Stanislaw Gruszka [Wed, 6 Oct 2010 09:22:10 +0000 (11:22 +0200)]
mac80211: assure we also cancel deferred scan request
This is partial revert and fix for commit
85f72bc839705294b32b6c16b491c0422f0a71b3 "mac80211: only cancel
software-based scans on suspend"
When cfg80211 request the scan and mac80211 perform some management work,
we defer the scan request. We do not canceling such requests when calling
ieee80211_scan_cancel(), because of SCAN_SW_SCANNING bit check just
before the call. So fix that problem.
Another problem, which commit
85f72bc839705294b32b6c16b491c0422f0a71b3
tries to solve, is we can not cancel HW scan. Hence patch make
ieee80211_scan_cancel() ignore HW scan (see code comments). Keeping
local->mtx lock assures that the deferred scan will not become
"working" HW scan.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Wed, 6 Oct 2010 09:22:09 +0000 (11:22 +0200)]
mac80211: keep lock when calling __ieee80211_scan_completed()
We are taking local->mtx inside __ieee80211_scan_completed(), but just
before call to that function we drop the lock. Dropping/taking lock is not
good, because can lead to hard to understand race conditions.
Patch split scan_completed() code into two functions, first must be called
with local->mtx taken and second without it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Wed, 6 Oct 2010 09:22:08 +0000 (11:22 +0200)]
mac80211: reduce number of __ieee80211_scan_completed calls
Use goto instruction to call __ieee80211_scan_completed only ones in
ieee80211_scan_work. This is prepare for the next patch.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Wed, 6 Oct 2010 05:50:08 +0000 (07:50 +0200)]
b43: N-PHY: don't duplicate setting channel in shared memory
It's already set in PHY common code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Wed, 6 Oct 2010 05:50:07 +0000 (07:50 +0200)]
b43: define B43_SHM_SH_CHAN_40MHZ
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Wed, 6 Oct 2010 05:50:06 +0000 (07:50 +0200)]
b43: N-PHY: simplify channel switching
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Oct 2010 19:34:11 +0000 (21:34 +0200)]
nl80211: fix error in generic netif_running check
Yikes! The error return keeps a netdev reference
and the rdev mutex locked, fix that!
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Oct 2010 17:39:30 +0000 (19:39 +0200)]
cfg80211/mac80211: allow per-station GTKs
This adds API to allow adding per-station GTKs,
updates mac80211 to support it, and also allows
drivers to remove a key from hwaccel again when
this may be necessary due to multiple GTKs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Oct 2010 17:37:40 +0000 (19:37 +0200)]
mac80211: avoid transmitting delBA to old AP
When roaming while we have active BA session,
we can end up transmitting delBA frames to
the old AP while we're already on the new AP's
channel, which can cause warnings.
Simply avoid sending those frames, but still
tear down the internal session state, since
they are not really necessary anyway as we
will implicitly disassociate when sending the
association to the new AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Senthil Balasubramanian [Tue, 5 Oct 2010 15:06:41 +0000 (20:36 +0530)]
ath9k: Introduce a wrapper for power save disable.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Senthil Balasubramanian [Tue, 5 Oct 2010 15:06:40 +0000 (20:36 +0530)]
ath9k: remove unnecessary power save flags.
drv_config callback is called only after the ack for the nullframe
is received and so driver need not do anything special for this.
So remove NULLFUNC_COMPLETED, PS_ENABLED flags and bf_isnullfunc
flags from ath9k as mac80211 already handles them properly.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 4 Oct 2010 18:09:50 +0000 (20:09 +0200)]
ath9k_hw: merge ath9k_hw_ani_monitor_old and ath9k_hw_ani_monitor_new
After the last rounds of cleanup, these functions are now functionally
equivalent and can thus be merged.
Also get rid of some excessive (and redundant) debug messages.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 4 Oct 2010 18:09:49 +0000 (20:09 +0200)]
ath9k_hw: remove function pointer abstraction for internal ANI ops
The code gets more concise and readable when making the new ANI functions
fall back to the old ones if ANI v2 is disabled. This also makes further code
cleanup easier.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 4 Oct 2010 18:09:48 +0000 (20:09 +0200)]
ath9k_hw: remove code duplication in phy error counter handling
Split out the PHY error counter update from ath9k_hw_ani_monitor_*, reuse
it in ath9k_hw_proc_mib_event (merged from ath9k_hw_proc_mib_event_old
and ath9k_hw_proc_mib_event_new).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 4 Oct 2010 18:09:47 +0000 (20:09 +0200)]
ath9k_hw: clean up ANI state handling
ANI state is kept per channel, so instead of keeping an array of ANI states
with an arbitrary size of 255, move the ANI state into the channel struct.
Move some config settings that are not per-channel out of
the per-channel struct to save some memory.
