Marek Vasut [Tue, 4 Nov 2014 03:08:18 +0000 (04:08 +0100)]
usb: s3c-otg: Encapsulate PHY control
Encapsulate the Samsung PHY control and its register accesses
into the otg_phy_init() and otg_phy_off() functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Marek Vasut [Tue, 4 Nov 2014 02:43:47 +0000 (03:43 +0100)]
usb: s3c-otg: Remove useless include
Remove the useless inclusion of arch/arm/gpio.h , which is completely
bogus in this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tom Rini [Wed, 5 Nov 2014 18:11:18 +0000 (13:11 -0500)]
Merge branch 'rmobile' of git://denx.de/git/u-boot-sh
Tom Rini [Wed, 5 Nov 2014 17:48:09 +0000 (12:48 -0500)]
Merge branch 'master' of git://denx.de/git/u-boot-imx
Nikita Kiryanov [Wed, 29 Oct 2014 15:56:22 +0000 (17:56 +0200)]
arm: mx6: cm_fx6: detect 1GB DRAM correctly on solo
The 1GB DRAM configuration on mx6 solo uses 2 chip selects, but
the code tests 1GB DRAM configuration as if it is all present on one
chip select, and thus cannot see the full range of available memory.
Refactor the check to detect 1GB DRAM correctly.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Nikita Kiryanov [Wed, 29 Oct 2014 15:56:21 +0000 (17:56 +0200)]
arm: mx6: cm_fx6: change issd gpio order
Change the order in which GPIOs are toggled in SATA init sequence to
accomodate both SanDisk and Phison SSDs.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Tom Rini [Wed, 5 Nov 2014 12:23:32 +0000 (07:23 -0500)]
Merge git://www.denx.de/git/u-boot-sunxi
Tom Rini [Wed, 5 Nov 2014 12:12:16 +0000 (07:12 -0500)]
Merge git://www.denx.de/git/u-boot-ppc4xx
Hans de Goede [Fri, 31 Oct 2014 16:04:52 +0000 (17:04 +0100)]
dm: sunxi: Request USB vbus gpio
This is necessary for the device-model enabled builds to work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Hans de Goede [Fri, 31 Oct 2014 15:55:02 +0000 (16:55 +0100)]
dm: sunxi: Request card detect gpio
This is necessary for the device-model enabled builds to work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 31 Oct 2014 02:25:50 +0000 (20:25 -0600)]
dm: sunxi: Add support for serial using driver model
Add a driver for the designware serial UART used on sunxi. This just
redirects to the normal ns16550 driver.
Add a stdout-path to the device tree so that the correct UART is chosen.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Simon Glass [Fri, 31 Oct 2014 02:25:49 +0000 (20:25 -0600)]
dm: sunxi: Modify the GPIO driver to support driver model
This adds driver model support to the sunxi GPIO driver, using the device
tree to trigger binding of the driver. The driver will still operate
without driver model too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Simon Glass [Fri, 31 Oct 2014 02:25:48 +0000 (20:25 -0600)]
dm: sunxi: Make sure that GPIOs are requested
The scsi_init() function uses a GPIO so should request it. There is no
way to return an error here, and the request may be made multiple times,
so just ignore errors for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Simon Glass [Fri, 31 Oct 2014 02:25:47 +0000 (20:25 -0600)]
dm: sunxi: Add pinmux functions which take a bank parameter
With driver model we will have access to a bank pointer, so we want to
use it rather than converting back to a number, and then back to a
bank pointer. Add functions to provide this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Simon Glass [Fri, 31 Oct 2014 02:25:46 +0000 (20:25 -0600)]
dm: sunxi: Add a new config for an FDT-based pcDuino3
For now we won't want to mess with the existing configurations. Create a
new one which will enable device tree and driver model. Note that this
brings the device tree binary into u-boot-sunxi-with-spl.bin.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Simon Glass [Fri, 31 Oct 2014 02:25:45 +0000 (20:25 -0600)]
dm: sunxi: dts: Add sun7i device tree files
These are from Linux 3.17-rc7 (commit
fe82dcec). U-Boot only uses a small
portion of these, but we may as well have something to look forward to.
The total compiled size is about 25KB.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Ian Campbell [Fri, 24 Oct 2014 20:20:50 +0000 (21:20 +0100)]
sunxi: kconfig: Add %_felconfig rule to enable FEL build of sunxi platforms.
