drm: bridge: adv7511: unregister cec i2c device after cec adapter

cec_unregister_adapter() assumes that the underlying adapter ops are
callable. For example, if the CEC adapter currently has a valid physical
address, then the unregistration procedure will invalidate the physical
address by setting it to f.f.f.f. Whence the following kernel oops
observed after removing the adv7511 module:

    Unable to handle kernel execution of user memory at virtual address 0000000000000000
    Internal error: Oops: 86000004 [#1] PREEMPT_RT SMP
    Call trace:
     0x0
     adv7511_cec_adap_log_addr+0x1ac/0x1c8 [adv7511]
     cec_adap_unconfigure+0x44/0x90 [cec]
     __cec_s_phys_addr.part.0+0x68/0x230 [cec]
     __cec_s_phys_addr+0x40/0x50 [cec]
     cec_unregister_adapter+0xb4/0x118 [cec]
     adv7511_remove+0x60/0x90 [adv7511]
     i2c_device_remove+0x34/0xe0
     device_release_driver_internal+0x114/0x1f0
     driver_detach+0x54/0xe0
     bus_remove_driver+0x60/0xd8
     driver_unregister+0x34/0x60
     i2c_del_driver+0x2c/0x68
     adv7511_exit+0x1c/0x67c [adv7511]
     __arm64_sys_delete_module+0x154/0x288
     invoke_syscall+0x48/0x100
     el0_svc_common.constprop.0+0x48/0xe8
     do_el0_svc+0x28/0x88
     el0_svc+0x1c/0x50
     el0t_64_sync_handler+0xa8/0xb0
     el0t_64_sync+0x15c/0x160
    Code: bad PC value
    ---[ end trace 0000000000000000 ]---

Protect against this scenario by unregistering i2c_cec after
unregistering the CEC adapter. Duly disable the CEC clock afterwards
too.

Fixes: 3b1b975003e4 ("drm: adv7511/33: add HDMI CEC support")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220612144854.2223873-3-alvin@pqrs.dk

drm: bridge: adv7511: fix CEC power down control register offset

The ADV7511_REG_CEC_CTRL = 0xE2 register is part of the main register
map - not the CEC register map. As such, we shouldn't apply an offset to
the register address. Doing so will cause us to address a bogus register
for chips with a CEC register map offset (e.g. ADV7533).

Fixes: 3b1b975003e4 ("drm: adv7511/33: add HDMI CEC support")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220612144854.2223873-2-alvin@pqrs.dk

drm: xlnx: add <linux/io.h> for readl/writel

Add a header file to prevent build errors:

../drivers/gpu/drm/xlnx/zynqmp_dp.c: In function ‘zynqmp_dp_write’:
../drivers/gpu/drm/xlnx/zynqmp_dp.c:335:9: error: implicit declaration of function ‘writel’ [-Werror=implicit-function-declaration]
  335 |         writel(val, dp->iomem + offset);
../drivers/gpu/drm/xlnx/zynqmp_dp.c: In function ‘zynqmp_dp_read’:
../drivers/gpu/drm/xlnx/zynqmp_dp.c:340:16: error: implicit declaration of function ‘readl’ [-Werror=implicit-function-declaration]
  340 |         return readl(dp->iomem + offset);

Fixes: a204f9743b68 ("drm: Remove linux/i2c.h from drm_crtc.h")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Hyun Kwon <hyun.kwon@xilinx.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220706184224.29116-1-rdunlap@infradead.org

drm/bridge: ti-sn65dsi86: Use atomic variants of drm_bridge_funcs

Move away from the deprecated enable/disable operations in
drm_bridge_funcs and enable atomic use.

v3:
 - Drop use of DRM_BRIDGE_STATE_OPS

v2:
 - fix build (kernel test robot <lkp@intel.com>)

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Kieran Bingham <kieran.bingham@ideasonboard.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220703202724.9553-2-sam@ravnborg.org

drm/bridge: fsl-ldb: Enable split mode for LVDS dual link

When LVDS dual link is used, we have to enable the LDB_CTRL_SPLIT_MODE bit.

Fixes: 463db5c2ed4a ("drm: bridge: ldb: Implement simple Freescale i.MX8MP LDB bridge")
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220701065634.4027537-3-victor.liu@nxp.com
Link: https://patchwork.freedesktop.org/patch/msgid/20220701065634.4027537-4-victor.liu@nxp.com

drm/bridge: fsl-ldb: Fix mode clock rate validation

With LVDS dual link, up to 160MHz mode clock rate is supported.
With LVDS single link, up to 80MHz mode clock rate is supported.
Fix mode clock rate validation by swapping the maximum mode clock
rates of the two link modes.

Fixes: 463db5c2ed4a ("drm: bridge: ldb: Implement simple Freescale i.MX8MP LDB bridge")
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220701065634.4027537-2-victor.liu@nxp.com

drm: bridge: ldb: Drop DE flip from Freescale i.MX8MP LDB bridge

The DE inversion is implemented in LCDIFv3 driver and is no longer
needed in the LDB bridge which does not invert the DE signal. Drop
the inversion.

Fixes: 463db5c2ed4ae ("drm: bridge: ldb: Implement simple Freescale i.MX8MP LDB bridge")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Robby Cai <robby.cai@nxp.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220630174031.92354-1-marex@denx.de

drm/bridge: anx7625: Add wait_hpd_asserted() callback

Move hpd polling check into wait_hpd_asserted() callback. For the cases
that aux transfer function wasn't used, do hpd polling check after pm
runtime resume, which will power on the bridge.

Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220706125254.2474095-5-hsinyi@chromium.org

drm/bridge: anx7625: Fix NULL pointer crash when using edp-panel

Move devm_of_dp_aux_populate_ep_devices() after pm runtime and i2c setup
to avoid NULL pointer crash.

edp-panel probe (generic_edp_panel_probe) calls pm_runtime_get_sync() to
read EDID. At this time, bridge should have pm runtime enabled and i2c
clients ready.

