2012 04:06:12 +0000 (20:06 -0800)]
mwifiex: derive priv from net_device instead of wiphy
Currently mwifiex_private pointers are derived from wiphy
structures. This will always work as long as there is only
one net_device associated with one wiphy. In scenarios where
there are multiple net_devices associated with single
wiphy, one should use net_device to derive the priv.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yogesh Ashok Powar [Thu, 12 Jan 2012 04:06:11 +0000 (20:06 -0800)]
mwifiex: use bss_type and bss_num to retrieve priv
Current implementation, for retrieving priv from adapter,
uses bss_index. In multi interface environment supporting
different types, bss_index may not be unique.
Use bss_type along with bss_num to retrieve the priv.
bss_index is removed with this change.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Wed, 11 Jan 2012 20:39:32 +0000 (14:39 -0600)]
bcma: Enable logging of SPROM offset
The SPROM location has been relocated again for some devices. This patch
will log the offset when CONFIG_BCMA_DEBUG has been selected.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hong Wu [Wed, 11 Jan 2012 18:34:30 +0000 (20:34 +0200)]
mac80211: Fix the maximum transmit power with power constraint
The local maximum transmit power for a channel is defined as the maximum
regulatory transmission power minus the local power constraint specified
for the channel in the Power Constraint element. (7.3.2.15 IEEE80211 2007)
Signed-off-by: Hong Wu <hong.wu@dspg.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hong Wu [Wed, 11 Jan 2012 18:33:39 +0000 (20:33 +0200)]
wireless: Save original maximum regulatory transmission power for the calucation of the local maximum transmit power
The local maximum transmit power is the maximum power a wireless device
allowed to transmit. If Power Constraint is presented, the local maximum
power equals to the maximum allowed power defined in regulatory domain
minus power constraint.
The maximum transmit power is maximum power a wireless device capable of
transmitting, and should be used in Power Capability element (7.3.2.16
IEEE802.11 2007).
The transmit power from a wireless device should not greater than the
local maximum transmit power.
The maximum transmit power was not calculated correctly in the current
Linux wireless/mac80211 when Power Constraint is presented.
Signed-off-by: Hong Wu <hong.wu@dspg.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nicolas Cavallari [Wed, 11 Jan 2012 15:44:50 +0000 (16:44 +0100)]
carl9170: claim to support IBSS RSN.
On carl9170, HW encryption is disabled on IBSS; the mac80211
software-based encryption is used instead. As mac80211 supports IBSS
RSN (per-STA GTK), claim its support in the carl9170 PHY.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Antonio Quartulli [Mon, 9 Jan 2012 18:43:06 +0000 (19:43 +0100)]
mac80211: In IBSS the DA field of auth frames is different from BSSID
In case of authentication frame exchange between two IBSS STAs, the
DA field must contain the destinatioin address (instead of the BSSID).
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 9 Jan 2012 12:57:36 +0000 (13:57 +0100)]
mac80211: refactor __ieee80211_get_channel_mode
Use a switch statement instead of a list of if
statements. Also include AP_VLAN in the list
and skip them since the AP interface will also
be looked at.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Mon, 9 Jan 2012 09:40:50 +0000 (10:40 +0100)]
drivers/net/wireless/mwifiex/scan.c: convert GFP_KERNEL to GFP_ATOMIC
The function is called with locks held and thus should not use GFP_KERNEL.
The semantic patch that makes this report is available
in scripts/coccinelle/locks/call_kern.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ilan Elias [Sun, 8 Jan 2012 11:43:02 +0000 (13:43 +0200)]
NFC: Increase NCI deactivate timeout
Increase NCI deactivate timeout from 5 sec to 30 sec.
NCI deactivate procedure might take a long time,
depending on the local and remote parameters.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ilan Elias [Sun, 8 Jan 2012 09:21:53 +0000 (11:21 +0200)]
NFC: Complete NCI deactivate in deactivate_ntf
If a target was active, complete the NCI deactivate request
only in deactivate_ntf. Otherwise, complete it at deactivate_rsp.
Deactivate_ntf represents the actual disconnection event (sent from
the NCI controller).