$ make BOARD_felconfig
is more convenient than
$ make BOARD_defconfig
$ echo CONFIG_SPL_FEL=y >> .config
$ echo CONFIG_SPL_FEL=y >> spl/.config
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Ian Campbell [Fri, 24 Oct 2014 20:20:49 +0000 (21:20 +0100)]
sunxi: kconfig: Introduce CONFIG_TARGET_<BOARD>
This was done automatically with the following bits of scripting.
The Kconfig choice content was generated with this script snippet:
for i in $(git grep -l CONFIG_ARCH_SUNXI configs/*) ; do
TARGET=$(sed -n -e 's/CONFIG_SYS_EXTRA_OPTIONS="\([^,"]\+\).*/\1/p' $i);
MACH=$(sed -n -e 's/.*CONFIG_\(MACH_SUN.I\)=./\1/p' $i)
echo "config TARGET_$TARGET"
echo " bool \"$TARGET\""
echo " depends on $MACH"
echo
done
defconfigs were updated with a sed script (t):
# Extract board from first entry of CONFIG_SYS_EXTRA_OPTIONS,
/^CONFIG_SYS_EXTRA_OPTIONS/ {
s/^\(CONFIG_SYS_EXTRA_OPTIONS="\)\([^,"]\+\),\?\(.*\)/\1\3\nCONFIG_TARGET_\2=y/;
# Print and delete first line (CONFIG_SYS_EXTRA_OPTIONS), leaving
# CONFIG_TARGET_<BOARD> in pattern space
P;D;
};
# Move CONFIG_TARGET_<BOARD> to hold space
/^CONFIG_TARGET/{h;n}
# Print CONFIG_TARGET_<BOARD> after CONFIG_MACH_<SOC> in either SPL or
# normal mode.
/^CONFIG_MACH/{p;g;p;n};
/^\+S:CONFIG_MACH/{p;g;s/^CONFIG_TARGET/+S:&/;p;n};
# Print any remaining lines normally
p;
Run as:
sed -i -n -f t $(git grep -l CONFIG_ARCH_SUNXI configs/*)
and then manually removing the one instance of CONFIG_SYS_EXTRA_OPTIONS="" from
Colombus_defconfig
board/sunxi/Makefile was updated with:
sed -e 's/^\(obj-\$(CONFIG_\)\(.*\)\().*+= dram_.*\)/\1TARGET_\2\3/g' board/sunxi/Makefile
and manually retabbing a few lines to line up again.
The board descriptions could certainly be improved.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Ian Campbell [Fri, 24 Oct 2014 20:20:48 +0000 (21:20 +0100)]
sunxi: Drop FEL variants of defconfigs.
This can now be configured via Kconfig, e.g. with:
$ make BOARD_defconfig
$ echo CONFIG_SPL_FEL=y >> .config
$ echo CONFIG_SPL_FEL=y >> spl/.config
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Ian Campbell [Fri, 24 Oct 2014 20:20:47 +0000 (21:20 +0100)]
sunxi: Use CONFIG_MACH_SUN?I from Kconfig instead of CONFIG_SUN?I
Mostly automatic with:
sed -i -e 's/CONFIG_\(SUN[45678]I\)/CONFIG_MACH_\1/g' $(git grep -l CONFIG_SUN[45678]I)
followed by removing the relevant #defines from include/configs/sun?i.h by
hand.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Ian Campbell [Fri, 24 Oct 2014 20:20:46 +0000 (21:20 +0100)]
sunxi: Kconfig: Make SPL_FEL a toplevel Kconfig option
It's unfortunate that this needs to be present in both .config and spl/.config
since it makes it slightly hard to enable FEL mode for a regular defconfig. It
can be done with:
echo CONFIG_SPL_FEL=y >> .config
echo CONFIG_SPL_FEL=y >> spl/.config
Ideally only one of those would be needed.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Ian Campbell [Fri, 24 Oct 2014 20:20:45 +0000 (21:20 +0100)]
sunxi: kconfig: Rename TARGET_SUN[45678]I to MACH_SUN[45678]I.
Now we have CONFIG_ARCH_SUNXI as the toplevel, CONFIG_MACH_SUN[45678]I as the
per-SoC option and leave CONFIG_TARGET_BLAH free for individual boards in the
future.