Fixes: adca62ec370c ("drm/bridge: anx7625: Support reading edid through aux channel")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220706125254.2474095-4-hsinyi@chromium.org

drm/bridge: anx7625: use pm_runtime_force_suspend(resume)

There's no need to check for IRQ or disable it in suspend.

Use pm_runtime_force_suspend(resume) to make sure anx7625 is powered off
correctly. Make the system suspend/resume and pm runtime suspend/resume
more consistent.

Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220706125254.2474095-3-hsinyi@chromium.org

drm/bridge: anx7625: Convert to devm_i2c_new_dummy_device()

Simplify the resource management.

Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220706125254.2474095-2-hsinyi@chromium.org

drm: Remove linux/i2c.h from drm_crtc.h

drm_crtc.h has no need for linux/i2c.h, so don't include it.
Avoids useless rebuilds of the entire universe when
touching linux/i2c.h.

Quite a few placs do currently depend on linux/i2c.h without
actually including it directly. All of those need to be
fixed up.

v2: imx and mcde need linux/io.h for readl()/etc.

Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220630195114.17407-5-ville.syrjala@linux.intel.com

drm: Remove linux/media-bus-format.h from drm_crtc.h

drm_crtc.h has no need for linux/media-bus-format.h, so don't
include it. Avoids useless rebuilds of the entire universe when
touching linux/media-bus-format.h.

Quite a few placs do currently depend on linux/media-bus-format.h
without actually including it directly. All of those need to be
fixed up.

v2: Deal with ingenic as well
v3: Fix up mxsfb and remaining parts of imx

Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220630195114.17407-4-ville.syrjala@linux.intel.com

drm: Remove linux/fb.h from drm_crtc.h

drm_crtc.h has no need for linux/fb.h, so don't include it.
Avoids useless rebuilds of the entire universe when
touching linux/fb.h.

Quite a few placs do currently depend on linux/fb.h or other
headers pulled in by it without actually including any of it
directly. All of those need to be fixed up.

v2: Split the vmwgfx change out

Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220630195114.17407-3-ville.syrjala@linux.intel.com

drm/vmwgfx: Stop using 'TRUE'

Stop using the 'TRUE' define. This ultimately gets defined by
acpi/actypes.h that gets included here via a convoluted chain of
other headers. drm_crtc.h is part of that chain, and I'm trying
to eliminate all unnecessary includes from it to avoid pointless
rebuilds.

v2: Split out from the bigger patch

Cc: Zack Rusin <zackr@vmware.com>
Cc: VMware Graphics Reviewers <linux-graphics-maintainer@vmware.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220630195114.17407-2-ville.syrjala@linux.intel.com
Reviewed-by: Zack Rusin <zackr@vmware.com<mailto:zackr@vmware.com>>

drm: bridge: sii8620: fix possible off-by-one

The next call to sii8620_burst_get_tx_buf will result in off-by-one
When ctx->burst.tx_count + size == ARRAY_SIZE(ctx->burst.tx_buf). The same
thing happens in sii8620_burst_get_rx_buf.

This patch also change tx_count and tx_buf to rx_count and rx_buf in
sii8620_burst_get_rx_buf. It is unreasonable to check tx_buf's size and
use rx_buf.

Fixes: e19e9c692f81 ("drm/bridge/sii8620: add support for burst eMSC transmissions")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220518065856.18936-1-hbh25y@gmail.com

drm/ingenic: Use the highest possible DMA burst size

Until now, when running at the maximum resolution of 1280x720 at 32bpp
on the JZ4770 SoC the output was garbled, the X/Y position of the
top-left corner of the framebuffer warping to a random position with
the whole image being offset accordingly, every time a new frame was
being submitted.

This problem can be eliminated by using a bigger burst size for the DMA.

Set in each soc_info structure the maximum burst size supported by the
corresponding SoC, and use it in the driver.

Set the new value using regmap_update_bits() instead of
regmap_set_bits(), since we do want to override the old value of the
burst size. (Note that regmap_set_bits() wasn't really valid before for
the same reason, but it never seemed to be a problem).

Cc: <stable@vger.kernel.org>
Fixes: 90b86fcc47b4 ("DRM: Add KMS driver for the Ingenic JZ47xx SoCs")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20220702230727.66704-1-paul@crapouillou.net
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Christophe Branchereau <cbranchereau@gmail.com>

drm/panel: simple: add ETML0700Y5DHA panel

Add support for the 1024x600 LVDS panel.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220530122407.918874-2-m.felsch@pengutronix.de

dt-bindings: display: simple: add EDT ETML0700Y5DHA panel

Add binding for the Emerging Display Technology ETML0700Y5DHA panel.
It is a 7" WSVGA (1024x600) TFT LCD panel with:
 - LVDS data interface,
 - backlight and
 - capacitive touch.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220530122407.918874-1-m.felsch@pengutronix.de

drm/panel: simple: Add support for HannStar HSD101PWW2 panel

Add definition of the HannStar HSD101PWW2 Rev0-A00/A01 LCD
SuperIPS+ HD panel.

Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220529180548.9942-4-clamor95@gmail.com

dt-bindings: display: simple: Add HannStar HSD101PWW2

Add HannStar HSD101PWW2 10.1" WXGA (1280x800) TFT-LCD LVDS panel
to the list of compatibles.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220529180548.9942-3-clamor95@gmail.com

dt-bindings: sharp,lq101r1sx01: Add compatible for LQ101R1SX03

LQ101R1SX03 is compatible with LQ101R1SX01 from software perspective,
document it. The LQ101R1SX03 is a newer revision of LQ101R1SX01, it has
minor differences in hardware pins in comparison to the older version.
The newer version of the panel can be found on Android tablets, like
ASUS TF701T.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Anton Bambura <jenneron@protonmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220529180548.9942-2-clamor95@gmail.com

drm/rockchip: Fix an error handling path rockchip_dp_probe()

Should component_add() fail, we should call analogix_dp_remove() in the
error handling path, as already done in the remove function.