With those changes, ath9k_ani_restart_old and ath9k_ani_restart_new can
be merged into a single function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 4 Oct 2010 18:09:46 +0000 (20:09 +0200)]
ath9k_hw: add a helper function to check for the new ANI implementation
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 5 Oct 2010 10:03:42 +0000 (12:03 +0200)]
ath9k_hw: clean up register write buffering
Throughout the code, DISABLE_REGWRITE_BUFFER is always called right after
REGWRITE_BUFFER_FLUSH. Since that's unlikely to change any time soon, that
makes keeping those ops separate rather pointless, as it only increases
code size and line number counts.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 3 Oct 2010 17:07:17 +0000 (19:07 +0200)]
ath9k_hw: merge codepaths that access the cycle counter registers
The cycle counters are used by ANI to determine the amount of time that the
radio spent not receiving or transmitting. They're also used for debugging
purposes if the baseband watchdog on AR9003 detects a lockup.
In the future, we want to use these counters to determine the medium utilization
and export this information via survey. For that, we need to make sure that
the counter is only accessed from one place, which also ensures that
wraparounds won't occur at inconvenient points in time.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 3 Oct 2010 17:07:16 +0000 (19:07 +0200)]
ath9k_hw: clean up calibration flags
The calibration actual calibration flags are only used by the per chip family
source files, so it makes more sense to define them in those files instead
of globally. That way the code has to test for less flags.
Also instead of using a separate callback for testing whether a particular
calibration type is supported, simply adjust ah->supp_cals in the calibration
init which is called right after the hardware reset, before any of the
calibrations are run.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 6 Oct 2010 20:25:52 +0000 (16:25 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6
Johannes Berg [Tue, 5 Oct 2010 19:40:33 +0000 (21:40 +0200)]
mac80211: delete AddBA response timer
We never delete the addBA response timer, which
is typically fine, but if the station it belongs
to is deleted very quickly after starting the BA
session, before the peer had a chance to reply,
the timer may fire after the station struct has
been freed already. Therefore, we need to delete
the timer in a suitable spot -- best when the
session is being stopped (which will happen even
then) in which case the delete will be a no-op
most of the time.
I've reproduced the scenario and tested the fix.
This fixes the crash reported at
http://mid.gmane.org/
4CAB6F96.6090701@candelatech.com
Cc: stable@kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 3 Oct 2010 17:07:19 +0000 (19:07 +0200)]
ath9k_hw: fix regression in ANI listen time calculation
wireless-testing
commit
37e5bf6535a4d697fb9fa6f268a8354a612cbc00
Author: Luis R. Rodriguez <lrodriguez@atheros.com>
Date: Sat Jun 12 00:33:40 2010 -0400
ath9k_hw: fix clock rate calculations for ANI
This commit accidentally broke clock rate calculation by doubling the
calculated clock rate
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 5 Oct 2010 17:50:27 +0000 (13:50 -0400)]
Merge branch 'wireless-next' of git://git./linux/kernel/git/luca/wl12xx
Luis R. Rodriguez [Fri, 1 Oct 2010 21:05:19 +0000 (17:05 -0400)]
mac80211: fix channel assumption for association done work
Be consistent and use the wk->chan instead of the
local->hw.conf.channel for the association done work.
This prevents any possible races against channel changes
while we run this work.
In the case that the race did happen we would be initializing
the bit rates for the new AP under the assumption of a wrong
channel and in the worst case, wrong band. This could lead
to trying to assuming we could use CCK frames on 5 GHz, for
example.
This patch has a fix for kernels >= v2.6.34
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Oct 2010 14:19:42 +0000 (16:19 +0200)]
nl80211: fix remain-on-channel documentation
The documentation for NL80211_CMD_REMAIN_ON_CHANNEL
isn't accurate, an interface index is required by
the command. Update it accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Tue, 5 Oct 2010 09:32:17 +0000 (11:32 +0200)]
ath9k: get correct tx gain type in ath9k_hw_4k_get_eeprom
The base_eep_header_4k structure contains information that the
device supports high power tx gain table or not. However the
ath9k_hw_4k_get_eeprom function does not return that value when
it is called with EEP_TXGAIN_TYPE. This leads to that the tx gain
initialization will use the init values from the original tx gain
table even if the device inidicates that the high power table
should be used.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Shu Hwa Shen <shensh@zcomm.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Tue, 5 Oct 2010 04:27:17 +0000 (13:27 +0900)]
ath5k: Don't wake internal queues
We should only wake up queues which mac80211 knows about (queues 0-3). We have
another internal queue ("CAB", queue number 6) which we use for power-saved
frames. When transmitted frames are processed from this queue, we have to make
sure we don't bother mac80211 with waking a queue it doesn't know about.
this fixes:
WARNING: at /home/br1/ath/wireless-testing/net/mac80211/util.c:275
__ieee80211_wake_queue+0xd6/0xe0 [mac80211]()
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Oct 2010 08:41:47 +0000 (10:41 +0200)]
mac80211: fix deadlock with multiple interfaces
The locking around ieee80211_recalc_smps is
buggy -- it cannot acquire another interface's
mutex while the iflist mutex is held because
another code path could be holding the iface
mutex and trying to acquire the iflist mutex.
But the locking is also unnecessary, we only
check "ifmgd->associated" as a bool, and don't
use the pointer (in check_mgd_smps).