Done automatically with:
sed -i -e 's/TARGET_\(SUN[45678]I\)/MACH_\1/g' $(git grep -l TARGET_SUN[45678]I)
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Ian Campbell [Fri, 24 Oct 2014 20:20:44 +0000 (21:20 +0100)]
sunxi: kconfig: Add top-level ARCH_SUNXI
And make TARGET_SUN[45678]I a choice variable under this.
configs updated with:
sed -i -e 's/^\(\+S:\)\?CONFIG_TARGET_SUN.I=y/\1CONFIG_ARCH_SUNXI=y\n&/g' configs/*
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Chen-Yu Tsai [Fri, 24 Oct 2014 08:07:25 +0000 (16:07 +0800)]
ARM: sunxi: Fix Ippo-q8h-v5 defconfig filename
The defconfig for Ippo-q8h-v5 was incorrectly committed as
"Ippo_q8h". This patch renames it correctly, as well as
correct a typo in my name in the maintainers listing.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Dirk Eibach [Mon, 3 Nov 2014 09:56:31 +0000 (10:56 +0100)]
ppc: Fix ppc4xx CONFIG_SYS_GENERIC_BOARD
I realized that with v2014.10 u-boot is not starting up on
ppc4xx boards with CONFIG_SYS_GENERIC_BOARD set.
I bisected it down to this:
d54d7eb support blackfin board initialization in generic board_f
With
d29437a ppc: Make ppc4xx ready for CONFIG_SYS_GENERIC_BOARD
I set gd to a defined value for ppc4xx in cpu_init_f().
I did not realize that the gd struct has also to be memset()
to zero at this point.
But at least commit d54d7eb assumes it is:
@@ -516,11 +528,13 @@ static int reserve_malloc(void)
/* (permanently) allocate a Board Info struct */
static int reserve_board(void)
{
- gd->start_addr_sp -= sizeof(bd_t);
- gd->bd = (bd_t *)map_sysmem(gd->start_addr_sp, sizeof(bd_t));
- memset(gd->bd, '\0', sizeof(bd_t));
- debug("Reserving %zu Bytes for Board Info at: %08lx\n",
- sizeof(bd_t), gd->start_addr_sp);
+ if (!gd->bd) {
+ gd->start_addr_sp -= sizeof(bd_t);
+ gd->bd = (bd_t *)map_sysmem(gd->start_addr_sp, sizeof(bd_t));
+ memset(gd->bd, '\0', sizeof(bd_t));
+ debug("Reserving %zu Bytes for Board Info at: %08lx\n",
+ sizeof(bd_t), gd->start_addr_sp);
+ }
return 0;
}
#endif
This might also be an issue on other architectures, so maintainers should
check.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Tom Rini [Tue, 4 Nov 2014 23:24:44 +0000 (18:24 -0500)]
Merge git://git.denx.de/u-boot-sh
Gerald Kerma [Fri, 31 Oct 2014 00:03:27 +0000 (01:03 +0100)]
ARM: kwimage: fix v0 format
This patch fix the kwimage tools for version 0 fileformat used for kirkwood
Tested on sheevaplug
Signed-off-by: Gerald Kerma <drEagle@doukki.net>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
Igor Grinberg [Mon, 3 Nov 2014 09:19:14 +0000 (11:19 +0200)]
MAINTAINERS: fix Pantelis Antoniou email address
Trivial fix (unless Pantelis has a new email address):
Pantelis Antoniou <panto.antoniou-consulting.com>
^
make it:
Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Vagrant Cascadian [Sun, 2 Nov 2014 01:09:01 +0000 (18:09 -0700)]
Fix cosmetic issues in mkimage manpage
* Escape use of - in description of -F.
* Fix line continuations in examples so that the continued lines are
also bold.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Masahiro Yamada [Fri, 31 Oct 2014 02:00:34 +0000 (11:00 +0900)]
kbuild: do not hide clang warnings during build with W=1
These lines originate in Linux; it looks like Linux folks chose to
hide bunch of warnings reported by clang rather than fixing C code.
In U-boot, warnings are being fixed thanks to Jeroen's great efforts.
Let's stop suppressing clang warnings.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Masahiro Yamada [Thu, 30 Oct 2014 06:30:58 +0000 (15:30 +0900)]
sparc: move CONFIG_SYS_TEXT_BASE to Kconfig
Defining CONFIG_SYS_TEXT_BASE in config.mk is very old style.
