drm/ttm: initialize the system domain with defaults v2

Instead of repeating that in each driver.

v2: keep the caching limitation for VMWGFX for now.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/382078/

drm/ingenic: ipu: Only enable clock when needed

Instead of keeping the IPU clock enabled constantly, enable and disable
it on demand, when the IPU plane is used. That way, we won't use any
extra power when the IPU is not used.

v2: Explain the reason of this patch

Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200730144830.10479-4-paul@crapouillou.net

drm/ingenic: ipu: Remove YUV422 from supported formats on JZ4725B

When configuring the IPU for packed YUV 4:2:2, depending on the scaling
ratios given by the source and destination resolutions, it is possible
to crash the IPU block, to the point where a software reset of the IP
does not fix it. This can happen anytime, in the first few frames, or
after dozens of minutes. The same crash also happens when the IPU is
fully controlled by the LCD controller (in that case no HW register is
written at any moment after startup), which points towards a hardware
bug.

Thanksfully multiplanar YUV is not affected.

Until this bug is fixed or worked around, address this issue by removing
support for YUV 4:2:2 on the IPU of the JZ4725B.

v2: Update commit message (remove the "crash beyond repair" bit)

Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200730144830.10479-3-paul@crapouillou.net

drm/ingenic: ipu: Only restart manually on older SoCs

On older SoCs, it is necessary to restart manually the IPU when a frame
is done processing. Doing so on newer SoCs (JZ4760/70) kinds of work
too, until the input or output resolutions or the framerate are too
high.

Make it work properly on newer SoCs by letting the LCD controller
trigger the IPU frame restart signal.

Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200730144830.10479-2-paul@crapouillou.net

drm/doc: device hot-unplug for userspace

Set up the expectations on how hot-unplugging a DRM device should look like to
userspace.

Written by Daniel Vetter's request and largely based on his comments in IRC and
from https://lists.freedesktop.org/archives/dri-devel/2020-May/265484.html .

A related Wayland protocol change proposal is at
https://gitlab.freedesktop.org/wayland/wayland-protocols/-/merge_requests/35

Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Cc: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Simon Ser <contact@emersion.fr>
Cc: Ben Skeggs <skeggsb@gmail.com>
Cc: Karol Herbst <kherbst@redhat.com>
Acked-by: Simon Ser <contact@emersion.fr>
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200707113805.30936-1-ppaalanen@gmail.com

drm/hisilicon: Fixed the warning: Assignment of 0/1 to bool variable

fixed the following warning:
hibmc_drm_drv.c:296:1-18:WARNING: Assignment of 0/1 to bool variable.
hibmc_drm_drv.c:301:2-19: WARNING: Assignment of 0/1 to bool variable.

v2:
using the pci_dev.msi_enabled instead of priv->msi_enabled.

v3:
just call pci_enable_msi() and pci_disable_msi(), it's no need to
set dev->pdev->msi_enabled again.

Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-By: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1595940907-17874-1-git-send-email-tiantao6@hisilicon.com

drm/ingenic: Validate mode in a .mode_valid callback

Validate modes in the drm_crtc_helper_funcs.mode_valid() callback, which
is designed for this purpose, instead of doing it in
drm_crtc_helper_funcs.atomic_check().

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200728151641.26124-3-paul@crapouillou.net

drm/ingenic: Handle errors of drm_atomic_get_plane_state

drm_atomic_get_plane_state() can return errors, so we need to handle
these.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200728151641.26124-2-paul@crapouillou.net

drm/panel: simple: Add Powertip PH800480T013 panel

Add support for Powertip PH800480T013 800x480 parallel LCD, this
one is used in the Raspberry Pi 7" touchscreen display unit.

Signed-off-by: Marek Vasut <marex@denx.de>
To: dri-devel@lists.freedesktop.org
Cc: Eric Anholt <eric@anholt.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200728121246.23304-3-marex@denx.de

dt-bindings: Add DT bindings for Powertip PH800480T013

Add DT bindings for Powertip PH800480T013 800x480 parallel LCD,
this one is used in the Raspberry Pi 7" touchscreen display unit.

Signed-off-by: Marek Vasut <marex@denx.de>
To: dri-devel@lists.freedesktop.org
Cc: Eric Anholt <eric@anholt.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200728121246.23304-2-marex@denx.de

dt-bindings: Add vendor prefix for Powertip

The Powertip Tech. Corp. is an LCD panel manufacturer.

Signed-off-by: Marek Vasut <marex@denx.de>
To: dri-devel@lists.freedesktop.org
Cc: Eric Anholt <eric@anholt.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200728121246.23304-1-marex@denx.de

drm: mxsfb: Support the alpha plane

The LCDIF in the i.MX6SX and i.MX7 have a second plane called the alpha
plane. Support it.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-23-laurent.pinchart@ideasonboard.com

drm: mxsfb: Remove unnecessary spaces after tab

This is a cosmetic change only, no code change is included.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-22-laurent.pinchart@ideasonboard.com

drm: mxsfb: Merge mxsfb_set_pixel_fmt() and mxsfb_set_bus_fmt()

The mxsfb_set_pixel_fmt() and mxsfb_set_bus_fmt() functions both deal
with format configuration, are always called in a row from
mxsfb_crtc_mode_set_nofb(), and set fields from the LCDC_CTRL register.
This requires a read-modify-update cycle in mxsfb_set_bus_fmt(). Make
this more efficient by merging them together.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-21-laurent.pinchart@ideasonboard.com

drm: mxsfb: Turn mxsfb_set_pixel_fmt() into a void function

The mxsfb_set_pixel_fmt() function returns an error when the selected
pixel format is unsupported. This can never happen, as such errors are
caught by the DRM core. Remove the error check.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-20-laurent.pinchart@ideasonboard.com

drm: mxsfb: Drop non-OF support

The mxsfb driver is only used by OF platforms. Drop non-OF support.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-19-laurent.pinchart@ideasonboard.com