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 4 Oct 2010 19:14:06 +0000 (21:14 +0200)]
nl80211: reduce dumping boilerplate
Consolidate boilerplate code needed for .dumpit
calls operating on netdevs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 4 Oct 2010 19:14:05 +0000 (21:14 +0200)]
nl80211: use generic check for netif_running
Use a new flag that requires the netdev to be
UP and use it to check instead of coding the
check into all functions that require it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 4 Oct 2010 19:36:35 +0000 (21:36 +0200)]
nl80211: use the new genetlink pre/post_doit hooks
This makes nl80211 use the new genetlink
pre_doit/post_doit hooks for locking and
checking the interface/wiphy index.
This significantly reduces the code size
and the likelihood of locking errors.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 4 Oct 2010 19:14:03 +0000 (21:14 +0200)]
genetlink: introduce pre_doit/post_doit hooks
Each family may have some amount of boilerplate
locking code that applies to most, or even all,
commands.
This allows a family to handle such things in
a more generic way, by allowing it to
a) include private flags in each operation
b) specify a pre_doit hook that is called,
before an operation's doit() callback and
may return an error directly,
c) specify a post_doit hook that can undo
locking or similar things done by pre_doit,
and finally
d) include two private pointers in each info
struct passed between all these operations
including doit(). (It's two because I'll
need two in nl80211 -- can be extended.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Mon, 4 Oct 2010 12:31:46 +0000 (14:31 +0200)]
ipw2200: check for allocation failures
If kzalloc() fails then return should return with -ENOMEM.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Mon, 4 Oct 2010 02:17:30 +0000 (11:17 +0900)]
mac80211: Add WME information element for IBSS
Enable WME QoS in IBSS mode by adding a WME information element to beacons and
probe respones and by checking for it and marking stations as WME capable if it
is present.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:34:56 +0000 (11:34 +0200)]
rt2x00: Work around hw aggregation oddity in rt2800
If a frame is not meant to be sent as AMPDU or part of it the hw might
still decide to aggregate this frame if a previous frame started an
AMPDU. However, this will limit the usefulness of the reported tx rate
since the reported rate will be the one specified in the TXWI of the
first frame and thus it is not possible to reliably caculate the
number of retrys by substracting the reported tx rate from the tx rate
in the TXWI.
To fix this issue, only report the successful rate for frames that were
not meant to be aggregated but ended up in an aggregate.
Example:
Frame A (MCS7, AMPDU=1) B (MCS7, AMPDU=1) C (MCS12, AMDPU=0, PROBE_RATE)
Although frame C shoudn't be aggregated the hw might sill put it
into an AMPDU together with A and B. If the transmission succeeds the tx
status will contain MCS7 for all three frames. In that case we should
only report MCS7 as success rate and avoid reporting MCS12-MCS8 as
failed tx attempts as this will affect the future rate control
decisions.
This oddity might strike us in other scenarious as well but the most
common "wrong" report happened for frames used to probe a different tx
rate.
This improves the rate control decisions notable.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:34:26 +0000 (11:34 +0200)]
rt2x00: Improve cooperation between rt2800pci and minstrel
In order to lower the impact of probe rates don't send a frame as AMPDU
if the rate control algorithm sets IEEE80211_TX_CTL_RATE_CTRL_PROBE.
Otherwise a whole aggregate would be send with a probe rate which might
lead to numerous retries.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:34:05 +0000 (11:34 +0200)]
rt2x00: Fix oops caused by error path in rt2x00lib_start
When rt2x00lib_enable_radio fails to enable the radio, rt2x00lib_start
will call rt2x00queue_uninitialize to uninitialize the queues. Since,
the queues are not initialized here but already in rt2x00lib_initialize
we shouldn't uninitialize the queues here. Otherwise, a consecutive call
to rt2x00lib_start will oops (see below) because it assumes the queues
are already initialized.
BUG: unable to handle kernel NULL pointer dereference at
00000010
IP: [<
f8d2d901>] :rt2800pci:rt2800pci_clear_entry+0x1/0x40
*pde =
00000000
Oops: 0000 [#1] SMP
Modules linked in: ... rt2800pci ...