Fixes: 152cce0006ab ("drm/bridge: analogix_dp: Split bind() into probe() and real bind()")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/b719d9061bb97eb85145fbd3c5e63f4549f2e13e.1655572071.git.christophe.jaillet@wanadoo.fr

drm/rockchip: vop: Don't crash for invalid duplicate_state()

It's possible for users to try to duplicate the CRTC state even when the
state doesn't exist. drm_atomic_helper_crtc_duplicate_state() (and other
users of __drm_atomic_helper_crtc_duplicate_state()) already guard this
with a WARN_ON() instead of crashing, so let's do that here too.

Fixes: 4e257d9eee23 ("drm/rockchip: get rid of rockchip_drm_crtc_mode_config")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220617172623.1.I62db228170b1559ada60b8d3e1637e1688424926@changeid

drm/bridge: imx: i.MX8 bridge drivers should depend on ARCH_MXC

The various Freescale i.MX8 display bridges are only present on
Freescale i.MX8 SoCs.  Hence add a dependency on ARCH_MXC, to prevent
asking the user about these drivers when configuring a kernel without
i.MX SoC support.

Fixes: e60c4354840b2fe8 ("drm/bridge: imx: Add LDB support for i.MX8qm")
Fixes: 3818715f62b42b5c ("drm/bridge: imx: Add LDB support for i.MX8qxp")
Fixes: 96988a526c97cfbe ("drm/bridge: imx: Add i.MX8qxp pixel link to DPI support")
Fixes: 1ec17c26bc06289d ("drm/bridge: imx: Add i.MX8qm/qxp display pixel link support")
Fixes: 93e163a9e0392aca ("drm/bridge: imx: Add i.MX8qm/qxp pixel combiner support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/42c542b53a1c8027b23a045045fbb7b34479913d.1656072500.git.geert+renesas@glider.be

drm: Remove unnecessary junk from drm_crtc.h

drm_crtc.h is including several entirely unnecessary headers,
and also contains unused forward declarations. Remove it all.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220613200317.11305-6-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>

drm/edid: take HF-EEODB extension count into account

Take the HF-EEODB extension count override into account.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c31b5796feb05c3ebac067600be2e88e098d7592.1656494768.git.jani.nikula@intel.com

drm/edid: add HF-EEODB support to EDID read and allocation

HDMI 2.1 section 10.3.6 defines an HDMI Forum EDID Extension Override
Data Block, which may contain a different extension count than the base
block claims. Add support for reading more EDID data if available. The
extra blocks aren't parsed yet, though.

Hard-coding the EEODB parsing instead of using the iterators we have is
a bit of a bummer, but we have to be able to do this on a partially
allocated EDID while reading it.

v2:
- Check for CEA Data Block Collection size (Ville)
- Amend commit message and comment about hard-coded parsing

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/57b57a355d62eb91ad1e3cf555978576f2bd9fdd.1656494768.git.jani.nikula@intel.com

drm/edid: do invalid block filtering in-place

Rewrite edid_filter_invalid_blocks() to filter invalid blocks
in-place. The main motivation is to not rely on passed in information on
invalid block count or the allocation size, which will be helpful in
follow-up work on HF-EEODB.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a6ad5e4e7b91338c0d19d7be189af31094e65555.1656494768.git.jani.nikula@intel.com

drm/edid: add drm_edid_raw() to access the raw EDID data

Unfortunately, there are still plenty of interfaces around that require
a struct edid pointer, and it's impossible to change them all at
once. Add an accessor to the raw EDID data to help the transition.

While there are no such cases now, be defensive against raw EDID
extension count indicating bigger EDID than is actually allocated.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/fb55d0b580d556bf2b8e58070239657ac9cb4b2f.1656494768.git.jani.nikula@intel.com

drm/probe-helper: add drm_connector_helper_get_modes()

Add a helper function to be used as the "default" .get_modes()
hook. This also works as an example of what the driver .get_modes()
hooks are supposed to do regarding the new drm_edid_read*() and
drm_edid_connector_update() calls.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d985449ed4b95971490ab7c09d2d59b58a892769.1656494768.git.jani.nikula@intel.com

drm/edid: add drm_edid_connector_update()

Add a new function drm_edid_connector_update() to replace the
combination of calls drm_connector_update_edid_property() and
drm_add_edid_modes(). Usually they are called in the drivers in this
order, however the former needs information from the latter.

Since the new drm_edid_read*() functions no longer call the connector
updates directly, and the read and update are separated, we'll need this
new function for the connector update.

This is all in drm_edid.c simply to keep struct drm_edid opaque.

v2:
- Share code with drm_connector_update_edid_property() (Ville)
- Add comment about override EDID handling

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/75aa3dbc8c9aa26ebbcdeacd98a466ef8d8827f4.1656494768.git.jani.nikula@intel.com

drm/edid: abstract debugfs override EDID set/reset

Add functions drm_edid_override_set() and drm_edid_override_reset() to
support "edid_override" connector debugfs, and to hide the details about
it in drm_edid.c. No functional changes at this time.

Also note in the connector.override_edid flag kernel-doc that this is
only supposed to be modified by the code doing debugfs EDID override
handling. Currently, it is still being modified by amdgpu in
create_eml_sink() and handle_edid_mgmt() for reasons unknown. This was
added in commit 4562236b3bc0 ("drm/amd/dc: Add dc display driver (v2)")
and later moved to amdgpu_dm.c in commit e7b07ceef2a6 ("drm/amd/display:
Merge amdgpu_dm_types and amdgpu_dm").

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8f6b4001630cafac5f44aa5913429ac9979743d2.1656494768.git.jani.nikula@intel.com

drm/edid: clean up connector update error handling and debug logging

Bail out on all errors, debug log all errors, and convert to drm device
based debug logging.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/de4270b3d2e61fe42b9248490376594d472d19aa.1656494768.git.jani.nikula@intel.com

drm/edid: convert drm_connector_update_edid_property() to struct drm_edid

Make drm_connector_update_edid_property() a thin wrapper around a struct
drm_edid based version of the same.