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sun, 8 Jan 2012 02:46:47 +0000 (20:46 -0600)]
rtl8192se: Update copyright dates
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sun, 8 Jan 2012 02:46:46 +0000 (20:46 -0600)]
rtl8192de: Update copyright dates
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sun, 8 Jan 2012 02:46:45 +0000 (20:46 -0600)]
rtl8192cu: Update copyright dates
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sun, 8 Jan 2012 02:46:44 +0000 (20:46 -0600)]
rtl8192ce: Update copyright dates
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sun, 8 Jan 2012 02:46:43 +0000 (20:46 -0600)]
rtl8192c_common: Update copyright dates
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sun, 8 Jan 2012 02:46:42 +0000 (20:46 -0600)]
rtlwifi: Update copyright dates
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sun, 8 Jan 2012 02:46:41 +0000 (20:46 -0600)]
rtl8192cu: Remove dead code never selected
The original driver contained some conditional code that was not selected,
but was not deleted in case it would be used later. That code can now be
removed.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sun, 8 Jan 2012 02:46:40 +0000 (20:46 -0600)]
rtlwifi: rtl8192c_common: rtl8192de: Check for allocation failures
In https://bugzilla.redhat.com/show_bug.cgi?id=771656, a kernel bug was
triggered due to a failed skb allocation that was not checked. This event
lead to an audit of all memory allocations in the complete rtlwifi family
of drivers. This patch fixes the rest.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Sat, 7 Jan 2012 15:36:21 +0000 (21:06 +0530)]
mac80211: minor cleanup
we would have bailed out if 'ifibss->fixed_channel'
is valid i.e. we had used 'fixed-freq' parameter in iw ibss
join command. this is with the state 'IEEE80211_IBSS_MLME_JOINED'
so no need to check for it
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 6 Jan 2012 21:16:33 +0000 (13:16 -0800)]
iwlwifi: update Copyright
Update Copyright to 2012
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kenny Hsu [Fri, 6 Jan 2012 21:16:32 +0000 (13:16 -0800)]
iwlwifi: add testmode cmd IWL_TM_CMD_APP2DEV_GET_FW_INFO
Add new testmode command IWL_TM_CMD_APP2DEV_GET_FW_INFO for
reporting the following information of existing loaded uCode image.
+ uCode type
+ Instruction section size
+ Data section size
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kenny Hsu [Fri, 6 Jan 2012 21:16:31 +0000 (13:16 -0800)]
iwlwifi: update error dump in testmode command sram_read
The error message will be show up by using IWL_ERR
insteads of IWl_DEBUG_INFO.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kenny Hsu [Fri, 6 Jan 2012 21:16:30 +0000 (13:16 -0800)]
iwlwifi: enhance testmode command sram_read
This patch enables SRAM read function to support entire target memory.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kenny Hsu [Fri, 6 Jan 2012 21:16:29 +0000 (13:16 -0800)]
iwlwifi: update testmode command of direct register access
In order to make sure the testcommand function of direct register
access can be performed even NIC is asleep, replace corresponding
handler iwl_read32 and iwl_write32 by using iwl_direct_read32 and
iwl_direct_write32.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 6 Jan 2012 21:16:28 +0000 (13:16 -0800)]
iwlwifi: Sanity check for sta_id
On my testing, I saw some strange behavior
[ 421.739708] iwlwifi 0000:01:00.0: ACTIVATE a non DRIVER active station id 148 addr 00:00:00:00:00:00
[ 421.739719] iwlwifi 0000:01:00.0: iwl_sta_ucode_activate Added STA id 148 addr 00:00:00:00:00:00 to uCode
not sure how it happen, but adding the sanity check to prevent memory
corruption
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 6 Jan 2012 21:16:27 +0000 (13:16 -0800)]
iwlwifi: don't process the info from uCode if does not has ownership
When enable the testmode from user space and working with uCode, driver does
not own the uCode and should not process the notifications or pkts from uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Fri, 6 Jan 2012 19:31:43 +0000 (11:31 -0800)]
rtlwifi: Simplify chip version id logging
Reduce object size a few KB too.
$ size drivers/net/wireless/rtlwifi/built-in.o*
text data bss dec hex filename
584493 55333 126800 766626 bb2a2 drivers/net/wireless/rtlwifi/built-in.o.new
586904 55333 127216 769453 bbdad drivers/net/wireless/rtlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Fri, 6 Jan 2012 19:31:42 +0000 (11:31 -0800)]
rtlwifi: Remove incorrect logging message prefixes
pr_fmt() adds them. These are unnecessary and wrong.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Thu, 5 Jan 2012 16:29:07 +0000 (08:29 -0800)]
rtlwifi: add CONFIG_RTLWIFI_DEBUG to remove all of the debug logging code
It does seem odd though to have a DBG_EMERG and not always
emit it.