Pid: 5995, comm: hostapd Not tainted (2.6.27.8 #1)
EIP: 0060:[<
f8d2d901>] EFLAGS:
00210246 CPU: 3
EIP is at rt2800pci_clear_entry+0x1/0x40 [rt2800pci]
EAX:
00000000 EBX:
f698863c ECX:
00200296 EDX:
f8d2dee0
ESI:
f6988600 EDI:
f5b6f000 EBP:
00000000 ESP:
f6d75e4c
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process hostapd (pid: 5995, ti=
f6d74000 task=
f6ce2300 task.ti=
f6d74000)
Stack:
f698863c fa00eaec 00000000 f5b6f000 00000000 f7b67000 f5b6e280 fa00c629
f5b6f000 00000000 fa00ca3d f7b67480 00000001 fa177d4c 01b6e890 f7b67000
00000000 f7b67000 00000001 00001003 00001002 c066c366 f7b67000 c0668ad0
Call Trace:
[<
fa00eaec>] rt2x00queue_init_queues+0x5c/0x90 [rt2x00lib]
[<
fa00c629>] rt2x00lib_enable_radio+0x29/0xa0 [rt2x00lib]
[<
fa00ca3d>] rt2x00lib_start+0x5d/0xd0 [rt2x00lib]
[<
fa177d4c>] ieee80211_do_open+0x21c/0x510 [mac80211]
[<
c066c366>] dev_open+0x56/0xb0
[<
c0668ad0>] dev_set_rx_mode+0x20/0x40
[<
c066a67f>] dev_change_flags+0x7f/0x190
[<
c06b1495>] devinet_ioctl+0x515/0x690
[<
c0668d24>] __dev_get_by_name+0x74/0x90
[<
c065d3f0>] sock_ioctl+0xd0/0x240
[<
c065d320>] sock_ioctl+0x0/0x240
[<
c018179b>] vfs_ioctl+0x2b/0x90
[<
c0181a5b>] do_vfs_ioctl+0x25b/0x2a0
[<
c0181af6>] sys_ioctl+0x56/0x70
[<
c0103262>] syscall_call+0x7/0xb
[<
c0700000>] add_card+0xad0/0xba0
=======================
Code: 83 78 08 0e 74 14 8b 02 8b 48 04 85 c9 0f 99 c0 0f b6 c0 c3 8d b6
00 00 00 00 8b 02 8b 40 04 85 c0 0f 99 c0 0f b6 c0 c3 66 90 53 <8b>
48 10 8b 58 08 8b 40 04 83 78 08 0e 74 15 8b 11 83 c2 04 8b
EIP: [<
f8d2d901>] rt2800pci_clear_entry+0x1/0x40 [rt2800pci] SS:ESP 0068:
f6d75e4c
---[ end trace
cff9a5c094bb8837 ]---
Reported-by: Joshua Smith <jesmith@kaon.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:33:42 +0000 (11:33 +0200)]
rt2x00: Update comment about the AMPDU flag in the TXWI
During testing with AMPDUs it turned out that the rt2800 hw will aggregate
consecutive frames with the same RA and TID when the first frame in a
possible aggregate has set AMPDU=1 in the TXWI. If a following frame has
set AMPDU=0 in its TXWI it might sill end up in the aggregate of the
previous frame. Update the comment accordingly.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:33:17 +0000 (11:33 +0200)]
rt2x00: Enable rx aggregation in rt2800
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 2 Oct 2010 09:32:43 +0000 (11:32 +0200)]
rt2x00: Improve TX status entry validation
The TX_STA_FIFO contains some information for identifying
a outgoing frame, however matching by WCID and ACK status is
not sufficient to 100% identify the macthing queue_entry structure
(containing the SKB buffer) which belongs to the status report.
Within TX_STA_FIFO we have a 4-bit field named PACKETID, which is
currently used to encode the queue id. The queue ID is however
limited to values from 0 to 3, which means 2 bits are sufficient
to encode the value. With the remaining 2 bits we can encode a
partial queue_entry index number. The value of PACKETID is not
allowed to become 0, with the queue ID ranging from 0 to 3, at least
one of the bits for the entry identification must be 1.
That leaves us with 3 possible values we can still encode in the
bits. Altough this doesn't allow 100% accurate matching of the
TX_STA_FIFO queue to a queue_entry structure, it at least improves
the accuracy. This allows us to better detect if we have missed the
TX_STA_FIFO report, which in turn reduces the number of watchdog
warnings regarding the TX status timeout.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:32:16 +0000 (11:32 +0200)]
rt2x00: correctly set max_report_rates in rt61pci and rt2800
rt61pci and rt2800 devices can use up to 7 different rates per tx frame.
However, the device uses a global fallback table. Hence, the rc
algortihm cannot specify multiple rates to try but the device is able to
report multiple rates (based on the retry table). Specify that behavior
by correctly setting max_report_rates and max_rates.
This makes rt2x00 and minstrel play nicer together.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:31:55 +0000 (11:31 +0200)]
mac80211: distinct between max rates and the number of rates the hw can report
Some drivers cannot handle multiple retry rates specified by the rc
algorithm but instead use their own retry table (for example rt2800).
However, if such a device registers itself with a max_rates value of 1
the rc algorithm cannot make use of the extended information the device
can provide about retried rates. On the other hand, if a device
registers itself with a max_rates value > 1 the rc algorithm assumes
that the device can handle multi rate retries.
Fix this issue by introducing another hw parameter max_report_rates that
can be set to a different value then max_rates to indicate if a device
is capable of reporting more rates then specified in max_rates.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:31:33 +0000 (11:31 +0200)]
rt2x00: Don't enable broad- and multicast buffering on USB devices
Since rt2x00 USB devices have no chance to know when a beacon was sent
out in AP mode currently all broad- and multicast traffic is buffered in
mac80211 but never sent out at all.
Unfortunately we have no chance in sending the traffic out after a
DTIM beacon due to hw limitations. Hence, instead of never sending the
buffered traffic out better send it out immediately.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Reported-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:31:05 +0000 (11:31 +0200)]
rt2x00: add field definitions for the TBTT_SYNC_CFG register
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:30:42 +0000 (11:30 +0200)]
rt2x00: Add register definition for busy time on secondary channel
Add the register definition CH_BUSY_STA_SEC for reading the busy time
on the secondary channel in HT40 mode. Also update the comments about
channel busy/idle time registers to express the used unit.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 2 Oct 2010 09:30:19 +0000 (11:30 +0200)]
rt2x00: Add rt73usb device ID
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:29:59 +0000 (11:29 +0200)]
rt2x00: Allow tx duplication for legacy rates in HT40 mode
Make use of the IEEE80211_TX_RC_DUP_DATA flag to duplicate a
transmission with legacy rates to both 20Mhz channels if set.