drm: mxsfb: Update internal IP version number for i.MX6SX

The LCDIF present in the i.MX6SX has extra features compared to
the i.MX28. It has however lost its IP version register, so no official
version number is known. Bump the version to MXSFB_V6 following the i.MX
version, in preparation for support for the additional features.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-18-laurent.pinchart@ideasonboard.com

drm: mxsfb: Add i.MX7 and i.MX8M to the list of supported SoCs in Kconfig

Extend the Kconfig option description by listing the i.MX7 and i.MX8M
SoCs, as they are supported by the same driver. Replace the list of SoCs
in the short description with just "(e)LCDIF LCD controller" to avoid
expanding it further in the future as support for more SoCs is added.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-17-laurent.pinchart@ideasonboard.com

drm: mxsfb: Remove mxsfb_devdata unused fields

The debug0 and ipversion fields of the mxsfb_devdata structure are
unused. Remove them.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-16-laurent.pinchart@ideasonboard.com

drm: mxsfb: Enable vblank handling

Enable vblank handling when the CRTC is turned on and disable it when it
is turned off. This requires moving vblank init after the KMS pipeline
initialisation, otherwise drm_vblank_init() gets called with 0 CRTCs.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-15-laurent.pinchart@ideasonboard.com

drm: mxsfb: Don't touch AXI clock in IRQ context

The driver attempts agressive power management by enabling and disabling
the AXI clock around register accesses. This results in attempts to
enable and disable the clock in the IRQ handler, which is a no-go as
preparing or unpreparing the clock may sleep.

On the other hand, the driver enables the AXI clock when enabling the
CRTC and keeps it enabled until the CRTC is disabled. This is correct,
and renders the power management attempt pointless, as interrupts are
not supposed to occur when the CRTC is off.

The same reasoning can be applied to the CRTC .enable_vblank() and
.disable_vblank() that are not supposed to be called when the CRTC off
and thus don't require manual handling of the AXI clock. Furthermore,
vblank handling is never enabled, which results in the vblank enable and
disable handlers never being called.

To fix this, remove the manual clock handling in the IRQ, the CRTC
.enable_vblank() and .disable_vblank() handlers and the plane
.atomic_update() handler. We however need to handle the clock manually
in mxsfb_irq_disable() as is calls .disable_vblank() manually and is
used both at probe and remove time.

The clock disabling is also moved to the last step of the
mxsfb_crtc_atomic_disable() function, to prepare for enabling vblank
handling.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-14-laurent.pinchart@ideasonboard.com

drm: mxsfb: Move vblank event arm to CRTC .atomic_flush()

The vblank event is armed in the plane .atomic_update(). This works fine
as we have a single plane, and was the only option when the driver was
using the drm_simple_kms_helper helper, but will break as soon as
multiple planes are supported. Move it to CRTC .atomic_flush().

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-13-laurent.pinchart@ideasonboard.com

drm: mxsfb: Stop using DRM simple display pipeline helper

The DRM simple display pipeline helper only supports a single plane. In
order to prepare for support of the alpha plane on i.MX6SX and i.MX7,
move away from the helper. No new feature is added.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-12-laurent.pinchart@ideasonboard.com

drm: mxsfb: Rename mxsfb_crtc.c to mxsfb_kms.c

The mxsfb_crtc.c file doesn't handle just the CRTC, but also the other
KMS objects. Rename it accordingly.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-11-laurent.pinchart@ideasonboard.com

drm: mxsfb: Remove unneeded includes

A fair number of includes are not needed. Drop them, and add a couple of
required includes that were included indirectly.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-10-laurent.pinchart@ideasonboard.com

drm: mxsfb: Remove register definitions from mxsfb_crtc.c

mxsfb_crtc.c defines several macros related to register addresses and
bit, which duplicates macros from mxsfb_regs.h. Use the macros from
mxsfb_regs.h instead and remove them.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-9-laurent.pinchart@ideasonboard.com

drm: mxsfb: Use LCDC_CTRL register name explicitly

The LCDC_CTRL register is located at address 0x0000. Some of the
accesses to the register simply use the mxsfb->base address. Reference
the LCDC_CTRL register explicitly instead to clarify the code.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-8-laurent.pinchart@ideasonboard.com

drm: mxsfb: Pass mxsfb_drm_private pointer to mxsfb_reset_block()

The mxsfb_reset_block() function isn't special, pass it the
mxsfb_drm_private pointer instead of a pointer to the base address.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-7-laurent.pinchart@ideasonboard.com

drm: mxsfb: Clarify format and bus width configuration

Replace the convoluted way to set the format and bus width through
difficult to read macros with more explicit ones. Also remove the
outdated comment related to the limitations on bus width setting as it
doesn't apply anymore (the bus width can be specified through the
display_info bus format).

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-6-laurent.pinchart@ideasonboard.com

drm: mxsfb: Remove unused macros from mxsfb_regs.h

mxsfb_regs.h defines macros related to register bits. Some of them are
not used and don't clearly map to any particular register, so their
purpose isn't known. Remove them.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-5-laurent.pinchart@ideasonboard.com

drm: mxsfb: Use BIT() macro to define register bitfields

Using BIT() is preferred over manual shifts as it's more readable,
handles the 1 << 31 case properly, and avoids other mistakes as shown by
the DEBUG0_HSYNC and DEBUG0_VSYNC bits (that are currently unused). Use
it.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-4-laurent.pinchart@ideasonboard.com

drm: mxsfb: Use drm_panel_bridge

Replace the manual connector implementation based on drm_panel with the
drm_panel_bridge helper. This simplifies the mxsfb driver by removing
connector-related code, and standardizing all pipeline control
operations on bridges.

A hack is needed to get hold of the connector, as that's our only source
of bus flags and formats for now. As soon as the bridge API provides us
with that information this can be fixed.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-3-laurent.pinchart@ideasonboard.com

drm: mxsfb: Remove fbdev leftovers

Commit 8e93f1028d74 ("drm/mxsfb: Use drm_fbdev_generic_setup()")
replaced fbdev handling with drm_fbdev_generic_setup() but left
inclusion of the drm/drm_fb_cma_helper.h header. Remove it.