What might also be useful for any embedded use is to add
CONFIG_RTLWIFI_DEBUG to conditionally remove all of the
debug logging code to reduce the largish object size.
This reduces the object size by about 1/3 (250KB)
when CONFIG_RTLWIFI_DEBUG is not set.
$ size drivers/net/wireless/rtlwifi/built-in.o*
text data bss dec hex filename
368722 55333 94224 518279 7e887 drivers/net/wireless/rtlwifi/built-in.o.new
586904 55333 127216 769453 bbdad drivers/net/wireless/rtlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Thu, 5 Jan 2012 03:40:45 +0000 (19:40 -0800)]
rtlwifi: Optimize RT_TRACE macro use of KBUILD_MODNAME for size
Moving the KBUILD_MODNAME to the format reduces the
overall object size a small amount.
$ size drivers/net/wireless/rtlwifi/built-in.o*
text data bss dec hex filename
586904 55333 127216 769453 bbdad drivers/net/wireless/rtlwifi/built-in.o.new
588901 55333 127216 771450 bc57a drivers/net/wireless/rtlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Thu, 5 Jan 2012 03:40:44 +0000 (19:40 -0800)]
rtlwifi: Remove duplicate __func__
The RT_TRACE macro already prepends it.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Thu, 5 Jan 2012 03:40:43 +0000 (19:40 -0800)]
rtlwifi: Convert RT_ASSERT macro to use ##__VA_ARGS__
Consolidate printks to avoid possible message interleaving
and reduce the object size.
Remove unnecessary RT_ASSERT parentheses.
Align arguments.
Coalesce formats.
Remove unnecessary __func__ use as the macro uses it.
$ size drivers/net/wireless/rtlwifi/built-in.o*
text data bss dec hex filename
588901 55333 127216 771450 bc57a drivers/net/wireless/rtlwifi/built-in.o.new
590002 55333 127560 772895 bcb1f drivers/net/wireless/rtlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Thu, 5 Jan 2012 03:40:42 +0000 (19:40 -0800)]
rtlwifi: Convert RTPRINT macro to use ##__VA_ARGS__
Consolidate printks to avoid possible message interleaving
and reduce the object size.
Remove unnecessary RTPRINT parentheses.
Coalesce formats.
Align arguments.
$ size drivers/net/wireless/rtlwifi/built-in.o*
text data bss dec hex filename
590002 55333 127560 772895 bcb1f drivers/net/wireless/rtlwifi/built-in.o.new
594841 55333 129680 779854 be64e drivers/net/wireless/rtlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Thu, 5 Jan 2012 03:40:41 +0000 (19:40 -0800)]
rtlwifi: Convert RT_TRACE macro to use ##__VA_ARGS__
Consolidate printks to avoid possible message interleaving
and reduce the object size.
Remove unnecessary RT_TRACE parentheses.
Miscellaneous typo and grammar fixes.
Add missing newlines to formats.
Remove duplicate KERN_DEBUG prefixes.
Coalesce formats.
Align arguments.
$ size drivers/net/wireless/rtlwifi/built-in.o*
text data bss dec hex filename
594841 55333 129680 779854 be64e drivers/net/wireless/rtlwifi/built-in.o.new
607022 55333 138720 801075 c3933 drivers/net/wireless/rtlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Thu, 5 Jan 2012 03:40:40 +0000 (19:40 -0800)]
rtlwifi: Standardize RT_PRINT_DATA macro and uses
Use a single printk(KERN_DEBUG to emit the header line
to avoid any possible output interleaving.
Remove unnecessary parentheses from the calling uses.
Standardize header arg without trailing \n or colon.
Fix a few pairwiase/pairwise typos.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Thu, 5 Jan 2012 03:40:39 +0000 (19:40 -0800)]
rtlwifi: Neaten RT_ASSERT, RT_TRACE, RTPRINT, RT_PRINT_DATA macros
Make the macros a bit more readable.
Use do {...} while (0) without terminating semicolons.