Also update the related comment in rt2800.h to describe the
behavior of the BW_40 flag for legacy rates.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:29:30 +0000 (11:29 +0200)]
rt2x00: Fix race between dma mapping and clearing rx entries in rt2800pci
During rx, rt2x00lib calls rt2800pci_fill_rxdone to read the RX
descriptor. At that time the skb is already dma unmapped but no new skb
was dma mapped for this entry again. However, rt2800pci_fill_rxdone also
moves the hw rx queue index, marking this entry to be available for
reuse. Since no new skb was dma mapped and also the previous skb was
unmapped this might lead to strange hw behavior.
To fix this issue move the hw rx queue index increment to
rt2800pci_clear_entry where a new skb was already dma mapped and can be
safely used by the hw.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:29:08 +0000 (11:29 +0200)]
rt2x00: Don't initialize MM40 HT protection to RTS/CTS on PCI devices
Since HT protection is now configurable via mac80211 we don't need this
special case for PCI devices anymore. The HT protection config will be
overwritten as soon as mac80211 sends us a HT operation mode. Hence,
bring the HT MM40 protection config in sync with the other HT protection
registers and initialize it to no protection.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:28:34 +0000 (11:28 +0200)]
rt2x00: Implement HT protection for rt2800
Update the HT operation mode when mac80211 sends it to us and set
the different HT protection modes and rates accordingly. For now
only use CTS-to-self with OFDM 24M or CCK 11M when protection is
required.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:28:02 +0000 (11:28 +0200)]
rt2x00: Fix SM PS check
Fix a check for dynamic SM PS mode in the STAs HT caps. Since a
value of 3 means "SM PS disabled" the previous check assumed in
that case that "dynamic SM PS" was enabled and as such prefixed
every MCS>7 frame with a unnecessary RTS/CTS exchange. Also,
the bit shift was done in the wrong direction.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:27:35 +0000 (11:27 +0200)]
rt2x00: rework tx status handling in rt2800pci
This patch changes the way tx status reports are handled by rt2800pci.
Previously rt2800pci would sometimes lose tx status reports as the
TX_STA_FIFO register is a fifo of 16 entries that can overflow in case
we don't read it often/fast enough. Since interrupts are disabled in the
device during the execution of the interrupt thread it happend sometimes
under high network and CPU load that processing took too long and a few
tx status reports were dropped by the hw.
To fix this issue the TX_STA_FIFO register is read directly in the
interrupt handler and stored in a kfifo which is large enough to hold
all status reports of all used tx queues.
To process the status reports a new tasklet txstatus_tasklet is used.
Using the already used interrupt thread is not possible since we don't
want to disable the TX_FIFO_STATUS interrupt while processing them and
it is not possible to schedule the interrupt thread multiple times for
execution. A tasklet instead can be scheduled multiple times which
allows to leave the TX_FIFO_STATUS interrupt enabled while a previously
scheduled tasklet is still executing.
In short: All other interrupts are handled in the interrupt thread as
before. Only the TX_FIFO_STATUS interrupt is partly handled in the
interrupt handler and finished in the according tasklet.
One drawback of this patch is that it duplicates some code from
rt2800lib. However, that can be cleaned up in the future once the
rt2800usb and rt2800pci tx status handling converge more.
Using this patch on a Ralink RT3052 embedded board gives me a reliable
wireless connection even under high CPU and network load. I've
transferred several gigabytes without any queue lockups.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:27:03 +0000 (11:27 +0200)]
rt2x00: Split out parts of the rt2800_txdone function for easier reuse
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:26:17 +0000 (11:26 +0200)]
rt2x00: Don't overwrite beacon buffers in pairwise key setup
rt2800 devices use parts of the pariwise key table to store the beacon
frames for beacon 6 and 7. To not overwrite the beacon frame buffers
limit the number of entries we store in the pairwise key table to 222.
Also add some descriptive comments about this shared memory usage.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christian Lamparter [Fri, 1 Oct 2010 20:01:24 +0000 (22:01 +0200)]
p54usb: add five more USBIDs
Source:
http://www.wikidevi.com/wiki/Intersil/p54/usb/windows
Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Greear [Fri, 1 Oct 2010 19:26:30 +0000 (12:26 -0700)]
ath9k: Report total tx/rx bytes and packets in debugfs.
Includes pkts/bytes that may have had errors, and includes
wireless headers when counting bytes.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Greear [Fri, 1 Oct 2010 17:54:04 +0000 (10:54 -0700)]
ath5k: Print rx/tx bytes in debugfs
This adds counters for tx and rx bytes, including any
errored packets as well as all wireless headers.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bill Jordan [Fri, 1 Oct 2010 15:20:41 +0000 (11:20 -0400)]
mac80211: fix for WDS interfaces
Initialize the rate table for WDS interfaces, and
add cases to allow WDS packets to pass the xmit and receive
tests.
Signed-off-by: Bill Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bill Jordan [Fri, 1 Oct 2010 17:54:28 +0000 (13:54 -0400)]
cfg80211: patches to allow setting the WDS peer
Added a nl interface to set the peer bssid of a WDS interface.