Fixes: 8e93f1028d74 ("drm/mxsfb: Use drm_fbdev_generic_setup()")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727020654.8231-2-laurent.pinchart@ideasonboard.com

drm/ttm: fix pipelined gutting for evictions v2

We can't pipeline that during eviction because the memory needs
to be available immediately.

v2: fix how we cleanup the BOs resources

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Tested-by: Alex Sierra <alex.sierra@amd.com>
Link: https://patchwork.freedesktop.org/patch/379039/

drm/amdgpu: Change type of module param `ppfeaturemask` to hexint

The newly added hexint helper is more convenient for bitmasks.

Before:

    $ more /sys/module/amdgpu/parameters/ppfeaturemask
    4294950911

After:

    $ more /sys/module/amdgpu/parameters/ppfeaturemask
    0xffffbfff

Cc: amd-gfx@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/374724/

moduleparams: Add hexint type parameter

For bitmasks printing values in hex is more convenient.

Prefix with `0x` to make it clear, that it’s a hex value, and pad it
out.

Using the helper for `amdgpu.ppfeaturemask`, it will look like below.

Before:

    $ more /sys/module/amdgpu/parameters/ppfeaturemask
    4294950911

After:

    $ more /sys/module/amdgpu/parameters/ppfeaturemask
    0xffffbfff

Cc: linux-kernel@vger.kernel.org
Cc: amd-gfx@lists.freedesktop.org
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/374726/

kernel/params.c: Align last argument with a tab

The second and third arguments are aligned with tabs, so do the same for
the fourth.

Cc: linux-kernel@vger.kernel.org
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/patchwork/patch/1267600/

drm/bridge: nxp-ptn3460: add drm_panel_bridge support

Prepare the bridge driver for use in a chained setup.

- Replacing direct use of drm_panel with drm_panel_bridge support.
- Make the connector creation optional

Note: the bridge panel will use the connector type from the panel.

v3:
  - Fix wrong logic in connector creation (Laurent)

v2:
  - Use panel_bridge for local variable name to align with other drivers
  - Fix that connector was created twice (Laurent)
  - Set bridge.type to DRM_MODE_CONNECTOR_LVDS.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727170320.959777-6-sam@ravnborg.org

drm/bridge: nxp-ptn3460: add get_edid bridge operation

Add the get_edid() bridge operation to prepare for
use as a chained bridge.
Add helper function that is also used by the connector.

v2:
  - Fix memory leak (Laurent)
  - Do not save a copy of edid, read it when needed

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727170320.959777-5-sam@ravnborg.org

drm/bridge: tc358767: add drm_panel_bridge support

With the bridge operations implemented the last step to prepare
this driver for a chained setup is the use of the bridge panel driver.

The bridge panel driver is only used when a port@2 is present in
the DT. So when the display driver requests a connector
support both situations:
- connector created by bridge panel driver
- connector created by this driver

And on top, support that the display driver creates the connector,
which is the preferred setup.

Note: the bridge panel will use the connector type from the panel.

v3:
  - Fix wrong logic in connector creation (Laurent)

v2:
  - Merge connector and drm_panel_bridge patches
    and fix so we do not create two connectors (Laurent)

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727170320.959777-4-sam@ravnborg.org

drm/bridge: tc358767: add get_edid bridge operation

Prepare for chained bridge with the addition of
get_edid support.

v2:
  - Fixed handling of edid storage (Laurent)

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727170320.959777-3-sam@ravnborg.org

drm/bridge: tc358767: add detect bridge operation

Prepare the bridge driver for chained operation by adding
support for the detect operation.

v3:
  - Fix code to make it readable (Laurent)

v2:
  - Do not announce detect operation if there is no hpd pin (Laurent)

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727170320.959777-2-sam@ravnborg.org

drm/bridge: megachips: make connector creation optional

Make the connector creation optional to enable usage of the
megachips-stdpxxxx-ge-b850v3-fw bridge with the DRM bridge connector
helper.

v2:
  - Set bridge.type to DRM_MODE_CONNECTOR_DisplayPort

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200726203324.3722593-14-sam@ravnborg.org

drm/bridge: megachips: add get_edid bridge operation

To prepare for a chained bridge setup add support for the
get_edid bridge operation.
There is no need for a copy of the edid - so drop
the pointer to the copy.

v2:
  - Fix so we do not leak memory (Laurent)

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200726203324.3722593-13-sam@ravnborg.org

drm/bridge: megachips: enable detect bridge operation

To prepare for use in a chained bridge setup enable the
detect operation.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200726203324.3722593-12-sam@ravnborg.org

drm/bridge: megachips: get drm_device from bridge

Fix so drm_device is read from the bridge.
This is a preparation for the connector being optional.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200726203324.3722593-11-sam@ravnborg.org

drm/bridge: megachips: add helper to create connector

Factor out connector creation to a small helper function.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200726203324.3722593-10-sam@ravnborg.org

drm/bridge: parade-ps8622: add drm_panel_bridge support

Prepare the bridge driver for use in a chained setup by
replacing direct use of drm_panel with drm_panel_bridge support.

The connecter is now either created by the panel bridge or the display
driver. So all code for connector creation in this driver is no longer
relevant and thus dropped.

The connector code had some special polling handling:
    connector.polled = DRM_CONNECTOR_POLL_HPD;
    drm_helper_hpd_irq_event(ps8622->bridge.dev);

This code was most likely added to speed up detection of the connector.
If really needed then this functionality belongs somewhere else.

Note: the bridge panel will use the connector type from the panel.

v2:
  - Fix to avoid creating connector twice (Laurent)
  - Drop all connector code - defer to bridge panel
  - Use panel_bridge for local variable to align with other drivers
  - Set bridge.type to DRM_MODE_CONNECTOR_LVDS;

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200726203324.3722593-9-sam@ravnborg.org

drm/bridge: tc358764: add drm_panel_bridge support

Prepare the tc358764 bridge driver for use in a chained setup by
replacing direct use of drm_panel with drm_panel_bridge support.

The bridge panel will use the connector type reported by the panel,
where the connector for this driver hardcodes DRM_MODE_CONNECTOR_LVDS.