Create CONFIG_SYS_TEXT_BASE option in Kconfig, but let it
depend on CONFIG_SPARC because we do not want to disturb
the other architectures that still define CONFIG_SYS_TEXT_BASE
in their header files.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Masahiro Yamada [Thu, 30 Oct 2014 06:30:57 +0000 (15:30 +0900)]
sparc: merge CONFIG_SYS_CPU and CONFIG_SYS_VENDOR defines
For now, all the SPARC boards in U-Boot are provided by Gaisler.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Masahiro Yamada [Thu, 30 Oct 2014 06:30:56 +0000 (15:30 +0900)]
sparc: merge arch/sparc/cpu/*/config.mk to arch/sparc/config.mk
Remove arch/sparc/cpu/{leon2,leon3}/config.mk and move duplicated
defines of -fPIC to arch/sparc/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Masahiro Yamada [Thu, 30 Oct 2014 06:30:55 +0000 (15:30 +0900)]
sparc: move CONFIG_{LEON, LEON2, LEON3} to Kconfig
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Masahiro Yamada [Thu, 30 Oct 2014 06:30:54 +0000 (15:30 +0900)]
sparc: Use nicer prompt for board select menu
The Board names in the board select menu were simply taken from the
board directory name by a conversion tool when switching to Kconfig.
Let's use more descriptive prompts taken from
include/configs/gr*.h and board/gaisler/*/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Jeroen Hofstee [Mon, 27 Oct 2014 19:10:07 +0000 (20:10 +0100)]
serial: add prototypes for init functions
While at it, sort them.
Cc: Tom Rini <trini@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Jeroen Hofstee [Mon, 27 Oct 2014 19:10:06 +0000 (20:10 +0100)]
arm926ejs: cache: use __weak
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Jeroen Hofstee [Mon, 27 Oct 2014 21:27:18 +0000 (22:27 +0100)]
i2c: use __weak
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Tom Rini [Tue, 4 Nov 2014 15:46:45 +0000 (10:46 -0500)]
Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-staging
Tom Rini [Tue, 4 Nov 2014 12:00:48 +0000 (07:00 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-samsung
Nobuhiro Iwamatsu [Tue, 4 Nov 2014 00:56:42 +0000 (09:56 +0900)]
usb: ehci: rmobile: Collect up address data
R8A7791, R8A7793 and R8A7794 have same IP of USB controller.
This collect up address data of each SoCs.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Nobuhiro Iwamatsu [Tue, 4 Nov 2014 00:56:41 +0000 (09:56 +0900)]
usb: ehci: rmobile: Add support R8A7793
R8A7793 has same IP of USB controller as R8A7791 and R8A7794 of rmobile
ARM SoCs. This adds support R8A7793 to EHCI HCD of rmobile.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Hans de Goede [Wed, 24 Sep 2014 12:06:11 +0000 (14:06 +0200)]
usb: kbd: Add (optional) support for using an interrupt queue for polling
Waiting an interrupt packet to complete in usb_kbd_poll_for_event, causes
a 40 ms latency for each call to usb_kbd_testc, which is undesirable.
Using control messages leads to lower (but still not 0) latency, but some
devices do not work well with control messages (e.g. my kvm behaves funny
with them).
This commit adds support for using the int_queue mechanism which at least
the ehci-hcd driver supports. This allows polling with 0 latency, while
using interrupt packets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Wed, 24 Sep 2014 12:06:10 +0000 (14:06 +0200)]
usb: kbd: Cache pipe, interval and packetsize
Instead of looking them up every time we need them.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Wed, 24 Sep 2014 12:06:09 +0000 (14:06 +0200)]
stdio: Fix memleak on stdio_deregister
stdio_register makes a malloc-ed copy of struct stdio_dev through stdio_clone,
free the malloc-ed memory on stdio_deregister.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Wed, 24 Sep 2014 12:06:08 +0000 (14:06 +0200)]
usb: kbd: Fix memleak on usb_kbd_deregister()
Free the keyboard hid-report buffer and private data on deregister.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Wed, 24 Sep 2014 12:06:07 +0000 (14:06 +0200)]
usb: kbd: Remove unused usb_kbd_generic_poll function
This is not used anywhere, so lets remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Wed, 24 Sep 2014 12:06:06 +0000 (14:06 +0200)]
usb: Make pollable int support available outside of ehci-hcd.c
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Wed, 24 Sep 2014 12:06:05 +0000 (14:06 +0200)]
usb: ehci: Move cache invalidation to poll_int_queue
Preperation patch to use poll_int_queue outside of ehci-hcd.c .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Wed, 24 Sep 2014 12:06:04 +0000 (14:06 +0200)]
usb: ehci: Move interrupt packet length check to create_int_queue
Preperation patch to use create_int_queue outside of ehci-hcd.c .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Wed, 24 Sep 2014 12:06:03 +0000 (14:06 +0200)]
usb: ehci: Do not disable an already disabled periodic schedule
When periodic_schedules == 0, the schedule is disabled and there is no reason
to disable it again.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sat, 20 Sep 2014 15:03:53 +0000 (17:03 +0200)]
usb: Do not power-cycle usb devices on init
Do as the Linux kernel does and power on any ports which are not yet one,
this is enough.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sat, 20 Sep 2014 15:03:52 +0000 (17:03 +0200)]
usb: Remove unnecessary portnr lookup from usb_new_device
If the device has a parent, it is instantiated from usb_hub_port_connect_change
and the portnr is right there in dev->portnr, so there is no need for this
whole dance to look it up.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Nobuhiro Iwamatsu [Tue, 4 Nov 2014 00:15:48 +0000 (09:15 +0900)]
net: sh-eth: Add cache writeback control after setting bit of DMA descriptor
A bit field of DMA descriptor is on memory area of DMA. If we set data
to bit of DMA descriptor, we must be writeback data of DMA descriptor.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Tue, 4 Nov 2014 00:15:47 +0000 (09:15 +0900)]
net: sh-eth: Use memalign instead of orignal memroy alignment function
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Tue, 4 Nov 2014 00:15:46 +0000 (09:15 +0900)]
net: sh-eth: Remove definition of RX_DESC_SIZE and TX_DESC_SIZE
RX_DESC_SIZE and TX_DESC_SIZE mean the size of the data descriptor for sh-eth.