Signed-off-by: Bill Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bill Jordan [Fri, 1 Oct 2010 15:20:39 +0000 (11:20 -0400)]
ath9k: add WDS interfaces to ath9k
Enable WDS for the ath9k driver.
Signed-off-by: Bill Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 1 Oct 2010 13:02:31 +0000 (16:02 +0300)]
mac80211: Add validity check for beacon_crc value
On association to an AP, after receiving beacons, the beacon_crc value is set.
The beacon_crc value is not reset in disassociation, but the BSS data may be
expired at a later point. When associating again, it's possible that a
beacon for the AP is not received, resulting in the beacon_ies to remain NULL.
After association, further beacons will not update the beacon data, as the
crc value of the beacon has not changed, and the beacon_crc still holds a
value matching the beacon. The beacon_ies will remain forever null.
One of the results of this is that WLAN power save cannot be entered, the STA
will remain foreven in active mode.
Fix this by adding a validation flag for the beacon_crc, which is cleared on
association.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Fri, 1 Oct 2010 12:05:27 +0000 (14:05 +0200)]
mac80211: perform scan cancel in hw reset work
Move ieee80211_scan_cancel() and all other related code to
ieee80211_restart_work() as ieee80211_restart_hw() is intended to be
callable from any context.
Fix a bug that RTNL lock is not taken during ieee80211_cancel_scan().
Take local->mtx before WARN(test_bit(SCAN_HW_SCANNING, &local->scanning)
to prevent the race condition with __ieee80211_start_scan() described
here: http://marc.info/?l=linux-wireless&m=
128516716810537&w=2
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Fri, 1 Oct 2010 09:55:05 +0000 (15:25 +0530)]
ath9k : Fix for displaying the channel number
In the ath9k debugging feature 'wiphy' the current channel used by the
station is incorrectly displayed.This is because the channels available
are sequentially mapped from numbers 0 to 37.This mapping cannot be
changed as the channel number is also used as an array index
This fix solves the above problem by calculating the channel
number from center frequency.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 30 Sep 2010 23:46:13 +0000 (01:46 +0200)]
ath9k_hw: remove some useless calibration data
The percal struct and bitmask for the initial DC calibration are not
used anywhere, so they can be removed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 30 Sep 2010 23:06:53 +0000 (01:06 +0200)]
ath9k: fix channel flag / regd issues with multiple cards
Since the regulatory code touches the channel array, it needs to be
copied for each device instance. That way the original channel array
can also be made const.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org [all]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 30 Sep 2010 20:17:43 +0000 (22:17 +0200)]
cfg80211: fix locking
Add missing unlocking of the wiphy in set_channel,
and don't try to unlock a non-existing wiphy in
set_cqm.
Cc: stable@kernel.org [2.6.35+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Greear [Thu, 30 Sep 2010 19:22:58 +0000 (12:22 -0700)]
ath5k: Allow ath5k to support virtual STA and AP interfaces.
Support up to 4 virtual APs and as many virtual STA interfaces
as desired.
This patch is ported forward from a patch that Patrick McHardy
did for me against 2.6.31.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 30 Sep 2010 19:21:25 +0000 (21:21 +0200)]
cfg80211: remove spurious __KERNEL__ ifdef
The net/cfg80211.h header file isn't exported to
userspace, so there's no need for any kind of
__KERNEL__ protection in it. If it was exported,
everything else in it would need protection as
well, not just the logging stuff ...
Cc:Joe Perches <joe@perches.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 30 Sep 2010 19:06:09 +0000 (21:06 +0200)]
cfg80211/mac80211: allow management frame TX in AP mode
Enable management frame transmission and subscribing
to management frames through nl80211 in both cfg80211
and mac80211. Also update a few places that I forgot
to update for P2P-client mode previously, and fix a
small bug with non-action frames in this API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Thu, 30 Sep 2010 14:27:35 +0000 (16:27 +0200)]
iwlwifi: change WARN_ON to IWL_WARN in iwl_mac_add_interface
We can start restarting firmware or RF kill switch can be turned on
during call to iwl_mac_add_interface(). That are normal working
conditions, so do not print call trace, just print simple message
instead.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Hutchings [Thu, 30 Sep 2010 01:44:56 +0000 (02:44 +0100)]
ar9170: Remove MODULE_FIRMWARE references to two-stage firmware
The combined firmware ar9170.fw is preferred and supports all devices.
References to the older two-stage firmware are unnecessary.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 29 Sep 2010 17:12:06 +0000 (19:12 +0200)]
ath9k: return survey data for all channels instead of just the current one
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 29 Sep 2010 15:15:30 +0000 (17:15 +0200)]
nl80211: allow drivers to indicate whether the survey data channel is in use
Some user space applications only want to display survey data for
the operating channel, however there is no API to get that yet.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 29 Sep 2010 15:15:29 +0000 (17:15 +0200)]
ath9k: remove the noise floor value in the ani struct
common->ani.noise_floor is now only used for a similar redundant debug
message similar to the one that was removed from ath9k_htc in an earlier
patch. Remove it from ath9k as well now.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 29 Sep 2010 15:15:28 +0000 (17:15 +0200)]
ath9k: do not return default noise floor values via survey
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 29 Sep 2010 15:15:27 +0000 (17:15 +0200)]
ath9k_hw: keep calibrated noise floor values per channel
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 29 Sep 2010 15:15:26 +0000 (17:15 +0200)]
ath9k_htc: remove use of common->ani.noise_floor
It is unused aside from a single redundant debug message
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christian Lamparter [Tue, 28 Sep 2010 21:00:59 +0000 (23:00 +0200)]
carl9170: support firmware-based rx filter
The hardware rx-filter was essentially disabled, because
of a serve, yet unidentifiable problem with iwlagn.