The tc358764 did not add any additional info the the connector so the
connector creation is passed to the bridge panel driver.

v3:
  - Merge with patch to make connector creation optional to avoid
    creating two connectors (Laurent)
  - Pass connector creation to bridge panel, as this bridge driver
    did not add any extra info to the connector.
  - Set bridge.type to DRM_MODE_CONNECTOR_LVDS.

v2:
  - Use PTR_ERR_OR_ZERO() (kbuild test robot)

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: kbuild test robot <lkp@intel.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200726203324.3722593-5-sam@ravnborg.org

drm/bridge: tc358764: drop drm_connector_(un)register

Drop drm_connector handling that is not needed:

- drm_dev_register() in the display controller driver takes
  care of registering connectors.
  So the call to drm_connector_register() call is not needed in the bridge
  driver.

- Use of drm_connector_unregister() is only required for drivers that
  explicit have called drm_dev_register.

- The reference counting using drm_connector_put() is likewise not needed.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200726203324.3722593-4-sam@ravnborg.org

drm/panel: panel-simple: add default connector_type

All panels shall report a connector type.
panel-simple has a lot of panels with no connector_type,
and for these fall back to DPI as the default.

v2:
  - Rebased on top of validation of panel description

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200726203324.3722593-3-sam@ravnborg.org

drm/panel: panel-simple: validate panel description

Warn if we detect a panel with incomplete/wrong description.
This is inspired by a similar patch by Laurent that introduced checks
for LVDS panels - this extends the checks to the remaining type of
connectors.

This is known to warn for some of the existing panels but added
despite this as we need help from people using the panels to
add the missing info.
The checks are not complete but will catch the most common mistakes.

The checks at the same time serve as documentation for the minimum
required description for a panel.

The checks uses dev_warn() as we know this will hit. WARN() was
too noisy at the moment for anything else than LVDS.

v3:
  - %d => %u for bpc (Laurent)
v2:
  - Use dev_warn (Laurent)
  - Check for empty bus_flags

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200726203324.3722593-2-sam@ravnborg.org

drm/panel: add connector type to boe,hv070wsa-100 panel

The boe,hv070wsa-100 panel is a LVDS panel.
Fix connector type to reflect this.

With this change users of this panel do not have to specify the
connector type.

v4:
  - Add .bpc = 4 (Laurent)

v3:
  - Drop PIXDATA bus_flag, not relevant

v2:
  - Add .bus_format (Laurent)
  - Add .bus_flags

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200703192417.372164-2-sam@ravnborg.org

drm/bridge: Introduce LT9611 DSI to HDMI bridge

Lontium Lt9611 is a DSI to HDMI bridge which supports two DSI ports and
I2S port as an input and HDMI port as output

Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> # fix lt9611_bridge_mode_valid
Link: https://patchwork.freedesktop.org/patch/msgid/20200723163442.1280414-4-vkoul@kernel.org

dt-bindings: display: bridge: Add documentation for LT9611

Lontium LT9611 is a DSI to HDMI bridge which supports 2 DSI ports
and I2S port as input and one HDMI port as output

Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200723163442.1280414-3-vkoul@kernel.org

dt-bindings: vendor-prefixes: Add Lontium vendor prefix

Add prefix for Lontium Semiconductor Corporation

Acked-by: Rob Herring <robh@kernel.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200723163442.1280414-2-vkoul@kernel.org

drm/todo: Plumb drm_atomic_state all over

Add a TODO for plumbing drm_atomic_state all over to ease
the hurdles of accessing additional object states.

Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> #irc
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200717135439.5996-1-ville.syrjala@linux.intel.com

drm: pl111: Update documentation

Remove notes about migrating from the old driver which is
retired as all users are now migrated.

Update the text to reflect that we support PL110 and PL111
alike.

Drop the bullet on memory bandwidth scaling: this has been
implemented.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Russell King <linux@armlinux.org.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200720130327.92364-1-linus.walleij@linaro.org

drm/ttm: remove TTM_MEMTYPE_FLAG_MAPPABLE

Not used any more. And it is bad design to use a TTM flag
to do a check inside a driver.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/378245/

drm/amdgpu: stop using TTM_MEMTYPE_FLAG_MAPPABLE

The driver does support some not-mapable resources, but
those are already handled correctly in the switch/case
statement in the code.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/378243/

drm/radeon: stop using TTM_MEMTYPE_FLAG_MAPPABLE

The driver doesn't expose any not-mapable memory resources.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/378239/

dt-binding: display: Allow a single port node on rocktech, jh057n00900

The display has one port. Allow it in the binding.

Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200703114717.2140832-3-megous@megous.com

dt-bindings: display: Fix example in nwl-dsi.yaml

The example is now validated against rocktech,jh057n00900 schema
that was ported to yaml, and didn't validate with:

- '#address-cells', '#size-cells', 'port@0' do not match any of
  the regexes: 'pinctrl-[0-9]+'
- 'vcc-supply' is a required property
- 'iovcc-supply' is a required property
- 'reset-gpios' is a required property

Fix it.

Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200703114717.2140832-2-megous@megous.com

drm/vblank: Use spin_(un)lock_irq() in drm_crtc_queue_sequence_ioctl()

This is an ioctl callback, so we're guaranteed to have IRQs enabled when
calling this function. Use the plain _irq() variants of spin_(un)lock()
to make this more obvious.

Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200720190736.180297-6-lyude@redhat.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/vblank: Use spin_(un)lock_irq() in drm_queue_vblank_event()

This one's easy - we're already calling kzalloc(GFP_KERNEL) in this
function, so we must already be guaranteed to have IRQs enabled when
calling this. So, use the plain _irq() variants of spin_(un)lock() to
make this more obvious.

Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200720190736.180297-5-lyude@redhat.com

drm/vblank: Use spin_(un)lock_irq() in drm_legacy_vblank_post_modeset()

This function is only ever called from ioctl context, so we're
guaranteed to have interrupts enabled. Stop using the irqsave/irqrestore
variants of spin_(un)lock_irq() to make this more obvious.

Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200720190736.180297-4-lyude@redhat.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/vblank: Use spin_(un)lock_irq() in drm_crtc_vblank_on()

This is only called from:
* Atomic modesetting hooks
* Module probing routines
* Legacy modesetting hooks

All of which have IRQs enabled, so we can also get rid of
irqsave/restore here to make the IRQ context of this function more
obvious.

Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200720190736.180297-3-lyude@redhat.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/vblank: Use spin_(un)lock_irq() in drm_crtc_vblank_reset()

All of the drivers in the kernel tree only call this from one of the
following contexts:

* drm_crtc_funcs->reset
* During initial module load

Since both of these contexts are guaranteed to have interrupts enabled
beforehand, there's no need to use the irqsave/irqrestore variants of
spin_(un)lock(). So, fix this to make the irq context of this function
more obvious.

Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200720190736.180297-2-lyude@redhat.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/qxl: stop using TTM_MEMTYPE_FLAG_MAPPABLE v2

The driver doesn't expose any not-mapable memory resources.

v2: remove unused man variable as well

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/378246/

drm/nouveau: stop using TTM_MEMTYPE_FLAG_MAPPABLE

The driver doesn't expose any not-mapable memory resources.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/378244/

drm/vmwgfx: stop using TTM_MEMTYPE_FLAG_MAPPABLE

The driver doesn't expose any not-mapable memory resources.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/378241/

drm/ttm: remove TTM_MEMTYPE_FLAG_CMA

The original intention was to avoid CPU page table unmaps
when BOs move between the GTT and SYSTEM domain.

The problem is that this never correctly handled changes
in the caching attributes or backing pages.

Just drop this for now and simply unmap the CPU page
tables in all cases.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/378240/

drm/ttm: cleanup coding style and implementation.

Only functional change is to always keep io_reserved_count up to date
for debugging even when it is not used otherwise.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/378242/

drm/ttm: remove io_reserve_fastpath flag

Just use the use_io_reserve_lru flag. It doesn't make much
sense to have two flags.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/378238/

drm/ttm: cleanup io_mem interface with nouveau

Nouveau is the only user of this functionality and evicting io space
on -EAGAIN is really a misuse of the return code.

Instead switch to using -ENOSPC here which makes much more sense and
simplifies the code.

This could unbreak something as we now cleanly return EAGAIN, but the
chance for this are rather low.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/378237/

drm: remove optional dummy function from drivers using TTM

Implementing those is completely unnecessary.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Madhav Chauhan <madhav.chauhan@amd.com>
Link: https://patchwork.freedesktop.org/patch/378236/

dma-buf.rst: Document why indefinite fences are a bad idea

Comes up every few years, gets somewhat tedious to discuss, let's
write this down once and for all.

What I'm not sure about is whether the text should be more explicit in
flat out mandating the amdkfd eviction fences for long running compute
workloads or workloads where userspace fencing is allowed.

v2: Now with dot graph!

v3: Typo (Dave Airlie)

Reviewed-by: Thomas Hellstrom <thomas.hellstrom@intel.com>
Acked-by: Jason Ekstrand <jason@jlekstrand.net>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Stone <daniels@collabora.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Jesse Natalie <jenatali@microsoft.com>
Cc: Steve Pronovost <spronovo@microsoft.com>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Thomas Hellstrom <thomas.hellstrom@intel.com>
Cc: linux-media@vger.kernel.org
Cc: linaro-mm-sig@lists.linaro.org
Cc: linux-rdma@vger.kernel.org
Cc: amd-gfx@lists.freedesktop.org
Cc: intel-gfx@lists.freedesktop.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Christian König <christian.koenig@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200709123339.547390-1-daniel.vetter@ffwll.ch

dma-fence: prime lockdep annotations

Two in one go:
- it is allowed to call dma_fence_wait() while holding a
  dma_resv_lock(). This is fundamental to how eviction works with ttm,
  so required.

- it is allowed to call dma_fence_wait() from memory reclaim contexts,
  specifically from shrinker callbacks (which i915 does), and from mmu
  notifier callbacks (which amdgpu does, and which i915 sometimes also
  does, and probably always should, but that's kinda a debate). Also
  for stuff like HMM we really need to be able to do this, or things
  get real dicey.

Consequence is that any critical path necessary to get to a
dma_fence_signal for a fence must never a) call dma_resv_lock nor b)
allocate memory with GFP_KERNEL. Also by implication of
dma_resv_lock(), no userspace faulting allowed. That's some supremely
obnoxious limitations, which is why we need to sprinkle the right
annotations to all relevant paths.

The one big locking context we're leaving out here is mmu notifiers,
added in

commit 23b68395c7c78a764e8963fc15a7cfd318bf187f
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Mon Aug 26 22:14:21 2019 +0200

    mm/mmu_notifiers: add a lockdep map for invalidate_range_start/end

that one covers a lot of other callsites, and it's also allowed to
wait on dma-fences from mmu notifiers. But there's no ready-made
functions exposed to prime this, so I've left it out for now.

v2: Also track against mmu notifier context.

v3: kerneldoc to spec the cross-driver contract. Note that currently
i915 throws in a hard-coded 10s timeout on foreign fences (not sure
why that was done, but it's there), which is why that rule is worded
with SHOULD instead of MUST.

Also some of the mmu_notifier/shrinker rules might surprise SoC
drivers, I haven't fully audited them all. Which is infeasible anyway,
we'll need to run them with lockdep and dma-fence annotations and see
what goes boom.

v4: A spelling fix from Mika

v5: #ifdef for CONFIG_MMU_NOTIFIER. Reported by 0day. Unfortunately
this means lockdep enforcement is slightly inconsistent, it won't spot
GFP_NOIO and GFP_NOFS allocations in the wrong spot if
CONFIG_MMU_NOTIFIER is disabled in the kernel config. Oh well.

v5: Note that only drivers/gpu has a reasonable (or at least
historical) excuse to use dma_fence_wait() from shrinker and mmu
notifier callbacks. Everyone else should either have a better memory
manager model, or better hardware. This reflects discussions with
Jason Gunthorpe.

Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: kernel test robot <lkp@intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@intel.com> (v4)
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Thomas Hellstrom <thomas.hellstrom@intel.com>
Cc: linux-media@vger.kernel.org
Cc: linaro-mm-sig@lists.linaro.org
Cc: linux-rdma@vger.kernel.org
Cc: amd-gfx@lists.freedesktop.org
Cc: intel-gfx@lists.freedesktop.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Christian König <christian.koenig@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200707201229.472834-3-daniel.vetter@ffwll.ch

dma-fence: basic lockdep annotations

Design is similar to the lockdep annotations for workers, but with
some twists:

- We use a read-lock for the execution/worker/completion side, so that
  this explicit annotation can be more liberally sprinkled around.
  With read locks lockdep isn't going to complain if the read-side
  isn't nested the same way under all circumstances, so ABBA deadlocks
  are ok. Which they are, since this is an annotation only.

- We're using non-recursive lockdep read lock mode, since in recursive
  read lock mode lockdep does not catch read side hazards. And we
  _very_ much want read side hazards to be caught. For full details of
  this limitation see

  commit e91498589746065e3ae95d9a00b068e525eec34f
  Author: Peter Zijlstra <peterz@infradead.org>
  Date:   Wed Aug 23 13:13:11 2017 +0200

      locking/lockdep/selftests: Add mixed read-write ABBA tests

- To allow nesting of the read-side explicit annotations we explicitly
  keep track of the nesting. lock_is_held() allows us to do that.

- The wait-side annotation is a write lock, and entirely done within
  dma_fence_wait() for everyone by default.

- To be able to freely annotate helper functions I want to make it ok
  to call dma_fence_begin/end_signalling from soft/hardirq context.
  First attempt was using the hardirq locking context for the write
  side in lockdep, but this forces all normal spinlocks nested within
  dma_fence_begin/end_signalling to be spinlocks. That bollocks.

  The approach now is to simple check in_atomic(), and for these cases
  entirely rely on the might_sleep() check in dma_fence_wait(). That
  will catch any wrong nesting against spinlocks from soft/hardirq
  contexts.

The idea here is that every code path that's critical for eventually
signalling a dma_fence should be annotated with
dma_fence_begin/end_signalling. The annotation ideally starts right
after a dma_fence is published (added to a dma_resv, exposed as a
sync_file fd, attached to a drm_syncobj fd, or anything else that
makes the dma_fence visible to other kernel threads), up to and
including the dma_fence_wait(). Examples are irq handlers, the
scheduler rt threads, the tail of execbuf (after the corresponding
fences are visible), any workers that end up signalling dma_fences and
really anything else. Not annotated should be code paths that only
complete fences opportunistically as the gpu progresses, like e.g.
shrinker/eviction code.

The main class of deadlocks this is supposed to catch are:

Thread A:

mutex_lock(A);
mutex_unlock(A);

dma_fence_signal();

Thread B:

mutex_lock(A);
dma_fence_wait();
mutex_unlock(A);

Thread B is blocked on A signalling the fence, but A never gets around
to that because it cannot acquire the lock A.

Note that dma_fence_wait() is allowed to be nested within
dma_fence_begin/end_signalling sections. To allow this to happen the
read lock needs to be upgraded to a write lock, which means that any
other lock is acquired between the dma_fence_begin_signalling() call and
the call to dma_fence_wait(), and still held, this will result in an
immediate lockdep complaint. The only other option would be to not
annotate such calls, defeating the point. Therefore these annotations
cannot be sprinkled over the code entirely mindless to avoid false
positives.

Originally I hope that the cross-release lockdep extensions would
alleviate the need for explicit annotations:

https://lwn.net/Articles/709849/

But there's a few reasons why that's not an option:

- It's not happening in upstream, since it got reverted due to too
  many false positives:

commit e966eaeeb623f09975ef362c2866fae6f86844f9
Author: Ingo Molnar <mingo@kernel.org>
Date:   Tue Dec 12 12:31:16 2017 +0100

    locking/lockdep: Remove the cross-release locking checks

    This code (CONFIG_LOCKDEP_CROSSRELEASE=y and CONFIG_LOCKDEP_COMPLETIONS=y),
    while it found a number of old bugs initially, was also causing too many
    false positives that caused people to disable lockdep - which is arguably
    a worse overall outcome.

- cross-release uses the complete() call to annotate the end of
  critical sections, for dma_fence that would be dma_fence_signal().
  But we do not want all dma_fence_signal() calls to be treated as
  critical, since many are opportunistic cleanup of gpu requests. If
  these get stuck there's still the main completion interrupt and
  workers who can unblock everyone. Automatically annotating all
  dma_fence_signal() calls would hence cause false positives.

- cross-release had some educated guesses for when a critical section
  starts, like fresh syscall or fresh work callback. This would again
  cause false positives without explicit annotations, since for
  dma_fence the critical sections only starts when we publish a fence.

- Furthermore there can be cases where a thread never does a
  dma_fence_signal, but is still critical for reaching completion of
  fences. One example would be a scheduler kthread which picks up jobs
  and pushes them into hardware, where the interrupt handler or
  another completion thread calls dma_fence_signal(). But if the
  scheduler thread hangs, then all the fences hang, hence we need to
  manually annotate it. cross-release aimed to solve this by chaining
  cross-release dependencies, but the dependency from scheduler thread
  to the completion interrupt handler goes through hw where
  cross-release code can't observe it.

In short, without manual annotations and careful review of the start
and end of critical sections, cross-relese dependency tracking doesn't
work. We need explicit annotations.

v2: handle soft/hardirq ctx better against write side and dont forget
EXPORT_SYMBOL, drivers can't use this otherwise.

v3: Kerneldoc.

v4: Some spelling fixes from Mika

v5: Amend commit message to explain in detail why cross-release isn't
the solution.

v6: Pull out misplaced .rst hunk.

Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Thomas Hellstrom <thomas.hellstrom@intel.com>
Cc: linux-media@vger.kernel.org
Cc: linaro-mm-sig@lists.linaro.org
Cc: linux-rdma@vger.kernel.org
Cc: amd-gfx@lists.freedesktop.org
Cc: intel-gfx@lists.freedesktop.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Christian König <christian.koenig@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200707201229.472834-2-daniel.vetter@ffwll.ch

drm/vram-helper: stop using TTM_MEMTYPE_FLAG_MAPPABLE

The helper doesn't expose any not-mapable memory resources.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/377649/

video: fbdev: Replace HTTP links with HTTPS ones

Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.

Deterministic algorithm:
For each file:
  If not .svg:
    For each line:
      If doesn't contain `\bxmlns\b`:
        For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
  If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
            If both the HTTP and HTTPS versions
            return 200 OK and serve the same content:
              Replace HTTP with HTTPS.

Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200719203714.61745-1-grandmaster@al2klimov.de

drm: Replace HTTP links with HTTPS ones

Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.

Deterministic algorithm:
For each file:
  If not .svg:
    For each line:
      If doesn't contain `\bxmlns\b`:
        For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
  If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
            If both the HTTP and HTTPS versions
            return 200 OK and serve the same content:
              Replace HTTP with HTTPS.

Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200719171428.60470-1-grandmaster@al2klimov.de

drm/mxsfb: drop unused function parameter

flags is unused since the driver was introduced in commit 45d59d704080
("drm: Add new driver for MXSFB controller").

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716174139.16602-1-u.kleine-koenig@pengutronix.de

drm/mxsfb: Make supported modifiers explicit

In contrast to other display controllers on imx like DCSS and ipuv3
lcdif/mxsfb does not support detiling e.g. vivante tiled layouts.
Since mesa might assume otherwise make it explicit that only
DRM_FORMAT_MOD_LINEAR is supported.

Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/26877532e272c12a74c33188e2a72abafc9a2e1c.1584973664.git.agx@sigxcpu.org

drm: core: Convert device logging to drm_* functions.

Convert device logging with dev_* functions into drm_* functions.

The patch has been generated with the coccinelle script below.
The script focuses on instances of dev_* functions where the drm device
context is clearly visible in its arguments.

@@expression E1; expression list E2; @@
-dev_warn(E1->dev, E2)
+drm_warn(E1, E2)

@@expression E1; expression list E2; @@
-dev_info(E1->dev, E2)
+drm_info(E1, E2)

@@expression E1; expression list E2; @@
-dev_err(E1->dev, E2)
+drm_err(E1, E2)

@@expression E1; expression list E2; @@
-dev_info_once(E1->dev, E2)
+drm_info_once(E1, E2)

@@expression E1; expression list E2; @@
-dev_notice_once(E1->dev, E2)
+drm_notice_once(E1, E2)

@@expression E1; expression list E2; @@
-dev_warn_once(E1->dev, E2)
+drm_warn_once(E1, E2)

@@expression E1; expression list E2; @@
-dev_err_once(E1->dev, E2)
+drm_err_once(E1, E2)

@@expression E1; expression list E2; @@
-dev_err_ratelimited(E1->dev, E2)
+drm_err_ratelimited(E1, E2)

@@expression E1; expression list E2; @@
-dev_dbg(E1->dev, E2)
+drm_dbg(E1, E2)

Signed-off-by: Suraj Upadhyay <usuraj35@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200718150955.GA23103@blackclown

drm/i810: switch from 'pci_' to 'dma_' API

The wrappers in include/linux/pci-dma-compat.h should go away.

The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.
It has been compile tested.

When memory is allocated in 'i810_dma_initialize()' GFP_KERNEL can be used
because its only caller, 'i810_dma_init()', already use it and no lock is
taken in the between.

@@
@@
-    PCI_DMA_BIDIRECTIONAL
+    DMA_BIDIRECTIONAL

@@
@@
-    PCI_DMA_TODEVICE
+    DMA_TO_DEVICE

@@
@@
-    PCI_DMA_FROMDEVICE
+    DMA_FROM_DEVICE

@@
@@
-    PCI_DMA_NONE
+    DMA_NONE

@@
expression e1, e2, e3;
@@
-    pci_alloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3;
@@
-    pci_zalloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3, e4;
@@
-    pci_free_consistent(e1, e2, e3, e4)
+    dma_free_coherent(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_single(e1, e2, e3, e4)
+    dma_map_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_single(e1, e2, e3, e4)
+    dma_unmap_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4, e5;
@@
-    pci_map_page(e1, e2, e3, e4, e5)
+    dma_map_page(&e1->dev, e2, e3, e4, e5)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_page(e1, e2, e3, e4)
+    dma_unmap_page(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_sg(e1, e2, e3, e4)
+    dma_map_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_sg(e1, e2, e3, e4)
+    dma_unmap_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+    dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_device(e1, e2, e3, e4)
+    dma_sync_single_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+    dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+    dma_sync_sg_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2;
@@
-    pci_dma_mapping_error(e1, e2)
+    dma_mapping_error(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_dma_mask(e1, e2)
+    dma_set_mask(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_consistent_dma_mask(e1, e2)
+    dma_set_coherent_mask(&e1->dev, e2)

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200718072822.339064-1-christophe.jaillet@wanadoo.fr

drm/ast: Use managed MM initialization

Cleaning up ast's MM code with ast_mm_fini() resets the write-combine
flags on the VRAM I/O memory. Drop ast_mm_fini() in favor of an auto-
release callback. Releasing the device also executes the callback.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716125353.31512-7-tzimmermann@suse.de

drm/ast: Initialize DRAM type before posting GPU

Posting the GPU requires the correct DRAM type to be stored in
struct ast_private. Therefore first initialize the DRAM info and
then post the GPU. This restores the original order of instructions
in this function.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes: bad09da6deab ("drm/ast: Fixed vram size incorrect issue on POWER")
Cc: Joel Stanley <joel@jms.id.au>
Cc: Y.C. Chen <yc_chen@aspeedtech.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: "Y.C. Chen" <yc_chen@aspeedtech.com>
Cc: <stable@vger.kernel.org> # v4.11+
Link: https://patchwork.freedesktop.org/patch/msgid/20200716125353.31512-6-tzimmermann@suse.de

drm/ast: Move VRAM size detection to ast_mm.c

VRAM size detection is only relevant to the memory management. Move
the code into ast_mm.c.