This lets us remove the legacy drm_update_tile_info() and
drm_add_display_info() functions altogether.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/4bfe87ae392554ffb41d725353c4265ae56700bb.1656494768.git.jani.nikula@intel.com

drm/edid: move drm_connector_update_edid_property() to drm_edid.c

The function needs access to drm_edid.c internals more than
drm_connector.c. We can make drm_reset_display_info(),
drm_add_display_info() and drm_update_tile_info() static. There will be
more benefits with follow-up struct drm_edid refactoring.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/cbabce6ffb41fdc903533f21d946e8cae0667be5.1656494768.git.jani.nikula@intel.com

drm/vc4: change vc4_dma_range_matches from a global to static

sparse reports
drivers/gpu/drm/vc4/vc4_drv.c:270:27: warning: symbol 'vc4_dma_range_matches' was not declared. Should it be static?

vc4_dma_range_matches is only used in vc4_drv.c, so it's storage class specifier
should be static.

Fixes: da8e393e23ef ("drm/vc4: drv: Adopt the dma configuration from the HVS or V3D component")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220629200101.498138-1-trix@redhat.com

iosys-map: Add per-word write

Like was done for read, provide the equivalent for write. Even if
current users are not in the hot path, this should future-proof it.

v2:
  - Remove default from _Generic() - callers wanting to write more
    than u64 should use iosys_map_memcpy_to()
  - Add WRITE_ONCE() cases dereferencing the pointer when using system
    memory
v3:
  - Fix precedence issue when casting inside WRITE_ONCE(). By not using ()
    around vaddr__ the offset was not part of the cast, but rather added
    to it, producing a wrong address
  - Remove compiletime_assert() as WRITE_ONCE() already contains it

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Reviewed-by: Christian König <christian.koenig@amd.com> # v1
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220628191016.3899428-2-lucas.demarchi@intel.com

iosys-map: Add per-word read

Instead of always falling back to memcpy_fromio() for any size, prefer
using read{b,w,l}(). When reading struct members it's common to read
individual integer variables individually. Going through memcpy_fromio()
for each of them poses a high penalty.

Employ a similar trick as __seqprop() by using _Generic() to generate
only the specific call based on a type-compatible variable.

For a pariticular i915 workload producing GPU context switches,
__get_engine_usage_record() is particularly hot since the engine usage
is read from device local memory with dgfx, possibly multiple times
since it's racy. Test execution time for this test shows a ~12.5%
improvement with DG2:

Before:
nrepeats = 1000; min = 7.63243e+06; max = 1.01817e+07;
median = 9.52548e+06; var = 526149;
After:
nrepeats = 1000; min = 7.03402e+06; max = 8.8832e+06;
median = 8.33955e+06; var = 333113;

Other things attempted that didn't prove very useful:
1) Change the _Generic() on x86 to just dereference the memory address
2) Change __get_engine_usage_record() to do just 1 read per loop,
   comparing with the previous value read
3) Change __get_engine_usage_record() to access the fields directly as it
   was before the conversion to iosys-map

(3) did gave a small improvement (~3%), but doesn't seem to scale well
to other similar cases in the driver.

Additional test by Chris Wilson using gem_create from igt with some
changes to track object creation time. This happens to accidentally
stress this code path:

Pre iosys_map conversion of engine busyness:
lmem0: Creating    262144 4KiB objects took 59274.2ms

Unpatched:
lmem0: Creating    262144 4KiB objects took 108830.2ms

With readl (this patch):
lmem0: Creating    262144 4KiB objects took 61348.6ms

s/readl/READ_ONCE/
lmem0: Creating    262144 4KiB objects took 61333.2ms

So we do take a little bit more time than before the conversion, but
that is due to other factors: bringing the READ_ONCE back would be as
good as just doing this conversion.

v2:
  - Remove default from _Generic() - callers wanting to read more
    than u64 should use iosys_map_memcpy_from()
  - Add READ_ONCE() cases dereferencing the pointer when using system
    memory
v3:
  - Fix precedence issue when casting inside READ_ONCE(). By not using ()
    around vaddr__ the offset was not part of the cast, but rather added
    to it, producing a wrong address
  - Remove compiletime_assert() as READ_ONCE() already contains it

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com> # v1
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220628191016.3899428-1-lucas.demarchi@intel.com

drm: lcdif: Add support for i.MX8MP LCDIF variant

Add support for i.MX8MP LCDIF variant. This is called LCDIFv3 and is
completely different from the LCDIFv3 found in i.MX23 in that it has
a completely scrambled register layout compared to all previous LCDIF
variants. The new LCDIFv3 also supports 36bit address space.

Add a separate driver which is really a fork of MXSFB driver with the
i.MX8MP LCDIF variant handling filled in.

Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexander Stein <alexander.stein@ew.tq-group.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Robby Cai <robby.cai@nxp.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stefan Agner <stefan@agner.ch>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220628174152.167284-2-marex@denx.de

dt-bindings: lcdif: Add compatible for i.MX8MP

Add compatible string for i.MX8MP LCDIF variant. This is called LCDIFv3
and is completely different from the LCDIFv3 found in i.MX23 in that it
has a completely scrambled register layout compared to all previous LCDIF
variants. The new LCDIFv3 also supports 36bit address space. However,
except for the complete bit reshuffling, this is still LCDIF and it still
works like one.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexander Stein <alexander.stein@ew.tq-group.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Robby Cai <robby.cai@nxp.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: devicetree@vger.kernel.org
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220628174152.167284-1-marex@denx.de

drm/bridge: tc358767: Do not cache dsi_lanes twice

The DSI lane count can be accessed via the dsi device pointer,
make use of that. No functional change.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220624181902.151959-1-marex@denx.de

drm/display/selftests: drop extra word 'for' in comments for MST selftests

there is an unexpected word 'for' in the comments that need to be dropped

file - ./drivers/gpu/drm/selftests/test-drm_dp_mst_helper.c
line - 3

* Test cases for for the DRM DP MST helpers

changed to:

* Test cases for the DRM DP MST helpers

Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220623100632.27056-1-jiangjian@cdjrlc.com

drm/vc4: hdmi: Move pixel doubling from Pixelvalve to HDMI block

With the change to 2 pixels/clock, the pixel doubling in the PV
results in doubling each pair of pixels, ie ABABCDCD instead of
AABBCCDD.