We can acquire this in sizeof. It is not necessary to define these in define.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Tue, 4 Nov 2014 00:14:38 +0000 (09:14 +0900)]
serial: sh: r8a7794: Add support external clock
The baud rate setting of external clock is enabled.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Tue, 4 Nov 2014 00:13:40 +0000 (09:13 +0900)]
net: sh-eth: Add support R8A7793
R8A7793 has the same sh-ether IP core as other SH/rmobile.
This patch adds support of R8A7793.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Tue, 4 Nov 2014 00:12:50 +0000 (09:12 +0900)]
serial: sh: Add support R8A7793
This adds the preset value to register for R8A7793.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Fri, 31 Oct 2014 07:30:27 +0000 (16:30 +0900)]
arm: rmobile: alt: Add VFAT filesystem support
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Fri, 31 Oct 2014 07:30:26 +0000 (16:30 +0900)]
arm: rmobile: alt: Add support USB and USB commands
This adds support for USB commands and USB storage device.
Signed-off-by: Yoshiyuki Ito <yoshiyuki.ito.ub@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Fri, 31 Oct 2014 07:30:25 +0000 (16:30 +0900)]
arm: rmobile: alt: Fix typo of SCIF id
Alt board use SCIF2, not SCIF0.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Fri, 31 Oct 2014 07:16:31 +0000 (16:16 +0900)]
arm: rmobile: alt: Remove RAM address initialization
Since board info structure is not still set up, the setting of RAM
address causes illegal access.
Therefore the setting of RAM address is removed.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Fri, 31 Oct 2014 07:16:30 +0000 (16:16 +0900)]
arm: rmobile: koelsch: Remove RAM address initialization
Since board info structure is not still set up, the setting of RAM
address causes illegal access.
Therefore the setting of RAM address is removed.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Fri, 31 Oct 2014 07:16:29 +0000 (16:16 +0900)]
arm: rmobile: lager: Remove RAM address initialization
Since board info structure is not still set up, the setting of RAM
address causes illegal access.
Therefore the setting of RAM address is removed.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Fri, 31 Oct 2014 07:16:28 +0000 (16:16 +0900)]
arm: rmobile: alt: Add external RAM boot
If CONFIG_RMOBILE_EXTRAM_BOOT is enabled, U-Boot is booted from External RAM.
The default boot address is 0x70000000.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Fri, 31 Oct 2014 07:16:27 +0000 (16:16 +0900)]
arm: rmobile: koelsch: Add external RAM boot
If CONFIG_RMOBILE_EXTRAM_BOOT is enabled, U-Boot is booted from External RAM.
The default boot address is 0x70000000.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Fri, 31 Oct 2014 07:16:26 +0000 (16:16 +0900)]
arm: rmobile: lager: Add external RAM boot
If CONFIG_RMOBILE_EXTRAM_BOOT is enabled, U-Boot is booted from External RAM.
The default boot address is 0xB0000000.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Fri, 31 Oct 2014 07:08:11 +0000 (16:08 +0900)]
arm: rmobile: lager: Fix change of the CPU frequency
The change of the CPU frequency is waited for until PLL0ST of the PLLECR is
set to 1.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Fri, 31 Oct 2014 07:07:16 +0000 (16:07 +0900)]
arm: rmobile: r8a7790: Update initialize L2 cache
Initialization of L2CTLR[5] was set only as R8A7790 by commit
237faf095fb43abbed6e40266ef7efccc8b9308b.