Due to these circumstances the driver and mac80211 were
left with the job of filtering.
This is very unfortunate and has proven to be expensive
in terms of latency, memory and load.
Therefore the new 1.8.8.3 firmware introduces a flexible
filtering infrastructure which allows the driver to
offload some of the checks (FCS & PLCP crc check,
RA match, control frame filter, etc...) whenever possible.
Note:
This patch also includes all changes to the
shared headers files since the inclusion.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christian Lamparter [Sat, 2 Oct 2010 11:17:07 +0000 (13:17 +0200)]
mac80211: fix rx monitor filter refcounters
This patch fixes an refcounting bug. Previously it
was possible to corrupt the per-device recv. filter
and monitor management counters when:
iw dev wlanX set monitor [new flags]
was issued on an active monitor interface.
Acked-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Greear [Mon, 27 Sep 2010 16:07:26 +0000 (09:07 -0700)]
wireless: Use first phyX name available when registering phy devices.
Choose first available phyX name when creating phy devices. This
means that reloading a wifi driver will not cause a change in the
name of it's phy device.
Also, allow users to rename a phy to any un-used name, including
phy%d.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 5 Oct 2010 15:14:58 +0000 (11:14 -0400)]
Merge branch 'wireless-next-2.6' of git://git./linux/kernel/git/iwlwifi/iwlwifi-2.6
ext Anand Gadiyar [Fri, 1 Oct 2010 20:33:26 +0000 (22:33 +0200)]
omap: zoom2/3: fix build caused by wl1271 support
Patch "omap: zoom: add mmc3/wl1271 device support" in the
wireless tree still uses .wires in struct omap2_hsmmc_info.
.wires has now been replaced with .caps in patch "omap: mmc:
extended to pass host capabilities from board file" in the
OMAP tree.
This causes linux-next as of
20101001 build to break as
below. Fix this.
CC arch/arm/mach-omap2/board-zoom-peripherals.o
arch/arm/mach-omap2/board-zoom-peripherals.c:217: error: unknown field 'wires' specified in initializer
make[1]: *** [arch/arm/mach-omap2/board-zoom-peripherals.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Luciano Coelho [Tue, 5 Oct 2010 11:58:49 +0000 (14:58 +0300)]
wl1271: remove deprecated __attribute__ ((packed))
One __attribute__ ((packed)) has been accidentally introduced in commit
be86cbea1e9c3a4dd8faedcfa327495d09fe3531. This patch changes it to __packed.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Juuso Oikarinen [Tue, 5 Oct 2010 11:11:56 +0000 (13:11 +0200)]
wl1271: Add extended radio parameter initialization
Currently a command to initialize extended radio parameter tables in the
hardware is missing.
Add the initialization
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Juuso Oikarinen [Thu, 30 Sep 2010 08:43:27 +0000 (10:43 +0200)]
wl1271: Indicate disconnection on hardware failure
In the event of a hardware failure, reconfiguring a live connection back
with the wl1271 chip does not work as expected. The chip has management
features which require setting up the association from scratch to work
correctly. To ensure this is done every time, in managed mode, when associated,
indicate connection loss to the mac80211 before asking to reconfigure the
hardware.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Tested-by: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Juuso Oikarinen [Thu, 30 Sep 2010 08:43:28 +0000 (10:43 +0200)]
wl1271: Move work-init calls to hw allocation
Due to legacy reason, dating back to when the wl1251 and wl1271 still were
a unified driver, some work-structures are initialized on hardware startup.
The hardware recovery code creates a scenario in which it is possible for a
workstruct to be re-initialized while the work-function itself is running,
which causes a kernel WARNing and a subsequent reboot.
To remedy this, move the work initialization calls to the hw allocation,
which is the logically correct place for them anyway.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Tested-by: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Ido Yariv [Thu, 30 Sep 2010 11:28:28 +0000 (13:28 +0200)]
wl1271: Support firmware TX packet aggregation
Instead of sending one packet at a time to the firmware, try to
send all available packets at once.
This optimization decreases the number of transactions, which saves
CPU cycles and increases network throughput.
Signed-off-by: Ido Yariv <ido@wizery.com>
Tested-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Ido Yariv [Thu, 30 Sep 2010 11:28:27 +0000 (13:28 +0200)]
wl1271: Support firmware RX packet aggregation
Instead of retrieving one packet at a time from the firmware, try to
retrieve all available packets at once.
This optimization decreases the number of transactions, which saves
CPU cycles and increases network throughput.
Signed-off-by: Ido Yariv <ido@wizery.com>
Tested-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Ido Yariv [Thu, 30 Sep 2010 11:28:26 +0000 (13:28 +0200)]
wl1271: Handle large SPI transfers
The HW supports up to 4095 bytes transfers via SPI. The SPI read & write
operations do not handle larger transfers, causing the HW to stall in such
cases.