Move the pixel doubling to the HDMI block, however this means
that DBLCLK modes now fall foul of requiring even values for
all the horizontal timing parameters.
As both 480i and 576i fail this, attempt to fix up DBLCLK modes
that have odd timings values.

Fixes: 8323989140f3 ("drm/vc4: hdmi: Support the BCM2711 HDMI controllers")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-34-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Correct HDMI timing registers for interlaced modes

For interlaced modes the timings were not being correctly
programmed into the HDMI block, so correct them.

Fixes: 8323989140f3 ("drm/vc4: hdmi: Support the BCM2711 HDMI controllers")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-33-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Force modeset when bpc or format changes

Whenever the maximum BPC is changed, vc4_hdmi_encoder_compute_config()
might pick up a different BPC or format depending on the display
capabilities.

That change will have a number of side effects, including the clock
rates and whether the scrambling is enabled.

However, only drm_crtc_state.connectors_changed will be set to true,
since that properly only affects the connector.

This means that while drm_atomic_crtc_needs_modeset() will return true,
and thus drm_atomic_helper_commit_modeset_enables() will call our
encoder atomic_enable() hook, mode_changed will be false.

So crtc_set_mode() will not call our encoder .atomic_mode_set() hook. We
use this hook in vc4 to set the vc4_hdmi_connector_state.output_bpc (and
output_format), and will then reuse the value in .atomic_enable() to select
whether or not scrambling should be enabled.

However, since our clock rate is pre-computed during .atomic_check(), we
end up with the clocks properly configured, but the scrambling disabled,
leading to a blank screen.

Let's set mode_changed to true in our HDMI driver to force the update of
output_bpc, and thus prevent the issue entirely.

Fixes: ba8c0faebbb0 ("drm/vc4: hdmi: Enable 10/12 bpc output")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-32-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Fix timings for interlaced modes

Increase the number of post-sync blanking lines on odd fields instead of
decreasing it on even fields. This makes the total number of lines
properly match the modelines.

Additionally fix the value of PV_VCONTROL_ODD_DELAY, which did not take
pixels_per_clock into account, causing some displays to invert the
fields when driven by bcm2711.

Fixes: 682e62c45406 ("drm/vc4: Fix support for interlaced modes on HDMI.")
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-31-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Report that 3d/stereo is allowed

Our HDMI controllers supports Stereo output so let's enable it.

Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-30-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Add MISC_CONTROL register for vc4

The MISC_CONTROL register allows configuration of pixel repetition
for pixel doubling in the HDMI block instead of PixelValve.
It was already defined for vc5, so add it for vc4.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-29-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Add HDMI format detection registers to register list

The block can detect what the incoming image timings are for
debug purposes. Add them to the list of registers understood
by the driver to allow easy dumping of the values.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-28-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Remove VC4_HDMI_SCHEDULER_CONTROL_VERT_ALWAYS_KEEPOUT

This bit ensures data island packets are never generated when disallowed
by HDCP. As no Pi boards support HDCP this is providing an unnecessary
restriction

Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-27-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Skip writes to disabled packet RAM

This path actually occurs when audio is started during a hdmi mode set.
As the data will be written by vc4_hdmi_set_infoframes when packet RAM
is enabled again, don't treat as an error

Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-26-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Stop checking for enabled output in audio

The current HDMI driver, in vc4_hdmi_audio_can_stream() checks whether
the display output is enabled.

This has been there in one form or the other since the introduction of
the audio support in the VC4 HDMI driver in commit bb7d78568814
("drm/vc4: Add HDMI audio support"), but no justification for this check
is in the commit message, or in the discussions around the patches.

One can only assume this was done to prevent a user from playing audio
on the ALSA soundcard when the monitor doesn't support it.

However, this is causing some issues. Indeed, Kodi, for example, was
hitting some errors if it was streaming audio during a modeset. With the
theory above, it does make sense, but the display and audio threads are
typically completely different processes with no opportunity to
synchronise which makes it hard to workaround.

Removing that check also doesn't seem to cause any trouble, so let's
just remove it.

Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-25-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Move HDMI reset to pm_resume

The BCM2835-37 found in the RaspberryPi 0 to 3 have a power domain
attached to the HDMI block, handled in Linux through runtime_pm.

That power domain is shared with the VEC block, so even if we put our
runtime_pm reference in the HDMI driver it would keep being on. If the
VEC is disabled though, the power domain would be disabled and we would
lose any initialization done in our bind implementation.

That initialization involves calling the reset function and initializing
the CEC registers.

Let's move the initialization to our runtime_resume implementation so
that we initialize everything properly if we ever need to.

Fixes: c86b41214362 ("drm/vc4: hdmi: Move the HSM clock enable to runtime_pm")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-24-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Switch to pm_runtime_status_suspended

If the controller isn't clocked or its domain powered up, the register
accesses will either stall the CPU or return garbage, respectively.

Thus, we had a warning in our register access function to complain when
that kind of risky accesses were performed.

In order to check the runtime_pm power state, we were using
pm_runtime_active(), but it turns out that it will become active only
once the runtime_resume hook has been executed.

This prevents us from doing any WARN-free register access in our
runtime_resume() implementation, while this is valid.

Let's switch to pm_runtime_status_suspended() instead.