However, initialization of cash needs to be performed continuously.
This changes into the processing which continues initialization of
L2CTLR[5] into L2CTLR cash and performs it.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tom Rini [Mon, 3 Nov 2014 17:46:12 +0000 (12:46 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-mips
Tom Rini [Mon, 3 Nov 2014 17:43:42 +0000 (12:43 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-uniphier
Tom Rini [Mon, 3 Nov 2014 17:42:58 +0000 (12:42 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-spi
Fabio Estevam [Thu, 30 Oct 2014 20:46:37 +0000 (18:46 -0200)]
novena: Add MAINTAINERS file
Commit
f91c09acf5c58c ("ARM: mx6: Add support for Kosagi Novena") missed to
add a MAINTAINERS file, so add Marek as the maintainer.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Heiko Schocher [Thu, 30 Oct 2014 12:14:03 +0000 (13:14 +0100)]
arm, imx, spi: detect spi flash again on aristainetos board
155fa9af95a "spi: mxc: fix sf probe when using mxc_spi" break
spi flash detection on the aristainetos board. Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Ye.Li [Thu, 30 Oct 2014 10:53:49 +0000 (18:53 +0800)]
imx: mx6 sabreauto: Add board support for USB EHCI
On mx6 sabreauto board, there are two USB ports:
0: OTG
1: HOST
The EHCI driver is enabled for this board, but the IOMUX and VBUS power
control is not implemented, which cause both USB port failed to work.
This patch fix the problem by adding the board support codes.
Since the power control uses the GPIO pin from port expander MAX7310,
the PCA953X driver is enabled for accessing the MAX7310.
The ID pin of OTG Port needs to configure the GPR1 bit 13 for selecting
its daisy chain. Add a new function "imx_iomux_set_gpr_register" to
handle GPR register setting.
Signed-off-by: Ye.Li <B37916@freescale.com>
Ye.Li [Thu, 30 Oct 2014 10:30:54 +0000 (18:30 +0800)]
imx: mx6slevk: Add support for USDHC1 and USDHC3 slots
There are three SD/MMC sockets on mx6slevk boards. Implements the
full support for them.
The default boot socket is USDHC2, so the MMC environment is set
to that device.
Signed-off-by: Ye.Li <B37916@freescale.com>
Ye.Li [Thu, 30 Oct 2014 10:30:53 +0000 (18:30 +0800)]
imx: mx6sl: Add IOMUX setting for USDHC1-3
Set the USDHC1-3 IOMUX settings which are used for mx6slevk board.
Signed-off-by: Ye.Li <B37916@freescale.com>
Ye.Li [Thu, 30 Oct 2014 10:20:59 +0000 (18:20 +0800)]
imx: mx6: Enable high frequency clock source for GPT
Set the CONFIG_MXC_GPT_HCLK configuration in mx6_common.h, so that
24Mhz OSC clock source will be selected for GPT on all MX6 platforms.
Signed-off-by: Ye.Li <B37916@freescale.com>
Ye.Li [Thu, 30 Oct 2014 10:20:58 +0000 (18:20 +0800)]
imx: mx6sl: Set the preclk clock source to OSC 24Mhz
For MX6SL, uses the OSC 24Mhz as the preclk source in CCM. Align the
preclk setting with kernel.
Signed-off-by: Ye.Li <B37916@freescale.com>
Ye.Li [Thu, 30 Oct 2014 10:20:57 +0000 (18:20 +0800)]
imx: mx6: Change the get_ipg_per_clk for OSC 24Mhz source
For MX6SL and MX6SX, the perclk can come from OSC 24Mhz source. Fix
the get_ipg_per_clk function to support it.
Signed-off-by: Ye.Li <B37916@freescale.com>
Ye.Li [Thu, 30 Oct 2014 10:20:56 +0000 (18:20 +0800)]
imx: mx6sl: Add perclk_clk_sel bit define in CCM
The MX6SL has the perclk_clk_sel to select the perclk source. Add
its define in CCM
Signed-off-by: Ye.Li <B37916@freescale.com>
Ye.Li [Thu, 30 Oct 2014 10:20:55 +0000 (18:20 +0800)]
imx: gpt: Add High frequency clock source support for GPT
Introduce a new configuration "CONFIG_MXC_GPT_HCLK". When it is set,
the GPT will select a high frequency clock as clock source.
Otherwise, the GPT will stay to use 32Khz OSC as clock source.