Fix this by fragmenting large transfers into smaller chunks, and
transferring each one separately.
Signed-off-by: Ido Yariv <ido@wizery.com>
Tested-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Ohad Ben-Cohen [Tue, 28 Sep 2010 18:20:28 +0000 (20:20 +0200)]
wl12xx: fix non-wl12xx build scenarios
Support building wl1271-equipped boards without building the
wl1271 driver itself, e.g.:
CONFIG_MACH_OMAP_ZOOM3=y
CONFIG_WL12XX is not set
Reported-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Wey-Yi Guy [Wed, 29 Sep 2010 00:43:10 +0000 (17:43 -0700)]
iwlagn: API v5 for 6050 series device
For 6050 series device, change the supported API version
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Shanyu Zhao [Wed, 15 Sep 2010 01:13:31 +0000 (18:13 -0700)]
iwlwifi: send DC calib config to runtime ucode
Since uCode is responsible for doing DC calibration, there's no need
to let init uCode to do initial DC calibration then send results
back to driver, then driver sends the results to runtime uCode.
Driver can simply tell runtime uCode to do DC calibration.
Actually, this patch does not disable DC calib for init uCode. It just
prevent driver from saving and sending the DC calib results (from init
ucode) to runtime uCode. The driver still uses 0xffffffff in
CALIB_CFG_CMD for init ucode.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Shanyu Zhao [Tue, 14 Sep 2010 23:23:42 +0000 (16:23 -0700)]
iwlagn: set CSR register for 6050g2 devices
For 6050g2 devices driver needs to set a special bit to CSR register
so that uCode can do things correctly in calibration routines.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Shanyu Zhao [Tue, 14 Sep 2010 23:23:32 +0000 (16:23 -0700)]
iwlwifi: add iwl_nic_ops structure to iwl_ops
iwlwifi driver supports multiple devices. Since some device needs
special configuration we create a new iwl_nic_ops structure which is
configurable per device. Currently there is only one function pointer
inside this structure: additional_nic_config().
The iwl_nic_ops structure is added to the top level in struct iwl_ops,
making it easier to change per device. Duplication of the iwl_lib_ops
structure is no longer needed.
With this new ops the previous function pointer set_calib_version is
no longer needed since it is just a per device nic configuration.
As part of the code restructuring, a bug is addressed. Indication of
calib version to uCode is only needed for 6050 devices, however,
current implementation set calib version for all 6000 devices for
which DC calib is needed. To fix this, create iwl6050_ops for 6050
devices and only populate iwl_nic_ops in this structure.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Jay Sternberg [Tue, 14 Sep 2010 22:21:20 +0000 (15:21 -0700)]
iwlwifi: define 100 devices
add new structures and defines need to identify 100 devices.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
John W. Linville [Tue, 28 Sep 2010 20:01:47 +0000 (16:01 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6
Conflicts:
drivers/net/wireless/iwlwifi/iwl-agn-lib.c
drivers/net/wireless/iwlwifi/iwl3945-base.c
Juuso Oikarinen [Tue, 28 Sep 2010 11:39:32 +0000 (14:39 +0300)]
mac80211: Fix WMM driver queue configuration
The WMM parameter configuration function (ieee80211_sta_wmm_params) only
configures the WMM parameters to the driver is the wmm_last_param_set
counter value is changed by the AP.
The wmm_last_param_set is initialized to -1 on association in order to ensure
the configuration is made to the driver at least once on association, but
currently this initialization is done *after* the WMM parameter configuration
function was called.
This leads to unreliability in the driver getting properly configured on first
association (depending on what counter value the AP happens to use.) When
disassociating (the wmm default parameters are configured to the driver) and
then reassociating, due to the above the WMM configuration is not set to the
driver at all.
On drivers without beacon filtering the problem is corrected by later beacons,
but on drivers with beacon filtering the WMM will remain permanently incorrectly
configured.
Fix this by moving the initialization of wmm_last_param_set to -1 before
ieee80211_sta_wmm_params is called on association.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 28 Sep 2010 10:53:14 +0000 (12:53 +0200)]
cfg80211: always set IBSS basic rates
IBSS started from wireless extensions is currently
missing basic rate configuration, fix this by moving
the code to generate the default to the common code
that gets invoked for both nl80211 and wext.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christian Lamparter [Mon, 27 Sep 2010 23:53:42 +0000 (01:53 +0200)]
carl9170: interrupt urbs must not set URB_ZERO_PACKET
This patch fixes a bug in the driver which was
exposed by CONFIG_USB_DEBUG:
"usb 1-1.6.3: BOGUS urb flags, 40 --> 0"
The transfer flag "URB_ZERO_PACKET" is only valid
for bulk urbs.
Reported-by: André Erdmann
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Mon, 27 Sep 2010 04:02:40 +0000 (13:02 +0900)]
ath5k: Fix bitmasks and typos for PCU Diagnostic register
As reported by Ryan Niemi, some bitmasks in the register definition for the PCU
Diagnostic register (DIAG_SW) were missing a zero at the end. While at it fix
some typos and add more comments.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>