Add missing terminating semicolon to a few uses.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Tue, 3 Jan 2012 21:49:21 +0000 (22:49 +0100)]
b43: N-PHY: trivial: change save&rest order in RSSI polling
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Thu, 5 Jan 2012 00:05:30 +0000 (01:05 +0100)]
b43: N-PHY: implement RSSI calibration for rev3+
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stephen Hemminger [Wed, 4 Jan 2012 22:52:51 +0000 (14:52 -0800)]
brcm80211: make ethtool_ops const
All usage of ethtool_ops should be const; also add comma at end
of initializer list.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Tue, 3 Jan 2012 21:49:19 +0000 (22:49 +0100)]
b43: N-PHY: upload PAPD PGA gain delta table
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Tue, 3 Jan 2012 21:49:18 +0000 (22:49 +0100)]
b43: N-PHY: fix typos in RF control
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Tue, 3 Jan 2012 21:49:17 +0000 (22:49 +0100)]
b43: N-PHY: add helper for getting gain table
Also move the code to tables file.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Mon, 2 Jan 2012 18:31:22 +0000 (19:31 +0100)]
b43: N-PHY: implement TX power control setup
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Mon, 2 Jan 2012 18:31:21 +0000 (19:31 +0100)]
b43: add maskset helpers
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Mon, 2 Jan 2012 07:41:25 +0000 (08:41 +0100)]
bcma: SPROM: extract power info for cores
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Mon, 2 Jan 2012 07:41:24 +0000 (08:41 +0100)]
bcma: SPROM: add macro for easier extraction
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Mon, 2 Jan 2012 07:41:23 +0000 (08:41 +0100)]
ssb: SPROM: extract each core power info
We already extract some basic info but it's incomplete, reads info
about the first core only. Used data structure doesn't allow easy
adding of more cores.
This patch adds new struct and array for storing power info. The plan
is to: switch all extractors (including the ones using NVRAM) to new
struct, switch drivers, then deprecate and finally drop old SSB fields.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Thu, 29 Dec 2011 12:41:39 +0000 (14:41 +0200)]
mac80211: check sta_apply_parameters() return value
Bail out if sta_apply_parameters() returns an error.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Matt Carlson [Tue, 17 Jan 2012 15:27:23 +0000 (15:27 +0000)]
tg3: Fix single-vector MSI-X code
Kdump kernels leave MSI-X interrupts (as setup by the crashed kernel)
enabled. However, kdump only enables one CPU in the new environment,
thus causing tg3 to abort MSI-X setup. When the driver attempts to
enable INTA or MSI interrupt modes on a kdump kernel, interrupt
delivery fails.
This patch attempts to workaround the problem by forcing the driver
to enable a single MSI-X interrupt. In such a configuration, the
device's multivector interrupt mode must be disabled.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Pfaff [Tue, 17 Jan 2012 13:33:39 +0000 (13:33 +0000)]
openvswitch: Fix multipart datapath dumps.
The logic to split up the list of datapaths into multiple Netlink messages
was simply wrong, causing the list to be terminated after the first part.
Only about the first 50 datapaths would be dumped. This fixes the
problem.
Reported-by: Paul Ingram <paul@nicira.com>
Signed-off-by: Ben Pfaff <blp@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 17 Jan 2012 12:45:36 +0000 (12:45 +0000)]
ipv6: fix per device IP snmp counters
In commit
4ce3c183fca (snmp: 64bit ipstats_mib for all arches), I forgot
to change the /proc/net/dev_snmp6/xxx output for IP counters.
percpu array is 64bit per counter but the folding still used the 'long'
variant, and output garbage on 32bit arches.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Tue, 17 Jan 2012 10:48:43 +0000 (10:48 +0000)]
inetpeer: initialize ->redirect_genid in inet_getpeer()
kmemcheck complains that ->redirect_genid doesn't get initialized.
Presumably it should be set to zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michał Mirosław [Tue, 17 Jan 2012 10:00:40 +0000 (10:00 +0000)]
net: fix NULL-deref in WARN() in skb_gso_segment()
Bug was introduced in commit
c8f44affb7244f2ac3e703cab13d55ede27621bb.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Tue, 17 Jan 2012 07:57:56 +0000 (07:57 +0000)]
net: WARN if skb_checksum_help() is called on skb requiring segmentation
skb_checksum_help() has never done anything useful with skbs that
require segmentation. Setting skb->ip_summed = CHECKSUM_NONE makes
them invalid and provokes a later WARNing in skb_gso_segment().
Passing such an skb to skb_checksum_help() indicates a bug, so we
should warn about it immediately. Move the warning from
skb_gso_segment() into a shared function, and add gso_type and
gso_size to it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 17 Jan 2012 17:11:52 +0000 (12:11 -0500)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless
projects / platform / kernel / linux-3.10.git / log