In the implementation, since only the GPT on i.MX6 series provide the
clock source option for 24Mhz OSC. For others (only i.MX5 and i.MX6
compile the driver), if the configuration is set, the perclk will be
selected as clock source.
MX6Q/D Rev 1.0 and MX6SL are special in the implementation, because they
don't have the 24Mhz OSC clock source option, so also select the perclk
for them. For MX6SL, we will set the OSC 24Mhz to perclk in CCM, so
eventually the clock comes from OSC 24Mhz.
Signed-off-by: Ye.Li <B37916@freescale.com>
Ye.Li [Thu, 30 Oct 2014 09:54:08 +0000 (17:54 +0800)]
imximage: Fix the bootdata.size calculation
In system boot chapter of i.MX6 reference manual, the "Image Vector Table"
figure shows the bootdata.start points to the beginning of the destination
memory. It means the bootdata.size should contain the IVT offset part,
but the calculation in imximage tool does not have.
We found this issue when booting from QuadSPI NOR on i.MX6SX. The u-boot
runs into abnormal (crash or stop) after booting. After checked the destination
memory where the image is loaded to, there are hundreds of bytes at
the image end are not loaded into memory. Since there is a 4096 bytes
round in the calculation, for the booting devices using smaller IVT offset,
such as SD and SPI booting, they are not easy to reproduce.
Signed-off-by: Ye.Li <B37916@freescale.com>
Daniel Schwierzeck [Wed, 29 Oct 2014 16:30:36 +0000 (17:30 +0100)]
MIPS: add .padding section to linker script
Commit
79fd7e649e287228a1445820a72f7dd33baedb96
MIPS: always keep all sections in u-boot ELF binary.
Always keep all sections in u-boot ELF binary. Move all unneeded
sections after _end to avoid allocating space in the final binary.
Also remove .deadcode section which is now obsolete.
removed section .deadcode because the original symptoms were not
visible anymore. Unfortuneatly the binutils bug still exists.
The size of .rel.dyn section is often bigger than needed for all
entries. But objcopy only allocates space as much as required for all
reloc entries. Thus there is a gap between the last entry and
__rel_dyn_end in u-boot.bin. If u-boot is booted from RAM (e.g. in
SPL scenarios) that area could contain garbage data which could lead
to CPU exceptions during relocation.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Daniel Schwierzeck [Sun, 26 Oct 2014 13:16:23 +0000 (14:16 +0100)]
MIPS: refactor setting of compiler options
Refactor and unify all compiler settings in arch/mips/config.mk.
Also add tune flags for each supported CPU type.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Daniel Schwierzeck [Sun, 26 Oct 2014 13:14:07 +0000 (14:14 +0100)]
MIPS: kconfig: add options for vct board variant select
The vct board can be built with various variants which are
configured via CONFIG_SYS_EXTRA_OPTIONS. This is deprecated. Thus
add new Kconfig options for those board variants.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Daniel Schwierzeck [Sun, 26 Oct 2014 13:14:07 +0000 (14:14 +0100)]
MIPS: kconfig: add options for dbau1x00 board variant select
The dbau1x00 board can be built with various variants which are
configured via CONFIG_SYS_EXTRA_OPTIONS. This is deprecated. Thus
add new Kconfig options for those board variants.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Daniel Schwierzeck [Sun, 26 Oct 2014 13:14:07 +0000 (14:14 +0100)]
MIPS: kconfig: merge targets qemu_mips and qemu_mips64
Now the user can separately select the CPU type. Thus the
targets qemu_mips and qemu_mips64 can be merged to a single
target.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Daniel Schwierzeck [Sun, 26 Oct 2014 13:14:07 +0000 (14:14 +0100)]
MIPS: kconfig: globally define CONFIG_SYS_CPU for MIPS
Now the user can select the CPU type for each target. Thus
CONFIG_SYS_CPU could be set globally.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Daniel Schwierzeck [Sun, 26 Oct 2014 13:14:07 +0000 (14:14 +0100)]
MIPS: kconfig: add options for CPU type select
Add new Kconfig option to let the user select the targets
CPU type. Each target have to select SUPPORTS_CPU_MIPS[32,64]_R[1,2]
to indicate which CPU types are supported.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Daniel Schwierzeck [Sun, 26 Oct 2014 13:14:07 +0000 (14:14 +0100)]
MIPS: kconfig: add options for endianess select
Add new Kconfig option to let the user select the targets
endianess. Each target have to select SUPPORTS_BIG_ENDIAN
and/or SUPPORTS_LITTLE_ENDIAN to indicate which endianess
is supported.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Masahiro Yamada [Thu, 30 Oct 2014 06:50:15 +0000 (15:50 +0900)]
Remove the CREDITS file
This file is not maintained these days.