While at it, rename the function to ast_get_vram_size(). The function
argument's type is now struct ast_private. The result is stored in a
local variable and not in struct ast_private any longer.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716125353.31512-5-tzimmermann@suse.de

drm/ast: Use managed VRAM-helper initialization

As a first step to managed MM code in ast, switch over VRAM MM helpers.

v2:
* updated to use drmm_vram_helper_init()

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716125353.31512-4-tzimmermann@suse.de

drm/ast: Rename ast_ttm.c to ast_mm.c

Although built upon TTM, the ast driver's VRAM MM helper does not
expose TTM to its users. Rename the related ast file to ast_mm.c.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716125353.31512-3-tzimmermann@suse.de

drm/vram-helper: Managed vram helpers

Calling drmm_vram_helper_init() sets up a managed instance of
VRAM MM. Releasing the DRM device also frees the memory manager.

The patch also updates the DRM documentation for VRAM helpers. The
tutorial now describes the new managed interface. The old interfaces
are deprecated and should not be used in new code.

v2:
* rename init function to drmm_vram_helper_init()
* return errno code from init function; caller does not
  need vram_mm anyway
* update documentation and remove docs for deprecated
  un-managed functions

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716125353.31512-2-tzimmermann@suse.de

drm/ingenic: Silence uninitialized-variable warning

Silence compiler warning about used but uninitialized 'ipu_state'
variable. In practice, the variable would never be used when
uninitialized, but the compiler cannot know that 'priv->ipu_plane' will
always be NULL if CONFIG_INGENIC_IPU is disabled.

Silence the warning by initializing the value to NULL.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200719093834.14084-1-paul@crapouillou.net

drm/ingenic: Bump driver to version 1.1

Bump version to 1.1 and set date to 2020-07-16.

v3: New patch

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716163846.174790-12-paul@crapouillou.net

drm/ingenic: Support multiple panels/bridges

Support multiple panels or bridges connected to the same DPI output of
the SoC. This setup can be found for instance on the GCW Zero, where the
same DPI output interfaces the internal 320x240 TFT panel, and the ITE
IT6610 HDMI chip.

v2: No change

v3: Allow > 80-char lines where it makes sense

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716163846.174790-11-paul@crapouillou.net

drm/ingenic: Add support for the IPU

Add support for the Image Processing Unit (IPU) found in all Ingenic
SoCs.

The IPU can upscale and downscale a source frame of arbitrary size
ranging from 4x4 to 4096x4096 on newer SoCs, with bicubic filtering
on newer SoCs, bilinear filtering on older SoCs. Nearest-neighbour can
also be obtained with proper coefficients.

Starting from the JZ4725B, the IPU supports a mode where its output is
sent directly to the LCDC, without having to be written to RAM first.
This makes it possible to use the IPU as a DRM plane on the compatible
SoCs, and have it convert and scale anything the userspace asks for to
what's available for the display.

Regarding pixel formats, older SoCs support packed YUV 4:2:2 and various
planar YUV formats. Newer SoCs introduced support for RGB.

Since the IPU is a separate hardware block, to make it work properly the
Ingenic DRM driver will now register itself as a component master in
case the IPU driver has been enabled in the config.

When enabled in the config, the CRTC will see the IPU as a second primary
plane. It cannot be enabled at the same time as the regular primary
plane. It has the same priority, which means that it will also display
below the overlay plane.

v2: - ingenic-ipu is no longer its own module. It will be built
      into the ingenic-drm module.
    - If enabled in the config, both the core driver and the IPU
      driver will register as components; otherwise the core
      driver will bypass that and call the ingenic_drm_bind()
      function directly.
    - Since both files now build into the same module, the
      symbols previously exported as GPL are not exported anymore,
      since they are only used internally.
    - Fix SPDX license header in ingenic-ipu.h
    - Avoid using 'for(;;);' loops without trailing statement(s)

v3: - Pass priv structure to IRQ handler; that way we don't hardcode
      the expectation that the IPU plane is at index #0.
    - Rework osd_changed() to account for src_* changes
    - Add multiplanar YUV 4:4:4 support
    - Commit fb addresses to HW at vblank, since addr registers are
      not shadow registers
    - Probe IPU component later so that IPU plane is last
    - Fix driver not working on IPU-less hardware
    - Use IPU driver's name as the IRQ name to avoid having two
      'ingenic-drm' in /proc/interrupts
    - Fix IPU only working for still images on JZ4725B
    - Add a bit more code comments

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716163846.174790-10-paul@crapouillou.net

drm/ingenic: Add support for OSD mode

All Ingenic SoCs starting from the JZ4725B support OSD mode.

In this mode, two separate planes can be used. They can have different
positions and sizes, and one can be overlayed on top of the other.

v2: Use fallthrough; instead of /* fall-through */

v3: - Add custom atomic_tail function to handle case where HW gives no
      VBLANK
    - Use regmap_set_bits() / regmap_clear_bits() when possible
    - Use dma_hwdesc_f{0,1} fields in priv structure instead of array
    - Use dmam_alloc_coherent() instead of dma_alloc_coherent()
    - Use more meaningful 0xf0 / 0xf1 values as DMA descriptors IDs
    - Add a bit more code comments

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716163846.174790-9-paul@crapouillou.net

drm/ingenic: Use dmam_alloc_coherent()

Use dmam_alloc_coherent() instead of dma_alloc_coherent(). Then we don't
need to register a custom cleanup handler.

v3: New patch

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716163846.174790-8-paul@crapouillou.net

drm/ingenic: Move register definitions to ingenic-drm.h

Move the register definitions to ingenic-drm.h, to keep
ingenic-drm-drv.c tidy.

v2: Fix SPDX license tag
v3: No change

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716163846.174790-7-paul@crapouillou.net

drm/ingenic: Set DMA descriptor chain address in probe

The address of the DMA descriptor never changes. It can therefore be set
in the probe function.

v2-v3: No change

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716163846.174790-6-paul@crapouillou.net