Fixes: 14e193b95604 ("drm/vc4: hdmi: Warn if we access the controller while disabled")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-23-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Reset HDMI MISC_CONTROL register

The HDMI block can repeat pixels for double clocked modes,
and the firmware is now configuring the block to do this as
the PV is doing it incorrectly when at 2pixels/clock.
If the kernel doesn't reset it then we end up with strange
modes.

Reset MISC_CONTROL.

Fixes: 8323989140f3 ("drm/vc4: hdmi: Support the BCM2711 HDMI controllers")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-22-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Avoid full hdmi audio fifo writes

We are getting occasional VC4_HD_MAI_CTL_ERRORF in
HDMI_MAI_CTL which seem to correspond with audio dropouts.

Reduce the threshold where we deassert DREQ to avoid the fifo
overfilling

Fixes: bb7d78568814 ("drm/vc4: Add HDMI audio support")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-21-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Clear unused infoframe packet RAM registers

Using a hdmi analyser the bytes in packet ram
registers beyond the length were visible in the
infoframes and it flagged the checksum as invalid.

Zeroing unused words of packet RAM avoids this

Fixes: 21317b3fba54 ("drm/vc4: Set up the AVI and SPD infoframes.")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-20-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Add all the vc5 HDMI registers into the debugfs dumps

The vc5 HDMI registers hadn't been added into the debugfs
register sets, therefore weren't dumped on request.
Add them in.

Fixes: 8323989140f3 ("drm/vc4: hdmi: Support the BCM2711 HDMI controllers")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-19-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hdmi: Disable audio if dmas property is present but empty

The dmas property is used to hold the dmaengine channel used for audio
output.

Older device trees were missing that property, so if it's not there we
disable the audio output entirely.

However, some overlays have set an empty value to that property, mostly
to workaround the fact that overlays cannot remove a property. Let's add
a test for that case and if it's empty, let's disable it as well.

Cc: <stable@vger.kernel.org>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Link: https://lore.kernel.org/r/20220613144800.326124-18-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: dsi: Add correct stop condition to vc4_dsi_encoder_disable iteration

vc4_dsi_encoder_disable is partially an open coded version of
drm_bridge_chain_disable, but it missed a termination condition
in the loop for ->disable which meant that no post_disable
calls were made.

Add in the termination clause.

Fixes: 033bfe7538a1 ("drm/vc4: dsi: Fix bridge chain handling")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-17-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: dsi: Fix dsi0 interrupt support

DSI0 seemingly had very little or no testing as a load of
the register mappings were incorrect/missing, so host
transfers always timed out due to enabling/checking incorrect
bits in the interrupt enable and status registers.

Fixes: 4078f5757144 ("drm/vc4: Add DSI driver")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-16-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: dsi: Register dsi0 as the correct vc4 encoder type

vc4_dsi was registering both dsi0 and dsi1 as VC4_ENCODER_TYPE_DSI1
which seemed to work OK for a single DSI display, but fails
if there are two DSI displays connected.

Update to register the correct type.

Fixes: 4078f5757144 ("drm/vc4: Add DSI driver")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-15-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: dsi: Correct pixel order for DSI0

For slightly unknown reasons, dsi0 takes a different pixel format
to dsi1, and that has to be set in the pixel valve.

Amend the setup accordingly.

Fixes: a86773d120d7 ("drm/vc4: Add support for feeding DSI encoders from the pixel valve.")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-14-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: dsi: Correct DSI divider calculations

The divider calculations tried to find the divider just faster than the
clock requested. However if it required a divider of 7 then the for loop
aborted without handling the "error" case, and could end up with a clock
lower than requested.

The integer divider from parent PLL to DSI clock is also capable of
going up to /255, not just /7 that the driver was trying.  This allows
for slower link frequencies on the DSI bus where the resolution permits.

Correct the loop so that we always have a clock greater than requested,
and covering the whole range of dividers.

Fixes: 86c1b9eff3f2 ("drm/vc4: Adjust modes in DSI to work around the integer PLL divider.")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-13-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: dsi: Release workaround buffer and DMA

On Pi0-3 the driver allocates a buffer and requests a DMA channel
because the ARM can't write to DSI1's registers directly.

However, we never release that buffer or channel. Let's add a
device-managed action to release each.

Fixes: 4078f5757144 ("drm/vc4: Add DSI driver")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-12-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: dpi: Ensure a default format is selected

In a couple of error/incomplete configuration cases, the
DPI_FORMAT bits wouldn't get set.

Enforce our RGB888 default in all these cases.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-11-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: dpi: Add option for inverting pixel clock and output enable

DRM provides flags for inverting pixel clock and output enable
signals, but these were not mapped to the relevant registers.

Add those mappings.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-10-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: dpi: Add support for composite syncs to vc4_dpi

The hardware can combine H&V syncs onto the output enable line
as composite syncs, so add the relevant configuration to do that.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-9-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: hvs: Add debugfs node that dumps the current display lists

This allows easy analysis of display lists when debugging.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-8-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: plane: Add alpha_blend_mode property to each plane.

Move from only supporting the default of pre-multiplied
alpha to supporting user specified blend mode using the
standardised property.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-7-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: plane: Fix margin calculations for the right/bottom edges

The current plane margin calculation code clips the right and bottom
edges of the range based using the left and top margins.

This is obviously wrong, so let's fix it.

Fixes: 666e73587f90 ("drm/vc4: Take margin setup into account when updating planes")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-6-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: plane: Remove subpixel positioning check

There is little harm in ignoring fractional coordinates
(they just get truncated).

Without this:
modetest -M vc4 -F tiles,gradient -s 32:1920x1080-60 -P89@74:1920x1080*.1.1@XR24

is rejected. We have the same issue in Kodi when trying to
use zoom options on video.