We use MAINTAINERS for the maintainership of the supported boards.
For dead boards, we have some clues in doc/README.scrapyard and
also imperishable history in git-log.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-By: Wolfgang Denk <wd@denx.de>
Fabio Estevam [Thu, 30 Oct 2014 20:46:37 +0000 (18:46 -0200)]
novena: Add MAINTAINERS file
Commit
f91c09acf5c58c ("ARM: mx6: Add support for Kosagi Novena") missed to
add a MAINTAINERS file, so add Marek as the maintainer.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Masahiro Yamada [Thu, 30 Oct 2014 09:29:15 +0000 (18:29 +0900)]
ppc/arm: remove remainders of dead boards in Kconfig
Commit
d58a9451e733 (ppc/arm: zap EMK boards) removed
TOP* boards support but missed to remove entries in Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Masahiro Yamada [Thu, 30 Oct 2014 09:28:01 +0000 (18:28 +0900)]
Remove unused files
[1] arch/arm/include/asm/arch-at91/at91_shdwn.h
The top9000 was the last board to use this header file.
It was removed by commit
d58a9451e733 (ppc/arm: zap EMK boards).
[2] board/matrix_vision/common/*
Some Matrix Vision boards were dropped by commit
e7a565638a7a
(powerpc: mpc83xx: remove board support for MERGERBOX and MVBLM7)
and commit
af55e35d3389
(powerpc: mpc5xxx: remove board support for MVBC_P and MVSMR).
Since then these files have been unused.
[3] include/usb/omap1510_udc.h
The omap5912osk was the last board to use this header file.
It was removed by commit
62d636aa2ac2
(omap: remove omap5912osk board support).
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-By: Wolfgang Denk <wd@denx.de>
Paul Kocialkowski [Tue, 28 Oct 2014 17:14:23 +0000 (18:14 +0100)]
twl4030: VMMC2 3.2V enable on MMC init
This enables the VMMC2 LDO, which powers the MMC2 device.
When the device starts from MMC2, this has already been enabled by the BootROM,
but when starting from peripheral boot (USB, UART), it is not the case.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Stefan Roese [Tue, 28 Oct 2014 10:32:24 +0000 (11:32 +0100)]
tools/kwbimage: Fix compilation warning
This patch fixes a compilation warning of kwbimage.c:
tools/kwbimage.c: In function ‘kwbimage_set_header’:
tools/kwbimage.c:784:8: warning: ‘headersz’ may be used uninitialized in this function [-Wmaybe-uninitialized]
memcpy(ptr, image, headersz);
^
Instead of using multiple if statements, use a switch statement with
a default entry. And return with error if an unsupported version
is configured in the cfg file.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-By: Wolfgang Denk <wd@denx.de>
Andreas Bießmann [Fri, 24 Oct 2014 21:39:11 +0000 (23:39 +0200)]
tools/kwbimage.c: fix build on darwin
kwbimage uses get_current_dir_name(3) which is a gnu extension and not
available on darwin host. Fix this by converting to portable getcwd(3)
function.
This patch fixes the following error:
---8<---
HOSTCC tools/kwbimage.o
tools/kwbimage.c:399:16: warning: implicit declaration of function 'get_current_dir_name' is invalid in C99 [-Wimplicit-function-declaration]
char *cwd = get_current_dir_name();
^
tools/kwbimage.c:399:10: warning: incompatible integer to pointer conversion initializing 'char *' with an expression of type 'int' [-Wint-conversion]
char *cwd = get_current_dir_name();
^ ~~~~~~~~~~~~~~~~~~~~~~
2 warnings generated.
...
Undefined symbols for architecture x86_64:
"_get_current_dir_name", referenced from:
_image_headersz_v1 in kwbimage.o
ld: symbol(s) not found for architecture x86_64
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
[agust: fixed getcwd() return warning]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Marek Vasut [Sat, 11 Oct 2014 22:00:50 +0000 (00:00 +0200)]
arm: mxs: Define bootscript env variable on m28evk
The patch below failed to define the variable, so define it
to make it consistent with M53EVK.
commit
a428ac914b2b6db851c1feac98622f2d9844db45
Author: Lothar Rubusch <lothar@denx.de>
Date: Thu Jun 26 11:01:29 2014 +0200
ARM: m28evk: Update default environment
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>