Note: even if all coordinates are fully integer. e.g.
src:[0,0,1920,1080] dest:[-10,-10,1940,1100]

it will still get rejected as drm_atomic_helper_check_plane_state
uses drm_rect_clip_scaled which transforms this to fractional src coords

Fixes: 21af94cf1a4c ("drm/vc4: Add support for scaling of display planes.")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-5-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: kms: Use maximum FIFO load for the HVS clock rate

The core clock computation takes into account both the load due to the
input (ie, planes) and its output (ie, encoders).

However, while the input load needs to consider all the planes, and thus
sum all of their associated loads, the output happens mostly in
parallel.

Therefore, we need to consider only the maximum of all the output loads,
and not the sum like we were doing. This resulted in a clock rate way
too high which could be discarded for being too high by the clock
framework.

Since recent changes, the clock framework will even downright reject it,
leading to a core clock being too low for its current needs.

Fixes: 16e101051f32 ("drm/vc4: Increase the core clock based on HVS load")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-4-maxime@cerno.tech

drm/vc4: kms: Warn if clk_set_min_rate fails

We currently ignore the clk_set_min_rate return code assuming it would
succeed. However, it can fail if we ask for a rate higher than the
current maximum for example.

Since we can't fail in atomic_commit, at least warn on failure.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-3-maxime@cerno.tech

drm/vc4: drv: Adopt the dma configuration from the HVS or V3D component

vc4_drv isn't necessarily under the /soc node in DT as it is a
virtual device, but it is the one that does the allocations.
The DMA addresses are consumed by primarily the HVS or V3D, and
those require VideoCore cache alias address mapping, and so will be
under /soc.

During probe find the a suitable device node for HVS or V3D,
and adopt the DMA configuration of that node.

Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-2-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/fourcc: Document the Intel CCS modifiers' CC plane expected pitch

The driver expects the pitch of the Intel CCS CC color planes to be
64 bytes aligned, adjust the modifier descriptions accordingly.

Cc: Nanley Chery <nanley.g.chery@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Nanley Chery <nanley.g.chery@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220623144955.2486736-1-imre.deak@intel.com

drm/doc: Fix comment typo

Replace apprpriately with appropriately.

Fixes: 1e4d84c6589e9 ("drm/doc: Polish plane composition property docs")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Simon Ser <contact@emersion.fr>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20220628003407.77765-1-marex@denx.de

drm/stm: ltdc: update hardware error management

The latest hardware version (0x40100) supports a hardware threshold
register (aka FUTR) to trigger a fifo underrun interrupt.
A software threshold has been implemented for other hardware versions.
The threshold is set to 128 by default.

Signed-off-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220603134654.594373-1-yannick.fertre@foss.st.com

drm/stm: ltdc: add support of horizontal & vertical mirroring

Support of vertical & horizontal mirroring features thanks to
the plane rotation property.

Signed-off-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220603134547.593790-1-yannick.fertre@foss.st.com

drm/stm: ltdc: add support of the dynamic z-order

Zpos property is immutable for all hardware versions except the last
version (0x40100) which support the blending order feature
(dynamic z-order).

Signed-off-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220603134459.593379-1-yannick.fertre@foss.st.com

drm/stm: ltdc: fix various coding-style warnings

Fix issues reported by checkpatch.pl:
- Braces {} should be used on all arms
- Blank lines

Signed-off-by: Yannick Fertre <yannick.fertre@foss.st.com>
Acked-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220603134334.592805-1-yannick.fertre@foss.st.com

drm/stm: ltdc: remove error message about scaling

Remove error message about scaling & replace it by a debug
message to avoid too much error.

Signed-off-by: Yannick Fertre <yannick.fertre@foss.st.com>
Acked-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220603134250.592408-1-yannick.fertre@foss.st.com

drm/stm: ltdc: disable all layers before crtc shutdown

All plans must be disabled before the CRTC shutdown helping
the crtc to restart from a clean situation (without unwanted
planes already enable).

Signed-off-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220603134151.591997-1-yannick.fertre@foss.st.com

drm/doc: Add KUnit documentation

Explain how to run the KUnit tests present in the DRM subsystem and
clarify why the UML-only options were not added to the configuration
file present in drivers/gpu/drm/.kunitconfig [1] [2].

[1] https://lore.kernel.org/dri-devel/CABVgOSn8i=LO5p7830h2XU1Jgg0KrN0qTnxkOMhf1oTgxjaKKw@mail.gmail.com/
[2] https://lore.kernel.org/dri-devel/CAGS_qxqpiCim_sy1LDK7PLwVgWf-LKW+uNFTGM=T7ydk-dYcEw@mail.gmail.com/

Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: David Gow <davidgow@google.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220620160640.3790-4-jose.exposito89@gmail.com

drm/format-helper: Add KUnit tests for drm_fb_xrgb8888_to_rgb332()

Test the conversion from XRGB8888 to RGB332.

What is tested?

 - Different values for the X in XRGB8888 to make sure it is ignored
 - Different clip values: Single pixel and full and partial buffer
 - Well known colors: White, black, red, green, blue, magenta, yellow
   and cyan
 - Other colors: Randomly picked
 - Destination pitch

How to run the tests?

 $ ./tools/testing/kunit/kunit.py run --kunitconfig=drivers/gpu/drm/tests \
         --kconfig_add CONFIG_VIRTIO_UML=y \
         --kconfig_add CONFIG_UML_PCI_OVER_VIRTIO=y

Suggested-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: David Gow <davidgow@google.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220620160640.3790-3-jose.exposito89@gmail.com

drm/rect: Add DRM_RECT_INIT() macro

Add a helper macro to initialize a rectangle from x, y, width and
height information.

Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: David Gow <davidgow@google.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220620160640.3790-2-jose.exposito89@gmail.com

drm/ast: Enable primary plane with CRTC

As the CRTC requires a primary plane for display, ensure that the
primary plane is enabled with the CRTC.

Use drm_atomic_helper_check_crtc_state(). Add all affected planes
to the atomic state so that their state will be checked as well.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220617103226.25617-4-tzimmermann@suse.de

drm/simple-kms: Use drm_atomic_helper_check_crtc_state()

Simple-KMS helpers guarantee that the CRTC and plane enable
flags are synchronized. Implement this with atomic helpers
drm_atomic_helper_check_crtc_state() on the CRTC side, and
drm_atomic_helper_check_plane_state() on the plane side.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220617103226.25617-3-tzimmermann@suse.de

drm/atomic-helper: Add helper drm_atomic_helper_check_crtc_state()

Add drm_atomic_helper_check_crtc_state(), which contains tests common
to many CRTCs. The first added test verifies that an enabled CRTC has
at least one enabled primary plane.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220617103226.25617-2-tzimmermann@suse.de

drm/fb-helper: Fix out-of-bounds access

Clip memory range to screen-buffer size to avoid out-of-bounds access
in fbdev deferred I/O's damage handling.

Fbdev's deferred I/O can only track pages. From the range of pages, the
damage handler computes the clipping rectangle for the display update.
If the fbdev screen buffer ends near the beginning of a page, that page
could contain more scanlines. The damage handler would then track these
non-existing scanlines as dirty and provoke an out-of-bounds access
during the screen update. Hence, clip the maximum memory range to the
size of the screen buffer.

While at it, rename the variables min/max to min_off/max_off in
drm_fb_helper_deferred_io(). This avoids confusion with the macros of
the same name.

Reported-by: Nuno Gonçalves <nunojpg@gmail.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Nuno Gonçalves <nunojpg@gmail.com>
Fixes: 67b723f5b742 ("drm/fb-helper: Calculate damaged area in separate helper")
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: <stable@vger.kernel.org> # v5.18+
Link: https://patchwork.freedesktop.org/patch/msgid/20220621104617.8817-1-tzimmermann@suse.de

vfio/pci: Remove console drivers

Console drivers can create conflicts with PCI resources resulting in
userspace getting mmap failures to memory BARs.  This is especially
evident when trying to re-use the system primary console for userspace
drivers.  Use the aperture helpers to remove these conflicts.

v3:
* call aperture_remove_conflicting_pci_devices()

Reported-by: Laszlo Ersek <lersek@redhat.com>
Suggested-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220622140134.12763-4-tzimmermann@suse.de

drm: Implement DRM aperture helpers under video/

Implement DRM's aperture helpers under video/ for sharing with other
sub-systems. Remove DRM-isms from the interface. The helpers track
the ownership of framebuffer apertures and provide hand-over from
firmware, such as EFI and VESA, to native graphics drivers.

Other subsystems, such as fbdev and vfio, also have to maintain ownership
of framebuffer apertures. Moving DRM's aperture helpers to a more public
location allows all subsystems to interact with each other and share a
common implementation.

The aperture helpers are selected by the various firmware drivers within
DRM and fbdev, and the VGA text-console driver.

The original DRM interface is kept in place for use by DRM drivers.

v3:
* prefix all interfaces with aperture_ (Javier)
* rework and simplify documentation (Javier)
* rename struct dev_aperture to struct aperture_range
* rebase onto latest DRM
* update MAINTAINERS entry

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220622140134.12763-3-tzimmermann@suse.de

MAINTAINERS: Broaden scope of simpledrm entry

There will be more DRM drivers for firmware-provided framebuffers. Use
the existing entry for simpledrm instead of adding a new one for each
driver. Also add DRM's aperture helpers, which are part of the driver's
infrastructure.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220622140134.12763-2-tzimmermann@suse.de

drm/ast: Fix black screen when getting out of suspend

With an AST2600, the screen is garbage when going out of suspend.
This is because color settings are lost, and not restored on resume.
Force the color settings on DPMS_ON, to make sure the settings are correct.

I didn't write this code, it comes from the out-of-tree aspeed driver v1.13
https://www.aspeedtech.com/support_driver/

Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Venkat Tadikonda <venkateswara.rao@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220622124815.356035-1-jfalempe@redhat.com

drm/mcde: Fix refcount leak in mcde_dsi_bind

Every iteration of for_each_available_child_of_node() decrements
the reference counter of the previous node. There is no decrement
when break out from the loop and results in refcount leak.
Add missing of_node_put() to fix this.

Fixes: 5fc537bfd000 ("drm/mcde: Add new driver for ST-Ericsson MCDE")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220525115411.65455-1-linmq006@gmail.com

drm/connector: Remove usage of the deprecated ida_simple_xxx API

Use ida_alloc_xxx()/ida_free() instead of
ida_simple_get()/ida_simple_remove().
The latter is deprecated and more verbose.

Signed-off-by: Bo Liu <liubo03@inspur.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220617082319.7599-1-liubo03@inspur.com
Link: https://patchwork.freedesktop.org/patch/msgid/20220621190055.8323-1-jiangjian@cdjrlc.com

drm/panel: introduce ebbg,ft8719 panel

Add DRM panel driver for EBBG FT8719 6.18" 2246x1080 DSI video mode
panel, which can be found on some Xiaomi Poco F1 phones. The panel's
backlight is managed through QCOM WLED driver.

Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/BY5PR02MB7009B6FA7F17A3DA36DDA44CD9DF9@BY5PR02MB7009.namprd02.prod.outlook.com

drm/mipi-dsi: Introduce mipi_dsi_dcs_write_seq macro

A helper macro that can be used to simplify sending DCS commands.
It is useful in scenarios like panel initialization which can sometimes
involve sending lot of DCS commands.

Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/BY5PR02MB700952493EEB6F0E77DC8416D9DF9@BY5PR02MB7009.namprd02.prod.outlook.com

dt-bindings: display: Add bindings for EBBG FT8719

Add bindings for the EBBG FT8719 6.18" 2246x1080 DSI video mode panel,
which can be found on some Xiaomi Poco F1 phones. The backlight is
managed through the QCOM WLED driver.

Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/BY5PR02MB7009E821B0D4AC20E11F8F13D9DF9@BY5PR02MB7009.namprd02.prod.outlook.com